Contents

Onkyo C 7000R Instruction Manual PDF

1 of 36
1 of 36

Summary of Content for Onkyo C 7000R Instruction Manual PDF

Compact Disc Player

C-7000R

Instruction Manual En

2 En

Introduction

Important Safety Instructions

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in

accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen

into the apparatus, C. If the apparatus has been exposed to rain or water, D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often

require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in any way, and

F. When the apparatus exhibits a distinct change in performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Dont put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING RISK OF ELECTRIC SHOCK

DO NOT OPEN RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

AVIS

PORTABLE CART WARNING

S3125A

3 En

Precautions 1. Recording CopyrightUnless its for personal use

only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC FuseThe AC fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. CareOccasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Dont use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the units rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

Some models have a voltage selector switch for compatibility with power systems around the world. Before you plug in such a model, make sure that the voltage selector is set to the correct voltage for your area.

Pressing the [POWER] button to select OFF mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Preventing Hearing Loss Caution Excessive sound pressure from earphones and headphones can cause hearing loss.

6. Batteries and Heat Exposure Warning Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.

7. Never Touch this Unit with Wet HandsNever handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

8. Handling Notes If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case.

This units top and rear panels may get warm after prolonged use. This is normal.

If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

When youve finished using this unit, remove all discs and turn off the power.

9. Installing this Unit Install this unit in a well-ventilated location. Ensure that theres adequate ventilation all around

this unit, especially if its installed in an audio rack. If the ventilation is inadequate, the unit may overheat, leading to malfunction.

Do not expose this unit to direct sunlight or heat sources, because its internal temperature may rise, shortening the life of the optical pickup.

Avoid damp and dusty places, and places subject to vibrations from loudspeakers. Never put the unit on top of, or directly above a loudspeaker.

Install this unit horizontally. Never use it on its side or on a sloping surface, because it may cause a malfunction.

If you install this unit near a TV, radio, or VCR, the picture and sound quality may be affected. If this occurs, move this unit away from the TV, radio, or VCR.

10. Moisture Condensation Moisture condensation may damage this unit. Read the following carefully: Moisture may condense on the lens of the optical pickup, one of the most important parts inside this unit. Moisture condensation can occur in the following

situations: The unit is moved from a cold place to a warm

place. A heater is turned on, or cold air from an air

conditioner is hitting the unit. In the summer, when this unit is moved from an

air conditioned room to a hot and humid place. The unit is used in a humid place.

Do not use this unit when theres the possibility of moisture condensation occurring. Doing so may damage your discs and certain parts inside this unit.

If condensation does occur, unplug the power cord and leave the unit for two to three hours in the room temperature.

4 En

This unit contains a semiconductor laser system and is classified as a CLASS 1 LASER PRODUCT. So, to use this model properly, read this Instruction Manual carefully. In case of any trouble, please contact the store where you purchased the unit. To prevent being exposed to the laser beam, do not try to open the enclosure.

CAUTION: CLASS 1M VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

The label on the right is applied on the rear panel.

1. This unit is a CLASS 1 LASER PRODUCT and employs a laser inside the cabinet.

2. To prevent the laser from being exposed, do not remove the cover. Refer servicing to qualified personnel.

For U.S. models FCC Information for User

CAUTION: The user changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and

receiver. Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV

technician for help.

For Canadian Models NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modle pour les Canadien REMARQUE: CET APPAREIL NUMRIQUE DE LA CLASSE B EST CONFORME LA NORME NMB-003 DU CANADA. Sur les modles dont la fiche est polarise: ATTENTION: POUR VITER LES CHOCS LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.

For British models Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral Brown: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IMPORTANT The plug is fitted with an appropriate fuse. If the fuse needs to be replaced, the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug. Check for the ASTA mark or the BSI mark on the body of the fuse. If the power cords plug is not suitable for your socket outlets, cut it off and fit a suitable plug. Fit a suitable fuse in the plug.

For European Models

Declaration of Conformity

We, ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY

GROEBENZELL, GERMANY

ONKYO EUROPE ELECTRONICS GmbH K. MIYAGI

declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3.

5 En

Features Plays Audio CD, CD-R, CD-RW, MP3 CD, and WMA

CD*

New circuit technology for Buffer Circuitry Separate Digital/Analog Circuitry Separate Massive Transformers for Digital and Analog

Circuitry (Toroidal Transformer for Analog Circuitry) Thermally Regulated High-Precision Clock Silent Disc Mechanism with Solid Die-Cast Aluminum

Tray Separate Anti-Vibration Aluminum Panels for Top,

Front, and Sides New Circuit Board Construction to Reduce Vibration PLL Ultra Low Jitter Technology Separate TI (Burr-Brown) 192 kHz/24-Bit DACs

(PCM1792) for L/R Channels Pure Analog Mode Transport Mode for Digital Output AES/EBU Balanced Digital Output with XLR

Connector 3 Digital Outputs (Optical, Coaxial and AES/EBU) Gold-Plated, Machined Solid Brass, Wide Pitch Audio

Outputs Display Dimmer (Normal/Dim/Off)

* Discs should be properly finalized.

6 En

Technologies New circuit technology Since the advent of digital audio, signal-to-noise ratios have improved dramatically. However, the S/N ratio reflects static noise only, and takes no account of another type of noise that occurs as the byproduct of sound reproductiondynamic noise. To reduce this type of noise, Onkyo has developed New circuit technology for use in our hi-fi components. Despite being beyond the normal range of human hearing, frequencies above 100 kHz are susceptible to clock pulse and other forms of distortion from digital devices. Such distortion in the super-high-frequency range can generate beat interference, which in turn affects the character or atmosphere of the original sound. By improving linearity and reducing distortion in the super-high-frequency range, Onkyos new New circuit technology effectively reduces perceptible noise. New circuit technology is incorporated into the buffer circuitry of the C-7000R CD player.

