Pelco KBD4002 C581M-B Keyboard Operation Manual PDF
en
Summary of Content for Pelco KBD4002 C581M-B Keyboard Operation Manual PDF
Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA www.pelco.com
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
KBD4002 Genex Multiplexer
Keyboard
Installation/ Operation Manual
C581M-B (1/04)
LIVE/VCR
WIDE
CLOSE
FAR
IRIS
1 2
34 5
67 8
9 0
CLEAR
CAM
KBD4002MADE IN USA.
PAN / TILT
UNIT MAIN
SPOT SEQ
VIEW PATTERN PRESET
ON OFF
MONITOR
AUX
2 Pelco Manual C581M-B (1/04)
Pelco Manual C581M-B (1/04) 3
CONTENTS
Section Page
IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 4 REGULATORY NOTICES ..................................................................................................4
DESCRIPTION ...................................................................................................................5
INSTALLATION ..................................................................................................................6 MULTIPLEXER MODE INSTALLATION.....................................................................6 MULTIPLEXER SERVER MODE INSTALLATION .....................................................7
OPERATION ......................................................................................................................8
PROGRAMMING ..............................................................................................................19 PASSWORD ............................................................................................................. 20 MENUS .....................................................................................................................20
SYSTEM SETUP (VIEW KEY) .......................................................................... 20 ADVANCED SYSTEM SETUP (VIEW KEY) ..................................................... 22 RECORD SETUP (LIVE/VCR KEY) .................................................................. 24 CUSTOM VCR SETUP (LIVE/VCR KEY) ......................................................... 26 CAMERA SETUP (NUMBER AND CAM KEYS) ............................................... 27 ACTIVITY DETECTION MASK SETUP ............................................................ 29 SEQUENCE SETUP (SEQ KEY) ...................................................................... 30 HELP MENU .....................................................................................................31
MULTIPLE CAMERA DISPLAY SETUP .................................................................... 32
PROGRAMMING THE PICTURE-IN-PICTURE DISPLAY ( KEY) ............ 32
PROGRAMMING THE 4-CAMERA DISPLAY ( KEY) ................................ 32
PROGRAMMING THE 9-CAMERA DISPLAY ( KEY) ................................ 33
PROGRAMMING THE 16-CAMERA DISPLAY ( KEY) .............................. 33 PROGRAMMING MENU DEFAULTS ....................................................................... 34 PROGRAMMING A PRESET .................................................................................... 35 PROGRAMMING A PATTERN .................................................................................. 35
TROUBLESHOOTING ...................................................................................................... 36
SPECIFICATIONS............................................................................................................. 37
WARRANTY AND RETURN INFORMATION.................................................................... 39
LIST OF ILLUSTRATIONS
Figure Page
1 Switch Locations and RJ-45 Jack Pinouts ......................................................... 7 2 KBD4002 Keyboard Definitions .........................................................................9 3 Basic System Setup Menu ................................................................................ 20 4 Advanced System Setup Menu ......................................................................... 22 5 Basic VCR Setting Menu .................................................................................. 25 6 Custom VCR Setup Menu .................................................................................26 7 Basic Camera Menu ......................................................................................... 27 8 Activity Detection Mask ..................................................................................... 29 9 Camera Sequence Menu .................................................................................. 30 10 Help Menu .........................................................................................................30
LIST OF TABLES
Table Page
A Keyboard Addresses ..........................................................................................7 B Operation Guide ................................................................................................ 11 C Camera Numbers with Switch 7 ON ................................................................. 19 D VCR Types ........................................................................................................ 25 E Programming Menu Defaults ............................................................................ 34
4 Pelco Manual C581M-B (1/04)
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.
3. Only use replacement parts recommended by Pelco.
4. After replacement/repair of this units electrical components, conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry.
The product and/or manual may bear the following marks:
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
C A U T I O N :
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
REGULATORY NOTICES
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or =television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the re- ceiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Pelco Manual C581M-B (1/04) 5
DESCRIPTION
The KBD4002 Genex Multiplexer Keyboard is a full-function keyboard controller for the Genex MX4000 Multiplexer and the Genex MX4000SVR Multiplexer Server.
This manual covers the KBD4002 keyboards operation with the duplex and simplex models of the multiplexer. The differences, as they pertain to the keyboard, will be indicated in the text and art wherever necessary.
There are two modes of operation - multiplexer mode and multiplexer server modedepending on whether the keyboard is connected to a multiplexer or to a server.
In the multiplexer mode, a single keyboard interfaces up to 16 multiplexers that are daisy-chained together. With 9-channel multiplexers, the keyboard can control up to 144 cameras; with 16-channel multiplexers, up to 256 cameras can be controlled.
In the multiplexer server mode, up to four keyboards can be connected to a server, which interfaces up to eight multiplexers. Up to 72 cameras can be controlled with 9-channel multiplexers or 128 cameras with 16-channel multiplexers.
In addition to performing all the control functions that can be done from the front panel of the multiplexer, the keyboard features additional keys for full control of fixed speed and variable speed pan, tilt, and lens functions. Variable speed control is accomplished with the number keypad using the select-a-speed feature. With select-a-speed, each digit (1-9) represents a relative pan and tilt speed. The number 1 represents the slowest speed available while the number 9 speed equates to turbo pan (for those receivers capable of supporting turbo pan speed). When the number 9 is entered, the tilt will operate at the number 8 speed. Entering the number 0 sets a mid-range speed. The keyboard can also operate presets, auxiliaries, and patterns and can be used to program the multiplexer or server.
6 Pelco Manual C581M-B (1/04)
INSTALLATION
The following parts are supplied:
1 KBD4002 keyboard 1 25-foot (7.6 m) data cable
There are two modes of operationmultiplexer mode and multiplexer server modedepending on whether the keyboard is connected to a multiplexer or to a server.
In the multiplexer mode, a single keyboard is plugged into the back of a Genex MX4000 Multiplexer.
In the multiplexer server mode, up to four keyboards can be connected to the back of a Genex MX4000SVR Multiplexer Server. A KBDKIT(-X) is required for each keyboard connected to the remote keyboard port.
Proceed to the Multiplexer Mode Installation or Multiplexer Server Mode Installation section.
MULTIPLEXER MODE INSTALLATION
1. Remove the DIP switch cover plate from the rear of the keyboard (refer to Figure 1).
2. Set the switches (refer to Figure 1 for switch locations).
ADDRESS Set switches 1, 2, and 3 OFF. This is address 0, which selects the multiplexer mode of operation.
COMMUNICATION MODE Set switch 4 OFF to enable the polled communication mode. Use this for normal keyboard operation.
Set switch 4 ON to put the keyboard in the non-polled communication mode. Use this when the keyboard communicates remotely over communications media that will not support the polled mode. This is any communications media that introduces a significant delay in the transmission of data (for example, phone line transmission systems). In the non-polled mode, the keyboard can be used to control multiplexer(s) only. The non-polled mode is not supported by the multiplexer server.
UNUSED Leave switch 5 OFF. It is not used.
TURBO MODE Set switch 6 ON to enable the turbo pan feature. Set the switch OFF to disable the turbo pan feature.
CAMERA ADDRESS MODE There are two modes for addressing cameras: by addressing all the cameras consecutively from 1-256 (refer to Table C) or by addressing the cameras in groups of 16 according to the multiplexer they are connected to. For example, multiplexer 1, cameras 1-16; multiplexer 2, cameras 1-16, etc.
Set switch 7 ON if you want to address all cameras consecutively.
Set switch 7 OFF if you want to address cameras according to the multiplexer they are connected to.
PROGRAMMING MODE Set switch 8 ON to program the multiplexer and camera presets and patterns from the keyboard. Set the switch OFF to disable programming.
NOTE: The KBD4002 keyboard in combination with a Genex multiplexer provides Coaxitron control of pan, tilt, and lens functions.
When used with 15-bit standard Coaxitron receivers, such as the CX9000 Series, the PT7700, and the ED25/27/28/29, the KBD4002 in conjunction with the multiplexer supports all pan, tilt, and lens functions, and AUX on/off. The keyboard will not set or call presets or support preset scanning.
When used with 32-bit extended Coaxitron receivers, such as Esprit, Intercept, Spectra, and LRD41C21/LRD41C22 Series, the KBD4002 in conjunction with the multiplexer will support all the functions of a 15-bit receiver, including the setting and calling of presets and patterns. It will not support programming of labels for presets or patterns. If labels for presets or patterns are required, they would need to be programmed with a different control, such as the MPT9500.
Pelco Manual C581M-B (1/04) 7
3. Replace the cover on the back of the keyboard.
4. A 25-foot (7.6 m) data cable with RJ-45 connectors is supplied with the keyboard. Plug one end of the cable into the back of the keyboard and plug the other end into the COM IN connector on the back of the multiplexer.
The keyboard receives power from the multiplexer. The LED display will light momentarily when the keyboard receives power. The LED will stay on when you enter a multiplexer address.
