Pelco NET5501-I C5649M-A Encoder Quick Start Guide PDF

1 of 12
1 of 12

Summary of Content for Pelco NET5501-I C5649M-A Encoder Quick Start Guide PDF

C5649M-A (10/14)

NET5501-I VIDEO ENCODER Quick Start Guide

IMportAnt SAfety InStruCtIonS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or

sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases shall be placed on the apparatus.

16. WArnInG : To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 17. Installation should be done only by qualified personnel and conform to all local codes. 18. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor

use only and it must not be installed where exposed to rain and moisture. 19. Use only installation methods and materials capable of supporting four times the maximum specified load. 20. A readily accessible disconnect device shall be incorporated in the building installation wiring. 21. A CCC approved power cord must be used to power this equipment when used in China.

CAutIon

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

WArnInG : This product is sensitive to Electrostatic Discharge (ESD). To avoid ESD damage to this product, use ESD safe practices during installation. Before touching, adjusting or handling this product, correctly attach an ESD wrist strap to your wrist and appropriately discharge your body and tools. For more information about ESD control and safe handling practices of electronics, please refer to ANSI/ESD S20.20- 1999 or contact the Electrostatic Discharge Association (www.esda.org).

2 | English

IMportAnt notICeS

reGuLAtory notICeS

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

rADIo AnD teLeVISIon InterferenCe This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commissions rules.

CAn ICeS-3(A)/nMB-3(A)

LeGAL notICe [Audio notice]

SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY REQUIRE, AMONG OTHER THINGS, EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS. YOU ARE SOLELY RESPONSIBLE FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS AND FOR STRICT ADHERENCE TO ANY/ALL RIGHTS OF PRIVACY AND PERSONALTY. USE OF THIS EQUIPMENT AND/OR SOFTWARE FOR ILLEGAL SURVEILLANCE OR MONITORING SHALL BE DEEMED UNAUTHORIZED USE IN VIOLATION OF THE END USER SOFTWARE AGREEMENT AND RESULT IN THE IMMEDIATE TERMINATION OF YOUR LICENSE RIGHTS THEREUNDER.

VIDeo QuALIty CAutIon

frAMe rAte notICe reGArDInG uSer SeLeCteD optIonS Pelco systems are capable of providing high quality video for both live viewing and playback. However, the systems can be used in lower quality modes, which can degrade picture quality, to allow for a slower rate of data transfer and to reduce the amount of video data stored. The picture quality can be degraded by either lowering the resolution, reducing the picture rate, or both. A picture degraded by having a reduced resolution may result in an image that is less clear or even indiscernible. A picture degraded by reducing the picture rate has fewer frames per second, which can result in images that appear to jump or move more quickly than normal during playback. Lower frame rates may result in a key event not being recorded by the system.

Judgment as to the suitability of the products for users' purposes is solely the users' responsibility. Users shall determine the suitability of the products for their own intended application, picture rate and picture quality. In the event users intend to use the video for evidentiary purposes in a judicial proceeding or otherwise, users should consult with their attorney regarding any particular requirements for such use.

open SourCe SoftWAre

This product includes certain open source or other software originated from third parties that is subject to the GNU General Public License (GPL), GNU Library/Lesser General Public License (LGPL) and different and/or additional copyright licenses, disclaimers, and notices.

The exact terms of GPL, LGPL, and some other licenses are provided to you with this product. Please refer to the exact terms of the GPL and LGPL at http://www.fsf.org (Free Software Foundation) or http://www.opensource.org (Open Source Initiative) regarding your rights under said license. You may obtain a complete corresponding machine-readable copy of the source code of such software under the GPL or LGPL by sending your request to digitalsupport@pelco.com; the subject line should read Source Code Request. You will then receive an email with a link for you to download the source code.

This offer is valid for a period of three (3) years from the date of the distribution of this product by Pelco.

English| 3

CCC poWer CorD StAteMent

Models shipped to China do not include power cords.

note : A CCC approved power cord must be used to power the equipment when used in China.

Korean Class A eMC

(A) , .

