Peterbilt Model 520 VMUX Body Builder Operator’s Manual PDF

Release Date 5/18/2021

This page is intentionally left blank.

Peterbilt Motors Company ii

BODY BUILDER MANUAL CONTENTS SECTION 1: INTRODUCTION 1-1 SECTION 2: SAFETY AND COMPLIANCE

SAFETY SIGNALS 2-1 FEDERAL MOTOR VEHICLE SAFETY STANDARDS AND COMPLIANCE 2-2

NOISE AND EMISSIONS REQUIREMENTS 2-3 FUEL SYSTEM 2-4 COMPRESSED AIR SYSTEM 2-4 EXHAUST AND EXHAUST AFTER-TREATMENT SYSTEM 2-5 COOLING SYSTEM 2-6 AIR INTAKE SYSTEM 2-6 CHARGE AIR COOLER SYSTEM 2-6

SECTION 3: DIMENSIONS

INTRODUCTION 3-1 ABBREVIATIONS 3-1 OVERALL DIMENSIONS 3-1

FRAME RAILS 3-10 FRAME HEIGHT CHARTS 3-12 REAR SUSPENSION LAYOUTS 3-19 Reyco 79KB Single 3-20

Reyco 102AR Single 3-21 Neway ADZ252 3-22 Neway ADZ369/378 3-23 Peterbilt Air Leaf 3-24 Peterbilt Air Trac Single 3-25 Peterbilt Air Trac Tandem 3-26 Peterbilt Air Trac Tri-Drive 3-27 Peterbilt Low Air Leaf 3-28 Chalmers 854 3-29 Hendrickson HMX 3-30 Hendrickson RT/RTE 3-31 Hendrickson HN 3-32 Hendrickson R 3-33 Hendrickson RS 3-34

PUSHER AND TAG LAYOUTS 3-35 Hendrickson 3-35

Watson-Chalin 3-39 EXHAUST HEIGHT CALCULATIONS 3-43 GROUND CLEARANCE CALCULATIONS 3-44 OVERALL CAB HEIGHT CALCULATIONS 3-45 FRAME COMPONENTS 3-46

SECTION 4: BODY MOUNTING

INTRODUCTION 4-1 FRAME RAILS 4-1 CRITICAL CLEARANCES 4-2 BODY MOUNTING USING BRACKETS 4-3 Brackets 4-4 Mounting Holes 4-5 Frame Drilling 4-6 BODY MOUNTING USING UBOLTS 4-7 Rear Body Mount 4-9

TABLE OF CONTENTS

Peterbilt Motors Company iii

SECTION 5: FRAME MODIFICATIONS INTRODUCTION 5-1 DRILLING RAILS 5-1 MODIFYING FRAME LENGTH 5-1 CHANGING WHEELBASE 5-1 CROSSMEMBERS 5-3 TORQUE REQUIREMENTS 5-4 WELDING 5-4

SECTION 6: CAN COMMUNICATIONS INTRODUCTION 6-1 CAN COMMUNICATIONS ACRONYM LIBRARY 6-1 SAE J1939 6-2 PARAMETER GROUP NUMBER 6-2 SUSPECT PARAMETER NUMBER 6-2 CAN MESSAGES AVAILABLE ON BODY CONNECTIONS 6-3

SECTION 7: ELECTRICAL INTRODUCTION 7-1 ELECTRICAL ACRONYM LIBRARY 7-1 ELECTRICAL WIRING CIRCUIT CODES 7-2 MULTIPLEX SYSTEM 7-3 CAN Bus System Overview 7-3 CAN Bus Speeds and Circuit Designation 7-3 ELECTRICAL COMPONENT OVERVIEW 7-4 IN CAB CAN BASED MESSAGING CONNECTOR 7-5 RP1226 Connector 7-5 RP1226 Connector Locations 7-6 ELECTRIC ENGAGED EQUIPMENT 7-7 RP170 Connector 7-7 ENGINE HARNESS 12 PIN CONNECTOR 7-12 PACCAR MX Engines 7-12 Cummins Engines 7-14 Engine Harness Connection Location 7-15 ENGINE HARNESS 8 PIN CONNECTOR 7-17 POWER DISTRIBUTION CENTER 7-18 CHASSIS MODULE 7-20 CHASSIS MODULE FUNCTION DESIGNATIONS 7-21 FUSE GROUPS 7-22 ELECTRIC OVER AIR SOLENOIDS 7-24 SWITCHES 7-27 SPARE POWER 7-28 TRANSMISSION BACKUP SIGNALS 7-29 LIFT AXLES (PUSHER & TAG) 7-30 DIGITAL DISPLAY 7-31 TELLTALE ICONS 7-31 Body Builder Telltale Locations 7-32 SECTION 8: POWER TAKE-OFF (PTO)

INTRODUCTION 8-1 TRANSMISSION MOUTED PTO GENERAL 8-1 Manual Transmission 8-1 Automatic Transmission 8-2 Installation Clearances 8-2 FRONT ENGINE PTO 8-3

TABLE OF CONTENTS

Peterbilt Motors Company iv

REAR ENGINE PTO 8-4 INSTALLTION OF PTO MODEL 8-5 Chelsea 890 8-5 MX PTO MODE CONTROL (PMC) 8-6 MX PTO MODE ACTIVATION 8-6 MX PTO MODE CONTROL LOCATION 8-6 MX PTO MODE FEATURES 8-7 MX PTO MODE PROTECTIONS AND LIMITS 8-7 MX PTO SPEED CONTROL (PSC) FEATURES 8-8 MX PTO SPEED CONTROL INTERLOCKS 8-9 PTO SPEED CONTROL ICONS 8-9 REMOTE PMC CONNECTIONS 8-10 PTO MODE CONTROL FLOW CHARTS 8-11 MX PTO TROUBLESHOOTING GUIDE 8-12

Peterbilt Motors Company 1-1

SECTION 1 INTRODUCTION

The Peterbilt 520 Body Builder Manual was designed to provide body builders with a comprehensive information set to guide the body planning and installation process. Use this information when installing bodies or other associated equipment.

This manual contains appropriate dimensional information, guidelines for mounting bodies, modifying frames, electrical wiring information, and other information useful in the body installation process.

The Peterbilt 520 Body Builder Manual can be very useful when specifying a vehicle, particularly when the body builder is involved in the vehicle definition and ordering process. Information in this manual will help reduce overall costs through optimized integration of the body installation with vehicle selection. Early in the process, professional body builders can often contribute valuable information that reduces the ultimate cost of the body installation.

In the interest of continuing product development, Peterbilt reserves the right to change specifications or products at any time without prior notice. It is the responsibility of the user to ensure that he is working with the latest released information. Check Peterbilt.com for the latest released version.

If you require additional information or reference materials, please contact your local Peterbilt dealer.

This page is intentionally left blank.

SECTION 2 SAFETY AND COMPLIANCE SAFETY SIGNALS There are a number of alerting messages in this book. Please read and follow them. They are there for your protection and information. These alerting messages can help you avoid injury to yourself or others and help prevent costly damage to the vehicle.

Key symbols and signal words are used to indicate what kind of message is going to follow. Pay special attention to comments prefaced by WARNING, CAUTION, and NOTE. Please dont ignore any of these alerts.

Warnings, cautions, and notes WARNING When you see this word and symbol, the message that follows is especially vital. It signals a

potentially hazardous situation which, if not avoided, could result in death or serious injury. This message will tell you what the hazard is, what can happen if you dont heed the warning, and how to avoid it.

Example: WARNING! Be sure to use a circuit breaker designed to meet liftgate amperage requirements. An incorrectly specified circuit breaker could result in an electrical overload or fire situation. Follow the liftgate installation instructions and use a circuit breaker with the recommended capacity.

CAUTION Signals a potentially hazardous situation which, if not avoided, could result in minor or moderate injury or damage to the vehicle.

Example:

CAUTION: Never use a torch to make a hole in the rail. Use the appropriate drill bit.

NOTE Provides general information: for example, the note could warn you on how to avoid damaging your vehicle or how to drive the vehicle more efficiently.

Example:

Note: Be sure to provide maintenance access to the battery box and fuel tank fill neck.

2 SAFETY AND COMPLIANCE

Peterbilt Motors Company 2-2

FEDERAL MOTOR VEHICLE SAFETY STANDARDS AND COMPLIANCE As an Original Equipment Manufacturer, Peterbilt Motors Company ensures that our products comply with all applicable U.S. or Canadian Federal Motor Vehicle Safety Standards. However, the fact that this vehicle has no fifth wheel and that a Body Builder (Intermediate or Final Stage Manufacturer) will be doing additional modifications means that the vehicle was incomplete when it left the build plant.

Incomplete Vehicle Certification An Incomplete Vehicle Document is shipped with the vehicle, certifying that the vehicle is not complete. See Figure 21. In addition, affixed to the drivers side door frame or edge is an Incomplete Vehicle Certification label. See Figure 22.

NOTE These documents list the U.S. or Canadian Federal Motor Vehicle Safety Standard regulations that the vehicle complied with when it left the build plant. You should be aware that if you add, modify or alter any of the components or systems covered by these regulations, it is your responsibility as the Intermediate or Final Stage Manufacturer to ensure that the complete vehicle is in compliance with the particular regulations upon completion of the modifications.

FIGURE 2-1. Incomplete Ve- hicle Certification Document

Tire, Rim and Weight Rating Data label

Safety Mark (Canadian Registry Only)

Incomplete Vehicle Certification Label

U.S. EPA Noise Label (U.S. registered vehicles only)

Final Stage Manufacturer Label to be installed by Final Stage Manufacturer

Chassis Serial Number

Vehicle Emission Control Information Label

Major Components and Weights Label

FIGURE 2-2. Locations of Certifica- tion Labels - Drivers Door and Frame

As the Intermediate or Final Stage Manufacturer, you should retain the Incomplete Vehicle Document for your records. In addition, you should record and retain the manufacturer and serial number of the tires on the vehicle. Upon completion of the vehicle (installation of the body and any other modifications), you should affix your certification label to the vehicle as required by Federal law. This tag identifies you as the Intermediate or Final Stage Manufacturer and certifies that the vehicle complies with Federal Motor Vehicle Safety Standards. (See Figure 22.) Be advised that regulations affecting the intermediate and final stage manufacturer may change without notice. Ensure you are referencing the most updated copy of the regulation during the certification and documentation processes.

In part, if the final stage manufacturer can complete and certify the vehicle within the instruction in the incomplete vehicle document (IVD) the certification label would need a statement that reads, This vehicle has been completed in accordance with the prior manufacturers IVD where applicable. This vehicle conforms to all applicable Federal Motor Vehicle Safety Standards [and Bumper and Theft Prevention Standards if applicable] in effect in (month, year).

2 SAFETY AND COMPLIANCE

Peterbilt Motors Company 2-3

However, if the vehicle cannot be completed and certified with in the guidance provided in the IVD, the final stage manufacturer must ensure the vehicle conforms to all applicable Federal Motor Vehicle Safety Standards (FMVSS). The final stage manufactures certification label would need a statement that reads, This vehicle conforms to all applicable Federal Motor Vehicle Safety Standards [and Bumper and Theft Prevention Standards if applicable] in effect in (month, year).These statements are just part of the changes to the new certification regulation. Please refer to the Feb 15, 2005 final rule for all of the details related to this regulation. You can contact NTEA Technical Services Department at 1-800- 441- NTEA for a copy of the final rule (DocID 101760).

For Canadian final stage manufacturers see:

http://www.gazette.gc.ca/index-eng.html; and http://www.tc.gc.ca/eng/acts-regulations/menu.htm for the regulations.

Or contact: Transport Canada Tower C, Place de Ville, 330 Sparks Street Ottawa, Ontario K1A 0N5 (613) 990-2309 TTY: 1-888-675-6863 Noise and Emissions Requirements

NOTE This truck may be equipped with specific emissions control components/systems* in order to meet applicable Federal and California noise and exhaust emissions requirements. Tampering with these emissions control components/systems* is against the rules that are established by the U.S Code of Federal Regulations, Environment Canada Regulations and California Air Resources Board (CARB). These emissions control components/systems* may only be replaced with original equipment parts.

Additionally, most vehicles in North America will be equipped with a Greenhouse Gas (GHG) Vehicle Emission Control Information door label indicating its certified configuration. The vehicle components listed on this label are considered emission control devices.

Modifying (i.e. altering, substituting, relocating) any of the emissions control components/systems defined above will affect the noise and emissions performance/certification. Modifications that alter the overall shape and aerodynamic performance of a tractor will also affect the emission certification. If modifications are required, they must first be approved by the manufacturer. Unapproved modifications could negatively affect emissions performance/certification. There is no guarantee that proposed modifications will be approved.

Tires may be substituted provided the new tires possess a Coefficient of rolling resistance (Crr) equal to or lower than Crr of the original tires. Consult with your tire supplier(s) for appropriate replacement tires.

Contact the engine manufacturer for any requirements and restrictions prior to any modifications.

For Cummins Contact 1-800-DIESELS or your local Cummins distributor. Reference AEB 21.102.

It is possible to relocate the DEF tank; however the relocation requirements need to be followed. Any variances from the relocation requirements may cause the emissions control components/systems to operate improperly potentially resulting in engine de-rate.

2 SAFETY AND COMPLIANCE

Peterbilt Motors Company 2-4

NOTE All 2017 engine emissions certified vehicles will be equipped with an On-Board Diagnostics (OBD) system. The OBD system is designed to detect malfunctions of any engine or vehicle component that may increase exhaust emissions or interfere with the proper performance of the OBD system itself All diesel engines will be equipped with an On-Board Diagnostics (OBD) system. The OBD system consists of computer program on one or more of the vehicles Electronic Control Units (ECUs). This program uses information from the control system and from additional sensors to detect malfunctions. When a malfunction is detected, information is stored in the ECU(s) for diagnostic purposes. A Malfunction Indicator Light (MIL) is illuminated in the dash to alert the driver of the need for service of an emission-related component or system.

To ensure compliance to emissions regulations, the final configuration of certain features of the completed vehicle must meet specific requirements. This section describes requirements relevant for only the most common or critical modifications done by body builders. For a complete description of acceptable modifications, see the application guidance available from the manufacturer of the engine installed in the chassis.

Fuel System The following are highlights of some of the more common or critical aspects of this system.

The overall system restriction may not exceed the restriction limitations set forth by the engine manufacturer for both supply and return.

Ensure that fuel lines are not pinched or can potentially be damaged when installed between body and frame

Fuel lines must be routed and secured without dips or sags

There must be easy access to filter(s) and fill cap

The tank vent may not obstructed

Added accessories (heaters, generators) cannot introduce air into system

Fuel tank must be located so that the full level is not above cylinder head

Ultra-Low Sulfur Fuel Only labels must be present on the dash and fuel fill

Modification of the pressure side secondary filter and plumbing is not allowed without engine manufacturer approval

Body installation of fuel tank or routing of lines must not cause significant increase in fuel temperature

Fuel hoses shall meet or exceed OEM supplied hose material construction specifications

Compressed Air System The following are highlights of some of the more common or critical aspects of this system.