5. Peel off the protective covering over the LED display in the upper left corner of the keyboard.
MULTIPLEXER SERVER MODE INSTALLATION
1. Remove the DIP switch cover plate from the rear of the keyboard (refer to Figure 1).
2. Set the switches (refer to Figure 1 for switch locations).
ADDRESS Refer to Table A to set the address of the keyboard.
UNUSED Switches 4 and 5 are not used in the multiplexer server mode. They must be placed in the OFF position.
TURBO MODE Set switch 6 ON to enable the turbo pan feature. Set the switch OFF to disable the turbo pan feature.
CAMERA ADDRESS MODE There are two modes for addressing cameras: by addressing all the cameras consecutively from 1-256 (refer to Table C) or by addressing the cameras in groups of 16 according to the multiplexer they are connected to; for example, multiplexer 1, cameras 1-16; multiplexer 2, cameras 1-16, etc.
Table A. Keyboard Addresses
Keyboard Switch Settings
Address 1 2 3
1 ON OFF OFF
2 OFF ON OFF
3 ON ON OFF
4 OFF OFF ON
Figure 1. Switch Locations and RJ-45 Jack Pinouts
NOTE: If the keyboard will be connected to a server that will operate in the paired mode configuration, only addresses 1 and 3 can be used. Refer to the server manual for information about the paired mode configuration.
NOTE: For distances over 25 feet (7.6 m), you must order the KBDKIT(-X) Remote Keyboard Wiring Kit. Refer to the KBDKIT(-X) manual for installation procedures.
O N
1 2 3 4 5 6 7 8
}
PIN 1
1 TX+ 5 GND 2 TX 6 3 12 VAC/DC 7 RX 4 NONPOLAR 8 RX+
RJ-45 JACK PINOUTS
8 Pelco Manual C581M-B (1/04)
Set switch 7 ON if you want to address all cameras consecutively.
Set switch 7 OFF if you want to address cameras according to the multiplexer they are connected to.
PROGRAMMING MODE Set switch 8 ON to program the server and the multiplexer. Set the switch OFF to disable programming.
3. Replace the cover on the back of the keyboard.
4. Connect the keyboard to the MX4000SVR Multiplexer Server. A maximum of four keyboards can be connected to the server. One keyboard can be connected to the LOCAL KEYBOARD port on the server, and up to three keyboards can be connected to the REMOTE KEYBOARD(S) port on the server. Or four keyboards can be connected to the remote.
LOCAL KEYBOARD PORT To connect the keyboard to the LOCAL KEYBOARD port, a 25-foot (7.6 m) data cable with RJ-45 connectors is supplied with the keyboard. Plug one end of the cable into the back of the keyboard and plug the other end into the LOCAL KEYBOARD port on the server. Refer to the multiplexer server manual for instructions.
The keyboard receives power from the multiplexer. The LED display will light when the keyboard receives power. The display will show the address of the multiplexer with which the keyboard is communicating.
REMOTE KEYBOARD(S) PORT To connect a keyboard(s) to the REMOTE KEYBOARD(S) port on the server you must order a KBDKIT(-X) for each keyboard. Follow the instructions that are supplied with the kit. Refer to Figure 1 for the keyboard RJ-45 pin-outs.
The keyboard receives power from the transformer. The LED display will light when the keyboard receives power. The display will show the address of the multiplexer with which the keyboard is communicating.
5. Peel off the protective covering over the LED display in the upper left corner of the keyboard.
OPERATION
IMPORTANT NOTE ABOUT PROGRAMMING
When the keyboard is plugged into a multiplexer or multiplexer server, the keyboard is ready to operate. However, some minimal programming may be required to make your system work.
MULTIPLEXER The default settings for the duplex and simplex multiplexers are not the same, and it should not be assumed that there is nothing more to do after connecting the keyboard to the system. Below are the minimum things to check.
1. To allow the keyboard to communicate with multiplexers in the polled mode (switch 4 OFF), you must designate one multiplexer (any one) as the master and all the others as slaves. If you have just one multiplexer, it must be the master. In the non-polled communication mode (switch 4 ON), all multiplexers must be slaves (the keyboard is the master).
Set the master/slave designation from the front panel of the multiplexer, not from the keyboard. Go to the Advanced System Setup menu (refer to multiplexer manual) and select master or slave in the COMM. TYPE menu item. The default is SLAVE for duplex multiplexers and MASTER (KBD T/D) for simplex multiplexers.
Pelco Manual C581M-B (1/04) 9
2. If you have more than one multiplexer, each one must have its own address (Unit ID in the Advanced System Setup menu). If you have a server, the multiplexer address must match the input on the server to which it is connected; for example, if the multi- plexer is connected to input 3 on the server, set the multiplexer address to 3. Set the address from the front panel of the multiplexer, not from the key- board.
3. If you have moveable cameras (they must be Coaxitron compatible), you must pro- gram the Coaxitron format for each camera (Camera menu). The duplex multiplexer COAXITRON FORMAT default setting is OFF, while the simplex default setting is EXTENDED. Programming can be done from the front panel of the multiplexer or from the keyboard (refer to the Programming section for keyboard instructions).
MULTIPLEXER SERVER Below is the minimum you should check.
If you intend to control two monitors from one keyboard (paired mode), you must change the settings for the monitors (Monitor menu). Programming the server can only be done from the keyboard. Refer to the server manual for instructions.
IMPORTANT NOTE ABOUT COAXITRON CONTROL OF CAMERAS
The KBD4002 keyboard provides Coaxitron control of pan, tilt, and lens functions.
The duplex multiplexer COAXITRON FORMAT (refer to the Camera Setup section) default setting is OFF and must be changed in order to use Coaxitron control. The simplex multiplexer default setting is EXTENDED and 32-bit Coaxitron control can be used without changing the setting.
When used with 15-bit standard Coaxitron receivers, such as the CX9000 Series, the PT7700, and the ED25/27/28/29, the KBD4002 supports all pan, tilt, and lens functions, and AUX on/off. The keyboard will not set or call presets or support preset scanning.
When used with 32-bit extended Coaxitron receivers, such as Esprit, Intercept , Spectra, and LRD41C21/LRD41C22 Series, the KBD4002 will support all the functions above, including the setting and calling of presets and patterns. It will not support programming of preset or pattern labels. If labels for presets or patterns are required, they would need to be programmed with a different control, such as the MPT9500.
IMPORTANT NOTE ABOUT DIFFERENCES IN SIMPLEX AND DUPLEX MULTIPLEXER MODES OF OPERATION
The simplex multiplexer has three modes of operation: live, VCR, and record.
In the live mode, the main monitor can show live video both in full-screen or multiple-screen views. You cannot record in the live mode. The multiplexers DISPLAY/RECORD LED is OFF.
In the VCR mode, the main monitor will show full-screen or multiple-screen views of videotape playback. You cannot record in the VCR mode. The multiplexers DISPLAY/ RECORD LED is OFF.
In the record mode, the main monitor will show live video of an individual camera in full-screen view only. You can record only when in the record mode. While recording, all cameras are being recorded simultaneously. The multiplexers DISPLAY/RECORD LED is ON.
The duplex multiplexer has two modes of operation: live and VCR.
In the live mode, the main monitor will show live video both in full-screen or multiple-screen views. You can record while in this mode. The multiplexers LIVE/VCR LED is ON.
In the VCR mode, the main monitor will show full-screen or multiple-screen views of videotape playback. You can record in the VCR mode if you have a second VCR con- nected to the VCR OUT jack on the multiplexer. The multiplexers LIVE/VCR LED is OFF.
10 Pelco Manual C581M-B (1/04)
1. LED DISPLAY Displays the address of the multiplexer (from 1-16) with which the keyboard is communicating.
2. LIVE/VCR KEY Selects the source of video to display on the monitor(s). LIVE is live video from the cameras. VCR is recorded video that is played back from a VCR.
The simplex multiplexer must be in the record mode to record video. Check the main monitor screen to see that it indicates REC. Press the LIVE/VCR key to change modes.
3. ZOOM KEY Zooms in (2X or 4X) on the displayed camera. Use the pan/tilt keys to control the zoom location.
4. PIP KEY Displays on the main monitor a picture-in- picture insert on top of the full-screen display.
5. FOUR-CAMERA DISPLAY KEY Press once to display a group of four cameras on the main monitor. Repeat pressing to display other groups.
6. NINE-CAMERA DISPLAY KEY Press once to display a group of nine cameras on the main monitor. Press again to display second group.
7. 16-CAMERA DISPLAY KEY Press once to display all 16 cameras on the main monitor.
8. AUXILIARY KEYS Turn receiver auxiliary functions on and off.
9. PRESET KEY Sends a camera to a preset: Enter the preset number and then press this key. Also is used for programming presets.
10. PATTERN KEY Press to begin a pattern. Also is used to program a pattern.
11. PAN/TILT KEYS Provide motion control to receiver and are used to navigate through the multiplexer programming menus. Variable speed control is accomplished with the number keypad using the select-a-speed feature. With select-a-speed, each digit (1-9) represents a relative pan and tilt speed. The number 1 represents the slowest speed available while the number 9 speed equates to turbo pan* (for those receivers capable of supporting turbo pan speed). When the number 9 is entered, the tilt will operate at the number 8 speed. Entering the number 0 sets a mid-range speed.
