Contents

Mitsubishi Electric CNC Meldas 60, 60S Series Users Manual v2 PDF

1 of 443
1 of 443

Summary of Content for Mitsubishi Electric CNC Meldas 60, 60S Series Users Manual v2 PDF

MELDAS is a registered trademark of Mitsubishi Electric Corporation. Other company and product names that appear in this manual are trademarks or registered trademarks of the respective companies.

PREFACE

This manual is the alarm/parameter guide required to use the MELDAS60/60S Series. This manual is prepared on the assumption that your machine is provided with all of the MELDAS60/60S Series functions. Confirm the functions available for your NC before proceeding to operation by referring to the specification issued by the machine manufacturer. * The "MELDAS60 Series" includes the M64A, M64, M65, M66 and M65V. * The "MELDAS60S Series" includes the M64AS, M64S, M65S and M66S. Notes on Reading This Manual (1) This manual explains general parameters as viewed from the NC.

For information about each machine tool, refer to manuals issued from the machine manufacturer. If the descriptions relating to restrictions and allowable conditions conflict between this manual and the machine manufacturer's instruction manual, the later has priority over the former.

(2) This manual is intended to contain as much descriptions as possible even about special operations.

The operations to which no reference is made in this manual should be considered impossible. (3) The M64D system explained in this manual includes the M64AS, M64S, M65S and M66S. (4) The special display unit explained in this manual is the display unit incorporated by the machine

manufacturer, and is not the MELDAS standard display unit.

Caution

If the descriptions relating to the restrictions and allowable conditions conflict between this manual and the machine manufacturers instruction manual the latter has priority over the former.

The operations to which no reference is made in this manual should be considered impossible.

This manual is complied on the assumption that your machine is provided with all optional functions. Confirm the functions available for your machine before proceeding to operation by referring to the specification issued by the machine manufacturer.

In some NC system versions there may be cases that different pictures appear on the screen the machine operates in a different way or some function is not activated.

Precautions for Safety

Always read the specifications issued by the machine maker, this manual, related manuals and attached documents before installation, operation, programming, maintenance or inspection to ensure correct use. Understand this numerical controller, safety items and cautions before using the unit. This manual ranks the safety precautions into "DANGER", "WARNING" and "CAUTION".

DANGER

When the user may be subject to imminent fatalities or major injuries if handling is mistaken.

WARNING

When the user may be subject to fatalities or major injuries if handling is mistaken.

CAUTION

When the user may be subject to injuries or when physical damage may occur if handling is mistaken.

Note that even items ranked as " CAUTION", may lead to major results depending on the situation. In any case, important information that must always be observed is described.

DANGER

Not applicable in this manual.

WARNING

Not applicable in this manual.

CAUTION

1. Items related to product and manual

If the descriptions relating to the restrictions and allowable conditions conflict between this manual and the machine manufacturers instruction manual the latter has priority over the former.

The operations to which no reference is made in this manual should be considered impossible.

This manual is complied on the assumption that your machine is provided with all optional functions. Confirm the functions available for your machine before proceeding to operation by referring to the specification issued by the machine manufacturer.

In some NC system versions there may be cases that different pictures appear on the screen the machine operates in a different way on some function is not activated.

2. Items related to faults and abnormalities

If the BATTERY LOW alarm is output, save the machining programs, tool data and parameters to an input/output device, and then replace the battery. If the BATTERY alarm occurs, the machining programs, tool data and parameters may be damaged. After replacing the battery, reload each data item.

[Continued on next page]

CAUTION [Continued]

3. Items related to maintenance

Do not replace the battery while the power is ON.

Do not short-circuit, charge, heat, incinerate or disassemble the battery.

Dispose of the spent battery according to local laws.

4. Items related to servo parameters and spindle parameters

With the MDS-C1 Series, only the serial encoder is compatible as the motor end detector. The OHE/OHA type detector cannot be used as the motor end detector.

Do not adjust or change the parameter settings greatly as operation could become unstable.

In the explanation on bits, set all bits not used, including blank bits, to 0.

Disposal

(Note) This symbol mark is for EU countries only. This symbol mark is according to the directive 2006/66/EC Article 20 Information for end- users and Annex II.

Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and/or reused. This symbol means that batteries and accumulators, at their end-of-life, should be disposed of separately from your household waste. If a chemical symbol is printed beneath the symbol shown above, this chemical symbol means that the battery or accumulator contains a heavy metal at a certain concentration. This will be indicated as follows: Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%) In the European Union there are separate collection systems for used batteries and accumulators. Please, dispose of batteries and accumulators correctly at your local community waste collection/ recycling centre.

Please, help us to conserve the environment we live in!

CONTENTS

I EXPLANATION OF ALARMS

1. List of Alarms ...........................................................................................................................................1 1.1 Operation Alarms .................................................................................................................................1 1.2 Stop Codes...........................................................................................................................................9 1.3 Servo/Spindle Alarms.........................................................................................................................14 1.4 MCP Alarm .........................................................................................................................................24 1.5 System Alarms ...................................................................................................................................27 1.6 Absolute Position Detection System Alarms......................................................................................32 1.7 Messages During Emergency Stop....................................................................................................35 1.8 Auxiliary Axis Alarms..........................................................................................................................37 1.9 Computer Link Errors .........................................................................................................................44 1.10 User PLC Alarms..............................................................................................................................45 1.11 Network Service Errors ....................................................................................................................46

2. Operation Messages on Setting And Display Unit .............................................................................47 2.1 Operation Errors.................................................................................................................................47 2.2 Operator Messages............................................................................................................................58

2.2.1 Search And Operation Related....................................................................................................58 2.2.2 MDI/Editing Related.....................................................................................................................59 2.2.3 Data Input/Output Related...........................................................................................................60 2.2.4 S-analog Output Adjustment Related..........................................................................................61 2.2.5 Auxiliary Axis ...............................................................................................................................61 2.2.6 Parameter Backup Related .........................................................................................................61 2.2.7 Others ..........................................................................................................................................62

3. Program Error ........................................................................................................................................63

II EXPLANATION OF PARAMETERS

1. Screen Configuration ..............................................................................................................................1 1.1 Screen Transition Charts .....................................................................................................................1

2. Machining Parameters.............................................................................................................................3 2.1 Process Parameters.............................................................................................................................3 2.2 Control Parameters ............................................................................................................................10 2.3 Axis Parameters .................................................................................................................................12 2.4 Barrier Data ........................................................................................................................................14 2.5 Tool Measurement Parameters..........................................................................................................16

3. I/O Parameters........................................................................................................................................17 3.1 Base Parameters................................................................................................................................17 3.2 I/O Device Parameters .......................................................................................................................18 3.3 Computer Link Parameters ................................................................................................................20

4. Setup Parameters ..................................................................................................................................22

5. Base Specifications Parameters ..........................................................................................................23

6. Axis Specifications Parameters ...........................................................................................................92 6.1 Axis Specifications Parameters..........................................................................................................92 6.2 Zero Point Return Parameters ...........................................................................................................99 6.3 Absolute Position Parameters..........................................................................................................102 6.4 Axis Specification Parameters 2 ......................................................................................................104

7. Servo Parameters ................................................................................................................................112 7.1 MDS-B-SVJ2 ....................................................................................................................................114 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)............................................................................141 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible) .........................................................169 7.4 Supplement ......................................................................................................................................199

7.4.1 D/A Output Specifications..........................................................................................................199 7.4.2 Electronic Gears ........................................................................................................................205 7.4.3 Lost Motion Compensation........................................................................................................207

8. MDS-B-SP/SPH, SPJ2 Spindle Parameters .......................................................................................208 8.1 MDS-B-SP/SPH, SPJ2 Spindle Base Specifications Parameters ...................................................208 8.2 MDS-B-SPJ2 ....................................................................................................................................216 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH.................................................................................................236 8.4 MDS-C1-SPM...................................................................................................................................269 8.5 Supplement ......................................................................................................................................302

8.5.1 D/A Output Specifications..........................................................................................................302

9. Machine Error Compensation.............................................................................................................305 9.1 Function Outline ...............................................................................................................................305 9.2 Setting Compensation Data .............................................................................................................309 9.3 Example in Using a Linear Axis as the Base Axis ...........................................................................311 9.4 Example in Using a Rotation Axis as the Base Axis ........................................................................315

10. PLC Constants ...................................................................................................................................316 10.1 PLC Timer ......................................................................................................................................316 10.2 PLC Counter...................................................................................................................................316 10.3 PLC Constants ...............................................................................................................................317 10.4 Selecting the PLC Bit .....................................................................................................................317

11. Macro List ...........................................................................................................................................320

12. Position Switch ..................................................................................................................................322 12.1 Outline of Function .........................................................................................................................322 12.2 Canceling the Position Switch........................................................................................................324

13. Auxiliary Axis Parameter ..................................................................................................................325

I EXPLANATION OF ALARMS

1. List of Alarms 1.1 Operation Alarms

I - 1

1. List of Alarms

1.1 Operation Alarms

(The bold characters are the messages displayed on the screen.)

M01 OPERATION ERROR Alarms occurring due to incorrect operation by the operator during NC operation and those by machine trouble are displayed.

Error No. Details Remedy

0001 DOG OVERRUN (Dog overrun) When returning to the reference point the near-point detection limit switch did not stop over the dog but overran the dog.

Increase the length of the near-point dog.

Reduce the reference point return speed.

0002 Z-AX NO CRSS One of the axes did not pass the Z-phase during the initial reference point return after the power was turned ON.

Move the detector one rotation or more in the opposite direction of the reference point and repeat reference point return.

0003 INVALID RET (Invalid return) When manually returning to the reference point the return direction differs from the axis movement direction selected with the AXIS SELECTION key.

The selection of the AXIS SELECTION keys +/ direction is incorrect. The error is canceled by feeding the axis in the correct direction.

0004 EXT INTRLK (External interlock) The external interlock function has activated (the input signal is "OFF") and one of the axes has entered the interlock state.

As the interlock function has activated release it before resuming operation.

Check the sequence on the machine side.

Check for broken wires in the interlock signal line.

0005 INTRL INTRLK (Internal interlock) The internal interlock state has been entered. The absolute position detector axis has been removed. A command for the manual/automatic simultaneous valid axis was issued from the automatic mode.

The servo OFF function is valid so release it first.

An axis that can be removed has been issued so perform the correct operations.

The command is issued in the same direction as the direction where manual skip turned ON so perform the correct operations.

During the manual/automatic simul- taneous mode the axis commanded in the automatic mode became the manual operation axis. Turn OFF the manual/ automatic valid signal for the commanded axis.

Turn ON the power again and perform absolute position initialization.

1. List of Alarms 1.1 Operation Alarms

I - 2

Error No. Details Remedy

0006 H/W STRK END (H/W stroke end) The stroke end function has activated (the input signal is "OFF") and one of the axes is in the stroke end status.

Move the machine manually. Check for broken wires in the stroke end

signal wire. Check for trouble in the limit switch.

0007 S/W STRK END (S/W stroke end) The stored stroke limit I II IIB or IB function has activated.

Move it manually. If the stored stroke limit in the parameter

is incorrectly set correct it.

0008 Chuck/tail-stock barrier stroke end axis found

The chuck/tail-stock barrier function turned ON and an axis entered the stroke end state.

Reset the alarm with reset and move the machine in the reverse direction.

0009 Reference point return number illegal Return to the No. 2 reference point was performed before return to the No. 1 reference point was completed.

Execute No. 1 reference point return.

0019 Sensor signal illegal ON The sensor signal was already ON when the tool measurement mode (TLM) signal was validated.

The sensor signal turned ON when there was no axis movement after the tool measurement mode (TLM) signal was validated.

The sensor signal turned ON at a position within 100m from the final entry start position.

Turn the tool measurement mode signal input OFF, and move the axis in a safe direction.

The operation alarm will turn OFF even when the sensor signal is turned OFF.

Note) When the tool measurement mode signal input is turned OFF, the axis can be moved in either direction. Pay attention to the movement direction.

0020 Reference point return illegal Return to the reference point was performed before the coordinates had not been established.

Execute reference point return

0024 Zero point return disabled during absolute position detection alarm

A zero point return signal was input during an absolute position detection alarm.

Reset the absolute position detection alarm and then perform zero point return.

0025 Zero point return disabled during zero point initialization

A zero point return signal was input during zero point initialization of the absolute position detection system.

Complete zero point initialization and then perform zero point return.

1. List of Alarms 1.1 Operation Alarms

I - 3

Error No. Details Remedy

0050 Chopping axis zero point return incomplete

The chopping axis has not completed zero point return before entering the chopping mode. All axes interlock will be applied.

Reset or turn the chopping signal OFF, and then carry out zero point return.

0051 Synchronization error too large The synchronization error of the master and slave axes exceeded the allowable value under synchronous control.

A deviation exceeding the synchroni- zation error limit value was found with the synchronization deviation detection.

Select the correction mode and move one of the axes in the direction in which the errors are reduced.

Increase the allowable value or reset it to 0 (check disabled).

When using simple C-axis synchronous control, set the contents of the R435 register to 0.

Check the parameter (#2024 synerr).

0101 NOT OP MODE (Not operation mode) Check for a broken wire in the input mode signal wire.

Check for trouble in the mode selector switch.

Check the sequence program.

0102 OVERRIDE ZERO (Override zero) The cutting feed override switch on the machine operation panel is set to zero.

Set "the cutting feed override" switch to a value other than zero to release the error.

If "the cutting feed override" switch is set to a value other than zero check for a short circuit in the signal wire.

Check the sequence program.

0103 EX F SPD ZRO (External feed speed zero)

The manual feed speed switch on the machine operation panel is set to zero when the machine is in the jog mode or automatic dry run mode.

The "Manual feedrate B speed" is set to zero during the jog mode when manual feedrate B is valid.

The "each axis manual feedrate B speed" is set to zero during the jog mode when each axis manual feedrate B is valid.

Set "the manual feed speed" switch to a value other than zero to release the error.

If the manual feed speed switch is set to a value other than zero check for a short circuit in the signal wire.

Check the sequence program.

0104 F1 SPD ZRO (F1-digit speed zero) The F1-digit feedrate is set to zero when the F1-digit feed command is being executed.

Set the F1-digit feedrate on the setup parameter screen.

1. List of Alarms 1.1 Operation Alarms

I - 4

Error No. Details Remedy

0105 SPINDLE STP (Spindle stop) The spindle stopped during the synchronous feed command.

Rotate the spindle. If the workpiece is not being cut start dry

run. Check for a broken wire in the spindle

encoder cable. Check the connections for the spindle

encoder connectors. Check the spindle encoder pulse.

0106 HNDL FD NOW (Handle feed axis No. illegal)

An axis not found in the specifications was designated for handle feed or the handle feed axis was not selected.

Check for broken wires in the handle feed axis selection signal wire.

Check the sequence program. Check the No. of axes listed in the

specifications.

0107 SPDL RPM EXS (Spindle rotation speed excessive)

The spindle rotation speed exceeded the axis clamp speed during the thread cutting command.

Lower the commanded spindle rotation speed.

0108 Fixed point mode feed axis No. illegal: An axis not found in the specifications was designated for the fixed point mode feed or the fixed point mode feedrate is illegal.

Check for broken wires in the fixed mode feed axis selection signal wire and fixed point mode feedrate wire.

Check the fixed point mode feed specifications.

0109 BLK ST INTLK (Block start interlock) An interlock signal that locks the start of the block has been input.

Check the sequence program.

0110 CTBL ST INTLK (Cutting block start interlock)

An interlock signal that locks the start of the cutting block has been input.

Check the sequence program.

0111 Restart switch ON The restart switch was turned ON before the restart search was completed, and the manual mode was selected.

Search the block to be restarted. Turn OFF the restart switch.

0112 Program Check Mode The automatic start button was pressed during program check or in program check mode.

Press the reset button to cancel the program check mode.

0113 Automatic start during buffer correction The automatic start button was pressed during buffer correction.

Press the automatic start button after buffer correction is completed.

1. List of Alarms 1.1 Operation Alarms

I - 5

Error No. Details Remedy

0115 RESETTING The automatic start button was pressed during resetting or tape rewinding.

When rewinding the tape wait for the winding to end or press the reset button to stop the winding and then press the automatic start button.

During resetting wait for resetting to end and then press the automatic start button.

0117 PLAYBACK NOT POSSIBLE The playback switch was turned ON during editing or full-character mode (9-inch).

During editing cancel the function by pressing the input or previous screen key and then turn ON the playback switch.

Set the edit screen (9-inch) to the half-character mode and then turn ON the playback switch.

0118 Block joint turn stop during normal line control

The turning angle at the block joint exceeded the limit during normal line control.

Normal line control type I The normal line control axis turning speed (#1523 C_feed) has not been set.

Normal line control type II When turning in the inside of the arc, the parameter #8041 C-rot. R setting value is larger than the arc radius.

Check the program. Set the normal line control axis turning

speed. (Parameter #1523 C_feed) Set the C axis turning diameter smaller

than the arc radius, or check the setting value of the C axis turning diameter. (Parameter #8041 C rot. R)

0120 Synchronization correction mode ON The synchronous correction mode switch was pressed in a non-handle mode.

Select the handle or manual feed mode. Turn OFF the correction mode switch.

0121 No synchronous control option The synchronous control system (register R435) was set with no synchronous control option.

Set 0 in register R435.

0123 Computer link B The cycle start was attempted before resetting was completed.

The operation of the computer link B was attempted in the 2nd part system of the 2-part system.

Perform the cycle start after resetting is completed.

Set 0 in #8109 HOST LINK, and then set 1 again before performing the cycle start.

The operation of the computer link B cannot be performed in the 2nd part system of the 2-part system.

0124 Simultaneous axis movement prohibited during inclined axis control valid

The basic axis corresponding to the inclined axis was started simultaneously in the manual mode while the inclined axis control was valid.

Turn the inclined axis and basic axis start OFF for both axes. (This also applied for manual/automatic simultaneous start.)

Invalidate the basic axis compensation, or command one axis at a time.

1. List of Alarms 1.1 Operation Alarms

I - 6

Error No. Details Remedy

0126 Program restart machine lock Machine lock was applied on the return axis while manually returning to the restart position.

Release the machine lock before resuming operations.

0150 Chopping override zero Check the chopping override (R135). Check the rapid traverse override (R134).

0151 Command axis chopping axis A chopping axis movement command was issued from the program during the chopping mode. (This alarm will not occur when the movement amount is commanded as 0.) (All axes interlock state will be applied.)

Reset, or turn OFF the chopping signal. When the chopping signal is turned OFF, the axis will return to the reference position, and then the program movement command will be executed.

0153 Bottom dead center position zero The bottom dead center position is set to the same position as the upper dead center position.

Correctly set the bottom dead center position.

0154 Chopping axis handle selection axis Chopping was started when the chopping axis was selected as the handle axis.

Select an axis other than the chopping axis as the handle axis, or start chopping after changing the mode to another mode.

0160 Axis with no maximum speed set for the outside of the soft limit range

Returned from the outside of the soft limit range for the axis with no maximum speed set for the outside of the soft limit range.

Set the maximum speed for the outside of the soft limit range. (Parameter #2021 out_f)

Change the soft limit range. (Parameter #2013 OT #2014 OT+)

1005 An attempt was made to execute G114.* during execution of G114.*.

G51.2 was commanded when the G51.2 spindle-spindle polygon machining mode was already entered with a separate system.

Issue G113 to cancel G114.*. Issue the spindle synchronous cancel

signal (Y2E8: SPSYC) to cancel G114.*. Cancel with G50.2. Cancel with the spindle-spindle polygon

cancel signal (Y359).

1007 The spindle is being used in synchronized tapping.

Cancel synchronized tapping.

1026 Spindle C axis and other position control were commanded simultaneously.

C axis mode command was issued for polygon machining spindle.

C axis mode command was issued for synchronized tapping spindle.

Polygon command was issued for synchronized tapping spindle.

Spindle is being used as spindle/C axis.

Cancel the C axis command. Cancel the polygon machining command. Cancel the C axis with servo OFF.

1. List of Alarms 1.1 Operation Alarms

I - 7

Error No. Details Remedy

1030 Synchronization mismatch Different M codes were commanded in the two systems as the synchronization M codes.

Synchronization with the "!" code was commanded in another system during M code synchronization.

Synchronization with the M code was commanded in another system during synchronization with the "!" code.

Correct the program so that the M codes match.

Correct the program so that the same synchronization codes are commanded.

1031 The C axis selection signal was changed when multiple C axes could not be selected.

An axis that cannot be controlled as the multiple C axes selection was selected.

Check and correct the parameters and program.

1032 Tap return spindle selection illegal during multi-spindle

Tap return was executed when a different spindle was selected. Cutting feed will wait until synchronization is completed.

Select the spindle for which tap cycle was halted before the tap return signal was turned ON.

1033 Spindle-spindle polygon (G51.2) cutting interlock

Cutting feed will wait until synchronization is completed.

Wait for synchronization to end.

1034 Cross machining command illegal Cross machining control exceeding the number of control axes was attempted.

Cross machining control with duplicated axis addresses was attempted.

Check the parameter settings for cross machining control.

1035 Cross machining control disable modal Cross machining control was commanded for a system in which cross machining control is disabled as shown below.

During nose R compensation mode During pole coordinate interpolation

mode During cylindrical interpolation mode During balance cut mode During fixed cycle machining mode During facing turret mirror image

Check the program.

1. List of Alarms 1.1 Operation Alarms

I - 8

Error No. Details Remedy

1036 Synchronous control designation disable The synchronous control operation method selection (R435 register) was set when the mode was not the C axis mode.

The synchronous control operation method selection (R435 register) was set in the zero point not set state.

Mirror image disable state The external mirror image or parameter mirror image was commanded during facing turret mirror image.

Set the R435 register to 0.

Check the program and parameters.

1037 Synchronous control was started or canceled when synchronous control could not be started or canceled.

Check the program and parameters.

1038 A movement command was issued to a synchronous axis in synchronous control.

Check the program.

1043 No spindle speed clamp The constant surface speed command (G96) was issued to the spindle which is not selected for the spindle speed clamp command (G92/G50) under Multiple spindle control II.

Press the reset key and carry out the remedy below.

Select the spindle before commanding G92/G50.

(Applicable only to M65 V series and M64 C

version series)

1106 Spindle synchronous phase calculation illegal

The spindle synchronization phase alignment command was issued while the spindle synchronization phase calculation request signal was ON.

Check the program. Check the sequence program.

(The bold characters are the messages displayed on the screen.)

M90 PARAM SET MODE M90 Messages output when the setup parameter lock function is enabled are displayed.

Error No. Details Remedy

Setup parameter lock released The setup parameter lock is released. Automatic start is disabled when setup parameters can be set.

Refer to the manual issued by the machine manufacturer.

1. List of Alarms 1.2 Stop Codes

I - 9

1.2 Stop Codes

These codes indicate a status that caused the controller to stop for some reason. (The bold characters are the messages displayed on the screen.)

T01 CANT CYCLE ST This indicates the state where automatic operation cannot be started when attempting to start it from the stop state.

Error No. Details Remedy

0101 AX IN MOTION (axis in motion) Automatic start is not possible as one of the axes is moving.

Try automatic start again after all axes have stopped.

0102 READY OFF Automatic start is not possible as the NC is not ready.

Another alarm has occurred. Check the details and remedy.

0103 RESET ON Automatic start is not possible as the reset signal has been input.

Turn OFF the reset input signal. Check that the reset switch is not ON

constantly due to trouble. Check the sequence program.

0104 A-OP STP SGL (Automatic operation stop signal ON)

The FEED HOLD switch on the machine operation panel is ON (valid).

Check the FEED HOLD switch. The feed hold switch is the B contact. Check for broken wires in the feed hold

signal wire. Check the sequence program.

0105 H/W STRK END (H/W stroke end axis) Automatic start is not possible as one of the axes is at the stroke end.

If one of the axis ends is at the stroke end move the axis manually.

Check for broken wire in the stroke end signal wire.

Check for trouble in the stroke end limit switch.

0106 S/W STRK END (S/W stroke end axis) Automatic start is not possible as one of the axes is at the stored stroke limit.

Move the axis manually. If an axis is not at the end check the

parameter details.

0107 NO OP MODE (NO operation mode) The operation mode has not been selected.

Select the automatic operation mode. Check for broken wires in the automatic

operation mode (memory tape MDl) signal wire.

1. List of Alarms 1.2 Stop Codes

I - 10

Error No. Details Remedy

0108 OP MODE DUPL (Operation mode duplicated)

Two or more automatic operation modes are selected.

Check for a short circuit in the mode selection signal wire (memory tape MDl).

Check for trouble in the switch. Check the sequence program.

0109 OP MODE SHFT (Operation mode shift) The automatic operation mode changed to another automatic operation mode.

Return to the original automatic operation mode and start automatic start.

0110 Tape search execution Automatic start is not possible as tape search is being executed.

Begin automatic start after the tape search is completed.

0112 Program restart position return incomplete Automatic start is not possible as the axis has not been returned to the restart position.

Manually return to the restart position. Turn the automatic restart valid

parameter ON, and then execute automatic start.

0113 Thermal alarm Automatic start is not possible because a thermal alarm (Z53 TEMP. OVER) has occurred.

The NC controller temperature has exceeded the specified temperature.

Take appropriate measures to cool the unit.

0115 In host communication Automatic start cannot be executed as the NC is communicating with the host computer.

Execute automatic start after the communication with the host computer is completed.

0138 Disabled start during absolute position detection alarm

A start signal was input during an absolute position detection alarm.

Reset the absolute position detection alarm and then input the start signal.

0139 Disabled start during zero point initialization

A start signal was input while initializing the absolute position detectors zero point.

Complete zero point initialization before inputting the start signal.

0190 Automatic start disabled Automatic start is disabled because setup parameters can be set.

Refer to the manual issued by the machine manufacturer.

0191 Automatic start disabled Automatic start was caused during file deletion or writing.

Cause automatic start after file deletion or writing is completed.

1. List of Alarms 1.2 Stop Codes

I - 11

T02 FEED HOLD The feed hold state been entered due to a condition in the automatic operation.

Error No. Details Remedy

0201 H/W STRK END (H/W stroke end axis) An axis is at the stroke end.

Manually move the axis away from the stroke end limit switch.

The machining program must be corrected.

0202 S/W STRK END (S/W stroke end axis) An axis is at the stored stroke limit.

Manually move the axis. The machining program must be

corrected.

0203 RESET SIGNAL ON (Reset signal on) The reset signal has been input.

The program execution position has returned to the start of the program. Execute automatic operation from the start of the machining program.

0204 AUTO OP STOP (Automatic operation stop)

The FEED HOLD switch is ON.

Resume automatic operation by pressing the CYCLE START switch.

0205 AUTO MD CHING (Automatic mode change)

The operation mode changed to another mode during automatic operation.

Return to the original automatic operation mode and resume automatic operation by pressing the CYCLE START switch.

0206 Acceleration and deceleration time constants too large

The acceleration and deceleration time constants are too large. (This problem occurs at the same time as system alarm Z59.)

Increase the set value of the parameter #1206 G1bF.

Decrease the set value of the parameter #1207 G1btL.

Lower the cutting speed.

0215 Absolute position detection alarm stop An absolute position detection alarm occurred.

Reset the absolute position detection alarm.

1. List of Alarms 1.2 Stop Codes

I - 12

T03 BLOCK STOP This indicates that automatic operation stopped after executing one block of the program.

Error No. Details Remedy

0301 SNGL BLK ON (Single block on) The SINGLE BLOCK switch on the machine operation panel is ON.

The single block or machine lock switch changed.

Automatic operation can be resumed by turning the CYCLE START switch ON.

0302 User macro stop The block stop command was issued in the user macro program.

Automatic operation can be resumed by turning the CYCLE START switch ON.

0303 Mode change The automatic mode changed to another automatic mode.

Return to the original automatic operation mode and resume automatic operation by turning the CYCLE START switch ON.

0304 MDI completion The last block of MDI was completed.

Set MDI again and turn the CYCLE START switch ON to resume MDl operation.

0305 Block start interlock The interlock signal that locks the block start is entered.

Check the sequence program.

0306 Block cutting start interlock The interlock signal that locks the block cutting start is entered.

Check the sequence program.

0310 Offset change of inclined Z-axis during program operation

Whether to validate the offset of the inclined Z-axis switched during program operation.

Automatic operation can be restarted by turning ON the cycle start switch.

T04 COLLATION STOP Collation stop was applied during automatic operation.

Error No. Details Remedy

0401 Collation stop occurred. Automatic operation can be restarted with automatic start.

1. List of Alarms 1.2 Stop Codes

I - 13

T10 FIN WAIT This indicates the operation state when an alarm did not occur during automatic operation and nothing seems to have happened.

Error No. Details

0 The error number is displayed while each of the completion wait modes listed in the table below is ON. It disappears when the mode is canceled.

0

Alarm No.

Unclamp signal wait Note 2)

In dwell execu- tion

Alarm No.

Door open Note 1)

Waiting for spindle position to be looped

Alarm No.

Waiting for spindle orienta- tion to complete

Waiting for cutting speed decelera- tion

Waiting for rapid traverse decelera- tion

Waiting for MSTB comp- letion

0 0 0

1 1 1

8 8 2

9 9 3

4

5

6

7

8

9

A

B

C

D

E

F Note 1: This mode is enabled by the door interlock function. Note 2: The system is waiting for the index table indexing unclamp signal to turn

ON or OFF

1. List of Alarms 1.3 Servo spindle Alarms

I - 14

1.3 Servo/Spindle Alarms

This section describes alarms occurred by the errors in the servo system such as the drive unit motor and encoder, etc. The alarm message alarm No. and axis name will display on the alarm message screen. The axis where the alarm occurred and the alarm No. will also display on the servo monitor screen and the spindle monitor screen respectively. If several alarms have occurred up to two errors per axis will display on the servo monitor screen and the spindle monitor screen respectively. (The bold characters are the messages displayed on the screen.)

