16 16 System Organization 16 Mounting in a rack 18 Desktop Installation 18 Factory Default 19 Connecting to an External Device
web viewer
27 27 What is the Web Viewer? 30 Live 32 System Setting 35 Network Setting 38 Camera Configuration 40 A/V Streams Setting 41 User Setting 43 Events Setting 45 Help
appendix
46 46 Product Specification 48 Troubleshooting (FAQ) 48 Pelco Troubleshooting Contact Information 49 Product Overview 53 Open Source License Report on the Product
Page 4
4 | Overview
Overview IMpOrtant Safety InStruCtIOnS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases shall be placed on the apparatus.
16. WarnInG : To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
17. Installation should be done only by qualified personnel and conform to all local codes.
18. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.
19. Use only installation methods and materials capable of supporting four times the maximum specified load.
20. A readily accessible disconnect device shall be incorporated in the building installation wiring.
21. The socket-outlet shall be installed near the equipment and shall be easily accessible.
22. A CCC approved power cord must be used to power this equipment when used in China.
Page 5
English| 5
O verview
CautIOn
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
WarnInG : This product is sensitive to Electrostatic Discharge (ESD). To avoid ESD damage to this product, use ESD safe practices during installation. Before touching, adjusting or handling this product, correctly attach an ESD wrist strap to your wrist and appropriately discharge your body and tools. For more information about ESD control and safe handling practices of electronics, please refer to ANSI/ESD S20.20-1999 or contact the Electrostatic Discharge Association (www.esda.org).
Page 6
Overview
6 | Overview
IMpOrtant nOtICeS
reGuLatOry nOtICeS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
raDIO anD teLeVISIOn InterferenCe This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commissions rules.
Can ICeS-3(a)/nMB-3(a)
LeGaL nOtICe [audio notice] SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY REQUIRE, AMONG OTHER THINGS, EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS. YOU ARE SOLELY RESPONSIBLE FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS AND FOR STRICT ADHERENCE TO ANY/ALL RIGHTS OF PRIVACY AND PERSONALTY. USE OF THIS EQUIPMENT AND/OR SOFTWARE FOR ILLEGAL SURVEILLANCE OR MONITORING SHALL BE DEEMED UNAUTHORIZED USE IN VIOLATION OF THE END USER SOFTWARE AGREEMENT AND RESULT IN THE IMMEDIATE TERMINATION OF YOUR LICENSE RIGHTS THEREUNDER.
VIDeO QuaLIty CautIOn
fraMe rate nOtICe reGarDInG uSer SeLeCteD OptIOnS Pelco systems are capable of providing high quality video for both live viewing and playback. However, the systems can be used in lower quality modes, which can degrade picture quality, to allow for a slower rate of data transfer and to reduce the amount of video data stored. The picture quality can be degraded by either lowering the resolution, reducing the picture rate, or both. A picture degraded by having a reduced resolution may result in an image that is less clear or even indiscernible. A picture degraded by reducing the picture rate has fewer frames per second, which can result in images that appear to jump or move more quickly than normal during playback. Lower frame rates may result in a key event not being recorded by the system.
Judgment as to the suitability of the products for users' purposes is solely the users' responsibility. Users shall determine the suitability of the products for their own intended application, picture rate and picture quality. In the event users intend to use the video for evidentiary purposes in a judicial proceeding or otherwise, users should consult with their attorney regarding any particular requirements for such use.
Page 7
English| 7
O verview
Open SOurCe SOftWare This product includes certain open source or other software originated from third parties that is subject to the GNU General Public License (GPL), GNU Library/Lesser General Public License (LGPL) and different and/or additional copyright licenses, disclaimers, and notices.
The exact terms of GPL, LGPL, and some other licenses are provided to you with this product. Please refer to the exact terms of the GPL and LGPL at http://www.fsf.org (Free Software Foundation) or http://www.opensource.org (Open Source Initiative) regarding your rights under said license. You may obtain a complete corresponding machine-readable copy of the source code of such software under the GPL or LGPL by sending your request to digitalsupport@pelco.com; the subject line should read Source Code Request. You will then receive an email with a link for you to download the source code.