Air system modification must meet applicable FMVSS regulations

Compressed Air tank may not be modified (exception addition or removal of fittings or relocation of the tank)

Added devices or bodywork may not interfere with or rub air lines

2 SAFETY AND COMPLIANCE

Peterbilt Motors Company 2-5

Air supply to the engine doser may not be restricted or disconnected

Air lines should be routed, protected from heat, and properly secured to prevent damage from other components

Care should be taken so that air lines do not rub against other components

Care should be taken to protect the air system from heat sources

Exhaust and Exhaust After-treatment System The following are highlights of some of the more common or critical aspects of this system.

The following after-treatment and exhaust system components may not be modified:

DPF assembly

SCR Catalyst assembly

Exhaust pipes between the engine and after-treatment devices (DPF, SCR Catalyst) and between after-treatment devices

NOx Sensors

PM Sensor

The following modifications may only be done within the guidelines of the DEF System Relocation Guide.

Modifications to Diesel Exhaust Fluid (DEF) throttle, suction, or pressure lines

Modification or relocation of the DEF tank

Modification of coolant lines to and from the DEF tank

All DEF and coolant lines should be routed, protected, and properly secured to prevent damage during vehicle operation or other components

The DPF/SCR catalyst or its mounting may not be modified

The NOx sensor may not be relocated or altered in any way; this includes re-clocking the aftertreatement canister or reorienting the sensor(s)

Exhaust pipes used for tailpipes/stacks must be properly sized, and must prevent water from entering

Ensure adequate clearance between the exhaust and body panels, hoses, and wire harnesses

The body in the vicinity of the DPF must be able to withstand temperatures up to 400C (750F)

Do not add thermal insulation to the external surface of the DPF

The SCR water drain hole may not be blocked

Allow adequate clearance (25mm (1 inch)) for servicing the DPF sensors, wiring, and clamped joints

Drainage may not come in contact with the DPF/SCR, sensors or wiring

2 SAFETY AND COMPLIANCE

Peterbilt Motors Company 2-6

Allow sufficient clearance for removing sensors from DPF. Thermistors require four inches. Other sensors require one inch

Wiring should be routed, protected from heat, and properly secured to prevent damage from other components

The exhaust system from an auxiliary power unit (APU) must not be connected to any part of the vehicle after-treatment system or vehicle tail pipe.

Cooling System The following are highlights of some of the more common or critical aspects of this system.

Modifications to the design or locations of fill or vent lines, heater or defroster core, and surge tank are not recommended

Additional accessories plumbed into the engine cooling system are not permitted, at the risk of voiding vehicle warranty

Coolant level sensor tampering will void warranty

When installing auxiliary equipment in front of the vehicle, or additional heat exchangers, ensure that adequate air flow is available to the vehicle cooling system. Refer to engine manufacturer application guidelines for further detail

When installing FEPTO drivelines, the lower radiator anti-recirculation seal must be retained with FEPTO driveline clearance modification only

Changes made to cooling fan circuit and controls are not allowed, with the exception of AC minimum fan on time parameter

See owners manual for appropriate winter front usage

Air Intake System The following are highlights of some of the more common or critical aspects of this system.

The air intake screen may not be blocked, either fully or partially

Modification to the air intake system may not restrict airflow. For example, pipe diameter may not be reduced

All sensors must be retained in existing locations

To retain system seal, proper clamp torque must be used. Refer to service manual for proper clamp torque

Charge Air Cooler System The following are highlights of some of the more common or critical aspects of this system.

The Charge Air Cooler may not be modified

The installation of engine overspeed shutdown devices must not introduce restriction in the intake system

All plumbing associated with the charge air cooler may not be modified

SECTION 3 DIMENSIONS INTRODUCTION This section has been designed to provide enough information to successfully layout a chassis in the body planning process. All dimensions are inches unless otherwise noted. Optional equipment may not be depicted. Please contact your local Peterbilt dealer if more dimensional information is desired.

ABBREVIATIONS Throughout this section and in other sections as well, abbreviations are used to describe certain characteristics on your vehicle. Table 3-1 below lists the abbreviated terms used.

TABLE 3-1. Abbreviations Used BFA Bumper to front axle

BOC Back of cab

CA Cab to axle. Measured from the back of the cab to the centerline of the rear axle(s).

EOF End of frame

FAX Front axle

FOF Front of frame

WB Wheelbase OVERALL DIMENSIONS This section includes drawings and charts of the Peterbilt Model 520. On the pages that follow, detail drawings show particular views of the vehicle; all dimensions are in inches (in). They illustrate important measurements critical to designing bodies of all types. See the Table of Contents at the beginning of the manual to locate the drawing that you need. All heights are given from the bottom of the frame rail. Peterbilt also offers .dxf files and frame layouts of ordered chassis prior to build. Please speak with your local dealership to request this feature when specifying your chassis.

3 DIMENSIONS

Peterbilt Motors Company 3- 2

FIGURE 3-1. Various Views of the Model 520

3 DIMENSIONS

Peterbilt Motors Company 3- 3

EXTERIOR DIMENSIONS

FIGURE 3-2. 520 Cab Dimensions

Notes:

1. Shown with optional HD Air intake Pre-Cleaner 2. Shown with optional front cab guard 3. Door dimension is 33.4W x 61H 4. Diesel truck shown, but Natural Gas has same BOC dimension for After-treatment.

3 DIMENSIONS

Peterbilt Motors Company 3- 4

EXTERIOR DIMENSIONS

FIGURE 3-3. 520 Overall Width Dimensions

Notes:

1. Shown with Velvac mirrors 2. West coast mirrors 111.8

3 DIMENSIONS

Peterbilt Motors Company 3- 5

INTERIOR DIMENSIONS

FIGURE 3-4. View Looking Through Cab to the Drivers Side (LH Steer)

3 DIMENSIONS

Peterbilt Motors Company 3- 6

INTERIOR DIMENSIONS

FIGURE 3-5. View Looking Through the Cab At The RH Drive Standup Version

3 DIMENSIONS

Peterbilt Motors Company 3- 7

INTERIOR DIMENSIONS

FIGURE 3-6. Top View of LH Steer Model

3 DIMENSIONS

Peterbilt Motors Company 3- 8

INTERIOR DIMENSIONS

FIGURE 3-7. Floor Dimensions for LH Floor

3 DIMENSIONS

Peterbilt Motors Company 3- 9

INTERIOR DIMENSIONS

FIGURE 3-8. Passenger Floor RH Stand Up

3 DIMENSIONS

Peterbilt Motors Company 3- 10

FRAME RAILS Frame rail configurations are shown in Figure 3-8. The under cab area of the 520 frame rails are splayed as shown in Figure 3-9. Frame height, flange and structural values can be found in the Body Mounting Section.

FIGURE 3-9. Frame Rail Configurations

NOTE: The outserted frame section does not extend through the rear suspension area. The outserted frame section does not extend through the splayed area.

3 DIMENSIONS

Peterbilt Motors Company 3- 11

FRAME RAILS

FIGURE 3-10. Model 520 Frame Rail

3 DIMENSIONS

Peterbilt Motors Company 3- 12

FRAME HEIGHT CHARTS

FIGURE 3-4. Frame Height

3 DIMENSIONS

Peterbilt Motors Company 3- 13

TABLE 3-2. Front Frame Height A 520

NOTES:

1) Omit spacer block standard. 2) 25mm spacer block standard and required. 3) Standard 3-1/2" drop axle heights shown, for 5" drop axles, subtract an additional 1-1/2". 4) Spacer blocks are used by Engineering to obtain level frame and are not options. 5) "A" dimension shown is to bottom of frame rail. Add frame rail height dimension for frame height.

3 DIMENSIONS

Peterbilt Motors Company 3- 14

REAR FRAME HEIGHTS "C"

TABLE 3-3. Single Drive Suspension Heights

Suspension Rating Version Light

Height Laden Height

LOW AIR LEAF 21,000 lbs. Standard 6.8 6.5

AIR TRAC 20,000 lbs. Standard 11.4 11.0 23,000 lbs. Standard 11.4 11.0

REYCO 79KB

20,000 lbs. Taper-leaf (3.38" saddle) 9.4 11.8

21,000 lbs. Taper-leaf (1.38" saddle) 7.4 9.8

23,000 lbs. Multi-leaf (1.38" saddle) 8.8 11.6

26,000 lbs. Multi-leaf (1.38" saddle) 9.2 11.8

28,000 lbs. Multi-leaf (1.38" saddle) 9.6 12.3

31,000 lbs. Multi-leaf (1.38" saddle) 10.7 13.3

REYCO 102

23K-29K lbs. 4.38 saddle 12.0 10.2 23K-29K lbs. 4.63 saddle 12.2 10.4 29,000 lbs. 3.50 saddle 11.7 10.0 31,000 lbs. 3.50 saddle 12.2 10.5 31,000 lbs. 4.38 saddle 12.5 10.7 31,000 lbs. 4.63 saddle 12.7 10.9

REYCO 102AR (AIR) 17K -23K Standard 9.3 9.3 Low 8.3 8.3

3 DIMENSIONS

Peterbilt Motors Company 3- 15

TABLE 3-4. Tandem Drive Peterbilt Suspension Heights

Suspension Rating Version Light

Height Laden Height

AIR LEAF 38,000 lbs. 12.0 11.7 LOW AIR LEAF 40,000 lbs. 8.8 8.5 FLEX AIR 38,000 lbs. 8.8 8.5 LOW-LOW AIR LEAF 40,000 lbs. 6.8 6.5

AIR TRAC 40K-46K lbs. 11.4 11.0 QUADRAFLEX 38,000 lbs. Taper-leaf 10.6 8.7

TABLE 3-5. Tandem Drive Neway Suspension Heights

Suspension Rating Version Light

Height Laden Height

NEWAY AD 52,000 lbs. 10.0 10.0 NEWAY ADZ 46K-52K lbs. 10.0 10.0

TABLE 3-6. Tandem Drive Reyco Suspension Heights

Suspension Rating Version Light

Height Laden Height

REYCO 102 MULTILEAF

40,000 lbs. 1.75 saddle (STD) 11.7 9.8 1.38 saddle 10.2 8.3 3.38 saddle 13.4 11.5

44,000 lbs. 1.75 saddle (STD) 11.7 9.8 1.38 saddle 11.5 9.7

REYCO 102AR (AIR) 34K-40K STD LOW 8.3 8.3

3 DIMENSIONS

Peterbilt Motors Company 3- 16

TABLE 3-7. Tandem Drive Chalmers Suspension Heights

Suspension Rating Version Light

Height Laden Height

CHALMERS 854 & 860 40,000 lbs.

LOW 11.1 8.9 HIGH 12.4 10.2 X-HIGH 14.5 12.2 XX-HIGH 17.2 14.9

CHALMERS 854 & 860 46,000 lbs.

LOW 11.3 8.9 HIGH 12.5 10.1 X-HIGH 14.7 12.2 XX-HIGH 17.3 14.9

CHALMERS 854 & 860 50K-52K

LOW 11.3 8.9 HIGH 12.5 10.1 X-HIGH 14.6 12.1 XX-HIGH 17.3 14.8

CHALMERS 872 46,000 lbs.

LOW 11.2 8.8 HIGH 12.5 10.3 X-HIGH 14.6 12.2 XX-HIGH 17.3 14.9

CHALMERS 872 50,000 lbs.

LOW 11.2 8.8 HIGH 12.5 10.3 X-HIGH 14.6 12.1 XX-HIGH 17.3 14.8

NOTES: 1) Laden dimension shown with standard restrictor cans. Add 0.7 for #29 High Stability Restrictor Cans.

3 DIMENSIONS

Peterbilt Motors Company 3- 17

TABLE 3-8. Tandem Drive Hendrickson Suspension Heights

Suspension Rating Version Light

Height Laden Height

RT-403 40,000 lbs. 6.00 9.9 8.9 7.188 (std.) 11.2 10.1

RTE-403 40,000 lbs. 6.00 9.9 8.4 7.188 (std.) 11.2 9.5

R-403 40,000 lbs. 12.80 5.8 5.8 15.81 (std.) 8.8 8.8 17.60 10.6 10.6

RS-403 40,000 lbs. 12.25 9.9 9.1 14.00 (std.) 11.7 10.8 15.25 12.9 12.1

HMX 40,000 lbs. 16.5 (low) 10.6 9.5 18.5 (std.) 12.6 11.5

HMX 46,000 lbs. 16.5 (low) 10.6 9.5 18.5 (std.) 12.6 11.5

HMX EX

40,000 lbs 16.5 11.6 9.5 17.5 12.6 10.5 18.5 (std.) 13.6 11.5

46,000 lbs 16.5 11.6 9.5 17.5 12.6 10.5 18.5 (std.) 13.6 11.5

52,000 lbs 18.5 13.6 11.5 HN462 46,000 lbs. 20.25 (high) 15.0 13.3

R-463 46,000 lbs. 15.75 (std.) 8.8 8.8 20.50 13.5 13.5

RS-463 46,000 lbs. 12.25 9.7 8.9 14.0 (std.) 11.5 10.6 15.25 12.7 11.9

RT-463 46,000 lbs. 6.00 11.3 10.5 7.188 (std.) 13.0 11.4 11.00 16.3 15.2

RTE-463 46,000 lbs. 7.188 (std.) 11.6 10.2 11.00 15.4 14.0

RS-503 50,000 lbs. 14.0 (std.) 11.7 10.8 15.25 12.9 12.1

RT-503 50,000 lbs. 7.188 (std.) 12.1 11.1 11.0 1 16.4 15.4

RTE-503 50,000 lbs. 7.188 (std.) 11.6 10.2 11.00 15.4 14.0

NOTES: 1) With SISU 70k axle subtract 0.39 from light/laden 2) With SISU 70k axle subtract 0.28 from light and 0.39 from laden

3 DIMENSIONS

Peterbilt Motors Company 3- 18

TABLE 3-8 (cont). Tandem Drive Hendrickson Suspension Heights

RS-523 52,000 lbs. 14.0 (std.) 11.7 10.8

RT-523 , RT-650 52K-65K 7.188 (std.) 12.1 11.1 11.00 16.4 15.4

HN522 52,000 lbs. 18.50 (std.) 12.6 11.5

RS650 65,000 lbs. 15.00 (std.) 12.0 1 11.0 2 19.00 16.0 2 15.1 2

R650 * 65,000 lbs. 20.25 (std.) 12.5 12.5 R850 w/70K Meritor 85,000 lbs. 20.25 12.0 12.0 R850 w/SISU 70K 20.25 12.1 12.1 RS850 w/SISU 70K 85,000 lbs. 16.75 11.5 10.6

TABLE 3-9. Tri-Drive Suspension Heights

SUSPENSION RATING (lbs.) LIGHT (in.) LOADED

(in.) TRI-DRIVE SUSPENSION AIR TRAC 40K-46K 11.4 11.0 NEWAY ADZ369 69,000 10.0 10.0 NEWAY ADZ378 78,000 10.0 10.0

3 DIMENSIONS

Peterbilt Motors Company 3- 19

REAR SUSPENSION LAYOUTS The rear suspension layouts are provided as a tool to help layout bodies prior to arrival. The applicable dimensions are shown. Verify the axle spacing that is shown, as alternate spacing may exist and could change some of the dimensions. The dimensions shown below are the most typical installations, in special cases some hole locations will move. If the holes shown will be used for body installation, please confirm with the local Peterbilt dealer the drawing below will be the installation used on the specific truck. In this case, ordering the frame layout of the chassis is advised. This can be done on any Peterbilt truck, and will be provided ahead of the build schedule. Ensure proper torque to reinstall any suspension components. See Tables 5-1 and 5-2 on page 5-4. For hole locations not detailed, please work with the local Peterbilt Dealer to request that information.

