Contents

Onkyo HT RC460 Instruction Manual PDF

1 of 140
1 of 140

Summary of Content for Onkyo HT RC460 Instruction Manual PDF

En

AV RECEIVER

HT-RC460

Instruction Manual

Contents

Safety Information and Introduction ............2

Table of Contents...........................................5

Connections .................................................11

Turning On & Basic Operations..................19

Advanced Operations ..................................43

Controlling Other Components...................66

Appendix.......................................................73

Internet Radio Guide

Remote Control Codes

En-2

Safety Information and Introduction

Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in

accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen

into the apparatus, C. If the apparatus has been exposed to rain or water,

D. If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in any way, and

F. When the apparatus exhibits a distinct change in performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Dont put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING RISK OF ELECTRIC SHOCK

DO NOT OPEN RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

AVIS PORTABLE CART WARNING

S3125A

Safety Information and Introduction

En-3

Precautions 1. Recording CopyrightUnless its for personal use

only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC FuseThe AC fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. CareOccasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Dont use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the units rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

For models with [POWER] button, or with both [POWER] and [ON/STANDBY] buttons: Pressing the [POWER] button to select OFF mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

For models with [ON/STANDBY] button only: Pressing the [ON/STANDBY] button to select Standby mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Preventing Hearing Loss Caution Excessive sound pressure from earphones and headphones can cause hearing loss.

6. Batteries and Heat Exposure Warning Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.

7. Never Touch this Unit with Wet HandsNever handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

8. Handling Notes If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case.

This units top and rear panels may get warm after prolonged use. This is normal.

If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models FCC Information for User CAUTION: The user changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and

receiver. Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician

for help.

For Canadian Models NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modle pour les Canadien REMARQUE: CET APPAREIL NUMRIQUE DE LA CLASSE B EST CONFORME LA NORME NMB-003 DU CANADA. Sur les modles dont la fiche est polarise:

ATTENTION: POUR VITER LES CHOCS LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.

Safety Information and Introduction

En-4

Supplied Accessories Make sure you have the following accessories:

* In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operations are the same regardless of color.

Installing the batteries

Note

If the remote controller doesnt work reliably, try replacing the batteries.

Dont mix new and old batteries or different types of batteries. If you intend not to use the remote controller for a long time,

remove the batteries to prevent damage from leakage or corrosion.

Remove expired batteries as soon as possible to prevent damage from leakage or corrosion.

Aiming the remote controller To use the remote controller, point it at the AV receivers remote control sensor, as shown below.

Indoor FM antenna ( page 18)

AM loop antenna ( page 18)

Speaker cable labels ( page 12)

Speaker setup microphone ( page 33)

Remote controller (RC-834M) and two batteries (AA/R6)

Quick Start Guide

Batteries (AA/R6)

Remote control sensor

AV receiver

Approx. 16 ft. (5 m)

Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.

Safety Information and Introduction

En-5

Table of Contents

Safety Information and Introduction

Important Safety Instructions ......................................2 Precautions ...................................................................3 Supplied Accessories...................................................4 Table of Contents..........................................................5 Features.........................................................................6 Front & Rear Panels......................................................7

Front Panel..................................................................7 Display ........................................................................8 Rear Panel ..................................................................9

Remote Controller.......................................................10 Controlling the AV Receiver ......................................10

Connections

Connecting the AV Receiver......................................11 Connecting Your Speakers .......................................11 About AV Connections ..............................................14 Connecting Components with HDMI .........................15 Connecting Your Components ..................................16 Connecting Onkyo RI Components...........................17 Connecting the Antennas..........................................18 Connecting the Power Cord ......................................18

Turning On & Basic Operations

Turning On/Off the AV Receiver ................................19 Turning On ................................................................19 Turning Off ................................................................19

Initial Setup..................................................................20 Selecting the Language

for the Onscreen Setup Menus...............................20 Audyssey 2EQ: Auto Setup.......................................20 Source Connection....................................................21 Remote Mode Setup .................................................21 Network Connection..................................................21 Terminating the Initial Setup .....................................21

Playback ......................................................................22 Playing the Connected Component ..........................22 Controlling Contents of USB or Network Devices.....23 Understanding Icons on the Display .........................24 Playing an iPod/iPhone via USB...............................24 Playing a USB Device...............................................25 Listening to vTuner Internet Radio............................26 Registering Other Internet Radio ..............................27 Changing the Icon Layout

on the Network Service Screen..............................27 Playing Music Files on a Server ...............................28 Remote Playback......................................................29 Listening to AM/FM Radio ........................................30

Using Basic Functions...............................................32 Using the Automatic Speaker Setup.........................32 Using the Listening Modes .......................................35 Using the Home Menu ..............................................40 Using the Sleep Timer ..............................................41 Setting the Display Brightness..................................41 Displaying Source Information..................................41 Changing the Input Display.......................................41 Using the Music Optimizer........................................42 Muting the AV Receiver ............................................42 Using Headphones ...................................................42

Advanced Operations

On-screen Setup.........................................................43 Using the Quick Setup ..............................................43 Using the Audio Settings of Quick Setup..................44 Using the Setup Menu (HOME) ................................46 About the HYBRID STANDBY indicator ...................47 Setup menu items.....................................................47 Input/Output Assign ..................................................48 Speaker Setup ..........................................................50 Audio Adjust..............................................................52 Source Setup ............................................................53 Listening Mode Preset ..............................................58 Miscellaneous ...........................................................59 Hardware Setup........................................................59 Remote Controller Setup ..........................................63 Lock Setup................................................................63

Zone 2 ..........................................................................64 Making Zone 2 Connections .....................................64 Controlling Zone 2 Components ...............................65

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock .................... 66 Using the Onkyo Dock.............................................. 66 Controlling Your iPod/iPhone ................................... 67

Controlling Other Components................................. 68 Preprogrammed Remote Control Codes .................. 68 Looking up for Remote Control Codes ..................... 68 Entering Remote Control Codes............................... 69 Remapping Colored Buttons .................................... 69 Remote Control Codes

for Onkyo Components Connected via RI ............. 70 Resetting the REMOTE MODE Buttons ................... 70 Resetting the Remote Controller .............................. 70 Controlling Other Components ................................. 70

Appendix

Troubleshooting ......................................................... 73 Firmware Update ........................................................ 79 Connection Tips and Video Signal Path .................. 83 Using an RIHD-compatible TV, Player,

or Recorder .............................................................. 86 About HDMI................................................................. 88 Network/USB Features............................................... 89 License and Trademark Information ........................ 92 Specifications ............................................................. 93

To reset the AV receiver to its factory defaults, turn it on and, while holding down CBL/SAT, press 8ON/STANDBY ( page 73).

Safety Information and Introduction

En-6

Features Amplifier

80 Watts/Channel @ 8 ohms (FTC) Optimum Gain Volume Circuitry H.C.P.S. (High Current Power Supply) Massive High

Power Transformer

Processing

Incorporates Qdeo technology for HDMI Video Upscaling (to 4K Compatible)

HDMI (Audio Return Channel, 3D, DeepColor, x.v.Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multi-CH PCM)

Dolby Pro Logic IIz Non-Scaling Configuration A-Form Listening Mode Memory Direct Mode Music Optimizer for Compressed Digital Music files 192 kHz/24-bit D/A Converters Powerful and Highly Accurate 32-bit Processing DSP Jitter Cleaning Circuit Technology

Connections

8 HDMI Inputs (1 on front panel) and 2 Outputs

Onkyo p for System Control 4 Digital Inputs (2 Optical/2 Coaxial) Component Video Switching (1 Input/1 Output) Banana Plug-Compatible Speaker Posts Powered Zone 2 Bi-Amping Capability for FL/FR with SBL/SBR Internet Radio Connectivity Network Capability for Streaming Audio Files 2 USB Inputs (Front/Rear) for Memory Devices and

iPod/iPhone models (Enables Display of Album Artwork) * Only the front-panel USB input is compatible with

iPod/iPhone.

MHL-Enabled AUX Front Input

Miscellaneous

40 FM/AM Presets Audyssey 2EQ to correct room acoustic problems Audyssey Dynamic EQ for loudness correction Audyssey Dynamic Volume to maintain optimal

listening level and dynamic range Crossover Adjustment

(40/50/60/70/80/90/100/120/150/200 Hz) A/V Sync Control Function (up to 800 ms) Auto Standby Function On-Screen Display via HDMI

Preprogrammed u-Compatible Remote

Safety Information and Introduction

En-7

Front & Rear Panels

For detailed information, see the pages in parentheses.

a 8ON/STANDBY button (19)

b ZONE 2, OFF buttons (65)

c Remote control sensor (4)

d Display (8)

e LISTENING MODE buttons (35)

f DIMMER button (41)

g MEMORY button (31)

h TUNING MODE button (30)

i DISPLAY button (41)

j SETUP button (46)

k TUNING q/w (30), PRESET e/r (31), cursor and ENTER buttons

l RETURN button

m MASTER VOLUME control (22)

n MUSIC OPTIMIZER button and indicator (42, 45)

o PHONES jack (42)

p AUX INPUT HDMI/MHL jack (15)

q TONE and Tone Level buttons (44)

r Input selector buttons (22)

s VIDEO jack (16)

t USB port (16)

u SETUP MIC jack (33)

v HYBRID STANDBY indicator (47)

Front Panel

a c e d f g h i j k l m b

r t o q p n s u v

Safety Information and Introduction

En-8

s

For detailed information, see the pages in parentheses.

a Z2 (Zone 2) indicator (65)

b 3D indicator This lights when a 3D input signal is detected.

c Headphone indicator (42)

d 1, 3 and cursor indicators (24)

e Listening mode and format indicators (35)

f Audyssey indicator (32, 53)

Dynamic EQ indicator (54)

Dynamic Vol indicator (54)

g M.Opt indicator (42, 45)

h Tuning indicators

AUTO indicator (30) TUNED indicator (30)

FM STEREO indicator (30)

i MUTING indicator (42)

j Input indicators (84)

HDMI indicator (60)

DIGITAL indicator

k ARC indicator (61)

l USB indicator (24, 25)

m NET indicator (26 to 29, 62)

n Message area

o SLEEP indicator (41)

p Channel/Unit indicators

ch indicator

Hz indicator m/ft indicator

dB indicator

q ASb indicator (61)

Display

j d n o qk m pj l

d c e hgfa b i

Safety Information and Introduction

En-9

a DIGITAL IN COAXIAL and OPTICAL jacks

b COMPONENT VIDEO IN and OUT jacks

c USB port

d ETHERNET port

e FM ANTENNA jack and AM ANTENNA terminal

f HDMI IN and HDMI output (HDMI OUT MAIN and HDMI OUT SUB) jacks

g SPEAKERS terminals

(CENTER, FRONT, SURROUND, SURROUND BACK or FRONT HIGH, ZONE 2)

h Power cord

i u REMOTE CONTROL jack

j Composite video and analog audio jacks

(BD/DVD IN, CBL/SAT IN, GAME IN, PC IN, TV/CD IN)

k ZONE 2 LINE OUT jacks

l SUBWOOFER PRE OUT jacks

m MONITOR OUT V jack

Rear Panel

a e b d c f h g

i j m k l

See Connecting the AV Receiver for connection ( pages 11 to 18).

Safety Information and Introduction

En-10

Remote Controller

For detailed information, see the pages in parentheses.

a 8 RECEIVER button (19)

b REMOTE MODE/INPUT SELECTOR buttons (22)

c q/w/e/r and ENTER buttons

d Q SETUP button (43)

e Listening Mode buttons (35)

f DIMMER button (41)

g MUTING button (42)

h DISPLAY button (41)

i VOL q/w button (22)

j RETURN button

k HOME button (40)

l SLEEP button (41)

Controlling the tuner To control the AV receivers tuner, press AM or FM (or RECEIVER).

a q/w buttons (30)

b D.TUN button (30)

c DISPLAY button

d CH +/ button (31)

e Number buttons (30)

*1 To control a component, you must first enter the remote control code. See Entering Remote Control Codes for more details ( page 69).

Controlling the AV Receiver

a

i

j

k

d

lbf

d

ac

b

g

hc

e

e

*1

To control the AV receiver, press RECEIVER to select Receiver mode. You can also use the remote controller to control Onkyo Blu-ray Disc/DVD player, CD player, and other components. See Entering Remote Control Codes for more details ( page 69).

En-11

Connections

Connecting the AV Receiver

Speaker Configuration

The following table indicates the channels you should use depending on the number of speakers that you have. No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings automatically ( page 32) or manually ( page 50).

*1 If youre using only one surround back speaker, connect it to the SURROUND BACK or FRONT HIGH L terminals.

*2 Front high and surround back speakers cannot be used at the same time.

Connecting the Speaker Cables

The following illustration shows how to connect the speakers to each pair of terminals. If youre using only one surround back speaker, connect it to the SURROUND BACK or FRONT HIGH L terminals.

Tip

You can specify whether surround back or front high speakers are connected in the Speaker Configuration menu ( page 50) or during Audyssey 2EQ Room Correction and Speaker Setup ( page 32).

Connecting Your Speakers

Number of speakers 2 3 4 5 6 7 7

Front speakers

Center speaker

Surround speakers

Surround back speaker*1*2

Surround back speakers*2

Front high speakers*2 Screw-type speaker terminals Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

Push-type speaker terminals Strip 3/8" to 1/2" (10 to 12 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

Banana Plugs If you are using banana plugs, tighten the speaker

terminal before inserting the banana plug. Do not insert the speaker code directly into the center

hole of the speaker terminal.

Center

Surround right

Front right

Surround left

Front leftSurround back/ Front high

left

Surround back/ Front high

right

1/2" to 5/8" (12 to 15 mm) 3/8" to 1/2"(10 to 12 mm)

Connections

En-12

Attaching the Speaker Cable Labels

The speaker terminals are color-coded for identification purpose.

The supplied speaker cable labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the table above. Then all you need to do is to match the color of each label to the corresponding speaker terminal.

Speaker Connection Precautions

Read the following before connecting your speakers: You can connect speakers with an impedance of between

6 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

Disconnect the power cord from the wall outlet before making any connections.

Read the instructions supplied with your speakers. Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals only to positive (+) terminals, and negative () terminals only to negative () terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.

Be careful not to short the positive and negative wires. Doing so may damage the AV receiver.

Make sure the metal core of the wire does not have contact with the AV receivers rear panel. Doing so may damage the AV receiver.

Dont connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.

Dont connect one speaker to several terminals.

Speaker Color

Front left, Front high left, Zone 2 left White

Front right, Front high right, Zone 2 right Red

Center Green

Surround left Blue

Surround right Gray

Surround back left Brown

Surround back right Tan

Connections

En-13

Using Powered Subwoofers

To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results. You can connect the powered subwoofer with two SUBWOOFER PRE OUT jacks respectively. The same signal is output from each jack.

Tip

If your subwoofer is unpowered and youre using an external amplifier, connect the subwoofer pre out jack to an input on the amplifier.

Bi-amping the Front Speakers

Bi-amping provides improved bass and treble performance. When bi-amping is used, the AV receiver is able to drive up to a 5.1 speaker system in the main room. Once youve completed the bi-amping connections as shown and turned on the AV receiver, you must set the speaker setting to enable bi-amping ( page 50).

LINE INPUT

LINE INPUT LINE INPUT

LINE INPUT

Powered subwoofer

Corner position

1/3 of wall position

Important: When making the bi-amping connections, be sure to remove

the jumper bars that link the speakers tweeter (high) and woofer (low) terminals.

Bi-amping can be used only with speakers that support bi- amping. Refer to your speaker manual.

Woofer (low)

Tweeter (high)

Front right Front left

Connections

En-14

Connecting AV components a

Before making any AV connections, read the manuals supplied with your AV components.

Dont connect the power cord until youve completed and double-checked all AV connections.

Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

To prevent interference, keep audio and video cables away from power cords and speaker cables.

AV Cables and Jacks

HDMI HDMI connections can carry digital video and audio.

Component video Component video separates the luminance (Y) and color difference signals (PB, PR), providing the best picture quality (some TV manufacturers label their component video sockets slightly differently).

Composite video Composite video is commonly used on TVs, DVDs, and other video equipment.

Optical digital audio Optical digital connections allow you to enjoy digital sound such as PCM*1, Dolby Digital or DTS. The audio quality is the same as coaxial.

Coaxial digital audio Coaxial digital connections allow you to enjoy digital sound such as PCM*1, Dolby Digital or DTS. The audio quality is the same as optical.

Analog audio (RCA) Analog audio connections (RCA) carry analog audio.

*1 For PCM signals, the supported sampling rates are 32/44.1/48/88.2/96 kHz. With HDMI connections, 176.4 and 192 kHz are also supported.

Note

The AV receiver does not support SCART plugs. The AV receivers optical digital jacks have shutter-type covers

that open when an optical plug is inserted and close when its removed. Push plugs in all the way.

Caution

To prevent shutter damage, hold the optical plug straight when inserting and removing.

About AV Connections

HDMI cable

Other cables

: Video & Audio

: Video

Game console Blu-ray Disc/ DVD player

TV, projector, etc.

AV receiver

TV, projector, etc.

AV receiver

Game console Blu-ray Disc/ DVD player

: Audio

Right!

Wrong!

Green

Blue

Red

Yellow

Orange

Y

PB

PR

White

Red

Connections

En-15

* If your TV doesnt support Audio Return Channel (ARC), you need to connect an optical digital cable together with the HDMI cable to the AV receiver.

* When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off.

Connect your components to the appropriate jacks. The default input assignments are shown below.

: Assignment can be changed ( page 48).

See also: Connection Tips and Video Signal Path ( page 83) Using an RIHD-compatible TV, Player, or Recorder

( page 86) About HDMI ( page 88)

Tip

To listen to the audio of a component connected via HDMI through your TVs speakers, enable HDMI Through ( page 60) and set the AV receiver to standby mode.

Note

In the case of Blu-ray Disc/DVD players, if no sound is output despite following the above-mentioned procedure, set your Blu- ray Disc/DVD players HDMI audio settings to PCM.

Audio Return Channel (ARC) function The Audio Return Channel (ARC) function enables an HDMI capable TV to send the audio stream to HDMI OUT MAIN on the AV receiver. This function can be used when:

Your TV is ARC capable, and The TV/CD input selector is selected, and HDMI Control(RIHD) is set to On( page 60), and Audio Return Channel is set to Auto ( page 61).

MHL (Mobile High-Definition Link) With its support for MHL (Mobile High-Definition Link), the AUX (Front) input allows you to deliver high- definition video from a connected mobile device.

Connecting Components with HDMI

Game console

TV, projector, etc.

Satellite/cable set-top box, etc.

Blu-ray Disc/DVD player

Personal computer

Camcorder, etc.

Jack Components

IN1 Blu-ray Disc/DVD player

IN2 Satellite/cable set-top box, etc.

IN3 Game console

IN4 Personal computer

IN5 Other components

IN6 Other components

IN7 Other components

Front Camcorder, etc.

OUT MAIN TV

OUT SUB Projector, etc.

Connections

En-16

Connect your components to the appropriate jacks. The default input assignments are shown below. See Connection Tips and Video Signal Path for more information ( page 83).

: Assignment can be changed ( page 49).

Note *1 When the USB input is selected, you can input video signals

from the VIDEO jack. Video signals input from VIDEO will be output from the MONITOR OUT and HDMI output jacks.

*2 Do not connect the AV receivers USB port to a USB port on your computer. Music on your computer cannot be played through the AV receiver in this way.

*3 Only the front-panel USB input is compatible with iPod/iPhone.

*4 Connect a turntable (MM) that has a phono preamp built-in. If your turntable (MM) doesnt have it, youll need a commercially available phono preamp. If your turntable has a moving coil (MC) type cartridge, youll need a commercially available MC head amp or MC transformer as well as a phono preamp. See your turntables manual for details.

With connection C, you can enjoy Dolby Digital and DTS. (To listen in Zone 2 as well, use C and F.)

With connection F, you can enjoy audio from external components while you are in Zone 2.

With connection F, if your Blu-ray Disc/DVD player has both the main stereo and multichannel outputs, be sure to connect the main stereo.

Connecting Your Components

BA

C FD EB

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receivers display when changing settings.

No. Jack/Port Components

A USB, VIDEO*1 iPod/iPhone (video playback)

B USB*2*3 iPod/iPhone, MP3 player, USB flash drive

C DIGITAL IN

OPTICAL 1 (GAME) Game consoles

OPTICAL 2 (TV/CD) TV, CD player

COAXIAL 1 (BD/DVD) Blu-ray Disc/DVD player

COAXIAL 2 (CBL/SAT) Satellite/cable set-top box, RI dock, etc.

D COMPONENT VIDEO

IN (CBL/SAT) Satellite/cable set-top box, RI dock, etc.

OUT TV, projector, etc.

E ETHERNET Router

F MONITOR OUT TV, projector, etc.

BD/DVD IN Blu-ray Disc/DVD player

CBL/SAT IN Satellite/cable set-top box, etc.

GAME IN Game console, RI dock

PC IN Personal computer

TV/CD IN TV, CD player, cassette tape deck, MD, CD-R, Turntable*4, RI dock

Connections

En-17

With u (Remote Interactive), you can use the following special functions:

System On/Auto Power On When you start playback on a component connected via u, while the AV receiver is on standby, the AV receiver will automatically turn on and select that component as the input source.

Direct Change When playback is started on a component connected via u, the AV receiver automatically selects that component as the input source.

Remote Control You can use the AV receivers remote controller to control your other u-capable Onkyo components, pointing the remote controller at the AV receivers remote control sensor instead of the component. You must enter the appropriate remote control code first ( page 70).

Note

Use only u cables for u connections. u cables are supplied with Onkyo components.

Some components have two u jacks. You can connect either one to the AV receiver. The other jack is for connecting additional u-capable components.

Connect only Onkyo components to u jacks. Connecting other manufacturers components may cause a malfunction.

Some components may not support all u functions. Refer to the manuals supplied with your Onkyo components.

While Zone 2 is on, the System On/Auto Power On and Direct Change u functions do not work.

Connecting Onkyo RI Components

1 Make sure that each Onkyo component is connected with an analog audio cable (connection F in the hookup examples) ( page 16).

2 Make the u connection (see the illustration).

3 If youre using an RI Dock, or cassette tape deck, change the Input Display ( page 41).

L R ANALOG

AUDIO OUT

L R ANALOG

AUDIO OUT

e.g., cassette tape deck

RI Dock

Connections

En-18

This section explains how to connect the supplied indoor FM antenna and AM loop antenna. The AV receiver wont pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

Note

Once your AV receiver is ready for use, youll need to tune into a radio station and position the antenna to achieve the best possible reception.

Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

Tip

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead. If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM

antenna.

Connecting the Antennas

Thumbtacks, etc.

Insert the plug fully into the jack.Push. Insert wire. Release.

Assembling the AM loop antenna

Indoor FM antenna (supplied)AM loop antenna (supplied)

Caution

Be careful not to injure yourself when using thumbtacks.

Note

Before connecting the power cord, connect all of your speakers and AV components.

Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.

Connecting the Power Cord

1 Plug the power cord into an AC wall outlet.

En-19

Turning On & Basic Operations

Turning On/Off the AV Receiver

Tip

The HYBRID STANDBY indicator may light depending on the status of settings ( page 47).

For details on power management settings, see Auto Standby ( page 61).

8RECEIVER

RECEIVER

8ON/STANDBY

Turning On

1 Press 8ON/STANDBY on the front panel. or

Press RECEIVER followed by 8RECEIVER on the remote controller. The AV receiver comes on and its display lights.

Turning Off

1 Press 8ON/STANDBY on the front panel. or

Press RECEIVER followed by 8RECEIVER on the remote controller. The AV receiver will enter standby mode. To prevent any loud surprises when you turn on the AV receiver, always turn down the volume before you turn it off.

Smooth Operation in a Few Easy Steps (Initial Setup)

To ensure smooth operation, heres a few easy steps to help you configure the AV receiver before you use it for the very first time. These settings only need to be made once. See Initial Setup for details ( page 20).

If the Firmware Update Available window appears.

When a new version of the firmware is available, the notification window Firmware Update Available pops up. This notification only appears when the AV receiver is connected to your home network ( page 89). To perform the firmware update, follow the instructions on screen.

Use q/w and ENTER on the AV receiver or remote controller to select one of the options.

Update Now: Starts the firmware update. Refer to Firmware Update ( page 79).

Remind me Later: The update notification will pop up again the next time you turn the AV receiver on.

Never Remind me: Disables the automatic update notification.

Tip

The update notification window can be enabled or disabled in Update Notice ( page 62).

Turning On & Basic Operations

En-20

Initial Setup This section explains the settings that we recommend you to make before using the AV receiver for the very first time. A setup wizard is launched upon first-time use to let you perform those settings.

This step determines the language used for the onscreen setup menus. See Language in OSD Setup ( page 59).

Tip

Pressing HOME will close the setup wizard. To restart the initial setup, select Initial Setup in the Hardware Setup menu ( page 62).

After selecting the language for on-screen setup menus, a welcome screen is displayed.

This step performs the automatic speaker setup.

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN.

Selecting the Language for the Onscreen Setup Menus

1 Use q/w on the AV receiver or remote controller to select one of the following options, and then press ENTER.

Yes: Continues to Audyssey 2EQ: Auto Setup.

No: Skips the settings and terminates the initial setup. The setup wizard goes to Terminating the Initial Setup. You can always restart the initial setup by selecting Initial Setup in the Hardware Setup menu ( page 62).

1st Step : Audyssey 2EQ: Auto Setup 2nd Step : Source Connection 3rd Step : Remote Mode Setup 4th Step : Network Connection

Yes No

Exit

Initial Setup

HOME

Welcome to initial setup. Have you connected all the speakers and devices? Before starting, please connect speakers and sources. Now, would you like to start initial setup?

Audyssey 2EQ: Auto Setup

1 Use q/w to select one of the following options, and then press ENTER.

Do it Now: The automatic speaker setup is performed following instructions on screen. Refer to step 2 of Using the Automatic Speaker Setup ( page 32). When this setting is complete, the setup wizard continues to Source Connection.

Do it Later: Skips this setting. Press ENTER and continue to Source Connection.

Turning On & Basic Operations

En-21

This step checks the connection of source components. With this step, you can enter remote control codes for the components you want to operate.

This step checks your network connection.

This step ends the initial setup process.

Source Connection

1 Use q/w to select one of the following options, and then press ENTER.

Yes, Continue: Performs the checkings.

No, Skip: Skips this step and continues to Remote Mode Setup.

2 Select the input selector for which you want to check the connection and press ENTER. The picture of the corresponding source should appear on screen with a verification prompt.

3 When prompted, use q/w to select one of the following options and then press ENTER.

Yes: Confirms that the source is properly displayed.

No: Displays an error report. Follow the troubleshooting instructions and recheck the source.

4 Use q/w to select one of the following options, and then press ENTER.

Yes: Returns to step 2.

No, Done Checking: The setup wizard continues to Remote Mode Setup.

Remote Mode Setup

1 Use q/w to select one of the following options, and then press ENTER.

Yes: Performs the remote control code input. Refer to step 5 of Looking up for Remote Control Codes ( page 68).

No, Skip: Skips this step and continues to Network Connection.

2 When youre finished, select one of the following options and press ENTER.

Yes, Done: The setup wizard continues to Network Connection.

No, not yet: You can enter other remote control codes.

Network Connection

1 Use q/w to select one of the following options, and then press ENTER.

Yes: Performs the checkings.

No, Skip: Skips this step and terminates the initial setup.

Note

If you use both wired and wireless network connections, the wireless will take priority. For further details, see the instruction manual provided with your wireless device.

2 Follow the instructions on screen to perform the network checking. The checking is complete when the message Successfully connected. appears at the middle of the screen. Press ENTER to terminate the initial setup.

3 If an error message appears, select one of the following options and press ENTER.

Retry: Performs the checking again.

No, Do it Later: Skips this step and terminates the initial setup. The setup wizard goes to Terminating the Initial Setup.

Terminating the Initial Setup

1 Press ENTER. To restart the initial setup, select Initial Setup in the Hardware Setup menu ( page 62).

Turning On & Basic Operations

En-22

Playback Operating with the remote controller

Operating on the AV receiver

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receivers display when changing settings.

This section describes the procedure for using the remote controller, unless otherwise specified.

Playing the Connected Component

1 Press RECEIVER followed by an INPUT SELECTOR button.

2 Start playback on the source component. See also: Playing an iPod/iPhone via USB ( page 24) Playing a USB Device ( page 25) Listening to vTuner Internet Radio ( page 26) Registering Other Internet Radio ( page 27) Playing Music Files on a Server ( page 28) Remote Playback ( page 29) Listening to AM/FM Radio ( page 30) iPod/iPhone Playback via Onkyo Dock

( page 66) Controlling Other Components ( page 68)

3 To adjust the volume, use VOL q/w.

4 Select a listening mode and enjoy! See also: Using the Listening Modes ( page 35)

RECEIVER

VOL q/w

INPUT SELECTOR

Listening mode buttons

1 Use the input selector buttons to select the input source.

2 Start playback on the source component.

3 To adjust the volume, use the MASTER VOLUME control.

4 Select a listening mode and enjoy!

Screen Saver If there is no video signal on the current input source and no operation for a specific time (three minutes by default), a screen saver automatically comes on.

Tip

The time until the screen saver activates itself can be changed in the Screen Saver setting ( page 59).

The screen will return to its previous state if the AV receiver is operated.

MASTER VOLUME LISTENING MODE

Input selector buttons

Turning On & Basic Operations

En-23

Tip

See Controlling Other Components about the operation of other components ( page 68).

Note

The buttons you can use will differ depending on the devices and media used for playback.

Controlling Contents of USB or Network Devices

d

k

j

m

b

a

c

f

g

l

n

o

q

h

i

p

e

Press USB or NET first.

a TOP MENU This button displays the top menu for each media or service.

b q/w and ENTER These buttons navigate through the menus.

e/r This button cycles through pages.

PLAYLIST e/r In Standard Mode (iPod/iPhone), this button selects playlists.

c 1 This button starts playback.

d 7 This button selects the beginning of the current song. Pressing this button twice selects the previous song.

e 5 This button fast-reverses the current song.

f 3 This button pauses playback.

g SEARCH You can toggle between the playback screen and the list screen during playback.

h DISPLAY This button switches between song information during playback. Press this button while the list screen is displayed to return to the playback screen.

i ALBUM +/ In Standard Mode (iPod/iPhone), this button selects albums.

j MENU This button displays the menu of Internet radio services.

k RETURN This button returns to the previous menu.

l 4 This button fast-forwards the current song.

m 6 This button selects the next song.

n 2 This button stops playback.

o MODE You can switch between Standard Mode and Extended Mode during iPod/iPhone playback.

p RANDOM This button performs random playback.

q REPEAT Press this button repeatedly to cycle through the repeat modes.

Turning On & Basic Operations

En-24

This section describes icons that appear on the AV receivers display during media playback.

This section explains how to play music/video files on the iPod/iPhone. Compatible iPod/iPhone models Made for: iPod touch (1st, 2nd, 3rd and 4th generation), iPod classic, iPod nano (2nd, 3rd, 4th, 5th and 6th generation), iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone

Note

While the message Connecting... appears on the AV receivers display, do not disconnect the USB cable supplied with your iPod/iPhone or the USB device from the USB port.

If you connect an iPod or iPhone to the USB port, no sound will be output from the headphones jack.

Understanding Icons on the Display

Icon Description

Folder

Track

Playback

Pause

Fast Forward

Fast Reverse

Artist

Album

Repeat One Track

Repeat Folder (USB Device)

Repeat

Shuffle

Shuffle Album (iPod/iPhone)

Playing an iPod/iPhone via USB

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN.

1 Press USB repeatedly to select the USB(Front) input.

Tip

The same operation can be done by selecting USB in the Home menu.

2 Connect the USB cable that comes with the iPod/iPhone to the USB port on the front of the AV receiver. While reading the contents of your iPod/iPhone, the message Connecting... appears on the AV receivers display. The USB indicator lights. It will flash if the AV receiver cannot read the iPod/iPhone.

Tip

When connecting your iPod/iPhone with a USB cable, we recommend you use an official USB cable from Apple Inc.

3 Press MODE repeatedly to switch to Extended Mode (Music) or Extended Mode (Video).

A list of your iPod/iPhone models contents appears.

Tip

If you want to operate using the iPod/iPhone or the remote controller, press MODE repeatedly to switch to Standard mode.

When you disconnect the iPod/iPhone, the AV receiver remembers the current mode. This means that if you disconnect when in Extended Mode (Music), the AV receiver will start in Extended Mode (Music) the next time you connect the iPod/iPhone.

4 Use q/w to select a folder, and then press ENTER to open it.

Tip

You can also use the q/w, ENTER and TUNING MODE buttons on the front panel. TUNING MODE allows you to switch modes.

5 Use q/w to select a music/video file, and press ENTER or 1 to start playback.

Turning On & Basic Operations

En-25

Extended Mode (Music) Control

The music content information is displayed (lists are displayed), and you can control the music content while looking at the screen. Top screen list: Playlists, Artists, Albums, Genres, Songs, Composers, Shuffle Songs, Now Playing.

Note

In this mode, video contents are not displayed, even if they are input from the VIDEO jack on the AV receivers front panel.

Extended Mode (Video) control

The video content information is displayed (lists are displayed), and you can control the video content while looking at the screen. Top screen list: Movies, Music Videos, TV Shows, Video Podcasts, Rentals.

Note

To view the video contents of your iPod/iPhone, connect it to the USB port and VIDEO jack on the AV receivers front panel, using the official Apple Composite AV Cable.

Depending on your iPod/iPhone model and generation, the displayed items may vary and the support for Extended Mode (Video) is not guaranteed.

Standard Mode Control

The content information is not displayed, but can be operated using the iPod/iPhone or the remote controller.

This section explains how to play music files from a USB device (e.g., USB flash drives and MP3 players). See also: Network/USB Features ( page 89).

Note

While the message Connecting... appears on the AV receivers display, do not disconnect the USB cable supplied with your iPod/iPhone or the USB device from the USB port.

Playing a USB Device

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN.

1 Press USB repeatedly to select the USB(Front) or USB(Rear) input.

2 Plug your USB device into the AV receivers USB port. The USB indicator lights. It will flash if the AV receiver cannot read the USB device.

3 Press ENTER. A list of the devices contents appears. To open a folder, use q/w to select it, and then press ENTER.

4 Use q/w to select a music file, and press ENTER or 1 to start playback.

Turning On & Basic Operations

En-26

The vTuner Internet Radio Service is a portal site featuring radio stations from all over the world. You can search for stations by categories such as genre or location. The AV receiver is preinstalled with this service.

Listening to vTuner Internet Radio

You need to connect the AV receiver to your home network ( page 89). The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN.

1 Press NET. The network service screen appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver.

Tip

The same operation can be done by selecting Network Service in the Home menu.

2 Use q/w/e/r to select vTuner Internet Radio and then press ENTER.

3 Use q/w to select a program and then press ENTER. Playback starts.

Tip

You can find stations similar to the one being played. During playback, press MENU on the remote controller, select Stations like this and press ENTER.

Great Artist

My Music

My Favorite

0 : 11

Adding vTuner Internet Radio Stations to Favorites

There are two ways you can register specific Internet radio stations (programs) from the vTuner Internet Radio.

Adding to My Favorites The selected program will be added to My Favorites on the network service screen, which appears when pressing NET on the remote controller.

1. Press MENU with the station selected or while a station is playing.

2. Use q/w to select Add to My Favorites, and press ENTER.

3. Use q/w/e/r to select OK, and press ENTER.

Adding to vTuner Internet Radios Favorites Select vTuner Internet Radio and press ENTER to display the Favorites folder that appears on the same screen as Stations By Genre, Stations By Location, etc. This is where your favorite Internet radio bookmarks will be stored. To register your favorite stations using a personal computer, you need to connect your PC to the same network as the AV receiver. Enter the ID# (MAC address) of your unit on the http://onkyo.vtuner.com/. You can then register your favorite radio programs. The ID# is shown at the bottom of the vTuner Internet Radio top menu, and the AV receivers MAC address is shown on Network of the Setup menu ( page 62).

