Contents

Peterbilt Model 220 Truck Body Builder Operator’s Manual PDF

1 of 86
1 of 86

Summary of Content for Peterbilt Model 220 Truck Body Builder Operator’s Manual PDF

RELEASE DATE 10/1/2017

Body Builders Manual Contents

Figures .................................................................................................................................................................................................................................................................... iii Tables ....................................................................................................................................................................................................................................................................... v Abbreviations....................................................................................................................................................................................................................................................... vi Section1 Introduction Section2Safety&Compliance

SAFETY SIGNALS 2-1 FEDERAL MOTOR VEHICLE SAFETY STANDARDS COMPLIANCE 2-2

Incomplete Vehicle Certication ........................................................................................... 2-2 Noise and Emissions Requirements ...................................................................................... 2-3

Section3 Dimensions FRAME HEIGHT 3-1 TURNING RADIUS 3-2 CAB TILT 3-3

Model 220 W/19.5 Tires ....................................................................................................... 3-3 Model 220 W/22.5 Tires ....................................................................................................... 3-3

OVERALL DIMENSIONS 3-4 Side View - Model 220 ......................................................................................................... 3-4 Front and Rear Views Model 220 ..................................................................................... 3-7

DETAIL VIEWS3-10 Left side: Chassis Heights Model 220 ............................................................................ 3-10 Components Locations Model 220 ....................................................................................... 3-12 Crossmember LocationsModel 220 ................................................................................ 3-14 Frame Rail Configurations ................................................................................................. 3-16 Battery Box, Fuel Tanks and Air Tanks Model 220 ...................................................... 3-17 Exhaust Canister Locations Model 220 ............................................................................ 3-18 Side View Model 220 clear rail package ......................................................................... 3-19 Reyco 79KB Single Rear Axle Hendrickson HAS Single Rear Axle ............................. 3-20

TIRE DATA 3-20 FRAME AND CAB RELATED HEIGHTS 3-20 GROUND CLEARANCES 3-20 PTO CLEARANCES 3-21

Section4Exhaust & Aftertreatment EXHAUST AND AFTERTREATMENT INFORMATION 4-1

General Guidelines for DEF System ..................................................................................... 4-3 Installation Requirements and Dimensions for DEF System ................................................. 4-3 Measurement Reference Points ............................................................................................. 4-4 Routing to the Dosing Module (Injector) .............................................................................. 4-5

GENERAL EXHAUST INFORMATION 4-6 Section5 Frame Layouts and Body Mounting

FRAME LAYOUTS 5-1 Visual Index .......................................................................................................................... 5-1

CRITICAL CLEARANCES 5-4 Rear Wheels and Cab ............................................................................................................ 5-4 Body Mounting Using Brackets ............................................................................................ 5-5 Frame Sill .............................................................................................................................. 5-5 Brackets ................................................................................................................................. 5-6 Mounting Holes ..................................................................................................................... 5-6 Frame Drilling ....................................................................................................................... 5-7 Hole Location Guidelines ...................................................................................................... 5-7

BODY MOUNTING USING UBOLTS 5-7 Spacers .................................................................................................................................. 5-7

REAR BODY MOUNT 5-9 i

Body Builders Manual Contents

Section6 Frame Modications FRAME MODIFICATIONS 6-1

Introduction ..................................................................................................................................... .6-1 DRILLING RAILS .......................................................................................................................................... 6-1 MODIFYING FRAME LENGTH ................................................................................................................... 6-1 CHANGING WHEELBASE ........................................................................................................................... 6-1 CROSSMEMBERS ......................................................................................................................................... 6-2 TORQUE REQUIREMENTS .............................................. ......................................................................... 6-3 WELDING 6-4

Section7 Electrical ELECTRICAL INTRODUCTION .................................................................................................................. 7-1 ELECTRICAL CIRCUITS .............................................................................................................................. 7-1

Capacity........................................................................................................................................... .7-1 Data Bus Communication ............................................................................................................... 7-2

CAB/CHASSIS INTERFACE 7-3 The EJB (Electrical Junction Box) .................................................................................................. .7-3

CONTROLLERS 7-6 DASH CONTROLS 7-7 MODEL 220 PTO WIRING INFORMATION 7-11

Appendix A Vehicle Identication VEHICLE IDENTIFICATION NUMBER ..................................................................................................... A-1

VIN Location .................................................................................................................................. A-1 Chassis Number Locations .............................................................................................................. A-1

CERTIFICATION LABELS ............................................................................................................................ A-2 Components and Weights Label ...................................................................................................... A-2 Tire/Rim and Weight Rating Data Label ......................................................................................... A-2 Incomplete Vehicle Certication Label ........................................................................................... A-2

COMPONENT IDENTIFICATION ................................................................................................................ A-3 Engine Identication ....................................................................................................................... A-3 Transmission Identication ............................................................................................................. A-4 Front Axle Identication ................................................................................................................. A-4 Rear Axle Identification .................................................................................................................. A-4

Appendix B Weight Distribution INTRODUCTION ........................................................................................................................................... B-1

Abbreviations .................................................................................................................................. B-1 CALCULATIONS .......................................................................................................................................... B-2

Weight Distribution without Body .................................................................................................. B-2 Weight Distribution with Body ....................................................................................................... B-4 Chassis Weights .............................................................................................................................. B-4 Weight Distribution Analysis .......................................................................................................... B-8 Body Length .................................................................................................................................... B-8

ii

Figures

Figure 2-1 Incomplete Vehicle Certification Document ........................................................................................ 2-2 Figure 2-2 Locations of Certification Labels Drivers Door & Frame ............................................................... 2-2 Figure 3-1.1 Side View Model 220 W/19.5 Tires Cab tilt Height and Pivot location Measurement ................ 3-3 Figure 3-1.2 Side View Model 220 W/22.5 Tires Cab tilt Height and Pivot location Measurement ................ 3-3 Figure 3-2.1 Side View Model 220 W/19.5 Tires Height and Length Measurement ......................................... 3-4 Figure 3-2.2 Side View Model 220 W/19.5 Tires Height and Length Measurement ......................................... 3-6 Figure 3-3.1 Front & Rear View Model 220 ..................................................................................................... 3-7 Figure 3-3.2 Model 220 Laden 22.5 Tires Front view: Width & Ground clearance Measurements: inches(mm) 3-8 Figure 3-3.3 Model 220 Laden 19.5 Tires Front view: Width & Ground clearance Measurements: inches(mm) 3-8 Figure 3-3.4 Model 220 Laden Rear view: Width & Ground clearance Measurements: inches(mm) .................... 3-9 Figure 3-4.1 Cab Floor: Side View, Left Side w/ 19.5 Tires ................................................................................. 3-10 Figure 3-4.2 Cab Floor: Side View, Left Side w/ 22.5 Tires ................................................................................. 3-11 Figure 3-5.1 Model 220 W/22.5 Tires, Battery Box, Fuel Tank, Air Tank, DEF Tank and Crossmember

Location Measured From Front Axle: inches (mm) .............................................................................. 3-12 Figure 3-5.2 Model 220 W/22.5 Tires, Battery Box, Dual Fuel Tanks, Air Tank, DEF Tank, and Crossmember

Location Measured From Front Axle: inches (mm) .............................................................................. 3-12 Figure 3-5.3 Model 220 W/22.5 Tires, Short wheelbase, Air tanks on RH side, Battery Box, Fuel Tanks,

DEF Tanks And Crossmember Location Measured From Front Axle: inches (mm) ........................... 3-13 Figure 3-5.4 Model 220 W/22.5 Tires, clear rail Package, Battery Box, Air Tank, Fuel tanks, DEF Tank,

And Crossmember Location Measured From Front Axle: inches (mm) .............................................. 3-13 Figure 3-6.1 Model 220 Crossmember Locations ................................................................................................ 3-14 Figure 3-6.2 Model 220 Crossmember Locations Measured from front Axle Centerline inches(mm) ................ 3-14 Figure 3-7 Model 220 Rail Measurements ............................................................................................................ 3-16 Figure 3-8 Model 220 Battery Box, Fuel Tank and Air Tanks Measurement mm (in) ........................................ 3-17 Figure 3-9.1 Model 220 Exhaust Measurements .................................................................................................. 3-18 Figure 3-9.2 Model 220 Exhaust Measurements .................................................................................................. 3-18 Figure 3-10.1 Side View - Model 220 CRP Laden Height and Length Measurement ........................................ 3-19 Figure 3-10.2 Model 220 Vertical Exhaust Measurements inches(mm) .............................................................. 3-19 Figure 3-11 Model 220 Reyco & Hendrickson Single Rear Axle Measurements ............................................... 3-20 Figure 3-12.1 PTO models installed on a 2000 Series Allison transmission ......................................................... 3-21 Figure 3-12.2 Model 220 PTO Clearances 1 of 2 .................................................................................................. 3-22 Figure 3-12.3 Model 220 PTO Clearances 2 of 2 .................................................................................................. 3-22 Figure 4-1.1 The DEF lines route to the after-treatment system ............................................................................. 4.1 Figure 4-1.2 The DEF lines route to the Engine Coolant ....................................................................................... 4.2 Figure 4-2 Measurement Location of DEF Supply Module (Pump) ...................................................................... 4-4 Figure 4-3 Measurement Location of DEF Dosing Module (Injector) ................................................................... 4-4 Figure 4-4 Orientation of Dosing Module .............................................................................................................. 4-5 Figure 4-5 Routing DEF Lines and DEF Trap ....................................................................................................... 4-5 Figure 4-6.1 Horizontal Exhaust Canister with Horizontal Tailpipe ....................................................................... 4-6 Figure 4-6.2 Top view of Horizontal Exhaust Canister with Horizontal Tailpipe .................................................... 4-6 Figure 4-6.3 Right view of Horizontal Exhaust Canister with Horizontal Tailpipe ................................................. 4-7 Figure 4-6.4 Back view of Horizontal Exhaust Canister with Horizontal Tailpipe ................................................. 4-7 Figure 4-7.1 Vertical Exhaust Canister with Horizontal Tailpipe ............................................................................ 4-8 Figure 4-7.2 Top view of Vertical Exhaust Canister with Horizontal Tailpipe ........................................................ 4-8 Figure 4-7.3 Right view of Vertical Exhaust Canister with Horizontal Tailpipe ...................................................... 4-9 Figure 4-7.4 Back view of Vertical Exhaust Canister with Horizontal Tailpipe ...................................................... 4-9

iii

Figures

Figure 5-1.1 Horizontal Exhaust Canister, RH horizontal tailpipe, LH BOC rectangular fuel tank, LH BOC rectangular DEF tank and RH BOC battery box ........................................................................ 5-2

Figure 5-1.2 Horizontal Exhaust Canister, RH horizontal tailpipe, Duel BOC rectangular fuel tank, LH BOC rectangular DEF tank and RH BOC battery box .................................................................. 5-2

Figure 5-1.3 Vertical Exhaust Canister, BOC Vertical tailpipe, LH BOC rectangular fuel tank, LH BOC rectangular DEF tank and BOC battery box ............................................................................... 5-3

