Philips TAT3217WT/00 3000 Series Earphones User Manual PDF

1 of 17
1 of 17

Summary of Content for Philips TAT3217WT/00 3000 Series Earphones User Manual PDF

User manual Register your product and get support at

www.philips.com/support

Headphones

3000 Series

TAT3217

1 Important safety instructions 2 Hearing safety 2 General information 2

2 Your True wireless earpieces 3 What's in the box 3 Other devices 3 Overview of your True wireless earpieces 4

3 Get started 5 Charge the battery 5 How to wear 6 Pair the earpieces with your Bluetooth device for the rst time 6 Pair the earpieces with another Bluetooth device 7

4 Use your earpieces 8 Connect the earpieces to your Bluetooth device 8 Power on/o 8 Manage your calls and music 8 Voice Assistant 9 Earpieces/charging case LED indicator status 9

9 Frequently asked questions 15

Contents

5 Reset the earpieces 10

6 Technical data 10

7 Notice 11 Declaration of conformity 11 Disposal of your old product and battery 11 Remove the integrated battery 11 Compliance with EMF 12 Environmental information 12 Notice of compliance 12

8 Trademarks 14

1 Important safety

instructions

Be sure to observe the following guidelines when using your headphones. Listen at reasonable volumes for reasonable periods of time. Be careful not to adjust the volume continuously upwards as your hearing adapts. Do not turn up the volume so high that you can't hear what's around you. You should use caution or temporarily discontinue use in potentially hazardous situations. Excessive sound pressure from earpieces and headphones can cause hearing loss. Using headphones with both ears covered while driving is not recommended and may be illegal in some areas. For your safety, avoid distractions from music or phone calls while in trac or other potentially dangerous environments.

General information To avoid damage or malfunction:

Operating and storage temperatures and humidity Store in a place where the

temperature is between -20C (-4F) and 50C (122 F) with up to 90% relative humidity.

Operate in a place where the temperature is between 0C (32F) and 45C (113 F) with up to 90% relative humidity.

Battery life may be shorter in high or low temperature conditions.

Replacement of a battery with an incorrect type risks severely damaging the headphones and the battery (for example, in the case of some lithium battery types).

Danger

To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.

Caution

Do not expose headphones to excessive heat. Do not drop your headphones. Headphones shall not be exposed to dripping

or splashing. (Refer to the IP rating of specic product)

Do not allow your headphones to be submerged in water.

Do not charge your headphones when the connector or socket is wet.

Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.

If cleaning is required, use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.

The integrated battery shall not be exposed to excessive heat such as sunshine, re or the like.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

To achieve the specic IP rating, the charging slot cover must be closed.

Disposal of a battery into re or a hot oven, or mechanically crushing or cutting a battery, can result in an explosion.

Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of ammable liquid or gas.

A battery subjected to extremely low air pressure may result in an explosion or the leakage of ammable liquid or gas.

2 EN

Hearing safety

2 Your True wireless earpieces

What's in the box

Congratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips oers, register your product at www.philips.com/support. With these Philips True wireless earpieces you can: Enjoy convenient wireless handsfree calls Enjoy and control music wirelessly Switch between calls and music

Other devices

A mobile phone or device (e.g. notebook, tablet, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible with the earpieces.

Philips True wireless earpieces Philips TAT3217

Silicone ear tip covers x 3 pairs

EN 3

Quick start guide

USB-C charging cable (for charging only)

Global Warranty

Safety leaet

Headphones

Series

CTN

Overview of your True wireless earpieces

Multi-function touch (MFT)

LED indicator (earpieces)

Microphone

LED indicator (BT pairing and

reset)

Bluetooth pair button

LED indicator (battery state or

charging state)

USB-C charging slot

7

1

3

2

3

6

5

4

1

2

3

4

5

6

7

4 EN

3 Get started

Charge the battery

Before you use your headphones, place them in the charging case and charge the battery for 2 hours for optimum battery capacity and lifetime.

Use only the original USB-C charging cable to avoid any damage.

Finish your call before charging. Connecting the earpieces to charge will power them o.

EN 5

Note

Charging case

Plug one end of the USB-C cable into the charging case and the other end into the power source.

The charging case serves as a portable backup battery for charging the earpieces. When the charging case is fully charged, it will fully recharge the earpieces 3 times.

Tip

Earpiece

The earpieces start charging and the blue LED light goes on

When the earpieces are fully charged, the blue light will go o

Take out the earpieces and remove the insulation labels. Put the earpieces back into the charging case and close the lid.

Normally, a full charge takes 2 hours (for the earpieces or charging case) by USB cable.

Tip

How to wear

Select suitable ear tips for optimum t

A tight, secure t will provide the best sound quality and noise isolation.

