Contents

Panasonic AG-DVX200PJ, AG-DVX200PB Operating Instructions PDF

1 of 203
1 of 203

Summary of Content for Panasonic AG-DVX200PJ, AG-DVX200PB Operating Instructions PDF

until 2015/9/30

Operating Instructions

Memory Card Camera-Recorder Model No. AG-DVX200PJ

AG-DVX200PB AG-DVX200PX AG-DVX200EJ AG-DVX200EN AG-DVX200ED

Vol.2

Please read these instructions carefully before using this product, and save this manual for future use.

This document explains in detail how to operate this device. Concerning basic operation, please refer to the enclosed Operating Instructions Vol.1 (printed document).

Vol.2

SQT1051

ENGLISH F0815MT0

About the recording method for recording motion pictures

This unit can record motion pictures using three different recording methods, including MOV, MP4 and AVCHD*. (l 33, 141) * AVCHD Progressive (1080/60p, 1080/50p)

supported.

MOV and MP4: These recording methods are suitable for editing images. Audio is recorded in linear PCM. Those methods are not compatible with

motion pictures recorded in AVCHD format. Those methods can record motion pictures in

formats that support 4K. 4K motion pictures offer a resolution four times higher than that of full high-definition motion pictures.

AVCHD: This recording method is suitable for playback on a high-definition compatible external monitor. Audio is recorded in Dolby Digital.

Regarding system frequencies The NTSC/PAL region setting can be switched in [SYSTEM FREQ]. (l 141, 178) You cannot store AVCHD scenes recorded

with different system frequencies on the same SD card. If you have switched the system frequency, use another SD card.

Indemnity about recorded content

Panasonic does not accept any responsibility for damages directly or indirectly due to any type of problems that result in loss of recording or edited content, and does not guarantee any content if recording or editing does not work properly. Likewise, the above also applies in a case where any type of repair is made to the unit.

About Condensation (When the lens, the viewfinder or LCD Monitor is fogged up)

Condensation occurs when there is a change in temperature or humidity, such as when the unit is taken from outside or a cold room to a warm room. Please be careful, as it may cause the lens, the viewfinder or LCD monitor to become soiled, moldy, or damaged. When taking the unit to a place which has a different temperature, if the unit is accustomed to the room temperature of the destination for about one hour, condensation can be prevented. (When the difference in temperature is severe, place the unit in a plastic bag or the like, remove air from the bag, and seal the bag.) When condensation has occurred, remove the battery and/or the AC adaptor and leave the unit like that for about one hour. When the unit becomes accustomed to the surrounding temperature, fogginess will disappear naturally.

Read this first

- 2 -

About security Be careful about the possibility of theft or loss of the unit, and be careful not to leave the unit unattended. Please note that Panasonic does not accept any responsibility for the compromise, manipulation, and loss of information caused by these events.

Caution regarding laser beams The lens may suffer damage if struck by a laser beam. Make sure that laser beams do not strike the lens when shooting in an environment where laser devices are used.

Cards that you can use with this unit

SDHC Memory Card and SDXC Memory Card 4 GB or more Memory Cards that do not have

the SDHC logo or 48 GB or more Memory Cards that do not have the SDXC logo are not based on SD Memory Card Specifications.

Refer to page 21 for more details on SD cards.

For the purposes of these operating instructions

The battery pack is referred to as the Battery.

SDHC Memory Card and SDXC Memory Card are referred to as the SD card.

Function that can be used for Recording Mode: Function that can be used for Playback Mode:

Scene(s) recorded with [REC MODE] set to [MOV] or [MP4]: "MOV/MP4 scene(s)".

Scene(s) recorded with [REC MODE] set to [AVCHD]: "AVCHD scene(s)".

Pages for reference are indicated by an arrow, for example: l 00

These operating instructions are designed for use with models AG-DVX200PJ/PB/PX/EJ/ EN/ED. Such as screen illustrations are as an example AG-DVX200PJ.

- 3 -

Read this first .................................................2

Preparation What you can do with this unit ..................... 6

Recording to the SD card ........................ 6 Linking to external devices ...................... 6

Names and Functions of Main Parts ............8 Power supply................................................ 15

Charging the battery .............................. 16 Inserting/removing the battery ............... 17 Charging and recording time ................. 18 Connecting to the AC outlet................... 20

Preparation of SD cards ..............................21 Cards that you can use with this unit......................................................... 21 Inserting/removing an SD card .............. 22

Turning the unit on/off................................. 23 Selecting a mode .........................................23 Using the LCD monitor/Viewfinder............. 24

Setting how to turn on/off the LCD monitor and Viewfinder .......................... 24 Using the LCD monitor .......................... 24 How to use the touch screen ................. 25 LCD monitor adjustment........................ 26 Viewfinder adjustment ........................... 27 Recording yourself................................. 28

Setting date and time...................................29 Using the menu screen ...............................30

Recording Before recording ..........................................31 Selecting the Recording Method................ 31

Formatting media................................... 32 Selecting a media to record ........................ 32 Recording motion picture with this unit ................................................................ 33 Recording still pictures ...............................34 Switching between Auto and Manual Mode..............................................................36 Adjusting the Picture Quality...................... 38 Using the zoom ............................................ 40 Image Stabilizer Function ........................... 42 Focus ............................................................ 44

One Push AF ......................................... 47 Push AF................................................. 48 Focus Assist .......................................... 48

Manual Focus Assist.............................. 51 Focus Transition .................................... 52

White Balance...............................................55 Iris/Gain adjustment.....................................59

Iris adjustment........................................ 59 Gain adjustment..................................... 61

Manual shutter speed ..................................63 Audio Input ...................................................66

Switching Audio Input ............................ 66 Adjusting the audio input level ............... 68

Counter display ............................................70 Setting the Time Code ........................... 70 Setting the User Information .................. 72 Setting the Recording Counter............... 73 Synchronizing the time code with an external device....................................... 73

USER button .................................................74 Setting the USER button........................ 74 Using the USER button.......................... 75 Functions of the USER button ............... 76

Useful functions ...........................................95 Color Bar Screen ................................... 95 ND filter .................................................. 96 Switching the screen indications/mode information display ................................. 96

Using Operation Icons.................................97 Using of jog dial ...........................................98

Playback Motion picture/Still picture playback .......101

Motion picture playback using operation icon ...................................... 105

Useful functions .........................................106 Creating still picture from motion picture .................................................. 106 Repeat Playback.................................. 107 Resuming the previous playback ......... 107 Playing back scenes or still pictures by date ...................................................... 108

Editing Deleting scenes/still pictures....................109

Protecting scenes/still pictures............. 110 Copying between SD cards....................... 111

Contents

- 4 -

Linking to external devices Connecting Headphones, a Remote Control or an External Monitor ................. 113

Headphones ........................................ 113 Remote control .................................... 113 External monitor .................................. 114 Setting the external output resolution ............................................. 115

Connecting to a PC (File transfer/nonlinear editing) ................ 121

Operating environment (mass storage)..................................... 121 Connecting to a PC ............................. 122 About the PC display ........................... 123

Copying/playing back with an external media device .............................................. 125

Preparing for copying/playing back ..................................................... 125 Differential copy ................................... 127 Copy selected files .............................. 128 Playing back the External Media ......... 129

Menu Using the Menu .......................................... 130

Scene file............................................. 130 System mode....................................... 141 User switch .......................................... 149 Switch setting ...................................... 150 Auto switch setting............................... 157 Recording Setup.................................. 159 Audio Setup ......................................... 166 Output Setup ....................................... 167 Display setting ..................................... 171 Other Functions ................................... 176 Maintenance ........................................ 179 Video Setup ......................................... 179 Picture Setup ....................................... 180 Copy .................................................... 180

Display Indications ..................................................181 Messages.................................................... 185

Others Troubleshooting .........................................189

About recovery..................................... 193 Updating the firmware incorporated into the unit ........................................................193 Cautions for use.........................................194 About copyright .........................................198 Recording functions that cannot be used simultaneously..................................199 Recording modes/approximate recordable time ..........................................200 Approximate number of recordable pictures .......................................................202

- 5 -

This unit is a 4K*1 camera recorder with the following features: *1 Please refer to page 142 about recording format of this unit. The 4/3-type large sensor allows you to record beautifully defocused images with shallow depth

of field as ultra high-definition 4K motion picture. V-Log L (12 stops) allows you to record expressive images with greater latitude. Recording at a variable frame rate of up to 120 fps (for FHD) is possible. It incorporates the 5-Axis Hybrid Image Stabilizer, Custom AF function, and ND filters (1/4, 1/16,

and 1/64). Supported recording media include SDHC Memory Card and SDXC Memory Card.

Recording to the SD card A variety of recording functions support recording to the SD card. This unit supports relay/simultaneous/background/dual codec recording using double card slots.

Linking to external devices

Transfer data (files) to perform nonlinear editing on another device (PC, etc.). This unit supports USB 3.0.

*2 SD cards are optional and not supplied with this unit. *3 A USB 3.0 cable is not supplied with this unit. Use a commercially-available double-shielded

USB 3.0 cable with a ferrite core. If possible, we recommend using a cable with a length of 1.5 m (4.9 feet) or less.

Preparation

What you can do with this unit

USB Device Mode

A SDHC Memory Card/SDXC Memory Card*2

B USB 3.0 (Device mode)*3

C PC

- 6 -

If you connect an external media device, such as USB HDD or USB flash memory (commercially- available) to this unit, you can copy motion pictures and still pictures recorded on this unit to the external media device. It can also play back the scenes and still pictures copied to the external media device. This unit supports USB 3.0.

Connect an external monitor to output images. It is also possible to output 4:2:2 (10 bit) images, depending on the [OUTPUT BITS] setting.

*1 Use a commercially-available audio cable (3.5 mm (0.14 q) diameter jack to RCA cable). *2 Use a commercially-available High Speed HDMI cable.

If possible, we recommend using a cable with a length of 3 m (9.84 feet) or less. *3 To connect to the SDI OUT or VIDEO OUT terminal, use a double-shielded BNC cable

equivalent to 5C-FB (commercially-available).

USB Host Mode

Refer to the following support site for information about an external media device. http://pro-av.panasonic.net/ (This Site is English only)

Connecting to an external monitor

When connecting with an HDMI cable using an HDMI-to-DVI converter, etc., be sure to connect the HDMI cable to the connector of this unit last. Connecting the HDMI cable to the connector of this unit first may result in malfunction.

A USB 3.0 (Host mode) B External media device (commercially-available)

A Audio cable*1

B HDMI cable*2 C BNC cable*3

D External monitor

- 7 -

1 USB HOST terminal (l 125) 2 USB DEVICE terminal (l 122) 3 HDMI OUT connector [HDMI] (l 114) 4 Handle 5 Lens hood release button (l 12) 6 Audio input terminal 1 (XLR 3 pin)

[AUDIO INPUT1] (l 14, 67) 7 Microphone holder attachment part

(l 14) 8 Lens hood (l 12) 9 Status indicator (l 23) 10 Power switch (l 23) 11 Recording start/stop button (l 33) 12 DC input terminal [DC IN] (l 20) Do not use any other AC adaptors except the

supplied one.

13 SDI OUT terminal (l 114) 14 TC PRESET IN/OUT terminal (l 73) 15 VIDEO OUT terminal (l 114) 16 Headphone terminal [ ] (l 100, 113) Excessive sound pressure from earphones

and headphones can cause hearing loss. Listening at full volume for long periods may

damage the users ears. 17 AUDIO OUT terminal (l 114) 18 Camera remote terminal [CAM

REMOTE] (l 113) FOCUS IRIS terminal (3.5 mm (0.14 q)

diameter mini jack) ZOOM S/S terminal (2.5 mm (0.1 q) diameter

super mini jack) 19 Pin holder Attaches the zoom ring pin removed from this

unit. 20 Speaker 21 Shoulder strap fixture (l 13) 22 Inlet (cooling fan) (l 31) 23 Hand strap (l 13) 24 Audio input terminal 2 (XLR 3 pin)

[AUDIO INPUT2] (l 14, 67)

Preparation

Names and Functions of Main Parts 4

7

6

9 8

10 11

12 13 14 15

18 17 16

23 22

20 19

21

24

5

3

1 2

- 8 -

25 Tripod receptacle (l 14) 26 Eyepiece corrector lever (l 27) 27 ND filter switch [ND FILTER] (l 96) 28 Focus auto/Manual/ switch

[FOCUS A/M/] (l 44) 29 Iris button [IRIS] (l 59) 30 FOCUS ASSIST button (l 48) 31 User 1 button [USER1] (l 74) 32 User 2 button [USER2] (l 74) 33 User 3 button [USER3] (l 74) 34 User 4 button [USER4] (l 74) 35 PUSH AUTO button (l 44) 36 Focus ring (l 44) 37 Zoom ring (l 40) 38 Zoom ring pin 39 Iris ring (l 59)

40 User 5 button [O.I.S.] (l 42, 74) 41 User 6 button [ZEBRA] (l 74, 88) 42 User 7 button [WFM] (l 74, 87) 43 Zoom switch [MANU/SERVO] (l 40) 44 Display/Mode check switch [DISP/

MODE CHK] (l 75, 96) 45 Gain switch [GAIN] (l 61) 46 White Balance switch [WHITE BAL]

(l 55) 47 Jog dial [SEL/PUSH SET] (l 55, 61, 63,

98, 103) 48 Menu button [MENU] (l 30) 49 Shutter speed button [SHUTTER] (l 63) 50 Auto/Manual switch [AUTO/MANU]

(l 36)

25

36 37 3938 454443 46 47 48 49 50

32 3328

31 30

34 35

29

27

424140

26

- 9 -

51 SD Card slot cover (l 22) 52 Access lamp (card 1) (l 22) 53 Card slot 1 (l 22) 54 Access lamp (card 2) (l 22) 55 Card slot 2 (l 22) 56 INPUT1 / INPUT2 switches (l 66) 57 CH1 SELECT/CH2 SELECT switches

(l 66) 58 CH1/CH2 switches (l 66) 59 AUDIO LEVEL CH1/AUDIO LEVEL CH2

knobs (l 68) 60 LCD monitor extract part (l 24) 61 LCD monitor (Touch screen) (l 25) 62 Lens cover open/close lever (l 12) 63 Recording lamp (Rear) (l 177) 64 Shoulder strap fixture (l 13)

65 Eye cup mount (l 13) 66 Eye sensor (l 28) 67 Viewfinder (l 27) 68 Eye cup (l 13) 69 Open/close lever [OPEN] (l 17) 70 Battery cover (l 17) 71 Battery holder (l 17) 72 Battery release lever [BATTERY] (l 17) 73 Built-in microphone 74 Recording lamp (Front) (l 177) 75 Lens cover (l 12) 76 Exhaust opening (cooling fan) (l 31) 77 Lens (LEICA DICOMAR) 78 Auto white balance button [AWB] (l 55)

595756 58

51 6160 63 64 66 6765625352

5554 68 69 70

72 71

75

74

77

78

76

73

- 10 -

79 Accessory shoe 80 Sub zoom lever (l 40, 156) This lever functions in the same manner as

the zoom lever. 81 Zoom lever [T/W] (In Recording Mode)

(l 40) Volume lever [rVOLs]/ Thumbnail display switch [ / ] (In Playback Mode) (l 103)

82 User 8 button [REC CHECK] (l 74, 80) 83 Handle mounting hole (Size of the mounting hole)

j 1/4-20UNCk2 j 3/8-16UNCk2

84 Thumbnail button [THUMBNAIL] (l 23) 85 Counter button [COUNTER] (l 70) 86 Counter reset/Time code setting button

[RESET/TC SET] (l 72, 73) 87 Color Bar Screen button [BARS] (l 95) 88 Sub recording start/stop button (l 156) This button functions in the same manner as

the recording start/stop button.

84 85 86 87

79 80 81 82 83

88

- 11 -

Attaching/detaching the lens hood (How to detach the lens hood) While pressing and holding the lens hood release button, rotate the lens hood in the direction of the arrow to detach it.

(How to attach the lens hood)

1 Fit the lens hood into this unit. Align the mounting mark on the lens hood with the mounting mark on this unit. 2 Rotate the lens hood in the direction of the arrow. Rotate until it clicks into place.

Opening/closing the lens cover You can open/close the lens cover by sliding the lens cover open/close lever. When this unit is not in use, close the lens cover to protect the lens.

Do not press the lens cover hard. This may damage the lens or the lens cover. Depending on the various filters or the MC protector attached to the front side of this unit's lens,

you may not be able to open/close the lens cover or attach the lens hood.

A Lens hood release button

B Mounting mark

OPEN

CLOSE

- 12 -

Adjust the length of the hand strap so that it fits your hand. Adjust the hand strap according to the size of your hand. If you find it difficult to fasten the buckle B, move the pad A towards you, and fasten the buckle

B again.

Attaching the eye cup 1 Align the mounting mark on the eye cup mount with the corresponding mark on

the eyecup. 2 Attach the eye cup so that the notch on the eye cup mount is aligned with the

protrusion inside the eye cup.

Push the eye cup in until it reaches the mounting mark. (D)

Attaching the Shoulder strap We recommend that you attach the shoulder strap (supplied) before going out of doors to record so as to avoid dropping this unit.

1 Open the buckle. 2 Pull the end of the belt.

A Mounting marks B Notch C Protrusion

A 20 mm (0.8 q) or longer

- 13 -

Attaching the front microphone The microphone holder is set up so that a 21 mm (0.83 q) external microphone (AG-MC200G:

optional) can be attached. Check in advance whether the microphone you wish to use can be attached.

1 Attach the microphone holder to the microphone holder attachment part. Attach by using a commercially available screw driver. When attaching the microphone holder, be sure to tighten the screws firmly even though you

might hear a squeaking sound.

2 Attach an external microphone (optional) to the microphone holder, and tighten the microphone holder screw.

3 Connect the external microphone to the AUDIO INPUT1 terminal (XLR 3 pin).

When wiring the microphone cable, use the cable clamper of this unit.

Keep the microphone holder screw, zoom ring pin and INPUT terminal cap out of reach of children to prevent swallowing.

Attaching the INPUT terminal cap Attach the INPUT terminal cap while the AUDIO INPUT1, 2 terminals (XLR 3 pin) are not used.

Attaching the tripod There are tripod mounting holes that are compatible with 1/4-20UNC and 3/8-16UNC screws.

Use the size that matches the diameter of the tripods fixing screw.

A Microphone holder attachment part B Microphone holder C Microphone holder mounting screws

D AUDIO INPUT1 terminal (XLR 3 pin) E Microphone cable clamper F Microphone holder screw G External microphone (optional)

A INPUT terminal cap

- 14 -

Attaching a tripod with a screw length of 5.5 mm (0.22 q) or more may damage the unit.

About batteries that you can use with this unit (as of August 2015) The battery that can be used with this unit is VW-VBD58.

Preparation

Power supply

It has been found that counterfeit battery packs which look very similar to the genuine product are made available to purchase in some markets. Some of these battery packs are not adequately protected with internal protection to meet the requirements of appropriate safety standards. There is a possibility that these battery packs may lead to fire or explosion. Please be advised that we are not liable for any accident or failure occurring as a result of use of a counterfeit battery pack. To ensure that safe products are used we would recommend that a genuine Panasonic battery pack is used.

A Tripod receptacle

- 15 -

Charging the battery

Important: Do not use the AC cable with any other equipment as it is designed only for this unit. Also,

do not use the AC cable from other equipment with this unit. It is recommended to charge the battery in a temperature between 10 oC and 30 oC (50 oF

and 86 oF). (The battery temperature should also be the same.)

Insert the plugs as far as they will go.

1 Connect the AC cable to the battery charger and the AC outlet. 2 Insert the battery into the battery charger by aligning the arrows.

We recommend using Panasonic batteries (l 18). If you use other batteries, we cannot guarantee the quality of this product. Do not heat or expose to flame. Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with

doors and windows closed.

When this unit is purchased, the battery is not charged. Charge the battery fully before using this unit for the first time.

Charging lamp [CHARGE] A Lights up: Charging (Battery charging time: l 18) Goes off: Charging completed Flashing: Be sure to connect the unit correctly (l 196)

Power lamp [POWER] B This will light up when the AC cable is

connected.

- 16 -

Inserting/removing the battery 1 Slide the open/close lever, and open the battery cover.

2 Install the battery by inserting it in the direction shown in the figure.

Insert the battery until it clicks and locks.

3 Close the battery cover. Close the battery cover until it clicks and locks.

Removing the battery Make sure that the power switch is set to OFF and the status indicator is turned off, and then remove by holding onto it taking care not to drop. (l 23) Open the battery cover, and slide the battery release lever. The battery will be unlocked, allowing you to take it out. Slide the battery release lever in the direction indicated by the arrow.

- 17 -

Charging and recording time

The times given apply when the ambient operating temperature is 20 oC (68 oF) and the relative operating humidity is 60%. Charging time may be longer at other temperatures and humidity levels.

The continuous recordable time given applies under the conditions below. The time becomes shorter under other conditions. j The LCD monitor is open j A cable is not inserted to the external output terminal

h is an abbreviation for hour, min for minute and s for second. These times are approximations. The indicated charging time is for when the battery has been discharged completely.

Charging time and recordable time vary depending on the usage conditions such as high/ low temperature.

The batteries heat up after use or charging. This is not a malfunction.

Charging/Recording time

Battery model number Voltage/Capacity (minimum) Charging time Continuously recordable

time

Supplied battery/ VW-VBD58 (optional) 7.2 V/5800 mAh 380 min 150 min

- 18 -

You can check the remaining power of the battery by looking at the battery capacity indication displayed on this unit's screen or by looking at the supplied battery VW-VBD58.

Checking the remaining power using this unit

Depending on the menu setting, the battery capacity indication is not displayed (l 174) [DISP SETUP]#[CARD & BATTERY]

Checking the remaining power using the battery If you press the CHECK button, the remaining power indicator (LED lamp) lights up green, allowing you to check the remaining power of the battery.

A CHECK button B Remaining power indicator The remaining power of the battery is an approximate guide. When the LED lamp does not light up even if you press the CHECK button, the battery is

exhausted. Charge the battery.

How to read the remaining power indicator :Lit up/ :Off

The display of the remaining power indicator is an approximate guide for the remaining power of the battery. When the battery pack is connected to the video camera or the charger, refer to the remaining power display of the connected device. The display of the connected device may differ from that of the battery packs remaining power indicator.

Checking the remaining power of the battery

Battery capacity indication The display changes as the battery capacity reduces. # # # #

If the battery discharges, then will flash red.

CHECK100%0

LED lamp status Remaining power of the battery 0% to 25% 25% to 50% 50% to 75%

75% to 100%

- 19 -

Connecting to the AC outlet The unit is in the standby condition when the AC adaptor is connected. The primary circuit is always live as long as the AC adaptor is connected to an electrical outlet. Important: Use the supplied AC adaptor. Do not use the AC adaptor of another device. Do not use the AC cable with any other equipment as it is designed only for this unit. Also,

do not use the AC cable from other equipment with this unit.

Even when you use the AC adaptor for recording images, keep the battery connected. This allows you to continue the recording even if a power failure occurs or the AC adaptor is unplugged from the AC outlet by accident.

1 Connect the AC cable to the AC adaptor and the AC outlet.

2 Connect the AC adaptor to the DC input terminal [DC IN].

Make sure to set the power switch to OFF and the status indicator is turned off when disconnecting the AC adaptor. (l 23)

Insert the plugs as far as they will go.

- 20 -

The unit can record motion pictures or still pictures to an SD card.

Cards that you can use with this unit The cards that you can use are correct as of August 2015. We recommend that you use a Panasonic Memory Card.

About the Speed Class ratings for recording motion pictures Depending on [REC MODE] (l 141) and [REC FORMAT] (l 142), the required card differs.

Use a card that meets the following ratings of the SD Speed Class or UHS Speed Class. Use of a non-compatible card may cause recording to stop suddenly.

SD Speed Class and UHS Speed Class are the speed standards regarding continuous writing. To check the class, see the labelled side, etc. of the card.

We recommend that you use an SD card compatible with UHS Speed Class3 when recording in Variable Frame Rate Mode.

* When [UHD 2160/59.94p 150M] or [UHD 2160/50.00p 150M] is selected, an SDXC Memory Card with a capacity of 64 GB or more and a Speed Class rating of UHS Speed Class3 is required.

Preparation

Preparation of SD cards

Card type Capacity SDHC Memory Card 4 GB to 32 GB SDXC Memory Card 48 GB to 128 GB

When using an SDHC Memory Card/SDXC Memory Card with other equipment, check the equipment is compatible with these Memory Cards.

We do not guarantee the operation of SD cards other than the ones above. 4 GB or more Memory Cards that do not have the SDHC logo or 48 GB or more Memory Cards

that do not have the SDXC logo are not based on SD Memory Card Specifications. This unit is compatible with UHS-I UHS Speed Class3 standard SDHC/SDXC Memory Cards. When the write-protect switch A on SD card is locked, no recording,

deletion or editing will be possible on the card. Keep the Memory Card out of reach of children to prevent swallowing.

Recording modes Bit rates in [REC FORMAT] Speed Class ratings Label examples

MOV/MP4

100 Mbps or more UHS Speed Class3*

50 Mbps

UHS Speed Class1 or more

Class10 or more

AVCHD All Class4 or more

64

- 21 -

Inserting/removing an SD card

Caution: Check that the access lamp has gone off.

1 Open the SD card slot cover and insert (remove) the SD card into (from) the card slot B.

One SD card can be inserted into each of the card slot 1 and the card slot 2.

Face the terminal side C in the direction shown in the illustration and press it straight in as far as it will go.

Press the center of the SD card and then pull it straight out.

2 Securely close the SD card slot cover.

Do not touch the terminals on the back of the SD card.

Do not apply strong shocks, bend, or drop the SD card.

Electrical noise, static electricity or the failure of this unit or the SD card may damage or erase the data stored on the SD card.

When the card access lamp is lit, do not: j Remove the SD card j Turn the unit off j Insert and remove the USB Cable j Expose the unit to vibrations or shock Performing the above while the lamp is on may result in damage to data/SD card or this unit.

Do not expose the terminals of the SD card to water, dirt or dust.

Do not place SD cards in the following areas: j In direct sunlight j In very dusty or humid areas j Near a heater j Locations susceptible to significant

difference in temperature (condensation can occur.)

j Where static electricity or electromagnetic waves occur

To protect SD cards, return them to their cases when you are not using them.

About disposing of or giving away the SD card. (l 196)

When using an SD card for the first time, it is necessary to format the SD card. (l 32) When the SD card is formatted, all of the recorded data is deleted. Once the data is deleted, it cannot be restored.

Access lamp A When this unit is accessing the SD card,

the access lamp lights up.

- 22 -

Set the power switch to ON while pressing the lock release button B to turn on the unit.

A The status indicator lights on.

To turn on the unit again after the [ECONOMY (BATT)] or [ECONOMY (AC)] is activated, set the power switch to OFF once, and then to ON again. (l 177)

Press the THUMBNAIL button to change the mode to Recording Mode or Playback Mode.

When you turn on this unit, it starts up in Recording Mode. If you press the recording start/stop button or sub recording start/stop button in Playback Mode,

the mode will be switched to Recording Mode and recording will start.

Preparation

Turning the unit on/off

Preparation

Selecting a mode

Recording Mode (l 33, 34) The recording screen is displayed. You can record motion pictures and still pictures.

Playback Mode (l 101) The thumbnail screen for playback is displayed. You can play back motion pictures and still pictures.

ON OFF

To turn off the unit Set the power switch to OFF while pressing the lock release button. The status indicator goes off.

A THUMBNAIL button

- 23 -

Setting how to turn on/off the LCD monitor and Viewfinder Select the menu. (l 30)

To change the setting with a USER button You can change how to turn on/off the LCD monitor and Viewfinder by registering LCD/EVF Output to a USER button. Please refer to page 74 for details about setting the USER button. When the recording screen is displayed, press the USER button to which [LCD/ EVF OUTPUT] is registered or touch the applicable USER button icon. Switches the setting each time the button is pressed.

[AUTO] # [LCD] # [EVF] The setting is also applied to the [LCD/EVF OUTPUT] menu setting.

The viewfinder turns on as soon as [EVF] is selected and stays on. It reacts to the eye sensor and turns on/off only after you move your eye closer to the eye cup of the viewfinder.

Depending on the shape of your glasses or the way you hold this unit, or when bright light enters the eyepiece, the eye sensor may not work correctly.

You can turn on/off the viewfinder by registering [EVF ON/OFF] to a USER button.

Using the LCD monitor 1 Extract the LCD monitor in the

direction as indicated in the figure. Hold the LCD monitor extract part A, and

extract the LCD monitor until it clicks into position.

Preparation

Using the LCD monitor/Viewfinder

: [OUTPUT SETUP] # [LCD/EVF OUTPUT] # desired setting

[AUTO]: The LCD monitor is turned on when the LCD monitor is extracted. When you move your eye closer to the eye cup of the viewfinder, the LCD monitor is turned off, and the viewfinder is turned on.

[LCD]: The LCD monitor is turned on when the LCD monitor is extracted. The viewfinder is not turned on.

[EVF]: The viewfinder turns on when you move your eye closer to the eye cup of the viewfinder and turns off when you move your eye away from it. The LCD monitor does not turn on.

MENU

- 24 -

2 Rotate to the position that is easy to view.

How to use the touch screen You can operate by directly touching the LCD monitor (touch screen) with your finger.

Touch Touch and release the touch screen to select icon or picture. Touch the center of the icon. Touching the touch screen will not operate while you

are touching another part of the touch screen.

Slide while touching Move your finger while pressing on the touch screen.

To retract the LCD monitor Retract as shown in the figure with the LCD facing downward.

Range of rotation of the LCD monitor It can rotate up to 270o towards the lens.

270

- 25 -

About the operation icons / / / :

Touch when changing a page or performing settings.

Do not touch the LCD monitor with hard pointed tips, such as ball point pens.

LCD monitor adjustment These settings will not affect the images actually recorded.

Brightness of the LCD monitor can be switched. Select the menu. (l 30)

[LOW] is selected when: j [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

When the [LCD/EVF OUTPUT] is set to [EVF], this item cannot be set. (l 24)

It adjusts brightness and color density on the LCD monitor. 1 Select the menu. (l 30)

2 Touch the desired setting item.

3 Touch / to adjust settings. You can select a value between s16 and r16. 4 Touch [RETURN]. Touch [EXIT] to exit the menu screen.

When the [LCD/EVF OUTPUT] is set to [EVF], this item cannot be set. (l 24)

[LCD BACKLIGHT]

: [DISP SETUP] # [LCD BACKLIGHT] # desired setting

[HIGH]/[LOW]

[LCD SET]

: [DISP SETUP] # [LCD SET]

[COLOR]: Color level of the LCD monitor

[BRIGHTNESS]: Brightness of the LCD monitor

[CONTRAST]: Contrast of the LCD monitor

MENU

MENU

- 26 -

Viewfinder adjustment These settings will not affect the images actually recorded.

It adjusts the field of view to show the image on the viewfinder clearly. 1 Adjust the viewfinder to suit your vision so

that you can see the display images clearly. Be careful not to trap your fingers when moving the

viewfinder. The viewfinder can be lifted vertically up to

approximately 90o. Turn on the viewfinder. 2 Adjust the focus by operating the eyepiece

corrector lever.

It adjusts brightness and color density of the viewfinder. Use the jog dial to change the settings. (l 98) 1 Select the menu. (l 30)

2 Rotate the jog dial to move the cursor to the value display A.

Push the jog dial to select the value display. 3 Rotate the jog dial to adjust the setting. Pushing the jog dial will set the value you have selected. You can select a value between s16 and r16. 4 Select [RETURN]. Select [EXIT].

When the [LCD/EVF OUTPUT] is set to [LCD], this item cannot be set. (l 24) When [COLOR] is set to s16, images are displayed in black and white.

Adjusting the field of view

[EVF SETTING]

: [DISP SETUP] # [EVF SETTING] # desired setting

[COLOR]: Color level of the viewfinder

[BRIGHTNESS]: Brightness of the viewfinder

[CONTRAST]: Contrast of the viewfinder

A Eyepiece corrector lever

MENU

- 27 -

The recording images or playback images on the viewfinder can be selected between color/black and white. Select the menu. (l 30)

If you adjust the [COLOR] setting in [EVF SETTING], [EVF COLOR] will be set to [ON].

It adjusts sensitivity of eye sensor. 1 Select the menu. (l 30)

2 Touch / to adjust settings. You can select a value between s4 and r4. 3 Touch [EXIT] to complete the setting.

When the [LCD/EVF OUTPUT] is set to [LCD], this item cannot be set. (l 24)

Recording yourself Change the mode to Recording Mode. (l 23) Rotate the LCD monitor towards the lens side. Displaying during the recording yourself can be

switched by setting [SELF SHOOT]. (l 175)

Only some indications will appear on the screen when the [SELF SHOOT] is set to [MIRROR]. When appears, return the direction of the LCD monitor to normal position and check the warning/alarm indication. (l 185)

The LCD monitor display changes as follows when Self Shoot is used: j The viewfinder image is displayed. j The display size becomes smaller.

[EVF COLOR]

: [DISP SETUP] # [EVF COLOR]# [ON] or [OFF]

[ON]: Displayed in color

[OFF]: Displayed in black and white

[EYE SENSOR]

: [DISP SETUP] # [EYE SENSOR]

MENU

MENU

- 28 -

When this unit is turned on, the message [SET TIME ZONE AND DATE/TIME] may appear. To make these settings, select [YES], and follow the instructions from Step 2-3 of the time zone setting procedure.

1 Select the menu. (l 30)

2 Touch the date or time to be set, then set the desired value using / .

The year can be set between 2000 and 2039.

3 Touch [EXIT] to complete the setting.

The date and time function is driven by a built-in lithium battery. If the time display becomes [- -], the built-in lithium battery needs to be charged.To recharge the

built-in lithium battery, connect the AC adaptor or attach a charged battery to this unit. Leave the unit as it is for approx. 24 hours and the battery will maintain the date and time for approx. 6 months. (The battery is still being recharged even if the unit is off.)

The way that time is displayed can be changed in the menu settings. (l 173) [DISP SETUP] # [DATE/TIME] or [DATE FORMAT]

Time difference from the Greenwich Mean Time can be set. 1 Select the menu. (l 30)

2 Touch / and set the region to record. 3 Touch [EXIT] to complete the setting. If the [CLOCK SET] screen appears, perform [CLOCK SET].

When the time zone setting is changed, the date/time setting of the unit also changes automatically.

Preparation

Setting date and time

: [OTHER FUNCTION] # [CLOCK SET]

Time zone

: [OTHER FUNCTION] # [TIME ZONE]

MENU

MENU

- 29 -

You can also select menu items by operating the jog dial. (l 98)

1 Press the MENU button . 2 Touch the top menu A.

3 Touch the submenu B. Next (Previous) page can be displayed by touching /

.

4 Touch the desired item to enter the setting. 5 Touch [EXIT] to exit the menu setting.

Preparation

Using the menu screen

MENU

MENU

- 30 -

When recording, make sure your footing is stable and there is no danger of colliding with another person or object.

Hold the eye cup of the viewfinder as close as possible to your eye. Adjust the angle of the LCD monitor according to the position in which the unit is held. When you are outdoors, record pictures with the sunlight behind you. If the subject is backlit, it will

become dark in the recording. Keep your arms near your body and separate your legs for better balance. For stable images, it is recommended to use a tripod whenever possible. Do not block the cooling fan inlet or the exhaust opening with your hand or other objects.

When recording to the SD card with this unit, set [OUTPUT BITS] to [4:2:2(8bit)]. When recording with an external device connected via the HDMI OUT/SDI OUT terminal, you can change the picture quality of images output to the device by changing the [OUTPUT BITS] setting.

Select the menu.

