Contents

Onkyo A 9050, A 9030 Instruction Manual PDF

1 of 32
1 of 32

Summary of Content for Onkyo A 9050, A 9030 Instruction Manual PDF

Integrated Amplifier

A-9050/ A-9030 Instruction Manual

Thank you for purchasing an Onkyo Integrated Amplifier. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Integrated Amplifier. Please retain this manual for future reference.

Contents

Introduction ...................................2

Connections.................................12

Turning On & Basic Operations....... 21

Advanced Operations .................25

Others...........................................26

E n

2 En

Introduction

Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in

accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen

into the apparatus, C. If the apparatus has been exposed to rain or water, D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in any way, and

F. When the apparatus exhibits a distinct change in performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Dont put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. (Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. When a shelf is located above the unit, the rear edge of the shelf shall be set 10 cm (4") away from the backboard to improve ventilation.)

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING RISK OF ELECTRIC SHOCK

DO NOT OPEN RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

AVIS

PORTABLE CART WARNING

S3125A

3 En

Precautions 1. Recording CopyrightUnless its for personal use

only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC FuseThe AC fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. CareOccasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Dont use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the units rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

For models with [POWER] button, or with both [POWER] and [ON/STANDBY] buttons: Pressing the [POWER] button to select OFF mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

For models with [ON/STANDBY] button only: Pressing the [ON/STANDBY] button to select Standby mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Preventing Hearing Loss Caution Excessive sound pressure from earphones and headphones can cause hearing loss.

6. Batteries and Heat Exposure Warning Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.

7. Never Touch this Unit with Wet HandsNever handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

8. Handling Notes If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case.

This units top and rear panels may get warm after prolonged use. This is normal.

If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models FCC Information for User CAUTION: The user changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and

receiver. Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV

technician for help.

For Canadian Models NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modle pour les Canadien REMARQUE: CET APPAREIL NUMRIQUE DE LA CLASSE B EST CONFORME LA NORME NMB- 003 DU CANADA. Sur les modles dont la fiche est polarise:

ATTENTION: POUR VITER LES CHOCS LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.

4 En

For British models Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral Brown: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IMPORTANT The plug is fitted with an appropriate fuse. If the fuse needs to be replaced, the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug. Check for the ASTA mark or the BSI mark on the body of the fuse. If the power cords plug is not suitable for your socket outlets, cut it off and fit a suitable plug. Fit a suitable fuse in the plug.

For European Models

Supplied Accessories Make sure you have the following accessories:

Remote controller and two batteries

Remote controller (RC-830S) . . . . . . . . . . . . . . . . . . . . (1) Batteries (R03/AAA) . . . . . . . . . . . . . . . . . . . . . . . . . . . (2) (Note for China: The battery for the remote controller is not supplied for this unit.)

Power cord (A-9050 only)

Power cord (5.9 ft/1.8 m). . . . . . . . . . . . . . . . . . . . . . . . (1) (Plug type varies from country to country.)

* In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operations are the same regardless of color.

Declaration of Conformity

We, ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY

GROEBENZELL, GERMANY

ONKYO EUROPE ELECTRONICS GmbH K. MIYAGI

declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3.

5 En

Features A-9050 Integrated Digital Amplifier Three-stage Inverted Darlington Circuitry Digital Inputs (Optical/Coaxial) Wolfson 192 kHz/24 bit DACs withDIDRC Circuitry Inside (WM8718) Phase Matching Bass Technology 1.6 mm Full Flat Chassis 75 W/ch (1 kHz, 8 ohms, 0.08 % THD, 2ch Driven FTC) WRAT (Wide Range Amplifier Technology) DIDRC (Dynamic Intermodulation Distortion Reduction Circuiry) High Current Low Impedance Drive 10,000 F Capacitor 2 Optimum Gain Volume Aluminum Front Panels and Volume Knob Direct Mode Switch

A-9030 Integrated Digital Amplifier Three-stage Inverted Darlington Circuitry Phase Matching Bass Technology 1.6 mm Full Flat Chassis 65 W/ch (1 kHz, 4 ohms, 0.08 % THD, 2ch Driven IEC) WRAT (Wide Range Amplifier Technology) High Current Low Impedance Drive 8,200 F Capacitor 2 Optimum Gain Volume Direct Mode Switch

6 En

Contents

Introduction

Important Safety Instructions..........................................2 Precautions .......................................................................3 Supplied Accessories ......................................................4 Features.............................................................................5 Before Using the Integrated Amplifier ............................7

Installing the Batteries.....................................................7 Using the Remote Controller...........................................7 Installing the Integrated Amplifier....................................7

Getting to Know the Integrated Amplifier.......................8 Front Panel .....................................................................8 Rear Panel ......................................................................9 Remote Controller.........................................................10

