Contents

Pelco PelcoNet NET350 C2907M-D Transmitter Operations Manual PDF

1 of 92
1 of 92

Summary of Content for Pelco PelcoNet NET350 C2907M-D Transmitter Operations Manual PDF

PelcoNet

NET350 Multimedia Transmission Via Network

I N S T A L L A T I O N / O P E R A T I O N

C2907M-D (4/05)

Contents Important Safeguards and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Radio and Television Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

What Is the PelcoNet NET350 Transmission System? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 How Do LANs and WANs Work? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Who Should Install the PelcoNet NET350 Transmission System? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Instructions for the Network Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 The Transmitter and Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 The Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Minimum PC Requirements (As Needed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Optional Compatible Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Front Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Rear Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Typical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Mounting the NET350 to the Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Connecting Video Sources or Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Connecting Data Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Connecting Audio Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Connecting an Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Connecting a Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Connecting to a LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Switching on Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Box-to-box Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Configuration Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Configuration Using a Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Setup Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Configuration Page for General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Configuration Page for MPEG-4 Video Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Configuration Page for Video Decoder Settings (Receiver Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Configuration Page for Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Configuration Page for Alarm Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Configuration Page for Relay Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Configuration Page for COM 1 Interface Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Configuration Page for COM 2 Interface Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Configuration Page for Local COM Interface Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Configuration Page for Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Configuration Pages for Media Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Configuration Using a Terminal Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Typical Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Terminal Program Transmitter Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Terminal Program Receiver Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Command Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Live Video and Server Push Video Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Displaying Video On a Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

2 C2907M-D (4/05)

Using the Audio Transmission Feature of a Live Video Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Web Browser Control Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Matrix Live Video/Server Push Page Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Genex Live Video/Server Push Page Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Spectra Live Video/Server Push Page Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Esprit Live Video/Server Push Page Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Keyboard Live Video/Server Push Page Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Recording and Viewing the Display on a PC and the NET350 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Choosing Where to Store the File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Recording a Snapshot from Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Viewing a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Recording the Video Display onto the PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Recording the Video Display Through Compactflash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Viewing the Video Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Media Playback Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Viewing a File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Backing up a File Onto a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Recording a Snapshot from a File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Software Upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Resetting the NET350 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Terminal Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Troubleshooting a TCP/IP Network Using a Ping Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Troubleshooting Connection Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Troubleshooting the Video Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Appendix A Connecting PelcoNet to Various Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Connecting PelcoNet to Various Components with Assorted Keyboards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Connection Scenario 1 Using a KBD300A In Direct Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Connection Scenario 2 Using a KBD4000 for Multiplexer Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Connection Scenario 3 Using a CM9760-KBD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Connecting a Local Keyboard to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Connecting PelcoNet COM 1 RS-232 Port to the Genex Multiplexer COM Out Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Connecting PelcoNet to a CM6700 and KBD200A for Remote ASCII Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Connecting PelcoNet to a CM6700 ASCII Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Connecting PelcoNet to a CM9760-DT for Remote Browser Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Connecting PelcoNet to CM9700 for Remote Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Connecting a PelcoNet Transmitter to the CM6800 ASCII Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Connecting PelcoNet to a CM6800 and KBD200A for Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Appendix B Frequently Asked Questions (FAQs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

C2907M-D (4/05) 3

List of Illustrations 1 Front Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 2 Rear Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 3 Conguration for Box-To-Box Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 4 LAN Box-To-Box Connection (Transmitter, Receiver, Fixed Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 5 LAN Box-To-Box Connection (Transmitter, Receiver, Spectra) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 6 LAN Box-To-Box Connection (Transmitter, Receiver, Spectra, Genex) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 7 LAN Browser-To-Box Connection (Transmitter, Browser, Fixed Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 8 LAN Browser-To-Box Connection (Transmitter, Browser, Spectra) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 9 LAN Browser-To-Box Connection (Transmitter, Browser, Spectra, Genex) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

10 WAN Box-To-Box Connection (Transmitter, Receiver, Fixed Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 11 WAN Box-To-Box Connection (Transmitter, Receiver, Spectra) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 12 WAN Box-To-Box Connection (Transmitter, Receiver, Spectra, Genex) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 13 WAN Browser-To-Box Connection (Transmitter, Browser, Fixed Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 14 WAN Browser-To-Box Connection (Transmitter, Browser, Spectra) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 15 WAN Browser-To-Box Connection (Transmitter, Browser, Spectra, Genex) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 16 Connection with Pelco Keyboard Control Through a PC (Example Shown with Spectra and Genex) . . . . . . . . . . . . . . . . . .22 17 Securing NET350 to Wall Mount Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 18 Connecting Audio Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 19 Alarm and Relay Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 20 Connecting to the LAN Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 21 PelcoNet Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 22 PelcoNet NET350 Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 23 PelcoNet NET350 Setup Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 24 Conguration Page for General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 25 Conguration Page for MPEG-4 Video Settings (Only One Example Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 26 Conguration Page for Video Decoder Settings (Receiver Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 27 Conguration Page for Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 28 Conguration Page for Alarm Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 29 Motion Detection Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 30 Motion Detection Grid Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 31 Conguration Page for Relay Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 32 Conguration Page for COM 1 Interface Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 33 Conguration Page for COM 2 Interface Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 34 Conguration Page for Local Com Interface Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 35 Conguration Page for Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 36 Partition Settings Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 37 Conguration Page for Time Recording Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 38 Conguration Page for Alarm Recording Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 39 Conguration Page for Properties Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 40 Live Video and Server Push Video Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 41 PelcoNet NET350 Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 42 Device Controls Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 43 Matrix Control Page (Live Video Page Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 44 Genex Control Page (Live Video Page Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 45 Spectra Control Page (Live Video Page Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 46 Esprit Control Page (Live Video Page Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 47 Keyboard Control Page (Live Video Page Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 48 Viewer Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 49 Media Playback Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 50 DB9 Cable Wire Splicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 51 KBD300A (Direct Mode) Connected to a Receiver or Spectra Dome System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 52 KBD4000 Connected to a Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 53 CM9760-KBD Connected to a CM9700-CC1 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 54 Connecting a Local Keyboard to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 55 Connecting PelcoNet to Genex Using the COM 1 RS-232 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 56 Using PelcoNet with CM6700 and KBD200A to Provide Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 57 Using PelcoNet with CM6700 to Provide Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 58 Using PelcoNet with CM9760-DT to Provide Remote Control of a 9760 Monitor Output . . . . . . . . . . . . . . . . . . . . . . . . . . .81 59 Using PelcoNet to Transmit Data and Video Between 9700 Nodes (9760 Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

4 C2907M-D (4/05)

60 Using PelcoNet to Receive Data and Video Between 9700 Nodes (9760 Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 61 Manager Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 62 Menu Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 63 Using PelcoNet with CM6800 and KBD200A to Provide Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

C2907M-D (4/05) 5

6 C2907M-D (4/05)

List of Tables

A Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 B Terminal Command Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 C Live Video Page Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 D LED Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Important Safeguards and Warnings Observe the following warnings before installing and using this product.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.

9. Only use attachments/accessories specied by the manufacturer.

10. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, the apparatus does not operate normally, or the apparatus has been dropped.

11. Apparatus shall not be exposed to dripping or splashing, and no objects lled with liquids, such as vases, shall be placed on the apparatus.

12. Warning: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.

13. To reduce the risk of shock, do not perform any servicing other than that contained in the operating instructions unless you are qualied to do so.

14. Unless the unit meets NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P standards, it is designed for indoor use only and must not be installed where exposed to rain and moisture.

15. Only use parts recommended by Pelco.

16. Use only installation methods and materials capable of supporting four times the maximum specied load.

REGULATORY NOTICES This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

You may also nd helpful the following booklet, prepared by the FCC: How to Identify and Resolve Radio-TV

Interference Problems. This booklet is available from the U.S. Government Printing Ofce, Washington D.C. 20402.

Changes and modications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commissions rules.

C2907M-D (4/05) 7

What Is the PelcoNet NET350 Transmission System? The PelcoNet NET350 transmission system is technology that lets you view video in real time across a LAN (local area network) and even WANs (wide area networks). This technology is based on the TCP/IP protocol suite and Ethernet technology, providing compatibility with todays networking standards.

The following devices can be controlled from your computer through Internet Explorer with the PelcoNet NET350 transmission system: Spectra, Esprit, Genex multiplexer, CM9700 systems (older CM9760s require CM9760 data translator), CM6700 (through integrated ASCII port, COM 2), and the CM6800 matrix.

(Refer to Glossary section for denitions of terms used in this manual.)

HOW DO LANS AND WANS WORK? A LAN consists of multiple computers connected together, sharing information. This information could be les, e-mail, printers, orwith the

PelcoNet NET350 transmission systemeven live video and audio.

A WAN consists of multiple LANs connected through routers and gateways (for example, the Internet).

In any network environment, each device needs a unique address so other computers on the network know how to reach it.

It is similar to a city with street addresses. For the post ofce to deliver mail to your house, you need a unique street address for the mail carrier to nd you. A network is like a city. Like a street address, the IP address on your computer is your address on the network. The IP address is how other computers can nd you on the network.

Remember that the IP address must be unique on the network.

When there are multiple networks and you are using the TCP/IP protocol, there must be a way to communicate between the two networks. A physical device called a router is required. The routers IP address is referred to as the default gateway IP address.

A cable that connects one computer to another is like a city street you can use to get from one house to another. The cable lets you communicate with each other on the network. This cable is Category 5 cable with RJ-45 connectors at each end. (It looks like a phone cord, only slightly larger.)

WHO SHOULD INSTALL THE PELCONET NET350 TRANSMISSION SYSTEM? NOTE: Unless you are very familiar with how computers work, consult your network administrator for help.

Installation is a matter of conguring an IP address using a standard terminal program or Internet Explorer and connecting the PelcoNet NET350 transmission system to the Ethernet network. You should have the following background and experience to congure and install these units:

Working knowledge of basic network management concepts and terminology

Working knowledge of tools and procedures for installing and operating sensitive electronic equipment

8 C2907M-D (4/05)

Instructions for the Network Administrator The PelcoNet NET350 transmission system allows live video transmission to be viewed over TCP/IP-based networks. This section is intended to help the network administrator know what is involved with installing this product and how it will affect the network. The person installing the product will need the following information about the network to make the network function properly.

THE TRANSMITTER AND RECEIVER A valid IP address* for each PelcoNet NET350 transmission system unit

Subnet mask*

Default gateway (if applicable)

E-mail servers IP address (if applicable)

Dedicated maximum allowable amount of bandwidth for live video**

* = Required for the PelcoNet NET350 transmission system to function properly

** = The PelcoNet NET350 transmission system requires a continuous amount of bandwidth to display true live video. Pelco recommends using switching hubs with the product so the amount of bandwidth available to each unit is constant and reliable.

THE BROWSER If you plan to use a browser to view live video across the network, there are procedures to complete before you can use the browser, such as installing the ActiveX platform. If you installed Internet Explorer 6.0 from the CD that came with the PelcoNet NET350 transmission system, you can skip step 1 below. Otherwise, perform the following before trying to use the browser.

1. Internet Explorer 6.0 or higher must be installed before continuing.

2. Set the computers display settings to use 16- or 32-bit color.

3. Insert the supplied resource CD. It will open automatically. If it fails to open automatically, perform steps a through d below.

a. Click the Start menu in the Windows operating system.

b. Click Run.

c. In the Open box, type D:\START.EXE (where D:\ = your CD ROM drive letter).

d. Click OK.

4. Click Software and then click Install PelcoNet ActiveX.

5. Follow the on-screen setup instructions to nish installing the plug-in.

MINIMUM PC REQUIREMENTS (AS NEEDED) PC (Pentium 4 microprocessor, 1.6 GHz) with Windows 98/2000/XP operating system

Network card

Microsoft Internet Explorer 6.0 (or higher) or PelcoNet NET350R (receiver) and video monitor

Free serial interface and terminal program

Screen resolution of 1024 x 768 or higher, 16- or 32-bit pixel color resolution

RAM of 256 MB

Graphic card (ATI RADEON 7500 or 8500, Matrox G 550 or Parhelia, or NVIDIA GeForce 3 or 4 with direct show-compatible MPEG-4 playback capability)

Ethernet card (100 Mbit recommended)

Sound card (required for audio application)

DirectX 8.1 or 9.0 application programming interface software

C2907M-D (4/05) 9

Overview NOTE: This manual refers to the PelcoNet NET350 transmission system unit when discussing features, functions, or specications that apply to both transmitter and receiver models. Receiver, as used in this manual, refers to a PelcoNet NET350 transmission system receiver unless otherwise noted.

DESCRIPTION The PelcoNet NET350 transmission system is a network video server that encodes and decodes live video, audio, and control data transmitted and received over Ethernet computer networks (either intranet or Internet) using the TCP/IP protocol.

The transmission system consists of two units: a transmitter (NET350T) and a receiver (NET350R)however, only the transmitter is required to use the system. If a receiver is used, video can be displayed on an NTSC or PAL monitor connected to the receiver. If a receiver is not used, video can be displayed on a PC connected to the network through a web browser.

The NET350T includes a CompactFlash interface for video storage.

Dual MPEG-4 video streams, each of which can be set up differently, is a special feature of the NET350. For example, one video stream might be set to record at high resolution while the second might have monitoring at a lower resolution.

Transmitters and receivers are identied by IP addresses, just like any other equipment connected to a computer network.

There is a bidirectional serial interface for remote control of peripherals, such as PTZ cameras. The NET350T can transmit and receive audio and the NET350R can receive audio.

In appropriately congured networks, the multicast function permits simultaneous video transmission in real time to several receivers. For this to work, the UDP and IGMP multicasting protocols must be implemented in the network.

SOFTWARE VERSION This manual documents PelcoNet NET350 software version 3.0.

PACKAGE CONTENTS The following are supplied:

Transmitter (NET350T) or receiver (NET350R)

Universal plug-in power pack with adapters for EU, UK, US, and AU

DB9 cable with pigtail

Wall mount bracket

Quick installation guide

Software resource CD

OPTIONAL COMPATIBLE PRODUCTS

NET350RK The NET350RK rack mount kit provides rack mounting for the PelcoNet NET350. This kit supports the mounting of one, two, or three units per rack. Units can be mounted with either front or real panel forward.

10 C2907M-D (4/05)

FRONT PANEL COMPONENTS The PelcoNet NET350 transmission system uses a compact design. For that reason connectors are placed on both the front and rear panels.

Key:

1 = CompactFlash interface (transmitter only) is a slot for CompactFlash cards and miniature disk drives 2 = Alarm I/O terminals for alarm input and relay output (refer to Figure 19) 3 = RJ-45 Ethernet connector for connecting to the network (10/100) 4 = Power socket 5 = LED I lights red with an active alarm 6 = LED O lights green when the relay is switched 7 = LED L lights green when the unit is connected to the network 8 = LED T ashes yellow when data is transmitted 9 = Hard reset button

Figure 1. Front Panel Components

(Refer to the LEDs section for more information on the LEDs.)

REAR PANEL COMPONENTS

Key:

1 = Video In BNC socket (transmitter) or Video Out BNC socket (receiver) for video source or for an analog video monitor 2 = 75 slide switch (transmitter) for terminating the video input 3 = Audio I/O bidirectional audio interface; 3.5 mm stereo jack for connecting a loudspeaker or an audio source (monaural line), line level 4 = COM2: RS232 serial interface port; 9-pin male sub-D socket for conguration using terminal software 5 = COM1: RS232/422/485 serial interface port; 9-pin male sub-D socket for controlling data transmissions (RS-232, RS-422, and RS-485

protocols) and for conguration using terminal software 6 = Power LED for device status and software upload failure (refer to the LEDs section)

Figure 2. Rear Panel Components

Refer to the LEDs section for more information on the LEDs and to the Hardware Installation section for information on interfacing peripherals to the unit.

Alarm I/O Ethernet Power

OI

CompactFlash

COM2: RS232

COM1: RS232/422/485

Video In

75 Audio I/O

Power

C2907M-D (4/05) 11

Typical Applications There are two ways to make a high performance multimedia transmission system for computer networks:

One way is to use just the transmitter and connect it through the computer network to a PC with a web browser at the receiving end.

Another way is to connect the transmitter through the computer network to a receiver. This is often called a box-to-box connection because it uses two PelcoNet NET350 transmission system units.

In either case, routing dedicated cables from a camera to a monitor is not required because you can use the existing computer network for that purpose.

