Contents

Philips OST690/10 OST690 Boombox User Manual PDF

1 of 16
1 of 16

Summary of Content for Philips OST690/10 OST690 Boombox User Manual PDF

www.philips.com/welcome

OST690

Always there to help you

User Manual

Question? Contact Philips

Register your product and get support at

2EN

Contents 1 Important 3

2 Your Speaker System 4 Introduction 4 What's in the box 4 Overview of the system 5

3 Get started 6 Connect power 6 Turn on 7 Turn off 7 Switch to standby mode 7

4 Play 8 Play from a USB device 8 Play from Bluetooth-enabled device 9 Play from an external audio device 9

5 Listen to FM radio 10 Tune to FM radio stations 10 Store radio stations automatically 10 Store radio stations manually 10 Select a preset radio station 10

6 Other features 11 Charge your mobile phone 11 Adjust display brightness 11 Adjust volume 11 Enhance bass 11

7 Product information 12 Specifications 12 Supported MP3 disc formats 12 USB playability information 12

8 Troubleshooting 13 About Bluetooth device 14

9 Notice 14

3 EN

1 Important Read these instructions. Follow all instructions. Do not block any ventilation openings.

Install in accordance with the manufacturer's instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or otherapparatus(includingamplifiers)that produce heat.

Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the unit.

Only use attachments or accessories specifiedbythemanufacturer.

Unplug this unit during lightning storms or when unused for long periods of time.

Referallservicingtoqualifiedservice personnel. Servicing is required when the unit has been damaged in any way.

Battery usage CAUTION To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit: Install all batteries correctly, + and - as

marked on the unit. Do not mix batteries (old and new or

carbonandalkaline,etc.). Remove batteries when the unit is not

used for a long time. Batteries (battery pack or batteries

installed)shallnotbeexposedtoexcessive heatsuchassunshine,fireorthelike.

Tropical condition has been considered and complied.

The unit shall not be exposed to dripping or splashing.

Do not place any sources of danger on theunit(e.g.liquidfilledobjects,lighted candles).

Where the MAINS plug or an appliance coupler is used as the disconnect device,

the disconnect device shall remain readily operable.

Warning

Never remove the casing of this unit. Never place this unit on other electrical equipment.

4EN

2 Your Speaker System

Introduction With this speaker system, you can: listen to FM radio; enjoy audio from Bluetooth-enabled

devices, USB device, and other external audio devices; and

charge your mobile phone with the supplied USB cable.

The system offers you Dynamic Bass Boost (DBB)toenrichsound.

What's in the box Check and identify the contents of the package: Main unit AC power cord USB cable for charging Short user manual Safety&noticeleaflet

5 EN

Overview of the system

a Source selector

Select a source: BLUETOOTH, FM, or USB.

b LED indicator

c ON/OFF Turn the system on or off.

d Connect a USB storage device. Charge a mobile phone with the

supplied USB cable.

e AUDIO IN Connect an external audio device.

f Slider Stabilize the mobile phone while

charging.

g VOLUME Adjust volume.

h - TUNING + Tune to FM radio stations manually.

a b

c d

e

l

m

n

k

h i j

g

f

r q

p o

MODE PROG

SEARCH -PRESET - PROGPRESET +SEARCH +

ALB ALB

i DBB Turn dynamic bass enhancement on

or off.

j Display panel

k FM antenna Improve FM radio reception.

l ALB/PRESET -/+ Select a preset radio station. Skip to the previous or next album. Adjust display brightness.

m MODE Selectarepeatorshufflemode. Activate brightness adjustment.

n / SEARCH+/- Skip to the previous or next track. Tune to FM radio stations automatically. Search within a track.

o PROG Program the play sequence of tracks. Program FM radio stations.

6EN

p Open or close the compartment.

q Start or pause play.

r Stop play. Erase a program.

3 Get started Always follow the instructions in this chapter in sequence.

Connect power The system can be powered by either AC power or batteries.

Option 1: Battery power

Caution

Batteries contain chemical substances, so they should be disposed of properly.

Note

Batteries are not supplied with the accessories.

1 Open the battery compartment. 2 Insert6batteries(type:R14/UM2/CCELL)

withcorrectpolarity(+/-)asindicated. 3 Close the battery compartment.

7 EN

Option 2: AC power

Warning

Risk of product damage! Make sure that the power supply voltage corresponds to the voltage printed on the back or the underside of the system.

Risk of electric shock! When you disconnect the AC power, always pull the plug from the socket. Never pull the cord.

Connect the AC power cord to: the AC~ MAINS socket on the back of the

system. the wall outlet.

Tip

To save energy, turn off the system after use.

Turn on Switch the power slide to the ON position. The system switches to the last selected

source. The LED indicator lights up.

Turn off Switch the power slide to the OFF position. The LED indicator turns off.

Switch to standby mode In AC power supply mode, if there is no

operation for 3 hours, this product will switch to standby mode automatically for energy-saving.Afterthefirst30-minute inactivity, the display will start to show the remaining time before entering standby mode(from149:59to0:00).