S SERVO ALARM : 0 0 Axis name

Alarm No.

Alarm reset class

Alarm class

Servo : Axis name

Spindle : S, T, M, N

(Note 1) The alarm class and alarm reset class combinations are preset. (Refer to the separate table for S02, S51 and S52.)

Alarm class Alarm reset class Resetting methods S01 PR After removing the cause of the alarm, reset the

alarm by turning the NC power ON again.

S03 NR After removing the cause of the alarm, reset the alarm by inputting the NC RESET key.

S04 AR After removing the cause of the alarm, reset the alarm by turning the drive unit power ON again.

(Note 2) The resetting method may change according to the alarm class. For example, even if S03 SERVO ALARM: NR is displayed, it may be necessary to turn the NC

power ON again. Alarm No. Name Meaning

10 Insufficient voltage Insufficient PN bus voltage was detected in main circuit. 11 Axis selection error Setting of the axis No. selection switch is incorrect. 12 Memory error 1 A CPU error or an internal memory error was detected during the

power ON self-check. 13 Software processing

error 1 Software processing has not finished within the specified time.

14 Software processing error 2

Software processing has not finished within the specified time.

15 Memory error 2 A CPU error or an internal memory error was detected during the power ON self-check.

16 Magnetic pole position detection error

Initial magnetic pole for motor control has not been formed yet.

17 A/D converter error An error was detected in the A/D converter for detecting current FB. 18 Motor side detector:

Initial communication error

Initial communication with the motor end detector failed.

19 Detector communication error in synchronous control

Initial communication with the motor end detector on master axis failed when setting closed-loop current synchronous control. Or the communication was interrupted.

1. List of Alarms 1.3 Servo spindle Alarms

I - 15

Alarm No. Name Meaning

1A Machine side detector: Initial communication error

Initial communication with the linear scale or the ball screw end detector failed.

1B Machine side detector: CPU error 1

CPU initial error was detected in the linear scale or in the ball screw end detector.

1C Machine side detector: EEPROM/LED error

An error was detected in the stored data of the linear scale memory. Or the LED deterioration was detected in the ball screw end detector.

1D Machine side detector: Data error

An error data was detected in the linear scale or in the ball screw end detector.

1E Machine side detector: Memory error

An internal memory error was detected in the linear scale.

1F Machine side detector: Communication error

An error was detected in communication data with the linear scale or the ball screw end detector. Or the communication was interrupted.

20 Motor side detector: No signal

No signals were detected in A,B,Z-phase or U,V,W-phase of the pulse motor end detector in a servo system, or in Z-phase of PLG in a spindle system.

21 Machine side detector: No signal

No signals were detected in A,B,Z-phase of the pulse linear scale or the ball screw end detector in a servo system. Or no encoder signals were detected in a spindle system.

22 LSI error LSI operation error was detected in the drive unit. 23 Excessive speed

error 1 A difference between the speed command and speed feedback was continuously exceeding 50 r/min for longer than the setting time.

24 Grounding The motor power cable is in contact with FG (Frame Ground). 25 Absolute position

data lost The absolute position was lost, as the backup battery voltage dropped in the absolute position detector.

26 Unused axis error A power module error occurred in the axis whose axis No. selection switch was set to "F"(free axis).

27 Machine side detector: CPU error 2

A CPU error was detected in the linear scale.

28 Machine side detector: Overspeed

The specified max. speed was detected in the linear scale.

29 Machine side detector: Absolute position data error

An error was detected in the absolute position detection circuit of the linear scale.

2A Machine side detector: Relative position data error

An error was detected in the relative position detection circuit of the linear scale.

2B Motor side detector: CPU error 1

A CPU initial error was detected in the motor end detector or in the linear scale of a linear servo system.

2C Motor side detector: EEPROM/LED error

The LED deterioration was detected in the motor end detector. Or an error was detected in the stored data of the linear scale memory of a linear servo system.

1. List of Alarms 1.3 Servo spindle Alarms

I - 16

Alarm No. Name Meaning 2D Motor side detector:

Data error A data error was detected in the motor end detector or in the linear scale of a linear servo system.

2E Motor side detector: Memory error

An internal memory error was detected in the linear scale of a linear servo system.

2F Motor side detector: Communication error

An error was detected in communication data with the motor end detector or with the linear scale of a linear servo system. Or the communication was interrupted.

30 Over regeneration Over-regeneration detection level became over 100%. The regenerative resistor is overloaded.

31 Overspeed The motor was detected to rotate at a speed exceeding the allowable speed.

32 Power module overcurrent

Overcurrent protection function in the power module has started its operation.

33 Overvoltage PN bus voltage in main circuit exceeded the allowable value. 34 NC-DRV

communication: CRC error

An error was detected in the data received from the CNC.

35 NC command error The travel command data that was received from the CNC was excessive.

36 NC-DRV communication: Communication error

The communication with the CNC was interrupted.

37 Initial parameter error

An incorrect parameter was detected among the parameters received from the CNC at the power ON.

38 NC-DRV communication: Protocol error 1

An error was detected in the communication frames received from the CNC.

39 NC-DRV communication: Protocol error 2

An error was detected in the axis information data received from the CNC.

3A Overcurrent Excessive current was detected in the motor drive current. 3B Power module

overheat Thermal protection function in the power module has started its operation.

3C Regeneration circuit error

An error was detected in the regenerative transistor or in the regenerative resistor.

3D Spindle speed blocked

The spindle motor failed to rotate faster than 45 r/min, even when the max. torque command was given.

3E Spindle speed overrun

1. The spindle motor speed feedback was detected to be accelerated exceeding the commanded speed. 2. The spindle motor was detected to be rotated at a speed exceeding the parameter value, while the speed command was "0" (including the case of operation stoppage during the position control).

3F Excessive speed error 2

A difference between the speed command and speed feedback was detected to exceed the setting amount or setting time in a constant speed operation.

1. List of Alarms 1.3 Servo spindle Alarms

I - 17

Alarm No. Name Meaning

40 Detector selection unit switching error

An error was detected in the motor switching signals that were received from the detector selection unit, while controlling one drive unit and two motors.

41 Detector selection unit communication error

An error was detected in the communication with the detector selection unit, while controlling one drive unit and two motors.

42 Feedback error 1 An error was detected in the feedback signals of the pulse motor end detector in a servo system, or in PLG's feedback signals in a spindle system.

43 Feedback error 2 Excessive difference was detected in position data between the motor end detector and the machine end detector in a servo system. In a spindle system, an error was detected in the encoder feedback signals.

44 Inappropriate coil selected for C axis

When using a coil changeover motor, C-axis was controlled while the high-speed coil was selected.

45 Fan stop A cooling fan built in the drive unit stopped, and the loads on the unit exceeded the specified value.

46 Motor overheat Thermal protection function of the motor or in the detector, has started its operation.

47 Regenerative resistor overheat

Thermal protection function of the regenerative resistor, has started its operation.

48 Motor side detector: CPU error 2

A CPU error was detected in the linear scale of a linear servo system.

49 Motor side detector: Overspeed

The specified max. speed was detected in the linear scale of the linear servo system.

4A Motor side detector: Absolute position data error

An error was detected in the absolute position detection circuit in the linear scale of a linear servo system.

4B Motor side detector: Relative position data error

An error was detected in the relative position detection circuit in the linear scale of a linear servo system.

4C Current error at magnetic pole detection

A current error was detected in the IPM spindle motor when the initial magnetic pole was being formed.

4E NC command mode error

The mode outside the specification was input in spindle control mode selection.

4F Instantaneous power interruption

The power was momentarily interrupted.

50 Overload 1 Overload detection level became over 100%. The motor or the drive unit is overloaded.

51 Overload 2 Current command of more than 95% of the unit's max. current was being continuously given for longer than 1 second in a servo system. In a spindle system, the load over the continuous rating was being applied for longer than 30 minutes.

52 Excessive error 1 A difference between the actual and theoretical motor positions during servo ON exceeded the setting value in a servo system. In a spindle system, a difference between the position command and position feedback exceeded the setting value.

1. List of Alarms 1.3 Servo spindle Alarms

I - 18

Alarm No. Name Meaning

53 Excessive error 2 A difference between the actual and theoretical motor positions during servo OFF exceeded the setting value.

54 Excessive error 3 When an excessive error 1 occurred, detection of the motor current failed.

55 External emergency stop error

There is no contactor shutoff command, even after 30 seconds has passed since the external emergency stop was input.

57 Option error An invalid option function was selected. 58 Collision detection 1:

G0 When collision detection function was valid, the disturbance torque in rapid traverse (G0) exceeded the collision detection level.

59 Collision detection 1: G1

When collision detection function was valid, the disturbance torque in cutting feed (G1) exceeded the collision detection level.

5A Collision detection 2 When collision detection function was valid, the command torque reached the max. motor torque.

5C Orientation feedback error

After orientation was achieved, a difference between the command and feedback exceeded the parameter setting.

5D Speed monitoring: Input mismatch

As for door state signal of speed monitoring control, a mismatch between the external input signal and the control signal received from the CNC was detected.

5E Speed monitoring: Feedback speed error

In speed monitoring control, the spindle speed was exceeding the setting speed with the door open.

5F External contactor error

A contact of the external contactor is welding. Or the contactor fails to be ON during ready ON.

61 Power module overcurrent

Overcurrent protection function in the power module has started its operation.

62 Frequency error The input power supply frequency increased above the specification range.

63 Supplementary regeneration error

The supplementary regenerative transistor is being ON.

65 Rush relay error A resistor relay for rush short circuit fails to be ON. 67 Phase interruption An open-phase condition was detected in input power supply circuit. 68 Watchdog The system does not operate correctly. 69 Grounding The motor power cable is in contact with FG (Frame Ground). 6A External contactor

welding A contact of the external contactor is welding.

6B Rush relay welding A resistor relay for rush short circuit fails to be OFF. 6C Main circuit error An error was detected in charging operation of the main circuit

capacitor. 6D Parameter error The capacity of the power supply unit and the regenerative resistor

type that was set in the parameter are mismatched. 6E Memory error An internal memory error was detected. 6F Power supply error A power supply unit is not connected. Or an error was detected in

A/D converter of the power supply unit. 71 Instantaneous

power interruption The power was momentarily interrupted.

1. List of Alarms 1.3 Servo spindle Alarms

I - 19

Alarm No. Name Meaning

73 Over regeneration Over-regeneration detection level became over 100%. The regenerative resistor is overloaded.

74 Regenerative resistor overheat

Thermal protection function of the regenerative resistor, has started its operation.

75 Overvoltage PN bus voltage in main circuit exceeded the allowable value. 76 External emergency

stop setting error As for the external emergency stop settings, the setting on the rotary switch and the parameter setting are mismatched.

77 Power module overheat

Thermal protection function in the power module has started its operation.

7F Drive unit power supply restart request

A mismatch of program mode selection was detected. Turn the drive unit power ON again.

80 Detector converting unit 1: Connection error

A connection error was detected between the analog output linear scale and the unit MDS-B-HR that is used in a linear servo system.

81 Detector converting unit 1: Communication error

A communication error was detected between the serial output linear scale and the unit MDS-B-HR that is used in a linear servo system.

83 Detector converting unit 1: Judgment error

Judgment of the linear scale analog frequency failed in the unit MDS-B-HR that is used in a linear servo system.

84 Detector converting unit 1: CPU error

A CPU error was detected in the unit MDS-B-HR that is used in a linear servo system.

85 Detector converting unit 1: Data error

A data error was detected in the unit MDS-B-HR that is used in a linear servo system.

86 Detector converting unit 1: Magnetic pole error

An error was detected in the magnetic pole of the unit MDS-B-HR that is used in a linear servo system.

88 Watchdog The system does not operate correctly. 89 Detector converting

unit 2: Connection error

A connection error was detected between the analog output linear scale and the unit MDS-B-HR in a servo system. In a spindle system, the initial communication with MDS-B-PJEX failed.

1. List of Alarms 1.3 Servo spindle Alarms

I - 20

Alarm No. Name Meaning

8A Detector converting unit 2: Communication error

An error was detected in the communication with the serial output linear scale of the unit MDS-B-HR in a servo system. In a spindle system, an error was detected in the communication with MDS-B-PJEX.

8B Detector converting unit 2: Automatic tuning error

An abnormal signal was detected from PLG in automatic PLG tuning.

8C Detector converting unit 2: Judgment error

The detector type outside the specification was designated in MDS-B-PJEX.

8D Detector converting unit 2: CPU error

A CPU error was detected in the unit MDS-B-HR in a servo system, or in the unit MDS-B-PJEX in a spindle system.

8E Detector converting unit 2: Data error

A data error was detected in the unit MDS-B-HR.

S02 INIT PARAM ERR

Axis name

Alarm No. (parameter No.)

Servo : Axis name

Spindle : S, T, M, N

An error was found in the parameters transmitted from the controller to the drive unit when the power was turned ON. Remove the cause of the alarm, and then reset the alarm by turning the controller power OFF once.

Alarm No. Details Remedy

2201 - 2264 The servo parameter setting data is illegal. The alarm No. is the No. of the servo parameter where the error occurred.

Check the descriptions for the appropriate servo parameters and correct them.

2301 The number of constants to be used in the following functions is too large: Electronic gears Position loop gain Speed feedback conversion

Check that all the related parameters are specified correctly. sv001:PC1, sv002:PC2, sv003:PGN1 sv018:PIT, sv019:RNG1, sv020:RNG2

2302 High-speed serial incremental detector Parameters for absolute position detection are set to ON during OSE104 and OSE105 connection. Set the parameters for absolute position detection to OFF. To detect an absolute position, replace the incremental specification detector with an absolute position detector.

Check that all the related parameters are specified correctly. sv017:SPEC, sv025:MTYP

2303 No servo option is found. The closed loop (including the ball screw- end detector) or dual feedback control is an optional function.

Check that all the related parameters are specified correctly. sv025:MTYP/pen sv017:SPEC/dfbx

1. List of Alarms 1.3 Servo spindle Alarms

I - 21

Alarm No. Details Remedy

2304 No servo option is found. The SHG control is an optional function.

Check that all the related parameters are specified correctly. sv057:SHGC sv058:SHGCsp

2305 No servo option is found. The adaptive filtering is an optional function.

Check that all the related parameters are specified correctly. sv027:SSF1/aflt

3201 - 3584 The spindle parameter setting data is illegal. The alarm No. is the No. of the spindle parameter where the error occurred.

Check the descriptions for the appropriate spindle parameters and correct them. Refer to Spindle Drive Maintenance Manual.

1. List of Alarms 1.3 Servo spindle Alarms

I - 22

S51 PARAMETER ERROR

Axis name

Alarm No. (parameter No.)

Servo : Axis name

Spindle : S, T, M, N

Warning appears if a parameter set outside the tolerable range is set. Illegal settings will be ignored. This alarm will be reset when the correct value is set.

Alarm No. Details Remedy

2201 - 2264 Servo parameter setting data is illegal. The alarm No. is the No. of the servo parameter where the warning occurred.

Check the descriptions for the appropriate servo parameters and correct them.

3201 - 3584 Spindle parameter setting data is illegal. The alarm No. is the No. of the spindle parameter where the warning occurred.

Check the descriptions for the appropriate spindle parameters and correct them. Refer to Spindle Drive Maintenance Manual.

S52 SERVO WARNING 0 0

Axis name

Alarm No. (Warning No.)

Servo : Axis name

Spindle : S, T, M, N

The drive unit warning is displayed.

Alarm No. Name Meaning 90 Detector: Initial

communication error

Initial communication with the absolute position linear scale failed.

91 Detector: Communication error

An error was detected in the communication with the detector in absolute position detection system.

92 Detector: Protocol error

A data error was detected in absolute position detection system.

93 Initial absolute position fluctuation

The position data have fluctuated during the absolute position initializing.

96 Scale feedback error

An excessive deviation was detected between the motor end detector and MP scale feedback data in a MP scale absolute position detection system.

97 Scale offset error An error was detected in the offset data received from the MP scale in a MP scale absolute position detection system.

9B Detector converting unit: Magnetic pole shift warning

An error was detected in the shift distance of the magnetic pole in a linear servo system.

9C Detector converting unit: Magnetic pole warning

A data error was detected in the magnetic pole of MDS-B-HR after passing Z-phase in a linear servo system.

1. List of Alarms 1.3 Servo spindle Alarms

I - 23

Alarm No. Name Meaning

9E Absolute position detector: Revolution counter error

An error was detected in the revolution counter of the absolute position detector. The absolute position data cannot be compensated.

9F Battery voltage drop

The battery voltage that is supplied to the absolute position detector dropped. The absolute position data is retained.

A6 Fan stop warning A cooling fan built in the drive unit stopped. A8 Turret indexing

warning The designated position shift amount of turret indexing is outside the setting range.

A9 Orientation feedback warning

As an orientation feedback error occurred, the retrial has been conducted.

E0 Over regeneration warning

Over-regeneration detection level exceeded 80%.

E1 Overload warning Overload detection level exceeded 80%. E2 Continuous

high-speed revolution warning

The motor was continuously rotated at a speed exceeding the rated speed.

E3 Absolute position counter warning

Deviation between the absolute and relative position data was detected.

E4 Set parameter warning

A parameter setting was outside the setting range.

E6 Control axis detachment warning

Control axis detachment was commanded.

E7 In NC emergency stop state

Emergency stop was input from the CNC.

E8 Excessive supplementary regeneration frequency

Regeneration that are beyond the power supply limitation has frequently occurred.

E9 Instantaneous power interruption warning

The power was momentarily interrupted.

EA In external emergency stop state

External emergency stop signal was input.

EB Over regeneration warning

Over-regeneration detection level exceeded 80%.

1. List of Alarms 1.4 MCP Alarm

I - 24

1.4 MCP Alarm

An error has occurred in the drive unit and other interfaces. (The bold characters are the messages displayed on the screen.)

Y02 SYSTEM ALARM

An error occurred in the data transmitted between the MCP and drive unit after the power was turned ON.

Error No. Details Remedy

0050 Background error The software or hardware may be damaged. Contact the service center.

0000 CRC error (10 times/910.2 ms)

0001 CRC error (2 continuous times) 0002 Reception timing error

(2 continuous times) 03 Data ID error

(2 continuous times) : Axis No.

0051

04 No. of reception frames error (2 continuous times) : Axis No.

A communication error has occurred between the controller and drive unit. Take measures against noise. Check that the communication cable

connector between the controller and drive unit and one between the drive units are tight.

Check whether the communication cable between the controller and drive unit and one between the drive units are disconnected.

A drive unit may be faulty. Take a note of the 7-segment LED contents of each drive unit and report to the Service Center.

Y03 AMP. UNEQUIPPED The drive unit is not correctly connected

Check the drive unit mounting state. Check the end of the cable wiring. Check the cable for broken wires. Check the connector insertion. The drive unit input power is not being input. The drive unit axis No. switch is illegal.

Error No. Details Alphabet

(axis name) Servo axis drive unit not mounted

1 4 PLC axis drive unit not mounted S No.1 spindle axis drive unit not mounted T No.2 spindle axis drive unit not mounted

Y05 INIT PARAM ERR

: Error parameter number

Details Remedy There is a problem in the value set for the number of axes or the number of systems.

Check the value set for the corresponding parameters. #1001 SYS_ON #1002 axisno #1039 spinno etc.

1. List of Alarms 1.4 MCP Alarm

I - 25

Y06 mcp_no ERROR

There are differences in the MCP and axis parameters when the NC power is turned ON.

Error No. Details Remedy 0001 There is a skipped number in the channels.

0002 The random layout setting is duplicated.

0003 The drive unit fixed setting 0000 and random layout setting are both set.

0004 The spindle/C axis #3031 mcp_no and #3032 smcp_no are set to the same values.

0005 A random layout is set for the #1154 pdoor =1 two-system.

0006 The channel No. parameter is not within the setting range.

Check the values set for the following parameters. #1021 mcp_no #3031 smcp_no #3032 mbmcp_no

Y51 PARAMETER ERROR An error occurred in a parameter that causes an alarm while the control

axis was operating. Error No. Details Remedy

1 LN FEED ABNL (Linear feed abnormal) The time constant has not been set or the setting exceeded the setting range.

Check #2004 G0tL.

2 CT FEED ABNL (Cutting feed abnormal) The time constant has not been set or the setting exceeded the setting range.

Check #2007 G1tL.

3 DLY F-F ABNL (Delayed fast feed abnormal) The time constant has not been set or the setting exceeded the setting range.

Check #2005 G0t1.

4 DLY CUTG ABNL (Delayed cutting feed abnormal)

The time constant has not been set or the setting exceeded the setting range.

Check #2008 G1t1.

9 GRID SPACE ERROR Check #2029 grspc. 12 SYNCHRONOUS TAP CYCLE

ACCELERATION/DECELERATION TIME CONSTANT ERROR

The time constant has not been set or the setting exceeded the setting range.

Check spindle parameters #3017 stapt1 to #3020 stapt4.

15 LN SKIP ABNL (Linear skip abnormal) The time constant has not been set or the setting exceeded the setting range.

Check #2102 skip_tL.

16 DLY SKIP ABNL (Delayed skip abnormal) The time constant has not been set or the setting exceeded the setting range.

Check #2103 skip_t1.

17 "#1205 G0bdcc" for the 2nd system is set to acceleration/deceleration before G0 interpolation.

Check #1205 G0bdcc".

101 ROTARY AXIS GEAR RATIO EXCESSIVE (ABSOLUTE POSITION DETECTION)

Check #2201 PC1 and #2202 PC2.

1. List of Alarms 1.4 MCP Alarm

I - 26

Y90 SP. NON SIGNAL

Alarm No. Details Remedy

0001 0007 There is an error in the spindle encoder signal. The data transmission to the drive unit is stopped when this error occurs.

Check the spindle encoders feedback cable and the encoder.

Alarm No. Z open phase

B open phase

A open phase

1 2 3 4 5 6 7

0 0

(Alarm No.)

No.2 spindle

No.1 spindle

1. List of Alarms 1.5 System Alarms

I - 27

1.5 System Alarms

The following messages are displayed with the register at the time when the error occurred if the system stops due to a system error.

Message Details Remedy Parity error RAM error Write down the displayed register and Bus error A non-existing memory was accessed. contact the service center. Zero divide The division with a 0 denominator was

attempted.

Watch dog error

The software process is not functioning correctly.

Illegal exception

The alarm was caused by an illegal software function not listed above.

Address error An illegal memory was accessed. Illegal instruction

The software process is not functioning correctly.

Stack overflow

Z30 ETHERNET ERROR

Warning No. Warning No. Explanation

0001 Socket open error (socket) 0002 Socket bind error (bind) 0003 Connection wait queue error (listen) 0004 Connection request acceptance error (accept) 0005 Data receive error (socket error) 0006 Data receive error (data shortage or disconnection) 0007 Data receive error (socket error) 0008 Data receive error (data shortage or disconnection) 000A Socket close error (close)

Note: If warning No. 0001, 0002, 0003, or 000A is displayed, set the parameters, then turn power OFF and turn it ON again.

1. List of Alarms 1.5 System Alarms

I - 28

Z31 DATA SERVER ERROR

Warning No. Warning No. Explanation

0001 Socket open error (socket) 0002 Socket bind error (bind) 0003 Connection wait queue error (listen) 0004 Connection request acceptance error (accept) 0005 Data receive error (socket error) 0006 Data receive error (data shortage or disconnection) 0007 Data receive error (socket error) 0008 Data receive error (data shortage or disconnection) 000A Socket close error (close)

Note: If warning No. 0001, 0002, 0003, or 000A is displayed, set the parameters, then turn power OFF and turn it ON again.

Message Details Remedy Z40 FORMAT NOT MET

This appears when the parameter MemVal is formatted at 0, and MemVal is set to 1.

Either return the MemVal setting, or format and restart.

1. List of Alarms 1.5 System Alarms

I - 29

The bold characters are the messages displayed on the screen.

Message Details Remedy

Z51 EE ROM ERROR 000x

This occurs when the parameters were not correctly written into the EEROM. Formatting of the machine manufacturer macro program area did not end correctly. The machine manufacturer macro program was not written into the FROM correctly. Z51 ROM error 0001: Open error Z51 ROM error 0002: Erase error Z51 ROM error 0003: Write error Z51 ROM error 0004: Verify error

If the same alarm is output by the same operation, the cause is an H/W fault. Contact the Service Center.

Reformat the area. Write to the FROM again.

Z52 BATTERY FAULT

The voltage of the battery inserted in the NC control unit has dropped. (The battery used to save the internal data)

Replace the battery of the NC control unit.

After treating the battery check the machining program.

Z53 TEMP. OVER

The controller or operation board temperature has risen above the designated value. (Note 1)

Cooling measures are required. Turn OFF the controller power or lower the temperature with a cooler etc.

Z55 RIO NOT CONNECT

This occurs when an error occurs in the communication between the controller and remote l/O unit. Cable breakage Remote l/O unit fault Power supply to remote l/O unit fault

(Note 2)

Check and replace the cables. Replace the remote I/O unit. Check the power supply. (existence of

supply voltage)

Z57 SYSTEM WARNING

The program memory capacity setting value cannot be formatted. The expansion cassette (HR437) is not mounted after formatting. An expansion cassette different from the expansion cassette (HR437) mounted during formatting is mounted.

(Note 3)

Check the state of the following items. Program memory capacity Status of expansion cassette (HR437)

mounting APLC open option

Z58 ROM WR UNFIN

The machine manufacturer macro program was not written to the FROM after being registered, edited, copied, condensed, merged, the number changed, or deleted.

Write the machine manufacturer macro program to the FROM.

* If the operations, such as editing, done while the NC power was OFF can be invalidated, the program does not need to be written to the FROM.

1. List of Alarms 1.5 System Alarms

I - 30

Message Details Remedy

Z59 TIME CONSTANT

Acceleration and deceleration time constants are too large. (This alarm is output at the same time as T02 FEED HOLD 0206.)

Increase the value specified as the #1206 G1bF parameter.

Decrease the value specified as the #1207 G1btL parameter.

Lower the feedrate.

CAUTION

If the battery low warning is issued, save the machining programs, tool data and parameters in an input/output device, and then replace the battery. When the battery alarm is issued, the machining programs, tool data and parameters may be destroyed. Reload the data after replacing the battery.

Do not replace the battery while the power is ON.

Do not short circuit, charge, heat, incinerate or disassemble the battery.

Dispose of the spent battery following local laws.

Note 1: Temperature warning If the alarm is displayed when an overheat alarm is detected the overheat signal will be output simultaneously. If the machine is in automatic operation the operation will be continued but restarting will not be possible after resetting or stopping with M02/M30. (Starting will be possible after block stop or feed hold.) The alarm will be reset and the overheat signal will turn OFF when the temperature drops below the specified temperature.

Z53 TEMP. OVER 000x

0001 : The temperature in the controller is high.

0002 : The temperature around the communication terminal (setting and display unit) is high.

0003 : The temperature in the controller and around the communication terminal (setting and display unit) is high.

The ambient temperature must be lowered immediately when a Z53 TEMP.OVER alarm occurs but if machining must be continued the alarm can be invalidated by turning the following parameter OFF.

7 6 5 4 3 2 1 0 PLC parameter bit selection #6449

Communication terminal (setting and display unit) 0: Detection invalid Controller 1: Detection valid

1. List of Alarms 1.5 System Alarms

I - 31

Note 2: RIO communication interrupt If communication between the control unit and remote I/O unit fails, the alarm and remote I/O unit number are displayed.

Z55 RIO NOT CONNECT 0 0

(a) and (b) above indicate the following matters.

Alarm number

RIO (seventh station)

RIO (sixth station)

RIO (fifth station)

RIO (fourth station)

Alarm number

RIO (third station)

RIO (second station)

RIO (first station)

RIO (0th station)

0 0

1 1

2 2

3 3

4 4

5 5

6 6

7 7

8 8

9 9

A A

B B

C C

D D

E E

F F

(a)(b)

Board connection remote I/O communication interrupted station Remote I/O 1st system communication interrupted station Remote I/O 2nd system communication interrupted station

This applies for both the remote I/O 1st system communication interrupted station and board connection remote I/O communication interrupted station. Note 3: System warning

Z57 SYSTEM WARNING 00xx 0000 001x : When the expansion cassette (HR437) is not mounted, a program

memory capacity exceeding 1280m was designated. 002x : When the APLC open option was validated, 5120m was

designated for the program memory capacity.

00x1 : After formatting the program memory capacity to 1280m or more, the expansion cassette (HR437) was removed, or an expansion cassette (HR437) not used during formatting was mounted.

1. List of Alarms 1.6 Absolute Position Detection System Alarms

I - 32

1.6 Absolute Position Detection System Alarms

Z70 ABS. ILLEGAL (Error No.) (Axis name)

This error is displayed if the absolute position data is lost in the absolute position detection system.

Error No. Details Remedy Zero point

initialization

Alarm reset when

power is turned OFF

Servo alarm No.

0001 Zero point initialization is incomplete. Otherwise, the spindle was removed.

Complete zero point initialization.

Required

0002 The absolute position reference point data saved in the NC has been destroyed.

Input the parameters. If the reference point data cannot be restored perform zero point initialization.

(Required)

0003 The parameters used to detect the absolute position have been changed. #1003 iunit #2201 PC1 #1016 iout #2202 PC2 #1017 rot #2218 PIT #1018 ccw #2219 RNG1 #1040 M_inch #2220 RNG2 #2049 type #2225 MTYP

Correctly set the parameters. Turn the power on again and perform zero point initialization.

Required

0004 The zero point initialization point is not at the grid position.

Reperform zero point initialization.