3 DIMENSIONS

Peterbilt Motors Company 3- 20

FIGURE 3-5. Reyco 79KB Frame Drilling (Dimensions In Inches)

3 DIMENSIONS

Peterbilt Motors Company 3- 21

FIGURE 3-6. Reyco 102AR Frame Drilling (Dimensions In Millimeters)

3 DIMENSIONS

Peterbilt Motors Company 3- 22

FIGURE 3-7. Neway ADZ 252 Frame Drilling (Dimensions In Inches)

3 DIMENSIONS

Peterbilt Motors Company 3- 23

FIGURE 3-8. Neway ADZ 369/378 Frame Drilling (Dimensions In Inches)

3 DIMENSIONS

Peterbilt Motors Company 3- 24

FIGURE 3-9. Peterbilt Air Leaf Tandem Frame Drilling (Dimensions In Millimeters)

3 DIMENSIONS

Peterbilt Motors Company 3- 25

FIGURE 3-10. Peterbilt Air Trac Single Frame Drilling (Dimensions In Millimeters)

3 DIMENSIONS

Peterbilt Motors Company 3- 26

FIGURE 3-11. Peterbilt Air Trac Tandem Frame Drilling (Dimensions In Millimeters)

3 DIMENSIONS

Peterbilt Motors Company 3- 27

FIGURE 3-12. Peterbilt Air Trac Tri-Drive Frame Drilling (Dimensions In Millimeters)

3 DIMENSIONS

Peterbilt Motors Company 3- 28

FIGURE 3-13. Peterbilt Low and Low-Low Air Leaf Tandem Frame Drilling (Dimensions In Millimeters)

3 DIMENSIONS

Peterbilt Motors Company 3- 29

FIGURE 3-14. Chalmers 854 Tandem Frame Drilling

3 DIMENSIONS

Peterbilt Motors Company 3- 30

FIGURE 3-15. Hendrickson HMX Tandem Frame Drilling

3 DIMENSIONS

Peterbilt Motors Company 3- 31

FIGURE 3-16. Hendrickson RT/RTE Tandem Frame Drilling

3 DIMENSIONS

Peterbilt Motors Company 3- 32

FIGURE 3-17. Hendrickson HN Tandem Frame Drilling (Dimensions In Millimeters)

3 DIMENSIONS

Peterbilt Motors Company 3- 33

FIGURE 3-18. Hendrickson R Tandem Frame Drilling (Dimensions In Millimeters)

3 DIMENSIONS

Peterbilt Motors Company 3- 34

FIGURE 3-19. Hendrickson RS Tandem Frame Drilling (Dimensions In Millimeters)

3 DIMENSIONS

Peterbilt Motors Company 3- 35

PUSHER AND TAG AXLE LAYOUTS The rear pusher axle layouts are provided as a tool to help layout bodies prior to arrival. The applicable dimensions are shown. When using the pusher layouts to determine available frame space please be aware clearances required are not shown. For information that may not be detailed in these drawings, work with your local Peterbilt Dealer to request that information.

FIGURE 3-20. Hendrickson SC8, SC10, SC13, SCO13, FX or FXO Pusher or Tag

3 DIMENSIONS

Peterbilt Motors Company 3- 36

FIGURE 3-21. Hendrickson SC20 Pusher or Tag

3 DIMENSIONS

Peterbilt Motors Company 3- 37

FIGURE 3-22. Hendrickson HLR2 Pusher

3 DIMENSIONS

Peterbilt Motors Company 3- 38

FIGURE 3-23. Hendrickson HLM Pusher or Tag

3 DIMENSIONS

Peterbilt Motors Company 3- 39

FIGURE 3-24. Watson-Chalin SL2065 Pusher or Tag

3 DIMENSIONS

Peterbilt Motors Company 3- 40

FIGURE 3-25. Watson-Chalin AL2200 Pusher or Tag

3 DIMENSIONS

Peterbilt Motors Company 3- 41

FIGURE 3-26. Watson-Chalin SL0893SSR or SL1093SSR Pusher or Tag

3 DIMENSIONS

Peterbilt Motors Company 3- 42

FIGURE 3-27. Watson-Chalin SL1190SSR Pusher or Tag

3 DIMENSIONS

Peterbilt Motors Company 3- 43

EXHAUST HEIGHT CALCULATIONS

The exhaust height calculations are provided as a tool to help layout bodies prior to arrival as well as aid in exhaust configuration selection. Please work with the local Peterbilt Dealer to request additional information if required. The overall exhaust height (EH) can be estimated based on the following formula: EH = Y + SPL + (A + B + C + D) / 2

TABLE 3-10. Exhaust Heights

Y Dimension

Exhaust Location

ISLG ISLG Near Zero

MX-11 PX-9 HHP PX-9 MHP

BOC Vertical 74.2 80.5 84.4 81.2 79.7

NOTES: 1) For A and C values, reference the FRAME HEIGHTS section for front or rear suspension height. 2) For B and D values, reference the tire manufacturers website or catalog for static loaded radius (SLR). 3) For Stand Pipe Length (SPL) values, reference the truck sales order. 4) Not applicable to horizontal exhaust.

FIGURE 3-27. Exhaust Height Calculations

3 DIMENSIONS

Peterbilt Motors Company 3- 44

GROUND CLEARANCE CALCULATIONS The ground clearance tables are provided as a tool to help layout bodies prior to arrival, not all optional equipment is included. The ground clearance (GC) can be estimated based on the following formula: GC = (A + B + C + D) / 2 - Y TABLE 3-11. Ground Clearance

FIGURE 3-28. Ground Clearance Calculations

FIGURE 3-29. Space Saver Battery Box NOTES: 1) For A and C values, reference the FRAME HEIGHTS section for front suspension height or rear suspension

height. 2) For B and D values, reference the tire manufacturers website or catalog for overall diameter or static loaded

radius (SLR).

Y = DISTANCE FROM BOTTOM OF FRAME TO BOTTOM OF COMPONENT

Component Y Cab Access Step 14.7

Alum Space Saver (Shown Below) 10.0

Steel Space Saver Battery Box 11.8

Narrow Space Saver Battery Box 11.9

Fender Mounted Battery Box 4.4

20" Diameter Fuel Tank 12.4

23" Diameter Fuel Tank 15.2

26" Diameter Fuel Tank 18.0

3 DIMENSIONS

Peterbilt Motors Company 3- 45

OVERALL CAB HEIGHT CALCULATIONS

The overall cab height tables are provided as a tool to help layout bodies prior to arrival, no roof mounted equipment is included. The overall cab height (CH) can be estimated based on the following formula: CH = (A + B + C + D) / 2 + 73.2

NOTES: 1) For A and C values, reference the FRAME HEIGHTS section for front suspension height or rear suspension

height. 2) For B and D values, reference the tire manufacturers website or catalog for overall diameter or static loaded

radius (SLR). 3) Roof mounted content such as horns and antennas are not included.

FIGURE 3-30. Overall Cab Height Calculations

3 DIMENSIONS

Peterbilt Motors Company 3- 46

FRAME COMPONENTS

This section includes drawings and charts related to common frame mounted components. Optional equipment may not be depicted. Please work with the local Peterbilt Dealer to request additional information if required. At the dealers request, Peterbilt can provide frame layouts for individual vehicles prior to delivery. FUEL TANKS

FIGURE 3-31. Fuel Tanks TABLE 3-12. Fuel Tank Dimensions

DIMENSIONS A B C D

20" TANK 22.7 12.4 10.3 27.5

23" TANK 24.5 15.2 10.5 31.0

26" TANK 27.2 18.0 10.6 33.7

TABLE 3-13. Fuel Tank Data

GALLONS TANK LENGTH USEABLE TOTAL 20" 23" 26"

40 46 33.3 N/A N/A 50 57 43.2 34.5 26.7 60 67 51.3 40.7 31.5 70 78 57.3 46.8 36.2 80 89 65.3 52.9 41.0 90 99 N/A 59.0 45.7 100 110 N/A *65.1 50.5 110 121 N/A N/A 55.2 120 131 N/A 77.3 60.0 135 147 N/A N/A 66.8 150 163 N/A N/A *74.0 NOTES: 1) * Largest capacity without a weld seam

SECTION 4 BODY MOUNTING INTRODUCTION

This section has been designed to provide guidelines to aid in body mounting. This is not intended as a complete guide, rather as general information. Body mounting strategies are unique to each body type, and body builders must determine the appropriate method. Please contact your local Peterbilt dealer if more information is desired. FRAME RAILS

Frame rail information is provided in Table 4-1 and Table 4-2. TABLE 4-1. Single Frame Rails

Rail Height (in.)

Flange Width (in.)

Web Thickness (in)

Section Modulus (cu. In.)

RBM (per rail) (in.-lbs)

Weight (per rail) (lbs/in.)

10 3/4 3.50 0.375 17.8 2,136,000 1.74 TABLE 4-2. Built-up Frame Rails

Main Rail Height

(in.) Insert Outsert

Section Modulus (cu. In.)

RBM (per rail) (in.-lbs)

Weight (per rail) (lbs/in.)

10 3/4 9.875 x 2.87 x .250 None 28.9 3,468,000 2.78 10 3/4 9.875 x 2.87 x .250 11.63 x 3.87 x .375 45.7 5,484,000 4.67(1)

(1)Weight per inch in the outserted area only. (Outsert starts behind the rear front spring hanger)

4 BODY MOUNTING

Peterbilt Motors Company 4-2

CRITICAL CLEARANCES REAR TIRES AND CAB

CAUTION: Insufficient clearance between rear tires and body structure could cause damage to the body during suspension movement.

Normal suspension movement could cause contact between the tires and the body. To prevent this, mount the body so that the minimum clearance between the top of the tire and the bottom of the body is 8 inches (203 mm). This should be measured with the body empty. See Figure 4-1.

FIGURE 4-1. Minimum Clearance Between Top of Rear Tires and Body Structure Overhang

CAUTION: Maintain adequate clearance between back of cab and the front (leading edge) of mounted body. It is recommended the body leading edge be mounted 4 in. behind the cab. See Figure 4-2. NOTE: Be sure to provide access to all maintenance and service components.

FIGURE 4-2. Minimum Back of Cab Clearance

4 BODY MOUNTING

Peterbilt Motors Company 4-3

BODY MOUNTING USING BRACKETS

CAUTION: Always install a spacer between the body subframe and the top flange of the frame rail. Installation of a spacer between the body subframe and the top flange of the frame rail will help prevent premature wear of the components due to chafing or corrosion.

WARNING! When mounting a body to the chassis, DO NOT drill holes in the upper or lower flange of the frame rail. If the frame rail flanges are modified or damaged, the rail could fail prematurely and cause an accident. Mount the body using body mounting brackets or Ubolts.

FRAME SILL If the body is mounted to the frame with brackets, we recommend a frame sill spacer made from a strip of rubber or plastic (delrin or nylon). These materials will not undergo large dimensional changes during periods of high or low humidity. The strip will be less likely to fall out during extreme relative motion between body and chassis. See Figure 4-3.

FIGURE 4-3. Spacer Between Frame Sill and Body Rail Rubber or Plastic

4 BODY MOUNTING

Peterbilt Motors Company 4-4

BRACKETS

When mounting a body to the chassis with brackets, we recommend designs that offer limited relative movement, bolted securely but not too rigid. Brackets should allow for slight movement between the body and the chassis. For instance, Figure 4-4 shows a high compression spring between the bolt and the bracket, and Figure 4-5 shows a rubber spacer between the brackets. These designs will allow relative movement between the body and the chassis during extreme frame racking situations. Mountings that are too rigid could cause damage to the body. This is particularly true with tanker installations.

FIGURE 4-4. Mounting Brackets FIGURE 4-5. Mounting Brackets

4 BODY MOUNTING

Peterbilt Motors Company 4-5

MOUNTING HOLES

When installing brackets on the frame rails, the mounting holes in the chassis frame bracket and frame rail must comply with the general spacing and location guidelines illustrated in Figure 4-6.

FIGURE 4-6. Hole Location Guidelines for Frame Rail and Bracket

FIGURE 4-7. Crossmember Gusset Hole Patterns (Additional Holes Available in 50 mm Horizontal Increments)

4 BODY MOUNTING

Peterbilt Motors Company 4-6

FRAME DRILLING

WARNING! When mounting a body to the chassis, DO NOT drill holes in the upper or lower flange of the frame rail. If the frame rail flanges are modified or damaged, the rail could fail prematurely and cause an accident. Mount the body using body mounting brackets or Ubolts.

FIGURE 4-8. Frame Rail Flange Drilling Prohibited

WARNING! DO NOT drill closely spaced holes in the frame rail. Frame hole centers of two adjacent holes should be spaced no less than twice the diameter of the largest hole. Closer spacing could induce a failure between the two holes.

CAUTION: An appropriately sized bolt and nut must be installed and torqued properly in all unused frame holes. Failure to do so could result in a frame crack initiation around the hole.

CAUTION: Use care when drilling the frame web so the wires and air lines routed inside the rail are not damaged. Failure to do so could cause an inoperable electrical or air system circuit.

CAUTION: Never use a torch to make holes in the rail. Use the appropriate diameter drill bit. Heat from a torch will affect the material properties of the frame rail and could result in frame rail cracks.

CAUTION: The frame hole diameter should not exceed the bolt diameter by more than 0.060 inches (1.5mm).

4 BODY MOUNTING

Peterbilt Motors Company 4-7

BODY MOUNTING USING UBOLTS If the body is mounted to the frame with Ubolts, use a hardwood sill (minimum 1/2 inch thick) between the frame rail and body frame to protect the top surface of the rail flange.

WARNING! Do not allow the frame rails or flanges to deform when tightening the Ubolts. It will weaken the frame and could cause an accident. Use suitable spacers made of steel or hardwood on the inside of the frame rail to prevent collapse of the frame flanges.

Use a hardwood spacer between the bottom flange and the Ubolt to prevent the Ubolt from notching the frame flange. See Figure 4-9.

FIGURE 4-9. Acceptable U-Bolt Mounting with Wood and Fabricated Spacers

4 BODY MOUNTING

Peterbilt Motors Company 4-8

WARNING! Do not allow spacers and other body mounting parts to interfere with brake lines, fuel lines, or wiring harnesses routed inside the frame rail. Crimped or damaged brake lines, fuel lines, or wiring could result in loss of braking, fuel leaks, electrical overload or a fire. Carefully inspect the installation to ensure adequate

clearances for air brake lines, fuel lines, and wiring. See Figure 4-10.

FIGURE 4-10. Clearance Space for Air Lines and Cables

WARNING! Do not notch frame rail flanges to force a Ubolt fit. Notched or damaged frame flanges could result in premature frame failure. Use a larger size U-bolt.

CAUTION: Mount Ubolts so they do not chafe on frame rail, air or electric lines.

4 BODY MOUNTING

Peterbilt Motors Company 4-9

REAR BODY MOUNT When Ubolts are used to mount a body we recommend that the last body attachment be made with a fishplate bracket. See Figure 4-11. This provides a firm attaching point and helps prevent any relative fore or aft movement between the body and frame. For hole location guidelines, See Figure 4-6.

FIGURE 4-11. Fishplate Bracket at Rear End of Body

This page is intentionally left blank.

