Mitsubishi GOT1000 GT15-J71GP23-SX Controller User's Manual PDF

User's Manual GT15-J71GP23-SX

Thank you for choosing Mitsubishi Electric Graphic Operation Terminal (GOT).

GOT2000/GOT1000 Series CC-Link IE Controller Network

Communication Unit

Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.

MODEL GT15-J71GP23-SX-U MODEL CODE 1D7M76

IB(NA)-0800412-J(2011)MEE

SAFETY PRECAUTIONS (Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly. The precautions given in this manual are concerned with this product. In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".

Note that the CAUTION level may lead to a serious accident according to the circumstances. Always follow the precautions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.

WARNING

CAUTION

A-1

[DESIGN PRECAUTIONS]

If a communication fails in data link, the faulty station holds the data link data generated before the communication error. Create an interlock circuit in the sequence program using the communication status information in order that the system will operate safely. Failure to do so may cause mis-outputs or malfunctions, resulting in accidents. Check the faulty station and the operation status during communication error by referring to the relevant manuals.

Some failures of cable or communication unit may cause the GOT to keep the outputs on or off. Create an external circuit for monitoring output signals that may lead to serious accidents. Failure to do so may cause mis-outputs or malfunctions, resulting in accidents.

If a communication error (including cable disconnection) occurs during monitoring, the communication between the GOT and programmable controller CPU may be interrupted and the GOT may be inoperative.

For bus connection : The programmable controller CPU is down and the GOT is inoperative.

For other than above: The GOT is inoperative. When configuring a system including the GOT, the possibility of GOT communication error must be considered; make sure the operation significant for the system will be performed by switches on devices other than the GOT. Failure to do so may cause mis-outputs or malfunctions, resulting in accidents.

Laser diodes are used in optical transceivers for the CC-Link IE Controller Network. The class of these laser diodes is Class 1.

WARNING

A-2

[DESIGN PRECAUTIONS]

[INSTALLATION PRECAUTIONS]

To maintain the security (confidentiality, integrity, and availability) of the GOT and the system against unauthorized access, DoS*1 attacks, computer viruses, and other cyberattacks from unreliable networks and devices via network, take appropriate measures such as firewalls, virtual private networks (VPNs), and antivirus solutions. Mitsubishi Electric shall have no responsibility or liability for any problems involving GOT trouble and system trouble by unauthorized access, DoS attacks, computer viruses, and other cyberattacks. *1 DoS: A denial-of-service (DoS) attack disrupts services by overloading systems or exploiting vulnerabilities, resulting in a denial-of-service (DoS) state.

Do not bunch the control wires or communication cables with the main circuit or power wires, or lay them close to each other. As a guide, separate the lines by a distance of at least 100mm (3.94 inches) otherwise malfunctions may occur due to noise.

Be sure to shut off all phases of the external power supply used by the system before mounting or removing this unit to/from the GOT. Not doing so can cause a unit failure or malfunction.

Use this unit in the environment that satisfies the general specifications described in the User's Manual for the GOT used. Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

When installing this unit to the GOT, fit it to the connection interface of the GOT and tighten the mounting screws in the specified torque range (0.36 Nm to 0.48 Nm) with a Phillips-head screwdriver No.2. Undertightening can cause a drop, failure or malfunction. Overtightening can cause a drop, failure or malfunction due to screw or unit damage.

WARNING

CAUTION

WARNING

CAUTION

A-3

[INSTALLATION PRECAUTIONS]

[WIRING PRECAUTIONS]

[STARTUP AND MAINTENANCE PRECAUTIONS]

Do not directory touch the conductive part or electronic components of the unit. This may cause the unit to fail or malfunction.

Be sure to shut off all phases of the external power supply used by the system before wiring. Failure to do so may cause electric shock, product damage or malfunctions.

Be careful not to let foreign matter such as dust or wire chips get inside the unit. This may cause a fire, failure or malfunctions.