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

eSD WArnInG

WArnInG: This product is sensitive to Electrostatic Discharge (ESD). To avoid ESD damage to this product, use ESD safe practices during installation. Before touching, adjusting or handling this product, correctly attach an ESD wrist strap to your wrist and appropriately discharge your body and tools. For more information about ESD control and safe handling practices of electronics, please refer to ANSI/ESD S20.20-1999 or contact the Electrostatic Discharge Association (www.esda.org).

Warranty

For information about Pelcos product warranty and thereto related information, refer to www.pelco.com/warranty.

netWorK topoLoGy StAteMent

IMportAnt note. pLeASe reAD. The network implementation is shown as a general representation only and is not intended to show a detailed network topology. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the system as illustrated. Please contact your local Pelco representative to discuss your specific requirements.

LeGAL notICe (AuDIo notICe)

J Improper use of audio/visual recording equipment may subject you to civil and criminal penalties. Applicable laws regarding the use of such capabilities vary between jurisdictions and may require, among other things, express written consent from the recorded subjects. You are solely responsible for insuring strict compliance with such laws and for strict adherence to any/all right of privacy and personalty.

4 | English

IntroDuCtIon

The NET5501-I video encoder is a network-based channel encoder with a built-in, Web-based viewer for live streaming to a standard Web browser (Microsoft Internet Explorer, Chrome, Safari or Mozilla Firefox). The encoder is built upon open standards and is part of an Endura system for recording, managing, administering, and viewing video streams.

The encoder supports H.264 and MJPEG compression. It can generate two independently configurable H.264 streams, each up to D1 resolution (720 x 480 for NTSC, 720 x 576 for PAL) and 30/25 images per second (ips) in addition to an MJPEG stream for Web viewing.

The NET5501-I can be configured for one video channel. When an alarm event is triggered, the unit can send a message to an operator.

The unit also supports motion detection for the video channel. You can configure one motion zone, with its own independent sensitivity and threshold settings. When the NET5501-I detects activity in any of these areas, it can trigger an alarm event.

The NET5501-I supports control of remote peripherals such as pan/tilt/zoom (PTZ) cameras by way of D-Protocol, P-Protocol, and Coaxitron protocols.

Getting Started

Before installing your device, thoroughly familiarize yourself with the information in the installation section of this manual.

noteS

~ Pelco recommends connecting the device to a network that uses a Dynamic Host Configuration Protocol (DHCP) server to address devices.

~ Do not use a network hub when configuring the network settings for the device. ~ To ensure secure access, place the device behind a firewall when it is connected to a network.

SuppLIeD pArtS LISt

4-Pin Terminal Block (1ea) / Screw (4ea) for Wall bracket binding 2 plus 2 spare / Anchor (2ea) for Wall mounting / Screw (2ea) for Wall mounting / Wall Mount Bracket (1ea)

English| 5

front pAneL DeSCrIptIon

no. name Description

a

RX+/RX- RS-422 RX Data line

J Disabled in RS-485 mode.

TX+/TX- RS-422/RS-485 Data line

b

1

1

A NO COM Tx+ Rx+

NC Tx- Rx-

Video input BNC terminal.

c Top Panel Indicators

Displays power On/Off status. It glows blue when the unit has power.

Displays network status (connection and speed).

off : The unit is not connected to the network. Solid amber : The unit is not connected to the network using the 100 Mbps standard. Solid red : The unit is not connected to the network using the 10 Mbps standard. Solid green : The unit is not connected to the network using the 1 Gbps standard.

A blinking light indicates network activity corresponding to the speed based on the color.

Displays camera connection status.

not Lit : A camera has not been connected yet. Green : Camera video is present at the video in connector. red : Video is no longer present, the camera is not functioning properly.

Displays unit status.

Green : The unit is functioning normally. red : The unit is in an error condition.

ptZ pin Assignments

Label Lead Label Lead

RX- RS-422 Data RX- TX- RS-422 Data TX-

RX+ RS-422 Data RX+ TX+ RS-422 Data TX+

a b c

6 | English

reAr pAneL DeSCrIptIon

no. name Description

a

1

1

A NO COM Tx+ Rx+

NC Tx- Rx-

Press this switch to reset device to the factory default. If you perform the factory reset, all your settings to device will be lost.

b PoE Connects to the network and supplies power through Ethernet cable.

