Contents

Mitsubishi GOT1000 1D7M54 RGB Input User's Manual PDF

1 of 26
1 of 26

Summary of Content for Mitsubishi GOT1000 1D7M54 RGB Input User's Manual PDF

User's Manual

Thank you for choosing Mitsubishi Electric Graphic Operation Termi- nal (GOT).

MODEL GT15V-75V4R1 Video/RGB Input Unit MODEL GT15V-75V4 Video Input Unit MODEL GT15V-75R1 RGB Input Unit

Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.

MODEL GT15V-75V4R1-U

MODEL CODE

1D7M54

IB(NA)-0800348-G(1706)MEE

SAFETY PRECAUTIONS (Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly. The precautions given in this manual are concerned with this product. In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".

Note that the caution level may lead to a serious accident according to the circumstances. Always follow the instructions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.

WARNING

CAUTION

A-1

[DESIGN PRECAUTIONS]

[MOUNTING PRECAUTIONS]

Do not bunch the control wires or communication cables with the main circuit or power wires, or lay them close to each other. As a guide, separate the lines by a distance of at least 100mm (3.94 inches) otherwise malfunctions may occur due to noise.

Be sure to shut off all phases of the external power supply used by the system before mounting or removing this unit onto/from the GOT. Not doing so can cause the unit to fail or malfunction.

Use this unit in the environment that satisfies the general specifications described in the User's Manual for the GOT used. Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

Tighten the mounting screws within the specified torque range. Undertightening can cause the GOT to drop, short circuit or malfunction. Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the GOT.

Do not touch the conductive and electronic parts of the unit directly. Doing so can cause a unit malfunction or failure.

CAUTION

WARNING

CAUTION

A-2

[WIRING PRECAUTIONS]

Be sure to shut off all phases of the external power supply used by the system before wiring. Failure to do so may result in an electric shock, product damage or malfunctions.

Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT. Not doing so can cause a fire, failure or malfunction.

Make sure to securely connect the cable to the connector of unit. Incorrect connection may cause malfunctions.

Do not hold the cable by hand and pull it out from the unit. When removing the cable from the unit, make sure to hold the connector by hand and pull it. Failure to do so may cause malfunctions or damage to the unit or cable.

Solder the coaxial cable connector correctly. Incomplete soldering may cause a malfunction.

WARNING

CAUTION

A-3

[STARTUP/MAINTENANCE PRECAUTIONS]

[DISPOSAL PRECAUTIONS]

[TRANSPORTATION PRECAUTIONS]

When power is on, do not touch the terminals. Doing so can cause an electric shock or malfunction.

Before starting cleaning, always shut off GOT power externally in all phases. Not doing so can cause a unit failure or malfunction. Undertightening can cause a short circuit or malfunction. Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

Do not disassemble or modify the unit. Doing so can cause a failure, malfunction, injury or fire.

Do not drop the module or subject it to strong shock. A module damage may result.

Before touching the unit, always touch grounded metal, etc. to discharge static electricity from human body, etc. Not doing so can cause the unit to fail or malfunction.

When disposing of the product, handle it as industrial waste.

Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the User's Manual for the GOT used, as they are precision devices. Failure to do so may cause the unit to fail. Check if the unit operates correctly after transportation.

WARNING

CAUTION

CAUTION

CAUTION

A-4

REVISIONS * The manual number is noted at the lower right of the top cover.

2006 MITSUBISHI ELECTRIC CORPORATION

Print Date *Manual Number Revision

Mar., 2006 IB(NA)-0800348-A First edition

Feb., 2007 IB(NA)-0800348-B

Chapter1, Section 2.4.1

Compliance with the EMC and Low Voltage Directives

Jul., 2007 IB(NA)-0800348-C

Compliance with the EMC and Low Voltage Directives, Chapter 2, 3, 4

Jun., 2009 IB(NA)-0800348-D

Compliance with the EMC and Low Voltage Directives

Jun., 2011 IB(NA)-0800348-E

Compliance with the Radio Waves Act (South Korea)

May, 2015 IB(NA)-0800348-F

Cover

Jun., 2017 IB(NA)-0800348-G

Cover

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.

