Summary of Content for Mitsubishi GOT2000 1D7M47 Printer User's Manual PDF
Thank you for choosing Mitsubishi Electric Graphic Operation Terminal (GOT).
2005 MITSUBISHI ELECTRIC CORPORATION
GOT2000/GOT1000 Series Printer Unit
Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.
SAFETY PRECAUTIONS (Always read these precautions before using this equipment.)
Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly. The precautions given in this manual are concerned with this prod- uct. In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".
Note that the CAUTION level may lead to a serious accident according to the circumstances. Always follow the precautions of both levels because they are import- ant to personal safety. Please save this manual to make it accessible when required and always forward it to the end user.
Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.
[STARTUP AND MAINTENANCE PRECAUTIONS]
Do not bundle the control and communication cables with main- circuit, power or other wiring. Run the above cables separately from such wiring and keep them a minimum of 100mm apart. Not doing so noise can cause a malfunction.
Be sure to shut off all phases of the external power supply used by the system before mounting or removing this unit to/from the GOT. Not doing so can cause a unit failure or malfunction.
Before connecting the Bus connection cable to this unit, always shut off GOT power and PLC CPU power externally in all phases. Not doing so can cause a malfunction.
Use this unit in the environment that satisfies the general specifications described in the User's Manual for the GOT used. Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.
When installing this unit to the GOT, fit it to the connection interface of the GOT and tighten the mounting screws in the specified torque range (0.36Nm to 0.48Nm) with a Phillips- head screwdriver No. 2. Undertightening can cause a drop, failure or malfunction. Overtightening can cause a drop, failure or malfunction due to screw or unit damage.
Be sure to shut off all phases of the external power supply used by the system before wiring. Failure to do so may result in an electric shock, product damage or malfunctions.
Exercise care to avoid foreign matter such as chips and wire offcuts entering the unit. Not doing so can cause a fire, failure or malfunction.
Make sure to securely connect the cable to the connector of unit. Incorrect connection may cause malfunctions.
Before starting cleaning or mounting screw retightening, always shut off GOT power externally in all phases. Not doing so can cause a unit failure or malfunction. Tighten the mounting screws in the specified torquerange (0.36Nm to 0.48Nm) with a Phillips-head screwdriver No. 2. Undertightening can cause the GOT to drop, short circuit or malfunction. Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or unit.
The following shows manuals relevant to this product.
For detailed manuals and relevant manuals, refer to the e-Manual or PDF manuals stored in the DVD-ROM for the screen design software used.
The latest manuals are also available from MITSUBISHI ELECTRIC FA Global Website (www.MitsubishiElectric.com/fa).
Do not disassemble or modify the unit. Doing so can cause a failure, malfunction, injury or fire.
Do not touch the conductive and electronic parts of this unit directly. Doing so can cause a unit malfunction or failure.
The cables connected to the unit must be run in ducts or clamped. Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidentalpulling of the cables or can cause a malfunction due to a cable connection fault.
When unplugging the cable connected to the unit, do not hold and pull from the cable portion. Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cableconnection fault.
Do not drop the module or subject it to strong shock. A module damage may result.
Before touching the unit, always touch grounded metals, etc. to discharge static electricity from human body, etc. Not doing so can cause the unit to failure or malfunction.
When disposing of this product, treat it as industrial waste.
Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the User's Manual for the GOT used, as they are precision devices. Failure to do so may cause the unit to fail. Check if the unit operates correctly after transportation.
When fumigants that contain halogen materials such as fluorine, chlorine, bromine, and iodine are used for disinfecting and protecting wooden packaging from insects, they cause malfunction when entering our products. Please take necessary precautions to ensure that remaining materials from fumigant do not enter our products, or treat packaging with methods other than fumigation (heat method). Additionally, disinfect and protect wood from insects before packing products.
Manual name Manual number
(Model code) GOT2000 Series Users Manual (Hardware) (Sold separately)
GOT2000 Series Connection Manual (Microcomputers, MODBUS/Fieldbus Products, Peripherals)
GT16 User's Manual (Hardware) (Sold separately)
GT15 User's Manual (Sold separately)
GOT1000 Series Connection Manual (Microcomputer, MODBUS Products, Peripherals) for GT Works3
Compliance with the EMC and Low Voltage Directives To configure a system meeting the requirements of the EMC and Low Voltage Directives when incorporating the Mitsubishi GOT (EMC and Low Voltage Directives compliant) into other machinery or equipment, refer to "EMC AND LOW VOLTAGE DIRECTIVES" of the General Description included with the GOT used. The CE mark, indicating compliance with the EMC and Low Voltage Directives, is printed on the rating plate of the GOT.
Compliance with the new China RoHS directive GOT
SJ/T11364 : GB/T26572
Referenced Standard: GB/T15969.2 (Requirement of Chinese standardized law)
Packing List The following items are included.
This user's manual describes the GOT2000/GOT1000 series printer unit (hereinafter referred to as the printer unit). With the printer unit installed, the GOT can be connected to a printer. Refer to the Users Manual for the GOT used for the applicable GOT. Use PictBridge compatible printers. Printers incompatible with PictBridge cannot be used with the GOT.