Separate Digital/Analog Circuitry and Transformers To prevent unwanted interference, the C-7000R employs physically separate circuitry for digital and analog processing. In the same vein, the player also features separate transformers for digital and analog circuitry.

Thermally Regulated Super-Precision Clock The C-7000R boasts an extremely precise clocking mechanism that controls and coordinates the timing of all digital signal processesrather like how a conductor directs and coordinates the individual instruments of an orchestra. The C-7000R uses a state-of-the-art crystal oscillator that achieves a frequency deviation of 1.5 ppm at room temperature-much lower than with a conventional oscillator. Even in surrounding temperatures of -30C or +80C the frequency remains stable, with only 0.5 ppm of additional frequency deviation.

PLL (Phase Locked Loop) Ultra-Low Jitter Technology Jitter is an unwanted side-effect of the digital-to-analog conversion process caused by fluctuations in the time domain of a digital signal. PLL ultra-low jitter technology reduces jitter by comparing the input and output phases of the digital signal and creating an accurate clock waveform. This enhances the precision of digital signal processing and noticeably improves perceived audio quality.

New Circuit Board Construction Rather than being directly connected to the chassis base, the circuit boards inside the C-7000R are cushioned by internal struts and affixed to the front, side, and rear panels. This method of construction prevents vibrations from the chassis from adversely affecting the circuit boards.

7 En

Block Diagram

8 En

Supplied Accessories Make sure you have the following accessories:

Remote controller (RC-796C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1) Batteries (R03/AAA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (2)

Power cord (1.8 m/5.9 ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1) (Plug type varies from country to country.)

Audio connection cable (0.8 m/2.6 ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1)

* In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operations are the same regardless of color.

Remote controller and two batteries

Power cord

Audio connection cable

Thank you for purchasing an Onkyo Compact Disc Player. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Compact Disc Player. Please retain this manual for future reference.

9 En

Contents Introduction

Important Safety Instructions .................................................................................2 Precautions...............................................................................................................3 Features ....................................................................................................................5 Technologies ............................................................................................................6 Block Diagram ..........................................................................................................7 Supplied Accessories..............................................................................................8 Before Using the Compact Disc Player................................................................10

Installing the Batteries .......................................................................................10 Using the Remote Controller .............................................................................10 Installing the Compact Disc Player ....................................................................10

Getting to Know the Compact Disc Player ..........................................................11 Front Panel ........................................................................................................11 Display ...............................................................................................................12 Rear Panel .........................................................................................................13 Remote Controller..............................................................................................14 Disc Note ...........................................................................................................15

Connections Connections ...........................................................................................................17

Cable and Jacks ................................................................................................17 Connecting the Power Cord...............................................................................18 Connecting a Preamplifier or Integrated Amplifier .............................................19

Turning On & Basic Operations Basic Operations....................................................................................................21

Turning On/Off the Compact Disc Player ..........................................................21 Playing the Disc .................................................................................................22 Selecting Files (MP3/WMA)...............................................................................23 Setting the Display Brightness...........................................................................24

Advanced Operations Advanced Operations ............................................................................................25

Repeat Playback................................................................................................25 Memory Playback (CD)......................................................................................26 Memory Playback (MP3/WMA)..........................................................................27 Random Playback..............................................................................................29 Selecting a Folder (Search Mode) .....................................................................29 Displaying Disc Information ...............................................................................30

Custom Setup Custom Setup.........................................................................................................31

Setup Procedures ..............................................................................................31 Preferences .......................................................................................................31 Setting the Analog/Digital Output.......................................................................32

Others Troubleshooting.....................................................................................................33 Specifications.........................................................................................................35

10 En

Before Using the Compact Disc Player

Note

If the remote controller doesnt work reliably, try replacing the batteries.

Dont mix new and old batteries or different types of batteries. If you intend not to use the remote controller for a long time,

remove the batteries to prevent damage from leakage or corrosion.

Remove expired batteries as soon as possible to prevent damage from leakage or corrosion.

To use the remote controller, point it at the compact disc players remote control sensor, as shown below.

Note

The remote controller may not work reliably if the compact disc player is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing.

If another remote controller of the same type is used in the same room, or the compact disc player is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

Dont put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries.

The remote controller may not work reliably if the compact disc player is installed in a rack behind colored glass doors. Keep this in mind when installing.

The remote controller will not work if theres an obstacle between it and the compact disc players remote control sensor.

Install the compact disc player on a sturdy rack or shelf. Position it so that its weight is evenly dispersed on its four legs. Do not install the compact disc player in a place with vibration or an unstable location.

Installing the Batteries

1 To open the battery compartment, press the small hollow and slide the cover.

2 Insert the two supplied batteries (R03/AAA) in accordance with the polarity diagram inside the battery compartment.

3 Replace the cover and slide it shut.

Using the Remote Controller

Remote control sensor Compact disc player

Approx. 16 ft. (5 m)30 off center (Left/Right)

Installing the Compact Disc Player

10 cm (4")

20 cm (8")

10 cm (4")

10 cm (4")

11 En

Getting to Know the Compact Disc Player

The page numbers in parentheses show where you can find the main explanation for each item.

a ON/STANDBY button ( 21) Use this button to set the compact disc player to On or Standby.

b Standby LED ( 21) Lights when the compact disc player is in Standby mode.

c Remote control sensor ( 10) The sensor receives control signals from the remote controller.

d Display ( 12) See Display.

e Disc tray ( 22) Insert discs into this tray.

f 0 button ( 22) Opens and closes the disc tray.

g 3 button ( 22) Use this button to pause disc playback. When paused, this resumes playback.

h 2 button ( 22) Use this button to stop disc playback.

i 1 button ( 22) Use this button to play the disc.

j OUTPUT MODE button ( 32) Use this button to switch the audio output signal between analog and digital (or both).

k POWER switch ( 21) This is the main power switch. When set to the OFF position (@), the compact disc player is completely shutdown. It must be set to the ON position (^) to set the compact disc player to On or Standby.

l Display Off LED ( 24) Lights when the display is turned off. Before entering standby mode with the ASb function, the Display Off LED flashes 30 seconds before the ASb function starts running.

m 7 button ( 22) Use this button to skip to the beginning of the track being played. Press and hold down to fast reverse.

n 6 button ( 22) Use this button to skip to the beginning of the next track. Press and hold down to fast forward.