SECTION 5 FRAME MODIFICATIONS INTRODUCTION Peterbilt offers customer specified wheelbases and frame overhangs. So, in most cases frame modifications should not be necessary. However, some body installations may require slight modifications, while other installations will require extensive modifications. Sometimes an existing dealer stock chassis may need to have the wheelbase changed to better fit a customers application. The modifications may be as simple as modifying the frame cutoff, or as complex as modifying the wheelbase. DRILLING RAILS If frame holes need to be drilled in the rail, see SECTION 4 BODY MOUNTING for more information. MODIFYING FRAME LENGTH The frame overhang after the rear axle can be shortened to match a particular body length. Using a torch is acceptable; however, heat from a torch will affect the material characteristics of the frame rail. The affected material will normally be confined to within 1 to 2 inches (25 to 50mm) of the flame cut and may not adversely affect the strength of the chassis or body installation. CHANGING WHEELBASE Changing a chassis wheelbase is not recommended. Occasionally, however, a chassis wheelbase will need to be shortened or lengthened. Before this is done there are a few guidelines that should to be considered.

WARNING! When changing the wheelbase, be sure to follow the driveline manufacturers recommendations for driveline length or angle changes. Incorrectly modified drivelines can fail prematurely due to excessive vibration. This can cause an accident and severe personal injury.

WARNING! When changing the wheelbase, contact your local Peterbilt dealership for support. It is important to verify that these changes do not compromise vehicle frame strength.

Before changing the wheelbase, the driveline angles of the proposed wheelbase need to be examined to ensure no harmful vibrations are created. Consult with the driveline manufacturer for appropriate recommendations. Before the rear suspension is relocated, check the new location of the spring hanger brackets. The new holes for the spring hanger brackets must not overlap existing holes and should adhere to the guidelines in the FRAME DRILLING section of this manual. When shortening the wheelbase, the suspension should be moved forward and relocated on the original rail. The rail behind the suspension can then be cut to achieve the desired frame overhang. See Figure 5-1.

5 FRAME MODIFICATIONS

Peterbilt Motors Company 5-2

FIGURE 5-1. Wheelbase Customization

5 FRAME MODIFICATIONS

Peterbilt Motors Company 5-3

CROSSMEMBERS

After lengthening a wheelbase, an additional crossmember may be required to maintain the original frame strength. Con- tact Dealer for crossmember locations.

The maximum allowable distance between the forward suspension crossmember and the next crossmember forward is 47.2 inches (1200 mm). If the distance exceeds 47.2 inches (1200 mm) after the wheelbase is lengthened, add a crossmember between them. See Figure 5-2. See Figure 4-7 on page 4-5 for crossmember hole patterns.

FIGURE 5-2. Crossmember Spacing Requirements

5 FRAME MODIFICATIONS

Peterbilt Motors Company 5-4

TORQUE REQUIREMENTS

Torque values apply to fasteners with clean threads, lightly lubricated, with hardened steel washers, and nylon-insert nuts.

TABLE 5-1. Customary Grade 8 UNF or UNC.

Fastener Torque Size Nm lb-ft 5/16 2734 2025 3/8 4760 3544 7/16 7696 5671 1/2 117148 86109 9/16 167214 123-158 5/8 235296 173218 3/4 411523 303386 7/8 654846 482624 1 9731268 718935

TABLE 5-2. U.S. Customary - Grade 8 Metric Class 10.9

Fastener Torque Size Nm lb-ft M6 911 78 M8 2427 1820 M10 4754 3540 M12 8395 6170 M14 132150 97111 M16 206235 152173 M20 403458 297338

WELDING

The frame rails are heat treated and should not be welded. The high heat of welding nullifies the special heat treatment of the rails, greatly reducing the tensile strength of the frame rail. If a frame member becomes cracked from overloading, fatigue, surface damage or a collision, the only permanent repair is to replace the damaged frame member with a new part. The following information is provided for temporary emergency repair. Prior to welding a cracked frame rail, the area should be beveled (Vd out) to allow for a better weld. To prevent spreading of the crack, a 7 to 9 mm (1/4 in. to 3/8 in.) dia. hole should be drilled at the end of the crack. Widen the crack along its full length by using two hack saw blades together. When welding steel frames use the shielded arc method. Be sure to obtain full weld penetration along the entire length of the crack.

5 FRAME MODIFICATIONS

Peterbilt Motors Company 5-5

PRECAUTIONS

CAUTION: Before welding, disconnect the alternator terminals. Failure to do so could result in

damage to the voltage regulator and/or alternator.

CAUTION: To prevent damage to electrical equipment, disconnect battery cables before arc-welding on a truck, and be sure that the welding ground lead is connected to the frame. Bearings and other parts will be damaged if current must pass through them in order to complete the circuit.

WELDING PRECAUTIONS: ALL ELECTRONIC ENGINES

Before welding on vehicles with electronic engines, the following precautions should be observed.

1. Disconnect all electrical connections to the vehicle batteries.

2. Disconnect all ECM, TCM and VECU connectors.

3. Do no use the ECM, TCM, VECU or engine ground stud for the ground of the welding probe.

4. Ensure that the ground connection for the welder is as close to the weld point as possible. This ensures maximum weld current and minimum risk to damage electrical components on the vehicle.

5. Turn off key.

NOTE: Bendix ABS and Wabco ABS: Disconnect ECU, TCM & VECU.

This page is intentionally left blank.

SECTION 6 CAN COMMUNICATIONS INTRODUCTION Controller Area Network (CAN) is a serial network technology that was originally designed for the automotive industry but has also become popular in the commercial trucking industry. The CAN bus is primarily used in the embedded systems and network technology that provides fast communication among controllers up to real-time requirements, eliminating the need for the much more expensive and complex technology. CAN is a two-wire high-speed network system, that is far superior to conventional hardwired technologies functionality and reliability. CAN implementations are more cost effective. CAN is designed for real-time requirements which can easily beat hardwire connections when it comes to short reaction times, timely error detection, quick error recovery, and error repair. Characteristics of the Controller Area Network

A serial networking technology for embedded solutions Needs only two wires to communicate messages Operates at data rates of 250K and 500K Supports a maximum of 8 bytes per message frame One application can support multiple message IDs Supports message priority, i.e. the lower the message ID the higher its priority

CAN COMMUNICATIONS ACRONYM LIBRARY

Acronym Definition CAN Controller Area Network J-1939 SAE CAN Communication Standard PGN Parameter Group Number PTO Power Take Off SPN Suspect Parameter Number

SCR Selective Catalytic Reduction DPF Diesel Particulate Filter Regen Aftertreatment Regeneration TSC1 Torque Speed Commands

CAN Communications

Peterbilt Motors Company 6-2

6 SAE J1939 The Society of Automotive Engineers (SAE) Communications Subcommittee for Truck and Bus Controls has developed a family of standards concerning the design and use of devices that transmit electronic signals and control information among vehicle components. SAE J1939 and its companion documents are the accepted industry standard for the vehicle network of choice for commercial truck applications. SAE J1939 is used in the commercial vehicle area for communication in the embedded systems of the commercial vehicle. SAE J1939 uses CAN as physical layer. It is a recommended practice that defines which and how the data is communicated between the Electronic Control Units within a vehicle network. Typical controllers are the Engine, Brake, Transmission, etc. The messages exchanged between these units can be data such as vehicle road speed, torque control message from the transmission to the engine, oil temperature, and many more. Characteristics of J1939

Extended CAN identifier (29 bit) Peer-to-peer and broadcast communication Network management Definition of parameter groups for commercial vehicles and others Manufacturer specific parameter groups are supported Diagnostics features A standard developed by the Society of Automotive Engineers Defines communication for vehicle networks A Higher-Layer Protocol using CAN as the physical layer Uses unshielded twisted pair wire Applies a maximum network length of 120 ft. Applies a standard baud rate of 500 Kbit/sec Supports peer-to-peer and broadcast communication Supports message lengths up to 1785 bytes Defines a set of Parameter Group Numbers Supports network management

PARAMETER GROUP NUMBER Parameter Groups contain information on parameter assignments within the 8-byte CAN data field of each message as well as repetition rate and priority. Parameters groups are, for instance, engine temperature, which includes coolant temperature, fuel temperature, oil temperature, etc. Parameter Groups and their numbers are listed in SAE J1939 and defined in SAE J1939/71, a document containing parameter group definitions plus suspect parameter numbers. SUSPECT PARAMETER NUMBER A Suspect Parameter Number is a number assigned by the SAE to a specific parameter within a parameter group. It describes the parameter in detail by providing the following information: Data Length in bytes Data Type Resolution Offset Range Reference Tag (Label) SPNs that share common characteristics are grouped into Parameter Groups, and they will be transmitted throughout the network using the Parameter Group Number.

CAN Communications

Peterbilt Motors Company 6-3

6 CAN MESSAGES AVAILABLE ON BODY CONNECTIONS

SPN CAN Signal Name PGN, Message Tx SA Rx SA CAN Bus 38 Fuel Level 2 65276, DD1 39 Broadcast KCAN, SCAN, BCAN 46 Pneumatic Supply Pressure 65198, AIR1 48 Broadcast KCAN, SCAN, BCAN 51 Engine Throttle Valve 1 Position 1 65266, LFE1 00 Broadcast KCAN, SCAN, BCAN 52 Engine Intercooler Temperature 65262, ET1 00 Broadcast KCAN, SCAN, BCAN 69 Two Speed Axle Switch 65265, CCVS1 00 Broadcast KCAN, SCAN, BCAN 70 Parking Brake Switch 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 74 Maximum Vehicle Speed Limit 65261, CCSS 39 Broadcast KCAN, SCAN

81 Aftertreatment 1 Diesel Particulate Filter Intake Pressure

65270, IC1 00 Broadcast KCAN,SCAN,BCAN

84 Wheel-Based Vehicle Speed 65265, CCVS1 00 Broadcast KCAN, SCAN, BCAN 86 Cruise Control Set Speed 65265, CCVS1 00 Broadcast KCAN, SCAN, BCAN 86 Cruise Control Set Speed 65265, CCVS1 39 Broadcast KCAN, SCAN 90 Power Takeoff Oil Temperature 65264, PTO 7, 33 Broadcast KCAN, SCAN, BCAN 91 Accelerator Pedal Position 1 61443, EEC2 00 Broadcast KCAN, SCAN, BCAN 92 Engine Percent Load At Current Speed 61443, EEC2 00 Broadcast KCAN, SCAN, BCAN 94 Engine Fuel Delivery Pressure 65263, EFL/P1 00 Broadcast KCAN, SCAN, BCAN 96 Fuel Level 1 65276, DD1 39 Broadcast KCAN, SCAN, BCAN 97 Water In Fuel Indicator 1 65279, OI 00 Broadcast KCAN, SCAN, BCAN 98 Engine Oil Level 65263, EFLP1 00 Broadcast KCAN, SCAN,BCAN

100 Engine Oil Pressure 1 65263, EFL/P1 00 Broadcast KCAN, SCAN, BCAN 101 Engine Crankcase Pressure 1 65263, EFL/P1 00 Broadcast KCAN, SCAN, BCAN 102 Engine Intake Manifold #1 Pressure 65270, IC1 00 Broadcast KCAN, SCAN, BCAN 105 Engine Intake Manifold 1 Temperature 65270, IC1 00 Broadcast KCAN, SCAN, BCAN 106 Engine Intake Air Pressure 65270, IC1 00 Broadcast KCAN, SCAN, BCAN 108 Barometric Pressure 65269, AMB 00 Broadcast KCAN, SCAN, BCAN 110 Engine Coolant Temperature 65262, ET1 00 Broadcast KCAN, SCAN, BCAN 111 Engine Coolant Level 1 65263, EFL/P1 00 Broadcast KCAN, SCAN, BCAN 117 Brake Primary Pressure 65274, B1 39 Broadcast KCAN, SCAN, BCAN 118 Brake Secondary Pressure 65274, B1 39 Broadcast KCAN, SCAN, BCAN 158 Key Switch Battery Potential 65271, VEP1 39 Broadcast KCAN, SCAN 161 Transmission 1 Input Shaft Speed 61442, ETC1 03 Broadcast KCAN, SCAN, BCAN 162 Transmission Requested Range 61445, ETC2 03 Broadcast KCAN, SCAN, BCAN 163 Transmission Current Range 61445, ETC2 03 Broadcast KCAN, SCAN, BCAN 168 Battery Potential / Power Input 1 65271, VEP1 39 Broadcast KCAN, SCAN, BCAN 168 Battery Potential / Power Input 1 65271, VEP1 00 Broadcast KCAN, SCAN, BCAN 171 Ambient Air Temperature 65269, AMB 00 Broadcast KCAN, SCAN, BCAN 173 Engine Exhaust Temperature 65270, IC1 00 Broadcast KCAN, SCAN, BCAN 174 Engine Fuel Temperature 1 65262, ET1 00 Broadcast KCAN, SCAN, BCAN 175 Engine Oil Temperature 1 65262, ET1 00 Broadcast KCAN, SCAN, BCAN

CAN Communications

Peterbilt Motors Company 6-4

6 177 Transmission Oil Temperature 1 65272, TRF1 03 Broadcast KCAN, SCAN, BCAN 182 Engine Trip Fuel 65257, LFC1 00 Broadcast KCAN, SCAN, BCAN 183 Engine Fuel Rate 65266, LFE1 00 Broadcast KCAN, SCAN, BCAN 184 Engine Instantaneous Fuel Economy 65266, LFE1 00 Broadcast KCAN, SCAN, BCAN 185 Engine Average Fuel Economy 65266, LFE1 23 Broadcast KCAN, SCAN, BCAN 187 Power Takeoff Set Speed 65264, PTO 39 Broadcast KCAN, SCAN, BCAN 187 Power Take Off Set Speed 65264, PTO 00 Broadcast KCAN, SCAN, BCAN 190 Engine Speed 61444, EEC1 00 Broadcast KCAN, SCAN, BCAN 191 Transmission 1 Output Shaft Speed 61442, ETC1 03 Broadcast KCAN, SCAN, BCAN 235 Engine Total Idle Hours 65244, IO 00 Broadcast KCAN, SCAN, BCAN 236 Engine Total Idle Fuel Used 65244, IO 00 Broadcast KCAN, SCAN, BCAN 237 Vehicle Identification Number 65260, VI 00 Broadcast KCAN, SCAN, BCAN 244 Trip Distance 65248, VD 00 Broadcast KCAN, SCAN, BCAN 245 Total Vehicle Distance 65248, VD 00 Broadcast KCAN, SCAN, BCAN 247 Engine Total Hours of Operation 65253, HOURS 00 Broadcast KCAN, SCAN, BCAN 248 Total Power Takeoff Hours 65255, VH 00 Broadcast KCAN, SCAN, BCAN 249 Engine Total Revolutions 65253, HOURS 00 Broadcast KCAN, SCAN, BCAN 250 Engine Total Fuel Used 65257, LFC1 00 Broadcast KCAN, SCAN, BCAN 512 Driver's Demand Engine - Percent Torque 61444, EEC1 00 Broadcast KCAN, SCAN, BCAN 513 Actual Engine - Percent Torque 61444, EEC1 00 Broadcast KCAN, SCAN, BCAN

518 Engine Requested Torque/Torque Limit 0, TSC1 39 249 (DA specific) KCAN, SCAN, BCAN

518 Engine Requested Torque/Torque Limit 0, TSC1 7, 33 00 (DA specific) KCAN, SCAN, BCAN

523 Transmission Current Gear 61445, ETC2 03 Broadcast KCAN, SCAN, BCAN 524 Transmission Selected Gear 61445, ETC2 03 Broadcast KCAN, SCAN, BCAN