Tip

You can rename the stations saved in My Favorites.

Turning On & Basic Operations

En-27

Internet radio URLs in the following formats are supported: PLS, M3U, and podcast (RSS). However, depending on the type of data or audio format used by the Internet radio station, you may not be able to listen to some stations. To listen to other Internet radio stations, you must register your station in My Favorites of the network service screen, as described below.

Note

Services available may vary depending on the region. See the separate instructions for more information.

Tip

If you want to add a new station directly from My Favorites, select an empty slot in the list and press MENU. Then, select Create New Station and press ENTER. Pressing ENTER again will display the keyboard screen. Use that keyboard to enter the stations name and URL respectively, and then press ENTER.

If you want to delete a station saved in My Favorites, press MENU with the station selected or while the station is playing. Then, use q/w to select Delete from My Favorites and press ENTER. You can also delete stations from the Web Setup.

If you want to rename a station, select the desired station and press MENU. Then, use q/w to select Rename this station and press ENTER.

You can save up to 40 Internet radio stations.

The layout of icons can be customized by switching their positions on the network service screen.

Registering Other Internet Radio

You need to connect the AV receiver to your home network ( page 89). The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN.

1 Select Network on the Setup menu to verify your IP address ( page 62). Take a note of the IP address.

2 On your computer, start your web browser.

3 Enter the AV receivers IP address in the browsers Internet address (URL) field. If you are using Internet Explorer, you can also enter the URL by selecting Open... on the File menu. Information on the AV receiver is then shown on your Internet browser (Web Setup).

4 Click on the My Favorites tab, and enter the Internet radio stations name and URL.

5 Click Save to save the Internet radio station. The Internet radio station is then added to My Favorites. To play the registered station, press NET, and then select My Favorites on the network service screen. A list of registered Internet radio stations appears. Select the one that you saved and press ENTER.

Changing the Icon Layout on the Network Service Screen

1 Press NET. The network service screen appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver.

Tip

The same operation can be done by selecting Network Service in the Home menu.

2 Press MODE/D (blue) on the remote controller.

3 Use q/w/e/r to select an icon to move, and then press ENTER.

4 Use q/w/e/r to select another icon as the destination, and then press ENTER. The icons switch positions and the message Completed! appears. If you press RETURN, the Custom Mode process will be cancelled or it will go back one step.

Turning On & Basic Operations

En-28

This section explains how to play music files on a computer or media server through the AV receiver (Server Playback).

Windows Media Player 11 Setup

This section explains how to configure Windows Media Player 11 so that the AV receiver can play the music files stored on your computer.

Playing Music Files on a Server

You need to connect the AV receiver to your home network ( page 89). The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN.

1 Start your computer or media server.

2 Press NET. The network service screen appears. The NET indicator lights. If it flashes, confirm the network connection.

Tip

The same operation can be done by selecting Network Service in the Home menu.

3 Use q/w/e/r to select DLNA, and press ENTER.

Tip

To go back to the previous screen, press RETURN.

4 Use q/w to select a server, and then press ENTER. The menu is displayed according to the server functions.

Note

The search function does not work with media servers which do not support this function.

Photos and movies stored on a media server cannot be accessed from the AV receiver.

Depending on the sharing settings in the media server, the AV receiver may not able to access the content. See the instruction manual of the media server.

5 Use q/w to select an item, and then press ENTER or 1 to start playback.

Note

Depending on the media server, 5/4/3 may not work.

If the message No Item. appears, this means that no information can be retrieved from the server. In this case, check your server, network, and AV receiver connections.

Artist name

My favorite song 1

My favorite album

0 : 11

1 Start Windows Media Player 11.

2 On the Library menu, select Media Sharing. The Media Sharing dialog box appears.

3 Select the Share my media check box, and then click OK. A list of the supported devices appears.

4 Select the AV receiver in the list, and then click Allow. The corresponding icon will be checked.

5 Click OK to close the dialog box. This completes the Windows Media Player 11 configuration. You can now play the music files in your Windows Media Player 11 library through the AV receiver.

Tip

Windows Media Player 11 can be downloaded for free from the Microsoft web site.

Turning On & Basic Operations

En-29

Remote Playback means you can play the music files stored on a media server or personal computer with the AV receiver by operating the controller device in the home network.

Windows Media Player 12 Setup

This section explains how to configure Windows Media Player 12 so that the AV receiver can play the music files stored on your personal computer.

Using Remote Playback

Note

Remote playback cannot be used in any of the following cases: Network services are being used. Contents are being played from a USB device or iPod/iPhone. Zones are turned on.

Remote Playback

You need to connect the AV receiver to your home network ( page 89). The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN.

1 Start Windows Media Player 12.

2 On the Stream menu, select Turn on media streaming. A dialog box appears.

Tip

If the media streaming is already activated, clicking on More streaming options... in the Stream menu will display a list of the playback devices connected to the network. You can skip step 3.

3 Move your cursor and click on Turn on media streaming. A list of media server appears. Wording may vary slightly depending on the network location.

4 On the Media streaming options, select the AV receiver and confirm that it is set to Allow.

5 Click OK to close the dialog box. This completes the Windows Media Player 12 configuration. You can now play the music files in your Windows Media Player 12 library.

Tip

On the Stream menu, confirm that Allow remote control of my Player... is checked.

1 Turn on the AV receiver.

2 Start Windows Media Player 12. To enable remote playback, you must first configure Windows Media Player 12.

3 On Windows Media Player 12, right-click on a music file. The right-click menu appears.

Tip

For selecting another media server, select the desired media server from the Other Libraries menu on Windows Media Player 12.

4 Select the AV receiver in Remote playback. The Play to window appears and playback on the AV receiver starts. Operations during remote playback can be made from the Play to window of Windows 7 on your personal computer. A playback screen will be displayed on the connected TV.

5 Adjusting the Volume. You can adjust the volume by adjusting the volume bar in the Remote playback window. The default maximum volume level is 64. If you wish to change this, enter the value from the Web Setup in your browser. Refer to step 3 of Registering Other Internet Radio for details ( page 27). The volume value of the remote window and the volume value of the AV receiver may not always match. Adjustments you make to the volume in the AV receiver will not be reflected in the Remote playback window.

Turning On & Basic Operations

En-30

Using the Tuner

With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. You can also change the frequency steps ( page 59).

Tuning into Radio Stations

Auto tuning mode

Manual tuning mode In manual tuning mode, FM stations will be in mono.

Tuning into stations by frequency You can tune into AM and FM stations directly by entering the appropriate frequency.

Listening to AM/FM Radio

This section describes the procedure of using the buttons on the front panel, unless otherwise specified.

1 Press AM or FM to select either AM or FM. In this example, FM has been selected.

(Actual display depends on the country.)

Band Frequency

1 Press TUNING MODE so that the AUTO indicator lights on the AV receivers display.

2 Press TUNING q/w. Searching stops when a station is found.

When tuned into a station, the TUNED indicator lights. When tuned into a stereo FM station, the FM STEREO indicator lights as shown.

Tip

Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to manual tuning mode and listen to the station in mono.

TUNED

FM STEREO

AUTO

1 Press TUNING MODE so that the AUTO indicator goes off on the AV receivers display.

2 Press and hold TUNING q/w. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time.

1 On the remote controller, press AM or FM to select AM or FM, followed by D.TUN.

(Actual display depends on the country.)

2 Within 8 seconds, use the number buttons to enter the frequency of the radio station. For example, to tune to 87.5 (FM), press 8, 7, 5 or 8, 7, 5, 0. If you have entered the wrong number, you can retry after 8 seconds.

Turning On & Basic Operations

En-31

Presetting AM/FM Stations

You can store a combination of up to 40 of your favorite AM/FM radio stations as presets.

Selecting Presets

Deleting Presets

1 Tune into the AM/FM station that you want to store as a preset. See the previous section.

2 Press MEMORY. The preset number flashes.

(Actual display depends on the country.)

3 While the preset number is flashing (about 8 seconds), use PRESET e/r to select a preset from 1 through 40.

4 Press MEMORY again to store the station or channel. The station or channel is stored and the preset number stops flashing. Repeat this procedure for all of your favorite AM/FM radio stations.

1 To select a preset, use PRESET e/r on the AV receiver, or the remote controllers CH +/.

Tip

You can also use the remote controllers number buttons to select a preset directly.

1 Select the preset that you want to delete. See the previous section.

2 While holding down MEMORY, press TUNING MODE. The preset is deleted and its number disappears from the AV receivers display.

Turning On & Basic Operations

En-32

Using Basic Functions

With the supplied calibrated microphone, Audyssey 2EQ automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyssey 2EQ then removes the distortion caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain. The result is clear, well-balanced sound for everyone. Audyssey 2EQ can be used with Audyssey Dynamic EQ and Audyssey Dynamic Volume ( page 54). Before using this function, connect and position all of your speakers. Audyssey 2EQ offers two ways of measuring: the Audyssey Quick Start and Audyssey 2EQ Full Calibration. Audyssey Quick Start uses the measurement from one

position to perform the speaker setting only. Audyssey 2EQ Full Calibration uses the

measurement from three positions to correct room response in addition to the speaker setting.

The more positions are used in measuring, the better the listening environment will become. We recommend using a measurement from three positions to create the best listening environment. The Quick Start takes 2 minutes and Full Calibration takes about 10 minutes. Total measurement time varies depending on the number of speakers.

Measurement procedure

To create a listening environment in your home theater that all listeners will enjoy, Audyssey 2EQ takes measurements at up to three positions within the listening area. Position the microphone at ear height of a seated listener with the microphone tip pointed directly at the ceiling using a tripod. Do not hold the microphone in your hand during measurements as this will produce inaccurate results.

a First measurement position Also referred to as the Main Listening Position, this refers to the most central position where one would normally sit within the listening environment. Audyssey 2EQ uses the measurements from this position to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer.

b Second measurement position The right side of the listening area.

c Third measurement position The left side of the listening area.

The distances from position a to b and a to c must be at least 1 meter (3.3 ft.).

Note

Make the room as quiet as possible. Background noise and Radio Frequency Interference (RFI) can disrupt the room measurements. Close windows, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices. Turn off the cell phone (even if it is not in use) or place it away from all audio electronics.

The microphone picks up test tones played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs.

Audyssey 2EQ Room Correction and Speaker Setup cannot be performed while a pair of headphones is connected.

Using the Automatic Speaker Setup

TV

abc

: Listening area a to c: Listening position

Turning On & Basic Operations

En-33

Note

You can cancel Audyssey 2EQ Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

Do not connect or disconnect any speakers during Audyssey 2EQ Room Correction and Speaker Setup.

If the AV receiver is muted, it will be unmuted automatically when Audyssey 2EQ Room Correction and Speaker Setup starts.

Changes to the room after Audyssey 2EQ Room Correction and Speaker Setup requires you run Audyssey 2EQ Room Correction and Speaker Setup again, as room EQ characteristics may have changed.

1 Turn on the AV receiver and the connected TV. On the TV, select the input to which the AV receiver is connected.

2 Set the speaker setup microphone at the Main Listening Position a, and connect it to the SETUP MIC jack.

The speaker setting menu appears.

Note

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receivers display when changing settings.

3 When youve finished making the settings, press ENTER.

Perform the Speaker Setup according to your speaker configuration:

Speakers Type (Front) ( page 50) Powered Zone 2 ( page 50) Surround Back/Front High ( page 50)

4 Use q/w to select Audyssey Quick Start or Audyssey 2EQ Full Calibration, and then press ENTER.

Speaker setup microphone

SETUP MIC jack

2EQ: Auto Setup AUDYSSEY

Speakers Type (Front) Powered Zone 2 Surround Back/Front High

Normal No

Surround Back

5 Press ENTER. Audyssey 2EQ Room Correction and Speaker Setup starts. Test tones are played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey 2EQ Room Correction and Speaker Setup, unless you want to cancel the setup. If you select Audyssey Quick Start, you will go to step 8.

6 Place the speaker setup microphone at the next position, and then press ENTER. Audyssey 2EQ performs more measurements. This takes a few minutes.

7 When prompted, repeat step 6.

8 Use q/w to select an option, and then press ENTER.

The options are: Save:

Save the calculated settings and exit Audyssey 2EQ Room Correction and Speaker Setup.

Cancel: Cancel Audyssey 2EQ Room Correction and Speaker Setup.

Save Cancel

AUDYSSEY 2EQ: Auto Setup

-- Review Speaker Configuration --

Subwoofer Front Center Surround Front High Surround Back Surround Back Ch

Yes 100Hz

40Hz 100Hz None

120Hz 2ch

Tip

You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by using e/r.

9 Use q/w to select a target, and use e/r to change the setting. After the results of Audyssey 2EQ have been saved, the menu will display the Audyssey ( page 53), Dynamic EQ ( page 54), Dynamic Volume ( page 54) settings.

Note

When Audyssey Quick Start has been used for measurement, Audyssey cannot be selected.

These settings are applied to all input selectors.

10 Press ENTER.

11 Disconnect the speaker setup microphone.

Turning On & Basic Operations

En-34

Error Messages

While Audyssey 2EQ Room Correction and Speaker Setup is in progress, one of the error messages below may appear.

The options are: Retry:

Try again. Cancel:

Cancel Audyssey 2EQ Room Correction and Speaker Setup.

Ambient noise is too high. The background noise is too loud. Remove the source of the noise and try again.

Speaker Matching Error! The number of speakers detected was different from that of the first measurement. Check the speaker connection.

Writing Error! This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, contact your Onkyo dealer.

Speaker Detect Error This message appears if a speaker is not detected. No means that no speaker was detected.

Tip

See Speaker Configuration for appropriate settings ( page 11).

Changing the Speaker Setup Manually

You can manually make changes to the settings found during Audyssey 2EQ Room Correction and Speaker Setup. See also: Speaker Configuration ( page 50) Speaker Distance ( page 51) Level Calibration ( page 51)

Using a Powered Subwoofer

If youre using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by Audyssey 2EQ Room Correction and Speaker Setup. If the Subwoofer appears on the Review Speaker Configuration screen as No, increase the subwoofers volume to the half-way point, set it to its highest crossover frequency, and then try running Audyssey 2EQ Room Correction and Speaker Setup again. Note that if the volume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. If the subwoofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofers instruction manual for details.

Retry Cancel

AUDYSSEY 2EQ: Auto Setup

Ambient noise is too high.

Error message

Turning On & Basic Operations

En-35

Selecting Listening Modes

See About Listening Modes for detailed information about the listening modes ( page 36).

Listening Mode Buttons

MOVIE/TV button This button selects the listening modes intended for use with movies and TV. MUSIC button This button selects the listening modes intended for use with music. GAME button This button selects the listening modes intended for use with video games. STEREO button This button selects the Stereo listening mode and All Channel Stereo listening mode.

Using the Listening Modes

GAME STEREO MOVIE/TV

MUSIC

Press RECEIVER first.

The Dolby Digital and DTS listening modes can only be selected if your Blu-ray Disc/DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI).

The listening modes you can select depends on the format of the input signal. To check the format, see Displaying Source Information ( page 41).

While a pair of headphones is connected, you can select the following listening modes: Mono, Direct, and Stereo.

MOVIE/TV, MUSIC, GAME

Turning On & Basic Operations

En-36

About Listening Modes

The AV receivers listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.

Explanatory Notes

ab Front speakers c Center speaker de Surround speakers f Subwoofer(s) gh Surround back speakers ij Front high speakers

Input Source The following audio formats are supported by the listening modes.

Speaker Layout The illustration shows which speakers are activated in each channel. See Speaker Configuration for the speaker setup ( page 50).

ij

gh

c b a f

de

A This is mono (monophonic) sound.

S This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two speakers.

D This is 5.1-channel surround sound. This surround system has five main channels of sound and a sixth subwoofer channel (called the point-one channel).

F This is 7.1-channel surround sound. This is a further sound enhancement to 5.1-channel sound with two additional speakers that provide greater sound envelopment and more accurate positioning of sounds.

G This is DTS-ES surround sound. This surround system can produce a discrete or a matrix-encoded sixth channel from existing DTS 5.1 encoded material.

H This is Dolby Digital EX surround sound. This provides a center back surround channel from 5.1- channel sources.

Z

X

C

N B

V

Turning On & Basic Operations

En-37

Onkyo-Original DSP Listening Modes

Listening Mode Description Input Source

Speaker Layout

Orchestra Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.

A S D F G H

CN

Unplugged Suitable for acoustic instruments, vocals and jazz, this mode emphasizes the front stereo image, giving the impression of being right in front of the stage.

Studio-Mix Suitable for rock or pop music, listening to music in this mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert.

TV Logic This mode adds realistic acoustics to TV shows produced in a TV studio, surround effects to the entire sound, and clarity to voices.

Game-RPG In this mode, the sound has a dramatic feel with a similar atmosphere to Orchestra mode.

Game-Action In this mode, sound localization is distinct with emphasis on bass.

Game-Rock In this mode, sound pressure is emphasized to heighten live feel.

Game-Sports In this mode, reverberation is increased and sound localization decreased slightly.

All Ch Stereo Ideal for background music, this mode fills the entire listening area with stereo sound from the front, surround, and surround back speakers.

XCN

Full Mono In this mode, all speakers output the same sound in mono, so the sound you hear is the same regardless of where you are within the listening room.

O r c e s t r ah

U n p u g g e dl

S t u i o M i xd

T V o g i cL

G a m R P Ge

G a m A c t i o ne

G a m R o c ke

G a m S p o r t se

A l l C h S t e r e o

F u l M o n ol

T-D (Theater- Dimensional)

With this mode you can enjoy a virtual surround sound even with only two or three speakers. This works by controlling how sounds reach the listeners left and right ears. Good results may not be possible if theres too much reverb, so we recommend that you use this mode in an environment with little or no natural reverb.

A S D F G H

ZXC N

Listening Mode Description Input Source

Speaker Layout

T D

Turning On & Basic Operations

En-38

Listening Modes

Listening Mode Description Input Source

Speaker Layout

Direct In this mode, audio from the input source is output without surround-sound processing. The speaker configuration (presence of speakers) and speaker distance settings are enabled, but much of the processing set via the audio setup is disabled. See On-screen Setup for more details ( page 43).

A S D F G H

ZXC N*1

Stereo Sound is output from the front left and right speakers and subwoofer.

ZXC N

Mono Use this mode when watching an old movie with a mono soundtrack, or use it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke DVDs.

Multichannel This mode is for use with PCM multichannel sources.

D F

XCN

DSD*2 In this mode, audio from the input source is output without surround-sound processing. The speaker configuration (presence of speakers), crossover frequency, speaker distance, A/V Sync and much of the processing set via the audio setup are enabled. See On-screen Setup for more details ( page 43).

D XCN

Dolby Digital

Dolby Digital Plus*3 D XCN F XCN*1

Dolby TrueHD D XCN F XCN*1

D i r e c t

S t e r e o

M o n o

M u l t i c h

D S D

D o l b y D

D o l b y D +

D o l b y T r u e H D

DTS In this mode, audio from the input source is output without surround-sound processing. The speaker configuration (presence of speakers), crossover frequency, speaker distance, A/V Sync and much of the processing set via the audio setup are enabled. See On-screen Setup for more details ( page 43).

D XCN

DTS-HD High Resolution Audio

D XCN F XCN*1

DTS-HD Master Audio

D XCN F XCN*1

DTS Express D XCN

DTS 96/24*4 This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a 96 kHz sampling rate and 24-bit resolution, providing superior fidelity. Use it with DVDs that bear the DTS 96/24 logo.

D XCN

DTS-ES Discrete*5 This mode is for use with DTS-ES Discrete soundtracks, which use a discrete surround back channel for true 6.1/7.1-channel playback. The seven totally separate audio channels provide better spatial imaging and 360-degree sound localization, perfect for sounds that pan across the surround channels. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS- ES Discrete soundtrack.

G V

DTS-ES Matrix*5 This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-encoded back-channel for 6.1/7.1-channel playback. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.

G V

Listening Mode Description Input Source

Speaker Layout

D T S

D T S H D H R

D T S H D MS T R

D T S E x p r e s s

D T S 9 6 / 2 4

E S i s c r e t eD

E S a t r i xM

Turning On & Basic Operations

En-39

Note *1 Based on the audio channel signal contained in the source, the corresponding speakers will output

the sound. *2 The AV receiver can input the DSD signal from HDMI IN. Depending on the player, setting the

output on the player side to PCM might bring better sound. *3 For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system. *4 DTS is used depending on the configuration of the AV receiver. *5 If there are no surround back speakers, DTS is used. *6 If there are no surround back speakers, Dolby Pro Logic II is used. The listening modes cannot be selected with some source formats.

Dolby Pro Logic IIx*6

Dolby Pro Logic II Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games can also benefit from the dramatic spatial effects and vivid imaging.

If youre not using any surround back speakers, Dolby Pro Logic II will be used instead of Dolby Pro Logic IIx. Dolby PLIIx Movie

Use this mode with any stereo or Dolby Surround (Pro Logic) movie (e.g., TV, DVD, VHS).

Dolby PLIIx Music Use this mode with any stereo or Dolby Surround (Pro Logic) music source (e.g., CD, radio, cassette, TV, VHS, DVD).

Dolby PLIIx Game Use this mode with video games, especially those that bear the Dolby Pro Logic II logo.

S XCN

Dolby PLIIx Movie Dolby PLIIx Music

These modes use the Dolby Pro Logic IIx modes to expand 5.1-channel sources for 7.1-channel playback.

D V

Dolby Pro Logic IIz Height

Dolby Pro Logic IIz Height is designed to more effectively use existing program material when height channel speaker outputs are present. Dolby Pro Logic IIz Height can be used to upmix a variety of sources from movies and music, but are particularly well-suited to upmix game content.

S D F G H

B

Dolby EX These modes expand 5.1-channel sources for 6.1/7.1-channel playback. Theyre especially suited to Dolby EX soundtracks that include a matrix-encoded surround back channel. The additional channel adds an extra dimension and provides an enveloping surround sound experience, perfect for rotating and fly-by sound effects.

D H

V

Listening Mode Description Input Source

Speaker Layout

P L M o v i e

P L M u s i c

P L G a m e

P L x M o v i e

P L x M u s i c

P L x G a m e

P L z H e i g h t

D o l b y E X

D o l b y D E X

DTS Neo:6 This mode expands any 2-channel source for up to 7.1-channel playback. It uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener.

DTS Neo:6 Cinema Use this mode with any stereo movie (e.g., TV, DVD, VHS).

DTS Neo:6 Music Use this mode with any stereo music source (e.g., CD, radio, cassette, TV, VHS, DVD).

S XCN

DTS Neo:6 This mode uses DTS Neo:6 to expand 5.1- channel sources for 6.1/7.1-channel playback.

D V

Listening Mode Description Input Source

Speaker Layout

N e o 6: C i n e m a

N e o 6 M u s i c:

N e o 6:

Turning On & Basic Operations

En-40

The Home menu provides quick access to frequently used menus.

Network Service

With this selection, you can use various Internet radio services or play the contents stored in media connected to your home network (DLNA) ( pages 26 to 29). Note that this selection will be grayed out for a short while after the AV receiver is turned on. Please wait until it becomes operable.

Press ENTER to display the network service screen. If you want to use the Internet radio services, use q/w/e/r to select the desired service. Pressing

ENTER again switches to that selection. If you want to play music files on a server, use q/w/e/r to select DLNA and then press ENTER.

USB With this selection, you can play contents of portable players (iPod, etc.) and USB storage devices connected to the AV receivers USB port ( pages 24, 25). Note that this selection will be grayed out for a short while after the AV receiver is turned on. Please wait until it becomes operable.

First, press USB repeatedly to select the USB(Front) or USB(Rear) input. Then, press ENTER to select a drive or browse the contents of the media connected, followed by q/w to select the desired folder or track. Pressing ENTER as a track is selected will start playback.

Note

Only the front-panel USB input is compatible with iPod/iPhone.

InstaPrevue With this selection, you can preview audio/video streams coming from HDMI inputs (HDMI IN 1/2/3/4/ AUX INPUT). Even with multiple components connected through HDMI, you can easily switch between inputs as their previews are displayed on a single screen.

Press ENTER to display the main preview (currently selected HDMI input) and the additional previews (other HDMI inputs). Using q/w or e/r to select a preview thumbnail and pressing ENTER will switch the AV receiver to that input source.

Setup With this selection, you can access the common settings of the on-screen Setup menu.

Press ENTER to display the Setup menu ( page 46).

Firmware Update With this selection, you can update the firmware of the AV receiver. Note that this selection will be grayed out for a short while after the AV receiver is turned on. Please wait until it becomes operable.

Press ENTER to start the procedure ( page 79).

Using the Home Menu

The Home menu appears only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receivers display when changing settings.

1 Press RECEIVER followed by HOME. The Home menu will be superimposed on the TV screen.

2 Use e/r or q/w and ENTER to make the desired selection. Press HOME to close the menu.

You need to connect the AV receiver to your home network ( page 89).

Tip

If no video signals are present, the thumbnails will be filled in black.

You can specify the number of preview thumbnails as well as their positioning on screen ( page 61).

Note

This function cannot be selected when: HDMI IN 5/6/7 is the current HDMI input source, or No signal is present on the current input source.

Depending on video signals, the picture may not be properly rendered on the preview thumbnails of InstaPrevue.

Tip

You can also access frequently used settings from Quick Setup ( page 43).

Turning On & Basic Operations

En-41

With the sleep timer, you can set the AV receiver to turn off automatically after a specified period.

You can adjust the brightness of the AV receivers display.

You can display various information about the current input source as follows.

The following information can be typically displayed.

*1 When AM or FM radio is used, the band, preset number, and frequency are displayed.

*2 If the input signal is digital, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears.

When you connect an u-capable Onkyo component, you must configure the input display so that u can work properly. This setting can be done only from the front panel.

Using the Sleep Timer

1 Press RECEIVER once followed by SLEEP repeatedly to select the required sleep time. The sleep time can be set from 90 to 10 minutes in 10 minute steps. The SLEEP indicator lights on the AV receivers display when the sleep timer has been set. The specified sleep time appears for about 5 seconds, then the previous display reappears.

Tip

If you need to cancel the sleep timer, press SLEEP repeatedly until the SLEEP indicator goes off.

To check the time remaining until the AV receiver sleeps, press SLEEP. Note that if you press again on SLEEP as the time being displayed is 10 minutes or less, the sleep timer will go off.

Setting the Display Brightness

1 Press RECEIVER once followed by DIMMER repeatedly to switch between: normal, dim, or dimmer brightness.

Tip

Alternatively, you can use DIMMER on the AV receiver.

Displaying Source Information

1 Press RECEIVER once followed by DISPLAY repeatedly to cycle through the available information.

Tip

Alternatively, you can use DISPLAY on the AV receiver.

Sampling frequency*2

Input source & volume*1

Signal format*2

Listening mode

Input signal resolution

Output resolution

Changing the Input Display

1 Press TV/CD or GAME. TV/CD or GAME appears on the AV receivers display.

2 Press and hold down the same button (about 3 seconds) to change the input display. Repeat this step to select the desired input display.

Note

DOCK can be selected for the TV/CD or GAME input selector, but not at the same time.

Enter the appropriate remote control code before using the remote controller for the first time ( page 70).

TV/CD DOCK

TAPE

TV/CD:

GAME DOCK GAME:

Turning On & Basic Operations

En-42

The Music Optimizer function enhances the sound quality of compressed music files.

You can temporarily mute the output of the AV receiver.

Using the Music Optimizer

1 Press MUSIC OPTIMIZER on the front panel. The M.Opt indicator lights on the AV receivers display. The MUSIC OPTIMIZER indicator lights on the front panel.

Tip

Alternatively, you can use Q SETUP on the remote controller.

See Music Optimizer for more details ( page 45).

Muting the AV Receiver

1 Press RECEIVER followed by MUTING. The output is muted and the MUTING indicator flashes on the AV receivers display.

Tip

To unmute, press MUTING again or adjust the volume. Muting is automatically cancelled when the AV receiver is

set to standby.

Using Headphones

1 Connect a pair of stereo headphones with a standard plug (1/4 inch or 6.3 mm) to the PHONES jack.

While the headphones plug is inserted in the PHONES jack, = indicator lights.

Note

Always turn down the volume before connecting your headphones.

While the headphones plug is inserted in the PHONES jack, the speakers are turned off. (The Powered Zone 2 speakers are not turned off.)

When you connect a pair of headphones, the listening mode is set to Stereo, unless its already set to Stereo, Mono, Direct.

If you connect an iPod or iPhone to the USB port on the AV receiver, no sound will be output from the headphones jack.

En-43

Advanced Operations

On-screen Setup With the AV receiver connected to a TV, there are two ways of changing the settings on-screen: using the Quick Setup or the Setup Menu (HOME).

Quick Setup The Quick Setup provides quick access to frequently used settings. You can change settings and view the current information.

Setup menu (HOME) The Setup menu (HOME) provides a convenient way to change the AV receivers various settings. Settings are organized into 9 categories.

Explanatory Notes

a Setting target

b Setting options (default setting underlined)

Input You can select input sources and view the following information: the name of input selectors, input assignments, radio information, and ARC function setting. In addition, previews of the video streams coming from HDMI inputs (HDMI IN 1/2/3/4/AUX INPUT) are displayed.*1 EXTRA1 and EXTRA2 can only be selected if they are assigned to HDMI, component, coaxial, or optical inputs. Use q/w to select an input source and view the related information. Pressing ENTER switches to the selected input source.

Audio ( page 44) You can change the following settings: Bass, Treble, Subwoofer Level, Center Level, Audyssey, Dynamic EQ, Dynamic Volume, Late Night, Music Optimizer, and Cinema Filter.

Video You can change the following settings: Wide Mode and Picture Mode*2.

See also: Picture Adjust ( page 56)

Information*3

You can view the information of the following items: Audio, Video and Tuner.

Listening Mode*4

You can select the listening modes that are grouped in the following categories: MOVIE/TV, MUSIC, GAME.

Use q/w to select the category and e/r to select the listening mode. Press ENTER to switch to the selected listening mode.

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receivers display when changing settings.

This section describes the procedure for using the remote controller unless otherwise specified.

Using the Quick Setup

1 Press RECEIVER followed by Q SETUP. The Quick Setup will be superimposed on the TV screen.

2 Use q/w and ENTER to make the desired selection. Press Q SETUP to close the menu. Press RETURN to return to the previous menu.

Q SETUP RETURN

RECEIVER

ENTER q/w/e/r

Music Optimizer Off On

a b

B D / D V D I n p u t A u d i o V i d e o I n f o r m a t i o n L i s t e n i n g M o d e

To be continued

Advanced Operations

En-44

Note

When the Monitor Out setting is set to Sub, Video cannot be selected.

*1 The video preview is not displayed when: HDMI IN 5/6/7 is the current HDMI input source, or No signal is present on the current input source.

The video of the currently-selected input is displayed on the main screen, not on a preview thumbnail.

*2 Only when you have selected Custom in the Picture Mode ( page 56), pressing ENTER allows you to adjust the following items via the Quick Setup: Brightness, Contrast, Hue and Saturation. Press RETURN to return to the Picture Mode setting.

*3 Depending on the input source and listening mode, not all channels shown here output the sound.

*4 This setting is not available in either of the following cases: The Audio TV Out setting is set to On ( page 60). HDMI Control(RIHD) is set to On ( page 60) and

youre listening through your TV speakers.

You can change various audio settings from the Quick Setup ( page 43).

Note

These settings are not available in either of the following cases: The Audio TV Out setting is set to On ( page 60). HDMI Control(RIHD) is set to On ( page 60) and

youre listening through your TV speakers.

Tone Control

Bass 10dB to 0dB to +10dB in 2 dB steps

You can boost or cut low-frequency sounds output from the front speakers.

Treble 10dB to 0dB to +10dB in 2 dB steps

You can boost or cut high-frequency sounds output from the front speakers.

You can adjust the bass and treble for the front speakers, except when Direct listening mode is selected.

Operating on the AV receiver

Speaker Levels

Subwoofer Level 15dB to 0dB to +12dB in 1 dB steps

Center Level 12dB to 0dB to +12dB in 1 dB steps

You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV receiver is set to standby. To save the setting you made here, go to Level Calibration ( page 51) before setting the AV receiver to standby.

Note

You cannot use these function while the AV receiver is muted. These settings cannot be used while a pair of headphones is

connected. Speakers that are set to No or None in

Speaker Configuration ( page 50) cannot be adjusted.

Audyssey

Audyssey See Audyssey in Source Setup ( page 53).

Dynamic EQ See Dynamic EQ in Source Setup ( page 54).

Dynamic Volume See Dynamic Volume in Source Setup ( page 54).

Note

These technologies can be used when all the following conditions are met: Room Correction and Speaker Setup is completed. Note that

Audyssey requires the Audyssey 2EQ Full Calibration method.

Any listening mode other than Direct is selected. A pair of headphones is not connected.

The setting is stored individually for each input selector.

Using the Audio Settings of Quick Setup

1 Press TONE repeatedly to select either Bass or Treble.

2 Use and + to adjust.

Advanced Operations

En-45

Late Night

Late Night For Dolby Digital and Dolby Digital Plus sources, the options are:

Off Low:

Small reduction in dynamic range. High:

Large reduction in dynamic range.

For Dolby TrueHD sources, the options are: Auto:

The Late Night function is set to On or Off automatically.

Off On

Turn this setting on to reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levelsideal for watching movies late at night when you dont want to disturb anyone.

Note

The effect of the Late Night function depends on the material that you are playing and the intention of the original sound designer, and with some material there will be little or no effect when you select the different options.

The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.

The Late Night function is set to Off when the AV receiver is set to standby. For Dolby TrueHD sources, it will be set to Auto.

With Dolby TrueHD sources, the Late Night function cannot be used when TrueHD Loudness Management is set to Off ( page 53).

Music Optimizer

Music Optimizer Off On

The Music Optimizer function enhances the sound quality of compressed music files. When set to On, the M.Opt indicator lights on the AV receivers display, and the MUSIC OPTIMIZER indicator lights on the front panel.

Tip

Alternatively, you can use MUSIC OPTIMIZER on the AV receiver.

Note

The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48 kHz and analog audio input signals.

The Music Optimizer is disabled when the Direct listening mode is selected.

The setting is stored individually for each input selector.

CinemaFILTER

Cinema Filter Off On

Turn this setting on to soften overly bright movie soundtracks, which are typically mixed for reproduction in a movie theater. CinemaFILTER can be used with the following listening modes: Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Pro Logic IIx Movie, Dolby Pro Logic II Movie, Dolby Pro Logic IIz Height, Multichannel, DTS, DTS-ES, DTS Neo:6 Cinema, DTS 96/24, DTS Neo:6, DTS-HD High Resolution Audio, DTS-HD Master Audio and DTS Express.

Note

The CinemaFILTER may not work when used with certain input sources.

Advanced Operations

En-46

Note

This procedure can also be performed on the AV receiver by using SETUP, the cursor buttons, and ENTER.

During Audyssey 2EQ Room Correction and Speaker Setup, messages, etc., that are displayed on the TV screen will appear on the AV receivers display.

Explanatory Notes

a Main Menu

b Sub Menu

c Setting target

d Setting options (default setting underlined)

Using the Setup Menu (HOME)

1 Press RECEIVER followed by HOME.

2 Use e/r to select Setup, and then press ENTER.

3 Use q/w to select a main menu item, and then press ENTER.

4 Use q/w to select a sub menu item, and then press ENTER.

5 Use q/w to select a setting target, and use e/r to change the setting. Press HOME to close the menu. Press RETURN to return to the previous menu.

RETURN

HOME

RECEIVER

ENTER q/w/e/r

Remote indicator

Screen Saver If there is no video signal on the current input source and no operation for a specific time (three minutes by default), a screen saver automatically comes on.

