Morphy Richards 332102 Speed Steam Pro Instruction Booklet v2 PDF

Steam Generator

RN332102 MUK Rev1

Please read and keep these instructions for future use

IMPORTANT: For extra protection against limescale, use a mixture of 50% tap water mixed with 50% deionised, distilled or demineralised water (available at most large supermarkets). Never use more than 50% deionised, distilled or demineralised water and never use scented water or ironing water. Failure to maintain your product will invalidate your guarantee.

*Register at www.morphyrichards.co.uk/support UK and Ireland customers only

IF YOU HAVE ANY DIFFICULTY WITH THIS PRODUCT, INSTEAD OF TAKING IT BACK TO THE RETAILER, TRY:

1. The instruction booklet 2. Refer to www.morphyrichards.com 3. Or call our helpline: UK: 0344 871 0944, EIRE: 1800 409 119 (For UK & Eire customers only)

Register your guarantee online: www.morphyrichards.co.uk/support We'll keep you updated with special offers, competitions and important product information.

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 1

2

The use of any electrical appliance requires the following common sense safety rules. Please read these instructions carefully before using the product.

Important safety instructions

WARNING: Disconnect from the mains supply before carrying out any routine maintenance. WARNING: Misuse of the appliance could cause personal injury. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Keep the steam generator and its cord out of reach of children less than 8 years of age at all times. The steam generator must not be left unattended while it is connected to the supply mains. The steam generator must be used and rested on a stable surface. When placing the iron on the steam generator base, ensure that the surface on which the base is placed is stable. The steam generator is not to be used if it has been dropped, if there are visible signs of damage or it is leaking. The filling aperture may be opened during use, due to the design of the system. Do not operate with a damaged steam/supply cord or grommet, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 2

3

Important safety instructions ........................................................ Electrical requirements .................................................................. Steam generator overview ............................................................. Control panel overview ................................................................... Temperature guide .......................................................................... Before use ........................................................................................ Location ........................................................................................... Using the Steam Generator ........................................................... Steam boost button ........................................................................ Features ........................................................................................... Maintenance .................................................................................... Emptying and storing ..................................................................... Contact us ....................................................................................... Troubleshooting .............................................................................. Guarantee ........................................................................................

Contents 2 3 4 5 5 6 6 6 & 7 8 8 9 &10 10 10 11 12

Personal safety CAUTION - HOT:

Burns can occur from touching hot parts, hot water or steam, or the iron rest plate.

WARNING: Never direct steam at electrical components or fittings. If in doubt about the suitability of steam for cleaning an appliance, contact the appliance manufacturer for advice prior to cleaning.

WARNING: Never touch the plug or cable with wet hands.

WARNING: Nozzles and tools will be hot after use. Allow to cool before attempting to remove.

WARNING: Do not discharge the steam towards people or animals. Danger of scalding.

To protect against fire, electric shock and personal injury, do not immerse cord, plug or steam generator in water or other liquid.

The plug should be removed from the wall socket after use, before cleaning, filling or changing the accessories, or carrying out user maintenance.

Location Do not use or keep this product outside.

Do not store the appliance near hot surfaces eg. ovens or heating appliances.

Mains cable WARNING: A damaged or severed

mains cable fitted with a plug should never be connected to the mains supply. It must be destroyed, as a damaged cable becomes hazardous if connected to a power socket.

Do not let the mains lead come into contact with the hot soleplate of the iron.

Do not allow the mains lead to become strained.

Product safety WARNING: Always test on an

inconspicuous area first. Never use on materials that can not resist high temperature, such as dralon, natural fur etc.

Never modify the appliance in any way.

Other safety considerations Do not use any chemical detergents, perfumes, alcohol or descaler etc in water.

Repairs to electrical appliances are only to be undertaken by trained personnel.

Unprofessional repairs can be dangerous for users.

Use only genuine Morphy Richards spare parts and accessories.

The appliance must not be left unattended while connected to the supply mains.

