Mitsubishi GOT2000 GT25-FNADP-U-JE Ethernet User's Manual PDF

User's Manual

GT25-FNADP

Thank you for choosing Mitsubishi Electric Graphic Operation Terminal (GOT).

2015 MITSUBISHI ELECTRIC CORPORATION

GOT2000 Series Field Network Adapter Unit

Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.

MODEL GT25-FNADP-U-JE

MODEL CODE

1D7MQ2

IB(NA)-0800549-D(1806)MEE

SAFETY PRECAUTIONS (Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals intro- duced in this manual carefully and pay full attention to safety to handle the product correctly. The precautions given in this manual are concerned with this product. In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".

Note that the CAUTION level may lead to a serious accident according to the circumstances. Always follow the precautions of both levels because they are important to per- sonal safety. Please save this manual to make it accessible when required and always forward it to the end user.

[DESIGN PRECAUTIONS]

Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.

If a communication fails in data link, the faulty station holds the data link data generated before the communication error. Create an interlock circuit in the sequence program using the communication status information in order that the system will operate safely. Failure to do so may cause mis-outputs or malfunctions, resulting in accidents. Check the faulty station and the operation status during communication error by referring to the relevant manuals.

Some failures of cable or communication unit may cause the GOT to keep the outputs on or off. Create an external circuit for monitoring output signals that may lead to serious accidents. Failure to do so may cause mis-outputs or malfunctions, resulting in accidents.

WARNING

CAUTION

WARNING

[DESIGN PRECAUTIONS]

[INSTALLATION PRECAUTIONS]

[WIRING PRECAUTIONS]

[STARTUP AND MAINTENANCE PRECAUTIONS]

If a communication error (including cable disconnection) occurs during monitoring, the communication between the GOT and programmable controller CPU may be interrupted and the GOT may be inoperative. For bus connection : The programmable controller CPU is down and the GOT is inoperative. For other than above: The GOT is inoperative. When configuring a system including the GOT, the possibility of GOT communication error must be considered; make sure the operation significant for the system will be performed by switches on devices other than the GOT. Failure to do so may cause mis-outputs or malfunctions, resulting in accidents.

Do not bunch the control wires or communication cables with the main circuit or power wires, or lay them close to each other. As a guide, separate the lines by a distance of at least 100mm (3.94 inches) otherwise malfunctions may occur due to noise.

Be sure to shut off all phases of the external power supply used by the system before mounting or removing this unit to/from the GOT. Not doing so can cause a unit failure or malfunction.

Before connecting the Bus connection cable to this unit, always shut off GOT power and PLC CPU power externally in all phases.Not doing so can cause a malfunction.

Use this unit in the environment that satisfies the general specifications described in the User's Manual for the GOT used. Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

Do not drop the unit or subject it to string shock. A unit damage may result.

When mounting this unit on the GOT, fit it to the connection interface of the GOT, and tighten the mounting screws in the specified torque range (0.36Nm to 0.48Nm) with a Phillips-head screwdriver No. 2. Undertightening can cause a drop, failure or malfunction. Overtightening can cause a drop, failure or malfunction due to screw or unit damage.

No extension unit can be mounted on the field network adapter unit. To mount multiple extension units, mount the field network adapter unit on top of them.

Install a communication module before mounting the field network adapter unit on the GOT. Remove the communication module after removing the field network adapter unit from the GOT.

When installing a communication module, do not directly touch the circuit board of the field network adapter unit.

Do not remove hexalobular socket screws from the communication module. Removing the screws unfixes the front face panel of the communication module, and the communication module cannot be smoothly pulled out from the field network adapter unit.

Push the communication module straight into the unit, aligning it with the guides. Not doing so may cause the pins in the field network adapter unit to bend.

Be sure to shut off all phases of the external power supply used by the system before wiring. Failure to do so may result in an electric shock, product damage or malfunctions.

Exercise care to avoid foreign matter such as chips and wire offcuts entering the unit. Not doing so can cause a fire, failure or malfunction.

Make sure to securely connect the cable to the connector of unit. Incorrect connection may cause malfunctions.

Before starting cleaning, always shut off GOT power externally in all phases. Not doing so can cause a unit failure or malfunction. Undertightening can cause the GOT to drop, short circuit or malfunction. Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

Do not disassemble or modify the unit and the CF card. Doing so can cause a failure, malfunction, injury or fire.