When [4:2:2(10bit)] is selected, and are displayed on the screen. The setting method of the picture quality of the image changes depending on the [OUTPUT BITS]

setting. j When [4:2:2(10bit)] is selected, change the [OUTPUT FORMAT] setting. (l 147) j When [4:2:2(8bit)] is selected, change the [REC MODE] and [REC FORMAT] settings. (l 141,

142)

This function is not available in the following cases: j During Freeze Frame (l 81) j In Variable Frame Rate Mode (l 91)

The following menu items are not available when [4:2:2(10bit)] is selected: j [VFR MODE] (l 91, 131) j [REC MODE] (l 141) j [REC FORMAT] (l 142) j [SUB REC BUTTON] (l 156) j [2 SLOTS FUNC.] (l 159) j [DUAL CODEC REC] (l 161)

j [INTERVAL REC] (l 162) j [PRE-REC] (l 86, 163) j [TIME STAMP] (l 164) j [DOWN CONV.] (l 169) j [VIDEO OUT OSD] (l 115) j [MEDIA SELECT] (l 32) j [MEDIA STATUS] (l 176)

Recording

Before recording

Recording

Selecting the Recording Method

: [SYSTEM MODE]# [OUTPUT BITS] # desired setting

[4:2:2(10bit)]: Allows you to output high quality images using an HDMI/SDI connection. This setting is suitable for recording with an external device that supports HDMI/SDI output. You cannot record these images with this unit.

[4:2:2(8bit)]: Allows you to output the image being recorded with this unit.

MENU

4:2:2 10bit REC

- 31 -

The following functions are not available when [4:2:2(10bit)] is selected:

j [DIGITAL ZOOM] (l 79) j [REC CHECK] (l 80)

j [LAST SCN DEL] (l 80)

Formatting media If you use the SD cards for the first time for recording with this unit, format the cards. Please be aware that if a medium is formatted, then all the data recorded on the medium will be erased and cannot be restored. Back up important data on a PC etc. (l 121) When using two SD cards, format both SD cards.

1 Select the menu.

2 Touch [SD CARD 1] or [SD CARD 2]. When formatting is complete, touch [EXIT] to exit the message screen.

Do not turn this unit off or remove the SD card, while formatting. Do not expose the unit to vibrations or shock.

[SD CARD 1] and [SD CARD 2] can be selected separately to record motion pictures or still pictures. Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31)

1 Select the menu.

2 Touch the media to record motion pictures or still pictures.

The media is selected separately for motion pictures or still pictures and is then highlighted in yellow.

3 Touch [EXIT] to complete the setting.

: [OTHER FUNCTION] # [FORMAT MEDIA]

Use this unit to format media. Do not format an SD card using any other equipment such as a PC. Otherwise it may not be possible to use the card on this unit.

Recording

Selecting a media to record

: [RECORD SETUP] # [MEDIA SELECT]

MENU

MENU

- 32 -

Before turning on this unit, open the lens cover. (l 12) Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31)

1 Change the mode to Recording Mode. (l 23)

Extract the LCD monitor.

2 Press the recording start/ stop button B to start recording.

Recording will stop when you press the recording start/stop button again.

Screen indications in the Recording Mode

To change the recording method, change [REC MODE] or [REC FORMAT]. (l 141, 142) The images recorded between pressing the recording start/stop button to start recording and

pressing it again to pause recording become one scene. When the file size of a recorded scene exceeds one of the following sizes or the recording time

exceeds one of the following lengths of time, the scene will be divided automatically. (Recording continues.) j AVCHD scene: approximately 4 GB j MOV/MP4 scene (when using an SDHC Memory Card): approximately 4 GB or 30 minutes j MOV/MP4 scene (when using an SDXC Memory Card): approximately 48 GB or 120 minutes

Recording

Recording motion picture with this unit

ON OFF

REC

A When you begin recording, REC (red) is displayed.

TC 00:00:00.00

59.94p 150M

R 1h20m

TC 00:00:00.00 Counter display (l 70) (White) Media where the motion picture is

recorded (l 32) R 1h20m Approximate remaining recordable

time When the remaining time is less

than 1 minute, R 0h00m flashes red.

Recording format (l 142)

150M Bit rate (l 142) Recording mode (l 141)

59.94p Frame rate (l 142)

- 33 -

Number of scenes that can be recorded will be less than above in following cases: j If you change [REC FORMAT] (l 142) j When [2 SLOTS FUNC.] is set to [SIMULTANEOUS] or [DUAL CODEC] (l 159) j During the Interval Recording (l 162)

Please refer to page 200 about approximate recordable time.

Before turning on this unit, open the lens cover. (l 12) Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) Register [CAPTURE] to a USER button. (l 74)

1 Change the mode to Recording Mode. (l 23) Extract the LCD monitor.

2 Press the USER button to which [CAPTURE] is registered or touch the applicable USER button icon to record a still picture.

For information on the locations of the USER buttons and information on USER button icons, refer to page 74.

When still pictures are being recorded, the remaining recordable number of still pictures and the still picture indication are displayed.

About the screen indications while recording still pictures

(Maximum recordable scenes of a single SD card)

Recording mode MOV/MP4 AVCHD

Recordable scenes Approx. 89100 Approx. 3900

Different dates (l 108) Approx. 900 Approx. 900

When the SD card contains scenes recorded with [REC MODE] set to [MOV]/[MP4] and still pictures, the maximum recordable scenes and the maximum recordable scenes on each date will be smaller than those in the table above.

Recording

Recording still pictures

Size of still pictures

R3000 Remaining number of still pictures Still picture indication (l 183)

R3000M8.3

M8.3

- 34 -

About picture size Picture sizes in which still pictures will be recorded differ depending on the [REC MODE] setting and the [REC FORMAT] setting (l 141, 142).

It is possible to record still pictures while recording motion pictures. (rec-and-capture) It is recommended to use a tripod when recording under low light conditions because the shutter

speed becomes slow. If rec-and-capture is used while recording a motion picture, the remaining recordable time will

shorten. If you turn off this unit or press the THUMBNAIL button, the remaining recordable time may become longer.

Maximum number of recordable pictures that can be displayed is 9999. If the number of recordable pictures exceeds 9999, R 9999+ is displayed. The number will not change when the picture is taken until the number of recordable pictures is 9999 or less.

When playing back a still picture recorded with this unit in the 17:9 aspect, black bands appear on the top and bottom of the screen.

The 17:9 or 16:9 still pictures recorded using this unit may be cropped at the edges when printed. So, be sure to check before printing in the store or on your printer.

Please refer to page 202 about approximate number of recordable pictures. The recording time may be long depending on the recording condition.

Recording mode Recording format Aspect Picture size

MOV, MP4

[REC FORMAT] setting with a size of 4K (4096k2160) 17:9 4096k2160

[REC FORMAT] setting with a size of UHD (3840k2160)

16:9

3840k2160

[REC FORMAT] setting with a size of FHD (1920k1080)

1920k1080

AVCHD

[PS 1080/59.94p], [PS 1080/50.00p], [PH 1080/59.94i], [PH 1080/23.98p], [PH 1080/50.00i], [HA 1080/59.94i], [HA 1080/50.00i], [HE 1080/59.94i], [HE 1080/50.00i], [PM 720/59.94p], [PM 720/50.00p],

[SA 480/59.94i], [SA 576/50.00i] 640k360

4:3 640k480

M8.8

M8.3

2.1 M

M0.2

0.3M

- 35 -

is displayed in the Auto Mode.

Auto Mode In Auto Mode, this unit operates according to the [AUTO SW] menu settings. When the following settings are automatically adjusted in Auto Mode, the corresponding Manual

Mode settings are canceled:

j Focus (l 44) j Iris (l 59)

j Shutter speed (l 63)

To enable/disable auto switch functions You can enable/disable functions that are automatically adjusted in Auto Mode.

Select the menu.

Recording

Switching between Auto and Manual Mode

AUTO/MANU switch Slide the switch to change Auto Mode/Manual Mode.

MANU

: [AUTO SW] # desired settingMENU

- 36 -

Automatic Tracking White Balance The Auto Tracking White (ATW) Balance function of this unit automatically adjusts the White Balance according to the lighting condition. If the Automatic White Balance is not functioning normally, adjust the White Balance manually. (l 55)

Auto Focus The unit focuses automatically. Auto Focus does not work correctly in the following situations. Record pictures in the Manual

Focus Mode. (l 44) j Recording distant and close-up objects at the same time j Recording a subject behind dirty or dusty window j Recording a subject that is surrounded by objects with glossy surfaces or by highly reflective

objects

Menu item Setting

[A.IRIS] [ON]: Activates Auto Iris in Auto Mode.

[OFF]: Activates Auto Iris as a manual mode. Use the IRIS button to switch between Auto Iris Mode and Manual Iris Mode.

[AGC] [ON]: Activates Auto Gain in Auto Mode. [OFF]: Activates Auto Gain as a manual mode. The gain is adjusted

according to the settings assigned to the GAIN switch.

[AUTO SHUTTER]

[ON]: Activates Auto Shutter in Auto Mode.

[OFF]: Activates Auto Shutter as a manual mode. Press the SHUTTER button to switch between Auto Shutter Mode and Manual Shutter Mode.

[ATW]

[ON]: Activates Auto Tracking White Balance in Auto Mode.

[OFF]: Activates Auto Tracking White Balance as a manual mode. The white balance is adjusted according to the setting registered to the WHITE BAL switch.

[AF] [ON]: Activates Auto Focus in Auto Mode.

[OFF]: Activates Auto Focus as a manual mode. Focus is adjusted according to the functions of the FOCUS A/M/ switch.

- 37 -

Controls that are disabled in Auto Mode Certain controls of this unit may be disabled in Auto Mode. Controls to be disabled vary by the [AUTO SW] menu settings.

You can set the picture quality of images to be recorded in the main menu # [SCENE FILE].

This function thickens or weakens the outlines of images. It effectively softens or sharpens images, but in some cases, the whole image may become rough due to emphasized noise and edges. To avoid such problems, it is necessary not to add this effect on parts where emphasizing is not needed and keep the details of the parts.

Menu item

This function makes human skin look smoother in images.

Menu item [SKIN TONE DTL] (l 133)

This function makes settings to add or reduce intensity of red and blue colors according to the position of the WHITE BAL switch. The function works when the switch is at the [PRST] position or when Automatic White Balance is enabled. It does not work with Auto Tracking White Balance.

Conditions that disable controls Controls that are disabled in Auto Mode

[A.IRIS] is set to [ON]. Iris Ring, IRIS button

[AGC] is set to [ON]. GAIN switch, the USER button to which [SUPER GAIN] is registered

[AUTO SHUTTER] is set to [ON]. SHUTTER button

[ATW] is set to [ON]. WHITE BAL switch

[AF] is set to [ON]. Focus ring, FOCUS ASSIST button, FOCUS A/M/ switch, PUSH AUTO button, the USER button to which [FOCUS TRANSITION] is registered

Recording

Adjusting the Picture Quality

Detail function

[MASTER DETAIL]: Adjusts the degree of overall outline correction in images. (l 132) [DETAIL CORING]: Adjusts the detail noise removal level. (l 133) [SKIN TONE DTL]: Makes skin colors appear softer for a more attractive appearance.

(l 133) [V DETAIL LEVEL]: Adjusts the degree of vertical outline correction in images. (l 133) [KNEE APE LEVEL]: Sets the detail level of high luminosity areas (extremely bright areas).

(l 134)

Skin tone function

RB gain control function

- 38 -

Menu item [RB GAIN CONTROL SETTING] (l 134)

This function sets color saturation and phase. It applies effects on whole images. It cannot be set to individual color hue.

Menu item

This function sets color saturation and phase. It applies individual effect on 16 phases in an image. It can be set to individual color hue.

Menu item [COLOR CORRECTION SETTING] (l 136)

This function sets the black level that is to be the reference of luminance.

Menu item [MASTER PED] (l 137)

This function optimizes the tone of images.

Menu item

This function sets the compression of video signals to prevent white saturation in images.

Menu item

Chroma setting function

[CHROMA LEVEL]: Adjusts the color density. (l 135) [CHROMA PHASE]: Adjusts the color balance. (l 135)

Color correction function

Black control function

Gamma function

[GAMMA MODE]: Sets the optimal tone and contrast of images for the scene to be recorded. (l 137)

[BLACK GAMMA]: Sets the gamma curve for dark areas.(l 138) [BLACK GAMMA RANGE]: Sets the upper limit on the compression/expansion of the

[BLACK GAMMA] setting. (l 138)

Knee function

[KNEE MODE]: Sets the compression level of highly bright image signals received by the image sensor to minimize white saturation. (l 138)

[KNEE MASTER POINT]: Adjusts the knee point position in 0.5% steps. (l 138) [KNEE MASTER SLOPE]: Sets the knee inclination. (l 139)

- 39 -

It can be zoomed up to 13k. (When the picture size of [REC FORMAT] (l 142) or [OUTPUT FORMAT] (l 147) is

1920k1080 or below) It can zoom up to approx. 20k when the [i.Zoom] is set to [ON]. (l 157)

It is possible to change the unit of the zoom magnification display by changing the [ZOOM/ FOCUS] setting. The setting can also be changed so that the display disappears from the screen. (l 173)

When [FOCUS MACRO] is set to [OFF], subjects at a distance of approximately 1.0 m (3.3 feet) to infinity can be brought into focus. When [FOCUS MACRO] is set to [ON] and the zoom position is at the W end, subjects at a distance of approximately 10 cm (3.93 q) to infinity can be brought into focus. (l 94, 154)

1 Slide the ZOOM switch.

2 (Set the ZOOM switch to [MANU]) Operate the zoom ring.

(Set the ZOOM switch to [SERVO]) Operate the zoom lever/sub zoom lever.

Recording

Using the zoom

MANU: Zoom operation can be done using the zoom ring. SERVO: Zoom operation can be done using the zoom lever/sub zoom lever.

Zoom ring A A side: Wide-angle recording (zoom out) B side: Close-up recording (zoom in)

T side: Close-up recording (zoom in) W side: Wide-angle recording (zoom out)

T

W

T

W

ZOOM MANU SERVO

A Zoom ring B Zoom switch C Zoom lever D Sub zoom lever

A

B

- 40 -

If you take your finger off the zoom lever during zoom operation, the operation sound may be recorded. When returning the zoom lever to the original position, move it quietly.

When [i.Zoom] is set to [ON], you can zoom in while maintaining the beauty of high-definition picture quality up to a magnification of approx. 20k. Set [REC FORMAT] or [OUTPUT FORMAT] to a setting with a picture size of 1920k1080 or

below. (l 142, 147)

1 Select the menu.

The zoom magnification display will change.

* You can select a value between 1.00 and 1.54. If you touch the screen, i.Zoom button icons are displayed.

2 Touch the i.Zoom button icons ( / ) to change the i.Zoom magnification.

You can use i.Zoom by registering [i.Zoom] to a USER button. (l 74) This function is not available in the following cases:

j In Variable Frame Rate Mode (l 91) j When [REC FORMAT] or [OUTPUT FORMAT] is set to a setting with a size of 4K (4096k2160)

or UHD (3840k2160) j During Freeze Frame (l 81)

[i.Zoom] is canceled in the following cases. j If you turn the unit off j If you press the THUMBNAIL button j When [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

When [FAST ZOOM] is set to [ON], you can use Fast Zoom while operating the zoom with the zoom lever.

1 Select the menu.

2 Push the zoom lever fully to operate the zoom. The zoom magnification display changes when using Fast Zoom. (Example: 99)

Adjusting the i.Zoom magnification

: [SW SETUP] # [i.Zoom] # [ON]

(Example)

A Zoom magnification B i.Zoom magnification*

C i.Zoom button icons D Zoom magnification

Using Fast Zoom

: [SW SETUP] # [FAST ZOOM] # [ON]

MENU

iZ99 1.00

SCN1 SCN2 SCN3 SCN4 SCN5 SCN6

MENU iZ99 1.00W

i.Zoom T

i.Zoom

ATW DRS PRE-REC

MENU

- 41 -

About the zoom speed The zoom speed will vary depending on how far the zoom lever is pressed or how fast the zoom

ring is rotated. The zoom operation using the sub zoom lever will be performed at a constant speed. Zoom

speed of the sub zoom lever will vary depending on the setting of [SUB ZOOM]. (l 156)

You can also use Fast Zoom by registering [FAST ZOOM] to a USER button. (l 74) The sound of the zoom mechanism becomes louder than usual during fast zoom operation. This

may cause the sound to be recorded during recording.

Utilizing the USER button Digital zoom can be used by setting the USER button. (l 79) Please refer to page 74 for details about setting the USER button.

Use the Image Stabilizer to reduce the effects of shake during recording. This unit is equipped with Hybrid Optical Image Stabilizer. Hybrid Optical Image Stabilizer is a hybrid of Optical and Electrical Image Stabilizer.

1 Register O.I.S. to a USER button. (l 74) This function is registered to the USER5 button by default.

2 Press the USER button to which [O.I.S.] is registered or touch the applicable USER button icon to switch the Image Stabilizer on/off.

You can also access this function by selecting menu items. [SW SETUP] # [O.I.S.] # [ON]/[OFF]

When [HYBRID O.I.S.] is [ON], is displayed. When [OFF], is displayed. This item cannot be set during Freeze Frame (l 81)

Changing Image Stabilizer Mode Select the menu.

When set to [ON], you can further improve image stabilization for holding the unit and recording a distant subject with zoom. Optical Image Stabilizer will be disabled and the setting cannot be changed in the following

cases: j When Optical Image Stabilizer is set to (setting canceled) j When the size is set to 4K (4096k2160) or UHD (3840k2160) in [REC FORMAT] or [OUTPUT

FORMAT] (l 142, 147) j During Freeze Frame (l 81) j In Variable Frame Rate Mode (l 91)

Recording

Image Stabilizer Function

/ # (OFF)

: [SW SETUP] # [HYBRID O.I.S.] # [ON] or [OFF] MENU

- 42 -

Stabilization may not be possible under strong shaking conditions. When using a tripod, we recommend that you set the Image Stabilizer to (setting canceled).

You can customize the Image Stabilizer by adjusting the [BLUR AMPLITUDE] and [BLUR FREQUENCY] settings individually.

Custom Optical Image Stabilizer When [ON] is selected, the Image Stabilizer works with customized [BLUR AMPLITUDE] and [BLUR FREQUENCY] settings.

Select the menu.

Blur amplitude You can adjust the performance of camera shake correction according to the level of camera shake during recording.

Select the menu.

If you set a smaller value, correction performance against minor camera shake will be enhanced. Even though smaller values allow more effective screen stabilization in situations with minor camera shake, such as when you are recording from a fixed position, they are less effective for correcting significant camera shake. We recommend setting a smaller value when you keep recording the same subject, for example.

If you set a larger value, camera shake of varying degrees ranging from minor to significant will be corrected in a balanced manner. Although larger values allow you to correct significant camera shake more effectively, the screen becomes unstable when you are recording from a fixed position. We recommend that you set a larger value in situations where images are expected to be quite blurry, such as when recording in an unstable position.

Blur frequency You can change the target frequency range for camera shake correction to adjust its performance according to the recording style.

Select the menu.

Customizing the Image Stabilizer for various recording conditions

: [SW SETUP] # [CUSTOM O.I.S.] # [ON]

: [SW SETUP] # [BLUR AMPLITUDE] # desired setting

[1]/[2]/[3]/[4]/[5]

: [SW SETUP] # [BLUR FREQUENCY] # desired setting

[1]: This enhances the correction performance against camera shake of varying degrees, ranging from slow camera shake that falls in the low frequency range to fast and subtle camera shake that falls in the high frequency range. We recommend that you select this setting when recording a subject from a fixed position without panning or tilting this unit.

[2]: This is a standard setting which enhances the correction performance against camera shake that falls in the average-to-high frequency range. Even while adjusting the position of this unit, you can keep the resulting motion in the image look natural and maintain the correction performance.

MENU

MENU

MENU

- 43 -

Perform focus adjustments using the focus ring. If auto focusing is difficult due to the conditions, then use Manual Focus.

Switch to Manual Mode. (l 36)

1 Set the FOCUS A/M/ switch to [M] to enable Manual Focus. It will switch to MF from AF.

2 Adjust the focus by rotating the focus ring. The focus value can be set from MF00 (focus distance: approximately 10.0 cm (3.93 q) [When

[FOCUS MACRO] (l 94, 154) is set to [ON]]) to MF99 (focus distance: infinity). The larger the focus value gets, the further the position where focus is achieved.

If you move the FOCUS A/M/ switch towards [], focus will be adjusted to MF95 on the infinity side. (The FOCUS A/M/ switch will return to the [M] position.)

To return to Auto Focus, set the FOCUS A/M/ switch to [A], or set [AF] to [ON] and switch to Auto Mode. (l 36)

If you set [FOCUS MACRO] to [ON], when the distance to the subject approaches within 0.8 m (2.6 feet) approx., the unit switches to the macro range and or . (The unit may switch to the macro range even when the distance to the subject is 0.8 m (2.6 feet) or more depending on the subject.).

Depending on the zoom magnification, this unit may fail to switch to the macro range, or go to a non-displayed focus value.

When you perform a zoom operation in the macro range, this unit may go out of focus. When [AF] is set to [ON] and this unit is set to Auto Mode, auto focusing is performed regardless

of the position of FOCUS A/M/ switch. (l 36) When a remote control (commercially-available) is connected, even if you move the FOCUS A/M/

switch towards [], focus cannot be adjusted to MF95. (l 113) The unit of the focus value display differs depending on the [ZOOM/FOCUS] setting. The setting

can also be changed so that the display disappears from the screen. (l 173)

[3]: This mainly enhances the correction performance against fast and subtle camera shake that falls in the high frequency range while weakening the correction performance against slow camera shake that falls in the low frequency range. We recommend that you use this setting when panning or tilting this unit many times while recording.

Recording

Focus

A FOCUS A/M/ switch B PUSH AUTO button C Focus ring

PUSH AUTO

FOCUS

A M

- 44 -

To change the way you adjust focus with the focus ring Select the menu.

To emphasize the outline of images Setting [EVF/LCD DETAIL] to [ON] helps you achieve focus easier by emphasizing the outlines of an image displayed on the LCD monitor and viewfinder. You can also adjust the emphasis level or change the frequency. You can also enable or disable this function with the applicable USER button. (l 83) These settings will not affect the images actually recorded.

Adjusting the level of [EVF/LCD DETAIL] 1 Select the menu.

2 Touch / to adjust settings. You can select a value between s3 and r3. 3 Touch [EXIT] to complete the setting. Setting the peaking frequency of [EVF/LCD DETAIL] Select the menu.

[EVF/LCD DETAIL] is canceled in following cases: j If you use Focus Assist (l 48)

: [SW SETUP] # [FOCUS RING DRIVE]

[SPEED]: Adjusts the focus value according to the speed at which the focus ring is rotated.

[COARSE]: Adjusts the focus value according to the rotational position of the focus ring. Since the operation of the focus ring results in a greater change in focus value, this setting is suitable for making rough adjustments.

[FINE]: Adjusts the focus value according to the rotational position of the focus ring. Since the operation of the focus ring results in a smaller change in focus value, this setting is suitable for making fine adjustments.

: [DISP SETUP] # [EVF/LCD DETAIL] # [ON]

: [DISP SETUP] # [EVF/LCD PEAK LEVEL]

: [DISP SETUP] # [EVF/LCD PEAK FREQ.] # [HIGH] or [LOW]

MENU

MENU

MENU

MENU

- 45 -

You can customize Auto Focus for various recording conditions by adjusting the settings of [AF SPEED], [AF SENSITIVITY], and [AF AREA WIDTH] individually.

Custom AF function When [ON] is selected, Auto Focus works with customized [AF SPEED] and [AF SENSITIVITY] settings. Switch to Auto Focus Mode. (l 44) Select the menu.

AF speed setup You can change the focus speed of Auto Focus. Switch to Auto Focus Mode. (l 44) Set [CUSTOM AF] to [ON]. 1 Select the menu.

2 Touch / to adjust settings. You can select a value between j5 and i5. The larger the value is, the faster the focus speed will become. Conversely, the smaller the value

is, the slower the focus speed will become. 3 Touch [EXIT] to complete the setting.

AF Sensitivity setup You can enhance the stability or tracking performance of Auto Focus. Switch to Auto Focus Mode. (l 44) Set [CUSTOM AF] to [ON]. 1 Select the menu.

2 Touch / to adjust settings. You can select a value between 0 and 10. Setting a larger value will enhance the tracking performance of focus, making it easier to move

focus between subjects at varying distances from this unit. We recommend that you set a larger value to keep focus on a fast-moving subject.

Setting a smaller value will provide more stability to focus, making it easier to keep focus on the targeted subject even when an intervening object passes in front of the camera or the subject disappears from the view of this unit. We recommend that you set a smaller value to avoid bringing an intervening object or the background into focus.

3 Touch [EXIT] to complete the setting.

Customizing Auto Focus for various recording conditions

: [SW SETUP] # [CUSTOM AF] # [ON]

: [SW SETUP] # [AF SPEED]

: [SW SETUP] # [AF SENSITIVITY]

MENU

MENU

MENU

- 46 -

[CUSTOM AF], [AF SPEED] and [AF SENSITIVITY] cannot be set in Variable Frame Rate Mode. (l 91)

[AF SPEED] and [AF SENSITIVITY] cannot be set in Manual Focus Mode. When a faster [AF SPEED] value is selected, focus mechanism noise will be more audible. As a

result, the noise may be recorded while recording is in progress.

AF Area Range Adjustment You can adjust the effective area width for Auto Focus according to the size of the subject. Switch to Auto Focus Mode. (l 44) 1 Select the menu.

To cancel the settings, set [AF AREA WIDTH] to [OFF]. If you push the jog dial in Step 2, the AF area frame turns yellow, allowing you to select

[RETURN]/[EXIT] by rotating the jog dial. Push the jog dial to set the selected item. You can also adjust AF area width by registering [AF AREA WIDTH] to a USER button. (l 90) This function is not available in the following cases:

j In manual focus mode (l 44) j When using Area Mode (l 82) j During Freeze Frame (l 81)

One Push AF If you press the PUSH AUTO button in Manual Focus Mode, the camera performs high-speed focusing until the image is focused. Switch to Manual Focus Mode. (l 44) Press PUSH AUTO button. Auto Focus will be activated and the camera will perform high-speed focusing until the image is

focused. The focus setting returns to Manual Focus Mode once the image is focused or a certain time has

elapsed.

: [SW SETUP] # [AF AREA WIDTH] # [SET]

2 Push the jog dial.

3 Rotate the jog dial to adjust the AF area frame.

A [RETURN] B AF area frame C [EXIT] 4 Touch [EXIT] to complete the setting. will be displayed on the screen.

MENU

AF-AREA

- 47 -

Push AF If you press and hold the PUSH AUTO button, Manual Focus will be temporarily switched to Auto Focus. Set this unit to Manual Focus. (l 44) Press and hold the PUSH AUTO button. The focus position will be automatically adjusted for the subject at the center of the screen. If you set [AREA MODE] to [FOCUS], [FOCUS/IRIS] or [FOCUS/Y GET] and use Area Mode, the

focus position will be automatically adjusted to the subject you have touched. (l 82) It will be canceled when the button is released, and the focus position set by the Push AF will be

maintained.

Push AF does not work in following cases: j When Auto Focus is used j When a remote control (commercially-available) is connected (l 113)

Focus Assist Pressing the FOCUS ASSIST button allows you to use Focus Assist.

Select the menu.

You can also use Focus Assist by registering [FOCUS ASSIST] to a USER button. (l 77)

Selecting a Focus Assist method

: [SW SETUP] # [FOCUS ASSIST] # desired setting

[EXPAND]: Magnifies the central area of the screen when Focus Assist is used.

[PEAKING]: Highlights in-focus portions with color when Focus Assist is used.

[BOTH]: Sets both [EXPAND] and [PEAKING].

Using Focus Assist

Switch to Manual Focus Mode. (l 44)

Press the FOCUS ASSIST button. To turn off Focus Assist, perform the following operations:

j Press the FOCUS ASSIST button again. j Touch [EXIT].

MENU

FOCUS ASSIST

- 48 -

To adjust the magnified display When [FOCUS ASSIST] is set to [EXPAND] or [BOTH], the central area of the screen will be magnified. You can change the magnification level and position of the magnified display. You can also change the magnification level of the magnified display using the jog dial.

(To change the magnification level) Touch / or rotate the jog dial to change the magnification level.

You can adjust the magnification from 3k to 10k.

(Moving the magnified area) Touch / / / or slide the screen while touching it to move the magnified area.

To change the peaking settings When [FOCUS ASSIST] is set to [PEAKING] or [BOTH], in-focus portions are highlighted with color. F: Peaking You can set the peaking color and strength.

(When changing the peaking color) Select the menu.

(When setting the peaking strength) 1 Select the menu.

: Increases the magnification level by 0.5k.

: Decreases the magnification level by 0.5k.

x3.0

A 3k5k display B 5.5k10k display C [ASSIST] D Magnified display E [EXIT] F Jog dial

x5.5

: [SW SETUP] # [PEAKING COLOR] # desired color

[Red]/[Blue]/[Yellow]/[White]

MENU

- 49 -

2 Touch / to adjust settings. You can select a value between s7 and r7. 3 Touch [EXIT] to complete the setting.

(Notes on Focus Assist) Focus Assist is not possible in following cases:

j During Recording Check (l 80) j During Freeze Frame (l 81) j When color bars are displayed. (l 95)

Focus Assist is canceled in following cases: j If you turn the unit off j If you press the THUMBNAIL button j When the setting of [FOCUS ASSIST] (l 48) is changed j When EVF/LCD detail is enabled. (l 45) j When you set this unit to Auto Focus j When you press the USER button to which [FOCUS TRANSITION] is registered or touch the

applicable USER button icon (l 53) j When [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

The magnified display and peaking are not displayed on recorded images. The magnified display and peaking are not displayed on an external monitor. Freeze Frame is not available when you use Focus Assist. (l 81) Peaking may not be displayed when you use Digital Zoom (l 79). To zoom in and use peaking at

the same time, we recommend setting [FOCUS ASSIST] to [BOTH] and increasing the magnification level of the magnified display.

(Notes on the magnified display of Focus Assist) Some information on the screen disappears when the screen is magnified. Still pictures cannot be recorded when the screen is magnified. In the following cases, the screen is not magnified during Focus Assist:

j During motion picture recording or PRE-REC (l 86, 163) j When using Digital Zoom j When using Area Mode (l 82) j During auto recording (l 90) j In Variable Frame Rate Mode (l 91)

If you set the magnification level of the magnified display to 5.5k or higher, peaking may not be displayed when using i.Zoom (l 41).

: [SW SETUP] # [PEAKING LEVEL] # desired settingMENU

- 50 -

Manual Focus Assist Focus is automatically adjusted after you adjust it with the focus ring in Manual Focus Mode. Focus may not be achieved when the focus deviation is great. After automatic adjustment is complete, the focus is not adjusted automatically again until you

operate the focus ring. Switch to Manual Focus Mode. (l 44)

1 Select the menu.

Touch [EXIT] to complete the setting. The on-screen icon changes from [MF] to [MA].

2 Adjust the focus by rotating the focus ring. Focus is automatically adjusted after you adjust it with the focus ring. The color of the on-screen icon for the focus value changes during automatic adjustment.

This function is not available in the following cases: j When Auto Focus is used j When using Area Mode (l 82) j In Variable Frame Rate Mode (l 91)

The on-screen icon changes to in the macro range. Manual focus assist does not work in following cases:

j When adjusting the focus with the remote control (commercially-available) (l 113)

To change the Manual Focus Assist setting You can change the way focus is adjusted when Manual Focus Assist is used. Switch to Manual Focus Mode. (l 44)

Select the menu.

Touch [EXIT] to complete the setting.

[MF ASSIST MODE] cannot be set in Auto Focus Mode. It may be easier to see a change in focus when [MULTI AREA] is selected.

We recommend that you adjust focus before recording. Focus may not be achieved depending on the recording condition such as brightness or contrast,

even if [MULTI AREA] is selected. If focus is not achieved within a certain period of time, focus returns to the position before the

automatic adjustment.

: [SW SETUP] # [MF ASSIST] # [ON]

: [SW SETUP] # [MF ASSIST MODE] # desired setting

[CENTER AREA]: Fine-adjusts focus for the subject at the center of the screen.

[MULTI AREA]: Adjusts focus for the subject closest to the current focus position.

MENU

MENU

- 51 -

Focus Transition You can use Focus Transition by registering Focus Transition to a USER button. With Focus Transition, you can shift the current focus position to a pre-registered focus position. Please refer to page 74 for details about setting the USER button.

To use Focus Transition, you need to register a focus position. You can register up to 3 focus positions. Switch to Manual Focus Mode. (l 44)

1 Select the menu.

2 Touch the item to which you want to register the focus position.

You can select the item by pressing the USER buttons 1-3. The Focus Assist screen will be displayed. The screen may not be magnified depending on your settings.

3 Adjust the focus by rotating the focus ring. 4 Touch [ENTER]. The icon of the item to which the focus position has been registered will be highlighted in yellow. To select a different item, perform the operations in Steps 2s4.

5 Touch [EXIT] to complete the setting. The focus positions of the items you have set will be registered.

This function is not available in the following cases: j When Auto Focus is used j During Freeze Frame (l 81) j In Variable Frame Rate Mode (l 91)

The focus position settings are canceled in the following cases: j If you turn the unit off j If you press the THUMBNAIL button j If you operate the zoom

Registering a focus position

: [RECORD SETUP] # [FOCUS TRANSITION] # [SET]

[1]/[2]/[3]

MENU

- 52 -

Select the [FOCUS TRANSITION] menu. (l 52) Register [FOCUS TRANS] to a USER button. (l 74)

1 Switch to Manual Focus Mode. (l 44) 2 Press the USER button to which [FOCUS TRANSITION] is registered or touch

the applicable USER button icon. 3 Touch a registered item ([1]s[3]). Focus Transition will start. Focus will shift slowly from the

current position to the registered position. This will take a few seconds. (l 54)

As the focus shifts, the Focus Transition bar will move from [S] to [E].

4 Touch [EXIT] to exit Focus Transition.

If you move this unit a lot after setting the focus position, focus may not stop at the set position. When Focus Transition is in use, focus cannot be adjusted with the focus ring. Focus Transition is not available in the following cases:

j When Auto Focus is used j During Freeze Frame (l 81) j In Variable Frame Rate Mode (l 91) j When color bars are displayed. (l 95) j When a remote control (commercially-available) is connected (l 113)

Focus Transition settings are canceled in the following cases. To use Focus Transition again, register a focus position again. (l 52) j If you operate the zoom j If you enable or disable Infrared Recording Mode

You can only use the following USER button functions by pressing one of the USER buttons 5s8 when Focus Transition is in use (l 74):

j [FOCUS ASSIST] j [FOCUS TRANSITION] j [INFRARED REC] j [BACKGROUND]

j [PRE-REC] j [EVF ON/OFF] j [AUTO REC] j [MENU]

Using Focus Transition

S E

1 2 3

MF50

A [EXIT] B Focus Transition bar

- 53 -

You can switch between the items or exit Focus Transition by pressing the USER buttons 1s4.

When using Focus Transition, functions registered to the USER buttons 1s4 do not work with the USER buttons.

To set the Focus Transition time 1 Select the menu.

2 Touch the desired setting item.

When [DIRECT] is set, a focus position changes as soon as Focus Transition starts. 3 (If you have selected [2-15 SEC.] in Step 2)

Touch / to set the duration. You can set a Focus Transition time of 2s15 seconds (by 0.5 second increments). Touch [RETURN]. 4 Touch [EXIT] to complete the setting.

To start Focus Transition and recording simultaneously You can start Focus Transition and recording simultaneously by enabling [FOCUS TRANSITION REC]. 1 Select the menu.

2 Touch the item.

3 Touch [EXIT] to complete the setting. 4 When the recording screen is displayed, press the USER button to which

[FOCUS TRANSITION] is registered or touch the applicable USER button icon.

5 Press the recording start/stop button or the USER button to which [AUTO REC] is registered.

Recording and Focus Transition will start simultaneously. Focus will shift to the position you have set in Step 2.

USER button Corresponding setting USER1 to USER3 [1] to [3]

USER4 [EXIT]

: [RECORD SETUP] # [FOCUS TRANSITION TIME]

[DIRECT]/[2-15 SEC.]/[20 SEC.]/[30 SEC.]/[45 SEC.]/[60 SEC.]/[90 SEC.]

: [RECORD SETUP] # [FOCUS TRANSITION REC]

[1]/[2]/[3]

MENU

MENU

- 54 -

To set the length of time before Focus Transition starts

Select the menu.

Automatic White Balance function may not reproduce natural colors depending on the scenes or lighting conditions. If so, you can adjust the White Balance manually.

Switch to Manual Mode. (l 36)

1 Set the WHITE BAL switch to PRST. The White Balance mode set in [WB PRESET] will be displayed. If it will switch to A or B, the White Balance mode is set to [Ach] or [Bch].