Make sure to securely connect the cable to the connector of unit. Incorrect connection may cause malfunctions.

Make sure to fix communication cables and power cables to the unit by ducts or clamps. Failure to do so may cause damage of the unit or the cables due to accidental pull or unintentional shifting of the cables, or malfunctions due to poor contact of the cables.

Do not hold the cable by hand and pull it out from the unit. When removing the cable from the unit, make sure to hold the connector by hand and pull it. Failure to do so may cause malfunctions or damage to the unit or cable.

Do not touch the connector while power is on. Failure to do so may cause electric shock or malfunctions.

Before starting cleaning, always shut off GOT power externally in all phases. Not doing so can cause a unit failure or malfunction.

CAUTION

WARNING

CAUTION

WARNING

A-4

[STARTUP AND MAINTENANCE PRECAUTIONS]

[DISPOSAL PRECAUTIONS]

[TRANSPORTATION PRECAUTIONS]

Do not disassemble or modify any unit. This will cause failure, malfunction, injuries, or fire.

Do not touch the conductive areas and electronic parts of this unit directly. Doing so can cause a unit malfunction or failure.

Make sure to externally shut off all phases of the power supply before cleaning the unit and retightening unit mounting screws. Failure to do so may cause the unit to fail or malfunction. Loose tightening may cause a fall of the unit, short circuits, or malfunctions. Overtightening may damage the screws and/or the unit, resulting in a fall of the unit, short circuits or malfunctions.

Make sure to touch the grounded metal to discharge the electricity charged in the body, etc., before touching the unit. Failure to do so may cause a failure or malfunctions of the unit.

Dispose of this product as industrial waste.

Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of Use this unit in the environment that satisfies the general specifications described in the User's Manual for the GOT used, as they are precision devices. Failure to do so may cause the unit to fail. Check if the unit operates correctly after transportation.

When fumigants that contain halogen materials such as fluorine, chlorine, bromine, and iodine are used for disinfecting and protecting wooden packaging from insects, they cause malfunction when entering our products.Please take necessary precautions to ensure that remaining materials from fumigant do not enter our products, or treat packaging with methods other than fumigation (heat method).Additionally, disinfect and protect wood from insects before packing products.

CAUTION

CAUTION

CAUTION

A-5

REVISIONS * The manual number is noted at the lower right of the top cover.

2008 MITSUBISHI ELECTRIC CORPORATION

Print Date *Manual Number Revision

Jan., 2008 IB(NA)-0800412-A First edition

Jan., 2009 IB(NA)-0800412-B Patial addition Chapter 1, 2, 4, 7

Jun., 2009 IB(NA)-0800412-C Partial corrections Compliance with the EMC and Low Voltage Directives

Jun., 2011 IB(NA)-0800412-D Partial corrections Chapter 7 Patial addition Compliance with the Radio Waves Act (South Korea)

Oct., 2014 IB(NA)-0800412-E Partial corrections SAFETY PRECAUTIONS Chapter 4, 7

May, 2014 IB(NA)-0800412-F Partial corrections Cover

Oct., 2016 IB(NA)-0800412-G Partial corrections Compliance with the RoHS

Apr., 2017 IB(NA)-0800412-H Partial corrections Cover

Jun., 2018 IB(NA)-0800412-I Patial addition Compliance with Chinese standardized law

Nov., 2020 IB(NA)-0800412-J Partial corrections SAFETY PRECAUTIONS

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.