Refer to gures 3 through 16 for examples of these congurations. Refer to Appendix A for detailed connection illustrations. -

Figure 3. Conguration for Box-To-Box Connections

Video Out

75 Audio I/O

Power

Video In

75 Audio I/O

Power

TCP/IP INTRANET/INTERNET

LAN/WAN

TRANSMITTER

RECEIVER

COM2: RS232

COM1: RS232/422/485

COM2: RS232

COM1: RS232/422/485

12 C2907M-D (4/05)

Figure 4. LAN Box-To-Box Connection (Transmitter, Receiver, Fixed Camera)

Video Out

75 Audio I/O

Power

Video In

75 Audio I/O

Power

TRANSMITTER

RECEIVER

HUB

CAMERA AUDIO

(PREAMP) LINE LEVEL

DATA

DATA

MONITOR AUDIO

COM2: RS232

COM1: RS232/422/485

COM2: RS232

COM1: RS232/422/485

C2907M-D (4/05) 13

Figure 5. LAN Box-To-Box Connection (Transmitter, Receiver, Spectra)

Video Out

75 Audio I/O

Power

Video In

75 Audio I/O

Power

TRANSMITTER

RECEIVER

HUB

SPECTRA

AUDIO (PREAMP) LINE LEVEL

DATA

DATA

MONITOR AUDIO KEYBOARD

VIDEO

COM2: RS232

COM1: RS232/422/485

COM2: RS232

COM1: RS232/422/485

14 C2907M-D (4/05)

Figure 6. LAN Box-To-Box Connection (Transmitter, Receiver, Spectra, Genex)

Video In

75 Audio I/O

Power

TRANSMITTER

HUB

SPECTRA

DATA

VIDEO

GENEX

Video Out

75 Audio I/O

Power

RECEIVER

DATA

MONITOR KEYBOARD

VIDEO

COM2: RS232

COM1: RS232/422/485

COM2: RS232

COM1: RS232/422/485

C2907M-D (4/05) 15

Figure 7. LAN Browser-To-Box Connection (Transmitter, Browser, Fixed Camera)

Figure 8. LAN Browser-To-Box Connection (Transmitter, Browser, Spectra)

Video In

75 Audio I/O

Power

TRANSMITTER

HUB

BROWSER

CAMERA

COM2: RS232

COM1: RS232/422/485

Video In

75 Audio I/O

COM2: RS232

COM1: RS232/422/485

Power

TRANSMITTER

HUB

SPECTRA

DATA

BROWSER

VIDEO

16 C2907M-D (4/05)

Figure 9. LAN Browser-To-Box Connection (Transmitter, Browser, Spectra, Genex)

Video In

75 Audio I/O

Power

TRANSMITTER

HUB

SPECTRA

DATA

VIDEO

GENEX

Video Out

75 Audio I/O

Power

RECEIVER

DATA

MONITOR KEYBOARD

VIDEO

COM2: RS232

COM1: RS232/422/485

COM2: RS232

COM1: RS232/422/485

C2907M-D (4/05) 17

Figure 10. WAN Box-To-Box Connection (Transmitter, Receiver, Fixed Camera)

Video Out

75 Audio I/O

Power

Video In

75 Audio I/O

Power

TRANSMITTER

RECEIVER

CAMERA AUDIO (PREAMP) LINE LEVEL

MONITOR AUDIO

CLOVIS SERVER

HUB

ROUTER

1 OR MORE PCs NEW YORK

SERVER

HUB

ROUTER

1 OR MORE PCs

VIDEO

VIDEO

COM2: RS232

COM1: RS232/422/485

COM2: RS232

COM1: RS232/422/485

18 C2907M-D (4/05)

Figure 11. WAN Box-To-Box Connection (Transmitter, Receiver, Spectra)

CLOVIS SERVER

HUB

ROUTER

1 OR MORE PCs NEW YORK

SERVER

HUB

ROUTER

1 OR MORE PCs

Video Out

75 Audio I/O

Power

Video In

75 Audio I/O

Power

TRANSMITTER

RECEIVER SPECTRA

AUDIO (PREAMP) LINE LEVEL

DATA

DATA

MONITOR AUDIO KEYBOARD

VIDEO

COM2: RS232

COM1: RS232/422/485

COM2: RS232

COM1: RS232/422/485

C2907M-D (4/05) 19

Figure 12. WAN Box-To-Box Connection (Transmitter, Receiver, Spectra, Genex)

Video In

75 Audio I/O

Power

TRANSMITTER

SPECTRA

DATA

VIDEO

GENEX

Video Out

75 Audio I/O

Power

RECEIVER

DATA

MONITOR KEYBOARD

VIDEO

CLOVIS SERVER

HUB

ROUTER

1 OR MORE PCs NEW YORK

SERVER

HUB

ROUTER

1 OR MORE PCs

COM2: RS232

COM1: RS232/422/485

COM2: RS232

COM1: RS232/422/485

20 C2907M-D (4/05)

Figure 13. WAN Browser-To-Box Connection (Transmitter, Browser, Fixed Camera)

Figure 14. WAN Browser-To-Box Connection (Transmitter, Browser, Spectra)

CLOVIS SERVER

HUB

ROUTER

1 OR MORE PCs NEW YORK

SERVER

HUB

ROUTER

1 OR MORE PCs

Video In

75 Audio I/O

Power

TRANSMITTER

BROWSER

CAMERA

VIDEOVIDEO

COM2: RS232

COM1: RS232/422/485

CLOVIS SERVER

HUB

ROUTER

1 OR MORE PCs NEW YORK

SERVER

HUB

ROUTER

1 OR MORE PCs

Video In

75 Audio I/O

Power

TRANSMITTER

BROWSER

VIDEOVIDEO

COM2: RS232

COM1: RS232/422/485

SPECTRA

C2907M-D (4/05) 21

Figure 15. WAN Browser-To-Box Connection (Transmitter, Browser, Spectra, Genex)

Figure 16. Connection with Pelco Keyboard Control Through a PC (Example Shown with Spectra and Genex)

CLOVIS SERVER

HUB

ROUTER

1 OR MORE PCs NEW YORK

SERVER

HUB

ROUTER

1 OR MORE PCs

BROWSER

Video In

75 Audio I/O

Power

TRANSMITTER

SPECTRA

DATA

VIDEO

GENEX

COM2: RS232

COM1: RS232/422/485

75

Audio I/O

COM2:

RS232

Power

TRANSMITTER

SPECTRA

DATA

VIDEO

Video In COM1:

RS232/422/485

GENEX

PV140

1

2

3

4

8

7

6

5

12 VAC

KBD200A/ KBD300A

RX-

RX+

STRAIGHT CABLE

ETHERNET CONNECTION TO NETWORK (LAN/WAN)

PC WORKSTATION

PELCO KEYBOARD

TX -

TX +

RX -

RX +

GN D

12 V

12VDC

22 C2907M-D (4/05)

Hardware Installation Refer to Appendix A for examples of how to connect equipment.

MOUNTING THE NET350 TO THE WALL

Figure 17. Securing NET350 to Wall Mount Bracket

If desired, the NET350 can be mounted to a wall using the supplied wall mount bracket. To do so:

1. Pry off the clear plastic feet from the bottom of the NET350 unit. (Note the grooves on the underside of the unit. They are involved later in securing the unit to the wall mount bracket.)

2. Refer to Figure 17. Align the grooves on the underside of the NET350 with the four smaller holes in the mount. Install four screws (supplied) through the holes in the bottom of the wall mount. The screws t in the grooves. Tighten carefully to secure the NET350 to the wall mount. DO NOT OVER-TIGHTEN; the screws can damage the aluminum grooves.

3. Attach the mount to the wall with four screws (customer supplied) through the mounts oblong holes. The mount can be attached to the wall with any side of the NET350 pointing up.

CONNECTING VIDEO SOURCES OR DISPLAYS The BNC Video In socket of the NET350T transmitter accepts color or black-white sources and automatically detects whether it is PAL or

NTSC. The video input has an external switch for termination of 75 ohms.

The Video Out BNC socket of the NET350R receiver can be connected to any PAL or NTSC video monitor or VCR with a composite PAL or NTSC input. You must select NTSC or PAL on the conguration page for video decoder settings for the NET350R.

If the video signal is not looped through, terminate the video input by setting the 75 slide switch (located on the front of the transmitter) to the right.

C2907M-D (4/05) 23

CONNECTING DATA TERMINALS The bidirectional data interface ports can be used as control ports for equipment connected to the NET350 (for example, a dome camera with motorized lens).

The COM1: RS232/422/485 port supports RS-232, RS-422, and RS-485 transmission protocols.

The COM2: RS232 port supports RS-232 transmission protocols.

PIN ASSIGNMENTS

NOTE: Transmission of transparent data is only possible when a video connection has been established.

CONNECTING AUDIO EQUIPMENT The NET350 provides an audio channel through the Audio I/O jack. The audio signals are transmitted bidirectionally and simultaneously with the video signals. This allows control of a loudspeaker or door intercom system as required. Bidirectional, full duplex audio applies to box-to-box connections only.

1. Connect a preamplied microphone (monaural line) to the Audio I/O jack on the transmitter.

2. Connect a loudspeaker to the Audio I/O jack on the receiver.

Figure 18. Connecting Audio Equipment

Table A. Pin Assignments

COM1 COM2 Pin RS-232 RS-422/485 RS-232

1 DCD (data carrier detect)

2 RX (receive data) RX+ (receive data plus) RX (receive data)

3 TX (transmit data) TX- (transmit data minus) TX (transmit data)

4 DTR (data terminal ready)

5 GND (ground) GND (ground) GND (ground)

6 DSR (data set ready)

7 RTS (ready to send) TX+ (transmit data plus)

8 CTS (clear to send) RX- (receiver data minus)

9

WARNING: Pay attention to documentation relating to the installation and operation of the equipment being controlled.

1 2 3 4 5

6 7 8 9

GND In Out

24 C2907M-D (4/05)

CONNECTING AN ALARM The NET350 has an alarm input that lets you connect an external signaling device, such as a door contact or motion detector. (Note that there is no motion alarm on a NET350 receiver.) If congured accordingly, an alarm trigger can also set up an automatic connection between the NET350 and the remote station. You can connect switches or contacts directly without a separate power supply.

Do the following to connect an external sensor. Refer to Figure 19.

1. Pull the Alarm I/O terminal block from its plug-in base.

2. Attach conductors to the alarm input and ground conductor terminals. (Insert a small screwdriver tip in the square hole and push hard enough to open the corresponding round hole. Insert the wire in the round hole.)

3. Push the terminal block back on to the plug-in base.

Figure 19. Alarm and Relay Connections

ALARM IN

ALARM OUT ANALOG IN (NOT USED)

POWER OUT, 3.3 VDC 50 mA

GND

GND

GND ALARM OUT

30 VDC 800 mA MAX.

C2907M-D (4/05) 25

CONNECTING A RELAY The NET350 has a relay for switching an external device (for example, a light or siren). The relay can be operated from a control page during an active connection or automatically to coincide with certain events. Settings for the relay must be congured (refer to the Conguration section).

Do the following to connect a peripheral device (such as a light) that can be activated from a PelcoNet live video page. Refer to Figure 19.

1. Pull the Alarm I/O terminal block from its plug-in base.

2. Connect the Alarm Out terminal on the top of the block to an external power source and the component to be activated (for example, a light or buzzer). Then use the second wire to connect the Alarm Out terminal on the bottom of the block to the external power source and the component. (Insert a small screwdriver tip in the square hole and push hard enough to open the corresponding round hole. Insert the wire in the round hole.)

3. Push the terminal block back on to the plug-in base.

CONNECTING TO A LAN Refer to Figure 20. You can connect the NET350 to a 10/100BASE-T network either directly or through a hub. To do so, plug a standard Cat5 UTP cable with RJ-45 connectors into the NET350s Ethernet socket.

Figure 20. Connecting to the LAN Port

SWITCHING ON POWER There is no power switchthe unit is ready for operation when it is plugged into an outlet. Do not connect the NET350 to a power source until all other connections have been made.

1. Plug the supplied cable into the NET350s Power socket.

2. Plug the adapter end into an outlet grounded to earth.

The Power LED is red during start-up and turns green when the NET350 is ready to operate. If the network connection is established correctly, the L LED turns green. A ashing yellow T LED means data is moving over the network.

WARNING: The maximum rating of the relay contact is 30 VDC and 1 A.

Compact Flash

Alarm I/O Ethernet Power

L TOI

26 C2907M-D (4/05)

Conguration

BOX-TO-BOX CONNECTION The following explains a box-to-box connection.

1. First, transmitter and receiver need to be congured appropriately. If the units are supposed to be operated in different subnets, a gateway IP address must be congured. Use the Live video receiver IP address eld to address the destination. Enter the settings using either a terminal program or a web browser.

2. Once all addresses are congured, under the terminal program menu, go into the Rcp+ menu and type e to make the connection. Or program the live video receive IP address and enable the live auto connect setting through the web browser. Make sure the unit that will initiate the connection has an alarm IP address that points to the destination unit. After a few seconds, video transmission begins and the camera scene appears on the monitor attached to the receiver.

Instead of using a terminal program or web browser for establishing a connection, you can attach a contact to the alarm input. Make sure the alarm input eld on the conguration page for alarm settings is enabled and the connect on alarm eld is turned on.

You can use a web browser to connect to either of the two units, even during an active box-to-box connection. This way you can make changes to the conguration and immediately see the result of the setting (for example, when changing video quality). (This is not true for passwords, however.) If you are connected to the transmitter, the camera pictures are sent to the receiver and web browser simultaneously. There will be a short break in the video display on the receiver monitor whenever the web browser requests a new frame. This is especially noticeable with the Server Push feature.

Transparent data is always transmitted automatically between the two units as soon as the connection becomes active. Data bytes entering the interface are transported to the other end transparently. There is no ow control mechanism for the data channel. Overowing the serial interface will cause data loss.

To sever the connection from either end, in the Rcp+ menu press 3 (or disable the alarm).

CONFIGURATION TYPES There are two ways to congure your system:

A convenient, complete conguration and display of video is accomplished through the built-in HTTP server, which connects to any standard web browser (for example, Internet Explorer). You can then congure using screens and menus. This is the recommended method. Refer to the Conguration Using a Web Browser section.

The most basic conguration is accomplished by connecting a PC to the RS-232 terminal port. You then type in commands and parameters. Refer to the Conguration Using a Terminal Program section.

CONFIGURATION USING A WEB BROWSER To use a web browser the system features a complete HTTP server.

Microsofts Internet Explorer 5.5 or higher is the recommended browser.

In order for live video images to be decoded, the special ActiveX control le must be installed on your PC. The latest version of the ActiveX platform comes on the PelcoNet CD. Also, the unit will not function without some form of Microsofts Virtual Machine installed on the PC. Virtual Machine is included on the PelcoNet resource CD that came with your NET350 unit.

C2907M-D (4/05) 27

GETTING STARTED

NOTES:

NET-Manager is a program that can make it easier to manage PelcoNet units in local networks. The program and manual (C2901M) are on the resource CD that comes with your PelcoNet unit. Refer to the manual for instructions.

The only NET-Manager features available to the NET350 include scanning to see your units IP and MAC addresses, changing IP addresses, and viewing the setup pages with the browser.

1. Start your web browser.

2. Connect to the URL http://IP-Address, where IP Address is the IP address of the unit you want to congure. Use the standard dot- separated format (x.x.x.x) to enter the address. The home page is displayed along with the video from the camera.

Figure 21. PelcoNet Home Page

The home page is the starting point for any conguration.

The window in the left of the screen is the display area for decoded video.

Clicking the Pelco logo on any page connects you to the Pelco Internet home page, provided the LAN supports Internet access.

Click Video 1 or Video 2 to choose which live display to view.

Click Server Push for periodically updated stills.

Click Control to access an options screen with links to pages where you can see and control the displayed view. (Refer to the Web Browser Control Pages section.)

Click Setup to access an options screen with links to conguration pages. Click any icon on the side or the text itself to transfer to the desired page.

28 C2907M-D (4/05)

Figure 22. PelcoNet NET350 Menu Tree

HOME

VIDEO 1

VIDEO 2

SERVER PUSH

CONTROL

SETUP

MEDIA REPLAY

GENEX MUX WITH LIVE VIDEO 1

GENEX MUX WITH LIVE VIDEO 2

GENEX MUX WITH MJPEG SERVER PUSH

SPECTRA DOME SYSTEM WITH LIVE

VIDEO 2

ESPRIT SYSTEM WITH LIVE VIDEO 1

ESPRIT SYSTEM WITH MJPEG SERVER PUSH

ESPRIT SYSTEM WITH LIVE VIDEO 2

TIME RECORDING

ALARM RECORDING

PROPERTIES

PARTITION SCREEN

SPECTRA DOME SYSTEM WITH LIVE

VIDEO 1

GENERAL UNIT NAME UNIT ID PASSWORD LEVEL PASSWORD PASSWORD CONFIRM DATE FORMAT UNIT DATE UNIT TIME TIME ZONE TIME SERVER IP ADDRESS HARDWARE VERSION SOFTWARE VERSION SOFTWARE UPLOAD UPLOAD PROGRESS CONFIGURATION DOWNLOAD CONFIGURATION UPLOAD

VIDEO CAMERA CAMERA NAME STAMPING TIME STAMPING VIDEO WATERMARKING MPEG-4 DISPLAY ALARM STAMPING DISPLAYED ALARM MESSAGE NAME OF (FIRST/SECOND)ENCODER PARAMETER PRESET PRESET PARAMETER NAME DATARATE VIDEO QUALITY SETTINGS INTRA FRAME DISTANCE FRAME SKIP RATIO VIDEO RESOLUTION FIELD MODE RESET THIS PARAMETER PRESET MPJEG

ALARM

VIDEO MOTION ALARM UNIFIED PICTURE DETECTION VIDEO LOSS ALARM ALARM INPUT CONNECT ON ALARM NUMBER OF VIDEO RECEIVER ADDRESS LIVE VIDEO RECEIVER IP ADDRESS REMOTE RECEIVER PASSWORD LIVE VIDEO AUTO-CONNECT

RELAY IDLE STATE OPERATING MODE RELAY FOLLOWS RELAY NAME TRIGGER RELAY

NETWORK UNIT IP ADDRESS SUBNET MASK GATEWAY IP ADDRESS VIDEO/AUDIO TRANSMISSION MULTICAST STREAMING MULTICAST GROUP IP ADDRESS MULTICAST VIDEO PORT ENCODER 1 MULTICAST AUDIO PORT ENCODER 2

MPEG-4 MULTICAST PACKET TTL MULTICAST AUDIO PORT

INTERFACE COM 2 SERIAL PORT FUNCTION BAUD RATE DATA BITS STOP BITS PARITY CHECK

SERIAL PORT FUNCTION BAUD RATE DATA BITS STOP BITS PARITY CHECK INTERFACE MODE HALF-DUPLEX MODE GENEX PROTOCOL ID SPECTRA/ESPRIT PROTOCOL ID

INTERFACE COM 1

MEDIA PLAYBACK SCREEN

MOTION DETECTION

MOTION DETECTOR SELECT SENSOR FIELD MOTION TRACKING TRACKER LOCAL SENSITIVITY AVERAGE N [FRAMES] OBJECT MIN SIZE [N*N BLOCKS] ALARM INDICATOR THRESHOLD

MOTION DETECTOR GRID

MATRIX CONTROL WITH LIVE VIDEO 2

MATRIX CONTROL WITH LIVE VIDEO 1

MATRIX CONTROL WITH MJPEG

SERVER PUSH

SPECTRA DOME SYSTEM WITH

MJPEG SERVER PUSH

MEDIA RECORDING

KEYBOARD CONTROL WITH LIVE VIDEO 1

KEYBOARD CONTROL WITH LIVE VIDEO 2

KEYBOARD CONTROL WITH MJPEG SERVER PUSH

COM PORT BAUD RATE DATA BITS STOP BITS PARITY

KEYBOARD

ENABLE AUDIO ENCODER

AUDIO

C2907M-D (4/05) 29

SETUP PAGE

Figure 23. PelcoNet NET350 Setup Page

NOTE: The Set button within a box on a conguration page applies to all the elds within that box. You can change all the elds in a box and then click Set once and all the changes within that box will be saved.