Tip

The time until the screen saver activates itself can be changed in the Screen Saver setting ( page 59).

The screen will return to its previous state if the AV receiver is operated.

Main Menu Speaker Setup

Speaker Configuration

Subwoofer Yes No

a

b

d c

Main Menu

Sub Menu

Advanced Operations

En-47

By way of optimized circuitry, this function reduces power consumption when the AV receiver is in standby mode. The HYBRID STANDBY indicator will light in either of the following conditions:

HDMI Through is enabled (the HDMI indicator is off).

Network Standby is enabled (the NET indicator is off).

Note

If Zones are turned on or, if a mobile device connected to the Front Input (MHL) is charging, the HYBRID STANDBY indicator wont light.

About the HYBRID STANDBY indicator

HYBRID STANDBY

Setup menu items

Main menu item Sub menu item

Input/Output Assign ( page 48)

Monitor Out

HDMI Input

Component Video Input

Digital Audio Input

Speaker Setup ( page 50)

Speaker Settings

Speaker Configuration

Speaker Distance

Level Calibration

Audio Adjust ( page 52)

Multiplex/Mono

Dolby

DTS

Theater-Dimensional

Source Setup ( page 53)

Audyssey

IntelliVolume

A/V Sync

Name Edit

Picture Adjust

Audio Selector

Listening Mode Preset ( page 58)

BD/DVD

CBL/SAT

GAME

PC

AUX

TUNER

TV/CD

NET

USB

EXTRA1

EXTRA2

Miscellaneous ( page 59)

Volume Setup

OSD Setup

Hardware Setup ( page 59)

Tuner

HDMI

Auto Standby

Network

Initial Setup

Remote Controller Setup ( page 63)

Remote ID

Remote Mode Setup

Lock Setup ( page 63)

Setup

Main menu item Sub menu item

Advanced Operations

En-48

Main Menu Input/Output Assign

Monitor Out

On the Monitor Out settings, you can select whether or not to have the video sources images output through the HDMI output. If you connect your TV to HDMI output, Monitor Out setting is automatically set and composite video and component video sources are upconverted* and output.

Note

See Video Connection Formats ( page 83) for charts showing how the Monitor Out and Resolution settings affect the video signal flow through the AV receiver.

Monitor Out Main:

Select this if your TV is connected to HDMI OUT MAIN.

Sub: Select this if your TV is connected to HDMI OUT SUB.

Both: Select this if your TVs are connected to HDMI OUT MAIN and HDMI OUT SUB. Video signals are

output from both HDMI outputs at the resolution supported by both TVs.

Resolution Through:

Select this to pass video through the AV receiver at the same resolution and with no conversion.

Auto: Select this to have the AV receiver automatically convert video at resolutions supported by your TV.

480p, 720p, 1080i, 1080p: Select the desired output resolution.

1080p/24: Select this for 1080p output at 24 frames per second.

4K Upscaling: Select this for an output resolution four times that of 1080p. Depending on the resolution supported by your TV, it will result in either 3840 2160 or 4096 2160 pixels.

You can specify the output resolution for the HDMI OUT MAIN and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV.

Tip

You can see the picture by pressing ENTER to check the Resolution setting (excluding NET input source).

Note

Depending on the incoming video signal, the video playback may not be smooth or the vertical resolution may be lowered. In this case select anything other than 1080p/24.

With some TVs, there may be no picture when this setting is set to 4K Upscaling.

If the Monitor Out setting is set to Sub, this setting is fixed to Through.

If the Monitor Out setting is set to Both, this setting is fixed to Auto.

HDMI Input

If you connect a video component to an HDMI input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to HDMI IN 2, you must assign HDMI2 to the BD/DVD input selector. If youve connected your TV to the AV receiver with an HDMI cable, composite video and component video sources can be upconverted* and output by the HDMI output. You can set this for each input selector by selecting the - - - - - option. See Video Connection Formats for more information on video signal flow and upconversion ( page 83).

Here are the default assignments.

Input/Output Assign

1 2 3 4 5 Setup

IN

OUT

Composite video, component video HDMI

HDMIComposite video, component video

Input selector Default assignment

BD/DVD HDMI1

CBL/SAT HDMI2

GAME HDMI3

PC HDMI4

AUX FRONT (Fixed)

TV/CD - - - - -

EXTRA1 - - - - -

EXTRA2 - - - - -

IN

OUT

Composite video, component video HDMI

HDMIComposite video, component video

Advanced Operations

En-49

BD/DVD, CBL/SAT, GAME, PC, TV/CD, EXTRA1, EXTRA2

HDMI1, HDMI2, HDMI3, HDMI4, HDMI5, HDMI6, HDMI7:

Select the input to which the component has been connected.

- - - - -: Output composite video and component video sources from the HDMI output. The video output signal from the HDMI output is the one configured in Component Video Input.

Each HDMI input cannot be assigned to two input selectors or more. When HDMI1 - HDMI7 have already been assigned, you must first set any unused input selectors to - - - - - or you will be unable to assign HDMI1 - HDMI7 to other input selectors.

Tip

EXTRA1 and EXTRA2 can be selected as input sources in Input of Quick Setup ( page 43).

Note

If no video component is connected to HDMI output (even if the HDMI input is assigned), the AV receiver selects the video source based on the setting of Component Video Input.

When an HDMI IN is assigned to an input selector as explained here, the same HDMI IN will be set as a priority in the Digital Audio Input. In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the Audio Selector setting ( page 57).

Do not assign an HDMI IN to the TV/CD selector while HDMI Control(RIHD) is set to On ( page 60), otherwise appropriate CEC (Consumer Electronics Control) operation will not be guaranteed.

If you assign - - - - - to an input selector that is currently selected in HDMI Through ( page 60), the HDMI Through setting will be automatically switched to Off.

AUX is used only for input from the front panel.

Component Video Input

If you connect a video component to a component video input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to COMPONENT VIDEO IN, you must assign IN1 to the BD/DVD input selector. Here are the default assignments.

BD/DVD, CBL/SAT, GAME, PC, TV/CD, EXTRA1, EXTRA2

IN1: Select the input to which the component has been connected.

- - - - -: Output composite video sources from the HDMI output.

Tip

EXTRA1 and EXTRA2 can be selected as input sources in Input of Quick Setup ( page 43).

Note

When composite video and component video sources are upconverted for HDMI OUT SUB, only signals with a resolution of 480i are output and the resolution remains the same. If your TV doesnt support this resolution, there will be no picture ( page 85).

AUX is fixed to the - - - - - option.

Digital Audio Input

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign OPTICAL1 to the TV/CD input selector. Here are the default assignments.

BD/DVD, CBL/SAT, GAME, PC, TV/CD, EXTRA1, EXTRA2

COAXIAL1, COAXIAL2, OPTICAL1, OPTICAL2:

Select the input to which the component has been connected.

- - - - -: Select if the component is connected to an analog audio input.

Tip

EXTRA1 and EXTRA2 can be selected as input sources in Input of Quick Setup ( page 43).

Note

When an HDMI IN is assigned to an input selector in HDMI Input ( page 48), the same HDMI IN will be set as a priority in this assignment. In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the Audio Selector ( page 57).

Supported sampling rates for PCM signals (stereo/mono) from a digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

AUX is fixed to the - - - - - option.

Input selector Default assignment

BD/DVD - - - - -

CBL/SAT IN1

GAME - - - - -

PC - - - - -

AUX - - - - - (Fixed)

TV/CD - - - - -

EXTRA1 - - - - -

EXTRA2 - - - - -

Input selector Default assignment

BD/DVD COAXIAL1

CBL/SAT COAXIAL2

GAME OPTICAL1

PC - - - - -

AUX - - - - - (Fixed)

TV/CD OPTICAL2

EXTRA1 - - - - -

EXTRA2 - - - - -

Advanced Operations

En-50

Main Menu Speaker Setup

Here you can check the settings made by Audyssey 2EQ Room Correction and Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using Audyssey 2EQ Room Correction and Speaker Setup function.

Speaker Settings

If you bi-amp the front speakers, you must change the Speakers Type (Front) setting. For details on speaker wire connection, see Bi-amping the Front Speakers ( page 13).

Note

When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers in the main room.

Before you change these settings, turn down the volume.

Speakers Type (Front) Normal:

Select this if youve connected your front speakers normally.

Bi-Amp: Select this if youve bi-amped your front speakers.

Powered Zone 2 No Yes:

Zone 2 speakers can be used. (Powered Zone 2 enabled).

Note

If the Speakers Type (Front) setting is set to Bi-Amp, Powered Zone 2 cannot be used.

When the Powered Zone 2 setting is set to Yes and Zone 2 is turned on, the surround back and front high speakers cannot be used.

Speaker Configuration

With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify Full Band for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speakers manuals to determine the optimum crossover frequencies.

Subwoofer Yes No

Front Full Band 40Hz to 100Hz, 120Hz, 150Hz, 200Hz

Note

If the Subwoofer setting is set to No, the Front setting is fixed at Full Band.

Center*1, Surround*1

Full Band 40Hz to 100Hz, 120Hz, 150Hz, 200Hz None

Front High*1*2*3*5

Full Band 40Hz to 100Hz, 120Hz, 150Hz, 200Hz None

Surround Back*1*2*3*4

Full Band 40Hz to 100Hz, 120Hz, 150Hz, 200Hz None

Note *1 Full Band can be selected only when Full Band is

selected in the Front setting. *2 If the Surround setting is set to None, this setting cannot

be selected. *3 If the Speakers Type (Front) setting is set to Bi-Amp, or

the Powered Zone 2 setting is set to Yes together with Zone 2 turned on, this setting cannot be selected.

*4 If anything else than None is selected in Front High, this setting is automatically set to None.

*5 If anything else than None is selected in Surround Back, this setting is automatically set to None.

Surround Back Ch 1ch:

Select if only one surround back speaker L is connected.

2ch: Select if two (left and right) surround back speakers are connected.

Note

If the Surround Back setting is set to None, this setting cannot be selected.

If the Powered Zone 2 setting is set to Yes and Zone 2 is turned on, this setting cannot be selected.

Speaker Setup

Some of the settings in this section are set automatically by Audyssey 2EQ Room Correction and Speaker Setup ( page 32).

If you change these settings, you must run Audyssey 2EQ Room Correction and Speaker Setup again ( page 32).

1 2 3 4 5 Setup

This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup ( page 32).

Advanced Operations

En-51

LPF of LFE (Low-Pass Filter for the LFE Channel)

80Hz, 90Hz, 100Hz, 120Hz Off:

Low-Pass Filter is not applied. With this setting, you can specify the cutoff frequency of the LFE channels low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

Double Bass

On Off

Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer.

Note

When the Subwoofer setting is set to No or the Front setting to anything other than Full Band, this setting is fixed to - - -.

This setting is set to On automatically when the Subwoofer and Front settings are set for the first time to Yes and Full Band respectively.

Speaker Distance

Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listeners ears as the sound designer intended.

Unit feet:

Distances can be set in feet. Range: 1.0ft to 30.0ft in 1.0 foot steps.

meters: Distances can be set in meters. Range: 0.30m to 9.00m in 0.30 meter steps.

Left, Front High Left, Center, Front High Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left, Subwoofer

Specify the distance from each speaker to your listening position.

Note

Speakers that you set to No or None in Speaker Configuration cannot be selected ( page 50).

When the Powered Zone 2 setting is set to Yes and Zone 2 is turned on, the surround back and front high speakers cannot be used.

Level Calibration

Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position.

Note

These settings cannot be calibrated in either of the following cases: The Audio TV Out setting is set to On ( page 60). HDMI Control(RIHD) is set to On ( page 60) and

youre listening through your TV speakers. The AV receiver is muted.

Left, Front High Left, Center*1, Front High Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left

12dB to 0dB to +12dB in 1 dB steps.

Subwoofer*1

15dB to 0dB to +12dB in 1 dB steps.

Note

Speakers that you set to No or None in Speaker Configuration cannot be selected ( page 50).

When the Powered Zone 2 setting is set to Yes and Zone 2 is turned on, the surround back and front high speakers cannot be used.

*1 For the center speaker and subwoofer, the level settings made by using the Quick Setup are saved in this menu ( page 44).

Tip

If youre using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading.

This setting is NOT set automatically by Audyssey 2EQ Room Correction and Speaker Setup ( page 32).

This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup ( page 32).

This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup ( page 32).

Advanced Operations

En-52

Main Menu Audio Adjust

With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like.

Multiplex/Mono

Multiplex

Input Channel Main Sub Main/Sub

This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.

Mono

Input Channel Left + Right Left Right

This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or 2- channel analog/PCM source in the Mono listening mode.

Dolby

PL IIx Music (2ch Input) These settings apply to only 2-channel stereo sources. If youre not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro Logic IIx.

Panorama On Off

With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode.

Dimension 3 to 0 to +3

With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. Higher settings move the sound field backward. Lower settings move it forward. If the stereo image feels too wide, or theres too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like its in mono, or theres not enough surround sound, move it backward.

Center Width 0 to 3 to 7

With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic IIx Music listening mode. Normally, if youre using a center speaker, the center channel sound is output from only the center speaker. (If youre not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound.

PL IIz Height Gain Low Mid High

The Height Gain Control in Dolby Pro Logic IIz enables the listener to select how much gain is applied to the front high speakers. There are three settings, Low, Mid and High, and the front high speakers are accentuated in that order. While Mid is the default listening setting, the listener may adjust the Height Gain Control to their personal preference.

Note

If the Front High setting is set to None ( page 50), this setting cannot be selected.

If the Powered Zone 2 setting is set to Yes ( page 50) and Zone 2 is turned on, this setting cannot be selected.

Dolby EX Auto:

If the source signal contains a Dolby EX flag, the Dolby EX listening mode is used.

Manual: You can select any available listening mode.

This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround back speakers are connected. This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD only.

Note

If the Surround Back setting is set to None ( page 50), this setting cannot be selected.

If the Powered Zone 2 setting is set to Yes ( page 50) and Zone 2 is turned on, this setting cannot be selected.

Audio Adjust

1 2 3 4 5 Setup

Advanced Operations

En-53

TrueHD Loudness Management Off On

This setting specifies whether or not to apply the Late Night processing on a Dolby TrueHD source.

Note

When this setting is set to Off, the Late Night function for Dolby TrueHD sources is automatically fixed to Off ( page 45).

DTS

Neo:6 Music

Center Image 0 to 2 to 5

The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. Changing the value from 0 to 5 will spread the sound of the center channel to left and right (outwards).

Theater-Dimensional

Listening Angle Wide:

Select if the listening angle is greater than 30 degrees. Narrow:

Select if the listening angle is less than 30 degrees. With this setting, you can optimize the Theater- Dimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings.

Note

For best results, we recommend setting Narrow to 20 and Wide to 40.

Items can be set individually for each input selector.

Main Menu Source Setup

Audyssey

Audyssey Off Movie:

Select this setting for movie material. The Audyssey indicator will light.

Music: Select this setting for music material. The Audyssey indicator will light.

Note

When Audyssey Quick Start has been used for measurement, Audyssey cannot be selected.

Audyssey equalizing does not work with DSD sources.

Front left speaker Front right speaker

Listening angle: 30

Source Setup

Preparation Press the input selector buttons to select an input source.

The tone for each speaker is set automatically by Audyssey 2EQ Room Correction and Speaker Setup. To enable the following settings, you must first perform the Room Correction and Speaker Setup ( page 32). These technologies cannot be used when:

a pair of headphones is connected, or Direct listening mode is selected.

1 2 3 4 5 Setup

Advanced Operations

En-54

Dynamic EQ Off On:

Audyssey Dynamic EQ becomes active. The Dynamic EQ indicator will light.

With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels. Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. It does so by selecting the correct frequency response and surround volume levels moment-by-moment so that the content sounds the way it was created at any volume level not just at reference level.

Reference Level Audyssey Dynamic EQ Reference Level Offset

0dB: This should be selected for movie contents.

5dB: Select this setting for content that has a very wide dynamic range, such as classical music.

10dB: Select this setting for jazz or other music that has a wider dynamic range. This setting should also be selected for TV content as that is usually mixed at 10 dB below film reference.

15dB: Select this setting for pop/rock music or other program material that is mixed at very high listening levels and has a compressed dynamic range.

Movies are mixed in rooms calibrated for film reference. To achieve the same reference level in a home theater system each speaker level must be adjusted so that 30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home theater system automatically calibrated by Audyssey 2EQ will play at reference level when the master volume control is set to the 0 dB position. At that level you can hear the mix as the mixers heard it.

Audyssey Dynamic EQ is referenced to the standard film mix level. It makes adjustments to maintain the reference response and surround envelopment when the volume is turned down from 0 dB. However, film reference level is not always used in music or other non-film content. Audyssey Dynamic EQ Reference Level Offset provides three offsets from the film level reference (5 dB, 10 dB, and 15 dB) that can be selected when the mix level of the content is not within the standard.

Note

If Dynamic EQ setting is set to Off, this technology cannot be used.

Dynamic Volume Off Light:

Activates Light Compression Mode. Medium:

Activates Medium Compression Mode. Heavy:

Activates Heavy Compression Mode. This setting affects volume the most. It quiets the loud parts, such as explosions, and boosts the quiet parts so they can be heard.

Note

If you make Dynamic Volume active, Dynamic EQ is set to On. The Dynamic Vol indicator will light.

When Dynamic EQ is set to Off, Dynamic Volume is automatically switched to Off.

About Audyssey Dynamic EQ

Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user-selected volume setting. The result is bass response, tonal balance, and surround impression that remain constant despite changes in volume. Dynamic EQ combines information from incoming source levels with actual output sound levels in the room, a prerequisite for delivering a loudness correction solution. Audyssey Dynamic EQ works well by itself. However, if Audyssey 2EQ is on, the two technologies work in tandem to provide well-balanced sound for every listener at any volume level.

About Audyssey Dynamic Volume

Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression and dialog clarity remain the same whether watching movies, flipping between television channels or changing from stereo to surround sound content.

Advanced Operations

En-55

IntelliVolume

IntelliVolume 12dB to 0dB to +12dB in 1 dB steps.

With IntelliVolume, you can set the input level for each input selector individually. This is useful if one of your source components is louder or quieter than the others.

Use e/r to set the level.

If a component is noticeably louder than the others, use e to reduce its input level. If its noticeably quieter, use r to increase its input level.

Note

IntelliVolume does not work for Zone 2.

A/V Sync

A/V Sync 0 msec to 800 msec in 10 msec steps

When using progressive scanning on your Blu-ray Disc/DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals. To view the TV picture while setting the delay, press ENTER. To return to the previous screen, press RETURN.

The range of values you can adjust will depend on whether your TV or display supports HDMI Lip Sync and if the LipSync setting is set to On or not ( page 61).

Note

A/V Sync is disabled when the Direct listening mode is used with an analog input source.

This setting cannot be used with the NET input selector.

Name Edit

You can enter a custom name for each individual input selector and radio preset for easy identification. When entered, the custom name will appear on the display. The custom name is edited using the keyboard screen.

Name

Tip

To name a radio preset, select AM or FM, and then select the preset ( page 31).

To restore a name to its default, erase all characters with CLR, select OK and then press ENTER.

Note

This setting cannot be used for the NET and USB input selectors.

1 Use q/w/e/r to select a character, and then press ENTER. Repeat this step to enter up to 10 characters.

2 To store a name when youre done, be sure to select OK by using q/w/e/r, and then press ENTER.

BD/DVD

Shift All Erase

Shift All Erase

4 - 4. Name Edit Name

+10 CLR

+10 CLR

a b c d e f g h i j k l m n o p q r s t u v w x y z

1 2 3 4 5 6 7 8 9 0 ^ \ Space

Back Space Shift OK , . / ; : @ [ ]

Space Back Space Shift OK

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

+ ? ` { } < > ! # $ % & ) ( _ = |

Name input area

Space: Enters a space character.

Shift*1: Toggles between lower and upper case characters.

(Left)/ (Right): Moves the cursor left or right in the Name input area.

Back Space*2: Moves the cursor backward and deletes one character.

OK: Confirms your entry.

Tip *1 This can also be performed by using +10 on the remote

controller. *2 Press CLR on the remote controller to delete all the

characters you have input.

Advanced Operations

En-56

Picture Adjust

Using Picture Adjust, you can adjust the picture quality and reduce any noise appearing on the screen. To view the TV picture while setting, press ENTER. To return to the previous screen, press RETURN.

Wide Mode*1*6

This setting determines the aspect ratio. 4:3:

Full:

Zoom:

Wide Zoom:

Auto: According to the input signals and monitor output setting, the AV receiver automatically selects the 4:3, Full, Zoom or Wide Zoom mode. See Monitor Out for details on the monitor output setting ( page 48).

Picture Mode*1

Custom: All settings can be performed manually.

Cinema: Select when the picture source is a movie or alike.

Game: Select when the video source is a game console.

Through: Does not adjust picture quality (changes resolution).

Direct: Does not adjust picture quality (does not change resolution). The video coming from an analog input and output by HDMI output(s) is processed in the same way as Through.

With Picture Mode, you can change the following settings to be suitable for the movie or game screen by one operation; Game Mode, Film Mode, Edge Enhancement, Noise Reduction, Brightness, Contrast, Hue, Saturation or Color Temperature.

Game Mode*2*3*4

Off On

If video signal delay occurs during playback on a video component (i.e., game console), select the corresponding input source and set the Game Mode setting to On. The delay will decrease but in return the picture quality will become poor.

Film Mode*2*4

Video: Film Mode detection is not applied and the input signal is handled as a video source.

Auto: Detects whether the input signal is a video or a movie. If it is a movie, the appropriate conversion is applied.

The AV receiver will adjust to the picture source, automatically converting it to the appropriate progressive signal and reproducing the natural quality of the original picture.

Edge Enhancement*2*4*5

Off Low Mid High

With this setting, you can make the picture appear sharper.

Noise Reduction*2*4*5

Off Low Mid High

With this setting, you can reduce noise appearing on the screen. Select the desired level.

Advanced Operations

En-57

Brightness*1*2*4

50 to 0 to +50 With this setting, you can adjust the picture brightness. 50 is the darkest. +50 is the brightest.

Contrast*1*2*4

50 to 0 to +50 With this setting, you can adjust contrast. 50 is the least. +50 is the greatest.

Hue*1*2*4

50 to 0 to +50 With this setting, you can adjust the color hue between 50 and +50.

Saturation*1*2*4

50 to 0 to +50 With this setting, you can adjust saturation. 50 is the weakest color. +50 is the strongest color.

Color Temperature*2*4

Warm Normal Cool

With this setting, you can adjust the color temperature.

Note

Picture Adjust cannot be used when: The NET input selector is selected, or Monitor Out is set to Sub.

*1 This procedure can also be performed on the remote controller by using the Quick Setup ( page 43).

*2 When the Picture Mode setting is set to anything other than Custom, this setting cannot be used.

*3 If the Resolution setting is set to 4K Upscaling ( page 48), this setting is fixed at Off.

*4 Press CLR if you want to reset to the default value. *5 If the Game Mode setting is set to On, this setting is fixed

at Off. *6 When a 3D video source is input, Wide Mode is fixed to

Full.

Audio Selector

Audio Selector ARC:

The audio signal from your TV tuner can be sent to HDMI OUT MAIN of the AV receiver.*1 With this selection, the TVs audio can be automatically selected as a priority among other assignments.

HDMI: This can be selected when HDMI IN has been assigned as an input source. If both HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) have been assigned, HDMI input is automatically selected as a priority.

COAXIAL: This can be selected when COAXIAL IN has been assigned as an input source. If both coaxial and HDMI inputs have been assigned, coaxial input is automatically selected as a priority.

OPTICAL: This can be selected when OPTICAL IN has been assigned as an input source. If both optical and HDMI inputs have been assigned, optical input is automatically selected as a priority.

Analog: The AV receiver always outputs analog signals.

You can set priorities of audio output when there are both digital and analog inputs.

Note

This setting can be made only for an input source that is assigned to HDMI IN, COAXIAL IN, or OPTICAL IN.

This setting cannot be used with the NET and USB input selectors.

*1 You can select ARC if you select the TV/CD input selector. But you cannot if youve selected Off in the Audio Return Channel setting ( page 61).

Setting the Incoming Digital Signal (Fixed Mode)

Fixed Mode Off:

The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.

PCM: Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and noise may also be produced.

DTS: Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the dts indicator will flash and there will be no sound.

When HDMI, COAXIAL or OPTICAL is selected in the Audio Selector setting, you can then specify the signal type in Fixed Mode. Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS. If the beginnings of tracks from a PCM source are cut off,

try setting the format to PCM. If noise is produced when fast forwarding or reversing a

DTS CD, try setting the format to DTS.

Note

The setting will be reset to Off when you change the setting in Audio Selector.

Advanced Operations

En-58

Main Menu Listening Mode Preset

You can assign a default listening mode to each input source that will be selected automatically when you select each input source. For example, you can set the default listening mode to be used with Dolby Digital input signals. You can select other listening modes during playback, but the mode specified here will be resumed once the AV receiver has been set to standby.

Analog/PCM/Digital With this setting, you can specify the listening mode used when an analog (CD, TV, LD, VHS, MD, turntable, radio, cassette, cable, satellite, etc.) or PCM digital (CD, DVD, etc.) audio signal is played.

Note

For the AUX, EXTRA1, and EXTRA2 input selectors, only PCM is available.

Mono/Multiplex Source With this setting, you can specify the listening mode used when a mono digital audio signal is played (DVD, etc.).

2ch Source With this setting, you can specify the listening mode used when 2-channel (2/0) stereo digital sources, such as Dolby Digital or DTS, are played.

Dolby D/Dolby D Plus/TrueHD With this setting, you can specify the listening mode used when Dolby Digital or Dolby Digital Plus format digital audio signals are played (DVD, etc.). Specifies the default listening mode for Dolby TrueHD sources, such as Blu-ray or HD DVD (input via HDMI).

DTS/DTS-ES/DTS-HD With this setting, you can specify the listening mode used when DTS or DTS-HD High Resolution format digital audio signals are played (DVD, LD, CD, etc.). Specifies the default listening mode for DTS-HD Master Audio sources, such as Blu-ray or HD DVD (input via HDMI).

Other Multich Source Specifies the default listening mode for multichannel PCM sources from HDMI IN such as DVD-Audio, and DSD multichannel sources such as Super Audio CD.

Listening Mode Preset

1 Use q/w to select the input source that you want to set, and then press ENTER. The following menu appears.

1 2 3 4 5 Setup

Default listening mode for analog and PCM sources.

Analog/PCM Mono/Multiplex Source 2ch Source Dolby D/Dolby D Plus/TrueHD DTS/DTS-ES/DTS-HD Other Multich Source

Last Valid er

5-1. Listening Mode Preset BD/DVD

Last Valid Last Valid Last Valid Last Valid Last Valid

2 Use q/w to select the signal format that you want to set, and then use e/r to select a listening mode. Only listening modes that can be used with each input signal format can be selected ( pages 35 to 39). The Last Valid option means that the listening mode selected last will be used. The Straight Decode option means that straight decoding listening mode (Dolby Digital, DTS, etc.) is selected.

Note

For the AM or FM input selector, only Analog will be available.

For the NET or USBinput selector, only Digital will be available.

Advanced Operations

En-59

Main Menu Miscellaneous

Volume Setup

Maximum Volume Off, 30 to 79

With this setting, you can limit the maximum volume. To disable this setting, select Off.

Power On Volume Last, Min, 1 to 79 or Max

With this setting, you can specify the volume setting to be used each time the AV receiver is turned on. To use the same volume level that was used when the AV receiver was turned off, select Last. The Power On Volume setting cannot be set higher than the Maximum Volume setting.

Headphone Level 12dB to 0dB to +12dB

With this setting, you can specify the headphone volume relative to the main volume. This is useful if theres a volume difference between your speakers and your headphones.

OSD Setup

On Screen Display On Off

This preference determines whether operation details are displayed on-screen when an AV receiver function is adjusted. Even when On is selected, operation details may not be output if the input source is connected to an HDMI IN.

Language English, Deutsch, Franais, Espaol, Italiano, Nederlands, Svenska

This setting determines the language used for the on-screen menus.

Screen Saver 3 min, 5 min, 10 min Off

With this setting, you can set the time until the screen saver activates itself. Once active, the screen saver will go off and the screen will return to its previous state if the AV receiver is operated in any way.

Main Menu Hardware Setup

Tuner

AM/FM Frequency Step 10kHz/200kHz: 9kHz/50kHz:

Select the frequency step according to your area. For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area.

Note

When this setting is changed, all radio presets will be deleted.

Miscellaneous

1 2 3 4 5 Setup

Hardware Setup

1 2 3 4 5 Setup

Advanced Operations

En-60

HDMI

HDMI Control(RIHD) Off On

Turn this setting on to allow p-compatible components connected via HDMI to be controlled by the AV receiver ( page 86).

Note

When the setting is set to On and the menu is closed, the names of connected p-compatible components and RIHD On are displayed on the AV receiver. Search (name) RIHD On When the AV receiver cannot receive the name of the component, it is displayed as Player* or Recorder*, etc. (* shows up and indicates the number of components, when two or more are received).

When an p-compatible component is connected to the AV receiver via an HDMI cable, the name of the connected component is displayed on the AV receiver display. For example, while you are watching TV broadcasting, if you operate a Blu-ray Disc/DVD player (being powered on) with the remote control of the AV receiver, the name of the Blu-ray Disc/DVD player will be displayed on the AV receiver.

Set it to Off when a connected piece of equipment is not compatible or it is unclear whether the equipment is compatible or not.

If operation is not normal when set to On, change the setting to Off.

Refer to the connected components instruction manual for details.

When the HDMI Control(RIHD) setting is set to On, the power consumption on standby mode slightly increases. (Depending on the TV status, the AV receiver will enter standby mode as usual.)

The p control does not support HDMI OUT SUB. Use HDMI OUT MAIN instead.

When the source equipment is connected with the u connection, it may malfunction if HDMI Control(RIHD) is set to On.

HDMI Through Off BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD, EXTRA1, EXTRA2:

Selects the input source for which the HDMI Through function is enabled.

Last: The HDMI Through function is activated on the input source selected at the time of setting the AV receiver to standby mode.

When enabling the HDMI Through function, regardless of whether the AV receiver is on or in standby, both audio and video streams from an HDMI input will be output to the TV or other components via HDMI connection. The HDMI indicator will be dimly-lit in standby mode. Note that the indicator may not light under certain conditions ( page 47). This setting is fixed to Auto automatically when the above HDMI Control(RIHD) setting is set to On, resulting in automatic input source selection.

Note

Only an input source assigned to an HDMI IN via HDMI Input setting is enabled ( page 48).

The power consumption in standby mode will increase during the HDMI Through function; however in the following cases, the power consumption can be saved: The TV is in standby mode. You are watching a TV program.

Refer to the connected components instruction manual for details.

Depending on the connected component, the correct input source may not be selected with the setting fixed to Auto.

This setting is set to Off automatically when the HDMI Control(RIHD) setting is set to Off.

Audio TV Out Off On

This preference determines whether the incoming audio signal is output from the HDMI output. You may want to turn this preference on if your TV is connected to the HDMI output and you want to listen to the audio from a connected component through your TVs speakers. Normally, this should be set to Off.

Note

If On is selected and the audio can be output from the TV, the AV receiver will output no sound through its speakers. In this case, TV Speaker appears on the AV receivers display by pressing DISPLAY.

When HDMI Control(RIHD) is set to On, this setting is fixed to Auto.

With some TVs and input signals, no sound may be output even when this setting is set to On.

When Audio TV Out or HDMI Control(RIHD) is set to On and youre listening through your TVs speakers ( page 15), turning up the AV receivers volume control will make the sound be output from the AV receivers front left and right speakers. To stop the AV receivers speakers producing sound, change the settings, change your TVs settings, or turn down the AV receivers volume.

Listening mode cannot be changed when this setting is set to On and the input source is not HDMI.

Advanced Operations

En-61

Audio Return Channel (ARC) Off Auto:

The audio signal from your TV tuner can be sent to HDMI OUT MAIN of the AV receiver.

The audio return channel (ARC) function allows an ARC capable TV to send the audio stream to HDMI OUT MAIN of the AV receiver. To use this function, you must select the TV/CD input selector and your TV must be ARC capable. The ARC indicator will light when the audio signal is detected. Default setting: - - - -

Note

This setting is fixed to - - - - when the HDMI Control(RIHD) setting is set to Off.

This setting is set to Auto automatically when the HDMI Control(RIHD) setting is set to On for the first time.

If you set Audio Return Channel to Auto, the Audio Selector settings of the TV/CD input selector will be automatically switched to ARC ( page 57).

LipSync Off On

This function allows the AV receiver to automatically correct any delay between the video and the audio, based on the data from the connected monitor.

Note

This function works only if your HDMI-compatible TV supports HDMI Lip Sync.

InstaPrevue These settings apply to InstaPrevue of the Home menu ( page 40) and specify the preview display of HDMI video streams.

Sub Window Multi:

Displays preview thumbnails all at once. Single:

Displays preview thumbnails one-by-one. With this setting, you can set the number of preview thumbnails displayed.

Position (with Sub Window set to Multi)

Top, Bottom, Left, Right (with Sub Window set to Single)

Upper Left, Upper Right, Lower Left, Lower Right With this setting, you can set the position of preview thumbnails on the TV screen.

Note

Depending on video signals, the picture may not be properly rendered on the preview thumbnails of InstaPrevue.

Auto Standby

Auto Standby Off On

When Auto Standby is set to On, the ASb indicator lights and the AV receiver will automatically enter standby mode if there is no operation for 30 minutes with no audio and no video signal input. Auto Standby will appear on the AV receivers display and OSD 30 seconds before the Auto Standby comes on.

Note

Set to On, the Auto Standby function may activate itself during playback with some sources.

The Auto Standby function does not work when Zone 2 is on.

After changing the settings of the HDMI Control(RIHD), HDMI Through or Audio Return Channel, turn off the power on all connected pieces of equipment and then turn them on again. Refer to the users manuals for all connected pieces of equipment.

Advanced Operations

En-62

Network

This section explains how to configure the AV receivers network settings manually. If your routers DHCP server is enabled, you dont need to change any of these settings, as the AV receiver is set to use DHCP to configure itself automatically by default (i.e., DHCP is set to Enable). If, however, your routers DHCP server is disabled (youre for example using static IP), youll need to configure these settings yourself, in which case, a knowledge of Ethernet networking is essential. Whats DHCP? DHCP (Dynamic Host Configuration Protocol) is used by routers, computers, the AV receiver, and other devices to automatically configure themselves on a network. Whats DNS? The DNS (Domain Name System) translates domain names into IP addresses. For example, when you enter a domain name such as www.onkyousa.com in your Web browser, before accessing the site, your browser uses DNS to translate this into an IP address, in this case 63.148.251.142.

MAC Address This is the AV receivers MAC (Media Access Control) address. This address cannot be changed.

DHCP Enable Disable

This setting determines whether or not the AV receiver uses DHCP to automatically configure its IP Address, Subnet Mask, Gateway, and DNS Server settings.

Note

If you select Disable, you must configure the IP Address, Subnet Mask, Gateway, and DNS Server settings yourself.

IP Address Class A:

10.0.0.0 to 10.255.255.255 Class B:

172.16.0.0 to 172.31.255.255 Class C:

192.168.0.0 to 192.168.255.255 Enter a static IP address provided by your Internet Service Provider (ISP). Most routers use Class C IP addresses.

Subnet Mask Enter the subnet mask address provided by your ISP (typically 255.255.255.0).

Gateway Enter the gateway address provided by your ISP.

DNS Server Enter the DNS server address provided by your ISP.

Proxy URL To use a Web proxy, enter its URL here.

Proxy Port If youre using a Web proxy, enter a proxy port number here.

Network Standby On Off

This setting enables or disables control over the network. When enabled, the NET indicator will be dimly-lit while the AV receiver is in standby mode. Note that the indicator may not light under certain conditions ( page 47).

