- Manuals
- Brands
- Mitsubishi MOTORS
- Camera
- MZ380461EX
- Installation Instructions
Mitsubishi Motors MZ380461EX Installation Instructions PDF
Summary of Content for Mitsubishi Motors MZ380461EX Installation Instructions PDF
284-1459-00 (08B1265)
OUTLANDER REAR VIEW CAMERA
MZ380461EX INSTALLATION AND HANDLING INSTRUCTIONS
Thank you for purchasing the Mitsubishi Genuine Accessory. To install and use the product correctly with proper knowledge of it, read this publication carefully. Keep this publication for reference when maintenance is required.
This publication gives precautionary instructions in the boxes titled as follows. Read through these instructions thoroughly.
Describes precautions that should be observed in order to prevent injury or damage to the vehicle or its components, which may occur if sufficient care is not taken.
Provides additional information that facilitates installation work.
Failure to follow these instructions not only prevents the product from working properly but may lead to trou- ble with the vehicle. Be sure to follow all instructions carefully.
If there is anything unclear about the installation, handling and/or usage of the product, contact your Mitsubi- shi Motors dealer for clarification.
Mitsubishi Motors Corporation is not responsible for any defects or difficulties caused by or resulting from the failure to follow given instructions.
We recommend you to have the installation performed at an authorized Mitsubishi Motors dealer.
Camera
Camera
Navigation (MMCS) unit
Attention
To the dealer: Be sure that the customer receives this publication.
Caution
Note
-2-
j TOOLS (Make the following tools ready for use.)
j COMPONENTS (Make sure that all of the following components were included in the kit.)
Camera (CC-1133M-A): 1 Bolt with washer (M5 14): 2 Supporter: 1
Jack nut: 2 Bolt (M5 25): 2 Urethane sheet: 10
Tie wrap (150 mm): 20 Template Installation and Handling Instructions : 1 (this document)
Cloth tape
Socket wrench Flat-blade screwdriverPhillips screwdriver Trim remover
Drill Drill bit (3.0, 5.0, 6.0, 8.0, 10 mm)
Touch-up paint
Hole saw (28 mm)
WireFile
Center punch
Utility knife Scissors
Vinyl tapeThread-lock cement
1 2 3
4 5 6
7 8 9
-3-
j REQUIRED COMPONENTS (sold separately)
j PRECAUTIONS Be sure to apply the parking brake securely. Remove the ignition key from the key cylinder. When removing and reinstalling the vehicle parts, perform the work including the tightening torques in accor-
dance with the workshop manual. Disconnecting the () cable from the battery causes the radio and audio presets, the clock, etc. to lose their
memory. Record the contents of the memory before disconnecting the battery () cable to allow you to repro- gram the radio presets after the installation is completed.
Camera harness (MZ380277EX) (for Australia) Camera harness (MZ607384EX) (for EU and U.S.)
-4-
Be sure to disconnect the negative terminal cable from the battery.
Loosen or tighten bolts and nuts using tools that match their sizes.
Use a Phillips screw- driver that fits the recess in the head of the screw being loos- ened or tightened.
To remove plastic parts, use a trim remover.
When disconnecting connectors, first unlock them, then separate the connectors by pulling on themselves, not on cables.
When connecting con- nectors, push them against each other until the lock clicks.
Do not pull on wiring harnesses strongly.
Do not let harnesses be pinched between parts.
Route the harness away from hot compo- nents such as the engine and radiator.
Protect the harness from sharp edges by covering the edges with tape or other suitable materials.
Apply sealant to grom- mets at portions where the harness run through.
Do not fasten the har- ness to brake pipes or high pressure air condi- tioner pipes.
Fasten the additional harness to an existing vehicle harness using tape or tie wraps.
Bind up extra length of the harness using a tie wrap.
If one tie wrap is too short, use two con- nected together.
Check the product and wiring for installed con- dition before connect- ing the cable to the battery.
Check the installed product for function. Also check lamps, horn, wipers, etc. for proper operation.
click!
click!
click!
Beep
Before installation When installing or removing parts
Wiring
Clamping harness After installation
-5-
INSTALLATION PROCEDURES A. REMOVING THE VEHICLE PARTS
(1) 1) Disconnect the battery negative cable.
2) Remove the tailgate upper trim.
3) Remove the right and left tailgate opening side trims.
4) Remove the tailgate trim.
5) Remove the tail lamps by removing the three nuts for each.