Required

0005 Restoration was possible with parameter input in the above No.0002 state.

Turn the power on again and operation will be possible.

Not required

0080 The absolute value data was lost, because the multi-rotation counter data in the detector was incorrect, etc.

Replace the detector and complete zero point initialization.

Required (9E) etc.

0101 The power was turned ON again after the servo alarm No. 25 displayed.

Reperform zero point initialization.

Required (25)

0106 The power was turned ON again after the servo alarm No. E3 displayed.

Reperform zero point initialization.

Required (E3)

Note: To release alarm Z70 ABS. ILLEGAL, enter the parameter data output when establishing the

absolute position and turn ON the power again. For the rotation axis, however, the alarm cannot be released by entering the parameter data.

1. List of Alarms 1.6 Absolute Position Detection System Alarms

I - 33

Z71 DETECTOR ERROR (Error No.) (Axis name)

This alarm is displayed if an error is found in the detector for the absolute position detection system.

Error No. Details Remedy Zero point

initialization

Alarm reset when

power is turned OFF

Servo alarm No.

0001 The backup voltage in the absolute position detector dropped.

Replace the battery check the cable connections and check the detector. Turn the power ON again and perform zero point initialization.

Required (Z70-0101 displays after power is turned ON again.)

25

0003 Communication with the absolute position detector was not possible.

Check and replace the cables card or detector. Turn the power ON again and perform zero point initialization.

(Required) Only when detector is replaced.

Reset 91

0004 The absolute position data fluctuated when establishing the absolute position.

Check and replace the cables card or detector. Turn the power ON again and perform zero point initialization.

(Required) Only when detector is replaced.

Reset 93

0005 An error was found in the serial data from the absolute position detector.

Check and replace the cables card or detector. Turn the power ON again and perform zero point initialization.

(Required) Only when detector is replaced.

Reset 92

0006 Servo alarm E3 Absolute position counter warning

Operation is possible until the power is turned off.

(Required) When power is turned ON again.

Reset (Z70-0106 displays after power is turned ON again.)

E3

0007 Initial communication with the absolute position detector was not possible.

Check and replace the cables card or detector. Turn the power ON again and perform zero point initialization.

(Required) Only when detector is replaced.

Reset 18

1. List of Alarms 1.6 Absolute Position Detection System Alarms

I - 34

Z72 COMPARE ERROR (Alarm No.) (Axis name)

This alarm is displayed if an error is detected when comparing the detectors absolute position and controller coordinate values in the absolute position system.

Alarm No. Details Remedy

Z73 ABS. WARNING (Warning No.) (Axis name)

This displays a warning in the absolute position detection system.

Alarm No. Details Remedy

0001 Servo alarm 9F Battery voltage drop

The battery voltage dropped or a cable is broken. Absolute position initialization is not required.

1. List of Alarms 1.7 Messages During Emergency Stop

I - 35

1.7 Messages During Emergency Stop

EMG EMERGENCY Error items Refer to the explanations for details.

Error No. Details Remedy

PLC The user PLC has entered the emergency stop state during the sequence process.

Investigate and remove the cause of the user PLC emergency stop.

EXIN The emergency stop input signal is significant (open).

Cancel the emergency stop input signal. Check the wiring to see if any wiring is

broken.

SRV An alarm occurred in the servo system causing an emergency stop.

Investigate and remove the cause of the servo alarm.

STOP The user PLC (ladder sequence) is not running.

Check if the rotary switch CS2 on the top of the controller front panel is set to 1.

Check if the PLC edit file save screen (onboard function) [4RUN/SP] (run/stop) switch is turned ON.

SPIN Spindle amplifier not mounted The spindle amplifier is not mounted.

Cancel the causes of the other emergency stop.

Check emergency stop signal input in the spindle amplifier.

PC_H High-speed PC processing abnormal Check the sequence program. (To stop monitoring the high-speed PC processing temporarily, set 1 in #1219 aux03 bit1. Disable the monitoring function only as a temporary measure.)

PARA Setting of the door open II fixed device is illegal. The dog signal random assignment parameter setting is illegal.

Specify the #1155 DOOR_m and #1156 DOOR_s parameters correctly. (When the door open II fixed device is not used, set #1155 DOOR_m and #1156 DOOR_s to 100.)

Correctly set the #2073 zrn_dog, #2074 H/W_OT+, #2075 H/W_OT-and #1226 aux 10 bit 5 parameters.

LINK If the FROM/TO instruction is not executed within 500 ms, an emergency stop occurs.

Try to execute the FROM or TO instruction one or more times every 500 ms.

* Measure the time in which no interrupt request is issued from MELSEC and store the result in the R register.

R1880: Current time-out counter R1881: Counter for maximum time-out

after power-on R1882: Counter for maximum time-out

after system start-up (backed up)

1. List of Alarms 1.7 Messages During Emergency Stop

I - 36

Error No. Details Remedy

LINK MELSEC is held in error and reset states. Check the MELSEC states.

The contents of MELSEC-specific code area in buffer memory have been destroyed.

Check the MELSEC states.

PLC serial link communication has stopped. Note: When WAIT is entered for the PLC

serial link, only the preparation sequence has been established before the communication stops. Therefore, it is supposed that the basic specification parameters related to serial link parameters #1902 and #1903 are incorrect or the #1909 set-time "Tout (ini)" is too short.

Check that HR571 card wiring and external sequencer transmission are normal.

Check the diagnostic screen for link communication errors.

Check whether the basic specification parameters related to serial link parameters are specified correctly.

WAIT The preparation sequence is not sent from the master station. Otherwise, the contents of the received preparation sequence are inconsistent with those of the parameters, so that the usual sequence cannot be started. Note: When LINK is also entered for the

PLC serial link, refer to "Note" in the section, "LINK".

Check that the HR571 card rotary switch and wiring and the external sequencer transmission are normal.

Check the diagnostic screen for link communication errors.

XTEN The HR571 card operates abnormally or the rotary switch is set incorrectly.

Check the HR571 card rotary switch and replace the HR571 card if required.

LAD The user PLC (ladder sequence) has an illegal code.

Check the user PLC (ladder sequence) to see if it uses illegal device numbers or constants.

1. List of Alarms 1.8 Auxiliary Axis Alarms

I - 37

1.8 Auxiliary Axis Alarms

Display example

S01 AUX SERVO ALM

Axis No. 1 to 4

Alarm information (Follows MR-J2-CT alarm information)

(1) S01 AUX SERVO ALM

Alarm information Details Remedy

0011 PCB error 1 An error occurred in the amplifier's internal PCB.

Replace servo amplifier.

0013 Software processing timeout, clock error

An error occurred in the amplifier's internal reference clock.

Replace servo amplifier.

Motor type error Use a correct amplifier and motor combination.

Motor type, detector type error

Detector initial communication error.

Connect correctly. Replace the motor. Replace or repair cable.

0016

Detector CPU error Replace the motor (detector).

0017 PCB error (A/D conversion initial error)

An error occurred in the amplifier's internal A/D converter.

Replace servo amplifier.

Absolute position lost

An error occurred in the detector's internal absolute position data.

0025

Turn the power ON for 2 to 3 minutes while the alarm is occurring, and then turn the power ON again.

Replace the battery, and initialize the absolute position again.

0034 CRC error An error occurred in the communication with the NC.

Take countermeasures against noise.

0036 Communication timeout, NC down

Communication with the NC was cut off.

Connect correctly. Turn the NC power ON. Replace the amplifier or NC.

0037 Parameter error (Regenerative resistance error)

The parameter setting value is incorrect.

Set the parameter correctly.

0038 Frame error An error occurred in the communication with the NC.

Take countermeasures against noise.

0039 INFO error Undefined data was transferred from the NC.

Change the NC software version to a compatible version.

1. List of Alarms 1.8 Auxiliary Axis Alarms

I - 38

(2) S02 AUX SERVO ALM

Alarm information Details Remedy

0011 PCB error 1 (drive circuit error)

An error occurred in the amplifier's internal PCB.

Replace servo amplifier.

0013 Software processing timeout, clock error

An error occurred in the amplifier's internal reference clock.

Replace servo amplifier.

0015 EEROM error A write error occurred to the EEROM in the amplifier.

Replace servo amplifier.

0017 PCB error (A/D conversion error)

An error occurred in the amplifier's internal A/D converter.

Replace servo amplifier.

0018 PCB error (LSI error)

An error occurred in the amplifier's internal LSI.

Replace servo amplifier.

0020 Detector error An error occurred in the communication between the servo amplifier and detector.

Connect correctly. Replace or repair cable.

0024 Ground fault detection

A ground fault of the output was detected when the power was turned ON.

Repair the ground fault section. Replace the cable or motor.

(3) S03 AUX SERVO ALM

Alarm information Details Remedy

0010 Undervoltage The power voltage is 160V or less.

Review the power supply. Replace the servo amplifier.

The tolerable regeneration power of the internal regenerative resistor or external regenerative option was exceeded.

Set the parameter #002 correctly. Connect correctly. Lower the positioning frequency. Change the regenerative option

to a larger capacity. Lower the load. Review the power supply.

0030 Regeneration error

Regenerative transistor error Replace the servo amplifier.

0031 Overspeed The motor's rotation speed exceeded the tolerable momentary speed.

Increase the acceleration/ deceleration time constant.

Review the gear ratio. Replace the detector.

0032 Overcurrent A current exceeding the servo amplifier's tolerable current flowed.

Repair the wiring. Replace the servo amplifier. Take countermeasures against

noise.

1. List of Alarms 1.8 Auxiliary Axis Alarms

I - 39

Alarm information Details Remedy

0033 Overvoltage The voltage of the converter in the servo amplifier was 400V or more.

Wire correctly. Replace the servo amplifier. For the internal regenerative

resistor, replace the amplifier. For the external regenerative

option, replace the regenerative option.

0046 Motor overheating An operation state causing the motor to overheat continued.

Reduce the motor load. Review the operation pattern.

0050 Overload 1 The servo amplifier or servomotor overload protection function activated.

Reduce the motor load. Review the operation pattern. Change to a motor or amplifier

with large output. Change the setting of the

automatic tuning response characteristics.

Correct the connection. Replace the servomotor.

0051 Overload 2 The max. output current flowed for several seconds due to a machine collision or overload.

Review the operation pattern. Change the setting of the

automatic tuning response characteristics.

Correct the connection. Replace the servomotor.

0052 Excessive error A position deflection exceeding the excessive error detection setting value occurred.

Increase the acceleration/ deceleration time constant.

Increase the torque limit value. Review the power facility

capacity. Review the operation pattern. Replace the servomotor. Connect correctly. Repair or replace the cable.

1. List of Alarms 1.8 Auxiliary Axis Alarms

I - 40

(4) S52 AUX SERVO WRN

Alarm information

Details Remedy

0092 Battery voltage drop

The absolute position detection battery voltage dropped.

Mount a battery. Replace the battery and initialize

the absolute position.

00E0 Over-regeneration warning

The regeneration power may have exceeded the tolerable range of the built-in regenerative resistor or external regenerative option.

Lower the positioning frequency. Change the regenerative option

to a larger one. Lower the load.

00E1 Overload warning The overload alarm 1 could occur.

Refer to the items for S03 0050.

00E3 Absolute position counter warning

There is an error in the absolute position detector internal data.

Take countermeasures against noise.

Replace the servomotor.

00E9 Main circuit OFF warning

The servo ON signal was input while the main circuit power was OFF. The contactor operation is faulty.

Turn ON the main circuit power.

(5) Z70 AUX POS. ERR

Alarm information

Details Cause Remedy

0001 Zero point initialization incomplete

The zero point (reference point) has not been initialized in the absolute position system.

Initialize the zero point (reference point).

0002 Absolute position data lost

The absolute position coordinate data in the amplifier has been lost.

Initialize the zero point (reference point).

0003 Absolute position system related parameter error

The absolute position system related parameters have been changed or lost.

Correctly set the parameters and then initialize the zero point (reference point).

(6) Z71 AUX DETEC. ERR

Alarm information

Details Cause Remedy

0001 Absolute position memory battery voltage drop

The data in the detector has been lost. Battery voltage drop. Detector cable wire breakage or looseness.

Check the battery and detector cable and then initialize the zero point (reference point).

1. List of Alarms 1.8 Auxiliary Axis Alarms

I - 41

(7) Z73 AUX SYSTEM WRN

Alarm information

Details Cause Remedy

0001 Absolute position memory battery voltage warning

Battery voltage drop. Detector cable wire breakage or looseness.

Check the battery and detector cable. The zero point does not need to be initialized.

0003 Absolute position counter warning

An error occurred in the detector's absolute position counter.

Replace the detector.

(8) M00 AUX OPER. ALM

Alarm information

Details Cause Remedy

0001 Near-point dog length insufficient

When executing dog-type reference point, the zero point return speed is too fast or the dog length is too short.

Lower the zero point return speed or increase the dog length.

0003 Reference point return direction illegal

When executing reference point return, the axis was moved in the opposite of the designated direction.

Move the axis in the correct direction.

0004 External interlock The axis interlock function is valid.

Cancel the interlock signal

0005 Internal interlock An interlock was established by the servo OFF function.

Cancel the servo OFF.

0007 Soft limit The soft limit was reached. Check the soft limit setting and machine position

0024 In absolute position alarm. Reference point return not possible.

Reference point return was executed during an absolute position alarm.

Initialize the absolute position reference point and then fix the absolute position coordinates.

0025 In initializing absolute position. Reference point return not possible.

Reference point return was executed while initializing the absolute position.

Initialize the absolute position reference point and then fix the absolute position coordinates.

1. List of Alarms 1.8 Auxiliary Axis Alarms

I - 42

(9) M01 AUX OPER. ALM

Alarm information

Details Cause Remedy

0101 No operation mode The operation mode is not designated, or the operation mode was changed during axis movement.

Correctly designate the operation mode.

0103 Feedrate 0 The operation parameter's feedrate setting is zero. The operation parameter feedrate setting is zero. Or, the override is valid, and the override value is zero.

Set a value other than zero in the feedrate setting or override value.

0160 Station No. designation illegal. Starting not possible.

A station No. exceeding the No. of indexed divisions was designated.

Correctly designate the station No.

0161 Reference point return incomplete. Starting not possible.

Automatic/manual operation was started before reference point return was executed with the incremental system.

Execute the reference point return.

0162 In initializing reference point. Starting not possible.

The start signal was input while initializing the absolute position reference point.

Complete the absolute position reference point initialization.

0163 In absolute position alarm. Starting not possible.

The start signal was input during an absolute position alarm.

Initialize the absolute position reference point and then fix the absolute position coordinates.

0164 In random positioning mode. Manual operation not possible.

The manual operation mode was started during the random positioning mode.

Turn the random positioning mode OFF before switching to the manual operation mode.

0165 Uneven indexing station No. illegal. Starting not possible.

The commanded station No. was higher than 9 or the number of indexing stations during uneven indexing.

Check the commanded station No. and the parameter #100 station setting.

1. List of Alarms 1.8 Auxiliary Axis Alarms

I - 43

AUXILIARY AXIS MCP ALARMS

Y02 AUX SYSTEM ALM An error occurred in the data transmitted between the MCP and auxiliary axis amplifier after the power was turned ON.

Error No. Details Remedy

0050 Background error The software or hardware may be damaged. Contact the service center.

0051 0000 CRC error (10 times/910.2ms)

0001 CRC error (2 continuous times)

0002 Reception timing error (2 continuous times)

03 Data ID error (2 continuous times) : Axis No.

04 No. of reception frames error (2 continuous times) : Axis No.

A communication error has occurred between the controller and amplifier. Take measures against noise. Check that the communication cable

connector between the controller and amplifier and one between the amplifiers are tight.

Check whether the communication cable between the controller and amplifier and one between the amplifiers are disconnected.

A driving amplifier may be faulty. Take a note of the 7-segment LED contents of each driving amplifier and report to the Service Center.

Y03 AUX AMP UNEQU. The amplifier is not correctly connected.

Check the auxiliary axis amplifier mounting state. Check the end of the cable wiring. Check the cable for broken wires. Check the connector insertion. The auxiliary axis amplifier input power is not being input. The auxiliary axis amplifier axis No. switch is illegal.

Error No. Details

Axis No.1 to 4 bit correspondence (bit 0 : 1st axis, bit 1: 2nd axis, bit 2: 3rd axis, bit 3: 4th axis)

1. List of Alarms 1.9 Computer Link Errors

I - 44

1.9 Computer Link Errors

Error Message Error No.

Details Remedy

-4 Communication ends with timeout.

CNC has a 248-byte receive buffer.

The time during which CNC receives

248 bytes exceeds the TIME-OUT

value set in the I/O device parameter.

1) Set a greater timeout value in the input/output device parameter.

2) Recheck the HOST software as to whether or not the HOST transmits data in response to DC1 from CNC (data request).

3) Check whether or not start code of computer link parameter is set to 0.

-10 HOST ER (CNC DR) signal is not turned ON.

1) Check whether or not the cable is disconnected from the connector.

2) Check whether or not the cable is broken.

3) Check whether or not the HOST power is turned ON.

-15 Communication ends with parity H. 1) Recheck the HOST software as to whether or not the data to be transmitted to CNC is ISO code.

-16 Communication ends with parity V. 1) Recheck the data to be transmitted to CNC.

L01

DNC ERROR

-17 Although CNC transmits DC3 (request to stop data transfer) to the HOST, it receives data of 10 bytes or more from the HOST, thus terminates communication. When CNC is transmitting data to the HOST, it receives data of 10 bytes or more from the HOST.

1) Recheck the software as to whether or not the HOST stops transmitting data within 10 bytes after receiving DC3.

2) Recheck the HOST software as to whether or not the HOST transmits data such as a command or header to CNC during receiving a work program.

1. List of Alarms 1.10 User PLC Alarms

I - 45

1.10 User PLC Alarms

Sub-status Message

1 2 Details Remedy

U01 No PLC

- - The ladder is not a GPPW ladder or PLC4B ladder. (Note) Emergency stop (EMG) will

be applied.

Download the ladder of the format selected with the PLC environment selection parameters (bit selection #51/bit 4).

0x0010 - Scan time error The scan time is 1 second or longer.

Edit the ladder size to a smaller size.

0x0040 - Ladder operation mode illegal A ladder different from the designated mode was downloaded. (Note) Emergency stop (EMG) will

be applied.

Download the ladder having the same format as when the power was reset or turned ON.

0x0080 - GPPW ladder code error (Note) Emergency stop (EMG) will

be applied.

Download the correct GPPW format ladder.

0x008x - PLC4B ladder code error An illegal circuit was found in the PLC4B ladder. bit1: PC medium-speed circuit

illegal bit2: PC high-speed circuit illegal (Note) Emergency stop (EMG) will

be applied.

Download the correct PLC4B format ladder.

0x0400 Number of ladder steps

Software illegal interrupt The ladder process stopped abnormally due to an illegal software command code. (Note) Emergency stop (EMG) will

be applied.

Turn the power ON again. If the error is not reset, download the correct ladder.

Software exceptional interrupt The ladder process stopped abnormally due to a bus error, etc.

bit 0: BIN command operation error bit 1: BCD command operation error

Refer to the methods for using the BCD and BIN function commands.

U10 Illegal PLC

0x800x Number of ladder steps

bit6: CALL/CALLS/RET command error

bit7: IRET command execution error (Note) Emergency stop (EMG) is

applied for bit 6/7.

Turn the power ON again. If the error is not reset, download the correct ladder.

U50 Stop PLC

The ladder is stopped. Start the ladder.

(Note) The number of ladder steps displayed on the screen may not match the actual number of error occurrence steps because of the ladder timing. Use this as a guideline of the occurrence place.

1. List of Alarms 1.11 Network Service Errors

I - 46

1.11 Network Service Errors

Message Details Remedy

N001 Modem init err

There is an error in the modem connection when the power is turned ON.

Check the connection between the NC and modem, connection port and modem power.

N002 Redial over

The dial transmission failed more than the designated No. of redial times.

Wait a while, and then transmit again.

N003 TEL unconnect

The phone line is not connected. Check the modem's phone line connection.

N004 Net com. error

An error other than the above errors occurred during communication.

Note down the circumstances under which this error occurred, and contact the Service Center.

N005 Bad net com.

The modem connection port is being used for another function such as input/output.

The modem connection port settings are incorrect.

Quit using the modem connection port with the other function, and then turn the power ON again.

Check the modem connection port settings.

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 47

2. Operation Messages on Setting And Display Unit

If a setting operation error occurs on any setting and display unit screen the error No. EOO and a message describing the details of the error will display in the line above the data setting area or the menu display area.

2.1 Operation Errors

: Message requiring resetting and restarting : Message requiring restarting after canceling error conditions

(The bold characters are the messages displayed on the screen.)

Error No. Error message Details

E01 SETTING ERROR The setting data is incorrect. An alphabetic character was set when only number can be set etc.

Data was input without setting number (#). (Word editing)

Even though no retrieval data was set, menu key [ ] or [ ] was pressed.

Even though no data is stored in edit buffers, menu key Replace was pressed.

One of the following characters was entered as the first character of the retrieval data and edit buffers: 0 to 9, ". ", " " (space), "+", "", "=","*", "[ ]", and " " .

When the incremental detection system was used, the parameter (#0 absolute position setting) was set on the absolute position setting screen.

The data input for the standard parameter setting or during execution of formatting is not "Y" or "N".

A value from 4 to 10 was specified for #1043 lang. Or 21 was specified.

Even though no language data exists, its output and comparison were attempted. Check the numbers (0253 and 0254) of the language data to be output.

When the machine manufacturer macro program memory area is the SRAM area, the setup parameter #1060 SETUP was set to 20.

When the machine manufacturer macro program memory area is the SRAM area, writing of the machine manufacturer macro program was attempted on PROGRAM COPY screen.

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 48

Error No. Error message Details

E02 DATA OVER The setting data exceeded the setting range. The compensation data specification exceeded the range when

inputting the tool offset data on tape so that block could not be input. Press the INPUT key again while the input screen is displayed and the input will continue from the next block.

When workpiece coordinate offsets are measured, the calculation results given by pressing the CALC key are exceeding the specified range. Correctly specify the tool length or the wear data of cutting edges used for the calculation.

#1003 iunit was set to D when the least command increment 0.01m option was not available.

When there was no option, 2 or more was specified for #1043 lang. Otherwise, an option was added and 24 or more was specified for #1043 lang.

E03 No. NOT FOUND The corresponding setting No. (#) was not found. This error occurs if a setting No. not found on the screen was set and input or if a variable No. not found in the specifications was set and input for the common variables.

When the tool length was measured manually, a nonexisting tool wear compensation number was specified and the sensor was turned ON. Specify the R register of the offset number correctly.

E04 DEV. NOT READY The input/output unit power is not ON. The cable is disconnected. Setting of the transfer speed (baud rate) does not agree.

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 49

Error No. Error message Details

E05 NOT ACCEPTABLE

The PLC timer cannot be set from the screen when the program is valid. (When machine parameter bit selection #6449 bit 1 is set to 1.)

The PLC counter cannot be set from the screen when the program is valid. (When machine parameter bit selection #6449 bit 0 is set to 1.)

The tool registration data setting is prohibited. (When special relay E71 is valid by the PLC.)

Setting from the tool life management screen is prohibited. Absolute position setting screen's #1 "ORIGIN" and #2 "ZERO"

cannot be set when #0 "INIT SET" is invalid. The total of axes set in #1001 SYS_ON #1002 axisno is illegal.

Set so that the total No. of axes is within the specifications range for the target model.

#1037 cmdtyp is not within the setting range. The INPUT key was pressed to perform search for the program

that is in background edit status on the word edit screen. The menu keys (Replace and Insert) on the word edit screen

were manipulated when a running program is displayed (PDISP signal: ON).

An attempt was made to set MDI data in an MDI setting lock state (the MDI setting lock parameter is specified with 0 and a non-MDI mode is valid).

Language data in display selection status was entered. Change the display selection status once before entering the data. (#1043 lang)

When the manual value command protection (#1228 aux12/bit7) function is valid, the first monitor screen was manipulated by manual command operation (M, S, and T keys).

E06 NO SPEC The menu key for a function not in the specifications was pressed.

A parameter not in the specifications was set. A language that was not added as an option was selected.

(#1043 lang) Set up parameter #1049 mmac_R was set to 1 when the

machine manufacturer macro option was not valid. Set up parameter #1060 SETUP was set to 20 when the

machine manufacturer macro option was not valid. Writing of the machine manufacturer macro program with the

PROGRAM COPY screen was attempted when the machine manufacturer macro option was not valid.

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 50

Error No. Error message Details

E07 RESET END The input/output operations were forcibly stopped by reset etc. (including EMG).

E08 PHYSICAL ERR The input/output parameter setting or input/output unit side setting was incorrect.

E09 TIME OUT The input/output unit parameter "#9116 TIME-OUT SET" setting was too short.

There is no EOB code in the machining program. E10 MEMORY OVER The program cannot be written because the memory capacity is

exceeded. This error occurs when the MDI data setting on the MDI screen

exceeds 500 characters or when saving MDl editing or making a program on the edit screen input on the data input/output screen program copy etc.

E11 PROG. No. DUPLI When registering a machining program in the memory a program with the same No. as the designated program No. was found in the memory. Refer to the program file to find a program No. not being used and reset the program No.

A program with the same No. as the machining program to be copied from the memory was found in the IC card.

This error occurs during MDI registration in the MDI screen or during creation of a program in the edit screen.

E12 FILE ENTRY OVER

When registering a machining program in the memory the No. of programs determined in the specifications is exceeded preventing registration. This error occurs during MDI registration in the MDI screen creation of a program in the edit screen data input in the data input/output screen and program copy.

E13 NB NOT FOUND The block with the designated sequence No. or block No. does not exist in the designated program.

E14 PROG. NOT FOUND

The designated program is not found in the memory. The corresponding program No. was not found with search of

tape memory during graphic check. E15 EDIT LOCK B An operation (edit input/output buffer correction transmit,

delete, etc.) inhibited for machining program B was attempted. E16 EDIT LOCK C An operation (edit input/output buffer correction transmit,

delete, etc.) inhibited for machining program C was attempted.

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 51

Error No. Error message Details

E17 PARITY H ERR A parity H error was detected during data input etc. Check the paper tape or input device. This error may occur if the

paper tape is dirtied with oil etc. E18 PARITY V ERR A parity V error was detected during data input.

Check the paper tape to see whether the number of characters in the significant information section of a block is odd.

Also check the state (cable wiring noise measures etc.) of the connected equipment.

E21 PROGRAM RUNNING

Deletion of a machining program was attempted during operation.

Search was attempted during operation. Change of data such as parameters was attempted during

operation. Start of graphic check was attempted during operation. When using the two systems, the program being buffer corrected

was running with the other system. Erasing or inputting (IC NC) of a program in the IC card being

used was attempted. Formatting of the IC card was attempted during automatic start. Accessing to the host computer was attempted during automatic

operation. E22 CODE CHANGE

ERR There was an illegal code on the paper tape.

E24 PLC RUN Data input/output or comparison was attempted when the PLC was not stopped.

Analog output adjustment was attempted when the PLC was not stopped.

An attempt was made to input or output language data during PLC execution.

When the machine manufacturer macro program memory area was set to the FROM area, formatting of the FROM area (#1060 SETUP 20) was attempted when the PLC was not stopped, writing of the machine manufacturer macro program was attempted on the PROGRAM COPY screen, or input of the macro program was attempted.

(Measures) Stop the PLC. Set the control unit rotary switch to 1. Set the onboard file screen RUN/STOP setting to 1.

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 52

Error No. Error message Details

E25 DATA MEMORY ERR

When inputting the tool offset data onto tape an offset type exceeding the specifications range was designated and that block could not be input. If the INPUT key is pressed again in the input screen the input will continue from the next block.

E26 NO CHARACTERS

The designated character string was not found from the block displayed on the screen to the end of the program when searching with data search in the edit screen. Press the INPUT key again and the search will start at the head of the program.

E35 COMPARE ERROR

An inconsistency was found in the paper tape and memory data during comparison.

E40 OP MODE ERROR Continuous or step graphic check was not possible because the operation mode was illegal.

E50

E51

E52

E53

E54

E55

E56

FILE ERR FILE OPEN ERR FILE CLOSE ERR FILE SEEK ERR FILE READ ERR FILE DELETE ERR FILE INSERT ERR

If one of these errors occurs the editing or input/output operations cannot be continued. Contact the Service Center. As for E50 a classification No. will display at the end of the message. Inform the service center of this No. as well. E55 is also displayed when deleting the system configuration data "ASSEMBLY.INF" of NC memory was attempted on host screen. The system configuration data cannot be deleted.

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 53

Error No. Error message Details

E60

IOP ERR A classification number is displayed after the message for E60. Refer to the section shown in parentheses and remedy the problem.

E60 lOP ERROR - 2 (Port already being used) E60 lOP ERROR - 4 (E09 TIME OUT) E60 lOP ERROR - 5 (E08 PHYSICAL ERR) E60 lOP ERROR - 7 (E07 RESET END) E60 lOP ERROR - 10 (E04 DEV. NOT READY) E60 lOP ERROR - 15 (E17 PARITY H ERR) E60 lOP ERROR - 16 (E18 PARITY V ERR) E60 lOP ERROR - 17 (E20 OVER RUN ERR) E60 lOP ERROR - 18 (E22 CODE CHANGE ERR) E60 IOP ERROR - 20 (framing and H/W errors)

Setting for the bit length is incorrect. (Baud rate, stop bit, and character length) Check the setting of the I/O device system and its parameters and set it again.

Check the situations of the connected devices (cable wiring and noise measures).