WARNING

CAUTION

WARNING

CAUTION

WARNING

CAUTION

WARNING

[DISPOSAL PRECAUTIONS]

[TRANSPORTATION PRECAUTIONS]

Manual

The following shows manuals relevant to this product.

For detailed manuals and relevant manuals, refer to the e-Manual or PDF manuals stored in the DVD-ROM for the screen design software used.

The latest manuals are also available from MITSUBISHI ELECTRIC FA Global Website (http://www.mitsubishielectric.com/fa/).

Compliance with the EMC and Low Voltage Directives To configure a system meeting the requirements of the EMC and Low Voltage Directives when incorporating the Mitsubishi GOT (EMC and Low Voltage Directives compliant) into other machinery or equipment, refer to "EMC AND LOW VOLTAGE DIRECTIVES" of the General Description included with the GOT used. The CE mark, indicating compliance with the EMC and Low Voltage Directives, is printed on the rating plate of the GOT.

Compliance with the new China RoHS directive GOT

6 6

SJ/T11364

Do not touch the conductive areas and electronic parts of this unit directly. Doing so can cause a unit malfunction or failure.

Always secure the cables connected to the unit, e.g. run them in conduits or clamp them. Not doing so can cause unit or cable damage due to dangling, moved or accidentally pulled cables or can cause a malfunction due to a cable contact fault.

Do not hold the cable part when unplugging any cable connected to the unit. Doing so can cause unit or cable damage or a malfunction due to a cable contact fault.

Always make sure to touch the grounded metal to discharge the electricity charged in the body, etc., before touching the unit. Failure to do so may cause a failure or malfunctions of the unit.

Dispose of this product as industrial waste.

Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the User's Manual for the GOT used, as they are precision devices. Failure to do so may cause the unit to fail. Check if the unit operates correctly after transportation.

When fumigants that contain halogen materials such as fluorine, chlorine, bromine, and iodine are used for disinfecting and protecting wooden packaging from insects, they cause malfunction when entering our products. Please take necessary precautions to ensure that remaining materials from fumigant do not enter our products, or treat packaging with methods other than fumigation (heat method). Additionally, disinfect and protect wood from insects before packing products.

Manual name Manual number

(Model code)

GOT2000 Series User's Manual (Hardware) (Sold separately)

SH-081194ENG (1D7MJ5)

GOT2000 Series Connection Manual (Microcomputers, MODBUS/Fieldbus Products, Peripherals) For GT Works3 Version1

SH-081200ENG

Note: This symbol mark is for China only.

Pb

Hg

Cd

Cr(VI)

PBB

PBDE

CAUTION

CAUTION

CAUTION

: GB/T26572

: GB/T26572

Referenced Standard: GB/T15969.2 (Requirement of Chinese standardized law)

Packing List After unpacking the box, check that the following products are included.

1. OVERVIEW This user's manual describes the GT25-FNADP field network adapter unit (hereinafter referred to as the field network adapter unit). The field network adapter unit can be used with the following field networks by using the Anybus CompactCom M40 network communication module manufactured by HMS (hereinafter referred to as the communication module).

:*1: When purchasing a communication module, specify an article number and tell HMS or the distributor from which you purchase the module.

Prepare communication modules and cables by users.

2. SPECIFICATIONS The following shows the performance specifications of the field network adapter unit. The general specifications of the field network adapter unit are the same as those of the GOT. For the general specifications of the GOT, refer to the GOT2000 Series User's Manual (Hardware).

3. PART NAMES AND EXTERNAL DIMENSIONS

Model Product Quantity

GT25-FNADP

Field network adapter unit 1

Screw set (Two P-type pan head screws with SWPW, M312)

1

GOT2000 Series Field Network Adapter Unit User's Manual (This manual)

1

Communication module product name

Communication module article number*1

Supported network

ABCC-M40-DPV1 AB6910-B, AB6910-C PROFIBUS DP

ABCC-M40-DEV AB6909-B, AB6909-C DeviceNet

Item Specifications Internal current consumption 5.0 VDC 0.40 A Weight 0.07 kg

No. Name Description

1) Mounting screw Screw for fixing the GOT

2) Rating plate -

3) Connector for the communication module

Connector for connecting a communication module

4) Extension connector Extension connector connected to the GOT

63 (2.48) 1)

3)

2)

1)

4)

1 (0.04)2.5 (0.10)

10 5

(4 .1

3) 32

( 1.