Note

When set to On, the power consumption slightly increases in standby mode.

Update Notice Enable Disable

When this setting is enabled, you will be notified if a firmware update via network is available.

Note

Selecting Never Remind me on the notification window will switch this setting to Disable ( page 19).

For details on the update notification, see If the Firmware Update Available window appears. ( page 19).

Initial Setup

If you skipped the initial setup wizard, for example on first-time use, you can reaccess it from here. See Initial Setup ( page 20).

After modifying the network settings, you must confirm the changes by executing Save.

Advanced Operations

En-63

Main Menu Remote Controller Setup

Remote ID

Remote ID 1, 2, or 3

When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from other components, you can change its remote ID from 1, to 2 or 3.

Note

If you do change the AV receivers remote ID, be sure to change the remote controller to the same ID (see below), otherwise, you wont be able to control it with the remote controller.

Changing the remote controllers ID

Remote Mode Setup

See Looking up for Remote Control Codes ( page 68).

Main Menu Lock Setup

With this preference, you can protect your settings by locking the setup menus.

Setup Locked Unlocked

When Locked is selected, the setup menus will be locked and you cannot change any setting.

Remote Controller Setup

1 While holding down RECEIVER, press and hold down Q SETUP until the remote indicator lights (about 3 seconds).

2 Use the number buttons to enter ID 1, 2, or 3. The remote indicator flashes twice.

1 2 3 4 5 Setup

Lock Setup

1 2 3 4 5 Setup

Advanced Operations

En-64

Zone 2 In addition to the main listening room, you can also enjoy playback in another room, or as we call Zone 2. And, you can select a different source for each room.

There are two ways you can connect Zone speakers: 1. Connect them directly to the AV receiver. 2. Connect them to an additional amplifier.

Connecting the Zone Speakers Directly to the AV receiver

This setup allows you to select different sources for Main room and Zone 2. This is called Powered Zone, as the Zone 2 speakers are powered by the AV receiver.

Note

With this setup, the volume of Zone 2 is controlled by the AV receiver.

When Powered Zone 2 is used, playback in the main room is reduced to 5.1 channels.

Connecting the Zone Speakers to an Additional Amplifier

This setup allows 7.1-channel playback in your main listening room and 2-channel stereo playback in Zone 2.

Note

The volume of Zone 2 must be set on the Zone 2 amplifier.

Making Zone 2 Connections

To use this setup, you must activate the Powered Zone 2 setting ( page 50).

L R

Main room

TV

AV receiver

Zone 2

IN

R L

Main room

TV

Zone 2

AV receiver

Receiver/ integrated amp

Advanced Operations

En-65

Operating on the AV receiver

Operating on the remote controller To control Zone 2, you must press ZONE2 on the remote controller first.

Adjusting the Volume for Zone 2

Operating on the remote controller

Operating on the AV receiver

If your Zone 2 speakers are connected to a receiver or integrated amplifier in Zone 2, use its volume control to adjust the volume.

Muting Zone 2

Operating on the remote controller

Tip

To unmute, press ZONE2 followed by MUTING again. Zone can also be unmuted by adjusting the volume.

Note

Only analog input sources are output from the ZONE 2 LINE OUT jacks and ZONE 2 L/R terminals. Digital input sources are not output. If no sound is heard when an input source is selected, verify that the source is connected to an analog input.

You cannot select different AM or FM radio stations for your main room and Zone 2. The same AM/FM radio station will be heard in each room. Namely, if you have selected an FM station for the main room, that station will also be output in Zone 2.

When you have selected NET or USB as input selector, the last selector selected will be set for Main room and Zone 2.

When Zone 2 is activated and its input selector is selected, the power consumption of standby mode slightly increases.

While Zone 2 is on, u functions will not work. When setting the AV receiver to standby mode while Zone 2 is

active, the Z2 indicator is dimly lit. AUX, EXTRA1 and EXTRA2 cannot be selected as input

sources for Zone 2. When AUX, EXTRA1 or EXTRA2 is the input source of

Main room and Zone 2 is set to share the same source, no sound will be output from Zone 2.

Controlling Zone 2 Components

1 To turn on Zone 2 and select an input source, press ZONE 2 followed by an input selector button within 8 seconds. Zone 2 turns on, the Z2 indicator lights on the AV receivers display.

To select the same source as the main rooms, press ZONE 2 twice. Z2 Sel: Source appears on the AV receivers display.

2 To turn off Zone 2, press OFF. The zone is turned off.

ZONE 2 OFF MASTER VOLUME Input selector buttons

8RECEIVER ZONE2

INPUT SELECTOR

VOLq/w

MUTING

1 Press ZONE2, then point the remote controller at the AV receiver and press 8RECEIVER. Zone 2 turns on, the Z2 indicator lights on the AV receivers display.

2 To select an input source for Zone 2, press ZONE2, followed by an INPUT SELECTOR button.

3 To turn off Zone 2, press ZONE2, followed by 8RECEIVER. The zone is turned off.

1 Press ZONE2.

2 Use VOL q/w.

1 Press ZONE 2 (the Z2 indicator on the AV receivers display flash).

2 Use MASTER VOLUME control within 8 seconds.

1 Press ZONE2 followed by MUTING.

En-66

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock

RI Dock

With the RI Dock, you can easily play the music of your iPod/iPhone, or watch the slideshows and videos of your iPod/iPhone on a TV. In addition, the on-screen display (OSD) allows you to view, navigate, and select your iPod/iPhone models contents on your TV, and with the supplied remote controller, you can control your iPod/iPhone from the comfort of your sofa. You can even use the AV receivers remote controller to operate your iPod/iPhone.

Note

Enter the appropriate remote control code before using the AV receivers remote controller for the first time ( page 69).

Connect the RI Dock to the AV receiver with an u cable ( page 17).

Set the RI Docks RI MODE switch to HDD or HDD/DOCK.

Set the AV receivers Input Display to DOCK ( page 41).

System Function

System On When you turn on the AV receiver, the RI Dock and iPod/iPhone turn on automatically. In addition, when RI Dock and iPod/iPhone are on, the AV receiver can be turned on by pressing 8SOURCE.

Auto Power On If you press the remote controllers 1 (Playback) while the AV receiver is on standby, the AV receiver will automatically turn on, select your iPod/iPhone as the input source, and your iPod/iPhone will start playback.

Direct Change If you start iPod/iPhone playback while listening to another input source, the AV receiver will automatically switch to the input to which the RI Dock is connected.

Other Remote Operations You can use the remote controller that came with the AV receiver to control other iPod/iPhone functions. The available functionality depends on the AV receiver.

Note

If you use your iPod/iPhone with any other accessories, iPod/iPhone playback detection may not work.

The System On function may not work depending on the RI Dock.

iPod Alarm If you use the Alarm function on your iPod to start playback, the AV receiver will turn on at the specified time and select your iPod as the input source automatically.

Note

This linked operation wont work while a video is being played or when the sound set for the alarm is a built-in sound (Beep).

This linked operation wont work with models on which music files cannot be used to set the alarm sound.

Using the Onkyo Dock

The Dock is sold separately. Models sold are different depending on the region. For the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod/iPhone with the latest software, available from the Apple web site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock.

Depending on your iPod/iPhone model and generation, some of the linked operations may not be available.

Operating Notes Use the AV receivers volume control to adjust the playback

volume. While your iPod/iPhone is inserted in the RI Dock, its volume

control has no effect. If you do adjust the volume control on your iPod/iPhone while

its inserted in the RI Dock, be careful that its not set too loud before you reconnect your headphones.

Controlling Other Components

En-67

By pressing the REMOTE MODE button thats been programmed with the remote control code for your Dock, you can control your iPod/iPhone in the Dock with the buttons described further in this section. See Entering Remote Control Codes for details on entering a remote control code ( page 69). See the Docks instruction manual for more information.

RI Dock

Set the RI Docks RI MODE switch to HDD or HDD/DOCK.

8SOURCE may not work with a remote control code (without u). In this case, make an u connection and enter the remote control code 81993 (with u).

With the RI Control Make an u connection and enter the remote control code 81993 (with u). Set the AV receivers Input Display to DOCK

( page 41).

Without the RI Control You must enter the remote control code 82990 first ( page 70).

u Dock operation

With some iPod/iPhone models, generations and RI Docks, certain buttons may not work as expected.

For detailed operation of iPod/iPhone, please refer to the instruction manual of the RI Dock.

*1 TOP MENU works as the mode button when used with the DS-A2 RI Dock.

*2 This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or off. Also, your iPod/iPhone may not respond the first time you press this button, in which case you should press it again. This is because the remote controller transmits the On and Standby commands alternately, so if your iPod/iPhone is already on, it will remain on when the remote controller transmits the On command. Similarly, if your iPod/iPhone is already off, it will remain off when the remote controller transmits the Off command.

*3 DISPLAY turns on the backlight for a few seconds. *4 Resume mode

With the Resume function, you can resume playback of the song that was playing when you removed your iPod/iPhone from the Onkyo DS-A2 RI Dock.

Controlling Your iPod/iPhone

b

a

g

i

h

k

j

d

f

e

c

Press the appropriate REMOTE MODE button first.

Available buttons

a TOP MENU*1 e 8SOURCE*2

b q/w/e/r, ENTER f DISPLAY*3

PLAYLIST e/r g MUTING

c 1, 3, 2, 5, 4, 7, 6

h ALBUM +/

i VOL q/w d REPEAT j MENU

RANDOM k MODE*4

Controlling Other Components

En-68

Controlling Other Components You can use the AV receivers remote controller to control your other AV components. This section explains how to enter the remote control code for a component that you want to control: DVD, TV, CD, etc.

The following REMOTE MODE buttons are preprogrammed with remote control codes for controlling the components listed. You do not need to enter a remote control code to control these components. For details on controlling these components, see the indicated pages.

You can look up for an appropriate remote control code from the on-screen menu.

Note

This can only be carried out using the on-screen menu.

Preprogrammed Remote Control Codes

BD/DVD Onkyo Blu-ray Disc player ( page 71) TV/CD Onkyo CD player ( page 70)

Looking up for Remote Control Codes

1 Press RECEIVER followed by HOME.

2 Use e/r to select Setup, and then press ENTER.

3 Use q/w to select Remote Controller Setup, and then press ENTER.

4 Use q/w to select Remote Mode Setup, and then press ENTER.

5 Use q/w to select a remote mode, and then press ENTER. The menu of category selection appears.

6 Use q/w to select a category, and then press ENTER. The keyboard screen for brand name input appears.

7 Use q/w/e/r to select a character, and then press ENTER. Repeat this step for the first three characters of the brand name. When you have entered the 3rd character, select Search and press ENTER. A list of brand names is retrieved. If the desired brand name is not found:

Use r to select Not Listed, and then press ENTER. The keyboard screen for brand name input appears.

8 Use q/w to select a brand, and then press ENTER. A remote control code with its instructions are displayed. Follow the procedure.

9 If you can control the component, use q/w to select OK, and then press ENTER. The on-screen menu returns to the Remote Mode Setup front screen.

If you cannot control the component, use q/w to select Try Next Code and press ENTER. The next code is displayed.

Controlling Other Components

En-69

Youll need to enter a code for each component that you want to control.

Note

Though the provided remote control codes are correct at the time of release, they are subject to change.

You can change the configuration of colored buttons, with which REMOTE MODE buttons are preset.

Tip

To reset the REMOTE MODE buttons to their default settings, see Resetting the REMOTE MODE Buttons ( page 70).

Note

If any other button than the colored buttons is pressed, the operation will be cancelled.

This operation cannot be done while the AV receiver is in Receiver mode or when ZONE 2 is active.

Entering Remote Control Codes

1 Look up the appropriate remote control code in the separate Remote Control Codes list. The codes are organized by category (e.g., DVD player, TV, etc.).

2 While holding down the REMOTE MODE button to which you want to assign a code, press and hold down DISPLAY (about 3 seconds). The remote indicator lights.

Note

Remote control codes cannot be entered for RECEIVER and the multi zone button.

Only TV remote control codes can be entered for TV. Except for RECEIVER, TV, and the multi zone button,

remote control codes from any category can be assigned for the REMOTE MODE buttons. However, these buttons also work as input selector buttons ( page 22), so choose a REMOTE MODE button that corresponds with the input to which you connect your component. For example, if you connect your CD player to the CD input, choose TV/CD when entering its remote control code.

3 Within 30 seconds, use the number buttons to enter the 5-digit remote control code. The remote indicator flashes twice. If the remote control code is not entered successfully, the remote indicator will flash once slowly.

Remapping Colored Buttons

1 While holding down the REMOTE MODE button that you want to program, press and hold down A (Red) until the remote indicator lights (about 3 seconds). You can only change colored buttons for components whose codes belong to categories of the Remote Control Codes list (BD/DVD player, TV, cable set-top box, etc).

2 Within 30 seconds, press the colored buttons in the order that you want to reassign them. The button presses are assigned to each button from left to right. The remote indicator flashes twice, indicating that the sequence has been successfully assigned. If the sequence is not successfully assigned, the remote indicator will flash once slowly.

Controlling Other Components

En-70

Onkyo components that are connected via u are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example.

Controlling Onkyo components without u If you want to control an Onkyo component by pointing the remote controller directly at it, or you want to control an Onkyo component thats not connected via u, use the following remote control codes:

30627: Onkyo DVD player without u

71817: Onkyo CD player without u

32900/33100/33500: Onkyo Blu-ray Disc player

32901/33104/33504: Onkyo HD DVD player

70868: Onkyo MD recorder without u

71323: Onkyo CD recorder without u

82990: Onkyo Dock without u

You can reset a REMOTE MODE button to its default remote control code.

You can reset the remote controller to its default settings.

By pressing the REMOTE MODE button thats been programmed with the remote control code for your component, you can control your component as described below. For details on entering a remote control code for other components, see Entering Remote Control Codes ( page 69).

Controlling a TV

TV is preprogrammed with the remote control code for controlling a TV that supports the p*1 (limited to some models). The TV must be able to receive remote control commands via p and be connected to the AV receiver via HDMI. If controlling your TV via p doesnt work very well, program your TVs remote control code into TV and use the TV remote mode to control your TV. Use the following remote control codes:

11807/13100/13500: TV with p

Controlling Apple TV

By programming the supplied remote controller with the appropriate remote control code, you can use it to operate your Apple TV. Use the following remote control codes:

02615: Apple TV

Remote Control Codes for Onkyo Components Connected via RI

1 Make sure the Onkyo component is connected with an u cable and an analog audio cable (RCA). See Connecting Onkyo RI Components for details ( page 17).

2 Enter the appropriate remote control code for a REMOTE MODE button, by referring to the previous section.

42157: Onkyo cassette tape deck with u

81993: Onkyo Dock with u

3 Press the REMOTE MODE button, point the remote controller at the AV receiver, and operate the component.

Resetting the REMOTE MODE Buttons

1 While holding down the REMOTE MODE button that you want to reset, press and hold down HOME until the remote indicator lights (about 3 seconds).

2 Within 30 seconds, press the REMOTE MODE button again. The remote indicator flashes twice, indicating that the button has been reset. Each REMOTE MODE button is preprogrammed with a remote control code. When a button is reset, its preprogrammed code is restored.

Resetting the Remote Controller

1 While holding down RECEIVER, press and hold down HOME until the remote indicator lights (about 3 seconds).

2 Within 30 seconds, press RECEIVER again. The remote indicator flashes twice, indicating that the remote controller has been reset.

Controlling Other Components

Controlling Other Components

En-71

Controlling MHL-Enabled Mobile Device

By programming the supplied remote controller with the appropriate remote control code, you can use it to operate your MHL-enabled mobile device. Connect your MHL-enabled mobile device to the AUX INPUT MHL jack. We advise you to program the remote control code on the AUX button. Use the following remote control codes:

33101: MHL-enabled mobile device

Note

With some mobile devices, reliable operation cannot be guaranteed.

Controlling a Blu-ray Disc/DVD Player, HD DVD Player or DVD Recorder

BD/DVD is preprogrammed with the remote control code for controlling a component that supports the p*1 (limited to some models). The component must be able to receive remote control commands via p and be connected to the AV receiver via HDMI. Use the following remote control codes:

32910/33101/33501/31612: Blu-ray Disc/DVD player with p

*1 The p supported by the AV receiver is the CEC system control function of the HDMI standard.

TV operation

Blu-ray Disc player / HD DVD player operation

h

l

m

n

o

i

k

j

g

c

b

d

a

e

f

Press the appropriate REMOTE MODE button first. Available buttons

a 8, INPUT, TV VOL q/w, MUTING

g Number: 1 to 9, 0

Number: +10*1

b GUIDE i DISPLAY

c q/w/e/r ENTER

k CH +/

l PREV CH

d SETUP m RETURN

e 1, 3, 2, 5, 4, 7, 6*1

n AUDIO*1

o CLR

f A (Red)*1

B (Green)*1

C (Yellow)*1

D (Blue)*1

Available buttons

b TOP MENU h 8SOURCE

c q/w/e/r ENTER

i DISPLAY

j MUTING

d SETUP k CH +/

e 1, 3, 2, 5, 4, 7, 6

DISC +/

l MENU

f A (Red) m RETURN

B (Green) n AUDIO*1

C (Yellow) o CLR

D (Blue)

g Number: 1 to 9, 0

Number: +10*1

Controlling Other Components

En-72

DVD player / DVD recorder operation

VCR/PVR operation

Cassette tape deck operation

Satellite receiver / Cable receiver operation

CD player / CD recorder / MD recorder operation

Note

With some components, certain buttons may not work as expected, and some may not work at all.

See Controlling Your iPod/iPhone about the operation of iPod/iPhone ( page 67).

*1 The p function is not supported. The p supported by the AV receiver is the CEC system control function of the HDMI standard.

h

l

m

n

o

i

k

j

g

c

b

d

e

f

Press the appropriate REMOTE MODE button first. Available buttons

b TOP MENU h 8SOURCE

c q/w/e/r ENTER

i DISPLAY

j MUTING

d SETUP k CH +/

e 1, 3, 2, 5, 4, 7, 6

DISC +/

l MENU

f A (Red)*1 m RETURN

B (Green) n AUDIO*1

C (Yellow)*1 o CLR

D (Blue)*1

g Number: 1 to 9, 0

Number: +10*1

Available buttons

b GUIDE h 8SOURCE

c q/w/e/r ENTER

i DISPLAY

j MUTING

d SETUP k CH +/

e 1, 3, 2, 5, 4, 7, 6

l PREV CH

m RETURN

g Number: 1 to 9, 0 o CLR

Number: +10

Available buttons

e 1, t (Reverse Playback), 2, 5, 4, 7, 6

h 8SOURCE

j MUTING

Available buttons

b GUIDE g Number: 1 to 9, 0

c q/w/e/r ENTER

Number: +10

h 8SOURCE

d SETUP i DISPLAY

e 1, 3, 2, 5, 4, 7, 6

j MUTING

k CH +/

f A (Red) l PREV CH

B (Green) m RETURN

C (Yellow) n AUDIO

D (Blue) o CLR

Available buttons

c q/w/e/r ENTER

g Number: 1 to 9, 0

Number: +10

d SETUP h 8SOURCE

e 1, 3, 2, 5, 4, 7, 6

i DISPLAY

j MUTING

f SEARCH k DISC +/

REPEAT o CLR

RANDOM

MODE

En-73

Appendix

Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you cant resolve the issue yourself, contact your Onkyo dealer.

Cant turn on the AV receiver

The AV receiver turns off unexpectedly

The AV receiver turns off and after restoring the power, it turns off again

Theres no sound, or its very quiet

If you cant resolve the issue yourself, try resetting the AV receiver before contacting your Onkyo dealer. To reset the AV receiver to its factory defaults, turn it on and, while holding down CBL/SAT, press 8ON/STANDBY. Clear will appear on the AV receivers display and the AV receiver will enter standby mode.

Note that resetting the AV receiver will delete your radio presets and custom settings.

To reset the remote controller to its factory defaults, while holding down RECEIVER, press and hold down HOME until the remote indicator lights (about 3 seconds). Within 30 seconds, press RECEIVER again.

HOME

RECEIVER

Remote indicator

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receivers display when changing settings.

Power

Make sure that the power cord is properly plugged into the wall outlet.

Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again.

The AV receiver will automatically enter standby mode when Auto Standby has been set and launches.

61

The protection circuit has been activated. Remove the power cord from the wall outlet immediately. Make sure that all speaker cables and input sources are properly connected, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and turn the power on. If the AV receiver turns off again, unplug the power cord and contact your Onkyo dealer. Caution: If CHECK SP WIRE appears on the AV receivers display, the speaker cables may be shorting.

12

WARNING If smoke, smell or abnormal noise is produced by the AV receiver, unplug the power cord from the wall outlet immediately and contact your Onkyo dealer.

Audio

Make sure that the digital input source is selected properly.

49

Make sure that all audio connecting plugs are pushed in all the way.

14

Make sure that the inputs and outputs of all components are connected properly.

15-17

Make sure that the polarity of the speaker cables is correct, and that the bare wires are in contact with the metal part of each speaker terminal.

12

Make sure that the input source is properly selected. 22

Make sure that the speaker cables are not shorting. 12

Check the volume. The AV receiver is designed for home theater enjoyment. It has a wide volume range, allowing precise adjustment.

If the MUTING indicator is flashing on the AV receivers display, press the remote controllers MUTING button to unmute the AV receiver.

42

While a pair of headphones is connected to the PHONES jack, no sound is output from the speakers.

42

If theres no sound from a DVD player connected to an HDMI IN, check the DVD players output settings, and be sure to select a supported audio format.

Check the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off.

With some DVD-Video discs, you need to select an audio output format from a menu.

If your turntable uses an MC cartridge, you must connect an MC head amp, or an MC transformer.

Make sure that none of the connecting cables are bent, twisted, or damaged.

Not all listening modes use all speakers. 35

Specify the speaker distances and adjust the individual speaker levels.

51

Make sure that the speaker setup microphone is not still connected.

Appendix

En-74

Only the front speakers produce sound

Only the center speaker produces sound

The surround speakers produce no sound

The center speaker produces no sound

The front high and surround back speakers produce no sound

The subwoofer produces no sound

Theres no sound with a certain signal format

Cant get 6.1/7.1 playback

The speaker volume cannot be set as required

Noise can be heard

The Late Night function doesnt work

About DTS signals

The beginning of audio received by an HDMI IN cant be heard

If the input signal format is set to PCM or DTS. Set it to Off.

57

When the Stereo or Mono listening mode is selected, only the front speakers and subwoofer produce sound.

38

Check the Speaker Configuration. 50

If you use the Dolby Pro Logic IIx Movie, Dolby Pro Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker.

Make sure the speakers are configured correctly. 50

When the T-D (Theater-Dimensional), Stereo or Mono listening mode is selected, the surround speakers produce no sound.

Depending on the source and current listening mode, not much sound may be produced by the surround speakers. Try selecting another listening mode.

35

Make sure the speakers are configured correctly. 50

When the Stereo or Mono listening mode is selected, the center speaker produces no sound.

Make sure the speakers are configured correctly. 50

Depending on the current listening mode, no sound may be produced by the front high and surround back speakers. Select another listening mode.

36

Depending on the sources, the sound produced by the front high and surround back speakers may be weak.

Make sure the speakers are configured correctly. 50

When Powered Zone 2 is used, playback in the main room is reduced to 5.1channels and the front high and surround back speakers produce no sound.

When you play source material that contains no information in the LFE channel, the subwoofer produces no sound.

Make sure the speakers are configured correctly. 50

Check the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off.

With some DVD-Video discs, you need to select an audio output format from a menu.

Depending on the input signal, some listening modes cannot be selected.

35-39

If no surround back speakers and front high speakers are connected, or the Zone 2 speakers are being used, 6.1/7.1 playback is not possible.

Depending on the number of connected speakers, it is not always possible to select all of the listening modes.

35-39

Check to see if a maximum volume has been set. 59

If the volume level of each individual speaker has been adjusted to high positive values, then the maximum master volume possible may be reduced. Note that the individual speaker volume levels are set automatically after the Audyssey 2EQ Room Correction and Speaker Setup has been performed.

32, 51

Using cable ties to bundle audio cables with power cords, speaker cables, and the like may degrade the audio performance, so refrain from doing it.

An audio cable may be picking up interference. Try repositioning your cables.

Make sure the source material is Dolby Digital, Dolby Digital Plus, and Dolby TrueHD.

45

Make sure that the TrueHD Loudness Management setting is not set to Off. The Late Night function doesnt work when this setting is disabled.

53

When DTS program material ends and the DTS bitstream stops, the AV receiver remains in DTS listening mode and the dts indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, you may not hear any sound because the AV receiver does not switch formats immediately. In such case, you should stop your player for about three seconds and then resume playback.

With some CD and LD players, you wont be able to playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesnt recognize it as a genuine DTS signal. In such cases, you may hear noise.

Playing DTS program material, using the pause, fast forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.

Since it takes longer to identify the format of an HDMI signal than it does for other digital audio signals, audio output may not start immediately.

Appendix

En-75

Theres no picture

Theres no picture from a source connected to an HDMI IN

The on-screen menus dont appear

The on-screen display does not appear

Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesnt light

The remote controller doesnt work

Cant control other components

Video

Make sure that all video connecting plugs are pushed in all the way.

14

Make sure that each video component is properly connected.

15, 16

If your TV is connected to the HDMI output(s), select - - - - - in the HDMI Input setup to watch composite video, and component video sources.

48

If the video source is connected to a component video input, you must assign that input to an input selector, and your TV must be connected to either the HDMI output(s) or COMPONENT VIDEO OUT.

16, 49

If the video source is connected to a composite video input, your TV must be connected to the HDMI output(s) or the corresponding composite video output.

16

If the video source is connected to an HDMI input, you must assign that input to an input selector, and your TV must be connected to the HDMI output(s).

15, 48

On your TV, make sure that the video input to which the AV receiver is connected is selected.

Reliable operation with an HDMI-to-DVI adapter is not guaranteed. In addition, video signals from a PC are not guaranteed.

88

When the resolution is set to any resolution not supported by the TV, no video is output from the HDMI outputs.

48

If the message Resolution Error appears on the AV receivers display, this indicates that your TV does not support the current video resolution and you need to select another resolution on your DVD player.

On your TV, make sure that the video input to which the AV receiver is connected is selected.

When the AV receiver is not connected to a TV via HDMI OUT MAIN, on-screen menus are not displayed.

Depending on the input signal, the on-screen display may not appear when the input signal from HDMI IN is output to a device connected to HDMI OUT MAIN.

43

Tuner

Relocate your antenna.

Move the AV receiver away from your TV or computer.

Listen to the station in mono. 30

When listening to an AM station, operating the remote controller may cause noise.

Passing cars and airplanes can cause interference.

Concrete walls weaken radio signals.

If nothing improves the reception, install an outdoor antenna.

Remote Controller

Before operating this unit, be sure to press RECEIVER.

Make sure that the batteries are installed with the correct polarity.

4

Install new batteries. Dont mix different types of batteries, or old and new batteries.

4

Make sure that the remote controller is not too far away from the AV receiver, and that theres no obstruction between the remote controller and the AV receivers remote control sensor.

4

Make sure that the AV receiver is not subjected to direct sunshine or inverter-type fluorescent lights. Relocate if necessary.

If the AV receiver is installed in a rack or cabinet with colored-glass doors, the remote controller may not work reliably when the doors are closed.

Make sure youve selected the correct remote controller mode.

10, 70

When using the remote controller to control other manufacturers AV components, some buttons may not work as expected.

Make sure youve entered the correct remote control code.

69

Make sure to set the same ID on both the AV receiver and remote controller.

63

If its an Onkyo component, make sure that the u cable and analog audio cable are connected properly. Connecting only an u cable wont be enough.

17

Make sure youve selected the correct remote controller mode.

10, 70

If youve connected an cassette tape deck to the TV/CD IN jack, or an RI Dock to the TV/CD IN or GAME IN jacks, for the remote controller to work properly, you must set the input display appropriately.

41

If you cannot operate it, you will need to enter the appropriate remote control code.

68

To control another manufacturers component, point the remote controller at that component.

69

To control an Onkyo component thats connected via u, point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first.

70

To control an Onkyo component thats not connected via u, point the remote controller at the component. Be sure to enter the appropriate remote control code first.

70

The entered remote control code may not be correct. If more than one code is listed, try each one.

Appendix

En-76

Theres no sound

Theres no video

The AV receivers remote controller doesnt control my iPod/iPhone

The AV receiver unexpectedly selects my iPod/iPhone as the input source

iPod/iPhone doesnt work properly

Theres no sound

The Zone 2 speakers produce no sound

Cant access the server or Internet radio

Playback stops while listening to music files on the server

Cant connect to the AV receiver from a Web browser

Cant access the music files on a USB device

RI Dock for iPod/iPhone

Make sure your iPod/iPhone is actually playing.

Make sure your iPod/iPhone is properly inserted in the Dock.

Make sure the AV receiver is turned on, the correct input source is selected, and the volume is turned up.

Make sure the plugs are pushed in all the way.

Try resetting your iPod/iPhone.

Make sure that your iPod/iPhone models TV OUT setting is set to On.

Make sure the correct input is selected on your TV or the AV receiver.

Some versions of the iPod/iPhone do not output video.

Make sure your iPod/iPhone is properly inserted in the Dock. If your iPod/iPhone is in a case, it may not connect properly to the Dock. Always remove your iPod/iPhone from the case before inserting it into the Dock.

The iPod/iPhone cannot be operated while its displaying the Apple logo.

Make sure youve selected the right remote mode. 67

When you use the AV receivers remote controller, point it toward your AV receiver.

If you still cant control your iPod/iPhone, start playback by pressing your iPod/iPhone models Play button. Remote operation should then be possible.

Try resetting your iPod/iPhone.

Depending on your iPod/iPhone, some buttons may not work as expected.

Always pause iPod/iPhone playback before selecting a different input source. If playback is not paused, the Direct Change function may select your iPod/iPhone as the input source by mistake during the transition between tracks.

Try reconnecting your iPod/iPhone.

Zone 2

Only components connected to analog inputs can be played in Zone 2.

Powered Zone 2 cannot be used if Speakers Type (Front) is set to Bi-Amp.

50

Music Server and Internet Radio

Check the network connection between the AV receiver and your router or switch.

89

Make sure that your modem and router are properly connected, and make sure they are both turned on.

Make sure the server is up and running and compatible with the AV receiver.

90

Check the Network settings. 62

Make sure your server is compatible with the AV receiver.

90

If you download or copy large files on your computer, playback may be interrupted. Try closing any unused programs, use a more powerful computer, or use a dedicated server.

If the server is serving large music files to several networked devices simultaneously, the network may become overloaded and playback may be interrupted. Reduce the number of playback devices on the network, upgrade your network, or use a switch instead of a hub.

If youre using DHCP, your router may not always allocate the same IP address to the AV receiver, so if you find that you cant connect to a server or Internet radio station, recheck the AV receivers IP address on the Network screen.

62

Check the Network settings. 62

USB Device Playback

Make sure the USB device is plugged in properly.

The AV receiver supports USB devices that support the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class.

90

USB memory devices with security functions cannot be played.

Appendix

En-77

Standby power consumption

The sound changes when I connect my headphones

The speaker distance cannot be set as required

How do I change the language of a multiplex source

The u functions dont work

The functions System On/Auto Power On and Direct Change dont work for components connected via u

When performing Automatic Speaker Setup, the measurement fails and the message Ambient noise is too high. is displayed.

The following settings can be made for the composite video inputs You must use the buttons on the unit to make these settings. On the AV receiver, press the input selector for the input source that you want to set and the SETUP button simultaneously. While holding down the input selector button, press SETUP until Video ATT :On appears on the AV receivers display. Then, release both buttons. To turn the setting off, repeat the above process so that Video ATT :Off appears on the AV receivers display, and release the buttons.

Video Attenuation This setting can be made for the BD/DVD, CBL/SAT, GAME, PC or USB input. If you have a game console connected to the composite video input, and the picture isnt very clear, you can attenuate the gain. Video ATT :Off: (default). Video ATT :On: Gain is reduced by 2 dB.

If the picture on your TV/monitor connected to the HDMI output(s) is unstable, try switching the DeepColor function off To turn off the DeepColor function, simultaneously press the GAME and 8ON/STANDBY buttons on the AV receiver. While holding down GAME, press

8ON/STANDBY until Deep Color:Off appears on the AV receivers display. Then, release both buttons. To reactivate the DeepColor function, repeat the above process until Deep Color:On appears on the AV receivers display and release the buttons.

Others

In the following cases, the power consumption in standby mode may reach up to a maximum of 8.3 W:

The HDMI Control(RIHD) setting is set to On. (Depending on the TV status, the AV receiver will enter standby mode as usual.)

The HDMI Through setting is set to other than Off.

The Network Standby setting is set to On.

60, 62

If an MHL-enabled mobile device is connected to the AUX (front) input, the power consumption in standby mode will increase.

15

When a pair of headphones is connected, the listening mode is set to Stereo, unless its already set to Stereo, Mono, or Direct.

The values entered may be automatically adjusted with values best-suited for your home theater.

Use the Multiplex setting in the Audio Adjust menu to select Main or Sub.

52

To use u, you must make an u connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally.

17

While Zone 2 is selected, the u functions dont work.

17

These functions dont work when Zone 2 is turned on.

17

This can be caused by a malfunction in your speaker unit. Check if the unit produces normal sounds.

The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the units malfunction. Before you record important data, make sure that the material will be recorded correctly.

Before disconnecting the power cord from the wall outlet, set the AV receiver to standby.

Appendix

En-78

The AV receiver can upconvert component video and composite video sources for display on a TV connected to the HDMI output(s). However, if the picture quality of the source is poor, upconversion may make the picture worse or disappear altogether. In this case, try the following:

Tip

To by-pass the upconversion, set the Picture Mode setting to Direct ( page 56).

Important Note Regarding Video Playback

1 If the video source is connected to a component video input, connect your TV to COMPONENT VIDEO OUT. If the video source is connected to a composite video input, connect your TV to MONITOR OUT V.

2 On the main menu, select Input/Output Assign, and then select Component Video Input ( page 49).

If the video source is connected to COMPONENT VIDEO IN, select the relevant input selector, and assign it to IN1. If the video source is connected to a composite video input, select the relevant input selector, and assign it to - - - - -.

Appendix

En-79

Firmware Update To update the firmware of the AV receiver, you can choose from the following two methods: update via network, or update via USB storage. Choose the one that best suits your environment. Before proceeding with the update, please read the corresponding explanations carefully.

Update via network You need a wired Internet connection to update the firmware.

Update via USB storage ( page 81) Please prepare a USB storage device such as a USB flash memory stick. You need at least 32 MB of available space to update the firmware.

Note

Check the network connection before updating. Do not touch any cable or device connected to the AV receiver

during the update process. Do not attempt to access the AV receiver from your PC while it

is being updated. Do not shutdown the power of the AV receiver while it is being

updated. The storage media in the USB card reader may not work. If the USB device is partitioned, each section will be treated as an

independent device. If the USB device contains a lot of data, the AV receiver may take

a while to read it. Operation is not guaranteed for all USB devices, which includes

the ability to power them. Onkyo takes no responsibility whatsoever for the loss or damage

of data resulting from the use of a USB device with the AV receiver. Onkyo recommends that you back up your important music files beforehand.

If you connect a USB hard disk drive to the USB port, Onkyo recommends that you use its AC adapter to power it.

USB hubs and USB devices with hub functions are not supported. Do not connect your USB device via a USB hub.

USB devices with security functions are not supported.

The AV receiver allows you to update the firmware using network connection on the rear panel.

Note

Make sure your AV receiver and TV are turned on and an Ethernet cable is connected to the rear panel of the AV receiver.

Never unplug or turn off the AV receiver while it is being updated.

Never plug or unplug an HDMI or Ethernet cable during the update process.

Do not attempt to access the AV receiver from your PC while it is being updated.