All conguration items are stored in nonvolatile memory so they are kept when the unit is powered down.

Some congurations apply only to transmitters (for example, camera settings) while others apply to both transmitters and receivers. The conguration pages for receivers do not include elds that apply only to transmitters.

30 C2907M-D (4/05)

CONFIGURATION PAGE FOR GENERAL SETTINGS

The unit identication, password, date and time, time server, version information, and software update settings make up the General Settings conguration page.

All units have a real-time clock set during manufacture. However, time and date can be changed anytime; for example, when the units are operated in different time zones.

Version numbers for the hardware and rmware are for information only. Whenever you need technical support, have these numbers ready.

Figure 24. Conguration Page for General Settings

C2907M-D (4/05) 31

Conguration Item

Default Setting Description

Unit name None (For future development.) The Unit name identies the device; for example, in the event of an alarm, this name would be displayed in the video image, depending on the conguration. You can enter up to 31 alphanumeric characters.

Unit ID None (For future development.) The Unit ID identies the device. You can enter up to 31 alphanumeric characters.

Password level None Select the password level from the pull-down menu.

Access to the NET350 generally is protected with a password to prevent unauthorized use of the unit. There are three password levels.

Service: This is the administrative, and highest, level. This level grants access to all conguration parameters after the current password is entered.

IMPORTANT: Service is an administrative account. If you do not set up a Service password, there is no point in setting up User or Live passwords because a user can log in to the unit by entering service and then eliminate the User and Live passwords.

User: This is the second highest level. This level lets the user view live video and access the control pages.

Live: This is the lowest level. This level does not grant access to conguration pages but allows the unit to be operated (for example, viewing video).

If any password level is set, you will always be required to log on to the NET350.

For example, if a Live level password is set and you view that unit through the browser, the unit will ask for a user name and password to access any conguration page. If you then try to access the setup page again, the unit will again prompt for a user name and password.

Some scenarios that can occur are as follows:

If a password is set for the Service level, then the only way to access the setup page is by logging on using the Service user name and the Service level password.

If no password is set for the Service level, then you can log on with the Service user name and no password or you can log on with the Live user name and the Live password you have selected.

Password None You can enter or change a password if the unit is accessed in the Service authorization level or if the unit is not pro- tected by a password. Passwords can be changed one at a time only (that is, either Service, User, or Live). Maximum entry is 19 alphanumeric characters. All entered characters will be saved when you click Set; however, no more than eight asterisks will be displayed when you access the screen next time even if you entered more than eight characters.

Password conrm None Re-enter the new password again to guard against typing errors. If the device is not protected by a password, the No password set message will be displayed.

Date format Europe Use the pull-down menu to select the format for the date: Europe, USA , or Japan.

Unit date N/A Enter the current date in MM/DD/YYYY format for the USA, DD.MM.YYYY for Europe, or YYYY/MM/DD for Japan. This is the system date, which is controlled by an internal real-time clock. The day of the week (rst entry box) need not be entered and will be automatically adjusted based on the given date.

Unit time N/A Enter the current time or click the Synchr. PC button and then click Set to synchronize the NET350 with your com- puters system time. This is the system time, which is controlled by an internal real-time clock. This only synchronizes once. (Pelco cannot guarantee the time will be accurate without the use of a time server.)

Time zone Pacic Use the pull-down menu to select the time zone for the NET350. This and the Timer Server IP Address settings are important if the internal clock should be synchronized with the time received from a time server on the Internet.

Time server IP address

0.0.0.0 Enter the IP address of a TIME protocol server and then click Set. The time and date are automatically synchronized every two hours to this server. This feature does not adjust for Daylight Saving Time; you should adjust manually as needed.

Hardware version N/A Read-only version number of the hardware. This contains unique serial number, type of hardware, and revision.

Software version N/A Read-only rmware version number. This is important information should you need technical support.

WARNING: Setting a User level password on a transmitter can cause complications on the receiver side in a box-to-box conguration. To avoid this, on the receivers Alarm Settings conguration page enter the transmit- ters IP address and user password in the appropriate elds (live video receiver IP address and remote receiver password). If no User level password is set on the transmitter, then the receiver needs no setup.

32 C2907M-D (4/05)

CONFIGURATION PAGE FOR MPEG-4 VIDEO SETTINGS

MPEG-4 encoder and live page settings make up the conguration page for MPEG-4 video settings. The table that follows describes conguration items.

Figure 25. Conguration Page for MPEG-4 Video Settings (Only One Example Shown)

NOTE: The receiver monitor displays only Encoder 1 settings; Encoder 2 settings are not displayed.

Software upload N/A Units have ash EPROMs for rmware upgrades in the eld. These upgrades can be done directly from the web browser. Enter the name of the le containing the upgrade, or locate it using the Browse button. Then click the Upload button.

Upload progress 0% This eld shows the percentage of the upload that has been completed.

Conguration download

N/A Clicking the Download button saves the current conguration of the PelcoNet NET350 transmission system to a PC le.

Conguration upload N/A This copies a le from a PC to the NET350. Enter the name of the le containing the conguration, or locate it using the Browse button. Then click the Upload button to overwrite the conguration with the conguration stored in the named le.

Conguration Item

Default Setting Description

C2907M-D (4/05) 33

Conguration Item

Default Setting Description

Camera Camera 1 Enter a camera name.

Camera name stamping

Off Use the pull-down menu to select a screen option (Top or Bottom) where the camera name will be displayed. Or select Off.

Time stamping Off Use the pull-down menu to select a screen position (Top or Bottom) where the current time will be displayed. Or select Off.

Video watermarking MPEG-4

On Use the pull-down menu to select whether the MPEG-4 data stream will be stamped with a watermark (On) or not (Off). A green rectangle will be stamped on the decoded signal of the validated data stream.

Display alarm stamping

Off Use the pull-down menu to select whether a message will be displayed in the event of an alarm.

Displayed alarm message

N/A Enter the message to be displayed in the event of an alarm (31 alphanumeric characters maximum).

MPEG-4 Encoder 1/2 (tab)

MPEG-4 Click the tab to choose whether to set parameters for either encoder 1 or encoder 2. The Encoder 1 selected buttons text will be bold.

Name of (rst or sec- ond) encoder

(Name of rst

encoder)

Clicking the MPEG-4 Encoder 1 or 2 tab changes the title of, and entry in, this eld. If desired, enter a name other than the programmed name to identify video 1 or video 2 (24 alphanumeric characters maximum). (Changing the name here also changes it on the tab.)

Parameter preset 1 Use the pull-down menu to select a setting (1-8) that corresponds to a predened prole in the Preset Parameter Name eld below. The prole changes as you change the setting. These predened proles are a starting point from which you can make custom adjustments, if desired.

Preset parameter name

high res.

(4CIF)

This eld describes the prole associated with the setting in the Parameter Preset eld above. This eld changes automatically. The proles are predened and optimized for different transmission paths. The proles are

1 = high res. (4CIF) for connections with high bandwidth and high resolution of 704 x 576 pixels

2 = low delay (half D1) for connections with high bandwidth and motion-optimized resolution of 352 x 448 pixels

3 = low bandw. (CIF) for connections with lower bandwidth and resolution of 352 x 288 pixels

4 = DSL for ADSL connections

5 = ISDN (2B) for ISDN connections over two B channels

6 = ISDN (1B) for ISDN connections over one B channel

7 = MODEM for modem connections

8 = GSM for GSM modem connections

(Note that QCIF does not support displaying camera name stamping, time stamping, and display alarm stamping.)

Datarate 5000 The data rate gure in this eld changes automatically according to the setting you choose in the Parameter Preset eld.

Video quality settings

Auto This setting adjusts the value between video quality and image frame rate. Use the pull-down menu to choose either Auto or Manual.

If you choose Auto, an optimized value is adjusted automatically.

If you choose Manual, you can change the value between high quality and low quality on the slide bar at the right.

Intra frame distance 0 Enter a value to change the size of the frames within the MPEG-4 video stream.

Frame skip ratio 1 Enter a skip value for images.

If you enter 1, all images are encoded.

If you enter 2, every second image is encoded. Use this setting if you want low bandwidth and higher quality.

Video resolution CIF Use the pull-down menu to choose the video resolution (QCIF, CIF, 2CIF, 4CIF, or custom) for viewing and recording. See the Preset Parameter Name eld for descriptions of options.

Field mode Interlaced This setting lets you select the eld mode for video transmission. Use the pull-down menu to select one of the following:

Interlaced Interlaced mode on. Setting improves video quality on moving objects.

Progressive Interlaced mode off.

Reset this parameter preset

N/A Click the Default button to return the settings to the factory defaults.

34 C2907M-D (4/05)

CONFIGURATION PAGE FOR VIDEO DECODER SETTINGS (RECEIVER ONLY)

Just two elds video monitor name and video output standard make up the conguration page for video decoder settings. The following table describes conguration items.

Figure 26. Conguration Page for Video Decoder Settings (Receiver Only)

Video monitor name N/A Enter a name (31 characters maximum for the monitor).

Video output standard NTSC For devices that also function as receivers, select the video standard for the monitor output (NTSC or PAL). Reset the unit if you change this value.

C2907M-D (4/05) 35

CONFIGURATION PAGE FOR AUDIO SETTINGS

Figure 27. Conguration Page for Audio Settings

Conguration Item

Default Setting Description

Enable audio encoder

Off Use the pull-down menu to turn on/off audio.

36 C2907M-D (4/05)

CONFIGURATION PAGE FOR ALARM SETTINGS

The PelcoNet NET350 transmission system is not only a multimedia gateway but also a security device and, therefore, has many features related to security applications. The conguration page for alarm settings lets you congure your unit for surveillance applications. In most surveillance- related applications, the receiver is located in a secure alarm center-type environment while the transmitter is located at the site to be monitored.

Figure 28. Conguration Page for Alarm Settings

Figure 29. Motion Detection Screen

C2907M-D (4/05) 37

Figure 30. Motion Detection Grid Screen

38 C2907M-D (4/05)

The set of alarm features is explained below.

Conguration Item

Default Setting Description

Video motion alarm N/A The system has a video motion detection feature. The video scene is monitored constantly for relevant motion.

NOTE: Use of the motion detection feature is recommended only indoors and under controlled lighting conditions; it is not recommended in dim lighting.

The following conditions must be met for motion detection to function:

Motion detection must be activated.

At least one cell must be activated.

Sensitivity must be set higher than zero.

To set motion detection, do the following:

1. Click the Motion detection button to access the Motion Detection screen. (Refer to Figure 29.) Click Default to get the default settings for motion detection.

2. Select On from the Motion detector pull-down menu to trigger an alarm in the event of movement.

3. Click the Select area button to display a window with a grid superimposed on it (refer to Figure 30). Select the cells in the image you want the system to monitor for motion. You can use the Select all and Clear all buttons.

The default is all cells selected (red).

To set an individual cell, click it with the left mouse button (it will turn red). Click the right button to deselect a cell (which will turn white). Select or deselect multiple cells by holding down the left or right mouse button and dragging. Release when nished.

Click the Set button.

4. Use the Motion tracking pull-down menu to turn on/off tracking. (Note that motion tracking overrides motion detection.)

5. The Tracker box indicates and controls the direction of motion detection. You can set motion detection to operate in one direction only by removing the check mark in the opposite direction. (This advanced feature must be set up precisely. Pelco recommends extensive setup testing in order to get the expected results.)

6. Use the Local sensitivity slide bar to set detection sensitivity. You need to adapt sensitivity to the respective environment and the acceptable false alarm rate: for a lower false alarm rate select a lower sensitivity and vice versa. Experiment to nd the best setting.

7. Use the Average n [frames] slide bar to dene how much motion must be detected before an alarm will be released. If the value is high, even movement over a small time period triggers an alarm. If the value is low, movement over a longer period is required to trigger an alarm.

8. Use the Object min size [nxn blocks] slide bar to designate the minimum number of cells in the frame a moving object must ll to trigger an alarm. You can set the value between 1*1 and 6*6 (2*2 is recommended). If the size of the object in the picture exceeds the value you set, motion detection triggers an alarm.

9. The Alarm indicator box lets you set a threshold so an alarm is triggered only if the sensitivity of the video sensor is exceeded. Thus, something such as background noise caused by the camera can be ltered to avoid unwanted alarms.

The blue line indicates the alarm threshold. Any value exceeding this produces an alarm signal. Components of the motion signal generating the alarm are indicated in red. Pull up or down on the blue line to observe the motion detector.

10. Click Back to Alarm page! when nished.

Unied picture detection

Off Use the pull-down menu to turn on/off this feature, which gives an alarm when the picture becomes too blurry.

Video loss alarm Off If you select On, the signal from the video source (the camera in most cases) is monitored constantly for interrup- tion. If no signal is received, the NET350 triggers the alarm.

Alarm input Off/High 1. Select On from the pull-down menu if you want to activate an alarm through an external alarm sensor.

2. Select High or Low for the voltage level to activate the alarm.

3. Enter a name for the alarm input to be displayed on the screen if an alarm is activated (31 alphanumeric char- acters maximum).

C2907M-D (4/05) 39

Connect on alarm Off The alarm functions would have little effect without automatically triggering corresponding actions. Select On for automatic connection to the video receivers IP address. The idea is to provide a remote monitoring station with live video in case of an alarm. (If you want both motion and alarm input to activate an alarm, set this eld to On. If set to motion only, motion alarms will activate an alarm but no input alarms will be recognized.)

This feature can be useful even for many applications not related to alarm conditions. One example is a video- equipped door entry system: when the doorbell is pressed, a contact closes and the connected transmitter automat- ically connects to a receiver. Full duplex audio can provide verbal communication, while the relay output can open the door remotely.

Select Follows input to specify that the connection remain as long as the alarm is active. (If Follows input is set, motion will not activate an alarm.) Select Follows motion alarm to specify that the alarm will turn on when motion is detected and turn off 10 seconds after motion is no longer detected. (If Follows motion alarm is set, input will not activate an alarm.)

Number of video receiver address

1 The NET350 can store up to 10 different alarm IP addresses. When an alarm occurs, a connection is established to the rst address. Up to 10 separate addresses can be added should the rst address not accept the call.

Use the pull-down menu to select how many additional addresses to contact, if necessary. (Add the IP addresses in the next eld.)

Live video receiver IP address

0.0.0.0 Enter the IP addresses (10 maximum) of the receivers to be notied in the event of an alarm.

Remote receiver password

N/A Enter the password for the remote unit if it is protected by a User or Live password.

Live video auto-connect

Off Select On if at each restart an active connection should be set up automatically to the receivers IP address. The auto-connect feature guarantees an active connection to the receivers alarm IP address even after connection breakdown or network failures. As soon as communication is restored, the connection is reinstated. On a receiver, this feature is enabled to establish a connection to a transmitter automatically.

Conguration Item

Default Setting Description

WARNING: Setting a User level password on a transmitter can cause complications on the receiver side in a box-to-box conguration. To avoid this, on the receivers Alarm Settings conguration page enter the transmit- ters IP address and user password in the appropriate elds (live video receiver IP address and remote receiver password). If no User level password is set on the transmitter, then the receiver needs no setup.

40 C2907M-D (4/05)

CONFIGURATION PAGE FOR RELAY SETTINGS

You can use the conguration page for relay settings to specify parameters such as normally open or normally closed switching and bistable and monostable operation of the output.

Figure 31. Conguration Page for Relay Settings

Conguration Item

Default Setting Description

Idle state Open Select Open (N.O. at zero current) if the relay will operate as a normally open contact or Closed (N.C. with current) if it will operate as a normally closed contact.

Operating mode Bistable Select the relays operating mode.

When you select the default Bistable mode, the relay will stay in the idle or active state for an indenite period. (For example, select Bistable if a oodlight activated by an alarm is to remain switched on at the end of the alarm.)

When you select a time period (monostable mode), the relay automatically falls back to the idle state after a predened period expires. (For example, select 10 s if a siren triggered by an alarm is to sound for 10 seconds.) The choices on the pull-down menu are Bistable, 0.5 s, 1 s, 2 s, 5 s, 10 s, and 60 s.

Relay follows Off Select from the pull-down menu an event that will activate the relay. A typical application is to have the relay follow the status of the alarm input; for example, to power peripheral equipment or even the camera itself. Select from the following:

Off: Relay does not operate.

Connection: Relay operates whenever you open live video and will turn off when you exit live video.

Video alarm: Relay operates when there is loss of the video signal.

Motion alarm: Relay operates when there is motion alarm.

Local input: Relay operates by an external alarm sensor.

Remote input: Relay operates by a switching contact from a remote location.

Relay name Relay 1 Enter a name for the relay that will appear on the Live page (31 alphanumeric characters maximum).