12. VIEW KEY Press to enter program mode for multiplexer/multiplexer server.
13. LENS CONTROL KEYS Control camera lens functions: focus, iris and zoom.
14. SEQ KEY Starts/stops a sequence.
15. CLEAR KEY Press to clear a numeric entry.
16. CAM KEY Selects a camera: Enter the camera number and then press this key.
17. NUMBER PAD Enter numbers.
18. MONITOR KEYS Select the main or spot monitor for viewing individual cameras. A green LED above each key indicates which monitor is selected.
19. UNIT KEY Selects the multiplexer with which the keyboard communicates: Enter the address of the multiplexer (1-16) and then press this key.
Figure 2. KBD4002 Keyboard Definitions
For complete instructions on how to use the keys, refer to Table B, Operation Guide.
* The turbo pan feature may be disabled. Place switch 6 on the rear panel DIP switch block in the off position. See Figure 1.
KBD4002 MADE IN USAPAN / TILT
ZOOM
FOCUS IRIS
WIDE FAR CLOSE
OPEN
TELE
NEAR
UNIT MAIN SPOT SEQ VIEW PATTERN PRESET ON OFF
AUX MONITOR
LIVE/VCR
CAM 0 CLEAR
7 8 9
4 5 6
1 2 3
1 2 3 4 5 6 7
8
9
10
13
11121415 16
17
18
19
*
Pelco Manual C581M-B (1/04) 11
Table B. Operation Guide
NOTE: References to switch 7 in this table refer to the switch behind the panel on the back of the keyboard. There are two modes for addressing cameras: by addressing all the cameras consecutively from 1-256 (switch 7 ON, refer to Table C) or by addressing the cameras in groups of 9 or 16 according to the multiplexer they are connected to (switch 7 OFF); for example, multiplexer 1, cameras 1-9 or 1-16; multiplexer 2, cameras 1-9 or 1-16, etc.
OPERATION KEYBOARD COMMAND RESULT
Enter a number, 1-9, from the number keypad followed by one of the pan/tilt keys. Each number represents a relative pan and tilt speed with number 9 equaling turbo pan speed (on equipped receivers) and number 1 equaling crawl speed (the slowest speed). When the number 9 is entered, the tilt will operate at the number 8 speed. Entering the number 0 sets a mid-range speed.
1. Press the MAIN MONITOR key. The green LED over the MAIN key lights.
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
3. Press the LIVE/VCR key to select the mode of operation.
1. Press the SPOT MONITOR key. The green LED over the SPOT key lights.
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
Call a camera to the MAIN monitor.
Call a camera to the SPOT monitor.
(Continued on next page)
Stops a sequence if one is in progress. Displays the camera on the MAIN monitor.
Displays the camera on the SPOT monitor.
Use the select-a-speed feature to operate pan and tilt units with variable speed.
The speed that is selected will remain in memory until it is changed.
12 Pelco Manual C581M-B (1/04)
Table B. Operation Guide (Continued)
1. Go to the Advanced System Setup menu.
2. Press the pan/tilt keys so the cursor highlights SPOT MONITOR DISPLAY items.
3. Press the OPEN key until TRACK MAIN is displayed.
4. Exit the Advanced System Setup menu.
1. Go to the Advanced System Setup menu.
2. Press the pan/tilt keys so the cursor highlights SPOT MONITOR DISPLAY items.
3. Press the OPEN key until either SEQUENCE or BLANK is displayed.
4. Exit the Advanced System Setup menu.
1. Press the MAIN MONITOR key. The green LED over the MAIN key lights.
2. On the number pad, press the address number of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
3. Press the key below the 4, 9, or 16 icon.
4. Repeat pressing the key until the correct group is displayed (4 or 9 only).
5. Press the LIVE/VCR key to select the mode of operation.
OPERATION KEYBOARD COMMAND RESULT
(Continued on next page)
Exit main tracking.
Call a group of cameras to the MAIN monitor.
Exits main tracking mode.
Displays the group of cameras on the MAIN monitor.
Set main tracking. Spot monitor follows the camera switching that occurs on the main monitor in single screen mode. In multi-screen mode, the spot monitor switches to camera 1.
Allows only P/T/Z control while in main monitor mode. Press the SPOT key to have presets and patterns while in this mode.
Pelco Manual C581M-B (1/04) 13
Table B. Operation Guide (Continued)
1. Press the MAIN MONITOR key. The green LED over the MAIN key lights.
2. Select the camera that you want to display full size.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
3. Make sure the main monitor displays live video. If the video is not live, press the LIVE/VCR key.
4. Press the PIP icon key.
5. On the number keypad press the number of the camera you want to display in the insert. Then press the CAM key. (Note: Both cameras must be connected to the same multiplexer.)
6. To change the display in the insert, press the number of the camera, then press the CAM key.
7. To exit, press the PIP icon key.
1. Press the MAIN MONITOR key. The green LED over the MAIN key lights.
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number
of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
3. Press the LIVE/VCR key to select the mode of operation.
4. Press the key below the ZOOM icon. The zoom will be 2X. Press the key again for 4X zoom.
5. Use the pan/tilt keys to control the zoom location.
6. To exit, press the zoom icon key or the number of the camera, then press the CAM key.
OPERATION KEYBOARD COMMAND RESULT
(Continued on next page)
Zoom on a camera on the MAIN monitor.
Stops a sequence if one is in progress. Displays a 2X or 4X zoom of the camera selected on the MAIN monitor.
Display a picture-in- picture (PIP) insert on the MAIN monitor.
The full-size view appears on the MAIN monitor with the PIP insert.
NOTE: In order to change the camera shown on the full screen view, you must exit the PIP mode.
14 Pelco Manual C581M-B (1/04)
Table B. Operation Guide (Continued)
1. Press the MAIN MONITOR key. The green LED over the MAIN key lights.
2. Select a camera on the multiplexer that you want to sequence.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of a camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of a camera, then press the CAM key. Refer to Table C for camera numbers.
3. Press the LIVE/VCR key to select the mode of operation.
4. To sequence individual cameras, go to step 5. To sequence groups of cameras, press the key below the 4- or 9-screen icon, then go to step 5.
5. Press the SEQ key.
1. Press the SPOT MONITOR key. The green LED over the SPOT key lights.
2. Select a camera on the multiplexer that you want to sequence.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of a camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of a camera, then press the CAM key. Refer to Table C for camera numbers.
3. Press the SEQ key.
1. Press the MAIN or SPOT MONITOR key.
2. On the number pad, press the address number of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
3. Press the SEQ key.
OPERATION KEYBOARD COMMAND RESULT
Starts the sequence of individual cameras on the SPOT monitor.
Stops the sequence. The monitor displays video from the camera on which sequence stops.
Run a sequence of cameras from one multiplexer on the SPOT monitor. (SPOT MONITOR DISPLAY in the Advance System Setup menu must be in SEQUENCE.)
Stop a sequence of cameras on a multiplexer.
(Continued on next page)
Run a sequence of cameras from one multiplexer on the MAIN monitor.
Starts the pre-programmed sequence of individual cameras or groups of cameras on the MAIN monitor.
Pelco Manual C581M-B (1/04) 15
1. Select the desired multi-camera display.
2. Press and hold the multi-camera display key to enter the multi-screen programming mode. A bar will appear in the first camera location.
3. Use the pan/tilt keys to move the on-screen bar to the desired camera location for sequencing, and press sequence key to initiate the sequencing of all active cameras.
1. Hold down the SEQ key for approximately three seconds.
1. Follow the steps under Run a sequence of cameras from one multiplexer on the MAIN monitor or Run a sequence of cameras from one multiplexer on the SPOT monitor to start sequencing the cameras on the main and spot monitors of individual multiplexers that you want to sequence.
2. Hold down the SEQ key for approximately three seconds to start sequencing the multiplexers.
1. Press the key.
2. Press the SEQ key.
Press a pan/tilt key or select any camera.
Program the monitor in the Advanced System Setup menu.
Table B. Operation Guide (Continued)
Starts sequencing the multiplexers in numerical order, displaying the main monitor first, then the spot monitor. Monitors to be displayed are selected in the Set Sequence submenu of the Monitor menu of the server. As each monitor is displayed, it sequences. Sequencing appears on the monitor affiliated with the key- board; for example, if the keyboard is set for address 1, the sequence will appear on monitor 1.
Sequences all active cameras in the PIP display.
OPERATION KEYBOARD COMMAND RESULT
(Continued on next page)
Stop a sequence of multiplexers.
Call a camera or run a sequence of cameras on the AUX monitor (duplex multiplexer only).
Sequence multiplexers connected to a server and sequence cameras on a multiplexer(s).
Sequence the PIP display.
Sequence stops.
Monitor responds to programming instructions.