This offer is valid for a period of three (3) years from the date of the distribution of this product by Pelco.
CCC pOWer COrD StateMent Models shipped to China do not include power cords.
note : A CCC approved power cord must be used to power the equipment when used in China.
Korean Class a eMC (A) , .
eSD WarnInG
WarnInG: This product is sensitive to Electrostatic Discharge (ESD). To avoid ESD damage to this product, use ESD safe practices during installation. Before touching, adjusting or handling this product, correctly attach an ESD wrist strap to your wrist and appropriately discharge your body and tools. For more information about ESD control and safe handling practices of electronics, please refer to ANSI/ ESD S20.20-1999 or contact the Electrostatic Discharge Association (www.esda.org).
Warranty For information about Pelcos product warranty and thereto related information, refer to www.pelco.com/warranty.
Page 8
Overview
8 | Overview
netWOrK tOpOLOGy StateMent IMpOrtant nOte. pLeaSe reaD. The network implementation is shown as a general representation only and is not intended to show a detailed network topology. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the system as illustrated. Please contact your local Pelco representative to discuss your specific requirements.
LeGaL nOtICe (auDIO nOtICe) J Improper use of audio/visual recording equipment may subject you to civil and criminal penalties. Applicable laws regarding the use of such
capabilities vary between jurisdictions and may require, among other things, express written consent from the recorded subjects. You are solely responsible for insuring strict compliance with such laws and for strict adherence to any/all right of privacy and personalty.
IntrODuCtIOn The NET5500 Series video encoder is a network-based channel encoder with a built-in, Web-based viewer for live streaming to a standard Web browser (Microsoft Internet Explorer, Chrome, Safari or Mozilla Firefox). The encoder is built upon open standards and is part of an Endura system for recording, managing, administering, and viewing video streams.
The encoder supports H.264 and MJPEG compression. It can generate two independently configurable H.264 streams, each up to D1 resolution (720 x 480 for NTSC, 720 x 576 for PAL) and 30/25 images per second (ips) in addition to an MJPEG stream for Web viewing.
The NET5500 can be configured for one alarm input for each video channel. When an alarm event is triggered, the unit can send a message to an operator, and trigger a relay.
The unit also supports motion detection for each video channel. You can configure one motion zone, with its own independent sensitivity and threshold settings. When the NET5500 detects activity in any of these areas, it can trigger an alarm event.
The video encoder supports one audio input for each video channel over the network. The system operator (security personnel) can see and hear activity in any target area in which a microphone is present.
The NET5500 supports control of remote peripherals such as pan/tilt/zoom (PTZ) cameras by way of D-Protocol, P-Protocol, and Coaxitron protocols.
featureS ~ Open standards-based architecture
~ H.264 baseline, main, or high profile compression
~ Dual-stream at up to D1, 30/25 images per second (ips) per stream
~ Integrated audio, alarm, and relay outputs
~ Integrated D-Protocol, P-Protocol, and Coaxitron protocols
Displays power On/Off status. It glows blue when the unit has power. Displays network status (connection and speed).
Off : The unit is not connected to the network. Solid amber : The unit is connected to the network using the 100 Mbps standard. Solid red : The unit is connected to the network using the 10 Mbps standard. Solid green : The unit is connected to the network using the 1 Gbps standard.
A blinking light indicates network activity corresponding to the speed based on the color. Displays camera connection status.
not Lit : A camera has not been connected yet. Green : Camera video is present at the video in connector. red : Video is no longer present, the camera is not functioning properly. Displays unit status.
Green : The unit is functioning normally. red : The unit is in an error condition.