Front Panel

i jd eb

l

c gf h

m n

a

k

12 En

For detailed information, see the pages in parentheses.

a 1 indicator ( 22) Lights during playback.

b 3 indicator ( 22) Lights when playback is paused.

c MEMORY indicator ( 26, 27, 28) Lights during memory playback.

d FOLDER indicator ( 23) Lights together with the folder name.

e TRACK indicator ( 22) Lights together with the track number or file name.

f TOTAL indicator ( 21) Lights when the total and remaining time of the track are shown.

g REMAIN indicator ( 30) Lights when the remaining time of the track is shown.

h RANDOM indicator ( 29) Lights during random playback.

i 1 indicator ( 25) Lights during repeat playback. 1 is shown when only the currently playing track is repeated.

j Audio output indicators Indicate the type of audio output ( 32): DIGITAL and/or ANALOG.

k MP3 indicator ( 21) Lights together with the folder name, file number or file name which contains MP3 tracks.

l WMA indicator ( 21) Lights together with the folder name, file number or file name which contains WMA tracks.

m Message area Displays various information.

Display

b c d e g ja

k l m

ihf

13 En

a AUDIO OUTPUT ANALOG L/R jacks Connect the analog audio in jack of an amplifier or similar to this jack, using the supplied audio cable.

b AUDIO OUTPUT DIGITAL AES/EBU jack This balanced AES/EBU output is for connecting a component with a balanced AES/EBU input.

c AUDIO OUTPUT DIGITAL COAXIAL jack This coaxial digital audio output is for connecting components with coaxial digital audio inputs, such as preamplifier.

d AUDIO OUTPUT DIGITAL OPTICAL jack This optical digital audio output is for connecting components with optical digital audio inputs, such as preamplifier.

e AC INLET The supplied power cord is connected here. The other end of the power cord should be connected to a suitable wall outlet.

Rear Panel

cb eda

See Connections for connection information ( 17 to 19).

14 En

Remote Controller

k

l

j

m

n

g

h

i

f

e

b

c

d

a

You can also use the remote controller to control your Onkyo C-7000R. For detailed information, see the pages in parentheses.

a 8 button ( 21) Sets the compact disc player to On or Standby.

b DIMMER button ( 24) Adjusts the display brightness.

c DISPLAY button ( 30) Displays information about the current input source.

d RANDOM button ( 29) Used with the random playback.

e Playback mode buttons ( 22)

3 button Used to pause playback. When paused, this resumes playback.

7 button Used to skip to the beginning of the track being played.

1 button Used to play the disc.

6 button Used to skip to the beginning of the next track.

5 button Used to fast reverse the current song.

2 button Used to stop disc playback.

4 button Used to fast forward the current song.

f !/"/#/$ and ENTER buttons Used to select and adjust settings.

g SEARCH button ( 29) Search for a folder on a disc containing MP3 or WMA tracks.

h SETUP button Used to change settings.

i Number buttons ( 24) Used to select tracks and the like.

j 0 button ( 22) Open and close the disc tray.

k OUTPUT MODE button ( 32) Use this button to switch the audio output signal between analog and digital (or both).

l REPEAT button ( 25) Used with the repeat playback.

m MEMORY button ( 26, 27, 28) Used to begin or end memory playback.

n CLEAR button Used to clear any numbers that have been entered during numeric input. When making a memory setting, the selected track is erased.

15 En

The compact disc player supports the following discs.

Do not use discs designed for purposes other than audio, such as CD-ROMs for PC use. Abnormal noise could damage the speakers or compact disc player.

The compact disc player supports CD-R and CD-RW discs. Note that some discs may not playback because of the CD characteristics, scratches, contamination or the recording state. A CD recorded with an audio CD record will not playback unless it is finalized.

Never use discs which have a special shape (such as hearts or octagons). These types of discs could jam and damage the compact disc player.

Some audio CDs with copy-control function do not comply with official CD standards. These are special discs and cannot be played with this compact disc player.

Hold discs by the edge, or by the center hold and edge. Avoid touching the playback surface (surface with nothing printed on it).

Do not attach paper or stickers, or write on the playback or label surface of the disc. Take care not to scratch or damage the disc.

Do not use discs with residue from cellophane tape, rental discs with labels which are peeling off, or discs with decorative labels. This type of disc could get stuck in the compact disc player, or could damage the compact disc player.

Do not leave a CD-R/CD-RW having a label printed with an inkjet printer in the compact disc player for a long time. The disc could get stuck in the compact disc player, or could damage the compact disc player. Remove the disc from the compact disc player when not being played, and store it in a case. A freshly printed disc will stick easily, and should not be played immediately.

If the disc is dirty, the compact disc player will have a hard time reading signals, and the audio quality may drop. If the disc is dirty, gently wipe off fingerprints and dust with a soft cloth. Lightly wipe from the center outwards. To remove stubborn dust or dirt, wipe the disc with a soft cloth dampened with water, and then dry it with a dry cloth. Do not use cleaning spray for analog records or antistatic agents, etc. Never use volatile chemicals such as benzine or paint thinner as they can impregnate the disc surface.