Trigger relay N/A Click the Relay button to switch the relay manually (for example, as a test or to allow a door to be opened).

C2907M-D (4/05) 41

CONFIGURATION PAGE FOR COM 1 INTERFACE SETTINGS

You can use this conguration page to set the parameters of the COM 1 RS-232/422/485 serial interface port.

Figure 32. Conguration Page for COM 1 Interface Settings

Conguration Item

Default Setting Description

Serial port function Terminal Use the pull-down menu to select a controllable device from the pull-down menu: Terminal, Transparent, or Pelco Prot (protocol).

If the port must transmit data transparently, select Transparent. You can use Pelco Prot to send any kind of con- trol data for a Spectra, Esprit, Genex, or a Pelco matrix.

Baud rate 19200 Use the pull-down menu to select a transmission rate from 600 to 115200 baud. Refer to Appendix A for settings.

Data bits 8 The number of data bits is set at 8 per character.

Stop bits 1 Use the pull-down menu to select the number of stop bits (1 or 2) per character. Refer to Appendix A for settings.

Parity check None Use the pull-down menu to select the type of parity check (None, Even, or Odd). Refer to Appendix A for settings.

Interface mode RS232 Use the pull-down menu to select the required protocol for the port (RS232 or RS422/485). Use RS-232 for two-wire communication (TXD and RXD) and RS-422 for four-wire communication (TX+, TX-, RX+, RX-). (RS-485 is not normally used except in advanced applications.)

Half-duplex mode Off This mode allows NET350 to receive data only and not transmit data. If you choose this RS-232 mode, by selecting On, camera control data is transferred automatically to COM 1, which is a serial interface on the units rear panel to which you can connect a PC. This mode supports data ow control. (Refer to Table A.)

Buffered mode also transfers data input to COM 1.

Depending on the equipment used, the Serial Port Function eld may have to be set to Transparent if sending any control data.

Genex protocol ID N/A Enter the address of the Genex unit with which you want to communicate.

Spectra/Esprit protocol ID

N/A Enter the address of the Spectra or Esprit unit with which you want to communicate. This must match the P-protocol address of the Spectra or Esprit unit.

42 C2907M-D (4/05)

CONFIGURATION PAGE FOR COM 2 INTERFACE SETTINGS

You can use this conguration page to set the parameters of the COM2 RS-232 serial interface port.

Figure 33. Conguration Page for COM 2 Interface Settings

Conguration Item

Default Setting Description

Serial port function Terminal Use the pull-down menu to select the function for serial port 2 from the pull-down menu: Terminal, Transparent, or Pelco Prot (protocol).

If the unit will be operated from a terminal, select Terminal. If the port must transmit data transparently, select Transparent. You can use Pelco Prot to send any kind of control data for a Spectra, Esprit, Genex, or a Pelco matrix.

Baud rate 19200 Use the pull-down menu to select a transmission rate from 600 to 115200 baud. Refer to Appendix A for settings.

Data bits 8 The number of data bits is set at 8 per character.

Stop bits 1 Use the pull-down menu to select the number of stop bits (1 or 2) per character. Refer to Appendix A for settings.

Parity check None Use the pull-down menu to select the type of parity check (None, Even, or Odd). Refer to Appendix A for settings.

C2907M-D (4/05) 43

CONFIGURATION PAGE FOR LOCAL COM INTERFACE KEYBOARD

You can use this conguration page to set the parameters for a local Com port so you can connect a Pelco keyboard to your computer. This lets you control a device through the keyboard; for example, a camera can be controlled from the browser with the Pelco keyboard. You can also use this feature to transmit serial data from your computer to the PelcoNet unit, or vice versa.

Figure 34. Conguration Page for Local Com Interface Keyboard

To use this feature, do the following:

1. On the PelcoNet NET350 Setup Page (Figure 23), select Local Com Interface Keyboard. Then select the parameters (Com port, baud rate, etc.) as listed in the table above.

2. You must also change the local PCs Com port conguration (Start > Settings > Control Panel > Administrative Tools > Computer Management > Device Manager > Ports [COM & LPT] > COM1 or COM2 [depending on the Com port to which the keyboard will be connected]). The conguration of this Com port should be the same as the conguration at the PelcoNet browser.

3. Connect the Pelco keyboard to the COM interface on your PC. This is the COM port that you designated in step 2. (Refer to Figure 54 in Appendix A for a connection example.) If the keyboard uses RS-422/485, a converter will be required to use it on an RS-232 COM port of your computer.

4. On the PelcoNet NET350 Setup Page (Figure 23), select Interface Settings COM1 or Interface Settings COM2. Use the pull-down menu to set the COM1/COM2 serial data port to Transparent. Also set the baud rate for the connected external device you want to control.

5. Finally, from the Device Controls page (Figure 42), select Keyboard. This takes you to the Keyboard Control with live video page (Figure 47). The COM port is open and you can send transparent data from your PC COM port to the PelcoNet COM port, and vice versa.

Conguration Item

Default Setting Description

COM port COM1 Use the pull-down menu to designate a free COM port on the PC to which you will connect the Pelco keyboard.

Baud rate 600 Use the pull-down menu to select a transmission rate from 600 to 115200 baud. Refer to Appendix A for settings.

Data bits 8 The number of data bits is set at 8 per character.

Stop bits 1 Use the pull-down menu to select the number of stop bits (1 or 2) per character. Refer to Appendix A for settings.

Parity None Use the pull-down menu to select the type of parity check (None, Even, or Odd). Refer to Appendix A for settings.

44 C2907M-D (4/05)

CONFIGURATION PAGE FOR NETWORK SETTINGS

Network and routing information make up the conguration page for network settings. These settings are used to integrate the NET350 into an existing network. The table that follows describes the conguration items.

Figure 35. Conguration Page for Network Settings

Conguration Item

Default Setting Description

Unit IP address 10.0.0.1 (transmit-

ter) or 10.0.0.2

(receiver)

Enter a unique IP address that is valid for your network. The precongured default IP address allows for easy con- guration in closed environments. You can use a cross-over cable to connect directly to a PC.

NOTE: Changing the IP address also affects the current browser connection. You will have to reset the NET350 and enter the new URL to regain connectivity to the unit.

Subnet mask 255.255.0.0 Enter a valid subnet mask for your network.

Gateway IP address 0.0.0.0 Enter the IP address of the router if the unit is to establish a connection outside of the local network. This is typically used in a WAN environment. This eld can otherwise remain empty (0.0.0.0).

Video/Audio transmission

UDP Use the pull-down menu to select the means of transmission. Select TCP (Port 80) to send data through a firewall. Select UDP for communication between local networks.

Multicast streaming Off Use the pull-down menu to select MPEG-4 for multicast streaming mode.

Besides a one-to-one connection between a transmitter and a receiver (unicast), the NET350 lets you connect a number of receivers to receive the video signal simultaneously. This is achieved by distribution of a single data stream on the network itself to a number of receivers in a dened group (multicast).

With MPEG-4 selected and a valid multicast group address selected in the Multicast Group IP Address eld, the NET350 operates in multicast mode (data stream duplicated over the network).

When multicast streaming is turned off, operation resorts to unicast mode.

Multicast group IP address

0.0.0.0 This is the Multicast IP address. (Network hardwaresuch as switches, hubs, routers, etc. must support the multi- casting protocol, ICMP.) This eld sets PelcoNet to use the multicasting protocol, which allows more efcient use of bandwidth. The IP range is 224.0.1.0 through 238.255.255.255.

Some IP addresses may be reserved for system resources. Contact your network administrator for more information.

C2907M-D (4/05) 45

CONFIGURATION PAGES FOR MEDIA RECORDING

Time, alarm, and recording properties information make up these conguration pages. Use these pages to set up local recording onto the NET350 (using the CompactFlash interface). These settings let you congure your unit for different recording situations. The table that follows describes items that appear on all three media recording conguration pages (Time, Alarm, and Properties).

NOTE: The link to these pages will not appear if the unit is powered up without a CompactFlash card inserted. The link appears only after inserting the card and resetting the unit. To reset the unit, type a forward slash (\) and reset at the end of the units address in the Internet Explorer browser address window, and then press Enter.

Multicast video port encoder 1

60000 Enter the port address for the video encoder 1 MPEG-4 data stream.

Multicast video port encoder 2

61000 Enter the port address for the video encoder 2 MPEG-4 data stream.

Multicast audio port MPEG-4

55000 Enter any port greater than 1024 that is not in use.

Multicast packet TTL 1 Enter the number of hops for the packet to live. TTL stands for time to live. This setting denes the lifetime of mul- ticast packages in the network. If multicast trafc is to be transmitted over routers and switches, this setting is important in adjusting the lifetime of the package to the requirements of the network.

Conguration Item

Default Setting Description

Partition selection N/A Use the pull-down menu to select which partition you want to view information about or change.

Stop/Start (buttons) N/A These buttons activate and deactivate time and alarm recording for the selected partitions. Once you click the Start button to activate time or alarm scheduling, you cannot make changes or view other partitions until you stop the scheduler with the Stop button.

Time/Alarm/Properties (tabs)

Time recording

Click a tab to select the desired recording or properties page.

Recording active N/A The disk icon spins to show that recording is taking place currently.

Enter partition settings! (button)

N/A Click this button (located in lower right corner) to access a screen that shows how partition resources are allo- cated; and how much free space remains. (Refer to Figure 36.) From here you can access a wizard to set up par- titions (eight partitions maximum can be set per hard disk), or delete existing partitions.

Add partition button: Click this button to access a wizard that lets you add, name, and designate the values for a partition. A chart on the partition allocation screen will show how resources are divided among the parti- tions.

Delete partition button: Highlight a partition and then click this button to remove the partition.

Click Set when nished, and then click Back to HD Scheduler page! to return to the Time Recording page.

Conguration Item

Default Setting Description

46 C2907M-D (4/05)

Figure 36. Partition Settings Page

Conguration Page for Time Recording

Figure 37. Conguration Page for Time Recording Settings

C2907M-D (4/05) 47

This page lets you set the times to record during a seven day period. Click the Time recording tab to access this page.

Conguration Page for Alarm Recording

Figure 38. Conguration Page for Alarm Recording Settings

This page lets you designate when particular alarms will be active for recording. Click the Alarm recording tab to access this page. (You must rst have at least one alarm selected in the Number of alarms eld on the Properties page to access the Alarm Recording page.)

Conguration Item

Default Setting Description

(time recording sched- uler grid)

N/A This grid allows up to 16 different recording times per day in a seven-day period.

To select a recording time, hold down the left mouse button on the desired starting day and time, and then drag to the desired stopping time and release. You can extend recording time by dragging from the point at which you stopped. A display below the grid shows the exact time.

To deselect a recording time, click the right mouse button on the time to be removed. You cannot shorten the time without clearing the time entirely.

If you wish continuous recording for the entire week, click the Select all button. To clear everything for the week, click the Clear button.

Click the Set button when nished. Then you must click the Start button to activate the scheduler.

Conguration Item

Default Setting Description

(alarm recording scheduler grid)

N/A This screen lets you set times when an alarm will trigger recording. (You must choose either motion alarm or alarm input on the Properties screen rst.)

To select an alarm recording time, hold down the left mouse button on the desired starting day and time, and then drag to the desired stopping time and release. You can extend recording time by dragging from the point at which you stopped. A display below the grid shows the exact time.

To deselect an alarm recording time, click the right mouse button on the time to be removed. You cannot shorten the time without clearing the time entirely.

If you wish continuous recording for the entire week, click the Select all button. To clear everything for the week, click the Clear button.

Click the Set button when nished. Then you must click the Start button to activate the scheduler.

48 C2907M-D (4/05)

Conguration Page for Properties

Figure 39. Conguration Page for Properties Settings

This page lets you see and modify current settings for the partitions. You can change alarm recording options here. Also, it shows information about partition size and remaining recording time.

Click the Properties tab to access this page.

WARNING: Any recordings on a partition will be lost if you change the settings.

C2907M-D (4/05) 49

CONFIGURATION USING A TERMINAL PROGRAM Using a terminal program (for example, the Windows application HyperTerminal) on a computer connected to the COM2: RS232 socket on the NET350s rear panel provides limited conguration and control capabilities.

Do the following:

1. Ensure that the PCs COM port is set up properly (default properties are 19200 baud, 8 bits, no parity, 1 stop bit, ow control none) and that the local terminal echo is disabled.

2. Isolate the NET350 from the network.

3. Connect the COM2: RS232 socket on the NET350 to an unused serial port on the PC (null modem required).

4. After the connection is made, you will be prompted for the case-sensitive user name. The factory default is service.

5. All commands consist of single characters you type inside the terminal window. Enter only one command at a time and do not terminate this input by pressing the Enter key. After entering a value (for example, an IP address), check the entered characters again and only then press Enter to transmit the values to the NET350.

The following section shows a typical session.

Conguration Item

Default Setting Description

Partition name N/A This eld displays the name of the partition selected from the pull-down menu at the top of the screen.

Partition number N/A This eld shows which of eight possible partitions is selected.

Type of recording Linear mode Use the pull-down menu to select either Linear or Ring mode as the type of recording. (In Ring mode, earlier video recordings already on the hard disk are overwritten with current recording when the recording capacity is used up. In Linear mode, recording ceases when the storage capacity of this partition is full until you delete pre- vious recordings to release storage space.)

Video recording high quality (CIF)

Use the pull-down menu to select from one of the available recording options (CIF, 2CIF, QCIF, DSL, ISDN [2B], ISDN [1B], MODEM, or GSM).

Number of alarms 1 Use the pull-down menu to select the number of alarms (0-126) that will be recorded. (For example, if you set 5, then only ve alarms will be recorded.)

Alarm recording time 15 sec (pre-) 45 sec

(post-)

Use the pull-down menus to set how long to record before and after an alarm is received (from 0 and seconds to 3 hours)

Alarm recording on N/A Check either Motion alarm or Alarm input to designate what condition should trigger alarm recording. (You must select one of these in order to use the Alarm Recording scheduler.)

Partition total size N/A This eld shows the total size of the partition selected.

Remaining for recording

N/A This eld shows the approximate recording time remaining in the partition.

Free on this partition N/A This eld shows the space remaining in the partition.

Used alarmtracks from partition

N/A This bar shows how many tracks in the partition have been used for alarm recording. There is one alarm per track.

Used letracks from partition

N/A This bar shows how many tracks in the partition have been used for recording.

Total used size from partition

N/A This bar shows the percentage of the partition that has been used for recording.

50 C2907M-D (4/05)

TYPICAL SESSION

The terminal program main menu appears in the terminal window as shown below.

v video

i IP r RCP+ ? this menu q exit/logout

NOTE: You cannot use backspace during a terminal sessionif you mistype a character, end your entry by pressing Enter and try again. If you see duplicate characters on any entry, the local echo feature of your PCs terminal program is not disabled.

If you are using the terminal to set up the units IP address, just type i and then i again. You are prompted to enter a new IP address. Do so and press Enter.

If you want to establish a live video connection to a remote unit, you have to specify the remote IP address by typing r and then entering the remote IP address.

To establish a connection, go to the main menu, then type r, then type e, and then select either video 1 or video 2. To disconnect, type 2 in the same menu.

C2907M-D (4/05) 51

TERMINAL PROGRAM TRANSMITTER MENU STRUCTURE

The following describes the terminal program transmitter menu structure. The menu items and commands are enclosed in single quotation marks. Do not enter the quotation marks. Information and current settings are displayed to the right of the commands. Refer to the Command Reference section for descriptions of the commands.

Main Menu v video

i IP r RCP+ m misc ? this menu q exit/logout

v Video Menu e encoder settings a adapt std res (e.g., CIF) to NTSC: 1 x leave this menu ? this menu

e Encoder Submenu e select encoder: 1 > start encoder: 1 | stop encoder p parameter set: 1 n parameter set name: high quality (CIF) k min frame dist [1]: 1 r encoder bitrate [kBit]: 5000 Q I quantizer: 8 q P quantizer: 8 i I frame distance: 0 u I update distance: 250 s frame size (res): 3 w custom width: 432 h custom height: 288 d reset to default x leave this menu ? this menu

a Adapt Standard Resolutions submenu

Adapt standard resolutions (e.g., CIF) to NTSC? 0 = no, 1 = yes

i IP Menu

An asterisk (*) means a reset of the NET350 after a change is necessary. Reboot by cycling the power.

i local IP (*): 172.16.0.96

s local subnet mask (*): 255.255.0.0 g local gateway (*): 0.0.0.0 r remote IP: 172.16.0.99

Mac address: 00-07-5f-30-00-3c a auto connect (off) p ping remote IP (off) x leave this menu ? this menu

52 C2907M-D (4/05)

r RCP+ Menu

e select video encoder number: 1 c display connection list 1 connect to alarm IP: 172.16.0.99 2 disconnect all connections 3 G.711 audio: On 4 join stream: 172.16.0.99 x leave this menu ? this menu

m Misc Menu

v get version info x leave this menu ? this menu

TERMINAL PROGRAM RECEIVER MENU STRUCTURE

The following describes the terminal program receiver menu structure. The menu items and commands are enclosed in single quotation marks. Do not enter the quotation marks. Information and current settings are displayed to the right of the commands. Refer to the Command Reference section for descriptions of the commands.

Main Menu

i IP r Rcp+ m misc ? this menu q exit/logout

i IP Menu

An asterisk (*) means a reset of the NET350 after a change is necessary. Reboot by cycling the power.

i local IP (*): 172.16.0.95 s local subnet mask (*): 255.255.0.0 g local gateway (*): 0.0.0.0 r remote IP: 0.0.0.0

Mac address: 00-07-5f-30-00-32 a auto connect (off) p ping remote IP (off) x leave this menu ? this menu

r RCP+ Menu

e select video encoder number: 1 c display connection list 1 connect to alarm IP: 0.0.0.0 2 disconnect all connections 3 G.711 audio: On 4 join stream: 0.0.0.0 x leave this menu ? this menu

m Misc Menu

v get version info x leave this menu ? this menu

C2907M-D (4/05) 53

COMMAND REFERENCE

The following table gives an overview of the available commands.