26 )

Communication module

24.7 (0.97)

24.1 (0.95)

GOT main unit

Unit : mm (inch)

4. INSTALLATION AND REMOVAL PROCEDURE

4.1 Installation

4.1.1 Installing the communication module to the field network adapter unit

The installation procedure for the communication module is explained using the communication module ABCC-M40-DPV1.

1) Place the field network adapter unit on a flat surface such as a table. Align the grooves on the sides of the communication module with the guide on the circuit board of the field network adapter unit, and insert the communication module into the field network adapter unit.

2) Push the communication module straight in the insertion direction into the field network adapter unit while pushing the whole communication module down from above.

The communication module reaches the connector for communication modules at the position where the distance between the front face panel of the communication module and the field network adapter unit is approximately 4 mm. When installing the communication module, be careful not to damage the connector for communication modules.

Turn the field network adapter unit upside down to check the fixing hooks. Check that the fixing hooks on the communication module are within the white lines of the circuit board of the field network adapter unit (A in the figure below).

Point

Precautions for installation and removal of the communication module No extension unit can be mounted on the field network adapter unit.

To mount multiple extension units, mount the field network adapter unit on top of them.

Install a communication module before mounting the field network adapter unit on the GOT. Remove the communication module after removing the field network adapter unit from the GOT.

When installing a communication module, do not directly touch the circuit board of the field network adapter unit.

Do not remove hexalobular socket screws from the communication module. Removing the screws unfixes the front face panel of the communication module, and the communication module cannot be smoothly pulled out from the field network adapter unit.

Push the communication module straight into the unit, aligning it with the guides. Not doing so may cause the pins in the field network adapter unit to bend.

Groove

Guide

Field network adapter unit

Communication module

Install the module on a flat surface such as a table.

4 mm or so

Front face panel

Push the module straight into the unit while pushing down the whole module from above.

A

Fixing hooks

White lines

3) Tighten two hexalobular socket screws (T8) for fixing the communication module with a torque of 0.25 Nm

Turn the field network adapter unit upside down to check the fixing mechanism. Tightening the hexalobular socket screws pushes up the fixing mechanism of the communication module and fixes the communication module to the board of the field network adapter unit.

4.1.2 Mounting the field network adapter unit on the GOT

The mounting procedure for the field network adapter unit is explained using the GT2712.

1) Turn off the GOT. 2) Pull up the one hook in the extension unit cover (One cover on the left in the

figure below) of the GOT to remove the cover toward the opposite side of the hook of the cover as a fulcrum.

3) Connect the field network adapter unit to the extension interface on the GOT. Then, tighten 2 mounting screws (M3 12) with a torque of 0.36 Nm to 0.48 Nm to fix the unit.

Hexalobular socket screws

Fixing mechanism

Before tightening

After tightening The fixing

mechanism is lifted up.

4.2 Removal

4.2.1 Removing the field network adapter unit from the GOT

Remove the field network adapter unit in the reverse procedure to the mounting.

4.2.2 Removing the communication module from the field network adapter unit

Remove the communication module in the reverse procedure to the installation.

1) Loosen the two hexalobular socket screws (T8) for fixing the communication module from the front face panel for 5 mm or so.

Turn the field network adapter unit upside down to check the fixing mechanism. Loosen the two hexalobular socket screws until the fixing mechanism is released.

2) Pull out the communication module while holding the field network adapter unit with one hand.

MELSEC, MELSOFT, and GOT, are trademarks or registered trademarks of Mitsubishi Electric Corporation in Japan and other countries. Anybus is a registered trademark of HMS Industrial Networks AB. DeviceNet is a trademark of ODVA (Open DeviceNet Vendor Association, Inc.). Other company and product names herein are trademarks or registered trademarks of their respective owners.

Front face panel

5 mm or so

Fixing mechanism

Released

Fixed

Front face panel

Warranty Mitsubishi Electric will not be held liable for damage caused by factors found not to be the cause of Mitsubishi Electric; machine damage or lost profits caused by faults in the Mitsubishi Electric products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi Electric; damages to products other than Mitsubishi Electric products; and to other duties.

For safe use This product has been manufactured as a general-purpose part for

general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.

Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi Electric.

This product has been manufactured under strict quality control. However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.