Moving the compact disc player from a cold room into a warm room, or heating a cold room with a heater may cause waterdrops to form inside the compact disc player. This is called condensation. Not only does this cause malfunction, but it can also damage the compact disc player or any inserted disc. Remove discs from the compact disc player when not in use. If condensation appears, unplug the power cord and leave the compact disc player more than 3 hours at room temperature.

Disc Note

Supported Discs

Audio CD PCM

CD-R Audio CD, MP3, WMA

CD-RW Audio CD, MP3, WMA

CD playback with copy-control function

Handling Discs

Precautions for Rental Discs

Label surface (printed surface)

Playback surface

Precautions for Inkjet Printable Discs

Caring for Discs

About the Condensation

16 En

MP3 and WMA files recorded on a CD-R/CD-RW can be played with this compact disc player. Use discs which have been recorded following the

ISO9660 Level 2 file system. (The supported directory depth is eight levels, the same as ISO9660 Level 1) Discs recorded with the hierarchical file system (HFS) cannot be played.

Always close the disc tray.

Note

A disc recorded with a recorder or personal computer may not play in some cases. (Cause: Discs characteristics, damaged or dirty disc, dirt on players lens, dew condensation, etc.)

A disc recorded on a personal computer may not play because of the application settings or environment. Record the disc with the proper format. (Contact the application maker for details.)

A disc with insufficient storage capacity may not play back properly.

Only MP3 files with the extension .MP3 or . mp3 are supported.

This compact disc player supports files recorded in MPEG 1 Audio Layer 3 (32-320 kbps), with the sampling frequency of 32/44.1/48 kHz.

Variable bitrates (VBR) between 32 kbps and 320 kbps are supported. The time information during VBR playback may not display correctly.

WMA stands for Windows Media Audio, an audio compression technology developed by Microsoft Corporation USA.

Only WMA files with the extension .WMA or .wma are supported.

Encode the WMA file with an application approved by Microsoft Corporation USA. The file may not playback correct if encoded with an unapproved application.

Variable bitrates (VBR) between 32 kbps and 192 kbps (32/44.1/48 kHz) are supported.

Copyright-protected WMA files cannot be played back. WMA Pro, Lossless and Voice are not supported.

* Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or in other countries.

Playback of MP3 and WMA CDs

Playback of MP3 CDs

Playback of WMA CDs

17 En

Connections

Connections

Note

Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

To prevent interference, keep audio cables away from power cords and speaker cables. The compact disc players optical digital jack has a shutter-type cover that opens when an optical plug is inserted and closes when its removed. Push plugs in all the way. To prevent shutter damage, hold the optical plug straight when inserting and removing. The analog audio cable can be used instead of the coaxial cable.

Plugging the AES/EBU cable Match the pins and insert the jack until you hear a click. Make sure that the jack is locked by lightly pulling the connection cable.

Unplugging the AES/EBU cable Pull out the connection cable while holding down the button.

Cable and Jacks

Balanced AES/EBU This is a professional digital audio interface. Balanced AES/EBU cables are used for better noise immunity and longer cable runs. The maximum sampling rate for PCM output is 44.1 kHz/16 bit, 2ch.

Optical digital audio Optical digital connections allow you to enjoy digital sound. The maximum sampling rate for PCM input is 44.1 kHz/16 bit, 2ch.

Coaxial digital audio Coaxial digital connections allow you to enjoy digital sound. The maximum sampling rate for PCM input is 44.1 kHz/16 bit, 2ch.

Analog audio (RCA) Analog audio connections (RCA) carry analog audio.

About Balanced Output (AES/EBU Jack)

OPTICAL

Orange

L

R

White

Red

Right!

Wrong!

1 2Push Push

18 En

Tip

To reduce noise, do not tie the signal cable and power cable together. Wire them so that they are away from each other.

Note

Never disconnect the power cord from the compact disc player while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the compact disc player.

Turning on the compact disc player may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the compact disc player into a different branch circuit.

Do not use a power cord other than the one supplied with the compact disc player. The supplied power cord is designed exclusively for use with the compact disc player and should not be used with any other equipment.

Connecting the Power Cord

AC INLET Compact Disc Player C-7000R

Supplied power cord

To an AC wall outlet (Plug type varies from country to country.)

1 Make sure that the main power of the compact disc player is turned off.

2 Connect all of your components.

3 Connect the supplied power cord to the compact disc players AC INLET.

4 Plug the power cord into an AC wall outlet.

19 En

This is an example of analog connection using the preamplifier P-3000R. This is an example of digital connection using the preamplifier P-3000R. Connect either of them.

Connecting a Preamplifier or Integrated Amplifier

Analog Connection

L

R

Preamplifier P-3000R

Compact Disc Player C-7000R

Digital (Optical or Coaxial) Connection

Preamplifier P-3000R

Compact Disc Player C-7000R

Connect either of them.

20 En

Digital (AES/EBU) Connection

Preamplifier P-3000R

Compact Disc Player C-7000R

This is an example of AES/EBU connection using the preamplifier P-3000R.

21 En

Turning On & Basic Operations

Basic Operations

(Audio CD Display)

(MP3/WMA Display)

Tip

After a certain period of warning up, the temperature of the compact disc players components and internal temperature are stabilized, and the sound will soften.

Note

If the message NO DISC appears on the display, no disc information is available.

The compact disc player remembers the state when power was previously turned OFF, and returns to the state.

Note

See Custom Setup for the auto standby function ( 32).

Turning On/Off the Compact Disc Player

POWER

ON/STANDBY

8

Turning On the Compact Disc Player

1 Set POWER to the ON position (^) on the front panel.

2 Press 8 to turn on the compact disc player. The compact disc player comes on, the display lights, and the Standby LED goes off.

You can also use compact disc players ON/STANDBY.

Total number of tracks

Total playing time

Total number of folders

Total number of tracks

Turning Off the Compact Disc Player

1 Press 8 to set the compact disc player to Standby. The compact disc player will enter Standby mode, and the Standby LED lights.