2 Press the AWB button to switch the White Balance mode. The mode will be switched each time the AWB button is pressed:

[P3200K] # [P5600K] # [VAR ]

If you set the White Balance mode to [ATW] in either of the following ways, even if you press the AWB button, the White Balance mode cannot be switched: j Pressing the USER button to which [ATW] is registered (l 74, 78) j Setting the WHITE BAL switch to the position corresponding to your [ATW SET] setting

(l 152)

: [RECORD SETUP] # [FOCUS TRANSITION WAIT] # desired time

[0 SEC.]/[5 SEC.]/[10 SEC.]

Recording

White Balance

MENU

P3200K

A [WB] B White Balance

1 AWB button 2 Jog dial 3 WHITE BAL switch

- 55 -

About White Balance modes

*1 This setting is selected automatically when one of the following operations is performed: j Set [ATW] to [ON] and switch to Auto Mode. (l 36) j Press the USER button to which [ATW] is registered. (l 74, 78) j Set the WHITE BAL switch to the position corresponding to your [ATW SET] (l 152) setting.

*2 You can set this mode with a USER button.

In the following cases, even if you press the USER button to which [ATW] is registered or change the position of the WHITE BAL switch, the White Balance mode cannot be changed: j In Auto Mode with [ATW] set to [ON] j During Freeze Frame (l 81)

[RB GAIN CONTROL SETTING] allows you to fine-adjust the color balance for each position of the WHITE BAL switch. (l 134)

Mode Settings

ATW (ATW)*1 It will automatically adjust in accordance with the recording condition.

LOCK (ATW Lock)*2

It will lock the setting for ATW. (l 57)

P3200K (P3200K)

Preset value for studio/indoor recording (halogen lamp, etc.)

P5600K (P5600K)

Preset value for outdoors

VAR (VAR) Setting can be finely adjusted in accordance to the recording conditions. (l 58)

Ach (Ach) Setting can be optimized for the scene to be recorded when you set the WHITE BAL switch to [A]. (l 58)

Bch (Bch) Setting can be optimized for the scene to be recorded when you set the WHITE BAL switch to [B]. (l 58)

- 56 -

You can customize the ATW settings for various recording conditions by adjusting the settings of [ATW SPEED], [ATW TARGET R], and [ATW TARGET B] individually.

Adjusting the control speed of ATW Select the menu.

Fine-adjusting the color balance of ATW 1 Select the menu.

[ATW TARGET R] adjusts the intensity of red. [ATW TARGET B] adjusts the intensity of blue. 2 Touch / to adjust settings. You can select a value between s10 and r10. 3 Touch [EXIT] to complete the setting.

You can set ATW Lock by registering [ATW LOCK] to a USER button. Please refer to page 74 for details about setting the USER button. 1 Set the White Balance mode to [ATW]. 2 Press the USER button to which [ATW LOCK] is registered or touch the

applicable USER button icon. To cancel ATW Lock, press the USER button or touch the USER button icon again. Canceling

ATW Lock will return the White Balance mode back to [ATW].

This function is not available in the following cases: j When the White Balance mode is set to something other than [ATW]

It will be canceled when the unit is turned off.

Customizing ATW for various recording conditions

: [SW SETUP] # [ATW SPEED] # desired setting

[FAST]/[NORMAL]/[SLOW]

: [SW SETUP] # [ATW TARGET R] or [ATW TARGET B]

To set ATW Lock

MENU

MENU

- 57 -

Setting the White Balance mode to [VAR] allows you to set a White Balance value between P2000K and P15000K. Use the jog dial to change the settings. Switch to Manual Mode. (l 36)

1 Set the White Balance mode to [VAR]. (l 55) 2 Rotate the jog dial to adjust the color balance.

3 Push the jog dial to finish the adjustment.

You can also access this setting by selecting menu items. [SW SETUP] # [WB VAR] (l 153)

1 Fill the screen with a white subject or place a white piece of paper in front of the lens.

2 Set the WHITE BAL switch to A or B. The White Balance mode will be set to [Ach] or [Bch]. 3 Press and hold the AWB button to set Auto White Balance. Adjust the Black Balance first, and then the White Balance. The screen goes dark momentarily,

WB SET OK is displayed, and the adjustment ends. If you have pressed the AWB button, only the White Balance can be adjusted. When

WB SET OK is displayed, the adjustment is complete.

When the mode of White Balance is set to something other than [Ach] or [Bch], the Auto Black Balance is performed by pressing and holding the AWB button. Setting is completed when the screen goes black momentarily and BB SET OK is displayed.

When the Auto White Balance/Auto Black Balance cannot be performed, an error message WB SET NG or BB SET NG is displayed on the screen. In such case, use other mode.

The contents previously set are maintained in the [Ach] or [Bch]. Perform the setting again when the recording condition has changed.

To finely adjust the White Balance

To set the White Balance in accordance to the recording scene

- 58 -

When recording a scene that is too dark (or bright) or a scene in a similar situation, manually adjust the iris and gain.

Iris adjustment

Switch to Manual Mode. (l 36)

1 Press the IRIS button to switch to Manual Iris Mode. disappears.

2 Adjust the iris by rotating the iris ring.

Iris value: CLOSE !# (F16 to F3.0) !# OPEN Value closer to CLOSE darken the image. Value closer to OPEN brighten the image. To return to Auto Iris Mode, press the IRIS button, or set [A.IRIS] to [ON] and switch to Auto

Mode. (l 36)

This item cannot be set during Freeze Frame. (l 81) Depending on the zoom magnification, there are iris values that are not displayed. In Auto Gain Mode or Auto Shutter Mode, the screen brightness may not change even if you

adjust the iris. (l 61, 63)

Recording

Iris/Gain adjustment

IRIS

F4.0

A Iris value B Auto iris icon*

* It is displayed in Auto Iris Mode. 1 IRIS button 2 Iris ring

- 59 -

You can customize Auto Iris motion settings for various recording conditions by adjusting the settings of [A.IRIS SPEED], [AUTO IRIS LEVEL], and [AUTO IRIS LEVEL EFFECT] individually.

Adjusting the control speed of Auto Iris Mode Select the menu.

Adjusting brightness during the Auto Iris Mode 1 Select the [AUTO IRIS LEVEL EFFECT] menu.

2 Touch / to adjust settings. You can select a value between s50 and r50. Touch [EXIT]. 3 Select the [AUTO IRIS LEVEL] menu.

If you select [OFF], the [AUTO IRIS LEVEL EFFECT] setting will not be applied. 4 Touch [EXIT] to complete the setting.

You can also change the [AUTO IRIS LEVEL] setting with a USER button. (l 88)

Utilizing the USER button It is convenient to use following functions of the USER button when it is set to Iris adjustment. Please refer to page 74 for details about setting the USER button.

Customizing Auto Iris motion settings for various recording conditions

: [SW SETUP] # [A.IRIS SPEED] # desired setting

[FAST]/[NORMAL]/[SLOW]

: [SCENE FILE] # [AUTO IRIS LEVEL EFFECT]

: [SCENE FILE] # [AUTO IRIS LEVEL] # [ON]

USER button function Effect

Backlight Compensation (l 77) Switches to automatic iris control to compensate the backlight. This will brighten the image on the screen to prevent getting dark when a backlight is hitting the subject from the back.

Spotlight (l 77) Switches to automatic iris control for spotlight. This will allow to clearly record an extremely bright subject.

MENU

MENU

MENU

- 60 -

Gain adjustment Use the jog dial to change the settings.

Switch to Manual Mode. (l 36)

1 Slide the GAIN switch.

2 Adjust the gain by rotating the jog dial. Gain value: (When [GAIN/ISO DISPLAY CHG] (l 173) is set to [GAIN]) 0dB to 24dB Value closer to 0dB darken the image. Value closer to 24dB brighten the image.

(When [GAIN/ISO DISPLAY CHG] is set to [ISO]) ISO500 to ISO8000 Value closer to ISO500 darken the image. Value closer to ISO8000 brighten the image.

Auto Gain Mode is activated when one of the following operations is performed: j Setting [AGC] to [ON] and switching to Auto Mode (l 36) j Setting any of [LOW GAIN], [MID GAIN] and [HIGH GAIN] to [AUTO] and setting the GAIN

switch to the corresponding position.

A Gain value The gain value changes depending on [GAIN/ISO DISPLAY CHG] setting:

j (When set to [GAIN]) In Auto Gain Mode, AGC is displayed; in Manual Gain Mode, the gain value is displayed in dB.

j (When set to [ISO]) In Auto Gain Mode, ISO AUTO is displayed; in Manual Gain Mode, the gain value is displayed in ISO.

B [GAIN]

L: Sets the gain value to a value set in [LOW GAIN] (l 150).

M: Sets the gain value to a value set in [MID GAIN] (l 150).

H: Sets the gain value to a value set in [HIGH GAIN] (l 151).

0dB

1 Jog dial 2 GAIN switch

- 61 -

It is not possible to adjust the gain value using the GAIN switch and jog dial in the following situations: j During Freeze Frame (l 81)

If the gain value is increased, the noise on the screen increases. In Auto Iris Mode or Auto Shutter Mode, the screen brightness may not change even if you adjust

the gain. (l 59, 63)

Changing the maximum possible gain value for Auto Gain Mode Select the menu.

(When [GAIN/ISO DISPLAY CHG] is set to [GAIN])

(When [GAIN/ISO DISPLAY CHG] is set to [ISO])

You can use Super Gain by registering [SUPER GAIN] to a USER button. Super Gain allows you to set a Super Gain value.

Please refer to page 74 for details about setting the USER button.

Switch to Manual Mode. (l 36) Press the USER button to which [SUPER GAIN] is registered or touch the applicable USER button icon. To cancel Super gain, press the USER button or touch the USER button icon again.

To change the gain value of Super Gain Select the menu.

(When [GAIN/ISO DISPLAY CHG] is set to [GAIN])

(When [GAIN/ISO DISPLAY CHG] is set to [ISO])

Super Gain is not available in the following cases: j In Auto Gain Mode j During Freeze Frame (l 81) j In High-sensitivity Recording Mode (l 148)

: [AUTO SW] # [AGC LIMIT] # desired setting

[3 dB]/[6 dB]/[9 dB]/[12 dB]/[15 dB]/[18 dB]/[21 dB]/[24 dB]

[ISO1000]/[ISO2000]/[ISO4000]/[ISO8000]

Super Gain

[GAIN/ISO DISPLAY CHG] (l 173) setting Gain value in Super Gain [GAIN] [30 dB] or [36 dB]

[ISO] [ISO16000] or [ISO32000]

: [SW SETUP] # [SUPER GAIN] # desired setting

[30 dB]/[36 dB]

[ISO16000]/[ISO32000]

MENU

MENU

- 62 -

Adjust the shutter speed when recording fast-moving subjects. Use the jog dial to change the settings.

Switch to Manual Mode. (l 36)

1 Press the SHUTTER button to switch to Manual Shutter Mode.

2 Adjust the shutter speed by rotating the jog dial. To return to Auto Shutter Mode, press the SHUTTER button, or set

[AUTO SHUTTER] to [ON] and switch to Auto Mode. (l 36)

Shutter speed: (When [SHUTTER DISPLAY CHG] is set to [sec]) The shutter speed varies depending on the frame rate in [REC FORMAT] or [OUTPUT FORMAT]. (l 142, 147)

* Synchro Scan values (l 65) The shutter speed closer to 1/8000 is faster.

Recording

Manual shutter speed

Frame rates Shutter speed

59.94p/59.94i 1/60.0*!#1/2!#1/4!#1/8!#1/15!#1/30!#1/60!#...1/8000

29.97p 1/60.0*!#1/2!#1/4!#1/8!#1/15!#1/30!#1/50!#...1/8000

50.00p/50.00i/25.00p 1/50.0*!#1/2!#1/3!#1/6!#1/12!#1/25!#1/50!#...1/8000

23.98p/24.00p 1/48.0*!#1/2!#1/3!#1/6!#1/12!#1/24!#1/48!#...1/8000

SHUTTER

1/60

A Shutter speed This is displayed in Manual Shutter Mode. [SHUTTER DISPLAY CHG] allows you to switch

the shutter speed display between seconds and angle. (l 172)

B [SHUTTER]

1 SHUTTER button 2 Jog dial

- 63 -

(When [SHUTTER DISPLAY CHG] is set to [deg]) 5.0d to 360.0d It is possible to adjust the shutter speed in increments of 0.5d. The shutter speed closer to 5.0d is faster. You can adjust the setting faster by rotating the jog dial while pushing and holding it.

Shutter speed guide for fast moving subjects Refer to the table below to reduce afterimages that appear when playback is paused.

To set an upper limit on the shutter speed in Auto Shutter Mode Select the menu.

*1 This option is not displayed when [SYSTEM FREQ] is set to [50.00Hz]. *2 This option is not displayed when [SYSTEM FREQ] is set to [59.94Hz].

The shutter speed cannot be adjusted in the following cases: j During Freeze Frame (l 81)

You may see a band of light around an object that is shining very bright, or highly reflective. During normal playback, image movement may not look smooth. If you record an extremely bright object or record under indoor lighting, color and screen

brightness may change or a horizontal line may appear on the screen. In such cases, change settings as follows: j Set this unit to Auto Shutter Mode. j Adjust the shutter speed to 1/50, 1/60 or 1/100. j Adjust the Synchro Scan setting

In Auto Iris Mode or Auto Gain Mode, the screen brightness may not change even if you adjust the shutter speed. (l 59, 61)

[AUTO SHUTTER LIMIT] does not work when [SHUTTER DISPLAY CHG] is set to [deg].

Subject Shutter speed

Golf or tennis shot 1/500 to 1/2000

Roller coaster 1/500 to 1/1000

: [AUTO SW] # [AUTO SHUTTER LIMIT] # desired setting

[1/100]/[1/120]*1/[1/125]*2/[1/250]/[OFF]

MENU

- 64 -

If you press the jog dial when the shutter speed is displayed as a decimal number, the Synchro Scan setting will be displayed. You can fine-adjust the shutter speed by adjusting the Synchro Scan setting. This will minimize flickering and horizontal bars in images. Set [SHUTTER DISPLAY CHG] to [sec]. (l 172)

1 Press the SHUTTER button

2 When the shutter is displayed as a decimal number (e.g., 1/60.0), press the jog dial.

The display on the screen will switch from [ SHUTTER] to [ SYNCHRO], and the Synchro Scan setting will be displayed.

3 Adjust the Synchro Scan setting by rotating the jog dial. You can adjust the setting faster by rotating the jog dial while pushing and holding it. To minimize flickering and horizontal bands, look at the screen while adjusting the shutter speed.

4 Push the jog dial to set. The set shutter speed will also be applied to the [SYNCHRO SCAN] menu setting. (l 132)

Shutter speed range for the Synchro Scan setting The shutter speed range varies depending on the size and frame rate in [REC FORMAT] or [OUTPUT FORMAT]. (l 142, 147)

Making adjustments with Synchro Scan

Frame rates Shutter speed

59.94p/59.94i

(When the size for [REC FORMAT] or [OUTPUT FORMAT] is UHD (3840k2160))

1/60.0 to 1/249.7

(When the picture size for [REC FORMAT] or [OUTPUT FORMAT] is 1920k1080 or below)

1/60.0 to 1/249.8

29.97p 1/30.0 to 1/249.8

23.98p 1/24.0 to 1/249.6

24.00p

50.00p/50.00i 1/50.0 to 1/250.0

25.00p 1/25.0 to1/250.0

- 65 -

This unit can record audio in 2 ch. It is possible to switch between built-in microphone, external microphone, or connected audio equipment for each channel.

About audio recording methods The audio recording method varies depending on the [REC MODE] setting. (l 141)

Switching Audio Input

Using the built-in microphone Audio is recorded with the built-in microphone (2 ch) when the CH1 SELECT switch is set to INT(L) and the CH2 SELECT switch is set to INT(R).

Recording

Audio Input

Recording mode Audio recording method

MOV Linear PCM (LPCM)

MP4

AVCHD Dolby Digital

INT(L) INPUT1 INPUT2

CH1 SELECT

INT(R) INPUT1 INPUT2

CH2 SELECT

AUTO

MANU

CH 1

AUTO

MANU

CH 2

LINE

INPUT2

MIC 48V

LINE

INPUT1

MIC 48V

A CH1 SELECT switch B CH2 SELECT switch C CH1 switch D CH2 switch E INPUT1 switch F INPUT2 switch

- 66 -

Using an external microphone or audio equipment 1 Connect an external microphone or audio

equipment to AUDIO INPUT1, 2 terminals (XLR 3 pin). (l 14)

2 Use INPUT1 or INPUT2 switches to switch the connected audio input signal.

LINE*1: Audio equipment is connected MIC*2: An external microphone is connected +48V*2: When using a phantom microphone (which requires a power supply of +48 V) *1 The input level varies depending on the [INPUT1 LINE

LEVEL] or [INPUT2 LINE LEVEL] setting. (l 167) *2 The input level varies depending on the

[INPUT1 MIC LEVEL] or [INPUT2 MIC LEVEL] setting. (l 167)

3 Use the CH1 SELECT switch to select the input signal to be recorded to audio channel 1.

INT(L): Audio from the built-in microphone L (left) ch is recorded to audio channel 1. INPUT1: Audio from a device connected to AUDIO INPUT1 terminal (XLR 3 pin) is recorded to channel 1. INPUT2: Audio from a device connected to AUDIO INPUT2 terminal (XLR 3 pin) is recorded to channel 1.

4 Use the CH2 SELECT switch to select the input signal to be recorded to audio channel 2.

INT(R): Audio from the built-in microphone R (right) ch is recorded to audio channel 2. INPUT1: Audio from a device connected to AUDIO INPUT1 terminal (XLR 3 pin) is recorded to channel 2. INPUT2: Audio from a device connected to AUDIO INPUT2 terminal (XLR 3 pin) is recorded to channel 2.

Table of audio input patterns

Switch setting Channel or terminal used for signal input

CH1 SELECT switch

CH2 SELECT switch Audio channel 1 Audio channel 2

INT(L)

INT(R) Internal microphone Lch Internal microphone Rch

INPUT1 Internal microphone Lch AUDIO INPUT1 terminal

INPUT2 Internal microphone Lch AUDIO INPUT2 terminal

INPUT1

INT(R) AUDIO INPUT1 terminal Internal microphone Rch

INPUT1 AUDIO INPUT1 terminal AUDIO INPUT1 terminal

INPUT2 AUDIO INPUT1 terminal AUDIO INPUT2 terminal

INPUT2

INT(R) AUDIO INPUT2 terminal Internal microphone Rch

INPUT1 AUDIO INPUT2 terminal AUDIO INPUT1 terminal

INPUT2 AUDIO INPUT2 terminal AUDIO INPUT2 terminal

A AUDIO INPUT1 terminal (XLR 3 pin)

B AUDIO INPUT2 terminal (XLR 3 pin)

- 67 -

To remove the external microphone, etc., from the AUDIO INPUT1, 2 terminals (XLR 3 pin)

Set INPUT1, 2 switches to LINE or MIC if you connect equipment not compatible with +48 V. You can damage this unit or such equipment if you leave the setting at +48V.

This unit is turned off when a problem occurs with the +48 V power supply. The battery will discharge faster if you use a phantom microphone.

Adjusting the audio input level

You can set how to adjust the audio input level for each audio channel. Use the CH1 switch for channel 1 and the CH2 switch for channel 2.

1 Set the position of the CH1 or CH2 switch.

2 (If you have set to MANU) Adjust the input level operating the AUDIO LEVEL CH1/AUDIO LEVEL CH2 knobs.

Adjust confirming the audio level meter.

Remove while pushing on the PUSH section of the AUDIO INPUT1, 2 terminals (XLR 3 pin). Set the input signal to built-in microphone by switching

the CH1 SELECT, CH2 SELECT switches to INT (L) or INT (R) after removing the external microphone. Audio will not be recorded when motion picture is recorded without switching.

Selecting an adjustment method

AUTO: Adjusts the level automatically.

MANU: Adjusts the level manually.

A PUSH section

CH1

AUDIO LEVEL

CH2

A AUDIO LEVEL CH1/AUDIO LEVEL CH2 knobs B Audio level meter C -12 dB D 0 dB

- 68 -

ALC can reduce audio noise. For audio channel 1, select [AUDIO ALC CH1]: for audio channel 2, select [AUDIO ALC CH2].

Select the menu.

To set the ALC function to both audio channels 1 and 2 If you set [AUDIO ALC LINK] to [ON], when ALC works for either of the audio channels, it will also work for the other audio channel. 1 Set CH1 switch or CH2 switch to MANU. 2 Set [AUDIO ALC CH1]/[AUDIO ALC CH2] to ON. 3 Select the menu.

Using the ALC function

: [AUDIO SETUP] # [AUDIO ALC CH1] or [AUDIO ALC CH2] # desired setting

[ON]: Enables ALC, allowing you to record audio with reduced noise.

[OFF]: Allows you to record natural-sounding audio.

: [AUDIO SETUP] # [AUDIO ALC LINK] # [ON]

MENU

MENU

- 69 -

You can change a counter display that indicates how much time has elapsed during recording or playback.

Press the COUNTER button to switch the counter display. The display will be switched in the following order: Time Code # User Information* # Recording

Counter # Off.

* This is displayed only when [REC MODE] is set to [AVCHD]. (l 141)

Setting the Time Code Time code will display the recording time in hours, minutes, seconds, and frames. TC 00:00:00:00 (hour : minute : second : frame [NDF]) TC 00:00:00.00 (hour : minute : second . frame [DF]) The number of frames (frame count per second) varies depending on the frame rate in

[REC FORMAT] or [OUTPUT FORMAT]. (l 142, 147)

Recording

Counter display

Counter display Indications

Time Code TC 00:00:00:00 or TC 00:00:00.00 Display will change depending on the setting of the

[DF MODE]. (l 71)

User Information* (l 72) UB 00 00 00 00

Recording Counter (l 73) (In Recording Mode) 0:00:00 or SCN 0:00:00 (In Playback Mode) SCN 0:00:00 In Recording Mode, display will change depending on the

setting of the [REC COUNTER]. In Playback Mode, display will return to SCN 0:00:00 for

each scene.

Frame rates Frame 59.94p/59.94i/29.97p 0 to 29

50.00p/50.00i/25.00p 0 to 24

23.98p/24.00p 0 to 23

COUNTER

RESET/TC SET

A COUNTER button B RESET/TC SET button

- 70 -

Select the compensation mode for the time code. Set [SYSTEM FREQ] to [59.94Hz]. (l 141) Select the menu.

This item will be set to [NDF] automatically in following cases: j When the frame rate in [REC FORMAT] or [OUTPUT FORMAT] is 23.98p or 24.00p (l 142,

147) j During the Interval Recording (l 162)

This item will be automatically set to [NDF] and will not be displayed as a menu item when [SYSTEM FREQ] is set to [50.00Hz]. (l 141)

Sets the way the time code will move. Select the menu.

*1 If the frame rate in [REC FORMAT] or [OUTPUT FORMAT] is set to 23.98p, a slight time error may occur when switching to Playback Mode. (l 142, 147)

It is automatically set to [FREE RUN] in following cases: j When PRE-REC is enabled (l 86, 163) j When [2 SLOTS FUNC.] is set to [BACKGROUND] (l 159)

It is automatically set to [REC RUN] in following cases: j In Variable Frame Rate Mode*2 (l 91) j During the Interval Recording (l 162)

*2 [FREE RUN] is also available if the number of frames for the frame rate in [REC FORMAT] and the number of frames for Variable Frame Rate Mode are the same. Example: When [REC FORMAT] is set to [FHD 1080/59.94p 50M] and the frame rate is set to [60]

The time code will reset when the built-in lithium battery is exhausted when it is set to [FREE RUN].

[DF MODE]

: [RECORD SETUP] # [DF MODE] # desired setting

[DF]: Time code is compensated in accordance with the actual time. It is mainly used for broadcasting such as TV programs.

[NDF]: It will not compensate the time code. (There will be a difference from the actual time)

[TCG]

: [RECORD SETUP] # [TCG] # desired setting

[FREE RUN]*1: It will constantly move.

[REC RUN]: It will move only when recording.

MENU

MENU

- 71 -

You can set the initial time code.

1 Select the menu.

2 Touch the item to set and change with / . It will be set to 00h00m00s00f when the RESET/TC SET button is pressed. h is an abbreviation for hour, m for minute, s for second and f for frame.

3 Touch [EXIT] to complete the setting.

This unit will adjust the time code in accordance with the frame rate of the [REC FORMAT] (l 142) or [OUTPUT FORMAT] (l 147). Therefore, it may not be continuous from the previous final time code when the recording format is changed.

If the frame rate in [REC FORMAT] or [OUTPUT FORMAT] is set to 23.98p, set the number of frames to [00] or a multiple of 4. If you enter a different value, time code will not be recorded correctly.

Setting the User Information Eight digit hexadecimal alphanumeric can be entered and displayed as a memo information such as dates, control numbers, etc., into the User Information. UB 00 00 00 00 This is displayed only when [REC MODE] is set to [AVCHD]. (l 141)

You can set the User Information. Set [REC MODE] to [AVCHD]. (l 141)

1 Select the menu.

2 Touch the item to set and change with / . You can use numbers from 0 to 9 and letters from A to F. It will be set to 00 00 00 00 when the RESET/TC SET button is pressed.

3 Touch [EXIT] to complete the setting.

[TC PRESET]

: [RECORD SETUP] # [TC PRESET]

[UB PRESET]

: [RECORD SETUP] # [UB PRESET]

MENU

MENU

- 72 -

Setting the Recording Counter Recording Counter will display the recording time in seconds. 0:00:00 (hour : minute : second (When [REC COUNTER] is set to [TOTAL])) SCN 0:00:00 (hour : minute : second (When [REC COUNTER] is set to [SCENE]))

Select the counting method during the recording. Select the menu.

To reset the Recording Counter for the Recording Mode The Recording Counter will be set to 0:00:00 when the RESET/TC SET button is pressed while displaying the counter.

Synchronizing the time code with an external device

You can synchronize the default time code during multi-camera recording. In the following section, the device with the reference time code is referred to as master, while

the device to be synchronized is referred to as slave.

3 (On the master device) Select the [EXT TC LINK] menu.

The time code will be output from the TC PRESET IN/OUT terminal. To cancel the output of the time code, touch [EXIT].

4 (On the slave device) Select the [EXT TC LINK] menu.

[REC COUNTER]

: [DISP SETUP] # [REC COUNTER] # desired setting

[TOTAL]: The count continues to increase until the Recording Counter is reset.

[SCENE]: Resets the Recording Counter at start of recording. Counts the time of each recording session.

1 Connect the TC PRESET IN/OUT terminals of the two devices with a BNC cable (commercially-available), and turn them on.

Apply the same [REC FORMAT], [OUTPUT FORMAT] and [DF MODE] settings to the two devices. (l 71, 142, 147)

2 (On the master device) Select the [TCG] menu.

: [RECORD SETUP] # [TCG] # [FREE RUN]

: [RECORD SETUP] # [EXT TC LINK] # [MASTER]

MENU

TC PRESET IN/OUT

A TC PRESET IN/OUT terminal

MENU

MENU

- 73 -

[TCG] will be set to [FREE RUN].

5 (On the slave device) Press the RESET/TC SET button.

[TC LINK OK] will be displayed and the time code will be synchronized with that of the master device.

When the time code is not synchronized correctly, [TC LINK NG] is displayed. To cancel the operation without synchronizing the time code, touch [EXIT].

Use a commercially-available, double-shielded BNC cable equivalent to 5C-FB. [EXT TC LINK] cannot be set to [SLAVE] in the following cases:

j In Variable Frame Rate Mode (l 91) j During the Interval Recording (l 162)

Each of the USER button can register one function from the 38 available functions. There are eight USER buttons (USER1 to USER8) on the main body and four USER button icons

(USER9 to USER12) displayed on the LCD monitor.

Setting the USER button 1 Select the menu.

It is not possible to register functions to [USER9] to [USER12] in Playback Mode.

2 Touch the item to register. For the functions of the USER button that can be registered, refer to page 76. Touch [INHIBIT] if not registering. Next (Previous) page can be displayed by touching / .

3 Touch [EXIT] to complete the setting.

The tables below show the default settings.

Performing [ALL] in [INITIAL SET] restores these default settings. (l 178)

: [RECORD SETUP] # [EXT TC LINK] # [SLAVE]

Recording

USER button

: [USER SW] # [USER1] to [USER12]

USER1 button [DRS] USER7 button [WFM]

USER2 button [ATW] USER8 button [REC CHECK]

USER3 button [BACKLIGHT] USER9 button [FRZ FRAME]

USER4 button [FOCUS MACRO] USER10 button [EVF/LCD DETAIL]

USER5 button [O.I.S.] USER11 button [ATW LOCK]

USER6 button [ZEBRA] USER12 button [MENU]

MENU

MENU

- 74 -

Using the USER button To use the set USER button, press USER1 to USER8 button or touch the USER9 to USER12 button icon displayed when you touch the LCD monitor.

To cancel, press the USER button or touch the USER button icon again. For canceling or using of the following functions for the USER buttons, refer to each page.

j Black Fade (l 78) j White Fade (l 78) j Digital Zoom (l 79) j Recording Check (l 80) j Last Scene Delete (l 80) j Area Mode (l 82) j Focus Transition (l 52)

j Background (l 85) j WFM (l 87) j Zebra (l 88) j Scene File (l 89) j Auto Recording (l 90) j AF Area Range Adjustment (l 90) j Log View Assist (l 94) j LCD/EVF Output (l 24)

Switch display/not-display of the USER buttons Display/not-display of the USER button icons in the LCD monitor can be switched. Select the menu.

Check the setting of the USER buttons

(When you use the USER1 to USER7 button) (When you use the USER8 button)

(When you use the USER9 to USER12 button)

USER

1

2

3

4 5

O.I.S. 6

ZEBRA 7

WFM

8

REC CHECK

SCN1 SCN2 SCN3 SCN4 SCN5 SCN6

A [USER9] B [USER10] C [USER11] D [USER12]

: [USER SW] # [USER BUTTON DISPLAY] # [ON] or [OFF]

To check the USER button (USER1 to 8) settings on the recording screen, use the DISP/MODE CHK switch to display the mode information screen. (l 96)

MENU

- 75 -

Functions of the USER button List of USER button functions

*1 Not available in Auto Mode *2 Not available for Auto Focus

Item Icon Function [INHIBIT] [INH] Invalid

[FOCUS ASSIST] [FA] Focus Assist

[BACKLIGHT] [B.Light] Backlight Compensation

[SPOTLIGHT] [S.Light] Spotlight

[BLACK FADE] [B.FD] Black Fade

[WHITE FADE] [W.FD] White Fade

[ATW] [ATW] Auto Tracking White Balance

[ATW LOCK] [ATW.L] ATW Lock

[D.ZOOM] [D.ZM] Digital Zoom

[HISTOGRAM] [HIST] Histogram

[REC CHECK] [REC.C] Recording Check

[LAST SCN DEL] [LstDel] Last Scene Delete

[DRS] [DRS] DRS

[FRZ FRAME] [FRZ] Freeze Frame

[SUPER GAIN] [S.Gain] Super Gain*1

[AREA] [AREA] Area Mode

[FOCUS TRANS] [F.Tran] Focus Transition*2

[CAPTURE] [Capture] Capture

[EVF/LCD DETAIL] [DETAIL] EVF/LCD detail

[IR REC] [IR REC] Infrared Recording

[LEVEL GAUGE] [Level] Level Gauge

[BACKGROUND] [Backgr] Background

[FLASH BAND] [FBC] Flash band compensation

[PRE-REC] [PRE-REC] PRE-REC

[WFM] [WFM] WFM

[FAST ZOOM] [F.ZOOM] Fast Zoom

[EVF ON/OFF] [EVF SW] EVF ON/OFF

[A.IRIS LEVEL] [A.IRIS] Auto Iris Level

[ZEBRA] [ZEBRA] Zebra

[O.I.S.] [O.I.S.] Optical Image Stabilizer

[SCENE FILE] [SCN FILE] Scene File

[AUTO REC] [AutoRec] Auto Rec

- 76 -

The following USER button function can also be set from the menu. j [HISTOGRAM] (l 174) j [DRS] (l 139) j [INFRARED REC] (l 164) j [LEVEL GAUGE] (l 173) j [EVF/LCD DETAIL] (l 45) j [FLASH BAND COMPENSATION] (l 140) j [PRE-REC] (l 163) j [WFM] (l 155) j [FAST ZOOM] (l 41)

j [AUTO IRIS LEVEL] (l 60) j [ZEBRA] (l 155) j [O.I.S.] (l 151) j [SCENE FILE] (l 131) j [AF AREA WIDTH] (l 47) j [VFR MODE] (l 131) j [FOCUS MACRO] (l 154) j [i.Zoom] (l 41) j [LCD/EVF OUTPUT] (l 24)

Register Focus Assist to a USER button. (l 74) You can set the Focus Assist. (l 48)

Register Backlight Compensation to a USER button. (l 74) Switches to automatic iris control to compensate the backlight. This makes the image brighter to prevent darkening of a backlit subject. appears when it is set. It will return to standard Auto Iris Mode ( ) when it is canceled. (l 59)

This item cannot be set during Freeze Frame. (l 81)

Register Spotlight to a USER button. (l 74) Switches to automatic iris control for spotlight. Very bright object is recorded clearly. appears when it is set. It will return to standard Auto Iris Mode ( ) when it is canceled. (l 59)

This item cannot be set during Freeze Frame. (l 81)

Item Icon Function [AF AREA] [AF Area] AF area width adjustment

[VFR] [VFR] Variable Frame Rate Mode

[FOCUS MACRO] [F.Macro] Focus Macro

[i.ZOOM] [i.Zoom] i.Zoom

[LOG VIEW ASSIST] [LogView] Log View Assist

[LCD/EVF OUTPUT] [LCD/EVF] LCD/EVF Output

[MENU] [MENU] Menu

Focus Assist

Backlight Compensation

Spotlight

- 77 -

Register Black Fade to a USER button. (l 74) Fade in/fade out effect (black) can be added to the video and audio that is being recorded.

Press USER button or touch USER button icon in the recording screen. Fade out will start, and fade in will start after completing the fade out. It will fade out when the button is pressed and held, and fade in will start when the button is

released.

Recording will not start even if the fade out is started. It is possible to press the recording start/ stop button during the fade in or fade out.

Black Fade is not possible in following cases: j In Variable Frame Rate Mode (l 91) j During the Interval Recording (l 162)

The thumbnails of scenes recorded using fade in become black.

Register White Fade to a USER button. (l 74) Fade in/fade out effect (white) can be added to the video and audio that is being recorded.

Press USER button or touch USER button icon in the recording screen. Fade out will start, and fade in will start after completing the fade out. It will fade out when the button is pressed and held, and fade in will start when the button is

released.

Recording will not start even if the fade out is started. It is possible to press the recording start/ stop button during the fade in or fade out.

White Fade is not possible in following cases: j In Variable Frame Rate Mode (l 91) j During the Interval Recording (l 162)

The thumbnails of scenes recorded using fade in become white.

Register ATW to a USER button. (l 74) The White Balance can be changed to ATW. (l 55)

This function is not available when the White Balance mode is set to [ATW LOCK].

Register ATW Lock to a USER button. (l 74) This sets the White Balance mode to [ATW LOCK].(l 57)

Black Fade

White Fade

ATW

ATW Lock

- 78 -

Register Digital Zoom to a USER button. (l 74) Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) Press USER button or touch USER button icon in the recording screen. When [DIGITAL ZOOM] is set to [k2], [k5] or [k10], Digital Zoom will be turned on/off each time

you press the button. When [DIGITAL ZOOM] is set to [TOGGLE], the zoom magnification will change each time you

press the button. 2k # 5k # 10k # Setting canceled

To change the zoom magnification of Digital Zoom The zoom magnification of Digital Zoom varies depending on the [DIGITAL ZOOM] setting.

When using Digital Zoom, the larger you set the zoom magnification, the lower the picture quality becomes.

Digital Zoom is not possible in following cases: j When [OUTPUT BITS] is set to [4:2:2(10bit)] j During Freeze Frame (l 81) j When using Area Mode (l 82) j In Variable Frame Rate Mode (l 91) j During the Interval Recording (l 162)

Digital zoom is canceled in following cases: j If you turn the unit off j If you press the THUMBNAIL button j When [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

Register Histogram to a USER button. (l 74) A graph with brightness as horizontal axis and number of pixels at that brightness as vertical axis is displayed. It is possible to determine the exposure of the whole image by looking at the distribution in the graph.