Table B. Terminal Command Reference

Cmd Description ? This command redisplays (refreshes) the current menu.

> This command turns encoding of video back on.

1 Use this command to connect to the receiver in a box-to-box setup.

2 Use this command to sever all connections to the unit.

3 Use this command to toggle audio on/off to the receiver. The default is on.

4 (Receiver only.) Use this command to join the stream of video from the NET350 transmitter. It establishes a physical box-to-box connection.

a (IP menu) Use this command to toggle auto-connect on/off. The default is off.

a (Video menu) Enter 0 (no) or 1 (yes) to indicate whether to adapt standard resolutions to NTSC (for example, CIF to NTSC).

c Use this command to display a list of physical network connections. This can be through Internet Explorer or a box-to-box connection.

d This command returns the settings on this menu to factory defaults.

e Use this command to select the video you wish to congure or for which you wish to see information. Enter 1 or 2. (Transmitter only.)

g Use this command to enter a new gateway IP address. Type a new gateway address, and then press Enter.

h This command lets you set custom resolution (height: 128 to 240).

i (Encoder submenu) Use this commmand to change the size of the frames within the video stream.

i (IP menu) Use this command to enter a new IP address that PelcoNet will be using on the network. Type the new IP address, and then press Enter.

k Use this command to set minimum frame distance.

| This command shuts off decoding of video from the NET350.

n Use this command to name the encoder presets. Type in the name and press Enter. (Name appears in Internet Explorer.)

p (Encoder submenu) Enter a number (1-8) that corresponds to a predened prole. For example, 1 corresponds to high quality (CIF).

p (IP menu) Use this command to see if a unit can be reached. This pings the IP set in the r menu (remote IP). The unit will respond if it can be reached, or the ping command will time out if it cannot be reached.

q Use this command to adjust the value between frame quality and data rate. Enter a value between 1 and 31. Value 1 has highest I-frame quality with a higher bandwidth while value 31 has lower quality and less bandwidth.

Q Use this command to adjust the value between video quality and the image frame rate. Enter a value between 1 and 31. Value 1 has the highest quality with a lower video frame rate while value 31 is a maximum frame rate at lower quality.

r (Encoder submenu) Use this command to designate the data rate. Enter the data rate gure.

r (IP menu) Use this command to connect to a remote IP. Type the IP address, and then press Enter.

s (Encoder submenu) Enter a number to designate the frame resolution. Enter 2 for QCIF, 3 for CIF, or 6 for 2CIF.

s (IP menu) Use this command to enter a new subnet mask. Type the new subnet mask, and then press Enter.

u Use this command to set the I-frame update distance.

v Displays version information for the unit.

w This command lets you set custom resolution (width: 176 to 704).

x Exits this menu.

54 C2907M-D (4/05)

Operation

LIVE VIDEO AND SERVER PUSH VIDEO PAGES The live video pages show a real-time picture of a camera view with update rates and image quality similar to a box-to-box conguration. It can be congured for bandwidth use and for various image quality settings. (Live video is accessible only through a NET350 transmitter and not through a NET350 receiver.) The Server Push pages show still pictures that are updated periodically, and image quality is xed.

The ve indicators in Table C are located at the top of the live video and live video control pages.

Figure 40. Live Video and Server Push Video Pages

1. To access the PelcoNet NET350 transmission system home page, you must rst connect to the Internet/intranet network and open Internet Explorer (the browser).

2. Then, enter the default address (10.0.0.1 for transmitters or 10.0.0.2 for receivers) in the address box. If this address has been changed, enter the application address. The home page appears.

3. Click either Video 1 or Video 2 or Server Push on the home page.

To exit any page, click an option at the top of the page.

The program displays dialog boxes when you try to view live video under any of the following conditions:

With a browser other than Internet Explorer

Without rst installing ActiveX

Table C. Live Video Page Indicators

Indicator Description MPEG-4 Indicates that live viewing is in MPEG-4 format.

M (motion detector) When motion alarm is triggered, this indicator turns red while the alarm is activated.

V (video alarm) When the video loss alarm is triggered, this indicator turns red until the video returns.

I (input activation) When triggered, this indicator turns red. The name assigned to this trigger and its duration and how it reacts can be assigned on the Alarm page.

R (relay activation) When triggered, this indicator turns red. The name assigned to this trigger and how it reacts can be assigned on the Relay page.

C2907M-D (4/05) 55

When your computer display is not set for 16- or 32-bit color

To change: right click the desktop, and then click Properties, the Settings tab, and select High Color [16 bit] or True Color [32 bit]. For NT, select 65536 Colors.

NOTE: Do not change the video properties while viewing live video. You may get a gray background if you do.

When Microsoft Virtual Machine is not enabled.

To enable: on the Tools menu select Internet Options, select the Advanced tab, locate Microsoft VM, checkmark Java Console Enabled and JIT compiler for virtual machine enabled. Reboot your PC.

With any of these conditions, you can only view the video as a series of still images.

DISPLAYING VIDEO ON A WEB BROWSER The NET350T uses MPEG-4 for transmitting video across the network. This enables transmission to standard web browsers of either live video (Video 1 or 2 mode) or a stream of still images (Server Push mode).

To activate the live video feature, click either Video 1 or Video 2 above the video window on the PelcoNet NET350 transmission system home page (refer to Figure 40). The unit transmits using MPEG-4 format for display in the browser.

To stop live video, click any other option at the top of the page.

To activate the Server Push feature, click Server Push above the video window on the home page. The unit continuously grabs snapshots to be JPEG encoded, transferred, and displayed continuously by the browser.

To stop Server Push, click any other option at the top of the page.

The PelcoNet NET350 transmission system can display live video to an innite number of users at a time (multicasting).

Server Push can support multiple users simultaneously on the same transmitter. Image quality is good with an update rate of one image about every 2 to 10 seconds depending on the number of users and available bandwidth.

Browsers that do not support live video technology can display an update still image or a stream of images in Server Push mode.

Figure 41. PelcoNet NET350 Home Page

56 C2907M-D (4/05)

USING THE AUDIO TRANSMISSION FEATURE OF A LIVE VIDEO PAGE To transmit audio via microphone from your PC to the NET350T, do the following:

1. Connect a microphone that is compatible with your PC to your PCs mic input.

2. Connect a speaker to the NET350Ts Audio I/O port.

3. While viewing live video, press the F12 key on the PC to send audio to the NET350T. Note that while holding down the F12 key, audio from the NET350T will not be heard (half duplex).

WEB BROWSER CONTROL PAGES These pages let you control certain Pelco equipment at your computer through a NET350 transmitter (not through a NET350 receiver).

1. To access the PelcoNet NET350 transmission system home page, you must rst connect to the Internet/intranet network and open Internet Explorer (the browser).

2. Then, enter the default address (10.0.0.1 for transmitters or 10.0.0.2 for receivers) in the address box. If this address has been changed, enter the application address. The home page appears.

3. Click Control to access the Device Controls page.

4. The Device Controls page has underlined links to the control pages. To access, click one.

Figure 42. Device Controls Page

The live video control pages include representations of keys that let you control various functions (in addition to showing the camera display). Use the mouse pointer and click the left mouse button to enable options and operate controls on the screen. Click outside the options to disable a radio button or selection button.

Live video pages let you choose the size of the video viewing area. Click either 352x288 (small) or 704x576 (large) in the Resize Video eld.

Live video pages also let you record and play back camera views on a PCs hard drive. Refer to the Recording and Viewing the Display on a PC and the NET350 section for details.

Server push page displays are similar to live video page displays except the server push page lacks the live page indicators at the top of the page and the recording buttons below the picture.

C2907M-D (4/05) 57

MATRIX LIVE VIDEO/SERVER PUSH PAGE CONTENTS

Figure 43. Matrix Control Page (Live Video Page Shown)

The Matrix Control pages contain the following:

Live video indicators (live video page only)

Ten numbered buttons

CAM (camera) button to select a camera

MON (monitor) button to select a monitor

CLR (clear) button to cancel an entered number

PRST (preset) button to select a preset

PATT (pattern) button to select a pattern

MAC (macro) button to select a group camera sequence (not supported for the CM6700)

STOP button to halt a function

BWD (backward) button to scroll through the cameras in reverse order

FWD (forward) button to scroll through the cameras in forward order

AUX ON button to activate an auxiliary

AUX OFF button to deactivate an auxiliary

ACK button to close a message when progamming a pattern on the CM6700 only

SET check box to use in progamming presets and patterns

The following are arrayed under Lens:

Iris open and close buttons

Focus far and near buttons

Zoom out and in buttons

The following are arrayed under Pan/Tilt:

Eight direction arrow buttons

Home button in the center to return the camera to its home position (preset 1)

In Control or No Control indicates whether you have control of the camera. Note that PTZ functions are temporarily disabled while recording live video. Recording control buttons are beneath the picture (live video page only).

On the Matrix live video control page, you can control the following:

Monitor: To select a monitor, enter the monitor number and then click MON.

Camera: To select a camera, enter the camera number (1-16) and then click CAM.

58 C2907M-D (4/05)

Presets: To program a preset from the Matrix browser page: set the image using the arrow keys, click SET, enter a preset number, and then click PRST. To activate a preset, enter the preset number (1-66) and then click PRST. (You must click the CLR button before activating another preset.)

Patterns: To program a pattern from the Matrix browser page: click SET, click PATT, run your pattern using the arrow keys, and then click PATT again when you are nished. (The CM6700 does not support programming of a pattern from the browser.) To run a pattern, click PATT. To halt, click a pan and tilt button, call a preset, or click STOP. (Clicking STOP will not halt a pattern on the CM6700 and CM6800.)

NOTE: For the CM6700 only, click the ACK button to close the message Send Pattern End Command to Exit when it appears.

Programming menus: To access the programming menus, click 9, 5, SET, and then PRST.

Macros: To start a macro, enter 1 or 2 and click MAC. To stop a macro, select a camera or click a pan and tilt button.

Auxiliaries: To turn on an auxiliary, enter the auxiliary number and then click AUX ON. To turn off, enter the auxiliary number and then click AUX OFF.

GENEX LIVE VIDEO/SERVER PUSH PAGE CONTENTS

Figure 44. Genex Control Page (Live Video Page Shown)

The Genex pages contain the following across the top of the page:

Live video indicators (live video page only)

Main and Spot monitor selection radio buttons

A LIVE/VCR button to toggle main monitor display between live input and playback from a VCR

A Sequence button to activate a group camera sequence

A View button to show in Live mode the multiplexed output from the VCR and in VCR mode to show the multiplexed input from the VCR

A zoom button

A picture-in-picture button

Buttons for 4-, 9-, and 16-screen display

C2907M-D (4/05) 59

The following are arrayed down the right side of the page:

Radio buttons for 16 cameras

Iris open and close buttons

Focus far and near buttons

Zoom out and in buttons

Eight direction arrow buttons with a home button in the center to return the camera to its home position (preset 1)

Ten numbered buttons to use with the Pres and Pattern buttons to activate a preset and run patterns

A SET check box to use in programming presets and patterns

A Pattern button to run a pattern for each camera

In Control or No Control below the buttons indicates whether you have control of the camera. Recording control buttons are beneath the picture (live video page only).

On the Genex live control page, you can control the following:

Monitor: To select a monitor, click either the Main or Spot radio button.

Camera: To select a camera, click one of the 16 camera radio buttons.

Presets: To program a preset from the Genex browser page: set the image using the arrow keys, click SET, enter a preset number, and then click Pres. To activate a preset, enter the preset number and press Pres. (You must click the Clear button before activating another preset.)

Patterns: To program a pattern from the Genex browers page: click SET, click Pattern, run your pattern using the arrow keys, and then click Pattern again when you are nished. To run a pattern, click Pattern. (You can run only the rst programmed pattern.) To stop a pattern: click 96 and then click Pres.

Sequence: To activate a group camera sequence, click Sequence.

SPECTRA LIVE VIDEO/SERVER PUSH PAGE CONTENTS

Figure 45. Spectra Control Page (Live Video Page Shown)

The Spectra page contains the following at the top of the page:

Live video indicators (live video page only)

The following are arrayed down the right side under Lens:

Iris open and close buttons

Focus far and near buttons

Zoom out and in buttons

60 C2907M-D (4/05)

The following are arrayed under Pan/Tilt:

Eight direction arrow buttons

Home button in the center to return the camera to its home position (preset 1)

The following are arrayed under Presets:

Ten numbered preset buttons

Pres (preset) button

Clear button

A SET check box

The following are arrayed under Pattern:

A Start pattern button

A Stop pattern button

In Control or No Control indicates whether you have control of the camera. Recording control buttons are beneath the picture (live video page only).

On the Spectra live video control page, you can control the following:

Presets: To program a preset from the Spectra browser page: set the image using the arrow keys, click SET, enter a preset number, and then click Pres.To activate a preset: enter a preset number and click the Pres button.

Patterns: You can program and run only one pattern through PelcoNet. To program a pattern: click SET, click Start, run your pattern using the arrow keys, and then click Stop. To operate a pattern: click Start to begin the pattern and Stop to halt.

Programming menus: To access the programming menus: enter 95, click SET, and then Pres. Use the open iris icon to open menus and arrow keys to navigate and set options. Use the open iris icon in conjunction with the Exit option to move backward through menu layers and to exit programming mode.

NOTE: You can program presets and patterns for Spectra III either from inside the camera menu or through a controller. With Spectra II you can program presets and patterns through a controller or through the browser.

ESPRIT LIVE VIDEO/SERVER PUSH PAGE CONTENTS

Figure 46. Esprit Control Page (Live Video Page Shown)

C2907M-D (4/05) 61

The Esprit page contains the following at the top of the page:

Live video indicators (live video page only)

The following are arrayed down the right side under Lens:

Iris open and close buttons

Focus far and near buttons

Zoom out and in buttons

The following are arrayed under Pan/Tilt:

Eight direction arrow buttons

Home button in the center to return the camera to its home position (preset 1)

The following are arrayed under Presets:

Ten numbered preset buttons

Pres (preset) button

Clear button

A SET check box

The following are arrayed under Pattern:

A Start pattern button

A Stop pattern button

A Wiper button

In Control or No Control indicates whether you have control of the camera. Recording controls buttons are beneath the picture (live video page only).

On the Esprit live video control page, you can control the following:

Presets: To program a preset from the Esprit browser page: set the image using the arrow keys, click SET, enter a preset number, and then click Pres. To activate a preset: click a preset number button, and then click Pres. (You must click the Clear button before activating another preset.)

Patterns: You can program and run only one pattern through PelcoNet. To program a pattern: click SET, click Start, run your pattern using the arrow keys, and then click Stop. To operate a pattern: click Start to begin the pattern and Stop to halt.

Programming menus: To access the programming menus: enter 95 and click SET, and then Pres. Use the open iris icon to open menus and arrow keys to navigate and set options. Use the open iris icon in conjunction with the Exit option to move backward through menu layers and to exit programming mode.

62 C2907M-D (4/05)

KEYBOARD LIVE VIDEO/SERVER PUSH PAGE CONTENTS

Figure 47. Keyboard Control Page (Live Video Page Shown)

The Keyboard page lets you control a camera through a Pelco keyboard rather than through a PCs keyboard. The Keyboard page contains live video indicators (live video page only) at the top of the page. Recording control buttons are beneath the picture (live video page only). The hard disk icon (when showing) indicates that a compact ash drive is connected.

RECORDING AND VIEWING THE DISPLAY ON A PC AND THE NET350 Video 1 and 2 and live video control pages let you keep snapshots (still pictures) and record the camera video display on a PCs hard drive and play it back later. (You can also record snapshots from the Server Push pages.) The le is recorded on the hard drive of the PC on which you are viewing the picture. The controls are a row of buttons beneath the screen.

NOTE: When video les are saved, an extra le (.ind extension) is created that lets you see the video in Pelcos MPEG Viewer. If you delete this le, you cannot view the saved .mp4 le.

CHOOSING WHERE TO STORE THE FILE

The program automatically saves snapshots and video recording les at C:\ on the hard drive of the PC on which you are viewing the picture unless you tell it otherwise. If you want to store les in a different location on the PC, you need to rst specify that location. To do so:

1. On the Home page, click either Control (and then click one of the underlined links to a live video control page) or Video 1 or Video 2.

2. Click the Select path icon (open folder) beneath the picture. (Click the icon just once. Double-clicking may cause display problems with the select path window.)

3. The program opens the Path for saving MPEG/JPEG les screen. Do not specify a le name (leave blank), just navigate to the location where you want the le stored and then click the Save button.

The le of any snapshot or video you record will be saved to that location.

C2907M-D (4/05) 63

RECORDING A SNAPSHOT FROM VIDEO

You can record a snapshot from the Video 1 or 2 pages or from the live video and Server Push, Matrix, Genex, Spectra, and Esprit control pages. The le is recorded on the PC on which you are viewing the picture. To do so:

1. On the Home page, click either Control (and then click one of the underlined links to a live video control page) or Video 1 or Video 2 or Server Push.

2. Position the camera as desired (if it has PTZ capability).

3. Click the Snapshot icon (camera) to record a still picture. The snapshot is saved on the PCs hard drive with a .jpg extension.

VIEWING A SNAPSHOT

You can view a snapshot by double-clicking the desired le (.jpg extension) in Windows Explorer.