You can also use compact disc players ON/STANDBY.

2 To completely shut down the compact disc player, set POWER to the OFF position (@).

22 En

(Audio CD Display)

(MP3/WMA Display) File name will be displayed by scrolling.

Tip

Only alphanumeric characters in MP3/WMA CD information are displayed correctly. Double-byte characters and other characters appear as underscores.

If a disc has been set in the tray, when the power of the compact disc player is turned on, then it starts to play automatically.

To Select Tracks Press 6 to select the next track/file or 7 to select the previous track/file.

If you press 7 during playback or while playback is paused, the beginning of the current track/file is selected.

If you select a track/file while playback is stopped, press 1 to start playback.

When 7/6 are pressed, the following Disc information is displayed for MP3/WMA. (During playback) File number/File name File name File number/playing time (Paused) File number/File name File name Folder number/File number

To Fast-Forward or Fast-Reverse During playback or while playback is paused, hold down 4 to fast-forward or 5 to fast-reverse.

To Pause Playback During playback, press 3. The 3 indicator lights.

To resume playback, press 1 or 3 again.

To Stop Playback Press 2 to stop playback.

To Eject the Disc Press 0 to open the disc tray.

Note

For MP3/WMA CDs, you can select MP3/WMA files in other folders.

Playing the Disc

1 Press 0 to open the disc tray.

Pressing 0 while the compact disc player is on Standby will turn on the compact disc player and open the disc tray.

0 3

76

2 1

0

3, 7, 1, 6, 5, 2, 4

2 Place the disc on the tray with the label-side facing up.

When you want to listening to the 8 cm disc, place it in the center of the tray.

3 Press 1 to start playback. The disc tray closes and playback starts.

Track currently playing

Elapsed track time

1 indicator 3 indicator

23 En

For MP3/WMA CDs, files (MP3/WMA files) may be organized in a hierarchically, with folders containing files and subfolders, as shown below.

For the compact disc player, there are two modes for selecting files (MP3/WMA files): Navigation mode and All Folder mode. In Navigation mode, you can select files (MP3/WMA files) by navigating through the folder hierarchy, moving in and out of folders and subfolders. In All Folder mode, all folders appear at the same level, making it easy to select folders regardless of the hierarchy.

Note

If you dont select a specific MP3/WMA file or folder for playback, all of the MP3/WMA files on the disc will be played in numerical order starting with file #1 in parentheses.

Selecting Files (MP3/WMA)

In this manual, MP3/WMA files are referred to as files. Likewise, folders (directories) are referred to as folders.

File #11

File #1

File #10

Folder #3

File #12

Root Folder #1

Folder #2

File #13

Folder #4

File #14

File #18

In Navigation mode, you can select files by navigating through the folder hierarchy. This mode can only be used while playback is stopped.

To cancel the procedure at any point, press 2 on the remote controller.

Note

The behavior of 2 on the compact disc player can be set from STOP KEY ( 32).

Selecting Files in Navigation Mode

1 While playback is stopped, press " or 2. The compact disc player enters Navigation mode and [ROOT] appears on the display.

76

2 1

3, 7, 1, 6, 2

!, ", #, $

ENTER

2 Press " or ENTER (front panel: 1). The first folder name in ROOT appears on the display. If the disc contains no folders, the first file name appears.

3 Use #/$ or 7/6 to select other folders and files at the same level. To move up a level, press ! or 3 (front panel: 2). Folders that dont contain files or subfolders cant be selected.

4 Press ENTER or " to move down a level (front panel: 1).

5 Use #/$ or 7/6 to select a file in the folder.

6 Press ENTER or 1. Playback will start with the specified file or folder and continue until all of the files on the disc have been played.

24 En

In All Folder mode, you dont have to navigate the folder hierarchy because all folders that contain files appear at the same level. This mode can only be used while playback is stopped.

To cancel the procedure at any point, press 2.

To Select Folders and Files by Number 1. Use the number buttons as shown in the examples

below to enter folder/file numbers.

2. Playback starts. When you enter folder number, playback will start from the first file in the selected folder. If a folder contains more than 99 files, single- and double-digit file numbers must be preceded by zeros. For example, to specify file #8, press 8. To specify file #34, press >10, 3, and 4. To specify file #134, press >10, 1, 3, and 4.

Note

The behavior of 2 on the compact disc player can be set from STOP KEY ( 32).

Selecting Files in All Folder Mode

1 While playback is stopped, press ! or 3 (front panel: press and hold 2). The compact disc player enters All Folder mode, and 1- appears on the display.

2 Use #/$ or 7/6 to select the other folders. You can select any folder that contains files.

76

2 1

3, 7, 1, 6, 2

!, ", #, $, ENTER

3 Press " (front panel: 1). The first file name inside the folder appears.

Use #/$or7/6 to select the files within the folder.

To select another folder, press 3 again(front panel: 2), and then use 7/6 to select it.

4 Press ENTER or 1 to start playback.

Playback will start with the specified file or folder and continue until all of the file on the disc have been played.

To select: Press:

Folder/File #8

Used to enter numbers over 10.

Folder/File #10

Folder/File #34

You can adjust the brightness of the compact disc players display.

Note

The display lights for a 5 seconds if you control any buttons on the front panel or remote controller when the display brightness is set to OFF.

Setting the Display Brightness

1 Press DIMMER repeatedly to change the brightness of the display in sequence.

Normal Dim Off

DIMMER

Normal

Dim

Off The Display Off LED lights.

25 En

Advanced Operations

Advanced Operations

In repeat playback, you can play an entire disc repeatedly, play one track repeatedly, or combine it with memory playback to play the playlist repeatedly, or random playback to play all of the tracks on the disc in random order repeatedly.

Tip

Repeat playback is cancelled when you press 0 to open the disc tray.