Data was input/output or the tape search was executed during the host link. Set 0 in #8109 HOST LINK, and then set 1 again before performing the cycle start. (IOP error -2)

The host link parameter was turned ON during connecting to the Anshin-net. Turn the Anshin-net valid OFF. (IOP error -2)

When #10812 Anshin-net/ Machine builders network system valid is set to 1, the modem connection port of the Anshin-net or machine builders network system is occupied. Perform inputting or outputting using a port other than the modem connection port. (IOP error -2)

When connecting the GX Developer (when the bit selection parameter #6451 bit5 is set to 1), the port 2 of the RS232C communication port is always used. Use a port other than the port 2 of the RS232C communication port. (IOP error -2)

When "#10812 Anshin-net/Machine builders network system valid" is set to 1, the system configuration data output cannot be used. When carrying out the system configuration data output, "#10812 Anshin-net/Machine builders network system valid" is set to 0. (IOP error -2)

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 54

Error No. Error message Details

E62 I/O PARAM ERR The "EIA code" data set for I/O parameter is of an unusable code.

The unusable codes are those used as the EIA standard codes and the even hole codes.

System configuration data output operation was executed without using the data ASCII. Set "0" to EIA output, "1" to data ASCII in the I/O device parameters.

E64 PROGRAM No. ERR

The same No. as the program No. designated for program copy was found in the memory.

During tape input the first character of the machining program block is the program No. address "O" or "L".

E65 PROG. No. DUPLl During tape input the same No. as the specified program was found in the memory.

E66 NO PROG. NUMBER

During tape input the program No. was not found on the paper tape and a program No. was not designated on the screen's data setting area. Set the program No. and input again.

E69 PROG. CHECK MODE

Search (operation search) was attempted during program check (continuous or step).

Retry search after the program check is completed or after resetting the program search

E70 TOOL No. DUPLl A tool No. already registered was newly registered on the tool life management screen.

E71 TOOL ENTRY OVER

Registration of data exceeding the max. No. of registerable tools was attempted on the tool life management screen.

When inputting the tool offset data onto tape a compensation number exceeding the specifications range was specified and that block could not be input. If the INPUT key is pressed again in the input screen, the input will continue from the next block.

E73 CANT CALCULATE

The coordinate value of the hole center cannot be obtained. Reset the measurement point, which must not applied to the

following conditions. The measurement A point is the same as the Y coordinate of the C point. The measurement B is the same as the Y coordinate of the C point. The slope of the line through A and C point is the same as the slope of the line through B and C point.

E74 MENU IMPOSSIBLE

Press the operation menu "= Input" or "+ input" during the tool measurement.

Press the operation menu "= Input" or "+ input" during the manual value command mode.

Press the screen selection menu on which "" is displayed during the tool measurement.

Press the screen selection menu on which "" is displayed during the manual value command mode.

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 55

Error No. Error message Details

E75 TLM ILL. SIGNAL The sensor signal was already ON when the tool measurement mode (TLM) signal was validated.

After the tool measurement mode (TLM) signal was validated, the sensor signal turned ON when there was no axis movement.

The sensor signal turned ON at a position within 100m from the final entry start position.

Turn the tool measurement mode signal input OFF, or turn the sensor signal OFF and move the axis in a safe direction.

(Note) This display will be erased when another screen is opened. The display will not be erased even if the tool

measurement mode signal input is turned OFF, or if the axis is moved in a direction away from the sensor.

E76 TOOL No. ERROR The offset No. to be used for workpiece coordinate system offset data measurement was invalid. Restart from tool selection. (Correctly specify the R register that contains the offset number.)

E77 AXIS No. REF-RET

Zero point return has not been completed for the axis being measured. Return the axis to the zero point.

E78 AX UNMATCH (TLM)

During movement of two or more axes the sensor turned ON and the tool length was measured. Keep off from the sensor and perform the measurement for one axis at a time.

E79 NO REF-RTN (TLM)

The sensor turned on for an axis that has not completed dog-type reference point return and the tool length was measured. Return the axis to the zero point.

E80 TOP SEARCH ERR

The program head search (unmodal type search) was not executed before type 2 (standard specification) restart search was executed for program restart. Set the type to unmodal, search for the head of the program, and then search for the restart block with type 2.

E82 ALREADY RESEARCH

After completing the type 1 or type 2 search for program restart, the unmodal type, type 1 or type 2 search was attempted again.

If program restart is continued (if the axis is return to the restart position with automatic or manual operations), the program will restart from the block searched for first.

To search again, cancel the previous search by resetting, and then search again.

E84 CANT IN/OUT An attempt was made to input a parameter in the setup parameter locked state. Refer to the manual issued by the machine manufacturer.

The parameter "#1925 EtherNet" of the high-speed program server function is set to 0.

When writing data to the IC card, the file name is illegal. (Exceeding 8 characters of file name + 3 characters of extension.)

Input of maintenance data from the host or IC card was attempted.

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 56

Error No. Error message Details

E86 INPUT DATA ERR When inputting the tool offset data the data format was not correct so that block could not be input.

If the INPUT key is pressed again in the input screen the input will continue from the next block.

When data is read from parameter tape, its format is incorrect. The format of file written to the NC memory is illegal.

E87 NOT EDIT PROG. Playback edit was executed for a fixed cycle subprogram. Playback edit of a fixed cycle subprogram is not possible.

E88 CANT ADD BLOCK

Playback edit cannot be executed unless the block being edited with playback is displayed to the end (EOB) on the left side of the

machining program display area. Press the cursor key and display the whole block to the end. Then input the data.

E91 MODE ERROR (PBK)

G90 was set when "PB_G90" was OFF. G91 was set when "PB_G90" was ON.

E98 CANT RESEARCH

When restarting the program, the type 3 restart search was attempted with a program containing no T command. Check the program.

When restarting the program, the T command corresponding to the type 3 restart search was not found in the program. Check the program.

When restarting a program for 2-systems, restart search was performed simultaneously for the 1st and 2nd systems, and then the 2nd system was searched again.

If program restart is continued (if the axis is return to the restart position with automatic or manual operations), the program will restart from the block searched for first.

To search again, cancel the previous search by resetting, and then search again.

When carrying out program restart, restart search 2 was executed during MDI mode. Change to the memory or tape, and search again.

When carrying out program restart, type 3 restart search was attempted while the machine was at the negative (-) side of the restart limit parameters. Manually move the machine to the positive (+) side of the restart limit parameters, and search again.

E165 AUX RUNNING The keys other than Function/Menu/Previous page/Next page were pressed in Auxiliary monitor screen during auxiliary axis operation.

E190 FORE EDITING An attempt was made to perform background search for the program that is in foreground search status. (Word editing)

E191 NOT COM. SEARCH

Operation search was attempted in tape mode.

E200 ADJUST ERROR The hardware status cant be read correctly so automatic adjustment was not possible.

Check the remote l/O unit. A Z55 RIO NOT CONNECT occurred. Adjust manually. Unit defect (replace unit)

2. Operation Messages on Setting And Display Unit 2.1 Operation Errors

I - 57

Error No. Error message Details

E201 UNIT NOT EQUIP The analog output unit is not mounted. Confirm the remote l/O unit. Prepare a unit having analog output. Check the connection (power and signal wires) Unit defect (replace unit)

E301 CONNECT ERROR

A socket connection attempt failed during Ethernet communication.

Check the host address, the setting of the port No. and that the host computer is turned ON.

E302 LOGIN ERR A login attempt failed during Ethernet communication. Check the user name and password.

Check the account settings, such as the home directory. E303 TIME OUT Transmission of a file with Ethernet communication ended

because of timeout. E311 DOWNLOAD ERR An attempt to read a host file failed during Ethernet

communication. E312 UPLOAD ERR An attempt to write to a host file failed during Ethernet

communication. E313 NO FILE The file specified by host receive (host IC) operation during

Ethernet communication is not found in the host. The file specified by host send (IC host) operation during

Ethernet communication is not found in the IC card. E314 FILE DUPLICATE The file name specified to be stored by host receive (host IC)

operation during Ethernet communication already exists in the IC card.

The file name specified to be loaded by host send (IC host) operation during Ethernet communication already exists in the host.

E315 FILE WRITE ERR An attempt to write to the IC card failed during Ethernet communication.

E316 FILE READ ERR An attempt to read a file from the IC card failed during Ethernet communication.

E317 MEMORY OVER IC card memory is full. NC memory is full.

E318 OVER FLOW ERR A host directory contains too many files. E319 DIRECTORY ERR An attempt to move a directory failed.

In the IC card device, accessing a directory in the nineteenth layer or more was attempted.

E320 HR437 UNEQU

When backup or writing of the expansion cassette into/from the FROM, the expansion cassette (HR437) was not mounted in CBUS#1 or was incorrectly mounted.

When backup or writing of the expansion cassette into/from the FROM, a card other than the expansion cassette (HR437) was mounted in CBUS#1.

When the program memory was formatted to 1280m or more, the expansion cassette (HR437) was not mounted in CBUS#1.

2. Operation Messages on Setting And Display Unit 2.2 Operation Messages

I - 58

2.2 Operator Messages

The following messages indicate the status of the setting and display functions and are not operation errors. They are mainly used to show that operation is normal and serve as guides for the following operations. There is no classification by numbers.

2.2.1 Search And Operation Related

Message Message details

SEARCH EXECUTION Search is being executed normally.

SEARCH COMPLET Search was completed normally.

BUFFER EDIT The buffer is being corrected. This appears when the cursor or a tab key is pressed and the buffer correction mode is entered. This is erased when INPUT is pressed.

CANT BUF. EDIT When using 2 systems, the program being buffer corrected is being used by the other system. Buffer correcting of a machine manufacturer macro program was attempted.

DATA PROTECTING Buffer correcting is prohibited since the data protection key 3 is valid.

2. Operation Messages on Setting And Display Unit 2.2 Operation Messages

I - 59

2.2.2 MDI/Editing Related

Message Message details

MDI NO SETTING Only display of MDI data (no execution)

MDI SETTING COMPLETE The MDI data setting has been completed (execution is now possible).

MDI ENTRY COMPLETE The MDI data was saved in the memory with the specified program No.

MDI RUNNING The NC is operating with an MDI program and the MDI data cannot be corrected.

PUSH KEY SERCH/PROG Status in which no programs to be edited have been called on the editing screen. To edit press the SEARCH or PROGRAM edit key.

EDITING The details of a program are being edited on the screen. Press INPUT to write the data in the memory.

PROGRAM RUNNING A machining program to be edited is currently being run with memory operation and cannot be edited.

DELETE? (Y/N) Waiting for a key entry (whether to delete the program) in word edit status (when the background search menu is selected)

BACK GROUND EDITING Background edit mode

EDIT POSSIBLE Editing can be performed in foreground edit mode.

EDIT IMPOSSIBLE Editing cannot be performed in foreground edit mode. This state also occurs during feed hold or fixed cycle mode

(single-block stop).

WORD SEARCH FIN The word matching the search data was searched on word editing.

2. Operation Messages on Setting And Display Unit 2.2 Operation Messages

I - 60

2.2.3 Data Input/Output Related

Message Message details

DATA IN EXECUTION Data is being read without error from the paper tape.

DATA WRITING IN PROGRESS Data has been entered normally and the input data is being written to the ROM.

DATA IN COMPLETE Data has been stored without error.

COMPARE EXECUTION Comparison is being executed without error.

COMPARE COMPLETE Comparison has completed without error.

DATA OUT EXECUTION Data is being output without error.

DATA OUT COMPLETE Data has been output without error.

ERASE EXECUTION Data is being erased without error.

ERASE COMPLETE Data has been erased without error.

COPY EXECUTION The machining program is being copied without error.

COPY COMPLETE The machining program has been copied without error.

CONDENSE EXECUTION The machining program is being condensed without error.

CONDENSE COMPLETE The machining program has been condensed without error.

MERGE EXECUTION The machining program is being merged without error.

MERGE COMPLETE The machining program has been merged without error.

No. CHANGE EXECUTION The machining program No. is being changed without error.

No. CHANGE COMPLETE The machining program No. has been changed without error.

2. Operation Messages on Setting And Display Unit 2.2 Operation Messages

I - 61

2.2.4 S-analog Output Adjustment Related

Message Message details

ADJUST EXECUTION Analog output adjustment is being executed without error.

ADJUST COMPLETE Analog output adjustment has completed without error.

2.2.5 Auxiliary Axis

Message Message details

CONTINUE Y/N Type Y or N to specify whether to perform operation.

BACKUP EXECUTION The auxiliary axis parameters are being backed up in SRAM.

BACKUP COMPLETE The backup of the auxiliary axis parameters in SRAM has been completed.

AUX. WRITING EXEC. The auxiliary axis parameters in SRAM is being written to MR-J2-CT.

WRITE COMPLETE The writing of the auxiliary axis parameters in SRAM to MR-J2-CT has been completed.

ABS POS RESTORED The absolute position in SRAM has been restored in MR-J2-CT.

2.2.6 Parameter Backup Related

Message Message details

BACKUP EXEC. Y/N Type "Y" or "N" to specify whether to perform the operation.

BACKUP EXECUTION The parameters are being backed up.

BACKUP COMPLTE Backup of the parameters has been completed.

RESTORE EXEC. Y/N Type "Y" or "N" to specify whether to perform the operation.

RESTORE EXECUTION The parameters are being restored.

RESTORE COMPLETE Restoration of the parameters has been completed.

2. Operation Messages on Setting And Display Unit 2.2 Operation Messages

I - 62

2.2.7 Others

Message Message details

DATA PROTECTING The data protection key is valid and the various data cannot be set or erased etc.

BASE PARA. SET? (Y/N) Waiting for the key input of standard parameter setting (Y/N).

BASE PARA EXECUTION The standard parameters are being set.

EXECUTE FORMAT? (Y/N) Waiting for the key input of execute format (Y/N).

FORMAT EXECUTION Formatting is being executed.

SETUP COMPLETE The simple setup has been completed. Setup with #1060 SETUP "1" has been completed. Formatting with #1060 SETUP "20" has been completed.

NON SETUP Completed without executing simple setup. (When N has been set for both BASE PARA. SET? (Y/N) and EXECUTE FORMAT? (Y/N).)

CONFIRM OPE? (Y/N) Confirmation for erasing operating time or alarm history.

INPUT? (Y/N) Waiting for the key input of tool length data by manual measurement.

V-ANALIZER EXEC. Waveform display data cannot be output while waveform is displayed.

ROM WRITE? (Y/N) The system is waiting for a key input to indicate whether to write the

macro programs into the FROM.

DATA WRITING The macro program is being written into the FROM.

WRITE COMPLETE The macro program has been written into the FROM.

3. Program Error

I - 63

3. Program Error

(The bold characters are the message displayed in the screen.) These alarms occur during automatic operation and the causes of these alarms are mainly program errors which occur for instance when mistakes have been made in the preparation of the machining programs or when programs which conform to the specification have not been prepared.

Error No. Details Remedy

P 10 EXCS. AXIS No. The number of axis addresses commanded in the same block exceeds the specifications.

Divide the alarm block command into two. Check the specifications.

P 11 AXIS ADR. ERROR The axis address commanded by the program and the axis address set by the parameter do not match.

Revise the axis names in the program.

P 20 DIVISION ERROR An axis command which cannot be divided by the command unit has been issued.

Check the program.

P 29 NOT ACCEPT CMND The normal line control command

(G40.1, G41.1, G42.1) has been issued during the modal in which the normal line control is not acceptable.

2-part system synchronous thread cutting command was issued during a modal for which a 2-part system synchronous thread cutting command cannot be issued.

Check the program.

P 30 PARITY H The number of holes per character on the paper tape is even for EIA code and odd for ISO code.

Check the paper tape. Check the tape puncher and tape reader.

P 31 PARITY V The number of characters per block on the paper tape is odd.

Make the number of characters per block on the paper tape even.

Set the parameter parity V selection OFF. P 32 ADDRESS ERROR

An address not listed in the specifications has been used.

Check and revise the program address. Check and correct the parameters values. Check the specifications.

P 33 FORMAT ERROR The command format in the program is not correct.

Check the program.

3. Program Error

I - 64

Error No. Details Remedy

G-CODE ERROR A G code not listed in the specifications has been used. An illegal G code was commanded during the coordinate rotation command (G68).

Check and correct the G code address in the program.

P 34

G51.2 or G50.2 was commanded when the rotary tool axis No. (#1501 polyax) was set to 0. G51.2 or G50.2 was commanded when the tool axis was set to the linear axis (#1017 rot 0).

Check the parameter setting values.

P 35 CMD-VALUE OVER The setting range for the addresses has been exceeded.

Check the program.

P 36 PROGRAM END ERR EOR has been read during tape and memory operation.

Enter the M02 and M30 command at the end of the program.

Enter the M99 command at the end of the subprogram.

P 37 PROG. NO. ZERO A zero has been specified for program and sequence numbers.

The program numbers are designated across a range from 1 to 99999999.

The sequence numbers are designated across a range from 1 to 99999.

P 39 NO SPEC ERR A non-specified G code was specified. The high-speed program server operation

specifications are not provided.

Check the specifications.

P 40 PREREAD BL. ERR When tool radius compensation is executed there is an error in the pre-read block and so the interference check is disabled.

Reconsider the program.

P 60 OVER CMP. LENG. The commanded movement distance is excessive. (Over 231)

Reconsider the axis address command.

P 62 F-CMD. NOTHING No feed rate command has been issued. There is no F command in the cylindrical

interpolation or pole coordinate interpolation immediately after the G95 mode is commanded.

The default movement modal command at power ON is G01. This causes the machine to move without a G01 command if a movement command is issued in the program, and an alarm results. Use an F command to specify the feedrate.

Specify F with a thread lead command. P 65 NO G05P3 SPEC Check the high-speed mode III

specifications.

3. Program Error

I - 65

Error No. Details Remedy

P 70 ARC ERROR There is an error in the arc start and end

points as well as in the arc center. The difference of the involute curve

through the start point and the end point is large.

When arc was commanded, one of the two axes configuring the arc plane was a scaling valid axis.

Check the numerical values of the addresses that specify the start and end points, arc center as well as the radius in the program.

Check the + and - directions of the address numerical values.

P 71 ARC CENTER The arc center is not sought during

R-specified circular interpolation. The curvature center of the involute curve

cannot be obtained.

Check the numerical values of the addresses in the program.

Check whether the start point or end point is on the inner side of the base circle for involute interpolation. When carrying out tool radius compensation, check that the start point and end point after compensation are not on the inner side of the base circle for involute interpolation.

Check whether the start point and end point are at an even distance from the center of the base circle for involute interpolation.

P 72 NO HELICAL SPEC A helical command has been issued though it is not included in the specifications.

Check the helical specifications. An Axis 3 command was issued by the

circular interpolation command. If there is no helical specification, the linear axis is moved to the next block.

P 90 NO THREAD SPEC A thread cutting command has been issued though it is not included in the specifications.

Check the specifications.

P 93 SCREW PITCH ERR The screw pitch has not been set correctly when the thread cutting command is issued.

Issue the thread cutting command and then set the screw pitch command properly.

P100 NO CYLIND SPEC Cylindrical interpolation was commanded when the cylindrical interpolation specifications were not provided.

Check the specifications.

P111 PLANE CHG (CR) Plane selection commands (G17, G18, and G19) were issued when a coordinate rotation command (G68) was issued.

Before issuing the plane selection commands, issue G68 and then G69 (coordinate rotation cancel).

3. Program Error

I - 66

Error No. Details Remedy

P112 PLANE CHG (CC) A plane selection command (G17 G18

G19) has been issued when the tool radius compensation command (G41 G42) or nose R compensation command (G41 G42 G46) is issued.

The plane selection command was issued when nose R compensation is completed there is no axial movement command after the G40 command and the compensation has not been canceled.

Issue the plane selection command after the tool radius compensation command or nose R compensation command has been canceled (issue axial movement command after the G40 cancel command).

P113 ILLEGAL PLANE The arc command axis is not on the selected plane.

Issue arc command on the correctly selected plane.

P122 NO AUTO C-OVR An automatic corner override command (G62) has been issued though it is not included in the specifications.

Check the specifications. Delete the G62 command from the program.

P126 ILL. CMD(H.A.) An illegal command was issued during the high-accuracy control mode. A G code group 13 command was

issued during the high-accuracy control mode.

Milling, cylindrical interpolation or pole coordinate interpolation was commanded during the high-accuracy control mode.

Reconsider the program.

P130 2nd AUX. ADDR The 2nd miscellaneous function address specified in the program does not match that set by the parameter.

Check and correct the 2nd miscellaneous function address in the program.

P131 NO G96 SPEC (No constant peripheral speed) The constant peripheral speed command (G96) was issued despite the fact that such a command does not exist in the specifications.

Check the specifications. Change from the constant peripheral speed

command (G96) to the rotation speed command (G97).

P132 SPINDLE S = 0 No spindle speed command has been specified.

Reconsider the program.

P133 G96 P-No. ERR An invalid constant peripheral speed control axis has been specified.

Reconsider the parameter specified for the constant peripheral speed control axis.

3. Program Error

I - 67

Error No. Details Remedy

P134 G96 Clamp Err. The constant surface speed control command (G96) was issued without commanding the spindle speed clamp (G92/G50).

Press the reset key and carry out the remedy below.

Check the program. Issue the G92/G50 command before the G96

command. Command the constant surface speed cancel

(G97) to switch to the rotation speed command.

(Applicable only to M65 V series and M64 C version series)

P140 NO T-POS OFST The position compensation command (G45 to G48) specifications are not available.

Check the specifications.

P141 PAT-ROT ERROR Position compensation was commanded during the figure rotation or coordinate rotation command.

Reconsider the program.

P142 T-OFFS G2 ERR A position compensation invalid arc command was commanded.

Reconsider the program.

P150 NO R-CMP SPEC Even though there were no tool radius

compensation specifications, tool radius compensation commands (G41 and G42) were issued.

Even though there were no nose R compensation specifications, nose R compensation commands (G41, G42, and G46) were issued.

Check the specifications.

P151 G2 3 CMP. ERR A compensation command (G40 G41 G42 G43 G44 G46) has been issued in the arc mode (G02 G03).

Issue the linear command (G01) or rapid traverse command (G00) in the compensation command block or cancel block. (Set the modal to linear interpolation.)

P152 I.S.P NOTHING In interference block processing during execution of a tool radius compensation (G41 or G42) or nose R compensation (G41 G42 or G46) command the intersection point after one block is skipped cannot be determined.

Reconsider the program.

P153 I.F ERROR An interference error has arisen while the tool radius compensation command (G41 G42) or nose R compensation command (G41 G42 G46) was being executed.

Reconsider the program.

3. Program Error

I - 68

Error No. Details Remedy

P155 F-CYC ERR (CC) A fixed cycle command has been issued in the radius compensation mode.

The radius compensation mode is established when a fixed cycle command is executed and so the radius compensation cancel command (G40) should be issued.

P156 BOUND DIRECT At the start of G46 nose R compensation the compensation direction is undefined if this shift vector is used.

Change the vector to that with which the compensation direction is defined.

Exchange with a tool having a different tip point number.

P157 SIDE REVERSED During G46 nose R compensation the compensation direction is inverted.

Change the G command to that which allows inversion of the compensation direction (G00 G28 G30 G33 or G53).

Exchange with a tool having a different tip point number.

Turn ON the #8106 G46 inversion error avoidance parameter.

P158 ILLEGAL TIP P. During G46 nose R compensation the tip point is illegal (other than 1 to 8).

Change the tip point number to a legal one.

P170 NO CORR. No. The compensation number (DOO TOO HOO) command was not given when the radius compensation (G41 G42 G43 G46) command was issued. Alternatively the compensation number is larger than the number of sets in the specifications.

Add the compensation number command to the compensation command block.

Check the number of compensation number sets a correct it to a compensation number command within the permitted number of compensation sets.

P172 G10 L-No. ERR (G10 L-number error)

The L address command is not correct when the G10 command is issued.

Check the address L-Number of the G10 command and correct the number.

P173 G10 P-No. ERR (G10 compensation error)

When the G10 command is issued a compensation number outside the permitted number of sets in the specifications has been commanded for the compensation number command.

First check the number of compensation sets and then set the address P designation to within the permitted number of sets.

P177 LIFE COUNT ACT Registration of tool life management data with G10 was attempted when the used data count valid signal was ON.

The tool life management data cannot be registered when counting the used data. Turn the used data count valid signal OFF.

3. Program Error

I - 69

Error No. Details Remedy

P178 LIFE DATA OVER The No. of registration groups total No. of registered tools or the No. of registrations per group exceeded the specifications range.

Review the No. of registrations. The maximum No. of registrations is shown below.

System System 1 System 2

No. of groups 80 40/40

No. of tools 80 40/40

Per group 16

P179 GROUP No. ILL.

When registering the tool life management data with G10 the group No. was commanded in duplicate.

A group No. that was not registered was designated during the T 99 command.

An M code command must be issued as a single command but coexists in the same block as that of another M code command.

The M code commands set in the same group exist in the same block.

The group No. cannot be commanded in duplicate. When registering the group data register it in group units.

Correct to the correct group No.

P180 NO BORING CYC. A fixed cycle command was issued though there are not fixed cycle (G72 G89) specifications.

Check the specifications. Correct the program.

P181 NO S-CMD (TAP) The spindle rotation speed command has not been issued when the hole drilling fixed cycle command is given.

Issue the spindle rotation speed command (S) when the hole drilling fixed cycle command G84 G74 (G84 G88) is given.

P182 SYN TAP ERROR Connection to the main spindle unit was not established.

Check connection to the main spindle. Check that the main spindle encoder exists.

P183 PTC/THD No. The pitch or thread number command has not been issued in the tap cycle of a hole drilling fixed cycle command. The pitch is too small for the spindle rotation speed. The thread number is too large for the spindle rotation speed.

Specify the pitch data and the number of threads by F or E command.

3. Program Error

I - 70

Error No. Details Remedy

P184 NO PTC/THD CMD The pitch or the number of threads per inch is illegal in the tap cycle of the hole drilling fixed cycle command. The pitch is too small for the spindle rotation speed. The thread number is too large for the spindle rotation speed.

Check the pitch or the number of threads per inch.

P190 NO CUTTING CYC A lathe cutting cycle command was input although the lathe cutting cycle was undefined in the specification.

Check the specification. Delete the lathe cutting cycle command.

P191 TAPER LENG ERR In the lathe cutting cycle the specified length of taper section is illegal.

The radius set value in the lathe cycle command must be smaller than the axis shift amount.

P192 CHAMFERING ERR Chamfering in the thread cutting cycle is illegal.

Set a chamfering amount not exceeding the cycle.

P200 NO MRC CYC SPC The fixed cycle for compound lathe I (G70 to G73) was commanded when the fixed cycle for compound lathe I specifications were not provided.

Check the specification.

P201 PROG. ERR (MRC) When called with a fixed cycle for

compound lathe I command, the subprogram contained at least one of the following commands: Reference point return command (G27,

G28, G29, G30) Thread cutting (G33, G34) Fixed cycle skip-function (G31)

The first move block of the finish shape program in fixed cycle for compound lathe I contains an arc command.

Delete the following G codes from this subprogram that is called with the fixed cycle for compound lathe I commands (G70 to G73): G27 G28 G29, G30 G31 G33 G34, fixed cycle G-code.

Remove G2 and G3 from the first move block of the finish shape program in fixed cycle for compound lathe I.

P202 BLOCK OVR (MRC) The number of blocks in the shape program of the fixed cycle for compound lathe I is over 50 or 200 (this differs according to the model).

Specify 50 or a less value. The number of blocks in the shape program called by the fixed cycle for compound lathe I commands (G70 to G73) must be decreased below 50 or 200 (this differs according to the model).

P203 CONF. ERR (MRC) The fixed cycle for compound lathe I (G70 to G73) shape program could not cut the work normally because it defined an abnormal shape.

Check the fixed cycle for compound lathe I (G70 to G73) shape program.

P204 VALUE ERR (MRC) A command value of the fixed cycle for compound lathe (G70 to G76) is illegal.

Check the fixed cycle for compound lathe (G70 to G76) command value.

3. Program Error

I - 71

Error No. Details Remedy

P210 NO PAT CYC SPC A fixed cycle for compound lathe II (G74

to G76) command was input although it was undefined in the specification.

In 1-part system, 2-part system synchronous thread cutting command was issued.

Check the specification.

P220 NO SPECIAL CYC No special fixed cycle specifications are available.

Check the specifications.

P221 NO HOLE (S_CYC) A 0 has been specified for the number of holes in special fixed cycle mode.

Reconsider the program.

P222 G36 ANGLE ERR A G36 command specifies 0 for angle intervals.

Reconsider the program.

P223 G12 G13 R ERR The radius value specified with a G12 or G13 command is below the compensation amount.

Reconsider the program.

P224 NO G12 G13 SPC There are no circular cutting specifications.

Check the specifications.

P230 NESTING OVER A subprogram has been called 4 or more

times in succession from the subprogram. The program in the IC card contains the

M198 command. The program in the IC card has been

called more than once (the program in the IC card can be called only once at a time).

Check the number of subprogram calls and correct the program so that it does not exceed 4 times.

When using the IC card, the IC card and the number of IC card program calls.

P231 NO N-NUMBER At subprogram call time the sequence number set at return from the subprogram or specified by GOTO was not set.

Specify the sequence numbers in the call block of the subprogram.

When using an IC card, check the program and its No. in the IC card.

P232 NO PROGRAM No. The subprogram has not been found when the subprogram is called.

Enter the subprogram. Check the program number in the IC card.

P241 NO VARl NUMBER The variable number commanded is higher than the numbers in the specifications.

Check the specifications. Check the program variable number.

P242 EQL. SYM. MSSG. The "=" sign has not been commanded when a variable is defined.

Designate the "=" sign in the variable definition of the program.

3. Program Error

I - 72

Error No. Details Remedy

P243 VARIABLE ERR. An invalid variable has been specified in the left or right side of an operation expression.