In DC power supply mode, if there is no operation for 15 minutes, this product will switch to standby mode automatically forenergy-saving.Afterthefirst5-minute inactivity, the display will start to show the remaining time before entering standby mode(from9:59to0:00).

You may press to cancel the countdown and resume normal operation, or continue charging.

8EN

4 Play

Play from a USB device Note

Make sure that your USB device contains playable audio content.

1 Rotate the source selector to the USB position.

2 Press to open the compartment. 3 Insert the USB device into the socket

inside the compartment. Play starts automatically. If not, press

.

Note

The USB socket is not compatible with music playback from your smartphone.

Control play In USB mode, you can control play through the following operations.

/ Selectanaudiofile; Press and hold to fast-forward or fast-reverse the track during playback, then release to resume play.

ALB-/ ALB+

Skip to the previous or next MP3/ WMA album. Start or pause play. Stop play.

MODE [ ]: Play the current track repeatedly. [ ]: Play the current album repeatedly. [ ]: Play all tracks repeatedly. [ ]: Play tracks randomly. To return to normal play, press MODE repeatedly until the repeat orshuffleiconsdisappear.

Program tracks In USB mode, you can program the play sequence of tracks. A maximum of 20 tracks can be programmed. 1 Press to stop playback. 2 Press PROG to activate the programming

mode. [PROG] is displayed and [P01] begins

to blink.

3 For MP3/WMA tracks, press ALB -/ALB + to select an album.

4 Press / to select a track number, then press PROGtoconfirm.

5 Repeat steps 3-4 to program more tracks. 6 Press to play the programmed tracks.

During play, [PROG] (program)is displayed.

To erase the program, press twice.

9 EN

Play from Bluetooth-enabled device

Note

The effective operating range between the system and thepaireddeviceisapproximately10meters(30feet).

Any obstacle between the system and the device can reduce the operational range.

Compatibility with all Bluetooth devices is not guaranteed.

1 Rotate the source selector to the BLUETOOTH position.

2 On your Bluetooth device, enable Bluetooth and search for Bluetooth devices that can be paired (refer to the user manualofthedevice).

3 When [OST690] is displayed on your device, select it to start pairing and connection. After successful pairing and connection,

the system beeps twice.

4 Play audio on your device. Audio streams from your device to this

system.

To disconnect the Bluetooth-enabled device: Deactivate Bluetooth on your device; or Move the device beyond the

communication range.

To clear Bluetooth pairing history: Press and PROG together for 3 seconds. The current Bluetooth connection is

disconnected. After successful clearing, [CLR](clear)

blinks for 5 seconds, then [-] scrolls on the display.

Play from an external audio device You can also listen to an external audio device such as an MP3 player through this system. 1 Press to open the compartment. 2 Connect an audio cable (3.5mm, not

supplied)to: the AUDIO IN socket inside the

compartment. the headphone socket on an external

device. The system switches to Audio-in mode

automatically.

3 Play audio on the external device (see the

usermanualofthedevice).

10EN

5 Listen to FM radio

Tune to FM radio stations Note

For better reception, fully extend and adjust the position of the FM antenna.

1 Rotate the source selector to the FM position.

2 Press SEARCH +/-. The system tunes to a station with

strong reception automatically.

3 Repeat step 2 to tune to more stations.

To tune to a radio station manually: Rotate the tuning knob slowly.

Store radio stations automatically In tuner mode, press and hold PROG for 2 seconds. The system stores all the available FM radio

stations. Thefirststoredradiostationisbroadcast

automatically.

Store radio stations manually Note

You can store a maximum of 20 FM radio stations.

1 Tune to an FM radio station. 2 Press PROG to activate the storing mode.

3 Press PRESET + or PRESET - to allocate a number(1to20)tothisradiostation,then press PROGtoconfirm. The preset number and the frequency

of the preset station are displayed.

4 Repeat the above steps to store other stations.

Note

To remove a pre-stored FM radio station, store another station in its place.

Select a preset radio station In FM tuner mode, press PRESET + or PRESET - to select a preset radio station.

11 EN

6 Other features

Charge your mobile phone Note

Make sure that you have switched on the system.

1 Rotate the source selector to BLUETOOTH/CHR or FM/CHR

2 Press to open the compartment. 3 Connect the supplied USB cable to:

the socket inside the compartment. the USB socket on your mobile phone. The charging icon is displayed on your

phone.

4 Adjust the slider inside the compartment

to stabilize your phone.

BLUETOOTH /CHR

USB

FM/CHR

BLUETOOTH /CHR

USB

FM/CHR

5 Close the compartment.

Note

You cannot charge your mobile phone when the system is powered by the batteries.

Adjust display brightness

1 Press and hold MODE for 3 seconds. 2 Press ALB/PRESET -/+ repeatedly to adjust

the display brightness.

Adjust volume Rotate the VOLUME knob to adjust volume.

Enhance bass To turn dynamic bass boost on or off, switch the DBB slide to the ON or OFF position.

12EN

7 Product information

Note

Product information is subject to change without prior notice.