Repeat playback is cancelled when you press 8 or ON/STANDBY to turn off the compact disc player.

Repeat Playback

REPEAT

1 Press REPEAT repeatedly to select Repeat All, Repeat 1 or Repeat Off.

The or 1 indicator lights.

Repeat All Repeat 1 Repeat Off

Repeat-1 playback cant be combined with memory playback, random playback.

2 To cancel repeat playback, press REPEAT repeatedly until the RPT OFF appears.

The or 1 indicator goes off.

indicatorRepeat All

1 indicatorRepeat 1

Repeat Off

26 En

In memory playback, you can create a playlist of up to 25 tracks. Memory playback can be set only when the playback is stopped.

To Change the Display While the memory setting operations, press DISPLAY repeatedly to change the display information as follows: Track number/Playlist number Track number/Playing time Track number/Total playing time

To Select Other Tracks During Memory Playback

Use 7/6 to select other tracks during memory playback.

To Check the Playlist While playback is stopped, use 5/4 to scroll through the playlist. Track number and play time are displayed.

To Remove Tracks from the Playlist While memory playback is stopped, press CLEAR.

Each press removes the last track from the playlist. The playlist is deleted on changing the playback mode

(press MEMORY after stopping the playback).

To Cancel Memory Playback Stop the playback, then press MEMORY to change the

playback mode. The MEMORY indicator goes off, and memory playback is cancelled.

Memory playback is also cancelled by pressing 0 to open the disc tray, 8 or ON/STANDBY to turn off the compact disc player.

Note

If the total playing time is more than 99 minutes and 59 seconds, --:-- appears.

You can add up to 25 tracks to the playlist. If you try to add more, the message MEM-FULL appears.

Memory Playback (CD)

DISPLAY

7, 1, 6, 5, 4

0

MEMORY

ENTER

CLEAR

1 Press MEMORY. The MEMORY indicator lights.

2 Use 7/6 to select the first track you want to add to the playlist, and then press 1 or ENTER.

Repeat this step to add additional tracks to the playlist. You can alternatively use the number buttons to select tracks.

3 Press ENTER or 1. The memory playback starts.

MEMORY indicator

Playlist numberTrack number

Track currently playing

27 En

In memory playback, you can create a playlist of up to 25 files. Memory playback can be set only when the playback is stopped.

To Change the Display While the memory setting operations, press DISPLAY to change the display information as follows: File name Folder name Folder number/File number

Note

See Selecting Files (MP3/WMA) for the Navigation Mode information ( 23).

The behavior of 2 on the compact disc player can be set from STOP KEY ( 32).

Memory playback is cancelled when you press 0 to open the disc tray.

Memory playback is cancelled when you press 8 or ON/STANDBY to turn off the compact disc player.

Memory Playback (MP3/WMA)

Memory Playback in Navigation Mode

76

2 1

3, 7, 1, 6, 2

MEMORY

DISPLAY

!, ", #, $

ENTER

1 Press MEMORY. The MEMORY indicator lights.

2 Press " or 2. The compact disc player enters Navigation mode and [ROOT] appears on the display.

3 Press " or ENTER (front panel: 1). The first folder name in ROOT appears on the display.

4 Use #/$ or 7/6 to select other folders and files at the same level. Folders that dont contain files or subfolders cant be selected.

5 Press ENTER or " to move down a level (front panel: 1).

6 Use #/$ or 7/6 to select a file in the folder.

7 Press 1. The first file is memorized in the playlist.

8 Use #/$ or 7/6 to continue selecting the memory file.

To move up a level, press ! or 3 (front panel: 2). To continue selecting the memory file, repeat steps 4 to 7. To memorize other files of the same folder in the playlist, use 7/6 to select files, then press 1.

9 Press ENTER or 1. Memory playback starts.

28 En

Note

See Selecting Files (MP3/WMA) for the All Folder Mode information ( 24).

The behavior of 2 on the compact disc player can be set from STOP KEY ( 32).

Memory playback is cancelled when you press 0 to open the disc tray.

Memory playback is cancelled when you press 8 or ON/STANDBY to turn off the compact disc player.

Memory Playback in All Folder Mode

1 Press MEMORY. The MEMORY indicator lights.

2 Press ! or 3 (front panel: press and hold 2). The compact disc player enters All Folder mode and 1- appears on the display.

3 Use #/$ or 7/6 to select the folders.

76

2 1

3, 7, 1, 6, 2

MEMORY

!, ", #, $

ENTER

MEMORY indicator

4 Press " (front panel: 1).

5 Use #/$ or 7/6 to select the files.

6 Press 1 to memorized the first file.

7 Press 3 (front panel: 2), then repeat steps 3 to 6. To memorize other files of the same folder in the playlist, repeat steps 5 to 6.

8 Press ENTER (front panel: 1). Memory playback starts.

29 En

In random playback, all of the files on the disc are played in random order. This mode can only be used while playback is stopped.

If you press RANDOM during playback, the message NOR PLY (Normal play) is displayed.

Tip

Random playback is cancelled when you press 0 to open the disc tray.

Random playback is cancelled when you press 8 or ON/STANDBY to turn off the compact disc player.

Random Playback

1 While playback is stopped, press RANDOM. The RANDOM indicator lights.

2 Press 1. The random playback starts.

3 To cancel random playback, stop the playback, then press RANDOM to change the playback mode. The RANDOM indicator goes off, and random playback is cancelled.

RANDOM

1

RANDOM indicator

This section explains how to select MP3/WMA folders during Playback.

Note

SEARCH cannot be used during Random Playback and Memory Playback ( 26, 29).

See Selecting Files in All Folder Mode to select folder by number( 24).

Selecting a Folder (Search Mode)

1 During playback, press SEARCH. The compact disc player enters All Folder mode and folders are displayed.

2 To select the previous folder, press 7. To select the next folder, press 6. You can also use the number buttons to select the folder.