6) Remove the right and left license plate lamps.
7) Remove the tailgate garnish.
Tailgate trim
Clip
Tailgate upper trim Tailgate opening side trim (left and right)
For vehicles with side airbags, allow at least 60 seconds after disconnect- ing the battery negative cable before starting to remove the drivers or front passengers seat.
The SRS holds sufficient voltage to operate the side airbags for a while, so the side airbag could be deployed accidentally if you start working on the front seat soon after disconnect- ing the battery negative cable.
Caution
Tail lamp mounting nut
Tail lamp
Tail lamp
Tailgate garnishLicense plate lamp
Wiper motor assembly Tailgate garnish mounting bolt
Remove the two tailgate garnish mounting bolts from inside the tailgate.
-6-
8) Remove the interior lamp cover.
9) Remove the interior lamp unit by removing the two screws.
10) Remove the three headlining mounting clips shown in the drawing.
11) Remove the rear end plate by removing the three screws.
12) Remove the right rear scuff plate by removing the two clips.
13) Remove the center pillar trim, lower.
Headlining mounting clip
Interior lamp unit
Screw
Lamp cover
Screw
Rear end plate
Center pillar trim, lower
Clip
Rear scuff plate, right
Check
-7-
B-1. REMOVING THE VEHICLE PARTS (2) (for left-hand drive vehicles)
1) Remove the four front passengers seat mounting bolts. Disconnect the connector under the seat.
2) Bring down the front passengers seat backward.
3) Remove the jack stowage cover and remove the jack.
4) Remove the right quarter lower trim by removing the two bolts and six screws and disconnecting the three connectors.
5) Remove the right quarter upper trim by removing the two bolts and two clips.
6) Remove the lower side cover by removing the one screw and one clip.
7) Remove the right front scuff plate.
8) Remove the right cowl side trim.
Cover
Bolt
Disconnect the connector.
Bring down the seat backward.
Cover
Bolt
Right quarter upper trim Bolt
BoltCover
Cover
Clip
Screw
Right quarter upper trim
Bolt
Tapping screw
Jack stowage cover
Hook
Screw
Lower side cover
Right front scuff plate Right cowl side trim
-8-
9) Turn over the floor carpet and remove the silent plate.
10) Remove the center air outlets.
11) Remove the center panel assembly by removing the two screws.
12) Remove the navigation (MMCS) unit by removing the four screws.
B-2. REMOVING THE VEHICLE PARTS (2) (for right-hand drive vehicles)
1) Remove the four drivers seat mounting bolts. Dis- connect the connector under the seat.
2) Bring down the drivers seat backward.
Silent plate
Screw
Center panel assembly
Center air outlet
Bracket mounting screw
Navigation (MMCS) unit
Bolt
Cover
Disconnect the connector.
Bring down the seat backward.
Cover
Bolt
Check
-9-
3) Remove the console side cover by removing the one screw and one clip.
4) Remove the foot rest by removing the one nut.
5) Remove the two mat hooks by removing the two screws.
6) Turn over the floor carpet and remove the silent plate.
7) Remove the center air outlets.
8) Remove the center panel assembly by removing the two screws.
9) Remove the navigation (MMCS) unit by removing the four screws.
Foot rest
Console side cover
Floor mat hook (2 places)
Silent plate
Screw
Center panel assembly
Center air outlet
Bracket mounting screw
Navigation (MMCS) unit
Check
-10-
C. MODIFYING THE TAILGATE PANEL 1) Cut out the template .
2) Align the hatched section on the template with the left license plate lamp mounting hole and secure the template on the tailgate panel using vinyl tape.
3) Mark the centers of the ten drilling holes using a center punch.
4) Apply the cloth tape underneath the drilling por- tions to prevent the drilling chips from scattering around.
5) Wrap the drill bit with vinyl tape at the position 10 mm away from the drill tip to prevent it from pene- trating unnecessary.
6) Remove the template. Using the punched marks as references, drill the following holes. 10 mm hole 2: 3 mm base hole 6 mm
base hole 10 mm hole 8 mm hole 4: 3 mm base hole 6 mm
base hole 8 mm hole 6 mm hole 2: 3 mm base hole 6 mm
hole 5 mm hole x 1: 3 mm base hole 5 mm
hole 28 mm hole 1: 3 mm base hole 28 mm
hole (using a hole saw)
7) After drilling, shape the camera mounting hole roughly to a square hole using a file.