Connections

Connections ....................................................................12 Connecting Your Speakers ...........................................12 Cable and Jacks ...........................................................14 Connecting the Power Cord..........................................14 Connecting a CD Player ...............................................15 Connecting a Tuner ......................................................16 Connecting an Onkyo Dock ..........................................17 Connecting Onkyo u Components.............................18 Connecting a Turntable.................................................19 Connecting a Cassette Tape Deck ...............................19 Connecting a Recording Component............................19 Connecting a Subwoofer With

Built-In Power Amplifier ..............................................20 Using the Integrated Amplifier as a Preamplifier...........20

Turning On & Basic Operations

Basic Operations ............................................................21 Turning On/Off the Integrated Amplifier ........................21 Selecting Speakers A and Speakers B .........................22 Adjusting the Volume ....................................................22 Selecting the Input Source............................................23 Using the Direct Function..............................................23 Using the PHASE MACHING BASS Function ..............23 Adjusting the Bass, Treble and Balance .......................24 Muting the Sound..........................................................24 Using Headphones .......................................................24

Advanced Operations

Custom Setup .................................................................25 Setting the Auto Standby Function ...............................25 Setting the speaker impedance ....................................25

Others

Troubleshooting .............................................................26 Specifications .................................................................28

7 En

Before Using the Integrated Amplifier

Note

If the remote controller doesnt work reliably, try replacing the batteries.

Dont mix new and old batteries or different types of batteries. If you intend not to use the remote controller for a long time,

remove the batteries to prevent damage from leakage or corrosion.

Remove expired batteries as soon as possible to prevent damage from leakage or corrosion.

To use the remote controller, point it at the integrated amplifiers remote control sensor, as shown below.

Note

The remote controller may not work reliably if the integrated amplifier is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing.

If another remote controller of the same type is used in the same room, or the integrated amplifier is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

Dont put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries.

The remote controller may not work reliably if the integrated amplifier is installed in a rack behind colored glass doors. Keep this in mind when installing.

The remote controller will not work if theres an obstacle between it and the integrated amplifiers remote control sensor.

Install the integrated amplifier on a sturdy rack or shelf. Position it so that its weight is evenly dispersed on its four legs. Do not install the integrated amplifier in a place with vibration or an unstable location. The integrated amplifier is designed to have high conversion efficiency, however, its temperature will become much higher than other audio equipment. Therefore, make sure not to hamper heat dissipation by ensuring proper ventilation.

Installing the Batteries

1 To open the battery compartment, press the small hollow and slide the cover.

2 Insert the two supplied batteries (R03/AAA) in accordance with the polarity diagram inside the battery compartment.

3 Replace the cover and slide it shut.

Using the Remote Controller

Installing the Integrated Amplifier

Remote control sensor

Integrated amplifier

Approx. 16 ft. (5 m)

Approx. 8 in. (20 cm)

Ensure proper ventilation.

Approx. 8 in. (20 cm)

Approx. 8 in. (20 cm)

Approx. 4 in. (10 cm)

8 En

Getting to Know the Integrated Amplifier

For detailed information, see the pages in parentheses.

a 8ON/STANDBY button ( page 21) Sets the integrated amplifier to On or Standby.

b Remote control sensor ( page 7) Receives control signals from the remote controller.

c Volume controller ( page 22) Adjusts the volume.

d Input source LEDs ( page 23) Lights according to the selected input source. (*A-9050 only)

e INPUT selector ( page 23) Selects the input sources in sequence.

f SPEAKERS button ( page 22) Selects Speakers A, Speakers B, or both.

g A/B LEDs ( page 22) Lights according to the selected speaker output.

h BASS /+ controller ( page 24) Adjusts the level of bass sounds.

i TREBLE /+ controller ( page 24) Adjusts the level of treble sounds.

j BALANCE L/R controller ( page 24) Adjusts the balance of left and right channels.

k DIRECT LED ( page 23) Lights when the integrated amplifier is in Direct mode.

l DIRECT button ( page 23) Enables or disables the Direct function.

m PHASE MATCHING BASS LED ( page 23) Lights when the integrated amplifier is in Phase matching bass mode.

n PHASE MATCHING BASS button ( page 23) Enables or disables the Phase matching bass function.

o LINE5 (AUX) jack Connect playback devices with analog audio output.

p PHONES jack ( page 24) Connects headphones with a standard plug.

