Mitsubishi GOT1000 GT16-60SLTT Backlight User's Manual PDF

1 of 1
1 of 1

Summary of Content for Mitsubishi GOT1000 GT16-60SLTT Backlight User's Manual PDF

User's Manual

GT16-60SLTT GT16-60VLTT GT16-60VLTN

Thank you for purchasing the GOT1000 Series.

GT16 Backlight for 8.4'' GOT

Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.

MODEL GT16-60SLTT-U

MODEL CODE

1D7M92

IB(NA)-0800447-B(1004)MEE

SAFETY PRECAUTIONS (Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly. The precautions given in this manual are concerned with this prod- uct. In this manual, the safety precautions are ranked as "DANGER" and "CAUTION".

Note that the CAUTION level may lead to a serious accident according to the circumstances. Always follow the precautions of both levels because they are impor- tant to personal safety. Please save this manual to make it accessible when required and always forward it to the end user.

Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.

DANGER

CAUTION

[BACKLIGHT REPLACEMENT PRECAUTIONS]

[STARTUP AND MAINTENANCE PRECAUTIONS]

[DISPOSAL PRECAUTIONS]

[TRANSPORTATION PRECAUTIONS]

Manuals

The following shows manuals relevant to this product.

For relevant manuals, refer to the PDF manuals stored in the CD- ROM for the drawing software used.

2009 MITSUBISHI ELECTRIC CORPORATION

Make sure to externally shut off all phases of GOT power supply (when GOT is connected via the bus type connection, make sure to shut off all phases of PLC CPU power supply as well) and remove the GOT from the control panel before backlight replacement. If all phases are not shut off, it may cause an electric shock. If backlight is replaced with the GOT on the control panel, the GOT may drop off, resulting in injuries.

Make sure to wear gloves during backlight replacement. Failure to do so may cause injuries.

Make sure to start the backlight replacement 5 or more minutes after power off of the GOT. Failure to do so may cause burn injuries as the old backlight holds heat for a while.

Before handling the GOT, make sure to touch a grounded metal object to discharge the static electricity from the human body. Failure to do so may cause the GOT to fail or malfunction.

Dispose of this product as industrial waste.

Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the GT16 User's Manual, as they are precision devices. Failure to do so may cause the unit to fail. Check if the unit operates correctly after transportation.

Detailed Manual

Manual name Manual number

(Type code)

GT16 User's Manual (Option)

SH-080778ENG (1D7M88)

Relevant Manuals

DANGER

CAUTION

CAUTION

CAUTION

CAUTION

Packing List After unpacking the box, check that the following products are included.

1. OVERVIEW

This User's Manual describes GT16 backlight fot 8.4" GOT (hereinafter referred to as the backlight). For applicable GOTs, refer to GT16 User's Manual.

2. SPECIFICATIONS

The following shows the performance specifications of the backlight. The general specifications of the backlight are the same as those of the GOT. For the general specifications of the GOT, refer to GT16 User's Manual.

3. BACKLIGHT REPLACEMENT

3.1 Preparing for Replacement

The GOT includes the backlight for liquid crystal display panel. Please note that the backlight intensity decreases in time. The backlight needs to be replaced when the display section becomes dark due to the decreased intensity and the picture is unclear. The backlight replacement procedure is described below.

1) Turn off the GOT.

2) Disconnect the power supply cable and the communication cable. Remove the GOT from the control panel.

Model Product Quantity

GT16-60SLTT GT16-60VLTT GT16-60VLTN

Backlight 1

Product Model Description GOT

Backlight

GT16- 60SLTT

For 8.4" TFT (SVGA) of high intensity and wide angle view

GT1665M-S

GT16- 60VLTT

For 8.4" TFT (VGA) of high intensity and wide angle view

GT1665M-V

GT16- 60VLTN

For 8.4" TFT (VGA) GT1662-VN

Item Specifications

GT16-60SLTT GT16-60VLTT GT16-60VLTN

Type Cold cathode tube back light

Life 50,000h or more

(Operating ambient temperature: 25 )

40,000h or more (Operating

ambient temperature:

25 )

Weight 0.006kg(0.013lb) 0.008kg (0.018lb)

3) Remove the right extension unit cover of the GOT. Remove an extension unit, including a bus connection unit, if it is mounted.

4) Remove seven fixing screws on the GOT rear face with a screwdriver.

5) Remove the case after passing the battery holder through the mounting hole.When removing, take care of not cutting the cable of the battery holder. (Expanded figure of part A in 4))

Top

Bottom

A

B

Top

3.2 Replacing Backlight

(1) GT16-60SLTTGT16-60VLTT

1) Pull out the tray for storing the cable connector ofbacklight (Expanded figure of part B in 3.1 4)).

2) Disconnect the cable connector of backlight from the GOT side connectors.

3) Press the backlight fixing latch (black) toward the direction of the following arrow with your fingers, and pull out the backlight. When pulling out the backlight, press the packing with your fingers so that the backlight does not hit the packing

Top

Latch Packing

4) Install a new backlight in the reverse procedure of removal. When inserting a new backlight into the backlight replacement hole of the GOT, make sure not to damage the sheaths of the cables. Insert the backlight until it is fixed by the latch (black). Pull the cable tight toward the right side of the tray. Insert the tray until it is fixed. (Refer to 3.2 (1) 1).) Assemble the case in the reverse procedure of disassembly. (Tighten the fixing screws on the GOT rear face with a torque of 0.36 to 0.48 Nm). When installing the case, make sure that the cables are not stuck between the case and the GOT.

(2) GT16-60VLTN

1) Pull out the tray for storing the cable connector ofbacklight (Expanded figure of part B in 3.1 4)).

2) Disconnect the cable connector of backlight from the GOT side connectors.

3) Press the backlight fixing latch (black) toward the direction of the following arrow with your fingers, and pull out the backlight. When pulling out the backlight, press the packing with your fingers so that the backlight does not hit the packing

Top

Packing Latch

4) Install a new backlight in the reverse procedure of removal. When inserting a new backlight into the backlight replacement hole of the GOT, make sure not to damage the sheaths of the cables. Insert the backlight until it is fixed by the latch (black). Route the cable under the tray to adjust cable slack. Then, pull the cable tight toward the left side of the tray. Insert the tray until it is fixed. (Refer to 3.2 (2) 1).) Assemble the case in the reverse procedure of disassembly. (Tighten the fixing screws on the GOT rear face with a torque of 0.36 to 0.48 Nm). When installing the case, make sure that the cables are not stuck between the case and the GOT.

Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other than Mitsubishi products; and to other duties.

For safe use This product has been manufactured as a general-purpose part for

general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.

Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi.

This product has been manufactured under strict quality control. However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.

Country/Region Sales office/Tel

U.S.A Mitsubishi Electric Automation Inc. 500 Corporate Woods Parkway Vernon Hills, IL 60061, U.S.A. Tel : +1-847-478-2100

Brazil MELCO-TEC Rep. Com.e Assessoria Tecnica Ltda. Rua Correia Dias, 184, Edificio Paraiso Trade Center-8 andar Paraiso, Sao Paulo, SP Brazil Tel : +55-11-5908-8331

Germany Mitsubishi Electric Europe B.V. German Branch Gothaer Strasse 8 D-40880 Ratingen, GERMANY Tel : +49-2102-486-0

U.K Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Hertfordshire., AL10 8XB, U.K. Tel : +44-1707-276100

Italy Mitsubishi Electric Europe B.V. Italian Branch Centro Dir. Colleoni, Pal. Perseo-Ingr.2 Via Paracelso 12, I-20041 Agrate Brianza., Milano, Italy Tel : +39-039-60531

Spain Mitsubishi Electric Europe B.V. Spanish Branch Carretera de Rubi 76-80, E-08190 Sant Cugat del Valles, Barcelona, Spain Tel : +34-93-565-3131

France Mitsubishi Electric Europe B.V. French Branch 25, Boulevard des Bouvets, F-92741 Nanterre Cedex, France TEL: +33-1-5568-5568

South Africa Circuit Breaker Industries Ltd. Private Bag 2016, ZA-1600 Isando, South Africa Tel : +27-11-928-2000

Hong Kong Mitsubishi Electric Automation (Hong Kong) Ltd. 10th Floor, Manulife Tower, 169 Electric Road, North Point, Hong Kong Tel : +852-2887-8870

China Mitsubishi Electric Automation (Shanghai) Ltd. 4/F Zhi Fu Plazz, No.80 Xin Chang Road, Shanghai 200003, China Tel : +86-21-6120-0808

Taiwan Setsuyo Enterprise Co., Ltd. 6F No.105 Wu-Kung 3rd.Rd, Wu-Ku Hsiang, Taipei Hsine, Taiwan Tel : +886-2-2299-2499

Korea Mitsubishi Electric Automation Korea Co., Ltd. 1480-6, Gayang-dong, Gangseo-ku Seoul 157-200, Korea Tel : +82-2-3660-9552

Singapore Mitsubishi Electric Asia Pte, Ltd. 307 Alexandra Road #05-01/02, Mitsubishi Electric Building, Singapore 159943 Tel : +65-6470-2460

Thailand Mitsubishi Electric Automation (Thailand) Co., Ltd. Bang-Chan Industrial Estate No.111 Moo 4, Serithai Rd, T.Kannayao, A.Kannayao, Bangkok 10230 Thailand Tel : +66-2-517-1326

Indonesia P.T. Autoteknindo Sumber Makmur Muara Karang Selatan, Block A/Utara No.1 Kav. No.11 Kawasan Industri Pergudangan Jakarta - Utara 14440, P.O.Box 5045 Jakarta, 11050 Indonesia Tel : +62-21-6630833

India Messung Systems Pvt, Ltd. Electronic Sadan NO:III Unit No15, M.I.D.C Bhosari, Pune-411026, India Tel : +91-20-2712-3130

Australia Mitsubishi Electric Australia Pty. Ltd. 348 Victoria Road, Rydalmere, N.S.W 2116, Australia Tel : +61-2-9684-7777

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.

Specifications subject to change without notice. Printed in

Manualsnet FAQs

If you want to find out how the GOT1000 Mitsubishi works, you can view and download the Mitsubishi GOT1000 GT16-60SLTT Backlight User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Mitsubishi GOT1000 as well as other Mitsubishi manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Mitsubishi GOT1000. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Mitsubishi GOT1000 GT16-60SLTT Backlight User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Mitsubishi GOT1000 GT16-60SLTT Backlight User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Mitsubishi GOT1000 GT16-60SLTT Backlight User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Mitsubishi GOT1000 GT16-60SLTT Backlight User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Mitsubishi GOT1000 GT16-60SLTT Backlight User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.