English| 7

POE

a b

WALL BrACKet InStALLAtIon

1. Align the product with the bracket holes. Insert and tighten the provided screws to attach the product to the bracket.

2. Use drill bit of 5 mm (0.20 in.) diameter and drill on the marked positions, drill to have 3 cm (1.18 in.) deep holes. Clean the holes after drilling.

3. Insert an anchor for each hole. Fully insert anchors by lightly hammering the anchor head with a hammer/rubber hammer.

4. Place the wall-mount bracket on the desired wall and fasten screws through the 2 holes using a screwdriver.

J Use the provided screws when installing the bracket on the product. If you use any other screws, it may cause damage to the product.

8 | English

ACCeSSInG the enCoDer AnD AttACheD CAMerAS

The first time you access the camera, the live video page appears. By default, you are viewing the video as a public user and only have access to the single stream live view.

If, for security purposes, users should not be allowed to view video without first logging on to the camera, change the permissions for public users.

Logging In

Entering the IP address of the camera as a URL into the web browser will immediately bring up the Live Mode screen if the encoder is not setup to require authentication (Open Authentication option). If the camera is setup to require authentication, then the user will be prompted for a Username and Password before being able to see the live video feed.

1. Click on the live screen.

2. Enter your and .

Default username : admin, Password : admin

3. Click the button.

The Open Authentication option is configured on the Settings > Users > General Settings screen.

English| 9

Live Screen overview

Live Mode Screen Components

no. name Description

a Channel Name Displays the name assigned to the channel selected.

b Multi-Function Image Button

$ Tilt Up

% Tilt Down

+ Pan Right

_ Pan Left

Home Preset

c Control the Zoom Activates Zoom in (-) / Zoom out (+) features.

d Control the Focus Activates Near (-) / Far (+) features.

e Control the Iris Adjusts the camera brightness.

f Move to Presets Moves to the preset selected.

g Pattern Activates the pattern selected.

h Stream Selection Selects the viewable video stream that displays in live view (Primary, Secondary, QuickView) and selects unicast or multicast and throttle settings.

It will not be presented to users who are designated as Viewers.

i View the Selected Tab Composed of Live, Settings, Help, and Logout settings menus.

10 | English

h

k

j i

l m

a

f

g

b

c d e

no. name Description

j Maximize Viewing Area Scales the image to the full size of the browser. To resize the video pane to normal view, click the Show Toolbar button in the upper-right corner of the window.

k Take a Snapshot Captures the image displayed in the video pane and saves it as a JPEG file.

l Open Stream in New Window

Opens the video in a scalable, independent window. Opening the video in a separate window allows you to view the video while other applications are running. This window can be minimized, maximized, or closed using the title bar buttons of the active window. The window can also be resized by dragging a corner of the window.

m Pan/Tilt/Zoom

Control the encoder and the pan (left/right) and tilt (up/down) of the connected camera by dragging the mouse. Also, zoom using the scroll wheel on the mouse.

These icons are always available when using the Pelco Media Player. If you are using QuickTime, PTZ overlay is only available with PMP player.

English| 11

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2012/19/EU of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

reVISIon hIStory Manual # Date Comments C5649M C5649M-A

07/14 10/14

Original version Changed power consumption values. Changed the model name(Network Video Encoders ; Video Encoder)

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the prope

Manualsnet FAQs

If you want to find out how the NET5501-I Pelco works, you can view and download the Pelco NET5501-I C5649M-A Encoder Quick Start Guide on the Manualsnet website.

Yes, we have the Quick Start Guide for Pelco NET5501-I as well as other Pelco manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Guide should include all the details that are needed to use a Pelco NET5501-I. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Pelco NET5501-I C5649M-A Encoder Quick Start Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Pelco NET5501-I C5649M-A Encoder Quick Start Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Pelco NET5501-I C5649M-A Encoder Quick Start Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Pelco NET5501-I C5649M-A Encoder Quick Start Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Pelco NET5501-I C5649M-A Encoder Quick Start Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.