A-6

A-7

CONTENTS

1. OVERVIEW ................................................................................................... 1 2. SPECIFICATIONS ......................................................................................... 1 3. PART NAMES ............................................................................................... 3 4. INSTALLATION PROCEDURE ..................................................................... 6 5. PRECAUTIONS FOR WIRING CABLES ....................................................... 8 6. WIRING METHOD ......................................................................................... 9 7. EXTERNAL DIMENSIONS .......................................................................... 10

Compliance with the EMC and Low Voltage Directives To configure a system meeting the requirements of the EMC and Low Voltage Directives when incorporating the Mitsubishi GOT (EMC and Low Voltage Directives compliant) into other machinery or equipment, refer to "EMC AND LOW VOLTAGE DIRECTIVES" of the General Description included with the GOT used. The CE mark, indicating compliance with the EMC and Low Voltage Directives, is printed on the rating plate of the GOT.

Manual The following shows manuals relevant to this product.

For relevant manuals, refer to the PDF manuals stored in the DVD-ROM for the drawing software used.

Detailed Manual

Manual name Manual number (Model code)

GOT2000 Series User's Manual (Hardware) (Sold separately)

SH-081194ENG (1D7MJ5)

GOT2000 Series Connection Manual (Mitsubishi Products) For GT Works3 Version1

(Sold separately)

SH-081197ENG (1D7MJ8)

GT16 User's Manual (Hardware) (Sold separately)

SH-080928ENG (1D7MD3)

GT15 User's Manual (Sold separately)

SH-080528ENG (1D7M23)

GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3

(Sold separately)

SH-080868ENG (1D7MC2)

Relevant Manuals

A-8

Compliance with the new China RoHS directive GOT

6 6

SJ/T11364 : GB/T26572

: GB/T26572

Referenced Standard: GB/T15969.2 (Requirement of Chinese standardized law)

Packing List The following items are included.

Note: This symbol mark is for China only.

Pb

Hg

Cd

Cr(VI)

PBB

PBDE

Model Product Quantity

GT15-J71GP23-SX

CC-Link IE Controller Network communication unit 1

Mounting screw set (4 screws, 4 stickers) 1 Extension interface relay board 1 GOT2000/GOT1000 Series CC-Link IE Controller Network Communication Unit User's Manual (This manual)

1

A-9

1. OVERVIEW

This user's manual describes the GOT2000/GOT1000 series CC-Link IE Controller Network communication unit (hereinafter referred to as the CC-Link IE communication unit). The CC-Link IE communication unit allows the GOT2000 or GOT1000 series to function as a normal station on the CC-Link IE Controller Network. Refer to the User's Manual for the GOT used for GOT to which this unit can be installed.

2. SPECIFICATIONS

The performance specifications of the CC-Link IE communication unit are indicated below. The general specifications of the CC-Link IE communication unit are the same as those of the GOT. For the general specifications of the GOT, refer to the User's Manual for the GOT used.

When using the CC-Link IE Controller Network connection, make the communication setting to perform communication with programmable controllers. For the details of the CC-Link IE Controller Network connection, refer to the GOT2000 or GOT1000 Series Connection Manual (Mitsubishi Products).

Item Specification

Max. link points per network

LB 32K points (32768 points, 4KB) LW 128K points (131072 points, 256KB) LX 8K points (8192 points, 1KB) LY 8K points (8192 points, 1KB)

Max. link points per station

LB 16K points (16384 points, 2KB) LW 16K points (16384 points, 32KB) LX 8K points (8192 points, 1KB) LY 8K points (8192 points, 1KB)

Transient transmission capacity Up to 1920 bytes

Communication speed 1Gbps Communication method Token ring Number of stations per network

Up to 120 stations (Control station: 1, Normal station: 119)

Connection cable Fiber-optic cable (Multi-mode fiber) *1 ( CC-Link IE Controller Network Reference Manual)

1

*1 : Please note that use of a fiber-optic cable requires the expertise, special tools and dedicated connector for connection. Please contact your local Mitsubishi Electric System & Service Co., Ltd. or representative, for the purchase of the required items.