3 Press ENTER or 1. Playback will start from the first file in the selected folder.

ENTER

SEARCH

7, 6

30 En

(Audio CD Display) Track and total playing time appears on the display.

(MP3/WMA Display) The name of disc appears on the display.

(Audio CD Display)

Elapsed file time: The length of time that the current file has been playing (default display).

Remaining file time: The amount of time remaining for the current file (REMAIN indicator appears).

Remaining disc time: The amount of time remaining for the entire disc (TOTAL and REMAIN indicators appear).

(MP3/WMA Display) You can display various information about the MP3/WMA file currently playing, including ID3 tags such as title name, artist name, and album name.

Elapsed file time: The length of time that the current file has been playing (default display).

File name: Name of the current file.

Folder name: Name of the current folder.

Title name: Title of the current file (if ID3 tag present). When there is no ID3 tag, the message TITLE-NO DATA appears.

Artist name: Name of the Artist (if ID3 tag present).

Album name: Name of the album (if ID3 tag present).

Sampling rate and bit rate: Sampling rate and bit rate of the current file.

Note

To display the disc name, press DISPLAY while playback is stopped.

If a file or folder name contains any characters that cannot be displayed, an underscore will appears in place of those characters. Alternatively, you can set the compact disc player so that names containing such characters are displayed as FILE n or FOLDER n, n being the file or folder number. See BAD- NAME for undisplayable characters setting ( 31).

Displaying Disc Information

1 Press DISPLAY repeatedly to show the following disc information.

While playback is stopped

DISPLAY

Total number of tracks

Total playing time

During playback or pause

REMAIN indicator

31 En

Custom Setup

Custom Setup

To cancel the procedure at any point, press SETUP.

Setup Procedures

1 Press SETUP.

2 Use #/$ or 7/6 to select the preference you want to change.

The preferences are explained in the next column.

3 Press ENTER or 1.

4 Use #/$ or 7/6 to select the preferences options.

5 Press ENTER or 1. When the preference has been set, FINISH appears on the display.

7, 1, 6

SETUP

#, $

ENTER

FILTER SHARP (default)

This preference allows the band property up to 20 kHz to be output almost flat.

SLOW This preference brings higher reproducibility of input waveform, and is suitable to reproduce agogics, or subtle attack of sound signals, along with sound image localization for each musical instrument.

This preference configures the setting to switch the characteristics of the digital filter for D/A conversion. You can opt for whichever of the characteristics that vary depending on your switching.

PHASE NORMAL (default)

The waveform recorded in disc will be output with its polarity left intact.

REVERSE The waveform recorded in disc will be output with its reversed polarity.

This preference configures the setting to switch the phase of the analog audio output. You may give it a try to switch and listen so that an optimum sound quality can be obtained from the amplifier and the speakers on line.

DISC DISPLAY (default) NOT

This preference determines whether or not the disc name is displayed when an MP3/WMA CD is read.

FILE SCROLL (default) NOT

This preference determines whether or not the file name scrolls across the display when an MP3/WMA file is selected. In Navigation mode, the file name scrolls across the display regardless of this setting ( 23).

FOLDER SCROLL (default) NOT

This preference determines whether or not the folder name scrolls across the display when an MP3/WMA folder is selected. In Navigation mode, the folder name scrolls across the display regardless of this setting ( 23).

HIDE-NUM DISABLE (default)

Displays numbers. ENABLE

Hides numbers. This preference determines whether or not the numbers at the beginning of file and folder names are hidden. When you create an MP3/WMA CD on a personal computer, you cannot normally determine the playback order of the files. However, if you number the MP3/WMA files in order, starting with 01, 02, 03, and so on, they will play in that order.

BAD-NAME NOT (default) REPLACE

This preference determines whether or not file and folder names that contain undisplayable characters are replaced with FILE n. or FOLDER n., n being the file or folder number. When set to NOT, displayable characters are displayed and underscores are used in place of any undisplayable characters. For ID3 tags, underscores are used in place of undisplayable characters regardless of this preference.

Preferences

AUDIO

DISPLAY

32 En

ID3-VER1 READ (default) NO READ

This preference determines whether or not version 1.0/1.1 tags are read and displayed. When set to NO READ, version 1.0/1.1 ID3 tags will not be displayed.

ID3-VER2 READ (default) NO READ

This preference determines whether or not version 2.2/2.3/2.4 tags are read and displayed. When set to NO READ, version 2.2/2.3/2.4 ID3 tags will not be displayed.

CD-EXTRA AUDIO (default) MP3

This preference applies to CD Extra discs and determines whether music in the audio session or MP3/WMA files in the data session are played.

JOLIET USE SVD (default) ISO9660

This preference applies to MP3/WMA CDs in Joliet format and determines whether the compact disc player reads the SVD data or treats the disc as an ISO 9660 disc. Normally, this preference doesnt need to be changed. SVD (Supplementary Volume Descriptor) supports long file and folder names and characters other than letters and numbers.

STOP-KEY NAVI (default) FOLDER DISABLE

This preference determines how 2 on the compact disc player works. When the NAVI (Navigation) option is selected, pressing 2 once selects Navigation mode. When the FOLDER (ALL Folder) option is selected, pressing 2 once selects All Folder mode. When the DISABLE option is selected, compact disc player does not enter Navigation or All Folder mode by pressing 2.

Note

This setting has no effect on the remote controller.

ASb (Auto Standby) ON OFF

For compact disc player playback, it is activated when the playback is stopped for 30 minutes; however, it is not activated when the playback is paused continuously. Default setting: ON (European models), OFF (North American models)

Note

Before entering standby mode with the ASb function, the Display Off LED flashes 30 seconds before the ASb function starts running.

