Öhlins 3500003 Control Unit Mounting Instructions PDF

1 of 4
1 of 4

Summary of Content for Öhlins 3500003 Control Unit Mounting Instructions PDF

Ducati Multistrada 1200S Suspension Control Unit

35000-03 Mounting Instructions and Set-up Guide

Note! Before installing this product, check the contents of the kit. If anything is missing, please contact an hlins dealer.

Note! This product is only applicable for Ducati Multistrada 1200S 2010-2012.

Warning! Before installing this product, read this document thouroughly. If you have any questions please contact an hlins dealer.

Kit Contents

Description Part No Pcs

SCU 35000-03 1 Sticker Mechatronic S 00191-46 2

2/4

1 Put the motorcycle on a stand.

2 Remove the seat.

3 Disconnect the negative battery terminal.

4 Remove the plastic side fairing on the left side of the seat.

5 Locate the original suspension control unit in the rubber mount. Disconnect the connector and remove the original suspension control unit from the rubber mount.

MoUNtING INStrUCtIoNS Warning!

It is advisable to have an hlins dealer install the SCU.

Warning! If working on a raised vehicle, ensure it is securely supported so that it will not tip.

Note! Before mounting this product clean the vehicle thoroughly.

Note! When working on this product, always see the Vehicle Service Manual for vehicle specific procedures and important data.

6 Insert the SCU (35000-03) in the rubber mount and connect the connector. Make sure it connects properly. You should hear a notice- able click.

Warning! Ensure to connect the connector properly. You should hear a noticeable click. If you have any questions regarding proper installation, please contact an hlins dealer.

7 Reinstall the plastic side fairing.

8 Reconnect the negative battery terminal.

9 Reinstall the seat.

10 Turn on the ignition and the electronic preload adjuster will calibrate at the first start-up.

11 Go to User Interface for further information.

3/4

USer INterfaCe How to operate The hlins SCU (35000-03) is operated in the same way as the original SCU, by the menu buttons on the left handlebar. See the vehicle manual for menu description.

activate event Based Control The Event Based Control is a feature that changes suspension setting while riding.

to activate event Based Control Enter the suspension settings menu in the dashboard. Set according to the following:

Front compression 1 Front rebound 1 Rear compression 1 Rear rebound 1

Note! When Event Based Control is desired, the suspension setting must be set according to the table above.

engine mode When Event Based Control is enabled the function depends on the engine mode select- ed in the set up.

100hp Comfort mode adjusts the damp- ing with vehicle speed to optimize comfort while maintaining enough stability. Default engine mode in URBAN and ENDURO set up.

150hp low

touring mode adjusts the damp- ing for best combination of agility and comfort. Default engine mode in TOURING set up.

150hp high

Sport mode adjusts the damping during acceleration and braking to optimize sport performance. Default engine mode in SPORT set up.

A suspension mode is the combination of set up (SPORT, TOURING, URBAN and ENDURO) and the load selection (rider, rider with luggage, two riders and two riders with luggage). This gives a total of 16 suspension modes. Example Riding mode; SPORT and rider only. If (1,1,1,1) is set the Event Based Control is only enabled at this suspension mode and load selection. All other modes are working with their individual damping set-up.

rear preload set up Adjust in the preload menu on the dashboard.

Suspension settings menu Engine mode

hlins Racing AB Box 722

S-194 27 Upplands Vsby, Sweden Phone +46 8 590 025 00

fax +46 8 590 025 80

hlins Racing AB. All rights reserved. Any reprinting or unauthorized use without the written permission of hlins Racing AB is prohibited.

hlins products are subject to continuous improvement and development, therefore, although these instructions include the most up-to-date information available at the time of printing, minor updates may occur.

To find the latest information contact an hlins distributor.

Please contact hlins if you have any questions regarding the

contents in this document.

Set-UP Data

Part no. MI_35000-03_0 Issued 2013-04-26

front fork Setting translation table The adjustment range is wider for the hlins SCU which enables a softer setting position at position 32 than for the original SCU. To keep your fixed setting see the translation table below.

adjustment range Shock absorber: (same as original) Front fork :

hlins SCU front fork setting

original SCU front fo

Manualsnet FAQs

If you want to find out how the 3500003 Öhlins works, you can view and download the Öhlins 3500003 Control Unit Mounting Instructions on the Manualsnet website.

Yes, we have the Mounting Instructions for Öhlins 3500003 as well as other Öhlins manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Mounting Instructions should include all the details that are needed to use a Öhlins 3500003. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Öhlins 3500003 Control Unit Mounting Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Öhlins 3500003 Control Unit Mounting Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Öhlins 3500003 Control Unit Mounting Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Öhlins 3500003 Control Unit Mounting Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Öhlins 3500003 Control Unit Mounting Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.