ENGLISH Thank you for purchasing a Panasonic product. This product is designed for use with the Panasonic FZ-N1 and FZ-F1 series (hereinafter referred to as the unit) (as of December 2019). (Cannot be used with some models.) Please read this document carefully before using the product and keep this document in a
safe place for future reference. Refer to the Operating Instructions included with the unit for information about installation
and removal of the battery cover and battery. Some illustrations in this document may look different from the actual product. Information in this document is subject to change without notice.
Handling and maintenance Take care as there is a risk of the unit dropping when the hand strap is loose. Do not use the hand strap if it is worn out or damaged. For typical cleaning, wipe the hand strap with a soft, dry cloth.
If the hand strap becomes dirty, wet a soft cloth with water and wring it thoroughly before wiping the hand strap.
Do not clean the hand strap with benzene, thinner, alcohol, household cleansers, etc., as these may harm the hand strap.
Attaching
1 Turn off the unit, and place it on a flat surface such as a desk with the screen face down. Make sure there are no foreign objects under the unit.
2 Remove the battery cover of the unit, and then remove the dummy mount (A). Remove the dummy mount straight out.
3 Attach the battery cover, insert the hand strap mount (B) into the unit, and then push in until you hear a click. Insert the mount straight in.
4 Adjust the hand strap to fit on your hand, and then fold back and fasten the belt. (If the belt is too long, insert it into the hole (C).) Insert your hand into position D as shown in the
illustration. Fold back and fasten the belt so that the white line (E)
on the belt is not visible. If the white line is visible, the belt may come loose because it is not fastened enough.
If the belt is long or if the extra length of belt is not inserted into the hole, the belt may be included when using the camera of the unit. Adjust the belt so that it does not interfere with the camera.
Operating Instructions / Bedienungsanleitung Instructions dUtilisation / Hand Strap / Handschlaufe Courroie de main /
Model No.
DHQP1068ZA/J1 C1219-0
Web site: https://panasonic.net/cns/pc/
Panasonic Mobile Communications Co., Ltd. 2019
5 Pass the attachment lace through both strap attachment holes of the unit (F), and then secure the lace to the hand strap ring (G). Pass the attachment lace as shown in the illustration. Secure the attachment lace to each ring. Make sure that the attachment lace is secured to
the ring.
6 Close the pad (H) and fasten. Make sure not to close the pad over the hand strap. A pen holder (I) is also attached. To remove, follow the procedure for attaching in reverse.
Replacing the battery
1 Open the pad (A), remove the mount (B), and then fold back the entire hand strap (C).
2 Replace the battery.
3 Attach the mount and fasten the pad.
DEUTSCH Vielen Dank, dass Sie sich fr den Kauf dieses Panasonic-Produkts entschieden haben. Dieses Produkt ist fr die Verwendung mit den Panasonic-Serien FZ-N1 und FZ- F1 konzipiert (nachstehend als das Gert bezeichnet) (ab Dezember 2019). (Kann mit einigen Modellen nicht verwendet werden.) Lesen Sie vor der Verwendung des Produkts dieses Dokument sorgfltig und bewahren
Sie es zum spteren Nachschlagen an einem sicheren Ort auf. Informationen zum Abnehmen der Akkufachabdeckung und Herausnehmen des Akkus
finden Sie in der mit dem Gert gelieferten Bedienungsanleitung. Einige Abbildungen in diesem Dokument knnen vom tatschlichen Produkt abweichen. Die Informationen in diesem Dokument knnen ohne vorherige Ankndigung gendert werden.
Pflege und Wartung Seien Sie vorsichtig, da das Gert herunterfallen kann, wenn die Handschlaufe lose ist. Verwenden Sie die Handschlaufe nicht, wenn sie verschlissen oder beschdigt ist. Wischen Sie die Handschlaufe zur normalen Reinigung mit einem weichen, trockenen Tuch ab.
Bei einer verschmutzten Handschlaufe ein weiches Tuch mit Wasser anfeuchten, grndlich auswringen und dann die Handschlaufe abwischen.
Reinigen Sie die Handschlaufe nicht mit Benzol, Verdnner, Alkohol, Haushaltsreinigungsmitteln usw., da diese die Handschlaufe beschdigen knnen.
Befestigung
1 Schalten Sie das Gert aus und legen Sie es mit dem Bildschirm nach unten auf eine ebene Flche, wie z. B. einen Schreibtisch. Achten Sie darauf, dass sich keine Fremdkrper unter
dem Gert befinden.
2 Entfernen Sie die Akkufachabdeckung des Gertes und die Befestigungsattrappe (A). Ziehen Sie die Befestigungsattrappe gerade heraus.
3 Setzen Sie die Akkufachabdeckung und die Handschlaufenbefestigung (B) in das Gert ein und schieben Sie sie hinein, bis sie hrbar einrastet. Schieben Sie die Befestigung gerade hinein.
4 Stellen Sie die Handschlaufe auf Ihre Hand ein und falten Sie die Handschlaufe dann zurck und ziehen Sie sie fest. (Falls die Handschlaufe zu lang ist, fhren Sie sie in das Loch (C) ein.) Fhren Sie Ihre Hand in die Position D ein (siehe
Abbildung). Falten Sie die Handschlaufe und ziehen Sie sie so
fest, dass die weie Linie (E) auf der Handschlaufe nicht sichtbar ist. Falls die weie Linie sichtbar ist, knnte sich die Handschlaufe lsen, weil sie nicht ausreichend festgezogen ist.
Bei einem langen oder aus dem Loch herausragenden Riemen kann es sein, dass der Riemen bei Verwendung der Gertekamera mit einbezogen wird.Stellen Sie den Riemen so ein, dass er den Kamerabetrieb nicht behindert.
5 Fhren Sie die Befestigungsschnur durch beide Handschlaufenlcher des Gertes (F) und sichern Sie die Schnur am Handschlaufenring (G). Fhren Sie die Befestigungsschnur wie in der
Abbildung dargestellt. Sichern Sie die Befestigungsschnur an jedem Ring. Stellen Sie sicher, dass die Befestigungsschnur am
Ring gesichert ist.
6 Das Polster (H) schlieen und befestigen. Achten Sie darauf, dass Sie das Polster nicht ber
der Handschlaufe schlieen. Ein Stiftehalter (I) ist ebenfalls integriert. Zum Entfernen, die Prozedur zum Anbringen in
umgekehrter Reihenfolge ausfhren.
FZ-VSTN11BU