Correct the program.

P252 PAT.&COOD-ROT A coordinate rotation related command (G68, G69) was issued during figure rotation.

Reconsider the program.

P260 NO COOD-RT SPC Even though there were no coordinate rotation specifications, a coordinate rotation command was issued.

Check the specifications.

P270 NO MACRO SPEC A macro specification was commanded though there are no such command specifications.

Check the specifications.

P271 NO MACRO INT. A macro interrupt command has been issued though it is not included in the specifications.

Check the specifications.

P272 MACRO ILL. A statement and a macro statement exist together in the same block.

Reconsider the program and place the executable statement and macro statement in separate blocks.

P273 MACRO OVERCALL The number of macro call nests exceeded the specifications.

Reconsider the program and correct it so that the macro calls do not exceed the limit imposed by the specification.

P275 MACRO ARG. EX. The number of macro call argument type II sets has exceeded the limit.

Reconsider the program.

P276 CALL CANCEL A G67 command was issued though it was not during the G66 command modal.

Reconsider the program. The G67 command is the call cancel

command and so the G66 command must be designated first before it is issued.

P277 MACRO ALM MESG An alarm command has been issued in #3000.

Refer to the operator messages on the DIAG screen.

Refer to the instruction manual issued by the machine manufacturer.

P280 EXC. [ The number of parentheses "[" or "]" which can be commanded in a single block has exceeded five.

Reconsider the program and correct it so the number of "[" or "]" does not exceed five.

P281 [ ] ILLEGAL The number of "[" and "]" parentheses commanded in a single block does not match.

Reconsider the program and correct it so that "[" and "]" parentheses are paired up properly.

P282 CALC. IMPOSS. The arithmetic formula is incorrect.

Reconsider the program and correct the formula.

3. Program Error

I - 73

Error No. Details Remedy

P283 DIVIDE BY ZERO The denominator of the division is zero.

Reconsider the program and correct it so that the denominator for division in the formula is not zero.

P290 IF SNT. ERROR There is an error in the IF conditional GOTO statement.

Reconsider the program.

P291 WHILE SNT. ERR There is an error in the WHILE conditional DO -END statement.

Reconsider the program.

P292 SETVN SNT. ERR There is an error in the SETVN statement when the variable name setting was made.

Reconsider the program. The number of characters in the variable

name of the SETVN statement must be 7 or less.

P293 DO-END EXCESS The number of 's for DO-END in the WHILE conditional DO - END statement has exceed 27.

Reconsider the program and correct it so that the number of 's in the DO - END statement does not exceed 27.

P294 DO-END MMC. The DO's and END's are not paired off properly.

Reconsider the program and correct it so that the DO's and END's are paired off properly.

P295 WHILE/GOTO TPE There is a WHILE or GOTO statement on the tape during tape operation.

During tape operation a program which includes a WHILE or GOTO statement cannot be executed and so the memory operation mode is established instead.

P296 NO ADR (MACRO) A required address has not been specified in the user macro.

Review the program.

P297 ADR-A ERR. The user macro does not use address A as a variable.

Review the program.

P298 PTR OP (MACRO) User macro G200 G201 or G202 was specified during tape or MDI operation.

Review the program.

P300 VER. NAME ERROR The variable names have not been commanded properly.

Reconsider the variable names in the program and correct them.

P301 VAR NAME DUPLI The name of the variable has been duplicated.

Correct the program so that the name is not duplicated.

P350 NO SCALING SPC The scaling command (G50, G51) was issued when the scaling specifications were not available.

Check the specifications.

P360 NO PROG.MIRR. A mirror image (G50.1 or G51.1) command has been issued though the programmable mirror image specifications are not provided.

Check the specifications.

3. Program Error

I - 74

Error No. Details Remedy

P370 NO OPOS MR SPC The facing turret mirror image specifications are not provided.

Check the specifications.

P371 MIRR ILLEGAL Facing turret mirror image was commanded to an axis for which external mirror image or parameter mirror image is valid. Facing turret mirror image validating mirror image for a rotary axis was commanded.

Check the program. Check the parameters.

P380 NO CORNER R/C A command was issued for corner chamfering/corner rounding though there are no such specifications.

Check the specifications. Remove the corner chamfering/corner

rounding command from the program.

P381 NO ARC R/C SPC Corner chamfering/corner rounding was specified in the arc interpolation block although corner chamfering/corner rounding II is unsupported.

Check the specifications.

P382 CORNER NO MOVE The block next to corner chamfering/ corner rounding is not a movement command.

Replace the block succeeding the corner chamfering/corner rounding command by G01 command.

P383 CORNER SHORT In the corner chamfering/corner rounding command the movement distance was shorter than the value in the corner chamfering/corner rounding command.

Make the corner chamfering/corner rounding less than the movement distance since this distance is shorter than the corner chamfering/ corner rounding.

P384 CORNER SHORT When the corner chamfering/corner rounding command was input the movement distance in the following block was shorter than the length of the corner chamfering/corner rounding.

Make the corner chamfering/corner rounding less than the movement distance since this distance in the following block is shorter than the corner chamfering/corner rounding.

P385 G0 G33 IN CONR A block with corner chamfering/corner rounding was given during G00 or G33 modal.

Recheck the program.

P390 NO GEOMETRIC A geometric command was issued though there are no geometric specifications.

Check the specifications.

P391 NO GEOMETRIC 2 There are no geometric IB specifications.

Check the specifications.

P392 LES AGL (GEOMT) The angular difference between the geometric line and line is 1 or less.

Correct the geometric angle.

3. Program Error

I - 75

Error No. Details Remedy

P393 INC ERR (GEOMT) The second geometric block was specified by an incremental value.

Specify this block by an absolute value.

P394 NO G01 (GEOMT) The second geometric block contains no linear command.

Specify the G01 command.

P395 NO ADRS (GEOMT) The geometric format is invalid.

Recheck the program.

P396 PL CHG. (GEOMT) A plane switching command was executed during geometric command processing.

Execute the plane switching command before geometric command processing.

P397 ARC ERR (GEOMT) In geometric IB the circular arc end point does not contact or cross the next block start point.

Recheck the geometric circular arc command and the preceding and following commands.

P398 NO GEOMETRIC 1B Although the geometric IB specifications are not included a geometric command is given.

Check the specifications.

P421 PRAM. IN ERROR The specified parameter number or set

data is illegal. An illegal G command address was

input in parameter input mode. A parameter input command was input

during fixed cycle modal or nose R compensation.

Check the program.

P430 AXIS NOT RET. A command was issued to move an

axis which has not returned to the reference point away from that reference point.

A command was issued to an axis removal axis.

Execute reference point return manually. The command was issued to an axis for

which axis removal is validated so invalidate axis removal.

P431 NO 2nd REF. SPC A command for second third or fourth reference point return was issued though there are no such command specifications.

Check the specifications.

P434 COLLATION ERR One of the axes did not return to the start position when the origin point collate command (G27) was executed.

Check the program.

3. Program Error

I - 76

Error No. Details Remedy

P435 G27/M ERROR An M command was issued simultaneously in the G27 command block.

An M code command cannot be issued in a G27 command block and so the G27 command and M code command must be placed in separate blocks.

P436 G29/M ERROR An M command was issued simultaneously in the G29 command block.

An M code command cannot be issued in a G29 command block and so the G29 command and M code command must be placed in separate blocks.

P438 NOT USE (G52) A local coordinate system command was issued during execution of the G54.1 command.

Review the program.

P450 NO CHUCK BARR. The chuck barrier on command (G22) was specified although the chuck barrier was undefined in the specification.

Check the specification.

P460 TAPE I/O ERROR An error has arisen in the tape reader or alternatively in the printer during macro printing.

Check the power and cable of the connected devices.

Check the I/O device parameters.

P461 FILE I/O ERROR A file of the machining program cannot be read.

In memory mode, the programs stored in memory may have been destroyed. Output all of the programs and tool data once and format them.

Ensure that the external device (including a floppy disk drive and IC card) that contains the file is mounted.

P462 DNC ERROR A communication error occurred during the BTR operation.

L01 DNC ERROR is displayed simultaneously, so remedy the problem according to the error No.

P480 NO MILL SPEC Milling was commanded when the milling

specifications were not provided. Pole coordinate interpolation was

commanded when the pole coordinate interpolation specifications were not provided.

Check the specification.

P481 MILL ILL. G An illegal G code was used during the

milling mode. An illegal G code was used during

cylindrical interpolation or pole coordinate interpolation.

The G07.1 command was issued during the tool radius compensation.

Check the program.

3. Program Error

I - 77

Error No. Details Remedy

P482 MILL ILL. AXIS A rotary axis was commanded during the

milling mode. Milling was executed even though an

illegal value was set for the milling axis No.

Cylindrical interpolation or pole coordinate interpolation was commanded during mirror image.

Cylindrical interpolation or pole coordinate interpolation was commanded before the tool compensation was completed after the T command.

G07.1 was commanded when cylindrical interpolation was not possible (there is no rotary axis, or external mirror image is ON).

G12.1 was commanded when polar coordinate interpolation was not possible.

An axis other than a cylindrical coordinate system axis was commanded during cylindrical interpolation.

Check the machining program, parameters and PLC I/F signal.

P484 MILL AXIS RET. Movement was commanded to an axis

that had not completed reference point return during the milling mode.

Movement was commanded to an axis that had not completed reference point return during cylindrical interpolation or pole coordinate interpolation.

Carry out manual reference point return.

3. Program Error

I - 78

Error No. Details Remedy

P485 MILL ILL. MODAL The milling mode was turned ON during

nose R compensation or constant surface speed control.

A T command was issued during the milling mode.

The mode was switched from milling to cutting during tool compensation.

Cylindrical interpolation or pole coordinate interpolation was commanded during the constant surface speed control mode (G96).

The command unacceptable in the cylindrical interpolation was issued.

A T command was issued during the cylindrical interpolation or pole coordinate interpolation mode.

A movement command was issued when the plane was not selected just before or after the G07.1 command.

A plane selection command was issued during the pole coordinate interpolation mode.

Cylindrical interpolation or pole coordinate interpolation was commanded during tool radius compensation.

The G16 plane in which the radius value of a cylinder is 0 was specified.

A cylindrical interpolation or pole coordinate interpolation command was issued during program coordinate rotation (G68).

Check the program. Before issuing G12.1, issue G40 or G97. Before issuing G12.1, issue a T command. Before issuing G13.1, issue G40. Specify the radius value of a cylinder other

than 0, or specify the X axiss current value other than 0 before issuing G12.1/G16.

P486 MILLING ERROR The milling command was issued during

the mirror image (when parameter or external input is turned ON).

Pole coordinate interpolation, cylindrical interpolation or milling interpolation was commanded during facing turret mirror image.

The start command of the cylindrical interpolation or polar coordinate interpolation was issued during the normal line control.

Check the program.

3. Program Error

I - 79

Error No. Details Remedy

P511 SYNC CODE ERR Two or more synchronization M codes

were commanded in the same block. The synchronization M code and "!" code

were commanded in the same block.

Check the program.

P600 NO AUTO TLM. An automatic tool length measurement command (G37) was execute though there are no such command specifications.

Check the specifications.

P601 NO SKIP SPEC. A skip command (G31) was issued though there are no such command specifications.

Check the specifications.

P602 NO MULTI SKIP A multiple skipping command (G31.1 G31.2 or G31.3) was issued though there are no such command specifications.

Check the specifications.

P603 SKIP SPEED 0 The skip speed is 0.

Specify the skip speed.

P604 TLM ILL. AXIS No axis or more than one axis was specified in the automatic tool length measurement block.

Specify only one axis.

P605 T-CMD IN BLOCK The T code is in the same block as the automatic tool length measurement block.

Specify this T code before the block.

P606 NO T-CMD BEFOR The T code was not yet specified in automatic tool length measurement.

Specify this T code before the block.

P607 TLM ILL. SIGNL Before the area specified by the D command or decelerating area parameter d the measurement position arrival signal went ON. The signal remains OFF to the end.

Check the program.

P608 SKIP ERROR (CC) A skip command was specified during radius compensation processing.

Specify a radius compensation cancel (G40) command or remove the skip command.

3. Program Error

I - 80

Error No. Details Remedy

P610 ILLEGAL PARA. The parameter setting is not correct. G114.1 was commanded when the

spindle synchronization with PLC I/F command was selected.

G113 was commanded when the spindle-spindle polygon machining option was OFF and the spindle synchronization with PLC I/F command was selected.

Check whether #1549 Iv0vR1 to #1553 Iv0vR5 are set in descending order (in order of large values).

Check whether #1554 Iv0rd2 to #1557 Iv0rd5 are set in descending order.

Check and correct #1514 expLinax and #1515 expRotax.

Check the program. Check the parameter.

P612 EXP. ERROR A movement command for exponential function interpolation was issued during facing turret mirror image.

Check the program.

P700 CMD-VALUE ILL. Spindle synchronization was commanded to a spindle that is not connected serially.

Check the program. Check the parameter.

P900 NO TANZ. SPEC A normal line control command (G40.1, G41.1, G42.1) was issued when the normal line control specifications were not provided.

Check the specifications.

P901 TAN. AXIS G92 A coordinate system preset command (G92) was issued to a normal line control axis during normal line control.

Check the program.

P902 TAN. AXIS LINE The normal line control axis was set to a

linear axis. The normal line control axis was set to the

linear type rotary axis II axis. The normal line control axis has not been

set. The normal line control axis was the same

as the plane selection axis.

Correct the normal line control axis.

P903 PLANE CHG (TAN) The plane selection command (G17, G18, G19) was issued during normal line control.

Delete the plane selection command (G17, G18, G19) from the program for normal line control.

P990 PREPRO S/W ERR Combining commands that required pre-reading (nose R offset corner chamfering/corner rounding geometric I geometric IB and fixed cycle for compound lathe) resulted in eight or more pre-read blocks.

Reduce the number of commands that require pre-reading or delete such commands.

II EXPLANATION OF PARAMETERS

1. Screen Configuration 1.1 Screen Transition Charts

II - 1

1. Screen Configuration

1.1 Screen Transition Charts

When the function selection key MENU is pressed the following menu appears: TOOL menu is displayed after the power is turned on. To display PARAM menu use menu key on the TOOL screen.

Machining parameter

#8019 to #8059

CONTROL PARAM

Link parameter

PROCESS I/O BASE PARAM

#9001 to #9014

WORK

WORK PROCESS I/O PAR SETUP MENU

OFFSET REGIST LIFE

Previous page Key Menu selection key

Next page key

MENU

Setup parameter menu display (No.1 to 4)

Tool offset menu display (No.1 to 4)

Previous page

Next page

SETUP PARAMETERPARAM menu

No.1 to 4

MENU

TOOL menu The contents of TOOL menu depends on the system.

. . .

I/O device parameter

BARRIER PARAM

#8300 to #8319

AXIS PARAM #8201 to #8212

Machining parameter

#8001 to #8018

#8071 to #8086

#8101 to #8124

#9101 to #9130

#9501 to #9530

#9601 to #9630

1. Screen Configuration 1.1 Screen Transition Charts

II - 2

Press the menu key SETUP to display the setup selection screen. If the setup parameter menu opening option is specified in this screen, the setup parameters can be set up and displayed.

#3573 to #3584

#3201 to #3212

Spindle parameter

#2261 to #2265

Work Process I/O PAR Setup MENU

MENU

MENU

Offset Registration Life

Previous page key Menu selection key Next page key

MENU

Base Axis Servo Spindle

MC-ERR PLC Macro PSW

Parameter menu display (No.1 to 4)

Tool offset menu display (No.1 to 4)

Setup parameter menu display (No.1 to 4) Setup parameter menu display (No.5 to 8)

Previous page

Next page

Setup parameter menu No.1 to 4

Menu switch

Position switch

#7501 to #7574

PLC timer

#6000 to #6055

Servo parameter

#2201 to #2212

Servo adjustment parameter

Axis specification parameter

#2061 to #2072

Absolute position parameter

#2049 to #2060

#6581 to #6596

Bit selection #6401 to #6460

Machining offset data

#4101 to #4184

Spindle offset parameter

Setup parameter menu No.5 to 8

#5109 to #5124

. . .

. . .

. . .

#1925 to #1936

ASCII macro #7401 to #7415

. . .

#2037 to #2048

Zero point return parameter

#2025 to #2036

Servo specification parameter

Basic specification parameter of spindle

#3001 to #3036

Spindle specification parameter

#6349 to #6396

PLC constant

#6301 to #6348

G macro #7201 to #7313

Macro list M macro

#7001 to #7103

PLC counter #6200 to #6223

#6936 to #6999

. . .

Basic specification parameter

#1001 to #1024

#2013 to #2024

Axis specification parameter

#2001 to #2012

. . .

#4051 to #4097

#2073 to #2084

Machining error correction

#4000 to #4047

#2085 to #2096

Axis specification parameter

Zero point return parameter

Axis specification parameter

Axis specification parameter

Spindle specification parameter

Spindle offset parameter

Machining error correction

Previous page

Next page

2. Machining Parameters 2.1 Process Parameters

II - 3

2. Machining Parameters

2.1 Process Parameters

(No. of workpieces machined) # Item Contents Setup range (unit)

8001 WRK COUNT M Set the M code that counts the No. of workpiece repeated machining. The No. will not be counted when set to 0.

0 to 99

8002 WRK COUNT The current machining No. is displayed. Set the initial value.

0 to 999999

8003 WRK LIMIT Set the maximum No. of workpieces machined. A signal is output to PLC when the No. of machining times is counted to this limit.

0 to 999999

(Automatic tool length measurement)

# Item Contents Setup range (unit) 8004 SPEED Set the feedrate during automatic tool length

measurement. 1 to 60000 (mm/min)

8005 ZONE r Set the distance between the measurement point and deceleration start point.

0 to 99999.999 (mm)

8006 ZONE d Set the tolerable zone of the measurement point. If the sensor signal turns ON in front of d before the measurement point or if the signal does not turn ON after d is passed an alarm will occur.

0 to 99999.999 (mm)

(Automatic corner override)

# Item Contents Setup range (unit) 8007 OVERRIDE Set the override value for automatic corner override. 0 to 100 (%) 8008 MAX ANGLE Set the max. corner opening angle where

deceleration should start automatically. If the angle is larger than this value deceleration will not start.

0 to 180 ()

8009 DSC. ZONE Set the position where deceleration starts at the corner. Designate at which length point before the corner deceleration should start.

0 to 99999.999 (mm)

(Wear data input)

# Item Contents Setup range (unit) 8010 ABS. MAX.

(For L system only) Set the max. value when inputting the tool wear compensation amount. A value exceeding this setting value cannot be set.

0 to 999.999 (mm)

8011 INC. MAX. (For L system only)

Set the max. value for when inputting the tool wear compensation amount in the incremental mode.

0 to 999.999 (mm)

2. Machining Parameters 2.1 Process Parameters

II - 4

(Fixed cycle)

# Item Contents Setup range (unit) 8012 G73 n

(For M system only) Set the return amount for G73 (step cycle). 0 to 99999.999 (mm)

8013 G83 n Set the return amount for G83 (deep hole drilling cycle).

0 to 99999.999 (mm)

8014 CDZ-VALE (For L system only)

Set the screw cut up amount for G76 G78 (thread cutting cycle).

0 to 127 (0.1 lead)

8015 CDZ-ANGLE (For L system only)

Set the screw cut up angle for G76 G78 (thread cutting cycle).

0 to 89 ()

8016 G71 MINIMUM (For L system only)

Set the minimum cut amount for the final cutting in G71 G72 (rough cutting cycle). If the final cutting amount is smaller than this value the final cut will not be performed.

0 to 999.999 (mm)

8017 DELTA-D (For L system only)

Set the change amount to the command cut amount D for G71 G72 (rough cutting cycle). Each cut amount will be the value obtained by adding or subtracting this value from command D and thus the amount can be changed each cut.

0 to 999.999 (mm)

8018 G84/G74 return (For M system only)

Set up return length m at a G84/G74 pecking tap cycle. Note: Set "0" to specify a usual tap cycle.

0 to 999.999 (mm)

2. Machining Parameters 2.1 Process Parameters

II - 5

(High precision control)

# Item Contents Setup range (unit) 8019 R COMP Set up a compensation coefficient for reducing a

control error in the reduction of a corner roundness and arch radius. Indicates a maximum control error (mm) in parentheses. The larger the setup value, the smaller the theoretical error will be. However, since the speed at the corner goes down, the cycle time is extended. Coefficient = 100 - setting value Note: This is valid when "#8021 COMP CHANGE"

is set to "0".

0 to 99 (%)

8020 DCC ANGLE Set up the minimum value of an angle (external angle) that should be assumed to be a corner. When an inter-block angle (external angle) in high-accuracy mode is larger than the set value, it is determined as a corner and the speed goes down to sharpen the edge.

If the set value is smaller than , the speed goes down to optimize the corner.

Note: If "0" is set, it will be handled as 5 degrees.

0 to 89 (degrees) 0: The angle will be

5.

8021 COMP CHANGE Select whether to share or separate the compensation coefficient at the corner/curve during the high-accuracy control mode. 0: Share (#8019 R COMP) 1: Separate Corner (#8022 CORNER COMP) Curve (#8023 CURVE COMP) (Note) Set "1" when using SSS control.

0/1

8022 CORNER COMP Set the compensation coefficient to further reduce or increase the roundness at the corner during the high-accuracy control mode. Coefficient = 100 - setting value Note: This is valid when "#8021 COMP CHANGE"

is set to "1".

-1000 to 99 (%)

8023 CURVE COMP Set the compensation coefficient to further reduce or increase the radius reduction amount at the curve (arc, involute, spline) during the high-accuracy control mode. Coefficient = 100 - setting value Note: This is valid when "#8021 COMP CHANGE"

is set to "1".

-1000 to 99 (%)

8024 EDGE ANGLE Not used. -

2. Machining Parameters 2.1 Process Parameters

II - 6

(High precision control)

# Item Contents Setup range (unit) 8025 SPLINE ON

(for M system only) Specify whether to enable the spline function. 0: Disable the spline function. 1: Enable the spline function.

0/1

8026 CANCEL ANG. (for M system only)

When the angle made by blocks exceeds the set value, spline interpolation is canceled temporarily. In consideration of the pick feed, set a value a little smaller than the pick feed angle.

0 to 180 () 0: 180 ()

8027 Toler-1 (for M system only)

Specify the maximum chord error (tolerance) in a block that includes an inflection point. Set the tolerance applicable when the applicable block is developed to fine segments by CAM. (normally about 10 m) When 0.000 is set, the applicable block is linear.

At 1m 0.000 to 100.000mm At 0.1m 0.0000 to 10.0000mm

8028 Toler-2 (for M system only)

Specify the maximum chord error (tolerance) in a block that includes no inflection point. Set the tolerance applicable when the applicable block is developed to fine segments by CAM. (normally about 10 m) When 0.000 is set, the applicable block is linear.

At 1m 0.000 to 100.000mm At 0.1m 0.0000 to 10.0000mm

8029 FairingL (for M system only)

Set the length of the block subject to fairing. (Valid when #8033 Fairing ON is set to 1.)

0 to 100.000mm

8030 MINUTE LENGTH (for M system only)

When the length of one block exceeds the set value, spline interpolation is canceled temporarily and linear interpolation is performed. Set a value a little smaller than linear block length of the workpiece to be machined. If - 1 is set, spline interpolation is performed regardless of block length.

-1 to 127mm 0: 1mm

8033 Fairing ON (for M system only)

Set whether to use the fairing function. 0: Fairing invalid 1: Fairing valid

0/1

8034 AccClamp ON (for M system only)

Set the method for clamping the cutting speed. 0: Clamp with parameter "#2002 clamp" or the

corner deceleration function. 1: Clamp the cutting speed with acceleration

judgment. (Valid when #8033 Fairing ON is set to 1.)

0/1

8035 AccClampMag Not used. 8036 CordecJudge

(for M system only) Change the conditions for judging a corner. 0: Judge the corner from the angle of the

neighboring block. 1: Judge the corner from the angle of the

neighboring block, excluding minute blocks. (Valid when #8033 Fairing ON is set to 1.)

0/1

8037 CorJudgeL (for M system only)

Set the length of the block to be excluded. (Valid when #8036 CordecJudge is set to 1.)

0 to 99999.999 (mm)

2. Machining Parameters 2.1 Process Parameters

II - 7

# Item Contents Setup range (unit) 8041 C-rot.R This is valid with normal line control type II.

Set the length from the center of the normal line control axis to the end of the tool. This is used to calculate the turning speed at the block joint.

0.000 to 99999.999 (mm)

8042 C-ins.R This is valid with normal line control type I. Set the radius of the arc to be automatically inserted into the corner during normal line control.

0.000 to 99999.999 (mm)

# Item Contents Setup range (unit) 8051 G71 THICK Set the amount of cut-in by the rough cutting cycle

(G71, G72) 0 to 99999.999 (mm)

8052 PULL UP Set the amount of recess after cutting by the rough cutting cycle (G71, G72).

0 to 99999.999 (mm)

8053 G73 U Set the X-axis cutting margin of the forming rough cutting cycle (G73).

-99999.999 to 99999.999 (mm)

8054 W Set the Z-axis cutting margin of the forming rough cutting cycle (G73).

-99999.999 to 99999.999 (mm)

8055 R Set the number of times cutting is performed by the forming rough cutting cycle (G73).

0 to 99999 (times)

8056 G74 RETRACT Set the amount of retract (amount of cut-up) of the push-cut cycle (G74, G75).

0 to 999.999 (mm)

8057 G76 LAST-D Set the amount of final cut-in by the composite threading cycle (G76).

0 to 99.999 (mm)

8058 TIMES Set the number of times the amount of final cut-in (G76 finish margin) is divided in the composite threading cycle (G76).

0 to 99 (times)

8059 ANGLE Set the angle (thread angle) of the tool nose in the composite threading cycle (G76).

0 to 99 ()

<3-dimensional tool radius compensation>

# Item Contents Setup range (unit) 8071 3-D CMP

(for M system only) Value of p in the following denominator constants for 3-dimensional tool radius compensation Vx = i x r/p, Vy = j x r/p, Vz = k x r/p Vx, Vy, Vz: X, Y, and Z axes or vectors of horizontal axes i, j, k: Program command value r: Offset

p = 222 kji ++ when the set value is 0.

0 to 99999.999

2. Machining Parameters 2.1 Process Parameters

II - 8

< Scale factor>

# Item Contents Setup range (unit) 8072 SCALING P

(for M system only) Set the scale factor for reduction or magnification for the machining program for which the G50 or G51 command is issued. This parameter is effective when the program specifies no scale factor.

0 to 99.999999

# Item Contents Setup range (unit) 8073 OfsetPosition

(for M system only) Set the tool offset memory number position for writing the tool information data's tool length offset amount, tool radius compensation amount, tool length wear amount and tool radius wear amount into the tool offset data. Note: If 0 or a value exceeding the number of tool

compensation sets is set, the data will not be written into the tool offset data.

0 to 999

8074 IDMacroTop (for M system only)

Set the head position when writing the tool information data's user areas 4 to 9 in the macro variables.

0 to 999

# Item Contents Setup range (unit) 8075 SpiralEndErr

(for M system only) Designate the tolerable error range (absolute value) when the end point position commanded with the command format type 2 spiral interpolation or conical interpolation command differs from the end point position obtained from the speed and increment/ decrement amount.

0 to 99999.999 (mm)

8076 SpiralMinRad (for M system only)

Not used.

# Item Contents Setup range (unit) 8077 InvoluteErr

(for M system only) Set the tolerable error value of the involute curve that passes through the start point and the involute curve that passes through the end point during involute interpolation.

0 to 99999.999 (mm)

# Item Contents Setup range (unit) 8078 Screen Saver Set the time to turn the screen OFF.

The screen saver will not turn ON if 0 is set. (Note) This parameter setting is valid only for the

LCD display unit.

0 to 60 (min) 0: Do not turn screen

OFF.

2. Machining Parameters 2.1 Process Parameters

II - 9

# Item Contents Setup range (unit) 8083 G83S modeM

(for M system only) Set the M command code for changing to the small diameter deep hole drilling cycle mode.

1 to 99999999

8084 G83S Clearanse (for M system only)

Set the clearance amount for the G83 small diameter deep hole drilling cycle.

0 to 999.999 (mm)

8085 G83S Forward F (for M system only)

Set the feedrate from the R point to the cutting start position in the G83 small diameter deep hole drilling cycle.

0 to 99999 (mm/min)

8086 G83S Back F (for M system only)

Set the speed for returning from the hole base during the G83 small diameter deep hole drilling cycle.

0 to 99999 (mm/min)

# Item Contents Setup range (unit) 8090 SSS ON

(for M system only) Set whether to validate SSS control with G05 P10000.

0: Invalid 1: Valid

0/1

8091 StdLength (for M system only)

Adjust the maximum value of the range for recognizing the shape. To eliminate the effect of steps or errors, etc., set a large value. To enable sufficient deceleration, set a small value. If "0.000" is set, the standard value (1.000mm) will be applied.

0 to 100.000 (mm)

8092 ClampCoeff (for M system only)

Adjust the clamp speed at the curved section configured of fine segments.

Coefficient = setting value

1 to 100

8093 StepLeng (for M system only)

Set the width of the step at which the speed is not to be decelerated. (Approximately the same as the CAM path difference [Tolerance].) If 0 is set, the standard value (5m) will be applied. If a minus value is set, the speed will decelerate at all minute steps.

-0.001 to 0.100 (mm)

8094 DccWaitAdd (for M system only)

Set the time to wait for deceleration when the speed FB does not drop to the clamp speed.