This appliance is intended for domestic use only. Misuse or use for commercial or any other purpose will render the guarantee invalid.

Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A.C. (Alternating Current).

If the socket outlets in your home are not suitable for the plug supplied with this appliance, the plug should be removed by trained authorised personnel and the appropriate one fitted.

WARNING: This appliance must be earthed.

Should the fuse in the mains plug require changing, replace it with a fuse of the same rating as originally fitted.

STEAM

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 3

4

(1) Filling aperture

(2) Dirty water chamber

(3) Dirty water emptying hole

(4) Temperature indicator light

(5) Temperature dial

(6) Soleplate

(7) Steam trigger

(8) Iron handle

(9) Iron-to-base lock

(10) Cable support

(11) Water tank handle

(12) Detachable water tank

(13) Iron locking hook

(14) Iron rest plate

(15) Rear docking slot

(16) Control panel (see page 5)

(17) Base unit

(18) Cord storage groove

(19) Cord storage

Steam generator overview

4

5

6

18 19

7 8

11

16

17

9

10

12

13 15141 3

2 3

1

2

18

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 4

5

Control panel overview

Descale indicator (20) When the system requires cleaning, the descale indicator (20) will illuminate. When this happens, follow the instructions under Maintenance on page 9.

Low water indicator (21) This indicator will illuminate when there is insufficient water in the tank to produce steam.

On/Off power indicator (22) This indicator illuminates when the unit is turned on, and extinguishes if the appliance is turned off or has entered auto shut-off mode after not being used for 10 minutes.

On/Off power button (23) Connect to a mains outlet and press the On/Off power button (23). The button will illuminate and

the low steam level indicator (25a) will flash. To turn off, press and hold the On/Off power button for 3 seconds.

Steam level select button (24) Press the steam level select button (24) to toggle through the steam levels. Each press cycles the level from low to medium to high, back to low and so forth.

Steam level indicators (25) Press the steam level select button (24) to adjust the steam level. The steam level selected will be displayed by illumination of the relevant steam level indicator: low (25a), medium (25b) or high (25c). See step 5 of Using the Steam Generator on page 7.

Heat setting markings on the temperature dial of all Morphy Richards irons match those of the International Textile Care Labelling Code

Temperature guide

Symbol (120C Max) Cool (160C Max) Warm (210C Max) Hot MAX setting

Control dial positions

Do not iron

Fabric Nylon, Acetates, synthetic fabrics

Wool, Polyester mixtures

Cotton, Linen Rayon, Rayon mixtures

Ironing Iron on wrong side, if moisture required, use damp cloth (not Acetate)

Fabrics requiring this setting usually require steam pressing.

Steaming

Without steam

Steam level setting (see step 5 of Using the Steam Generator on page 7)

No steam (see Dry ironing on page 8)

Low Medium / High High

Low water indicator

21

Low steam level indicator

25a Medium steam level indicator

25b High steam level

indicator 25c

Descale indicator

20

On/Off power indicator

22

On/Off power button

23

Steam level select button

24

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 5

6

Using the Steam Generator

Plug the appliance into a mains outlet. Press the On/Off power button (23), it will beep and the low steam level indicator (25a) will flash.

2

Remove the detachable water tank (12) by pulling the water tank handle (11), and fill with water through the filling aperture (1) to the max fill line. Replace the water tank.

IMPORTANT: Never fill the dirty water chamber (2).

I IMPORTANT: FOR EXTRA PROTECTION AGAINST LIMESCALE, USE A MIXTURE OF 50% TAP WATER MIXED WITH 50% DEIONISED, DISTILLED OR DEMINERALISED WATER (AVAILABLE AT MOST LARGE SUPERMARKETS).

NEVER USE MORE THAN 50% DEIONISED, DISTILLED OR DEMINERALISED WATER AND NEVER USE SCENTED WATER OR IRONING WATER.