Starts sequencing the multiplexers in numerical order, displaying the main monitor first, then the spot monitor. Monitors to be displayed are selected in the Set Sequence submenu of the Monitor menu of the server. Sequencing appears on the monitor affiliated with the keyboard; for example, if the keyboard is set for address 1, the sequence will appear on monitor 1.
Sequence multiple cameras in one location of a 4-, 9-, or 16-camera display.
Sequence multiplexers connected to a server.
The sequence will run until the sequence key is pressed or until another camera or multi-screen display has been selected.
16 Pelco Manual C581M-B (1/04)
1. Press the MAIN or SPOT MONITOR key. The green LED over the MAIN or SPOT key lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in the Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup section).
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
3. On the number keypad press the number of the preset, then press the PRESET key. (Note: When calling preset 95 on Esprit or Spectra systems, hold the PRESET key until the menu appears on the screen.)
1. Press the SPOT MONITOR key. The green LED over the SPOT key lights.
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
3. On the number keypad press 97, then press the PRESET key.
With system in auto scan, press 97 on the number keypad, then press the PRESET key.
Table B. Operation Guide (Continued)
OPERATION KEYBOARD COMMAND RESULT
(Continued on next page)
Start random scan with 15-bit receiver.
Starts random scanning.
Start auto scan with 15-bit receiver.
Starts auto scanning.
Call a preset. Moves the camera to the preset location.
Pelco Manual C581M-B (1/04) 17
1. Press the SPOT MONITOR key. The green LED over the SPOT key lights.
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
3. On the number keypad press 96, then press the PRESET key.
1. Press the MAIN or SPOT MONITOR key. The green LED over the MAIN or SPOT key lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in the Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup section).
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
3. On the number keypad press 1, then press the PATTERN key.
4. To stop the pattern, press a pan/tilt key.
Table B. Operation Guide (Continued)
OPERATION KEYBOARD COMMAND RESULT
(Continued on next page)
Begin a pattern. The pattern operates until stopped.
Stops auto or random scanning, if operating, and activates manual scanning.
Start manual scan (or stop auto or random scan) with 15-bit receiver.
18 Pelco Manual C581M-B (1/04)
OPERATION KEYBOARD COMMAND RESULT
Table B. Operation Guide (Continued)
1. Press the SPOT MONITOR key. The green LED over the SPOT key lights.
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
3. On the number keypad press the number of the auxiliary you want to operate, then press the AUX ON or OFF key.
For duplex multiplexer, recording is done automatically. For simplex multiplexer, the multiplexer must be in the record mode (DISPLAY/RECORD LED is ON).
1. Press the MAIN MONITOR key. The green LED over the MAIN key lights.
2. On the number pad, press the address number of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
3. Press the LIVE/VCR key to put the multiplexer in the playback mode.
4. Select the cameras to play back from one of the following choices:
For an individual camera, press the number of the camera, then press the CAM key. If switch 7 is OFF, enter a camera number from 1-16. If switch 7 is ON, refer to Table C for camera numbers.
For multiple camera display, press the key below the 4, 9, or 16 icon.
For sequencing, select an individual or multiple camera display, then press the SEQ button.
5. Turn on the VCR and press the PLAY button.
Play a tape. Displays the recorded cameras in the selected format on the MAIN monitor.
Turn an auxiliary function on or off.
The auxiliary function operates.
Records all cameras connected to the multiplexer.
For simplex multiplexer, while the multiplexer is in the record mode (DISPLAY/RECORD LED on ON) you can only see a full-screen view of one camera (or one camera at a time if sequencing) on the main monitor, but all active cameras are being recorded.
Record a tape.
Pelco Manual C581M-B (1/04) 19
PROGRAMMING
This section applies only to programming the multiplexer. To program the multiplexer server, refer to the server manual.
Programming allows you to configure the multiplexer from the KBD4002 for the way that you want your system to operate. The multiplexer automatically selects the most common operating parameters. However, some minimal programming may be required to make your system work.
Programming of system, camera, and VCR setup; camera sequencing; and alarm and ac- tivity detection are done through on-screen menus that are displayed on the main monitor. A password can be enabled to prevent unauthorized access to the menus.
Programming of the picture-in-picture, and 4-, 9-, and 16-camera displays can be done directly without going through menus.
IMPORTANT NOTE Before the keyboard can be used to control the multiplexer(s), perform the following steps at the multiplexer(s) front panel.
1. Press the VIEW button for approximately three seconds. The basic SYSTEM Setup menu appears.
2. The currently selected menu item blinks. Use the arrow buttons to highlight AD- VANCED SETUP.
3. Press the +/- button. The Advanced System Setup menu appears. Skip steps 4 and 5 if your system has only one multiplexer.
4. Use the arrow buttons to move the cursor to UNIT ID.
5. Press the +/- button to select the UNIT ID of the multiplexer.
6. Use the arrow button to move the cursor to COMM.TYPE.
7. In the polled communication mode (switch 4 OFF), one multiplexer must be the master and all others slaves. In the non-polled mode (switch 4 ON), all multiplexers must be slaves.
8. Use the arrow button to go to EXIT. Press the +/- button to exit the menu. The keyboard can now be used to program the multiplexer(s).
NOTE: Whenever a multiplexer server is installed, programming the multiplexer must be done at the multiplexer front panel. In this situation, the multiplexer cannot be programmed from the +keyboard. The keyboard can onlybe used to program the multiplexer server, not the multiplexer.
Table C. Camera Numbers with Switch 7 ON
Multiplexer Cameras 9-channel 16-channel
1 1-9 1-16
2 17-25 17-32
3 33-41 33-48
4 49-57 49-64
5 65-73 65-80
6 81-89 81-96
7 97-105 97-112
8 113-121 113-128
9 129-137 129-144
10 145-153 145-160
11 161-169 161-176
12 177-185 177-192
13 193-201 193-208
14 209-217 209-224
15 225-233 225-240
16 241-249 241-256
20 Pelco Manual C581M-B (1/04)
PASSWORD
You can program the multiplexer to request a password for access to programming menus. The password is enabled in the Advanced System Setup menu (refer to the Advanced System Setup section).
The universal password is 3916 and cannot be changed. This password must be entered whenever one is requested. The password is entered from the keyboard by pressing each number followed by pressing the CAM key: 3, CAM, 9, CAM, 1, CAM, 6, CAM.
MENUS
To program from the keyboard you have to be in main monitor mode. Press the MAIN MONITOR key.
SYSTEM SETUP (View Key) To program the main basic system parameters:
1. Press the MAIN MONITOR key.
2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
3. Press the VIEW key for approximately three seconds. Type the password, if requested. The password must be entered by pressing each number key followed by pressing the CAM key. The System Setup menu appears. The currently selected menu item blinks.
4. Use the pan/tilt keys to move between items on the screen. When the menu item you desire is highlighted (blinking), do one of the following:
If a menu item has more than one option, press the OPEN key to cycle through the options to select the one you want.
If a menu item has only one option, press the OPEN key to select it.
Time and Date Set the current time and date. The time uses a 24-hour clock.
Time Display ON - Displays the time on the main monitor. OFF - The time is not shown on the main monitor.
TIP: Once you are in a menu, you can go to another menu by pressing the key(s) for that menu. Press and release the VIEW key to switch to the system setup menu. Enter a camera number and then press and release the CAM key to change to a camera menu. Press and hold the SEQ and LIVE/VCR keys to switch to the sequence and record menus.
TIP: In any menu you can scroll the options forward by pressing the OPEN key or scroll backward by pressing the CLOSE key.
Figure 3. Basic System Setup Menu
2/6/8 Hr 2/6/8 Hr
MAIN MONITOR VIDEO
RESET ACTIVITY DETECTION ALL CH TO
*2,6,or 8 Hr 120 Hr 12 Hr 168 Hr 16 Hr 180 Hr 18 Hr 240 Hr 24 Hr 360 Hr 48 Hr 480 Hr 72 Hr 600 Hr 84 Hr 720 Hr 96 Hr 960 Hr
HIGH RESOLUTION REDUCED FLICKER
MAIN MONITOR DISPLAY HIGH RESOLUTION
**
* 2/6/8 HR FOR NTSC/EIA MODEL MULTIPLEXERS, 3 HR FOR PAL/CCIR MODELS. REMAINING RECORD SPEEDS DEPEND UPON VCR MODEL. ** NOT SHOWN ON DUPLEX MONOCHROME MODELS OR SIMPLEX MULTIPLEXERS
**
Pelco Manual C581M-B (1/04) 21
Title Display (Duplex Multiplexer) ON - Displays camera titles and the word LIVE or VCR on the main monitor. OFF - Camera titles and the word LIVE or VCR are not shown on the main monitor.
Title Display (Simplex Multiplexer) ON - Displays camera titles on the main monitor. OFF - Camera titles are not shown on the main monitor.
Record Speeds Sets the speed at which the VCR normally records video and the speed at which it records when there is an alarm(s). Setting the speeds in the System Setup menu also sets the speeds in the Record Setup and Custom VCR Setup menus.