0 to 100 (ms)

8095 Tolerance (for M system only)

Set the tolerable error when the error between the command path and tool path is large. The error will decrease when a small value is set, but the machining time will increase. If "0.000" is set, the error will not be adjusted.

0 to 100.000 (mm)

2. Machining Parameters 2.2 Control Parameters

II - 10

2.2 Control Parameters

# Item Contents Setup range (unit) 8101 MACRO SINGLE Select the control of the blocks where the user

macro command continues. 0: Do not stop while macro block continues. 1: Stop every block during signal block

operation.

0/1

8102 COLL. ALM OFF Select the interference (bite) control to the workpiece from the tool diameter during tool radius compensation and nose R compensation.

0: An alarm is output and operation stops when an interference is judged.

1: Changes the path to avoid interference.

0/1

8103 COLL. CHK OFF Select the interference (bite) control to the workpiece from the tool diameter during tool radius compensation and nose R compensation.

0: Performs interference check. 1: Does not perform interference check.

0/1

8105 EDIT LOCK B Select the edit lock for program Nos. 8000 to 9999. 0: Program can be edited. 1: Editing of above program is prohibited.

0/1

8106 G46 NO REV-ERR (For L system only)

Select the control for the compensation direction reversal in G46 (nose R compensation).

0: An alarm is output and operation stops when the compensation direction is reversed (G41 G42 G42 G41).

1: An alarm does not occur when the compensation direction is reversed and the current compensation direction is maintained.

0/1

8107 R COMPENSATION 0: In arc cutting mode, the machine moves to the inside because of a delay in servo response to a command, making the arc smaller than the command value.

1: In arc cutting mode, the machine compensates the movement to the inside because of a delay in servo response to a command

0/1

8108 R COMP Select Specify whether to perform arc radius error correction over all axes or axis by axis.

0: Perform correction over all axes. 1: Perform correction over axis by axis. Note: This parameter is effective only when

#8107 R COMPENSATION is 1.

0/1

2. Machining Parameters 2.2 Control Parameters

II - 11

# Item Contents Setup range (unit)

8109 HOST LINK Specify whether to enable computer link B instead of the RS-232C port.

0: Disable computer link B to enable normal RS-232C communication.

1: Enable computer link B to disable normal RS-232C communication.

0/1

8110 G71/G72 POCKET Set the pocket machining if there is a dimple (pocket) in the rough cutting cycle (G71, G72) finishing program.

0: Pocket machining OFF 1: Pocket machining ON

0/1

8111 Milling Radius Select the diameter and radius of the linear axis for milling (cylindrical/pole coordinate) interpolation.

0: All axes radius value command 1: Each axis setting (follows #1019 dia diameter

designated axis) Note: This parameter is valid only in the milling

(cylindrical/pole coordinate) interpolation mode.

0/1

8112 DECIMAL PNT-P 0: The decimal point command for G04 address P is invalidated.

1: The decimal point command for G04 address P is validated.

0/1

8113 MillingInitG16 0: Plane other than G16

1: Select G16 plane

8114 MillingInitG19

Designate which plane to use for milling machining after the power is turned ON or reset.

#8113 #8114 Plane 0 0 G17 plane 0 1 G19 plane 1 0 1 1 G16 plane

Note: This parameter is valid for the G code system

2, 3 (#1037 cmdtyp=3, 4).

0: Plane other than G19

1: Select G19 plane

2. Machining Parameters 2.3 Axis Parameters

II - 12

2.3 Axis Parameters

Set up the parameter required for each axis. # Item Contents Setup range (unit)

8201 AX. RELEASE Select the function to remove the control axis from the control target.

0: Control as normal. 1: Remove from control target.

0/1

8202 OT-CHECK OFF Select the stored stroke limit II function set in #8204 and #8205.

0: Stored stroke limit II valid 1: Stored stroke limit II invalid

0/1

8203 OT-CHECK-CANCEL When the simple absolute position method (#2049 type is 9) is selected the stored stroke limits I, II (or IIB) and IB will be invalid until the first zero point return is executed after the power is turned ON.

0: Stored stroke limit II valid (according to #8202)

1: Stored stroke limit II invalid Note: Temporary cancel of #8203 soft limit affects

all the stored stroke limits.

0/1

8204 OT-CHECK-N This sets the coordinates of the (-) direction in the moveable range of the stored stroke limit II or the lower limit coordinates of the prohibited range of stored stroke limit IIB. If the sign and value are the same as #8205, the stored stroke limit II (or IIB) will be invalid. If the stored stroke limit IIB function is selected, the prohibited range will be between two points even when #8204 and #8205 are set in reverse. When II is selected, the entire range will be prohibited.

99999.999 (mm)

8205 OT-CHECK-P This sets the coordinates of the (+) direction in the moveable range of the stored stroke limit II or the upper limit coordinates of the prohibited range of stored stroke limit IIB.

99999.999 (mm)

8206 TOOL CHG. P Set the coordinates of the tool change position for G30. n (tool change position return). Set with coordinates in the basic machine coordinate system.

99999.999 (mm)

8207 G76/87 IGNR (For M system only)

Select the shift operation at G76 (fine boring) and G87 (back boring).

0: Shift effective 1: No shift

8208 G76/87 () (For M system only)

Specifies the shift direction at G76 and G87. 0: Shift to (+) direction 1: Shift to (-) direction

8209 G60 SHIFT (For M system only)

Set the last positioning direction and distance for a G60 (uni-directional positioning) command.

99999.999 (mm)

2. Machining Parameters 2.3 Axis Parameters

II - 13

# Item Contents Setup range (unit)

8210 OT INSIDE The stored stoke limit function to be set in #8204 and #8205 prevents the machine from moving to the inside or outside of the specified range.

0: Inhibits outside area (select stored stroke limit II.)

1: Inhibits inside area (select stored stroke limit II B.)

0/1

8211 MIRR. IMAGE Enable or disable the parameter mirror image function.

0: Disable 1: Enable

0/1

2. Machining Parameters 2.4 Barrier Data

II - 14

2.4 Barrier Data

# Item Contents Setup range (unit) 8300 P0

(For L system only) Set the reference X-coordinates of the chuck and the tail stock barrier. Set the center coordinate (Radius value) of workpiece by the basic machine coordinate system.

99999.999 (mm)

8301 8302 8303 8304 8305 8306

P1 P2 P3 P4 P5 P6 (For L system only)

Set the area of the chuck and tail stock barrier. (Radius value) Set the coordinate value from the center of workpiece for X-axis. Set the coordinate value by basic machine coordinate system for Z-axis.

99999.999 (mm)

8310 Barrier ON (For L system only)

Select the validity of the chuck and tailstock barrier. 0: Invalid (Setting from special display unit valid) 1: Valid

0/1

8311 8312

P7 P8 (For L system only)

Set the area of the left spindle section. X axis: Set the coordinate value from the

workpiece center (P0). (radius value) Z axis: Set the coordinates in the basic

machine coordinate system.

99999.999 (mm)

8313 8314

P9 P10 (For L system only)

Set the area of the right spindle section. X axis: Set the coordinate value from the

workpiece center (P0). (radius value) Z axis: Set the coordinates in the basic

machine coordinate system.

99999.999 (mm)

8315 BARRIER TYPE (L) (For L system only)

Set the shape of the left chuck and tailstock barrier. 0: No area 1: Chuck 2: Tailstock

0/1/2

8316 BARRIER TYPE (R) (For L system only)

Set the shape of the right chuck and tailstock barrier.

0: No area 1: Chuck 2: Tailstock

0/1/2

2. Machining Parameters 2.4 Barrier Data

II - 15

# Item Contents Setup range (unit)

8317 DELIV. AX. NAME (For L system only)

When the right chuck and tailstock barrier is movable, set the name of the delivery axis. When using the 2-system method and the delivery axis is an axis in the other system, designate the system as 1A, 1B or 2A, 2B. If the system is not designated as A and B, the set system will be used.

A/B/.. (axis address)

1A/1B/.. 2A/2B/..

(system designation) 0 (cancel)

8318 STOCK ANGLE (L) (For L system only)

Set the angle for the left tailstock end section. The angle will be interpreted as 90 if there is no setting (0).

0 to 180 () 0: 90 default

8319 STOCK ANGLE (R) (For L system only)

Set the angle for the right tailstock end section. The angle will be interpreted as 90 if there is no setting (0).

0 to 180 ()

2. Machining Parameters 2.5 Tool Measurement Parameters

II - 16

2.5 Tool Measurement Parameters

Set up the parameter of the tool (touch tool sensor), etc, used for measurement. # Item Contents Setup range (unit)

8701 Tool length Set the length to the end of the touch tool. 99999.999 (mm) 8702 Tool Dia Set the spherical diameter of the touch tool end. 99999.999 (mm) 8703 OFFSET X Set the spindle center deviation amount from the

touch tool center in the X axis direction. 99999.999 (mm)

8704 Y Set the spindle center deviation amount from the touch tool center in the Y axis direction.

99999.999 (mm)

8705 RETURN Set the return distance to contact the touch tool against the workpiece again.

99999.999 (mm)

8706 FEED Set the feedrate when contacting the touch tool against the workpiece again.

1 to 60000 (mm/min)

3. I/O Parameters 3.1 Base Parameters

II - 17

3. I/O Parameters

Pressing the menu key I/O PARA displays the I/O BASE PARAM screen.

There are basically two types of input/output parameters which must be set when inputting outputting or referring to data or when performing tape operation. One type is the parameters related to the input/output device. The baud rate etc. is set according to each device. Up to five types of input/output devices can be registered. The other type of input/output parameters is the I/O base parameters which determine which device is connected to which channel per input/output application.

3.1 Base Parameters

# # Specify the board No. to which the serial

input/output device is connected to 2. Set "1" to use ch1. Set "2" to use ch2.

Set the input/output device No. for each application. The device Nos. are 0 to 4 and correspond to the input/output device parameters. The device name set in the input/output device parameter is also displayed for identification.

DATA IN 9001 Specify the port for inputting the data such as machine program and parameters.

9002 Specify the device No. that inputs the data.

DATA OUT 9003 Specify the port for outputting the data such as machine program and parameters.

9004 Specify the device No. that outputs the data.

TAPE MODE 9005 Specify the input port for running with the tape mode.

9006 Specify the device No. to be run with the tape mode.

MACRO PRINT

9007 Specify the output port for the user macro DPRINT command.

9008 Specify the device No. for the DPRINT command.

PLC IN/OUT 9009 Specify the port for inputting/outputting various data with PLC.

9010 Specify the device No. for the PLC input/output.

REMOTE PROG IN

9011 Specify the port for inputting remote programs. The port No. must be "2".

9012 Specify the device No. used to input remote programs.

EXT UNIT 9013 Specify the port for communication with an external unit.

9014 Specify the unit No. used for communication with an external unit

# Item Contents Setup range (unit)

9015 PORT NO. (tool ID)

Set the number of the port connected with the tool ID. (Either ch1 or ch2 can be used.) Set "1" to use ch1. Set "2" to use ch2.

1/2 (M64)

9016 DEV. NO. (tool ID)

Set the number of the input/output device to be used. (Any device No. can be used.)

0 to 4 (M64)

3. I/O Parameters 3.2 I/O Device Parameters

II - 18

3.2 I/O Device Parameters

Parameters for up to five types of input/output devices can be set in DEV <0> to <4>. # Item Contents Setup range (unit)

9101 DEVICE NAME Set the device name corresponding to the device No. Set a simple name for quick identification.

Use alphabet characters numerals and symbols to set a name within 3 characters.

9102 BAUD RATE Set the serial communication speed. 0: 19200 (bps) 1: 9600 2: 4800 3: 2400 4: 1200 5: 600 6: 300 7: 150

9103 STOP BIT Set the stop bit length used in the start-stop system. 1: 1 (bit) 2: 1.5 3: 2

9104 PARITY CHECK Specify whether to add the parity check bit to the data during communication.

0: Parity bit not added 1: Parity bit added

9105 EVEN PARITY Specify the odd or even parity when it is added to the data.

0: Odd parity 1: Even parity

9106 CHR. LENGTH Set the length of the data bit. 0: 5 (bit) 1: 6 2: 7 3: 8

9107 TERMINATOR TYPE The code to terminate data reading can be selected. 0 and 3: EOR 1 and 2: EOB or EOR

9108 HAND SHAKE Specify the transmission control method. The method will be no procedure if a value except 1 to 3 is set.

1: RTS/CTS method 2: No procedure (No

handshaking) 3: DC code method

9109 DC CODE PARITY Specify the DC code when the DC code method is selected.

0: No parity to DC code (DC3 = 13H)

1: DC code with parity (DC3 = 93H)

9111 DC2/DC4 OUTPUT Specify the DC code handling when outputting data to the output device.

DC2 / DC4 0: None / None 1: Yes / None 2: None / Yes 3: Yes / Yes

9112 CR OUTPUT Specify whether to insert the code just before the EOB (L/F) code during output.

0: Do not add 1: Add

3. I/O Parameters 3.2 I/O Device Parameters

II - 19

# Item Contents Setup range (unit)

9113 EIA OUTPUT In data output mode, select the ISO or EIA code for data output. In data input mode, the ISO and EIA codes are identified automatically.

0: ISO code output 1: EIA code output

9114 FEED CHR. Specify the length of the tape feed to be output at the start and end of the data during tape output.

0 to 999 (characters)

9115 PARITY V Specify whether to check the parity of the No. of characters in block during data input. The No. of characters is factory-set so that the check is valid at all times.

0: Do not perform parity V check

1: Perform parity V check

9116 TIME-OUT Set the time out time to detect an interruption in communication. Time out check will not be executed when set to 0 to 30 seconds.

0 to 30 (s)

9117 DR OFF Specify whether to check the DR data at the data input/output.

0: DR valid 1: DR invalid

9118 DATA ASC II 0: Output in ISO/EIA code (Depends on whether #9113, #9213, #9313, #9413, or #9513 EIA output parameter is set up)

1: Output in ASC II code

0/1

9119 INPUT FORM Specify the mode for input (collation). 0: Standard input (Data from the very first EOB is

handled as significant information.) 1: EOBs following the first EOB of the input data are

skipped until data other than EOB is input.

0/1

9121 9122 9123 9124 9125 9126 9127 9128

EIA CODE [ ] # = : $ !

When output with EIA code data can be output using the alternate code in which the special ISO code not included in EIA is specified. Specify the codes which do not duplicate the existing EIA codes by hexadecimal for respective special codes.

0 to FF (hexadecimal)

9201 Set the same settings for device 1. 9301 Set the same settings for device 2. 9401 Set the same settings for device 3. 9501 Set the same settings for device 4.

3. I/O Parameters 3.3 Computer Link Parameters

II - 20

3.3 Computer Link Parameters

# Item Contents Setup range (unit) 9601 BAUD RATE Specify the rate at which data is transferred. 0: 19200 (bps)

1: 9600 2: 4800 3: 2400 4: 1200 5: 600 6: 300 7: 110 8: 38400

9602 STOP BIT Specify stop bit length used in start-stop mode. See "PARITY EFFECTIVE" in #9603. The number of characters is adjusted in output mode so that no problems occur if the parity check is enabled.

1: 1 2: 1.5 3: 2

9603 PARITY EFFECTIVE This parameter is set when using a parity bit separately from the data bit.

ON OFF

Start bit Data bit

b1 b2 b3 b4 b5 b6 bn

1 character

Stop bitParity bit Set this to match the input/output device specifications.

0: No parity bit used in I/O mode

1: Parity bit used in I/O mode

9604 EVEN PARITY Specify whether even or odd parity is used when parity is used. This parameter is ignored when no parity is used.

0: Odd parity 1: Even parity

9605 CHR. LENGTH Specify data bit length. See "PARITY EFFECTIVE" in #9603.

2: 7 3: 8

9606 HAND SHAKE RS-232C transmission control mode DC control mode should be set for computer line B.

0: No control 1: RTS/CTS method 2: No handshaking 3: DC control mode

9607 TIME-OUT SET Specify time-out time at which an interruption of data transfer during data input/output should be detected. If 0 is set, time infinity is specified.

0 to 999 (1/10s)

9608 DATA CODE Specify the code to be used. See PARITY EFFECTIVE in #9603.

0: ASCII code 1: ISO code

3. I/O Parameters 3.3 Computer Link Parameters

II - 21

# Item Contents Setup range (unit)

9609 LINK PARAM. 1 Bit 1: DC1 output after NAK or SYN Specify whether to output the DC1 code after the

NAK or SYN code is output. Bit 7: Enable/disable resetting Specify whether to enable resetting in the

computer link.

0: Don't output the DC1 code.

1: Output the DC1 code.

0: Enable resetting in

the computer link. 1: Disable resetting in

the computer link 9610 LINK PARAM. 2 Bit 2: Specify the control code parity (even parity for

the control code). Set the parity in accordance with the I/O device

specifications. Bit 3: Parity V Specify whether to enable checking of parity V in

one block in data input mode.

0: No control code parity added

1: Control code parity added

0: Disable 1: Enable

9611 LINK PARAM. 3 Not used 9612 LINK PARAM.4 Not used 9613 LINK PARAM.5 Not used 9614 START CODE Specify the code by which file data transfer begins

at first. This parameter is used for a specific user, and set 0 in this parameter for normal operation.

0: DC1 (11H) 1: BEL (07H)

9615 CTRL. CODE OUT Bit 0: NAK output Specify whether to send the NAK code to the host if a communication error occurs in computer link B.

Bit 1: SYN output Specify whether to send the SYN code to the host if NC resetting or an emergency stop occurs in computer link B.

Bit 3: DC3 output Specify whether to send the DC3 code to the host when communication ends in computer link B.

0: Do not output the NAK code.

1: Output the NAK code.

0: Do not output the

SYN code. 1: Output the SYN

code. 0: Do not output the

DC3 code. 1: Output the DC3

code. 9616 CTRL. INTERVAL Not used 9617 WAIT TIME Not used 9618 PACKET LENGTH Not used 9619 BUFFER SIZE Not used 9620 START SIZE Not used 9621 DC1 OUT SIZE Not used 9622 POLLING TIMER Not used 9623 TRANS. WAIT TMR Not used 9624 RETRY COUNTER Not used

4. Setup Parameters

II - 22

4. Setup Parameters

Pressing the menu key SETUP displays the OPEN SETUP PARAM screen. The system's basic parameters are normally hidden as setup parameters to prevent mistaken operations and to simplify the display. The setup parameters can be displayed and set by making a declaration to open the setup parameters on this screen.

1) Select the setup parameter. Key-in "Y" in # ( ) and then press INPUT.

The basic specification parameter screen appears and the normally hidden setup parameter menu will display.

The required menu can be selected to display and set the setup parameters.

2) Cancel the setup parameter selection. Key-in "N" in # ( ) and then press INPUT. The setup parameter menu will disappear. Note: The setup parameters are not displayed when the power is turned ON.

(Note 1) Refer to "5. Base Specifications Parameters" to "13. Position Switch" for details on the setup

parameters. (Note 2) Be sure to turn OFF the power supply after selecting the setup parameter. (Note 3) If a key other than the screen changeover key is pressed when the setup parameters are locked,

the message "Data Protected" will appear.

MENU I/O PARPROCESSWORK

PARAM 3 [OPEN SETUP PARAM]

Open the menu setup parameter? *YES: Y INPUT *NO: N INPUT

SETUP

# ( )

5. Base Specifications Parameters

II - 23

5. Base Specifications Parameters

After setting up the parameter (PR) listed in the table, turn OFF the NC power. To validate the parameter, turn ON the power again.

(SETUP PARAM 1. 1/15) # Items Details Setting range (unit)

1001 (PR)

SYS_ON System validation setup

Specify the existence of the 1st system 2nd system and PLC axis with 1 or 0.

0: Not used 1: Used

1002 (PR)

axisno Number of axes

Set No. of axes in each system and the No. of PLC axes. Specify 6 as the maximum value for each system and 4 as that for the PLC axis so that the total of those values is 6 or less.

0 to 6

1003 (PR)

iunit Input setup unit

Specify the input setting value for each system and the PLC axis. The parameter units will follow this specification.

B: 1 m C: 0.1 m D: 0.01 m

1013 axname Axis name Specify each axis name address with an alphabetic character. Use the characters X Y Z U V W A B or C. Do not specify the same address in one system. The same address can be specified for the 1st and 2nd system. The PLC address does not need to be set. (The axis name is displayed as 1 and 2.)

Axis addresses such as X, Y, Z, U, V, W, A, B, and C

1014 incax Increment command axis name

When specifying the program movement rates absolute or incremental method with an address specify the incremental command axis name address with an alphabetic character. The address that can be used is the same as #1013 axname. Specify an address that is different from that #1013. Setting is not required if absolute/incremental specification with addresses is not performed (#1076 Abslnc = 0).

1015 (PR)

cunit Command unit

Specify the minimum unit of the program movement amount.

cunit Movement amount for movement command 1

0: Follow #1003 iunit 1: 0.0001 mm ( 0.1 m) 10: 0.001 mm ( 1 m) 100: 0.01 mm ( 10 m) 1000: 0.1 mm (100 m) 10000: 1.0 mm If there is a decimal point in the movement command the decimal point position will be handled as 1mm regardless of this setting.

0 #1003 iunit

1 0.1 m

10 1 m

100 10 m

1000 100 m

10000 1 mm

5. Base Specifications Parameters

II - 24

# Items Details Setting range (unit)

1016 (PR)

iout Inch output Specify whether the machine system (ball screw pitch position detection unit) is an inch unit system or metric unit system.

0: Metric unit system 1: Inch unit system

1017 (PR)

rot Rotational axis

Specify whether the axis is a rotary axis or linear axis. For the rotary axis the position display will be 360 and the axis will return to 0. If the position display is to be continuously displayed even with the rotary axis set the axis as a linear axis

0: Linear axis 1: Rotary axis

1018 (PR)

ccw Motor CCW Specify the direction of the motor rotation to the command direction.

0: Rotates clockwise (looking from motor shaft) with the forward rotation command.

1: Rotates counterclockwise (looking from motor shaft) with the forward rotation command.

0: Rotates clockwise 1: Rotates counter-

clockwise

1019 (PR)

dia Diameter specification axis

Specify whether the program movement amount is to be commanded with the diameter dimension or as movement amount. When the movement amount is commanded with the diameter dimensions 5mm will be moved when the command is a movement distance of 10mm. The movement amount per pulse will also be halved during manual pulse feed. Among parameters concerning length the tool length the wear compensation amount and the workpiece coordinate offset are displayed in diameter value when diameter is specified but other parameters are always displayed in radius value.

0: Command with movement amount

1: Command with diameter dimension

1020 (PR)

sp_ax Spindle Interpolation

Specify 1 when the NC control axis is used as the spindle.

0: The NC control axis is used as the servo axis.

1: The NC control axis is used as the spindle.

1021 (PR)

mcp_no Amplifier I/F channel No. (servo)

Using a 4-digit number, set the amplifier interface channel No. and which axis in that channel is to be used when connecting an axis amplifier. High-order two digits : Amplifier interface channel No. Low-order two digits : Axis No. When using the conventional fixed layout, set all axes to 0000.

0000 0101 to 0107 0201 to 0207

1022 (PR)

axname2 2nd axis name

Set the name of the axis displayed on the screen with two characters. (X1, Z2, etc.)

Two digits between A to Z and 1 to 9 (Setting is cleared when 0 is set)

5. Base Specifications Parameters

II - 25

# Items Details Setting range (unit)

1023 (PR)

crsadr Command address during cross machining

Set the address for issuing a command to this axis during cross machining control.

A to Z (Setting is cleared when 0 is set)

1024 (PR)

crsinc Incremental command address during cross machining

Set the address for issuing an incremental command to this axis during cross machining control.

A to Z (Setting is cleared when 0 is set)

(SETUP PARAM 1. 2/15) # Items Details Setting range (unit)

1025 l_plane Initial plane selection

Specify the plane to be selected when the power is turned ON or reset. When 0 is specified, 1 is assumed (X-Y plane).

1: X-Y plane (G17 command state)

2: Z-X plane (G18 command state)

3: Y-Z plane (G19 command state)

1026 1027 1028

base_l base_J base_K

Base axis I Base axis J Base axis K

Specify the basic axis address that composes the plane. Specify the axis address set in #1013 axname. If all three items do not need to be specified such as for 2-axis specifications input 0 and the parameter will be blank. Normally when X Y and Z are specified respectively for base_l_J_K the following relation will be established:

G17: X-Y G18: Z-X G19: Y-Z

Specify the desired address to set an axis address other than the above.

Control axis addresses such as X, Y, and Z

1029 aux_I Flat axis I If there is an axis parallel to #1026 base_l specify that axis address.

Control axis addresses such as X, Y, and Z

1030 aux_J Flat axis J If there is an axis parallel to #1027 base_J specify that axis address.

Control axis addresses such as X, Y, and Z

1031 aux_K Flat axis K If there is an axis parallel to #1028 base_K specify that axis address.

Control axis addresses such as X, Y, and Z

5. Base Specifications Parameters

II - 26

# Items Details Setting range (unit)

1037 cmdtyp Command type

Specify the program G code series and compensation type. There are some items in the specifications that can be used or cannot be used according to the value set in this parameter. The file structure may also change depending on the compensation data type. Thus after changing this parameter initialize the system with #1060 SETUP.

1 to 8

1038 plcsel Ladder selection

Specify the PLC type. 0: User custom PLC 1: Standard PLC 2: Exclusive PLC for

MELSEC bus link 1039 spinno Number of

spindles Specify the existence of a spindle. 0: No spindle

1: One spindle 2: Two spindles 3: Three spindles 4: Four spindles

1040 (PR)

M_inch Constant input (inch)

Specify the parameter unit system for the position and length.

0: Metric system 1: Inch system

1041 (PR)

l_inch Initial state (inch)

Specify the unit system for the program movement amount when the power is turned ON or reset and for position display. Designate an internal unit.

0: Metric system 1: Inch system

1042 (PR)

pcinch PLC axis command (inch)

Specify the unit system for the commands to the PLC axis.

0: Metric system 1: Inch system

cmdtyp G code series Compensation type 1 System 1 (for M) Type A (one compensation

amount for one compen- sation number)

2 System 2 (for M) Type B (shape and wear amounts for one compen- sation number)

3 System 2 (for L) Type C (two kinds of compensation amount of shape and wear per compensation No.)

4 System 3 (for L) Same as above 5 System 4

(for special L) Same as above

6 System 5 (for special L)

Same as above

7 System 6 (for special L)

Same as above

8 System 7 (for special L)

Same as above

5. Base Specifications Parameters

II - 27

# Items Details Setting range (unit)

1043 lang Select language displayed

Specify the display language.

0: Japanese display (Standard) 1: English display (Standard) 2: Third language displayed (Note) (Option) 3: Fourth language displayed (Note) (Option) 11: Display in German (Option) 12: Display in French (Option) 13: Display in Italian (Option) 14: Display in Spanish (Option) 15: Display in Chinese (Option)

(traditional Chinese) 16: Display in Korean (Option) 17: Display in Portuguese (Option) 18: Display in Dutch (Option) 19: Display in Swedish (Option) 20: Display in Hungarian (Option) 22: Display in Chinese (Option) (simplified Chinese) 23: Display in Russian (Option)

Note: If no character package is available for a

specified language, the screen is displayed in English.

0 to 3 11 to 22

1044 (PR)

auxno MR-J2-CT Connections

Specify the number of MR-J2-CTs connected. 0 to 4

1045 (PR)

nskno Megatorgue motor connections

Specify the number of NSK megatorque motors connected. When a value other than 0 is specified, 2nd miscellaneous function data is output as signed binary data.

0 to 16

1049 (PR)

mmac_R Machine maker macro RAM-ROM changeover

Select the memory area for the machine manufacturer macro program. 0: SRAM area 1: FROM area When this parameter is changed, the power must be turned OFF and ON, and the area must be formatted. Note: 1 cannot be set if the machine

manufacturer macro option is not valid.

0/1

Note: Selection of inch and metric unit

When set value of #1041 I_inch is changed the unit of length is changed after reset. Among parameters concerning length following items are not changed automatically therefore change the set values to agree with the new unit system when the unit system is changed.

5. Base Specifications Parameters

II - 28

Tool compensation amount (Tool length compensation amount tool wear compensation amount and tool tip compensation amount) Workpiece coordinate offset

#8004 SPEED #8027 Toler-1 #8056 G74 RETRACT #8005 ZONE r #8028 Toler-2 #8057 G76 LAST-D #8006 ZONE d #8029 FairingL #8075 SpiralEndErr #8009 DSC. ZONE #8030 MINUTE LENGS #8010 ABS. MAX. #8037 CorJudgeL

#8077 InvoluteErr

#8011 INC. MAX. #8041 C-rot. R #8012 G73n #8042 C-ins. R

#8084 G83S Clearanse

#8013 G83n #8051 G71 THICK #8085 G83S Forward F #8016 G71 MINIMUM #8052 PULL UP #8086 G83S Back F #8017 G71 DELTA-D #8053 G73U

Machining parameter

#8018 G84/G74n #8054 W Axis parameter #8204 OT-CHECK-N #8205 OT-CHECK-P #8206 TOOL CHG.P #8209 G60 Shift Barrier data #8300 #8306, #8311 #8314 Basic specification parameter

#1084 RadErr

#8004 SPEED is 10 inches/min. unit for the inch system.

5. Base Specifications Parameters

II - 29

# Items Details Setting range (unit)

1050 (PR)

MemPrg Definition of program save area

Setting 0 1 2 3

Machining program

MDI data

(Machining program) : System common

Machining program save area is shared by systems.

: System independent Machining programs can be registered for each system.

(MDI data)

: System common MDI data is shared by systems.

: System independent MDI data can be set for each system.

When this parameter is changed, the power must be turned OFF and ON, and the system formatted. (Note) This parameter is valid when #1001

SYS_ON[2] is 1.