525 Transmission Requested Gear 256, TC1 03 255 (DA specific) KCAN, SCAN, BCAN

525 Trans Requested Gear 256, TC1 7, 33 03 (DA specific) KCAN, SCAN, BCAN

526 Transmission Actual Gear Ratio 61445, ETC2 03 Broadcast KCAN, SCAN, BCAN 527 Cruise Control States 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 527 Cruise Control States 65265, CCVS1 00 Broadcast KCAN, SCAN 558 Accelerator Pedal1 Low Idle Switch EEC2, 61443 00 Broadcast KCAN, SCAN, BCAN 559 Accelerator Pedal Kick down Switch 61443, EEC2 00 Broadcast KCAN, SCAN, BCAN 560 Transmission Driveline Engaged 61442, ETC1 03 Broadcast KCAN, SCAN, BCAN 561 ASR Engine Control Active 61441, EBC1 39 Broadcast KCAN, SCAN, BCAN 562 ASR Brake Control Active 61441, EBC1 39 Broadcast KCAN, SCAN, BCAN 563 Anti-Lock Braking (ABS) Active 61441, EBC1 39 Broadcast KCAN, SCAN, BCAN

573 Transmission Torque Converter Lockup Engaged

61442, ETC1 03 Broadcast KCAN, SCAN, BCAN

574 Transmission Shift In Process 61442, ETC1 03 Broadcast KCAN, SCAN, BCAN 590 Engine Idle Shutdown Timer State 65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN

CAN Communications

Peterbilt Motors Company 6-5

6 590 Engine Idle Shutdown Timer State 65252, SHUTDN 39 Broadcast KCAN, SCAN, BCAN 591 Engine Idle Shutdown Timer Function 65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN 591 Engine Idle Shutdown Timer Function 65252, SHUTDN 39 Broadcast KCAN, SCAN, BCAN 592 Engine Idle Shutdown Timer Override 65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN 593 Engine Idle Shutdown has Shutdown Engine 65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN 594 Engine Idle Shutdown Driver Alert Mode 65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN 595 Cruise Control Active 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 595 Cruise Control Active 65265, CCVS1 00 Broadcast KCAN, SCAN, BCAN 596 Cruise Control Enable Switch 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 597 Brake Switch 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 598 Clutch Switch 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 599 Cruise Control Set Switch 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 600 Cruise Control Coast (Decelerate) Switch 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 601 Cruise Control Resume Switch 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 602 Cruise Control Accelerate Switch 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 606 Engine Momentary Overspeed Enable 61442, ETC1 03 Broadcast KCAN, SCAN, BCAN 607 Progressive Shift Disable 61442, ETC1 03 Broadcast KCAN, SCAN, BCAN

684 Requested % Clutch Slip 256, TC1 7, 33 03 (DA specific) KCAN, SCAN, BCAN

695 Engine Override Control Mode 0, TSC1 7, 33 00 (DA specific) KCAN, SCAN, BCAN

696 Engine Requested Speed Control Conditions 0, TSC1 7, 33 00 (DA specific) KCAN, SCAN, BCAN

897 Override Control Mode Priority 0, TSC1 7, 33 00 (DA specific) KCAN, SCAN, BCAN

898 Engine Requested Speed/Speed Limit 0, TSC1 7, 33 00 (DA specific) KCAN, SCAN, BCAN

899 Engine Torque Mode 61444, EEC1 00 Broadcast KCAN, SCAN, BCAN 917 Total Vehicle Distance (High Resolution) 65217, VDHR 39 Broadcast KCAN, SCAN, BCAN 969 Remote Accelerator Enable Switch 61441, EBC1 00 Broadcast KCAN, SCAN, BCAN

970 Engine Auxiliary Shutdown Switch 61441, EBC1 7, 33, 160 Broadcast KCAN, SCAN, BCAN

974 Remote Accelerator Pedal Position 61443, EEC2 7, 33 Broadcast KCAN, SCAN, BCAN 974 Remote Accelerator Pedal Position 61443, EEC2 00 Broadcast KCAN, SCAN, BCAN 975 Engine Fan 1 Estimated Percent Speed 65213, FD1 00 Broadcast KCAN, SCAN, BCAN 976 PTO Governor State 65265, CCVS1 39 Broadcast KCAN, SCAN, BCAN 976 PTO Governor State 65265, CCVS1 00 Broadcast KCAN, SCAN, BCAN 976 PTO Governor State 65265, CCVS1 7, 33 Broadcast KCAN, SCAN, BCAN 977 Fan Drive State 65213, FD1 00 Broadcast KCAN, SCAN, BCAN

979 Engine Remote PTO Governor Preprogrammed Speed Control Switch

65264, PTO 7, 33 Broadcast KCAN, SCAN, BCAN

979 Engine Remote PTO Governor Preprogrammed Speed Control Switch

65264, PTO 00 Broadcast KCAN, SCAN, BCAN

980 Engine PTO Governor Enable Switch 65264, PTO 7, 33 Broadcast KCAN, SCAN, BCAN

CAN Communications

Peterbilt Motors Company 6-6

6 980 Engine PTO Governor Enable Switch 65264, PTO 00 Broadcast KCAN, SCAN, BCAN 982 Engine PTO Governor Resume Switch 65264, PTO 7, 33 Broadcast KCAN, SCAN, BCAN 984 Engine PTO Governor Set Switch 65264, PTO 7, 33 Broadcast KCAN, SCAN, BCAN 985 A/C High Pressure Fan Switch 65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN

1028 Total Engine PTO Governor Fuel Used 65203, LFI1 00 Broadcast KCAN, SCAN, BCAN 1040 Total Fuel Used (Gaseous) 65199, GFC 00 Broadcast KCAN, SCAN, BCAN 1081 Engine Wait to Start Lamp 65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN 1087 Service Brake Circuit 1 Air Pressure 65198, AIR1 39 Broadcast KCAN, SCAN, BCAN 1087 Service Brake Circuit1 Air Pressure 65198, AIR1 11 Broadcast KCAN, SCAN, BCAN 1087 Service Brake Circuit1 Air Pressure 65198, AIR1 48 Broadcast KCAN, SCAN, BCAN 1088 Service Brake Circuit 2 Air Pressure 65198, AIR1 39 Broadcast KCAN, SCAN, BCAN 1090 Air Suspension Supply Pressure 1 65198, AIR1 23 Broadcast KCAN, SCAN, BCAN 1107 Engine Protection System Timer State 65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN 1108 Engine Protection System Timer Override 65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN

1109 Engine Protection System Approaching Shutdown

65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN

1110 Engine Protection System Approaching Shutdown

65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN

1111 Engine Protection System Configuration 65252, SHUTDN 00 Broadcast KCAN, SCAN, BCAN

1172 Engine Turbocharger1 Compressor Intake Temperature

65178, TCI2 00 Broadcast KCAN, SCAN, BCAN

1184 Engine Turbocharger1 Turbine Outlet Temperature

TCI5, 65175 00 Broadcast KCAN, SCAN, BCAN

1214 Suspect Parameter Number 65226, DM1 39 Broadcast KCAN, SCAN 1215 Failure Mode Identifier 65226, DM1 39 Broadcast KCAN, SCAN 1216 Occurrence Count 65226, DM1 39 Broadcast KCAN, SCAN 1437 Road Speed Limit Status 61443, EEC2 00 Broadcast KCAN, SCAN, BCAN

1482 Source Address of Controlling Device for Transmission Control

61442, ETC1 03 Broadcast KCAN, SCAN, BCAN

1483 Source Address of Controlling Device for Engine Control

61444, EEC1 00 Broadcast KCAN, SCAN, BCAN

1487 Illumination Brightness Percent 53248, CL 39 74 (DA specific) KCAN, SCAN

1639 Fan Speed 65213, FD1 00 Broadcast KCAN, SCAN, BCAN 1675 Engine Starter Mode 61444, EEC1 00 Broadcast KCAN, SCAN, BCAN 1706 SPN Conversion Method 65226, DM1 39 Broadcast KCAN, SCAN

1761 Aftertreatment 1 Diesel Exhaust Fluid Tank Volume

65110, AT1T1I1 00 Broadcast KCAN, SCAN, BCAN

1807 Steering Wheel Angle 61449, VDC2 11, 62 Broadcast KCAN, SCAN, BCAN

1854 TransMode3 256, TC1 7, 33 03 (DA specific) KCAN, SCAN, BCAN

1856 Seat Belt Switch 57344, CM1 39 255 (DA specific) KCAN, SCAN

2347 High Beam Head Light Command 65089, LCMD 39 Broadcast KCAN, SCAN, BCAN

CAN Communications

Peterbilt Motors Company 6-7

6

2347 High Beam Head Light Command 65089, LCMD 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2349 Low Beam Head Light Command 65089, LCMD 39 Broadcast KCAN, SCAN, BCAN

2349 Low Beam Head Light Command 65089, LCMD 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2367 Left Turn Signal Lights Command 65089, LCMD 39 Broadcast KCAN, SCAN, BCAN

2367 Left Turn Signal Lights Command 65089, LCMD 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2369 Right Turn Signal Lights Command 65089, LCMD 39 Broadcast KCAN, SCAN, BCAN

2369 Right Turn Signal Lights Command 65089, LCMD 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2371 Left Stop Light Command 65089, LCMD 39 Broadcast KCAN, SCAN, BCAN

2371 Left Stop Light Command 65089, LCMD 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2373 Right Stop Light Command 65089, LCMD 39 Broadcast KCAN, SCAN, BCAN

2373 Right Stop Light Command 65089, LCMD 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2385 Rotating Beacon Light Command 65089, LCMD 39 Broadcast KCAN, SCAN, BCAN

2385 Rotating Beacon Light Command 65089, LCMD 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2387 Tractor Front Fog Lights Command 65089, LCMD 39 Broadcast KCAN, SCAN, BCAN

2387 Tractor Front Fog Lights Command 65089, LCMD 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2391 Back Up Light and Alarm Horn Command 65089, LCMD 39 Broadcast KCAN, SCAN, BCAN

2391 Back Up Light and Alarm Horn Command 65089, LCMD 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2403 Running Light Command 65089, LCMD 39 Broadcast KCAN, SCAN, BCAN

2403 Running Light Command 65089, LCMD 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2432 Engine Demand Percent Torque 61444, EEC1 00 Broadcast KCAN, SCAN, BCAN 2538 TransMode3Indicator 65098, ETC7 03 Broadcast KCAN, SCAN, BCAN

2540 Parameter Group Number (RQST) 59904, RQST 251 255 (DA specific) KCAN, SCAN

2540 Parameter Group Number (RQST) 59904, RQST 7, 33, 160

00 (DA specific) KCAN, SCAN, BCAN

2609 Cab A/C Refrigerant Compressor Outlet Pressure

64993, CACI 25 Broadcast KCAN, SCAN, BCAN

2641 Horn Switch 64980, CM3 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2863 Front Operator Wiper Switch 64973, OWW 39 Broadcast KCAN, SCAN, BCAN 2873 Work Light Switch 64972, OEL 39 Broadcast KCAN, SCAN, BCAN

2873 Work Light Switch 64972, OEL 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2875 Hazard Light Switch 64972, OEL 7, 33, 160 Broadcast KCAN, SCAN, BCAN

2876 Turn Signal Switch 64972, OEL 39 Broadcast KCAN, SCAN 2979 Vehicle Acceleration Rate Limit Status 61443, EEC2 39 Broadcast KCAN, SCAN, BCAN

CAN Communications

Peterbilt Motors Company 6-8

6 2979 Vehicle Acceleration Rate Limit Status 61443, EEC2 00 Broadcast KCAN, SCAN, BCAN

3026 Transmission Oil Level 1 Measurement Status

65272, TRF1 03 Broadcast KCAN, SCAN, BCAN

3027 Transmission Oil Level 1 High / Low 65272, TRF1 03 Broadcast KCAN, SCAN, BCAN 3028 Transmission Oil Level 1 Countdown Timer 65272, TRF1 03 Broadcast KCAN, SCAN, BCAN

3031 Aftertreatment 1 Diesel Exhaust Fluid Tank Temperature 1

65110, AT1T1I1 00 Broadcast KCAN, SCAN, BCAN

3246 Aftertreatment 1 Diesel Particulate Filter Outlet Temperature

64947, AT1OG2 00 Broadcast KCAN, SCAN, BCAN

3349 TSC1 Transmission Rate 0, TSC1 7, 33 00 (DA specific) KCAN, SCAN, BCAN

3350 TSC1 Control Purpose 0, TSC1 7, 33 00 (DA specific) KCAN, SCAN, BCAN

3357 Actual Maximum Available Engine - Percent Torque

61443, EEC2 00 Broadcast KCAN, SCAN, BCAN

3363 Aftertreatment 1 Diesel Exhaust Fluid Tank Heater

65110, AT1T1I1 00 Broadcast KCAN, SCAN, BCAN

3447 Remote PTO Governor Preprogrammed Speed Control Switch #2

65264, PTO 7, 33 Broadcast KCAN, SCAN, BCAN

3462 Engagement Status 64932, PTODE 7, 33 Broadcast KCAN

3462 Engagement Status 64932, PTODE 7, 33 03 (DA specific) SCAN, BCAN

3543 Engine Operating State 64914, EOI 00 Broadcast KCAN, SCAN, BCAN 3606 Engine Controlled Shutdown Request 64914, EOI 00 Broadcast KCAN, SCAN, BCAN

3607 Engine Emergency (Immediate) Shutdown Indication

64914, EOI 00 Broadcast KCAN, SCAN, BCAN

3609 Aftertreatment 1 Diesel Particulate Filter Intake Pressure

64908, AT1GP 00 Broadcast (255) KCAN, SCAN, BCAN

3610 Aftertreatment 1 Diesel Particulate Filter Outlet Pressure

64908, AT1GP 00 Broadcast KCAN, SCAN, BCAN

3673 Engine Throttle Valve2 Position 65266, LFE1 00 Broadcast KCAN, SCAN, BCAN

3695 Aftertreatment Regeneration Inhibit Switch 57344, CM1 7, 33, 160

255 (DA specific) KCAN, SCAN, BCAN

3695 Aftertreatment Regeneration Inhibit Switch 57344, CM1 39 255 (DA specific) KCAN, SCAN, BCAN

3696 Aftertreatment Regeneration Force Switch 57344, CM1 7, 33, 160

255 (DA specific) KCAN, SCAN, BCAN

3696 Aftertreatment Regeneration Force Switch 57344, CM1 00 255 (DA specific) KCAN, SCAN, BCAN

3696 Force Regen 57344, CM1 39 255 (DA specific) KCAN, SCAN, BCAN

3697 Diesel Particulate Filter Lamp Command 64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3698 Exhaust System High Temperature Lamp Command

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3700 Aftertreatment Diesel Particulate Filter Active Regeneration Status

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3701 Aftertreatment Diesel Particulate Filter Status

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

CAN Communications

Peterbilt Motors Company 6-9

6

3702 Diesel Particulate Filter Active Regeneration Inhibited Status

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3703 Diesel Particulate Filter Active Regeneration Inhibited Due to Inhibit Switch

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3704 Diesel Particulate Filter Active Regeneration Inhibited Due to Clutch Disengaged