Main Monitor Video (Duplex Multiplexer Color Models Only) Composite is standard video on coaxial cable. SVHS is higher resolution video on a special cable.
Main Monitor Display The options are High Resolution or Reduced Flicker. Reduced Flicker can be selected when there is flickering on the monitor screen, such as from a neon light. This problem is more visible to the eye in PAL format multiplexers.
GLOBAL SETUPS
Video Terminations These settings set the terminations for all video inputs. To set individual inputs, refer to the Camera Setup section.
Set to 75 OHM when equipment is connected only to the video IN connectors. There must be no equipment connected to the video OUT connectors.
Set to LOOP HI-Z when equipment is connected to the video OUT (looping) connectors. For every channel that has equipment connected to the video IN connector, there must be equipment connected to the video OUT connector. Do not use this global setting if any channel has equipment connected to a video input but no equipment connected to the video output. Equipment connected to the looping connectors must be terminated at 75 ohms.
NO CHANGE - This is a pass-through selection in case you unintentionally hit the OPEN key. This is not an undo key.
Alarm Inputs Normally closed operation = current flow = alarm switch or relay closed. Normally open operation = no current flow = alarm switch or relay open.
Dwell Rates Sets the sequence dwell rate for all cameras. To set individual dwell rates for cameras, refer to the Sequence Setup section.
Activity Detection ENABLED/DISABLED - Turns activity detection on or off for all video inputs. To set individual inputs, refer to the Camera Setup section.
NO CHANGE - This is a pass-through selection in case you unintentionally hit the OPEN key. This is not an undo key.
5. When you have completed all the changes you want to make, go to EXIT or ADVANCED SETUP.
6. Press the OPEN key to exit the programming mode or to go to the advanced system setup menu.
When HELP is highlighted, you may press the OPEN key to display a help screen that will tell you which keys to press to configure specific options.
NOTE: Title Display shows a maximum of 12 characters in all modes except 16-camera display, in which only 9 char- acters are shown.
22 Pelco Manual C581M-B (1/04)
ADVANCED SYSTEM SETUP (View Key) To program the advanced main system parameters:
1. Press the MAIN MONITOR key.
2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
3. Press the VIEW key for approximately three seconds. The basic System Setup menu appears.
4. The currently selected menu item blinks. Use the pan/tilt keys to highlight ADVANCED SETUP.
5. Press the OPEN key. The Advanced System Setup menu appears.
6. Use the pan/tilt keys to move between items on the screen. When the menu item you desire is highlighted (blinking), press the OPEN key to cycle through the options.
Date Format Sets the format for displaying the date on the main monitor.
Password Enables or disables password control to access programming menus.
Front Panel Control Enables or disables the front panel buttons to operate the multiplexer. In either mode you can access programming menus. Has no effect on the keyboard.
Main Monitor Display Select ALARMS, ACTIVITY, or ALARMS/ACTIVITY if you want the main monitor to switch to cameras that have alarms or activity detection. If you are using the main monitor for normal video and you do not want alarms or activity detection to override what you are observing, select NONE.
Figure 4. Advanced System Setup Menu
ALL COLOR* COLOR & B/W RESERVED
DATE FORMAT MM-DD-YY PASSWORD DISABLED FRONT PANEL CONTROL ENABLED
MAIN MONITOR DISPLAY RESPONDS TO NONE
SPOT MONITOR DISPLAY SEQUENCE RESPONDS TO ALARMS
AUX MONITOR DISPLAY BLANK RESPONDS TO ACTIVITY
CAMERA TYPES ALL COLOR
UNIT ID 001 COMM. TYPE MASTER (KBD-T/D)
RELAY OUTPUT ALARM
MASTER (KBD-T/D)** (1) SLAVE (2)
001240
SEQUENCE BLANK TRACK MAIN
* ALL B/W SHOWN ON MONOCHROME MODELS. (1) SIMPLEX DEFAULT SETTING ** MUST BE SET IN THIS MODE FROM THE FRONT PANEL OF THE (2) DUPLEX DEFAULT SETTING
MULTIPLEXER TO PROGRAM THE MULTIPLEXER FROM THE KEYBOARD. *** DUPLEX MULTIPLEXER ONLY; NOT ON SIMPLEX
BLANK CAM 1
CAM 16 SEQUENCE
*** ***
Pelco Manual C581M-B (1/04) 23
Spot Monitor Display If you want the spot monitor to switch to cameras that have alarms or activity detection, select BLANK, SEQUENCE, or TRACK MAIN, then under RESPONDS TO select ALARMS, ACTIVITY, or ALARMS/ACTIVITY. If you are using the spot monitor for normal video and you do not want alarms or activity detection to override what you are observing, select NONE.
BLANK - Allows you to view an individual camera, but you cannot run a sequence. An alarm or activity detection will override the camera you are viewing. When the alarm or activity detection goes away, the screen will return to the camera you were viewing.
SEQUENCE - Allows you to view an individual camera or run a sequence. An alarm or activity detection will override what you are observing. When the alarm or activity detection goes away, the screen will return to the camera or sequence you were viewing.
TRACK MAIN - The spot monitor will follow the camera switching that occurs on the main monitor. This feature is used only when a KBD4002 keyboard is connected to the multiplexer for controlling moveable cameras. This mode provides an easy method of simplifying P/T/Z control in single-monitor applications. The operator does not have to switch to SPOT to gain P/T/Z control and there is no separate control of the spot monitor when in this mode. However, to do presets and patterns, switch to SPOT.
Aux Monitor Display (Duplex Multiplexer Only) Select ALARMS, ACTIVITY, or ALARMS OR ACTIVITY if you want the auxiliary monitor to show cameras with alarms or activity detection. If you are using the auxiliary monitor to sequence all cameras and you do not want alarms or activity detection to override the sequence, select NONE.
BLANK - This means the screen will remain blank unless there is an alarm or activity detection.
SEQUENCE - This means the monitor will sequence all cameras unless there is an alarm or activity detection.
CAM 1 through CAM 16 - This means the monitor will display the selected camera unless there is an alarm or activity detection.
Camera Types The COLOR & B/W setting allows the multiplexer to adapt to the combination of both color and monochrome video signals. The switching speed of the multiplexer is not as fast when it has to change formats between monochrome and color cameras. For duplex monochrome models, you will not receive color from a color camera except on the SPOT or AUX monitor displays. For simplex monochrome models, you will not receive color from a color camera except in RECORD mode.
The RESERVED setting can improve performance when using cameras with non-standard sync or poor video quality.
Unit ID This is the address of the multiplexer. If your system has more than one multiplexer, each multiplexer must have its own address. This must be set at the multiplexer, not at the keyboard.
Comm.Type In the polled communication mode (switch 4 OFF), one multiplexer (any one) must be the master. Only one multiplexer can be the master. All other multiplexers must be slaves. The master multiplexer communicates with the slave multiplexers.
In the non-polled communication mode (switch 4 ON), all multiplexers must be slaves.
The default is SLAVE for duplex multiplexers and MASTER (KBD T/D) for simplex multiplexers.
CAUTION: When programming the MX4000
Multiplexer from the KBD4002 Keyboard, DO NOT ATTEMPT TO CHANGE THE UNIT ID. Changing the unit ID from the keyboard will interrupt the keyboard communications to the multiplexer, resulting in erratic multiplexer operation. Refer to the Troubleshooting section, in this manual to correct the situation.
24 Pelco Manual C581M-B (1/04)
Relay Output Operates the relay on the back of the multiplexer. The relay is used to change the VCR to its alarm recording speed. In the alarms mode, an alarm signal is produced when a remote switch opens or closes a ground in the multiplexer; for example, if a switch is on a door and the door is opened. In the activity mode, the multiplexer continually monitors select camera inputs for motion. When motion is detected, the multiplexer increases the frequency with which that camera(s) is shown and recorded. Activity detection is most effective when only a few cameras are showing activity (refer to the Camera Setup section).
7. When you have completed all the changes you want to make, go to EXIT or BASIC SETUP.
8. Press the OPEN key to exit the programming mode or to go to the basic system setup menu.
When HELP is highlighted, you may press the OPEN key to display a help screen that will tell you which keys to press to configure specific options.
RECORD SETUP (Live/VCR Key) To program the VCR recording parameters:
1. Press the MAIN MONITOR key.
2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
3. Press the LIVE/VCR key for approximately three seconds. Type the password, if requested. The Record Setup menu appears. The currently selected menu item blinks.
4. Use the pan/tilt keys to move between items on the screen. When the menu item you desire is highlighted (blinking), press the OPEN key to cycle through the options to select the one you want.
Record Speeds Sets the speed at which the VCR normally records video and the speed at which it records when there is an alarm(s). Setting the speeds in the Record Setup menu also sets the speeds in the System Setup and Custom VCR Setup menus.
VCR Type (See Table D) If your VCR is not listed among the options, do either of the following:
Select UNIVERSAL. In the recording speed menu item at the top of the screen, select an option that your VCR will support.
Select CUSTOM. Then go to CONFIGURE CUSTOM VCR and press the OPEN key to go to the Custom VCR Setup menu. The switch interval can be changed only while in this setting.