8) Remove the burrs around the drilled holes using a file. Apply touch-up paint to prevent corrosion.
Template
External view of tailgate
Vinyl tape License plate
10 mm 10 mm
28 mm
5 mm 8 mm 4
6 mm 2
8
8
8
Drill tip
Wind vinyl tape.
A pp
ro x.
1 0
m m
During drilling work, always wear gog- gles to protect your eyes from drilling chips.
Before drilling, make sure that there are no harnesses and pipes under- neath the drilling position. If any har- ness or pipe is damaged, it could cause a fire or short-circuit.
Caution
Check
-11-
D. MODIFYING THE TAILGATE GARNISH
1) Cut off the tailgate garnish (hatched section) along the scribed line.
E. COVERING THE CAMERA CABLE TERMINALS
1) Before routing the camera cable, wrap its terminals to their ends with vinyl tape so as not to damage them during routing.
Cut off.
Cut along the scribed line.
If available, use an ultrasonic cutter or saw-blade type utility knife to shorten the work time.
Note
Camera cable (MZ380277EX or MZ607384EX) Terminal
Vinyl tape
When winding the vinyl tape, be careful not to bend or break the terminals. Such damage may result in an open circuit or poor contact.
Caution
Check
Check
-12-
F-1. CONNECTING THE CAMERA CABLE TO THE NAVIGATION UNIT (for EU and U.S.)
1) Use the camera cable MZ607384EX. Connect the connector of the camera cable to the camera connector at the backside of the navigation (MMCS) unit.
If a vehicle harness is already connected to the camera connector, disconnect the harness and bundle it with vinyl tape within the dashboard. (This vehicle harness will not be used.)
Note
Disconnect the vehicle harness from the camera connector and bundle it with vinyl tape (if equipped).
Camera cable (MZ380277EX or MZ607384EX)
* A right-hand drive vehicle is shown.
Camera connector
Check
-13-
F-2. CONNECTING THE CAMERA CABLE TO THE NAVIGATION UNIT (for Australia)
1) Disconnect the 24-pin connector from the backside of the navigation (MMCS) unit.
2) Open the stopper of the 24-pin connector.
3) Use the camera cable MZ380277EX. Insert the five terminals of the camera cable into the cavities of the 24- pin connector as shown in the drawing.
4) Close the stopper of the 24-pin connector.
5) Reconnect the 24-pin connector to the backside of the navigation (MMCS) unit.
Push both tabs to open the stopper.
Backside of connector
SB1 (clear)
GND (orange) Camera cable (MZ380277EX)
A
R-EX (blue)
VRV (white)
ACC (red)
View A
Close the stopper.
OrangeClearBlue
WhiteRed
Be sure to insert the connector into the correct cavity. Incorrect installation may damage the navigation (MMCS) unit.
Caution
The camera cable has a 5-terminal end and a 4-terminal end.
Note
Camera cable
Reconnect the 24-pin connector here.
24-pin connector
Check
-14-
G. ROUTING THE CAMERA CABLE IN THE CABIN
1) Route the camera cable toward the right side of the vehicle. The camera cable should be fixed to the floor using the urethane sheets cut in half.
2) Route the camera cable toward the rear of the vehicle along the existing vehicle harness. Bundle the camera cable with the vehicle harness using the tie wraps .
Left-hand drive vehicles
Camera cable
Urethane sheet6
Tie wrap7
Urethane sheet (cut in half)
6
Urethane sheet (cut in half)
6
Right-hand drive vehicles
Camera cable
Urethane sheet6
Tie wrap7
Urethane sheet (cut in half)
6
Urethane sheet (cut in half)
6
6
Seat belt Front of the vehicle
Rear seat
Tie wrap7
Camera cable
7
Never bundle the washer tube together. Doing so may cause the washer system to fail.
Caution
-15-
3) Route the camera cable along the vehicle harness as shown in the drawing. Fix the camera cable using the tie wraps and urethane sheets cut in half.
H. ROUTING THE CAMERA CABLE IN THE TAILGATE
1) Release both ends of the grommet at the tailgate opening.
7 6
Never bundle the washer tube together. Doing so may cause the washer system to fail. Caution
Camera cable
Urethane sheet (cut in half)6 Adjust the excess cable length here.