To move a histogram You can move a histogram by touching and holding the histogram display A. Slide the display while touching it to move it to the desired display location.

Digital Zoom

: [SW SETUP] # [DIGITAL ZOOM] # desired setting

[k2]: Sets the zoom magnification to 2k.

[k5]: Sets the zoom magnification to 5k.

[k10]: Sets the zoom magnification to 10k.

[TOGGLE]: Changes the zoom magnification each time you press the applicable USER button.

Histogram

MENU

- 79 -

This function is not available in the following cases: jWhen [REC FORMAT] is set to [UHD 2160/59.94p 150M] or [UHD 2160/50.00p 150M] (l 142) jDuring Freeze Frame (l 81)

To adjust the brightness, refer to page 59.

Register Recording Check to a USER button. (l 74) Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) Approximately 2 seconds at the end of the video recorded last can be played back. It will return to recording screen once the playback is completed.

Playback operation is not possible during the Recording Check. Recording Check is not possible in following cases: jWhen the unit is turned on/off jWhen the THUMBNAIL button is pressed jWhen the SD card is inserted/removed jWhen [OUTPUT BITS] is set to [4:2:2(10bit)] jWhen the setting of [REC FORMAT] is changed (l 142) jSet [2 SLOTS FUNC.] to [SIMULTANEOUS] or [BACKGROUND]. (l 159) jPRE-REC is used (l 86, 163) jDuring the Interval Recording (l 162) jDuring Freeze Frame (l 81)

Register Last Scene Delete to a USER button. (l 74) Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) The motion picture recorded last can be deleted. Deleted scenes cannot be restored. 1 Press USER button or touch USER button icon in the recording screen. 2 Touch [YES]. It will return to recording screen without deleting by touching [NO].

Last Scene Delete is not possible in following cases: jWhen the unit is turned on/off jWhen the THUMBNAIL button is pressed jWhen the SD card is inserted/removed jWhen [OUTPUT BITS] is set to [4:2:2(10bit)] jWhen the setting of [REC FORMAT] is changed (l 142) jSet [2 SLOTS FUNC.] to [SIMULTANEOUS], [BACKGROUND] or [DUAL CODEC]. (l 159) jDuring the Interval Recording (l 162)

Recording Check

Last Scene Delete

- 80 -

Register DRS to a USER button. (l 74) Selects the DRS (Dynamic Range Stretcher) function. It is possible to expand the dynamic range by compressing the video signal level of the highly illuminated area that gets washed out with standard recording.

This item cannot be set in Variable Frame Rate Mode. (l 91) If there are extremely dark or bright parts or the brightness is insufficient, the effect may not be

clear. It is also possible to adjust the compression level of the highly illuminated area by changing the

[DRS EFFECT] setting. (l 139)

Register Freeze Frame to a USER button. (l 74) Freezes the image on the unit. will appear on the screen and flash.

If you record a motion picture during Freeze Frame, the frozen image and sounds will be recorded.

You can perform the following camera operations during Freeze Frame. Other camera operations will be disabled. j Recording motion pictures j Canceling Freeze Frame j Operating the FOCUS A/M/ switch j Operating the WHITE BAL switch j Operating the GAIN switch

This function is not available in the following cases: j When using Focus Assist (l 48) j In Variable Frame Rate Mode (l 91) j During the Interval Recording (l 162) j When color bars are displayed. (l 95)

Freeze Frame is canceled in the following cases: j Turning off the unit j When the THUMBNAIL button is pressed j Setting this unit to Variable Frame Rate Mode j When [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

Register Super Gain to a USER button. (l 74) Switch to Manual Mode. (l 36) This changes the gain value to a [SUPER GAIN] value. (l 62)

DRS

Freeze Frame

Super Gain

Freeze

- 81 -

You can apply a variety of effects to the subject you touch. Setting an Area Mode effect You can select the following menu items to set an effect to be applied when you touch the subject.

Using Area Mode Register Area Mode to a USER button. (l 74) 1 Press the applicable USER button or touch the applicable USER button icon

on the recording screen. Area Mode will be enabled and will be displayed.

2 Touch the recording screen. The area frame will be displayed on the part you have

touched. The effect of the selected menu item will be applied.

To turn off Area Mode (With a USER button) Press the USER button (With a USER button icon) 1 Touch and hold the recording screen to

display operation icons. 2 Touch the USER button icon.

To change the size of the area frame You can rotate the jog dial to change the size of the area frame. The area frame is available in three sizes.

Area Mode

: [SW SETUP] # [AREA MODE] # desired setting

[INH]: Does not apply any effects of Area Mode.

[FOCUS]: Optimizes the focus automatically for the subject you touch

[IRIS]: Optimizes the iris automatically for the subject you touch.

[Y GET]: Displays the luminance level of the subject you touch.

[FOCUS/IRIS]: Optimizes the focus and iris automatically for the subject you touch.

[FOCUS/Y GET]: Optimizes the focus automatically for the subject you touch and displays the luminance level of the subject.

MENU

A Area frame

- 82 -

Area Function is not possible in following cases: j In Variable Frame Rate Mode (l 91) j When a remote control (commercially-available) is connected (l 113)

Area mode is canceled in following cases: j If you turn the unit off j If you press the THUMBNAIL button j When you set [REC FORMAT] to [4K 2160/24.00p 100M] (l 142) j When you set [OUTPUT FORMAT] to [4K 2160/24.00p] (l 147) j When the setting of [ASPECT CONVERT] is changed (l 148) j When [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

When using Area Mode, even if you set [ZEBRA] to [MARKER], the luminance display frame will not be displayed. (l 88, 155) In addition, the luminance level will not be displayed if [AREA MODE] is set to [FOCUS], [IRIS] or [FOCUS/IRIS].

Register Focus Transition to a USER button. (l 74) Switch to Manual Focus Mode. (l 44) With Focus Transition, you can move the current focus position to a pre-registered focus position. (l 52)

Register Capture to a USER button. (l 74) You can record still pictures or create still pictures from recorded motion pictures. (l 34, 106)

Register EVF/LCD detail to a USER button. (l 74) [EVF/LCD DETAIL] helps you achieve focus easier by emphasizing the outlines of an image displayed on the LCD monitor or the viewfinder. (l 45) These settings will not affect the images actually recorded.

Focus Transition

Capture

EVF/LCD detail

- 83 -

Register Infrared Rec to a USER button. (l 74) This changes the Infrared Recording Mode setting.

This unit operates as follows in Infrared Recording Mode: j appears on the screen. j The iris, gain, and shutter speed are adjusted automatically. j When [AUTO SLOW SHTR] is set to [ON], the shutter speed will be automatically adjusted to

1/30, 1/24 or 1/25. (l 158)

It is recommended to use a tripod. It takes longer to focus with Auto Focus in dark locations. Do not use this function in a bright location. Doing so may cause malfunction. You can record a clear image by positioning the center area of the screen over the subject. [INFRARED REC] cannot be set in Variable Frame Rate Mode. (l 91) Focus values may not be displayed correctly in Infrared Recording Mode. (l 44) The following menu items are not available in Infrared Recording Mode:

j [SCENE FILE] (l 131) j [MASTER DETAIL] (l 132) j [DETAIL CORING] (l 133) j [SKIN TONE DTL] (l 133) j [V DETAIL LEVEL] (l 133) j [KNEE APE LEVEL] (l 134) j [RB GAIN CONTROL SETTING] (l 134) j [CHROMA LEVEL] (l 135) j [CHROMA PHASE] (l 135) j [MATRIX] (l 135) j [COLOR CORRECTION SETTING]

(l 136) j [MASTER PED] (l 137) j [GAMMA MODE] (l 137) j [BLACK GAMMA] (l 138) j [BLACK GAMMA RANGE] (l 138) j [KNEE MODE] (l 138) j [KNEE MASTER POINT] (l 138)

j [KNEE MASTER SLOPE] (l 139) j [DRS] (l 81, 139) j [DRS EFFECT] (l 139) j [AUTO IRIS LEVEL] (l 60, 88) j [AUTO IRIS LEVEL EFFECT] (l 60) j [V-Log L MODE] (l 140) j [ATW TARGET R] (l 57) j [ATW TARGET B] (l 57) j [WB VAR] (l 153) j [MF ASSIST] (l 51) j [CUSTOM AF] (l 46) j [AF SPEED] (l 46) j [AF SENSITIVITY] (l 46) j [FOCUS TRANSITION] (l 52)

The following functions are not available in Infrared Recording Mode: j Focus Transition (l 52) j Change the White Balance mode (l 55) j Iris adjustment (l 59) j Gain adjustment (l 61) j AGC Limit (l 62) j Shutter speed adjustment (l 63) j ND filter (l 96)

j Backlight Compensation (l 77) j Spotlight (l 77) j ATW (l 78) j ATW Lock (l 57) j Super Gain (l 62)

Infrared Rec

- 84 -

Register Level Gauge to a USER button. (l 74) This function displays the horizontal/vertical tilt of the unit with the electronic level. To correct the tilt

The horizontal tilt display A and vertical tilt display B appear yellow when there is a tilt, and appear green when there is almost no tilt.

The maximum tilt display angles are approximately 45 o in horizontal direction and 10 o in vertical direction.

The electronic level does not affect the actual recorded images.

This function is not available in the following cases: j During Freeze Frame (l 81) j When color bars are displayed. (l 95)

If [SELF SHOOT] (l 175) is set to [MIRROR], the electronic level will not be displayed when you record yourself.

Even when the tilt is in the corrected state, an error of approximately 1 o may occur. In the following cases, the electronic level may not be displayed correctly:

j When moving this unit j When pointing this unit up or down at an angle closer to perpendicular

Register Background to a USER button. (l 74) When [2 SLOTS FUNC.] is set to [BACKGROUND], you can start/stop background recording. When the recording destination of motion pictures is set to [SD CARD 1] in [MEDIA SELECT]

(l 32), [SD CARD 2] will be used for background recording. The following instructions assume that the recording destination of motion pictures is set to [SD CARD 1].

Set [2 SLOTS FUNC.] to [BACKGROUND]. (l 159) is displayed for SD CARD 2.

(To start background recording) Press the applicable USER button or the applicable USER button icon. Background recording will start on the SD card in SD CARD 2. ( will be displayed in red.)

(To stop background recording) While motion picture recording to [SD CARD 1] is stopped, press and hold the applicable USER button or the USER button icon.

Level Gauge

(Horizontal direction) (Vertical direction)

When correcting the leftward tilt When correcting the downward tilt

Background

BACKGR

BACKGR

- 85 -

Please refer to page 160 about Background recording.

Register Flash band compensation to a USER button. (l 74) If you set this item to [ON], you can compensate for and reduce flash band, a phenomenon that creates markedly different levels of luminance between the top and bottom of the image when recording is performed in an environment where another camera is firing its flash. FBC appears on the screen.

This function is not available in the following cases: j When the frame rate in [REC FORMAT] or [OUTPUT FORMAT] is 29.97p, 23.98p, 24.00p or

25.00p (l 142, 147) j When using [DIGITAL ZOOM] (l 79) j In Variable Frame Rate Mode (l 91)

The setting will be turned off in the following cases: j If you turn the unit off j If you press the THUMBNAIL button j When [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

[SHUTTER DISPLAY CHG] is fixed to [sec]. (l 172) Manual Shutter Mode will be activated. This will fix the shutter speed to 1/60 or 1/50.

Register PRE-REC to a USER button. (l 74) Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) This allows the recording of an image and audio to start before you press the recording start/stop button. AVCHD scenes will be recorded from approximately 3 seconds before the operation, while MOV/MP4 will be recorded from approximately 4 seconds before the operation. [P-] is displayed on the screen. After you start recording, the display changes to [P-REC].

Aim the unit at the subject beforehand. There is no beep sound. This function is not available in the following cases:

j When you set [OUTPUT BITS] to [4:2:2(10bit)] j In Variable Frame Rate Mode (l 91) j When [2 SLOTS FUNC.] is set to [BACKGROUND] (l 159) j During the Interval Recording (l 162)

In the following cases, a 3 second image that precedes the recording of an AVCHD scene or a 4 second scene that precedes the recording of an MOV/MP4 scene may not be recorded: j When 3 hours has just passed since you set PRE-REC j If the length of time from when [PRE-REC] is set to [ON] to when you start recording is too

short j If the length of time from when you display the recording screen by turning it off and on or

pressing the THUMBNAIL button to when you start recording is too short since you set PRE- REC

Images displayed on the thumbnail in Playback Mode will differ from the motion pictures displayed at the start of playback.

Flash band compensation

PRE-REC

- 86 -

Register WFM to a USER button. (l 74) This function displays waveforms on the LCD monitor.

Press USER button in the recording screen. When [WFM TYPE] is set to [WAVE] or [VECTOR], each press of the button enables/disables

WFM. When [WFM TYPE] is set to [WAVE/VECTOR], each press of the button switches the setting.

WAVE (wave display) # VECTOR (vector display) # OFF

If you have enabled WFM by touching the applicable USER button icon, set [WFM] to [OFF] to disable it.

This function is not available in the following cases:

j When using the viewfinder j When recording yourself (l 28) j When using Focus Assist (l 48)

j During Freeze Frame (l 81) j When color bars are displayed. (l 95)

[WFM] will be canceled in the following cases: j If you turn the unit off j If you press the THUMBNAIL button j When [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

To change the type of WFM Select the menu.

This function is not available in the following cases: j When using Focus Assist (l 48) j During Freeze Frame (l 81) j When color bars are displayed (l 95)

To change the display position of WFM Select the menu.

You can also change the waveform position to the upper left, upper right, bottom left or bottom right by performing one of the following operations while a waveform is displayed: j Rotating the jog dial j Sliding the waveform while touching it.

WFM

: [SW SETUP] # [WFM TYPE] # desired setting

[WAVE]: Displays waveforms as waves.

[VECTOR]: Displays waveforms as vectors.

[WAVE/VECTOR]: Switches the setting each time the applicable USER button is pressed.

: [SW SETUP] # [WFM POSITION] # desired setting

[TOP/LEFT]/[TOP/RIGHT]/[BOTTOM/LEFT]/[BOTTOM/RIGHT]

MENU

MENU

- 87 -

Register Fast Zoom to a USER button. (l 74) You can use Fast Zoom when operating the zoom with the zoom lever. (l 41)

Register EVF ON/OFF to a USER button. (l 74) This forces the viewfinder to turn on/off. After the viewfinder turns on, if the eye sensor detects your eye when it is moved closer to the eye

cup of the viewfinder the [EVF ON/OFF] setting will be canceled.

When the [LCD/EVF OUTPUT] is set to [LCD], this item cannot be set. (l 24)

Register Auto Iris Level to a USER button. (l 74) This enables/disables the Auto Iris Level. When this item is enabled, the [AUTO IRIS LEVEL EFFECT] setting is applied. (l 60)

Register Zebra to a USER button. (l 74) Press USER button or touch USER button icon in the recording screen. It will switch between the zebra display and the marker display every time the button is pressed. Zebra 1 # Zebra 2* # Marker* # setting canceled * It is not displayed when the [ZEBRA DETECT 2]/[MARKER] is set to [OFF]. (l 171)

Zebra display: Parts where white saturation (color saturation) is likely to occur (extremely brightly lit or shiny parts) are displayed with diagonal lines (zebra pattern A). Marker display: Displays the luminance level of the center of the screen (luminance display frame B) in %. It makes the adjustment of the brightness of the object easier, by checking the luminance level of the object, when recording same object in different surroundings. Luminance level C is displayed between 0% and 99%. It will be displayed as 99% when it is

over 99%.

This function is not available in the following cases: j When [WFM] is set to [ON] (l 87, 155) j During Freeze Frame (l 81)

Fast Zoom

EVF ON/OFF

Auto Iris Level

Zebra

(When Zebra 1 is set) (When Marker is set)

99%

- 88 -

You can record an image with little white saturation if you manually adjust the shutter speed or brightness not to display zebra pattern. (l 59, 63)

The zebra pattern does not appear on the images actually recorded. It is also possible to adjust the level of the zebra pattern to be displayed. (l 171) It is also possible to change the [ZEBRA MODE] setting to change the display time for the zebra

pattern display. (l 155)

Register Optical Image Stabilizer to a USER button. (l 74) This enables/disables the Image Stabilizer. (l 42)

Register Scene File to a USER button. (l 74) You can save the scene number settings of [CUSTOMIZE SCENE] to the SD card or load them from the SD card to this unit.

Saving custom scene settings 1 Press USER button or touch USER button icon in the recording screen. 2 Touch [SAVE]. 3 Touch the name of the scene file. All scene number settings will be saved. Up to 8 files can be saved. If you have touched the name of the existing scene file, touch [YES] to overwrite it. 4 Touch [EXIT] to complete the setting.

Assigning saved scene files to custom scenes 1 Press USER button or touch USER button icon in the recording screen. 2 Touch [LOAD]. 3 Touch the name of the scene file you want to load. 4 Touch the scene number to which you want to assign the scene file. Settings of the scene number you have touched will be loaded, and then assigned to the

corresponding scene number in [CUSTOMIZE SCENE]. If you touch [ALL], settings of all scene numbers will be loaded. 5 Touch [EXIT] to complete the setting.

You can also access this function by selecting menu items. [SCENE FILE] # [SCENE FILE] # [LOAD] or [SAVE]

Optical Image Stabilizer

Scene File

- 89 -

Register Auto Rec to a USER button. (l 74) This enables/disables a function that controls recording performed with an external device (recorder, etc.) connected to the SDI OUT terminal. 1 Select the [SDI REMOTE] menu.

2 Select the [REMOTE REC LINK] menu.

3 Press USER button or touch USER button icon in the recording screen. When is displayed, signals will be transmitted, prompting the external device to start

recording. To stop the recording being performed with the external device, press the applicable USER

button or touch the applicable USER button icon again. When is displayed, signals will be transmitted, prompting the external device to stop the recording.

When [HDMI TC OUTPUT] is set to [ON], you can also control recording performed with an external device connected to the HDMI OUT terminal.

It is not possible to control recording performed with an external device connected to the SDI OUT terminal in the following cases: j When [REC FORMAT] is set to [SA 480/59.94i] or [SA 576/50.00i] (l 142) j When [RESOLUTION] is set to [DOWN CONV.] (l 115)

Register AF area width adjustment to a USER button. (l 74) You can adjust the area width where Auto Focus works according to the size of the subject. (l 47) 1 Press USER button or touch USER button icon in the recording screen. are displayed on the screen. 2 Rotate the jog dial to adjust the AF area

frame.

Auto Rec

: [OUTPUT SETUP] # [SDI REMOTE] # [ON]

: [OUTPUT SETUP] # [REMOTE REC LINK] # [OFF]

AF area width adjustment

MENU

MENU

A [AF AREA] B AF area frame

AF-AREA

- 90 -

3 Push the jog dial to finish the adjustment. Press USER button or touch the USER button icon to cancel the setting. To adjust the AF area frame again, press the jog dial while the on-screen

icon [ AF AREA] (yellow) is displayed, and repeat Steps 2s3. For information on on-screen icons, refer to 99.

This enables/disables Variable Frame Rate (VFR) Mode. In Variable Frame Rate Mode, you can record quick or slow motion picture by changing the frame rate before recording.

Slow motion (overcrank recording) Used in scenes such as climaxes, a slow motion effect creates a dramatic impression. Set a frame rate that provides more frames than the frame rate in [REC FORMAT] does. Example: If you set [FHD 1080/23.98p 50M] to 48fps and record a motion picture, a slow motion effect of 1/2 can be gained.

Quick motion (undercrank recording) A fast motion effect is used in scenes showing the flow of clouds, people standing in the middle of crowds, etc. Set a frame rate that provides less frames than the frame rate in [REC FORMAT] does. Example: If you set [FHD 1080/23.98p 50M] to 12 fps and record a motion picture, a quick motion effect of 2k can be gained.

Register VFR mode to a USER button. (l 74) Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) Make the [REC MODE] and [REC FORMAT] settings. (l 141, 142) Variable Frame Rate Mode is available for the following [REC MODE] and [REC FORMAT]

settings:* * When the size for [REC FORMAT] is set to FHD (1920k1080) and a frame rate other than 59.94i

and 50.00i is set for [REC FORMAT], a [REC FORMAT] setting with a bit rate of 50 Mbps will be selected automatically.

VFR mode

System frequency setting Recording mode Recording format

59.94Hz MOV, MP4

FHD 1080/59.94p 50M, FHD 1080/29.97p 50M, FHD 1080/23.98p 50M

50.00Hz FHD 1080/50.00p 50M, FHD 1080/25.00p 50M

- 91 -

1 Press USER button or touch USER button icon in the recording screen. [VFR] will be displayed. The frame rate display will change.

/ will be displayed. Audio is not recorded during recording. 2 Rotate the jog dial to change the frame rate. You can set a frame rate between 2 and 120. Some frame rates cannot be set depending on the

[REC FORMAT] setting. Push the jog dial to set the frame rate. If you start recording before pushing the jog dial, the

setting will not be applied. 3 Press the recording start/stop button to start recording. When recording in Variable Frame Rate Mode for the first time since you turned on this unit, a

message is displayed, informing you that audio cannot be recorded.* * Audio is recorded when the number of frames for the frame rate in [REC FORMAT] and the

number of frames for Variable Frame Rate Mode are the same. The frame rate cannot be changed during recording. 4 Press the recording start/stop button again to stop recording. To cancel Variable Frame Rate Mode, press USER button, or touch USER button icon.

Frame rates and their effects Quick motion (undercrank) or slow motion (overcrank) recording is possible with the following frame rate settings: When you set the frame rate to 100 fps or 120 fps, the angle of view will change. (The color of the

frame rate value will change to blue.)

(Example) A Frame Rate (fps) B Frame rate in [REC FORMAT]

[REC FORMAT] Available frame rates [FHD 1080/59.94p 50M] 2 fps to 58 fps 60 fps 62 fps to 120 fps [FHD 1080/29.97p 50M] 2 fps to 28 fps 30 fps 32 fps to 120 fps [FHD 1080/23.98p 50M] 2 fps to 22 fps 24 fps 26 fps to 120 fps [FHD 1080/50.00p 50M] 2 fps to 48 fps 50 fps 52 fps to 120 fps [FHD 1080/25.00p 50M] 2 fps to 23 fps 25 fps 27 fps to 120 fps

Effect on playback

Quick motion (The smaller the value

is, the faster the playback becomes.)

Normal

Slow motion (The larger the value

is, the slower the playback becomes.)

Audio recording No Yes No

12 : 23.98p

ALC A.REC

- 92 -

You can also enable/disable Variable Frame Rate Mode or change the frame rate using the menu. j [VFR MODE] (l 131) j [FRAME RATE] (l 131)

Variable Frame Rate Mode is set to [OFF] in following cases: j When the [REC MODE] or [REC FORMAT] setting is changed to a setting that does not

support Variable Frame Rate Mode j When the [REC FORMAT] setting is changed to a setting with a different frame rate

This function is not available in the following cases: j When you set [OUTPUT BITS] to [4:2:2(10bit)] j When [2 SLOTS FUNC.] is set to [DUAL CODEC] (l 159)

The following functions are canceled: j Flash band compensation (l 86, 140) j Relay recording (l 159) j Background recording (l 160) j Interval Recording (l 162) j PRE-REC (l 86, 163) j Hybrid Optical Image Stabilizer (l 42)

j Area Mode (l 82) j Focus Transition (l 52) j Digital Zoom (l 79) j Infrared Recording mode (l 84, 164) j Custom AF function (l 46) j i.Zoom (l 41)

[BLACK FADE] and [WHITE FADE] are disabled. (l 78) Still picture recording cannot be used. Even if you press the recording start/stop button as soon as recording has started, it may take

some time until the recording stops. The screen may momentarily black out when the frame rate is changed in Step 2. The maximum continuous recordable time for one scene in Variable Frame Rate Mode varies

depending on the set frame rate. Recording stops when a certain time has elapsed since the start of the recording, and restarts automatically a few seconds later. j When recording in slow motion: 10 hours j When recording with the same frame rate as the frame rate in [REC FORMAT]: 10 hours j When recording in quick motion, the recordable time becomes shorter than 10 hours

depending on the ratio between the frame rate for [REC FORMAT] and variable frame rate setting.

Example: When [REC FORMAT] is set to [FHD 1080/59.94p 50M]

h is an abbreviation for hour.

Variable frame rate setting Maximum continuous recordable time for one scene

2 fps 10 h

60 fps 120 fps 5 h

- 93 -

Register Focus Macro to a USER button. (l 74) You can enable/disable Focus Macro. is displayed on the screen when [ON] is selected.

Register i.Zoom to a USER button. (l 74) You can enable/disable i.Zoom.

When [V-Log L MODE] is selected, you can temporarily display images in REC.709 color space. Register Log View Assist to a USER button. (l 74) Set [V-Log L MODE] to [ON]. (l 140)

Press and hold the USER button, or touch and hold the USER button icon in the recording screen. It will be canceled when the button is released.

Log View Assist is canceled in the following cases: j When starting motion picture recording j When PRE-REC is set (l 86, 163) j When Background recording (l 160)

Register LCD/EVF Output to a USER button. (l 74) This changes how to turn on/off the LCD monitor and Viewfinder. (l 24)

Register Menu to a USER button. (l 74) The menu can be displayed.

Focus Macro

i.Zoom

Log View Assist

LCD/EVF Output

Menu

- 94 -

Color Bar Screen

To cancel, press the BARS button again. It will be canceled when the unit is turned off. While the color bar is displayed, a test tone will be output from the headphone terminal, HDMI

terminal, SDI OUT terminal and AUDIO OUT terminal. It will not be output from the speaker of this unit.

Different color bars are displayed depending on the [BARS TYPE] setting. (l 156) The frequency of a test tone that is output when color bars are displayed differs depending on the

setting of the following items: j [SYSTEM FREQ] (l 141) j The frame rate in [REC FORMAT] or [OUTPUT FORMAT] (l 142, 147)

The test tone volume differs depending on the [TEST TONE] setting. (l 170) You can record color bars as motion pictures, but not as still pictures. If you press the BARS button while recording color bars as a motion picture, you can stop

displaying the color bars. To display them again, stop the recording and press the BARS button.

Recording

Useful functions

BARS button Press the BARS button to output a color bar screen to an external monitor so you can adjust them.

System Frequency setting Frame rates Test tone

frequency

59.94Hz All frame rates 1 kHz

50.00Hz 24.00p

50.00p/50.00i/25.00p 997 Hz

A BARS button B ND FILTER switch C DISP/MODE CHK switch

- 95 -

ND filter Using the ND filter switch, you can switch the built-in optical ND filter setting. (The filter adjusts the amount of light.) Use this function when recording a bright subject outdoors under a clear sky that causes the

screen to look white.

Slide the ND filter switch.

If the selected setting 1/64, 1/16 or 1/4 does not match an ND filter setting recommended by this unit, the recommended setting will be displayed on the screen, blink for approximately 5 seconds and disappear.

A recommend ND filter setting may not be displayed correctly in scenes that are too dark.

Switching the screen indications/mode information display

* When [DATE/TIME] is set to [TIME], [DATE], or [DATE&TIME] To cancel the setting, set the DISP/MODE CHK switch to ON.

1/64: Reduces the amount of light to 1/64.

1/16: Reduces the amount of light to 1/16.

1/4: Reduces the amount of light to 1/4.

OFF: Does not use the ND filter.

DISP/MODE CHK switch When the DISP/MODE CHK switch is set to OFF, all screen displays disappear, except for the counter display, time stamp display*, zebra pattern display, marker display, and safety zone display. (l 181)

ND1/64

ND1/16

A ND filter setting B Recommended ND filter setting

- 96 -

To display the Mode Information Each time you set the DISP/MODE CHK switch from ON to CHK, the mode information display switches in the following order:

Mode information display1 # Mode information display2 # Mode information display3 # Normal display

You can use convenient functions just by the easy operation of touching the screen.

1 Touch the LCD monitor in the recording screen.

The operation icons are displayed.

2 Touch an operation icon. The following function is available. Refer to the respective

pages for the operation.

* It is not displayed when [i.Zoom] is set to [OFF].

If you touch the screen while an operation icon is being displayed or do not touch the icon for a certain period, it will disappear. To display again, touch the screen.

Mode information display1: Displays the list of functions assigned to the USER buttons (USER1 to 8).

Mode information display2: Displays the settings assigned to the GAIN switch ([GAIN L]/ [GAIN M]/[GAIN H]), White Balance modes assigned to the WHITE BAL switch ([WHITE BAL A]/[WHITE BAL B]/[WHITE BAL PRST]), and the [SUB REC BUTTON] and [SUB ZOOM] settings.

Mode information display3: Displays the settings for [OUTPUT SEL], [OUTPUT BITS], [SDI REMOTE], [REMOTE REC LINK], [HDMI TC OUTPUT] and [CAMERA NUMBER].

Recording

Using Operation Icons

, etc. Customize Scene (l 130)

, etc. USER Button Icon (l 74)

/ i.Zoom Button Icon (l 41)*

SCN1 SCN2 SCN3 SCN4 SCN5 SCN6

MENU

ATW DRS PRE-REC

SCN1 SCN2

PRE-REC MENU

- 97 -

You can select and set menu items (l 30), etc. using the jog dial.

1 Rotate the jog dial on the menu screen, etc., to move the cursor.

The selected item will be displayed in yellow.

2 Push the jog dial to set.

Menu operations for setting a value When a menu that lets you set a value is displayed, select the value display before adjusting the setting. You cannot select / / / with the jog dial when a screen that lets you adjust a value is

displayed.

(Example: When adjusting the brightness for [LCD SET])

1 Rotate the jog dial to move the cursor to the value display A.

Push the jog dial to select the value display. 2 Rotate the jog dial to adjust the setting. Pushing the jog dial will set the value you have selected.

The jog dial also allows you to select/set operation icons, thumbnails, etc. Parts that are finger-touch sensitive can be operated with the jog dial. (Excluding some functions)

Recording

Using of jog dial

Selecting/setting items

A Jog dial

- 98 -

You can select the following functions and adjust their settings using the jog dial. You can also switch between the functions and adjust their settings.

(When the recording screen is displayed)

(When the playback screen is displayed)

Using the multi manual function

On-screen icons Functions Settings

GAIN Gain adjustment (l 61) Adjusts the gain value.

VAR VAR adjustment (l 58) Adjusts the VAR setting of the White Balance.

AF AREA AF Area Range Adjustment (l 47)

Adjusts the size of the AF area frame.

VFR Variable Frame Rate (l 91) Changes the frame rate for Variable Frame Rate Mode.

SHUTTER Shutter speed (l 63) Adjusts the shutter speed.

AREA Area Mode (l 82) Changes the area frame setting.

ASSIST Focus Assist (l 48) Changes the magnification level of the magnified display

VOLUME Headphone Volume Adjustment (l 100)

Adjusts the headphone volume.

ICONS Allows you to display/select operation icons on the recording screen.

s

On-screen icons Functions Settings

VOLUME Volume adjustment (l 103) Adjusts the speaker and headphone volume during motion picture playback.

ICONS Allows you to display/select operation icons on the playback screen.

s

- 99 -

To change the function you adjust 1 Change settings in advance so that you can select more than two functions. Change settings as follows:

The on-screen icon for the selected function is displayed in white. (Function Execution Mode) If you have selected [ ICONS], you can rotate the jog dial to select an operation icon.

2 Push the jog dial. The on-screen icon turns yellow. (Function Selection Mode) 3 Rotate the jog dial to select the function you want to adjust, and press the jog

dial to set the selection. The on-screen icon for the selected function turns white. (Function Execution Mode) You can rotate the jog dial to adjust the setting of the selected function.

Headphone Volume Adjustment Adjust the volume of the headphone while recording. Set [VOLUME] to [ON]. (l 170) 1 Connect headphones to the headphone

terminal. 2 Rotate the jog dial to adjust the volume. Actual volume to be recorded does not change. 3 Push the jog dial to finish the adjustment.

You can also adjust the volume by touching / in Step 2. Not performing touch operations after the adjustment allows you to exit the setting.

Functions Settings to be changed in advance

Gain adjustment Switch to Manual Mode. (l 36)

VAR adjustment Set the WHITE BAL switch to PRST, and press the AWB button to set the White Balance mode to [VAR]. (l 55)

AF Area Range adjustment Press the applicable USER button to enable [AF AREA WIDTH] or select menu items to set [AF AREA WIDTH] to [SET]. (l 47, 90)

Variable Frame Rate Press the applicable USER button to enable [VFR MODE] or select menu items to set [VFR MODE] to [ON]. (l 91, 131)

Shutter speed Press the SHUTTER button to enable Manual Shutter Mode. (l 63)

Area Mode Press the applicable USER button to enable Area Mode. (l 82)

Focus Assist Set [FOCUS ASSIST] to [EXPAND] or [BOTH], and press FOCUS ASSIST button to enable Focus Assist. (l 48)

Headphone Volume Adjustment Connect headphones to this unit.

A [VOLUME]

- 100 -

1 Set this unit to playback mode. (l 23) 2 Touch the play mode select icon A.

3 Select the media C you wish to play back.

4 (To set this unit to Motion Picture Playback Mode) Touch the desired recording mode D and recording format E for playback.

Recording mode options with recorded scenes are displayed in green.

The available recording format options differ depending on [SYSTEM FREQ] (l 178) or the recording mode option you have touched.

Touch [ENTER]. A recording mode icon B will be displayed on the thumbnail display. ( / / ) (If you have touched the recording mode option [MOV] or [MP4])

After you have touched a recording format option, one of the following icons will be displayed on each thumbnail. The icon to be displayed differs depending on the size of recording format. j : Scenes recorded in 4K (4096k2160) j : Scenes recorded in UHD (3840k2160) j : Scenes recorded in FHD (1920k1080) j : Scenes recorded as sub recordings with [DUAL CODEC REC] set to [FHD 50Mbps]

(l 159, 161) j : Scenes recorded as sub recordings with [DUAL CODEC REC] set to [FHD 8Mbps]

(l 159, 161) (If you have touched the recording mode option [AVCHD])

After you have touched a recording format option, one of the following icons will be displayed on each thumbnail. j : Scenes recorded in [PS 1080/59.94p]/[PS 1080/50.00p] j : Scenes recorded in [PH 1080/59.94i]/[PH 1080/23.98p]/[PH 1080/50.00i] j : Scenes recorded in [HA 1080/59.94i]/[HA 1080/50.00i] j : Scenes recorded in [HE 1080/59.94i]/[HE 1080/50.00i] j : Scenes recorded in [PM 720/59.94p]/[PM 720/50.00p] j : Scenes recorded in [SA 480/59.94i]/[SA 576/50.00i]

Playback

Motion picture/Still picture playback

10

UHD

13

16

11

14

17

12

15

18

UHD UHD

UHD UHD UHD

UHD UHD UHD

4K UHD FHD DU50

DU8

PS PH HA HE PM

SA

- 101 -

(To set this unit to Still Picture Playback Mode) Touch the still picture (JPEG) F.

5 Touch the scene or the still picture to be played back.

Next (Previous) page can be displayed by touching / .

6 Select the playback operation by touching the operation icon.

* When touched twice, the fast forward/fast rewind speed increases. (Screen display will change to / .)

G Operation icon

If you touch the screen while an operation icon is being displayed or do not touch the icon for a certain period, it will disappear. To display again, touch the screen.

Motion picture playback Still picture playback

1/;: Playback/Pause 6: Fast rewind playback* 5: Fast forward playback* : Stops the playback and shows the

thumbnails.

1/;: Slide show (playback of the still pictures in numerical order) start/ pause.

2;: Plays back the previous picture. ;1: Plays back the next picture. : Stops the playback and shows the

thumbnails.

10

UHD

13

16

11

14

17

12

15

18

UHD UHD

UHD UHD UHD

UHD UHD UHD

TC 00:02:30.00

- 102 -

Change the thumbnail display While the thumbnail is displayed, the thumbnail display changes in the following order if the zoom lever or the sub zoom lever is operated to side or side.

* Detailed information of the scene is displayed when playing back motion pictures. Following information is displayed. START TC, START UB, and DURATION are displayed only for AVCHD scenes. j START TC j START UB j DATE j TIME ZONE

j DURATION j REC MODE j FORMAT

If you press the THUMBNAIL button to switch between Recording Mode and Playback Mode, the thumbnails of 9 scenes will be displayed.