NET5500 Series Video Encoder
a
NET5500 Series Video Encoder
a
Page 14
Overview
14 | Overview
rear paneL DeSCrIptIOn
net5501
net5504
net5508
net5516
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
a b e fc d g
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
a b efc d g
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
a b c d e f g
Tx+Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
NO3 COM3 NC3 A9 A10 A11 A12
NO4 COM4 NC4 A13 A14 A15 A16
1 3
2 4
5 7
6 8
9 11
10 12
13 15
14 162 4
1 3
6 8
5 7
10 12
9 11
14 16
13 15
a b c d e g
Page 15
English| 15
O verview
no. name Description
a
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-Power input socket. For connection of 12V adapter.
b
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
Press this switch to reset device to the factory default. If you perform the factory reset, all your settings to device will be lost. For more information, please see Factory Default (Page 18).
c
A Alarm input sensor terminal
NO/NC Relay control
COM Relay common
TX+/TX- RS-422/RS-485 Data line
RX+/RX- RS-422 RX Data line
J Disabled in RS-485 mode.
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-Ground terminal.
d
1
1
A NO COM Tx+ Rx+
NC Tx- Rx- LAN connection to a router or internal network.
e
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
Network video encoder. Audio input terminal for sound input. A microphone or other source of sound may be connected to this.
f
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
Video output BNC terminal.
g
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
Video input BNC terminal.
ptZ, relay and alarm pin assignments
Label Lead Label Lead
A1 Alarm 1 A3 Alarm 3
A2 Alarm 2 A4 Alarm 4
NO Relay Normally Open
1
1
A NO COM Tx+ Rx+
NC Tx- Rx- Ground
COM Relay Common NC Relay Normally Closed
TX+ RS-422 Data TX+ TX- RS-422 Data TX-
RX+ RS-422 Data RX+ RX- RS-422 Data RX-
Page 16
Installation
16 | Installation
SySteM OrGanIZatIOn
MOuntInG In a raCK The NET5500 Series encoder mounts into an industry-standard 48 cm (19-inch) equipment rack. The NET5500 Series encoder occupies 1 RU (4.45 cm or 1.75 inches) of vertical rack space. The hardware necessary to mount the NET5500 Series rack encoder into a rack is supplied with the unit.
the rack must meet the following requirements Rack standard : 48 cm (19 inches), EIA-310-D compliant (rear column required) Rack column depth : 50.8 to 76.2 cm (20 to 30 inches) Column mounting hole provisions : 10-32 UNF-2B threaded holes or square window holes on front and rear columns. Door systems (optional) : Front doors must have at least 5.1 cm (2 inches) between the NET5500 Series encoder front bezel and the inside of the door.
Rear doors may be used only on rack columns that more than 66 cm (26 inches) deep.
J Make sure the NET5500 Series encoder is level.
J Slots and openings in the cabinet provide ventilation to prevent the unit from overheating. Do not block these openings.
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
ptZ Camera Monitor
netWOrK
adapter MIC
Cameras
Page 17
English| 17
Installation
to install the net5500 Series encoder in a rack
1. Remove the three Phillips flat head screws from each side of the unit. Set the screws aside.
2. Align the three screw holes in the mounting brackets with the threaded holes on the left and the right sides of the chassis.
3. Using the six Phillips flat head screws, attach the mounting brackets to each side of the chassis.
4. Insert and tighten the Phillips flat head screws you removed earlier.
5. Align the two mounting bracket holes on each side with the screw holes on the rack.
6. Insert and tighten the Phillips flat head screws (not supplied) to secure the unit in the rack.
Page 18
Installation
18 | Installation
DeSKtOp InStaLLatIOn When installing the device on a horizontal surface such as a desktop, proceed as follows.