Partial addition

Addition

Partial corrections

Partial corrections

Addition

Partial corrections

Partial corrections

A-5

A-6

CONTENTS

1. OVERVIEW ....................................................................................................1

2. SPECIFICATIONS .........................................................................................4

2.1 Video input unit specifications .................................................................4

2.2 RGB input unit specifications ...................................................................5

2.3 Video/RGB input unit specifications ........................................................ 6

2.4 Cable specifications .................................................................................7

2.4.1 Specifications of the cables (coaxial cables) used when displaying video images ..................................................................7

2.4.2 Specifications of the cables (9-core combined cables) used when displaying RGB screens ...................................................... 10

3. PART NAMES AND EXTERNAL DIMENSIONS ......................................... 11

3.1 Part names and external dimensions of the video input unit .................11

3.2 Part names and external dimensions of the RGB input unit ..................12

3.3 Part names and external dimensions of the video/RGB input unit ........13

3.4 External dimensions of the extension interface relay board ..................14

4. INSTALLATION PROCEDURE ................................................................... 15

A-7

Packing List The following items are included.

Compliance with the EMC and Low Voltage Directives To configure a system meeting the requirements of the EMC and Low Voltage Directives when incorporating the Mitsubishi GOT (EMC and Low Voltage Directives compliant) into other machinery or equipment, refer to "EMC AND LOW VOLTAGE DIRECTIVES" of the General Description included with the GOT used. The CE mark, indicating compliance with the EMC and Low Voltage Directives, is printed on the rating plate of the GOT.

Model Product Quantity

GT15V-75V4

Video input unit 1

Mounting screw set (2 screws,2 stickers) 2

Extend interface relay board 1

GT15V-75R1

RGB input unit 1

Mounting screw set (2 screws,2 stickers) 2

Extend interface relay board 1

GT15V-75V4R1

Video/RGB input unit 1

Mounting screw set (2 screws,2 stickers) 2

Extend interface relay board 1

Manuals The following shows manuals relevant to this product.

For relevant manuals, refer to the PDF manuals stored in the DVD-ROM for the drawing software used.

Detailed Manual

Manual name Manual number (Model code)

GT15 User's Manual (Sold separately)

SH-080528ENG (1D7M23)

GOT1000 Series Connection Manual (Microcomputer, MODBUS Products, Peripherals) for GT Works3

(Sold separately)

SH-080871ENG (1D7MC5)

Relevant Manuals

1. OVERVIEW

This User's Manual is related to the following units.

MODEL GT15V-75V4 Video Input Unit (hereinafter referred to as the Video Input Unit)

MODEL GT15V-75R1 RGB Input Unit (hereinafter referred to as the RGB Input Unit)

MODEL GT15V-75V4R1 Video/RGB Input Unit (hereinafter referred to as the Video/RGB Input Module).

When mounting the above units with the GT1585V-STBA, GT1575V-STBA (hereinafter referred to as GOT), the images taken by video cameras or screens on personal computers can be displayed on the GOT. The video input unit can display the images taken by up to 4 video cameras on the GOT. GOT can be used as a vision sensor monitor.

*1: Power on the video camera simultaneously with the GOT. *2: Power supply for the camera may be necessary depending on the

vision sensor to be used.

Image data

GOT +

GT15V-75V4

Camera power pack*2

Video camera*1

Video camera

Vision sensor (AS50VS or other)

1

The RGB input unit can display a personal computer display on the GOT. Video input is also available using an RGB output type vision sensor.

*1: When connecting with a personal computer, ground wire of the computer should be grounded.

For the video/RGB input unit, functions of both video input unit (GT15V-75V4) and RGB input unit (GT15V-75R1) are available.

When connecting to a personal computer

GOT+GT15V-75R1

*1

When connecting to a video camera using an RGB output type vision sensor.

RGB output type vision sensor

GOT+GT15V-75R1

A 1254

348B

GOT*3

GT15V-75V4R1

Video camera*2

Computer PLCs for line control

Do n ot mou nt not desmou nt a mo dule w hile th e powe r is supp lied.

CAUTION

*1

2

*1: When connecting the unit to a personal computer, ground wire of the computer should be grounded.

*2: Power on the video camera simultaneously with the GOT. *3: Video images and personal computer screens cannot be displayed

on the GOT at the same time.

To use the Video input unit, RGB input unit and Video/RGB input unit, make the Communication Settings. For setting details, refer to GOT1000 Series Connection Manual.

For details of system configuration, refer to GOT1000 Series Connection Manual. For video input and RGB input functions, refer to the GT Designer2 Version Screen Design Manual.

3

2. SPECIFICATIONS

2.1 Video input unit specifications

*1: Compatible with PAL and CCIR formats only. *2: The length of a cable differs depending on the specifications of the

vision sensor and video camera to be used. Be sure to use the cable with specified length for the vision sensor and video camera to be used.