Overall cable distance 66000m (When 120 stations are connected) Station-to-station distance (Max.) 550m (Core/Clad = 50/125 ( m))

Max. number of networks 239

Max. number of groups 32 Transmission path Duplex loop Optical fiber specifications 1000BASE-SX(MMF) fiber-optic cable

Standard IEC60793-2-10 Types A1a.1 (50/125 m multimode) Transmission loss (max.) 3.5 (dB/km) or less ( = 850nm)

Transmission band (min.) 500 (MHzkm) or more ( = 850nm)

Connector specifications Duplex LC connector Standard IEC61754-20: Type LC connector Connection loss 0.3 (dB) or less

Polished surface PC (Physical Contact) polishing

Internal current consumption 1.07A

Weight 0.28kg (0.62lb)

Item Specification

2

3. PART NAMES

The following describes part names and descriptions of the CC-Link IE communication unit.

No. Name Description

1) Indicator LED Indicates the operating status of the CC-Link IE communication unit. ( (1) in this section)

2) Connector (IN side, OUT side)

Connector for connecting a fiber-optic cable ( (2) in this section)

3) Interface connector Extension connector installed to a front extension unit or the GOT

4) Extension connector Extension connector to which a back extension unit is installed

5) Board fixing screw Screws for fixing the extension interface relay board 6) Mounting screw Mounting screws fixed with a front extension unit or the GOT 7) Rating plate -

1)

7)

5)

4)

3)

2)

3)

6)

6)

3

(1) Indicator LED

A LED indicates the status of the CC-Link IE communication unit and the communication status. When the LED is lighted up, there are two display formats, one for the normal mode and the other for the error mode. (1) Normal mode

If any communication error occurs in the normal mode, specify the error cause by the [NETWK unit status display] screen of the GOT utility. Refer to the User's Manual for the GOT used for details on the [NETWK unit status display] screen.

(2) Error mode When the RUN LED is blinking, the LED display format is the error mode.In the error mode, if an error occurs, restart the GOT. If the error mode is not released after restarting the GOT, the system alarm "460 Communication unit error" may occur. For system alarms, refer to the User's Manual for the GOT used.

LED name Status Description

RUN Off The GOT is being reset. On The unit is in a normal status.

SD Off Not sending data On Sending data

RD Off Not receiving data On Receiving data

ERR. Off Normal status On Communication error

LED name Status Description

RUN Blinking Shows that it is in the error mode. On or off No error

RD Off No hardware failure On Hardware failure

ERR. Off No starting error On Starting error

4

(2) Connector (IN side, OUT side)

IN Forward loop, receiving

IN Reverse loop, sending

OUT Reverse loop, receiving

OUT Forward loop, sending

OUT IN

5

4. INSTALLATION PROCEDURE

The installation procedure for the CC-Link IE communication unit is explained using the GT1575.

(1) Power off the GOT.

(2) Remove two extension unit covers of the GOT.

(3) Attach the extension interface relay board to the extension interface 2 on the GOT. After the installation, detach the connector cover from the extension interface relay board. For the following GOT types, the extension interface relay board is not needed.

GT1655,GT155 of the GOT1000 series

GT27,GT25 of the GOT2000 series

(4) Fit the CC-Link IE communication unit in the GOT case.

(5) Fix the CC-Link IE communication unit by tightening its mounting screws (4 places) with a tightening torgue of 0.36 to 0.48 Nm.

4) 3)

Remove the connector cover.

6

(6) Fix the CC-Link IE communication unit by tightening two board fixing screws with a tightening torque of 0.36 to 0.48 Nm.

(7) When installing an extension unit on the unit that has been installed, remove the connector cover and the stickers. When not installing an extension unit on the unit that has been installed, in order to avoid receiving electrostatic, stick accessory stickers to cover the top of mounting screws (4 places). Keep the connector cover fixed. Keep the accessory sticker stuck.

Point

Remove the screws that fixes the extension interface relay board before removing the unit. (Above (6))

6)5)

Sticker

Accessory sticker

Accessory sticker

Connector cover

7

5. PRECAUTIONS FOR WIRING CABLES

(1) Wire fiber-optic cables described in the following manual.