By displaying in 1 scene, recording date and time are displayed when playing back motion pictures, and recording date and file number when playing back still pictures.

Speaker/Headphone volume adjustment Operate the volume lever, sub zoom lever or jog dial to adjust the speaker/headphone volume during Motion Picture Playback Mode. Adjusting the volume with the volume lever/sub zoom lever

Adjusting the volume with the jog dial

1 Push the jog dial while [ VOLUME] is displayed.

( side) ( side)

20 scenes () 9 scenes () 1 scene () Scene information display*

T

W

T

W

Towards r: Increases the volume

Towards s: Decreases the volume

A [VOLUME]

T

W

T

W

A Jog dial

- 103 -

2 Rotate the jog dial to adjust the volume.

3 Push the jog dial to finish the adjustment.

Sound will be heard only during normal motion picture playback. If pause play is continued for 5 minutes, the screen returns to the thumbnails. In the following cases, when you select the desired recording format for playback, this unit will be

restarted to switch the system frequency: j When you have switched recording format from [4K/24.00p] to a different option. j When you have switched recording format from an option other than [4K/24.00p] to [4K/24.00p]

If you set recording mode to [AVCHD] and recording format to [ALL AVCHD] and play back a scene, the screen may turn dark momentarily when it switches to another scene.

B [VOLUME]

Motion picture compatibility This unit is based on AVCHD Progressive/AVCHD. Even if the devices used have compatible standards, when playback of video recorded using

another device is performed using this device, or when video recorded using this device is played back in another device, playback may not proceed normally, or may not be possible. (Please check compatibility in the instruction manual of your device.)

Motion pictures recorded with devices other than this unit are not supported by this unit.

Still picture compatibility This unit is compliant with the unified standard DCF (Design rule for Camera File system)

established by JEITA (Japan Electronics and Information Technology Industries Association). The file format of still pictures supported by this unit is JPEG. (Not all JPEG formatted files

will be played back.) This unit may degrade or not play back still pictures recorded or created on other products

and other products may degrade or not play back still pictures recorded on this unit. Depending on the playback device, still pictures may be played back with picture sizes

different from the ones with which they were recorded.

- 104 -

Motion picture playback using operation icon For details on the basic playback operations, refer to page 101.

Playback operation Playback display Operating steps

Skip playback (to the start of a

scene)

During Playback Touch the LCD monitor and slide from right to left (from left to right) during playback.

Slow-motion Playback

During Pause

With the playback paused, continue touching .

( is for slow rewind playback.) Playback is slow while touching. Normal playback is restored when you touch

. When AVCHD scenes are played back in

reverse slow-motion, they will be shown continuously at approximately 2/3rd the speed of normal playback (at 0.5 second intervals).

MOV/MP4 scenes are played back as follows: j Scenes recorded with [REC FORMAT] set to

[FHD 1080/59.94p ], [FHD 1080/29.97p ], [FHD 1080/50.00p ], [FHD 1080/

25.00p ], [FHD 1080/23.98p ]: Reverse slow-motion playback at 1 second intervals

j Scenes recorded with [REC FORMAT] set to an option other than the above: Reverse slow-motion playback at 0.5 second intervals

Frame-by-frame Playback

During Pause With the playback paused, touch . (Touch to advance the frames one at a time in the reverse direction.) Normal playback is restored when you touch

. Frames are played back at 0.5 second intervals

during reverse frames-by-frame playback.

Direct playback

During Playback Touch the direct playback bar A or slide it while touching. The playback pauses temporarily and skips to

the position touched or slid to while touching. Playback will start by releasing your touching or

sliding finger.

- 105 -

Creating still picture from motion picture You can save a frame of a recorded motion picture as a still picture. The picture size with which a still picture will be recorded differs depending on the picture size of [REC FORMAT] with which the motion picture was recorded.

While playing back a motion picture, touch the at the scene you want to save it as a still

picture. If you register [CAPTURE] to any of the USER buttons

1s8, you can capture a still picture by pressing the USER button. For information on how to register functions to the USER buttons, refer to page 74.

It is convenient to use Pause, Slow-motion Playback and Frame-by-frame Playback. Date the motion picture was recorded will be registered as date of the still picture. Quality will be different from the normal still picture.

Please refer to page 202 about approximate number of recordable pictures.

Playback

Useful functions

Recording format Aspect ratio Picture size [REC FORMAT] setting with a size of 4K (4096k2160) 17:9 4096k2160

[REC FORMAT] setting with a size of UHD (3840k2160)

16:9

3840k2160

[REC FORMAT] setting with a size of FHD (1920k1080)

1920k1080 [PS 1080/59.94p]/[PS 1080/50.00p]/ [PH 1080/59.94i]/[PH 1080/23.98p]/ [PH 1080/50.00i]/ [HA 1080/59.94i]/[HA 1080/50.00i]/ [HE 1080/59.94i]/[HE 1080/50.00i]

[PM 720/59.94p]/[PM 720/50.00p] 1280k720

M8.8

M8.3

2.1 M

M0.9

TC 00:02:30.00

- 106 -

Repeat Playback Playback of the first scene starts after playback of the last scene finishes. Select the menu.

The indication appears on the full screen views. All the scenes displayed in the thumbnail will be repeatedly played back.

Repeat Playback cannot be used for the slide show playback of the still pictures. (l 102)

Resuming the previous playback If playback of a scene was stopped halfway, the playback can be resumed from where it was stopped. Select the menu.

If playback of a motion picture is stopped, appears on the thumbnail view of the stopped scene.

The memorized resume position is canceled if you turn off the unit or press the THUMBNAIL button. (The setting of [RESUME PLAY] does not change.)

: [VIDEO SETUP] # [REPEAT PLAY] # [ON]

: [VIDEO SETUP] # [RESUME PLAY] # [ON]

MENU

MENU

- 107 -

Playing back scenes or still pictures by date The scenes or still pictures recorded on the same day can be played back in succession.

1 Touch the date select icon.

2 Touch the playback date. The scenes or still pictures recorded on the date selected are displayed as thumbnails.

3 Touch the scenes or still picture to be played back.

If you press the THUMBNAIL button to switch between Recording Mode and Playback Mode, the thumbnails of all scenes will be displayed.

In cases such as those described below, scenes and still pictures are grouped separately on the date list, and 1, 2 may be added after the date: j When the number of scenes exceeds 99 j When the number of still pictures exceeds 999 j When you change the [REC FORMAT] setting (l 142) j When you set [REC MODE] to [AVCHD] and set Interval Recording to an option other than

[OFF] (l 162) j When you set [REC MODE] to [MOV] or [MP4] and change the system frequency (l 141) j When [NUMBER RESET] is performed (l 178)

Scenes recorded with the following [REC FORMAT] settings are grouped separately on the date list. A recording format icon will be displayed next to the date.

is displayed after the date in the list by date for the still pictures created from the motion picture. (l 106)

Recording format Icon to be displayed [REC FORMAT] setting with a size of 4K (4096k2160) [REC FORMAT] setting with a size of UHD (3840k2160) [REC FORMAT] setting with a size of FHD (1920k1080) Scenes recorded as sub recordings with [DUAL CODEC REC] set to [FHD 50Mbps] (l 159, 161) Scenes recorded as sub recordings with [DUAL CODEC REC] set to [FHD 8Mbps] (l 159, 161) [PS 1080/59.94p]/[PS 1080/50.00p] [PH 1080/59.94i]/[PH 1080/23.98p]/[PH 1080/50.00i] [HA 1080/59.94i]/[HA 1080/50.00i] [HE 1080/59.94i]/[HE 1080/50.00i] [PM 720/59.94p]/[PM 720/50.00p] [SA 480/59.94i]/[SA 576/50.00i]

A Date select icon

10

UHD

13

16

11

14

17

12

15

18

UHD UHD

UHD UHD UHD

UHD UHD UHD

4K

UHD

FHD

DU50

DU8

PS

PH

HA

HE

PM

SA

- 108 -

Press the THUMBNAIL button to switch this unit to the Playback Mode. (l 23) To delete the scene or still picture being played back

Touch while scenes or still pictures to be deleted are being played back.

To delete scenes or still pictures from the thumbnail display Switch to the thumbnail display of the scenes or still pictures to delete. (l 101)

1 Select the menu.

Protected scenes/still pictures cannot be deleted.

2 (When [MULTI] is selected in Step 1) Touch the scene/still picture to be deleted.

When touched, the scene/still picture is selected and the indication appears on the thumbnail. Touch the scene/still picture again to cancel the operation.

Up to 99 scenes can be selected to be deleted.

(When [SINGLE] is selected in Step 1) Touch the scene/still picture to be deleted.

3 (When [MULTI] is selected in Step 1) Touch [Delete].

To continuously delete other scenes/still pictures, repeat Steps 2-3.

Editing

Deleting scenes/still pictures Deleted scenes/still pictures cannot be restored, so perform appropriate confirmation of the contents before proceeding with deletion.

: [VIDEO SETUP] or [PICT. SETUP] # [DELETE] # desired setting

[ALL SCENES]: All the scenes or still pictures displayed as thumbnails can be deleted. (When playing back scenes or still pictures by date, all scenes or still pictures of the selected date will be deleted.) [MULTI]: Multiple scenes or still pictures can be selected and deleted. [SINGLE]: Single scene or still picture can be selected and deleted.

TC 00:02:30.00

MENU

- 109 -

When you stop deleting halfway: Touch [CANCEL] or press MENU button while deleting. The scenes or still pictures that have already been deleted when the deletion is canceled cannot

be restored.

To complete editing: Touch [Return] or press MENU button.

Scenes/still pictures that cannot be played back (the thumbnails are displayed as ) cannot be deleted.

In case of [ALL SCENES], the deletion may take time if there are many scenes or still pictures. If you delete scenes recorded on other products or still pictures conforming to DCF standard with

this unit, all the data related to the scenes/still pictures may be deleted. When still pictures recorded on an SD card by other products are deleted, a still picture (other

than JPEG) that cannot be played back on this unit, may be erased.

Protecting scenes/still pictures

Scenes/still pictures can be protected so that they are not deleted by mistake. (Even if you protect some scenes/still pictures, formatting the SD card will delete them.) Press the THUMBNAIL button to switch this unit to the Playback Mode. (l 23)

1 Select the menu.

2 Touch the scene/still picture to be protected. When touched, the scene/still picture is selected and the indication appears on the

thumbnail. Touch the scene/still picture again to cancel the operation. Touch [Return] to complete the settings.

: [VIDEO SETUP] or [PICT. SETUP] # [SCENE PROTECT]MENU

- 110 -

Motion pictures or still pictures recorded with this unit can be copied between SD Cards inserted in this unit. Copying is not possible if the type of the source SD card (SDHC Memory Card/SDXC Memory

Card) is different from that of the target SD card. Check the used space of the copy destination It is possible to check the used space of the SD Card by [MEDIA STATUS]. (l 176) By displaying in 1 scene, recording date and time can be checked when playing back motion

pictures, and recording date and file number when playing back still pictures. Depending on the media condition, some remaining capacity of the SD Card may not be used.

1 Press the THUMBNAIL button to switch this unit to the Playback Mode. Use a sufficiently charged battery or the AC adaptor.

2 Select the menu.

3 Touch desired items following the screen display. It will return to the previous step by touching [Return]. (When [SELECT SCENES] is selected)

When touched, the scene/still picture is selected and the indication appears on the thumbnail. Touch the scene/still picture again to cancel the operation.

(When [SELECT DATE] is selected) When touched, the date is selected and surrounded by red. Touch the date again to cancel the operation.

Up to 99 scenes/still pictures or 99 dates can be set in succession.

4 Touch [EXIT] when the copy complete message is displayed. The thumbnail view of the copy destination is indicated.

When you stop copying halfway Touch [CANCEL] while copying.

Editing

Copying between SD cards

Copying

: [COPY] # [SELECT COPY]

[ ]: Copies from card 1 to card 2

[ ]: Copies from card 2 to card 1

[ ]*: Copies from card 1 to an external media device

[ ]*: Copies from card 2 to an external media device

* Displayed only when the external media is connected. (l 125)

MENU

- 111 -

Depending on the following conditions, the time it takes for copying may be longer. j The number of recorded scenes is large.

If some motion pictures or still pictures have already been recorded to the copy destination, then the same date may be assigned or images may not display by date when the list by date is selected.

Motion pictures that have been recorded on another device may not be copied. Data recorded on a PC cannot be copied.

The settings for the copied motion pictures and still pictures will be cleared if the protected motion pictures or still pictures are copied.

The order in which the scenes or still pictures were copied cannot be changed.

If you will delete the motion pictures or still pictures after copying is complete, be sure to play back the motion pictures or still pictures to check that they have been copied to correctly before deleting.

- 112 -

Headphones You can connect headphones (commercially-available) to the headphone output jack (3.5 mm (0.14 q) diameter stereo mini jack).

Sound is not output from the speaker when headphones are connected.

Remote control

You can connect a remote control (commercially-available) to either of the CAM REMOTE terminals (FOCUS IRIS or ZOOM S/S). Connecting a remote control to the FOCUS IRIS terminal (3.5 mm (0.14 q) diameter mini jack)

allows you to remotely control the focus and iris. Connecting a remote control to the ZOOM S/S terminal (2.5 mm (0.1 q) diameter super-mini jack)

allows you to remotely control the zoom and start/stop recording.

Do not connect any device other than a remote control to the CAM REMOTE terminals. Doing so may change the image brightness or cause the image to be out of focus.

(When a remote control is connected to the FOCUS IRIS terminal) Priority for iris adjustment is given to the remote control. It is not possible to adjust the iris with the

iris ring of this unit. If you switch to Auto Mode when [A.IRIS] is set to [ON], the remote control cannot be used.

Linking to external devices

Connecting Headphones, a Remote Control or an External Monitor

A Headphone output jack

B FOCUS IRIS terminal C ZOOM S/S terminal

- 113 -

External monitor You can connect this unit to an external monitor as shown in the figure below.

By connecting this unit to a 4K-compatible external monitor with HDMI Cable and play back scenes recorded with their size set to 4K (4096k2160) or UHD (3840k2160) in [REC FORMAT], you can enjoy finely-detailed 4K motion pictures. For an external monitor that does not support 4K motion picture, you can change the [RESOLUTION] or [HDMI UHD OUTPUT LIMIT] setting so that 4K motion pictures can be played back at a lower resolution.

If you set [REC FORMAT] to [UHD 2160/59.94p 150M] or [UHD 2160/50.00p 150M] in Recording Mode and then connect this unit to a 4K-compatible external monitor with an HDMI cable, images will be output in 3840k2160 when recording is stopped and in 1920k1080 during recording or PRE-REC. Please note that the image on the screen of this unit and on the external monitor disappears for a few seconds every time you start or stop recording or every time you switch the PRE-REC on/off. These irregularities do not occur when [RESOLUTION] is set to [1080p] or [1080i], which outputs images in 1920k1080.

This unit is not compatible with the VIERA Link. Use a commercially-available High Speed HDMI cable.

If possible, we recommend using a cable with a length of 3 m (9.84 feet) or less. Use a commercially-available, double-shielded BNC cable equivalent to 5C-FB.

When connecting with an HDMI cable using an HDMI-to-DVI converter, etc., be sure to connect the HDMI cable to the connector of this unit last. Connecting the HDMI cable to the connector of this unit first may result in malfunction.

AUDIO OUT

VIDEO OUT

SDI OUT

A HDMI Cable (optional) B BNC Cable (commercially-available) C Audio cable (commercially-available)

3.5 mm (0.14 q) diameter jack to RCA cable D External monitor

- 114 -

If you connect this unit to the external monitor when this unit is set to Recording Mode, a squealing sound* may be output. Before connecting this unit, set it to Playback Mode.

* The microphone may pick up the sound from the speakers, producing an abnormal sound. When the external monitor is connected via the VIDEO OUT terminal of this unit, even if you set

[RESOLUTION] to [DOWN CONV.], scenes in the recording format [4K 2160/24.00p 100M] cannot be output.

To display the on-screen information on the external monitor When the menu setting is changed, the information displayed on the screen (operation icon and Counter display etc.) can be displayed/not displayed on the external monitor. (In Recording Mode)

Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31)

This item is set to [OFF] in the following situations when this unit is in Recording Mode: j When [OUTPUT BITS] is set to [4:2:2(10bit)] j When [REC FORMAT] is set to a setting with a size of 4K (4096k2160) or UHD (3840k2160)

(l 142) j During auto recording (l 90, 168)

Setting the external output resolution When connecting this unit to an external monitor or other external device (recorder, etc.), select the settings below that match the terminal to be used.

1 Select the [OUTPUT SEL] menu.

2 Select the [RESOLUTION] menu.

[SYSTEM] automatically sets the output resolution according to the setting in [REC FORMAT] or [OUTPUT FORMAT]. If the images are not output on the external device when the setting is [SYSTEM], switch to the method [1080p], [1080i] or [DOWN CONV.] which enables the images to be displayed on your external device. (Please read the operating instructions for the external device.)

[DOWN CONV.] outputs images in standard picture quality.

: [DISP SETUP] # [VIDEO OUT OSD] # [ON] or [OFF]

: [OUTPUT SETUP] # [OUTPUT SEL] # desired setting

[HDMI]: Select this setting when connecting to the HDMI OUT terminal.

[SDI]: Select this setting when connecting to the SDI OUT terminal.

[SDI+AV]: Select this setting when connecting to the VIDEO OUT terminal.

: [OUTPUT SETUP] # [RESOLUTION] # desired setting

[SYSTEM]/[1080p]/[1080i]/[DOWN CONV.]

MENU

MENU

MENU

- 115 -

When [OUTPUT BITS] (l 31) is set to [4:2:2(10bit)], following settings are not available: j [OUTPUT SEL] is set to [SDI+AV]. j [RESOLUTION] is set to [DOWN CONV.].

When [REC FORMAT] or [OUTPUT FORMAT] is set to [4K 2160/24.00p 100M], following settings are not available: j [OUTPUT SEL] is set to [SDI+AV]. j [RESOLUTION] is set to [1080i] or [DOWN CONV.].

When [REC FORMAT] is set to [SA 480/59.94i] or [SA 576/50.00i], [RESOLUTION] is fixed to [SYSTEM].

When [OUTPUT SEL] is set to [SDI+AV], [RESOLUTION] is fixed to [DOWN CONV.]. [RESOLUTION] cannot be set during Freeze Frame. (l 81) Images may not be displayed on the external device for several seconds in some cases, such as

when changing between scenes.

Depending on the [RESOLUTION] setting and connected terminal, the resolution of images output to the external device varies.

When [OUTPUT BITS] is set to [4:2:2(8bit)]/In Playback Mode When [RESOLUTION] is set to [SYSTEM], the resolution of images output to the external device

varies depending on the picture size and frame rate in [REC FORMAT].

(When [SYSTEM FREQ] is set to [59.94Hz])

Resolution of images output to the external device

Setting Resolution of images output to the external device Picture size/Frame rate

in [REC FORMAT] [RESOLUTION]

setting HDMI OUT terminal SDI OUT terminal VIDEO OUT

terminal

4K (4096k2160)/24.00p [SYSTEM] 2160/24.00p 1080/24.00PsF

[1080p] 1080/24.00p 1080/24.00PsF

UHD (3840k2160)/ 59.94p

[SYSTEM] 2160/59.94p*1 1080/59.94p

[1080p] 1080/59.94p [1080i] 1080/59.94i

[DOWN CONV.] 480/59.94p 480/59.94i

UHD (3840k2160)/ 29.97p

[SYSTEM] 2160/29.97p 1080/29.97PsF

[1080p] 1080/59.94p [1080i] 1080/59.94i

[DOWN CONV.] 480/59.94p 480/59.94i

UHD (3840k2160)/ 23.98p

[SYSTEM] 2160/23.98p 1080/23.98PsF

[1080p] 1080/59.94p [1080i] 1080/59.94i

[DOWN CONV.] 480/59.94p 480/59.94i

FHD (1920k1080)/ 59.94p,

PS 1080/59.94p

[SYSTEM] 1080/59.94p

[1080p] [1080i] 1080/59.94i

[DOWN CONV.] 480/59.94p 480/59.94i

- 116 -

*1 For this resolution (2160/59.94p), an [OUTPUT BITS] setting of 4:2:0 (8bit) will be set. When you record motion picture with this unit, a resolution of 1080/59.94p with an [OUTPUT BITS] setting of 4:2:2 (8bit) will be set.

(When [SYSTEM FREQ] is set to [50.00Hz])

FHD (1920k1080)/ 59.94i,

PH 1080/59.94i, HA 1080/59.94i, HE 1080/59.94i

[SYSTEM] 1080/59.94i

[1080p] 1080/59.94p [1080i] 1080/59.94i

[DOWN CONV.] 480/59.94p 480/59.94i

FHD (1920k1080)/ 29.97p

[SYSTEM] 1080/29.97p 1080/29.97PsF

[1080p] 1080/59.94p [1080i] 1080/59.94i

[DOWN CONV.] 480/59.94p 480/59.94i

Setting Resolution of images output to the external device Picture size/Frame rate

in [REC FORMAT] [RESOLUTION]

setting HDMI OUT terminal SDI OUT terminal VIDEO OUT

terminal

FHD (1920k1080)/ 23.98p,

PH 1080/23.98p

[SYSTEM] 1080/23.98p 1080/23.98PsF

[1080p] 1080/59.94p [1080i] 1080/59.94i

[DOWN CONV.] 480/59.94p 480/59.94i

PM 720 (1280k720)/ 59.94p

[SYSTEM] 720/59.94p

[1080p] 1080/59.94p [1080i] 1080/59.94i

[DOWN CONV.] 480/59.94p 480/59.94i SA 480 (750k480)/

59.94i [SYSTEM] 480/59.94p 480/59.94i

In Playback Mode (still picture)

[SYSTEM] 1080/59.94p

[1080p] [1080i] 1080/59.94i

[DOWN CONV.] 480/59.94p 480/59.94i

Setting Resolution of images output to the external device Picture size/Frame rate

in [REC FORMAT] [RESOLUTION]

setting HDMI OUT terminal SDI OUT terminal VIDEO OUT

terminal

4K (4096k2160)/24.00p [SYSTEM] 2160/24.00p 1080/24.00PsF

[1080p] 1080/24.00p 1080/24.00PsF

UHD (3840k2160)/ 50.00p

[SYSTEM] 2160/50.00p*2 1080/50.00p

[1080p] 1080/50.00p [1080i] 1080/50.00i

[DOWN CONV.] 576/50.00p 576/50.00i

Setting Resolution of images output to the external device Picture size/Frame rate

in [REC FORMAT] [RESOLUTION]

setting HDMI OUT terminal SDI OUT terminal VIDEO OUT

terminal

- 117 -

*2 For this resolution (2160/50.00p), an [OUTPUT BITS] setting of 4:2:0 (8bit) will be set. When you record motion picture with this unit, a resolution of 1080/50.00p with an [OUTPUT BITS] setting of 4:2:2 (8bit) will be set.

If you enable Variable Frame Rate Mode when [RESOLUTION] is set to [SYSTEM], the resolution will be set to either 1080/59.94p or 1080/50.00p. (l 91)

UHD (3840k2160)/ 25.00p

[SYSTEM] 2160/25.00p 1080/25.00PsF

[1080p] 1080/50.00p [1080i] 1080/50.00i

[DOWN CONV.] 576/50.00p 576/50.00i

FHD (1920k1080)/ 50.00p,

PS 1080/50.00p

[SYSTEM] 1080/50.00p

[1080p] [1080i] 1080/50.00i

[DOWN CONV.] 576/50.00p 576/50.00i FHD (1920k1080)/

50.00i, PH 1080/50.00i, HA 1080/50.00i, HE 1080/50.00i

[SYSTEM] 1080/50.00i

[1080p] 1080/50.00p [1080i] 1080/50.00i

[DOWN CONV.] 576/50.00p 576/50.00i

Setting Resolution of images output to the external device Picture size/Frame rate

in [REC FORMAT] [RESOLUTION]

setting HDMI OUT terminal SDI OUT terminal VIDEO OUT

terminal

FHD (1920k1080)/ 25.00p

[SYSTEM] 1080/25.00p 1080/25.00PsF [1080p] 1080/50.00p

[1080i] 1080/50.00i [DOWN CONV.] 576/50.00p 576/50.00i

PM 720 (1280k720)/ 50.00p

[SYSTEM] 720/50.00p [1080p] 1080/50.00p

[1080i] 1080/50.00i [DOWN CONV.] 576/50.00p 576/50.00i

SA 576 (750k576)/ 50.00i [SYSTEM] 576/50.00p 576/50.00i

In Playback Mode (still picture)

[SYSTEM] 1080/50.00p

[1080p] [1080i] 1080/50.00i

[DOWN CONV.] 576/50.00p 576/50.00i

Setting Resolution of images output to the external device Picture size/Frame rate

in [REC FORMAT] [RESOLUTION]

setting HDMI OUT terminal SDI OUT terminal VIDEO OUT

terminal

- 118 -

When [OUTPUT BITS] is set to [4:2:2(10bit)] When [RESOLUTION] is set to [SYSTEM], the resolution of images output to the external device

varies depending on the picture size and frame rate in [OUTPUT FORMAT].

(When [SYSTEM FREQ] is set to [59.94Hz])

(When [SYSTEM FREQ] is set to [50.00Hz])

Setting Resolution of images output to the external device

Picture size/Frame rate in [OUTPUT FORMAT]

[RESOLUTION] setting HDMI OUT terminal SDI OUT terminal

4K (4096k2160)/24.00p [SYSTEM] 2160/24.00p 1080/24.00PsF

[1080p] 1080/24.00p 1080/24.00PsF

UHD (3840k2160)/29.97p [SYSTEM] 2160/29.97p 1080/29.97PsF

[1080p] 1080/59.94p [1080i] 1080/59.94i

UHD (3840k2160)/23.98p [SYSTEM] 2160/23.98p 1080/23.98PsF

[1080p] 1080/59.94p [1080i] 1080/59.94i

FHD (1920k1080)/59.94p [SYSTEM]

1080/59.94p [1080p] [1080i] 1080/59.94i

FHD (1920k1080)/59.94i [SYSTEM] 1080/59.94i

[1080p] 1080/59.94p [1080i] 1080/59.94i

FHD (1920k1080)/29.97p [SYSTEM] 1080/29.97p 1080/29.97PsF

[1080p] 1080/59.94p [1080i] 1080/59.94i

FHD (1920k1080)/23.98p [SYSTEM] 1080/23.98p 1080/23.98PsF

[1080p] 1080/59.94p [1080i] 1080/59.94i

Setting Resolution of images output to the external device

Picture size/Frame rate in [OUTPUT FORMAT]

[RESOLUTION] setting HDMI OUT terminal SDI OUT terminal

4K (4096k2160)/24.00p [SYSTEM] 2160/24.00p 1080/24.00PsF

[1080p] 1080/24.00p 1080/24.00PsF

UHD (3840k2160)/25.00p [SYSTEM] 2160/25.00p 1080/25.00PsF

[1080p] 1080/50.00p [1080i] 1080/50.00i

- 119 -

FHD (1920k1080)/50.00p [SYSTEM]

1080/50.00p [1080p] [1080i] 1080/50.00i

FHD (1920k1080)/50.00i [SYSTEM] 1080/50.00i

[1080p] 1080/50.00p [1080i] 1080/50.00i

FHD (1920k1080)/25.00p [SYSTEM] 1080/25.00p 1080/25.00PsF

[1080p] 1080/50.00p [1080i] 1080/50.00i

Setting Resolution of images output to the external device

Picture size/Frame rate in [OUTPUT FORMAT]

[RESOLUTION] setting HDMI OUT terminal SDI OUT terminal

- 120 -

When this device and a computer for editing are connected using a USB 3.0 Cable (commercially- available), image data in the SD card can be transferred. This unit supports USB 3.0. Concerning non-linear editing, refer to the instruction manual of your editing software. It is impossible to write data to the SD card on this unit from a PC.

Operating environment (mass storage) Even if the system requirements mentioned in these operating instructions are fulfilled, some PCs

cannot be used. The USB equipment operates with the driver installed as standard in the OS.

If using Windows Operation is not guaranteed in the following cases.

j Operation on an upgraded OS. j Operation on an OS other than the one pre-installed.

If using Mac

Linking to external devices

Connecting to a PC (File transfer/nonlinear editing)

OS Windows 10 (32 bit/64 bit) Windows 8/Windows 8.1 (32 bit/64 bit) Windows 7 (32 bit/64 bit) SP1

CPU 1 GHz or higher 32-bit (k86) or 64-bit (k64) processor

RAM 2 GB or more (64 bit)/1 GB or more (32 bit)

Interface USB port

Other requirements Mouse or equivalent pointing device

PC Mac

OS OS X v10.10

CPU Intel Core 2 Duo or better

RAM 2 GB or more

Interface USB port

Other requirements Mouse or equivalent pointing device

- 121 -

Connecting to a PC

A USB 3.0 Cable (commercially-available) Insert the plugs as far as they will go.

1 Connect this unit to the AC adaptor. Use the AC adaptor to free you from worrying about the battery running down.

2 Turn on the unit. 3 Press the THUMBNAIL button to switch this unit to the Playback Mode. 4 Set [USB MODE SELECT] to [DEVICE].

5 Connect this unit to a PC. The USB function selection screen will appear.

6 Touch [PC] on the screen of this unit. This unit is automatically recognized as an external drive of the PC. (l 123) When you select an option other than [PC], reconnect the USB Cable. When using the battery, the LCD monitor turns off after about 5 seconds. Touch the screen to turn

the LCD monitor on.

A USB 3.0 cable is not supplied with this unit. Use a commercially-available double-shielded USB 3.0 cable with a ferrite core. If possible, we recommend using a cable with a length of 1.5 m (4.9 feet) or less.

When performing reading/writing between a PC and an SD card, be aware that some SD card slots built into PCs and some SD card readers are not compatible with the SDHC Memory Card or SDXC Memory Card.

If you are using an SDXC Memory Card, some PC may not recognize the data. Make sure your PC supports SDXC cards.

: [OTHER FUNCTION] # [USB MODE SELECT] # [DEVICE]

DEVICE

USB

MENU

- 122 -

To disconnect USB Cable safely (For Windows) Select the icon in task tray displayed on the PC, and then click the on-screen display that lets you eject [AG-DVX200]. Depending on your PCs settings, this icon may not be displayed. (For Mac) Drag [CAM_SD] disk icon to the [Trash], and then disconnect the USB Cable.

About the PC display When the unit is connected to a PC, it is recognized as an external drive. Removable disk (Example: ) is displayed in [Computer].

Example folder structure of a SD card: The following data will be recorded. 1 Up to 999 still pictures in JPEG format

([01000001.JPG] etc.) 2 MOV format motion picture data

([01000001.MOV], etc.) 3 MP4 format motion picture data

([01000001.MP4], etc.) 4 JPEG format still pictures created from

the motion picture 5 The motion picture thumbnails 6 AVCHD format motion picture files

([00000.MTS] etc.) 7 For management

About the screen indication of the unit Do not disconnect the USB Cable, battery, or AC adaptor while the access lamp is on or card

access icon ( ) appears on the unit screen. If the screen does not change when the unit is operated while connected to a PC, disconnect

the battery and/or AC adaptor, wait approximately 1 minute, reconnect the battery and/or AC adaptor, wait approximately 1 minute again, and then turn the unit back on. (Data may be destroyed when above operation is performed while accessing the SD card.)

Data recorded using AVCHD format has excellent compatibility with computers, due to its file form; however, it contains not just image and sound data, but also various important information, and it is associated using a folder structure which is like a figure. If even part of this information is changed or erased, faults may occur; for example, it may not be possible for the data to be recognized as AVCHD data, or it may no longer be possible for the SD card to be used in an AVCHD device. Data from a computer cannot be written to the SD card of this device.

DCIM

CAM_SD

100CDPFQ

101YAQH0

AVCHDTN

BDMV

AVCHD

PRIVATE

PANA_EXT

102RARH0

103CDPFS

- 123 -

Folder names for motion picture data recorded in MOV/MP4 format The fourth to eighth characters of the folder name of a recorded MOV/MP4 scene are determined by its picture size, frame rate, motion picture format, recording setting and camera number setting.

(Example) If the folder name is 100RARH0: Motion picture data that has a picture size of 3840k2160, frame rate of 59.94 fps, and motion picture format categorized as progressive recording (MP4 and LPCM) is stored.

Do not delete the SD cards folders on a PC. Doing so may make the SD card unusable in this unit.

When data not supported by this unit has been recorded on a PC, it will not be recognized by this unit.

Always use this unit to format SD cards.

Picture size Frame rate Motion picture format Recording setting

Y: 1920k1080 R: 3840k2160 Q: 4096k2160

A: 59.94 fps B: 50 fps C: 29.97 fps D: 25 fps E: 24 fps F: 23.98 fps

J: Interlace recording (MOV, LPCM)

K: Interlace recording (MP4, LPCM)

Q: Progressive recording (MOV, LPCM)

R: Progressive recording (MP4, LPCM)

H: Recordings other than the ones below

D: Sub recordings of dual codec recording (50 Mbps)

E: Sub recordings of dual codec recording (8 Mbps)

P: Main recordings of dual codec recording

A Camera number setting (l 148) B Recording setting C Motion picture format D Frame rate E Picture size

1 0 0 R A R H 0

- 124 -

In these Operating Instructions, USB hard disk drive is indicated as USB HDD. If you connect an external media device, such as USB HDD or USB flash memory (commercially- available) to this unit, you can copy motion pictures and still pictures recorded on this unit to an external media device. It can also play back the scenes and still pictures copied to the external media device. This unit supports USB 3.0. You can copy scenes and still pictures recorded with this unit while maintaining the image quality. Please read the operating instructions of the external media device for how to use it.

Preparing for copying/playing back

In the following cases, an external media device cannot be used by connecting it to this unit: j An external media device with a capacity below 32 GB or above 2 TB j When an external media device has two or more partitions j If an external media device is in a format other than FAT32 or exFAT j When connected by using a USB hub

You cannot copy scenes recorded on an SDXC Memory Card to an external media device in FAT32 format.

A Connect this unit to the external device with USB Cable (supplied with the external media device)

B External media device (commercially-available) C USB flash memory (commercially-available)

1 (When using USB HDD) Connect the AC adaptor (supplied with USB HDD) to the USB HDD.

Linking to external devices

Copying/playing back with an external media device

Refer to the following support site for information about an external media device. http://pro-av.panasonic.net/ (This Site is English only)

When the external media device that requires formatting is connected, a message is displayed. Follow the instructions on the screen to format it. Once the external media device has been formatted, all data stored on it will be deleted. The data cannot be recovered. This unit formats the external media device in exFAT.

USB

HOST

- 125 -

If you are using a bus-powered or portable USB HDD, this unit can supply power to the USB HDD by USB Cable (supplied with USB HDD).

2 Connect the AC adaptor to this unit. Use the AC adaptor to free you from worrying about the battery running down.

3 Turn on this unit, and press the THUMBNAIL button to switch to Playback Mode.

4 Set [USB MODE SELECT] to [HOST].

5 Connect the external media device to the USB HOST terminal of this unit. If you use a USB HDD, connect to the USB HDD with the USB Cable supplied with the USB HDD. It may take several minutes until the connection is completed.

6 Touch the desired item.

Points to check before copying When using an external media device for the first time, or using an external media device

that has been used with other devices, first run [FORMAT MEDIA]. Before copying, go to [MEDIA STATUS] to check the amount of free space on the external media

device. (l 127) It may take longer to copy when there are many scenes. If you copy protected scenes or still pictures, the protection setting of the copied scenes or still

pictures are canceled. The order in which the scenes were copied cannot be changed.

: [OTHER FUNCTION] # [USB MODE SELECT] # [HOST]

[DIFFERENTIAL COPY]: Copies all scenes and still pictures recorded with this unit that have not been copied yet. (l 127)

[SELECT COPY]: Allows you to select desired scenes/still pictures, and then copy. (l 128)

[Playback from External Media]: Plays back scenes and still pictures stored in an external media device on this unit. (l 129)

[Safe Removal]: Allows you to safely remove this unit and an external media device.

When the external media device is connected to other devices such as Blu-ray disc recorder, a message prompting to format the external media device may display. All the scenes and still pictures recorded on the external media device will be erased if formatted. Do not format as important data will get erased and it will be impossible to restore.