Urethane sheet (cut in half)
6
Tie wrap7
Tie wrap7
Grommet
Headlining
Check
-16-
2) Route the camera cable inside the headlining. Wrap the urethane sheets around the camera cable from near the grommet opening to the right edge of the headlining.
3) Using a wire, pass the camera cable through the grommet into the tailgate panel.
4) Route the camera cable along the vehicle harness. Bundle the camera cable with the vehicle harness using the tie wraps .
5) Reinstall the grommet.
Tie wrap7
Camera cable Wrap the urethane sheets to the right edge of the
headlining. 6
6
Camera cable
Tie wrap7 Tie wrap7
Opening at top of tailgate
When passing the camera cable through the grommet using a wire, be careful not to damage the grommet, vehicle harness, camera cable, and its terminals.
Never pull the camera cable violently as it may break the cable.
Caution
Applying a small amount of soapy water in the grommet will facilitate the work.
Note
7
Never attach the tie wrap or urethane sheet to the washer tube. Doing so may cause the washer system to fail.
7 6
Caution
Check
-17-
I. INSTALLING THE 6-PIN CONNEC- TOR TO THE CAMERA CABLE
1) Prepare the 6-pin connector supplied together with the camera cable.
2) Remove the stopper from the connector.
3) Peel off the vinyl tape covering the terminals of the camera cable for protection.
4) Insert the four terminals of the camera cable into the cavities of the connector as shown in the draw- ing.
5) Reinstall the stopper.
Remove the stopper.
6-pin connector
6-pin connector
Backside of connector
SB1 (clear) R-EX (blue)
Camera cable
VRV (white)
ACC (red)
6-pin connector
Reinstall the stopper.
ClearBlueWhite
Red
View A
A
Peel off carefully, otherwise an open-cir- cuit or poor connection of the cable will result.
Caution
Be sure to insert the connector into the correct cavity. Incorrect installation may cause damage to the navigation (MMCS) unit.
Caution
Check
-18-
J. INSTALLING THE CAMERA 1) Install the two jack nuts to the 10-mm camera
mounting screw holes. Refer to Installation of jack nut below.
2) Apply thread-lock cement to the two bolts with washers as shown in the drawing and install the camera using these bolts .
3) Fit the two clips of the harness on the camera into the mounting holes on the backside of the tail- gate panel.
4) Connect the 6-pin connector of the camera cable to that of the camera .
5) Bundle the camera cable with the vehicle harness using the tie wraps .
Installing the jack nut
1) Insert the jack nut to its mounting hole.
2) Hold the jack nut with the supporter and screw in the bolt into the jack nut through the supporter .
3) When the jack nut is fixed securely, remove the bolt .
K. CHECKING AFTER INSTALLATION 1) Reinstall all the removed parts to the vehicle in accordance with the workshop manual.
2) Reconnect the battery negative cable. 3) Check that the electrical systems operate properly. 4) Reprogram the radio and audio memories and adjust the clock. For the reprogramming procedure, refer to
the owners handbook.
Connect the 6-pin connectors of the camera cable and camera.
Tie wrap7 Camera1 Jack nut4
Camera cable Harness of the camera 1
Bolt with washer2
Apply thread-lock cement here.Interior side of tailgate
Tie wrap7
2 1 2
1
1
7
10 mm hole
Insert. Jack nut4
Supporter3
Bolt (M5 25)
5
Tighten.
Remove the bolt .5
4
4 3 5 4
3
4 5
Camera
Tailgate garnish
Check
Check
-19-
CABLE CONNECTION
Camera connector
Camera cable (MZ380277EX)
Rear view camera
Rear view camera
Camera cable (MZ607384EX)
24-pin connector
For EU and U.S. For Australia
Navigation (MMCS) unitNav
Related manuals for Mitsubishi Motors MZ380461EX Installation Instructions
Manualsnet FAQs
If you want to find out how the MZ380461EX Mitsubishi MOTORS works, you can view and download the Mitsubishi Motors MZ380461EX Installation Instructions on the Manualsnet website.
Yes, we have the Installation Instructions for Mitsubishi MOTORS MZ380461EX as well as other Mitsubishi MOTORS manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Installation Instructions should include all the details that are needed to use a Mitsubishi MOTORS MZ380461EX. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Mitsubishi Motors MZ380461EX Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Mitsubishi Motors MZ380461EX Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Mitsubishi Motors MZ380461EX Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Mitsubishi Motors MZ380461EX Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Mitsubishi Motors MZ380461EX Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.