Pair the earpieces with your Bluetooth device for the rst time

Test which ear tip provides you with the best sound and wearing comfort.

3 sizes of silicone ear tip covers are provided: large, medium and small.

L M S

1

2

Check left or right orientation of the earpieces.

Insert the earpieces into the ears and twist slightly until a secure t is achieved.

Insert the earpieces

Turn on the Bluetooth function of your Bluetooth device.

Pair the earpieces with your Bluetooth device. Refer to the user manual of your Bluetooth device.

After powering on, if the earpieces cannot nd any previously connected Bluetooth device, it will automatically switch to pairing mode.

The LEDs on both earpieces ash white and blue alternately

The earpieces are now in pairing mode and are ready to pair with a Bluetooth device (e.g. a mobile phone)

03"

1

2

1

2

Make sure that the earpieces are fully charged and powered o.

Open the cover of the charging case. Press and hold the pairing button for approximately 3 seconds.

3

4

6 EN

Note

Single earpiece (Mono mode)

Take either right or left earpiece out from charging case for Mono use. The earpiece will power on automatically.

Philips TAT3217

The following example shows you how to pair the earpieces with your Bluetooth device.

Turn on the Bluetooth function of your Bluetooth device, select Philips TAT3217.

Enter the earpieces' password 0000 (4 zeros) if prompted. For those devices featuring Bluetooth 3.0 or higher, there is no need to enter a password.

1

2

EN 7

Voice assistant is disabled in Mono mode. Take the second earpiece from the charging

case and they will pair with each other automatically.

Note

The earpieces store 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.

Pair the earpieces with another Bluetooth device

If you want to pair another Bluetooth device with the earpieces, just put them into pairing mode, (press button on box for 3 seconds with both earpieces inside and the cover open), then discover the second device as per normal pairing.

Note

The blue LED ashes

The earpieces will search the last connected Bluetooth device and reconnect to it automatically.

4 Use your earpieces

Connect the earpieces to your Bluetooth device

1

2

If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manually.

If the earpieces fails to connect to any Bluetooth device within 3 minutes, it will turn

o automatically to save the battery life. In some Bluetooth devices, connection may not

be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earpieces to the Bluetooth device manually.

Turn on the Bluetooth function of your Bluetooth device.

Open the charging case cover.

8 EN

Note

Tip

Task

Turn the earpieces on

Take earpiec- es out of the charging case

Put earpieces back into the charging case

Turn the earpieces o

Power on/o

Operation

Manage your music and calls (Stereo mode)

Music control

Play or pause music

Next track L / R earpiece

Double tap

Adjust volume +/-

Via mobile phone control

Right earpiece

Tap and hold for 1 second

Task Operation

Call control

Pick up/ Switch caller during a call

Hang up call L / R earpiece

Tap and hold for 1 second

L / R earpiece

Double tap

Task Operation

Reject call L / R earpiece

Tap and hold for 2 seconds

Multi- function touch

Multi- function touch

Multi- function touch

EN 9

Charging case LED indicator status

When charging Indicator

Battery low

Relative adequate battery

White LED lights up

Amber LED lights up

Battery low

Relatively adequate battery

O

Amber slowly blinks for 4 cycles

In use and cover is open

Indicator

Indicator

Earpieces LED indicator status

Earpieces status

The earpieces are connected to a Bluetooth device

The earpieces are ready for pairing

The earpieces are on but not connected to a Bluetooth device

Low battery level (earpieces)

Blue LED blinks 2x every 5 seconds

The LED ashes blue and white alternately

Blue LED blinks every 5 seconds

Battery is fully charged (charging case)

Refer to case LED

White LED blinks every second (auto turn o after 3 minutes)

Voice Assistant

OperationTask Button

Left earpiece

Trigger Voice (Siri/Google) Assistant

Tap and hold for 2 seconds

Left earpiece

Stop Voice Assistant

Single tap

* Voice assistant is disabled in Mono mode.

Manage your music and calls (Mono mode) Music control

Play or pause music

Next track L / R earpiece

Double tap

Adjust volume +/-

Via mobile phone control

L / R earpiece

Tap and hold for 1 second

Task Operation

Call control

Pick up/ Switch caller during a call

Hang up call L / R earpiece

Tap and hold for 1 second

L / R earpiece

Double tap

Task Operation

Reject call L / R earpiece

Tap and hold for 2 seconds

Multi- function touch

Multi- function touch

5 Reset the earpieces

On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT3217 from the device list.

Turn o the Bluetooth function of your Bluetooth device.

Return earpieces to charging case, close the lid and re-open the lid.

Press button on box twice.