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3705 Diesel Particulate Filter Active Regeneration Inhibited Due to Service Brake Active

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3706 Diesel Particulate Filter Active Regeneration Inhibited Due to PTO Active

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3707 Diesel Particulate Filter Active Regeneration Inhibited Due to Accelerator Pedal Off Idle

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3708 Diesel Particulate Filter Active Regeneration Inhibited Due to Out of Neutral

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3709 Diesel Particulate Filter Active Regeneration Inhibited Due to Vehicle Speed Above Allowed Speed

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3710 Diesel Particulate Filter Active Regeneration Inhibited Due to Parking Brake Not Set

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3711 Diesel Particulate Filter Active Regeneration Inhibited Due to Low Exhaust Temperature

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3712 Diesel Particulate Filter Active Regeneration Inhibited Due to System Fault Active

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3713 Diesel Particulate Filter Active Regeneration Inhibited Due to System Timeout

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3716 Diesel Particulate Filter Active Regeneration Inhibited Due to Engine Not Warmed Up

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3717 Diesel Particulate Filter Active Regeneration Inhibited Due to Vehicle Speed Below Allowed Speed

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3718 Diesel Particulate Filter Automatic Active Regeneration Initiation Configuration

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

3719 Aftertreatment 1 Diesel Particulate Filter Soot Load Percent

64891, AT1S1 00 Broadcast KCAN, SCAN, BCAN

3721 Aftertreatment 1 Diesel Particulate Filter Time Since Last Active Regeneration

64891, AT1S1 00 Broadcast KCAN, SCAN, BCAN

3948 At least one PTO engaged 64932, PTODE 39 Broadcast KCAN, SCAN, BCAN 4154 Actual Engine - Percent Torque (Fractional) 61444, EEC1 00 Broadcast KCAN, SCAN, BCAN

4175 Diesel Particulate Filter Active Regeneration Forced Status

64892, DPFC1 00 Broadcast KCAN, SCAN, BCAN

4191 Engine Requested Torque (Fractional) 0, TSC1 7, 33 00 (DA specific) KCAN, SCAN, BCAN

4206 Message Counter 0, TSC1 7, 33 00 (DA specific) KCAN, SCAN, BCAN

4207 Message Checksum 0, TSC1 7, 33 00 (DA specific) KCAN, SCAN, BCAN

4765 Aftertreatment 1 Diesel Oxidation Catalyst Intake Temperature

64800, A1DOC1 00 Broadcast KCAN, SCAN, BCAN

CAN Communications

Peterbilt Motors Company 6-10

6

4816 Transmission Torque Converter Lockup Transition in Process

61442, ETC1 03 Broadcast KCAN, SCAN, BCAN

5078 Engine Amber Warning Lamp Command 64775, DLCC1 00 Broadcast KCAN, SCAN, BCAN 5079 Engine Red Stop Lamp Command 64775, DLCC1 00 Broadcast KCAN, SCAN, BCAN 5082 Engine Oil Pressure Low Lamp Command 64775, DLCC1 00 Broadcast KCAN, SCAN, BCAN

5083 Engine Coolant Temperature High Lamp Command

64775, DLCC1 00 Broadcast KCAN, SCAN, BCAN

5084 Engine Coolant Level Low Lamp Command 64775, DLCC1 00 Broadcast KCAN, SCAN, BCAN 5086 Engine Air Filter Restriction Lamp Command 64775, DLCC1 23 Broadcast KCAN, SCAN, BCAN

5087 Vehicle Battery Voltage Low Lamp Command 64774, DLCC2 23 Broadcast KCAN, SCAN, BCAN

5088 Vehicle Fuel Level Low Lamp Command 64774, DLCC2 23 Broadcast KCAN, SCAN, BCAN

5245 Aftertreatment Diesel Exhaust Fluid Tank Low Level Indicator

65110, AT1T1I1 00 Broadcast KCAN, SCAN, BCAN

5246 Aftertreatment SCR Operator Inducement Severity

65110, AT1T1I1 00 Broadcast KCAN, SCAN, BCAN

5398 Estimated Pumping - Percent Torque 61443, EEC2 00 Broadcast KCAN, SCAN, BCAN 5399 DPF Thermal Management Active 61443, EEC2 00 Broadcast KCAN, SCAN, BCAN 5400 SCR Thermal Management Active 61443, EEC2 00 Broadcast KCAN, SCAN, BCAN

5466 Aftertreatment 1 Diesel Particulate Filter Soot Load Regeneration Threshold

64891, AT1S1 00 Broadcast KCAN, SCAN, BCAN

5676 Forward Collision Advanced Emergency Braking System State

61487, AEBS1 42 Broadcast KCAN, SCAN

5825 Driver Warning System Indicator Status 65279, OI 00 Broadcast KCAN, SCAN, BCAN 8484 Demanded Brake Application Pressure 61712, B2 39 Broadcast KCAN, SCAN, BCAN

12308 Headlamp Emergency Flash Switch 64972, OEL 7, 33 Broadcast SCAN 12308 Headlamp Emergency Flash Switch 64972, OEL 7, 33 Broadcast KCAN 12308 Headlamp Emergency Flash Switch 64972, OEL 7, 33 Broadcast BCAN 12964 Auxiliary Lamp Group Switch 64972, OEL 39 Broadcast KCAN, SCAN, BCAN

12964 Auxiliary Lamp Group Switch 64872, OEL 7, 33, 160 Broadcast KCAN, SCAN, BCAN

13105 Engine Oil Temperature High Lamp Command

64775, DLCC1 23 Broadcast KCAN, SCAN, BCAN

13108 Primary Air Pressure Low Lamp Command 64774, DLCC2 23 Broadcast KCAN, SCAN, BCAN 13109 Secondary Air Pressure Low Lamp Command 64774, DLCC2 23 Broadcast KCAN, SCAN, BCAN

13116 Transmission Oil Temperature High Lamp Command

64775, DLCC1 23 Broadcast KCAN, SCAN, BCAN

13132 Air Suspension Supply Pressure 2 64195, AIR3 23 Broadcast KCAN, SCAN, BCAN

SECTION 7 ELECTRICAL INTRODUCTION This section is written to provide information to the body builder when installing equipment into vehicles built with multiplexed instrumentation. The technology presented by VECU level instrumentation integrates J-1939 CAN data communications between controllers and equipment on the vehicle. This section is intended to address how to work in aftermarket equipment while still maintaining full functionality of the OEM vehicle. These topics apply to 520 chassis built with a Vehicle Electronic Control Unit (VECU). The electrical architecture for these trucks will be named VMUX which replaces NAMUX2. This system integrates a parallel control unit to manage outbound messages via a faster baud rate 500kbps and FCAN signals for the chassis module(s). Since the F-CAN has moved to the VECU, the VCAN is divided into VCAN1 and VCAN2. The second CAN is dedicated to OBD communication. The most important advancement of electrical instrumentation is the implementation of the VECU controller. While it is still possible to wire completely outside of the VECU system, utilizing the VECU functions will make a cleaner installation and will maintain OEM functionality. VECU expands controls to air operated devices by receiving input from dash switches, remote (aftermarket) switches, sensors mounted to the aftermarket equipment and other vehicle parameters (engine speed, transmission status etc.) With the proper programming, the VECU will then process the inputs and will create a J- 1939 Data instruction which is communicated to another controller outside the cab called the Chassis Module. This chassis module receives the instruction and communicates the information to the air solenoid bank. Then 12V power will open the solenoid and supply air pressure the specified air circuit. The chassis module can also supply voltage to other systems on the chassis. ELECTRICAL ACRONYM LIBRARY

Acronym Definition CAN Controller Area Network DTC Diagnostics Trouble Code ECM Engine Control Module ECU Electrical Control Unit EOA Electric Over Air EOH Electric Over Hydraulic J-1939 SAE CAN Communication Standard LIN Local Interconnect Network MSB Master Solenoid Bank MSM Master Switch Module MUX Multiplex Switch OBD On Board Diagnostics OEM Original Equipment Manufacture PCC Predictive Cruise Control PDC Power Distribution Center PGN Parameter Group Number PTO Power Take Off RP1226 TMS Messaging Standard SPN Suspect Parameter Number TCM Transmission Control Module VECU Vehicle Electrical Control Unit

ELECTRICAL

Peterbilt Motors Company 7-2

7 ELECTRICAL WIRING CIRCUIT CODES The wire system uses 10 different colors and one striped wire color. Each wire has a minimum of seven characters, with the first three characters as the wire color. The remaining four characters are related to the wire services. The colors determine the circuits function as follows:

ELECTRICAL WIRE CIRCUIT CODE TABLES

Number Category XXX0000 through XXX0999 General XXX1000 through XXX1999 Power Supply XXX2000 through XXX2999 Lighting XXX3000 through XXX3999 Powertrain XXX4000 through XXX4999 Instrumentation XXX5000 through XXX5999 Safety systems XXX6000 through XXX6999 Convenience, Security XXX7000 through XXX7999 HVAC XXX8000 through XXX8999 Undefined XXX9000 through XXX9999 Trailer/Body Connections

ELECTRICAL

Peterbilt Motors Company 7-3

7 MULTIPLEX SYSTEM The VECU electrical architecture uses a multiplexing system. Multiplexing can be defined as the process of sending multiple digital signals on the same shared medium at the same time. These signals are introduced into the multiplexing system through data connection points which are defined by J1939 backbone. CAN BUS SYSTEM OVERVIEW

REVDRAWING

TITLE

VEHICLE NETWORK ARCHITECTURE 520 VMUX

Q98-5002E0021-001 AUTHOR

AT. Lafferty

THIS DRAWING AND THE INF ORM AT ION CONTAINED HEREIN IS PROPRIETARY TO PACCAR INC. AND SHALL NOT BE REPRODUCED, COPIED, OR DISCLOSED IN WHOLE OR IN PART, OR USED F OR MANUFACTURE OR F OR ANY OT HER PURPOSE WIT HO UT THE WRIT TEN PERM ISSION OF PACCAR INC.

Engine

Bendix ABS/ATC

V-CAN 2 (OBD)

V-CAN 1

C-CAN 500 kb/s

Chassis Module Primary

(CAN Gateway)

F-CAN 500 kb/s

VECU 2 (CAN Gateway)

T-CAN 250 kb/s Allison 3K/4K

TCM

Allison Shifter Cab

ACC RADAR

Master Switch Module

S-LIN1

Chassis Module Secondary

RP1226 Cab

S-CAN 500 kb/s

MUX Switches

MUX Switches

S-LIN2

R

R

R

R

R

R

R

R

R

R

R

Retarder

R

K-CAN 250 kb/s

R

DC

Telematics Pre-wire

MCS3

R

B-CAN 500 kb/s

R

500 kb/s

500 kb/s

V-LIN1

Cluster

R

R

Secondary MCS3

Secondary Allison

Shifter Cab

Solenoid Bank 1

RP170 Powertrain

D-CAN 500 kb/s

R

100 Mb/s Ethernet

OBD Connector

Ethernet Connector

OBD Scantool

Radio Head

Remote Diagnostics

V-LIN2

Secondary Cluster

LDWS Brake Wear ECU

Cab mounted

Chassis mounted

Powertrain mounted

New/ Modified w.r.t. 2021 MD VMUX

Future Optional Connector

ResistorR

Daisy ChainDCInvestigation

Off-Board GPS 3G/4G Wireless Data

Bluetooth WiFi

USB

PACCAR PROPRIETARY FOR INTERNAL USE ONLY

A-CAN 250 kb/s

E-CAN 250 kb/s

R R

SC

PeopleNet System

Remote Display /

Body Controller / PTO (CID) / Telematics / ELD (CID) (250 kb/s)

Remote Display /

Body Controller / PTO (CID) / Telematics / ELD (CID) (500 kb/s)

Remote Display /

Body Controller/ PTO (CID) (500 kb/s)

Remote Display /

Body Controller/ PTO (CID) (250 kb/s)

Ethernet Connector

100 Mb/s Ethernet

Service Tool/CHET

Optional Gauges

G-LIN

A DIV IS ION OF

DWIM

Speedo

Side Object Detection

Left

Side Object Detection

Right

CAN BUS SPEEDS AND CIRCUIT DESIGNATION

J1939-14 (500KBPS): J1939-15 (250KBPS): B-CAN 0813 Body Builder T-CAN 0828 Transmission C-CAN 0821 Cab K-CAN 0829 Customer Installed Devices D-CAN 0822 Diagnostics F-CAN 0819 Frame

G-CAN 0825 Safety Systems S-CAN 0827 Infotainment and Mobile Gateway V-CAN1 0812 Vehicle1 V-CAN2 0823 Vehicle2

ELECTRICAL

Peterbilt Motors Company 7-4

7 ELECTRICAL COMPONENT OVERVIEW

ELECTRICAL

Peterbilt Motors Company 7-5

7 IN CAB CAN BASED MESSAGING CONNECTOR RP1226 CONNECTOR The RP1226 connectors are located under the body builder panel (near the PDC) and behind the driver kick panel (LH for LH and dual drive, RH for RH drive). The RP1226 connector can be used for after-market telematics, ELD, body controls, and PTO controls. There will be multiple bus speeds available, K-CAN for 250kbps and S-CAN for 500 kbps. The RP1226 provides defined messages and major telematics supplier data for customer use.

Pin Description 1 PROTECTED POWER 2 J1939 S-CAN (+) 4 J1939 K-CAN (+) 7 IGNITION POWER 8 GROUND 9 J1939 S-CAN (-)

11 J1939 K-CAN (-) 14 CONSTANT BATTERY

ELECTRICAL

Peterbilt Motors Company 7-6

7

RP1226 CONNECTOR LOCATIONS

RP1226 Connector Locations LH location for LH and dual drive cabs, RH location for RH drive cab

ELECTRICAL

Peterbilt Motors Company 7-7

7 ELECTRIC ENGAGED EQUIPMENT RP170 CONNECTOR There are three RP170 connectors total. The 8-pin and 31-pin are located inside the cab under the body builder panel. The 14-pin connector is located inside the left hand frame rail.