Specifications

Amplifier Max Output Power 6W per channel x 2 Frequency Response 125 -16000 Hz, -3dB Signal to Noise Ratio >55 dBA Total Harmonic Distortion

<1 %

Audio-in Input 650 mV RMS

Tuner Tuning Range 87.5 - 108 MHz Tuning Grid 50 kHz Sensitivity - Mono, 26dB S/N Ratio - Stereo, 46dB S/N Ratio

<22 dBf <41 dBf

Total Harmonic Distortion <3% Signal to Noise Ratio >50 dBA

Bluetooth Standard Bluetooth Standard Version 2.1+EDR Range 10m(freespace)

Speaker Speaker Impedance 8 ohm Speaker Driver 4"

General Power supply - AC Power - Battery

220-240 V~, 50/60 Hz; 6 x 1.5 V R14/UM2/C CELL

Operation Power Consumption

15 W

Standby Power Consumption

<0.5 W

Max.Loading(USB) 5 V 1 A Dimensions - Main Unit (WxHxD)

447 x 230 x 116 mm

Weight(MainUnit) 2.2 kg

Supported MP3 disc formats ISO9660, Joliet Maximum title number: 512 (depending on

filenamelength) Maximum album number: 255 Supported sampling frequencies: 32 kHz,

44.1kHz, 48 kHz SupportedBit-rates:32~256(kbps),

variable bit rates

USB playability information Compatible USB devices: USBflashmemory(USB2.0orUSB1.1) USBflashplayers(USB2.0orUSB1.1) memory cards (requires an additional card

readertoworkwiththisapparatus)

Supported formats: USBormemoryfileformatFAT12,FAT16,

FAT32(sectorsize:512bytes) MP3bitrate(datarate):32-320Kbpsand

variable bit rate WMA v9 or earlier Directory nesting up to a maximum of 8

levels Number of albums/ folders: maximum 99 Number of tracks/titles: maximum 999

13 EN

ID3 tag v2.0 or later File name in Unicode UTF8 (maximum

length:128bytes)

Unsupported formats: Empty albums: an empty album is an album

thatdoesnotcontainMP3/WMAfiles,and is not be shown in the display.

Unsupportedfileformatsareskipped.For example,Worddocuments(.doc)orMP3 fileswithextension.dlfareignoredand not played.

AAC,WAV,PCMaudiofiles DRMprotectedWMAfiles(.wav,.m4a,

.m4p,.mp4,.aac) WMAfilesinLosslessformat

8 Troubleshooting Warning

Never remove the casing of this device.

To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips Web page (www.philips.com/support).Whenyoucontact Philips, make sure that the device is nearby and the model number and serial number are available.

No power Ensure that the AC power plug of the unit

is connected properly. Ensure that there is power at the AC

outlet. Insert the batteries with their polarities

(+/signs)alignedasindicated. Replace the battery.

No sound or poor sound Adjust the volume.

No response from the unit Disconnect and reconnect the AC power

plug, then turn on the system again.

USB device not supported The USB device is incompatible with the

apparatus. Try another one.

Poor radio reception Increase the distance between the unit and

your TV or VCR. Fully extend the FM antenna.

14EN

About Bluetooth device

Music playback is unavailable on the system even after successful Bluetooth connection. The device cannot be used with the

system to play music.

The audio quality is poor after connection with a Bluetooth-enabled device. The Bluetooth reception is poor. Move

the device closer to the system or remove any obstacle between the device and the system.

Cannot connect with the system. Thedevicedoesnotsupporttheprofiles

required for the system. The Bluetooth function of the device is not

enabled. Refer to the user manual of the device for how to enable the function.

The system is not in the pairing mode. The system is already connected with

another Bluetooth-enabled device. Disconnect that device or all other connected devices and then try again.

The paired device connects and disconnects constantly. The Bluetooth reception is poor. Move

the device closer to the system or remove any obstacle between the device and the system.

For some devices, the Bluetooth connection may be deactivated automatically as a power-saving feature. This does not indicate any malfunction of the system.

9 Notice Anychangesormodificationsmadetothis device that are not expressly approved by WOOX Innovations may void the users authority to operate the equipment.

This product complies with the radio interference requirements of the European Community.

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/ EC. Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.

Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed with normal household waste.Please inform yourself about the local

15 EN

rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separateintothreematerials:cardboard(box), paperpulp(buffer)andpolyethylene(bags, protectivefoamsheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. Class II equipment symbol

This symbol indicates that the unit has a double insulation system.

Note

The type plate is located on the bottom of the apparatus.

Specifications are subject to change without notice 2013 WOOX Innovations Limited. All rights reserved. This product was brought to the market by WOOX Innovations Limited or one of its affiliates, further referred to in this document as WOOX Innovations, and is the manufacturer of the product. WOOX

Manualsnet FAQs

If you want to find out how the OST690/10 Philips works, you can view and download the Philips OST690/10 OST690 Boombox User Manual on the Manualsnet website.

Yes, we have the User Manual for Philips OST690/10 as well as other Philips manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Philips OST690/10. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Philips OST690/10 OST690 Boombox User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Philips OST690/10 OST690 Boombox User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Philips OST690/10 OST690 Boombox User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Philips OST690/10 OST690 Boombox User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Philips OST690/10 OST690 Boombox User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.