Before you delete the data on the SD card after copying is complete, be sure to play back the external media device to check that they have been copied to correctly. (l 129)

MENU

- 126 -

Formatting This is for initializing the external media device. Please be aware that if a media is formatted then all the data recorded on the media is

erased and cannot be recovered. Back up important data on a PC etc. Connect this unit to the external media device and touch [Playback from External Media]. Select the menu.

When formatting is complete, touch [EXIT] to exit the message screen. Connect this unit and the external media device to format.

You may no longer be able to use the external media device if you format them on another device such as a PC etc.

This unit formats the external media device in exFAT.

Displaying media information The used space of the external media device can be checked. Connect this unit to the external media device and touch [Playback from External Media]. Select the menu.

If you touch [CHANGE MEDIA], you can switch the display between the SD card 1, SD card 2, and the external media device.

Differential copy 1 Connect this unit to the external media device to prepare for copying. (l 125) 2 Touch [DIFFERENTIAL COPY]. You can also access this function by selecting menu items.

[COPY] # [DIFFERENTIAL COPY]

3 Touch the media you want to copy. 4 Touch [YES]. 5 Touch [EXIT] when the copy complete message is displayed. The thumbnail view of the copy destination is indicated.

When you stop copying halfway: Touch [CANCEL] while copying.

: [OTHER FUNCTION] # [FORMAT MEDIA] # [EXTERNAL]

: [OTHER FUNCTION] # [MEDIA STATUS]

MENU

MENU

- 127 -

Copy selected files 1 Connect this unit to the external media device to prepare for copying. (l 125) 2 Touch [SELECT COPY]. You can also access this function by selecting menu items.

[COPY] # [SELECT COPY]

3 Touch the media you want to copy.

For information on copying between SD cards, refer to page 111.

4 Touch the desired items following the instructions on the screen. It will return to the previous step by touching [Return]. (When [SELECT SCENES] is selected)

When touched, the scene/still picture is selected and the indication appears on the thumbnail. Touch the scene/still picture again to cancel the operation.

(When [SELECT DATE] is selected) When touched, the date is selected and surrounded by red. Touch the date again to cancel the operation.

Up to 99 scenes/ 99 dates can be selected continuously.

5 Touch [EXIT] when the copy complete message is displayed. The thumbnail view of the copy destination is indicated.

When you stop copying halfway: Touch [CANCEL] while copying.

[ ]: When copying from the SD card 1 to the external media device.

[ ]: When copying from the SD card 2 to the external media device.

- 128 -

Playing back the External Media Only motion picture/still picture that have been copied by connecting this unit to the

external media device can be played back.

A USB Cable (supplied with USB HDD) B USB HDD (commercially-available) C USB flash memory (commercially-available)

1 Connect this unit to the external media device to prepare for playback. (l 125)

When playing back on an external monitor, connect this unit to the external monitor. (l 114)

2 Touch [Playback from External Media]. 3 Touch the scene or still picture to be played back and then play it back. The playback operation is performed the same as when playing back motion pictures or still

pictures. (l 101, 105)

To terminate the connection between this unit and the external media device Touch the play mode select icon (l 101) and then touch .

Disconnect the USB Cable from this unit.

It is also possible to switch the media to play back by touching the play mode select icon. When the external media device is connected, the (external media device) can be selected from the displayed media types. (l 101)

In the following cases, when you have touched a play mode select icon and selected the recording format for playback, this unit will be restarted to change the system frequency. After the restart, perform Step 2. j When you have switched recording format from [4K/24.00p] to a different option. j When you have switched recording format from an option other than [4K/24.00p] to [4K/24.00p]

Deleting scenes and still pictures on the external media device may take time. You cannot set the [SCENE PROTECT] during playback of (external media device). (l 110)

USB

HOST

- 129 -

Refer to page 30 for how to set up the Menu.

Scene file

Settings that are assigned to [SCENE1] in [CUSTOMIZE SCENE] by default are indicated with underlined text.

You can save the desired image settings to each scene number. Switch the scene number in accordance with the recording conditions. 1 Touch [CUSTOMIZE SCENE]. 2 Touch the scene number. The scene number will switch by touching [SCENE1] to [SCENE6]. Touch [EXIT] to exit the menu screen. 3 (To change the image settings)

Change the setting of [SCENE FILE] menu. You can save the settings of the following menu items to the scene number you have selected.

(l 132 to 140) j [SYNCHRO SCAN] j [MASTER DETAIL] j [DETAIL CORING] j [SKIN TONE DTL] j [V DETAIL LEVEL] j [KNEE APE LEVEL] j [RB GAIN CONTROL SETTING] j [CHROMA LEVEL] j [CHROMA PHASE] j [MATRIX] j [COLOR CORRECTION SETTING]

j [MASTER PED] j [GAMMA MODE] j [BLACK GAMMA] j [BLACK GAMMA RANGE] j [KNEE MODE] j [KNEE MASTER POINT] j [KNEE MASTER SLOPE] j [DRS] j [DRS EFFECT] j [AUTO IRIS LEVEL] j [AUTO IRIS LEVEL EFFECT] j [V-Log L MODE]

Menu

Using the Menu

: [SCENE FILE] # desired setting

[CUSTOMIZE SCENE]

[SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]/[SCENE6]

MENU

- 130 -

Default scene number settings

This functions default setting is [SCENE1]. It is possible to switch the scene file by touching to while displaying the operation icons.

(l 97) It will return to the default settings when [SCENE] is selected in [INITIAL SET]. (l 178)

You can save the scene file settings of [CUSTOMIZE SCENE] to the SD card or load them from the SD card to this unit. (l 89)

This enables/disables Variable Frame Rate Mode. In Variable Frame Rate Mode, you can record quick or slow motion picture by changing the frame rate before recording. For information on how to use Variable Frame Rate Mode, refer to page 91.

This functions default setting is [OFF].

You can adjust the frame rate for Variable Frame Rate Mode. Set [VFR MODE] to [ON]. (l 91, above) 1 Touch [FRAME RATE]. 2 Touch / to adjust the frame rate. You can select a value between 2fps and 120fps. 3 Touch [EXIT] to complete the setting.

When the default setting for [SYSTEM FREQ] is [59.94Hz]: This functions default setting is 60fps. When the default setting for [SYSTEM FREQ] is [50.00Hz]: This functions default setting is 50fps.

When [REC MODE] and [REC FORMAT] are set to settings that are not available for Variable Frame Rate Mode, [FRAME RATE] cannot be set. (l 91)

If you set the frame rate to 100fps or 120fps, the angle of view will change. (The color of the frame rate value will change to blue.)

[SCENE1] Setting appropriate for standard recording [SCENE2] Setting appropriate for recording considering the characteristic of fluorescent lamps

(indoors, etc.) [SCENE3] Setting appropriate for recording with modulation in resolution, color shade, and contrast [SCENE4] Setting appropriate for recording with wider gradation in dark area (dusk, etc.) [SCENE5] Setting appropriate for recording as a cinema with high contrast [SCENE6] Setting appropriate for recording as a cinema with high dynamic range

[SCENE FILE]

[LOAD]/[SAVE]

[VFR MODE]

[ON]/[OFF]

[FRAME RATE]

SCN1 SCN6

- 131 -

Sets the initial Synchro Scan setting. The setting range changes depending on the size and frame rate in [REC FORMAT] or [OUTPUT

FORMAT]. (l 142, 147)

1 Touch [SYNCHRO SCAN]. 2 Touch / to adjust settings. 3 Touch [EXIT] to complete the setting. Note on the [SYNCHRO SCAN] setting A separate [SYNCHRO SCAN] setting is maintained for each size and frame rate of [REC FORMAT] or [REC FORMAT].

Default settings are indicated with underlined text.

When the default setting for [SYSTEM FREQ] is [59.94Hz]: This functions default setting is 1/60.0. When the default setting for [SYSTEM FREQ] is [50.00Hz]: This functions default setting is 1/50.0.

Adjusts the degree of overall outline correction in images. 1 Touch [MASTER DETAIL]. 2 Touch / to adjust settings. You can select a value between s31 and r31. 3 Touch [EXIT] to exit the menu screen.

The default setting that is assigned to [SCENE1] in [CUSTOMIZE SCENE] is 0.

[SYNCHRO SCAN]

Frame rates [SYNCHRO SCAN] setting

59.94p/59.94i

(When the size for [REC FORMAT] or [OUTPUT FORMAT] is UHD (3840k2160))

1/60.0 to 1/249.7

(When the picture size for [REC FORMAT] or [OUTPUT FORMAT] is 1920k1080 or below)

1/60.0 to 1/249.8

29.97p 1/30.0 to 1/60.0 to 1/249.8

23.98p 1/24.0 to 1/48.0 to 1/249.6

24.00p

50.00p/50.00i 1/50.0 to 1/250.0

25.00p 1/25.0 to 1/50.0 to 1/250.0

[MASTER DETAIL]

- 132 -

Adjusts the detail noise removal level. 1 Touch [DETAIL CORING]. 2 Touch / to adjust settings. You can select a value between 0 and 60. 3 Touch [EXIT] to exit the menu screen.

The default setting that is assigned to [SCENE1] in [CUSTOMIZE SCENE] is 1.

This makes skin colors appear softer for a more attractive appearance. This is more effective if you record a person closely from the torso up. 1 Touch [SKIN TONE DTL]. 2 Touch [ON]. 3 Touch [EXIT] to exit the menu screen.

If the background or anything else in the scene has colors similar to the skin color, they will also be smoothed.

If the brightness is insufficient, the effect may not be clear. If you record a person in the distance, the face may not be recorded clearly. In this case, set

[SKIN TONE DTL] to [OFF] or zoom in on the face (close-up) to record.

Adjusts the degree of vertical outline correction in images. 1 Touch [V DETAIL LEVEL]. 2 Touch / to adjust settings. You can select a value between s7 and r7. 3 Touch [EXIT] to exit the menu screen.

The default setting that is assigned to [SCENE1] in [CUSTOMIZE SCENE] is 0.

[DETAIL CORING]

[SKIN TONE DTL]

[ON]/[OFF]

[V DETAIL LEVEL]

- 133 -

This sets the detail level of high luminosity areas (extremely bright areas). 1 Touch [KNEE APE LEVEL]. 2 Touch the desired setting item.

3 Touch [EXIT] to exit the menu screen.

This adjusts the color balance for each position of the WHITE BAL switch. You can also set whether or not to apply the color balance settings to Auto White Balance/Auto Black Balance. These settings do not work when the White Balance mode is set to [ATW].

1 Touch [RB GAIN CONTROL SETTING], and select the desired item.

2 Touch the desired setting item.

* Displayed only if you touch [AWB A] or [AWB B] in Step 1. 3 (If you have touched [R GAIN]/[B GAIN] in Step 2)

Touch / to adjust the color balance. You can select a value between s30 and r30. Touch [RETURN].

(If you have touched [GAIN OFFSET] in Step 2) Touch [ON] or [OFF].

To make additional changes, repeat Steps 2s3. 4 Touch [EXIT] to exit the menu screen.

The default settings that are assigned to [SCENE1] in [CUSTOMIZE SCENE] are as follows: j [R GAIN]: 0 j [B GAIN]: 0 j [GAIN OFFSET]: [OFF]

[KNEE APE LEVEL]

[0]/[1]/[2]/[3]/[4]/[5]

[RB GAIN CONTROL SETTING]

[AWB PRE]: Setting for the PRST position of the WHITE BAL switch

[AWB A]: Setting for the A position of the WHITE BAL switch

[AWB B]: Setting for the B position of the WHITE BAL switch

[R GAIN]: Adjusts the intensity of red.

[B GAIN]: Adjusts the intensity of blue.

[GAIN OFFSET]*: Sets whether to maintain or reset the [R GAIN] and [B GAIN] settings when Auto White Balance/Auto Black Balance is used.

[ON]: Maintains the [R GAIN] and [B GAIN] settings when Auto White Balance/Auto Black Balance is used.

[OFF]: Resets the [R GAIN] and [B GAIN] settings when Auto White Balance/Auto Black Balance is used.

- 134 -

Adjusts color density. 1 Touch [CHROMA LEVEL]. 2 Touch / to adjust settings. You can select a value between s70 and r30. 3 Touch [EXIT] to exit the menu screen.

The default setting that is assigned to [SCENE1] in [CUSTOMIZE SCENE] is 0.

Adjusts color balance. 1 Touch [CHROMA PHASE]. 2 Touch / to adjust settings. You can select a value between s31 and r31. 3 Touch [EXIT] to exit the menu screen.

The default setting that is assigned to [SCENE1] in [CUSTOMIZE SCENE] is 0.

Represents the color during the recording. 1 Touch [MATRIX]. 2 Touch the desired setting item.

3 Touch [EXIT] to exit the menu screen.

[CHROMA LEVEL]

[CHROMA PHASE]

[MATRIX]

[NORM1]: Suitable for recording in the open air or under a halogen lamp.

[NORM2]: Suitable for brighter colors than the [NORM1] mode.

[FLUO]: Suitable for recording indoors under fluorescent lamp.

[CINE-LIKE]: Suitable for cinema-like image.

- 135 -

This function sets color saturation and phase. It applies individual effect on 16 phases in an image. It can be set to individual color hue.

1 Touch [COLOR CORRECTION SETTING]. 2 Touch the phase you want to set.

Next (Previous) page can be displayed by touching / . 3 (To adjust the saturation)

Touch [SAT]. (To adjust the phase) Touch [PHASE].

4 Touch / to adjust settings. You can select a value between s63 and r63. (If you have touched [PHASE])

Making adjustments in the + direction corresponds to making adjustments clockwise in the diagram above. Conversely, making adjustments in the j direction corresponds to making adjustments counterclockwise in the diagram.

5 Touch [RETURN]. Touch [EXIT] to exit the menu screen.

[COLOR CORRECTION SETTING]

[R]/[R-Mg]/[Mg]/[Mg-Mg-B]/[Mg-B-B]/[B]/[B-B-Cy]/ [B-Cy-Cy]/[Cy]/[Cy-G]/[G]/[G-G-Yl]/[G-Yl-Yl]/[Yl]/ [Yl-Yl-R]/[Yl-R-R]

90

180

270

0

22.5

45

67.5112.5

135

157.5

202.5

225

247.5 292.5

315

337.5

B

Mg-B-B

Mg-Mg-B

Mg

R-Mg

R

YI-R-R

YI-YI-R

Yl

G-YI-YI

G-G-YI

G

Cy-G

Cy

B-Cy-Cy

B-B-Cy

A [PHASE] adjustment B [SAT] adjustment

- 136 -

Adjustment of black level based on the image is performed. 1 Touch [MASTER PED]. 2 Touch / to adjust the black level. You can select a value between s150 and r150. 3 Touch [EXIT] to exit the menu screen.

The default setting that is assigned to [SCENE1] in [CUSTOMIZE SCENE] is 0.

Tone or contrast of the image is set in accordance with the recorded scenes. 1 Touch [GAMMA MODE]. 2 Touch the desired setting item.

3 Touch [EXIT] to exit the menu screen.

When [CINE-LIKE V] or [CINE-LIKE D] is selected, we recommend that you set the lens aperture to a level lower than the normal lens iris level (approximately 1/2) to fully utilize the feature of the selected setting.

[MASTER PED]

[GAMMA MODE]

[HD]: This is the video gamma feature for HD (High Definition).

[SD]: This increases gain in darker areas more than [HD] does.

[FILMLIKE1]: This feature reproduces highlight areas more than [HD] does.

[FILMLIKE2]: This feature reproduces highlight areas more than [FILMLIKE1] does.

[FILMLIKE3]: This feature reproduces highlight areas more than [FILMLIKE2] does.

[CINE-LIKE V]: This gamma feature creates cinematic images with sharper contrast.

[CINE-LIKE D]: This gamma feature creates cinematic images.

- 137 -

This sets the gamma curve of dark areas. 1 Touch [BLACK GAMMA]. 2 Touch / to adjust settings. You can select a value between s8 and r8. Making adjustments in the direction compresses dark areas, while making adjustments in the +

direction expands them. 3 Touch [EXIT] to complete the setting.

The default setting that is assigned to [SCENE1] in [CUSTOMIZE SCENE] is 0.

This sets the upper limit on the compression/expansion of the [BLACK GAMMA] setting. 1 Touch [BLACK GAMMA RANGE]. 2 Touch the desired setting item.

3 Touch [EXIT] to exit the menu screen.

To avoid overexposure, select the compression level of the high intensity video signals received through the image sensor. 1 Touch [KNEE MODE]. 2 Touch the desired setting item.

3 Touch [EXIT] to exit the menu screen.

This adjusts the knee point position in 0.5% steps when [KNEE MODE] is set to [MANUAL]. 1 Touch [KNEE MASTER POINT]. 2 Touch / to adjust settings. You can select a value between 80.0 and 107.0. 3 Touch [EXIT] to exit the menu screen.

The default setting that is assigned to [SCENE1] in [CUSTOMIZE SCENE] is 93.0.

[BLACK GAMMA]

[BLACK GAMMA RANGE]

[1] (approx. 20%)/[2] (approx. 30%)/[3] (approx. 40%)

[KNEE MODE]

[AUTO]: Sets the level automatically according to the signals received.

[MANUAL]: Applies the [KNEE MASTER POINT] and [KNEE MASTER SLOPE] settings.

[OFF]: Disables the Knee function.

[KNEE MASTER POINT]

- 138 -

This sets the knee inclination when [KNEE MODE] is set to [MANUAL]. 1 Touch [KNEE MASTER SLOPE]. 2 Touch / to adjust settings. You can select a value between 0 and 99. 3 Touch [EXIT] to exit the menu screen.

The default setting that is assigned to [SCENE1] in [CUSTOMIZE SCENE] is 85.

Selects the DRS (Dynamic Range Stretcher) function. (l 81)

Selects the level of the DRS function. 1 Touch [DRS EFFECT]. 2 Touch the desired setting item.

Higher the value, greater the compression level of the highly illuminated area. Higher the value, greater the noise of the dark area. 3 Touch [EXIT] to exit the menu screen.

This enables/disables Auto Iris Level. (l 60)

Adjusting brightness during the Auto Iris Mode. (l 60)

The default setting that is assigned to [SCENE1] in [CUSTOMIZE SCENE] is 0.

[KNEE MASTER SLOPE]

[DRS]

[ON]/[OFF]

[DRS EFFECT]

[1]/[2]/[3]

[AUTO IRIS LEVEL]

[ON]/[OFF]

[AUTO IRIS LEVEL EFFECT]

- 139 -

When this item is set to [ON], V-Log L (12 stops) allows you to record expressive images with greater latitude. Images recorded in this mode are suitable for color grading.

The following menu items are not available when [V-Log L MODE] is set to [ON]: j [SCENE FILE] (l 89, 131) j [MASTER DETAIL] (l 132) j [DETAIL CORING] (l 133) j [SKIN TONE DTL] (l 133) j [V DETAIL LEVEL] (l 133) j [KNEE APE LEVEL] (l 134) j [RB GAIN CONTROL SETTING] (l 134) j [CHROMA LEVEL] (l 135) j [CHROMA PHASE] (l 135) j [MATRIX] (l 135) j [COLOR CORRECTION SETTING]

(l 136)

j [MASTER PED] (l 137) j [GAMMA MODE] (l 137) j [BLACK GAMMA] (l 138) j [BLACK GAMMA RANGE] (l 138) j [KNEE MODE] (l 138) j [KNEE MASTER POINT] (l 138) j [KNEE MASTER SLOPE] (l 139) j [DRS] (l 81, 139) j [DRS EFFECT] (l 139) j [HIGH SENS. MODE] (l 148)

If you set this item to [ON], you can compensate for and reduce flash band, a phenomenon that creates markedly different levels of luminance between the top and bottom of the image when recording is performed in an environment where another camera is firing its flash. (l 86)

This functions default setting is [OFF].

[V-Log L MODE]

[ON]/[OFF]

[FLASH BAND COMPENSATION]

[ON]/[OFF]

- 140 -

System mode

All default settings are indicated with underlined text.

Set the system frequency of this unit.

After you have changed the system frequency, this unit will be restarted automatically.

By default, the system frequency is set to the broadcasting system of the region where this product was purchased. AG-DVX200PJ/PB/PX: This functions default setting is [59.94Hz]. AG-DVX200EJ/EN/ED: This functions default setting is [50.00Hz].

When recording with [REC MODE] set to [AVCHD], you cannot record scenes of different system frequencies into a single SD card. Use a different SD card for each system frequency.

You can change the picture quality of images to be output to an external device according to the recording method used. (l 31)

Switch the recording mode of the motion pictures to record. Set [OUTPUT BITS] to [4:2:2(8bit)].

* It is not compatible with motion pictures recorded in AVCHD.

This function is not available in the following cases: j When [OUTPUT BITS] is set to [4:2:2(10bit)] j In Variable Frame Rate Mode (l 91) j During the Interval Recording (l 162) j During Freeze Frame (l 81)

: [SYSTEM MODE] # desired setting

[SYSTEM FREQ]

[59.94Hz]: System frequency for regions where the TV broadcasting system is NTSC

[50.00Hz]: System frequency for regions where the TV broadcasting system is PAL

[OUTPUT BITS]

[4:2:2(10bit)]/[4:2:2(8bit)]

[REC MODE]

[MOV]*: This recording method is suitable for editing images. Motion pictures will be saved in MOV format.

[MP4]*: This recording method is suitable for editing images. Motion pictures will be saved in MP4 format.

[AVCHD]: This recording method is suitable for playback on a high-definition compatible external monitor.

MENU

- 141 -

Switch the picture quality of motion pictures to be recorded with this unit. Depending on the settings of [SYSTEM FREQ] (l 141) and [REC MODE], the available [REC FORMAT] settings differ.

[REC FORMAT]

How to read a [REC FORMAT] setting Items that make up a [REC FORMAT] setting represent Size, Vertical resolution, Frame rate, and Bit rate. (Excluding the [REC FORMAT] settings that are available when [REC MODE] is set to [AVCHD])

A Size B Vertical resolution

C Frame rate D Bit rate

Smoother motion picture can be recorded with the higher value for the frame rate. [i] and [p] of the frame rate means interlace and progressive respectively.

Interlace (interlacing scanning) Video signal that divides the effective scanning lines to half and send them alternatively Progressive (progressive scanning) High density video signal sending the effective scanning lines simultaneously (It will be higher quality image than the interlace.) The higher the bit rate value is, the higher the picture quality becomes, except for when the

recording format is (This exception is due to a difference in compression method). It can record with highest quality image in this unit when set to [UHD 2160/59.94p 150M] or

[UHD 2160/50.00p 150M]. When the recording format is , recording is performed with ALL-Intra. ALL-Intra is a

compression method that compresses each frame. This method results in larger file sizes, but it can minimize the deterioration in picture quality that occurs during editing.

Depending on the [REC MODE] setting and the bit rate of the [REC FORMAT] setting, its required Speed Class of the SD card differs. Use an SD card that meets the settings. For details, refer to About the Speed Class ratings for recording motion pictures on page 21.

UHD 2160 / 59.94p 150M

- 142 -

Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) When [MOV] or [MP4] in [REC MODE] is selected

When [AVCHD] in [REC MODE] is selected

Recording format System frequency setting

Size (Picture size) Frame rate Bit rate (VBR)

[4K 2160/24.00p 100M] [59.94Hz]/ [50.00Hz]

4K (4096k2160) 24.00p Average 100 Mbps

[UHD 2160/59.94p 150M]

[59.94Hz]

UHD (3840k2160)

59.94p Average 150 Mbps

[UHD 2160/29.97p 100M] 29.97p Average 100 Mbps

[UHD 2160/23.98p 100M] 23.98p

[FHD 1080/59.94p ]

FHD (1920k1080)

59.94p

Average 200 Mbps

[FHD 1080/59.94p 100M] Average 100 Mbps

[FHD 1080/59.94p 50M] Average 50 Mbps

[FHD 1080/29.97p ] 29.97p Average 200 Mbps

[FHD 1080/23.98p ] 23.98p

[FHD 1080/29.97p 50M] 29.97p

Average 50 Mbps[FHD 1080/23.98p 50M] 23.98p

[FHD 1080/59.94i 50M] 59.94i

[UHD 2160/50.00p 150M]

[50.00Hz]

UHD (3840k2160)

50.00p Average 150 Mbps

[UHD 2160/25.00p 100M] 25.00p Average 100 Mbps

[FHD 1080/50.00p ]

FHD (1920k1080)

50.00p

Average 200 Mbps

[FHD 1080/50.00p 100M] Average 100 Mbps

[FHD 1080/50.00p 50M] Average 50 Mbps

[FHD 1080/25.00p ] 25.00p

Average 200 Mbps

[FHD 1080/25.00p 50M] Average 50 Mbps

[FHD 1080/50.00i 50M] 50.00i

Recording format

System frequency setting Picture size Frame rate Bit rate (VBR)

[PS 1080/59.94p]

[59.94Hz]

1920k1080

59.94p Average 25 Mbps

[PH 1080/59.94i] 59.94i Average 21 Mbps

[PH 1080/23.98p] 23.98p

[HA 1080/59.94i] 59.94i

Average 17 Mbps

[HE 1080/59.94i] 1440k1080 Average 5 Mbps

[PM 720/59.94p] 1280k720 59.94p Average 8 Mbps

[SA 480/59.94i] 720k480 59.94i Average 9 Mbps

- 143 -

Recordable time using the battery (l 18) The system frequency is set to 24.00 Hz when [4K 2160/24.00p 100M] is selected. When the default setting for [SYSTEM FREQ] is [59.94Hz]:

The default setting for [REC MODE] is [MP4], and the default setting for [REC FORMAT] is [UHD 2160/59.94p 150M]. When the default setting for [SYSTEM FREQ] is [50.00Hz]: The default setting for [REC MODE] is [MP4], and the default setting for [REC FORMAT] is [UHD 2160/50.00p 150M].

This item cannot be set in the following cases: j When [OUTPUT BITS] is set to [4:2:2(10bit)] j During the Interval Recording (l 162) j During Freeze Frame (l 81)

The following [REC FORMAT] settings are available when [2 SLOTS FUNC.] is set to [BACKGROUND] (l 159): j [FHD 1080/59.94p 50M]/[FHD 1080/29.97p 50M]/[FHD 1080/23.98p 50M]/[FHD 1080/59.94i

50M]/[FHD 1080/50.00p 50M]/[FHD 1080/25.00p 50M]/[FHD 1080/50.00i 50M] The following [REC FORMAT] settings are available in Variable Frame Rate Mode (l 91):

j [FHD 1080/59.94p 50M]/[FHD 1080/29.97p 50M]/[FHD 1080/23.98p 50M]/[FHD 1080/50.00p 50M]/[FHD 1080/25.00p 50M]

Please refer to page 200 about approximate recordable time. When any of the following [REC FORMAT] settings is selected, the angle of view will change.

j [4K 2160/24.00p 100M] j [UHD 2160/59.94p 150M]/[UHD 2160/50.00p 150M] j [REC FORMAT] settings with a size of FHD (1920k1080)

When the unit is moved a lot or moved quickly, or when a fast-moving subject is recorded, mosaic-type noise may appear at playback. (Only when recording AVCHD scenes)

In the following cases, this unit will be restarted to switch the system frequency: j When you have changed [REC FORMAT] from [4K 2160/24.00p 100M] to a different setting. j When you have changed [REC FORMAT] from a setting other than [4K 2160/24.00p 100M] to

[4K 2160/24.00p 100M]

[PS 1080/50.00p]

[50.00Hz]

1920k1080

50.00p Average 25 Mbps

[PH 1080/50.00i]

50.00i

Average 21 Mbps

[HA 1080/50.00i] Average 17 Mbps

[HE 1080/50.00i] 1440k1080 Average 5 Mbps

[PM 720/50.00p] 1280k720 50.00p Average 8 Mbps

[SA 576/50.00i] 720k576 50.00i Average 9 Mbps

Recording format

System frequency setting Picture size Frame rate Bit rate (VBR)

- 144 -

About recording formats and recording functions The relationship between recording formats and recording functions of this unit are shown below. : Available; s: Not available* * Not available includes instances where the desired function cannot be used or selected.

Recording format

Recording function

Normal recording

Interval Rec

(l 162) VFR Mode (l 91, 131)

Relay recording (l 159)

Simultaneous recording (l 160)

Background recording (l 160)

Dual codec recording

(l 160, 161) [4K 2160/

24.00p 100M]

s s s

[UHD 2160/ 59.94p 150M]

s s s s

[UHD 2160/ 50.00p 150M] s s s s

[UHD 2160/ 29.97p 100M] s s

[UHD 2160/ 25.00p 100M] s s

[UHD 2160/ 23.98p 100M] s s s

[FHD 1080/ 59.94p ] s s s

[FHD 1080/ 50.00p ] s s s

[FHD 1080/ 29.97p ] s s s

[FHD 1080/ 25.00p ] s s s

[FHD 1080/ 23.98p ] s s s

[FHD 1080/ 59.94p 100M] s s s

[FHD 1080/ 50.00p 100M] s s s

- 145 -

Recording format

Recording function

Normal recording

Interval Rec

(l 162) VFR Mode (l 91, 131)

Relay recording (l 159)

Simultaneous recording (l 160)

Background recording (l 160)

Dual codec recording

(l 160, 161) [FHD 1080/ 59.94p 50M] s s

[FHD 1080/ 50.00p 50M] s s

[FHD 1080/ 29.97p 50M] s

[FHD 1080/ 25.00p 50M] s

[FHD 1080/ 23.98p 50M] s s

[FHD 1080/ 59.94i 50M] s s s

[FHD 1080/ 50.00i 50M] s s s

[PS 1080/ 59.94p] s s s

[PS 1080/ 50.00p] s s s

[PH 1080/ 59.94i] s s s

[PH 1080/ 50.00i] s s s

[PH 1080/ 23.98p] s s s

[HA 1080/ 59.94i] s s

[HA 1080/ 50.00i] s s

[HE 1080/ 59.94i] s s s

[HE 1080/ 50.00i] s s s

[PM 720/ 59.94p] s s s

[PM 720/ 50.00p] s s s

[SA 480/ 59.94i] s s s

[SA 576/ 50.00i] s s s

- 146 -

This changes the picture quality of images to be output to an external device. The available [OUTPUT FORMAT] vary depending on the [SYSTEM FREQ] (l 141) setting. Set [OUTPUT BITS] to [4:2:2(10bit)]. (l 31)

When the default setting for [SYSTEM FREQ] is [59.94Hz]: This functions default setting is [UHD 2160/29.97p]. When the default setting for [SYSTEM FREQ] is [50.00Hz]: This functions default setting is [UHD 2160/25.00p].

The system frequency is set to 24.00 Hz when [4K 2160/24.00p] is selected. This unit restarts in the following situations to change the system frequency:

j When you have changed [OUTPUT FORMAT] from [4K 2160/24.00p] to another one j When you have changed [OUTPUT FORMAT] from a setting other than [4K 2160/24.00p] to

[4K 2160/24.00p] This item cannot be set in the following cases:

j When [OUTPUT BITS] is set to [4:2:2(8bit)] j During Freeze Frame (l 81)

[OUTPUT FORMAT]

[OUTPUT FORMAT] System frequency setting Size (Picture size) Frame rate

[4K 2160/24.00p] 59.94Hz/ 50.00Hz 4K (4096k2160) 24.00p

[UHD 2160/29.97p]

59.94Hz

UHD (3840k2160) 29.97p

[UHD 2160/23.98p] 23.98p

[FHD 1080/59.94p]

FHD(1920k1080)

59.94p

[FHD 1080/29.97p] 29.97p

[FHD 1080/23.98p] 23.98p

[FHD 1080/59.94i] 59.94i

[UHD 2160/25.00p]

50.00Hz

UHD (3840k2160) 25.00p

[FHD 1080/50.00p]

FHD (1920k1080)

50.00p

[FHD 1080/25.00p] 25.00p

[FHD 1080/50.00i] 50.00i

- 147 -

This sets the aspect ratio of images to be recorded with a [REC FORMAT] setting of [SA 480/59.94i] or [SA 576/50.00i]. Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) Set [REC FORMAT] to [SA 480/59.94i] or [SA 576/50.00i]. (l 142)

This function is not available in the following cases: j When [REC FORMAT] is set to an option other than [SA 480/59.94i] or [SA 576/50.00i] (l 142) j When [OUTPUT BITS] is set to [4:2:2(10bit)] j During Freeze Frame (l 81)

This sets the optimal recording mode for the recording environment.

[H.SENS] is displayed on the screen when [HIGH SENS.] is selected. This function is not available in the following cases:

j In Variable Frame Rate Mode (l 91) j During Freeze Frame (l 81)

This sets the camera number for this unit. 1 Touch [CAMERA NUMBER SET]. 2 Touch / to change the Camera Number. Numbers between 0 and 9 can be set. 3 Touch [RETURN]. Touch [EXIT] to exit the menu screen.

This functions default setting is 0.

[ASPECT CONVERT]

[SIDE CROP]: Records images in standard 4:3 mode. The sides will be cut off.

[LETTERBOX]: Records images in the 16:9 aspect ratio. Black bands at the top and bottom of the picture will be recorded. Since the screen size of the viewfinder and LCD monitor of this unit is 16:9, black bands do not appear at their top and bottom.

[SQUEEZE]: Records images by compressing images in the horizontal direction. When recorded images are played back on a wide-screen external monitor, they appear in the 16:9 aspect ratio.

[HIGH SENS. MODE]

[NORMAL]: Select this setting when the light level of the recording environment is normal.

[HIGH SENS.]: Select this setting when recording in a dark environment.

[CAMERA NUMBER SET]

- 148 -

User switch All default settings are indicated with underlined text.

Sets the function to assign to the USER buttons. (l 74) For the functions of the USER button that can be registered, refer to page 76.

The default settings are as follows:

j USER1: [DRS] j USER2: [ATW] j USER3: [BACKLIGHT] j USER4: [FOCUS MACRO]

j USER5: [O.I.S.] j USER6: [ZEBRA] j USER7: [WFM] j USER8: [REC CHECK]

Register functions to USER button icons. (l 74) For the functions of the USER button that can be registered, refer to page 76.

The default settings are as follows:

j USER9: [FRZ FRAME] j USER10: [EVF/LCD DETAIL]

j USER11: [ATW LOCK] j USER12: [MENU]

Switches the display of the set USER button icons. (l 75)

: [USER SW] # desired setting

[USER1]/[USER2]/[USER3]/[USER4]/ [USER5]/[USER6]/[USER7]/[USER8]

MENU

[USER9]/[USER10]/[USER11]/[USER12]

[USER BUTTON DISPLAY]

[ON]/[OFF]

- 149 -

Switch setting

All default settings are indicated with underlined text.

Sets the rotation direction and iris control of the iris ring.

Sets the gain value for the [L] position of the GAIN switch. 1 Touch [LOW GAIN]. 2 Touch / to adjust settings. When [GAIN/ISO DISPLAY CHG] (l 173) is set to [GAIN], you can select [AUTO] or a value

between 0dB and 24dB. When [GAIN/ISO DISPLAY CHG] is set to [ISO], you can select [AUTO] or a value between

ISO500 and ISO8000. 3 Touch [EXIT] to exit the menu screen.

This functions default setting is 0dB.

Sets the gain value for the [M] position of the GAIN switch. 1 Touch [MID GAIN]. 2 Touch / to adjust settings. When [GAIN/ISO DISPLAY CHG] (l 173) is set to [GAIN], you can select [AUTO] or a value

between 0dB and 24dB. When [GAIN/ISO DISPLAY CHG] is set to [ISO], you can select [AUTO] or a value between

ISO500 and ISO8000. 3 Touch [EXIT] to exit the menu screen.

This functions default setting is 6dB.

: [SW SETUP] # desired setting

[IRIS RING]

[DOWN OPEN]: Iris will open when it is turned toward B.

[UP OPEN]: Iris will open when it is turned toward A.

1 Iris ring

[LOW GAIN]

[MID GAIN]

MENU

A

B

- 150 -

Sets the gain value for the [H] position of the GAIN switch. 1 Touch [HIGH GAIN]. 2 Touch / to adjust settings. When [GAIN/ISO DISPLAY CHG] (l 173) is set to [GAIN], you can select [AUTO] or a value

between 0dB and 24dB. When [GAIN/ISO DISPLAY CHG] is set to [ISO], you can select [AUTO] or a value between

ISO500 and ISO8000. 3 Touch [EXIT] to exit the menu screen.

This functions default setting is 12dB.