Item Specifications

Video input section

Video input system

Color NTSC format, PAL format (interlaced format)

Monochrome EIA format, CCIR format (interlaced format)

Number of video input channels

4 channel

Input signal IVp-p, 75 , composite signal

Display size [dot's] 640x480 (possible to reduce to 320x240, 160x120) 720x480 (possible to reduce to 360x240, 180x120) *1

Video external connection method

Coaxial cable

Applicable wire size 75 coaxial shield cable

Maximum cable length Refer to the specifications of the personal computer, vision sensor and video camera to be used *2

Internal current consumption (3.3VDC)

0.7A

Weight 0.2kg (0.44Ib)

4

2.2 RGB input unit specifications

*1: The length of a cable differs depending on the specifications of the personal computer and vision sensor to be used. Be sure to use the cable with specified length for the personal computer and vision sensor to be used.

Item Specifications

RGB input section

RGB input method (dot's) Analog RGB(SVGA; 800x600, VGA; 640x480)

Number of video input channels

1 channel

Input image signal 1Vp-p, 75

Synchronizing signal TTL, 1k

Display size [dot's] 800 600 (refresh rate 60, 72, 75 [Hz]) 640 480 (refresh rate 60, 72, 75, 85 [Hz])

RGB external connection method

D-Sub15 pin

Applicable wire size 9-core combined cable (recommended)

Maximum cable length Refer to the specifications of the personal computer, vision sensor and video camera to be used *1

Internal current consumption (3.3VDC)

0.91A

Weight 0.17kg (0.37Ib)

5

2.3 Video/RGB input unit specifications

*1: Compatible with PAL and CCIR formats only. *2: The length of a cable differs depending on the specifications of the

personal computer, vision sensor and video camera to be used. Be sure to use the cable with specified length for the personal computer, vision sensor and video camera to be used.

*3: Both video images and RGB screens cannot be displayed on the GOT at the same time.

Item Specifications

Video input section *3

Video input system

Color NTSC format, PAL format (interlaced format)

Monochrome EIA format, CCIR format (interlaced format)

Number of video input channels

4 channel

Input signal IVp-p, 75 , composite signal

Display size [dot's] 640x480 (possible to reduce to 320x240, 160x120) 720x480 (possible to reduce to 360x240, 180x120) *1

Video external connection method

Coaxial cable

Applicable wire size 75 coaxial shield cable

RGB input section *3

RGB input method (dot's) Analog RGB(SVGA; 800x600, VGA; 640x480)

Number of video input channels

1 channel

Input image signal 1Vp-p, 75

Synchronizing signal TTL, 1k

Display size [dot's] 800 600 (refresh rate 60, 72, 75 [Hz]) 640 480 (refresh rate 60, 72, 75, 85 [Hz])

RGB external connection method

D-Sub15 pin

Applicable wire size 9-core combined cable (recommended)

Maximum cable length Refer to the specifications of the personal computer, vision sensor and video camera to be used *2

Internal current consumption (3.3VDC)

0.95A

Weight 0.21kg (0.46Ib)

6

2.4 Cable specifications

The following shows the cable specifications, connection diagram, and connector used for the video input unit, RGB input unit, and video/RGB input unit.

2.4.1 Specifications of the cables (coaxial cables) used when displaying video images

(1) Coaxial cable Use high frequency coaxial cable "3C-2V" or "5C-2V" (conforms to JIS C 3501). The following shows the coaxial cable specifications.

(2) Connector

GOT connector Use BNC connector for GOT side connector. The following shows the connection method for BNC connector and coaxial cable.

Item 3C-2V 5C-2V

Construction

Cable diameter 5.4mm (0.21in.) 7.4mm (0.29in.)

Allowable bending radius

22mm (0.87in.) or more 30mm (1.18in.) or more

Internal conductive material diameter

0.5mm (0.02in.) (Annealed copper wire)

0.8mm (0.03in.) (Annealed copper wire)

Insulation material diameter

3.1mm (0.12in.) (Polyethylene) 4.9mm (0.19in.) (Polyethylene)

External conductive material diameter

3.8mm (0.15in.) (Single annealed copper wire mesh)

5.6mm (0.22in.) (Single annealed copper wire mesh)

Applicable connector plug

Connector plug for 3C-2V (BNC- P-3-N1-CAU is recommended.)

Connector plug for 5C-2V (BNC- P-5-N1-CAU is recommended.)

