Mitsubishi Motors MZ574482EX Installation Instructions PDF

1 of 4
1 of 4

Summary of Content for Mitsubishi Motors MZ574482EX Installation Instructions PDF

Isopropyl alcohol or degreaser Shop towel

B1100(062)

OUTLANDER REAR BUMPER PLATE

MZ574482EX INSTALLATION AND HANDLING INSTRUCTIONS

Thank you for purchasing the Mitsubishi Genuine Accessory. To install and use the product correctly with proper knowledge of it, read this publication carefully. Keep this publication for reference when maintenance is required.

Attention

This publication gives precautionary instructions in the boxes titled as follows. Read through these instructions thoroughly.

Describes precautions that should be observed in order to prevent injury or damage to the vehicle or its components, which may occur if sufficient care is not taken.

Provides additional information that facilitates installation work.

Failure to follow these instructions not only prevents the product from working properly but may lead to trouble with the vehicle. Be sure to follow all instructions carefully.

If there is anything unclear about the installation, handling and/or usage of the product, contact your Mitsubishi Motors dealer for clarification.

Mitsubishi Motors Corporation is not responsible for any defects or difficulties caused by or resulting from the failure to follow given instructions.

We recommend you to have the installation performed at an authorized Mitsubishi Motors dealer.

To the dealer: Be sure that the customer receives this publication.

TOOLS (Make the following tools ready for use.)

Caution

Note

a Rear Bumper Plate: 1

Degrease.

2

COMPONENTS(Make sure that all of the following components were included in the kit.)

PRECAUTIONS This product may not be installed together with some other Mitsubishi genuine accessories. Check for

applicability before installing this product. Park the vehicle on a flat, horizontal place. Be sure to apply parking brake securely. Remove the ignition key from its key cylinder. Be careful not to apply excessive force to the product. It may deform the product, causing faulty installa-

tion. Adhesive tape extremely loses its adhesion if the adhesive surface is touched by a dirty hand or glove,

or if the tape is removed after application. If the adhesion is reduced, take appropriate remedies such as replacing the adhesive tape, otherwise the product may fall off during driving.

Low ambient temperature (below 15C) greatly reduces the adhesion of adhesive tape, which can be a cause of peeling off. Work in a warm place or warm the tape application surface as necessary.

INSTALLATION PROCEDURES

A. INSTALLING THE REAR BUMPER PLATE

1) Wipe clean and degrease the Rear Bumper Plate a installation surface.

To degrease the surface, use isopropyl alcohol or degreaser. Never use paint thinner, benzene, gasoline, or any other organic solvent for this purpose. Ignoring this process may cause falling off of the product.

Caution

a

Peel the ends of the backing strips.

Peel the ends of the backing strips.

Set against the stepped portion.

Rear bumper

Press.

Press.

a

3

2) Peel off the ends of the backing strips from the adhesive tapes at the back of the Rear Bumper Plate a.

3) Place the Rear Bumper Plate a on the rear bum- per. Set the front end of the Rear Bumper Plate a against the stepped portion of the rear bum- per. Then adjust the clearances and to be even.

Note Affixing the peeled ends on the surface of the plate with adhesive tape will facilitate the later steps.

4) After confirming the balance of installation posi- tion, peel off the backing strips and press the Rear Bumper Plate a firmly against the bumper.

5) Press the Rear Bumper Plate a firmly against the bumper again for reconfirmation.

4

B. CHECKING AFTER INSTALLATION Check if the product fits properly on the vehicle body. Check if the worked area on the vehicle body is clean. Check if the adhesive tape sticks firmly.

Do not wash the vehicle for 24 hours after attaching the product to prevent peeling off of the prod- uct. Even if washing or waxing is necessary, wait at least 6 hours. Keep the vehicle off the rain during this storage period.

Caution

CARE AND HANDLING

If the product is damaged, repair or replace it immediately. Do not apply excessive force on the product. It may deform or damage the product. This product is made of stainless steel. To remove dirt on the product, wipe it off by soft cloth moistened

with neutral detergent. Leaving the product dirty may cause rust on the product. Rust can be removed

Manualsnet FAQs

If you want to find out how the MZ574482EX Mitsubishi MOTORS works, you can view and download the Mitsubishi Motors MZ574482EX Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for Mitsubishi MOTORS MZ574482EX as well as other Mitsubishi MOTORS manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a Mitsubishi MOTORS MZ574482EX. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Mitsubishi Motors MZ574482EX Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Mitsubishi Motors MZ574482EX Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Mitsubishi Motors MZ574482EX Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Mitsubishi Motors MZ574482EX Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Mitsubishi Motors MZ574482EX Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.