RP170 CONNECTOR LOCATIONS 8 PIN & 31 PIN

RP170 8-Pin & 31-Pin Connectors

ELECTRICAL

Peterbilt Motors Company 7-8

7 RP170 CONNECTOR LOCATIONS 14 PIN

RP170 14-Pin Connector

ELECTRICAL

Peterbilt Motors Company 7-9

7 8-PIN CONNECTOR

PIN DESCRIPTION A BATTERY (20A) B IGNITION (20A) C IGNITION (20A) D CONSTANT BATTERY (15A) E IGN THRU REV CIRCUIT (25A) F GROUND G GROUND H GROUND

ELECTRICAL

Peterbilt Motors Company 7-10

7 31-PIN CONNECTOR

PIN DESCRIPTION PIN DESCRIPTION FROM ENGINE FROM TRANSMISSION

1 TACH (DIESEL) DIAG TEST SWITCH (NG) 15 TCM IGNITION POWER (12V)

2 ABS RETARDER 16 ROAD SPEED SIGNAL 3 THROTTLE LIMIT 17 TCM SIGNAL RETURN 4 THROTTLE ADVANCE 18 AT123 INPUT 5 K-CAN HIGH (250K) 19 PTO CONTROLS INPUT 6 K-CAN LOW (250K) 20 PUMP MODE ENABLED INPUT

7 THROTTLE INTERLOCK (MX) TORQUE LIMIT (CUMMINS) 21 AUTO NEUTRAL INPUT

8 APPLICATION SPEED LIMITER (MX) BLANK (CUMMINS) 22

SHIFT SELECTOR TRANSMISSION INPUT

9 GROUND (MX) ECM COMMON (CUMMINS) 23 SERVICE BRAKE STATUS INPUT

10 REMOTE PTO ENABLE 24 AUTO NEUTRAL INPUT 11 REMOTE PTO SET 25 PTO DRIVE INTERFACE OUTPUT 12 REMOTE PTO RESUME 26 NEUTRAL INDICATOR OUTPUT

13 PARK BRAKE APPLIED 27 OUTPUT SPEED INDICATOR OUTPUT

14 BLANK 28 SUMP/RETARDER TEMP INDICATOR OUTPUT

29 NEUTRAL START SIGNAL 30 IGNITION (10A) 31 DUAL STEER RH ACTIVE SIGNAL

ELECTRICAL

Peterbilt Motors Company 7-11

7 14-PIN CONNECTOR

PIN DESCRIPTION 1 GROUND 2 BACKUP LIGHTS 3 LH TURN/STOP 4 RH TURN/STOP 5 TAIL LAMPS 6 CLEARANCE LAMPS 7 STOP LAMPS 8 BLANK 9 BLANK

10 BLANK 11 BLANK 12 BLANK 13 LH MARKER TURN LAMPS 14 RH MARKER TURN LAMPS

ELECTRICAL

Peterbilt Motors Company 7-12

7 ENGINE HARNESS 12 PIN CONNECTOR PACCAR MX Engines Chassis must be ordered with the appropriate option to have a 12 pin connector on the chassis harness. All signals will feed into the Chassis Modules. Wiring Function Description: Connect pin 5 and pin 6 to pin 8 to activate PTO Mode Control (PMC) and Enable PTO Speed Control (PSC).

"Bump up" Engine Speed: Connect pins 2 to pin 8 momentarily "Accelerate" Engine Speed: Connect pins 2 to pin 8 until desired RPM is reached then disconnect "Bump down" Engine Speed: Connect pin 1 to pin 8 momentarily "Decelerate" Engine Speed: Connect pins 1 to pin 8 until desired RPM is reached then disconnect 0-5v Variable Voltage Remote Throttle: See PTO section

ELECTRICAL

Peterbilt Motors Company 7-13

7

PACCAR Recommended PTO Wiring

Pin 1-Resume/decel Wire #: GRA3513-5 Signal: LOW/GROUND

Pin 2-Set/accel Wire #: GRA3512-5 Signal: LOW/GROUND

Pin 3-Return for variable voltage throttle Wire #: GRN3144-2

Pin 4-Signal for variable voltage throttle Wire #: BLU3144-2 Signal: 0-5V Note: See PTO Section for detail on VVRT

Pin 5-PTO Engaged Wire #: GRA3511-19 Signal: DUAL ACTIVATION Note: Same circuit as P201 connector, pin 2

Pin 11-12V 10A Body Ignition Wire #: ORN1220-86 Fuse: CHASSIS PDC F25 Amperage: 10A Pin 10-5V supply for variable voltage throttle Wire #: VIO3144-2 Source: Chassis Module Primary

Pin: 8-Vehicle Ground Wire #: WHT3511-2 Notes: Recommended source for all ground signals on this connector

Pin 6-REMOTE PTO ENABLE Wire #: GRA3511-63 Signal: LOW/GROUND

Pin 7-12V 10A Body Ignition Wire #: ORN1220-30 Fuse: CHASSIS PDC F25 Amperage: 10A

Pin 9-MX Application Speed Limiter Wire #: GRA3100-3 Signal: DUAL ACTIVATION Destination: Standard Chassis Module

ELECTRICAL

Peterbilt Motors Company 7-14

7 Cummins Engines 12 Pin Connector Chassis must be ordered with the appropriate option to have a 12 pin connector on the engine harness. The Body IGN signal was moved off the engine harness connector, so the Chassis Harness will include the PTO layer to insert the Body IGN signal back into the 12-way connector. Signals that feed directly to the engine ECM typically will be active low signals. Connect pins 3 and 5 for simple PTO ON/OFF signal. For Remote throttle bump, you must connect pins 3 & 6. Having a momentary switch to signal ground on pins 2 and 1 will then increase/decrease engine speed. Engine speed will depend on how engine is programmed. Unless otherwise specified, engine is set by default for incremental speed increase. Full remote throttle control can be achieved with a twisted triple to pin 4, 10, and 11.

Pin Description 1 INPUT FOR REMOTE PTO RESUME (Active Low) 2 INPUT FOR REMOTE PTO SET (Active Low) 3 SWITCH RETURN FOR CUMMINS ENGINE

4 INPUT FOR REMOTE THROTTLE SENSOR CIRCUIT (TWISTED TRIPLE) 5 PTO ENGAGED SIGNAL (LOW = ENGAGED) 6 CRUISE ON/OFF (Active Low) 7 +12V 10A BODY IGN CHASSIS PDC F25 8 VEHICLE GROUND 9 TORQUE LIMIT INPUT (Active Low) 10 PWR SUPPLY +5V (TWISTED TRIPLE) 11 ANALOG RETURN (TWISTED TRIPLE) 12 REMOTE ACCELERATOR ENABLE (Active Low)

ELECTRICAL

Peterbilt Motors Company 7-15

7 ENGINE HARNESS CONNECTION LOCATION

MX11 Connection location

ELECTRICAL

Peterbilt Motors Company 7-16

7

L9N Connection location

ISX12N Connection location

ELECTRICAL

Peterbilt Motors Company 7-17

7 ENGINE HARNESS 8 PIN CONNECTOR PACCAR MX Engines Optional 8-pin PTO connector offers advanced PTO features, available only with MX engines. Option must be specd when the chassis is ordered. 8-pin connector is located BOC in RH frame rail.

Pin Description 1 12V IGNITION SIGNAL 2 PTO INTERLOCK INPUT (Active Low) 3 REMOTE PTO PRESET 3 (Active High) 4 REMOTE PTO PRESET 2 (Active High) 5 REMOTE PTO PRESET 1 (Active High) 6 REMOTE PTO PRESET INCREMENT + (Active High) 7 REMOTE PTO PRESET DECREMENT - (Active High) 8 VEHICLE GROUND

ELECTRICAL

Peterbilt Motors Company 7-18

7 POWER DISTRIBUTION CENTER CAB LOAD CENTER

ELECTRICAL

Peterbilt Motors Company 7-19

7 CHASSIS PDC

Chassis PDC Location on Stanchion BOC

ELECTRICAL

Peterbilt Motors Company 7-20

7 CHASSIS MODULE Chassis modules are replacing the legacy NAMUX2. Chassis modules are slave I/O drivers controlled by the VECU. Chassis modules have expanded functionality and option platform growth in comparison to the previous chassis node. There will be two chassis modules with one standard primary chassis module on all trucks and a secondary for optional content. The primary and secondary chassis modules will be mounted behind the cab on the stanchion. Chassis modules have built-in protections to prevent internal damage, are capable of detecting faults and storing DTCs. Chassis modules can also be diagnosed through the DAVIE service tool.

CHASSIS MODULE LOCATIONS

Chassis Modules Located on Stanchion BOC

ELECTRICAL

Peterbilt Motors Company 7-21

7 CHASSIS MODULE FUNCTION DESIGNATIONS

PRIMARY CHASSIS MODULE Exterior Lighting: Headlamps, Park/Tail, Turn, Brake, DRL, Fog Lights, Reverse etc. Axle Temperature Sensor Inputs Front Rear and Rear Kingpin Release Solenoid Control Primary Fuel Level Sensors Lift Axle Air Solenoid Controls 1st, 2nd Primary Transmission Neutral Position Switch Remote PTO/Throttle Control Inputs F-CAN Multiplexed EOA Solenoid Bank Control Main Transmission Oil Temp

SECONDARY CHASSIS MODULE

Axle Temperature Gauges Center Rear Lift Axle Air Solenoid Controls 3rd , Tag Tag Axle Lockout

ELECTRICAL

Peterbilt Motors Company 7-22

7 FUSE GROUPS PRIMARY CHASSIS MODULE

Fuse Group Function

F1 Electric Over Air Solenoid Kingpin Release Main Beam (aka High Beam) - LH Tractor Direction Indication and Hazard Lights - RH Rear (Brake Lamps Also)

F2 Front Tractor Position lights (Park Lamps) Tractor Direction Indication Hazard Side Turn Indicator LH Front Dipped Beam (aka Low Beam) - LH

F3 Lift Axle #2 Solenoid Tractor Direction Indication Hazard Side Turn Indicator RH Front Dipped Beam (aka Low Beam) - RH

F4 Main Beam (aka High Beam) - RH Fog/Driving Lights (Front) 1st Set

F5 Reverse Warning (aka Backup Alarm) (Rear) Direction Indication and Hazard Lights - LH Trailer

F6 Rear Tractor Position lights (Park Lamps) Reverse Lamps Tractor Direction Indication and Hazard Lights LH Rear (Brake Lamps Also)

F7 Lift Axle #1 Solenoid (Rear) Direction Indication and Hazard Lights - RH Trailer

SECONDARY CHASSIS MODULE

Fuse Group Function F2 Tag Axle Lockout F4 Lift Axle #3 Solenoid F5 Lift Axle #4 (Tag) Solenoid

ELECTRICAL

Peterbilt Motors Company 7-23

7 VECU

Fuse Group Function

G1 Starter Interrupt / Start Enable Relay Control Cab Dome Lamp Trailer Marker/Clearance Lamps

G2

Recirculating Header Fan - Low Speed Trailer Hotline Relay Allison MTD PTO Controls - PTO 1 Spot Lamp Work Lights (Flood Lamps) 1 Beacon/Strobe Trailer Brake Lamps Trailer/Cab Park Lamps Recirculating Header Fan - High Speed Right Hand Steer

G3 Cab Marker/Clearance Lamps Relay Output Washer Pump Control Windshield Wiper Control

G4 Dash PWM Backlighting Dash Illumination 2

ELECTRICAL

Peterbilt Motors Company 7-24

7 ELECTRIC OVER AIR SOLENOIDS Air solenoids are devices that translate the electrical signal into physical functions that controls the air pressure in various circuits. The air solenoids are mounted to a bracket outside the cab. The solenoids are designed to stack on each other so that they share a common air supply which reduces the amount of air lines on the vehicle. The aftermarket installer/final vehicle manufacturer needs to decide what type of valve to install and ensure that the documentation to the operator provides them with enough understanding of how the customized switches work. SOLENOID BANK DIAGRAM

ELECTRICAL

Peterbilt Motors Company 7-25

7 SOLENOID OVERVIEW LAYOUT

ELECTRICAL

Peterbilt Motors Company 7-26

7 MUX SOLENOID BANK FRAME MOUNTING LOCATION

Inside right hand rail between 1st and 2nd crossmember

MUX SOLENOID BANK CROSSMEMBER MOUNTING LOCATION

*Mounting location is determined by engineering and the configuration of the vehicle

ELECTRICAL

Peterbilt Motors Company 7-27

7 SWITCHES SWITCH OVERVIEW LAYOUT

Multiplexing = shorter wire bundles, improved diagnostics, and greater driver feedback. Safety critical switches use hybrid switch with hardwire for redundancy. The switches are less expensive with fewer wires behind the dash and on chassis. The switches are self-diagnosable to improve troubleshooting with DAVIE. Master Switch Module (MSM) LIN Communication to/from Switches CAN Communication to/from VECU SPARE SWITCHES

Spare switches offer customers and body builders a convenient way to control power and air to various sources, like a body or trailer. They should be flexible and easily configurable to meet the vast and unique needs of body builders. The Spare switches, along with all hybrid switch variants, are rated to 15 A of current.

ELECTRICAL

Peterbilt Motors Company 7-28

7 SPARE POWER Spare power connector P096 is located under the body builder panel towards the front on the right side. The mating harness is available from PACCAR parts with pre-labeled pigtails, S92-1250-1000. Any spare power requiring more than 20 amps must go directly to the battery box, not this spare circuit.

SPARE CIRCUIT CONNECTOR

Pin Spare Circuit No. Designation Fuse Max Rating

A RED0710-2 Spare Battery #2 20A

B RED0710-5 Spare Battery #1 20A

C ORN0752-4 Spare Accessory #1 20A

D WHT1500-102 Spare Ground 20A

E ORN0730-1 Spare Ignition #1 20A

F ORN0730-6 Spare Ignition #2 20A

H BRN2620-8 Backlight 20A

ELECTRICAL

Peterbilt Motors Company 7-29

7

TRANSMISSION BACKUP SIGNALS The back-up lamp signal can be accessed from P791 or P792 pin C tail lamp connector located on the chassis harness. It is recommended to use the RP170 connector, found on page 7-11 of this manual, as the preferred access point.

Mating Connector: Packard PN 12015713

ELECTRICAL

Peterbilt Motors Company 7-30

7 LIFT AXLES (PUSHERS & TAG) All truck lift axles (pushers and tag), are direct wire Electric-Only. The wiring comes from the Primary Chassis Module or Secondary Chassis Module, and goes direct to the axle mounted solenoid. This is not from the EoA Solenoid Bank. The activation signal comes from either a dash mounted MUX switch, or a hardwired switch that is mounted outside of the cab. There are a total of four lift axle controls available; 3 pushers and 1 tag axle, or 4 pushers and no tag. These are controlled with separate switches by default. The customer can order the following configurations; steerable, non- steerable, with auto-reverse, and with park brake interlock. A lift axle comes with a control switch (single or separate), a gauge, and a regulator valve. LIFT AXLE DIAGRAM

TRUCK LIFT AXLE LOGIC Lift Axle Type Raise Condition Logic Lower Condition Logic

Steerable Lift Axle w/o Auto-Reverse

- Lift Switch is Inactive OR - Park Brake Active OR - Trans in Reverse

- Lift Switch is Active AND - Park Brake Inactive AND - Trans Not in Reverse

Steerable Lift Axle with Auto-Reverse OR Non-Steerable Lift Axle w/o Park Brake

- Lift Switch is Inactive OR - Park Brake Active

- Lift Switch is Active AND - Park Brake Inactive

Non-Steerable Lift Axle with Park Brake - Lift Switch is Inactive AND - Park Brake Inactive

- Lift Switch is Active OR - Park Brake Active

ELECTRICAL

Peterbilt Motors Company 7-31

7 DIGITAL DISPLAY The standard display comes with a set of gauges. A limited number of additional gauges can be configured on the 7 digital display after the initial truck build using Paccar Vehicle Pro (PVP). Please contact your local Peterbilt dealership for assistance.

Gauges on the 7 Digital Display

TELLTALE ICONS Custom Telltales will no longer be available with a physical card inserted into the dash cluster. Instead, the body builder telltales will populate on the digital portion of the display from a limited list and can be reconfigured using PVP at your local Peterbilt dealership. The location of the telltale will be dependent on the configuration of the vehicle and what other telltales are present on the digital display. The Digital Display is capable of receiving up to 5 hardwire inputs to trigger the body builder (editable) telltales.