0 to 3

1051 (PR)

MemTol Tool compensa- tion memory common for systems

0: Tool compensation memory separate for systems

1: Tool compensation memory common for systems

0/1

1052 (PR)

MemVal No. of common variables shared in system designation

0: Common variables common for system (number fixed)

#100 to : Per system #500 to : Common for systems 1: Common variables common for system

(number fixed) #100 to : Designate with V1comN #500 to : Designate with V0comN

* When this parameter is changed, the method of reading the file system will change after the power is turned ON, so always reformat again. Setting order

MemVal change- over

Format Mismatch displays

Format

Turn power ON again

0/1

5. Base Specifications Parameters

II - 30

# Items Details Setting range (unit)

1060 SETUP Activate setup processing

Execute the functions required for initializing the system.

1: Execute one-touch setup

#(1060) Data( 1)( )

"BASE PARA. SET? (Y/N)" is displayed.

To initialize the parameters.

The parameters are initialized according to the setting values in #1001 to #1043.

To retain the current parameters.

"FORMAT?(Y/N)" is displayed.

To initialize the machining program file and tool offset file.

The above files are initialized and the standard canned cycle program is input.

To retain the current machining program file and tool offset file.

"SETUP COMPLETE" is displayed.

INPUT

INPUT

INPUT

INPUT

INPUT

N

N

Y

Y

Note: Most setup parameters will be initialized with

one-touch setup so confirm the data before executing.

This parameter will automatically be set to 0 when the power is turned ON.

1

5. Base Specifications Parameters

II - 31

(SETUP PARAM 1. 3/15)

# Items Details Setting range (unit) 1061 (PR)

intabs Manual ABS updating

Defines whether to update the absolute value data during automatic handle interrupt. This parameter is valid only when #1145 l_abs is set to 1.

0: Do not update (shift coordinates the amount of the interruption)

1: Update (same coordinates as when interrupt did not occur will be applied.)

1062 T_cmp Tool offset function

Specify whether the tool length offset and wear compensation is valid during T command execution.

0 to 3

1063 mandog Manual dog-type

The initial return to the reference point is performed with dog-type return after the power is turned ON and the coordinate system is established. Specify the manual reference point return method after the coordinate system is established with this parameter. (This setting is not required when using absolute position detection.)

0: High speed return 1: Dog-type

1064 (PR)

svof Error correction

Specify whether to correct the error when the servo is OFF.

0: Do not correct the error

1: Correct the error

Setting value Tool length offset Wear compensation 0 Valid Valid 1 Valid Invalid 2 Invalid Valid 3 Invalid Invalid

5. Base Specifications Parameters

II - 32

# Items Details Setting range (unit)

1065 JOG_H JOG response type

Set up an improved JOG response type. 0: Conventional specification The system is started and stopped by signal

via ladder without reference to external input signals.

1: Type 1 The system is started up and stopped by

external signal. 2: Type 2 The system is started up and stopped by

performing the AND operation for external signals and those via ladder.

3: Type 3 The system is started up when signals via

ladder rise. It is stopped when external signals and those via ladder fall.

4: Type 4 Zero point return mode: The system is started

up and stopped by signal via ladder without reference to external input signals (conventional specification).

Non-zero point return mode: The system is started up and stopped by performing AND for external signals and those via ladder (type 2).

0 to 4

1066 JOG_HP Select JOG activation (+) device

Specify the number of the device that inputs +JOG activation signals. The device type is specified by JOG_D in #1071. The effective range of set values vary depending on the device type. A value outside of the effective range is invalid if specified.

X: 0000 to 013F (hexadecimal)

G: 0000 to 3071 M: 0000 to 5119

(decimal) 1067 JOG_HN Select JOG

activation () device

Specify the number of the device that inputs -JOG activation signals. The device type is specified by JOG_D in #1071. The effective range of set values vary depending on the device type. A value outside of the effective range is invalid if specified.

X: 0000 to 013F (hexadecimal)

G: 0000 to 3071 M: 0000 to 5119

(decimal) 1068 (PR)

slavno Slave axis number

Specify the number of the slave axis for synchronous control. The axis number is an NC number excluding the spindle and PLC axis. Two or more slave axes cannot be set up for one master axis. slaveno cannot be set up for a slave axis. A dual system cannot be set up so that the relationship between the master and slave axes extends over a system.

0: No slave axis 1 to 4: First to fourth

axes 1 to 14: 1st axis to 14th

axis (For simple C axis

synchro- nous control)

5. Base Specifications Parameters

II - 33

# Items Details Setting range (unit)

1069 (PR)

no_dsp Axis with no counter display

Set up an axis that displays no counter. This option is valid on the counter display screen (relative value screen).

0: Displays the counter

1: Does not display the counter.

1070 axoff Axis removal

Define an axis that enables axis removal control. 0: Disables axis removal.

1: Enables axis removal

1071 (PR)

J0G_D J0G activation signal device name

Specify the number of the device that inputs J0G activation signals.

0: X device 1: G device 2: M device

Set the JOG_HP (#1066) and JOG_HN (#1067) parameters according to this device specification parameter.

0 to 2

1072 chop_ax Chopping axis

Designate the chopping axis. 0: Non-chopping axis

1: Chopping axis

5. Base Specifications Parameters

II - 34

(SETUP PARAM 1. 4/15)

# Items Details Setting range (unit) 1073 I_Absm Initial

absolute value

Specify the absolute value/incremental value mode for when the power is turned ON or reset.

0: Incremental value command mode

1: Absolute value command mode

1074 l_Sync Initial synchronous feed

Specify the feedrate specification mode for when the power is turned ON or reset.

0: Asynchronous feed (feed per minute) 1: Synchronous feed (feed per rotation)

0: Asynchronous feed

1: Synchronous feed

1075 I_G00 Initial G00 Specify the linear command mode for when the power is turned ON or reset.

0: Linear interpolation (G01 command state) 1: Positioning (G00 command state)

0: Linear interpolation

1: Positioning

1076 Abslnc (For L system only)

ABS/INC address

The absolute value/incremental commands can be issued by using the absolute value address and incremental value address for the same axis.

0: Absolute/incremental with G command 1: Absolute/incremental with address code (The #1013 axname address will be the

absolute value command and #1014 incax address will be the incremental value command)

0: Absolute/ incremental with G command

1: Absolute/ incremental with address code

1077 radius Incremental command for diameter specification axis

Specify if the diameter specification axis (#1019 dia is set to 1) incremental value command uses the diameter value or radius value

0: Diameter value 1: Radius value

1078 Decpt2 Decimal point type 2

Specify the unit of position commands that do not have a decimal point.

0: The min. input command unit is used (follows #1015 cunit)

1: 1mm (or 1inch) unit is used (For the dwell time, 1s unit is used.)

0: The min. input command unit is used

1: 1mm (or 1inch) unit is used

1079 F1digt Validate F1 digit

Specify whether to execute the F command with a 1-digit code command or with a direct numerical command.

0: Direct numerical command (command feedrate during feed per minute or rotation)

1: 1-digit code command (feedrate specified with #1185 spd_F1 #1189 F5)

0: Direct numerical command

1: 1-digit code command

1080 Dril_Z (For D system only)

Specify boring axis

Specify a fixed cycle hole drilling axis. 0: Use an axis vertical to the selected plane as

the hole drilling axis. 1: Use the Z axis as the hole drilling axis

regardless of the selected plane.

0/1

5. Base Specifications Parameters

II - 35

# Items Details Setting range (unit)

1081 Gmac_P Give priority to G code parameter

Specify the G code priority relationship during the macro call with the G command.

0: G code used in system is priority. 1: Registered G code for call out is priority.

0/1

1082 Geomet (For L system only)

Geometric Specify whether to use the geometric I or IB function.

0: Do not use. 1: Use only geometric I. 2: Use geometric I and IB.

With geometric, specific address codes are used for exclusive meanings. Thus, if A or C is used for the axis address or 2nd miscellaneous command code, the A used for the axis address may function as the geometric's angle designation. Take special care when designating the axis name, etc., when using this function.

0/1/2

1084 RadErr Arc error Specify the tolerable error range when a deviation occurs in the end point and center coordinate in the circular command.

0 to 1.000 (mm)

1085 G00Drn G00 dry run Specify whether to apply dry run (feed with manual setting speed instead of command feedrate) to the G00 command.

0: Do not apply to G00. (move at rapid traverse rate)

1: Apply to G00. (move at manual set feedrate)

0: Do not apply to G00

1: Apply to G00

1086 G0lntp G00 non-interpol ation

Specify the G00 movement path type 0: Move linearly toward the end point.

(interpolation type) 1: Move to the end point of each axis at the rapid

traverse feedrate for each axis. (non-interpolation)

0/1

1087 G96_G0 Constant surface speed control by rapid traverse feed command

Specify how to handle the cycle speed for the G00 command when using the constant surface speed control function.

0: Calculate the cycle speed constantly even during G00 movement.

1: Calculate the cycle speed at the block end point in the G00 command.

0/1

1088 G30SL Disable G30 soft limit

Specify how to handle the soft limit during G30 (2nd reference point return) movement.

0: Soft limit valid during G30 movement 1: Soft limit invalid during G30 movement

0: Soft limit valid 1: Soft limit invalid

1089 Cut_RT Short cut for rotary axis

Specify how to handle the short cut control for the rotary axis (#1017 rot is set to 1).

0: No short cut (move toward end point) 1: Use short cut (when using the absolute value

command move in the direction where the movement amount will be 180 or less)

0: No short cut 1: Use short cut

5. Base Specifications Parameters

II - 36

# Items Details Setting range (unit)

1090 Lin_RT Linear rotary axis

Specify how to handle a command for the rotary axis that exceeds 360.

0: For absolute value commands that exceed 360 the value will be converted into a remainder of 360 and the axis will move. Example: If the command is 420 the applied

value will be 60. 1: For absolute value commands that exceed

360 the axis will move in the same manner as a linear axis. Example: If the command is 420 the axis will

pass the 360 position and will move to the 60 position.

0/1

1091 Mpoint Ignore middle point

Specify now to handle the middle point during G28 and G30 reference point return.

0: Move to the reference point after passing the middle point designated in the program.

1: Ignore the middle point designated in the program and move straight to the reference point.

0/1

1092 Tchg _A Replace tools for additional axis

Specify the movement of the additional axis during tool change position return.

0: The additional axis does not move with the tool change position return command.

1: After returning the standard axis with the tool change position return command the additional axis also returns to the tool change position.

0/1

1093 Wmvfin Inter-system waiting method

Specify the method for waiting between systems when using two systems. When the movement command is found in the wait command (!, M) block:

0: Wait before executing movement command 1: Wait after executing movement command

0/1

1094 Tl_SBK (for L system only)

Select life count for single block

Select whether to count the data units to be used for a single block when using the tool life management II function (L system).

0: Does not count the data units. 1: Count the data units.

0/1

5. Base Specifications Parameters

II - 37

# Items Details Setting range (unit)

1095 T0tfof TF output Select how to handle TF for T00 command. 0: TF is output. 1: TF is not output

0/1

1096 T_Ltyp (for L system only)

Tool life management type

Specify the tool life management type. 1: Life management type l

2: Life management type ll

1097 T1digt Tool wear compensation number 1-digit command

Specify the No. of digits in the tool wear compensation No. in the T command.

0: The 2 high-order digits are the tool No. and the 2 Iow-order digits are the wear compensation No.

1: The 3 high-order digits are the tool No. and the 1 Iow-order digit is the wear compensation No.

This parameter will be fixed to 0 when tool life management II is selected.

0/1

1098 Tlno. Tool length offset number

Specify the No. of digits in the tool length offset No. in the T command.

0: The 2 or 3 high-order digits are the tool No. The 2 or 1 Iow-order digits are the tool length

offset and wear compensation Nos. 1: The 2 or 3 high-order digits are the tool No.

and tool length offset Nos. The 2 or 1 Iow-order digits are the wear

compensation No.

0/1

1099 Treset Cancel tool wear compen- sation amount

Specify how to handle tool compensation vector when resetting system.

0: Clear the tool length and wear compensation vectors when resetting.

1: Save the tool length and wear compensation vectors when resetting.

When the values are cleared the compensation will not be applied so the axis will move the compensation amount in the next compensation operation. When the values are saved the compensation will be applied so the axis will shift the differential amount of the compensation amount in the next compensation operation.

0: Clear 1: Save

5. Base Specifications Parameters

II - 38

# Items Details Setting range (unit)

1100 Tmove Tool wear compen- sation

Specify the period to perform tool length offset and wear compensation.

0: Compensate when T command is executed. 1: Superimpose and compensate with the

movement command in the block where the T command is located. If there is no movement command in the same block compensation will be executed after the movement command is superimposed in the next movement command block.

2: Compensate when the T command is executed. 1: Superimpose and compensate a tool length offset with the movement command in the same block. If there is no movement command in the same block, compensation will be executed after the movement command is superimposed in the next movement command block.

0 to 2

1101 Tabsmv Tool wear compen- sation method

Specify the type of movement command when #1100 Tmove is set to 1.

0: Compensate regardless of the movement command type.

1: Compensate only at the movement command in the absolute value command.

0: Compensate regardless of the command type.

1: Compensate only with the absolute value command.

1102 tlm (For L system only)

Manual tool length measuring system

Specify the measurement method for manual tool measurement l.

0: Align tool with reference position 1: Input measurement results

0: Reference position method

1: Measured value input method

1103 T_life Validate life management

Select the usage of the tool life management function.

0: Do not use. 1: Perform tool life

management control.

1104 T_Com2 Tool command method 2

Select the command method for when #1103 T_Life is set to 1.

0: Handle the program tool command as the group No.

1: Handle the program tool command as the tool No.

0/1

5. Base Specifications Parameters

II - 39

# Items Details Setting range (unit)

1105 T_Sel2 Tool selection method 2

Select the tool selection method for when #1103 T_Life is set to 1.

0: Select in order of registered No. from the tools used in the same group.

1: Select the tool with the longest remaining life from tools used in the same group and the unused tools.

0/1

1106 Tcount (For L system only)

Life management count

Specify the function when address N is omitted when inputting data (G10 L3 command) for tool life management function ll.

0: Time specified input

1: No. of times specified input

1107 Tllfsc (For L system only)

Split life management display screen

Set up the number of groups to be displayed on the tool life management II (L system) screen.

0: Displayed group count 1, maximum number of registered tools: 16

1: Displayed group count 2, maximum number of registered tools: 8

2: Displayed group count 4, maximum number of registered tools: 4

0 to 2

1108 TlrectM (For L system only)

Life management re-count M code

Set up the M code for tool life management II (L system) re-count.

0 to 99

1109 (PR)

subs_M Validate alternate M code

Select the user macro interrupt with the substitute M code.

0: Alternate M code invalid

1: Alternate M code valid

1110 M96_M M96 alternate M code

Specify an M code to replace M96 when #1109 subs_M is set to 1.

3 to 97 (excluding 30)

1111 M97_M M97 alternate M code

Specify an M code to replace M97 when #1109 subs_M is set to 1.

3 to 97 (excluding 30)

1112 (PR)

S_TRG Validate status trigger system

Specify the validity conditions for the user macro interrupt signal.

0: Valid when interrupt signal (UIT) turns OFF to ON.

1: Valid when interrupt signal (UIT) is ON.

0: Valid when interrupt signal (UIT) turns OFF to ON.

1: Valid when interrupt signal (UIT) is ON.

1113 (PR)

INT_2 Validate interrupt method type 2

Specify the movement after user macro interrupt signal (UIT) input.

0: Execute interrupt program without waiting for block being executed to end.

1: Execute interrupt program after completing block being executed.

0/1

5. Base Specifications Parameters

II - 40

# Items Details Setting range (unit)

1114 mcrint Macro argument initialization

Select whether to clear statements other than specified arguments by macro call. Also, select whether to clear local variables by power-ON and resetting.

0: Delete non-specified arguments by macro call.

1: Retain non-specified arguments by macro call.

2: Retain non-specified arguments by macro call and clear local variables by power-ON and resetting.

0/1/2

1115 thwait Waiting for thread cutting

Set the queue number during screw thread cutting when the chamfering is not valid.

0 to 99 (Approx. 4 ms.) Standard set value: 4

1116 G30SLM Invalidate soft limit (manual operation)

Enable this function when disabling the soft limit check function from the second to the fourth zero point return by manual operation.

0: Enable soft limit function.

1: Disable soft limit function.

1117 H_sens Handle response switch

Switch the handle response mode when feeding the handle.

0: Standard handle response 1: High-speed handle response

0/1

1118 mirr_A (For L system only)

Select how to set up the length of tools on cutter tables (opposed tables)

Select one of the following two methods: Set up the current length of tools on each

facing turret. Set up a value, assuming that the tools on

each facing turret are in the same direction as that of those on the base turret.

0: Current length of the tools on each facing turret

1: Value, assuming that the tools on each facing turret are in the same direction as that of those on the base turret.

0/1

1119 Tmiron (For L system only)

Select the mirror image of each facing turret with T command

Select whether to validate the mirror image of each facing turret with the T command.

0: Invalid 1: Valid

1120 (PR)

TofVal Change macro variable

Specify whether to change the macro variable (tool offset) numbers for shape compensation and wear compensation.

0: Do not change. (Conventional specifications)

1: Change the shape and wear compensation variable numbers each for X, Z, and R.

0/1

5. Base Specifications Parameters

II - 41

(SETUP PARAM 1. 5/15)

# Items Details Setting range (unit) 1121 edlk_c Edit lock C Specify whether to prohibit editing of program Nos.

9000 to 9999. Note: If #1122 is set to 1 or 2, 1 will be set in #1121

when the power is turned ON.

0: Editing possible 1: Editing prohibited

1122 (PR)

pglk_c Program display lock

The display and search of program Nos. 9000 to 9999 can be prohibited. Specify whether to prohibit display and search.

0: Display and search is possible. 1: Program details are not displayed. 2: Program details are not displayed and

operation search is prohibited. The program details will not be displayed but the program No. and sequence No. will display in the prohibited state. Note: If #1122 is set to 1 or 2, 1 will be set in #1121

when the power is turned ON.

0 to 2

1123 origin Origin zero inhibition

Select whether to use the origin zero function. 0: Use 1: Do not use

1124 ofsfix Fix tool wear compen- sation number

Specify whether to automatically increment the offset No. by 1 with the input or to display the No. as it is in the setting on the tool offset screen.

0: Increment the # No. by 1 when the input key is pressed. (Same as general parameters)

1: # No. does not change even if INPUT key is pressed.

When making settings in sequence 0 is handier. When changing and setting repeatedly while adjusting one offset value 1 is handier

0/1

1125 real_f Actual feedrate display

Specify the feedrate display on the monitor screen. 0: Command speed 1: Real movement

feedrate 1126 PB_G90 Playback G90 Specify whether the playback movement amount

when performing playback editing is to be an absolute value or incremental value.

0: Incremental value 1: Absolute value

1127 DPRINT DPRINT alignment

Specify the alignment for printing out with the DPRINT function.

0: No alignment data is printed with left justification.

1: Align the minimum digit and output.

0/1

5. Base Specifications Parameters

II - 42

# Items Details Setting range (unit)

1128 RstVCI Clear variables by resetting

Specify how to handle the common variables when resetting.

0: Common variables do not change after resetting.

1: The following common variables are cleared by resetting: During variable 100 group specifications: #100

to #149 are cleared. During variable 200 group and 300 group

specifications: #100 to #199 are cleared.

0/1

1129 PwrVCl Clear variables by power-ON

Specify how to handle the common variables when the power is turned ON.

0: The common variables are in the same state as before turning the power OFF.

1: The following common variables are cleared when the power is turned ON. During variable 100 group specifications: #100

to #149 are cleared. During variable 200 group and 300 group

specifications: #100 to #199 are cleared.

0/1

1130 set_t Display selected tool number

Specify the tool command value display on the POSITION screen.

0: T-modal value of program command is displayed.

1: Tool number sent from PLC is displayed.

0/1

1131 (PR)

Fldcc Feed forward filter

Parameter to suppress acceleration changes with a filter when starting acceleration or deceleration Specify the parameter in bits.

3 0125 46 7

Feed forward filter

bit1: 7.1 (ms) bit2: 14.2 (ms) bit3: 28.4 (ms) bit4: 56.8 (ms) bit5: 113.6 (ms) If bit 1 to bit 5 are all 0 or two or more bits of bit 1 to bit 5 are 1, 3.5 ms is set up.

1132 CRT CRT brightness control

This parameter adjusts the brightness of the CRT display unit.

3: Highest luminance (Brightest state) 3: Lowest luminance (Darkest state)

Adjust this parameter to an appropriate brightness between 3 and 3. The EL display unit does not have brightness adjustment so setting is not required.

3 to 3

5. Base Specifications Parameters

II - 43

# Items Details Setting range (unit)

1133 ofsmem Select how to set up tool wear compensa- tion screen

Select the number stored by previous setup when selecting the tool wear compensation screen.

0: Does not display the number when selecting the screen.

1: Displays the stored number when selecting the screen.

0/1

1134 LCDneg LCD reverse display

Specify 1 to reverse the display on the 10.4-type monochrome LCD.

0: Normal display 1: Reverse display

1135 unt_nm Unit name Set up a unit name. Set up the unit name with 4 or less characters consisting of both alphabets and numbers. If 0 is set up, the unit name is not displayed.

4 or less characters consisting of both alphabets and numbers

1136 optype Operation menu display valid

This parameter validates the operation menu display. Specify the setting method for the tool offset datas absolute value or incremental value.

0: Mode selection method (Conventional specification)

1: Menu selection method This parameter is valid on the following screens. TOOL TIP OFFSET screen (L system) TOOL DATA screen (L system) NOSE-R screen (L system) TOOL OFFSET screen type I (M system) TOOL OFFSET screen type II (M system)

0/1

1137 Cntsel Coordinate value screen display counter select

Set the type of the position counter to be displayed on the COORDINATE screen.

0 : MST (Default)

1 : Next command

2 : Current value B

3 : Manual interrupt amount

0 or 1 : Next value (Default)

2 : Current value B

3 : Manual interrupt amount

1st digit : 0 to 3 2nd digit: 0 to 3 (Default : 00)

1138 Pnosel Select screen by parameter number:

Specify whether to enable the function to select a screen by specifying a parameter number.

0: Disable 1: Enable

5. Base Specifications Parameters

II - 44

# Items Details Setting range (unit)

1139 edtype Edit type selection

Set up an edit type. 0: Screen edit type (M50 or equivalent operation) 1: Screen edit type (The screen of EDIT or MDI is

changed automatically according to the selected operation mode.)

2: Word edit type (The screen of EDIT or MDI is changed automatically according to the selected operation mode.)

3: Screen edit type (type 0 + retaining cursor position) (Applicable only to M64 D version series)

4: Screen edit type (type 1 + retaining cursor position) (Applicable only to M64 D version series)

0/1/2/3/4

1140 Mn100 M code number

First number of M code that corresponds to setup number from 100 to 199

0 to 99999999

1141 Mn200 M code number

First number of M code that corresponds to setup number from 200 to 299

0 to 99999999

1142 Mn300 M code number

First number of M code that corresponds to setup number from 300 to 399

0 to 99999999

1143 Mn400 M code number

First number of M code that corresponds to setup number from 400 to 499

0 to 99999999

1144 mdlkof MDI setup lock

Select whether to enable MDI setup in non-MDI mode. 0: Disable MDI setup 1: Enable MDI setup

1145 I_abs Manual ABS parameter

Specify how to handle the absolute value data during automatic handle interrupt.

0: Absolute value data is renewed if manual ABS switch is ON.

Data is not renewed if switch is OFF. 1: Follows the intabs state when #1061 intabs is

valid.

0/1

1146 Sclamp Spindle rotation speed clamp function

Specify how to handle the spindle rotation speed clamp function with the G92S command.

0: G92S command is handled as a clamp command only in the G96 state (during constant surface speed control). G92S will be handled as normal S command in G97 state (constant surface speed OFF).

1: The S command in the same block as G92 is constantly handled as a clamp command.

0/1

1147 smin_V Minimum spindle rotation speed clamp type

Specify the type of spindle min. rotation speed clamp value.

0: Rotation speed setting 1: Output voltage coefficient setting

Set the #3023 smini parameter according to this type setting.

0/1

5. Base Specifications Parameters

II - 45

# Items Details Setting range (unit)

1148 I_G611 Initial high precision

The modal state when the power is turned ON is set to the high accuracy control mode.

0: OFF 1: ON

0/1

1149 cireft Arc deceleration speed change

Specify whether to enable deceleration at the arc entrance or exit.

0: Disable 1: Enable

0/1

1150 Fldc0 G00 feed forward filter

This parameter is used to filter acceleration changes at the start of rapid acceleration/deceleration. Specify the filters in bit units.

3 0125 46 7

Feed forward filter G00/G01 separation

G00 feed forward filter

0: Common 1: Separation

bit1: 7.1 (ms) bit2: 14.2 (ms) bit3: 28.4 (ms) bit4: 56.8 (ms) bit5: 113.6 (ms) When bits 1 to 5 are all 0 or when two or more of bits 1 to 5 are 1, 3.5 (ms) is assumed.

1151 rstint Reset initial Specify whether to initialize (power ON state) the modals by resetting.

0: Do not initialize modal state. 1: Initialize modal state.

0/1

1152 I_G20 Initial command unit

Specify whether the default mode after power-ON or resetting, inch command or metric command mode.

0: Metric command (G21 command state) 1: Inch command (G20 command state) Valid when reset input is made.

Related parameter: Bit 6 Select setting and display unit of #1226

0/1

1153 FixbDc Hole bottom deceleration check

Specify whether to perform a deceleration check or in-position check at the hole bottom in the hole drilling cycle. This parameter is valid only for a hole drilling cycle in which no dwell command can be issued at the hole bottom.

0: Perform no deceleration check and in-position check.

1: Perform a deceleration check. 2: Perform an in-position check.

0 to 2

5. Base Specifications Parameters

II - 46

# Items Details Setting range (unit)

1154 (PR)

pdoor Door interlock II (for each system)

Specify whether to control door interlock II independently for each of the two systems. When door interlock II is controlled for each system of the two systems, system 1 is connected to SV1 (channel 1) of the base I/O unit and system 2 is connected to SV2 (channel 2) of the base I/O unit. Base I/O unit

SV1 SV2

AMPAMP AMP System 1

AMPAMP AMP System 2

When the auxiliary axis (MR-J2-CT) is used, connect it to the SV2 side (after the spindle). This validates door interlock II of system 2.

0: Do not use door interlock II independently for channels.

1: Use door interlock II independently for channels. (Separate systems when using two systems) 2: Use door interlock II independently for channels. (Use independently for system 1 channels) (Use both for system 2)

When 0 is specified for this parameter, Signal input device 1 for door interlock II (#1155 DOOR_m) and Signal input device 2 for door interlock II (#1156 DOOR_s) are valid. When 1 is specified, Signal input device 1 for door interlock II: for each system (#1511 DOORPm) and Signal input device 2 for door interlock II: for each system (#1512 DOORPs).

0/1

5. Base Specifications Parameters

II - 47

# Items Details Setting range (unit)

1155 DOOR_m Signal input device 1 for door interlock II

Set up a fixed device number (X??) for door interlock II signal input. A device number from X01 to XFF can be set up. Device number 000 is invalid. Set up device number 100 when using no fixed device number for door interlock II signal input. Related parameter: #1154 pdoor Door interlock II

(for each system)

000 to 100 (Hexadecimal)

1156 DOOR_s Device number 2 for door interlock II signal input

Set up a fixed device number (X??) for door interlock II signal input. (Set up the same value as that of #1155.) Related parameter: #1154 pdoor Door interlock II

(for each system)

000 to 100 (Hexadecimal)

1157 F0atrn F0 automatic running

Not used

1158 F0atno F0 automatic running program

Not used

1165 p_trans Parameter FROM backup

The parameters are written, read and compared. 0: No process 1: The backed up parameters are read from the

FROM. 2: The parameters are written into the FROM. 3: The parameters are compared with those

backed up in the FROM.

0 to 3

1166 fixpro Fixed cycle editing

Select whether to use the edit, program list and data input/output functions for the fixed cycles, machine manufacturer macro programs or general programs.

0: General programs can be edited, etc. 1: The fixed cycles can be edited, etc.

Password No.: The machine manufacturer macro programs can be edited, etc.

0 to 99999999

1167 e2rom Not used. 1168 test Simulation

test Specify the test mode for the control unit. The test mode does not use reference point return and tests with a hypothetical zero point return completed state. This is limited to test operation of the control unit itself and must not be used when connected to the machine.

0: Normal operation mode

1: Test mode

5. Base Specifications Parameters

II - 48

(SETUP PARAM 1. 6/15)

# Items Details Setting range (unit) 1169 system

name System name Set the name of each system.

This must be set only when using two systems. This name is displayed on the screen only when the systems must be identified. Use a max. of four alphabetic characters or numerals.

A max. of four alphabetic characters or numerals.

1170 M2name Second miscellane- ous code

Set this address code when using the 2nd miscellaneous command. Set an address with A B and C that is not used with #1013 axname or #1014 incax.

A, B, C

1171 taprov Tap return override

Set the tap return override value for the synchronous tap.

1 to 100 (%)

1172 tapovr Tap return override

Set the override value when leaving the tap end point in the synchronous tap cycle. The setting range is 1 to 999 and the unit is %. When a value less than 100 is set it will be judged as 100%.

1 to 999 (%)

1173 dwlskp G04 skip condition

Specify the skip signal for ending the G04 (dwell) command.

Skip condition 0 to 7

0 1 2 3 4 5 6 7

Skip 1 Skip 2Skip 3

Set- ting

PLC interface input signal

End when signal is input.