Sets the gain value for the USER button function [SUPER GAIN]. (l 62) Switch to Manual Mode. (l 36) (When [GAIN/ISO DISPLAY CHG] (l 173) is set to [GAIN])

(When [GAIN/ISO DISPLAY CHG] is set to [ISO])

This enables/disables the Image Stabilizer. (l 42)

You can set the Hybrid Optical Image Stabilizer. (l 42)

When [ON] is selected, the Image Stabilizer works with customized [BLUR AMPLITUDE] and [BLUR FREQUENCY] settings. (l 43)

[HIGH GAIN]

[SUPER GAIN]

[30 dB]/[36 dB]

[ISO16000]/[ISO32000]

[O.I.S.]

[ON]/[OFF]

[HYBRID O.I.S.]

[ON]/[OFF]

[CUSTOM O.I.S.]

[ON]/[OFF]

- 151 -

This sets the blur amplitude of the Image Stabilizer during recording. (l 43)

This sets the blur frequency of the Image Stabilizer. (l 43)

You can assign ATW to the WHITE BAL switch.

This sets the control speed for ATW. (l 57)

This fine-adjusts the intensity of red. (l 57)

This functions default setting is 0.

This fine-adjusts the intensity of blue. (l 57)

This functions default setting is 0.

[BLUR AMPLITUDE]

[1]/[2]/[3]/[4]/[5]

[BLUR FREQUENCY]

[1]/[2]/[3]

[ATW SET]

[OFF]: Does not assign ATW to the WHITE BAL switch.

[Ach]: Sets the White Balance mode to ATW when the WHITE BAL switch is set to A.

[Bch]: Sets the White Balance mode to ATW when the WHITE BAL switch is set to B.

[PRST]: Sets the White Balance mode to ATW when the WHITE BAL switch is set to PRST.

[ATW SPEED]

[FAST]/[NORMAL]/[SLOW]

[ATW TARGET R]

[ATW TARGET B]

- 152 -

Sets which White Balance mode to use when the WHITE BAL switch is set to the PRST position.

Sets the color temperature when the White Balance mode is set to [VAR]. (l 58) 1 Touch [WB VAR]. 2 Touch / to adjust settings. You can select a value between 2000K and 15000K. 3 Touch [EXIT] to exit the menu screen.

This functions default setting is [3200K].

When [ON] is selected, focus is automatically adjusted after you adjust it with the focus ring in Manual Focus Mode. (l 51)

You can change the focus position setting for the automatic focus adjustment of MF Assist. (l 51)

Sets the Focus Assist method. (l 48)

You can set the peaking color for Focus Assist. (l 49)

[WB PRESET]

[3200K]/[5600K]/[VAR]

[WB VAR]

[MF ASSIST]

[ON]/[OFF]

[MF ASSIST MODE]

[CENTER AREA]/[MULTI AREA]

[FOCUS ASSIST]

[EXPAND]/[PEAKING]/[BOTH]

[PEAKING COLOR]

[Red]/[Blue]/[Yellow]/[White]

- 153 -

You can set the peaking strength for Focus Assist. (l 50)

This functions default setting is 0.

This sets the way you adjust focus with the focus ring. (l 45)

This enables/disables the Focus Macro function. If [ON] is selected, subjects at a distance of approximately 10 cm (3.93 q) to infinity can be

brought into focus when the zoom position is at the W end. (l 40)

This sets the control speed in Auto Iris Mode. (l 60)

You can set an Area Mode effect. (l 82)

When [ON] is selected, Auto Focus works with customized [AF SPEED] and [AF SENSITIVITY] settings. (l 46)

You can adjust the focus speed of Auto Focus. (l 46)

This functions default setting is 0.

[PEAKING LEVEL]

[FOCUS RING DRIVE]

[SPEED]/[COARSE]/[FINE]

[FOCUS MACRO]

[ON]/[OFF]

[A.IRIS SPEED]

[FAST]/[NORMAL]/[SLOW]

[AREA MODE]

[INH]/[FOCUS]/[IRIS]/[Y GET]/[FOCUS/IRIS]/[FOCUS/Y GET]

[CUSTOM AF]

[ON]/[OFF]

[AF SPEED]

- 154 -

You can adjust the tracking sensitivity of Auto Focus. (l 46)

This functions default setting is 5.

You can adjust the effective area width for Auto Focus according to the size of the subject. (l 47)

This enables/disables the Wave Form Monitor function. (l 87)

This sets the type of Wave Form Monitor. (l 87)

This sets the display positions of Wave Form Monitor. (l 87)

* Not displayed when [ZEBRA 2]/[MARKER] is set to [OFF]. (l 171)

Switch between the zebra display and marker display. For information on the zebra display and marker display, refer to page 88.

This sets the display duration of the zebra display.

[AF SENSITIVITY]

[AF AREA WIDTH]

[WFM]

[ON]/[OFF]

[WFM TYPE]

[WAVE]/[VECTOR]/[WAVE/VECTOR]

[WFM POSITION]

[TOP/LEFT]/[TOP/RIGHT]/[BOTTOM/LEFT]/[BOTTOM/RIGHT]

[ZEBRA]

[ZEBRA 1]/[ZEBRA 2]*/[MARKER]*/[OFF]

[ZEBRA MODE]

[CONTINUE]: Displays the zebra display until it is switched to another zebra display setting.

[MOMENT]: Displays the zebra display for approximately 5 seconds.

- 155 -

You can switch the type of color bars to be displayed when you press the BARS button. (l 95)

When the default setting for [SYSTEM FREQ] is [59.94Hz]: This functions default setting is [TYPE 1]. When the default setting for [SYSTEM FREQ] is [50.00Hz]: This functions default setting is [TYPE 2].

Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31)

Enable/disable of the sub recording start/stop button on the handle can be switched.

When [ON] is selected, you can use Fast Zoom when operating the zoom with the zoom lever. (l 41)

Enable/disable of the sub zoom lever on the handle can be switched. Zoom speed will be different depending on the setting. The larger the value is, the faster the zoom speed becomes, and vice versa.

Changes the zoom magnification setting of Digital Zoom. (l 79)

[BARS TYPE]

[TYPE 1] [TYPE 2] [TYPE 3]

[SUB REC BUTTON]

[ACTIVE]/[INHIBIT]

[FAST ZOOM]

[ON]/[OFF]

[SUB ZOOM]

[OFF]/[1]/[2]/[3]/[4]/[5]/[6]/[7]

[DIGITAL ZOOM]

[k2]/[k5]/[k10]/[TOGGLE]

- 156 -

Set [REC FORMAT] or [OUTPUT FORMAT] to a setting with a picture size of 1920k1080 or below. (l 142, 147)

You can zoom in while maintaining the beauty of high-definition picture quality up to a magnification of 20k. (l 41)

Auto switch setting

All default settings are indicated with underlined text.

This enables/disables Auto Iris for Auto Iris Mode. (l 36)

This enables/disables AGC for Auto Iris Mode. (l 36)

Sets the maximum possible gain value for Auto Gain Mode. (l 62) (When [GAIN/ISO DISPLAY CHG] is set to [GAIN])

(When [GAIN/ISO DISPLAY CHG] is set to [ISO])

This enables/disables Auto Shutter for Auto Mode. (l 36)

[i.Zoom]

[ON]/[OFF]

: [AUTO SW] # desired setting

[A.IRIS]

[ON]/[OFF]

[AGC]

[ON]/[OFF]

[AGC LIMIT]

[3 dB]/[6 dB]/[9 dB]/[12 dB]/[15 dB]/[18 dB]/[21 dB]/[24 dB]

[ISO1000]/[ISO2000]/[ISO4000]/[ISO8000]

[AUTO SHUTTER]

[ON]/[OFF]

MENU

- 157 -

*1 This option is not displayed when [SYSTEM FREQ] is set to [50.00Hz]. *2 This option is not displayed when [SYSTEM FREQ] is set to [59.94Hz]. This sets the upper limit on the shutter speed for Auto Shutter Mode. (l 64)

You can record bright pictures even in dark places by slowing the shutter speed. Slow Shutter works in Auto Shutter Mode. (l 63) The shutter speed will be adjusted to one of the following values according to the ambient

brightness. The value will differ depending on the frame rate of the [REC FORMAT] or [OUTPUT FORMAT].

This item cannot be set during Freeze Frame. (l 81) When the shutter speed becomes 1/30, 1/24 or 1/25, the screen may be seen as if frames are

missed and after images may appear.

This enables/disables ATW for Auto Mode. (l 36)

This enables/disables Auto Focus for Auto Mode. (l 36)

[AUTO SHUTTER LIMIT]

[1/100]/[1/120]*1/[1/125]*2/[1/250]/[OFF]

[AUTO SLOW SHTR]

[ON]/[OFF]

Frame rates Shutter speed

59.94p/59.94i/29.97p 1/30 or more

50.00p/50.00i/25.00p 1/25 or more

23.98p/24.00p 1/24 or more

[ATW]

[ON]/[OFF]

[AF]

[ON]/[OFF]

- 158 -

Recording Setup

All default settings are indicated with underlined text.

Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) [SD CARD 1] and [SD CARD 2] can be selected separately to record motion pictures or still pictures. (l 32)

You can set relay/simultaneous/background/dual codec recording. Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) Insert SD cards to card slot 1 and card slot 2.

*1 This function is not available in the following cases: j In Variable Frame Rate Mode (l 91) j During the Interval Recording (l 162)

*2 This item is not available when different types of SD cards (SDHC Memory Card/SDXC Memory Card) are used.

*3 This function is not available in the following cases: j When [REC FORMAT] is set to a setting with a size of 4K (4096k2160) or UHD (3840k2160)

(l 142) j When the bit rate of [REC FORMAT] is above 50 Mbps

*4 Set [REC FORMAT] to a setting that allows you to use dual codec recording. (l 162)

Relay recording This is simple Relay Recording. It is possible to continuously record on the SD card in the other card slot even when the available capacity of the SD card runs out during the recording. is displayed beside the display of the SD card selected as the recording destination of

motion pictures in [MEDIA SELECT] (l 32). When the recording media is switched and Relay Recording starts, will disappear from the location and instead be displayed beside the other SD card display.

Even after switching of the recording media, you can replace the SD card that ran out of space with a new one and record the motion picture onto three or more SD cards. Since it may take a while for this unit to recognize a new SD card, replace the SD card that ran out of space when the SD card currently being used as a destination still has sufficient remaining recordable time.

: [RECORD SETUP] # desired setting

[MEDIA SELECT]

[2 SLOTS FUNC.]

[OFF]: Cancel the setting.

[RELAY REC]*1: Set the relay recording

[SIMULTANEOUS]*2: Set the simultaneous recording

[BACKGROUND]*1, 3: Set the background recording

[DUAL CODEC]*1, 2, 4: Set the dual codec recording

MENU

RELAY

RELAY

- 159 -

Simultaneous recording Same motion picture can be recorded on two SD cards. is displayed beside the display of the SD card selected as the recording destination of

motion pictures in [MEDIA SELECT] (l 32). If you set the recording destination of motion pictures to [SD CARD 1] in [MEDIA SELECT], they

will also be recorded to [SD CARD 2] simultaneously. We recommend that you perform simultaneous recording using SD cards of the same Speed

Class rating and capacity.

Background recording You can continue recording a motion picture by recording it on the SD card that is not set as a recording destination in [MEDIA SELECT] (l 32). When the recording destination of motion pictures is set to [SD CARD 1] in [MEDIA SELECT],

[SD CARD 2] will be used for background recording. The following instructions assume that the recording destination of motion pictures is set to [SD CARD 1].

is displayed beside the SD card display for card 2.

How to use background recording Register [BACKGROUND] to a USER button. (l 74) 1 Press the recording start/stop button to start recording. A motion picture will start being recorded to the two SD cards. ( will be displayed in red.) If you press the USER button to which [BACKGROUND] is registered, you can start recording

only to the SD card in card slot 2. For information on how to register a function to USER buttons, refer to page 74. For information

on how to use the USER button to which [BACKGROUND] is registered, refer to page 85. 2 Press the recording start/stop button again to stop recording. Recording to the SD card in card slot 1 will stop, but recording to the SD card in card slot 2 will

continue. You can repeat recording to the SD card in card slot 1 by pressing the recording start/stop button. You can stop background recording by pressing and holding the USER button to which

[BACKGROUND] is registered.

Dual codec recording You can make main and sub recordings in separate [REC FORMAT] settings. Sub recording records scenes in a picture quality lower than that of the [REC FORMAT] setting for main recording. If you set the recording destination of motion picture to [SD CARD 1] in [MEDIA SELECT] (l 32),

[SD CARD 1] will be used for main recording, while [SD CARD 2] will be used for sub recording. Set the sub recording scene setting in [DUAL CODEC REC]. The icon for the card used for main recording will be displayed with or .

SIMUL

BACKGR

BACKGR

DUAL 50M DUAL 8M

- 160 -

[2 SLOTS FUNC.] is not available when [OUTPUT BITS] is set to [4:2:2(10bit)]. (Relay recording) Destination to record still pictures will be switched to other SD card after performing the relay

recording. In addition, a message about the remaining card capacity will be displayed. Replace the SD card that ran out of space or set [2 SLOTS FUNC.] to [OFF].

(Simultaneous recording) Simultaneous recording will not be performed for still pictures. When performing simultaneous recording, even in the case where an error has occurred in one of

the SD cards and recording has stopped, recording can be continued using the other SD card. When one of the media reaches its maximum recording time, the simultaneous recording stops.

(Background recording) An alert sound is not emitted for background recording. If you record still pictures, their picture quality will differ from that during normal still picture

recording. Background recording stops in the following cases:

j When you have turned off this unit j When the SD card being used as a background recording destination runs out of space

If the SD card being used as a background recording destination runs out of space during motion picture recording, background recording does not restart automatically even if you replace the SD card.

(Dual codec recording) Main recording does not stop even if an error occurs in the memory card used for sub recording.

If an error occurs in the memory card used for main recording, the recording stops.

This sets the sub recording scene settings for dual codec recording. For information on dual codec recording, refer to page 160.

Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) Set [REC FORMAT] to a setting with a size of UHD (3840k2160). (l 142)

Sub recording scenes will be recorded with the following settings: j Recording is performed with a size setting of FHD (1920k1080) j When [FHD 50Mbps] is selected, the [REC MODE] setting selected for sub recording will be

the same as the setting selected for main recording (MOV/MP4). j Recording is performed at the same frame rate as that of the [REC FORMAT] setting for main

recording.

[DUAL CODEC REC]

[FHD 50Mbps]: Performs recording at a bit rate of 50Mbps. Scenes can be saved in either MOV or MP4 format.

[FHD 8Mbps]: Performs recording at a bit rate of 8Mbps. Scenes can be saved in MOV format.

- 161 -

[REC FORMAT] settings that support main recording of dual codec recording

(When [DUAL CODEC REC] is set to [FHD 50Mbps])

(When [DUAL CODEC REC] is set to [FHD 8Mbps])

This function is not available in the following cases: j When [OUTPUT BITS] is set to [4:2:2(10bit)] j In Variable Frame Rate Mode (l 91) j When [REC MODE] is set to [AVCHD] (l 141) j When the size of [REC FORMAT] is set an option other than UHD (3840k2160) j During the Interval Recording (l 162)

A scene that moves slowly for long period of time is recorded frame by frame with an interval, and is recorded as a short time motion picture. One frame is recorded every recording interval that is set. The number of frames per second differs depending on the frame rate of [REC FORMAT].

j When the frame rate is set to 59.94i or 29.97p: 30 frames for a scene of 1 second j When the frame rate is set to 50.00i or 25.00p: 25 frames for a scene of 1 second j When the frame rate is set to 24.00p or 23.98p: 24 frames for a scene of 1 second

Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31)

[I-] is displayed on the screen. The icon changes to [I-REC] after recording starts. After recording, the setting of Interval Recording is canceled. Audio cannot be recorded.

Recording mode System frequency setting Recording format

MOV, MP4 [59.94Hz] UHD 2160/29.97p 100M,

UHD 2160/23.98p 100M

[50.00Hz] UHD 2160/25.00p 100M

Recording mode System frequency setting Recording format

MOV, MP4

[59.94Hz]

UHD 2160/29.97p 100M, UHD 2160/23.98p 100M, FHD 1080/59.94p , FHD 1080/59.94p 100M, FHD 1080/29.97p , FHD 1080/23.98p

[50.00Hz]

UHD 2160/25.00p 100M, FHD 1080/50.00p , FHD 1080/50.00p 100M, FHD 1080/25.00p

[INTERVAL REC]

[OFF]/[1 SEC.]/[10 SEC.]/[30 SEC.]/[1 MINUTE]/[2 MINUTES]

- 162 -

h is an abbreviation for hour, min for minute and s for second. These times are approximations. Maximum recordable time is 168 hours.

Still picture recording cannot be used. This function is not available in the following cases:

j When [OUTPUT BITS] is set to [4:2:2(10bit)] j During Freeze Frame (l 81) j PRE-REC is used (l 86) j In Variable Frame Rate Mode (l 91)

When Interval Recording is set, the [REC FORMAT] setting changes as follows. In addition, the settings for [REC MODE] and [REC FORMAT] cannot be changed. j When [REC FORMAT] is set to [4K 2160/59.94p 100M]:

You cannot change this setting to another one. j When the size of the [REC FORMAT] setting is UHD (3840k2160):

[UHD 2160/29.97p 100M]*1 or [UHD 2160/25.00p 100M]*2 j When the size of the [REC FORMAT] setting is FHD (1920k1080):

[FHD 1080/29.97p 50M]*1 or [FHD 1080/25.00p 50M]*2 j When [REC FORMAT] is set to [AVCHD]:

[HA 1080/59.94i]*1 or [HA 1080/50.00i]*2 *1 When [SYSTEM FREQ] (l 141) is set to [59.94Hz] *2 When [SYSTEM FREQ] is set to [50.00Hz] [INTERVAL REC] is canceled in the following cases.

j If you turn the unit off j If you press the THUMBNAIL button j When [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

The shortest motion picture recording time is approx. 2 second. Color balance and focus may not be adjusted automatically depending on light sources or

scenes. If so, manually adjust these settings. (l 44, 55) We recommend connecting the AC adaptor to this unit when recording images for a long period of

time.

Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31)

This allows the recording of an image and audio to start before you press the recording start/stop button. AVCHD scenes will be recorded from approximately 3 seconds before the operation, while MOV/MP4 will be recorded from approximately 4 seconds before the operation. (l 86)

Setup example Setup time (recording interval) Recording time Recorded time

Sunset 1 s 1 h 2 min

Blooming 30 s 3 h 12 s

[PRE-REC]

[ON]/[OFF]

- 163 -

Selecting [ON] enables Infrared Recording Mode, allowing you to record images in the dark. (l 84)

Switch to Manual Focus. (l 44)

You can register a focus position to Focus Transition. (l 52)

You can set the length of time in which the focus will shift during Focus Transition. (l 54)

This functions default setting is 2 seconds.

You can start recording and Focus Transition simultaneously. (l 54)

You can set the length of time before Focus Transition starts. (l 55)

Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31)

You can stamp the date and time of recording on the images you record. appears on the screen.

The display mode and format of the date and time of recording to be stamped vary depending on the settings for [DATE/TIME] and [DATE FORMAT]. (l 173)

The month of the date and time of recording is recorded in English.

[INFRARED REC]

[ON]/[OFF]

[FOCUS TRANSITION]

[SET][OFF]

[FOCUS TRANSITION TIME]

[DIRECT]/[2-15 SEC.]/[20 SEC.]/[30 SEC.]/[45 SEC.]/[60 SEC.]/[90 SEC.]

[FOCUS TRANSITION REC]

[1]/[2]/[3]/[OFF]

[FOCUS TRANSITION WAIT]

[0 SEC.]/[5 SEC.]/[10 SEC.]

[TIME STAMP]

[ON]/[OFF]

- 164 -

In the following cases, even when [TIME STAMP] is set to [ON], the date and time of recording are not displayed: j When [OUTPUT BITS] is set to [4:2:2(10bit)] j When [REC FORMAT] is set to [SA 480/59.94i] or [SA 576/50.00i] (l 142) j When [2 SLOTS FUNC.] is set to [DUAL CODEC] (l 159) j When [DATE/TIME] is set to [OFF] j During Freeze Frame (l 81) j In Variable Frame Rate Mode (l 91) j When this unit is connected to the SDI OUT terminal of the external device and the external

output resolution is set to PsF (l 116) Even when [VIDEO OUT OSD] is set to [OFF], the date and time of recording are displayed on

the external monitor screen. (l 115) It is not possible to stamp the date and time of recording during normal still picture recording. The date and time of recording displayed during [TIME STAMP] recording and the date and time

displayed during the playback of the image may not exactly be the same.

Set [SYSTEM FREQ] to [59.94Hz]. (l 141)

Selects the compensation mode for the time code. (l 71)

Sets the way the time code will move. (l 71)

Initial value of the time code can be set. (l 72)

Set [REC MODE] to [AVCHD]. (l 141) User Information can be set. (l 72)

You can synchronize the time code of the external device with that of this unit. (l 73)

[DF MODE]

[DF]/[NDF]

[TCG]

[FREE RUN]/[REC RUN]

[TC PRESET]

[UB PRESET]

[EXT TC LINK]

[MASTER]/[SLAVE]

- 165 -

Audio Setup

All default settings are indicated with underlined text.

Reduces the level of low-pitched sound for audio channel 1.

You may not see the full effect depending on the recording conditions.

Reduces the level of low-pitched sound for audio channel 2.

You may not see the full effect depending on the recording conditions.

Set the CH1/CH2 switch to MANU. (l 68) Set [AUDIO ALC CH1]/[AUDIO ALC CH2] to [ON]. (l 69)

If you set this item to [ON], when ALC works for either of the audio channels, it will also work for the other audio channel. (l 69)

If you set this item to [ON], you can reduce the audio noise of audio channel 1. It will record with natural sound when set to [OFF]. (l 69)

If you set this item to [ON], you can reduce the audio noise of audio channel 2. It will record with natural sound when set to [OFF]. (l 69)

: [AUDIO SETUP] # desired setting

[AUDIO LOW CUT CH1]

[ON]/[OFF]

[AUDIO LOW CUT CH2]

[ON]/[OFF]

[AUDIO ALC LINK]

[ON]/[OFF]

[AUDIO ALC CH1]

[ON]/[OFF]

[AUDIO ALC CH2]

[ON]/[OFF]

MENU

- 166 -

Sets the input level of the audio equipment connected to AUDIO INPUT1 terminal (XLR 3 pin).

Sets the input level of the audio equipment connected to AUDIO INPUT2 terminal (XLR 3 pin).

Sets the input level of the external microphone connected to AUDIO INPUT1 terminal (XLR 3 pin).

Sets the input level of the external microphone connected to AUDIO INPUT2 terminal (XLR 3 pin).

Output Setup Different menu items are displayed depending on whether this unit is in Recording Mode or Playback Mode. All default settings are indicated with underlined text.

This changes the external output destination. (l 115)

This changes the way in which images are output to an external device. (l 115)

[INPUT1 LINE LEVEL]

[+4dBu]/[0dBu]

[INPUT2 LINE LEVEL]

[+4dBu]/[0dBu]

[INPUT1 MIC LEVEL]

[-40 dB]/[-50 dB]/[-60 dB]

[INPUT2 MIC LEVEL]

[-40 dB]/[-50 dB]/[-60 dB]

: [OUTPUT SETUP] # desired setting

[OUTPUT SEL]

[HDMI]/[SDI]/[SDI+AV]

[RESOLUTION]

[SYSTEM]/[1080p]/[1080i]/[DOWN CONV.]

MENU

- 167 -

This enables/disables a function that controls recording performed with an external device connected to the SDI OUT terminal.

When [HDMI TC OUTPUT] is set to [ON], you can also control an HDMI device. (l 170) It is not possible to control recording performed with an external device connected to the

SDI OUT terminal in the following cases: j When [REC FORMAT] is set to [SA 480/59.94i] or [SA 576/50.00i] (l 142) j When [RESOLUTION] is set to [DOWN CONV.] (l 115)

When [ON] is selected, you can control recording performed with this unit and an external device using the recording start/stop button.

When [ON] is selected, EDH is superimposed on images of SD signals (480i and 576i) output from the SDI OUT terminal. (In Playback Mode)

Touch the play mode select icon, and set this unit to Motion Picture Playback Mode. (l 101)

This adjusts the gain value of audio signals output from the SDI OUT terminal. Set [OUTPUT SEL] to [SDI] or [SDI+AV]. (l 115) (In Playback Mode)

Touch the play mode select icon, and set this unit to Motion Picture Playback Mode. (l 101)

[SDI REMOTE]

[ON]/[OFF]

[REMOTE REC LINK]

[ON]: Controls recording performed with this unit and an external device using the recording start/stop button.

[OFF]: Controls recording performed with an external device using the USER button function [AUTO REC]. (l 90)

[SDI EDH]

[ON]/[OFF]

[SDI AUDIO GAIN CHG]

[0 dB]/[-6 dB]/[-12 dB]

- 168 -

This function allows you to select how to display images with a 16:9 aspect ratio on an external monitor with a 4:3 aspect ratio. Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31) Set [RESOLUTION] to [DOWN CONV.]. (l 115)

This item is fixed to [SQUEEZE] in the following cases: j When [REC FORMAT] is set to a setting with a size of 4K (4096k2160) or UHD (3840k2160) j When [REC FORMAT] is set to [SA 480/59.94i] or [SA 576/50.00i]

Example of images with a [17:9] or [16:9] aspect ratio on an external monitor (4:3):

* The screen is displayed this way when [RESOLUTION] is set to [DOWN CONV.] and [DOWN CONV.] is set to [LETTERBOX]. (l 169)

When [DOWN CONV.] is set to [SIDE CROP], the sides of an image will be cut off, causing some icons on the external monitor to be hidden from the external monitor screen.

This sets a frame rate when outputting scenes in the recording format [UHD 2160/59.94p 150M] or [UHD 2160/50.00p 150M] from the HDMI OUT terminal.

(When [SYSTEM FREQ] is set to [59.94Hz])

(When [SYSTEM FREQ] is set to [50.00Hz])

[DOWN CONV.]

[SIDE CROP]: Outputs images so that they are fit to the height of the external monitor screen.

[LETTERBOX]: Outputs images so that they are fit to the width of the external monitor screen.

[SQUEEZE]: Outputs horizontally-compressed images so that they are fit to the screen.

[RESOLUTION] setting

[SYSTEM]/[1080p]/[1080i] [DOWN CONV.]

*

[HDMI UHD OUTPUT LIMIT]

[59.94p]: Outputs scenes in 2160/59.94p.

[29.97p]: Outputs scenes in 2160/29.97p

[50.00p]: Outputs scenes in 2160/50.00p.

[25.00p]: Outputs scenes in 2160/25.00p.

- 169 -

Switches the output setting of time code information when this unit is connected to another device (HDMI-SDI converter, etc.) with an HDMI cable. (In Playback Mode)

Touch the play mode select icon, and set this unit to Motion Picture Playback Mode. (l 101)

When [ON] is selected, you can adjust the headphone volume in Recording Mode with the jog dial. (l 100)

Selects the test tone output when color bars are displayed. (l 95)

This sets the setup level of 480i image signals. Set [SYSTEM FREQ] to [59.94Hz]. (l 141, 178)

AG-DVX200PJ/PB: This functions default setting is [7.5%A]. AG-DVX200EJ/EN/ED/PX: This functions default setting is [0%].

This sets how to turn on/off the LCD monitor and viewfinder. (l 24)

[HDMI TC OUTPUT]

[ON]/[OFF]

[VOLUME]

[ON]/[OFF]

[TEST TONE]

[OFF]: Does not output a test tone.

[LEVEL 1]: Outputs a high volume test tone.

[LEVEL 2]: Outputs a low volume test tone.

[VIDEO SETUP]

[0%]/[7.5%A]

[LCD/EVF OUTPUT]

[AUTO]/[LCD]/[EVF]

- 170 -

Display setting Different menu items are displayed depending on whether this unit is in Recording Mode or Playback Mode. All default settings are indicated with underlined text.

Selects the brightness level of the left-leaning zebra patterns on the screen. 1 Touch [ZEBRA DETECT 1]. Touch [YES]. 2 Touch / to adjust settings. You can select a value between 50% and 105%. 3 Touch [EXIT] to complete the setting.

This functions default setting is 80%.

Selects the brightness level of the right-leaning zebra patterns on the screen. 1 Touch [ZEBRA DETECT 2]. Touch [SET]. 2 Touch / to adjust settings. You can select a value between 50% and 105%. 3 Touch [EXIT] to complete the setting. You can display [ZEBRA 2] after setting the level. (l 88, 155)

This functions default setting is 100%.

Displaying of the luminance level display marker can be switched. Marker can be displayed when set to [ON]. (l 88, 155)

: [DISP SETUP] # desired setting

[ZEBRA DETECT 1]

[ZEBRA DETECT 2]

[SET]/[OFF]

[MARKER]

[ON]/[OFF]

MENU

- 171 -

You can check if the image is level while recording motion pictures and still pictures. The function can also be used to estimate the balance of the composition. The guidelines do not appear on the images actually recorded.

The setting changes as follows when using Focus Assist. (l 48) j The guidelines are not displayed. (They are displayed on the external monitor when this unit is

connected to the external monitor.) j The setting cannot be changed.

Display of the range that can be displayed with the external monitor (safety zone A) can be switched.

* When [REC FORMAT] is set to [SA 480/59.94i] or [SA 576/50.00i] and [ASPECT CONVERT] is set to [SIDE CROP] (l 142, 148)

The safety zone is not displayed on the images that is actually recorded.

Displays/hides the center marker.

Selects the operation of the Recording Counter during recording. (l 73)

Changes the setting for the shutter speed display.

[GUIDE LINES]

/ / /[OFF]

[SAFETY ZONE]

Aspect ratio [SAFETY ZONE]

16:9 [16:9 90%]/[4:3]/[14:9]/[1.85:1]/[17:9]/ [2:1]/[2.35:1]/[2.39:1]/[OFF]

4:3* [4:3 90%]/[4:3]/[OFF]

(When [16:9 90%] is set)

[CENTER MARKER]

[ON]/[OFF]

[REC COUNTER]

[TOTAL]/[SCENE]

[SHUTTER DISPLAY CHG]

[sec]: Displays shutter speeds as time.

[deg]: Displays shutter speeds as open angles of the shutter.

- 172 -

This changes the gain value unit in Recording Mode.

This changes the units of zoom and focus values.

(In Recording Mode) Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31)

The information displayed on the screen (operation icon and counter display etc.) can be displayed/ not displayed on the external monitor. (l 115)

It is possible to change the date and time display mode.

It is possible to change the date format. AG-DVX200PJ/PB: This functions default setting is [M/D/Y].

AG-DVX200EJ/EN/ED: This functions default setting is [D/M/Y]. AG-DVX200PX: This functions default setting is [Y/M/D].

This function displays the horizontal/vertical tilt of the unit with the electronic level. (l 85)

[GAIN/ISO DISPLAY CHG]

[GAIN]: Displays the gain value in dB.

[ISO]: Displays the gain value in ISO.

[ZOOM/FOCUS]

[ZOOM/FOCUS] setting Zoom value Focus value

[NUMBER] A value between 0 and 99 is displayed.

[mm/feet] Millimeter Feet

[mm/m] Millimeter Meter

[OFF] No value is displayed.

[VIDEO OUT OSD]

[ON]/[OFF]

[DATE/TIME]

[OFF]/[TIME]/[DATE]/[DATE&TIME]

[DATE FORMAT]

[Y/M/D]/[M/D/Y]/[D/M/Y]

[LEVEL GAUGE]

[ON]/[OFF]

- 173 -

A graph with brightness as horizontal axis and number of pixels at that brightness as vertical axis is displayed. It is possible to determine the exposure of the whole image by looking at the distribution in the graph. (l 79)

(In Playback Mode) Touch the play mode select icon, and set this unit to Motion Picture Playback Mode. (l 101)

Select to display the audio level meter.

Display relating to lens can be switched. (Zoom Display, Optical Image Stabilizer, ND filter, Focus Display, White Balance, Iris, Gain, Auto Iris, Shutter Speed)

Display can be switched between the remaining recordable time of the SD card and the remaining battery capacity indication.

This shows or hides indications on the screen except for [USER BUTTON DISPLAY], [GUIDE LINES], [SAFETY ZONE], [CENTER MARKER], [DATE/TIME], [AUDIO LEVEL METER], [LENS STATUS] and [CARD & BATTERY].

Switches the brightness on the LCD monitor. (l 26)

[HISTOGRAM]

[ON]/[OFF]

[AUDIO LEVEL METER]

[ON]/[OFF]

[LENS STATUS]

[ON]/[OFF]

[CARD & BATTERY]

[ON]/[OFF]

[OTHER DISPLAY]

[ON]/[OFF]

[LCD BACKLIGHT]

[HIGH]/[LOW]

- 174 -

It adjusts brightness and color density on the LCD monitor. (l 26)

The default settings are as follows: j [COLOR]: 0 j [BRIGHTNESS]: 0 j [CONTRAST]: 0

Adjusts the brightness and color intensity of the viewfinder. (l 27)

The default settings are as follows: j [COLOR]: 0 j [BRIGHTNESS]: 0 j [CONTRAST]: 0

Adjusts the eye sensor sensitivity. (l 28)

This functions default setting is s4.

Switches the mirror function of the LCD monitor when recording yourself. (l 28) The image on the LCD monitor is displayed mirrored horizontally during recording of yourself when it is set to [MIRROR].

The recording images or playback images on the viewfinder can be selected between color/black and white. (l 28)

[LCD SET]

[COLOR]/[BRIGHTNESS]/[CONTRAST]

[EVF SETTING]

[COLOR]/[BRIGHTNESS]/[CONTRAST]

[EYE SENSOR]

[SELF SHOOT]

[MIRROR]/[NORMAL]

[EVF COLOR]

[ON]/[OFF]

- 175 -

Setting this item to [ON] helps you achieve focus easier by emphasizing the outlines of an image displayed on the LCD monitor and viewfinder. (l 45)

Adjusts the emphasis strength for [EVF/LCD DETAIL]. (l 45)

This functions default setting is 0.

Sets the peaking frequency for [EVF/LCD DETAIL]. (l 45)

Other Functions Different menu items are displayed depending on whether this unit is in Recording Mode or Playback Mode. All default settings are indicated with underlined text.

The SD card or the external media device can be formatted. (l 32, 127) Please be aware that if a medium is formatted, then all the data recorded on the medium will be

erased and cannot be restored. Back up important data on a PC etc. (l 122)

(In Recording Mode) Set [OUTPUT BITS] to [4:2:2(8bit)]. (l 31)

The used space and remaining recordable time of the SD card can be checked. Touching [CHANGE MEDIA] switches the unit between the display for the SD card 1 and the

display for the SD card 2. Only in Recording Mode, remaining recordable time for the selected recording format is

displayed. Touch [EXIT] to close the indication.

The SD card requires some space to store information and manage system files, so the actual usable space is slightly less than the indicated value. The usable space is generally calculated as 1 GB=1,000,000,000 bytes. The capacities of this unit, PCs and software are expressed as 1 GB=1,024k1,024k1,024=1,073,741,824 bytes. Therefore, the indicated value of the capacity appears to be smaller.

[EVF/LCD DETAIL]

[ON]/[OFF]

[EVF/LCD PEAK LEVEL]

[EVF/LCD PEAK FREQ.]

[HIGH]/[LOW]

: [OTHER FUNCTION] # desired setting

[FORMAT MEDIA]

[MEDIA STATUS]

MENU

- 176 -

The recording lamp lights up during recording. When this is set to [OFF], it does not light during recording.

Set date and time. (l 29)

Set the time difference from Greenwich Mean Time. (l 29)

Touch screen operation, start and stop of recording can be confirmed with this sound. When [OFF] is selected, the sound is not output at the start/end of recording, etc. 2 Beeps for 4 times When an error occurs. Check the message displayed on the screen. (l 185)

When about 5 minutes have passed without any operation, this unit automatically turns off to save battery life. This unit will not automatically turn off even if the [ECONOMY (BATT)] is set to [ON] in following

cases: j PRE-REC is used (l 86, 163) j When [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

When connected to AC adaptor about 15 minutes have passed without any operation, this unit automatically turns off. This unit will not automatically turn off even if the [ECONOMY (AC)] is set to [ON] in following

cases: j PRE-REC is used (l 86, 163) j When [USB MODE SELECT] is set to [DEVICE] and this unit is connected to a PC. (l 122)

[REC LAMP]

[FRONT]/[REAR]/[BOTH]/[OFF]

[CLOCK SET]

[TIME ZONE]

[ALERT SOUND]

[OFF]/ (Volume low)/ (Volume high)

[ECONOMY (BATT)]

[ON]/[OFF]

[ECONOMY (AC)]

[ON]/[OFF]

- 177 -

Set the system frequency of this unit. (l 141)

The units USB terminal to which a USB Cable will be connected can be switched. Switch the terminal according to the shape of the USB Cables plug you intend to connect to the unit.