Body Builder Telltale Positions

ELECTRICAL

Peterbilt Motors Company 7-32

7 BODY BUILDER TELLTALE LOCATIONS

Body Builder Telltale Locations

SECTION 8 POWER TAKE-OFF (PTO) INTRODUCTION

A Power Take Off (PTO) provides a way to divert some or all of the trucks engine power to another component. There are a wide variety of PTO options available on a Peterbilt that are described below.

FIGURE 7-1. Power Take-Off Locations

TRANSMISSION MOUTED PTO GENERAL

MANUAL TRANSMISSIONS

This is the most common type of PTO that is used. On a manual transmission there are two locations for PTOs. There is a 6 bolt PTO on the right and an 8 bolt PTO on the bottom left (Figure 7.2). For more information go to www.roadranger.com and enter PTO Installation Guide in the search bar in the upper right corner.

FIGURE 7-2. HD Manual Transmission

8 POWER TAKE-OFF (PTO)

8-2 Peterbilt Motors Company

AUTOMATIC TRANSMISSIONS

On Allison transmissions there are two locations for PTOs. The Allison 4000 series has PTO locations at 1 and 8 oclock viewed from the back of the transmission. See Figure 7-3. The 4000HS transmissions do not have any PTO locations. The 3000 series Allison transmissions have PTO locations at 4 and 8 oclock (Figure 7-4). For more information on using PTOs with an Allison transmission go to www.allisontransmission.com and refer to the Rugged Duty Series Brochure and PTO Request Flyer which is available in a 1000/2000 version and a 3000/4000 version.

FIGURE 7-3. Allison 4000 Series FIGURE 7-4. Allison 3000 Series

INSTALLATION CLEARANCES

Some PTO configurations will have clearance issues with other components on the truck. With manual transmissions, a 6-bolt PTO on the right will typically clear most components. This is also true when 30 and 45 degree adapters are used. The 8-bolt bottom mount PTO will not have any issues. On Allison 4000 series transmissions, most PTOs will fit in the 1 oclock position without interfering with the cab. If a wet kit is used here, the dipstick housing will most likely need to be modified as it runs over the top of the transmission to the driver side of the vehicle. The PTO in the 8 oclock position is typically ok. There are some scenarios where the PTO will be very close to or could interfere with the rear spring shackle on the front suspension.

8 POWER TAKE-OFF (PTO)

8-3 Peterbilt Motors Company

FRONT ENGINE PTO

Front engine PTO (FEPTO) is sometimes used in vocational applications. When a FEPTO is specd on a truck, the cooling module has a pass-thru to allow for a shaft to be bolted to the front of the crankshaft and extend out to the front of the truck. The bumper will be extended out to mount the customer installed aftermarket device. Bumper extensions available are 9, 4-7/8, or no extension. See Figure 7-5 and Figure 7-6 for radiator installations with and without FEPTO provisions.

FIGURE 7-5. Cooling Module With FEPTO Provision FIGURE 7-6. Cooling Module Without FEPTO Provision

8 POWER TAKE-OFF (PTO)

8-4 Peterbilt Motors Company

REAR ENGINE PTO

Rear Engine PTO (REPTO) is also sometimes used in vocational applications. The REPTO is driven off the rear gear train on the engine. There is a 1350/1410 flange on the bell housing in the 1 oclock position that can be used to attach a hydraulic pump or driveshaft. See Figure 7-7 for an example. The REPTO flange will always be turning when the engine is running and the output rotation is the same as the engine. The Cummins ISL9 and PX-9 REPTO turns at a rate of 1.15:1. The Paccar MX-11 turns at a rate of 1.3:1.

FIGURE 7-7. REPTO Flywheel Housing

8

Peterbilt Motors Company

POWER TAKE-OFF (PTO)

8-5

INSTALLATION OF PTO

CHELSEA 890

The installation shown below in figures 7-10 through 7-12 are of the model 520 with a Chelsea 890 PTO.

FIGURE 7-10. Bottom View FIGURE 7-11. Rear View

FIGURE 7-12. Isometric View with Enhanced View

8

Peterbilt Motors Company

POWER TAKE-OFF (PTO)

8-6

MX PTO MODE CONTROL (PMC) MX PTO Mode Control (PMC) includes features, limits, and protections that are active in PTO Mode. It also includes PTO Speed Control (PSC) functionality that includes a variety of useful ways to control engine speed during PTO operation. Reference the VECU Programming Guide for detailed information on PTO Mode Control configuration, functionality and usage. MX PTO MODE ACTIVATION There are three ways to activate PTO Mode. PMC parameter(s) must be enabled on the vehicle in order for PTO Mode to activate.

Active feedback of physical PTO engagement o Trucks with factory installed PTOs or that are coded for Customer

Installed PTOs will come prewired to receive the PTO engaged signal. Active PTO Mode Switch

o The PTO Mode Switch can be configured at the time of order or in the aftermarket. The PTO Mode switch can be used to activate PTO Mode independent of PTO engagement and may be useful for trucks with FEPTOs or REPTOs that need the ability to use PMC features.

PTO Mode Request over the CAN bus MX PTO MODE CONTROL LOCATION Vehicles can be configured to control PTO functionality from a cab location and/or a remote location (outside the cab). Most PTO Mode Features and Interlocks have a cab station option and a remote station option. This allows a vehicle to be configured for two unique jobs. For example a vehicle could be configured for mobile cab station operation with one set of limits and stationary remote station operation with a different set of limits. If a vehicle is configured for both cab and remote PTO control, a PMC Location Switch must be installed on the dash. This switch will determine which set of PTO Mode Features to apply and which control location to use.

PTO Mode Switch

PMC Location Switch

8

Peterbilt Motors Company

POWER TAKE-OFF (PTO)

8-7

MX PTO MODE FEATURES The following features and configurations are available when PTO Mode is active.

Cab Accelerator Configurations o Disable in PTO Mode o Torque Control (Automotive Style) o Speed Control o Enable in Remote PTO Mode

Log Time and Fuel in PTO Mode Disable Engine Idle Shutdown Timer (EIST) in PTO Mode PTO Mode Specific Engine Idle Shutdown Timer (EIST) Fan On in PTO Mode Adjustable PTO Engine Speed Governor Responsiveness (for light or heavy varying loads)

MX PTO MODE PROTECTIONS AND LIMITS The following protections and limits are available when PTO Mode is active. Protections and limits are active when PTO Mode is active and will continue to be active until PTO Mode is no longer active.

Max Vehicle Speed Max Engine Torque Max Engine Speed Accelerator Controlled Max Engine Speed Switch Controlled Min Engine Speed Max Rate of Engine Speed Change

8

Peterbilt Motors Company

POWER TAKE-OFF (PTO)

8-8

MX PTO SPEED CONTROL (PSC) FEATURES PTO Mode must be active prior to using PTO Speed Control (PSC) to control engine speed. PSC is available from both the cab station and remote station (see PTO Mode Control Location Section above). In the cab location, cruise control switches and PSC specific switches are used to control engine speed. Equivalent remote station inputs are available (Reference Remote PMC Connections section below).

+ / - o Configurable to either command one unique preset when

+ is pressed and a second unique preset when - is pressed OR toggle through up to 6 presets.

Preset 1, 2 & 3 o 3 Dedicated Presets with the following configuration

options. Latch: Hold Preset Speed When Switch is Released Cancel: Cancel PSC When Switch is Released

o The Remote PTO Inputs for Presets 1, 2 & 3 can be configured to function when Cab PTO Mode is active

o In some applications, it may be useful to connect the Remote PTO Inputs for Presets 1, 2 & 3 to something other than a hand-operated switch. For example, the inputs can be configured to activate based off PTO engagement, hydraulic pressure or equipment movement.

Dash Switches

Dedicated Preset Switches

8

Peterbilt Motors Company

POWER TAKE-OFF (PTO)

8-9

MX PTO SPEED CONTROL INTERLOCKS PTO Speed Control Interlocks cancel PSC when active. There is an option to disable the accelerator when a PSC interlock is active. When a PSC interlock is active the engine speed will return to the Minimum Engine Speed in PTO Mode or the engine speed commanded by the accelerator if applicable. An active PSC interlock does not disable PMC protections and limits. The configurable PSC interlocks are listed below.

Clutch Pressed Park Brake NOT Set Transmission NOT in Neutral Service Brake (Configurable for Pressed or NOT Pressed) Custom Hardwired Interlock (Configurable Polarity)

A custom hardwired interlock input is available that will allow a body builder to create a customized interlock for their specific application. This interlock functions for both Cab and Remote Station PSC. Many types of switches such as hand-operated switches, hydraulic pressure switches, equipment position switches, or pressure plate switches can activate the interlock. The switch polarity is configurable which allows the body builder to choose the interlock state if the circuit fails. PTO SPEED CONTROL ICONS During PSC operation there will be icons on the digital display that indicate:

PSC Enabled (white icon) or Active (green icon) PSC Control Location (designed by Cab or Remote) PSC target engine speed when active

Cab PTO Active Remote PTO Active Cab PTO Enabled

8

Peterbilt Motors Company

POWER TAKE-OFF (PTO)

7-10

REMOTE PMC CONNECTIONS There are options to control PTO functionality from the following locations.

Engine Bay Hardwired option only RP1226 Connection in the Cab CAN bus connection only BOC/BOS Hardwired and CAN bus connections EOF Hardwired and CAN bus connections

There are options available for the body builder to specify controller speeds of 250 kbps or 500 kbps.

MX PTO CAN functionality may be accessed in the cab through the RP1226 connector and remotely through the body connectors K-CAN (E-3375-021) and B-CAN (DTM06-2S-EP10) Connectors. MX PTO hardwired functionality may be accessed in the engine bay or on the frame through optional 12-Way and 8-Way connectors

Pin-out information for the PTO connectors can be found in the Electrical Section

12-Way Deutsch Connector

8-Way Deutsch Connector

RP1226 Delphi Connector

8

Peterbilt Motors Company

POWER TAKE-OFF (PTO)

8-11

PTO MODE CONTROL FLOW CHARTS Cab Controls

Remote Hardwire Controls

Remote CAN Controls

Remote TSC1 CAN Controls

8

Peterbilt Motors Company

POWER TAKE-OFF (PTO)

8-12

MX PTO TROUBLESHOOTING GUIDE The following table is a trouble shooting guide for MX PTO functionality.

SYMPTOM POSSIBLE CAUSE SOLUTION

No green PTO cluster

telltale (PMC is not active)

PTO Mode Switch is not installed

Install and apply PTO Mode Switch

PTO engagement feedback is not provided to standard/optional

chassis module

Provide PTO engagement feedback to SCM (PTO#1) and/or OCM (PTO#2)

PTO ball switch is faulty Check that PTO ball switch is providing power or ground

PTO device is not engaging due to air supply solenoid or electric

signal not active

*Check EOA parameter settings in PVP *EOH PTOs are configured with parameter P816 *Check popups on driver display for interlock conditions (PTO engagements may be configured with park brake or PTO interlocks dependent on EOA parameter settings, these will result in popups on driver display)

PTO cluster telltale blinks intermittently

PTO engagement feedback connection is faulty

Check PTO engagement feedback to SCM/OCM

PMC switch connection is intermittent

Verify PMC switch connection (LIN jumper)

FIC or Cruise Control

appears instead of PTO Speed Control on driver

display

(when green PTO cluster telltale is present)

Both Cab and Remote control locations are configured in PVP, but PMC location switch is not

installed

Install PMC location switch, or select Cab or Remote control location in PVP

PTO/CC On/Off switch is not applied

Press/apply the PTO/CC On/Off switch on steering wheel or dashboard (cab controls) or remote station (pin 6 on P197) or via J1939 PTO SPN980 (remote controls)

CAB and/or Remote PMC is not configured

Enable CAB and/or Remote PMC in PVP and re-flash the VECU (PMC location switch is required if both control locations are configured)

8

Peterbilt Motors Company

POWER TAKE-OFF (PTO)

8-13

White PTO icon appears, but no green PTO Speed Control

icon on driver display

PTO Speed Control is not active

Activate PTO Speed Control using cab or remote Set/Resume, +/-, Dedicated Preset, or J1939 PTO inputs. See PTO Mode Control Flowcharts in this section.

PTO Speed Control switches are not enabled

Enabled PTO Speed Control switches P543 (Cab +/-), P610 (Cab Set/Resume), PXXX (Cab Dedicated Preset), P576 (Remote +/-), P611 (Remote Set/Resume, or P568/P569 (Remote Dedicated Preset)

PTO Speed Control interlock is violated

Check that enabled PTO Speed Control interlocks are satisfied for cab and/or remote controls: *Park brake *Service brake active or inactive *Neutral position *Custom interlock *SCR/DEF Level Inducement *Adaptive Cruise Control fault *ABS Braking Event *Stop Engine Lamp

Current PTO Speed Control location is not selected (when

configured for Cab AND Remote control)

Select CAB or REMOTE control location using PMC location switch

Green PTO Speed Control

icon on driver display appears, but engine speed

will not change

PMC engine speed slew rates are zero

Change engine speed slew rates to non-zero values

PMC engine torque limit is too low Increase engine torque limit

PSC Increment and/or decrement intervals are zero

PSC Presets are not enabled or are programmed to the Min Engine Speed in PTO Mode

Configure increment and/or decrement to non-zero values Enable PSC Presets and program preset values greater than the Min Engine Speed in PTO Mode

Cab accelerator pedal does not control engine speed

Cab accelerator control is not enabled

Enable the accelerator in Cab Control (P545), and/or Remote Control (P577) in PVP and re- flash the VECU

POWER TAKE-OFF (PTO)

Peterbilt Motors Company 8-14

8

Remote accelerator pedal does not control engine speed

PTO Mode Control is not active

Activate PTO Mode Control using PMC switch, provide PTO engagement feedback, or over the CAN bus

Remote accelerator control is not enabled

Enable the remote accelerator control (P578) in PVP and re- flash the VECU

PTO Speed Control interlock is violated

Check that enabled PTO Speed Control interlocks are satisfied: *Park brake *Service brake *Neutral position *Clutch position *Custom interlock *SCR/DEF Level Inducement *Adaptive Cruise Control *ABS Braking Event *Stop Engine Lamp

Remote accelerator pedal has not returned to the fully

released/zero position after entering PTO Mode Control

Calibrate/release remote accelerator to zero position

J1939 PTO CAN message does not affect PTO Speed

Control

Remote controls are not configured and/or selected

Configure Remote PTO Mode Control and ensure it is selected using PMC Location switch (if Cab and Remote are both enabled)

Body controller source address is not equal to 7d or

33d (0x21)

Configure body controller source address equal to 7d or 33d (0x21)

J1939 PTO SPN980 (PTO Governor Enable Switch) is

not equal to 1 (enabled)

Send J1939 PTO SPN 980 equal to 1

J1939 TSC1 CAN message does not affect PTO Speed

Control

Remote controls are not configured and/or selected

Configure Remote PTO Mode Control and ensure it is selected using PMC Location switch (if Cab and Remote are both enabled)

Body controller source address is not equal to 7d or

33d (0x21)

Configure body controller source address equal to 7d or 33d (0x21)

POWER TAKE-OFF (PTO)

Peterbilt Motors Company 8-15

8

J1939 TSC1 SPN695 (Override Control Mode) is

equal to zero

Send J1939 TSC1 SPN695 equal to 1, 2 or 3

J1939 TSC1 SPN3350 (TSC1 Control Purpose) is not 2

(PTO Governor)

Send J1939 TSC1 SPN3350 equal to 2

This page is intentionally left blank.