VCR Video Format This feature is not available on monochrome multiplexers. Composite is standard video on a coaxial cable. SVHS is higher resolution video on a special cable.
VCR Switch Pulse ENABLED means the multiplexer waits for a head switching pulse from the VCR. If the multiplexer does not get a pulse from the VCR (because of a broken wire or the VCR does not give a pulse in some modes), it may appear that the multiplexer is not working properly.
DISABLED means the VCR head switching pulse is not used.
Alarm Handling Determines how alarms are recorded and for how long.
Configure Custom VCR Press the OPEN key to get to the CUSTOM VCR SETUP menu.
Playback Format Tapes made using Pelco, Robot, and DM multiplexers can be played.
Pelco Manual C581M-B (1/04) 25
Figure 5. Basic VCR Setting Menu
Table D. VCR Types
NTSC PAL
UNIVERSAL UNIVERSAL GYYR TLC1800 ASUTA TLVCR 251 GYYR 2100 ASUTSA TLVCR 964 GYYR 2100 HD MODE BURLE TC3910X JVC SR-L900U HITACHI VTL30E JVC SR-L901U HITACHI VT-L1000E JVC SR-9070U HITACHI VT-L2000E JVC BR-S925U JVC BR9060E MITSUBISHI HS7424U JVC BR-S920/925 MITSUBISHI HS7496U JVC SR-L900E MITSUBISHI HS5168U MITS. HS5300/5600 MITS. HS7168U NORM MITS. HS5424E MITS. HS7168U HD PANAS. AG6024/6124 PANASONIC AG-RT600 PANASONIC AG6720 PANASONIC AG6124 PANASONIC AG6730 PANASONIC AG 6730 PANASONIC AG6040 PELCO TLR2024 SANYO TLS900P PELCO TLR2096 SANYO TLS1000 PELCO TLR2168 NORM SANYO SRT-500P PELCO TLR2168HD SANYO TLS2000 SANYO SRT600 SONY SVT100P SANYO TLS924/972 SONY SVT5000P SANYO TLS2500/7000 CUSTOM TOSHIBA KV6300 TOSHIBA KV7024A TOSHIBA KV7168A TOSHIBA KV7960A TOSHIBA KV8168A CUSTOM
** **
ALARM DURATION 30 SECONDS 1 MINUTE 2 MINUTES 5 MINUTES 10 MINUTES 15 MINUTES
ENABLED DISABLED
*2,6,or 8 Hr 24 Hr 96 Hr 240 Hr 12 Hr 48 Hr 120 Hr 360 Hr 16 Hr 72 Hr 168 Hr 480 Hr 18 Hr 84 Hr 180 Hr 600 Hr 720 Hr 960 Hr
PELCO ROBOT DM
SEE TABLE D
* 2/6/8 HR FOR NTSC/EIA MODEL MULTIPLEXERS, 3 HOUR FOR PAL/CCIR MODELS. REMAINING RECORD SPEEDS DEPEND UPON VCR MODEL. ** NOT SHOWN ON MONOCHROME MODELS.
NORMAL REC. SPEED 2/6/8 Hr ALARM REC. SPEED 2/6/8 Hr
VCR SETUP
VCR TYPE UNIVERSAL VCR VIDEO FORMAT COMPOSITE VCR SWITCH PULSE DISABLED
ALARM HANDLING
RECORD ALARMS AS A PRIORTIY ALARM RECORD TIME ALARM DURATION
CONFIGURE CUSTOM VCR
PLAYBACK FORMAT PELCO
26 Pelco Manual C581M-B (1/04)
5. When you have completed all the changes you want to make, go to EXIT.
6. Press the OPEN key to exit the programming mode.
When HELP is highlighted, you may press the OPEN key to display a help screen that will tell you which keys to press to configure specific options.
CUSTOM VCR SETUP (Live/VCR Key) To program the advanced VCR parameters:
1. Press the MAIN MONITOR key.
2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
3. Press the LIVE/VCR key for approximately three seconds. The Record Setup menu appears. The currently selected menu item blinks.
4. Make sure the VCR Type in the Record Setup menu is set to CUSTOM.
5. Use the pan/tilt keys to highlight CONFIGURE CUSTOM VCR.
6. Press the OPEN key. The Custom VCR Setup menu appears.
7. Use the pan/tilt keys to move between items on the screen. When the menu item you desire is highlighted (blinking), press the OPEN key to cycle through the options.
Record Speeds Sets the speed at which the VCR normally records video and the speed at which it records when there is an alarm(s).
Setting the speeds in the Custom VCR Setup menu also sets the speeds in the System Setup and Record Setup menus.
Interval Interval is the number of fields recorded by the VCR before switching to the next camera.
8. When you have completed all the changes you want to make, go to EXIT or BACK.
9. Press the OPEN key to exit the programming mode or to return to the Record Setup menu.
When HELP is highlighted, you may press the OPEN key to display a help screen that will tell you which keys to press to configure specific options.
NOTE: For proper record- ing, the switching rate of the multiplexer must match that of the VCR. If they do not match, the VCR may skip frames or record duplicate frames.
Figure 6. Custom VCR Setup Menu
NORMAL RECORD SETUP
RECORD SPEED 2/6/8 Hr SWITCH INTERVAL 003
ALARM RECORD SETUP
RECORD SPEED 2/6/8 Hr SWITCH INTERVAL 003
EXIT BACK
003 TO 509 **
*2,6,or 8 Hr 120 Hr 12 Hr 168 Hr 16 Hr 180 Hr 18 Hr 240 Hr 24 Hr 360 Hr 48 Hr 480 Hr 72 Hr 600 Hr 84 Hr 720 Hr 96 Hr 960 Hr
*2/6/8 HR FOR NTSC/EIA MODEL MULTIPLEXERS, 3 HR FOR PAL/CCIR MODELS. REMAINING RECORD SPEEDS DEPEND UPON VCR MODEL.
** VCR TYPE IN RECORD SETUP MENU MUST BE SET TO CUSTOM IN ORDER TO MAKE SELECTIONS.
Pelco Manual C581M-B (1/04) 27
CAMERA SETUP (Number and CAM Keys) To program a camera input:
1. Press the MAIN MONITOR key.
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number keypad, enter the address number of the multiplexer (1-16 if the
keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
b. On the number keypad, enter the number of the camera, then press and hold the CAM key until the Camera menu appears.
Addressing Consecutively (Switch 7 ON) On the number keypad, enter the number of the camera, then press and hold the CAM key until the Camera menu appears. Refer to Table C for camera numbers.
3. A video insert appears that shows what the camera is viewing. This is useful to make sure you have selected the correct camera and to see what effect there is on the video when you select a menu option. The currently selected menu item blinks.
4. Use the pan/tilt keys to move between items on the screen. When the menu item you desire is highlighted (blinking), press the OPEN key to cycle through the options to select the one you want. Use the right pan key to advance to the next character position when titling a camera.
Video Termination Set to 75 OHM when equipment is connected only to the video IN connector.
Set to LOOP HI-Z when equipment is also connected to the video OUT (looping) connector. Equipment connected to the looping connector must be terminated at 75 ohms.
Alarm Input Normally closed operation = current flow = alarm switch or relay closed. Normally open operation = no current flow = alarm switch or relay open.
Figure 7. Basic Camera Menu
OPEN CLOSED DISABLED
VIDEO INPUT TERMINATION 75 OHM ALARM INPUT NORMALLY OPEN COAXITRON FORMAT EXTENDED
ACTIVITY DETECTION ENABLED SET DETECTION MASK
ENABLED DISABLED
* ONLY NINE CHARACTERS APPEAR WHEN IN THE 16-CAMERA DISPLAY. (1) SIMPLEX DEFAULT SETTING (2) DUPLEX DEFAULT SETTING
EXTENDED (1) OFF (2) STANDARD
ENTER UP TO 12* NUMBERS, LETTERS OR SYMBOLS
28 Pelco Manual C581M-B (1/04)
Coaxitron Format EXTENDED - Use when your system has moveable cameras controlled by 32-bit Coaxitron receivers, such as Esprit, Intercept, Spectra, and LRD41C21/LRD41C22 Series.
OFF - Use when your system has fixed cameras only.
STANDARD - Use when your system has moveable cameras controlled by 15-bit Coaxitron receivers, such as the CX9000 Series, the PT7700, and the ED25/27/28/29.
Activity Detection A camera can be set to respond or not to respond to motion. If enabled select SET DETECTION MASK to define what part of the cameras viewing field will be monitored for motion.
5. To program another camera, press the number key for that camera then press the CAM key. Repeat steps 2-4.
6. When you have completed all the changes you want to make, go to EXIT.
7. Press the OPEN key to exit the programming mode.
When HELP is highlighted, you may press the OPEN key to display a help screen that will tell you which keys to press to configure specific options.
NOTE: The Coaxitron format default setting is OFF for the duplex multiplexer and EX- TENDED for the simplex mul- tiplexer.