1. Attach the rubber feet to the bottom of the unit to prevent surface damage.
2. Place the device in a location that provides adequate space for wiring and cords at the front and back of the panel.
J Do not place the device upright since that can lead to its falling over and becoming damaged. Placing the device upright will also block the flow of air, which may cause it to overheat.
faCtOry DefauLt
1. Use a sharp-edged object (e.g. paper clip) to press and hold the Reset switch.
2. Press and hold the switch for 10 seconds. Then, release it.
3. When the encoder reset is completed, the system will restart by the factory default.
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1
1 A3 A4 NC Tx- Rx-
Page 19
English| 19
Installation
COnneCtInG tO an externaL DeVICe
Connecting the Monitor Connect the [
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
] port of the encoder to the output port of the monitor. You can watch the video from the camera on the monitor.
net5501
net5504
net5508
Supply LOOp Out Channel for each Model
net5501 net5504 net5508 net5516
Channel 1 4 8 None
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
Monitor 1
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
Monitor 1~4
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
Monitor 1~8
Page 20
Installation
20 | Installation
Connecting the terminal block The terminal block has tension clamps instead of screw terminals. Use a small screwdriver to open the clamp for a particular lead.
power Supply Connect the DC 12V power adapter to the encoders power input terminal.
J For safety reasons, make the connection when the power is not applied yet.
J Arrange the cables and be careful not to peel off the cable coating.
J Do not put the power cable under a carpet or rug. The power cord is usually grounded. However, even if it's not grounded, never modify it on your own for grounding.
J Do not insert multiple devices in a single power socket. This may cause a power overload.
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1
1
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1 2
1 2
3 4
3 4 2
1
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
power adapter
Page 21
English| 21
Installation
Connecting the Video Connect the [ Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
] port of the encoder to the video output port of the camera.
net5501
net5504
net5508
net5516
Supply Video Input Channel for each Mode
net5501 net5504 net5508 net5516
Channel 1 4 8 16
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
Camera 1
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
Camera 1~4
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
Camera 1~8
Tx+Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
NO3 COM3 NC3 A9 A10 A11 A12
NO4 COM4 NC4 A13 A14 A15 A16
1 3
2 4
5 7
6 8
9 11
10 12
13 15
14 162 4
1 3
6 8
5 7
10 12
9 11
14 16
13 15
Tx+Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
NO3 COM3 NC3 A9 A10 A11 A12
NO4 COM4 NC4 A13 A14 A15 A16
1 3
2 4
5 7
6 8
9 11
10
13 15
14 162 4
1 3
6 8
5 7
10 12
9 11
14 16
13 15
Camera 1~16
Page 22
Installation
22 | Installation
Connecting the audio Connect the audio input device such as microphone to the [ Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
] port.
net5501
net5504
net5508
net5516
Supply audio Input Channel for each Mode
net5501 net5504 net5508 net5516
Channel 1 4 8 16
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
MIC 1
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
MIC 1~4
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
MIC 1~8
Tx+Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
NO3 COM3 NC3 A9 A10 A11 A12
NO4 COM4 NC4 A13 A14 A15 A16
1 3
2 4
5 7
6 8
9 11
10 12
13 15
14 162 4
1 3
6 8
5 7
10 12
9 11
14 16
13 15
Tx+Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
NO3 COM3 NC3 A9 A10 A11 A12
NO4 COM4 NC4 A13 A14 A15 A16
1 3
2 4
5 7
6 8
9 11
10 12
13 15
14 162 4
1 3
6 8
5 7
10 12
9 11
14 16
13 15
MIC 1~16
Page 23
English| 23
Installation
Connecting the relay Input/Output
net5501
net5504
net5508
net5516
Supply relay Input/Output Channel for each Mode
net5501 net5504 net5508 net5516
Relay Input 1 4 8 16
Relay Output 1 1 2 4
RS-422/RS-485 1 1 1 1
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
1
1
A NO COM Tx+ Rx+
NC Tx- Rx-
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 C Tx- Rx-
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7 8
7 82 4
1 3
6 8
5 7
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7
72 4
1 3
6 8
5 7
Tx+Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
NO3 COM3 NC3 A9 A10 A11 A12
NO4 COM4 NC4 A13 A14 A15 A16
1 3
2 4
5 7
6 8
9 11
10 12
13 15
14 162 4
1 3
6 8
5 7
10 12
9 11
14 16
13 15
Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
1 2
1 2
3 4
3 4
5 6
5 6
7
72 4
1 3
6 8
5 7
Tx+Tx- NO1 COM1 NC1 A1 A2 A3 A4
Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8
NO3 COM3 NC3 A9 A10 A11 A12
NO4 COM4 NC4 A13 A14 A15 A16
1 3
2 4
5 7
6 8
9 11
10 12
13
142 4
1 3
6 8
5 7
10 12
9 11
14 16
13 15
Page 24
Installation
24 | Installation
Connecting the relay Input Connect the signal line of an relay input device such as sensor to the rear [a] port.
Connecting the relay Output Connect the signal line of an relay output device to the rear [nO/nC/COM] port.
Connecting the rS-422/rS-485 Device Connect the external device to the [rS-422/rS-485 Data line ] ports. You can connect and control PTZ camera that supports RS-422/RS-485 communication.
Page 25
English| 25
Installation
network Connection
pC Connection in the Local network You can connect the encoder to a PC in the same network and control or manipulate it on the PC monitor.
1. Connect the network port in the rear panel to the router or hub.
2. Connect the local PC to the router or hub.
3. Enter the address in the address bar (web browser) of the local PC or of the dedicated software program in the format of http://Ip address:web service port. (Ex : http://192.168.0.23:80) From the Network Setup screen, you can change the port number.
If you do not know the camera's IP address, you can locate it using the Pelco Device Utility Software.
4. Provide the ID and password before logging in. Then, you can view the monitoring screen. Access ID (factory default) : admin, P/W : admin.
J For security purposes, change the password right after you purchase the product.
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
Camera 1
Local pC Local pC
Broadband router
Camera 2 Camera 3
Camera 4
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
4WANRESETPWR 3 2 1
Local pC Local pC
Broadband router
Page 26
Installation
26 | Installation
pC Connection from a remote network You can connect the encoder to a PC or mobile device in the same remote network and control or manipulate it on the monitor of the PC or mobile device
1. Connect the network port in the rear panel to the router.
2. Connect the [netWOrK] port of the router directly to the fixed IP LAN cable, or connect it to the ADSL modem.
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
Internet Direct
connection
Local pC Local pCLocal pC
Broadband router
Internet
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
1 2
1 2
3 4
3 4 2 4
1 3
A1 A2 NO COM Tx+ Rx+
A3 A4 NC Tx- Rx-
4WANRESETPWR 3 2 1
aDSL modem Local pC
Broadband router
Page 27
English| 27
W eb View
er
Web Viewer What IS the WeB VIeWer?
Minimum pC requirement
CPU P4 3.0 or Higher
RAM 512MB or Higher
VGA GeForce MS 400, Radeon 7500 or higher
GeForce 8 series or higher
VGA MEMORY 64MB
MONITOR 1280 X 1024
BROWSER Internet Explorer, Firefox, Chrome, Safari
accessing the encoder and attached Cameras The first time you access the camera, the live video page appears. By default, you are viewing the video as a public user and only have access to the single stream live view.
If, for security purposes, users should not be allowed to view video without first logging on to the camera, change the permissions for public users.
Page 28
Web Viewer
28 | Web Viewer
pelco Media player Installation To view videos after accessing the Web viewer, the Pelco Media Player plug-in must be installed. Install Pelco Media Player from the CD included with the player.
The Pelco Media Player 1.9.5 or higher is required for multiple channels.
1. Run InstallPelcoMediaPlayer.msi.
2. Click the [next>] button to start installation.
3. Click the [Close] button. Pelco Media Player Installation is complete.
Page 29
English| 29
W eb View
er
Logging In Entering the IP address of the camera as a URL into the web browser will immediately bring up the Live Mode screen if the encoder is not setup to require authentication (Open Authentication option). If the camera is setup to require authentication, then the user will be prompted for a Username and Password before being able to see the live video feed.