RECORDING THE VIDEO DISPLAY ONTO THE PC

You can record the camera display from the Video 1 or 2 pages or from the live video Matrix, Genex, Spectra, and Esprit control pages. The le is recorded on the PC on which you are viewing the picture. To do so:

1. On the Home page, click either Control (and then click one of the underline links to a live video control page) or Video 1 or Video 2.

2. Position the camera as desired (if it has PTZ capability).

3. Click the Recording icon (red dot button) to begin recording. The button ashes while recording is happening.

4. Click the Recording button again to stop recording. The recording is saved on the PCs hard drive with an .mp4 extension.

RECORDING THE VIDEO DISPLAY THROUGH COMPACTFLASH

Instead of recording video sequences onto your computers hard drive, you can choose to record them locally onto the NET350. For local recording through the CompactFlash interface on the NET350s front panel, you can use standard CompactFlash cards or miniature disk drives with a capacity of up to one GB. Video sequences are recorded in MPEG format.

NOTE: Remember, once you click the Start button to activate time or alarm scheduling, you cannot make changes or view other partitions until you stop the scheduler with the Stop button.

To record onto the NET350, you must rst set up the unit for recording. To do so:

1. Click Media Recording on the Setup screen.

2. Storage can be allocated to more than one partition. If desired, click the Enter partition settings! button to access a screen that shows information about existing partitions. You can also delete partitions or access a wizard to guide you through adding partitions. When you nish, click the Back to HD Scheduler page! button.

3. If desired, click the Properties tab to access a screen where you can designate what properties you want associated with a partition. Refer to the Conguration Pages for Media Recording and Conguration Page for Properties sections. Click Set when nished.

4. If desired, click the Time recording tab to access a screen where you can set the times you want recording to occur. Refer to the Conguration Pages for Media Recording and Conguration Page for Time Recording sections.

Clicking a day button selects the entire row; clicking a time button selects an entire column. Clicking Select all picks all days and times. Or select a specific day and time by holding and dragging the mouse button.

Deselect by right clicking the mouse button on the selection. Deselect all with the Clear button.

Click Set, and then Start when finished.

5. If desired, click the Alarm recording tab to access a screen where you can set the times you want alarm recording to be active. Refer to the Conguration Pages for Media Recording and Conguration Page for Alarm Recording sections.

Selection and deselection work just as on the Time Recording screen described above. Click Set, and then Start when nished.

64 C2907M-D (4/05)

VIEWING THE VIDEO DISPLAY

The video le is identied by date and time. View the video display using the MPEGViewer program included on the PelcoNet Resource CD. Do the following:

1. Locate the MPEGViewer.exe le (either on the resource CD or the PC) or MPEG Viewer shortcut on the desktop if you used the installation program on the CD. Double-click the le. The viewer opens.

Figure 48. Viewer Screen

2. Click the Open button. A browse dialog box opens. Navigate to the recorded le (.mp4 extension) you want to view. Click the le to highlight it, and then click Open.

3. Click Play on the viewer to begin playback. The start and end locations are shown below the slide control. A counter marks your location in the le.

4. Use the Pause button to temporarily halt playback. You can change your location in the le by moving the pointer on the slide control. Click Play to resume playback.

5. Click Stop to halt playback.

NOTE: When video les are saved, an extra le (.ind extension) is created that lets you see the video in Pelcos MPEG Viewer. If you delete this le, you cannot view the saved .mp4 le.

C2907M-D (4/05) 65

MEDIA PLAYBACK SCREEN Use this screen to view les recorded onto the units CompactFlash card, to record a snapshot, or to back up the recorded le onto your computers hard drive.

Figure 49. Media Playback Screen

VIEWING A FILE

To view a le:

1. Click Media Replay on the home page, live video page, server push page, or any control page. The Media Playback screen appears.

2. Use the pull-down menu to choose the partition from which you want to view a le. A list of les in the partition will be displayed. For each le you will see the order of recording, start/stop times, duration, and the number and type of alarms recorded.

3. Click the desired le. Playback begins in the viewing window automatically. You control the playback as follows:

a. Below the window is a blue date/time video bar divided into increments. You can change the graduation by clicking the zoom in and zoom out magnifying glass icons. Select between intervals of three days, one day, two hours, ve minutes, or one minute.

The indicator below the lavender bar shows the date and exact time.

A yellow slider shows your position in the displayed le. (You may have to click in the lavender bar to display the yellow slider.) Use the left and right arrow buttons on the blue bar to select the time in the le you want to see. Or you can move the blue bar left or right with the mouse button held down.

b. You can pick another le for playback by clicking the corresponding time mark in the blue bar. The green border in the lavender bar signies the active le. You can also start playback by positioning the mouse on the yellow slider, and then holding down the mouse button while moving the slider to the time you want.

c. Use the arrow buttons on the scale at the bottom of the screen to control the playback speed (100% is regular speed; lower values are slower while higher values are faster).

d. Red strips on the video bar indicate alarm activation.

4. Use the following buttons to further control playback:

These buttons jump the display to the next track or to the previous track.

This button plays the recording.

This button stops the playback.

66 C2907M-D (4/05)

These buttons move the display backward and forward while the display is paused.

This button pauses the playback.

BACKING UP A FILE ONTO A COMPUTER

You can also save video recordings that are on the NET350 directly to your computers hard drive as backup. To do so:

1. Start playing back the le you want to back up in whole or in parts (refer to the Viewing a File section).

2. Click the red circle icon to immediately start recording onto the PCs hard drive. The circle blinks slowly to indicate recording has started.

3. Click the red circle icon again to stop recording.

You can repeat this procedure several times within a le to back up sections out of a long le.

RECORDING A SNAPSHOT FROM A FILE

You can record onto your computers hard drive an individual frame (snapshot) from a le being played back. Do the following

1. Start playing back the le from which you want to take a snapshot (refer to the Viewing a File section).

2. Click the camera icon to store a snapshot. Snapshots are immediately displayed in the window on the right.

3. If a snapshot does not appear, go to the live page, click the select path icon, and then enter a new path where the snapshot will be saved. Repeat steps 1 and 2.

C2907M-D (4/05) 67

Software Upload Units have ash EPROMs for software upgrades in the eld. These upgrades can be done directly from the web browser. To do so:

1. Obtain the latest PelcoNet NET350 transmission system software from Pelco (http://www.pelco.com).

2. Use the browser to select the General Settings conguration page of your unit.

3. Use the Browse button in the Software upload eld to select the correct new rmware le.

4. Click the Upload button. The Upload progress eld shows how the upload is proceeding.

After about 30 seconds you should get a feedback message from the connected unit. The message Upload Complete WAIT conrms the correct upload of the new rmware, which is now being installed. If you try to upload an invalid rmware le, you will get the message Upload Failed.

The unit automatically restarts when a successful upload is completed.

However, if the LED ashes green/red alternately on conclusion, the upload has been unsuccessful and must be restarted. To do so: in the browsers address eld after the units IP address, enter /main.htm. For example, 192.168.0.12/main.htm. Restart the upload process.

5. If you revisit the General Settings conguration page after the rmware is uploaded successfully, you will see the message New Firmware Installed.

Resetting the NET350 Hard reset: Use a strong, thin item like a piece of wire to press the hard reset button on the front panel (refer to Figure 1) for three

seconds. The unit will then reset.

Soft reset: Type a forward slash (/) and reset at the end of the units address in the Internet Explorer browser address window, and then press Enter. The unit then displays the message Bye Bye Going to reset.

WARNING: Do not disconnect power to the unit for any reason while rmware is being installed. Disrupting the cycle will damage the ash EPROM. If this occurs, you will have to return the unit for repair.

68 C2907M-D (4/05)

Troubleshooting If the following instructions fail to solve your problem, contact Pelco Technical Support at 1-800-289-9100 for help. You should have the serial number from the bottom of the unit and the rmware version ready in case they are needed.

Do not try to repair a unit yourself. Opening it immediately voids any warranty. Leave maintenance and repairs to qualied technical personnel. Swap a defective unit with a replacement unit and return the defective one for repair.

LEDS The NET350 has several LEDs that indicate the operating status and possible faults.

TERMINAL PROGRAM If the terminal program fails to connect to the units terminal port, check the following:

Is the right COM port interface on the PC selected for the terminal program, and are the settings correct? Isthe cable connected to COM 1 and not COM 2 on the PelcoNet unit? Program default settings are 19200kb/s, 8 data bits, no parity, 1 stop bit (8N1) for the terminal program.

If the data exchange between the terminal program and the system still does not work, check the serial cable. Does the system answer when you press Enter on your keyboard?

Disable the local echo if you see duplicate characters on your screen.

TROUBLESHOOTING A TCP/IP NETWORK USING A PING UTILITY (Enter the appropriate information where indicated by the quotation marks. Do not enter the quotation marks.)

To see if a unit in your network can be reached, try to ping your unit by typing the following command in a DOS window:

c:\ping unit IP address

If it is reached, there will be a response like the following:

Reply from : bytes=32 time=NN ms TTL=xxx

If the LAN is malfunctioning, the ping command will time out. If so, you could have one of the following problems:

Wrong physical connections. Make sure the LAN link LED is on.

Wrong network connection. Verify the IP address is entered correctly and that subnet mask and gateway address are set properly.

Otherwise, ask your network administrator.

Table D. LED Denitions

LED Indication Meaning Power Not lit Device is switched off.

Lit green Device is switched on.

Flashing green Device is transmitting/receiving video/audio

Lit red (temporary) Device is starting.

Lit red (permanent) Device is out of order.

Flashing green/red Upload failed.

I Lit red Alarm input is activated.

Not lit Alarm input is inactive.

O Lit green Relay is switched.

Not lit Relay is inactive (resting state)

L Lit green Physical connection to the network is established.

Not lit There is no network connection.

T Flashing yellow Data is being transmitted via the network.

Not lit There is no data transmission.

C2907M-D (4/05) 69

TROUBLESHOOTING CONNECTION PROBLEMS If you fail to connect to a system from a NET350 receiver, check the following to pinpoint the problem:

Do not connect two units of the same type (for example, receiver to receiver).

Make sure network connectivity is available (for example, by using the ping command as described previously).

Does the power LED ash?

If ashing, the units are connected. Verify how much bandwidth your connection has available and ensure the bandwidth specied in the Datarate eld on the MPEG-4 Video Settings page does not exceed the available bandwidth.

If the power LED does not ash, verify that the Live Video Auto-Connect feature is set up correctly. Also, set the Video/Audio Transmission eld on the Network Settings page to TCP (port 80).

TROUBLESHOOTING THE VIDEO CONNECTION If no video or a distorted video image is displayed at the receiver during a connection to a transmitter:

Make sure to use the right unit for your application: a camera can only be connected to a transmitter, never to a receiver.

Make sure the video input on the transmitter is properly terminated.

Make sure the camera is switched on and the coaxial cable is connected to the transmitter.

Check the camera cable and connect a video monitor to the camera to check that the camera is functioning correctly.

Make sure the monitor is switched on and the coaxial cable is connected to the NET350R receiver.

Check the monitor cable and the selection of the monitor channel if the monitor features more than one video channel.

(NET350R unit only.) Make sure the Output Standard eld on the Video Decoder Settings page is set for the TV signal used in your region (NTSC or PAL). Restart the receiver if you have to change this eld.

70 C2907M-D (4/05)

Specications NETWORK PROTOCOL AND STANDARDS COMPATIBILITY Network Protocols RTP, RTCP, UDP, TCP, IP, HTTP, SNMP, IGMP, ICMP, ARP Video Coding MPEG-4 (MJPEG in Server Push only) Video Frame Rate Up to 30 images/second

INTERFACE Video Input or Output 1, BNC, PAL/NTSC, 75 ohms, 1 Vp-p Audio Input/Output 3.5 mm stereo jack ring/tip contact LAN Interface Ethernet 10/100BASE-T autosensing, RJ-45 LAN Data Rate 9.6 Kbps to 5.0 Mbps Data Interfaces 1 RS-232/RS-422/RS-485, bidirectional (9-pin, D-sub) and 1 RS-232 (9-pin, D-sub) Alarm Input 1 terminal, 30 VDC maximum Alarm Output 1 terminal, 30 VDC, 1 A

VIDEO Video Standards PAL, NTSC Video Image Size

PAL 4 CIF 704 x 576 pixels 2 CIF 704 x 288 pixels CIF 352 x 288 pixels

NTSC 4 SIF 704 x 480 pixels 2 SIF 704 x 240 pixels SIF 352 x 240 pixels

AUDIO Output

Physical Connection 3.5 mm stereo jack tip contact Maximum Output Voltage 2.5 Vp-p Maximum Output Power RMS 60 mW Output Impedance 8, 16, 32 ohms

Input Physical Connection 3.5 mm stereo jack ring contact Input Voltage 1 Vp-p (line level) Input Impedance 50 kohm Input Frequency Range 300 Hz - 10 kHz Audio Distortion <1% Audio Signal-to-Noise Ratio >50 dB (maximum)

POWER Type Plug power adapter Operating Voltage 12-24 VDC, power supply included Power Consumption Approximately 10 W

MISCELLANEOUS LED Displays 5 LEDs (alarm, relay, connection, data, power)

ENVIRONMENTAL Operating Temperature 32 to 122F (0 to 50C) Operating Humidity 80% maximum relative humidity, noncondensing Storage Temperature -4 to 140F (-20 to 60C) Storage Humidity 95% maximum relative humidity, noncondensing

GENERAL Dimensions 5.6 (W) x 1.3 (H) x 5.3 (D) inches (14.3 x 3.3 x 13.5 cm) Unit Weight Approximately 0.9 lb (0.4 kg) without power supply

C2907M-D (4/05) 71

Glossary 10BASE-T IEEE 802.3 specication for 10 Mbs Ethernet

ARP Address Resolution Protocol

Baud Rate Data transmission rate

bps Bits per second, the actual data rate

Cat5 Cable Type of cable used on a LAN to connect computers, printers, and transmitters and receivers to a hub on the network

CIF Common Intermediate Format; video format with 352 x 288 pixels

Default Gateway The routers IP address (for example, 192.168.0.1)

DHCP Dynamic Host Conguration Protocol

DNS Domain Name Service

FTP File Transfer Protocol

Full Duplex Simultaneous data transmission in both directions

G.711, G.728 Standard audio coding algorithms dened by ITU-T

H.224 Standardized protocol for data communication and remote control

H.261 Standard motion video coding algorithm dened by ITU-T

H.323 Standard for M-JPEG video and audio compression dened by ITU-T

HTML Hypertext Markup Language

HTTP Hypertext Transfer Protocol

Hub A device on the network that connects multiple computers together to form a LAN

ICMP Internet Control Message Protocol

ID Identication: machine readable number or name

IGMP Internet Group Management Protocol

IEEE Institute of Electrical and Electronics Engineers

Internet Protocol The main protocol used on the Internet. Formsin conjunction with the Transfer Control Protocol (TCP)the TCP/IP protocol suite.

IP See Internet Protocol

IP Address A unique four-byte number that identies each unit on the Internet or network. Usually written in dotted decimal notation with periods separating the bytes. This address is required to communicate on the network (for example, 192.168.0.100)

ISDN Integrated Services Digital Network

ISP Internet Service Provider

JPEG Joint Photographic Expert Group (procedure to encode still images)

Kbps Kilobits per second; the actual data rate

LAN Local Area Network. Multiple computers linked together into a network to share information within a limited geographic area (such as a building or a campus) controlled by a network operating system and using a transport protocol.

MAC Address Media Access Control/hardware address

72 C2907M-D (4/05)

Mbps Megabits per second; the actual data rate

MPEG-4 Used for transmission of audiovisual data with very low transfer rates (for example, via Internet); further development of MPEG-2 (enhanced video compression standard)

NAT Network Address Translator. A proposal for IP address for re-use where the local IP address is mapped to a globally unique address

Network address Translator A proposal for IP address re-use where the local IP address is mapped to a globally unique address

Parameter Values used for the conguration of the network system

Picture A video picture that has been digitized at a particular resolution

PPP Point-To-Point Protocol. A protocol allowing a computer using TCP/IP to connect directly to the Internet

Router A physical device that connects multiple LANs; a router knows where to direct a given packet of data

QCIF Quarter CIF, video format with 176 x 144 pixels

Server Push A continuous stream sent from the transmitter to the web browser

Subnet Mask A mask that explains which part of an IP address is the network address and which part composes the hose address; it is usually expressed in dotted-decimal notation (for example, 255.255.255.192)

TCP Transfer Control Protocol

UDP User Datagram Protocol

URL Uniform Resource Locator

UTP Unshielded Twisted Pair

WAN Wide Area Network. Multiple LANs connected together, usually over a great distance.

C2907M-D (4/05) 73

Appendix A Connecting PelcoNet to Various Components Some of the connection examples that follow require a DB9 cable. Refer to the following gure when one is needed.

Figure 50. DB9 Cable Wire Splicing

SPECTRA

ESPRIT

TX+ TX-

RX+ RX-

TX+ TX-

RX+ RX-

DB9 TO RECEIVER

1 2 3 4 5 6 7 8 9

PIN

DCD (DATA CARRIER DETECT) RX (RECEIVE DATA) TX (TRANSMIT DATA) DTR (DATA TERMINAL READY) GND (GROUND) DSR (DATA SET READY) RTS (READY TO SEND) CTS (CLEAR TO SEND)

RX+ (RECEIVE DATA PLUS) TX- (TRANSMIT DATA MINUS)

GND

TX+ (TRANSMIT DATA PLUS) RX- (RECEIVE DATA MINUS)

RS-232 RS-422/RS-485

1 2 3 4 5

6 7 8 9

74 C2907M-D (4/05)

CONNECTING PELCONET TO VARIOUS COMPONENTS WITH ASSORTED KEYBOARDS

CONNECTION SCENARIO 1 USING A KBD300A IN DIRECT MODE

Refer to Figure 51 and the instructions that follow.