The performance specifications of the printer unit are indicated below. The general specifications of the printer unit are the same as those of the GOT. Refer to the Users Manual for the GOT used for the general specifications of the GOT.
Note: This symbol mark is for China only.
Model Product Quantity
Printer unit 1
Mounting screw set (2 pieces of screw, 2 pieces of sticker)
Cable clamp set (Connector holder with screw, cable clamp)
GOT2000/GOT1000 Series Printer Unit User's Manual (This manual)
Dedicated printer connection cable (3m) 1
Internal current consumption (5VDC)
Weight 0.08kg (0.18lb) (Including connector
holder and cable clamp)
3. PART NAMES AND EXTERNAL DIMENSIONS
* The external dimensions of printer unit with a cable clamp and connector holder attached is shown above.
Dimensions of X when the printer unit is mounted to the GOT
4. INSTALLATION AND REMOVAL PROCEDURE
4.1 Cable Connection (1) Connect a dedicated printer connection cable to the printer unit.
(2) Attach the accessory connector holder to the dedicated printer connection cable and tighten the screw of connector holder with tightening torque of 0.36Nm to 0.48Nm.
(3) Depending on the use environment such as when fastening cable is difficult, attach a cable clamp to the printer unit. Attach the cable clamp to the printer unit. Position the cable clamp band outside, and insert the cable clamp to section A shown in the following figure until it clicks. For the band inserting direction, refer to the arrow.
GOT GT27 GT25 GT16 GT15
15" 23 (0.91) - 19.5 (0.77) 21 (0.83)
12.1" 23 (0.91) 23 (0.91) 18 (0.71) 18 (0.71)
10.4" 23 (0.91) 23 (0.91) 21 (0.83) 21 (0.83)
8.4" 23 (0.91) 23 (0.91) 23 (0.91) 23 (0.91)
5.7" 23 (0.91) - 23 (0.91) 23 (0.91)
No. Name Description
1) Mounting screw Mounting screws fixed with the front communication unit or GOT
2) Connector holder Holder for preventing a dedicated printer connection cable disconnection
3) Cable clamp For cable treatment
4) Connector USB connector for connecting a dedicated printer connection cable
5) Rating plate -
GOT main unit
Unit: mm (inch)
Dedicated printer connection cable
(The cable clamp is the RSG-130-V0 of KITAGAWA INDUSTRIES CO.,LTD. or equivalent.)
(4) Insert the dedicated printer connection cable in the looped cable clamp band and pull the band to fasten the cable.
4.2 Unit Installation
The installation procedure for the printer unit is explained using the GT1575.
(1) Power off the GOT.
(2) Remove one extension unit cover of the GOT.
(3) Fit the printer unit in the GOT case.
(4) Fasten the printer unit by tightening its mounting screws (2 places) with tightening torque 0.36Nm to 0.48Nm.
Cable to be used When connecting the printer to the GOT, use the supplied dedicated printer connection cable (USB cable).
Screw of the connector holder Do not remove the screw attached to the connector holder. In the case the screw is removed, do not use any other screws. Doing so may damage the unit.
In the case a cable clamp is attached
In the case a cable clamp is attached
(5) When mounting any communication unit on the outer stage, refer to the User's Manual for the GOT used. When not mounting any communication unit on the outer layer, stick accessory stickers on the top of mounting screws (2 places) to cover the top of them in order to avoid receiving electrostatic. Keep the connector cover and sticker (see the following figure) fixed.
4.3 Unit Removal
For removing the printer unit, reverse the procedure of the installation.
Precautions for connecting the printer Any printer cannot be connected to GOT via USB hub. Wait 5s or more between the connection and disconnection of
the dedicated printer connection cable. If connecting or disconnecting the dedicated printer connection cable shortly after disconnecting or connecting the cable, the GOT may not operate normally.
Do not connect or disconnect the dedicated printer connection cable during printing. Doing so can cause the GOT operate incorrectly.
Connected printer may not be recognized in rare cases. When printer is not recognized, disconnect the dedicated printer connection cable once and connect it again.
When the printer has been connected to a personal computer and used before it is connected to GOT, power on the printer again and connect it to GOT.
Do not connect any devices to the printer while GOT is connected to it.
Do not connect any devices other than printer to the printer unit.
(1) Pulling out the cable clamp band The cable clamp band can be pulled out after cable treatment. Pull out the band with pressing the tab of the cable clamp outward using a screwdriver etc.
(2) Removing from the printer unit The dedicated printer connection cable can be removed from the unit with the cable clamp attached. Remove the cable clamp by pressing it in both directions (arrow A).
Warranty Mitsubishi Electric will not be held liable for damage caused by factors found not to be the cause of Mitsubishi Electric; machine damage or lost profits caused by faults in the Mitsubishi Electric products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi Electric; damages to products other than Mitsubishi Electric products; and to other duties.
For safe use This product has been manufactured as a general-purpose part for
general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.
Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi Electric.
This product has been manufactured under strict quality control. However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.