INITIAL CANCEL EXECUTE

This preference resets the compact disc player to factory default.

Switch the output between DIGITAL/ANALOG, DIGITAL, ANALOG in order.

EXTRA

ASb (Auto Standby)

INITIAL

Setting the Analog/Digital Output

1 Press OUTPUT MODE repeatedly on the front panel. The selected Audio output indicator lights.

DIGITAL/ANALOG (default): Uses both outputs.

DIGITAL: Uses the digital output only. Turn the analog output off to perform more stable playback.

ANALOG: Uses the analog output only. Turn the digital output off to reduce the effect of digital noise during playback.

OUTPUT MODE

Audio output indicator

33 En

Others

Troubleshooting

Make sure that the power cord is properly plugged into the wall outlet ( 18).

Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.

When the set ASb starts running, the compact disc player will automatically go Standby ( 32).

Power

Cant turn on the Compact Disc Player.

The Compact Disc Player turns off unexpectedly.

Check all connections and correct as necessary ( 17). Make sure that there is no unsupported file formats or

signals. The compact disc player is equipped with a feature to

switch the digital/analog output. Check if the connection between the compact disc player and a connected component is appropriate, and also whether the selection of the selector is correct.

Make sure all audio connecting plugs are pushed in all the way ( 17).

The sound quality can be affected by strong magnetic fields, such as that from a TV. Try moving any such devices away from the compact disc player.

If you have any devices that emit high-intensity radio waves near the compact disc player, such as a cellular phone thats being used to make a call, the compact disc player may output noise.

The compact disc players precision drive mechanism may emit a faint hissing sound while reading discs during playback or when searching for tracks. You may be able to hear this noise in extremely quiet environments.

The compact disc player is not a portable device. Use it in a location thats not subject to shock or vibration.

Audio performance will be at its best about 10 to 30 minutes after the compact disc player has been turned on and had time to warm up.

Using cable ties to bundle audio cables with speaker or power cables may degrade the sound quality. So dont do it.

Audio

Theres no sound.

The sound quality is not good.

Audio output is intermittent when the Compact Disc Player is subjected to vibration.

Audio performance

34 En

The disc is upside down. Load the disc with the label- side facing up ( 15, 22).

The disc is dirty. Remove the disc and clean it ( 15). If condensation appears, unplug the power cord and

leave the compact disc player more than 3 hours at room temperature.

Make sure the disc is standard. See Disc Note ( 15). CD-R/CD-RW that are not finalized cannot be played.

Install the compact disc player somewhere free of vibration.

The disc is dirty. Remove the disc and clean it ( 15). The disc is very scratched. Replace the disc.

No such track on the disc. Enter another number ( 24).

The disc is dirty. Remove the disc and clean it ( 15). The disc is very scratched. Replace the disc.

Turn off any special playback modes (e.g. repeat, memory, or random).

Make sure the audio cable is connected correctly ( 17).

Make sure that all audio connecting plugs are pushed in all the way ( 17).

Make sure that the connected components input jack and the input settings are correct.

Make sure that the connected components volume isnt set to the lowest level, and that the volume isnt muted.

Make sure the batteries have been installed with the correct polarity (+/) ( 10).

Replace both batteries with new ones. (Do not mix different types of batteries or new and old batteries.)

The remote controller is too far away from the compact disc player, or theres an obstacle between them ( 10).

The compact disc players remote control sensor is being subjected to bright light (inverter-type fluorescent light or sunlight).

The compact disc player is located behind the glass doors of a audio rack or cabinet.

Disc Playback

Cant play a disc.

Disc playback skips.

Cant enter track numbers for memory playback.

It takes a long time to locate certain tracks.

Can not play tracks in the discs playback order.

External Components

No sound is heard from a connected component.

Remote Controller

The remote controller doesnt work properly.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the units malfunction. Before you record important data, make sure that the material will be recorded correctly.

The compact disc player contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this should happen, unplug the power cord, wait at least 5 seconds, and then plug it again.

Before disconnecting the power cord from the wall outlet, set the main power switch to OFF.

35 En

Specifications

Specifications and features are subject to change without notice.

C-7000R

Frequency Response 2 Hz - 20 kHz

Signal to Noise Ratio 116 dB

Audio Dynamic Range 100 dB

THD (Total Harmonic Distortion) 0.0015 %

Audio Output/Impedance Optical Coaxial AES/EBU

22.5 dBm 0.5 Vp-p / 75 3.3 Vp-p / 110

Rated RCA Output Level and Impedance 2.0 V (rms) / 330 Digital Outputs Optical: 1

Coaxial: 1

Analog Stereo Outputs L, R

Balance Output AES/EBU (DIGITAL)

Power Supply (North American) AC 120 V, 60 Hz (European) AC 230 V, 50 Hz

Power Consumption (North American) 21 W (European) 18 W

Standby Power Consumption (North American) 0.2 W (European) 0.3 W

Dimensions (W H D) 435 W 99 H 315.2 D mm (17-1/8 W 3-7/8 H 12-7/16 D inches)

Weight 12 kg (26.5 lbs)

Operation Condition Temperature/Humidity 5 C - 35 C/15% - 85%

Playable Discs Audio CD, CD-R, CD-RW, MP3, WMA (CD-R, CD-RW) * Discs that have not been properly finalized may only be

partially playable or not playable at all.

SN 29400529

Y1011-1

(C) Copyright 2010 ONKYO CORPORATION Japan. All rights reserved. * 2 9 4 0 0 5 2 9 *

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163

ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.

Manualsnet FAQs

If you want to find out how the C 7000R Onkyo works, you can view and download the Onkyo C 7000R Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Onkyo C 7000R as well as other Onkyo manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Onkyo C 7000R. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Onkyo C 7000R Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Onkyo C 7000R Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Onkyo C 7000R Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Onkyo C 7000R Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Onkyo C 7000R Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.