Front Panel

a 3 4 5

87

2

6 j k ml on p9

9 En

a GND screw Connects the turntables ground wire.

b u MODE selector (A-9050 only)

c DIGITAL IN OPTICAL D3 jack (A-9050 only) Connects components such as CD players with optical digital audio output.

d DIGITAL IN COAXIAL D1/D2 jacks (A-9050 only) Connect components such as CD players with coaxial digital audio output.

e PHONO (MM) L/R jacks Connect a turntable with analog audio output.

f LINE IN 1/2/3/4 L/R jacks Connect playback devices with analog audio output.

g LINE OUT L/R jacks Connect components such as analog line-level sources. The input signals are output with no level adjustment.

h PRE OUT L/R jacks (A-9050 only) Connect a power amplifier when the integrated amplifier is used as a preamplifier (Pre mode).

i PREOUT SUBWOOFER jack

j u REMOTE CONTROL jack Connect Onkyo components such as Onkyo Docks, CD Players, or Tuner with u (Remote Interactive) jacks.

k SPEAKERS A terminals Connect Speakers A.

l SPEAKERS B terminals Connect Speakers B.

m AUTO STANDBY selector Enables or disables the Auto standby function.

n SPEAKER IMPEDANCE selector (A-9050 only) Switches the speaker impedance to 4 or 8 .

o AC INLET (A-9050 only) Connects the supplied power cord. The other end of the power cord should be connected to a suitable wall outlet.

p POWER CORD (A-9030 only)

Rear Panel

3 4

5

2

876 j o pk ml n9

a

See Connections for connection information ( page 12).

10 En

For detailed information, see the pages in parentheses.

a 8 button ( page 21) Sets the integrated amplifier to On or Standby.

b DIMMER button Adjusts the display brightness.

c !/"/#/$ and ENTER buttons Select and adjust settings.

d VOLUME q/w buttons ( page 22) Adjust the volume of the integrated amplifier.

e INPUT!/" buttons ( page 23) Select an input source.

f RETURN button Returns to the previous display when changing settings.

g MUTING button ( page 24) Mutes or unmutes the integrated amplifier.

You can also use the remote controller to control your Onkyo CD Player, Onkyo u Dock, or Onkyo Tuner.

Note

With some components, the remote controller may not work, or only partially.

To control the Onkyo Dock and Onkyo Tuner, an u connection is required ( page 18).

Refer to the manuals supplied with your Onkyo CD Players, Tuner or u Docks.

Controlling the Onkyo CD player

d 8 CD button

f Playback mode buttons

Note

Make sure the remote controller is pointed at the CD player when using it.

Controlling the Onkyo Dock

a 8 button

b DIMMER button

c !/" and ENTER buttons

g Dock control buttons

Controlling the Onkyo Tuner / Network Tuner

a 8 button

b DIMMER button

c !/"/#/$ and ENTER buttons

e DISPLAY button

g Network Tuner control buttons

h INPUT SELECTOR or BAND buttons

Remote Controller

* g

e

d

*

d

f

e

f

h

g

cc

bb

aa

* Not used with the integrated amplifier

11 En

*: A-9050 only

Connecting Terminal LINE1/D1* LINE2/D2* LINE3/D3*

Component Button on Remote Controller

CD Player TUNER u DOCK

1 8 8 8

2 DIMMER DIMMER DIMMER

3

!/" !/" (Tuning Up/Down)

!/"

#/$ #/$ (Preset Up/Down)

ENTER ENTER ENTER

4 8 CD 8

5 DISPLAY Display the current input and settings.

6

RANDOM RANDOM

REPEAT REPEAT

7 7

5 5

1 1

3 3

4 4

6 6

2 2

7

SHUFFLE SHUFFLE SHUFFLE

MENU MENU MENU

REPEAT REPEAT REPEAT

7 7 7

1/3 1/3 1/3

6 6 6

8 INPUT INPUT SELECTOR /

BAND

12 En

Connections

Connections

Screw-type speaker terminals Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

Banana Plugs (North American models) If you are using banana plugs, tighten the speaker terminal before inserting the banana plug. Do not insert the speaker code directly into the center hole of the speaker terminal.

Connecting Your Speakers

Speakers A

Speakers B

Right Left

Right Left

Integrated Amplifier

1/2" to 5/8" (12 to 15 mm)

13 En

Note

Make sure that the wires do not touch metal parts on the back panel or elsewhere.

Y plugs cannot be connected. Two sets of speakers (Speakers A and Speakers B) can be

connected to the integrated amplifier. You can select which speakers to output audio to when listening to music. You can also output audio from both sets of speakers.

If you use Speakers A or Speakers B, make sure to use speakers with an impedance of 4 to 16 ohms. If you use Speakers A and Speakers B, make sure to use speakers with an impedance of 8 to 16 ohms. Connecting speakers with an impedance less than 8 ohms may cause the protection circuit to activate.

When using only one speaker, or when playing back monaural audio, dont connect a single speaker to both the left and right speaker terminals.

Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+) terminals, and negative () terminals only to negative () terminals. If you get them the wrong way around, the sound will be out of phase and will feel unnatural.

Be careful not to short the positive and negative wires. Doing so may damage the integrated amplifier.

Make sure the metal core of the wire does not have contact with the integrated amplifiers rear panel. Doing so may damage the integrated amplifier.

Dont connect more than one speaker wire to a single speaker terminal. Doing so could damage the integrated amplifier or cause it to malfunction.

Bi-wiring Connection

Bi-wiring provides improved bass and treble performance. Using terminals of both SPEAKERS A and SPEAKERS B, it separates high frequency from low frequency signals.