Never unplug the power cord during the update process. It takes up to 60 minutes to complete the firmware update. The AV receiver will retain all your settings after the update is

finished.

Before Starting

Set the HDMI Control(RIHD) setting to Off ( page 60).

Turn off the controller device connected via Ethernet cable.

Turn off Multi Zone if this function is present. Stop playback of contents from Internet Radio,

iPod/iPhone, USB or servers, etc.

Limitation of liability The program and accompanying online documentation are furnished to you for use at your own risk. Onkyo will not be liable and you will have no remedy for damages for any claim of any kind whatsoever concerning your use of the program or the accompanying online documentation, regardless of legal theory, and whether arising in tort or contract. In no event will Onkyo be liable to you or any third party for any special, indirect, incidental, or consequential damages of any kind, including, but not limited to, compensation, reimbursement or damages on account of the loss of present or prospective profits, loss of data, or for any other reason whatsoever.

See the Onkyo web site for latest information.

Updating the Firmware via Network

To be continued

Appendix

En-80

Update Procedure Troubleshooting

Case 1: If an error occurs, Error!! *-** is displayed on the AV receivers display. (Alpha-numeric characters on the front display are denoted by asterisks.) Refer to the following table and take appropriate action.

Errors during an update via network

Case 2: If an error occurs during the update process, disconnect then reconnect the AC power cord and try again.

Case 3: If you do not have an Internet connection to the network, please contact Onkyo Support ( page 82).1 Press RECEIVER followed by HOME on the remote

controller. The Home menu appears on the TV screen.

2 Select Firmware Update and press ENTER. Note that the Firmware Update option will be grayed out for a short while after the AV receiver is turned on. Please wait until it becomes operable.

3 Select Update via NET and press ENTER.

Note that this option will not be available if there is no firmware file newer than the currently installed version.

4 Select Update and press ENTER. The update process will begin. During the update process, the on-screen display may disappear depending on the updated program. When this occurs, you can still view the update progress on the AV receivers display. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again.

5 The message Completed! appears on the AV receivers display, indicating that the update has been completed.

6 Turn off the AV receiver using 8ON/STANDBY on the front panel.

Do not use 8RECEIVER on the remote controller. Once turned off, the AV receiver will automatically turn on again. Congratulations! You now have the latest firmware installed on your Onkyo AV receiver.

Error Code Description *-10, *-20 The Ethernet cable was not detected.

Reconnect the cable properly. *-11, *-13, *-21, *-28

Internet connection error. Check the following items: Make sure the IP address, subnet mask,

gateway address, and DNS server are configured properly.

Make sure the router is turned on. Make sure the AV receiver and the router are

connected with an Ethernet cable. Make sure your router is configured properly.

See the instruction manual of the router. If your network allows only one client

connection and there is any other device already connected, the AV receiver will not be able to access the network. Consult your Internet Service Provider (ISP).

If your modem does not function as a router, you will need a router. Depending on your network, you may need to configure the proxy server if necessary. See the document provided by your ISP. If you are still unable to access the Internet, the DNS or proxy server may be temporarily down. Contact your ISP.

Others Retry the update procedure from the beginning. If the error persists, please contact Onkyo Support ( page 82) and provide the error code.

Appendix

En-81

The AV receiver allows you to update the firmware using a USB device.

Note

Never unplug or turn off the AV receiver during the update process.

Never plug or unplug an HDMI cable or a USB device during the update process.

Never unplug the USB storage device containing the firmware file or the AC power cord during the update process.

Do not attempt to access the AV receiver from your PC while it is being updated.

It takes up to 60 minutes to complete the firmware update. The AV receiver will retain all your settings after the update is

finished.

Before Starting

Set the HDMI Control(RIHD) setting to Off ( page 60).

Turn off the controller device connected via Ethernet cable.

Turn off Multi Zone if this function is present. Stop playback of contents from Internet Radio,

iPod/iPhone, USB or servers, etc. If there is any data in the USB device, remove it first.

Update ProcedureUpdating the Firmware via USB

1 Connect a USB device to your PC. If there is any data in the USB device, remove it first.

2 Download the firmware file from the Onkyo web site. The file name is as follows:

ONKAVR****_************.zip

Unzip the downloaded file. The following three files are created:

ONKAVR****_************.of1 ONKAVR****_************.of2 ONKAVR****_************.of3

3 Copy the extracted files to the USB device. Be careful not to copy the zip file.

4 Remove the USB device from your PC and connect it to the USB port on the AV receiver. When the AV receiver has two USB ports, you can use either one.

5 Make sure the AV receiver and TV are turned on. If the AV receiver is in standby mode, press 8ON/STANDBY on the AV receiver to light up the front display.

6 Select the USB input source. Now Initializing... appears on the AV receivers display and then the name of the USB device is displayed. It takes 20 to 30 seconds to recognize the USB device.

7 Press RECEIVER followed by HOME on the remote controller. The Home menu appears on the TV screen.

8 Select Firmware Update and press ENTER.

9 Select Update via USB and press ENTER.

Note that this option will not be available if there is no firmware file newer than the currently installed version.

10 Select Update and press ENTER. The update process will begin. During the update process, the on-screen display may disappear depending on the updated program. When this occurs, you can still view the update progress on the AV receivers display. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again. Do not turn off the AV receiver and do not remove the USB device during the update process.

11 The message Completed! appears on the AV receivers display, indicating that the update has been completed. Remove the USB device.

12 Turn off the AV receiver using 8ON/STANDBY on the front panel.

Do not use 8RECEIVER on the remote controller. Once turned off, the AV receiver will automatically turn on again. Congratulations! You now have the latest firmware installed on your Onkyo AV receiver.

Appendix

En-82

Troubleshooting

Case 1: If an error occurs, Error!! *-** is displayed on the AV receivers display. (Alpha-numeric characters on the front display are denoted by asterisks.) Refer to the following table and take appropriate action.

Errors during an update via USB

Case 2: If an error occurs during the update process, disconnect then reconnect the AC power cord and try again.

Error Code Description *-10, *-20 The USB device was not detected. Make sure

the USB flash memory or USB cable is properly connected to the USB port. If the USB storage device has its own power supply, use it to power the USB device.

*-14 The firmware file was not found in the root folder of the USB device, or the firmware file is for another model. Retry and download the file on the support page of the web site, following the on-site instructions. If the error persists, please contact Onkyo Support and provide the error code.

Others Retry the update procedure from the beginning. If the error persists, please contact Onkyo Support and provide the error code.

China, Hong Kong

Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.onkyochina.com

Asia, Oceania, Middle East, Africa Please contact an Onkyo distributor referring to Onkyo SUPPORT site. http://www.intl.onkyo.com/support/firmware/index.html

Europe

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.eu.onkyo.com/

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN http://www.onkyo.com/

The Americas

The above-mentioned information is subject to change without prior notice. Visit the Onkyo web site for the latest update.

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. For Dealer, Service, Order and all other Business Inquiries: Tel: 201-785-2600 Fax: 201-785-2650 Hours:M-F 9am-5pm ET http://www.us.onkyo.com/

For Product Support Team Only: 1-800-229-1687 Hours:M-F 9am-8pm / Sat-Sun 10am-8pm ET http://www.us.onkyo.com/

Appendix

En-83

Connection Tips and Video Signal Path The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your components. Use the following sections as a guide.

Video components can be connected by using any one of the following video connection formats: composite video, component video, or HDMI, the latter offering the best picture quality.

Tip

To by-pass the upconversion, set the Picture Mode setting to Direct ( page 56).

Monitor Out set to Main or Sub Video input signals flow through the AV receiver as shown, with composite video and component video sources all being upconverted for the HDMI output. Use these settings if you connect either HDMI OUT MAIN or HDMI OUT SUB of the AV receiver to your TV. The composite video and component video outputs pass through their respective input signals as they are.

Note

When composite video and component video sources are upconverted for HDMI OUT SUB, only signals with a resolution of 480i are output and the resolution remains the same. If your TV doesnt support this resolution, there will be no picture ( page 85).

Monitor Out set to Both Video input signals flow through the AV receiver as shown, with composite video and component video sources all being upconverted for both HDMI outputs. Use this setting if you connect both HDMI OUT MAIN and HDMI OUT SUB of the AV receiver to your TV. Note that video signals are output from both HDMI outputs at the resolution supported by both TVs. The composite video and component video outputs pass through their respective input signals as they are.

Note

When Monitor Out is set to Both, the Resolution setting cannot be selected.

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receivers display when changing settings.

Video Connection Formats

IN

MONITOR OUT

Blu-ray Disc/DVD player, etc.

AV receiver

TV, projector, etc.

Composite

Composite

Component

Component

Video Signal Flow Chart

HDMI

HDMI

IN

MONITOR OUT

Blu-ray Disc/DVD player, etc.

AV receiver

TV, projector, etc.

Composite

Composite

Component

Component

Video Signal Flow Chart

HDMI

HDMI

Appendix

En-84

Signal Selection If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, component video, composite video. However, for component video only, regardless of whether a component video signal is actually present, if a component video input is assigned to the input selector, that component video input will be selected. And if no component video input is assigned to the input selector, this will be interpreted as no component video signal being present. In the Signal Selection Example shown below, video signals are present at both the HDMI and composite video inputs. However, the HDMI signal is automatically selected as the source and the video is output by the HDMI outputs.

Audio components can be connected by using any of the following audio connection formats: analog, optical, coaxial, or HDMI. When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa.

If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, digital, analog.

*1 Depends on the Audio TV Out setting ( page 60). *2 This is possible when Audio Return Channel is set to

Auto ( page 61), the TV/CD input selector is selected, and your TV is ARC capable.

Tip

When a signal is input via HDMI and the corresponding input selector is selected, the HDMI indicator lights. In the case of an optical or coaxial connection, the DIGITAL indicator lights. In the case of an analog connection, neither of the HDMI and DIGITAL indicators light.

IN

MONITOR OUT

Blu-ray Disc/DVD player, etc.

AV receiver

TV, projector, etc.

Composite

Composite

Component

Component

Signal Selection Example

HDMI

HDMI

Audio Connection Formats

IN

OUT

Blu-ray Disc/DVD player, etc.

AV receiver

TV, projector, etc.

HDMICoaxial Analog

Audio Signal Flow Chart

HDMI

Optical

*1 *1 *1

*1 *2

Appendix

En-85

The following tables show how video signals at different resolutions are output by the AV receiver.

NTSC

: Output available

s

*1 Supported resolutions: [3840 2160 24/25/30 Hz], [4096 2160 24 Hz] *2 Supported resolutions for HDMI OUT SUB.

Video Resolution Chart

HDMI Component Composite 4K*1 1080p/24 1080p 1080i 720p 480p 480i 1080p 1080i 720p 480p 480i 480i

HDMI 1080p/24 *2

1080p *2

1080i *2

720p *2

480p *2

480i *2

Component 1080p

1080i

720p

480p

480i *2

Composite 480i *2

Output Input

Appendix

En-86

Using an RIHD- compatible TV, Player, or Recorder p, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than p-compatible components cannot be guaranteed.

The following components are p-compatible (As of January 2012).

TV Toshiba TV Sharp TV

Players/Recorders Onkyo and Integra p-compatible players Toshiba players and recorders Sharp players and recorders (only when used together

with Sharp TV)

* Models other than those mentioned above may have some interoperability if compatible with CEC, which is part of the HDMI Standard, but operation cannot be guaranteed.

Note

For proper linked operations, do not connect more p- compatible components than the quantities specified below, to the HDMI input terminal. Blu-ray Disc/DVD players: up to three. Blu-ray Disc/DVD recorders/Digital Video Recorders: up to

three. Cable/Satellite Set-top boxes: up to four.

Do not connect the AV receiver to another AV receiver/AV amplifier via HDMI.

Proper linked operations are not guaranteed when more p-compatible components than the above-mentioned quantities are connected.

For p-compatible TV The following linked operations are enabled by connecting the AV receiver to an p-compatible TV. The AV receiver will enter standby mode when the TV is

set to standby. You can set on the menu screen of the TV to either output

the audio from the speakers connected to the AV receiver, or from the speakers of the TV.

It is possible to output the audio coming from the tuner or auxiliary input of your TV to the speakers of the AV receiver. (A connection such as an optical digital cable or similar is required in addition to the HDMI cable.)

Input to the AV receiver can be selected with the remote controller of the TV.

Operations such as volume adjustment or similar for the AV receiver can be performed from the remote controller of the TV.

For p-compatible players/recorders The following linked operations are enabled by connecting the AV receiver to an p-compatible player/recorder. When playback is started on the player/recorder, AV

receiver will switch to the HDMI input of the player/recorder that is playing back.

Operation of the player/recorder is possible using the remote controller supplied with the AV receiver.

* Depending on the model used, not all operations may be available.

About p-compatible components Operations that can be performed with connection

To be continued

Appendix

En-87

How to connect and setup

1 Confirm the connection and settings. 1. Connect the HDMI OUT MAIN jack to the HDMI

input jack of the TV.

2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable.

Note

When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary ( page 61).

3. Connect the HDMI output of the Blu-ray Disc/DVD player/recorder to the HDMI IN 1 jack of the AV receiver.

Note

It is necessary to assign the HDMI input when connecting the Blu-ray Disc/DVD player/recorder to other jacks ( page 48). Do not assign an HDMI IN to the TV/CD selector at this time, otherwise appropriate CEC (Consumer Electronics Control) operation will not be guaranteed.

Blu-ray Disc/DVD player, etc.

AV receiver

TV, projector, etc.

DIGITAL AUDIO connection (OPTICAL)

HDMI connection

HDMI connection

2 Change each item in the HDMI menu according to the following settings: HDMI Control(RIHD): On Audio Return Channel (ARC): Auto See details of each setting ( pages 60, 61).

3 Confirm the settings. 1. Turn on the power for all connected components. 2. Turn off the power of the TV, and confirm that the

power of the connected components is turned off automatically with the link operation.

3. Turn on the power of the Blu-ray Disc/DVD player/recorder.

4. Start playback on the Blu-ray Disc/DVD player/recorder, and verify the following: The AV receiver automatically turns on, and

selects the input to which the Blu-ray Disc/DVD player/recorder is connected.

The TV automatically turns on, and selects the input to which the AV receiver is connected.

5. Following the operating instructions of the TV, select Use the TV speakers from the menu screen of the TV, and confirm that the audio is output from the speakers of the TV, and not from the speakers connected to the AV receiver.

6. Select Use the speakers connected from the AV receiver from the menu screen of the TV, and confirm that the audio is output from the speakers connected to the AV receiver, and not from the TV speakers.

Note

Perform the above operations when you use the AV receiver for the first time, when the settings of each component are changed, when the main power of each component is turned off, when the power cable is disconnected from the power supply, or when there has been a power outage.

4 Operate with the remote controller. For buttons that can be operated ( page 71).

Note

Audio from DVD-Audio or Super Audio CD may not output from the TV speakers. You will be able to output the audio from the TV speakers by setting the audio output of the DVD player to 2ch PCM. (It may not be possible depending on the player models.)

Even if you set to output audio on the TV speakers, audio will be output from the speakers connected to the AV receiver when you adjust the volume or switch the input on the AV receiver. To output audio from the TV speakers, re- do the corresponding operations on the TV.

In case of an p connection with u and u audio control compatible components, do not connect the u cable at the same time.

On the TV, when you select anything other than the HDMI jack to which the AV receiver is connected, the input on the AV receiver will be switched to TV/CD.

The AV receiver will automatically power on in conjunction when it determines it to be necessary. Even if the AV receiver is connected to an p compatible TV or player/recorder, it will not power on if it is not necessary. It may not power on in conjunction when the TV is set to output audio from the TV.

Linked functions with the AV receiver may not work depending on the component model connected. In such cases, operate the AV receiver directly.

Appendix

En-88

About HDMI Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital audio (2- channel PCM, multichannel digital audio, and multichannel PCM). The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface)*1, so TVs and displays with a DVI input can be connected by using an HDMI-to- DVI adapter cable. (This may not work with some TVs and displays, resulting in no picture.) The AV receiver uses HDCP (High-bandwidth Digital Content Protection)*2, so only HDCP-compatible components can display the picture.

2-channel linear PCM (32192 kHz, 16/20/24 bit) Multichannel linear PCM (up to 7.1 ch, 32192 kHz,

16/20/24 bit) Bitstream (DSD, Dolby Digital, Dolby Digital Plus,

Dolby TrueHD, DTS, DTS-HD High Resolution Audio, DTS-HD Master Audio)

Your Blu-ray Disc/DVD player must also support HDMI output of the above audio formats.

The AV receiver supports HDCP (High-bandwidth Digital Content Protection)*2, a copy-protection system for digital video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.

*1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 in 1999.

*2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. Its designed to protect video content and requires a HDCP-compatible device to display the encrypted video.

*3 DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open industry groups objective is to address the industrys requirements for a digital connectivity specification for high-performance PCs and digital displays.

Note

The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so youll need to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.

The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or theres no sound from a component connected via HDMI, check its setup. Refer to the connected components instruction manual for details.

The AV receivers HDMI interface is based on the following: Audio Return Channel, 3D, x.v.Color, DeepColor, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multichannel PCM.

Supported Audio Formats About Copyright Protection

Appendix

En-89

Network/USB Features

The following diagram shows how you can connect the AV receiver to your home network. In this example, its connected to a LAN port on a router, which has a 4-port 100Base-TX switch built-in.

Ethernet Network For the best results, a 100Base-TX switched Ethernet network is recommended. Although its possible to play music on a computer thats connected to the network wirelessly, playback may be unreliable, so it is recommended to use wired connections.

Ethernet Router A router manages the network, data-routing and supplying of IP addresses. Your router must support the following: NAT (Network Address Translation). NAT allows

several networked computers to access the Internet simultaneously via a single Internet connection. The AV receiver needs Internet access for Internet radio.

DHCP (Dynamic Host Configuration Protocol). DHCP supplies IP addresses to the network devices, allowing them to configure themselves automatically.

A router with a built-in 100Base-TX switch is recommended.

Some routers have a built-in modem, and some Internet Service Providers (ISP) require you to use specific routers. Please consult your ISP or computer dealer if youre unsure.

CAT5 Ethernet cable Use a shielded CAT5 Ethernet cable (straight-type) to connect the AV receiver to your home network.

Internet Access (for Internet radio) To receive Internet radio, your Ethernet network must have Internet access. A narrowband Internet connection (e.g., 56K modem, ISDN) will not provide satisfactory results, so a broadband connection is strongly recommended (e.g., cable modem, xDSL modem, etc). Please consult your ISP or computer dealer if youre unsure.

Note

To receive Internet radio with the AV receiver, your broadband Internet connection must be working and able to access the Web.

Consult your ISP if you have any problems with your Internet connection.

The AV receiver uses DHCP to configure its network settings automatically. If you want to configure these settings manually, see Network ( page 62).

The AV receiver does not support PPPoE settings, so if you have a PPPoE-type Internet connection, you must use a PPPoE- compatible router.

Depending on your ISP, you may need to specify a proxy server to use Internet radio. If your computer is configured to use a proxy server, use the same settings for the AV receiver ( page 62).

Connecting to the Network

WAN

LAN

Modem

Router

Computer or media server

Internet radio

Network Requirements

Appendix

En-90

Server playback The AV receiver can play digital music files stored on a computer or media server and supports the following technologies: Windows Media Player 11 Windows Media Player 12 Windows Media Connect 2.0 DLNA-certified media server If the operating system of your computer is Windows Vista, Windows Media Player 11 is already installed. Windows Media Player 11 for Windows XP can be downloaded for free from the Microsoft web site. The computer or media server must be on the same

network as the AV receiver. Up to 20,000 folders can be displayed, and folders may

be nested up to 16 levels deep.

Note

Depending on the media server, the AV receiver may not recognize it, or may not be able to play its music files.

Remote playback Windows Media Player 12 DLNA-certified (within DLNA Interoperability

Guidelines version 1.5) media server or controller device. The setting varies depending on the media server or controller devices. Refer to your devices instruction manual for details. If the operating system of your personal computer is Windows 7, Windows Media Player 12 is already installed. For more information, see the Microsoft web site.

USB mass storage device class (but not always guaranteed).

FAT16 or FAT32 file system format. If the storage device has been partitioned, each section

will be treated as an independent device. Up to 20,000 folders can be displayed, and folders may

be nested up to 16 levels deep. USB hubs and USB devices with hub functions are not

supported.

Note

If the media you connect is not supported, the message No Storage will be displayed.

If you connect a USB hard disk drive to the AV receivers USB port, we recommend that you use its AC adapter to power it.

The AV receiver supports USB MP3 players that support the USB Mass Storage Class standard, which allows USB devices to be connected to computers without the need for special drivers or software. Note that not all USB MP3 players support the USB Mass Storage Class standard. Refer to your USB MP3 players instruction manual for details.

Protected WMA music files on an MP3 player cannot be played. Onkyo accepts no responsibility whatsoever for the loss or

damage to data stored on a USB device when that device is used with the AV receiver. We recommend that you back up your important music files beforehand.

MP3 players containing music files that are managed with special music software are not supported.

Operation is not guaranteed for all USB devices, which includes the ability to power them.

Do not connect your USB device via a USB hub. The USB device must be connected directly to the AV receivers USB port.

If the USB device contains a lot of data, the AV receiver make take a while to read it.

USB devices with security functions cannot be played.

Server Requirements Minimum system requirements for Windows Media Player 11 on Windows XP Operating system Windows XP Home Edition (SP2), Windows XP Professional (SP2), Windows XP Tablet PC Edition (SP2), Update Rollup 2 for Windows XP Media Center Edition 2005 (KB900325), October 2006 Update Rollup for Windows XP Media Center Edition (KB925766)

Processor: 233 MHz Intel Pentium II, Advanced Micro Devices (AMD), etc.

Memory: 64 MB

Hard disk: 200 MB of free space

Drive: CD or DVD drive

Modem: 28.8 kbps

Sound card: 16-bit sound card

Monitor: Super VGA (800 x 600)

Video card: 64 MB VRAM, DirectX 9.0b

Software: Microsoft ActiveSync (only when using a Windows Mobile-based Pocket PC or smartphone)

Web browser: Microsoft Internet Explorer 6 or Netscape 7.1

USB Device Requirements

Appendix

En-91

For server playback and playback from a USB device, the AV receiver supports the following music file formats. Variable bit-rate (VBR) files are supported. However, playback times may not display correctly.

Note

With remote playback, the AV receiver does not support the following music file formats: FLAC and Ogg Vorbis.

In the case of server playback, the above-mentioned file formats may not be played depending on the server type.

MP3 (.mp3 or .MP3) MP3 files must be MPEG-1/MPEG-2 Audio Layer 3

format with sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and bitrates of between 8 kbps and 320 kbps. Incompatible files cannot be played.

WMA (.wma or .WMA) WMA stands for Windows Media Audio and is an audio compression technology developed by Microsoft Corporation. Audio can be encoded in WMA format by using Windows Media Player. WMA files must have the copyright option turned off. Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, bitrates of between 5 kbps and 320 kbps, and WMA DRM are supported.

WMA Pro/Voice formats are not supported.

WMA Lossless (.wma or .WMA) Sampling rates of 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz

are supported. Quantization bit: 16 bit, 24 bit

WAV (.wav or .WAV) WAV files contain uncompressed PCM digital audio. Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz are supported.

Quantization bit: 8 bit, 16 bit, 24 bit

AAC (.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/ .3GP or .3G2)

AAC stands for MPEG-2/MPEG-4 Audio. Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz and bitrates of between 8 kbps and 320 kbps are supported.

FLAC (.flac or .FLAC) FLAC is a file format for lossless audio data compression. Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz are supported.

Quantization bit: 8 bit, 16 bit, 24 bit

Ogg Vorbis (.ogg or .OGG) Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and bitrates of between 48 kbps and 500 kbps are supported. Incompatible files cannot be played.

LPCM (Linear PCM) Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz are supported.

Quantization bit: 8 bit, 16 bit, 24 bit * Only for playback via network.

The Digital Living Network Alliance is an international, cross-industry collaboration. Members of DLNA develop a concept of wired and wireless interoperable networks where digital content such as photos, music, and videos can be shared through consumer electronics, personal computers, and mobile devices in and beyond the home. The AV receiver complies with the DLNA Interoperability Guidelines version 1.5.

Supported Audio File Formats About DLNA

Appendix

En-92

License and Trademark Information x.v.Color is a trademark of Sony Corporation.

Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered trademarks & DTS-HD Master Audio is a trademark of DTS, Inc. Product includes software. DTS, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.

Music Optimizer is a trademark of Onkyo Corporation.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

InstaPrevue and the InstaPrevue logo are trademarks or registered trademarks of Silicon Image, Inc. in the United States and other countries.

iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Made for iPod and Made for iPhone mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

Apple TV is a trademark of Apple Inc., registered in the U.S. and other countries.

Manufactured under license from Audyssey Laboratories, Inc. U.S. and foreign patents pending. Audyssey 2EQ, Audyssey Dynamic EQ and Audyssey Dynamic Volume are registered trademarks of Audyssey Laboratories, Inc.

DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital Living Network Alliance.

Windows and the Windows logo are trademarks of the Microsoft group of companies.

Qdeo and QuietVideo are trademarks of Marvell or its affiliates.

MHL, the MHL Logo, and Mobile High-Definition Link are trademark or registered trademarks of MHL LLC in the United States and other counties.

Appendix

En-93

Specifications Amplifier Section

Video Section

Tuner Section

General

HDMI

Video Inputs

Video Outputs

Audio Inputs

Audio Outputs

Others

Specifications and features are subject to change without notice.

Rated Output Power All channels: 80 watts minimum continuous power per

channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.7% (FTC)

Dynamic Power* * IEC60268-Short-term maximum output power

180 W (3 , Front) 160 W (4 , Front) 100 W (8 , Front)

THD+N (Total Harmonic Distortion+Noise) 0.08% (20 Hz - 20 kHz, half power)

Damping Factor 60 (Front, 1 kHz, 8 )

Input Sensitivity and Impedance (Unbalance) 200 mV/47 k (LINE)

Rated RCA Output Level and Impedance 200 mV/2.2 k (LINE OUT)

Maximum RCA Output Level and Impedance 2 V/2.2 k (LINE OUT)

Frequency Response 5 Hz - 100 kHz/+1 dB, 3 dB (DSP bypass)

Tone Control Characteristics 10 dB, 50 Hz (BASS) 10 dB, 20 kHz (TREBLE)

Signal to Noise Ratio 100 dB (LINE, IHF-A)

Speaker Impedance 6 - 16

Input Sensitivity/Output Level and Impedance 1 Vp-p/75 (Component Y) 0.7 Vp-p/75 (Component PB/CB, PR/CR) 1 Vp-p/75 (Composite)

Component Video Frequency Response 5 Hz - 100 MHz/+0 dB, 3 dB

FM Tuning Frequency Range 87.5 MHz - 107.9 MHz

AM Tuning Frequency Range 530 kHz - 1710 kHz

Preset Channel 40

Power Supply AC 120 V, 60 Hz

Power Consumption 5 A

No-sound Power Consumption 65 W

Stand-by Power Consumption 0.15 W

Dimensions (W H D) 435 mm 173.5 mm 328 mm 17-1/8" 6-13/16" 12-15/16"

Weight 9.0 kg (19.8 lbs.)

Input IN 1, IN 2, IN 3, IN 4, IN 5, IN 6, IN 7, AUX INPUT

Output OUT MAIN, OUT SUB

Video Resolution 1080p

Audio Format Dolby TrueHD, DTS-HD Master Audio, DVD-Audio, DSD

Supported 3D, Audio Return Channel, DeepColor, x.v.Color, LipSync, CEC (RIHD)

Component IN 1

Composite BD/DVD, CBL/SAT, GAME, PC, USB

Component OUT

Composite MONITOR OUT

Digital Optical: 2 Coaxial: 2

Analog BD/DVD, CBL/SAT, GAME, PC, TV/CD

Analog ZONE2 LINE OUT

Subwoofer Pre Outputs 2

Speaker Outputs Main (L, R, C, SL, SR, SBL/FHL, SBR/FHR) + ZONE2 (L, R)

Phones 1 (6.3 )

Setup Mic 1

RI 1

USB 1 (Front)/1 (Rear)

Ethernet 1

Appendix

En-94

Memo

Appendix

En-95

Memo

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 http://www.onkyo.com/

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.eu.onkyo.com/

The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700

Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.onkyochina.com/

1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 http://www.cn.onkyo.com/

SN 29401115EN (C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved.

* 2 9 4 0 1 1 1 5 E N *

Y1203-1

Using Internet Radio

En-1

Using Internet Radio

Note

Available services may vary depending on the region.

Common Procedures in Internet Radio Menu

1 Press NET. A list of the network services appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver.

2 Select the desired service and press ENTER. The top page of the selected service appears.

Using Multiple Accounts The AV receiver supports multiple user accounts, which means you can freely switch between several logins. After registering user accounts, login is performed from the Users screen.

Tip

Some of the services dont allow the use of multiple user accounts.

You can store up to 10 user accounts. To switch between accounts you must first log out from the

current account, and log in again on the Users screen.

1 Press MENU while the Users screen is displayed. The following menu items appear: Add new user: Remove this user: You can either store a new user account, or delete an existing one.

Pandora internet radio Getting Started (U.S. only) ................................................. 2

Using Rhapsody (U.S. only).......................... 3

Using the SiriusXM Internet Radio (North American only) ......................................... 4

Using Last.fm Internet Radio ........................ 5

Using Slacker Personal Radio ...................... 6

Using MP3tunes ............................................. 7

Using Internet Radio

En-2

Pandora is a free, personalized Internet radio service that plays the music you know and helps you discover music youll love.

PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc. Used with permission.

Pandora internet radio Getting Started (U.S. only)

1 Use q/w to select I have a Pandora Account or Im new to Pandora and then press ENTER. If you are new to Pandora select Im new to Pandora. You will see an activation code on your TV screen. Please write down this code. Go to an Internet connected computer and point your browser to www.pandora.com/onkyo Enter your activation code and then follow the instructions to create your Pandora account and your personalized Pandora Internet radio stations. You can create your stations by entering your favorite songs and artists when prompted. After you have created your account and stations you can return to your Onkyo receiver and press enter to begin listening to your personalized Pandora Internet radio. If you have an existing Pandora account, you can add your Pandora account to your Onkyo receiver by selecting I have a Pandora Account and logging in with your email and password.

Tip

If you want to use multiple user accounts, see Using Multiple Accounts ( page 1). Login can be made from the Users screen.

2 To play a station, use q/w to select the station from your station list, and then press ENTER. Playback starts and the playback screen appears. Create a New Station: Enter the name of a song, artist, or genre and Pandora will create a unique radio station for you based on the musical qualities of that song, artist, or genre.

Menu Items I like this song: Give a song thumbs-up and Pandora will play more music like it. I dont like this song: Give a song thumbs-down and Pandora will ban that song from the current station. Why is this song playing?: Discover some of the musical attributes that Pandora uses to create your personal radio stations. Dont play the song for a month: If you are tired of a song, you can put the song to sleep and Pandora will not play it for one month. Create station from this artist: Creates a radio station from this artist.

Delete this station: This will permanently delete a station from your Pandora account. All of your thumbs feedback will be lost should you choose to re-create the station with the same song or artist. Create station from this song: Creates a radio station from this song. Rename this station: Lets you rename the current radio station. Bookmark this artist: Pandora will bookmark your favorite artist for your profile on www.pandora.com. Bookmark this song: Pandora will bookmark the current song and allow you to buy them all from Amazon or iTunes in one step! Add to My Favorites: Adds a station to My Favorites list.

Using Internet Radio

En-3

Using Rhapsody (U.S. only)

1 Use q/w to select Sign in to your account and then press ENTER. To use Rhapsody, you need an account. If you dont have one yet, you can create a new account at www.rhapsody.com/onkyo If you have an existing Rhapsody account, select Sign in to your account and press ENTER. Enter your user name (usually your email) and password in the next keyboard screen, or in Web Setup.

Using the keyboard screen 1. Use q/w/e/r and ENTER to enter your user

name and password. 2. Select OK. 3. Press ENTER. The Confirm your entries

screen appears. 4. Press ENTER.

Tip

If you want to use multiple user accounts, see Using Multiple Accounts ( page 1). Login can be made from the Users screen.

2 Use q/w to select the menu, then press ENTER. Search: You can search for music by Artist, Album, or Track. Music Guide: You can play tracks from Genres, Top Artists, Top Albums, Top Tracks, New Releases, and Staff Picks. Rhapsody Channels: Listen to radio channels programmed by Rhapsodys top-notch editors. Playlists: Play your own personal playlists. My Library: Bookmark your favorite albums and tracks from the Rhapsody catalog using My Library. Account Info: Confirm your account information. Sign Out: Sign out from your Rhapsody account.

3 Use q/w to select a channel, and press ENTER or 1 to start playback. Playback starts and the playback screen appears. You can control the tracks with the buttons on the remote control.

Enabled buttons: 1, 3, 2, 5, 4, 7, 6, RANDOM, REPEAT

Note

On Rhapsody Channels, some of the buttons dont work.

Menu Items Add track to My Library: Bookmark currently-playing tracks. Add album to My Library: Bookmark currently-playing albums. Add playlist to My Library: Bookmark currently-playing playlists. Add channel to My Channels: Bookmark currently-playing Rhapsody radio channels. Add to My Favorites: Adds a track, channel or playlist to My Favorites list.

Tip

You can remove bookmarked tracks, albums, and Rhapsody Channels from My Library.

Using Internet Radio

En-4

Your Onkyo AV receiver includes a free trial of SiriusXM Internet Radio. The Account Info screen shows how many days are left in your trial. After the trial period expires, if you want to continue listening to the service, you must subscribe. To subscribe go to www.siriusxm.com/internetradio with your computer.

When you subscribe, you will be provided with a username and password which has to be entered into the AV receiver.

To use SiriusXM Internet Radio, you must have your AV receiver connected to the Internet. Using the remote control, follow these steps:

SiriusXM Internet Radio subscriptions are sold separately and are governed by the Sirius Terms and Conditions (see www.sirius.com). Be sure to read this agreement before you purchase your subscription. Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. All rights reserved.

Using the SiriusXM Internet Radio (North American only)

1 Use q/w to select Sign In, and then press ENTER. If you have an existing SIRIUS account, you can sign in by selecting Sign In. Enter your user name and password in the next keyboard screen, or in Web Setup. If you dont know your username or password, call Sirius XM at (888) 539-7474 for assistance.

Tip

If you want to use multiple user accounts, see Using Multiple Accounts ( page 1). Login can be made from the Users screen.

Using the keyboard screen 1. Use q/w/e/r and ENTER to enter your user

name and password. 2. Select OK. 3. Press ENTER. The Confirm your entries

screen appears. 4. Press ENTER. Please wait... appears and then SiriusXM Internet Radio screen appears which displays the category available for selection.

2 Use q/w to select the category and then press ENTER. The channel list screen for the selected category appears.

3 Use q/w to select the desired channel and then press ENTER. The playback screen for the selected channel appears and you can listen to SiriusXM Internet Radio. You can control the tracks with the buttons on the remote control.

Enabled buttons: 2, 3, 7, 6

Menu Items Add to My Favorites: Adds a channel to My Favorites list.

Using Internet Radio

En-5

Last.fm is a music service that learns what you love... Your new Onkyo AV receiver is very clever. If you have a free Last.fm account, it will keep track of all the songs youve just played. When you visit the Last.fm website, you can see personal charts of the music youve enjoyed, share them with friends and see what they like, too.

With thousands of biographies, reviews and an endless choice of personalised, ad-free radio stations, Last.fm is a great way to discover music. Pick up your free Last.fm account today at www.last.fm/join

Get a subscription and you can enjoy the best of ad-free Last.fm Radio on your Onkyo AV receiver without a computer! Recommended Radio: Discover smart personalised recommendations that adapt as your tastes change. Artist Radio: Pick any artist and well play you a whole station of music inspired by your choice. My Library: Sit back and enjoy selections from all the music youve heard since you joined Last.fm. Tag Radio: Polish funk? Death pop? Think of a style and well entertain you with it for hours.