Country/Region Sales office/Tel
USA Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A. Tel: +1-847-478-2100
Brazil Mitsubishi Electric do Brasil Comercio e Servicos Ltda. Avenida Adelino Cardana, 293, 21 andar, Bethaville, Barueri SP, Brazil Tel: +55-11-4689-3000
Mexico Mitsubishi Electric Automation, Inc. Mexico Branch Boulevard Miguel de Cervantes Saavedra 301, Torre Norte Piso 5, Ampliacion Granada, Miguel Hidalgo, Ciudad de Mexico, Mexico, C.P.11520 Tel: +52-55-3067-7512
Germany Mitsubishi Electric Europe B.V. German Branch Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany Tel: +49-2102-486-0
UK Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, UK-Hatfield, Hertfordshire, AL10 8XB, U.K. Tel: +44-1707-28-8780
Italy Mitsubishi Electric Europe B.V. Italian Branch Centro Direzionale Colleoni - Palazzo Sirio, Viale Colleoni 7, 20864 Agrate Brianza (MB), Italy Tel: +39-039-60531
Spain Mitsubishi Electric Europe B.V. Spanish Branch Carretera de Rubi, 76-80-Apdo. 420, E-08190 Sant Cugat del Valles (Barcelona), Spain Tel: +34-935-65-3131
France Mitsubishi Electric Europe B.V. French Branch 25, Boulevard des Bouvets, 92741 Nanterre Cedex, France Tel: +33-1-55-68-55-68
Czech Mitsubishi Electric Europe B.V. Czech Branch Pekarska 621/7, 155 00 Praha 5, Czech Republic Tel: +420-255 719 200
Turkey Mitsubishi Electric Turkey A.S. Umraniye Branch Serifali Mahallesi Nutuk Sokak No:5, TR-34775 Umraniye / Istanbul, Turkey Tel: +90-216-526-3990
Poland Mitsubishi Electric Europe B.V. Polish Branch ul. Krakowska 48, 32-083 Balice, Poland Tel: +48-12-347-65-00
Russia Mitsubishi Electric (Russia) LLC St. Petersburg Branch Piskarevsky pr. 2, bld 2, lit "Sch", BC "Benua", office 720; 195027 St. Petersburg, Russia Tel: +7-812-633-3497
South Africa Adroit Technologies 20 Waterford Office Park, 189 Witkoppen Road, Fourways, South Africa Tel: +27-11-658-8100
China Mitsubishi Electric Automation (China) Ltd. Mitsubishi Electric Automation Center, No.1386 Hongqiao Road, Shanghai, China Tel: +86-21-2322-3030
Taiwan SETSUYO ENTERPRISE CO., LTD. 6F, No.105, Wugong 3rd Road, Wugu District, New Taipei City 24889, Taiwan Tel: +886-2-2299-2499
Korea Mitsubishi Electric Automation Korea Co., Ltd. 7F to 9F, Gangseo Hangang Xi-tower A, 401, Yangcheon-ro, Gangseo-Gu, Seoul 07528, Korea Tel: +82-2-3660-9569
Singapore Mitsubishi Electric Asia Pte. Ltd. 307 Alexandra Road, Mitsubishi Electric Building, Singapore 159943 Tel: +65-6473-2308
Thailand Mitsubishi Electric Factory Automation (Thailand) Co., Ltd. 12th Floor, SV.City Building, Office Tower 1, No. 896/19 and 20 Rama 3 Road, Kwaeng Bangpongpang, Khet Yannawa, Bangkok 10120, Thailand Tel: +66-2682-6522 to 31
Indonesia PT. Mitsubishi Electric Indonesia Gedung Jaya 8th Floor, JL. MH. Thamrin No.12, Jakarta Pusat 10340, Indonesia Tel: +62-21 3192-6461
Vietnam Mitsubishi Electric Vietnam Company Limited 11th & 12th Floor, Viettel Tower B, 285 Cach Mang Thang 8 Street, Ward 12, District 10, Ho Chi Minh City, Vietnam. Tel: +84-28-3910-5945
India Mitsubishi Electric India Pvt. Ltd. Pune Branch Emerald House, EL-3, J Block, M.I.D.C., Bhosari, Pune - 411026, Maharashtra, India Tel: +91-20-2710-2000
Australia MITSUBISHI ELECTRIC AUSTRALIA PTY. LTD. 348 Victoria Road, P.O. Box 11, Rydalmere, N.S.W 2116, Australia Tel: +61-2-9684-7777
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN
When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.
Specifications subject to change without notice. Printed in Japan, November 2021.
If you want to find out how the GOT2000 Mitsubishi works, you can view and download the Mitsubishi GOT2000 1D7M47 Printer User's Manual on the Manualsnet website.
Yes, we have the User's Manual for Mitsubishi GOT2000 as well as other Mitsubishi manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The User's Manual should include all the details that are needed to use a Mitsubishi GOT2000. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Mitsubishi GOT2000 1D7M47 Printer User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Mitsubishi GOT2000 1D7M47 Printer User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Mitsubishi GOT2000 1D7M47 Printer User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Mitsubishi GOT2000 1D7M47 Printer User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Mitsubishi GOT2000 1D7M47 Printer User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.