Internal condcuctive material

Insulating material

External conductive material

Sheath

7

(a) Construction of BNC connector and coaxial cable.

(b) Connecting the BNC connector with the coaxial cable.

Parts of the BNC connector Construction of coaxial cable

1) Remove the outer sheath of the coaxial cable in the specified dimension as shown left.

2) Slip a nut, a washer, a gasket, and a clamp through the coaxial cable as shown left, and loosen the outer conductor.

3) Cut off the insulating material and internal conductive material in the specified dimensions as shown left. Cut off the outer conductor in the same dimension as the taper part of the clamp, and extend it over the clamp.

4) Solder the contact to the tip of the internal conductive material.

5) Insert the contact assembly of 4) into the plug shell, and engage the plug shell with the nut.

Clamp Contact

GasketWasherNut

Plug shell

Outer sheath

Outer conductor

Insulating material Internal conductive material

15mm (0.59in.)

Remove the outer sheath.

Washer Nut

Gasket

Clamp

3mm (0.12in.)

6mm (0.24in.)

Insulating materialInternal conductive material

Clamp and outer conductor

Soldering

8

*1: Soldered part must not have excess solder mound. *2: The tail end of the contact must come into close contact with the cut

end of the insulating material. The contact must not be cutting in the insulating material.

*3: Apply solder quickly so that the insulating material will not be deformed by heat.

Connector at the video camera and vision sensor Use a connector applicable to the video camera or vision sensor to be used.

(3) Precautions for cable preparation The maximum cable length differs depending on the specifications of the video camera and vision sensor to be used. For details, refer to manuals for video camera and vision sensor. When a cable length gets longer, video signals are attenuated, and video images deteriorate. When using a cable exceeding the length described in the following table, it is recommended to correct video images using a video signal amplifier.

(4) Precautions for laying cable Consider wiring using double-shielded coaxial cable in places that are subject to large amounts of noise.

The 5C-2V connector plug is applicable to double-shielded coaxial cable. Connect the 5C-2V connector plug to the coaxial cable inside a double-shielded coaxial cable. Ground the shielded part outside a double-shielded coaxial cable as shown in the above figure.

Cable type Cable length [m] (feet)

3C-2V 100 (328.1)

5C-2V 200 (656.2)

Grounding

Mitsubishi Cable ... 5C-2V-CCY

Double-shielded coaxial cable

Internal conducter

Insulation material

External conductor

Sheath

External conductor (Grounding)

SheathEnlarged view of cable

9

2.4.2 Specifications of the cables (9-core combined cables) used when displaying RGB screens

(1) Cable specifications

(2) Connection diagram

(3) Connector

GOT side connector The following model is used for the GOT connector. Use a connector that matches the following connector. 15-pin D-sub (male) inch screw type Manufactured by DDK 17HE-R13150-73MC2

Connector at the personal computer and vision sensor Use the connector applicable to the personal computer and vision sensor.

(4) Precaution for cable creating The length of a cable differs depending on the personal computer and vision sensor to be used. Male the create within the range of personal computer and vision sensor specifications.

Item Specifications

Applicable cable Equivalent to SP23-23352A UL20276-SB

Applicable wire size 9-core combined cable (recommended)

1

6

2

7

3

8

5

10

13

14

4

9

11

12

15

R

RGND

G

GGND

B

BGND

GND

GND

HSYNC

VSYNC

GND

NC

GND

SDA

SCL

1

6

2

7

3

8

5

10

13

14

4

9

11

12

15

R

RGND

G

GGND

B

BGND

DGND

DGND

HSYNC

VSYNC

NC

NC

NC

NC

NC

GOT sidePersonal computer side

Twisted pair

75 Coaxical

10

3. PART NAMES AND EXTERNAL DIMENSIONS

3.1 Part names and external dimensions of the video input unit

Unit: mm (inch)

Dimensions of X when the video input unit is mounted to the GOT. 12.1 18 (0.71)

10.4 21 (0.83)

No. Name Description

1) Connector for video input

Connector for connecting a coaxial cable

2) Interface connector Connector mounted to the GOT

3) Extension connector Connector to which a back extension unit is installed

4) Connector for video/ RGB connection

Connector connecting with the video/RGB interface of GOT

5) Board fixing screw Screw for fixing the extend interface relay board

6) Mounting screw Mounting screws for fixing the unit to the GOT

7) Rating plate -

3)

6)

1)

2)

6) GOT main unit

7)

5)

19 .5

(0 .7

7)

X

17.5 (0.69)

18 (0.71)

18 (0.71)

34 (1.34)

8. 0

(0 .3

1)

4)

133 (5.24)

2.5 (0.10)

10 5

(4 .1

3)

98 (3

.8 6)

3 (0.12)

30 .5

(1 .2

0) 21

.5 (0

.8 5)

Unit : mm(inch)

11

3.2 Part names and external dimensions of the RGB input unit

Unit: mm (inch)

Dimensions of X when the RGB input unit is mounted to the GOT.