Figure 5-2 Minimum Clearance between Top Of Rear Tires And Body Structure Overhang ............................... 5-4 Figure 5-3 Minimum Back of Cab Clearance ........................................................................................................ 5-4 Figure 5-4 Spacer between Frame Sill and Body Rail - Rubber or Plastic ............................................................. 5-6 Figure 5-5. High Compression Spring between the Mounting Bolt and Upper Bracket ........................................ 5-6 Figure 5-6 Rubber Spacers between Brackets ........................................................................................................ 5-6 Figure 5-7 Hole Locations Guidelines for Frame Rail and Bracket ....................................................................... 5-6 Figure 5-8 Crossmember-Gusset Hole Pattern Requirements. [inches(mm)] ......................................................... 5-7 Figure 5-9 Acceptable U-Bolt Mounting with Wood and Fabricated Spacers ....................................................... 5-8 Figure 5-10 Clearance Space for Air Lines and Cables .......................................................................................... 5-8 Figure 5-11 Example of Fishplate Bracket at Rear End of Body, used with U-Bolts ............................................ 5-9 Figure 6-1 Wheelbase Customization ..................................................................................................................... 6-1 Figure 6-2 Crossmember Added When Distance Exceeds 60 Inches (1524 mm) .................................................. 6-2 Figure 7-1 Data Bus Communication Architecture ................................................................................................ 7-2 Figure 7-2.1 Electrical Junction Box Location....................................................................................................... 7-3 Figure 7-2.2 Inside View - Electrical Junction Box Location ................................................................................ 7-3 Figure 7-3 LF Euro 6 Cab Interface Names ........................................................................................................... 7-4 Figure 7-4 Controllers ............................................................................................................................................ 7-6 Figure 7-5.1 Dash Controls-1 ................................................................................................................................. 7-7 Figure 7-5.2 Dash Controls-2 ................................................................................................................................. 7-7 Figure 7-6.1 Power Distribution Center ................................................................................................................. 7-8 Figure 7-6.2 Power Distribution Center (Chassis) .................................................................................................. 7-9 Figure 7-7 Body Builder 9 Pin Connector ............................................................................................................ 7-10 Figure 7-8.1 Typical PTO Wiring for Euro 6 LFNA 12V PTO Solenoid .......................................................... 7-12 Figure 7-8.2 Typical PTO Wiring for Euro 6 LFNA 24V PTO Solenoid ......................................................... 7-13 Figure 7-9 A 12-pin Deutsch connector and remote PTO Controls ..................................................................... 7-14 Figure A-1 Vehicle Identification Number (VIN) ................................................................................................ A-1 Figure A-2 Drivers Door and Door Frame Label ................................................................................................. A-2 Figure A-3 Engine Identication Location ............................................................................................................ A-3 Figure A-4 Front Axle Identication .................................................................................................................... A-4 Figure A-5 Rear Axle Identication ...................................................................................................................... A-4 Figure B-1 Balanced Load: CGf 100 in. from front axle ...................................................................................... B-2 Figure B-2 Unbalanced Load: CGf 133 In. From Front Axle ............................................................................... B-3 Figure B-3 Balanced Body Unloaded: CGf 184.7 in. (4691.45 mm) from front axle .......................................... B-5 Figure B-4 Liftgate Example: CGf 322.2 in (8183.9 mm) from front axle ........................................................... B-5 Figure B-5. Balanced Body Loaded: CGf 184.7 in (4691.45 mm) from front axle...B-7

iv

Tables

Table: Abbreviations Used ...................................................................................................................................... vi Table 3-1 Frame Height ........................................................................................................................................... 3-1 Table 3-2 Turning Radius ........................................................................................................................................ 3-2 Table 3-3 Cab Tilt Height ........................................................................................................................................ 3-3 Table 3-4 Cab Pivot Location .................................................................................................................................. 3-3 Table 3-5 Overall Dimensions ................................................................................................................................. 3-5 Table 3-6.1 Tires-Laden Ground clearance W/22.5 Tires ....................................................................................... 3-8 Table 3-6.2 Tires-Laden Ground clearance W/19.5 Tires ....................................................................................... 3-8 Table 3-7.1 Battery Box Step and Cab Floor Measurements w/ 19.5 Tires .......................................................... 3-10 Table 3-7.2 Battery Box Step and Cab Floor Measurements w/ 22.5 Tires .......................................................... 3-11 Table 3-8 Floor to Frame Measurements ............................................................................................................... 3-11 Table 3-9.1 Model 220 Crossmember Location Measured From Front Axle Centerline ...................................... 3-14 Table 3-9.2 Model 220 Crossmember Location Measured From Front Axle Centerline for Clear Rail Package . 3-15 Table 3-10 Frame Rail Strength Characteristics .................................................................................................... 3-16 Table 3-11 Model 220 Exhaust Location Measured From BOC inches (mm) ...................................................... 3-18 Table 3-12 Model 220 Exhaust Location Measured From BOC inches (mm) ...................................................... 3-18 Table 3-13 Model 220 Reyco & Hendrickson Single Rear Axle: Ride Height Measurement ............................... 3-20 Table 5-1 Symbols ................................................................................................................................................... 5-1 Table 6-1 Customary Grade 8 UNF or UNC ........................................................................................................... 6-3 Table 6-2 U.S. Customary Grade 8 Metric Class 10.9 ......................................................................................... 6-3 Table 7-1 Additional Spare Circuits for Wiring ...................................................................................................... 7-9 Table 7.2 Body Builder 9 Pin Connector ............................................................................................................... 7-10 Table A-1. Model Year (Code) Designations ......................................................................................................... A-1 Table B-1. Model 220 Single Rear Axle Bare Chassis Tare Weights (no driver, no fuel) ................................. B-4 Table B-2.1. Model 220 Weight Distribution and Chassis Rating Calculation (sample) ....................................... B-7 Table B-3. Available Model 220 Body Lengths ..................................................................................................... B-9

v

Abbreviations

ABBREVIATIONS Throughout this section and in other sections as well, abbreviations are used to describe certain characteristics on your vehicle. The chart below lists the abbreviated terms used.

Abbreviations Used

vi

AE AXLE TO END AF FRAME RAIL OVERHANG LENGTH BEHIND REAR BFA FRONT BUMPER TO FRONT AXLE LENGTH BOC BACK OF CAB CA BACK OF CAB TO REAR AXLE LENGTH/CARGO AREA CA CAB TO AXLE CBOC CLEAR BACK OF CAB CGF CENTER GRAVITY OF LOAD FROM FRONT AXLE CH CAB HEIGHT CLA CENTER LINE OF AXLE CRP CLEAR RAIL PACKAGE DEF DIESEL EXHAUST FLUID DSOC DUAL SIDE OF CAB EFF CA USEABLE CARGO AREA EOF END OF FRAME FAX FRONT AXLE FOC FRONT OF CAB FOR FRONT OF RAIL HA HEIGHT AXLE L LOAD

LF LOAD FRONT

LHUC LEFT HAND UNDER CAB

LR LOAD REAR

OAL OVERALL VEHICLE LENGTH R ROOF

RHUC RIGHT HAND UNDER CAB

SLR STATIC LOAD RADIUS

SOC SIDE OF CAB

TL TOTAL LENGTH TOC TOP OF CLAMP

TOLC TOP OF LOWER CLAMP

TOR TOP OF RAIL

WB WHEELBASE LENGTH

Abbreviations

vii

ACH-W AUXILIARY CAB HEATER WEBASTO AEBS ADVANCED EMERGENCY BRELECTRONIC BRAKING SYSTEMAKING SYSTEM AGC-A AUTOMATIC GEARBOX CONTROL ALLISON ALS-S ALARM SYSTEM SCORPION ASTRONIC LITE AUTOMATED GEARBOX CONTROL ZF ASTE-MODULE ASTRONIC SELECTOR ECU ASTMULTI-SPEED AUTOMATED 12-SPEED GEARBOX AXM-F/AXM-R AXLE MODULATOR FRONT/REAR BBM BODYBUILDER MODULE

CDS-4 CENTRAL DOOR LOCKING DIP-5 DIGITAL INSTRUMENT PACK DNR DRIVE NEUTRAL REVERSE SWITCH DTCO DIGITAL TECHNOGRAPH E-MODULE AUTOMATED GEAR SELECTOR ZF EAS EXHAUST AFTER-TREATMENT SYSTEMN

EBS-3 ELECTRONIC BRAKING SYSTEM ECSDC6 EURO 6 CUMMINS ENGINE ECAS-4 AIR SUSPENSION

ELC EXTERNAL LIGHTING CONTROLLER

ELS EXTERNAL LIGHTING SWITCH

FMS FLEET MANAGEMENT SYSTEM

IMMO IMMOBILISER

LDWS LANE DEPARTURE WARNING SYSTEM

MTCO MECHANICAL TECHNOGRAPH

SAC

SMART AIR CONTROL

SAS STEERING ANGLE SENSOR

SWA STEERING WHEEL SWITCHES

TI-2 TELEPHONE INTERFACE

VIC3 VEHICLE INTELLIGENCE CENTRE 3

VGT VARIABLE GEOMETRY TURBOCHARGER

VSC VEHICLE STABILITY CONTROL

1-1

Section 1 Introduction

This manual provides body builders with appropriate information and guidelines useful in the body planning and installation process. This information will be helpful when installing bodies or other associated equipment.

This manual contains appropriate dimensional information, guidelines for mounting bodies, guidelines for modi- fying frames, electrical wiring information, and other information useful in the body installation process.

The intended primary users of this manual are body builders who install bodies and associated equipment on Model 220 Medium Duty vehicles. Dealers who sell and service the vehicle will also nd this information useful.

This Body Builders Manual can be very useful when specifying a vehicle, particularly when the body builder is involved in the vehicle denition and ordering process. Early in the process, professional body builders can often contribute valuable information that reduces the ultimate cost of the body installation. The DAVIE4 diagnostic tool is recommended for all Model 220s built with the push button transmission shifter. The DAVIE3 (XDc) tool should be used with all Model 220s built with the lever style transmission shifter. Both DAVIE4 and DAVIE3 should be connected to the blue, 16-pin OBD connector located on the passenger side of the dash. Contact your local Peterbilt dealer to utilize the DAVIE tools or order the required hardware and software.

This manual is not a maintenance manual or an operation manual. For chassis maintenance and repair information consult the PACCAR ServiceNet available in the Service

Department of the selling dealer or order a custom shop manual or parts catalog for your vehicle through your local dealer.

For chassis operating information consult the Operators Manual, included with each vehicle. It can also

be ordered from your local dealer.

2-1

Section 2 Safety & Compliance

SAFETY SIGNALS

We have put a number of alerting messages in this book. Please read and follow them. They are there for your protection and information. These alerting messages can help you avoid injury to yourself or others and help prevent costly damage to the vehicle.

Key symbols and signal words are used to indicate what kind of message is going to follow. Pay special attention to comments prefaced by WARNING, CAUTION, and NOTE. Please do not ignore an y of these alerts.

Warnings, Cautions, and Notes

WARNING: When you see this word and symbol, the message that follows is especially vital. It signals a potentially hazardous situation which, i f not avoided, could r e su l t in death or serious injury. This message will tell you what the hazard is, what can happen if you dont heed the warning, and how to avoid it.

Example:

WARNING! Be sure to use a circuit breaker designed to meet liftgate amperage requirements. An in- correctly specied circuit breaker could result in an electrical overload or re situation. Follow the liftgate installation instructions and use a circuit breaker with the recommended capacity.

CAUTION: Signals a potentially hazardous situation which, if not avoided, could result in minor or moderate injury or damage to the veh ic l e .

Example: CAUTION: Never use a torch to make a hole in the rail. Use the appropriate drill bit.

NOTE: Provides general information. For example, the note could warn you on how to avoid damaging your vehicle or how to drive the vehicle more efciently.

Example:

Note: Be sure to provide maintenance access to the battery box and fuel tank ll neck.

Please take the time to read these messages when you see them, and remember:

WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Signals a potentially hazardous situation which, if not avoided, could result in minor or moderate injury or damage to the vehicle.

NOTE Useful information that is related to the topic being discussed.

2-2

Section 2 Safety & Compliance

FEDERAL MOTOR VEHICLE SAFETY STANDARDS COMPLIANCE

As an Original Equipment Manufacturer (OEM), Peterbilt Truck Co. ensures that our products comply with all applicable U.S. or Canadian Federal Motor Vehicle Safety Standards. However, the fact that this vehicle has no fth wheel and that a Body Builder (Intermediate or Final Stage Manufacturer) will be doing additional modications means that the vehicle was in- complete when it left the build plant. See next section and Appendix A for additional information.

Incomplete Vehicle Certication

An Incomplete Vehicle Document is shipped with the vehicle, certifying that the vehicle is not complete. See Figure 21. In addition, afxed to the drivers side door frame or edge is an Incomplete Vehicle Certication label. See Figure 22.. For further information on Vehicle Certication and Identication, see APPENDIX A VEHICLE IDENTIFICATION or owners manual.

NOTE: These documents list the U.S. or Canadian Federal Motor Vehicle Safety Standard regulations that the vehicle complied with when it left the build plant. You should be aware that if you add, modify or alter any of the components or systems covered by these regulations, it is your responsibility as the Inter- mediate or Final Stage Manufacturer to ensure that the complete vehicle is in compliance with the particular regulations upon completion of the modications.

Figure 2-1. Incomplete Vehicle Certication

Document

Tire, Rim and Weight Rating Data label

Safety Mark (Canadian Registry Only)

Incomplete Vehicle Certication Label

U.S. EPA Noise Label (U.S. registered vehicles only)

Final Stage Manufacturer Label to be Installed by Final Stage Manufacturer

Chassis Serial Number

Major Components and Weights Label

Figure 2-2. Locations of Certication Labels - Drivers Door and Frame

As the Intermediate or Final Stage Manufacturer, you should retain the Incomplete Vehicle Document for your records. In addition, you should record and retain the manufacturer and serial number of the tires on the vehicle. Upon completion of the vehicle (installation of the body and any other modications), you should afx your certication label to the vehicle as required by Federal law. This tag identies you as the Intermediate or Final Stage Manufacturer and certies that the ve- hicle complies with Federal Motor Vehicle Safety Standards. (SeeFigure 22.) For Canadian nal stage manufacturers see:

http://www.gazette.gc.ca/index-eng.html and http://www.tc.gc.ca/eng/acts-regulations/menu.htm for the regulations. Or contact: Transport Canada Tower C, Place de Ville, 330 Sparks Street Ottawa, Ontario K1A 0N5 (613) 990-2309 TTY: 1-888-675-6863

2-3

Section 2 Safety & Compliance

Noise and Emissions Requirements

NOTE:

NOTE:

This truck may be equipped with a converter mufer unit in order to meet both noise and exhaust emissions requirements. Removal or tampering with the converter mufer will not improve engine per- formance. Also tampering is against the rules that are established by the U.S. Code of Federal Regu- lations and Environment Canada Regulations. The converter mufer may only be replaced with an approved part. Relocation of converter mufer will affect noise and emission performance. Contact the engine manu- facturer for any requirements and restrictions prior to any modications. In particular, there are re- quirements and restrictions for exhaust pipe materials and for maximum exhaust system lengths from turbo outlet to mufer inlet.

3-1

Section 3 Dimensions

Frame Height

Top of frame is the sum of the tires (SLR),the suspension, and the frame.

Table 3-1 Frame Height

Model Model 220 De-rated Frame 10 inches 10 inches Front Suspension

Rating 12K 10K Unladen 8.1 8.1 Laden 5.9 5.9 Rear Suspension HAS 210/230 Unladen 8.5 8.5 Laden 8.3 8.3 79KB 21,000# Unladen 9.18 9.18 Laden 6.75 6.75 Tires (SLR) Tire GVWR 245/70R 19.5 G N/A 15.5 26,720 265/70R 19.5 G N/A 15.9 30,990 255/70R 22.5 H N/A 17.2 31,300 275/70R 22.5 J 17.6 17.6 39,580 295/75R 22.5 G 18.8 18.8 35,050 11R 22.5 G 25.8 19.5 35,710

3-2

TURNING RADIUS Approximate turning radius specications for the Model 220 are listed (by wheelbase) in the following tables. Tables 3-2 Turning Radius and 3-3 Cab Tilt Height information for chassis with standard components. Optional components may give different results.

Table 3-2 Turning Radius

Model

Rear Axles

Wheelbase Range

Curb to Curb Est. Radius

Wall to Wall Radius Est.

Inch mm ft m ft m Model 220

Single

121 3073.4 17.5 5.3 23.5 7.2 142 3606.8 18.4 5.6 24.4 7.5 146

3708.4 19.40 5.9 25.40 7.7

156 35162.4 20.1 6.1 26.1 4.0 158 3962.4 20.50 6.2 26.50 8.1 164 4165.6 21.2 6.5 27.2 8.4 168 4267.2 21.7 6.6 27.7 8.5 170 4318 22.04 6.7 28.04 8.5 182 4622.8 23.36 7.1 29.36 8.9 194 4927.6 24.69 7.5 30.69 9.4

206 5232.4 26.01 7.9 32.01 9.8 218 5537.2 27.33 8.3 33.33 10.2 230 5842 29.13 8.9 35.13 10.7 242 6146.8 29.97 9.1 35.97 11.0

274 6959.6 33.5 13.1 39.35 15.5

Section 3 Dimensions

3-3

Section 3 Dimensions

CAB TILT

Model 220 W/19.5 Tires

Figure 3-1.1 Side View Model 220 W/19.5 Tires Cab Tilt Height and Pivot location Measurement

Model 220 W/22.5 Tires

Figure 3-1.2 Side View Model 220 W/22.5 Tires Cab Tilt Height and Pivot

location Measurement

Table 3-4 Cab Pivot location

Behind CAB Pivot location

Above FOF 44.5MM

WL 209MM

CTR-CTR 978MM

Table 3-3 Cab Tilt Height

CAB Tilt

Highest point inches (mm)

220 W/19.5 Tires 128 (3258.7)

220 W/22.5 Tires 132 (3355.2)

3-4

Section 3 Dimensions

OVERALL DIMENSIONS This section includes drawings of the base Model 220, which includes:

On the pages that follow, detail drawings show particular views of each component of the vehicle. They illustrate important measurements critical to designing bodies of all types. See the Contents at the beginning of the manual to locate the drawing you need.

Side View Model 220

Figure 3-2.1 Side View Model 220 Laden Height and Length Measurement

Overall Model 220 Dimensions:

1) FAX TO BOC = 11

2) O.A .Length = 52+WB+AF

3) Frame Length = 49+WB+AF

4) Effective CA = WB-24.3 (24.3 is from C/L of front axle to the air cleaner duct with considering a 5 body spacer)

3-5

Section 3 Dimensions

Side View - Model 220 Table 3-5 Overall Dimensions

*With 5 inch spacer.

Model Wheelbase (in)

FAX to BOC (in)

FAX to Back of Intake /

FAX to Back of Exhaust for 220**

(in)

Body Builder Useable

CA (in)

Overhang (in)

Cab to EOF (in)

Recommended Body Length (ft)

220 Horizontal

Exhaust *

146 11 25.3 120.7 72 192.7 16 158 11 25.3 132.7 72 204.7 17 164 11 25.3 138.7 72 210.7 18 168 11 25.3 142.7 72 214.7 18 170 11 25.3 144.7 72 216.7 18 178 11 25.3 152.7 72 224.7 18 182 11 25.3 156.7 84 240.7 20 194 11 25.3 168.7 96 264.7 22 206 11 25.3 180.7 108 288.7 24 218 11 25.3 192.7 120 312.7 26 230 11 25.3 204.7 120 324.7 27 242 11 25.3 216.7 120 336.7 28 274 11 25.3 248.7 120 368.7 30

220 Vertical Exhaust

121 11 31.3 89.7 72 155 10 142 11 31.3 110.6 72 176 13 146 11 31.3 114.6 72 180 14 156 11 31.3 124.6 72 190 15 158 11 31.3 126.6 72 192 15 164 11 31.3 132.6 72 198 16 168 11 31.3 136.6 72 202 16 170 11 31.3 138.6 72 204 16 178 11 31.3 146.6 88 228 18 182 11 31.3 150.6 84 228 18 194 11 31.3 162.6 96 252 20

206 11 31.3 174.6 108 276 22 218 11 31.3 186.6 120 300 24 230 11 31.3 198.6 132 324 26 242 11 31.3 210.6 144 348 27 274 11 31.3 242.6 160 396 30

3-6

Section 3

Dimensions

Figure 3-2.2 Side View Model 220 Laden Height and Length Measurement

Overall Model 220 Dimensions:

1) FAX TO BOC = 11

2) O.A .Length = 52+WB+AF

3) Frame Length = 49+WB+AF

4) Effective CA = WB-31.5

3-7

)

Front and Rear Views Model 220

Inches (mm)

Section 3 Dimensions

Figure 3-3.1 Front & Rear View Model 220

3-8

Section 3 Dimensions

Front and Rear Views Model 220

Table 3-6.1 Laden Ground Clearance W/22.5 Tires

Figure 3-3.2 Model 220 Laden 22.5 Tires Front View: Width and Ground Clearance Measurements: inches (mm).

Figure 3-3.3 Model 220 Laden 19.5 Tires Front View: Width and Ground Clearance Measurements: inches (mm).

TIRE SIZE SLR RADIATOR GROUND

275/22.5 17.6 7.7 295/22.5 18.8 8.9 11R/22.5 19.5 9.6

Table 3-6.2 Laden Ground clearance W/19.5 Tire

TIRE SIZE SLR RADIATOR GROUND

245/19.5 15.5 7.5 265/19.5 15.9 7.9

Table 3-6.2 Laden Ground Clearance W/19.5 Tire

TIRE SIZE SLR RADIATOR GROUND

245/19.5 15.5 7.5 265/19.5 15.9 7.9

3-9

Section 3 Dimensions

Front and Rear Views Model 220

Figure 3-3.4 Model 220 Laden Rear View: Width and Ground Clearance Measurements: inches (mm).

3-10

Section 3 Dimensions

Detail Views Left side: Chassis Heights Model 220

Figure 3-4.1 Cab Floor: Side View, Left Side w/ 19.5 Tires

Table 3-7.1. Battery Box Step and Cab Floor Measurements w/ 19.5 Tires

Position Model 220 19.5 Tires

Unladen Laden In mm In mm

A FUEL SUPPORT STEP 10.5 269 7.5 191

B FIRST STEP 16.6 421 13.2 336

C SECOND STEP 27.2 690 23.8 605

D CAB FLOOR 38.6 977 35.2 894

3-11

Section 3 Dimensions

3 Dimensions Detail Views

Left side: Chassis Heights Model220ction

3ions

Figure 3-4.2 Cab Floor: Side View, Left Side w/ 22.5 Tires

Table 3-7.2. Battery Box Step and Cab Floor Measurements w/ 22.5 Tires

Position Model 220 22.5 Tires

*Unladen Laden In mm In mm

A FUEL SUPPORT 15.8 401 14.3 363

B FIRST STEP 18.4 467 16.9 430 C SECOND STEP 32.7 830 31.2 794

D CAB FLOOR 41.4 1051 39.9 1013 Table 3-8 Floor to Top of Frame Measurements

Frame Heights LOADED inches (mm) *UNLOADED inches (mm) Front Axle Rear Axle Front Axle Rear Axle

Model 220 W/19.5 (15.6 SLR) 31 (787) 32.5(825) 36 .1(916) 35.6 (905)

Model 220 W/ 11R-22.5 (19.4 SLR)

34.8 (884) 36.3 (922) 39.1(992) 38.6(980)

* Unloaded Dimensions are estimated.

3-12

Section 3 Dimensions Detail Views

Components Locations Model 220

Figure 3-5.1 Model 220 W/22.5 Tires, Battery Box, Fuel Tank, Air Tank and DEF Tank Location Measured From Front Axle: inches (mm).

Figure 3-5.2 Model 220 22.5 Tires, Battery Box, Dual Fuel Tanks, Air Tank and DEF Tank Location

Measured from Front Axle: inches (mm).

3-13

Section 3 Dimensions

3 Dimensions

Figure 3-5.3 Model 220 22.5 Tires, Short Wheelbase, Air Tanks on the RH Side, Battery Box and DEF Tank

Location Measured from Front Axle: inches (mm).

Figure 3-5.4 Model 220 22.5 Tires, Clear Rail Package, Air Tanks, Battery Box and DEF Tank Location Measured from Front Axle: inches (mm).

3-14

Section 3 Dimensions Detail Views

Crossmember Locations Model 220

Figure 3-6.1 Model 220 Crossmember Locations

Figure 3-6.2 Model 220 Crossmember Location Measured From Front Axle Centerline inches (mm)

Composition of use

WB

inches (mm) First

Midship C/M

D IM A

Second Midship

C/M

D IM B

Second Fill in C/M

D IM C

Third Midship

C/M

D IM D

CLASS 6 CLASS7 WO CLEAR RAIL PACKAGE

146 (3708.4) 3463.4 NA NA NA 158 (4013.2) 3463.4 NA NA NA 164(4165.6) 3463.4 NA NA NA 168(4267.2) 3463.4 NA NA NA 170 (4318) 3463.4 NA NA NA 178(4521.2) 3463.4 NA NA NA 182 (4622.8) 3463.4 4257 7180.4 NA 194 (4927.6) 3463.4 4257 7518 NA 206 (5232.4) 3463.4 4257 7975.2 NA 218 (5537.2) 3463.4 4663 8432.4 NA 230 (5842) 3463.4 4975 8781 NA

242 (6146.8) 3463.4 5075 9085.8 NA 274(6959.6) 3463.4 4975 9898.6 6100

Table 3-9.1 Model 220 Crossmember Location Measured from Front Axle Centerline inches (mm)

3-15

Section 3 Dimensions

3 Dimensions

Composition

of use

WB

inches (mm) First

Midship C/M

D IM A

Second Midship

C/M

D IM B

Second Fill in C/M

D IM C

Third Midship

C/M

D IM D

CLASS 6 CLASS7

CLEAR RAIL PACKAGE

121 (3073.4) NA NA NA NA

142 (3606.8) 3043.3 NA NA NA

146 (3708.4) 3043.3 NA NA NA 156 (3962.4) 3183.3 NA NA NA

158 (4013.2) 3183.3 NA NA NA 164(4165.6) 3183.3 NA NA NA 168(4267.2) 3183.3 NA NA NA 170 (4318) 3323.3 NA NA NA 178(4521.2) 3043.3 4257 NA NA 182 (4622.8) 3043.3 4257 7180.4 NA 194 (4927.6) 3183.3 4397 7518 NA 206 (5232.4) 3183.3 4397 7975.2 NA 218 (5537.2) 3183.3 4663 8432.4 NA 230 (5842) 3463.3 4975 8781 NA

242 (6146.8) 3463.3 5075 9085.8 NA 274(6959.6) 3463.3 4975 9898.6 6100

Table 3-9.2 Model 220 Crossmember Location Measured From Front Axle Centerline for

Clear Rail Package inches (mm)

3-16

Section 3 Dimensions Frame Rail Configurations

Model 220

10-1/4 STEEL RAIL

Figure 3-7 Model 220 Rail Measurements Table 3-10 Frame Rail Strength Characteristics

RAIL STRENGTH

10.25 Rail (Per Rail)

Yield Strength, PSI 120,000 Section Modulus, in3 11.65 RBM, Lbs-Inch 1,398,664

3-17

Section 3 Dimensions

3 Dimensions Battery Box, Fuel Tanks and Air Tanks Model 220

Figure 3-8 Model 220 Battery Box, Fuel Tank and Air Tanks Measurement mm (in)

3-18

Section 3 Dimensions

Detail Views Exhaust Canister Locations Model 220

=

Figure 3-9.1 Model 220 Exhaust Measurements

Table 3-11 Model 220 Exhaust Location Measured From Front Axle in inches (mm)

Model A B C D E Model 220 54.3 (1378.3) 92.3 (2343.6) 101.3 (2572.2) 14.2 (360.7) 13.2 (360.7)

Figure 3-9.2 Model 220 Exhaust Measurements

Table 3-12 Model 220 Exhaust Location Measured From Outboard and Bottom of Rail inches (mm)

Model A B C D Model 220 6.6 (167) 4.9 (125.3) 13.6 (345) 13.9 (353.5)

3-19

Section 3 Dimensions

3 Dimensions Side View Model 220 clear rail package

Figure 3-10.1 Side View Model 220 CRP Laden Height and Length Measurement

Figure 3-10.2 Model 220 Vertical Exhaust Measurement inches (mm)

3-20

Section 3 Dimensions Reyco 79KB Single Rear Axle Hendrickson HAS Single Rear Axle

Figure 3-11 Model 220 Reyco & Hendrickson Single Rear Axle Measurements

Suspension Rating Laden Ride Height Unladen Ride Height

Reyco 79KB Single 21K 7.5" 9.0"

Hendrickson HAS 210L/230L 23K

8.3"

8.5"

Table 3-13 Model 220 Reyco & Hendrickson Single Rear Axle: Ride Height Measurements

TIRE DATA For dimensions of your particular tire, visit the manufacturer website.

FRAME AND CAB RELATED HEIGHTS The bottom of the frame rail (BOF) at the front and rear axle can be used as a reference point to estimate vertical heights. Use the following to calculate estimates for frame and cab related heights, such as top of frame rail, step height, top of exhaust pipe, etc.:

1.) Tire radius data from the manufacturer 2.) Front and rear suspension ride heights in this section 3.) Frame rail heights defined in this section if needed 4.) Component dimensions from bottom of rail defined in this section if needed

Note that there are many factors that will affect heights including, but not limited to, front and rear axle loading and tire pressure. Placement of frame components such as fuel tanks will affect loads on the front axle and rear axle, as well as distribution to the left and right sides of the vehicle. Heights calculated from this information are estimates only.

GROUND CLEARANCES To calculate estimates for ground clearance for mounted components using the underside of the bottom of the frame rail as a reference use the following:

1.) Tire radius data from the manufacturer 2.) Front and rear suspension ride heights in this section 3.) Component dimensions from bottom of rail defined in this section

Ground clearances, like height calculations, are affected by factors including, but not limited to, front and rear axle loading and tire pressure. Placement of frame components, such as fuel tanks, will affect loads on the front axle and rear axle, as well as distribution to the left and right side of the vehicle. Ground clearances calculated from this information are estimates only.

3-21

Section 3 Dimensions

PTO Clearances

The following visuals are provided to help or aid in determining PTO locations and clearances. For specific dimensions please work through your local Peterbilt dealer. Multiple PTOs are shown for layout purposes only. Power equipment, i.e., drive shafts & power pumps are not included. Body builders should select the appropriate Chelsea or Muncie 24V electric over air PTOs for their application and customer requirements.

NOTE: All installations are only RH side PTO locations shown below are for reference only.

In order to ensure the PTO area remains clear of air equipment, electrical and emissions equipment, Peterbilt recommends always ordering PTO controls, even when installing the PTO aftermarket. Contact your local dealer for assistance.

Below are shown example of PTO models installed on a 2000 Series Allison transmission:

Automatic Transmission Allison 2000:

Muncie PTO TG6S-A1BX Muncie PTO CS6-H3KP

Chelsea PTO Model 230-270 Chelsea PTO Model 442

Figure 3-12.1 PTO models installed on a 2000 Series Allison transmission

3-22

Section 3 Dimensions

Figure 3-12.2 Model 220 PTO Clearances 1 of 2

Figure 3-12.3 Model 220 PTO Clearances 2 of 2

4-1

Section 4 Exhaust & Aftertreatment

EXHAUST AND AFTERTREATMENT INFORMATION The following section is designed to give you information regarding the exhaust and after-treatment systems on Peterbilt chassis. All Peterbilts equipped with 2017 emission level engines will utilize Selective Catalyst Reduction (SCR). SCR is a process in which Diesel Exhaust Fluid (DEF) is injected into the exhaust downstream of the engine. DEF is converted to ammonia by the heat of the exhaust system. Inside of the SCR canister, a catalyst causes a chemical reaction between the ammonia and NOx, turning it into water and nitrogen. For more information on the specific details of how SCR works, please contact your local Peterbilt dealer.

On most Peterbilt chassis, the DEF Supply Module (or pump) is integrated into the DEF tank. Peterbilt does not allow relocation of this pump. The following schematic details how the DEF lines route to the after-treatment system.

Figure 4-1.1 The DEF lines route to the after-treatment system

4-2

Section 4 Exhaust & Aftertreatment

DEF will freeze at approximately 11 F (-12 C). In order to keep DEF from freezing, all tanks will be heated with engine coolant. The following schematic shows the routing of these lines. The coolant lines that run to and from the SCR system must not be tampered with, or used for a source of heat and/or cooling for other components on the chassis. It is critical that the system is not compromised in any manner.

Figure 4-1.2 The DEF lines route to the Engine Coolant

4-3

Section 4 Exhaust & Aftertreatment

General Guidelines for DEF System The installation of the DEF tank is a critical component of the SCR system. While Peterbilt does not recommend relocating the DEF tank, there are applications and body installations that will require it. The guidelines below must be strictly followed by any entity relocating the tank. Failure to follow the guidelines completely and accurately may result in engine shut down situations. Peterbilt offers a variety of DEF tank sizes to meet every application. The DEF tank volume is regulated by the E.P.A. Peterbilt advises against modifying the tank volume after the truck has been delivered from the factory.

Total DEF capacity must meet or exceed 6% of the useable fuel capacity on the truck. The calculation

to determine DEF capacity is: Minimum DEF Tank Volume = Useable Fuel Capacity (gal) x 0.06. Example: For a truck with 45 useable gallons of fuel, the equation is: DEF required = 45 x 0.06 = 2.7 gallons or more of DEF.

PACCAR-approved DEF hoses are required when retrofitting for system to function properly. The use of unapproved hoses for DEF lines will void warranty and may cause engine shut down situations. The DEF pump (or Supply Module) cannot be relocated from the DEF tank. In addition, the Medium Duty Rectangular DEF Tank that is used to meet clear back of cab requirements cannot be relocated. Installation Requirements and Dimensions for DEF System When relocating any DEF system components, the locations must meet the guidelines below. Failure to comply may result in non-conformance to EPA standards and engine shutdown.

DEF piping relative heights: In order to ensure proper functionality of DEF system, the height differences in the guidelines below must be followed during line routing and component placement.

When relocating the components the maximum pressure DEF hose length from Supply module to Dosing Module is 3 meters (118).

Maintain a minimum of 3 (76mm) clearance to shielded exhaust components when routing DEF lines to prevent possible melting. If the DEF tank is relocated the coolant lines will need to be modified. During this process, if the tank is moved forward on the chassis (ie closer to the engine), it is necessary to remove excess coolant lines and maintain the original routing path. If the tank is moved rearward on the chassis, the additional length of the cooling line required to complete the installation must be installed in a straight section of the existing coolant routing lines. This process will minimize the change in coolant flow by minimizing changes in restrictions. Increase in restriction occurs with excessive line length and bends. Work with your local Peterbilt dealer if you are unsure about the coolant line modifications.

4-4

Section 4 Exhaust & Aftertreatment

Measurement Reference Points For all relocation procedures, the measurement points referenced in the guidelines are taken from the following specific points: Supply Module: The supply module is commonly called a pump. The measurement point on the supply module is the top of the DEF fluid pressure line. See Figure 4-2.

Figure 4-2 Measurement Location of DEF Supply Module (Pump)

Dosing Module: The dosing module is commonly called an injector; this injector is located towards the center of the Exhaust Canister. The measurement point on the dosing module is the top of the DEF fluid pressure line. See Figure 4-3.

Figure 4-3 Measurement Location of DEF Dosing Module (Injector)

The following relocation guidelines are dependent on exhaust configuration and DEF tank type and location.

The Dosing Module should not need to be relocated, however if it is removed for any reason, it is critical that the module is reinstalled at the correct orientation. Figure 4-4 below illustrates the correct installation orientations. The angle references the vertical plane.

4-5

Section 4 Exhaust & Aftertreatment

Figure 4-4 Orientation of Dosing Module

Routing to the Dosing Module (Injector) It is important for the function of the dosing module to ensure that the dosing module is not routed downstream of DEF lines or components. If this is unavoidable (for example on RH under exhaust systems) or Horizontal (Series) Exhaust, a routing trap must be installed. A minimum of 12 of line length must be routed below the dosing module to catch any leftover DEF when system is purged.

Horizontal Exhaust Vertical Exhaust

Figure 4-5 Routing DEF Lines and DEF Trap

4-6

Section 4 Exhaust & Aftertreatment

GENERAL EXHAUST INFORMATION

Peterbilt will offer Horizontal and Vertical Exhaust Canister system on Model 220 chassis in 2017.

Figure 4-6.1 Horizontal Exhaust Canister with Horizontal Tailpipe

Figure 4-6.2 Top view of Horizontal Exhaust Canister with Horizontal Tailpipe

4-7

Section 4 Exhaust & Aftertreatment

Figure 4-6.3 Right view of Horizontal Exhaust Canister with Horizontal Tailpipe

Figure 4-6.4 Back view of Horizontal Exhaust Canister with Horizontal Tailpipe

4-8

Section 4 Exhaust & Aftertreatment

GENERAL EXHAUST INFORMATION

Figure 4-7.1 Vertical Exhaust Canister with Vertical Tailpipe

Figure 4-7.2 Top view of Vertical Exhaust Canister with Vertical Tailpipe

4-9

Section 4 Exhaust & Aftertreatment

Figure 4-7.3 Right view of Vertical Exhaust Canister with Vertical Tailpipe

Figure 4-7.4 Back view of Vertical Exhaust Canister with Vertical Tailpipe

5-1

Section 5 Frame Layouts and Body Mounting

FRAME LAYOUTS The dimensions in the frame layout section are intended to aid in layout of the chassis, and to help determine the best possible combination of fuel tanks, battery boxes, Exhaust Canister, and Diesel Exhaust Fluid (DEF) tank. For your application, the layouts focus on the under cab area, with appropriate dimensional information in- cluded for pertinent back of cab components. Not all optional equipment is included in this section; additional components may be placed on the rail behind components shown. The Back of Cab components are shown primarily for reference. For more specific requirements, work with your local Peterbilt Dealer. Please read the instructions carefully. The following dimensions are consistent across the entire section to aid in the comparison of one layout option versus another.

The visual index that follows will give you a quick overview of the layout that is included. Visual Index

Table 5-1 Symbols

Symbol Description

Horizontal Exhaust

Canister

Vertical Exhaust Canister

Battery Box

Air Dryer

DEF Tank

Fuel Tank

5-2

Section 5 Frame Layouts and Body

Mounting

Figure 5-1.1 Horizontal Exhaust Canister, RH horizontal tailpipe, LH BOC rectangular fuel tank, LH BOC

rectangular DEF tank, and RH BOC battery box

Figure 5-1.2 Horizontal Exhaust Canister, RH horizontal tailpipe, Duel BOC rectangular fuel tanks, LH BOC

rectangular DEF tank, and RH BOC battery box

5-3

Section 5 Frame Layouts and Body

Mounting

Figure 5-1.3 Vertical Exhaust Canister, BOC Vertical tailpipe, LH BOC rectangular fuel tank, LH BOC

rectangular DEF tank and BOC battery box

5-4

Section 5 Frame Layouts and Body

Mounting

CRITICAL CLEARANCES Rear Wheels and Cab

CAUTION: Insufficient clearance between rear tires and body structure could cause damage to the body during suspension movement. Allow at least 8 inches clearance (See Figure 5-2.)

Normal suspension movement could cause contact between the tires and the body. To prevent this, mount the body so that the minimum clearance between the top of the tire and the bottom of the body is 8 inches (203 mm). This should be measured with the body empty. See Figure 5-2.

Figure 5-2 Minimum Clearance Between Top Of Rear Tires And Body Structure Overhang.

The true distance from the centerline of the front axle to the back of the cab is 11 inches for Model 220 (279.4mm). It is recommended that the leading edge of the body be mounted a minimum of 4 inches (102mm) behind the cab. The result is a minimum backofcab clearance of 15 inches for Model 220 (381mm) from the front axle to the leading edge of the body(A).

CAUTION: Maintain adequate clearance between back of cab and the front (leading edge) of mounted body. See Figure 5-2.

Note: Be sure to provide maintenance access to battery box and fuel tank ll neck.

See SECTION 3 DIMENSIONS for further details on dimensions and clearances. Also, see APPENDIX B WEIGHT DISTRIBUTION for explanation of backofcab (BOC)/CA calculations.

A

Figure 5-3 Minimum Back of Cab Clearance

5-5

Section 5 Frame Layouts and Body

Mounting

WARNING:If the frame rail anges are modied or damaged, the rail could fail prematurely and cause an accident. When mounting a body to the chassis, DO NOT drill holes in the upper or lower ange of the frame rail. Mount the body using body mounting brackets or Ubolts.

Body Mounting Using Brackets

CAUTION: Always install a spacer between the body subframe and the top ange of the frame rail. Failure to do so could result in corrosion due to dissimilar materials.

Installation of a spacer between the body subframe and the top ange of the frame rail will help prevent premature wear of the components due to chang or corrosion.

Frame Sill If the body is mounted to the frame with brackets, we recommend that the frame sill spacer be made from a strip of rubber or plastic (delrin or nylon). These materials will not undergo large dimensional changes during periods of high or low humidity. The strip will be less likely to fall out during extreme relative motion between body and chassis. See Figure 5-4.

5-6

Section 5 Frame Layouts and Body

Mounting

Body Subframe (Rail)

Chassis Frame (Rail) Sill

Spacer

Brackets

Figure 5-4 Spacer Between Frame Sill and Body Rail - Rubber or Plastic

When mounting a body to the chassis with brackets, we recommend designs that offer limited amount of relative move- ment, bolted securely but not too rigid. Brackets should allow for slight movement between the body and the chassis. For instance, Figure 55 shows a high compression spring between the bolt and the bracket.

Figure 5-5 High Compression Spring Between the Mounting Bolt and Upper Bracket

Figure 5-6 Rubber Spacer Between Brackets

Another possibility is mounting a rubber spacer between the brackets. See Figure 5-6. These designs will allow relative movement between the body and the chassis during extreme frame racking situations. Extreme frame racking and mountings that are too rigid, could cause damage to the body. This is particularly true with tanker installations.

Mounting Holes When installing the lower bracket on frame rails the mounting holes in the chassis frame bracket and frame rail must comply with the general spacing and location guidelines illustrated in Figure 5-7. The hole diameter should not exceed the bolt diam- eter by more than .060 inches (1.5 mm).

Upper Frame Flange

Lower Frame Flange

A A or B Equal to or Greater Than 2 Inches (50 mm)

Figure 5-7 Hole Locations Guidelines for Frame Rail and Bracket

5-7

Section 5 Frame Layouts and Body

Mounting

Figure 5-8 Crossmember-Gusset Hole Pattern Requirements. [inch(mm)]

Frame Drilling

WARNING: When mounting a body to the chassis, DO NOT drill holes in the upper or lower flange of the frame rail. If the frame rail flanges are modified or damaged, the rail could fail prematurely and cause an accident. Mount the body using body mounting brack- ets or Ubolts.

WARNING: Use care when drilling the frame web so the wires and air lines routed inside the rail are not damaged, Failure to do so could cause an inoperable electrical or air sys- tem circuit.

WARNING: Do not drill new holes any closer than 2 inches (50 mm) to existing holes. Frame drilling affects the strength of the rails.

Hole Location Guidelines Holes must be located from the ange as indicated in Figure 5-7. They must be no closer than 2 inches (50 mm) to each other.

Note: If your design permits placement of body mounting brackets at crossmember locations, you can use the crossmember gusset bolt holes for body mounting. See Figure 5-8

BODY MOUNTING USING UBOLTS Spacers

If the body is mounted to the frame with Ubolts, use a hardwood sill [minimum 1/2 inch (12 mm) thick] between the frame rail and body frame to protect the top surface of the rail ange.

5-8

Section 5 Frame Layouts and Body

Mounting

WARNING! Do not allow the frame rails or anges to deform when tightening the Ubolts. It will

weaken the frame and could cause an accident. Use suitable spacers made of steel or hardwood on the inside of the frame rail to prevent collapse of the frame anges.

Use a hardwood spacer between the bottom ange and the Ubolt to prevent the Ubolt from notching the frame ange. See Figure 5-9.

Body Structure

Wood Sill 0.5 (12mm) Minimum

Truck Frame

Frame Rail Spacer (Fabricated Steel or

Hardwood)

U-Bolt

U-Bolt Spacer (Hardwood)

Figure 5-9. Acceptable U-Bolt Mounting with Wood and Fabricated Spacers

WARNING!

CAUTION:

Do not allow spacers and other body mounting parts to interfere with brake lines, fuel lines, or wiring harnesses routed inside the frame rail. Crimped or damaged brake lines, fuel lines, or wir- ing could result in loss of braking, fuel leaks, electrical overload or a re. Carefully inspect the in- stallation to ensure adequate clearances for air brake lines, fuel lines, and wiring. See Figure 510.

Mount Ubolts so they do not chafe on frame rail. Failure to do so could result in premature wear of the U-bolt or frame rail.

Frame Rail

Air Lines and Wiring Harness

Check Clearance Space for Air

Lines and Wiring

U-Bolt

Frame Rail Spacer (Hardwood or Steel

U-Bolt Spacer

Figure 5-10. Clearance Space for Air Lines and Cables

5-9

Section 5 Frame Layouts and Body

Mounting

WARNING! Do not notch frame rail anges to force a Ubolt t. Notched or damaged frame anges could re- sult in premature frame failure. Use a larger size Ubolt. Use a hardwood spacer as shown in Fig- ure 5-9.

REAR BODY MOUNT

When Ubolts are used to mount a body, we recommend that the last body attachment be made with a shplate bracket. See Figure 5-11. This provides a rm attaching point and helps prevent any relative fore or aft movement between the body and frame.

Body Structure

Frame Rail

Figure 5-11 Example of Fishplate Bracket at Rear End of Body, used with U-Bolts

6-1

Section 6 Frame Modifications

FRAME MODIFICATIONS INTRODUCTION

Peterbilt offers customer specified wheelbases and frame overhangs. So, in most cases frame modifications should not be necessary.

However, some body installations may require slight modifications, while other installations will require extensive modifications. Sometimes an existing dealer stock chassis may need to have the wheelbase changed to better fit a customers application. The modifications may be as simple as modifying the frame cutoff, or as complex as modifying the wheelbase.

DRILLING RAILS

If frame holes need to be drilled in the rail, see SECTION 4 BODY MOUNTING for more information.

MODIFYING FRAME LENGTH

The frame overhang after the rear axle can be shortened to match a particular body length. Using a torch is acceptable; however, heat from a torch will affect the material characteristics of the frame rail. The affected material will normally be confined to within 1 to 2 inches (25 to 50mm) of the flame cut and may not adversely affect the strength of the chassis or body installation.

CHANGING WHEELBASE

Changing a chassis wheelbase is not recommended. Occasionally, however, a chassis wheelbase will need to be shortened or lengthened. Before this is done there are a few guidelines that should to be considered.

WARNING! When changing the wheelbase, be sure to

follow the driveline manufacturers recommendations for driveline length or angle changes. Incorrectly modified drivelines can fail prematurely due to excessive vibration. This can cause an accident and severe personal injury.

Before changing the wheelbase, the driveline angles of the proposed wheelbase need to be examined to ensure no harmful vibrations are created. Consult with the driveline manufacturer for appropriate recommendations.

Before the rear suspension is relocated, check the new location of the spring hanger brackets. The new holes for the spring hanger brackets must not overlap existing holes and should adhere to the guidelines in the FRAME DRILLING section of this manual.

When shortening the wheelbase, the suspension should be moved forward and relocated on the original rail. The rail behind the suspension can then be cut to achieve the desired frame overhang. See FIGURE 6-1.

Figure 6-1 Wheelbase Customization

6-2

Section 6 Frame Modications

CROSSMEMBERS

After lengthening a wheelbase, an additional crossmember may be required to maintain the original frame strength. Con-tact Dealer for crossmember locations.

The maximum allowable distance between the forward suspension crossmember and the next crossmember forward is 47.2 inches (1200 mm). If the distance exceeds 47.2 inches (1200 mm) after the wheelbase is lengthened, add a crossmember between them. See Figure 5-4. See Figure 4-7 on page 4-3 for crossmember hole patterns. FIGURE 6-2. Crossmember Spacing Requirements FRAME MODIFICATIONS Peterbilt Motors Company 6-2

Figure 6-1 Crossmember Added When Distance Exceeds 60 Inches (1524 mm)

6-3

Section 6 Frame Modifications

TORQUE REQUIREMENTS

Torque values apply to fasteners with clean threads, lightly lubricated, with hardened steel washers, and nylon-insert nuts.

Table 6-1 Customary Grade 8 UNF or UNC

Fastener Torque

Size Nm Lb-Ft

5/16 22-30 16-22

3/8 41-54 30-40

7/16 75-88 55-65

109-122 80-90

9/16 156-190 115-140

5/8 224-265 165-195

394-462 290-340

7/8 517-626 380-460

1 952-1129 800-830

1-1/8 1346-1591 990-1170

1-1/14 1877-2217 1380-1630

Table 6-2 U.S. Customary - Grade 8 Metric Class 10.9

Fastener Torque

Size Nm Lb-Ft

M6 9-15 7-11

M8 23-31 17-23

M10 33-43 24-32

M12 75-101 55-75

M14 134-164 99-121

M16 163-217 120-160

M20 352-460 260-340

Section 6 Frame Modifications

WELDING

The frame rails are heat treated and should not be welded. The high heat of welding nullifies the special heat treatment of the rails, greatly reducing the tensile strength of the frame rail. If a frame member becomes cracked from overloading, fatigue, surface damage or a collision, the only permanent repair is to replace the damaged frame member with a new part.

The following information is provided (for temporary emergency repair). Prior to welding a cracked frame rail, the area should be beveled (V'd out) to allow for a better weld. To prevent spreading of the crack, a 7 to 9 mm (1/4 in. to 3/8 in.) diameter hole should be drilled at the end of the crack. Widen the crack along its full length by using two hack saw blades together. When welding steel frames use the shielded arc method. When welding aluminum frames use either the tungsten inert gas (TIG) or consumable electrode method. Be sure to obtain full weld penetration along the entire length of the crack.

BWeEfoLrDeINwG PRECAUTION2345 1e..... ldi T n EDDDm iig unoa ss rsx cco nnui oonormo nnef v fuu nnt esk eemh hee cciatt c yttw l .h aate ellehl llsde eEEwc lg iCCeu t rcr h oMMtru r e eicon lc nro e dt acnleac tncnrnoe oogdnic nnnnt in m coeeeric e ns cgtii t.nriomo gon iuu nnfnsm e odt s rr o, ists tthtk huhe edt e ow ffvooed elrl l ad hotiehm wcrel i a ei n sgg gbreao apse turtl enceel crdco ia t esro u i sfe t c i.tat ohlo nect s ohw s eme hlp o wdoi u en l nl dgden bpptr e osoi o nbot ben s a.t e sh r ep ve ovs d es . hiibcllee..This ensuresBosch ABS and Wabco ABS: Disconnect ECU.

PRECAUTIONS BBeeffoorree wweellddiinngg,, ddiissccoonnnneecctt tthhee naletegrantiavteortet rermmininalalbsa.tFtearilyurceabt loed.o so could result in damage tot t Sp Tr h :au oerA ctp v k Ls r, o L elwa tviE a lnelL g dnbE etbeC rde e daTs g amRu u mr la O a eag t Ng et o I he rt C ado a t Ei neft lN h d ce / e Gu ocrt r I wrrN ie a ec l E ln tadt e S li r nem n gq a uu t sgi o trp r op .muanesdnstl,tehdraiosducigoshncntohencentmebciatntetdeorrtydoectrhatebolfecrsaobmmeepfl.oerBteeeatarhricengcwisrecladuniitnd.gotohnera

6-4

7-1

Section 7 Electrical

ELECTRICAL Introduction

Through the use of an optional body harness and additional spare circuits, we have reduced the complexity associated with adding common circuits to a body installation.

Note: The most common circuits that body builders may need are pre-connected to this optional wiring harness.

.

ELECTRICAL C I R C U I T S Capacity WARNING! Do not install an electrical circuit that requires more amperage (electrical capacity) than what is

available in the specic chassis circuit. An overloaded circuit may cause severe damage. Compare the amperage requirements of the new circuit to the electrical current capacity of the existing chassis circuit before adding the body or other equipment.

7-2

Section 7 Electrical

Data Bus Communication

WARNING! The Data Buss for the communication between electronic control units must adhere to the guidelines outlined under SAE J1939 documentation. The Euro 6 LFNA Model has multiple CAN(Controller Area Networks) busses and care must be taken if an interface is required. Please contact the local Paccar Service Representative for appropriate assistance and information.

Figure 7-2 Data Bus Communication Architecture

7-3

Section 7 Electrical

Cab/Chassis Interface:

The EJB(Electrical Junction Box) Location: Firewall(opposite side of steering column)

Figure 7-3.1 Electrical Junction Box Location

Figure 7-2.2 Inside View - Electrical Junction Box Location EJB Connector Identifiers: Front View = Front of Vehicle view Rear View = Passenger Seat view (see next page for clarity)

7-4

Section 7 El Electrical

Figure 7-3 LF Euro 6 Cab Interface Names

The EJB contains both 24VDC and 12VDC circuitry for the vehicle. Contact the local Paccar Service Representative for the appropriate circuitry identification if access to this panel is required.

7-5

Section 7 Electrical

7-6

Section 7 Electrical

Controllers

Figure 7-4 Contollers The EJB is the electrical load center for the cab. The cab and the associated controllers listed operate on 24VDC. The 12/24 VDC converter located in the battery box supplies the necessary power requirements. The ELC(Electronic Lighting Controller) supplies the signals for all the lighting functions(24VDC in cab and roof) and its outputs are used to activate 24VDC relays in the electrical load center mounted in the battery box. These relays in turn control all the 12VDC exterior lighting. The VIC(Vehicle Intelligence Center) is the main controller and communicator for the vehicle. The EBS(Electronic Braking System) is the controller for the EoA(Electric over Air) braking system. The OBD plug in the image above is the 16-pin style OBD connector typically found in passenger cars. It is 24VDC and is to be used with the DAVIE Service Tool. Communication with the engine must be done through the 9-pin Diagnostic connector(12VDC) located in the lower dash between the steering wheel and door aperture.

7-7

Section 7 Electrical

Dash Controls

1 Light switch 2 Instrument panel 3 Speedometer 4 Fuel level and DEF level gauges 5 Warning indicators 6 Master display 7 Warning indicators 8 Air pressure gauge 9 Tachometer 10 Speedometer display 11 Clock, outside temperature and trip odometer display 12 Warning indicators 13 Gear display 14 N/A 15 Instrument lighting(ON/OFF) 16 N/A 17 N/A

1 2 3 4 5

6 7

1 Instrument lighting dimmer 2 PTO switch (Optional) 3 Hazard lights 4 Air suspension dump switch position (if optioned) 5 Differential lock switch position (if optioned) 6 Diesel particulate filter Regen (DPF) 7 Radio and storage

Figure 7-5.1 Dash Contols-1

Figure 7-5.2 Dash Contols-2

7-8

Section 7 Electrical

Power Distribution Center.

Figure 7.6.1 Pwer Distribution Center Reference Figure 7.6.2

Pin

Orange Description

Pin

Grey Description

4C PDC Ground 1A DIP HL (12V+) 4D PDC Ground 1B DIP HL (24V+) 4F ECM Power (12V+) 1C LH Turn (12V+) 4G ECM Power (12V+) 1D LH Turn (24V+) 4B XMSN ECU (12V+) 1E RH Turn (24V+)

1F RH Turn (12V+) 1G Main HL (24V+) 1H Main HL (12V+)

3A

Black Heat Fuel Filter (12V+)

12A

Brown Fog Lamp (12V+)

3F PDC Ground 12B Fog Lamp Sw (24V+) 3G PDC Ground 12C Chassis Ignition (12V+) 3H Converter Ignition 12D Ignition Signal (24V+) 3C 9-pin Diagnostic(12V+) 3B XMSN Actuator

12E NOX up (12V+) 12F NOX down (12V+) 12G Body Lamp (24V+) 12H Body Lamp (12V+)

2C

Red Stop Lamp (12V+)

11A

Green DCU Power (12V+)

2D Stop Lamp (24V+) 11B Line heat (12V+) 2E Clearance (24V+) 11C Starter sol (12V+) 2F Clearance (12V+) 11D Start Signal (24V+)

11E Ignition Signal (24V+) 11F Engine Ignition (12V+) 11G ECM w/u (12V+) 11H DCU w/u (12V+)

The voltage converter provides 24V to cab systems. It is located inside the battery box. This voltage converter works with the Power Distribution Center (PDC) with the following characteristics: 12V Input 24V output Input Current: 80 Amps Output Current: 40 Amps Temperature range: -40C to +85C

7-9

Section 7 Electrical

The output voltage from cab to chassis is 24V. The spare circuits in the PDC located in the battery box as described in Table 7-1 are 12V.

Spare Cir- cuit Pow-

ered Through:

Minimum Wire

Gauge

Pin A

Pin B

Circuit PDC

Terminal

Capacity (Fuse number/Amperes).

Install a fuse of appropriate rating.

Numbered connector Location PDC at battery box.

Spare 1 16 RG7 RH7 2B F20/10Amp Red Connector (B068-7099-F) Spare 2 16 RG7 RH7 2G F20/10Amp Red Connector (B068-7099-F)

Table 7-1 Additional Spare Circuits for Wiring

On Power Distribution Center (chassis).

Figure 7-6.2 Power Distribution Center( Chassis)

7-10

Section 7 Electrical

Body Builder 9 pin connector

Figure 7-7 Body Builder 9 Pin Connector

The connector shown above is available for exterior lighting functions in addition to lighting circuits at the end of frame.