Figure 51. KBD300A (Direct Mode) Connected to a Receiver or Spectra Dome System

1. Connect a DB9 cable to the COM1 port on the back of the NET350 receiver. (In the Interface Mode eld on the conguration page for the COM1 interface settings, select RS422/485.) The data format should be 4800 baud, 8 data bits, no parity, and 1 stop bit.

2. Connect RX- on the DB9 cable to terminal 2 on the wall block. Connect RX+ on the DB9 cable to terminal 1 on the wall block.

3. Connect a 12 VAC power supply to terminals 3 and 4 on the wall block.

4. Set DIP switch 6 on the KBD300A to ON to enable turbo pan operation or OFF to disable that feature. The KBD300A will recognize Direct Mode automatically.

5. Connect the wall block to the KBD300A with an RJ-45 straight cable.

6. Connect the monitor.

7. Refer to Figure 50 and Figure 51. Splice the supplied DB9 cable into the Spectra/Esprit or receiver cable. Use P protocol only.

8. Plug the DB9 cable into the COM1 port on the transmitter. (In the Interface Mode eld, select RS-422/485.) The data format should be 4800, 8, no parity, 1.

9. Connect the cameras video to the transmitter.

TX-

TX+

P PROTOCOL ONLY

RECEIVER OR SPECTRA

RX+ RX-

TRANSMITTER

Video In

75 Audio I/O

COM2 RS232

COM1 RS232/422/485

Power

Video Out

75 Audio I/O

Power

RX-

RX+

12 VAC

KBD300A

STRAIGHT CABLE

DIRECT MODE

RECEIVER

1 2 3 4

8 7 6 5

4800, 8, NONE, 1

COM2: RS232

COM1: RS232/422/485

4800, 8, NONE, 1

C2907M-D (4/05) 75

CONNECTION SCENARIO 2 USING A KBD4000 FOR MULTIPLEXER CONTROL

Refer to Figure 52 and the instructions that follow.

NOTE: If you set all your cameras to Standard Coaxitron for better control on the browser, you will lose most of the KBD4000 keyboard control functions. If you set your cameras to Extended Coaxitron, you will have all the keyboard functions but the PTZ functions on the NET350 will be very slow.

Figure 52. KBD4000 Connected to a Multiplexer

1. Connect a DB9 cable to the COM1 port on the back of the NET350 receiver. (In the Interface Mode eld on the conguration page for the COM1 interface settings, select 232.) The data format should be 9600 baud, 8 data bits, odd parity, and 1 stop bit.

2. On the receiver side, connect TX- on the DB9 cable to terminal 7 on the wall block. Connect TX+ on the DB9 cable to terminal 8 on the wall block. Connect RX- on the DB9 cable to terminal 2 on the wall block. Connect RX+ on the DB9 cable to terminal 1 on the wall block.

3. Connect a 12 VAC power supply to terminals 3 and 4 on the wall block.

4. Connect the wall block to the KBD4000 with an RJ-45 straight cable. (Note that DIP switches 4 and 8 on the KBD4000 must be set ON.)

5. Connect the monitor.

6. Refer to Figure 50 and Figure 52. Splice the supplied DB9 cable into the multiplexer wall block. Connect TX- from the NET350 transmitter to terminal 2 on the wall block, TX+ to terminal 1, RX- to terminal 7, and RX+ to terminal 8.

7. Plug the DB9 cable into the COM1 port on the transmitter. (In the Interface Mode eld, select RS-422/485.) The data format must be 9600, 8, odd, 1.

8. Connect the wall block to COM IN on the multiplexer with an RJ-45 straight cable.

9. Connect MAIN video output from the multiplexer to the transmitter.

1 2 3 4

8 7 6 5

TRANSMITTER

Video In

75 Audio I/O

COM2: RS232

COM1: RS232/422/485

Power

Video Out

75 Audio I/O

Power

RECEIVER

STRAIGHT CABLE

MULTIPLEXER

COM IN

TX- TX+ RX- RX+

9600, 8, ODD, 1

COM2: RS232

COM1: RS232/422/485

12 VAC

KBD4000

STRAIGHT CABLE

DIRECT MODE

1 2 3 4

8 7 6 5

RX- RX+ TX- TX+

9600, 8, ODD, 1

76 C2907M-D (4/05)

CONNECTION SCENARIO 3 USING A CM9760-KBD

Refer to Figure 53 and the instructions that follow.

Figure 53. CM9760-KBD Connected to a CM9700-CC1 Controller

1. Connect a DB9 cable to the COM1 port on the back of the NET350 receiver. (In the Interface Mode eld on the conguration page for the COM1 interface settings, select RS-232.) The data format must be 4800baud, 8 data bits, even parity, and 1 stop bit.

2. On the receiver side, connect TX- on the DB9 cable to terminal 7 on the wall block. Connect TX+ on the DB9 cable to terminal 8 on the wall block. Connect RX- on the DB9 cable to terminal 2 on the wall block. Connect RX+ on the DB9 cable to terminal 1 on the wall block.

3. Connect an RJ-45 straight cable from the wall block to the power pack.

4. Connect an RJ-45 straight cable from the keyboard input connector on the power pack to COM 1 on the keyboard.

5. Connect the monitor.

6. Refer to Figure 50 and Figure 53. Splice the supplied DB9 cable into the CM9760-CC1 wall block. Connect TX- from the NET350 transmitter to terminal 2 on the wall block, TX+ to terminal 1, RX- to terminal 7, and RX+ to terminal 8.

7. Plug the DB9 cable into the COM1 port on the transmitter. (In the Interface Mode eld, select RS-232.) The data format must 4800, 8, even, 1.

8. Connect an RJ-45 ipped cable from the wall block to Sercom port 5 on the CC1s rear panel.

RECEIVER

Video In

75

Audio I/O

COM2:

RS232

COM1:

RS232/422/485

Power

12 VDC

4800, 8, EVEN, 1

FLIPPED CABLE

TRANSMITTER

PV130 1

2

3

4

8

7

6

5

TX(-) TX(+)

RX(-)

RX(+)

SERCOM PORT PROGRAMMED FOR KBD

CM9700-CC1

Video Out

75

Audio I/O

Power

12 VDC

RX(-)

RX(+)

4800, 8, EVEN, 1

STRAIGHT CABLE

DIRECT MODE

PV130

1

2

3

4

8

7

6

5

TX(-) TX(+)

CM9760-KBD

CM9505UPS

COM2:

RS232

COM1:

RS232/422/485

C2907M-D (4/05) 77

9. Connect one of the three monitor outputs on the rear of the controller to the transmitter.

CONNECTING A LOCAL KEYBOARD TO A PC Refer to Figure 54. This conguration lets an operator control a camera or other external device through a Pelco keyboard attached to a local PC. (The KBD200A is shown as an example.)

Figure 54. Connecting a Local Keyboard to a PC

CONNECTING PELCONET COM 1 RS-232 PORT TO THE GENEX MULTIPLEXER COM OUT PORT Refer to Figure 55 and the instructions that follow.

Figure 55. Connecting PelcoNet to Genex Using the COM 1 RS-232 Port

1. Verify that the multiplexer has Version 4.1 or higher software for Genex units manufactured before November 22, 2002or Version 1.12 or higher for units manufactured on or after that date. (The version numbering was restarted in 2003, which is why newer units have a smaller version number. The version number ashes on the monitor when power is applied to the multiplexer.)

2. Set the NET350 COM1 data port to Transparent, 9600 baud, 8 data bits, none (for parity), 1 stop bit, and off if it is not so set already. (In the Interface Mode eld on the conguration page for the COM1 interface settings, select RS-232.)

PV140

1 2 3 4

8 7 6 5

12 VAC

KBD200A/ KBD300A

RX-

RX+

STRAIGHT CABLE

75 Audio I/O

Powe r

NET350 TRANSMITTER

ETHERNET CONNECTION TO NETWORK (LAN/WAN)

1 3 5 7 9

2 4 6 8 10

11

12 14

13 15

16

1

2

VIDEO INPUTS VIDEO OUTPUTS

ALARM S (1-9 )

ALARM S (10-18)

COM 1 ( 1-6) COM 2 ( 7-12)

CONTROL OUTPUTS

REMOTE KEYBOARD(S)

LOCAL KEYBOARD

1 2 3 4 5 6 7 8 9

10 11 12 13 14 15 16 17 18

1 2 3 4 5 6 7 8 9 10 11 12

0 1 2 3 F 2

F 3

N O

N C

C O M

T T R R + +

COM2 : RS232

COM1 : RS232/422/485

Vi deo In

PC WORKSTATION

PELCO KEYBOARD

TX -

TX +

RX -

RX +

GN D

12 V

12VDC

TRANSMITTER

Video In

75 Audio I/O

COM2: RS232

Power

ETHERNET CONNECTION TO NETWORK

PELCONET DB9 CONNECTOR

GENEX COM OUT RJ-45 CONNECTOR

PIN 2 PIN 3 PIN 5

RX TX

GND

PIN 6 PIN 4 PIN 5

TX RX

GND

18 18

GENEX COM

IN OUT

9600, 8, ODD, 1

MULTIPLEXER

COM1: RS232/422/485

78 C2907M-D (4/05)

3. Create a cable using the diagram in Figure 50.

4. Attach the cables DB9 connector end to PelcoNets COM1 port. Connect the cables RJ-45 connector end to COM out on the back of the multiplexer.

5. Connect the MAIN video output from the multiplexer to the NET350 transmitter.

6. Connect PelcoNets Ethernet port to the network using a Cat5 Ethernet patch cable.

CONNECTING PELCONET TO A CM6700 AND KBD200A FOR REMOTE ASCII CONTROL Refer to Figure 56. This conguration lets an operator view and control cameras with a remote KBD200A keyboard.

Figure 56. Using PelcoNet with CM6700 and KBD200A to Provide Remote Control

Video In

75 Audio I/O

Power

TRANSMITTER

ETHERNET CONNECTION TO NETWORK (LAN/WAN)

NOTE: FIRMWARE VER 4.0 OR LATER REQUIRED. SET KEYBOARD DIP SWITCHES SWITCH 6 ON, SWITCHES 5 AND 8 OFF, SWITCHES 1-4 FOR ADDRESS ACCORDING TO THE TABLE IN THE KBD200A MANUAL.

1 3 5 7 9

2 4 6 8 10

11

12 14

13 15

16

1

2

VIDEO INPUTS VIDEO OUTPUTS

ALARMS (1-9)

ALARMS (10-18)

COM 1 (1-6) COM 2 (7-12)

CONTROL OUTPUTS

REMOTE KEYBOARD(S)

LOCAL KEYBOARD

1 2 3 4 5 6 7 8 9

10 11 1213 14 15 16 1718

1 2 3 4 5 6 7 8 9 10 11 12

0 1 2 3 F 2

F 3 N O N C C O M

T T R R + +

1 2 3 4 5 6 7 8

ON

1 2 3 4 5 6 7 8

ON RS-422/485

ON OFF

KEY

RS-232

SW5 DIP SWITCH SETTINGS

SET DIP SWITCH (SW5) ON CM6700-MXB TO RS-232 MODE

CM6700 MATRIX COM 2 PORT SETTINGS:

BAUD RATE DATA BITS PARITY STOP BITS

9600 8 ODD 1

CONNECT PELCONET TO 6700 VIA RS-232 PORT

Video Out

75 Audio I/O

Power

RECEIVER

ETHERNET CONNECTION TO NETWORK (LAN/WAN)

TX+RX-

12 VAC

KBD200A

STRAIGHT CABLE

1 2 3 4

8 7 6 5

RX+ TX-

SPECTRA COAXITRON PROTOCOL

2-RX 3-TX G-GND

PELCONET REMOTE KBD200A ASCII MODE SETUP

COM2: RS232

COM1: RS232/422/485

PELCONET TRANSPARENT

DATA PORT

2 RX............................ 3 TX........................... 5 GND.....................

CM6700-MXB COM 2 (7-12)

7 TX 12 RX

9 GND

COM2: RS232

COM1: RS232/422/485

TRANSPARENT DATA PORT USING INTERNET EXPLORER, SET TRANSPARENT DATA SETTINGS ON BOTH PELCONET RECEIVER AND TRANSMITTER:

BAUD RATE DATA BITS PARITY STOP BITS

9600 8 ODD 1

C2907M-D (4/05) 79

CONNECTING PELCONET TO A CM6700 ASCII PORT

Refer to Figure 57. This conguration lets an operator view and control cameras from a PC using a web browser. (The operators PC is not shown on the diagram.)

Figure 57. Using PelcoNet with CM6700 to Provide Remote Control

Video In

75 Audio I/O

Power

TRANSMITTER

ETHERNET CONNECTION TO NETWORK (LAN/WAN)

1 3 5 7 9

2 4 6 8 10

11

12 14

13 15

16

1

2

VIDEO INPUTS VIDEO OUTPUTS

ALARMS (1-9)

ALARMS (10-18)

COM 1 (1-6) COM 2 (7-12)

CONTROL OUTPUTS

REMOTE KEYBOARD(S)

LOCAL KEYBOARD

1 2 3 4 5 6 7 8 9

10 11 1213 14 15 16 1718

1 2 3 4 5 6 7 8 9 10 11 12

0 1 2 3 F 2

F 3 N O N C C O M

T T R R + +

1 2 3 4 5 6 7 8

ON

1 2 3 4 5 6 7 8

ON RS-422/485

ON OFF

KEY

RS-232

SW5 DIP SWITCH SETTINGS

SET DIP SWITCH (SW5) ON CM6700-MXB TO RS-232 MODE

CM6700 MATRIX COM 2 PORT SETTINGS:

BAUD RATE DATA BITS PARITY STOP BITS

9600 8 ODD 1

TRANSPARENT DATA PORT USING INTERNET EXPLORER, SET TRANSPARENT DATA SETTINGS ON BOTH PELCONET RECEIVER AND TRANSMITTER:

BAUD RATE DATA BITS PARITY STOP BITS

9600 8 ODD 1

2-RX 3-TX G-GND

PELCONET TRANSPARENT

DATA PORT

2 RX............................ 3 TX............................ 5 GND.....................

CM6700-MXB COM 2 (7-12)

7 TX 12 RX

9 GND

PELCONET CM6700 ASCII SETUP SPECTRA COAXITRON PROTOCOL

COM2: RS232

COM1: RS232/422/485

80 C2907M-D (4/05)

CONNECTING PELCONET TO A CM9760-DT FOR REMOTE BROWSER CONTROL Refer to Figure 58. This conguration lets an operator view and control cameras on a PC using a web browser. (The operators PC is not shown on the diagram.)

Figure 58. Using PelcoNet with CM9760-DT to Provide Remote Control of a 9760 Monitor Output

Vi deo In

75 Audio I/O

Powe r

MON OUTPUT TIE LINE

CM9505-UPS

CM9760-KBD

ETHERNET CONNECTION TO NETWORK (LAN/WAN)

CM9760-CC1

CM9760-MXB

SPECTRA "P" PROTOCOL

SUPPLIED CABLE

TRANSMITTER

TRANSPARENT DATA PORT USING INTERNET EXPLORER SET TRANSPORT SETTINGS:

BAUD RATE DATA BITS PARITY STOP BITS

4800 OR 9600 8 EVEN OR ODD 1

CM9760-DT

2-RX 3-TX 5-GND

2-RX 3-TX 5-GND

1 ON 2 OFF DIP SWITCH

NULL MODEM CABLE NOT SUPPLIED

COM 2 PROGRAMMED FOR CM9760-DT COM 1 COM 2

NOTE: 4800 BAUD AND EVEN PARITY APPLIES TO CM9760-DT VERSION 2.07, WHILE 9600 BAUD AND ODD PARITY APPLIES TO VERSION 3.0

PELCONET CM9760-DT SETUP

COM2 : RS232

COM1 : RS232/422/485

C2907M-D (4/05) 81

CONNECTING PELCONET TO CM9700 FOR REMOTE COMMUNICATION Refer to Figure 50 and Figure 59 and Figure 60. These congurations let an operator remotely view and control cameras connected to the CM9700.

Figure 59. Using PelcoNet to Transmit Data and Video Between 9700 Nodes (9760 Shown)

SERCOM PORT PROGRAMMED FOR NETWORK COMMUNICATION (STRAIGHT CABLE)

Video In

75

Audio I/O

Power

MON OUTPUT TIE LINE

CM9505UPSCM9760-KBD

ETHERNET CONNECTION TO NETWORK (LAN/WAN)

CM9700-CC1

CM9760-MXB

SPECTRA P PROTOCOL

TRANSMITTER

BAUD RATE DATA BITS PARITY STOP BITS

9600 8 EVEN 1

1

2

3

4

8

7

6

5

RJ-45 WALL BLOCK NOT SUPPLIED

VIDEO

REMOTE NODE: TRANSMITTING DATA AND VIDEO

TRANSPARENT DATA PORT USING INTERNET EXPLORER SET TRANSPARENT DATA PORT SETTINGS:

COM2:

RS232

COM1:

RS232/422/485

* *WALL BLOCK CONNECTIONS

TERMINAL SERCOM PORT PELCONET

1 2 7 8

TX+ TX- RX- RX+

RX+ RX- TX- TX+

*

**

82 C2907M-D (4/05)

Figure 60. Using PelcoNet to Receive Data and Video Between 9700 Nodes (9760 Shown)

Video Out

75

Audio I/O

Power

CAM INPUT TIE LINE

CM9505UPS CM9760-KBD

ETHERNET CONNECTION TO NETWORK (LAN/WAN)

CM9700-CC1

CM9760-MXB

SPECTRA P PROTOCOL

RECEIVER

BAUD RATE DATA BITS PARITY STOP BITS

9600 8 EVEN 1

1

2

3

4

8

7

6

5

RJ-45 WALL BLOCK NOT SUPPLIED

VIDEO

CM9700-NW1

LOCAL NODE: RECEIVING DATA AND VIDEO

TRANSPARENT DATA PORT USING INTERNET EXPLORER SET TRANSPARENT DATA PORT SETTINGS:

COM2:

RS232

COM1:

RS232/422/485

* *WALL BLOCK CONNECTIONS

TERMINAL SERCOM PORT PELCONET

1 2 7 8

TX+ TX- RX- RX+

RX+ RX- TX- TX+

*

**

SERCOM PORT PROGRAMMED FOR NETWORK COMMUNICATION (STRAIGHT CABLE)

C2907M-D (4/05) 83

CONNECTING A PELCONET TRANSMITTER TO THE CM6800 ASCII PORT Refer to the transmitter portion of Figure 63. This conguration lets an operator view and control cameras with a PC using a web browser. (The operators PC is not shown on the diagram.) All settings are done in the CM6800 manager program or through a CM6800 menu. Note the following:

Port 2 defaults to ASCII and RS-232.