Pelco Manual C581M-B (1/04) 29
ACTIVITY DETECTION MASK SETUP Activity detection continually monitors selected camera inputs for motion. When motion is detected, the multiplexer increases the frequency with which that camera(s) is shown and recorded. Activity detection is most effective when only a few cameras are showing activity. As the number of cameras with activity increases, the slower the frequency at which they can be shown and recorded. If all 16 cameras show activity, there will be virtually no increase.
The activity detection mask selects that portion or portions of the cameras field of view that the multiplexer will monitor for motion. The entire grid is active on default.
To program an activity detection mask for a camera:
1. Press the MAIN MONITOR key.
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number keypad, enter the address number of the multiplexer (1-16 if the
keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
b. On the number keypad, enter the number of the camera, then press and hold the CAM key until the Camera menu appears.
Addressing Consecutively (Switch 7 ON) On the number keypad, enter the number of the camera, then press and hold the CAM key until the Camera menu appears. Refer to Table C for camera numbers.
3. The currently selected menu item blinks. Use the pan/tilt keys to highlight SET DETECTION MASK.
4. Press the OPEN key. The Activity Detection Mask appears. The currently selected menu item or activity box blinks.
5. Use the pan/tilt keys to move between menu items and activity boxes on the screen.
6. Highlight the sensitivity menu item. Press the OPEN key to select the sensitivity. The higher the sensitivity is, the less the amount of motion that will be needed to detect activity.
Figure 8. Activity Detection Mask
ACTIVITY DETECTION MED SENSITIVITY
SET ALL CLEAR ALL EXIT TEST
ACTIVITY BOX SET
ACTIVITY BOX CLEAR
LOW SENSITIVITY MED SENSITIVITY HIGH SENSITIVITY
30 Pelco Manual C581M-B (1/04)
7. Turn activity boxes on or off (by default, all activity boxes are on).
To turn on all activity boxes, use the pan/tilt keys to choose SET ALL. Press the OPEN key. All boxes will contain a symbol as shown in Figure 8. The multiplexer will monitor motion in those boxes.
To turn off all activity boxes, use the pan/tilt keys to choose CLEAR ALL. Press the OPEN key. All boxes will be blank.
To turn on or off an individual box, use the pan/tilt keys to select the box. Press OPEN key to toggle a box on or off.
Turn off activity boxes where you want motion ignored, such as blowing trees, high- ways, computer monitors, fluorescent lighting, and non-problem areas. An example of a non-problem area would be a camera focused on a bank vault entrance but ignoring tellers working nearby.
8. To test the activity detection, highlight TEST and press the OPEN key.
Create motion in front of the camera. Small black and white dashes will flash where motion is detected.
To exit the test mode, press the OPEN key to return to the mask.
9. If you did not like what you saw in the test mode, change the mask and test the activity detection again.
10. When you finish defining the activity detection mask, go to EXIT. Press the OPEN or CLOSE key to exit the programming mode.
11. If necessary, repeat steps 1-10 to program the activity detection mask for other cameras.
SEQUENCE SETUP (SEQ Key) Sequencing can be programmed in full screen, four-camera and nine-camera displays. The cameras will not sequence when operating the zoom function. The LED(s) above the camera button(s) on the multiplexer will illuminate to indicate which camera(s) is being displayed.
To program camera sequencing:
1. Press the MAIN MONITOR key.
2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
3. Press the SEQ key for approximately three seconds. Type the password, if requested. The Sequence menu appears. The currently selected menu item blinks.
4. Use the pan/tilt keys to move between items on the screen. When the menu item you desire is highlighted (blinking), press the OPEN key to cycle through the options to select the one you want.
5. When you have completed all the changes you want to make, go to EXIT.
6. Press the OPEN key to exit the programming mode.
When HELP is highlighted, you may press the OPEN key to display a help screen that will tell you which keys to press to configure specific options.
Pelco Manual C581M-B (1/04) 31
HELP MENU The Help menu is accessed from any other menu.
1. Use the pan/tilt keys in any menu to highlight HELP.
2. Press the OPEN key. The Help menu appears.
Figure 9. Camera Sequence Menu
Figure 10. Help Menu
GROUP QUAD (2x2) 1 04 2 04 3 04 4 04
NINE (3x3) 04 04
VCR/LIVE*
* SIMPLEX MULTIPLEXERS SHOW DISP/REC. PRESS THE LIVE/VCR KEY ON THE KEYBOARD.
BUTTON SETTING VCR SPEED & ALARM
QUICK SETUP
MONITOR SETUP
HELP
+/ - SINGLE PRESS MODIFY DOUBLE PRESS CHANGE EDIT DIRECTION
HOLD BUTTONS TO ENTER/EXIT THEIR ASSOCIATED MENU USE ARROWS TO NAVIGATE
32 Pelco Manual C581M-B (1/04)
MULTIPLE CAMERA DISPLAY SETUP
The multiple camera display formats may be configured using the keyboard. The LEDs above the camera buttons on the multiplexer will illuminate to indicate which cameras are being displayed.
PROGRAMMING THE PICTURE-IN-PICTURE DISPLAY ( Key) The on-screen location and size of the picture-in-picture (PIP) display are programmable. PIP is not available in duplex VCR playback or in simplex RECORD mode.
To program the PIP display:
1. Press the MAIN MONITOR key.
2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
3. Press the key.
4. Press the key for approximately three seconds until the message PROGRAM PIP SIZE appears.
5. Use the pan/tilt keys to increase or decrease the PIP display size.
6. Press the key for approximately three seconds until the message PROGRAM PIP POSITION appears.
7. Use the pan/tilt keys to move the PIP display location.
8. Press and hold the key to exit the PIP programming menu.
PROGRAMMING THE 4-CAMERA DISPLAY ( Key) You can program four groups of four cameras each. Each of the four groups can be pro-
grammed to include any four cameras. is not available in simplex RECORD mode.
To program the four-camera displays:
1. Press the MAIN MONITOR key.
2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
3. Press the key to call up a four-camera display. If necessary, press the key again to advance to the four-camera group that you wish to configure.
4. Press the key for approximately three seconds. A bar will appear in the first camera location of the four-camera display, indicating that you are in the programming mode.
5. Use the pan/tilt keys to move to each camera location in the four-camera display.
6. When the camera location that you desire is highlighted, choose the new camera by pressing the number key for the desired camera and then pressing the CAM key.
7. To exit the programming mode, use the pan/tilt keys to move the bar off the screen.
8. If necessary, repeat steps 1-5 to program another group.
Pelco Manual C581M-B (1/04) 33
PROGRAMMING THE 9-CAMERA DISPLAY ( Key) You can program two groups of nine cameras each. Both groups can be programmed to include any nine cameras. is not available in simplex RECORD mode.
To program the nine-camera displays:
1. Press the MAIN MONITOR key.
2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
3. Press the key to call up a nine-camera display. If necessary, press the key again to advance to the other nine-camera group.
4. Press the key for approximately three seconds. A bar will appear in the first camera location of the nine-camera display, indicating that you are in the programming mode.
5. Use the pan/tilt keys to move to each camera location in the nine-camera display.
6. When the camera location that you desire is highlighted, choose the new camera by pressing the number key for the desired camera and then pressing the CAM key.
7. To exit the programming mode, use the pan/tilt keys to move the bar off the screen.
8. If necessary, repeat steps 1-5 to program the second group.
PROGRAMMING THE 16-CAMERA DISPLAY ( Key) is not available in simplex RECORD mode.
To program the 16-camera display:
1. Press the MAIN MONITOR key.
2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key.
3. Press the key to call up the 16-camera display.
4. Press the key for approximately three seconds. A bar will appear in the first camera location of the 16-camera display, indicating that you are in the programming mode.
5. Use the pan/tilt keys to move to each camera location in the 16-camera display.
6. When the camera location that you desire is highlighted, choose the new camera by pressing the number key for the desired camera and then pressing the CAM key.