12.1 18 (0.71)

10.4 21 (0.83)

No. Name Description

1) Connector for RGB input

Connector for connecting 9-core combined cables

2) Interface connector Connector mounted to the GOT

3) Extension connector Connector to which a back extension unit is installed

4) Connector for video/ RGB connection

Connector connecting with the video/RGB interface of GOT

5) Board fixing screw Screw for fixing the extend interface relay board

6) Mounting screw Mounting screws for fixing the unit to the GOT

7) Rating plate -

GOT main unit

X

133 (5.24)

2.5 (0.10)

113.5 (4.47)

10 5

(4 .1

3) 98

(3 .8

6) 3

(0.12)

8. 0

(0 .3

1)

30 .5

(1 .2

0) 21

.5 (0

.8 5)

8. 5

(0 .3

3)

3)

6)

2)

6)

7)

1)

5)

4) Unit : mm(inch)

12

3.3 Part names and external dimensions of the video/RGB input unit

Unit: mm (inch)

Dimensions of X when the video/RGB input unit is mounted to the GOT.

12.1 18 (0.71)

10.4 21 (0.83)

No. Name Description

1) Connector for video input Connector for connecting a coaxial cable

2) Connector for RGB input Connector for connecting 9-core combined cables

3) Interface connector Connector mounted to the GOT

4) Extension connector Connector to which a back extension unit is installed

5) Connector for video/RGB connection

Connector connecting with the video/RGB interface of GOT

6) Board fixing screw Screw for fixing the extend interface relay board

7) Mounting screw Mounting screws for fixing the unit to the GOT

8) Rating plate -

GOT main unit4)

7)

1)

3)

7)

8)

6)

2)

19 .5

(0 .7

7)

X

17.5 (0.69)

18 (0.71)

18 (0.71)

34 (1.34)

26.0 (1.02)

8. 0

(0 .3

1) 8.

0 (0

.3 1)

8. 5

(0 .3

3)

5)

133 (5.24)

2.5 (0.10)

10 5

(4 .1

3)

98 (3

.8 6)

3 (0.12)

30 .5

(1

.2 0)

21 .5

(0 .8

5)

Unit : mm(inch)

13

3.4 External dimensions of the extension interface relay board

Unit: mm (inch)

64 (2.52)

2 4

( 0

.9 4

) 2

7 .5

( 1

.0 8

)

14

4. INSTALLATION PROCEDURE

The installation procedure for the video/RGB input unit is explained using the GT1575.

(1) Power off the GOT.

(2) Remove two extension unit covers of the GOT.

(3) Attach the extend interface relay board to the extend I/F-2 side on the GOT. After the installation, detach the connector cover from the extend interface relay board.

(4) Fit the video/RGB input unit in the GOT case.

(5) Fasten the video/RGB input unit by tightening its mounting screws (4 places) with tightening torgue 0.36 to 0.48 Nm.

4) 3)

Remove the connector cover

15

(6) Fasten the bus connection unit by tightening the board fixing screws (2 places) with the tightening torque of 0.36 to 0.48 Nm.

(7) When installing an extension unit on the unit that has been installed, remove the connector cover and the sticker. When not installing an extension unit on the unit that has been installed, in order to avoid receiving electrostatic, stick accessory stickers to cover the top of mounting screws (4 places). Keep the connector cover fixed. Keep the sticker stuck as it is.

Point

Remove the screws that fixes the extend interface relay board before removing the unit.(Above 6))

5) 6)

Sticker

Accessory sticker

Accessory sticker

Connector cover

16

MEMO

17

Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other than Mitsubishi products; and to other duties.

For safe use This product has been manufactured as a general-purpose part for general industries, and

has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.

Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi.

This product has been manufactured under strict quality control. However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.

Specifications subject to change without notice. Printed in Japan, June 2017.

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.