Follow steps in Use your earpieces- connect the earpieces to your Bluetooth device.

Pair the earpieces with your Bluetooth device, select Philips TAT3217.

If you encounter any pairing or connection issue, you can follow the following procedure to reset your earpieces to factory default settings.

If there is no response from the earpieces, you can follow the below step to reset the hardware of your earpieces.

Tap and hold multi-function touch for 10 seconds.

6 Technical data

Music play time: 6 + 20 hours Talk time: 6 hours Charging time: 2 hours Lithium-ion battery 40 mAh on each earpiece, Lithium-ion battery 460 mAh on charging case Bluetooth version: 5.2 Compatible Bluetooth proles: HFP (Hands-Free Prole) A2DP (Advanced Audio

Distribution Prole) AVRCP (Audio Video Remote

Control Prole) Supported audio codecs: SBC Frequency range: 2.402-2.480 GHz Transmitter power: < 13 dBm Operating range: Up to 10 meters (33 feet) USB-C port for charging Low battery warning: available

Specications are subject to change without notice.

10 EN

Note

1

2

3

4

5

6

7 Notice

Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can nd the Declaration of Conformity on www.p4c.philips.com.

Declaration of conformity

Dispose of your old product and battery

Your product is designed and manufactured with high quality materials and components which can be recycled and reused.

This symbol on a product means that the product is covered by European Directive 2012/19/EU.

This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an ocial collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the earpieces.

Make sure the earpieces are disconnected from the charging case before removing the battery.

Make sure the charging case is disconnected from the USB charging cable before removing the battery.

EN 11

Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic elds.

Environmental information

All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buer) and polyethylene (bags, protective foam sheet). Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Notice of compliance

The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

FCC rules

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase. the separation between equipment and receiver. Plug the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Canada: This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Caution: The user is cautioned that changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

12 EN

IC Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) Lappareil ne doit pas produire de brouillage; (2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. CAN ICES-3(B)/NMB-3(B)

EN 13

8 Trademarks

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.

Bluetooth

Siri is a trademark of Apple Inc., registered in the U.S. and other countries.

Siri

Google and Google Play are trademarks of Google LLC.

Google

14 EN

9 Frequently asked questions

My Bluetooth earpieces do not turn on. The battery level is low. Charge the earpieces.

I cannot pair my Bluetooth earpieces with my Bluetooth device. Bluetooth is disabled. Turn on your device and enable the Bluetooth func- tion before you turn on your earpieces.

Pairing does not work. Put both earpieces into charging

case. Make sure you have disabled the

Bluetooth function of any previously connected Bluetooth devices.

On your Bluetooth device, delete Philips TAT3217 from the Bluetooth list.

Pair your earpieces (see Pair the earpieces with your Bluetooth device for the rst time on page 6).

The Bluetooth device cannot nd the earpieces. The earpieces may be connected to

a previously paired device. Turn o the connected device or move it out of range.

Pairing may have been reset or the earpieces have been previously paired with another device. Pair the earpieces with the Bluetooth device again as described in the user manual. (see Pair the earpieces with your Bluetooth device for the rst time on page 6).

My Bluetooth earpieces are connected to a Bluetooth stereo-enabled mobile phone, but music only plays on the mobile phone speaker. Refer to the user manual of your mobile phone. Select to listen to music through the earpieces.

The audio quality is poor and a crackling noise can be heard. The Bluetooth device is out of range.

Reduce the distance between your earpieces and Bluetooth device, or remove obstacles between them.

Charge your earpieces.

The audio quality is poor when stream- ing from a mobile phone, is very slow or streaming does not work at all. Make sure your mobile phone not only supports (mono) HSP/HFP but also supports A2DP and is BT4.0x (or higher) compatible (see Technical data on page 11).

APP DOWNLOAD Scan the QR code/press 'Download'

button or search 'Philips Headphones' in Apple App Store or Google Play to

download App.

EN 15

UM_TAT3217_00_EN_V1.0

Model: TAT3217LC

2021 MMD Hong Kong Holding Limited. All rights reserved. Specications are subject to change without notice. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its aliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. All other company and

Manualsnet FAQs

If you want to find out how the 3000 series Philips works, you can view and download the Philips TAT3217WT/00 3000 Series Earphones User Manual on the Manualsnet website.

Yes, we have the User Manual for Philips 3000 series as well as other Philips manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Philips 3000 series. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Philips TAT3217WT/00 3000 Series Earphones User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Philips TAT3217WT/00 3000 Series Earphones User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Philips TAT3217WT/00 3000 Series Earphones User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Philips TAT3217WT/00 3000 Series Earphones User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Philips TAT3217WT/00 3000 Series Earphones User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.