Never use battery topping up fluid or water containing any substances like starch, sugar, fragrant additives or defrosted water from a refrigerator. NOTE: Please see point 2 of Exclusions on page 12.

Re-filling during use If the water level is too low, the unit will not produce steam. If this happens, refill the detachable water tank (12) with water.

1

Remove any protective cover from the soleplate (6) and the base unit (17). Unwind and straighten the power cord and steam supply cord.

Locate the steam generator horizontally on the iron rest plate of your ironing board (if large enough) or on a heat resistant stand at the same height as your ironing board or below it. Always ensure the steam generator is on a firm surface when ironing.

WARNING: Do not use the product on a surface which could be damaged by heat or steam such as a worktop or a polished wood surface. If in doubt, contact Morphy Richards.

Location

Before use

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 6

7

Turn the temperature dial (5) to suit the garment (see Temperature guide on page 5). The temperature indicator light (4) illuminates until the temperature is reached. Begin ironing when the temperature indicator light goes out.

It is advised to begin with cool fabrics (see above) and work up to higher settings. An iron heats up quicker than it cools down so youll save time and electricity.

If you turn the temperature dial (5) down from a hot setting to a cooler setting, wait until the temperature indicator light (4) illuminates and goes out again (indicating the correct temperature has been reached) before you continue ironing.

3

Unlock the iron from its storage position on top of the base unit (17) by sliding the iron-to-base lock (9) to the position marked with an unlocked padlock icon - the iron can then be lifted off the base unit.

WARNING: The soleplate will be hot.

During use, the iron may be rested on the iron rest plate (14).

4

Using the Steam Generator (continued)

75

Press the steam level select button (24) to select your desired steam level. The selected steam level will be displayed by illumination of the relevant steam level indicator (25). The steam level indicator will stop flashing and illuminate constantly when the selected steam level is reached.

WARNING: The steam supply cord will get hot during use.

When you have finished ironing, turn off the appliance by pressing and holding the On/Off power button (23) for three seconds. A beep will be heard and all the indicators on the control panel (16) will be extinguished.

Disconnect the plug from the mains outlet.

NOTE: The product may occasionally produce a pumping sound during steam ironing. This is normal and is caused by water being pumped from the water tank to the steam generator.

6

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 7

8

Dry ironing To use your steam generator as a dry iron only, follow steps 2, 3 and 4 of Using the Steam Generator on pages 6 and 7. You do not need to put water in the tank or select a steam level. Press the steam trigger (7) at least once every 10 minutes, or the product will automatically turn off.

Auto shut-off If the iron is not used for 10 minutes, the product will automatically turn off for safety and to save energy, and a beep will be heard.

To restart, press the On/Off power button (23) (see step 2 of Using the Steam Generator on page 6) and wait for the temperature to rise again.

Steam function During steaming, small amounts of water may be ejected from the soleplate (6). This is normal and can be avoided by using the steam for short amounts of time and only when the iron is at the correct temperature (the temperature indicator light (4) on the iron goes out when ready).

Sudden jolts of the boiler unit can also cause water droplets on the soleplate; therefore, do not move the base unit during ironing.

We recommend for first time ironing that you iron over an old towel.

Vertical steam Vertical steam is useful for removing creases from hanging clothes, curtains, upholstery, etc. Hold the iron between 1cm and 2cm away from the item and press the steam trigger (7) twice in quick succession for a longer boost of steam. To turn the steam boost off, press the steam trigger again.

WARNING: Do not use the vertical steam feature on clothes that are being worn.

Features

7

Steam boost button

The steam boost function is ideal for relaxing the fibres of tougher fabrics (like jeans and linen) and getting rid of those stubborn, hard to reach creases.

To produce a steam boost during ironing, simply press the steam trigger (7) twice in quick succession. To turn this off, press the steam trigger again.

To conserve water in the tank, we recommend you switch off the steam boost when the iron is not in use.