Country/Region Sales office/Tel Country/Region Sales office/Tel USA

Brazil

Mexico

Germany

UK

Italy

Spain

France

Czech

Turkey

Poland

Russia

Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A. Tel: +1-847-478-2100 Mitsubishi Electric do Brasil Comercio e Servicos Ltda. Avenida Adelino Cardana, 293, 21 andar, Bethaville, Barueri SP, Brasil CEP 06401-147 Tel: +55-11-4689-3000 Mitsubishi Electric Automation, Inc. Mexico Branch Mariano Escobedo #69, Col. Zona Industrial, Tlalnepantla Edo. Mexico, C.P.54030 Tel: +52-55-3067-7511 Mitsubishi Electric Europe B.V. German Branch Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany Tel: +49-2102-486-0 Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Hertfordshire, AL10 8XB, U.K. Tel: +44-1707-28-8780 Mitsubishi Electric Europe B.V. Italian Branch Centro Direzionale Colleoni - Palazzo Sirio, Viale Colleoni 7, Agrate Brianza (MB), Italy Tel: +39-039-60531 Mitsubishi Electric Europe B.V. Spanish Branch Carretera de Rubi 76-80-Apdo.420, 08190 Sant Cugat del Valles (Barcelona), Spain Tel: +34-935-65-3131 Mitsubishi Electric Europe B.V. French Branch 25, Boulevard des Bouvets, 92741 Nanterre Cedex, France Tel: +33-1-55-68-55-68 Mitsubishi Electric Europe B.V. Czech Branch Avenir Business Park, Radlicka 751/113e, 158 00 Praha 5, Czech Republic Tel: +420-251-551-470 Mitsubishi Electric Turkey A.S. Umraniye Branch Serifali Mahallesi Nutuk Sokak No:5, TR-34775 Umraniye / Istanbul, Turkey Tel: +90-216-526-3990 Mitsubishi Electric Europe B.V. Polish Branch ul. Krakowska 50, 32-083 Balice, Poland Tel: +48-12-347-65-00 Mitsubishi Electric (Russia) LLC St. Petersburg Branch Piskarevsky pr. 2, bld 2, lit Sch, BC Benua, office 720; RU-195027 St. Petersburg, Russia Tel: +7-812-633-3497

South Africa

China

Taiwan

Korea

Singapore

Thailand

Indonesia

Vietnam

India

Australia

Adroit Technologies 20 Waterford Office Park, 189 Witkoppen Road, Fourways, Johannesburg, South Africa Tel: +27-11-658-8100 Mitsubishi Electric Automation (China) Ltd. No.1386 Hongqiao Road, Mitsubishi Electric Automation Center, Shanghai, China Tel: +86-21-2322-3030 SETSUYO ENTERPRISE CO., LTD. 6F, No.105, Wugong 3rd Road, Wugu District, New Taipei City 24889, Taiwan Tel: +886-2-2299-2499 Mitsubishi Electric Automation Korea Co., Ltd. 7F-9F, Gangseo Hangang Xi-tower A, 401, Yangcheon-ro, Gangseo-Gu, Seoul 07528, Korea Tel: +82-2-3660-9530 Mitsubishi Electric Asia Pte. Ltd. 307 Alexandra Road, Mitsubishi Electric Building, Singapore 159943 Tel: +65-6473-2308 Mitsubishi Electric Factory Automation (Thailand) Co., Ltd. 12th Floor, SV.City Building, Office Tower 1, No. 896/19 and 20 Rama 3 Road, Kwaeng Bangpongpang, Khet Yannawa, Bangkok 10120, Thailand Tel: +66-2682-6522 to 31 PT. Mitsubishi Electric Indonesia Gedung Jaya 11th Floor, JL. MH. Thamrin No.12, Jakarta Pusat 10340, Indonesia Tel: +62-21-3192-6461 Mitsubishi Electric Vietnam Co., LTD. Ho Chi Minh Head Office Unit 01-04, 10th Floor, Vincom Cente

Manualsnet FAQs

If you want to find out how the GOT1000 Mitsubishi works, you can view and download the Mitsubishi GOT1000 1D7M54 RGB Input User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Mitsubishi GOT1000 as well as other Mitsubishi manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Mitsubishi GOT1000. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Mitsubishi GOT1000 1D7M54 RGB Input User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Mitsubishi GOT1000 1D7M54 RGB Input User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Mitsubishi GOT1000 1D7M54 RGB Input User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Mitsubishi GOT1000 1D7M54 RGB Input User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Mitsubishi GOT1000 1D7M54 RGB Input User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.