The menu settings or [CUSTOMIZE SCENE] are reset to the default. (l 130)

* Settings for [CLOCK SET], [TIME ZONE] and [SYSTEM FREQ] will not be changed.

Returning all settings to the default is not possible during Freeze Frame. (l 81)

Set the file number of the MOV/MP4 and still picture recorded next to 0001. Folder number is updated and file number will start from 0001. (l 123) To reset the folder number, format the SD card, and then perform [NUMBER RESET].

You can select the language on the screen display and the menu screen.

[SYSTEM FREQ]

[USB MODE SELECT]

[HOST]: For connecting to the USB HOST terminal (Type A) of the unit

[DEVICE]: For connecting to the USB DEVICE terminal (Type Micro-B) of the unit

[INITIAL SET]

[ALL]: This is for initializing all menus.*

[SCENE]: This is for initializing the setting of customize scene.

[NO]: This is for not performing initialization.

[NUMBER RESET]

[LANGUAGE]

- 178 -

Maintenance

The version of the firmware of this unit is displayed.

The firmware of this unit is updated. (l 193)

This displays the operation time of this unit, how many times the zoom lever has been operated, and how many times the zoom motor has worked.

Video Setup

All default settings are indicated with underlined text. Press the THUMBNAIL button to switch this unit to the Playback Mode. Touch the play mode select icon, and set this unit to Motion Picture Playback Mode.

(l 101)

Playback of the first scene starts after playback of the last scene finishes when set to [ON]. (l 107)

If playback of a scene was stopped halfway, the playback can be resumed from where it was stopped when set to [ON]. (l 107)

Scenes can be protected so that they are not deleted by mistake. (Even if you protect some scenes, formatting the SD card will delete them.) (l 110)

Deletes a scene. (l 109)

: [MAINTENANCE] # desired setting

[VERSION]

[UPDATE]

[HOUR METER]

: [VIDEO SETUP] # desired setting

[REPEAT PLAY]

[ON]/[OFF]

[RESUME PLAY]

[ON]/[OFF]

[SCENE PROTECT]

[DELETE]

MENU

MENU

- 179 -

Picture Setup

Press the THUMBNAIL button to switch this unit to the Playback Mode. Touch the play mode select icon, and set this unit to Still Picture Playback Mode. (l 101)

Still pictures can be protected so that they are not deleted by mistake. (Even if you protect some still pictures, formatting the SD card will delete them.) (l 110)

Deletes a still picture. (l 109)

Copy

Press the THUMBNAIL button to switch this unit to the Playback Mode.

This copies all scenes and still pictures recorded with this unit that have never been copied to another device to the external media device connected to this unit. (l 127)

This allows you to select and copy the scenes/still pictures. You can copy between the SD cards in this unit or from either of them to the external media device. (l 111, 128)

: [PICT. SETUP] # desired setting

[SCENE PROTECT]

[DELETE]

: [COPY] # desired setting

[DIFFERENTIAL COPY]

[SELECT COPY]

[ ]/[ ]/[ ]/[ ]

MENU

MENU

- 180 -

Recording indications

Display

Indications

Example: Display in English

1/100

OPEN

60:59.94p FBC VFR

H.SENS I- REC

150M

AF50

D 5X

Z00 NOV 15 2015 15:30:00

0dB

99%

ATW ND1/64

SHUTTER

DRS

TC 00:00:00.00 R 1h20m R 1h20m

A

TC 00:00:00.00/TC 00:00:00:00

Counter display (l 70)

I- Interval Recording (l 162)

I-REC (Red) Interval Recording (Recording)

P- PRE-REC (l 86, 163)

P-REC (Red) PRE-REC (Recording)

REC (Red) Recording

REC (Flashing red)

Recording pause

Recording is not possible. (l 31)

, Automatic recording (l 90)

Auto Mode (l 36)

Remaining battery power (l 19)

, (White)

Recording to card possible (motion picture)

, (Green)

Card is being recognized (motion picture)

R 1h20m Remaining time for motion picture recording (l 33)

REC

Relay recording (l 159)

Simultaneous recording (l 160)

Background recording (l 160)

, Dual codec recording (l 160, 161)

H.SENS High sensitivity recording mode (l 148)

V-Log L V-Log L Mode (l 140)

Output bits (l 31)

Area Mode (l 82)

AF area width adjustment (l 47, 90)

Freeze Frame (l 81)

, Image Stabilizer (l 42)

DRS DRS (l 81, 139)

Infrared recording (l 84, 164)

RELAY

SIMUL

BACKGR

DUAL 50M DUAL 8M

4:2:2 10bit

AF-AREA

Freeze

- 181 -

B

, , , , , , , ,

Recording format (l 142)

, , Output format (l 147)

ALL-I, 150M, 100M, 50M Bit rate (l 142)

D 2X, D 5X, D 10X

Digital Zoom (l 79)

, Recording mode (l 141)

60:59.94p/50:50.00p Frame rate in Variable Frame Rate Mode (l 91, 131)

59.94p, 59.94i, 50.00p, 50.00i, 29.97p, 25.00p, 24.00p, 23.98p Frame rate (l 142)

FBC Flash band compensation (l 86, 140)

ATW, LOCK, P3200K, P5600K, VAR, Ach, Bch White Balance (l 55)

VFR Variable Frame Rate mode (l 91, 131)

LT.BOX When [ASPECT CONVERT] is set to [LETTERBOX] (l 148)

ND 1/4, ND 1/16, ND 1/64

ND filter (l 96)

99% Luminance level (l 82, 88)

Luminance display frame (l 88)

SA

Center Marker (l 172)

AGC, ISO AUTO, 0dB, ISO500

Gain value (l 61)

SHUTTER Multi Manual Function (l 99)

1/100, 5.0d Shutter speed (l 63)

1/100.0 Synchro Scan (l 65)

- 182 -

C

Time Stamp recording in progress (l 164)

2015 NOV 15 15:30:00 NOV 15 2015 15:30:00 15 NOV 2015 15:30:00 Time Stamp (l 164)

NOV 15 2015 15:30:00 15 11 2015 15:30:00 2015 11 15 15:30:00 Date indication Time indication (l 29)

Focus Transition bar (l 53)

Focus Macro (l 94, 154)

AF50, MF50, MA50, 00, 00, 00 Focus (l 44)

When [AUDIO ALC CH1] is enabled (l 69)

When [AUDIO ALC CH2] is enabled (l 69)

When [AUDIO ALC CH1], [AUDIO ALC CH2] are enabled (l 69)

When [AUDIO ALC CH1], [AUDIO ALC CH2], [AUDIO ALC LINK] are enabled (l 69)

When [AUDIO ALC CH1], [AUDIO ALC CH2], and [AUDIO ALC LINK] are enabled and audio cannot be recorded. (l 92)

Audio level meter (l 68)

Sound recording disabled (l 92)

Auto iris mode (l 59)

Backlight Compensation (l 77)

Spotlight (l 77)

OPEN, F2.0 Iris value (l 59)

S E

ALC

A.REC

Z00 Zoom magnification (l 40)

iZ99 1.00 i.Zoom magnification (l 40)

99 Fast Zoom (l 40)

, (White)

Card recording possible status (still picture)

, , , , , Number of recording pixels for still pictures (l 34, 106)

In Playback Mode, the picture size is not displayed for still pictures recorded with other products that have different picture sizes from the sizes shown above.

R3000 Remaining number of still pictures (l 34)

(Red) Recording still picture

M8.8 M8.3 2.1 M M0.9 0.3M M0.2

- 183 -

Playback indications Example: Display in English

Indication of connection to the external media device

Indication of connection to other devices

Confirmatory indications

1, ;, 5, , 6, , 7, 8, 9, :, D, E, ;1, 2;

Display during playback (l 101, 105)

TC 00:00:00.00/TC 00:00:00:00

Counter Display (l 70)

15:30 Time indication (l 29)

NOV 15 2015 15 11 2015 2015 11 15

Date indication (l 29)

No.0010 Scene Number

Repeat Playback (l 107)

Resume Playback (l 107)

100-0001 Still picture folder/file name

Protected motion pictures/still pictures (l 110)

, , Recording mode (When thumbnails are displayed) (l 101)

, , , , , , , , , ,

Recording format (When thumbnails are displayed) (l 101, 142)

10 Scene Number (In 9-scene display in thumbnail mode) (l 101)

TC 00:00:00.00 No.0010 59.94p150M

NOV 15 2015 15:30

ICONS

4K UHD FHD DU50 DU8 PH PS HA

HE PM SA

Playback of the external media device (l 129)

Accessing the card (l 123)

(Time display)

The built-in battery is low. (l 29)

Warning for recording of yourself (l 28)

SD card is not inserted.

SD card is write-protected.

SD card is non-compatible.

SD card is full.

Playback-only SD card

- 184 -

Major confirmation/error messages to be indicated on the screen in text.

Display

Messages

During recording/playback

Display Description Behavior and cause

CHECK CARD. The SD card is not supported by this unit.

Check the SD card.

THIS CARD CANNOT RECORD IN VIDEO MODE.

This is displayed when the SD card has a capacity of less than 4 GB.

Use an SD card with a capacity of 4 GB or more.

INCOMPATIBLE CARD. CHECK CARD SPEED.

This is displayed if the maximum writing speed of the SD card is not fast enough.

The operation will continue.

Use an SD card with a maximum writing speed that is fast enough.

CANNOT BE USED DUE TO INCOMPATIBLE DATA.

The SD card cannot be used with this unit.

Insert a recordable SD card.

CANNOT RECORD - INCOMPATIBLE CONTROL DATA.

The content versions do not match. This is displayed when the SD card contains scenes recorded with another device, for example.

Match the device and content version.

ERROR OCCURRED. RECORDING IS STOPPED.

This is displayed when the SD card is removed during recording or data cannot be written to the SD card correctly.

Check the SD card.

CANNOT RECORD.THE NUMBER OF SCENES HAS EXCEEDED THE MAXIMUM LIMIT.

No additional scenes can be recorded to the SD card.

Delete unnecessary scenes, or use a new SD card.

CANNOT RECORD - DATE CAPACITY IS FULL. Cannot record - Playlist capacity is full.

This is displayed when you try to record in excess of the maximum number of scenes allowed for one SD card.

The operation will stop. Replace the SD card or

delete unnecessary scenes.

INVALID This is displayed when the operation is invalid.

Before performing the operation, wait until this unit is ready for it.

- 185 -

ERROR - UNABLE TO REPAIR DATA.

This is displayed when the management information cannot be recovered.

Check the SD card.

CANNOT USE SD CARD IN VIDEO MODE, CONTROL DATA ERROR.

This is displayed when the management information cannot be recovered.

The operation will stop. Use another SD card to

perform recording.

CONTROL DATA ERROR HAS BEEN DETECTED. (SD CARD)

Defective management information has been found.

The management information will be automatically recovered after this message is displayed.

VFR ON, NO AUDIO RECORDING

Audio cannot be recorded if you change the frame rate when using Variable Frame Rate Mode.

To record audio, disable Variable Frame Rate Mode.

CANNOT REC Recording cannot be performed with this unit when [OUTPUT BITS] is set to [4:2:2(10bit)].

To perform recording with this unit, set [OUTPUT BITS] to [4:2:2(8bit)].

CANNOT PLAY. This is displayed when an error in the recording folder name or file name has occurred, for example.

Check the SD card.

Display Description Behavior and cause

- 186 -

During thumbnail and menu operation

Display Description Behavior and cause NO DATA. There are no scenes in the

currently selected recording mode option and recording format option.

Select a recording mode option or recording format option containing recorded scenes.

CANNOT REC IN THIS MODE.

Recording cannot be performed with this unit when [OUTPUT BITS] is set to [4:2:2(10bit)].

To perform recording with this unit, set [OUTPUT BITS] to [4:2:2(8bit)].

CANNOT DELETE. The content versions do not match. This is displayed when you try to delete scenes recorded with another device, for example.

Match the device and content version.

CARD ERROR. PLEASE REFORMAT.

This is displayed when the SD card cannot be formatted.

Check the SD card. Replace the SD card in the card

slot at which the error has occurred.

UNABLE TO FORMAT. Formatting is not possible due to, for example, a problem with the SD card.

Check the SD card.

Cannot delete data on card.

The SD card cannot be formatted.

Check the SD card.

CANNOT PROTECT. The content versions do not match. This is displayed when you try to set protection for scenes recorded with another device, for example.

Match the device and content version.

CANNOT RESET NUMBER.

The SD card cannot be used with this unit.

Insert a recordable SD card.

- 187 -

During USB Device mode

Display Description Behavior and cause DISCONNECT USB CABLE.

An error has occurred while accessing the SD card, or the OS is not supported.

Check the SD card. Check to see if the OS is

supported.

During USB Host mode

Display Description Behavior and cause CANNOT CHECK CONNECTED DEVICE. DISCONNECT THE USB CABLE FROM THIS UNIT.

This is displayed when the device is connected to this unit with a product such as a USB hub.

Do not connect the devices with a product such as a USB hub. Connect to this unit directly.

FORMATTING FAILED. The external media device cannot be formatted.

Change the connected external media device.

During copying between SD cards or copying to an external media device

Display Description Behavior and cause PLEASE CHECK THE EXTERNAL MEDIA.

Copying cannot be performed due to, for example, a problem with the copy destination media device.

Check the copy destination media device.

THIS SCENE CANNOT BE COPIED. Cannot copy: contains recordings from other devices.

This is displayed when one or more of the scenes you are trying to copy cannot be played back on this unit.

Copy scenes except for the ones that cannot be copied.

COPY FAILED. PLEASE CHECK THE CARD.

An error has occurred while accessing the SD card.

Check the SD card.

Cancel card lock to write information.

The write-protect switch of the copy destination SD card is locked.

Unlock the write-protect switch of the SD card.

- 188 -

It is not a malfunction in following cases

Others

Troubleshooting

The lens, the viewfinder or LCD monitor fog up.

This is due to condensation. This is not a malfunction. Please refer to page 2.

A clicking sound is heard when the unit is shaken.

This is the sound of the lens moving and is not a defect. This sound will no longer be heard when the unit is turned on and switch to Recording Mode.

Object seems to be warped. Object seems to be warped slightly when the object moves across the image very fast, but this is because the unit is using MOS for the image sensor. This is not a malfunction.

Power Problem Check points

This unit cannot be turned on.

This unit does not stay on long enough.

Battery runs down quickly.

Charge the battery again to ensure it is sufficiently charged. (l 16)

In cold places, the battery using time becomes shorter. The battery has a limited life. If the operating time is still too

short even after the battery is fully charged, the battery has worn out and needs to be replaced.

This unit cannot be operated though it is turned on.

This unit does not operate normally.

Remove the battery or AC adaptor, wait about 1 minute and then reconnect the battery or AC adaptor. Then about 1 minute later, turn on the unit again. (Conducting the above operation while the SD card is being accessed may damage the data on the media.)

If normal operation is still not restored, detach the power connected, and consult the dealer who you purchased this unit from.

ERROR OCCURRED. PLEASE TURN UNIT OFF, THEN TURN ON AGAIN. is displayed.

The unit has automatically detected an error. Restart the unit by turning off and on.

The unit will be turned off in about 1 minute if the unit is not turned off and on.

Repair is needed if it is repeatedly displayed even if it is restarted. Detach the power connected, and consult the dealer who you purchased this unit from. Do not attempt to repair the unit by yourself.

- 189 -

Indication Problem Check points

Function display (Remaining Display, Counter Display, etc.) is not displayed.

[CARD & BATTERY] or [OTHER DISPLAY] of the [DISP SETUP] is [OFF]. (l 174)

Press the COUNTER button to switch the counter display. (l 70)

Recording Problem Check points

The unit arbitrarily stops recording.

Use an SD card that can be used for motion picture recording. (l 21)

The recordable time may have shortened due to the deterioration of the data writing speed or repeated recording and deletion. Using the unit, format the SD card. (l 32)

Auto Focus function does not work.

If you are trying to record a scene which is hard to bring into focus in Auto Focus Mode, use the Manual Focus Mode to adjust the focus. (l 37, 44)

Audio is not recorded. Variable Frame Rate Mode or Interval Recording is enabled. (l 91, 162)

is displayed and audio is not recorded in Variable Frame Rate Mode.

Audio is not recorded for Interval Recording.

Color or brightness of the image changes, or you may see horizontal bars in the image.

The LCD monitor flickers indoors.

Color or brightness of the image may change, or you may see horizontal bars in the image when the object is recorded under fluorescent light, mercury light or sodium light, etc., but this is not a malfunction.

Record images in Auto Shutter Mode or adjust the shutter speed to 1/50, 1/60 or 1/100.

Adjust the Synchro Scan shutter speed. (l 65)

A.REC

- 190 -

Playback Problem Check points

Scenes/still pictures cannot be played back.

Any scenes/still pictures where the thumbnails are displayed as cannot be played back.

In most cases, is displayed for the following scenes: j Scenes recorded with another device or edited with editing

software j Scenes with damaged data

Scenes/still pictures cannot be deleted.

Release the protect setting. (l 110) Any scenes/still pictures where the thumbnails are displayed

as cannot be deleted. If the scenes/still pictures are unnecessary, format the SD card to erase the data. (l 32) Please be aware that if a SD card is formatted then all the data recorded on the SD card is erased and cannot be recovered. Back up important data on a PC etc.

With other products Problem Check points

Although this unit is correctly connected to an external monitor, images cannot be seen.

The images are squeezed horizontally.

Please read the operating instructions of your external monitor and select the channel that matches the input used for the connection.

Change the setting of the unit depending on the cable connecting to the external monitor. (l 115)

Even when this unit is connected to the external monitor by the HDMI cable, images or sounds are not output.

Check if the HDMI cable is connected correctly. Insert the HDMI cable all the way in.

If the SD card is inserted in another device, it is not recognized.

Check that the device is compatible with the capacity or type of SD card (SDHC Memory Card/SDXC Memory Card) that you inserted. Refer to the operating instructions of the device for details.

When connected by the USB Cable, this unit is not detected by the other devices.

When connected to other devices using only the battery, reconnect using the AC adaptor.

- 191 -

If AVCHD scenes do not change smoothly when played back on another device

The images may be still for several seconds at the joins between the scenes if the following operations are performed when multiple scenes have been continuously played back using another device. Just how smoothly the scenes will be played back depends on the playback device. Depending

on the device used, the images may stop moving and become still for a moment even when none of the following conditions are applicable.

A continuous recording of motion picture data that exceeds 4 GB may momentarily stop at every 4 GB of data when played back with another device.

With a PC Problem Check points

When connected by the USB Cable, this unit is not detected by the PC.

After re-inserting the SD card into the unit, reconnect the USB Cable.

Select another USB terminal on the PC. Check the operating environment. (l 121) Connect the USB Cable again after restarting the PC and

turning on this unit again.

When the USB Cable is disconnected, an error message will appear on the PC.

To disconnect the USB Cable safely, double-click the icon in the task tray and follow the instructions on the screen.

Others Problem Check points

If the SD card is inserted in this unit, it is not recognized.

If the SD card is formatted on a PC, it may not be recognized by this unit. Use this unit to format SD cards. (l 32)

Principal reasons for not playing back smoothly

The recording format [PS] was switched to another recording format when a scene was recorded

When the scenes were recorded on different dates

When scenes lasting under 3 seconds have been recorded

When PRE-REC was used for recording

When the Interval Recording is used

When deleting scenes

When scenes recorded more than 99 scenes on the same date

- 192 -

About recovery If faulty management information is found, the messages may appear and a repair is performed. (Repairing may take time depending on the error.) is displayed when abnormal management information is detected when the scenes are

displayed in thumbnail.

Use a sufficiently charged battery or the AC adaptor. Depending on the condition of the data, it may not be possible to completely repair the data. If recovery fails, it will not be possible to play back scenes recorded before the unit turned off. When data recorded on another device is recovered, it may not be possible to play back the data

on this unit or the other device. If recovery fails, turn the unit off and on again after waiting awhile. If recovery fails repeatedly,

format a media on the unit. Please be aware that if a media is formatted, then all the data recorded on the media will be erased.

If the thumbnail information is recovered, displaying the thumbnails may become slower.

There are two ways to update the firmware: 1 Use the dedicated tool P2_Status_Logger to check and apply the update.

Only customers registered as members to PASS (P2 Asset Support System) can log in to PASS to use the dedicated (P2_Status_Logger) tool. With P2_Status_Logger, you can check the version information of the device used and jump to the page to download the required firmware. For details about downloading and using P2_Status_Logger, refer to the pages displayed after logging in to PASS. Other benefits are offered to registered users. For details, refer to the website (http://panasonic.biz/sav/pass_e) of PASS (P2 Asset Support System).

2 Check the version using the camera and apply the update. Check the version of the camera in the main menu # [MAINTENANCE] # [VERSION], access the latest information on the firmware from the website described below, and then download the firmware as needed.

Update completes by loading the downloaded files to the camera via the SD card. For details on update, visit the support desk at the following website: http://pro-av.panasonic.net

Others

Updating the firmware incorporated into the unit

- 193 -

Keep this unit as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.). If you use this unit on top of or near a TV, the

pictures and/or sound on this unit may be disrupted by electromagnetic wave radiation.

Do not use this unit near cell phones because doing so may result in noise adversely affecting the pictures and/or sound.

Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields created by speakers or large motors.

Electromagnetic wave radiation generated by microprocessors may adversely affect this unit, disturbing the pictures and/or sound.

If this unit is adversely affected by electromagnetic equipment and stops functioning properly, turn this unit off and remove the battery or disconnect AC adaptor. Then reinsert the battery or reconnect AC adaptor and turn this unit on.

Do not use this unit near radio transmitters or high-voltage lines. If you record near radio transmitters or

high-voltage lines, the recorded pictures and/ or sound may be adversely affected.

Make sure to use the supplied cords and cables. If you use optional accessories, use the cords and the cables supplied with them. Do not extend the cords and the cables.

Do not spray insecticides or volatile chemicals onto the unit. If the unit is sprayed with such chemicals, its

body may be marred and the surface finish may peel off.

Do not leave rubber or plastic products in contact with the unit for a long time.

When you use the unit in a sandy or dusty place such as a beach, do not let sand or fine dust get into the body and terminals of the unit. Also, keep the unit away from sea water. Sand or dust may damage the unit. (Care

should be taken when inserting and removing a card.)

If sea water splashes onto the unit, wipe off the water with a well wrung cloth. Then wipe the unit again with a dry cloth.

When carrying the unit, do not drop or bump it. A strong impact can break the units casing,

causing it to malfunction. When carrying this unit, please hold the hand

strap or shoulder strap firmly and treat it with care.

Cleaning Before cleaning, detach the battery or pull the

AC cable from the AC outlet, and then wipe the unit with a soft, dry cloth.

If the unit is very dirty, dip a cloth in water and squeeze firmly, and then wipe the unit with the damp cloth. Next, dry the unit with a dry cloth.

Use of benzine, paint thinner, alcohol, or dishwashing liquid may alter the camera body or peel the surface finish. Do not use these solvents.

When using a chemical dust cloth, follow the instructions that came with the cloth.

When you are not going to use the unit for an extended time When storing the unit, it is recommended that

you place a desiccant (silica gel) in with it.

Others

Cautions for use About this unit

The unit and the SD card become warm during use. This is not a malfunction.

- 194 -

Do not lift up this unit by the handle with the tripod still attached When the tripod is attached, its weight will

also affect the units handle, possibly causing the handle to break and hurting the user.

To carry the unit while the tripod is attached, take hold of the tripod.

Do not swing the unit around, shake it by, or allow it hang from the handle Do not jar, swing, or shake the unit by its

handle. Any strong jolt to the handle may damage the unit or result in personal injury.

Do not allow the cord to drag on the ground or pull a connected cord along the passage The cord will be damaged, causing fire or

electrical shock, when the cord gets caught by the feet, excite will also cause personal injury.

When this unit is turned on, do not use it in direct contact with the skin for a long period of time. When using this unit for a long period of time,

use a support such as a tripod. Low temperature burns may result if any high temperature part of this unit or hot air from the ventilation openings on the front side of the hand strap of this unit is in direct contact with the skin for a long period of time.

The battery used in this unit is a rechargeable lithium-ion battery. It is susceptible to humidity and temperature and the effect increases the more the temperature rises or falls. In cold areas, the full charge indication may not appear or the low battery indication may appear about 5 minutes after starting use. At high temperatures, the protection function may be triggered, making it impossible to use the unit.

Be sure to detach the battery after use. If the battery is left attached, a minute amount

of current continues to flow even if the unit is off. Keeping the unit in this state may result in over discharge of the battery. This may result in you not being able to use the battery even after it is charged.

The battery should be stored in the vinyl bag so metal does not come into contact with the terminals.

The battery should be stored in a cool place free from humidity, with as constant temperature as possible. (Recommended temperature: 15 oC to 25 oC (59 oF to 77 oF), Recommended humidity: 40%RH to 60%RH)

Extremely high temperatures or low temperatures will shorten the life of the battery.

If the battery is kept in high-temperature, high-humidity, or oily-smoky places, the terminals may rust and cause malfunctions.

To store the battery for a long period of time, we recommend you charge it once every year and store it again after you have completely used up the charged capacity.

Dust and other matter attached to the battery terminals should be removed.

Prepare spare batteries when going out for recording. Prepare batteries enough to last for 3 to 4

times the period you are planning to record for. Cold places such as a ski resort can shorten recording time.

If you drop the battery accidentally, check to see if the terminals are damaged. When this unit or battery charger is attached

with the terminal part in a deformed state, this unit or battery charger may be damaged.

Do not throw old battery into fire. Heating a battery or throwing it into a fire may

result in an explosion.

If the operating time is very short even after the battery has been recharged, the battery has worn out. Please purchase a new battery.

About the battery

- 195 -

If the temperature of the battery is extremely high or extremely low, charging may take time or the battery may not be charged.

If the charging lamp keeps flashing, make sure that the terminals of the battery or the battery charger are not exposed to dirt, foreign objects or dust, then reconnect them properly. Disconnect the AC cable from the AC outlet when you remove dirt, foreign objects or dust on the terminals of the battery or the battery charger. If the charging lamp is still flashing, the temperature of the battery may be extremely high or extremely low or something may be wrong with the battery or battery charger. Contact your dealer.

If you use the AC adaptor or battery charger near a radio, radio reception may be disturbed. Keep the AC adaptor or battery charger 1 m (3.3 feet) or more away from the radio.

When using the AC adaptor or battery charger, it may generate whirring sounds. However, this is normal.

After use, be sure to disconnect the AC cable from the AC outlet. (If you leave this unit connected, the AC adaptor will consume approximately 0.3 W and the battery charger approximately 0.3 W of current.)

Always keep the electrodes of the AC adaptor, battery charger and battery clean.

Install the device near an AC outlet so that the power disconnection device (AC mains plug) can be accessed easily by hand.

When disposing of or giving away the SD card, note that: Formatting and deletion of this unit or

computer only changes the file management information and does not completely delete the data in the SD card.

It is recommended that the main SD card is either physically destroyed or the SD card is physically formatted using this unit when disposing of or giving away the SD card.

To physically format, connect this unit to the AC adaptor, select [OTHER FUNCTION] # [FORMAT MEDIA] # [SD CARD 1] or [SD CARD 2] from the menu, and touch [YES]. Press and hold recording start/stop button in the following screen for three seconds. Screen to delete the SD card data is displayed, so select [YES] and follow the instruction on the screen.

The customer is responsible for the management of the data in the SD card.

About the AC adaptor/battery charger

About the SD card

- 196 -

When the LCD screen is dirty or condensation has occurred, please wipe it using a soft cloth such as a lens cloth.

Do not touch the LCD monitor with your finger nails, or rub or press with strong force.

It may become hard to see or hard to recognize the touch when the LCD protection sheet is affixed.

When the unit has become very cold, for example due to storage in a cold area, its LCD monitor will be slightly darker than usual immediately after the unit is turned on. The normal brightness will be restored when the units internal temperature rises.

LCD monitor/viewfinder

Extremely high precision technology is employed to produce the LCD Monitor screen. The result is more than 99.99% effective dots with a mere 0.01% of the dots inactive or always lit. However, this is not a malfunction and does not affect the recorded picture.

Extremely high precision technology is employed to produce the viewfinder screen. The result is more than 99.99% effective dots with a mere 0.01% of the dots inactive or always lit. However, this is not a malfunction and does not affect the recorded picture.

- 197 -

Carefully observe copyright laws

Licenses SDXC Logo is a trademark of SD-3C, LLC. AVCHD, AVCHD Progressive and the

AVCHD Progressive logo are trademarks of Panasonic Corporation and Sony Corporation.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

LEICA is a registered trademark of Leica Microsystems IR GmbH.

DICOMAR is a registered trademark of Leica Camera AG.

Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.

Intel, Pentium, Celeron and IntelCore are trademarks of Intel Corporation in the U.S. and/or other countries.

Mac and OS X are trademarks of Apple Inc. registered in the U.S. and other countries.

Other names of systems and products mentioned in these instructions are usually the registered trademarks or trademarks of the manufacturers who developed the system or product concerned.

This product is licensed under the AVC Patent Portfolio License for the personal use of a consumer or other uses in which it does not receive remuneration to (i) encode video in compliance with the AVC Standard (AVC Video) and/or (ii) decode AVC Video that was encoded by a consumer engaged in a personal activity and/or was obtained from a video provider licensed to provide AVC Video. No license is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA, L.L.C. See http://www.mpegla.com Separate license contracts must be obtained

from MPEG LA where SD Memory Cards containing information recorded with this product are to be distributed to end users for commercial purposes. End user refers to persons or organizations handling such contents for personal use.

This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.

Others

About copyright

IMPORTANT Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws.

- 198 -

Due to the specifications of this unit, depending on the recording function being used, it is not possible to use or select certain other recording functions. : Available; s: Not available* * Not available includes instances where the desired function cannot be used or selected.

Others

Recording functions that cannot be used simultaneously

Recording function to be

set

Currently set recording function

Interval Rec VFR Mode Relay recording

Simultaneous recording

Background recording

Dual codec recording

Interval Rec (l 162) s

VFR Mode (l 91, 131)

Relay recording (l 159) s s

Simultaneous recording (l 160)

Background recording (l 160) s s

Dual codec recording

(l 160, 161) s s

PRE-REC (l 86, 163) s s s

Capture (l 83) s s

Black Fade (l 78) s s

White Fade (l 78) s s

Time Stamp (l 164) s s

Recording Check (l 80) s s s

Last Scene Delete (l 80) s s s s

- 199 -

SD cards are only mentioned with their main memory size. The stated times are the approximate recordable times for continuous recording.

h is an abbreviation for hour, min for minute and s for second. If recording for long periods, prepare batteries for 3 or 4 times the period you wish to record for.

(l 18) When the default setting for [SYSTEM FREQ] is [59.94Hz]:

The default setting for [REC MODE] is [MP4], and the default setting for [REC FORMAT] is [UHD 2160/59.94p 150M]. When the default setting for [SYSTEM FREQ] is [50.00Hz]: The default setting for [REC MODE] is [MP4], and the default setting for [REC FORMAT] is [UHD 2160/50.00p 150M].

Maximum continuously recordable time for one scene: 10 hours The recording is paused once when the recording time for one scene exceeds 10 hours, and the

recording will automatically resume after a few seconds. For information on the maximum continuous recordable time for one scene in Variable Frame

Rate Mode, refer to page 93. The recordable time may be reduced if recording with a lot of action is recorded or recording of

short scene is repeated. The recordable times depends on the recording condition or card type to be recorded. For information on picture sizes, frame rates, and bit rates in [REC FORMAT], refer to page 142.

When [REC MODE] is set to [MOV] or [MP4]

Others

Recording modes/approximate recordable time

Recording format System frequency setting (l 141)

SD card

4 GB 16 GB 64 GB

[4K 2160/24.00p 100M] [59.94Hz]/ [50.00Hz] s 20 min 1 h 20 min

[UHD 2160/59.94p 150M]

[59.94Hz]

s s 55 min

[UHD 2160/29.97p 100M] s 20 min 1 h 20 min

[UHD 2160/23.98p 100M]

[FHD 1080/59.94p ] s

10 min 40 min

[FHD 1080/59.94p 100M] 20 min 1 h 20 min

[FHD 1080/59.94p 50M] 10 min 40 min 2 h 40 min

[FHD 1080/29.97p ] s 10 min 40 min

[FHD 1080/23.98p ]

[FHD 1080/29.97p 50M]

10 min 40 min 2 h 40 min[FHD 1080/23.98p 50M]

[FHD 1080/59.94i 50M]

- 200 -

When [REC MODE] is set to [AVCHD]

Recording format System frequency setting (l 141)

SD card

4 GB 16 GB 64 GB

[UHD 2160/50.00p 150M]

[50.00Hz]

s s 55 min

[UHD 2160/25.00p 100M] s 20 min 1 h 20 min

[FHD 1080/50.00p ] s 10 min 40 min

[FHD 1080/50.00p 100M] s 20 min 1 h 20 min

[FHD 1080/50.00p 50M] 10 min 40 min 2 h 40 min

[FHD 1080/25.00p ] s 10 min 40 min

[FHD 1080/25.00p 50M] 10 min 40 min 2 h 40 min

[FHD 1080/50.00i 50M]

Recording format System frequency setting (l 141)

SD card

4 GB 16 GB 64 GB

[PS 1080/59.94p]

[59.94Hz]

19 min 1 h 20 min 5 h 20 min

[PH 1080/59.94i] 21 min 1 h 30 min 6 h

[PH 1080/23.98p]

[HA 1080/59.94i] 30 min 2 h 8 h 30 min

[HE 1080/59.94i] 1 h 30 min 6 h 40 min 27 h 30 min

[PM 720/59.94p] 1 h 4 h 15 min 17 h 10 min

[SA 480/59.94i] 1 h 4 h 16 h 30 min

[PS 1080/50.00p]

[50.00Hz]

19 min 1 h 20 min 5 h 20 min

[PH 1080/50.00i] 21 min 1 h 30 min 6 h

[HA 1080/50.00i] 30 min 2 h 8 h 30 min

[HE 1080/50.00i] 1 h 30 min 6 h 40 min 27 h 30 min

[PM 720/50.00p] 1 h 4 h 15 min 17 h 10 min

[SA 576/50.00i] 1 h 4 h 16 h 30 min

- 201 -

SD cards are only mentioned with their main memory size. The stated number is the approximate number of recordable pictures.

Maximum number of recordable pictures that can be displayed is 9999. If the number of recordable pictures exceeds 9999, R 9999+ is displayed. The number will not change when the picture is taken until the number of recordable pictures is 9999 or less.

The number of recordable pictures depends on the recording condition or card type to be recorded.

The memory capacity indicated on the label of an SD card is the total of the capacity for copyright protection and management and the capacity which can be used on the unit, a PC etc.

Others

Approximate number of recordable pictures

Picture size Aspect ratio Memory Card

4 GB 16 GB 64 GB

4096k2160 17:9 700 2900 11500

3840k2160

16:9

750 3000 12000

1920k1080 3200 12500 52000

1280k720 7000 29000 118000

640k360 28000 117000 475000

640k

Manualsnet FAQs

If you want to find out how the AG-DVX200PJ Panasonic works, you can view and download the Panasonic AG-DVX200PJ, AG-DVX200PB Operating Instructions on the Manualsnet website.

Yes, we have the Operating Instructions for Panasonic AG-DVX200PJ as well as other Panasonic manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operating Instructions should include all the details that are needed to use a Panasonic AG-DVX200PJ. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Panasonic AG-DVX200PJ, AG-DVX200PB Operating Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Panasonic AG-DVX200PJ, AG-DVX200PB Operating Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Panasonic AG-DVX200PJ, AG-DVX200PB Operating Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Panasonic AG-DVX200PJ, AG-DVX200PB Operating Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Panasonic AG-DVX200PJ, AG-DVX200PB Operating Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.