7

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 8

9

Auto-clean descale function Each time approximately 5L of water has been used in the steam generator, it will need to run an auto-clean cycle. When the product is fully cooled down and first switched on, it will draw water from the detachable water tank (12) to flush the boiler, emptying dirty water and limescale into the dirty water chamber (2). For this short time, the descale indicator (20) will flash and you will be unable to use the product to iron.

If there is not sufficient water to operate this function, the product will alert you with the low water indicator (21) and the process will be paused until the tank is refilled and replaced.

WARNING: During the auto-clean process, the water ejected from the machine is very hot, so do not remove the water tank until the auto-clean process is finished.

The auto-clean process will take approximately 3 minutes, after which the steam generator will be ready for normal operation again. The flashing descale indicator (20) will extinguish and the low steam level indicator (25a) will flash, indicating that the steam generator is readying itself for the low steam level setting.

After ironing, switch off the steam generator at the On/Off power button (23) and unplug from the mains outlet. If the auto-clean function has activated and completed, wait for the steam generator to cool down completely. Remove the detachable water tank and tip the dirty water from the dirty water emptying hole (3).

IMPORTANT: Ensure the dirty water is emptied after each auto-clean cycle to prevent overflow.

WARNING: Dirty water in the dirty water chamber (2) will be hot after the auto-clean process, so take care when pouring it out.

To clean a coated soleplate Do not use scouring powder or solution as this could cause damage to the coating.

If any man made fibres fuse to the soleplate (6), set the iron at the MAX position and pass it over a clean piece of cotton to draw the deposit off the surface.

To clean the exterior Allow the unit to cool and wipe over with a damp cloth and mild detergent, then wipe dry.

Maintenance

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 9

10

Allow the appliance to cool.

Remove the detachable water tank (12) by pulling the water tank handle (11). Empty the water tank. Once the water tank is empty, re-attach it to the base unit (17).

Wrap the power cord and steam supply cord loosely in long loops. Gently push the looped cords along the cord storage groove (18) into the cord storage (19) areas on either side of the base unit (17), one cord per side. Avoid kinking of cables, particularly where they meet the base unit.

WARNING: To avoid internal damage, do not squeeze the cables where folded. Do not pull too tightly on the steam supply cord or on the cable support (10) when looping the power cord and steam supply cord. Damage to cables caused by wrapping too tightly will not be covered by the guarantee.

Storing the steam iron

Lock the iron into the storage position on top of the base unit (17) by sliding the tip of the soleplate (6) under the iron locking hook (13). With the lower end of the soleplate in position adjacent to the lower end of the iron rest plate (14), slide the iron-to-base lock (9) to the position marked with a padlock icon - this secures the soleplate in place. Once the iron-to-base lock is locked securely, the iron can be carried by the iron handle (8).

Helpline If you are having a problem with your appliance, please call our Helpline, as we are more likely to be able to help than the store you purchased the item from. Please have the product name, model number and serial number to hand when you call to help us deal with your enquiry quicker.

UK Helpline: 0344 871 0944 IRE Helpline: 1800 409 119 Spares: 0344 873 0710

Talk To Us

If you have any questions or comments, or want some great tips to help you get the most out of your products, join us online:

Blog: www.morphyrichards.co.uk/blog Facebook: www.facebook.com/morphyrichardsuk Twitter: @loveyourmorphy Website: www.morphyrichards.com

Contact us

Emptying and storing

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 10

11

Troubleshooting

No power or not heating up.

Overheating or not getting hot enough.

Not steaming or poor steam.

Dripping from the holes in the soleplate.

Tripping Electrics.

Steams continuously.

Problem Solution

The auto-clean does not operate / the descale indicator stays ON.

1. Check the fuse and try a new fuse with the same rating. 2. Try a different appliance in the socket as it may be the socket that is at fault.

3. Check that the auto shut off has not operated. 4. Ensure the iron is switched on by pressing the On/Off power button. 5. Check the temperature dial has not been set to MIN.