Start your free trial straight away when you create your account and see for yourself what its like to have the worlds music at your fingertips. Latest prices and full information are available at www.last.fm/subscribe

Using scrobbling control Use q/w to select Enable, and then press ENTER.

* Internet radio services provided by a third party may be terminated with or without notice. Internet radio services may not be available in some areas.

Using Last.fm Internet Radio 1 Use q/w to select Sign in to your account, and then press ENTER. If you have the existing Last.fm account, you can sign in to your account to select Sign in to your account. Enter your user name and password in the next keyboard screen.

Using the keyboard screen 1. Use q/w/e/r and the ENTER to enter your user

name and password. 2. Select OK. 3. Press ENTER. The Confirm your entries

screen appears. 4. Press ENTER. Please wait... appears and then Last.fm Internet Radio screen appears.

Tip

If you want to use multiple user accounts, see Using Multiple Accounts ( page 1). Login can be made from the Users screen.

2 Use q/w to select menu and then press ENTER. Search Station: You can search station by Artist, Tag, or User Name. Top Artists Station: You can play tracks of top-rated artists. Top Tags Station: You can play tracks of top-rated tags. Personal Station: You can play tracks from personalized station

(Your Library, Your Neighbourhood and Your Recommendations).

Profile: You can play tracks from Recently Listened Tracks, Library and Neighbours. Account Info: Confirm your account information. Sign Out: It signs out from your account.

3 Use q/w to select a station, and press ENTER or 1 to start playback. Playback starts and the playback screen appears.

Menu Items I Love this track: Track information is saved in Last.fm server, and playback frequency increases. Ban this track: Track information is saved in Last.fm server, and playback frequency reduces. Add to My Favorites: Adds a station to My Favorites list.

Using Internet Radio

En-6

Using Slacker Personal Radio

1 If you do not have an account, create one on the Slacker website (www.slacker.com) with your computer.

If you already have a Slacker account, select Sign in to your account and then press ENTER. The keyboard screen appears. You can enter information from the remote control or the keys on the main unit.

2 If there are no mistakes in the information you have entered, use q/w/e/r to select OK then press ENTER. An account information confirmation screen appears.

3 If you do not have an account, select Access without Sign In and press ENTER to use a restricted version of the service. Note that use will be restricted.

Tip

If you want to use multiple user accounts, see Using Multiple Accounts ( page 1). Login can be made from the Users screen.

4 Use q/w to select a menu item and then press ENTER.

To sign out, use q/w to select Sign out from this screen and then press ENTER.

5 Use q/w to select a station and then press ENTER or 1 to start playback from the station. The playback screen appears.

6 You can control the tracks with the buttons on the remote control.

Enabled buttons: 1, 3, 2, 6

Menu Items Rate Song as Favorite: Stores information to server, making it more likely that the song will be played again. Ban Song: Stores information to server, making it less likely that the song will be played again. Ban Artist: Stores information to server, making it less likely that the songs from this artist will be played again. Mark Favorite: Adds the currently playing station to your favorites. Unmark Favorite: Deletes the currently playing station from your favorites. Add song to Library: Adds the currently playing track to your library. Delete song from Library: Deletes the currently playing track from your library. Add to My Favorites: Adds a station or song to My Favorites list.

Using Internet Radio

En-7

Listen to your music collection on your home stereo in complete digital fidelity without a personal computer plus safely backup all your songs. Heres how:

Creating an Account on your Computer

Playing Contents on the AV Receiver

Tip

Before proceeding, you need to select the MP3tunes service as described in Common Procedures in Internet Radio Menu ( page 1).

Using MP3tunes

1 From your computer, open a web browser and go to: www.mp3tunes.com/signup

2 Create an account.

3 Click the Upload link (www.mp3tunes.com/upload) to add files to your Locker.

4 View, edit and listen to your files by clicking on Player (www.mp3tunes.com/player).

1 Use q/w to select Sign in to your account, and then press ENTER.

2 Enter the e-mail address and password you used when creating your account, select OK and press ENTER. The keyboard screen appears. You can enter your user name and password from the remote controller or the buttons on the AV receiver.

3 If there are no mistakes in the information you have entered, select OK and press ENTER. An account information confirmation screen appears.

Tip

If you want to use multiple user accounts, see Using Multiple Accounts ( page 1). Login can be made from the Users screen.

4 Use q/w to select the menu, then press ENTER. Music: The place to find your Artists, Albums, and Playlists. Shuffle: Starts playing a random selection of tracks from your Locker. Search: Find a specific Album, Artist, or Song. Account Info: Your MP3tunes account information. Sign Out:

Log out of your MP3tunes account.

The track at the top of the music list is automatically played back.

5 Use q/w to select a track and press ENTER or 1 to start playback. A playback screen appears. You can control the tracks with the buttons on the remote control.

Enabled buttons: 1, 3, 2, 7, 6

Menu Items Go to Menu: Displays additional menu options.

6 You can view or change your MP3tunes account settings by going to www.mp3tunes.com/account.

Utilisation dune webradio

Fr-1

Utilisation dune webradio

Remarque

Les services disponibles peuvent varier en fonction de la rgion.

Procdures courantes dans le menu de webradio

1 Appuyez sur NET. Une liste des services rseau saffiche, et le tmoin NET sallume. Sil clignote, vrifiez que le cble Ethernet est fermement branch sur lampli-tuner AV.

2 Slectionnez le service dsir et appuyez sur ENTER. La page principale du service slectionn saffiche.

Utilisation de plusieurs comptes Lampli-tuner AV prend en charge plusieurs comptes utilisateur, ce qui signifie que vous pouvez librement commuter entre plusieurs connexions. Aprs avoir enregistr des comptes utilisateur, lidentification est ralise partir de lcran Users .

Conseil

Certains des services ne permettent pas lutilisation de plusieurs comptes utilisateur.

Vous pouvez stocker jusqu 10 comptes utilisateur. Pour commuter entre les comptes, vous devez dabord vous

dconnecter du compte actuel, puis vous reconnectez depuis lcran Users .

1 Appuyez sur MENU lorsque lcran Users est affich. Les lments de menu suivants saffichent : Add new user : Remove this user : Vous pouvez soit stocker un nouveau compte utilisateur, soit en supprimer un existant.

Pandora internet Radio Pour commencer (tats-Unis uniquement).......................... 2

Utilisation de Rhapsody (Etats-Unis uniquement).............................................. 3

Utilisation de SiriusXM Internet Radio (Amrique du Nord uniquement) ............ 4

Utilisation de la webradio Last.fm................ 5

Utilisation de Slacker Personal Radio ......... 6

Utilisation dune webradio

Fr-2

Pandora est un service de radio en ligne libre et personnalis vous permettant de lire la musique que vous connaissez et de dcouvrir celle que vous aimez.

PANDORA, le logo PANDORA, et lhabillage commercial Pandora sont des marques commerciales ou des marques dposes de la socit Pandora Media, Inc. Utilises avec autorisation.

Pandora internet Radio Pour commencer (tats-Unis uniquement)

1 Utilisez q/w pour slectionner I have a Pandora Account ou Im new to Pandora , puis appuyez sur ENTER. Si vous ne connaissez pas Pandora slectionnez Im new to Pandora . Un code dactivation apparatra sur lcran de votre tlviseur. Notez ce code. Utilisez un ordinateur branch sur Internet et connectez le navigateur www.pandora.com/onkyo Saisissez votre code dactivation puis suivez les instructions pour crer votre compte Pandora et vos stations webradio Pandora personnalises. Lorsque vous y tes invits, vous pouvez crer vos stations en saisissant vos chansons et vos artistes prfrs. Aprs la cration de votre compte et de vos stations, vous pouvez retourner votre rcepteur Onkyo et appuyez sur entre pour couter votre webradio Pandora personnalise. Si vous disposez dun compte Pandora, vous pouvez ajouter votre compte Pandora votre rcepteur Onkyo en slectionnant I have a Pandora Account et y accder en entrant votre adresse e-mail et votre mot de passe.

Conseil

Si vous souhaitez utiliser plusieurs comptes utilisateur, consultez Utilisation de plusieurs comptes ( page 1). Lidentification peut tre ralise partir de lcran Users .

2 Pour lire une station, utilisez q/w pour slectionner la station dans votre liste de stations, puis appuyez sur ENTER. La lecture dbute et lcran de lecture saffiche. Create a New Station : Saisissez le nom dune chanson, dun artiste ou dun genre et Pandora crera une station radio unique pour vous en fonction des qualits musicales de la chanson, de lartiste ou du genre choisi.

Elments du menu I like this song : Acceptez la chanson et Pandora lira dautres musiques similaires. I dont like this song : Rejetez la chanson et Pandora liminera cette chanson de la station courante. Why is this song playing? : Dcouvrez certains des attributs musicaux que Pandora utilise pour crer vos stations radio personnelles. Dont play the song for a month : Si vous en avez assez dune chanson, vous pouvez mettre la chanson au repos et Pandora ne la lira plus pendant un mois. Create station from this artist : Permet de crer une station radio partir de cet artiste.

Delete this station : Ceci supprimera de faon permanente la station de votre compte Pandora. Au cas o vous dcideriez de rcrer la station avec les mmes chansons ou les mmes artistes, tous vos acceptations/rejets prcdents seront perdus. Create station from this song : Permet de crer une station radio partir de cette chanson. Rename this station : Vous permet de renommer la station radio actuelle. Bookmark this artist : Pandora marquera votre artiste prfr pour votre profil sur www.pandora.com. Bookmark this song : Pandora marquera la chanson en cours et vous permettra de toutes les acheter sur Amazon ou iTunes en une tape ! Add to My Favorites : Permet dajouter une station la liste My Favorites.

Utilisation dune webradio

Fr-3

Utilisation de Rhapsody (Etats-Unis uniquement)

1 Utilisez q/w pour slectionner Sign in to your account , puis appuyez sur ENTER. Vous devez possder un compte pour utiliser Rhapsody. Si vous ne disposez pas encore dun compte, vous pouvez en crer un partir de www.rhapsody.com/onkyo Si vous possdez dj un compte Rhapsody, slectionnez Sign in to your account , puis appuyez sur ENTER. Saisissez votre nom utilisateur (en gnral votre adresse lectronique) et votre mot de passe dans lcran clavier suivant ou dans Configuration Web.

Utilisation de lcran clavier 1. Utilisez q/w/e/r et ENTER pour saisir votre

nom dutilisateur et votre mot de passe. 2. Slectionnez OK . 3. Appuyez sur ENTER. Lcran Confirm your

entries saffiche. 4. Appuyez sur ENTER.

Conseil

Si vous souhaitez utiliser plusieurs comptes utilisateur, consultez Utilisation de plusieurs comptes ( page 1). Lidentification peut tre ralise partir de lcran Users .

2 Utilisez q/w pour slectionner le menu, puis appuyez sur ENTER. Search : Vous pouvez rechercher des morceaux par artiste, par album ou par piste. Music Guide : Vous pouvez lire des pistes partir des genres,des meilleurs artistes, des meilleurs albums, des meilleures pistes, des nouveauts et des slections du personnel. Rhapsody Channels : coutez les canaux de radio programme par les meilleurs diteurs de Rhapsody. Playlists : Permet de jouer vos listes de lecture personnelles. My Library : Marquez vos albums et vos pistes personnelles dans le catalogue de Rhapsody laide de My Library. Account Info : Vrifiez les informations de votre compte. Sign Out : Dconnectez-vous de votre compte Rhapsody.

3 Utilisez q/w pour slectionner un canal, puis appuyez sur ENTER ou 1 pour dmarrer la lecture. La lecture dbute et lcran de lecture saffiche. Vous pouvez contrlez les pistes avec les touches sur la tlcommande.

Boutons activs : 1, 3, 2, 5, 4, 7, 6, RANDOM, REPEAT

Remarque

Sur les canaux Rhapsody, certaines touches ne fonctionnent pas.

Elments du menu Add track to My Library : Marquez les pistes en cours de lecture. Add album to My Library : Marquez les albums en cours de lecture. Add playlist to My Library : Marquez les listes de lecture en cours de lecture. Add channel to My Channels : Marquez les canaux de radio Rhapsody en cours de lecture. Add to My Favorites : Permet dajouter une piste, un canal ou une liste de lecture la liste My Favorites.

Conseil

Vous pouvez supprimer des pistes, des albums et des canaux Rhapsody marqus de My Library.

Utilisation dune webradio

Fr-4

Votre ampli-tuner AV Onkyo comprend un essai gratuit de SiriusXM Internet Radio. Lcran Account Info affiche le nombre de jours restants dans votre essai. Une fois la priode dessai expire, si vous souhaitez continuer couter le service, vous devez vous abonner. Pour vous inscrire, accdez ladresse www.siriusxm.com/internetradio laide de votre ordinateur.

Lorsque vous vous inscrivez, vous devez fournir un nom est un mot de passe utilisateur qui doivent tre saisis dans lampli-tuner AV.

Pour utiliser SiriusXM Internet Radio, lampli-tuner AV doit tre connect Internet. Suivez les tapes ci-dessous laide de la tlcommande :

Les abonnements SiriusXM Internet Radio sont vendus sparment et sont subordonns par les conditions Sirius (voir www.sirius.com). Assurez-vous de lire cet accord avant dacqurir votre abonnement. Sirius, XM et tous les logos et marques affrents sont des marques dposes de Sirius XM Radio Inc. et de ses filiales. Tous droits rservs.

Utilisation de SiriusXM Internet Radio (Amrique du Nord uniquement)

1 Utilisez q/w pour slectionner Sign In , puis appuyez sur ENTER. Si vous possdez dj un compte SIRIUS, vous pouvez y accder en slectionnant Sign In . Saisissez votre nom utilisateur et votre mot de passe dans lcran clavier suivant ou dans Configuration Web. Si vous ne connaissez pas votre nom dutilisateur ou votre mot de passe, appelez Sirius XM au (888) 539-7474 pour obtenir une assistance.

Conseil

Si vous souhaitez utiliser plusieurs comptes utilisateur, consultez Utilisation de plusieurs comptes ( page 1). Lidentification peut tre ralise partir de lcran Users .

Utilisation de lcran clavier 1. Utilisez q/w/e/r et ENTER pour saisir votre

nom dutilisateur et votre mot de passe. 2. Slectionnez OK . 3. Appuyez sur ENTER. Lcran Confirm your

entries saffiche. 4. Appuyez sur ENTER. Please wait... saffiche, puis lcran SiriusXM Internet Radio affiche la catgorie que vous pouvez slectionner.

2 Utilisez q/w pour slectionner la catgorie, puis appuyez sur ENTER. Lcran de la liste des canaux de la catgorie slectionne saffiche.

3 Utilisez q/w pour slectionner le canal de votre choix, puis appuyez sur ENTER. Lcran de lecture du canal slectionn saffiche et vous pouvez couter SiriusXM Internet Radio. Vous pouvez contrlez les pistes avec les touches sur la tlcommande.

Boutons activs : 2, 3, 7, 6 Elments du menu Add to My Favorites : Permet dajouter un canal la liste My Favorites.

Utilisation dune webradio

Fr-5

Last.fm un service de musique qui apprend ce que vous aimez Votre nouvel ampli-tuner AV Onkyo est trs intelligent. Si vous avez un compte Last.fm gratuit, il garde une trace de toutes les chansons que vous avez juste joues. Quand vous vous rendez sur le site Web de Last.fm, vous pouvez voir les graphiques personnels de la musique que vous avez apprcie, les partagez avec vos amis et galement voir ce quils aiment.

Avec des milliers de biographies, de revues et un choix infini de stations de radio personnalises et sans pub, Last.fm est excellent moyen de dcouvrir de la musique. Crez aujourdhui votre compte Last.fm gratuit sur www.last.fm/join

Inscrivez-vous et vous pourrez apprcier le meilleur de la radio sans pub Last.fm sur votre ampli-tuner AV Onkyo sans ordinateur ! Recommended Radio : Dcouvrez les recommandations personnalises futes qui changent en mme temps que vos gots. Artist Radio : Slectionnez nimporte quel artiste et nous vous jouerons une station entire de musique inspire par votre choix. My Library : Reposez-vous de retour et apprciez les slections partir de toute la musique que vous avez entendue depuis que vous avez joint Last.fm. Tag Radio : Funk polonaise ? Death pop ? Pensez un style et nous vous divertirons avec pendant des heures.

Commencez votre essai gratuit immdiatement la cration votre compte et dcouvrez par vous-mme ce que cela fait davoir la musique du monde au bouts des doigts. Les derniers prix et les informations compltes sont disponibles sur www.last.fm/subscribe

Utilisation du contrle Scrobbling Utilisez q/w pour slectionner Enable , puis appuyez sur ENTER.

* Les services de webradio fournis par un tiers peuvent tre rsilis avec ou sans pravis. Les services de webradio peuvent ne pas tre accessibles dans certaines zones.

Utilisation de la webradio Last.fm 1 Utilisez q/w pour slectionner Sign in to your account , puis appuyez sur ENTER. Vous possdez dj un compte Last.fm, vous pouvez vous y connecter pour slectionner Sign in to your account . Saisissez votre nom utilisateur et votre mot de passe dans lcran clavier suivant.

Utilisation de lcran clavier 1. Utilisez q/w/e/r et le bouton ENTER pour

saisir votre nom dutilisateur et votre mot de passe.

2. Slectionnez OK . 3. Appuyez sur ENTER. Lcran Confirm your

entries saffiche. 4. Appuyez sur ENTER. Please wait... apparait puis lcran Last.fm Internet Radio apparait.

Conseil

Si vous souhaitez utiliser plusieurs comptes utilisateur, consultez Utilisation de plusieurs comptes ( page 1). Lidentification peut tre ralise partir de lcran Users .

2 Utilisez q/w pour slectionner un menu puis appuyez sur ENTER. Search Station : Vous pouvez rechercher une station par artiste, par tag ou par nom dutilisateur. Top Artists Station : Vous pouvez lire des pistes des artistes les mieux valus. Top Tags Station : Vous pouvez lire des pistes des tags les mieux valus. Personal Station : Vous pouvez lire des pistes de votre station personnalise ( Your Library , Your Neighbourhood et Your Recommendations ).

Profile : Vous pouvez lire des pistes de Recently Listened Tracks , Library et Neighbours . Account Info : Vrifiez les informations de votre compte. Sign Out : Pour vous dconnecter de votre compte.

3 Utilisez q/w pour slectionner une station, puis appuyez sur ENTER ou 1 pour dmarrer la lecture. La lecture dbute et lcran de lecture saffiche.

Elments du menu I Love this track : Linformation de la piste est sauvegarde dans le serveur Last.fm, et la frquence de lecture augmente. Ban this track : Linformation de la piste est sauvegarde dans le serveur Last.fm, et la frquence de lecture diminue. Add to My Favorites : Permet dajouter une station la liste My Favorites.

Utilisation dune webradio

Fr-6

Utilisation de Slacker Personal Radio

1 Si vous ne possdez pas de compte, crez-en un partir du site Web de Slacker (www.slacker.com) laide de votre ordinateur.

Si vous possdez dj un compte Slacker, slectionnez Sign in to your account , puis appuyez sur ENTER. Lcran clavier saffiche. Pouvez saisir des informations partir de la tlcommande ou des touches sur lappareil principal.

2 Si les informations que vous avez saisies ne comportent pas derreur, utilisezq/w/e/r pour slectionner OK , puis appuyez sur ENTER. Lcran de confirmation des informations du compte saffiche.

3 Si vous ne possdez pas de compte, slectionnez Access without Sign In , puis appuyez sur ENTER pour utiliser une version restreinte du service. Veuillez noter que lutilisation est restreinte.

Conseil

Si vous souhaitez utiliser plusieurs comptes utilisateur, consultez Utilisation de plusieurs comptes ( page 1). Lidentification peut tre ralise partir de lcran Users .

4 Utilisez q/w pour slectionner un lment du menu, puis appuyez sur ENTER. Pour vous dconnecter, utilisez q/w pour slectionner Sign out depuis cet cran, puis appuyez sur ENTER.

5 Utilisez q/w pour slectionner une station, puis appuyez sur ENTER ou 1 pour dmarrer la lecture depuis cette station. Lcran de lecture apparat.

6 Vous pouvez contrlez les pistes avec les touches sur la tlcommande. Boutons activs : 1, 3, 2, 6 Elments du menu Rate Song as Favorite : Permet de stocker des informations sur le serveur, et daugmenter la probabilit que le morceau soit lu de nouveau. Ban Song : Permet de stocker des informations sur le serveur, et de diminuer la probabilit que le morceau soit lu de nouveau. Ban Artist : Permet de stocker des informations sur le serveur, et de diminuer la probabilit que les morceaux de cet artiste soient lus de nouveau. Mark Favorite : Permet dajouter la station en cours de lecture vos favoris. Unmark Favorite : Permet de supprimer la station en cours de lecture de vos favoris. Add song to Library : Permet dajouter la piste en cours de lecture votre bibliothque. Delete song from Library : Permet de supprimer la piste en cours de lecture de votre bibliothque. Add to My Favorites : Permet dajouter une station ou un morceau la liste My Favorites.

Uso de Internet Radio

Es-1

Uso de Internet Radio

Nota

Los servicios disponibles pueden variar de una regin a otra.

Procedimientos comunes en el men Internet Radio

1 Pulse NET. Aparecer una lista de los servicios de red y se iluminar el indicador NET. Si parpadea, verifique que el cable Ethernet est firmemente conectado al receptor de AV.

2 Seleccione el servicio deseado y pulse ENTER. Aparecer la pgina principal del servicio seleccionado.

Uso de mltiples cuentas El receptor de AV permite mltiples cuentas de usuario, lo que quiere decir que se puede cambiar libremente entre varios usuarios. Despus de registrar las cuentas de usuario, el acceso se realiza desde la pantalla Users.

Consejo

Algunos de los servicios no permiten el uso de mltiples cuentas de usuario.

Puede guardar hasta 10 cuentas de usuario. Para cambiar entre cuentas debe antes cerrar sesin en la

cuenta actual y acceder de nuevo en la pantalla Users.

1 Pulse MENU cuando aparezca la pantalla de usuarios. Aparecern los siguientes elementos del men: Add new user: Remove this user: Puede guardar una nueva cuenta de usuario o borrar una existente.

Pandora Internet Radio Primeros pasos (solo EE.UU.) ............................................ 2

Uso de Rhapsody (slo EE.UU.)................... 3

Uso de SiriusXM Internet Radio (solo Norteamrica) ........................................... 4

Uso de Last.fm Internet Radio ...................... 5

Uso de Slacker Personal Radio .................... 6

Uso de Internet Radio

Es-2

Pandora es un servicio de radio por Internet gratuito y personalizado que reproduce la msica que usted conoce y le ayudar a descubrir msica que le encantar.

PANDORA, el logotipo de PANDORA logo, y la imagen corporativa de Pandora son marcas comerciales o marcas comerciales registradas de Pandora Media, Inc. Uso con permiso.

Pandora Internet Radio Primeros pasos (solo EE.UU.)

1 Utilice q/w para seleccionar I have a Pandora Account o Im new to Pandora y luego pulse ENTER. Si no conoce Pandora seleccione Im new to Pandora. Ver un cdigo de activacin en la pantalla del televisor. Tome nota de este cdigo. Vaya a un ordenador conectado a Internet y dirija el navegador a www.pandora.com/onkyo Introduzca su cdigo de activacin y siga las instrucciones para crear su cuenta de Pandora y sus emisoras de radio por Internet personalizadas de Pandora. Puede crear sus propias emisoras introduciendo sus canciones y artistas favoritos cuando aparezca la solicitud correspondiente. Una vez creada su cuenta y sus emisoras, puede regresar al receptor Onkyo y pulsar Enter para empezar a escuchar su radio por Internet personalizada de Pandora. Si ya dispone de una cuenta de Pandora, puede aadirla al receptor Onkyo seleccionando I have a Pandora Account e iniciando la sesin con su direccin de correo electrnico y contrasea.

Consejo

Si desea utilizar mltiples cuentas de usuario, consulte Uso de mltiples cuentas ( pgina 1). Se puede iniciar sesin desde la pantalla Users.

2 Utilice q/w para seleccionar la emisora en la lista de emisoras y luego pulse ENTER. Se inicia la reproduccin y aparece la pantalla de reproduccin. Create a New Station: Introduzca el nombre de una cancin, artista o gnero; Pandora crear una emisora de radio exclusiva para usted basada en las cualidades musicales de esa cancin, de ese artista o de ese gnero.

Elementos del men I like this song: Si aprueba (pulgar arriba) una cancin, Pandora reproducir ms msica parecida. I dont like this song: Si no aprueba (pulgar abajo) la cancin, Pandora eliminar dicha cancin de la emisora actual. Why is this song playing?: Descubra algunos de los atributos musicales que Pandora utiliza para crear sus emisoras de radio personalizadas. Dont play the song for a month: Si se cansa de una cancin, puede silenciarla de modo que Pandora no la reproduzca durante un mes. Create station from this artist: Crea una emisora de radio a partir de este artista.

Delete this station: Esto eliminar de forma permanente una emisora de su cuenta de Pandora. Toda la informacin sobre sus aprobaciones / desaprobaciones se perder si quiere volver a crear la emisora con la misma cancin o artista. Create station from this song: Crea una emisora de radio a partir de esta cancin. Rename this station: Le permite renombrar la emisora de radio actual. Bookmark this artist: Pandora marcar su artista favorito para su perfil en www.pandora.com. Bookmark this song: Pandora marcar la cancin actual y le permitir comprarlas todas en Amazon o iTunes con un solo paso. Add to My Favorites: Aade una emisora a la lista Mis favoritos.

Uso de Internet Radio

Es-3

Uso de Rhapsody (slo EE.UU.)

1 Utilice q/w para seleccionar Sign in to your account y luego pulse ENTER. Para utilizar Rhapsody, necesitar una cuenta. Si todava no tiene una, puede crear una nueva en www.rhapsody.com/onkyo Si ya tiene una cuenta Rhapsody, seleccione Sign in to your account y pulse ENTER. Escriba su nombre de usuario (normalmente el correo electrnico) y contrasea en la pantalla de teclado que aparece a continuacin o en la configuracin web.

Utilizacin de la pantalla de teclado 1. Utilice q/w/e/r y ENTER para introducir su

nombre de usuario y su contrasea. 2. Seleccione OK. 3. Pulse ENTER. Aparecer la pantalla Confirm

your entries. 4. Pulse ENTER.

Consejo

Si desea utilizar mltiples cuentas de usuario, consulte Uso de mltiples cuentas ( pgina 1). Se puede iniciar sesin desde la pantalla Users.

2 Utilice q/w para seleccionar el men y luego pulse ENTER. Search: Puede buscar msica por artista, lbum o cancin. Music Guide: Puede reproducir canciones por gneros, artistas principales, lbumes principales o canciones principales, novedades, seleccin del sitio. Rhapsody Channels: Escuche las emisoras de radio programadas por los principales redactores de Rhapsody. Playlists: Reproduzca sus listas personales. My Library: Marque sus lbumes y canciones preferidas en el catlogo de Rhapsody, usando Mi biblioteca. Account Info: Confirme los datos de su cuenta. Sign Out: Salga de su cuenta Rhapsody.

3 Utilice q/w para seleccionar una emisora y luego pulse ENTER o 1 para iniciar la reproduccin. Se inicia la reproduccin y aparece la pantalla de reproduccin. Puede controlar las pistas con los botones del mando a distancia.

Botones activados: 1, 3, 2, 5, 4, 7, 6, RANDOM, REPEAT

Nota

En Rhapsody Channels, algunos de los botones no funcionan.

Elementos del men Add track to My Library: Marca las canciones que se estn reproduciendo actualmente. Add album to My Library: Marca los lbumes que se estn reproduciendo actualmente. Add playlist to My Library: Marca las listas de reproduccin que se estn reproduciendo actualmente. Add channel to My Channels: Marca las emisoras de Rhapsody que se estn reproduciendo actualmente. Add to My Favorites: Aade una cancin, emisora o lista de reproduccin a la lista Mis favoritos.

Consejo

Puede eliminar las canciones, los lbumes y las emisoras de Rhapsody marcados de Mi biblioteca.

Uso de Internet Radio

Es-4

Su receptor de AV Onkyo incluye una prueba gratuita de SiriusXM Internet Radio. La pantalla Account Info muestra los das que quedan de la prueba. Una vez que termine el periodo de prueba, si desea seguir escuchando este servicio, deber contratarlo. para suscribirse vaya a www.siriusxm.com/internetradio con su ordenador.

Cuando se suscriba, recibir un nombre de usuario y una contrasea que deber introducir en el receptor de AV.

Para poder utilizar SiriusXM Internet Radio, el receptor de AV debe estar conectado a internet. Para usar el mando a distancia, siga este procedimiento:

Las suscripciones a SiriusXM Internet Radio se venden por separado y se rigen por las condiciones de Sirius (consulte www.sirius.com). Lea atentamente este acuerdo antes de comprar la suscripcin. Sirius, XM y todas las marcas y logotipos relacionados son marcas comerciales de Sirius XM Radio Inc. y sus filiales. Todos los derechos reservados.

Uso de SiriusXM Internet Radio (solo Norteamrica)

1 Utilice q/w para seleccionar Sign In, y luego pulse ENTER. Si ya tiene una cuenta SIRIUS, puede acceder seleccionando Sign In. Escriba su nombre de usuario y contrasea en la pantalla de teclado que aparece a continuacin o en la configuracin web. Si no sabe su nombre de usuario o la contrasea, llame a Sirius XM al nmero (888) 539-7474 para solicitar asistencia.

Consejo

Si desea utilizar mltiples cuentas de usuario, consulte Uso de mltiples cuentas ( pgina 1). Se puede iniciar sesin desde la pantalla Users.

Utilizacin de la pantalla de teclado 1. Utilice q/w/e/r y ENTER para introducir su

nombre de usuario y su contrasea. 2. Seleccione OK. 3. Pulse ENTER. Aparecer la pantalla Confirm

your entries. 4. Pulse ENTER. Aparecer Please wait... y despus la pantalla SiriusXM Internet Radio, que muestra la categora disponible para la seleccin.

2 Utilice q/w para seleccionar la categora y luego pulse ENTER. Aparece una pantalla con una lista de emisoras de la categora seleccionada.

3 Utilice q/w para seleccionar la emisora deseada y luego pulse ENTER. Aparecer la pantalla de reproduccin de la emisora seleccionada y ahora usted podr escuchar SiriusXM Internet Radio. Puede controlar las pistas con los botones del mando a distancia.

Botones activados: 2, 3, 7, 6 Elementos del men Add to My Favorites: Aade una emisora a la lista Mis favoritos.

Uso de Internet Radio

Es-5

Last.fm es un servicio musical que sabe lo que le gusta... Su nuevo receptor de AV Onkyo es muy inteligente. Si tiene una cuenta gratuita de Last.fm, har un seguimiento de todas las canciones que acaba de escuchar. Cuando visite el sitio web de Last.fm, podr ver listas personales de la msica que ha disfrutado, compartirlas con sus amigos y tambin ver lo que les gusta a ellos.

Con sus miles de biografas, crticas y una infinita variedad de emisoras de radio personalizadas y sin publicidad, Last.fm es una forma excelente de descubrir msica. Cree hoy mismo una cuenta gratuita de Last.fm en www.last.fm/join

Si se suscribe podr disfrutar de lo mejor de Last.fm Radio sin anuncios en su receptor de AV Onkyo sin necesidad de un ordenador. Recommended Radio: Descubra nuestras interesantes recomendaciones personalizadas que se adaptan a sus gustos en cada momento. Artist Radio: Escoja cualquier artista y podr escuchar una emisora de radio inspirada exclusivamente en su eleccin. My Library: Reljese y disfrute de selecciones de toda la msica que ha escuchado desde que se registr en Last.fm. Tag Radio: Polish funk? Death pop? Piense en un estilo y podr escucharlo durante horas.

Prubelo gratis ahora mismo. Cree una cuenta y ver por s mismo lo que significa tener toda la msica del mundo al alcance de sus odos. Puede consultar los precios actualizados y toda la informacin que desee en www.last.fm/subscribe

Uso del control de scrobbling Utilice q/w para seleccionar Enable, y luego pulse ENTER.

* Los servicios de radio por Internet suministrados por terceros pueden cancelarse con o sin aviso previo. Es posible que los servicios de radio por Internet no estn disponibles en algunas zonas.

Uso de Last.fm Internet Radio 1 Utilice q/w para seleccionar Sign in to your account, y luego pulse ENTER. Si ya tiene una cuenta de Last.fm, puede acceder a ella para seleccionar Sign in to your account. Introduzca su nombre de usuario y contrasea en la siguiente pantalla de teclado.

Utilizacin de la pantalla de teclado 1. Utilice q/w/e/r y ENTER para introducir su

nombre de usuario y su contrasea. 2. Seleccione OK. 3. Pulse ENTER. Aparecer la pantalla Confirm

your entries. 4. Pulse ENTER. Aparecer Please wait... y despus la pantalla Last.fm Internet Radio.

Consejo

Si desea utilizar mltiples cuentas de usuario, consulte Uso de mltiples cuentas ( pgina 1). Se puede iniciar sesin desde la pantalla Users.

2 Utilice q/w para seleccionar un men y luego pulse ENTER. Search Station: Puede buscar emisoras por artista, etiquetas o nombre de usuario. Top Artists Station: Puede reproducir canciones de los artistas mejor clasificados. Top Tags Station: Puede reproducir canciones con las etiquetas mejor clasificadas. Personal Station: Puede reproducir pistas de una emisora personalizada (Your Library, Your Neighbourhood y Your Recommendations).

Profile: Puede reproducir pistas de Recently Listened Tracks, Library y Neighbours. Account Info: Confirme los datos de su cuenta. Sign Out: Se desconecta de su cuenta.

3 Utilice q/w para seleccionar una emisora y luego pulse ENTER o 1 para iniciar la reproduccin. Se inicia la reproduccin y aparece la pantalla de reproduccin.

Elementos del men I Love this track: Se guarda la informacin sobre la cancin en el servidor de Last.fm y aumenta la frecuencia con la que se reproduce. Ban this track: Se guarda la informacin sobre la cancin en el servidor de Last.fm y se reduce la frecuencia con la que se reproduce. Add to My Favorites: Aade una emisora a la lista Mis favoritos.

Uso de Internet Radio

Es-6

Uso de Slacker Personal Radio

1 Si no tiene una cuenta, cree una en el sitio web de Slacker (www.slacker.com) con su ordenador.

Si ya tiene una cuenta de Slacker, seleccione Sign in to your account y pulse ENTER. Aparecer la pantalla de teclado. Puede introducir informacin desde el mando a distancia o desde el teclado de la unidad principal.

2 Si no hay errores en la informacin que ha introducido, utilice q/w/e/r para seleccionar OK y luego pulse ENTER. Aparecer una pantalla de confirmacin de la informacin de la cuenta.

3 Si no tiene una cuenta, seleccione Access without Sign In y pulse ENTER para utilizar una versin restringida del servicio. Tenga en cuenta que el uso estar restringido.

Consejo

Si desea utilizar mltiples cuentas de usuario, consulte Uso de mltiples cuentas ( pgina 1). Se puede iniciar sesin desde la pantalla Users.

4 Utilice q/w para seleccionar un men y luego pulse ENTER. Para salir, utilice q/w para seleccionar Sign out en esta pantalla y luego pulse ENTER.

5 Utilice q/w para seleccionar una emisora y luego pulse ENTER o 1 para iniciar la reproduccin de la emisora. Aparecer la pantalla de reproduccin.