7. To exit the programming mode, use the pan/tilt keys to move the bar off the screen.
34 Pelco Manual C581M-B (1/04)
PROGRAMMING MENU DEFAULTS
Table E. Programming Menu Defaults
Menu Item Default
System Setup Time Display On Title Display On Normal Record Speed 2/6/8 Hr (NTSC/EIA)
3 Hr (PAL/CCIR) Alarm Record Speed 2/6/8 Hr (NTSC/EIA)
3 Hr (PAL/CCIR) Main Monitor Video (Duplex Only) Composite Main Monitor Display High Resolution Reset All Video Terminations To 75 Ohm Reset All Alarm Inputs to Normally Opened Reset All Seq Dwell Rates To 02 Reset Activity Detection All Ch To Enabled
Advanced System Date Format MM-DD-YY (NTSC/EIA) Setup DD-MM-YY (PAL/CCIR)
Password Disabled System Password 3916 Front Panel Control Enabled Main Monitor Display Responds To None Spot Monitor Display Sequence Responds To Alarms Aux Monitor Display (Duplex Only) Blank Responds To (Duplex Only) Activity Camera Types All Color (All B/W for monochrome) Unit ID 001 Comm. Type Master (KBD-T/D) (Simplex)
Slave (Duplex) Relay Output Alarm
Record Setup Normal Rec. Speed 2/6/8 Hr (NTSC/EIA) 3 Hr (PAL/CCIR)
Alarm Rec. Speed 2/6/8 Hr (NTSC/EIA) 3 Hr (PAL/CCIR)
VCR Type Universal VCR Video Format Composite VCR Switch Pulse Disabled Record Alarms As A Priority Alarm Record Time Alarm Duration Playback Format Pelco
Custom VCR Normal Record Speed 2/6/8 Hr (NTSC/EIA) Setup 3 Hr (PAL/CCIR)
Normal Switch Interval 003 Alarm Record Speed 2/6/8 Hr (NTSC/EIA)
3 Hr (PAL/CCIR) Alarm Switch Speed 003
Camera Title Camera Number Video Input Termination 75 Ohm Alarm Input Normally Open Coaxitron Format Extended (Simplex)
Off (Duplex) Activity Detection Enabled
Activity Detection Sensitivity Med Activity Boxes Set All
Sequence Individual Camera Dwell Time 02 Quad (2x2) Dwell Time 04 Nine (3x3) Dwell Time 04
Pelco Manual C581M-B (1/04) 35
PROGRAMMING A PRESET
1. Press the MAIN or SPOT MONITOR key. The green LED over the MAIN or SPOT key lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in the Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup section).
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the multiplexer (1-16 if the
keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
3. Position the camera using the pan/tilt and lens keys.
4. On the number keypad press the number of the preset, then hold down the PRESET key for five seconds.
PROGRAMMING A PATTERN
1. Press the MAIN or SPOT MONITOR key. The green LED over the MAIN or SPOT key lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in the Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup section).
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the multiplexer (1-16 if the
keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.
b. On the number keypad press the number of the camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON) On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.
3. On the number pad, press a number key for the pattern number. Example: If you are programming pattern 1 press the number 1 key. Then hold down the PATTERN key until the message PROGRAMMING PATTERN appears on the screen.
4. Move the camera through the pattern using the pan/tilt and lens keys.
5. To stop programming the pattern, repress the number key for the pattern followed by the PATTERN key. Example: Press number 1 and then the PATTERN key if you are programming pattern 1. The message PROGRAMMING PATTERN disappears.
NOTE: The LEDs above the camera buttons on the multiplexer will illuminate to indicate which cameras are being displayed.
NOTE: Refer to your dome or pan and tilt system manual for information on the number of available patterns and pattern durations.
36 Pelco Manual C581M-B (1/04)
TROUBLESHOOTING
If you have difficulty operating your system, run through the following checklist to see if you can solve the problem.
1. Are the keyboard switches set properly?
2. Is the equipment wired properly?
3. Are the menu options in the multiplexer(s) and server set properly?
4. Has the multiplexer been set to the correct mode for live video or tape playback?
5. Only the main monitor displays multiple screen images. The spot monitor displays full screen views only.
6. Patterns, presets, and auxiliaries will work in both MAIN and SPOT MONITOR. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in the Advanced System Setup menu must be set to TRACK MAIN.
7. The auxiliary monitor (duplex multiplexer only) is controlled by programming. You cannot control it from the keyboard or from the front panel of the multiplexer.
8. Tape playback can be done only on the main monitor (in VCR mode).
9. Moveable cameras must be Coaxitron compatible and the proper Coaxitron format se- lected in the Camera menu of the multiplexer. If the proper format is not selected, the camera will either not move or have sluggish control.
10. Moveable cameras can be operated with the pan/tilt keys only if SPOT MONITOR is chosen or if the spot monitor is programmed to track the main monitor. The camera will move on the main monitor if the same camera is being shown on both the main and spot monitors.
11. The position of switch 7 on the keyboard determines how you call cameras. If the switch is ON, all cameras are addressed consecutively. Do not count just the cameras installed. Count 16 camera inputs per multiplexer, even if a multiplexer has only 9 inputs. The first input of multiplexer 1 is always camera 1, the first input of multiplexer 2 is always camera 17, the second input of multiplexer 3 is always camera 34.
If the switch is OFF, cameras are addressed in groups 9 or 16 according to the address of the multiplexer. Select a multiplexer (for example, number 3), then choose a camera (1-9 or 1-16).
12. In the polled communication mode (switch 4 OFF), if you have one multiplexer, it must be the master. If you have more than one multiplexer, one of them (any one) must be the master and all the others slaves. In the non-polled mode (switch 4 ON), all multiplexers must be slaves. Refer to the Advanced System Setup menu of the multiplexer.
13. If you have more than one multiplexer, they must have different addresses (Advanced System Setup menu of multiplexer).
14. If you have a server, the address of the multiplexer must correspond to the input it is connected to on the server. For example, if the multiplexer goes to input 4 on the server, the multiplexer must be address 4.
15. If you have a server, each keyboard must have its own address.
16. If you have a server, each keyboard controls its corresponding monitor(s). In the SINGLE mode, keyboard 1 controls monitor 1, keyboard 2 controls monitor 2, etc. In the PAIRED mode, keyboard 1 controls monitor 1 (main) and monitor 2 (spot), and keyboard 3 controls monitor 3 (main) and monitor 4 (spot). In the paired mode, keyboards 2 and 4 are not used.
17. If you have a server and cannot change between full screen and multiple screen views on the main monitor, check the MAIN MONITOR CONTROL setting in the Monitor menu of the server.
Pelco Manual C581M-B (1/04) 37
18. If the UNIT ID, in the ADVANCED SYSTEM SETUP menu, is inadvertently changed at the keyboard resulting in an uncontrollable sequencing of unit ID numbers and loss of keyboard control:
a. Go to the multiplexer and press the down arrow button. The sequencing should stop. Exit the menu, then return to the ADVANCED SYSTEM SETUP menu and change the UNIT ID back to 001. Continue normal programming from the key- board.
OR
b. If the multiplexer is remotely located away from the keyboard, wait until the numbers sequence to the correct multiplexer unit ID number and immediately press any pan/tilt key. The sequencing should stop. Continue normal program- ming from the keyboard.
SPECIFICATIONS
ELECTRICAL
Input Voltage: 12 VAC or 12 VDC
Power Consumption: 5 watts
KEYBOARD COMMUNICATION
Keyboard Interface: RS-485 (25-foot flat cable supplied)
Connector Type: RJ-45 8-pin modular (female)
MECHANICAL
Keyboard Keypad: Mechanical
Digital Display: Two red seven-segment LEDs
Main/Spot Monitor Indicators: Two green LEDs
GENERAL
Ambient Operating Temperature: 20 to 120F (-7 to 49C)
Humidity: 10% - 90% non-condensing
Dimensions: 8.125 (W) x 7.125 (L) x 2.25 (H) inches (20.64 x 18.10 x 5.72 cm)
Weight: 2.1 lb (0.97 kg)
Shipping Weight: 3 lb (1.35 kg)
Design and product specifications subject to change without notice.
38 Pelco Manual C581M-B (1/04)
Pelco Manual C581M-B (1/04) 39
REVISION HISTORY Manual # Date Comments C581M 8/99 Original version. C581M-A 9/03 Added Regulatory Notices section and changed power specification. C581M-B 1/04 Revised per ECO #03-9291, software upgrade to increase the number of programmable patterns.
Pelco, the Pelco Logo, Camclosure, Coaxitron, Esprit, Genex, Intercept, Legacy, and Spectra are registered trademarks of Pelco. Copyright 2004, Pelco. All rights reserved. Endura and ExSite are trademarks of Pelco.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
Five years on FT/FR8000 Series ber optic products.
Three years on Genex Series products (multiplexers, server, and keyboard).
Three years on Camclosure and xed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a ve-year warranty.
Two years on standard motorized or xed focal length lenses.
Two years on Legacy, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series xed dome products.
Two years on Spectra, Esprit, ExSite, and PS20 scanners, including when used in continuous motion applications.
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura Series distributed network-based video products.
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specic use or application made of the Products. Pelcos liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of prot and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specic legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: 1. Model and serial number 2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number 3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identied with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to: Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to: Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to: Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933
Worldwide Headquarters 3500 Pelco Way
<Related manuals for Pelco KBD4002 C581M-B Keyboard Operation Manual
en
en
en
en
en
en
Manualsnet FAQs
If you want to find out how the KBD4002 Pelco works, you can view and download the Pelco KBD4002 C581M-B Keyboard Operation Manual on the Manualsnet website.
Yes, we have the Operation Manual for Pelco KBD4002 as well as other Pelco manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Operation Manual should include all the details that are needed to use a Pelco KBD4002. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Pelco KBD4002 C581M-B Keyboard Operation Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Pelco KBD4002 C581M-B Keyboard Operation Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Pelco KBD4002 C581M-B Keyboard Operation Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Pelco KBD4002 C581M-B Keyboard Operation Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Pelco KBD4002 C581M-B Keyboard Operation Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.