Tip

As shown on the illustration, the wiring terminals of SPEAKERS A are connected to the tweeter and SPEAKERS B are connected to the woofer. However, wiring them the other way around is also possible.

Important: Bi-wiring can be used only with speakers that support bi-

wiring and that have an impedance of 4-16 ohms. When making the bi-wiring connections, be sure to remove

the jumper bars that link the speakers tweeter (high) and woofer (low) terminals.

When making the bi-wiring connections, set SPEAKERS to A+B ( page 22).

Right speaker

Left speaker

Tweeter (high)

Woofer (low)

Integrated Amplifier

14 En

Note

Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

To prevent interference, keep audio cables away from power cords and speaker cables. The integrated amplifiers optical digital jack have shutter-type covers that open when an

optical plug is inserted and close when its removed. Push plugs in all the way. To prevent shutter damage, hold the optical plug straight when inserting and removing. Do not use digital audio signals other than PCM. * An analog audio cable can be used instead of a coaxial cable. However, we recommend that

you use a coaxial or a composite video cable.

Tip

To reduce noise, do not tie signal cables together with the power cable. Wire them so that they are away from each other.

Depending on the country, the integrated amplifier may be polarity-sensitive. In this case, plug the power cord in a way that provides the best sound quality.

Note

Never disconnect the power cord from the integrated amplifier while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the integrated amplifier.

Turning on the integrated amplifier may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the integrated amplifier into a different branch circuit.

Do not use a power cord other than the one supplied with the integrated amplifier. The supplied power cord is designed exclusively for use with the integrated amplifier and should not be used with any other equipment.

Cable and Jacks

Optical digital audio (A-9050 only)

Optical digital connections allow you to enjoy digital sound such as PCM. The maximum sampling rate for PCM input is 96 kHz/24 bit, 2ch.

Coaxial digital audio* (A-9050 only)

Coaxial digital connections allow you to enjoy digital sound such as PCM. The maximum sampling rate for PCM input is 96 kHz/24 bit, 2ch. The integrated amplifier provides 75-ohm impedance matching.

Analog audio (RCA) Analog audio connections (RCA) carry analog audio.

u To use u (Remote Interactive), you need to connect your Onkyo CD Player, Tuner, or u Dock to the integrated amplifier with an u cable.

Connecting the Power Cord

OPTICAL

Orange

L

R

White

Red

Right!

Wrong!

1 Connect all of your speakers and components.

2 Connect the supplied power cord to the integrated amplifiers AC INLET. (A-9050 only)

3 Plug the power cord into an AC wall outlet.

AC INLET

To an AC wall outlet (Plug type varies from country to country.)

Supplied power cord

A-9030

A-9050

15 En

This is an example of connection using the CD Player.

Digital Connection (A-9050 only)

Tip

The CD player can be connected to the COAXIAL D1 or D2 jack or the OPTICAL D3 jack. However, when using the u interlock function, be sure to connect the CD player to the COAXIAL D1 jack.

Analog Connection

Tip

The CD player can be connected to the LINE IN 1/2/3/4 jack. However, when using the u interlock function, be sure to connect the CD player to the LINE IN 1 jack.

Connecting a CD Player

1 Connect the coaxial digital cable to the COAXIAL D1 jack.

2 Set the RI MODE switch to CD D1.

Integrated Amplifier

CD Player

1 Connect an audio pin cable to the LINE IN 1 jack.

2 Set the RI MODE switch to CD LINE 1. (A-9050 only)

Integrated Amplifier

CD Player

16 En

This is an example of connection using the Tuner.

Digital Connection (A-9050 only)

Tip

The Tuner can be connected to the COAXIAL D1 or D2 jack or the OPTICAL D3 jack. However, when using the u interlock function, be sure to connect the Tuner to the COAXIAL D2 jack.

Analog Connection

Tip

A Tuner can be connected to the LINE IN 1/2/3/4 jack. However, when using the u interlock function, be sure to connect the Tuner to the LINE IN 2 jack.

Connecting a Tuner

1 Connect coaxial digital cable to the COAXIAL D2 jack.

2 Set the RI MODE switch to TUNER D2.

Integrated Amplifier

Tuner

1 Connect an audio pin cable to the LINE IN 2 jack.

2 Set the RI MODE switch to TUNER LINE 2. (A-9050 only)

Integrated Amplifier

Tuner

17 En

This is an example of connection using the Onkyo u Dock.

Digital Connection (A-9050 only)

Tip

An Onkyo Dock can be connected to the COAXIAL D1 or D2 jack or the OPTICAL D3 jack. However, when using the u interlock function, be sure to connect the Onkyo Dock to the OPTICAL D3 jack.

Analog Connection

Tip

An Onkyo Dock can be connected to the LINE IN 1/2/3/4 jack. However, when using the u interlock function, be sure to connect the Onkyo Dock to the LINE IN 3 jack.