USA

Brazil

Mexico

Germany

UK

Italy

Spain

France

Czech

Turkey

Poland

Russia

South Africa

China

Taiwan

Korea

Singapore

Thailand

Indonesia

Vietnam

India

Australia

Country/Region Sales office/Tel Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A. Tel: +1-847-478-2100 Mitsubishi Electric do Brasil Comercio e Servicos Ltda. Avenida Adelino Cardana, 293, 21 andar, Bethaville, Barueri SP, Brasil CEP 06401-147 Tel: +55-11-4689-3000 Mitsubishi Electric Automation, Inc. Mexico Branch Mariano Escobedo #69, Col. Zona Industrial, Tlalnepantla Edo. Mexico, C.P.54030 Tel: +52-55-3067-7511 Mitsubishi Electric Europe B.V. German Branch Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany Tel: +49-2102-486-0 Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Hertfordshire, AL10 8XB, U.K. Tel: +44-1707-28-8780 Mitsubishi Electric Europe B.V. Italian Branch Centro Direzionale Colleoni - Palazzo Sirio, Viale Colleoni 7, Agrate Brianza (MB), Italy Tel: +39-039-60531 Mitsubishi Electric Europe B.V. Spanish Branch Carretera de Rubi 76-80-Apdo.420, 08190 Sant Cugat del Valles (Barcelona), Spain Tel: +34-935-65-3131 Mitsubishi Electric Europe B.V. French Branch 25, Boulevard des Bouvets, 92741 Nanterre Cedex, France Tel: +33-1-55-68-55-68 Mitsubishi Electric Europe B.V. Czech Branch Avenir Business Park, Radlicka 751/113e, 158 00 Praha 5, Czech Republic Tel: +420-251-551-470 Mitsubishi Electric Turkey A.S. Umraniye Branch Serifali Mahallesi Nutuk Sokak No:5, TR-34775 Umraniye / Istanbul, Turkey Tel: +90-216-526-3990 Mitsubishi Electric Europe B.V. Polish Branch ul. Krakowska 50, 32-083 Balice, Poland Tel: +48-12-347-65-00 Mitsubishi Electric (Russia) LLC St. Petersburg Branch Piskarevsky pr. 2, bld 2, lit Sch, BC Benua, office 720; RU-195027 St. Petersburg, Russia Tel: +7-812-633-3497 Adroit Technologies 20 Waterford Office Park, 189 Witkoppen Road, Fourways, Johannesburg, South Africa Tel: +27-11-658-8100 Mitsubishi Electric Automation (China) Ltd. No.1386 Hongqiao Road, Mitsubishi Electric Automation Center, Shanghai, China Tel: +86-21-2322-3030 SETSUYO ENTERPRISE CO., LTD. 6F, No.105, Wugong 3rd Road, Wugu District, New Taipei City 24889, Taiwan Tel: +886-2-2299-2499 Mitsubishi Electric Automation Korea Co., Ltd. 7F-9F, Gangseo Hangang Xi-tower A, 401, Yangcheon-ro, Gangseo-Gu, Seoul 07528, Korea Tel: +82-2-3660-9530 Mitsubishi Electric Asia Pte. Ltd. 307 Alexandra Road, Mitsubishi Electric Building, Singapore 159943 Tel: +65-6473-2308 Mitsubishi Electric Factory Automation (Thailand) Co., Ltd. 12th Floor, SV.City Building, Office Tower 1, No. 896/19 and 20 Rama 3 Road, Kwaeng Bangpongpang, Khet Yannawa, Bangkok 10120, Thailand Tel: +66-2682-6522 to 31 PT. Mitsubishi Electric Indonesia Gedung Jaya 11th Floor, JL. MH. Thamrin No.12, Jakarta Pusat 10340, Indonesia Tel: +62-21-3192-6461 Mitsubishi Electric Vietnam Co., LTD. Ho Chi Minh Head Office Unit 01-04, 10th Floor, Vincom Center, 72 Le Thanh Ton Street, District 1, Ho Chi Minh City, Vietnam Tel: +84-8-3910-5945 Mitsubishi Electric India Pvt. Ltd. Pune Branch Emerald House, EL -3, J Block, M.I.D.C., Bhosari, Pune - 411026, Maharashtra, India Tel: +91-20-2710-2000 Mitsubishi Electric Australia Pty. Ltd. 348 Victoria Road, P.O. Box 11, Rydalmere, N.S.W. 2116, Australia Tel: +61-2-9684-7777

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI,