This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.
Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other than Mitsubishi products; and to other duties.
For safe use This product has been manufactured as a general-purpose part for general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life. Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi Electric. This product has been manufactured under strict quality control. However when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Safety Pr Before using t introduced in th product correct The precaution
In this manual, t
Depending on linked to seriou In any case, it i
MOUNTING PRECAUTION
Use the R satisfies the cause an e
OPERATION PRECAUTION
Power OF conversion Poor conne
Remove st 232/485 sig Static elect
DISPOSAL PR
When dispo
3. Specifications 3.1 General Specifications
(Other specifications are the same as the GT14 main unit.)
the terminating
he RS-232/485
al.
4) 1pair/2pair/ Terminating resistor setting switch
1Pair/2Pair Terminating resistor (110, OPEN, 330)
(At factory shipment: 2Pair, Terminating resistor 330)
Item Specifications
Operating ambient temperature 0 to 55C
Storage ambient temperature -20 to 60C
Operating/Storage ambient humidity 10 to 90% RH, non-condensing
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electro conductive dust particles
light (during
he GOT
l name
G
B
A
DB
DA
6
- OFF
- OFF
F OFF
F OFF
N OFF
5 6
FF OFF
FF OFF
N OFF
FF OFF
m
ontact Inc.)
No. Name Contents Refer to the table below for applicable wire sizes.
7. Installation 1) Turn off the GOT power. 2) Connect the RS-232/485 signal
conversion adapter to the RS-232 interface on the GOT.
3) Fix the RS-232/485 signal conversion adapter to the GOT using the provided M3 tapping screws. Tightening torque: 0.3 to 0.6 Nm
8. Cautions on use of RS-232/485 signal conversion adapter
When using the RS-232/485 signal conversion adapter, select [Communication setting] [5V power supply] [YES] on the utility screen in the GT14 main unit. For details, refer to the following.
GOT2000 Series User's Manual (Utility) GT14 Users Manual (8.2 Utility Function List)
The GT14 main unit whose hardware version is B or later supports the setting whether or not 5V power is supplied. In the hardware version A, the setting operation about 5V power supply is invalid because 5V power is always supplied.
When using the RS-232/485 signal conversion adapter, make sure that the core OS version is V05.28.00AP or later and the standard monitor OS version is V05.28.00 or later in the GT14 main unit. For details, refer to the following.
GT14 Users Manual (12.1.2 OS version confirmation)
No. of wire per terminal
Electrical wire size
Solid wire Stranded wire Ferrules with plastic sleeve
1 0.14 to 1.5mm2
AWG26 to AWG16 0.14 to 1.0mm2
AWG26 to AWG16 0.25 to 0.5 mm2
AWG24 to AWG20
2 0.14 to 0.5mm2
AWG26 to AWG20 0.14 to 0.2mm2
AWG26 to AWG24 -
RS-232
This manual de the product. Be to acquire profi the product info And, store this whenever nece Registration The company n registered trade
Effective April 2 Specifications a
lectric shock, fire, malfunction or product damage or deterioration.
S
F the GOT, and then connect securely the RS-232/485 signal adapter to the specified connector in the GOT. ction may cause malfunction.
atic electricity charged in the human body before handling the RS- nal conversion adapter.
ricity may damage the stored data and elements.
ECAUTIONS
sing of the product, handle it as industrial waste.
2. Part Names and External Dimensions
No. Name Contents
1) RS-485 terminal block 5-pin (Fixed type)
2) GOT connector D-Sub 9-pin female
3) Fixing screw hole M3 tapping screws (accessory)
1)
4)
3)
2)
48 (1
.8 9"
)
36 (1.42") (0.67")
17
Unit: mm (inch)
Set "1 pair" or "2 pairs" using the switches Nos. 1 and 2, and set resistor value using the switches Nos. 3 to 6.
Do not manipulate the setting switches while power is supplied to t signal conversion adapter.
6. Wiring For the detail, refer to GOT2000/GOT1000 Series Connection Manu
330 - - OFF ON O
Format Terminating resistor
Switch No.
1 2 3 4
1pair 110 ON ON ON OFF O
OPEN ON ON OFF OFF O
2pair 330 OFF OFF OFF ON O
OPEN OFF OFF OFF OFF O
Cable jacket to remove 5mm (0.19)
Tightening torque 0.22 to 0.25 N
Recommended Tool (Screwdriver) SZS 0.42.5 (Phoenix C
ecaution (Read these precautions before using.) his product, please read this manual and the relevant manuals is manual carefully and pay full attention to safety to handle the
ly. s given in this manual are concerned with this product.
he safety precautions are ranked as and .
circumstances, procedures indicated by may also be s results. s important to follow the directions for usage.
Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.
S
S-232/485 signal conversion adapter in the environment that general specifications described in this manual. Not doing so can
Referenced Standard: GB/T15969.2 (Requirement of Chinese standardized law)
1. Overview The GT14-RS2T4-9P RS-232/485 signal conversion adapter (hereinafter referred to as "RS-232/485 signal conversion adapter") converts the RS-232 communication interface of the GOT into the RS-485 communication interface. Applicable GOT units are shown below.
GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3
SH-080868ENG (1D7MC2)
Describes system configurations of the connection method applicable to GOT1000 series and cable creation method. (sold separately)
GOT1000 Series Connection Manual (Non-Mitsubishi Products 1) for GT Works3
SH-080869ENG (1D7MC3)
Describes system configurations of the connection method applicable to GOT1000 series and cable creation method. (sold separately)
GOT1000 Series Connection Manual (Non-Mitsubishi Products 2) for GT Works3
SH-080870ENG (1D7MC4)
Describes system configurations of the connection method applicable to GOT1000 series and cable creation method. (sold separately)
GOT1000 Series Connection Manual (Microcomputer, MODBUS Products, Peripherals) for GT Works3
SH-080871ENG (1D7MC5)
Describes system configurations of the connection method applicable to GOT1000 series and cable creation method. (sold separately)
GOT
GOT 2000 GT2505-VTBD
GOT 1000 GT1455-QTBDE, GT1450-QLBDEGT1455-QTBD, GT1450-QLBD
4. Pin assignment
5. 1pair/2pair/Terminating resistor setting switch
Operating atmosphere and must not be exposed to direct sun operation and storage).
Power consumption 0.5W or less (100mA/5VDC), supplied from t
Pin No. Signa
1 S
2 SD
3 SD
4 R
5 R
Setting item
Set value
Switch No.
1 2 3 4 5
1pair/2pair 1pair ON ON - -
2pair OFF OFF - -
Terminating resistor
110 - - ON OFF OF
OPEN - - OFF OFF OF
1 2 3 4 5
Tightening torque: 0.22 to 0.25Nm
1 O
2 N
3 4 5 6
ame and the product name to be described in this manual are the marks or trademarks of each company.
018 re subject to change without notice.
2011 MITSUBISHI ELECTRIC CORPORATION
Side A
Side
B JAPANESE
ENGLISHSide B
JY997D44401E
Related Manuals The following manuals are relevant to this product. When these loose manuals are required please consult with our local distributor.
Manual name Manual Number
(Model Code) Contents
GOT2000 Series User's Manual (Hardware)
SH-081194ENG (1D7MJ5)
Describes the GOT hardware relevant content such as part names, external dimensions, mounting, power supply wiring, specifications, and introduction to option devices
GOT2000 Series Handy GOT Connection Manual For GT Works3 Version1
SH-081867ENG (1D7MS9)
Describes system configurations of the connection method applicable to GOT2000 Series Handy GOT and cable creation method
GT14 User's Manual JY997D44801 (09R823)
Describes the GT14 hardware-relevant content such as part names, external d imens ions , moun t ing , w i r i ng , specifications, and introduction to option devices. (sold separately)
GT14-RS2T4-9P /485 Signal Conversion Adapter
User's Manual
scribes th
en
ja
zh