1. Click on the live screen.
2. Enter your and .
Default username : admin, Password : admin
3. Click the button.
The Open Authentication option is configured on the Settings > Users > General Settings screen.
Change your password Please change the password for your security.
1. Click from the live screen.
2. Enter your new password.
3. Click the button.
Page 30
Web Viewer
30 | Web Viewer
LIVe
Live Screen Overview Live Mode Screen Components
no. name Description
a Channel Name Displays the name assigned to the channel selected.
b Video Channel Choose number 1 to the number of channels on the encoder.
c Multi-Function Image Button
$ Tilt Up
% Tilt Down
+ Pan Right
_ Pan Left
Home Preset
d Control the Zoom Activates Zoom in (-) / Zoom out (+) features.
e Control the Focus Activates Near (-) / Far (+) features.
f Control the Iris Adjusts the camera brightness.
g Move to Presets Moves to the preset selected.
i
a
l
k j
m
n
b
g
h
c
d e f
Page 31
English| 31
W eb View
er
no. name Description
h Pattern Activates the pattern selected.
i Stream Selection Selects the viewable video stream that displays in live view (Primary, Secondary, QuickView) and selects unicast or multicast and throttle settings.
It will not be presented to users who are designated as Viewers.
j View the Selected Tab Composed of Live, Settings, Help, and Logout settings menus.
k Maximize Viewing Area
Scales the image to the full size of the browser. To resize the video pane to normal view, click the Show Toolbar button in the upper-right corner of the window.
l Take a Snapshot Captures the image displayed in the video pane and saves it as a JPEG file.
m Open Stream in New Window
Opens the video in a scalable, independent window. Opening the video in a separate window allows you to view the video while other applications are running. This window can be minimized, maximized, or closed using the title bar buttons of the active window. The window can also be resized by dragging a corner of the window.
n Pan/Tilt/Zoom
Control the encoder and the pan (left/right) and tilt (up/down) of the connected camera by dragging the mouse. Also, zoom using the scroll wheel on the mouse.
These icons are always available when using the Pelco Media Player. If you are using QuickTime, PTZ overlay is only available with PMP player.
Selecting a Stream
1. Click < > from the live screen. Move to the Stream settings screen.
2. Select one of the following streams.
~ Primary STREAM : To select this stream, click the button next to Primary Stream.
~ Secondary STREAM : To select this stream, click the button next to Secondary Stream.
~ QuickView STREAM : To select this stream, click the button next to QuickView Stream. If the secondary stream has not been configured,
only Primary Stream, and QuickView Stream are available.
3. Select the transmission.
~ Unicast : A unicast transmission sends a separate video stream to each user that is requesting data. Although multiple users might request the same data from the encoder at the same time, duplicate video streams are transmitted to each user. Every unicast user that connects to the encoder consumes additional processing power, which limits the number of simultaneous users who can access the camera.
~ Multicast : A multicast transmission sends data to multiple users at the same time using one transmission stream. Each multicast user that connects to the camera consumes no additional processing power; therefore, multicast video streams can be sent to an unlimited number of simultaneous users. The multicast transmission setting is available in the primary and secondary stream display settings.
4. Select the Player.
5. Click the
Related manuals for Pelco NET5501 Encoder Installation Manual
If you want to find out how the NET5501 Pelco works, you can view and download the Pelco NET5501 Encoder Installation Manual on the Manualsnet website.
Yes, we have the Installation Manual for Pelco NET5501 as well as other Pelco manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Installation Manual should include all the details that are needed to use a Pelco NET5501. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Pelco NET5501 Encoder Installation Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Pelco NET5501 Encoder Installation Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Pelco NET5501 Encoder Installation Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Pelco NET5501 Encoder Installation Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Pelco NET5501 Encoder Installation Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.
en