CC-Link IE Controller Network Reference Manual

(2) For connecting fiber-optic cables to the unit, the bending radius of the cables must be within the specified range. For the details, check the specifications of the cables to be used.

(3) When wiring a fiber-optic cable, do not touch the fiber core of the cable connector or unit connector, or let dirt or dust collect on it. If oil from the hands, dirt or dust should adhere to the core, the transmission loss will increase, causing a malfunction in the data link.

(4) When connecting or removing the fiber-optic cables to/from the unit, hold the cable connector securely with the hands.

(5) Connect the cable connector and unit connector securely until you hear a "click" sound.

(6) For connecting or removing the fiber-optic cables, be sure to shut off all phases of the external power supplies used in the system.

(7) Please wire IN/OUT of the connector for the cable correctly. After wiring, perform a loop test or station-to-station test or others to confirm if the setting and wiring of CC-Link IE communication unit have been done properly. For testing methods, refer to the following manual.

CC-Link IE Controller Network Reference Manual Miswiring may cause the following and others.

Baton passing error

No loopback at any stations

Failed station that cannot reconnect to the network with reclosing the power

8

6. WIRING METHOD

(1) Connection method Connect fiber-optic cables between OUT and IN side connectors as shown below. Note that there is no need to connect the cables in the order of station numbers.

(2) Connecting fiber-optic cable

(3) Disconnecting fiber-optic cable

Control station Station No.1

P ow

er s

up pl

y m

od ul

e

C P

U m

od ul

e

Normal station Station No.2

Normal station Station No.n

CC-Link IE Controller Network module

P ow

er s

up pl

y m

od ul

e

C P

U m

od ul

e

CC-Link IE communication unit

IN OUT IN OUT

INOUT

n 120

Connector hook

CC-Link IE

communication unit

Unit-side

connectorCable-side

connector

Connection

Connect the cable-side connector to

the module-side connector, paying

attention to the orientation.

Push it until a click is heard.

Lightly pull it to check that it is

securely connected.

Completed

Turn the power off.

CC-Link IE

communication unit

Unit-side

connectorCable-side

connector

Connector hook

Completed

Disconnection

Press the connector hook to

disconnect the cable.

Turn the power off.

9

7. EXTERNAL DIMENSIONS

(1) CC-Link IE communication unit

Unit:mm (inch)

Dimensions of X when the CC-Link IE communication unit is mounted to the GOT. GOT GT27 GT25 GT16 GT15

15" 37(1.46) - 33.5(1.32) 35(1.38) 12.1" 37(1.46) 37(1.46) 32(1.26) 32(1.26) 10.4" 37(1.46) 37(1.46) 35(1.38) 35(1.38) 8.4" 37(1.46) 37(1.46) 37(1.46) 37(1.46) 5.7" 37(1.46) - 37(1.46) 37(1.46)

133(5.24) 3 (0.12)

98 (3

.8 6)

2.5 (0.10)

2 (0.08)

35 (1

.3 8)

44 (1

.7 3)

11.5 (0.45)

15.5 (0.61)

23 .5

(0 .9

3)

3 (0

.1 2) 15

(0

.5 9)

12 0(

4. 72

)

X

GOT main unit

Unit : mm(inch)

10

(2) Extension interface relay board

11

Warranty Mitsubishi Electric will not be held liable for damage caused by factors found not to be the cause of Mitsubishi Electric; machine damage or lost profits caused by faults in the Mitsubishi Electric products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi Electric; damages to products other than Mitsubishi Electric products; and to other duties.

For safe use This product has been manufactured as a general-purpose part for general industries, and

has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.

Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi Electric.

This product has been manufactured under strict quality control. However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.

Specifications subject to change without notice. Printed in Japan, November 2020.

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.