Connecting an Onkyo Dock

1 Connect the optical digital cable to the OPTICAL D3 jack.

2 Set the RI MODE switch to DOCK D3.

OPTICAL

Integrated Amplifier

Digital Media Transport, u Dock 1 Connect the audio pin cable to the LINE IN 3 jack.

2 Set the RI MODE switch to DOCK LINE 3. (A-9050 only)

R AUDIO OUT

---- L

Integrated Amplifier

Digital Media Transport, u Dock

18 En

With u (Remote Interactive), you can use the following special functions:

Auto Power On When you start playback on a component connected via u while the integrated amplifier is on Standby, the integrated amplifier will automatically turn on and select that component as the input source.

Direct Change When playback is started on a component connected via u, the integrated amplifier automatically selects that component as the input source.

System Off When you turn off the integrated amplifier, the components turn off automatically.

Remote Control You can use the integrated amplifiers remote controller to control your other u-capable Onkyo Components, pointing the remote controller at the integrated amplifiers remote control sensor instead of the component. To operate the CD player, point the remote controller at the CD player.

Tip

For details on operating the connected components, see Remote Controller ( page 11).

Note

Use only u cables for u connections. u cables are supplied with your Onkyo CD Player, Tuner or u Dock.

If two u jacks are present, you can use either one indifferently as they work the same way.

Connect only an Onkyo CD Player, Tuner or u Dock to the u jack. Connecting other manufacturers components may cause a malfunction.

Only Onkyo CD Players, Tuners, and u Docks are supported by the integrated amplifiers u. With other components such as MD recorders, the u wont work properly.

Some components may not support all u functions. Refer to the manuals supplied with your Onkyo CD Players, Tuner or u Docks.

The CD Players only support the Auto Power On and Direct Change functions.

Connecting Onkyo u Components

1 Make sure that each Onkyo CD Player, Tuner or u Dock is connected and that the RI MODE switch is set correctly ( pages 15 to 17).

Caution

Settings will not be enabled even when the selector is changed in the Standby mode.

To change a setting, be sure to turn on the unit prior to making any changes.

2 Make the u connections (see the illustration).

Digital Media Transport, u DockTuner or CD Player

Integrated Amplifier

19 En

The PHONO input jacks are for use with moving-magnet (MM) type cartridges. Use an analog audio cable to connect the PHONO L/R jacks to the audio output jacks on the turntable, as shown.

Tip

If the turntable has a ground wire, connect it to GND terminal. With some turntables, connecting the ground wire may cause hum, in which case it should be disconnected.

If the turntable has a moving-coil (MC) type cartridge, youll need a commercially available MC phono preamp. In this case, connect the turntable to the phono preamps input, and connect the phono preamps output to the PHONO L/R jacks.

Tip

Connect your cassette tape deck to either of the following jacks: LINE IN 1/2/3/4.

Note

Volume adjustments and use of the muting function are not reflected in the signal output from LINE OUT.

Manual tone adjustments using the BASS /+ controller, TREBLE /+ controller, BALANCE L/R controller, direct function, and phase matching bass function are not reflected in the signal output from LINE OUT.

See the manual of the recording component for instructions on correct use.

Connecting a Turntable

Connecting a Cassette Tape Deck

L

R

AUDIO OUTPUT

Ground wire

Integrated Amplifier

AUDIO OUT

L R

Integrated Amplifier

Cassette tape deck

Connecting a Recording Component

Important: Unless you have the full consent of the copyright holder,

copyright laws prohibit using your recordings for anything other than personal enjoyment!

Do not change the integrated amplifiers input while recording. Doing so will cause the audio from the selected component to be recorded.

AUDIO IN

L R

Integrated Amplifier

Cassette tape deck

20 En

A subwoofer with a built-in power amplifier can be connected to be used. Connect LINE INPUT on the subwoofer with a built-in power amplifier to PRE OUT: SUBWOOFER terminal on the integrated amplifier. If your subwoofer does not have a built-in amplifier, connect the input jack of your amplifier to the pre out jack of the subwoofer. For details, refer to the manual supplied with your subwoofer.

The integrated amplifier can be used as a preamplifier (Pre mode). This is an example of connection using the power amplifier. (A-9050 only)

Connecting a Subwoofer With Built-In Power Amplifier

Integrated Amplifier

Subwoofer with built-in power

amplifier

Using the Integrated Amplifier as a Preamplifier

Integrated Amplifier

Power Amplifier

21 En

Turning On & Basic Operations

Basic Operations

Turning On the Integrated Amplifier

Operating with the remote controller

Operating on the integrated amplifier

Tip

After a certain time of warming up, the internal temperature of the integrated amplifier stabilizes, and the sound is softened.

The integrated amplifier remembers the state when power was last turned off, and returns to that state.

Turning Off the Integrated Amplifier

Operating with the remote controller

Operating on the integrated amplifier

Tip

For details on power management settings, see Setting the Auto Standby Function ( page 25).

Turning On/Off the Integrated Amplifier

1 Press 8. The SPEAKERS (A/B) and Input source LEDs blink, then light up after a short time.

1 Press 8ON/STANDBY. The SPEAKERS (A/B) and Input source LEDs blink, then light up after a short time.

8ON/STANDBY button

1 Press 8. The integrated amplifier enters Standby mode and the LED goes off.

1 Press 8ON/STANDBY. The integrated amplifier enters Standby mode and the LED goes off.

8

22 En

You can select to output sound from Speakers A, Speakers B, or both A + B.

Note

While headphones are connected, this setting is disabled. When this setting is set to A + B, the impedance of speakers is

restricted. For further details, see Connecting Your Speakers ( page 12).

Operating with the remote controller

Operating on the integrated amplifier

Tip

The default level is 0.

Selecting Speakers A and Speakers B

1 Press SPEAKERS repeatedly on the integrated amplifier. The LED of the selected speakers lights.

SPEAKERS button

A LED B LED

Adjusting the Volume

1 Press VOLUME q/w repeatedly.

1 Use the volume controller.

VOLUME q/w

Volume controller

23 En

You can switch inputs to select the desired source component. Choose an input from the following: LINE1, LINE2, LINE3, LINE4, LINE5, PHONO (D1, D2, D3 (A-9050 only)) The LED corresponding to the selected input will light up.

Tip

The LED will blink when D1, D2 or D3 is selected and a signal is not input. (A-9050 only)

Operating with the remote controller

Operating on the integrated amplifier

By bypassing the tone control circuit, the Direct function uses the shortest path for enhanced sound quality. Also, since the left/right balance setting uses a system that doesnt affect the sound quality, the balance can be adjusted even if the Direct function is enabled.

From the warm low notes produced by a cello to the deep frequencies of electronic music, a good compact audio system should be able to deliver plenty of bass resonance. While traditional enhancement systems effectively boost low-frequency sound, they are often prone to the effects of phase shifting, which can overwhelm mid-range frequencies and muddy the sound. Our Phase-Matching Bass Boost technology effectively preserves mid-range clarity-allowing vocals and strings to shine-while maintaining a smooth, powerful bass response at all volume levels.

When the DIRECT function is on, turn the function off to use the PHASE MATCHING BASS effect.

Selecting the Input Source

1 Press INPUT!/" repeatedly.

1 Use the INPUT selector.

INPUT !/"

INPUT selector

Using the Direct Function

1 Press the DIRECT button. The DIRECT LED lights.

Using the PHASE MATCHING BASS Function

1 Press the PHASE MATCHING BASS button. The PHASE MATCHING BASS LED lights up.

DIRECT LED DIRECT button

PHASE MATCHING BASS LED

PHASE MATCHING BASS button

24 En

You can adjust the bass, treble and left/right output balance respectively.

Operating on the integrated amplifier

Tip

By default, bass, treble and balance is set to the center position.

Note

While the Direct function is enabled, bass and treble are disabled.

You can temporarily mute the output of the integrated amplifier.

Note

While the integrated amplifier is muted: Adjusting the volume or setting the integrated amplifier to

Standby will unmute the integrated amplifier.

Note

Always turn down the volume before connecting your headphones.

When headphones are connected, the SPEAKERS button cannot be used.

Adjusting the Bass, Treble and Balance

1 Turn the BASS /+, TREBLE /+ and BALANCE L/R knobs.

BASS /+ TREBLE /+ BALANCE L/R

Muting the Sound

1 Press MUTING. The SPEAKERS (A/B) and SELECTOR LEDs blink. To unmute the integrated amplifier, press MUTING again.

Using Headphones

1 Connect a pair of stereo headphones with a standard plug (1/4 inch or 6.3 mm) to the PHONES jack. When connecting the headphones, the SPEAKERS (A/B) LEDs go off. You can adjust the volume and mute the sound, by using VOLUME q/w. While headphones are connected, no sound is output from the speakers and PRE OUT jacks.

MUTING

PHONES jack

25 En

Advanced Operations

Custom Setup

When the Auto Standby (ASb) function is activated, the integrated amplifier will automatically enter Standby mode if there is no operation for 30 minutes with no audio signal input.

You can set the impedance of the speakers that you connect to the unit. (A-9050 only)

Caution

Settings will not be enabled even when the selector is changed in the Standby mode. To change a setting, be sure to turn on the unit prior to making any changes.

Setting the Auto Standby Function

1 Switch the AUTO STANDBY selector on the units rear panel.

[ON] Enables auto standby.

[OFF] Disables auto standby.

AUTO STANDBY selector

Setting the speaker impedance

1 Switch the SPEAKER IMPEDANCE selector on the units rear panel.

[4 or more and less than 8 ] Sets the impedance to 4 .

[8 or more and 16 or less] Sets the impedance to 8 .

SPEAKER IMPEDANCE selector

26 En

Others

Troubleshooting First check the followings. Since the issue may be caused by other components that are connected, be sure to also check them while referring to their manuals. Further product operating procedures and FAQs (frequently asked questions) are available from the Onkyo web site. http://www.jp.onkyo.com/support/

Cant turn on the Integrated Amplifier.

Make sure that the power cord is properly plugged into the wall outlet ( page 14).

Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.

The Integrated Amplifier turns off unexpectedly.

When the protection circuit is activated (because of speaker short-circuit, overload, or over-current), the integrated amplifier enters Standby mode. Remove the source of the problem and turn the integrated amplifier back on.

Check that the switch on the back of the integrated amplifier is set to the correct setting ( page 25).

The settings are not enabled when the switch is changed during the Standby mode. To change a setting, be sure to turn on the unit prior to making any changes.

Theres no sound.

Make sure the integrated amplifiers volume control is not set to minimum ( page 22).

Make sure the correct input source is selected ( page 23).

Make sure the integrated amplifier is not muted ( page 24).

Make sure the speakers are connected correctly ( page 12). Check all connections and correct as necessary ( page 12). While headphones are connected, the speakers output no

sound ( page 24). The integrated amplifier does not support digital formats

other than PCM. Inputting a digital format other than PCM will cause loud noise.

The sound quality is not good.

Make sure the speaker cables are connected with the correct polarity ( page 12).

Make sure all audio connecting plugs are pushed in all the way ( page 14).

The sound quality can be affected by strong magnetic fields, such as those from a TV. Try moving any such devices away from the integrated amplifier.

If you have any devices that emit high-intensity radio waves near the integrated amplifier, such as a cellular phone thats being used to make a call, the integrated amplifier may output noise.

Headphone output is intermittent or theres no sound.

This may be due to dirty contacts. Clean the headphones plug. See your headphones instruction manual for cleaning information. Also, make sure that the headphones cable is not broken or damaged.

Audio performance

Audio performance will be at its best about 10 to 30 minutes after the integrated amplifier has been turned on and had time to warm up.

Using cable ties to bundle audio cables with speaker or power cables may degrade the sound quality, so refrain from doing it.

Depending on the country, the integrated amplifier may be polarity-sensitive. In this case, plug the power cord in a way that provides the best sound quality.

Install the integrated amplifier on a sturdy rack or shelf. Position it so that its weight is evenly dispersed on its four legs. Do not install the integrated amplifier in a place with vibration or an unstable location.

Plug the power cord into an AC wall outlet.

Tip

Before requesting repairs If the integrated amplifier is no longer working or functioning, any issues may be resolved by resetting the microcomputer contained in the integrated amplifier to revert all settings to their defaults. Before requesting repairs, follow the procedure below to reset the microcomputer. With the integrated amplifier turned on, hold down DIRECT and press 8ON/STANDBY.

Power

Audio

27 En

Theres no sound.

Make sure that the Onkyo Dock is connected to the integrated amplifier properly.

Make sure that no video content is being played. Reset the iPod.

Other

When the Auto Standby (ASb) function is activated, the power of the Onkyo Dock connected via u is automatically turned off ( page 25).

Cant control properly by using the remote controller.

Make sure that the u cable is connected to the integrated amplifier correctly. Check that each device is connected correctly and that the RI MODE switch is set correctly ( page 17).

No sound is heard from a connected component.

Make sure the correct input source is selected ( page 23).

Make sure the analog audio cable is connected correctly ( page 14).

When the u interlock does not function properly

Check that each device is connected correctly and that the RI MODE switch is set correctly ( pages 15 to 17).

Check that the switch on the back of the integrated amplifier is set to the correct setting.

The settings are not enabled when the switch is changed during the Standby mode. To change a setting, be sure to turn on the unit prior to making any changes.

The connecting method may vary depending on the device that will be connected. Please refer to the u connection section in the owners manual of the connected device.

The sound from turntable is distorted.

If your turntable has a built-in phono preamp, connect to other analog inputs such as LINE IN.

If your turntable does not have a built-in phono preamp, connect a turntable to PHONO ( page 19).

Make sure that the ground wire is connected. Otherwise, it may produce an audible hum and noise.

The remote controller doesnt work properly.

Make sure the batteries have been installed with the correct polarity (+/) ( page 7).

Replace both batteries with new ones. (Do not mix different types of batteries or new and old batteries.)

The remote controller is too far away from the integrated amplifier, or theres an obstacle between them ( page 7).

The integrated amplifiers remote control sensor is being subjected to bright light (inverter-type fluorescent light or sunlight).

The integrated amplifier is located behind the glass doors of an audio rack or cabinet.

Onkyo Dock

External Components

Remote Controller

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the units malfunction. Before you record important data, make sure that the material will be recorded correctly.

The integrated amplifier contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this should happen, unplug the power cord, wait at least 5 seconds, and then plug it again.

Before disconnecting the power cord from the wall outlet, set the integrated amplifier to Standby.

If during idling the cover is too hot to touch, then ventilation needs to be improved.

28 En

Specifications

Audio Inputs

Audio Outputs

Others

Specifications and features are subject to change without notice.

A-9050 A-9030 Rated Output Power (North American)

(FTC) 75 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.08 % (FTC) 65 watts minimum continuous power per channel, 4 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.08 % (European) (IEC) 2 ch 75 W at 8 ohms, 1 kHz, 2 ch Driven of 0.08 %

(IEC) 2 ch 65 W at 8 ohms, 1 kHz, 2 ch Driven of 0.08 %

Maximum Effective Output Power

(Asian) (JEITA) 2 ch 80 W at 4 ohms, 1 kHz, 2 ch driven

THD+N (Total Harmonic Distortion+N) 0.08 % (Rated Output Power) 0.08 % (Rated Output Power)

Damping Factor 60 (Front, 1 kHz, 8 ) 60 (Front, 1 kHz, 8 )

Input Sensitivity and Impedance (Unbalance) 175 mV/33 k (LINE) 4.8 mV/47 k (PHONO MM)

175 mV/33 k (LINE) 4.8 mV/47 k (PHONO MM)

Rated RCA Output Level and Impedance 0.175 V/2.2 k (REC OUT) 0.175 V/2.2 k (REC OUT)

Phono Overload 100 mV (MM 1 kHz 0.5 %) 100 mV (MM 1 kHz 0.5 %)

Frequency Response 10 Hz - 100 kHz/+1 dB, 3 dB (LINE1) 10 Hz - 100 kHz/+1 dB, 3 dB (LINE1)

Tone Control Characteristies +14 dB, 14 dB, 100 Hz (BASS) +14 dB, 14 dB, 10 kHz (TREBLE) +0 dB, 14 dB (BALANCE) +8 dB, 80 Hz (PM.BASS)

+14 dB, 14 dB, 100 Hz (BASS) +14 dB, 14 dB, 10 kHz (TREBLE) +0 dB, 14 dB (BALANCE) +8 dB, 80 Hz (PM.BASS)

Signal to Noise Ratio 110 dB (LINE, IHF-A) 80 dB (PHONO MM, IHF-A)

105 dB (LINE, IHF-A) 80 dB (PHONO MM, IHF-A)

Speaker Impedance 4 16 4 16 Power Supply (North American) AC 120 V, 60 Hz

(European) AC 230 V, 50 Hz (European) AC 230 V, 50 Hz (Asian) AC 220 V, 50 Hz

Power Consumption 160 W (European) 135 W (Asian) 125 W

No-sound Power Consumption (North American) 45 W (European) 50 W

35 W

Stand-by Power Consumption (North American) 0.2 W (European) 0.3 W

0.3 W

Dimensions (W H D) 435 mm 139 mm 330.3 mm 17-1/8" 5-1/2" 13"

435 mm 139 mm 330.3 mm 17-1/8" 5-1/2" 13"

Weight 8.2 kg (18.1 lbs) 7.4 kg (16.3 lbs)

Digital Inputs 1 (Rear Optical) 2 (Rear Coaxial)

Analog Stereo Inputs LINE1, LINE2, LINE3, LINE4, LINE5, PHONO LINE1, LINE2, LINE3, LINE4, LINE5, PHONO

Analog Stereo Outputs LINE OUT, PRE OUT LINE OUT

Subwoofer Pre Outputs 1 1

Speaker Outputs SP-A, B SP-A, B

Phones 1 (6.3 ) 1 (6.3 )

u 1 1

29 En

MEMO

30 En

MEMO

31 En

MEMO

SN 29401270B (C) Copyright 2013 Onkyo Corporation Japan. All rights reserved.

C1306-3

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN http://www.onkyo.com/

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. For Dealer, Service, Order and all other Business Inquiries: Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

For Product Support Team Only: 1-800-229-1687 http://www.us.onkyo.com/

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.eu.onkyo.com/

Meridien House, Ground floor, 69 - 71 Clarendon Road, Watford, Hertfordshire, WD17 1DS, United Kingdom Tel: +44 (0)8712-00-19-96 Fax: +44 (0)8712-00-19-95

Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.hk.onkyo.com/

1301, 555 Tower, No.555 West NanJing Road, Jingan District, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 http://www.cn.onkyo.com/

The Americas

China

Europe

Asia, Oceania, Middle East, Africa Please contact an Onkyo distributo

Manualsnet FAQs

If you want to find out how the A 9050 Onkyo works, you can view and download the Onkyo A 9050, A 9030 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Onkyo A 9050 as well as other Onkyo manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Onkyo A 9050. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Onkyo A 9050, A 9030 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Onkyo A 9050, A 9030 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Onkyo A 9050, A 9030 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Onkyo A 9050, A 9030 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Onkyo A 9050, A 9030 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.