Pelco C5637M-A Card Cage Installation Manual PDF

1 of 6
1 of 6

Summary of Content for Pelco C5637M-A Card Cage Installation Manual PDF

TECH SUPPORT: (800) 289-9100 INTERNATIONAL: +1 (559) 292-1981 C5637M-A / REV 07-24-14

INSTALLATION AND OPERATION MANUAL

EU/USRACK RACK MOUNT CARD CAGE WITH POWER SUPPLY

This racks integral 115/230 VAC power supply provides for the elimination of a single-point failure in the event of a major fault within any module located within the chassis rack, through the use of automatic electronic current limiting within each rack-mountable module.

In the power supply design only the faulty module shuts down, and the operation of the other modules within the rack continue unimpaired. This automatic current limiting feature is also self-resetting, should the fault or overload be of a temporary or intermittent condition.

The power supply is intended to be installed in the Pelco Card Cage only. Any other applications are not supported. See Page 3 for installation instructions.

TECH SUPPORT: (800) 289-9100 INTERNATIONAL: +1 (559) 292-1981 C5637M-A / REV 07-24-14

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases shall be placed on the apparatus.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 16. Installation should be done only by qualified personnel and conform to all local codes. 17. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must

not be installed where exposed to rain and moisture. 18. Use only installation methods and materials capable of supporting four times the maximum specified load. 19. A CCC-approved power cord must be used to power this equipment when used in China. 20. In order to satisfy the EU Regulatory compliance Standards, the use of a universal power supply (UPS) is required on the AC mains. 21. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not

perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.

TECH SUPPORT: (800) 289-9100 INTERNATIONAL: +1 (559) 292-1981 C5637M-A / REV 07-24-14

INSTALLATION AND OPERATION MANUAL EU/USRACK

FIGURE 1 RACK INTEGRAL POWER SUPPLY

FIGURE 2 LED INDICATORS

POWER RED Unit powered up OFF Unit powered down

ELECTRICAL Input Voltage: 90-264 VAC @ 70 W Maximum Output Voltage: 9 VDC +/- 5% @ 6.5 Amps @ 75C

Detachable, IEC-connected AC Line Cord allows easy field replacement or exchange for various worldwide AC power plug configurations (use only manufacturers supplied cord).

A

POWER

EURACK

FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE FUSE

CAUTION!

Input: 90-264 VAC @1.0 Amps 50/60 Hz

Fuse: 1.250A SB, 250 VAC Output: 9.0 VDC @ 6.5 Amps Model: EUPS File Number: E354877 C

N -9 -A -E U PS

CHASSIS GROUNDING STUD (6-32 Thread)

SPARE 1.25A SLOW BLOW FUSE

A

POWER

EURACK

FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE FUSE

CAUTION!

Input: 90-264 VAC @1.0 Amps 50/60 Hz

Fuse: 1.250A SB, 250 VAC Output: 9.0 VDC @ 6.5 Amps Model: EUPS File Number: E354877 C

N -9 -A -E U PS

REAR PANEL (In Rack)FRONT PANEL (In Rack)

RED or BLACK WITH WHITE STRIPE BLACK

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below: Five years:

Fiber optic products Unshielded Twisted Pair (UTP) transmission products CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models Three years:

FD Series and BU Series analog camera models Fixed network cameras and network dome cameras with Sarix technology Sarix thermal imaging products (TI and ESTI Series) Fixed analog camera models (C20 Series, CCC1390H Series, C10DN Series,

and C10CH Series) EH1500 Series enclosures Spectra IV products (including Spectra IV IP) Spectra HD dome products Camclosure IS Series integrated camera systems DX Series video recorders (except DX9000 Series which is covered for a

period of one year), DVR5100 Series digital video recorders, Digital Sentry

Series hardware products, DVX Series digital video recorders, and NVR300 Series network video recorders

Endura Series distributed network-based video products Genex Series products (multiplexers, server, and keyboard) PMCL200/300/400 Series LCD monitors PMCL5xxF Series and PMCL5xxNB Series LCD monitors

Two years: Standard varifocal, fixed focal, and motorized zoom lenses DF5/DF8 Series fixed dome products Legacy Series integrated positioning systems Spectra III, Spectra Mini, Spectra Mini IP, Esprit, ExSite, ExSite IP, and

PS20 scanners, including when used in continuous motion applications Esprit Ti and TI2500 Series thermal imaging products Esprit and WW5700 Series window wiper (excluding wiper blades) CM6700/CM6800/CM9700 Series matrix Digital Light Processing (DLP) displays (except lamp and color wheel). The

lamp and color wheel will be covered for a period of 90 days. The air filter is not covered under warranty.

Six months: All pan and tilts, scanners, or preset lenses used in continuous motion

applications (preset scan, tour, and auto scan modes) Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to a Pelco designated location. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelcos liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or consequential damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number 2. Date of shipment, P.O. number, sales order number, or Pelco invoice number 3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

Revised 1-12-12

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pe .cnI ,ocleP ,2102 thgirypoC .setailiffa sti ro .cnI ,ocl All other product names and services are the property of their respective companies . All rights reserved. Product specifications and availability are subject to change without notice.

Pelco, Inc. 625 W. Alluvial Fresno, California 93711 United States USA & Canada Tel (800) 289-9100 Fax (800) 289-9150

International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120

www.pelco.com

Manualsnet FAQs

If you want to find out how the C5637M-A Pelco works, you can view and download the Pelco C5637M-A Card Cage Installation Manual on the Manualsnet website.

Yes, we have the Installation Manual for Pelco C5637M-A as well as other Pelco manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Manual should include all the details that are needed to use a Pelco C5637M-A. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Pelco C5637M-A Card Cage Installation Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Pelco C5637M-A Card Cage Installation Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Pelco C5637M-A Card Cage Installation Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Pelco C5637M-A Card Cage Installation Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Pelco C5637M-A Card Cage Installation Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.