USA Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A. Tel: +1-847-478-2100

Brazil Mitsubishi Electric do Brasil Comercio e Servicos Ltda. Avenida Adelino Cardana, 293, 21 andar, Bethaville, Barueri SP, Brazil Tel: +55-11-4689-3000

Mexico Mitsubishi Electric Automation, Inc. Mexico Branch Boulevard Miguel de Cervantes Saavedra 301, Torre Norte Piso 5, Ampliacion Granada, Miguel Hidalgo, Ciudad de Mexico, Mexico, C.P.11520 Tel: +52-55-3067-7512

Germany Mitsubishi Electric Europe B.V. German Branch Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany Tel: +49-2102-486-0

UK Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, UK-Hatfield, Hertfordshire, AL10 8XB, U.K. Tel: +44-1707-28-8780

Italy Mitsubishi Electric Europe B.V. Italian Branch Centro Direzionale Colleoni - Palazzo Sirio, Viale Colleoni 7, 20864 Agrate Brianza (MB), Italy Tel: +39-039-60531

Spain Mitsubishi Electric Europe B.V. Spanish Branch Carretera de Rubi, 76-80-Apdo. 420, E-08190 Sant Cugat del Valles (Barcelona), Spain Tel: +34-935-65-3131

France Mitsubishi Electric Europe B.V. French Branch 25, Boulevard des Bouvets, 92741 Nanterre Cedex, France Tel: +33-1-55-68-55-68

Czech Mitsubishi Electric Europe B.V. Czech Branch Pekarska 621/7, 155 00 Praha 5, Czech Republic Tel: +420-255 719 200

Turkey Mitsubishi Electric Turkey A.S. Umraniye Branch Serifali Mahallesi Nutuk Sokak No:5, TR-34775 Umraniye / Istanbul, Turkey Tel: +90-216-526-3990

Poland Mitsubishi Electric Europe B.V. Polish Branch ul. Krakowska 48, 32-083 Balice, Poland Tel: +48-12-347-65-00

Russia Mitsubishi Electric (Russia) LLC St. Petersburg Branch Piskarevsky pr. 2, bld 2, lit "Sch", BC "Benua", office 720; 195027 St. Petersburg, Russia Tel: +7-812-633-3497

South Africa Adroit Technologies 20 Waterford Office Park, 189 Witkoppen Road, Fourways, South Africa Tel: +27-11-658-8100

China Mitsubishi Electric Automation (China) Ltd. Mitsubishi Electric Automation Center, No.1386 Hongqiao Road, Shanghai, China Tel: +86-21-2322-3030

Taiwan SETSUYO ENTERPRISE CO., LTD. 6F, No.105, Wugong 3rd Road, Wugu District, New Taipei City 24889, Taiwan Tel: +886-2-2299-2499

Korea Mitsubishi Electric Automation Korea Co., Ltd. 7F to 9F, Gangseo Hangang Xi-tower A, 401, Yangcheon-ro, Gangseo-Gu, Seoul 07528, Korea Tel: +82-2-3660-9569

Singapore Mitsubishi Electric Asia Pte. Ltd. 307 Alexandra Road, Mitsubishi Electric Building, Singapore 159943 Tel: +65-6473-2308

Thailand Mitsubishi Electric Factory Automation (Thailand) Co., Ltd. 12th Floor, SV.City Building, Office Tower 1, No. 896/19 and 20 Rama 3 Road, Kwaeng Bangpongpang, Khet Yannawa, Bangkok 10120, Thailand Tel: +66-2682-6522 to 31

Indonesia PT. Mitsubishi Electric Indonesia Gedung Jaya 8th Floor, JL. MH. Thamrin No.12, Jakarta Pusat 10340, Indonesia Tel: +62-21 3192-6461

Vietnam Mitsubishi Electric Vietnam Company Limited 11th & 12th Floor, Viettel Tower B, 285 Cach Mang Thang 8 Street, Ward