Table 7-2 Body Builder 9 Pin Connector

WIRE DESCRIPTION

FUNCTION

PIN

CIRCUIT WIRE

COLOR CAPACITY FUSE

(AMPERES NUMBER)

WIRE GAUGE

GND Ground R WHT2400 White 6 Stop LP Stop lamp S YEL2601 Yellow F18 / 25A 8

Not Connected T Not Connected Not Connected U Not Connected

Tails/Marker LP Tails / markers lamps V YEL2422 Yellow F19 / 20A 12 Turn RH rear Turn signal right hand rear W YEL2007 Yellow F15 / 15A 12 Backup LP Backup lamp X YEL2960 Yellow TCU Relay 12 Turn LH rear Turn signal left hand rear Y YEL2006 Yellow F14 / 15A 12 Markers LP Markers lamps Z YEL2412 Yellow F19 / 20A 12

7-11

Section 7 Electrical

Model 220 PTO Wiring Information Wiring of the Current Model 220 is different from previous version of the Model 220. Please see the information below for basic wiring and functionality. 1) If equipped, the factory PTO dash switch will tell the VIC to go to PTO mode. 2) J124 connector on the transmission needs 12V to tell the Allison TCM to enable PTO mode. 3) J125 connector on the transmission is a ground output signal from the Allison TCM for the PTO. 4) J126 connector on the transmission is a 24V output signal from the VIC when the PTO dash switch is on. 5) J128 connector on the transmission needs a ground to feedback to the VIC for PTO engaged status (must occur within 3-4 seconds after PTO switch). Option 1: Provide a ground from the PTO engaged switch to J128. Option 2: J128 & J125 can be spliced together for the feedback ground to the VIC. Please note: J128 & J125 will not mate together, so connectors will have to be cut off and spliced. 6) Pin 10 of the 12-pin Remote PTO connector (P124) on the engine harness OR- pin B of the 3-pin connector (J144) on the engine harness needs a ground to feedback to the VIC for PTO engaged status. This performs the same function as item 5 above. This is primarily used for remote set-ups outside the cab.

As an example for setting up a PTO if using the factory PTO dash switch and one pre-set RPM: (Refer Figure 7.9) A) Use J126 to drive your PTO solenoid. This is 24V, so you may need to use a relay if the PTO requires 12V or a ground. B) Send 12V to connector J124 for the Allison TCM when the PTO is engaged. This 12V can be borrowed from the relay used in step A) above. C) Provide a ground to J128 for feedback to the VIC when the PTO is engaged. This can be done by either splicing J125 & J128 together or by running a separate wire from the switch directly on the PTO (if equipped) to J128. This ground must be applied within 3-4 seconds after the PTO switch is enabled. D) Set your desired engine RPM for pre-set speed with DAVIE. This is found under Customer Parameters.

Please note: This information relates only to setting up the mechanical PTO for operation. This does not address the additional function of ESC (Engine Speed Control), as this is a separate function. Engine Speed Control must be enabled in the VIC programming and requires a modified PRS file. Instructions for use of ESC follow.

Engine Speed Control (ESC)

ESC can be fixed (pre-programmed) engine speed or variable engine speed. The Euro 6 only has two pre-programmed engine speeds N2 and N3. N VAR is available using the SET+ and SET- to increase and decrease speed.

To activate these speeds the ESC must first be enabled by providing a high signal (12-24V) on pin 12 of the 12-pin connector on the engine harness (P124).

The N2 and N3 can then be activated by providing a high signal on pins 7 and 6 respectively of the 12-pin

connector on the engine harness (P124). N VAR can be activated by providing a high signal on pin 8 of the 12-pin connector on the engine harness (P124).

(N refers to a Speed Set point)

If N VAR variable control is desired with the steering wheel switches:

A high signal (12-24V) is provided to pin 12 of the 12pin connector on the engine harness (P124). A high signal is provided to pin 8 of the 12pin connector (P124). Use the SET+ and SET-steering wheel switches to bump the throttle up and down. The parking brake must be set for proper functionality.

7-12

Section 7 Electrical

Figure 7-8.1 Typical PTO Wiring for Euro 6 LFNA 12V PTO Solenoid

7-13

Section 7 Electrical

Figure 7-8.2 Typical PTO Wiring for Euro 6 LFNA 24V PTO Solenoid

7-14

Section 7 Electrical

Remote PTO / Throttle Harness

This option provides a connection from the engine ECU to the end of the frame to fit the engine throttle remote control and PTOs. Controls are not provided. A 12-pin Deutsch connector (Deutsch P/N DT06-12SA-P012) is included.

Adding Electrical Options

WARNING!

Follow the engine manufacturers guidelines for use of these circuits. See your engine manufacturer to verify that the engine is programmed correctly for the intended applications. Failure to properly program the engine or wire these circuits could cause an accident.

Figure 7-9 A 12-pin Deutsch connector and remote PTO Control

A-1

Appendix A Vehicle Identication

VEHICLE IDENTIFICATION NUMBER A 17character number (numeral and letter combination) forms the Vehicle Identication Number (VIN) which includes the Chassis Number. It contains among other information, the model year (4), assembly plant (5), and vehicle serial number (6). See Figure A1

Serial Number Chassis Number

Figure A-1. Vehicle Identication Number (VIN).

The model year (4) is designated by an alphanumeric code in the tenth character position in the VIN. See Table A-1 and Figure A1.

Code Year C 2012 D 2013 E 2014 F 2015 G 2016 H 2017

Table A-1. Model Year (Code) Designations. VIN Location

The VIN is marked on the Incomplete Vehicle Certication Label (on trucks). It is located either on the drivers door edge or door frame. See Figure A2.

Chassis Number Locations

The Chassis Number comprises the last six characters of the VIN.

The Model 220 chassis number is shown in multiple locations. Right frame rail, bottom ange (underside), about 4 to 4.5 ft. from the front end: stamped. Left frame rail, top of ange, about 4 to 4.5 feet from front end: stamped Tire, Rim, and Weight Rating Data label. Major Components and Weights label. Paint Identication label.

M

A-2

CERTIFICATION LABELS Components and Weights Label

Appendix A Vehicle Identication

The Major Components and Weights Label is located on either the drivers side door edge or on the door frame. See Fig- ure A2. It includes: chassis weight and gross weight; plus, model and serial numbers for the vehicle, engine, transmis- sion, and axles.

Tire, Rim and Weight Rating Data label

Safety Mark (Canadian Registry Only)

Final Stage Manufacturer Label to be Installed by Final Stage Manufacturer

Chassis Serial Number

Major Components and Weights Label

Incomplete Vehicle Certication Label

Figure A-2. Locations of Certication Labels - Drivers Door

Figure A-2. Drivers Door and Door Frame Label

Tire/Rim and Weight Rating Data Label

The Tire/Rim and Weight Rating Data Label is located on the drivers side door edge, above the door latch. See Figure A2. It contains the following information:

Note:

GVWR Gross Vehicle Weight Rating GAWR FRONT and REAR Gross Axle Weight Ratings for Front and Rear Axle TIRE/RIM SIZES AND INFLATION PRESSURES Tire/Rim Sizes and Cold Pressure Minimums Chassis (Serial) Number

GVWR is the TOTAL WEIGHT the vehicle is designed to carry. This includes the weight of the empty vehicle, loading platform, occupants, fuel, and any load. Axle weight ratings are listed on the edge of the drivers door.

Incomplete Vehicle Certication Label The Incomplete Vehicle Certication Label is located on the drivers side door edge below the latch. See Figure A 2. It contains the following information:

DATE OF MANUFACTURE VIN Vehicle Identication Number LISTING OF APPLICABLE FEDERAL MOTOR VEHICLE SAFETY STANDARDS

A-3

Appendix A Vehicle Identication

COMPONENT IDENTIFICATION

Each of the following components has their own identication label.

Engine Identication

The engine dataplate provides important facts about the engine. The engine serial number (ESN) and control parts list (CPL) provide information for service and ordering parts. The engine dataplate must not be changed unless approved by PACCAR Inc.

The dataplate is located on rocker lever cover as illustrated.

Have the following engine data available when communicating with a PACCAR Authorized Repair Location:

1. Engine Serial Number (ESN) 2. Engine model information 3. Control Parts List (CPL) 4. Valve Lash 5. Horsepower and rpm rating

1. Dataplate 2. ESN

Figure A-3 Engine Identication Location

If the engine dataplate (1) is not readable, the ESN (2) can be found on the engine block on top of the lubricat- ing oil cooler housing. Additional engine information is on the electronic control module (ECM) dataplate.

A-4

Appendix A Vehicle Identication

Transmission Identication

The transmission identication number is stamped on a tag afxed to the right forward side of the transmission case. It includes, among other specications, the transmission model, serial and part number.

Front Axle Identication

The front axle has an identication tag located on the front axle beam. It includes the axle model, part number and serial number.

Figure A-4 Front Axle Identication Rear Axle Identication The rear axle identication numbering system includes two labels or stamps.

1. Axle Housing Number Tag, located on the left forward side of the housing arm. This tag identies the ax-

le housing.

2. Axle Differential Carrier Identication, located on the top side of the differential carrier. The following in- formation is either stamped, or marked with a metal tag: Model No., Carrier Production Assembly No., Carrier Assembly Serial No., Gear Ratio, Axle Specications Number and OEM part number and country of origin.

2

1

Figure A-5 Rear Axle Identication 1

Note: Illustrated identication tag locations are typical. Actual locations may vary by axle manufacturer and with

single versus tandem axles.

B-1

Appendix B Weight Distribution

INTRODUCTION In the Medium Duty truck market, matching the wheelbase to the body specication is extremely important. Se- lection of the wrong wheelbase may lead to premature component failure, poor performance, and ultimately a dissatised customer. Before selecting the proper wheelbase, it is important to have a basic understanding of weight distribution.

Abbreviations Throughout this section, abbreviations are used to describe certain features and requirements of the vehicle (see the list below). Review this list frequently so you know what the abbreviations mean.

AF = Frame rail overhang length behind the rear axle BL = Body Length CA = Back of cab to centerline of rear axle

Note: The Model 220 CA gures are measured from the true back of cab to the centerline of the rear axle. To obtain a usable CA the body builder must subtract any required space behind the cab, which may be needed for other equipment.

CG = Center of gravity: the balance point or center of a load. It is usually identied by a circle

with alternating black and white quarters. CGf = Distance from the centerline of the front axle to the center of gravity of the load (L). The

load can be any load such as a fuel tank, a body, or the payload. FA = Front Axle GVWR = Gross Vehicle Weight Rating L = Load: the weight that is carried. This could be the body, the payload or any item that has its

weight distributed between the two axles. Lf = Portion of load (L) carried by front axle Lr = Portion of load (L) carried by rear axle RA = Rear Axle WB = Wheelbase Length

B-2

100 lbs

100 In. 214 In.

Appendix B Weight Distribution

CALCULATIONS Weight Distribution without Body There are two primary equations used in weight distribution calculations:

The rst equation determines the portion of the load carried by the rear axle (Lr). CGf

Lr = WB X L Portion of Load Carried by the Rear Axle Equation 1

The second determines the portion of the load carried by the front axle (Lf).

Lf = L - Lr Portion of Load Carried by the Front Axle Equation 2

Note: For the purposes of calculation, the load (L) in these equations can be either actual revenue producing load or it can be other weight that is carried such as the van body or an optional fuel tank.

Front Axle

Figure B-1. Balanced Load: CGf 100 in. from front axle

Step 1. Figures B1 and B2 show a representation of a 214 inch (5435.6 mm) wheelbase (WB) truck de- signed to carry a 100lb. (45.3kg) load. Figure B1 represents a truck with the load placed an equal distance between the two axles.

a. For our balanced load example we need to establish the center of gravity location (CGf, as

shown in Figure B1) by dividing the wheelbase by 2: 214

CGf = 2 = 107 in (2717.8 mm)

b. Use equations 1 and 2 to determine the portions of the load carried by each axle.

The weight distribution is calculated as illustrated below:

Lr = CGf

WB X L 107

214 (100) = 50 lbs (23 kg)

Lf = L - Lr 100 - 50 = 50 lbs (23 kg)

Since the load is centered between both axles, 50 percent of the load is carried by each axle: i.e., 50 lb. (22.6 kg) is distributed to each axle.

B-3

100 lbs

133 In. 214 In.

Appendix B Weight Distribution

C. In Figure B2, the load (L) is located 133 in. (3378 mm) from the front axle. Moving the load

towards the rear axle changes the weight distribution. Use equations 1 and 2 to determine the portion of the load carried by each axle.