6 Puede controlar las pistas con los botones del mando a distancia. Botones activados: 1, 3, 2, 6 Elementos del men Rate Song as Favorite: Guarda informacin en el servidor, haciendo que sea ms probable que la cancin se vuelva a reproducir. Ban Song: Guarda informacin en el servidor, haciendo que sea menos probable que la cancin se vuelva a reproducir. Ban Artist: Guarda informacin en el servidor, haciendo que sea menos probable que las canciones de este artista se vuelvan a reproducir. Mark Favorite: Aade la emisora que se est reproduciendo actualmente a los favoritos. Unmark Favorite: Elimina la emisora que se est reproduciendo actualmente de los favoritos. Add song to Library: Aade la cancin que se est reproduciendo actualmente a su biblioteca. Delete song from Library: Elimina la cancin que se est reproduciendo actualmente de la biblioteca. Add to My Favorites: Aade una emisora o cancin a la lista Mis favoritos.

SN 29401189B (C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved.

Y1203-2

* 2 9 4 0 1 1 8 9 B *

En-1

Using Internet Radio

Using Internet Radio

Note

Available services may vary depending on the region.

Common Procedures in Internet Radio Menu

1 Press NET. A list of the network services appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver.

2 Select the desired service and press ENTER. The top page of the selected service appears.

Using Multiple Accounts The AV receiver supports multiple user accounts, which means you can freely switch between several logins. After registering user accounts, login is performed from the Users screen.

Tip

Some of the services dont allow the use of multiple user accounts.

You can store up to 10 user accounts. To switch between accounts you must first log out from the

current account, and log in again on the Users screen.

1 Press MENU while the Users screen is displayed. The following menu items appear: Add new user: Remove this user: You can either store a new user account, or delete an existing one.

Using Last.fm Internet Radio ........................ 2

Using Internet Radio

En-2

Last.fm is a music service that learns what you love... Your new Onkyo AV receiver is very clever. If you have a free Last.fm account, it will keep track of all the songs youve just played. When you visit the Last.fm website, you can see personal charts of the music youve enjoyed, share them with friends and see what they like, too.

With thousands of biographies, reviews and an endless choice of personalised, ad-free radio stations, Last.fm is a great way to discover music. Pick up your free Last.fm account today at www.last.fm/join

UK and Germany only: Get a subscription and you can enjoy the best of ad-free Last.fm Radio on your Onkyo AV receiver without a computer! Recommended Radio: Discover smart personalised recommendations that adapt as your tastes change. Artist Radio: Pick any artist and well play you a whole station of music inspired by your choice. My Library: Sit back and enjoy selections from all the music youve heard since you joined Last.fm. Tag Radio: Polish funk? Death pop? Think of a style and well entertain you with it for hours.

Start your free trial straight away when you create your account and see for yourself what its like to have the worlds music at your fingertips. Latest prices and full information are available at www.last.fm/subscribe

Using scrobbling control Use q/w to select Enable, and then press ENTER.

* Internet radio services provided by a third party may be terminated with or without notice. Internet radio services may not be available in some areas.

Using Last.fm Internet Radio 1 Use q/w to select Sign in to your account, and then press ENTER. If you have the existing Last.fm account, you can sign in to your account to select Sign in to your account. Enter your user name and password in the next keyboard screen.

Using the keyboard screen 1. Use q/w/e/r and the ENTER to enter your user

name and password. 2. Select OK. 3. Press ENTER. The Confirm your entries

screen appears. 4. Press ENTER. Please wait... appears and then Last.fm Internet Radio screen appears.

Tip

If you want to use multiple user accounts, see Using Multiple Accounts ( page 1). Login can be made from the Users screen.

2 Use q/w to select menu and then press ENTER. Search Station: You can search station by Artist, Tag, or User Name. Top Artists Station: You can play tracks of top-rated artists. Top Tags Station: You can play tracks of top-rated tags. Personal Station: You can play tracks from personalized station (Your Library, Your Neighbourhood and Your Recommendations).

Profile: You can play tracks from Recently Listened Tracks, Library and Neighbours. Account Info: Confirm your account information. Sign Out: It signs out from your account.

3 Use q/w to select a station, and press ENTER or 1 to start playback. Playback starts and the playback screen appears.

Enabled buttons: 1, 2, 6

Menu Items I Love this track: Track information is saved in Last.fm server, and playback frequency increases. Ban this track: Track information is saved in Last.fm server, and playback frequency reduces. Add to My Favorites: Adds a station to My Favorites list.

Internetradio verwenden

De-1

Internetradio verwenden

Anmerkung

Die verfgbaren Dienste sind lnderabhngig verschieden.

Allgemeine Verfahren bei den Internetradio-Mens

1 Drcken Sie NET. Es erscheint eine Liste der Netzwerkdienste und die NET-Anzeige leuchtet. Wenn sie blinkt, berprfen Sie ob das Ethernet-Kabel fest im AV-Receiver eingesteckt ist.

2 Whlen Sie den gewnschten Service aus und drcken Sie ENTER. Die oberste Seite des ausgewhlten Services erscheint.

Verwendung mehrerer Konten Der AV-Receiver untersttzt mehrere Nutzerkonten, was bedeutet, dass Sie frei zwischen mehreren Logins umschalten knnen. Nach der Anmeldung der Nutzerkonten wird das Login vom Users Bildschirm aus vorgenommen.

Tipp

Einige dieser Dienstleistungen lassen keine mehrfachen Nutzerkonten zu.

Sie knnen bis zu 10 Nutzerkonten speichern. Um zwischen den Konten umzuschalten, mssen Sie sich

zuerst aus Ihrem aktuellen Konto ausloggen und sich dann wieder auf dem Users Bildschirm einloggen.

1 Drcken Sie MENU whrend der Bildschirm des Nutzers angezeigt wird. Das folgende Men erscheint: Add new user: Remove this user: Sie knnen entweder ein neues Nutzerkonto abspeichern oder ein bestehendes lschen.

Verwendung von Last.fm Internet Radio ..... 2

Internetradio verwenden

Last.fm ist ein Musikdienst, der sich Ihre Lieblingsmusik merkt... Ihr neuer Onkyo AV-Receiver ist uerst clever. Wenn Sie ein kostenloses Last.fm-Konto eingerichtet haben, werden darin alle krzlich abgespielten Titel gespeichert. Wenn Sie die Last.fm- Website besuchen, knnen Sie Ihre persnlichen Charts der von Ihnen abgespielten Musik anzeigen; teilen Sie diese mit Freunden und sehen Sie auch, welche Musik Ihre Freunde mgen.

Mit tausenden von Biografien, Rezensionen und einer schier endlosen Auswahl an persnlich angepassten, werbefreien Radiosendern ist Last.fm eine groartige Gelegenheit, um Musik zu entdecken. Holen Sie sich Ihr kostenloses Last.fm- Konto noch heute unter www.last.fm/join

Nur fr Grobritannien und Deutschland: Holen Sie sich ein Abonnement und Sie knnen auch ohne Computer die besten werbefreien Last.fm-Radiosender auf Ihrem Onkyo AV-Receiver hren! Recommended Radio: Entdecken Sie smarte, persnlich angepasste Empfehlungen, die sich mit Ihrem Musikgeschmack verndern. Artist Radio: Whlen Sie einen beliebigen Interpreten und wir spielen fr Sie einen ganzen Radiosender mit durch Ihre Wahl inspirierter Musik. My Library: Lehnen Sie sich zurck und erfreuen Sie sich an einer Auswahl aller Musik, die Sie seit Ihrer Mitgliedschaft bei Last.fm gehrt haben. Tag Radio: Polish Funk? Death Pop? Denken Sie an einen Musikstil und wir unterhalten Sie stundenlang damit.

Starten Sie Ihr kostenloses Probeabo direkt wenn Sie Ihr Konto erstellen und finden Sie selbst heraus wie es ist, jederzeit die Musik der ganzen Welt abrufen zu knnen. Die aktuellen Nutzungspreise und umfassende Infos sind unter www.last.fm/subscribe erhltlich

Scrobbling-Steuerung verwenden Verwenden Sie q/w, um Enable auszuwhlen und dann drcken Sie ENTER.

* Von Drittparteien zur Verfgung gestellte Internetradio-Dienste knnen unter Umstnden ohne Vorankndigung eingestellt werden. In bestimmten Gebieten sind Internetradio-Dienste eventuell nicht verfgbar.

Verwendung von Last.fm Internet Radio 1 Verwenden Sie q/w, um Sign in to your account auszuwhlen und dann drcken Sie ENTER. Wenn Sie ber einen bestehenden Last.fm Konto verfgen, knnen Sie sich anmelden und Sign in to your account whlen. Geben Sie Ihre Ihre Benutzernamen und das Kennwort in der folgenden Tastaturanzeige ein.

Verwendung der Tastaturanzeige 1. Verwenden Sie q/w/e/r und den ENTER, um

Ihren Nutzernamen und Passwort einzugeben. 2. Whlen Sie OK. 3. Drcken Sie ENTER. Die Anzeige Confirm

your entries erscheint. 4. Drcken Sie ENTER. Please wait... wird angezeigt und danach erscheint die Last.fm Internet Radio-Anzeige.

Tipp

Falls Sie mehrere Nutzerkonten verwenden mchten, schlagen Sie bitte unter Verwendung mehrerer Konten nach ( Seite 1). Das Login kann vom Users- Bildschirm aus erfolgen.

2 Verwenden Sie q/w, um das Men auszuwhlen und dann drcken Sie ENTER. Search Station: Sie knnen einen Sender anhand Interpreten, Tags oder Benutzernamen suchen. Top Artists Station: Sie knnen Titel der am besten bewerteten Interpreten wiedergeben. Top Tags Station: Sie knnen Titel der am besten bewerteten Tags wiedergeben. Personal Station: Sie knnen Titel aus einem persnlich angepassten Sender wiedergeben (Your Library, Your Neighbourhood und Your Recommendations).

Profile: Sie knnen Titel aus Recently Listened Tracks, Library und Neighbours wiedergeben. Account Info: Besttigen Sie Ihre Kontoinformation. Sign Out: Zur Abmeldung aus Ihrem Konto.

3 Verwenden Sie q/w, um einen Sender auszuwhlen und dann drcken Sie ENTER oder 1 , um die Wiedergabe zu starten. Die Wiedergabe wird gestartet und die Wiedergabeanzeige erscheint.

Aktivierte Tasten: 1, 2, 6 Mensymbole I Love this track: Titel-Informationen werden auf dem Last.fm-Server gespeichert und die Hufigkeit der Wiedergabe wird erhht. Ban this track: Titel-Informationen werden auf dem Last.fm-Server gespeichert und die Hufigkeit der Wiedergabe wird verringert. Add to My Favorites: Fgt einen Sender zu meiner My Favorites Liste hinzu.

SN 29401229 (C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved.

Y1112-1

* 2 9 4 0 1 2 2 9 *

Remote Control Codes

1

Remote Control Codes

/

1 While holding down the REMOTE MODE button to which you want to assign a code, press and hold down [DISPLAY] (about 3 seconds). The REMOTE MODE button/Remote indicator lights. On Integra products, button names are capitalized. For example, Remote Mode button and Display button. Notes: Remote control codes cannot be entered for [RECEIVER] and the multi zone button. Only TV remote control codes can be entered for [TV]. Except for [RECEIVER], [TV], and the multi zone button, remote control codes from any

category can be assigned for the REMOTE MODE buttons. However, these buttons also work as input selector buttons, so choose a REMOTE MODE button that corresponds with the input to which you connect your component. For example, if you connect your CD player to the CD input, choose [TV/CD] when entering its remote control code.

2 Within 30 seconds, use the number buttons to enter the 5-digit remote control code. The REMOTE MODE button/Remote indicator flashes twice. If the remote control code is not entered successfully, the REMOTE MODE button/Remote indicator will flash once slowly. Notes: The flashing element of the remote controller will differ according to your AV receivers model. The remote controller is preconfigured with remote controller presets of different components.

By entering a code from the Remote Control Code list, you can activate the relevant preset for that component.

When there are multiple codes related to one manufacturer, try and enter them one-by-one until it matches your component.

Depending on the model and year of your component, compatibility is not guaranteed. With some models, the remote controller may not not work or its compatibility may be limited

to part of the components functionality. Besides, it is not possible to add new codes to the existing remote controller presets. Though the provided remote control codes are correct at the time of printing, they are subject to

change by the manufacturer.

Remote Control Codes

2

Codes de tlcommande Cdigos de control remoto

1 Tout en maintenant enfonc le bouton REMOTE MODE auquel vous souhaitez associer un code, pressez et maintenez enfonc le bouton [DISPLAY] (pendant environ 3 secondes). Le bouton REMOTE MODE/le tmoin Remote sallume. Les noms de boutons sont en manjuscules sur les produits Integra. Par exemple, le bouton Remote Mode et le bouton Display . Remarques : Les codes de tlcommande ne peuvent pas tre entrs pour [RECEIVER] et le bouton multi

zone. Seul les code de tlcommande de tlviseurs peuvent tre entrs pour [TV]. lexception de [RECEIVER], [TV] et du bouton multi zone, vous pouvez affecter des codes

de tlcommande de nimporte quelle catgorie pour les boutons REMOTE MODE. Cependant, ces boutons font galement office de bouton de slecteur dentre : par consquent, choisissez un bouton REMOTE MODE correspondant lentre laquelle vous souhaitez raccorder votre appareil. Par exemple, si vous raccordez votre lecteur CD lentre CD, choisissez [TV/CD] lorsque vous saisissez le code de tlcommande.

2 Vous disposez de 30 secondes pour saisir le code de tlcommande cinq chiffres laide des boutons numrots. Le bouton REMOTE MODE/le tmoin Remote clignote deux fois. Si le code de tlcommande na pas t saisi correctement le bouton REMOTE MODE/lindicateur Remote ne clignote quune seule fois. Remarques : Llment clignotant de la tlcommande diffrera selon le modle de votre ampli-tuner AV. La tlcommande est prconfigure avec des prrglages de tlcommande de diffrents

appareils. En entrant un code de la liste des codes de tlcommandes, vous pouvez activer le prrglage appropri pour cet appreil.

Quand il y a de multiples codes lis un fabricant, essayez-les et entrez-les un par un jusqu ce que cela corresponde votre appareil.

Selon le modle et lanne de votre appareil, la compatibilit nest pas garantie. Avec certains modles, la tlcommande peut ne pas fonctionner ou sa compatibilit peut tre

limite une partie de la fonctionnalit de lappareil. En outre, il nest pas possible dajouter de nouveaux codes aux prrglages de tlcommande

existants. Bien que les codes de tlcommande fournis soient corrects au moment de limpression de la

liste, ils sont susceptibles dtre modifis par le fabricant.

1 Manteniendo pulsado el botn REMOTE MODE para el cual desea introducir un cdigo, pulse y mantenga presionado el botn [DISPLAY] (aproximadamente 3 segundos). Se iluminar el botn REMOTE MODE/indicador Remote. En los productos Integra, los nombres de los botones aparecen con maysculas. Por ejemplo, el botn Remote Mode y el botn Display. Notas: No podrn introducirse cdigos de mando a distancia para [RECEIVER] y el botn multizona. nicamente podrn introducirse cdigos de mando a distancia de televisor para el botn [TV]. Con la excepcin de [RECEIVER], [TV] y el botn multizona, se pueden asignar cdigos de

mando a distancia de cualquier categora a los botones de REMOTE MODE. No obstante, estos botones tambin pueden funcionar como botones de selector de entrada; por tanto, seleccione un botn REMOTE MODE que se corresponda con la entrada a la cual est conectado el componente. Por ejemplo, si conecta un reproductor de CD a la entrada de CD, seleccione [TV/CD] cuando introduzca su cdigo de mando a distancia.

2 Antes de que transcurran 30 segundos, utilice los botones numricos para introducir el cdigo de mando a distancia de 5 dgitos. El botn REMOTE MODE/indicador Remote parpadear dos veces. Si el cdigo de mando a distancia no se introduce correctamente, el botn REMOTE MODE/indicador Remote parpadear una vez despacio. Notas: El parpadeo del mando distancia ser distinto segn el modelo de receptor de AV. El mando a distancia est preconfigurado con los ajustes predeterminados de los distintos

componentes. Al introducir un cdigo de la lista de cdigos del mando a distancia se puede activar el ajuste predeterminado de ese componente.

Cuando hay mltiples cdigos relacionados con un fabricante, pruebe a introducirlos uno a uno hasta que coincida con su componente.

Dependiendo del modelo y el ao de su componente, la compatibilidad no est garantizada. Con algunos modelos, es posible que el mando a distancia no funcione o que su compatibilidad

est limitada a una parte de las funciones del componente. Adems, no es posible aadir nuevos cdigos a los ajustes predeterminados existentes del

mando a distancia. Los cdigos de mando a distancia suministrados son correctos en el momento de la impresin,

pero el fabricante puede realizar cambios.

Remote Control Codes

3

Codici del telecomando Fernbedienungscodes

1 Tenendo premuto il tasto REMOTE MODE al quale si desidera assegnare il codice, premere e tenere premuto [DISPLAY] (per circa 3 secondi). Il tasto REMOTE MODE/l'indicatore Remote si accende. Sui prodotti Integra, i nomi dei tasti sono scritti con l'iniziale maiuscola. Ad esempio, tasto Remote Mode e tasto Display. Note: I codici di controllo del telecomando non possono essere inseriti per [RECEIVER] e i tasti multi

zona. Per [TV] possibile immettere solo codici telecomando del televisore. Tranne che per [RECEIVER], [TV], e per il tasto multi zona, possibile assegnare codici di

controllo di ogni categoria per i tasti REMOTE MODE. Tuttavia, tali tasti fungono anche da tasti del selettore d'ingresso, quindi scegliere un tasto REMOTE MODE che corrisponda all'ingresso al quale viene collegato il dispositivo. Per esempio, se si collega il lettore CD all'ingresso CD, scegliere il [TV/CD] quando si immette il relativo codice telecomando.

2 Entro 30 secondi utilizzare i tasti numerici per inserire il codice telecomando a 5 cifre. Il tasto REMOTE MODE/l'indicatore Remote lampeggia due volte. Se il codice telecomando non viene inserito correttamente, il tasto REMOTE MODE/l'indicatore Remote lampeggia lentamente una volta. Note: L'elemento lampeggiante del telecomando varia a seconda del modello del ricevitore AV. Il telecomando preconfigurato con preselezioni per diversi apparecchi. Inserendo un codice

dall'elenco dei codici telecomando, possibile attivare la relativa preselezione per tale apparecchio.

Se sono presenti pi codici relativi allo stesso produttore, provare a inserirli uno a uno finch non si arrivi al codice corrispondente dell'apparecchio.

A seconda del modello e dell'anno dell'apparecchio, la compatibilit non garantita. Con alcuni modelli, il telecomando pu non funzionare o la sua compatibilit pu essere limitata

a una parte della funzionalit dell'apparecchio. Inoltre, non possibile aggiungere nuovi codici alle preselezioni esistenti del telecomando. I codici telecomando specificati sono validi alla data della stampa del presente documento, ma

sono soggetti a variazioni da parte del produttore.

1 Halten Sie die REMOTE MODE-Taste gedruckt, fur die Sie den Code eingeben mochten, und drucken Sie (ca. 3 Sekunden lang) die [DISPLAY]-Taste. Die REMOTE MODE-Taste/Remote-Anzeige leuchtet. Bei den Integra-Produkten werden die Namen der Tasten gro geschrieben. Zum Beispiel Remote Mode (Fernbedienungsmodus)-Taste und Display-Taste. Hinweise: Der Fernbedienungscode kann nicht [RECEIVER] und der Multi-Zonen-Taste zugeordnet

werden. Der Taste [TV] knnen nur Fernbedienungscodes fr einen Fernseher zugeordnet werden. Abgesehen von [RECEIVER], [TV] und der Multi-Zone-Taste, knnen die

Fernbedienungscodes jeder Kategorie den REMOTE MODE-Tasten zugewiesen werden. Allerdings dienen diese Tasten auch als Quellenwahltasten. Whlen Sie also nach Mglichkeit eine REMOTE MODE-Taste, die dem Eingang zugeordnet ist, an den Sie die betreffende Quelle angeschlossen haben. Wenn Sie z.B. einen CD-Player an den CD-Eingang anschlieen, sollten Sie [TV/CD] wenn Sie den Fernbedienungscode eingeben.

2 Geben Sie mit den Zifferntasten innerhalb von 30 Sekunden den 5-stelligen Herstellercode ein. Die REMOTE MODE-Taste/Remote-Anzeige blinkt zwei Mal. Wenn der Fernbedienungscode nicht ordnungsgem eingegeben wurde, blinkt die REMOTE MODE-Taste/Remote-Anzeige einmal langsam. Hinweise: Das blinkende Element auf der Fernbedienung unterscheidet sich je nach AV-Receiver-Modell. Die Fernbedienung ist mit den Voreinstellungen der Fernbedienung der verschiedenen

Komponenten vorkonfiguriert. Indem ein Code aus der Liste der Fernbedienungscodes eingegeben wird, knnen Sie die entsprechende Voreinstellung fr die Komponente aktivieren.

Wenn es mehrere Codes gibt, die sich auf einen Hersteller beziehen, versuchen Sie sie einzeln einzugeben, bis einer mit Ihrer Komponente bereinstimmt.

Dies hngt vom Modell und Herstellungsjahr Ihrer Komponente ab und die Kompatibilitt ist nicht garantiert.

Es kann sein, dass bei einigen Modellen die Fernbedienung nicht funktioniert oder ihre Kompatibilitt sich auf nur auf Teile der Funktionalitt der Komponente beschrnkt.

Abgesehen davon ist es nicht mglich, den bestehenden Voreinstellungen der Fernbedienung neue Codes hinzuzufgen.

Obwohl die angegebenen Fernbedienungscodes dem Stand bei Drucklegung entsprechen, sind nderungen durch den Hersteller vorbehalten.

Remote Control Codes

4

Afstandsbedieningscodes Fjrrstyrningskoder

1 Houd terwijl u de REMOTE MODE toets ingedrukt houdt waarvoor u een code wilt toewijzen de [DISPLAY] toets ingedrukt (ongeveer 3 seconden). De toets REMOTE MODE (afstandsbedieningsmodus) / Het indicatielampje afstandsbediening gaat branden. Op producten van Integra staan de namen van de toetesn in hoofdletters. Bijvoorbeeld, de toetsen Remote Mode en Display. Opmerkingen: Er kunnen geen afstandsbedieningscodes worden ingevoerd voor [RECEIVER] en de multi

zone-toets. Alleen TV afstandsbedieningscodes kunnen worden ingevoerd voor [TV]. Behalve voor [RECEIVER], [TV] en de multi zone-toets, kunnen afstandsbedieningscodes

vanuit elke categorie worden toegewezen aan de REMOTE MODE toetsen. Deze toetsen werken overigens ook als ingangsselectortoetsen, kies dus een REMOTE MODE toets die overeenkomt met de ingang waarop u uw component wilt aansluiten. Kies indien u bijvoorbeeld uw CD-speler aansluit op de CD-ingang de [TV/CD] toets bij het invoeren van de afstandsbedieningscode.

2 Gebruik binnen 30 seconden de cijfertoetsen om de 5-cijferige afstandsbedieningscode in te voeren. De toets REMOTE MODE (afstandsbedieningsmodus) / Het indicatielampje afstandsbediening knippert tweemaal. Indien de afstandsbedieningscode niet met succes wordt ingevoerd, zal de toets REMOTE MODE/Remote-indicator eenmaal traag knipperen. Opmerkingen: Het knippergedeelte van de afstandsbediening zal verschillen ten opzichte van het model van

uw AV-receiver. De afstandsbediening is voorgeprogrammeerd met voorkeuzetoetsen van verschillende

componenten. Door het invullen van een code uit de afstandsbediening codelijst kunt u de voorkeuzetoets voor die component activeren.

Wanneer er meerdere codes gerelateerd zijn aan n fabrikant, probeer deze dan een voor een totdat de juiste code overeenkomt met uw component.

Afhankelijk van het model en het bouwjaar van uw component is de compatibiliteit niet gegarandeerd.

Bij sommige modellen werkt de afstandsbediening mogelijk niet of is de compatibiliteit ervan beperkt tot een deel van de functionaliteit van de component.

Daarnaast is het niet mogelijk om nieuwe codes aan de bestaande voorkeuzetoetsen van de afstandsbediening toe te voegen.

Hoewel de gegeven afstandsbedieningscodes correct zijn op het moment van afdrukken, kunnen deze door de fabrikant gewijzigd worden.

1 Hll ned knappen fr det REMOTE MODE som du vill tilldela en kod samtidigt som du trycker och hller ned [DISPLAY] (i cirka 3 sekunder). REMOTE MODE-knapp/Fjrrindikatorlampa. P Integra-produkter, r knappnamnens begynnelsebokstav en versal. Till exempel, Fjrrlge-knapp och Display-knapp. Anmrkningar: Fjrrkontrollkoder kan inte anges fr knapparna [RECEIVER] och flerzonsknappen. Endast fjrrkontrollkoder fr tv kan anges fr [TV]. Frutom [RECEIVER], [TV] och flerzonsknappen, kan fjrrkontrollkoder fr vilken som helst

kategori tilldelas fr knapparna REMOTE MODE. Dessa knappar fungerar dock ven som ingngvljarknappar, s anvnd en knapp fr REMOTE MODE som motsvarar ingngen som du ansluter utrustningen till. Till exempel, om du ansluter din CD-spelare till CD-ingngen ska du vlja [TV/CD] nr du anger dess fjrrkontrollkod.

2 Anvnd sifferknapparna fr att ange den femsiffriga koden inom 30 sekunder. REMOTE MODE-knapp/Fjrrindikatorlampa blinkar tv gnger. Om fjrrkontrollkoden inte stlldes in, blinkar REMOTE MODE- knappen/fjrrindikatorn lngsamt en gng. Anmrkningar: Det blinkande elementet p fjrrkontrollen skiljer sig t beroende p din modell av AV-receiver. Fjrrkontrollen har frkonfigurerats med frvalda kanaler p fjrrkontrollen fr olika

komponenter. Genom att ange en kod frn fjrrkontrollkodlistan, kan du aktivera relevanta frvalda kanaler fr den utrustningen.

Nr det finns flera olika koder fr en tillverkare ska du frska att ange dem en och en tills de stmmer verens med din utrustning.

Beroende p utrustningens modell och rgng, gr det inte att garantera kompatibilitet. P vissa modeller kan det hnda att fjrrkontrollen inte fungerar eller s kan dess kompatibilitet

vara begrnsad till en del av utrustningens funktion. Dessutom gr det inte att lgga till nya koder till fjrrkontrollens existerande frvalda kanaler. ven om erhllna fjrrkontrollkoder r korrekta vid tryckningen, kan de ndras av tillverkaren.

Remote Control Codes

5

1 REMOTE MODE [DISPLAY] 3

REMOTE MODE /

Integra Remote Mode Display

[RECEIER] [TV] [RECEIVER] [TV] REMOTE MODE REMOTE MODE CD CD [TV/CD]

2 30 5

REMOTE MODE /

REMOTE MODE /

AV

1 REMOTE MODE [DISPLAY ] 3

REMOTE MODE /

Integra Remote Mode Display

[RECEIVER ]

[TV ]

[RECEIVER ][TV ] REMOTE MODE

REMOTE MODE

CD CD [TV/CD /CD]

2 30 5

REMOTE MODE /

REMOTE MODE /

AV

Remote Control Codes

6

Dedicated Onkyo Receiver Default 62503

Zone 2 62506

Zone 3 62507

Cable Set Top Box ADB 02254, 02769

Aon 02769

Arris 02187

AT&T 00858

Bright House 01376, 01877

BT Vision 02294

Cable & Wireless 01068

Cable One 01376, 01877

Cablecom 01582

Cablevision 01376, 01877

Charter 01376, 01877, 02187

Cisco 01877, 00858, 01982, 02345, 02378

Com Hem 00817, 00660, 01666, 02015, 02447

Comcast 01376, 01877, 01982, 02187

Cox 01376, 01877

Daeryung 01877

Digeo 02187

DX Antenna 01500

France Telecom 00817

Freebox 01482

Fujitsu 01497

Humax 00660, 02142, 02447, 03051, 03053

Insight 01376, 01877

J:COM 03051, 03053

Knology 01877

Kreatel 01385

Macab 00817

Mediacom 01376, 01877

mio TV 02802

Motorola 01376, 00858, 01562, 01982, 01998, 02378

Moxi 02187

NEC 01496

Neuf TV 03107

Noos 00817

NTL 01068, 01060

Numericable 02767

Ono 01068, 01562

Optus 01060

Orange 00817

Pace 01376, 01877, 01068, 01060, 01982

Panasonic 01488, 01982

Philips 00817, 01582, 02294, 02767

Pioneer 01877, 01500

RCN 01376

Rogers 01877

Sagem 00817

Samsung 01877, 01060, 01666, 02015, 02774

Scientific Atlanta 01877, 00858, 01982, 02345

SFR 03107

Shaw 01376

SingTel 01998, 02802

Sony 01460

Stofa 02015

Suddenlink 01376, 01877

Sumitomo 01500

Telewest 01068

TeliaSonera 01385

Telus 02345

Thomson 01582, 01982, 02769

Time Warner 01376, 01877, 02187

Cable Set Top Box Toshiba 01509

UPC 01582

Verizon 02378

Videotron 01877

Virgin Media 01068, 01060

Visiopass 00817

VTR 01376

WideOpenWest 01877

Ziggo 00660, 01666, 02015, 02142, 02447, 02774

Cable/PVR Combination Arris 02187

Bright House 01376, 01877

Cable One 01376, 01877

Cablevision 01376, 01877

Charter 01376, 01877, 02187

Cisco 01877, 01982

Comcast 01376, 01877, 01982, 02187

Cox 01376, 01877

Digeo 02187

Freebox 01482

Humax 02142, 03051, 03053

Insight 01376, 01877

J:COM 03051, 03053

Knology 01877

Mediacom 01376, 01877

Motorola 01376

Moxi 02187

Numericable 02767

Pace 01877

Panasonic 01982

Philips 01582, 02767

Pioneer 01877

Rogers 01877

Cable Set Top Box Samsung 01877

Scientific Atlanta 01877, 01982

Shaw 01376

Suddenlink 01376, 01877

Thomson 01582

Time Warner 01376, 01877, 02187

UPC 01582

Videotron 01877

VTR 01376

WideOpenWest 01877

Ziggo 02142

IPTV

ADB 02254, 02769

Aon 02769

AT&T 00858

BT Vision 02294

Canal+ 02657

Cisco 00858, 02345, 02378

Kreatel 01385

mio TV 02802

Motorola 01376, 00858, 01998, 02378

Neuf TV 03107

Pace 02657

Scientific Atlanta 00858, 02345

SFR 03107

SingTel 01998, 02802

TeliaSonera 01385

Telus 02345

Thomson 02769

Verizon 02378

IPTV/PVR Combination

ADB 02769

Aon 02769

Cable/PVR Combination

Remote Control Codes

7

AT&T 00858

BT Vision 02294

Cisco 00858, 02345, 02378

Kreatel 01385

Motorola 00858, 02378

Neuf TV 03107

Philips 02294

Scientific Atlanta 00858

SFR 03107

Verizon 02378

CD

Advantage 70032

AH! 70157

Aiwa 70157

Arcam 70157

Atoll Electronique 70157

Audio Research 70157

Audiolab 70157

Audiomeca 70157

Audioton 70157

AVI 70157

Balanced Audio Technology

70157

Cairn 70157

California Audio Labs 70029, 70303

Cambridge 70157

Cambridge Audio 70157

Carver 70157

CCE 70157

Cyrus 70157

Denon 70626, 70766

DKK 70000

DMX Electronics 70157

Dynaco 70157

Genexxa 70000, 70032

IPTV/PVR Combination

Goldmund 70157

Grundig 70157

Harman/Kardon 70157

Hitachi 70032

Integra 71817, 70101

JVC 70072

Kenwood 70626, 70157, 70036

Krell 70157

Linn 70157

Loewe 70157

Magnavox 70157

Marantz 70626, 70029, 70157

Matsui 70157

MCS 70029

Memorex 70032

Meridian 70157

Micromega 70157

Miro 70000

Mission 70157

Myryad 70157

NAD 70000, 70721

Naim 70157

NSM 70157

Onkyo 71817

Optimus 70000, 70032

Panasonic 70029, 70303

Philips 70626, 70157

Pioneer 70032, 70101

Polk Audio 70157

Primare 70157

Proton 70157

QED 70157

Quad 70157

Quasar 70029

Radiola 70157

RCA 70032

CD

Restek 70157

Revox 70157

Rotel 70157

SAE 70157

Sansui 70157

SAST 70157

Siemens 70157

Silsonic 70036

Simaudio 70157

Sonic Frontiers 70157

Sony 70490, 70000

Sylvania 70157

TAG McLaren 70157

Tandy 70032

Technics 70029, 70303

Thorens 70157

Thule Audio 70157

Traxdata 70626

Universum 70157

Victor 70072

Wards 70000, 70032, 70157

Yamaha 70490, 70032, 70036

Zonda 70157

CD-R

Denon 70626, 70766

JVC 70072

Kenwood 70626

Marantz 70626

Onkyo 71323

Philips 70626

Sony 70000

MD

Onkyo 70868

Sony 70490, 70000

CD

Yamaha 70490

Cassette Deck

Aiwa 40029

Arcam 40076

Audiolab 40029

Carver 40029

Denon 40076

Grundig 40029

Harman/Kardon 40029

Inkel 40070

JVC 40244

Kenwood 40070

Magnavox 40029

Marantz 40029

Myryad 40029

Onkyo 42157

Optimus 40027

Philips 40029

Pioneer 40027

Polk Audio 40029

Radiola 40029

RCA 40027

Revox 40029

Sansui 40029

Sony 40243

Thorens 40029

Victor 40244

Wards 40027, 40029

Yamaha 40097

Accessory

Apple 81115

Jamo 82228

Logitech 82182

Onkyo 82990, 81993, 82351

MD

Remote Control Codes

8

Polk Audio 82228

Video - Accessory

ADB 02254, 02769

Aon 02769

Apple 02615

AT&T 00858

BT Vision 02294

Canal+ 02657

Cisco 00858, 02345, 02378

Kreatel 01385

mio TV 02802

Motorola 01376, 00858, 01998, 02378

Neuf TV 03107

Pace 02657

Philips 02294

Scientific Atlanta 00858, 02345

SFR 03107

SingTel 01998, 02802

TeliaSonera 01385

Telus 02345

Thomson 02769

Verizon 02378

Receiver

Onkyo 52503

Satellite Set Top Box

@sat 01300

@Sky 01334

Acoustic Solutions 01284

ADB 00642, 00887, 01259

Akura 01626

Alba 01284

Allvision 01334

Accessory

Amstrad 00847, 01175, 01662, 01693

Ansonic 02418

Arnion 01300

ASCI 01334

AssCom 00853

Astro 00173, 01100

Atlanta 02418

Atsat 01300

AtSky 01334

Audiola 02418

Aurora 00879, 00642, 01433

Austar 00879, 00642, 01259

Avanit 01631

Awa 02418

Axil 01413, 01457, 02418

Axitronic 01626

Balmet 01457

Bell ExpressVu 00775

Belson 02418

Big Sat 01457

Black Diamond 01284

Blaupunkt 00173

Boshmann 01413, 01631

Boston 01251

Boxer 01458

British Sky Broadcasting

00847, 01175, 01662

BskyB 00847, 01175, 01662

Bush 01284, 01291, 01626, 01645

Canal Digital 00853, 01334

Canal Satellite 00853, 02657

Canal+ 00853, 02657

CanalSat 00853, 02657

Centrex 01457

Satellite Set Top Box

CGV 01413, 01567

Chess 01334, 01626

CityCom 01176

Clatronic 01413

Clayton 01626

Com Hem 01176, 01915

Comag 01413

Comsat 01413

Coship 01457

Crown 01284

CS 01631

Cyfra+ 01409

Cyfrowy Polsat 00853, 02527

D-box 00723, 01114

Dantax 01626

Denver 02418

Dgtec 01242, 01631, 02418

Dick Smith Electronics

02418

Digi Raum Electronics 01176

Digiality 01334

Digifusion 01645

Digihome 01284

DigiLogic 01284

DigiQuest 01300, 01457, 01631

Digisky 01457

DigitalBox 01100, 01631

Digiwave 01631

DirecTV 01377, 00099

Dish Network 00775

Dishpro 00775

DishTV 01300

DRE 01176

Dream Multimedia 01237

DSE 02280, 02418

DSTV 00879, 00642, 01433

Satellite Set Top Box

Durabrand 01284

Echostar 00775, 00853, 01323, 01409, 02527

Eco-Star 01413

Edision 01631

Elap 01413, 01567

Elbe 02418

Energy Sistem 01631, 02418

Engel 01251

EuroLine 01251

Europhon 01334

Europsat 01413, 01611

Expressvu 00775

Fagor 01611

Ferguson 01291

Finlux 01626

Fly Com 01457

FMD 01413, 01457

Foxtel 00879, 01176, 01356

Freesat 02408

Fuba 00173, 01251

Galaxis 00853, 00879

General Satellite 01176

Globo 01251, 01334, 01626

GOI 00775

Gold Box 00853

Gold Vision 01631

GoldMaster 01334

Goodmans 01284, 01291

Gradiente 00099, 00887

Grandin 01626

Grocos 01409, 01457

Grundig 00847, 00853, 00173, 00879, 01284, 01291

Haier 02418

Hallo 01626

Satellite Set Top Box

Remote Control Codes

9

Hama 01567

Hanseatic 01100

Hirschmann 00173

Hitachi 01284

Hornet 01300

HTS 00775

Humax 01377, 01176, 01427, 01675, 01808, 01882, 01915, 02144, 02408, 02616

ID Digital 01176

ID Sat 01334

ILLUSION sat 01631

Imperial 01195, 01334

Indovision 00887

iNETBOX 01237

Inno Hit 01626

Innova 00099

inVion 02418

iotronic 01413

ISkyB 00887

ITT 02418

ITT Nokia 00723

Jadeworld 00642

Jaeger 01334

JVC 00775

KabelBW 01195, 01882, 01915

Kaon 01300

Kathrein 00173, 01561, 01567

Kenwood 00853

Koenig 01631

Kreiling 01626

Kreiselmeyer 00173

L&S Electronic 01334

LaSAT 00173

Lava 01631

Satellite Set Top Box

Leiko 01626

Lemon 01334

Lenoxx 01611

Linsar 01284

Listo 01626

Lodos 01284

Logik 01284

Macab 00853

Manhattan 01300

Maspro 00173

Matsui 00173, 01284, 01626

Maximum 01334

Mediabox 00853

Mediacom 01206

MediaSat 00853

Medion 01334, 01626

MegaSat 01631

Metronic 01334, 01413, 01631, 02418

Metz 00173

Moserbaer 01251

Movistar 02527, 02761

Multichoice 00879, 00642, 01433, 02059, 02060

MySky 01356, 01693, 01850

NEOTION 01334

Netsat 00099, 00887

Nikko 00723

Nokia 00853, 00723, 01223

Nordmende 01611

NPG 01631

Onn 01284

Optex 01413, 01611, 01626

Optus 00879, 01356

Orbis 01334

Orbitech 01100, 01195

Satellite Set Top Box

Pace 00847, 00853, 00887, 01175, 01323, 01356, 01423, 01662, 01693, 01850, 02059, 02060, 02211, 02657

