Mitsubishi Motors MZ570256EX Installation Instructions PDF

1 of 3
1 of 3

Summary of Content for Mitsubishi Motors MZ570256EX Installation Instructions PDF

Wrench (10 mm) Scale (150 mm)Shop towel

(07B1316)

OUTLANDER / LANCER (for 2.0 L) MUFFLER CUTTER

MZ570256EX INSTALLATION AND HANDLING INSTRUCTIONS

Thank you for purchasing the Mitsubishi Genuine Accessory. To install and use the product correctly with proper knowledge of it, read this publication carefully. Keep this publication for reference when maintenance is required.

Attention

This publication gives precautionary instructions in the boxes titled as follows. Read through these instructions thoroughly.

Describes precautions that should be observed in order to prevent injury or damage to the vehicle or its components, which may occur if sufficient care is not taken.

Provides additional information that facilitates installation work.

Failure to follow these instructions not only prevents the product from working properly but may lead to trouble with the vehicle. Be sure to follow all instructions carefully.

If there is anything unclear about the installation, handling and/or usage of the product, contact your Mitsubishi Motors dealer for clarification.

Mitsubishi Motors Corporation is not responsible for any defects or difficulties caused by or resulting from the failure to follow given instructions.

We recommend you to have the installation performed at an authorized Mitsubishi Motors dealer.

To the dealer: Be sure that the customer receives this publication.

TOOLS (Make the following tools ready for use.)

Caution

Note

a Muffler Cutter: 1

Muffler

b Bolt (M6 x 20): 1

c Spring washer (M6): 1

d Under bracket: 1

The following parts are supplied as assembled to the Muffler Cutter.

d Under bracket

c Spring washer

b Bolt

Wipe

Attaching surface of Muffler Cutter a

2

COMPONENTS(Make sure that all of the following components were included in the kit.)

PRECAUTIONS Never perform this work immediately after turning off the engine. Perform the work after the vehicles

muffler has cooled down sufficiently. Take sufficient care not to damage the vehicle body during installation. Strictly observe the instructions for positioning of the product. Otherwise it may interfere with the

vehicles muffler or may cause abnormal exhaust noise.

INSTALLATION PROCEDURES

A. PREPARATORY WORK 1) Wipe clean the product attaching surface on the

muffler with shop towel.

Muffler

Muffler Cutter a

Muffler

Bolt b Muffler Cutter a

Insert

3

B. INSTALLING THE MUFFLER CUTTER 1) Place the Muffler Cutter a over the muffler.

2) Position the Muffler Cutter a as shown in the drawing.

Muffler end to Muffler Cutter end dimension : 10 mm

3) After confirming the installation position, tighten the bolt b.

Tighten the bolt b securely. Other- wise the Muffler Cutter a may fall off.

Do not overtighten the bolt b and deform the muffler.

Caution

CARE AND HANDLING

The bolt may become loose due to break-in. Be sure to retighten the bolt. Periodically check the bolt for looseness. This product is made of stainless steel. It may, however, rust depe

Manualsnet FAQs

If you want to find out how the MZ570256EX Mitsubishi MOTORS works, you can view and download the Mitsubishi Motors MZ570256EX Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for Mitsubishi MOTORS MZ570256EX as well as other Mitsubishi MOTORS manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a Mitsubishi MOTORS MZ570256EX. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Mitsubishi Motors MZ570256EX Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Mitsubishi Motors MZ570256EX Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Mitsubishi Motors MZ570256EX Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Mitsubishi Motors MZ570256EX Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Mitsubishi Motors MZ570256EX Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.