Front Axle

Figure B-2. Unbalanced Load: CGf 133 In. From Front Axle

CGf = 133 in. (3378 mm)

Lr =

CGf WB X L

133 214 (100) = 62.14 lbs (28.18 kg)

Lf = L - Lr 100 62.14 = 38.86 lbs (17.6 kg)

The rear axle now carries a greater proportion of the load than the front axle.

Although it is usually not important to know the CG of the chassis; it is important to know the CG location of truck bodies, accessories, or loads that may be placed on the chassis. This example shows that the location of the CG of an object relative to the front and rear axles (FA and RA) affects the load carried by each axle.

For most relatively uniform objects such as van bodies and fuel tanks, the CG is located close to the midpoint of the object. For nonuniform objects such as liftgates and refrigeration units, obtain the CG from the equipment manufacturer.

B-4

Appendix B Weight Distribution

Weight Distribution with Body

Chassis Weights Step 2. In the following example, a truck is modied to include a van body mounted to the chassis. This example is a chassis, 214 inches (5435.6 mm) in WB, with a standard drivetrain and fuel tank. It is a 26,000 lb. GVWR with a 8,948 lb. front axle and a 17,052 lb. rear axle.

When calculating weight distributions, start by determining chassis ground weights for each axle. The actual chassis weight will vary with the wheelbase and the options installed. Listed in Tables B-1 and B-2 are the chassis tare weights for the standard single rear axle vehicles and each wheelbase conguration.

We see that the 214-inch wheelbase, 2-axle has the following tare weights:

FA = 6263.4 RA = 9628.7

Model 220 with nominal weights and CGs. See your Peterbilt Dealer for more exact weights and CGs. It also lists their added weight when installed on the chassis and the location (from the front axle) of the CG of this added weight.

Wheelbase Inches

Front lb (kg)

Rear lb (kg)

Total lb (kg)

214 6263.4 (2,841) 9628.7 (4367.5) 15892.1 (7,208.5)

Table B-1 Model 220 Single Rear Axle Bare Chassis Tare Weights (no driver, no fuel)

Note: The weight in Table B-1 represents an example of a standard chassis

B-5

Appendix B Weight Distribution

Now we will calculate the distributed weight of van body that weighs 4825 pounds (2188.5 kg). Since an empty van is very close to a uniform object, you can assume that the CG of the van body is at a point equal to half of the BL.

Figure B-3. Balanced Body Unloaded: CGf 184.7 in. (4691.45 mm) from front axle.

When the body is mounted on the chassis, assume that the forward edge is positioned 4 inches (102 mm) be- hind the back of the cab. This is equivalent to 17. 3 i n c h e s ( 4 39 . 4 mm) behind the front axle. Therefore, the CG of the body is located 72 inches plus half the body length from the front axle.

Use Equations 1 and 2 to calculate the distributed additional weight of the body:

Lr = CGf

WB X L 184.7

214 (4825) = 4164.4 lbs (1888.9 kg)

Lf = L - Lr 4825 4164.4 = 660.5 lbs (299.6 kg)

Adding a liftgate to the van body will present some interesting weight distribution results. We will add a 1455 pound (659.9 kg) liftgate to the end of the van body. The CG location of non-uniform objects, such as a liftgate, must be provided by the equipment manufacturer. For our example, the liftgate manufacturer has provided i n - stallation information that indicates the liftgate CGf is located 322.2 in (8183.9 mm) behind the front axle.

Rear Liftgate Example

Figure B-4. Liftgate Example: CGf 322.2 in (8183.9 mm) from front axle.

B-6

Appendix B Weight Distribution

Use CGf = 246 in equations 1 and 2 to determine how the liftgate weight is distributed to the axles.

Lr =

CGf

WB X L

322.2

214 X 1455 = 2190.6 lbs (993.6 kg)

Lf = L - Lr 1455 - 2190.6 = -735.6 lbs (-333.6 kg)

This negative weight on the front axle illustrates the difference between the distribution of weight (L) mounted behind the rear axle versus in front of the rear axle.

The load carried by the rear axle is greater than the weight of the liftgate itself. Since the weight of

the liftgate (added to the vehicle) cannot be greater than 1,455 lb, the front axle loading is reduced by a compensating amount (735.6 lb). The combined weight on the front and rear axles is equal to that of the liftgate.

Weight added behind the rear axle has the effect of unloading the front axle. The amount of this

front axle load reduction is equal to the extra weight added to the rear axle.

By positioning equipment behind the rear axle, the effective load on the rear axle is more than the weight of the equipment.

The farther behind the rear axle the load is mounted, the greater the load on the rear axle. However,

the combined weight, distributed to the front and rear axles (Lf plus Lr), does not exceed the weight of the liftgate.

In order to get a realistic curb weight, we add weight for a driver and fuel. For purposes of calculation, we use a standard of 200 lbs. (91 kg) for the driver. Of course, your driver weight will vary. Using CGf = 10 in equations 1 and 2:

Lr = CGf

WB X L 10

214 (200) = 9.34 lbs (4.2 kg)

Lf = L - Lr 200 - 9.34 = 190.6 lbs (86.4 kg)

We calculate the fuel load using 7 lbs per gallon as the weight for diesel fuel.

45 gal x (7 lbs/gal) = 315 lbs (142.8 kg)

Using CGf=73.9 and equations 1 and 2 for the standard tank:

Lr = CGf

WB X L 73.9

214 (315) = 108.7 lbs (49.3 kg)

Lf = L - Lr 315 108.7 = 206.2 lbs (93.53 kg)

Appendix B W

B-7

Appendix B Weight Distribution

Model 220 sample, Assume that the payload is evenly distributed. Freight that is distributed evenly is referred to as a water level load. Our payload total is 14,500 lb. Since it is an evenly distributed water level load, its CG loca- tion will be the same as the CG location of the van body. See Figure B5.

CGf = 1 2

BL + 72 1 (168) + 72 = 156 in. 2

Using CGf = 156 in equations 1 and 2:

Lr = CGf

WB X L 156

214 (14,500) = 10,570 lbs (4794.5 kg)

Lf = L - Lr 14,500 10,570 = 3,929.9 lbs (1782.5 kg)

Figure B-5. Balanced Body Loaded: CGf 184.7 in (4691.45 mm) from front axle.

Item Front Axle (FA) lb (kg)

Rear Axle (RA) lb (kg)

Total lb (kg)

Chassis 6845.3 3104.98 3439.2 1559.995 10284.5 4664.971 Fuel 45 Gal Std, Tank 206.2 93.5307 108.7 49.30549 314.9 142.8362 Tare Weight 7051.5 3198.51 3547.9 1609.3 10599.4 4807.807 Liftgate -735.6 -333.66 2490.6 1129.717 1755 796.0546 Van Body 660.7 299.688 4164.3 1888.895 4825 2188.583 Driver 190.65 86.4774 9.34 4.236553 199.99 90.71394 Curb Weight 7167.25 3251.01 10212.14 4632.149 17379.39 7883.159 Payload 3929.9 1782.57 10570 4794.471 14499.9 6577.044 Total Ground Weight 11097.15 5033.58 20782.14 9426.62 31879.29 14460.2 Chassis Axle Ratings 12000 5443.11 21000 9525.44 33000 14968.55

Table B-2 Model 220 Weight Distribution and Chassis Rating Calculation (sample)

B-8

Appendix B Weight Distribution

Weight Distribution Analysis

Step 3. The nal step is to total all of the front and rear axle weights to ensure that the axles are not overload- ed. Table B-4 shows the assembled information in an easy to read format.

Compare the calculated axle ground totals against the axle weight ratings to be sure that the truck is

properly specied to haul this load.

From this, it is evident that the chassis is properly equipped for this job.

These calculations illustrate the importance of doing the weight distribution analysis. In some cases the addi- tion of one component (for example, a liftgate) can produce a dramatic difference.

Body Length Step 4. Your analysis may produce results that indicate an overloaded axle with a total loaded chassis weight less than the GVW. This shows that you need to use a different body length for the truck. Each wheelbase can accommodate several different body lengths. However, for each wheelbase and GVW one particular body length will provide close to optimum weight distribution on both axles.

a. Table B-3 lists Recommended Body Lengths for a particular wheelbase and GVW. These body lengths provide the best weight distribution for the listed wheelbase.

Note: These charts were generated assuming a plain van body with water level loading. Any common additions such as lift gates or refrigeration units may indicate a different wheelbase for a given body length. Also, different body styles may require a different WB for a given size.

B-9

Appendix B Weight Distribution

Table B-3 Available Model 220 Body Lengths

Remember that water level loading assumes that the load is arranged evenly in the body (as water would be in a tank). If uneven load distribution is part of the vehicle layout, your weight distribution analysis may indicate that a different body length, deviating from the recommended length, will provide the best weight distribution.

Note: You should always perform a weight distribution analysis to help ensure the vehicle performs properly and meets your customers expectations.

Wheelbase In. (mm) Body Length (Ft) 26,000 GVW 33,000 GVW

142 (3606.8) 16 146 (3708.4) 16 154 (3911.6) 17 158 (4013.2) 17 166 (4216.4) 18 170 (4318) 18 178 (4521) 20 182 (4622.8) 20 190 (4826) 22 194 (4927.6) 22 202 (5130.8) 24 206 (5232.4) 24 214 (5435.6) 26 218 (5537.2) 26 226 (5740.4) 27 230 (5842) 27 238 (6045.2) 28 242 (6146.8) 28 *For trucks built before and including 6/22/2012

Index

A Frame, welding 6-2 Abbreviations vi Front axle serial number A-4 Front View 3-7 B Fuel tank locations 3-17 Body mount, rear 5-9 Body mounting 5-1 G Body mounting with U-bolts 5-7 Ground clearance 3-8 Brackets, body mounting 5-5 I C Incomplete vehicle certication 2-2 Calculations B-2 Incomplete Vehicle Certication Label A-2 Cautions 2-1 Certication label a-2 M Chassis maintenance 1-1 Mounting holes, frame 5-6 Chassis Number A-1 Chassis weight B-4 N Cab/Chassis Interface 7-3 Noise Requirements 2-3 Clearance, air lines and wiring 5-8 Notes 2-1 Critical clearances 5-4 Crossmember location 3-14 O Crossmembers 6-2 Operating information 1-1 Options weights B-4 D Dimensions 3-1 R Dimensions, air tanks 3-12 Rear axle identication A-4 Dimensions, battery box 3-12 Rear suspension, changing 6-1 Dimensions, crew cab, conversion 3-11 Rear View 3-7 Dimensions, overall 3-4 Remote PTO/throttle harness 7-14 Repair information 1-1 E Electrical circuits 7-1 S Emissions requirements 2-3 Safety signals 2-1 Engine serial number A-3 Scope 1-1 Sill spacer 5-5 F Spare Circuits 7-1 Federal Motor Vehicle Safety Standards 2-2 Step height 3-10 Final stage manufacturer 2-2 Fishplate bracket 5-9 T Frame, drilling 5-7 Transmission identication

Turning radius A-4 3-2

V Vehicle Identication Number A-1 W Warnings 2-1 Water level load B-9 Weight distribution B-1 Weight distributi

Manualsnet FAQs

If you want to find out how the Body Builder Peterbilt works, you can view and download the Peterbilt Model 220 Truck Body Builder Operator’s Manual on the Manualsnet website.

Yes, we have the Operator's Manual for Peterbilt Body Builder as well as other Peterbilt manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operator's Manual should include all the details that are needed to use a Peterbilt Body Builder. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Peterbilt Model 220 Truck Body Builder Operator’s Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Peterbilt Model 220 Truck Body Builder Operator’s Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Peterbilt Model 220 Truck Body Builder Operator’s Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Peterbilt Model 220 Truck Body Builder Operator’s Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Peterbilt Model 220 Truck Body Builder Operator’s Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.