Pacific 01284

Palcom 01409, 01611

Panasat 00879, 01433

Panasonic 00847, 01304, 01404, 03099

Panda 00173

Pass 01567

peeKTon 01457, 02418

Philips 00099, 00853, 00173, 01114, 00887, 00133, 02211

Phoenix 02418

Pino 01334

Pioneer 00853, 01308

PMB 01611

Premiere 00723

Pro Basic 00853

Proline 01284

QNS 01404

RCA 01291

Regal 01251

Roadstar 00853

Rollmaster 01413

Rownsonic 01567

SAB 01251, 01300, 01631

Sagem 01114

Saivod 02418

Samsung 01377, 00853, 01175, 01206, 01458, 01662, 02986

Sansui 01251

Sanyo 01626

Sat Control 01300

Satellite Set Top Box

Sat Industrie 01611

SAT+ 01409

Satplus 01100

SatyCon 01631

Schaub Lorenz 02418

Schneider 01206, 01251

Schwaiger 01334, 01457, 01631

Sedea Electronique 01206, 01626

SEG 01251, 01284, 01626

Servimat 01611

ServiSat 01251

Shark 01631

Sherwood 01409

Siemens 00173, 01334, 01626, 02418

Sigmatek 02418

SKY 00099, 00847, 00887, 01175, 01662, 01693, 01850, 02754

SKY Brazil 00887

SKY Deutschland 02754

SKY Italia 00853, 01693, 01850

SKY New Zealand 02211

SKY PerfecTV! 02299, 02616, 03099

Sky XL 01251

Sky+ 01175, 01662

Skymaster 01334, 01409, 01567, 01611

Skymax 01413

Skyplus 01175, 01334

SkySat 01100

Skyvision 01334

SM Electronic 01409

Smart 01404, 01413, 01631

SmartVision 01457

Sony 00847, 00853, 01558, 02299

Satellite Set Top Box

Remote Control Codes

10

Star 00887

Stream System 01300

Strong 00853, 00879, 01284, 01300, 01409, 01626, 02418

Sunny 01300

Sunstar 00642

Supernova 00887

Supratech 01413

Systec 01334

Sytech 02418

TBoston 01251, 02418

Teac 01251

Technical 01626

Technika 01284

TechniSat 01100, 01195

Technosat 01206

Techwood 01251, 01284, 01626

TELE System 01251, 01409, 01611

Telefonica 02527, 02761

Telestar 01100, 01195, 01251, 01334, 01626

Televes 01300, 01334

Televisa 00887

Tevion 01409

Thomson 00847, 00853, 01175, 01046, 01291, 01662

Tonna 01611

Topfield 01206

Toshiba 01284

Trevi 01251

Triax 00853, 01251, 01291, 01413, 01611, 01626, 01631

Tricolor TV 01176

True Visions 02408

Twinner 01611

Satellite Set Top Box

UBC 00642

UEC 00879, 01356

United 01251, 01626, 02418

Unitymedia 01882

Universum 00173, 01251

Variosat 00173

VEA 02418

Vestel 01251, 01284

Viasat 01195

Vision 01626

Visiosat 01413, 01457

Vitecom 01413

Vivax 02418

Volcasat 02418

Wavelength 01413

Wharfedale 01284

Wisi 00173

Worldsat 01251

Woxter 02418

Xsat 00847, 01323

Xtreme 01300

Yakumo 01413

Yes 00887

Zehnder 01251, 01334, 01413, 01631

Zinwell 02280, 02761

Satellite Set Top Box

@sat 01300

SAT/PVR Combination

@sat 01300

Amstrad 01175, 01662, 01693

Atsat 01300

Bell ExpressVu 00775

British Sky Broadcasting

01175, 01662

Satellite Set Top Box

BskyB 01175, 01662

Bush 01645

Canal Satellite 02657

Canal+ 02657

CanalSat 02657

Cyfrowy Polsat 02527

Digifusion 01645

DigiQuest 01300

DirecTV 01377, 00099, 20739

Dish Network 00775

Dishpro 00775

Dream Multimedia 01237

Echostar 00775, 02527

Edision 01631

Expressvu 00775

Foxtel 01356

Humax 01176, 01427, 01675, 01808

ID Sat 01334

iNETBOX 01237

Kaon 01300

Kathrein 01561

Maximum 01334

Mediacom 01206

MegaSat 01631

Movistar 02527

Multichoice 02059, 02060

MySky 01356, 01693, 01850

NEOTION 01334

Pace 01175, 01356, 01423, 01662, 01693, 01850, 02059, 02060, 02211, 02657

Panasonic 01304, 03099

Philips 00099

Samsung 01175, 01206, 01662

Sat Control 01300

SAT/PVR Combination

Schneider 01206

Sedea Electronique 01206

SKY 01175, 01662, 01693, 01850, 02754

SKY Deutschland 02754

SKY Italia 01693, 01850

SKY New Zealand 02211

SKY PerfecTV! 02299, 03099

Sky+ 01662

Skyplus 01175, 01334

Smart 01631

Sony 02299

Stream System 01300

Strong 01300

Sunny 01300

TechniSat 01195

Technosat 01206

Telefonica 02527

Telestar 01195

Thomson 01175, 01662

Topfield 01206

Viasat 01195

Xtreme 01300

Television

A.R. Systems 10556, 10037

Accent 10037

Acer 11339

Acoustic Solutions 11037, 11667

Action 10650

Addison 10653

AEG 11037, 11324

Agfaphoto 12719

Aiko 10037

Aim 10037, 10499

SAT/PVR Combination

Remote Control Codes

11

Akai 10178, 10556, 10037, 10714, 10715, 10208, 11675

Akiba 10037

Akito 10037

Akura 10171, 10037, 10714, 10668, 11037, 11363, 11585, 11667, 11709

Alba 10037, 10714, 10668, 11037, 11585

Alien 11037

Allstar 10037

Amstrad 10171, 10037, 11037

Anam 10037

Anam National 10037, 10650

Andersson 11585

Anitech 10037

Ansonic 10037, 10668

AOC 10178, 10625, 11365

Ardem 10037, 10714

Arena 10037

Aristona 10556, 10037

ART 11037

Art Mito 11585

Asberg 10037

Astra 10037

ATD 10698

Atlantic 10037

Audiosonic 10037, 10714, 10715

Audiovox 11564

Audioworld 10698

Aventura 10171

Axxon 10714

Baird 10208

Bang & Olufsen 10565

Barco 10556

Television

Basic Line 10556, 10037, 10668, 11037

Baur 10037, 10195, 10512

Beaumark 10178

Beijing 10208

Beko 10037, 10714, 10715, 11652

Belson 10698

Belstar 11037

Beon 10037

Berthen 10556, 10668

Bestar 10037

Bexa 12493

Black Diamond 11037

Blaupunkt 10195

Blue Sky 10556, 10037, 10625, 10714, 10668, 11037, 10715, 10499, 11324, 11363, 11652, 11709

Boca 11652

Boman 11324

Bork 11363

BPL 10037, 10208

Brandt 10625, 10714, 10560

Brimax 11709

Brinkmann 10037, 10668

Brionvega 10037

Bush 10556, 10037, 10714, 10668, 11037, 10698, 10208, 11585, 11652, 11667, 12719

Byd:sign 12140, 12209

Camper 10037

Carad 10668, 11037

Carena 10037

Carrefour 10037

Cascade 10037

Television

Casio 10037

Cathay 10037

CCE 10037

Centrum 11037

Centurion 10037

Changhong 10508

Chimei 11666

Clarivox 10037

Classic 10499

Clatronic 10037, 10714, 11324

Clayton 11037

Condor 10037

Conrowa 10698

Contec 10037

Cosmel 10037

CPTEC 10625, 11363

Crown 10037, 10714, 10668, 11037, 10715, 10208, 11652

Cyberpix 11667

D-Vision 10556, 10037

Daewoo 10178, 10556, 10037, 10634, 10499, 12098

Dansai 10037, 10208

Dantax 10714, 11037, 10715, 11652

Datsura 10208

Dawa 10037

Daytron 10037

De Graaf 10208

DEC 11709

Decca 10037

Denver 10037, 11709

Desmet 10037

Diamant 10037

Diamond 10698

Television

Dick Smith Electronics

10698

Digatron 10037

Digihome 11667

Digiline 10037, 10668

Digitek 11709

Digitor 10037, 10698

Dixi 10037

DL 11363

DMTech 12001

Domeos 10668

Drean 10037

DSE 10698

Dual 10037, 11037, 11585, 11667

Durabrand 10178, 10171, 10714, 11037, 11652

Dux 10037

DX Antenna 11817, 13817

Dynatron 10037

Dynex 12049

e-motion 11709

E:max 11324

Easy Living 11666, 11709

ECE 10037

Elbe 10556, 10037

Electrograph 11755

Element 11886

Elfunk 11037

ELG 10037

Elin 10037

Elite 10037

Emerson 10178, 10171, 10037, 10714, 10668, 11394, 11864, 11886

Envision 11365, 11506

Epson 11379

Television

Remote Control Codes

12

Erres 10037

ESA 10171

ESC 10037

Euroman 10037

Europa 10037

Europhon 10037

Evesham 11248, 11667

Excello 11037

Exquisit 10037

Ferguson 10037, 10625, 10560, 10195, 11037, 11585

Fidelity 10171, 10037, 10512

Finlandia 10208

Finlux 10556, 10037, 10714, 10715, 11248, 11667

Firstline 10556, 10037, 10714, 10668, 11037, 10208, 11363

Fisher 10208

Flint 10037

Formenti 10037

Fraba 10037

Friac 10037, 10499

Fujicom 11709

Fujitsu 10809

Fujitsu Siemens 10809, 11248, 11666

Funai 10171, 10714, 10668, 11037, 11394, 11666, 11817, 13817

G-Hanz 11363

Gaba 11037

Galaxi 10037

Galaxis 10037

Gateway 11755

GE 10178, 11454, 10625, 10560

GEC 10037

Television

Genesis 10037

Genexxa 10037

GFM 10171, 11864, 11886

Godrej 11585

Goldfunk 10668

GoldStar 10178, 10037, 10714, 10715

Goodmans 10556, 10037, 10625, 10714, 10560, 10668, 10634, 11037, 10499, 11585, 11667

Gorenje 11585

Gradiente 10037

Graetz 10714

Granada 10037, 10560, 10208

Grandin 10556, 10037, 10714, 10668, 11037, 10715, 11652

Grundig 10556, 10037, 10195, 11223, 11667, 12625

GVA 11363, 12098

H & B 12001

Haier 10037, 10698, 10508

Hallmark 10178

Hankook 10178

Hanseatic 10556, 10037, 10625, 10714, 10634, 10499, 12001

Hantarex 10037

Hantor 10037

Harwood 10037

Hauppauge 10037

HB 11324

HCM 10037

Highline 10037

Hinari 10037, 10208

Hisawa 10714

Television

Hisense 10556, 10508, 10208, 11363, 12098

Hitachi 10150, 10178, 10037, 10634, 11037, 10508, 10499, 10578, 11576, 11585, 11643, 11667, 11691, 12433

Hitachi Fujian 10150

Hitec 10698

Hoeher 10714

Hornyphon 10037

Hugoson 11666

Humax 11295

Hypson 10556, 10037, 10714, 10668, 11037, 10715

Hyundai 11037, 10698

Iberia 10037

ICE 10037

iLo 11394

Imperial 10037

Indiana 10037

Ingelen 10714

Inno Hit 11037, 11585

Innova 10037

Insignia 10171, 11423, 11564, 12049

Integra 11807, 13100, 13500

Interbuy 10037

Interfunk 10037, 10512

Internal 10556

Intervision 10037

Irradio 10037

IRT 10698

Isukai 10037

ITS 10037

ITT 10208

ITT Nokia 10208

Television

ITV 10037

JGC 11709

Jinfeng 10208

Jinxing 10556, 10037, 10698

JMB 10556, 10634, 10499

Jubilee 10556

JVC 10650, 10653, 10508, 11428, 11601, 12271

Kaisui 10037

Karcher 10714, 11324

Kathrein 10556

Kendo 10037, 11037, 11585

Kennex 11037

Kioto 10556

Kiton 10037, 10668

KLL 10037

Kneissel 10556, 10037, 10499

Koenig 10037

Kolin 10150, 10037, 11610, 11755

Kolster 10037

Konka 10037, 10714

Korpel 10037

Kosmos 10037

Kunlun 10208

L&S Electronic 10714

Lavic 11363

Lavis 11037

Lecson 10037

Lenco 10037, 11037

Leyco 10037

LG 10178, 10556, 10037, 10714, 10715, 10698, 11423, 11768, 11840, 12182, 12358, 12424, 12834

Liesenkoetter 10037

Television

Remote Control Codes

13

Lifetec 10037, 10714, 10668, 11037, 12001

Linsar 11585

Local India TV 10208

Local Malaysia TV 10698

Lodos 11037

Loewe 10037, 10512, 11884

Logik 11037, 10698

Logix 10668

Luma 11037

Lumatron 10037, 10668

Lumenio 10037

Lux May 10037

Luxor 11037, 10208

LXI 10178

M Electronic 10037, 10714, 10634, 10195, 10512, 11652

Madison 10037

Magnavox 10171, 11454, 11365, 11506, 11755, 11867, 12372

Magnum 10037, 10714, 10715

Manesth 10037

Manhattan 10037, 10668, 11037

Marantz 11454, 10556, 10037

Mark 10037, 10714, 10715

Master's 10499

Mastro 10698

Masuda 10037

Matsui 10556, 10037, 10714, 10195, 11037, 10208, 11666, 11667

Matsushita 10650

Maxent 11755

Maxess 12493

Meck 10698

Mediator 10556, 10037

Television

Medion 10556, 10037, 10714, 10668, 11037, 10698, 10512, 11248, 11585, 11667, 12001, 12719

Megatron 10178

MEI 11037

Memorex 10150, 10178, 11037

Mercury 10037

Mermaid 10037

Metronic 10625

Metz 10037, 10668, 10195, 11037, 11533

MGA 10150, 10178

Micromaxx 10037, 10714, 10668, 11037, 11324, 12001

Microspot 11614

Mikomi 11037, 11585

Minato 10037

Minerva 10195, 11248

Ministry Of Sound 11667

Minoka 10037

Mirai 11666

Mitsubishi 10150, 11250, 10178, 10556, 10037, 11037, 10512, 11171

Mivar 10609

Moree 10037

Morgan's 10037

Moserbaer 11585

MTC 10512

MTlogic 10714

Mudan 10208

Multitec 10037, 10668, 11037

Multitech 10037

Myrica 11666

Myryad 10556

NAD 10178, 10037

Television

Naiko 10037

Nakimura 10037

National 10508, 10208

NEC 10178, 10653, 10508, 10499

Neckermann 10556, 10037

NEI 10037, 11037

NEO 11324

Netsat 10037

NetTV 11755

Neufunk 10556, 10037, 10714

New Tech 10556, 10037

Newave 10178

Nikkai 10037

Nikkei 10714

Nikko 10178

Nokia 10208

Norcent 11365

Nordmende 10037, 10714, 10560, 10195, 11585, 11667, 12001

Normerel 10037

Nortek 10668

Novatronic 10037

Novita 11585

Nu-Tec 10698

O.K.Line 11037, 11324

Oceanic 10208

Odys 12719

Okano 10037

OKI 11585, 11667

Olevia 11610, 12124

Omni 10698

Onei 11667

Onida 10653

Onimax 10714

Television

Onix 10698

Onkyo 11807, 13100, 13500

Onn 11667, 11709

Onyx 11709

Opera 10037, 10714

Optimus 10650

Orbit 10037

Orion 10556, 10037, 10714, 11037, 12001

Orline 10037

Ormond 10668, 11037

Osaki 10556, 10037

Osio 10037

Osume 10037

Otto Versand 10556, 10037, 10195, 10512

Pacific 10556, 10714, 11037, 11324

Palladium 10556, 10037, 10714

Palsonic 10037, 10698

Panama 10037

Panasonic 11480, 10037, 10650, 10508, 10208, 11636, 12170

Panavision 10037

Panda 10698, 10508, 10208

Pansonic 11636

Penney 10178

Perdio 10037

Perfekt 10037

Petters 10037

Philco 10178, 10171, 10037, 11394

Philips 10178, 10171, 11454, 10556, 10037, 10512, 10605, 10690, 11394, 11506, 11867, 12372

Phocus 10714, 11652

Television

Remote Control Codes

14

Phoenix 10037

Phonola 10556, 10037

Pioneer 10037, 10698, 10512, 11457, 11636, 12171

Plantron 10037

Playsonic 10037, 10714, 10715, 11652

Powerpoint 10037, 10698

Prinston 11037, 10715

Profitronic 10037

Proline 10037, 10625, 10634, 11037

Prosonic 10037, 10714, 10668, 11324, 11585, 11667, 11709, 12001

Protech 10037, 10668, 11037

Proton 10178

ProVision 10556, 10037, 10714, 11324

Pvision 12001

Pye 10556, 10037

Qingdao 10208

Quasar 10650

Quelle 10037, 10668, 10195, 11037, 10512

R-Line 10037

Radiola 10556, 10037

Radiomarelli 10037

RadioShack 10178, 10037

Radiotone 10037, 10668, 11037

RCA 10178, 11454, 10625, 10560, 10618, 11781, 12247, 12403, 12429, 12434, 12746, 12932

Realistic 10178

Recor 10037

Rectiligne 10037

Redstar 10037

Television

Reflex 10037, 10668, 11037

Relisys 11585

Remotec 10171, 10037

Reoc 10714

Revox 10037

RFT 10037

Roadstar 10037, 10714, 10668, 11037, 10715

Rolson 12001, 12098

Rowa 10037, 10698

Saba 10625, 10714, 10560

Sagem 10618

Saivod 10037, 10668, 11037

Salora 10208, 12001

Sampo 10178, 10171, 10650, 11755

Samsung 10178, 10556, 10037, 10618, 10650, 10208, 12051

Sansui 10171, 10037, 10714, 11248, 12001

Sanyo 11037, 10508, 10208, 11142, 11365, 11585, 11667, 11974

SBR 10556, 10037

Schaub Lorenz 10714, 11324, 11363, 11667, 12001

Schneider 10556, 10037, 10714, 10668, 11037

Schoentech 11037

Scotch 10178

Scott 10178

Sears 10178, 10171

Seaway 10634

Seelver 11037

SEG 10037, 10668, 11037, 12719

SEI 10037

Television

Sei-Sinudyne 10037

Serie Dorada 10178

Shanghai 10208

Sharp 10650, 10818, 11165, 11423, 11659

Shintoshi 10037

Shivaki 10178, 10037

Siam 10037

Siemens 10037, 10195

Siera 10556, 10037

Silva 10037

Silva Schneider 10037

Silver 10715

SilverCrest 11037

Sinudyne 10037

SKY 10037, 11614, 11775

Skyworth 10037, 10698

Sliding 11324

SLX 10668

Solavox 10037

Soniko 10037

Soniq 12493

Sonitron 10208

Sonneclair 10037

Sonoko 10037

Sonolor 10208

Sontec 10037

Sony 10810, 11505, 11167, 11651, 11825

Soundesign 10178

Soundwave 10037, 11037, 10715

Sowa 10178

Squareview 10171

Standard 10037, 11037, 11709

Starlite 10037

Strato 10037

Television

SunBriteTV 11610

Sungoo 11248

Sunny 10037

Sunstar 10037

Sunstech 12001

Sunwood 10037

Supersonic 10208

SuperTech 10556, 10037

Supra 10178

Svasa 10208

Swisstec 11614, 11775

Sylvania 10171, 11394, 11864, 11886

Symphonic 10171, 11394

Synco 10178, 11755

Syntax 11610

Sysline 10037

Tacico 10178

Talent 10178

Tashiko 10650

Tatung 10037, 11248, 11324

TCL 10698, 12403, 12429, 12434, 13183

TCM 10714, 12001

Teac 10178, 10171, 10037, 10714, 10668, 11037, 10698, 10512, 11248, 11363, 11709, 11755

Tec 10037

Tech Line 10037, 10668

Technica 11037

Technics 10556, 10650

Technika 11667

TechniSat 10556

Technisson 10714, 11652

Techno 11585

Television

Remote Control Codes

15

Technosonic 10556, 10625, 10499, 11324

Techvision 11709

Techwood 11037, 11667

Tecnimagen 10556

Teco 10178, 10653

Tedelex 10208, 11709

Teknika 10150

TELE System 11585

Telecor 10037

Telefunken 10037, 10625, 10714, 10560, 10698, 11585, 11667

Telefusion 10037

Telegazi 10037

Telemeister 10037

Telesonic 10037

Telestar 10556, 10037

Teletech 10037, 10668, 11037

Teleview 10037

Tennessee 10037

Tensai 10037, 11037, 10715

Tesla 10556, 10037, 10714, 11037, 11652

Tevion 10556, 10037, 10714, 10668, 11037, 11248, 11585, 11667

Thomson 10037, 10625, 10560

Thorn 10037, 10499, 10512

Thorn-Ferguson 10499

TMK 10178

Tokai 10037, 10668, 11037

Tokaido 11037

Topline 10668, 11037

Toshiba 10195, 11037, 10618, 10650, 10508, 11169, 11508, 11524, 11652, 12203

Television

Toyoda 11709

TRANS-continents 10556, 10037, 10668, 11037

Transonic 10037, 10698, 10512, 11363

Triad 10556

Trio 11248

Triumph 10556, 10037

TVTEXT 95 10556

Uher 10037

Ultravox 10037

UMC 11614, 11775

Unic Line 10037

Uniden 12122

United 10556, 10037, 10714, 11037, 10715, 11652

Unitek 11709

Universal 10037, 10714

Universum 10037, 10668, 10195, 11037, 10618, 10512

Univox 10037

V7 Videoseven 11666, 11755

Vestel 10037, 10668, 11037, 11585, 11667

Vexa 10037

Victor 10650, 10653, 11428

Videocon 10037, 10508

VideoSystem 10037

Vidtech 10178

Viewsonic 11365, 11564, 11755, 12049

Vision 10037

Vistron 11363

Vivax 11709

Vizio 11758, 12209

Vortec 10037

Voxson 10178, 10037

Television

VU 11365, 12098

Walker 11667

Waltham 10037, 10668, 11037

Wansa 12098

Wards 10178

Watson 10037, 10714, 10668, 11037

Wega 10037

Welltech 10714, 11652

Weltstar 11037

Westinghouse 11755

Wharfedale 10556, 10037, 11324, 11667

White Westinghouse 10037

Wilson 10556

Windsor 10668, 11037

Windy Sam 10556

Wintel 10714

World-of-Vision 12001

Wyse 11365

Xenius 10634

Xiahua 10698

XLogic 10698

Xrypton 10037

Yamaha 10650, 11576

Yamishi 10037

Yokan 10037

Yoko 10037

YU-MA-TU 10037

Zenith 10178, 10037, 11365, 11423, 12358

Zepto 11585

Zonda 10698

VCR

DirecTV 20739

Go Video 20614

Television

Humax 20739

Panasonic 20614, 20616

Philips 20739

ReplayTV 20614, 20616

Sonic Blue 20614, 20616

Sony 20636

TiVo 20636, 20739

PVR

DirecTV 20739

Go Video 20614

Humax 20739

Panasonic 20614, 20616

Philips 20739

ReplayTV 20614, 20616

Sonic Blue 20614, 20616

Sony 20636

TiVo 20636, 20739

TV/VCR Combination

Amstrad 10171

Ferguson 10625

Fidelity 10171

GoldStar 10037

Grundig 10556, 10037, 10195

LG 10178

Mitsubishi 10556

Philips 10556, 10037

Radiola 10556

Saba 10625

Sanyo 11974

Schneider 10556, 10037

Sharp 10818

Siemens 10037

Sony 11505

Teac 10178, 10171

VCR

Remote Control Codes

16

Technics 10556

Thomson 10625

DVD

3D LAB 30539

Accurian 30675

Acoustic Solutions 30713

AEG 30675

AFK 31152

Aiwa 30533

Akai 30675

Alba 30539, 30713

Ambiance 33052

Amstrad 30713

Anthem 32820

Aristona 30539, 30646

ASDA 32213

Audix 30713

Autovox 30713

Awa 32587

Basic Line 30713

Bel Canto Design 31571

Black Diamond 30713

Blue Parade 30571

Blue Sky 30713

Brandt 30503

Bush 30713

C-Tech 31152

California Audio Labs 30490

Cambridge Audio 32808

Centrum 30675, 30713

Changhong 30627

Cinetec 30713

Clatronic 30675

Clayton 30713

Crown 30713

TV/VCR Combination

Dantax 30539, 30713

Denon 30490, 30634, 31634, 32258, 32748

Dick Smith Electronics

31152

Digihome 30713

DigiLogic 30713

Digix Media 31394

Disney 30675

DSE 30675, 31152

Dual 30713

Durabrand 30675, 30713

Dynex 32596

Dyon 33052

eBench 31152

Elfunk 30713

Elite 31152

Emerson 30675, 32213

EuroLine 30675

Ferguson 30713

Finlux 30741

Firstline 30713

Foehn & Hirsch 33052

Funai 30675

GE 30522

GFM 30675

Global Sphere 31152

Go Video 30741

GoldStar 30741

Goodmans 30713, 31152

GPX 30741

Grandin 30713

Grundig 30539, 30713

H & B 30713

Haaz 31152

Hanseatic 30741

DVD

Harman/Kardon 30582, 31229, 33228

Henss 30713

Hitachi 30573, 30713, 31664

Hoeher 30713

HotMedia 31152

Humax 30646

Inno Hit 30713

Insignia 30741, 30675, 32428, 32596

Integra 30503, 30571, 30627, 31612, 31634, 32147

Irradio 30646

JVC 30503, 30539, 30623, 30867, 31597, 31602, 32855

Kendo 30713

Kennex 30713

Kenwood 30490, 30534

Lenco 30713, 33052

Lexicon 32545

LG 30741, 31602

Limit 33052

Lodos 30713

Loewe 30539, 30741, 32474, 32783

Logik 30713

Lumatron 30741, 30713

Lunatron 30741

Luxman 30573

Luxor 30713

Magnavox 30503, 30539, 30646, 30675, 30713, 31354

Manhattan 30713

Marantz 30539, 32414, 32432, 33444

Mark 30713

Matsui 30713

DVD

Maxim 30713

MDS 30713

Medion 30630, 30741

Memorex 32213

Metz 30571, 30713

Micromedia 30503, 30539

Micromega 30539

Microsoft 30522, 32083

Minax 30713

Mitsubishi 30713

Momitsu 33052

NAD 30741

NEC 30741, 31602

Onkyo 30503, 30627, 31612, 32147, 30571, 31634

Oppo 30575, 32545

Orion 30713

Ormond 30713

Pacific 30713

Palladium 30713

Panasonic 30503, 30490, 31579, 31641, 32523, 32710, 32859

Pelican Accessories 30533

Philco 30675

Philips 30503, 30539, 30646, 30675, 30713, 31340, 31354, 32056, 32084, 32434, 32689

Pioneer 30571, 30142, 30631, 31571, 32442, 32860

Polk Audio 30539

Presidian 30675

ProAudio 31394

Proscan 30522

Proson 30713

Pye 30539, 30646

DVD

Remote Control Codes

17

Radionette 30741

Radiotone 30713

RCA 30522, 30571, 32213, 32587

REC 30490

Red 32213

Redstar 31394

Roadstar 30713

Rotel 30623

Salora 30741

Samsung 30490, 30573, 30199, 30820, 31635, 32069, 32329, 32489, 33195

Sanyo 30713

Schneider 30539, 30646, 30713

Schoentech 30713

Scott 31394

SEG 30713

Semp 30503

Sharp 30630, 30675, 30713, 32250, 32474, 32652, 32869

Sherwood 30741, 33052

Shinsonic 30533

Silva Schneider 30741

SilverCrest 31152

Skantic 30539, 30713

SM Electronic 31152

Smart 30713

Sony 30533, 30864, 31033, 31070, 31431, 31516, 31633, 32180

Soundwave 30713

Star Clusters 31152

Strato 31152

Strong 30713

Supervision 31152

DVD

Sylvania 30630, 30675

Symphonic 30675

Tamashi 31394

Tandberg 30713

Targa 30741

Tchibo 30741

TCL 32587

TCM 30741

Teac 30571, 30741, 30675, 31394

Technica 30713

Technics 30490

Techwood 30713

Teletech 30713

Theta Digital 30571

Thomson 30522

Toshiba 30503, 31639, 32277, 32551, 32705, 33157

Transonic 31394

TVE 30713

United 30675, 30713, 31152

Universum 30741, 30713

Urban Concepts 30503

Vestel 30713

Victor 31597

Vizio 32563

Vtrek 32587

Waltham 30713

Wellington 30713

Weltstar 30713

Wharfedale 30713

Windsor 30713

Windy Sam 30573

Xbox 30522, 32083

XLogic 31152

DVD

Yamaha 30490, 30539, 30646, 30817, 31354, 32298, 32299

Zenith 30503, 30741

Blu-ray Disc

Ambiance 33052

Anthem 32820

Cambridge Audio 32808

Denon 32258, 32748

Dyon 33052

Foehn & Hirsch 33052

Funai 30675

Harman/Kardon 33228

Insignia 30675, 32428, 32596

Integra 32147, 32900, 32910, 33100, 33101, 33500, 33501

JVC 32855

Lenco 33052

Lexicon 32545

LG 30741, 31602

Limit 33052

Loewe 32474, 32783

Magnavox 30675

Marantz 32414, 32432, 33444

Momitsu 33052

Onkyo 32147, 32900, 32910, 33100, 33101, 33500, 33501

Oppo 32545

Panasonic 31641, 32523, 32859

Philips 32084, 32434, 32689

Pioneer 30142, 32442

Samsung 30199, 33195

Sharp 32250, 32474, 32652

Sherwood 33052

DVD

Sony 31516, 32180

Sylvania 30675

Toshiba 32551, 32705, 33157

Vizio 32563

Yamaha 32298, 32299

DVD-R

Accurian 30675

Aristona 30646

Denon 30490

Emerson 30675

Funai 30675

Go Video 30741

GPX 30741

Hitachi 31664

Humax 30646

Irradio 30646

JVC 31597

LG 30741

Loewe 30741

Magnavox 30646, 30675

Medion 30741

Panasonic 30490, 31579, 32523, 32710, 32859

Philips 30646, 31340

Pioneer 30631, 32860

Pye 30646

RCA 30522

Samsung 30490, 31635

Schneider 30646

Sharp 30630, 30675, 32869

Sony 31033, 31070, 31431, 31516, 31633, 32180

Sylvania 30675

Targa 30741

Toshiba 31639, 32277, 32551

Blu-ray Disc

Remote Control Codes

18

Victor 31597

Yamaha 30646

Zenith 30741

HD-DVD

Integra 32901, 33104 33504

LG 30741

Microsoft 32083

Onkyo 32901, 33104 33504

Xbox 32083

TV/DVD Combination

Akai 11675

Black Diamond 11037, 30713

Blue Sky 11037, 30713

Bush 11037, 10698, 12719, 30713

Centrum 11037, 30713

Crown 11037, 30713

DMTech 12001

Dual 11037, 30713

Dynex 12049

Elfunk 11037, 30713

Emerson 11394, 11864, 11886, 30675

Ferguson 11037, 30713

Goodmans 11037, 30713

Grandin 30713

Grundig 30539

H & B 12001

Hanseatic 12001

Hitachi 11037, 11667, 30713

Insignia 12049

JVC 12271

LG 11423

Logik 11037, 30713

Luxor 11037, 30713

DVD-R

Magnavox 12372

Matsui 11037, 30713

Medion 12719

Nordmende 12001

Odys 12719

Panasonic 12170

Philips 11454, 10556, 11394, 30539

Powerpoint 10698

Prosonic 12001

Pvision 12001

RCA 12746, 12932

Schaub Lorenz 12001

SEG 11037, 12719, 30713

Sharp 10818

Soniq 12493

Sunstech 12001

Sylvania 10171, 11394, 11864, 11886, 30630, 30675

Teac 10698

Technica 11037, 30713

Telefunken 10698

Teletech 11037, 30713

Thomson 10625

Toshiba 11524

United 11037, 30713

Universum 30713

Vestel 11037

Viewsonic 12049

Weltstar 11037,

Manualsnet FAQs

If you want to find out how the HT RC460 Onkyo works, you can view and download the Onkyo HT RC460 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Onkyo HT RC460 as well as other Onkyo manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Onkyo HT RC460. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Onkyo HT RC460 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Onkyo HT RC460 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Onkyo HT RC460 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Onkyo HT RC460 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Onkyo HT RC460 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.