1. Adjust the temperature dial to ensure the setting matches that recommended on the garment or refer to the temperature guide section.

2. Allow the iron to reach temperature and stabilise for 1-2 minutes if it has just been plugged in, or has just been woken up from auto shut off.

1. Check that there is enough water in the tank.

2. If the irons auto shut off feature has activated, wake up the iron and allow it to reach temperature before using steam.

1. Ensure the temperature is set within the steam band (refer to the temperature guide section). The iron will not be hot enough to produce steam if the temperature is set too low.

2. The steam level should be set lower if the temperature is set lower (refer to the temperature guide section) to prevent it from dripping.

3. If the irons auto shut off feature has activated, wake up the iron and allow it to reach temperature before using steam.

4. Ensure the correct 50/50 water combination is used.

1. Try using a different socket. 2. Ensure there are no other appliances being used on the same set of sockets as the iron.

1. The steam boost feature may have been activated by pressing the steam trigger twice in quick succession. This can be turned off by pressing the steam trigger again.

1. The unit must have completely cooled down before the auto-clean will operate. Let it cool down overnight before trying again.

2. The clean water tank must be filled to MAX with clean water and connected properly.

3. The descale indicator will extinguish only after the auto-clean process has been completed properly.

The product occasionally produces a pumping sound during steam ironing.

1. This is normal and is caused by water being pumped through the steam pump. The pump is controlled by the unit automatically to keep the boiler up to pressure.

RN332102 MUK Rev1.qxp_IB 13/03/2020 11:29 Page 11

RN332102 MUK Rev1 03/20

Your standard 1 year guarantee is extended for an additional 2 years when you register the product within 28 days of purchase with Morphy Richards. If you do not register the product with Morphy Richards within 28 days, your product is guaranteed for 1 year. To validate your 3 year guarantee register with us online at www.morphyrichards.co.uk Or call our customer registration line UK 0344 871 0242 IRE 1800 409 119

N.B. Each qualifying product needs to be registered with Morphy Richards individually.

Please note that the 3 year guarantee is only available in the UK and Ireland. Please refer to the 1 year guarantee for more information.

It is important to retain the retailers receipt as proof of purchase. Staple your receipt to this back cover for future reference.

Please quote the following information if the product develops a fault. These numbers can be found on the base of the product.

Model no.

Serial no.

All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase, it should be returned to the place of purchase for it to be replaced.

If the fault develops after 28 days and within 12 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown.

You may be asked to return a copy of proof of purchase.

Subject to the exclusions set out below (see Exclusions), the faulty appliance will then be repaired or replaced as appropriate and dispatched usually within 7 working days of receipt.

If, for any reason, this item is replaced or repaired during the 1 year guarantee period, the guarantee on the new item will be calculated from original purchase date. Therefore it is vital to retain your original till receipt or invoice to indicate the date of initial purchase.

To qualify for the 1 year guarantee, the appliance must have been used according to the instructions supplied. For example, water should be emptied after each use.

Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where:

1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturers recommendations or where the fault has been caused by power surges or damage caused in transit.

2 The fault is caused by limescale build-up.

3 The cables are damaged due to wrapping too tightly or excessive kinking.

4 The appliance has been used on a voltage supply other than that stamped on the products.

5 Repairs have been attempted by persons other than our service staff (or authorised dealer).

6 The appliance has been used for hire purposes or non domestic use.

7 The appliance is second hand.

8 Morphy Richards reserves the right not to carry out any type of servicing under the guarantee at its discretion.

This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. Morphy Richards products are intended for household use only. See usage limitations within the location safety instructions.

Morphy Richards has a policy of continuous improvement in product quality and design. The company, therefore reserves the right to change the specification of its models at any time.

For electrical products sold within the European Community. At the end of the electrical products useful life, it should not be disposed of with household waste.

Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country

ExclusionsRegistering your 3 year guarantee

Your 1 year guarantee

Disclaimer

The After S