Ports 7 and 8 can be set to ASCII and RS-232 by using the CM6800 manager program (refer to Figure 63) or by using a CM6800 menu (refer to Figure 60).

Pelco recommends using Port 2.

Figure 61. Manager Screen

Figure 62. Menu Screen

SET SERIAL PORT 07

DEVICE: ASCII

TYPE: RS232

BAUD RATE: 9600

PARITY: ODD

DATA BITS: 8

STOP BITS: 1

RETURN

84 C2907M-D (4/05)

CONNECTING PELCONET TO A CM6800 AND KBD200A FOR REMOTE CONTROL Refer to Figure 63. This conguration lets an operator view and control cameras with a remote KBD200A keyboard. All settings are done in the CM6800 manager program or through a CM6800 menu. Note the following:

Port 2 defaults to ASCII and RS-232.

Ports 7 and 8 can be set to ASCII and RS-232 by using the CM6800 manager program (refer to Figure 63) or by using a CM6800 menu (refer to Figure 60).

Pelco recommends using Port 2.

Figure 63. Using PelcoNet with CM6800 and KBD200A to Provide Remote Control

Vi deo In

75 Audio I/O

Powe r

ETHERNET CONNECTION TO NETWORK (LAN/WAN)

TRANSMITTER

BAUD RATE DATA BITS PARITY STOP BITS

9600 8 ODD 1

2-RX 3-TX 5-GND

SPECTRA COAXITRON PROTOCOL

PELCONET TRANSPARENT DATA PORT

2 RXD.............................. 3 TXD.............................. 5 GND............................

CM6800E-48X8 COM 2 8 TXD 1 RXD 5 GND

6800 MATRIX COM 2 PORT SETTINGS:

BAUD RATE DATA BITS PARITY STOP BITS

9600 8 ODD 1

NOTE: FIRMWARE VER 4.0 OR LATER REQUIRED. SET KEYBOARD DIP SWITCHES - SWITCH 6 ON, SWITCHES 5 AND 8 OFF, SWITCHES 1 - 4 FOR ADDRESS ACCORDING TO THE TABLE IN THE KBD200A MANUAL.

Vi deo Ou t

75 Audio I/O

Powe r

RECEIVER

ETHERNET CONNECTION TO NETWORK (LAN/WAN)

12 V

TX(-)RX(-)

KBD200A

STRAIGHT CABLE

PV140 ORDERED SEPARATELY

12 VAC

1 2 3 4

8 7 6 5

GND

RX(+) TX(+)

2-RX 3-TX 5-GND RJ-45 WALL BLOCK

AND STRAIGHT CABLE SUPPLIED

PELCONET CM6800 ASCII SETUP

TRANSPARENT DATA PORT USING INTERNET EXPLORER SET TRANSPARENT DATA PORT SETTINGS:

PELCONET REMOTE KBD200A ASCII MODE SETUP

COM2 : RS232

COM1 : RS232/422/485

COM2 : RS232

COM1 : RS232/422/485

TRANSPARENT DATA PORT USING INTERNET EXPLORER, SET TRANSPARENT DATA SETTINGS ON BOTH PELCONET RECEIVER AND TRANSMITTER:

BAUD RATE DATA BITS PARITY STOP BITS

9600 8 ODD 1

C2907M-D (4/05) 85

Appendix B Frequently Asked Questions (FAQs) 1. What Pelco devices can I control from my computer with PelcoNet?

PelcoNet can control the following from Internet Explorer:

Spectra and Esprit

Genex multiplexer

CM9760 matrix (requires CM9700 data translator)

CM9740 matrix (requires CM9700 data translator)

CM9502 matrix (through integrated ASCII port)

CM8500 matrix (requires latest CM8500 data translator)

CM6700 matrix (through integrated ASCII port, COM 2)

CM6800 matrix

2. Can I view PelcoNet over the Internet?

Yes. You will need a static IP address and enough bandwidth to view live video. Pelco recommends a minimum of 250 Kbps for medium image quality. Also check with your ISP to verify the correct TCP and UDP ports are open through any routers or rewalls through which you will connect.

3. How many connections does PelcoNet support? Can more than one receiver connect to a transmitter at the same time?

Yes. PelcoNet can support up to 25 simultaneous connections. To do so, all hubs, switches, and routers must support multicasting (IGMP), and PelcoNet must be congured to use multicasting. If the network hardware does not support this, then the maximum number of simulta- neous connections is ve.

4. Can I enlarge the picture size in the browser?

Yes. You can select from two different image sizes in PelcoNet with the browser: 352 x 288 or 704 x 576.

5. What software does PelcoNet require?

PelcoNet works with Internet Explorer 6.0 or higher. An ActiveX plug-in and Microsoft Virtual Machine are also required for Internet Explorer to get live video. All software is included.

6. Can I control other manufacturers equipment from the browser?

Not at this time.

7. Can I record video with PelcoNet?

Yes. PelcoNet can record video to the hard drive of the viewing PC or onto the NET350 itself using the CompactFlash interface. The video is recorded in MPEG-4 format, which allows playback through either the browser or the proprietary MPEG Viewer software included on the resource CD.

8. Everything is wired correctly but I do not have any control from the browser. What else could be wrong?

The transparent port settings should be set to match the equipment to which PelcoNet is connected.

Also, in Internet Explorer, the Microsoft Virtual Machine should be enabled. To do so: on the Tools menu, select Internet Options. Then select the Advanced tab. Locate the option Microsoft VM. Place a checkmark next to Java Console Enabled and JIT compiler for virtual machine enabled. Reboot your computer.

These options are required for the Java applets in PelcoNet to function properly.

9. Can I control the Genex multiplexer from the browser and have a local KBD4000?

Yes. You must have Genex version 4.1 or higher for Genex units manufactured before November 22, 2002or version 1.12 or higher for units manufactured on or after that date. (The version numbering was restarted in 2002, which is why newer units have a smaller version num- ber.) These versions let you connect a KBD4000 to the COM IN port, and PelcoNet to the COM OUT port. This gives you both local and remote control. Refer to Connecting PelcoNet to the COM OUT RS-422 Port on a Genex Multiplexer in Appendix A for detailed information.

86 C2907M-D (4/05)

10. Can I control the Genex multiplexer server?

Not at this time.

11. Can I use DHCP (dynamically assigned IP address) with PelcoNet?

No.

12. What type of compression does PelcoNet NET350 use?

PelcoNet uses the MPEG-4 industry standard for video teleconferencing over the Internet. It provides the most effective use of bandwidth with excellent video quality.

13. I do not get live video in the browser but server push is working. What could be wrong?

Verify that the ActiveX plug-in is installed and that your video is set to 16-bit color. Also check with your network administrator to verify that the TCP/IP ports PelcoNet uses are not being ltered and that you have enough bandwidth.

14. How do I program PelcoNet with HyperTerminal?

Using a null modem cable, connect a COM port on your PC to the COM 1 port on PelcoNet. Open HyperTerminal and set the port to use 19200, 8, N, 1, and No Flow Control. Type ?, and follow the help menu.

15. How much bandwidth does PelcoNet use?

PelcoNets bandwidth is adjustable. You can set it from 9.6 kbps up to 5000 kbps. Pelco recommends a minimum of 250 Kbps for live video at medium image quality. Check with your network administrator for how much bandwidth to use.

16. Can I use PelcoNet with a DSL or cable connection?

Yes. You will need a static IP address from your provider. Also verify what kind of bandwidth you will get since it varies by location. Verify that your provider is not ltering the TCP/IP ports that PelcoNet uses.

17. Is an RS-232 to RS-422/485 converter required for control with PelcoNet?

No. The NET350s COM 1 port supports RS-232, RS-422, and RS-485.

18. What TCP/IP ports should I use with PelcoNet?

If you will be using PelcoNet in a LAN environment, Pelco recommends all TCP/UDP ports above 1024 be opened. Also, if you will use a time server, TCP port 37 must be opened.

If you will be using PelcoNet in a WAN environment, Pelco recommends changing the Video/Audio transmission setting to TCP in the Network Settings configuration page. This makes PelcoNet use port 80 and whatever source port the client computer chooses.

C2907M-D (4/05) 87

Index

A Alarm indicator 39 Alarm input 25, 39 Alarm recording on 50 Alarm recording scheduler 48 Alarm recording tab 46 Alarm recording time 50 Audio settings configuration page 35 Auxiliaries (matrix) 59 Average n (frames) 39

B Backing up a file onto a computer 67 Baud rate 42, 43, 44 Bistable 41 Box-to-box connection 27

C Camera (Genex) 60 Camera (matrix) 58 Camera (name) 34 Camera name stamping 34 COM 1 Interface Setting 42 Com 1 interface settings page 42 Com 2 interface settings configuration page 43 CompactFlash 64 Configuration pages alarm settings 37 Configuration pages audio settings 35 Configuration pages COM 1 interface settings 42 Configuration pages COM 2 interface settings 43 Configuration pages - general settings 31 Configuration pages general settings 31 Configuration pages keyboard 44 Configuration pages media recording settings 46 Configuration pages network settings 45 Configuration pages relay settings 41 Configuration pages video settings 33 Configuration types 27 Configuration upload 33 Configuration using a terminal program 50 Configuration using a Web browser 27 Connect on alarm 40 Connecting a relay 26 Connecting audio 24 Connecting power 26 Connecting to a LAN 26 Connecting to various components 75 Connecting video 23

D Data bits 42, 43, 44 Data terminals (connecting) 24 Datarate 34 Date format 32 Default IP address 45 Default IP addresses 55 Display alarm stamping 34 Displayed alarm message 34

E Enable audio encoder 36 Enter partition settings! 46 Esprit control page 62

F Frame skip ratio 34 Free on this partition 50 Front panel components 11

G Gateway IP address 45 General settings configuration page 31 Genex control page 59 Genex protocol ID 42

H Half-duplex mode 42 Hardware version 32 Home page 28

I Idle state 41 Indicator buttons (live page) 55 Installation (hardware) 23 Interface mode 42 Intra frame distance 34 IP address 8

K Keyboard settings configuration page 44

L LEDs definition 69 Live video 56 Live video auto-connect 40 Live video control 57 Live video receiver IP address 40 Local sensitivity 39

M Macros (matrix) 59 Matrix control page 58 Media Playback Screen 66 Media recording settings configuration pages 46 Menu tree 29 Microsoft Virtual Machine enabling 56 Minimum PC requirements 9 Monitor (Genex) 60 Monitor (matrix) 58 Monostable 41 Motion detection 39 Motion tracking 39 MPEG-4 encoder 1/2 button 34 Multicast audio port MPEG-4 46 Multicast group IP address 45 Multicast packet TTL 46

88 C2907M-D (4/05)

Multicast streaming 45 Multicast video port encoder 1/2 46 Multicasting protocols 10

N Name of encoder 34 NET-Manager 28 Network administrator instructions 9 Network settings configuration page 45 Number of alarms 50 Number of video receiver address 40

O Object min size (nxn blocks) 39 Operating mode 41

P Parameter preset 34 Parity 44 Parity check 42, 43 Partition name 50 Partition number 50 Partition selection 46 Partition total size 50 Password 32 Password confirm 32 Password level 32 Password settings 32 Patterns (Esprit) 62 Patterns (Genex) 60 Patterns (matrix) 59 Patterns (Spectra) 61 PC recording/viewing 63 Peripherals (connecting) 25 Pin assignments 24 Preset parameter name 34 Presets (Esprit) 62 Presets (Genex) 60 Presets (matrix) 59 Presets (Spectra) 61 Programming menus (Esprit) 62 Programming menus (Spectra) 61 Properties button 46

R Rear panel components 11 Recording active 46 Recording the video display onto CompactFlash 64 Recording the video display onto the PC 64 Relay follows 41 Relay name 41 Relay settings configuration page 41 Remaining for recording 50 Remote receiver password 40 Reset this parameter preset 34 Resetting PelcoNet 68

S Select area button 39 Sequence (Genex) 60 Serial interface 10

Serial port function 42, 43 Server push 56 Server push display 57 Server push page 55 Snapshots (record from video) 64 Snapshots (recording from file) 67 Snapshots (viewing) 64 Software upload 33, 68 Software version 10, 32 Specifications 71 Spectra control page 60 Spectra/Esprit protocol ID 42 Stop bits 42, 43, 44 Stop/Start buttons 46 Storing Files 63 Subnet mask 45

T Terminal program receiver menu structure 53 Terminal program transmitter menu structure 52 Time recording scheduler 48 Time recording tab 46 Time server IP address 32 Time stamping 34 Time zone 32 Total used size from partition 50 Tracker 39 Trigger relay 41 Troubleshooting 69 Type of recording 50

U Unified picture detection 39 Unit Date 32 Unit ID 32 Unit IP address 45 Unit name 32 Unit time 32 Upload progress 33 Used alarmtracks from partition 50 Used filetracks from partition 50

V Video loss alarm 39 Video motion alarm 39 Video on a Web browser 56 Video page 55 Video page indicators 55 Video recording 50 Video resolution 34 Video settings configuration page 33 Video via transmitter-to-receiver 12 Video/audio transmission 45 Viewing a file 66 Viewing the video display 65

W Web browser 9 Web browser control pages 57

C2907M-D (4/05) 89

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

Five years on FT/FR8000 Series ber optic products.

Three years on Genex Series products (multiplexers, server, and keyboard).

Three years on Camclosure and xed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X camera models, which have a ve-year warranty.

Two years on standard motorized or xed focal length lenses.

Two years on Legacy, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series xed dome products.

Two years on Spectra, Esprit, ExSite, and PS20 Scanners, including when used in continuous motion applications.

Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).

Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura Series distributed network-based video products.

One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specic use or application made of the Products. Pelcos liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of prot and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specic legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: 1. Model and serial number 2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number 3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identied with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to: Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to: Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to: Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933

REVISION HISTORY

Manual # Date Comments C2907M 10/03 Original version. C2907M-A 12/03 Changed parity from odd to none in text and onFigure 56. C2907M-B 3/04 Added information on the NET350R Video Decoder Settings page. Revised the Troubleshooting section. Replaced the KBD4000 with a CM9760-KBD in Figure 50.

Revised the denition for the Time server IP address eld to remove NTP. Added audio information to the Specication section. C2907M-C 12/04 Added information, application, and connection drawing about the Local COM Interface Keyboard feature. Included information on the Video Watermarking

MPG-4, Video Quality Settings, and Field Mode elds that were added to the Video Conguration page. Updated the menu tree, the Setup page, and the Device Con- trol page to reect these changes. Corrected Figure 56 (now Figure 60) in which a CM9760-NW1 was incorrectly labled a CM9760-CC1. Added NTSC pixel resolu- tion to the Specications section.

C2907M-D 4/05 Revised Figure 16, corrected Figure 24, and added a new Figure 26. Also corrected the old Figure 26 (which is now the new Figure 27). Added "4CIF" and "custom" to the description of the Video Resolution eld. Corrected NTSC video image size in the Specications section. Made numerous formatting changes.

Pelco, the Pelco logo, Spectra, Esprit, Genex, Camclosure, Legacy, and Coaxitron are registered trademarks of Pelco. Copyright 2005, Pelco. All rights reserved. PelcoNet is a trademark of Pelco. Microsoft, Windows, DirectX, and ActiveX are registered trademarks of Microsoft Corporation in the United States and/or other countries. ATI RADEON is a trademark of ATI Technologies Inc. Pentium 4 is a registered trademark of Intel Corporation. Parhelia is a trademark of Matrox Technologies Inc. Compact Flash is a registered trademark of SanDisk Corporation. NVIDIA is a registered trademark of NVIDIA Corporation.

Worldwide Headquarters 3500 Pelco Way

Clovis, California 93612 USA

USA & Canada Tel: 800/289-9100 Fax: 800/289-9150

International Tel: 1-559/292-1981 Fax: 1-559/348-1120

www.pelco.com

ISO90

Manualsnet FAQs

If you want to find out how the PelcoNet NET350 Pelco works, you can view and download the Pelco PelcoNet NET350 C2907M-D Transmitter Operations Manual on the Manualsnet website.

Yes, we have the Operation's Manual for Pelco PelcoNet NET350 as well as other Pelco manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operation's Manual should include all the details that are needed to use a Pelco PelcoNet NET350. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Pelco PelcoNet NET350 C2907M-D Transmitter Operations Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Pelco PelcoNet NET350 C2907M-D Transmitter Operations Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Pelco PelcoNet NET350 C2907M-D Transmitter Operations Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Pelco PelcoNet NET350 C2907M-D Transmitter Operations Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Pelco PelcoNet NET350 C2907M-D Transmitter Operations Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.