1174 skip_F G31 skip speed

Specify the feedrate when there is no F command in the program at G31 (skip) command.

1 to 999999 (mm/min)

1175

1176

1177

1178

1179

1180

skip1 1f 2 2f 3 3f

G31.1 skip condition G31.2 skip speed G31.2 skip condition G31.2 skip speed G31.3 skip condition G31.3 skip speed

Specify the skip signal in the G31.1 to G31.3 (multi-step skip) command and the feedrate when there is no F command in the program. Skip signal specified at G31.1 Skip feedrate at G31.1 Skip signal specified at G31.2 Skip feedrate at G31.2 Skip signal specified at G31.3 Skip feedrate at G31.3

Skip condition 0 to 7

0 1 2 3 4 5 6 7

Skip 1 Skip 2Skip 3

Set- ting

PLC interface input signal

Skip feedrate 1 to 999999 (mm/min)

5. Base Specifications Parameters

II - 49

# Items Details Setting range (unit)

1181 G96_ax Constant surface speed control

Specify the axis to be targeted for constant surface speed control.

0: Program specification will be invalidated and the axis will always be fixed to the 1st axis.

1: 1st axis specification 2: 2nd axis specification 3: 3rd axis specification : : 8: 8th axis specification

The program specification will be the priority for all settings other than 0.

0 to 8

1182 thr_F Thread cutting speed

Set the screw cut up speed when not using chamfering in the thread cutting cycle.

0: Cutting feed clamp feedrate 1 to 60000 mm/min: Set feedrate

0 to 60000 (mm/min)

1183 clmp_M M code for clamp

Set the M code for C-axis clamp in the hole drilling cycle.

0 to 99999999

1184 clmp_D Dwelling time after outputting M code for unclamp

Set the dwell time after outputting the M code for C-axis unclamp in the hole drilling cycle.

0.000 to 99999.999 (s)

1185 1186 1187 1188 1189

spd_F1 spd_F2 spd_F3 spd_F4 spd_F5

F1 digit feedrate F1 F2 F3 F4 F5

Specify the feedrate for the F command in the F1-digit command (#1079 F1 digt is set to 1). Feedrate when F1 is issued (mm/min) Feedrate when F2 is issued (mm/min) Feedrate when F3 is issued (mm/min) Feedrate when F4 is issued (mm/min) Feedrate when F5 is issued (mm/min)

1 to 60000 (mm/min)

1190 (PR)

s_xcnt (For L system only)

Validate inclined- axis control

Specify whether to disable or enable inclined-axis control.

0: Disable inclined-axis control 1: Enable inclined-axis control

0/1

1191 (PR)

s_angl (For L system only)

Inclination angle

Specify the inclination angle (). Note: If 0 is specified for this parameter, the angle

determined by three-side setting is valid.

80.000 ()

1192 (PR)

s_zrmv (For L system only)

Compensa tion at origin return

Specify whether to perform compensation for the base axis corresponding to the inclined axis at original return.

0: Perform compensation. 1: Don't perform compensation.

0/1

5. Base Specifications Parameters

II - 50

(SETUP PARAM 1. 7/15)

# Items Details Setting range (unit) The setting is selected with "#1306 InpsTyp Deceleration check specification type".

0: Deceleration check method 1 1: Validate in-position check

Deceleration check method 1

Specify the deceleration check method for G0. 0: Command deceleration check 1: In-position check

0/1

1193 inpos

Validate in-position check

Specify the deceleration confirmation method for the positioning or cutting command.

0: G0, G1+G9 Command deceleration check 1: G0, G1+G9 In-position check

0/1

1194 H_acdc Time constant 0 for handle feed

Specify the time constant for the manual handle feed.

0: Use time constant for G01 1: Time constant 0 (step)

0/1

1195 1196 1197 1198

Mmac Smac Tmac M2mac

Macro call for M command Macro call for S command Macro call for T command Macro call with 2nd miscellaneous code

Specify the user macro M S or T command macro call out. Macro call out with M command Macro call out with S command Macro call out with T command Macro call out with 2nd miscellaneous command

0: Invalid 1: Valid

1199 Sselect Select initial spindle control

Select the initial condition of spindle control after power is turned ON.

0: 1st spindle control mode (G43.1) 1: Selected spindle control mode (G44.1) 2: All spindle simultaneously control mode

(G47.1) Note: Spindle No. when G44.1 is commanded is

selected with #1534 SnG44.1.

0: G43.1 1: G44.1 2: G47.1

1200 (PR)

G0_acc Validate acceleration and deceleration with inclination angle constant G0

Set up acceleration and deceleration types when a rapid traverse command is issued

0: Acceleration and deceleration (conventional) with time constant

1: Acceleration and deceleration with inclination angle constant

0: Acceleration and deceleration with time constant

1: Acceleration and deceleration with inclination angle constant

5. Base Specifications Parameters

II - 51

# Items Details Setting range (unit)

1201 (PR)

G1_acc Validate acceleration and deceleration with inclination constant G1

Set up acceleration and deceleration types when a liner interpolation command is issued.

0: Acceleration and deceleration (conventional) with time constant

1: Acceleration and deceleration with inclination angle constant

0: Acceleration and deceleration with time constant

1: Acceleration and deceleration with inclination angle constant

1202 mirofs (For L system only)

Distance between facing turrets

Set up the distance between tools (edges) (between facing turrets).

0 to 99999.999 (mm)

1203 TmirS1 (For L system only)

Select turrets as facing turrets with T command

Set up turrets as shown in the mirror image of facing turrets with the T command that corresponds to tool numbers 1 to 32.

0 to FFFFFFFF

1204 TmirS2 (For L system only)

Select turrets as facing turrets with T command

Set up turrets as shown in the mirror image of facing turrets with the T command that corresponds to tool numbers 33 to 64.

0 to FFFFFFFF

1205 G0bdcc Acceleration and deceleration before G0 interpolation

0: G00 acceleration and deceleration are selected as those after interpolation.

1: The G00 acceleration/deceleration is the acceleration/decelerate before interpolation regardless of whether the mode is the high accuracy control mode.

(Note) "1" cannot be set for the 2nd system.

0/1

1206 G1bF Maximum speed

Set up a cutting feedrate when selecting acceleration and deceleration before interpolation.

1 to 999999 (mm/min)

1207 G1btL Time constant Set up a cutting feed time constant when selecting acceleration and deceleration before interpolation.

G1bF

G1btL Time

Speed

1 to 5000 (ms)

1208 RCK Arc radius error compen- sation factor

An arc radius error compensation can be increased and decreased from 60.0 to 20.0%.

-60.0 to +20.0 (%)

5. Base Specifications Parameters

II - 52

# Items Details Setting range (unit)

1209 cirdcc Arc decelerati on speed

Specify the deceleration speed at the arc entrance or exit.

1 to 999999 (mm/min)

1210 RstGmd Modal G code reset

Specify whether to initialize each G code group modal and the H and D codes when the system is reset. Specify the initialization items in bit correspondence. 0. Initialize. 1: Don't initialize. M system

Specify a hexadecimal number.

The H code indicates the tool length offset number, and the D code indicates the tool radius compensation number. When bit 18 is set to ON, the H and D codes and group 8 G modal area retained. When bit 7 is set to ON, the H code and group 8 G modal are retained. (To be continued to the next page)

10 Group 17 Constant surface speed control command modal 11 Group 18 pole coordinate command modal 12 Group 19 G command mirror modal 13 Group 20 Spindle 2 control modal 14 15 16 17 18 H, D codes 19 Spindle clamp rotation speed 1A 1B 1C 1D 1E 1F

0 Group 1 Move G modal 1 Group 2 Flat selection modal 2 Group 3 Absolute/increment command modal 3 4 Group 5 Feed G modal 5 Group 6 Inch/metric modal 6 Group 7 Radius compensation modal 7 Group 8 Length compensation modal 8 9 Group 10 Fixed cycle return command modal A B Group 12 Workpiece coordinate system modal C Group 13 Cut modal D E Grpup 15 Normal line control modal F

5. Base Specifications Parameters

II - 53

# Items Details Setting range (unit) (Continued from the previous page)

L system

Specify a hexadecimal number.

1211 FHtyp Feed hold stop type

Specify the type of the external signal used for feed hold.

0: Disable the external signal. 1: Enable the external signal (contact A) 2: Enable the external signal (contact B)

0 to 2

1212 FHno Feed hold external signal device

Specify the number (X??) of the device used to input the feed hold signal.

000 to 13F (hexadecimal)

1213 proaxy (For L system only)

Side 1 of inclination angle

Specify the length on the rectangular coordinates of the inclined axis in the triangle made up of the inclination angle.

9999.999

0 Group 1 Move G modal 1 Group 2 Flat selection modal 2 Group 3 Absolute/increment command modal 3 Group 4 Barrier check modal 4 Group 5 Feed G modal 5 Group 6 Inch/metric modal 6 Group 7 Nose R compensation modal 7 8 9 Group 10 Fixed cycle return command modal A B Group 12 Workpiece coordinate system modal C Group 13 Cut modal D E F

10 Group 17 Constant surface speed control command modal 11 Group 18 Balance cut 12 13 Group 20 Spindle 2 control modal 14 Group 15 Facing turret mirror image 15 16 17 18 19 1A 1B 1C 1D 1E 1F

5. Base Specifications Parameters

II - 54

# Items Details Setting range (unit)

1214 macaxy (For L system only)

Side 2 of inclination angle

Specify the length of the actual base axis corresponding to the inclined axis in the triangle made up of the inclination angle.

9999.999

1215 macaxx (For L system only)

Side 3 of inclination angle

Specify the length of the actual axis of the inclined axis in the triangle made up of the inclination angle.

9999.999

1216 extdcc External deceleration level

Use an upper limit value at the feedrate indicated when validating external deceleration signals. This parameter is valid when #1239 set11/bit6 is set to 0.

1 to 999999 (mm/min)

5. Base Specifications Parameters

II - 55

(SETUP PARAM 1. 8/15)

# Items Details Setting range (unit) 1217 aux01 Not used 1218 aux02

(bit3) Parameter input/output format

Specify a parameter input/output format. 0: Type I 1: Type II (related to #1218 aux02/bit5)

0/1

aux02 (bit4)

Tool number selection

Specify the R register that contains the tool number used for automatic calculation when measuring the coordinate offset of an external workpiece.

0: Conforms to #1130 set_t. 1: Uses the tool number indicated by user PLC

0/1

aux02 (bit5)

Parameter I/O II spindle specification address

Specify the spindle specification address of parameter I/O type II.

0: C 1: T

This parameter also applies to the spindle specification address for input and collation. Note: This parameter is valid only for parameter I/O

type II (bit 3 of aux02 in #1218 is 1).

0/1

aux02 (bit6)

Set No. valid when program input

Specify which program No. is selected when inputting operation using "#1 MAIN PROGRAM" in Data I/O screen.

0: The No. in the input data is valid. 1: The No. set in the data setting area is valid.

0/1

aux02 (bit7)

Input by program overwrite

(1) When inputting operation using "#1 MAIN PROGRAM" in Data I/O screen, select one of the following options when the input program has already been registered:

0: An operation error (E65) occurs. 1: Input by overwrite.

(2) When using the high-speed program server, select the operation if the name of the file to be transmitted with transmission (IC host) operations already exists in the host.

0: Overwrite prohibit 1: Overwrite valid

0/1

1219 aux03 (bit1)

Stop high- speed PC monitoring function

Set 1 to disable the function that stops the system when the high-speed processing time is extended. Disable the monitoring function only as a temporary measure.

0/1

aux03 (bit2)

Improve skip coordinate accuracy

0: Skip accuracy (conventional specification) 1: Changes skip accuracy (correct a position in skip

coordinates when entering skip signals).

0/1

aux03 (bit5)

Dog-type intermediate point

Select whether to move to the intermediate point during automatic dog-type reference point return.

0: Do not move to intermediate point during dog-type reference point return.

1: Move to intermediate point during dog-type reference point return.

0/1

5. Base Specifications Parameters

II - 56

# Items Details Setting range (unit)

1220 aux04 (bit 0) (For L system only)

Tool life check timing selection

Specify the life check standard applicable when the use count is incremented in tool life management II.

0: Determine that the tool life is over when the incremented use count exceeds the life count. (Use count > life count)

1: Determine that the tool life is over when the incremented use count has reached the life count. (Use count life count)

0/1 (Default: 0)

aux04 (bit1)

Validity of space code in comment

Validate or invalidate the space code described in the comment statements in the machining program in edit operation with the special display.

0: Invalidate the space code in the comment statements of the machining program.

1: Validate the space code in the comment statements of the machining program.

0/1 (Default: 0)

aux04 (bit2)

Not used.

aux04 (bit3)

Not used.

aux04 (bit4)

Data input/ output unit selection

Specify the input/output data unit for tool data and user parameter input/output.

0: Internal unit (metric) 1: Follows command mode set with #1152 I_G20 Metric when set to 0 Inch when #1152 I_G20 is

set to 1 This parameter is valid when initial metric (#1041 I_inch 0) is set and the setting and display unit is the command unit (#1226 aux10 bit6 1). In all other cases, the tool data will be input and output with the internal units.

0/1

aux04 (bit7)

Host communication validity during automatic operation

Set whether Ethernet communication is enabled during automatic operation.

0: Ethernet communication disabled during automatic operation

1: Ethernet communication enabled during automatic operation

(Note) If Ethernet communication is enabled during automatic operation, interrupt processes required for communication will be carried out, so the machining performance could be affected.

0/1

5. Base Specifications Parameters

II - 57

# Items Details Setting range (unit)

1221 aux05 (bit7)

Current value B valid

Select the type of counter to be displayed on the POSITION screen.

0: Displays a relative value (value that includes tool length offset amount, tool radius compensation amount and workpiece coordinate offset amount)

1: Displays current value B (value that does not include tool length offset amount, tool radius compensation amount and workpiece coordinate offset amount)

Workpiece offset

Tool offset

aux05/bit7 = 1

aux05/bit7 = 0

(Note1) When "#1221 aux05/bit7" is set to "1", the current value B is selected regardless of the bit type of #1287 ext23. When the current value B is valid, the counter zero or origin zero is invalid.

(Note2) The following limits apply to M64A/M64:

This is compatible only with the lathe system.

The relative value counter on the COORDINATE screen will also display the current value B.

When "#1287 ext23/bit3" is set to 0, the relative value will be displayed instead of the current value B regardless of this parameter setting.

0/1

1222 aux06 (bit0)

Validity of tool length measurement confirmation message

0: Display no confirmation message when tool compensation data is set.

1: Display a confirmation message when tool compensation data is set.

(Applicable only to M64 D version series)

0/1

aux06 (bit1)

Height axis specification

When 1 is set in this parameter, the axis specified by base specification parameter #1028 base_k is measured and no other axes are measured if they move. (Applicable only to M64 D version series)

0/1

5. Base Specifications Parameters

II - 58

# Items Details Setting range (unit) aux06

(bit2) Servo waveform display

Specify whether to enable the waveform display function. (Applicable only to M64 D version series)

0: Disable the waveform display function. 1: Enable the waveform display function.

0/1

aux06 (bit3)

Enable/disable setup parameter lock

Specify whether to enable the setup parameter lock function.

0: Disable 1: Enable

0/1

aux06 (bit4)

Minimum cut-in amount selection

Select the minimum cut-in amount command value for the compound type thread cutting cycle (G76 command) when the minimum cut-in amount (Q) does not exist in 1st block or 1st block is omitted.

0: The minimum cut-in amount (Q) is "0.". 1: The minimum cut-in amount (Q) is the last

command value.

0/1

aux06 (bit5)

Fixed cycle for compound lath command format check selection

Select the operation to be made if the 1st block of the fixed cycle for compound lathe is omitted when the conventional format is selected (#1265 ext01/bit0 "0").

0: Program error (P33) occurs. 1: Parameter setting value is used.

0/1

aux06 (bit7)

Zero point return deceleration check method

Set the deceleration check method used during automatic reference point return. (Applicable only to M64 D version series)

0: In-position check 1: Commanded deceleration check

0/1

1223 aux07 (bit0)

Rapid traverse inclination constant multi-stage acceleration and deceleration

Specify whether to enable the rapid traverse inclination constant multi-stage acceleration/deceleration function. (Applicable only to M64 D version series)

0: Disable 1: Enable

Related parameters: #2064 rapid2 Speed 2 #2065 G0tL2 Time constant 2 #2066 rapid3 Speed 3 #2067 G0tL3 Time constant 3

0/1

aux07 (bit1)

Deceleration check method 2

Select the deceleration check method in G1+G9. 0: Command deceleration check in G1+G9 1: In-position check in G1+G9

The deceleration check is not performed except G1+G9. When #1306 InpsTyp deceleration check specification type is set to 1 (Deceleration check specification type 2), this parameter will be invalid.

0/1

5. Base Specifications Parameters

II - 59

# Items Details Setting range (unit) aux07

(bit2) Synchronous tap R-point in-position check

0: Disable the synchronous tap I-point R-point in-position check.

1: Enable the synchronous tap I-point R-point in-position check.

(Applicable only to M64 D version series) Note: This parameter is valid only when 1 (in-position

check is valid) is set in bit 3 of #1223 aux07 (synchronous tap in-position check improvement).

0/1

aux07 (bit3)

Synchronous tap in-position check improvement

Specify whether to enable the synchronous tap in-position check improvement function. (Applicable only to M64 D version series)

0: Disable 1: Enable

Related parameters: #1223 bit 2 Synchronous tap R-point in-position check bit 4 Synchronous tap hole bottom in-position

check bit 5 Synchronous tap R-point in-position check 2

0/1

aux07 (bit4)

Synchronous tap hole bottom in-position check

0: Disable the synchronous tap hole bottom in-position check.

1: Enable the synchronous tap hole bottom in-position check.

(Applicable only to M64 D version series) Note: This parameter is valid only when 1 (in-position

check is valid) is set in bit 3 of #1223 aux07 (synchronous tap in-position check improvement).

0/1

aux07 (bit5)

Synchronous tap R-point in-position check 2

0: Disable synchronous tape R-point in-position check.

1: Enable synchronous tape R-point in-position check.

(Applicable only to M64 D version series) Note: This parameter is valid only when 1 (in-position

check is valid) is set in bit 3 of #1223 aux07 (synchronous tap in-position check improvement).

0/1

aux07 (bit6)

Cancel synchronous tap (,S) return

0: Retains a spindle rotation speed (, S) when performing synchronous tap return.

1: Cancels a spindle rotation speed (, S) by return with G80.

0/1

aux07 (bit7)

Synchronous tap method

Specify a synchronous tap method. 0: Synchronous tap (multi-step acceleration and

deceleration and rapid return) 1: Conventional type synchronous tap

0/1

1224 aux08 (bit0)

Sampling data output

Set the validity of the sampling data output. 0: Sampling output invalid 1: Sampling output valid

0/1

5. Base Specifications Parameters

II - 60

# Items Details Setting range (unit)

1225 aux09 (bit0)

PLC Interface Diagnosis screen changeover

Set this to change to the PLC Interface Diagnosis screen.

0: 40-character compatible screen 1: 80-character compatible screen

0/1

aux09 (bit7)

Enable/disable spindle rotation speed clamp

Specify whether to enable spindle rotation speed clamp by the spindle rotation speed clamp command (G92S, Q) instead of the spindle rotation speed command (R108) specified by the user ladder.

0: Enable 1: Disable

0/1

1226 aux10 (bit0)

Tool compen- sation data for external workpiece coordinate offset measurement

Select the tool offset data to be used for external workpiece coordinate offset measurement.

0: Tool length data and tool nose wear data 1: Tool length data

0/1

aux10 (bit1)

Optional block skip type

Specify whether to enable optional block skipping in the middle of a block.

0: Enable block skipping only at the beginning of a block.

1: Enable block skipping at the beginning of the block and in the middle of a block.

0/1

aux10 (bit2)

Single block stop timing

Specify the time at which the single block signal is activated.

0: When the signal goes ON while automatic operation is starting, the block stops after it is finished.

1: When the signal is ON at the end of the block, the block stops.

0/1

aux10 (bit3)

C-axis reference point return type

Specify the C-axis reference point return type. 0: Origin return is performed by the G28 reference

point return command or when manual reference point return is activated. The origin dog is used.

1: When the first C-axis command is issued after the C-axis mode is entered in automatic mode, reference point return is performed before execution of the block. Also, reference return is performed by the G28 reference point return command or when manual reference point return is activated. The Z phase of the encoder is used.

0/1

aux10 (bit4)

S command during constant surface speed

Specify whether to output a strobe signal when the S command is issued in constant surface speed mode.

0: Output no strobe signal in constant surface speed mode.

1: Output strobe signals in constant surface speed mode.

0/1

5. Base Specifications Parameters

II - 61

# Items Details Setting range (unit) aux10

(bit5) Arbitrary allocation of dog signal

Specify whether to enable the arbitrary allocation parameter for the origin dog and H/W OT.

0: Disable arbitrary allocation. (Fixed device) 1: Enable arbitrary allocation. (Device specified by

the parameter)

0/1

aux10 (bit6)

Setup and display unit

Specify the unit to be used as the setup/display unit or handle feed unit, the command unit or internal unit. The machining program variables (system variables for coordinate system) are changed simultaneously. 0: Internal unit 1: Unit specified by command Note 1: This parameter is valid only in initial millimeter

mode (0 is set in 14041 I_inch). The internal unit is always used in initial inch mode (1 is set in 14041 I_inch).

Note 2: This parameter is validated immediately after it is set.

Note 3: If addition setting is performed for tool and workpiece offset data with the command unit being inch and internal unit being mm, an error may be generated.

Note 4: If 1 is set for this parameter and two systems are used, the operation will follow the unit commanded for each system.

Note 5: The internal data is an internal unit determined with #1041 I_inch.

Note 6: This parameter is not related to the PLC axis. Related parameter: #1152 I_G20 (Initial command

unit)

0/1

aux10 (bit7)

Shorten JOG stop time

Specify whether to shorten the JOG stop time. 0: Do not shorten the JOG stop time. (Same as

before) 1: Shorten the JOG stop time.

0/1

1227 aux11 (bit0)

Select PLC signal or spindle feedrate attained

Set up this option when disabling the cutting start interlock by spindle feedrate attained.

0: Cutting start interlock by PLC signal 1: Cutting start interlock by spindle feedrate

attained

0/1

aux11 (bit1)

Select H or D code

Set up this option to validate the data that is set up on the tool life management screen when issuing the H99 or D99 command.

0: The H and D codes validate the data that is set up on the management setup screen.

1: Validates the data that is set up on the management setup screen when issuing the H99 or D99 command.

0/1

5. Base Specifications Parameters

II - 62

# Items Details Setting range (unit) aux11

(bit2) Measures against tool setter chattering

Select a condition where a relieving operation completes after measurement with tools.

0: Sensor signals has stopped for 500 ms or longer.

1: 100 s or longer has passed after sensor signals stopped.

0/1

aux11 (bit3)

Absolute coordinate switching (nose R) [Special display unit compatible]

Select whether to display a tool nose position or coordinate value with the absolute coordinate counter.

0: Displays the tool nose position. 1: Displays the position specified by program

command.

0/1

aux11 (bit4)

Program address check

Specify whether to simply check the program address when the machining program is executed.

0: Don't check the program address. 1: Check the program address.

0/1

aux11 (bit5)

Spindle rotation speed clamp

Specify whether to clamp the rotation in constant surface speed mode when the spindle rotation speed clamp command is issued.

0: Clamp the rotation regardless of the constant surface speed mode.

1: Clamp the rotation only in constant surface speed mode.

0/1

aux11 (bit6)

Word edit menu Select the word edit menu format. Set 0 in this parameter to select the following menu format:

LOOK UP DELETE REPLACE INSERT MENU

COPY PROGRAM MENU

SEARCH B.G. SRH B.G. END COMMENT RETURN

WORD WORD STR STR RETURN

Set 1 in this parameter to select the following men

COPY PROGRAM MENU

LOOK UP DELETE REPLACE INSERT MENU

SEARCH B.G. SRH B.G. END COMMENT RETURN

WORD WORD STR STR RETURN

0/1

5. Base Specifications Parameters

II - 63

# Items Details Setting range (unit) aux11

(bit7) Switch the range of tool life data to be input (For M system only)

set up the range of tool life data to be input or compared.

0: Inputs or compares all of the data output. 1: Inputs or compares part of the data output

1) Tool life management I data to be input or compared tool number (D), lifetime (E), life count (F), and auxiliary data (B).

2) Tool life management II data to be input or compared Group number (G), method (M), life (E/F), tool number (D), and compensation number (H)

Note: When the maintenance function data input/ output #(99) ( ) is set, all data will be input and compared.

0/1

1228 aux12 (bit0)

Switch coordinate value screen

Set up this option to switch the coordinate value screen.

0: 80-character screen 1: 40-character screen

0/1

aux12 (bit1)

Switch offset and parameter screen

Set up this option to switch the offset and parameter screen to the parameter screen.

0: Displays the offset and parameter screen. 1: Displays the parameter screen.

0/1

aux12 (bit2)

Switch data protection in data transmission mode

Set up the range of data protection in data transmission mode.

0: Protects both send and receive data. 1: Protects receive data only.

0/1

aux12 (bit3)

Nose R specification

Select whether to specify the nose R compensation by shape or wear number.

0: Specifies the nose R compensation by shape number.

1: Specifies the nose R compensation by wear number.

0/1

aux12 (bit4)

Select operation error or stop code

Specify both block cutting start interlock and cutting start interlock as the operation error or stop code.

0: Operation error 1: Stop code

0/1

aux12 (bit5)

Select constant surface speed coordinates

Select constant surface speed coordinates. 0: Workpiece coordinate value 1: Absolute coordinate value

0/1

aux12 (bit6)

Switch relative values displayed

Select whether to preset the relative coordinates with workpiece coordinate preset (G92.1) or counter preset (G92).

0: Preset relative coordinates. 1: Do not preset relative coordinates.

0/1

5. Base Specifications Parameters

II - 64

# Items Details Setting range (unit) aux12

(bit7) Protection with manual value command

Set up this option to protect a manual value command.

0: Does not protect the manual value command (same as before).

1: Protects the manual value command.

0/1

1229 set01 (bit0)

Subprogram interrupt

0: Specifies the user macro interrupt of macro type.

1: Specifies the user macro interrupt of sub-program type.

0/1

set01 (bit1)

Accurate thread cutting E

0: Address E specifies the number of threads per inch for inch screw cutting.

1: Address E specifies precise reading for inch screw cutting.

0/1

set01 (bit2)

Radius compen- sation type B (For M system only)

0: When the start-up and cancel commands are operated during radius compensation, their blocks are not handled by intersection operation processing; they are handled as offset vectors in the direction vertical to that of the commands.

1: When the start-up and cancel commands are operated during radius compensation, the intersection operation processing of the command block and the next block is executed.

0/1

set01 (bit2)

Nose R compen- sation type B (For L system only)

0: When the start-up and cancel commands are operated during nose R and radius compensation, their blocks are not handled by intersection operation processing; they are handled as offset vectors in the direction vertical to that of the commands.

1: When the start-up and cancel commands are operated during nose R and radius compensation, the intersection operation processing of the command block and the next block is executed.

0/1

set01 (bit3)

Initial constant surface speed

0: The initial state after power-ON is a constant surface speed control cancel mode.

1: The initial state after power-ON is a constant surface speed control mode.

0/1

set01 (bit4)

Synchronous tap

0: Handles the G74 and G84 tap cycles as the tap cycles with a floating tap chuck.

1: Handles the G74 and G84 tap cycles as the tap cycles without a floating tap chuck.

0/1

set01 (bit5)

Start point alarm Select an operation when the operation start point cannot be found while moving the next block of G117.

0: Enables an auxiliary function after the block has been moved.

1: Outputs an program error (P33) when the operation start point is not found.

0/1

5. Base Specifications Parameters

II - 65

# Items Details Setting range (unit) set01

(bit6) Grid display selection

Select a grid type to be displayed on the servo monitor screen during dog type reference point return.

0: Selects the distance between dog OFF and zero point (including a grid mask amount).

1: Selects a value given by reducing a grid mask amount from the distance between dog OFF and zero point.

0/1

1230 set02 (bit7)

Macro interface input/output for each system

0: The macro interface input/output are shared by the systems.

1: The macro interface input/output are used independently by the systems.

0/1

1231 set03 (bit1)

Switch graphic coordinates

Select whether to draw graphics with the machine coordinate value or the tool position coordinate value (position being machined, obtained by subtracting the tool compensation amount from machine coordinate values) when displaying the trace function.

0: Machine coordinate value (same as conventional method)

1: Tool position coordinate value The counter display and counter name are sequenced with this.

0/1

set03 (bit2)

Switch graphic check trace

Select whether to draw both the machine coordinate value (tool center path) and tool position coordinate value (program path) or draw only the coordinates selected with switch graphic coordinates (#1231 set03/ bit1) when using the program check function.

0: Both machine coordinates and tool position coordinates (same as conventional method)

1: Only coordinates designated with switch graphic coordinates.

0/1

set03 (bit3)

Hold display range information

Select whether to hold the display range information (drawing position and scale value) for graphic displays.

0: Hold. 1: Do not hold. (Initialize each time ... same as

conventional method)

0/1

set03 (bit4)

Switch zero point mark display position

Select the position for displaying the zero point mark in the graphic display.

0: Machine coordinate zero point (same as conventional method)

1: Workpiece coordinate zero point

0/1

5. Base Specifications Parameters

II - 66

# Items Details Setting range (unit)

set04 (bit0)

Switch load monitor

Select whether to detect the load with the load monitor's load detection, excluding during acceleration/ deceleration.

0: Detect also during acceleration/deceleration. (Conventional)

1: Do not detect during acceleration/deceleration.

0/1 1232

set04 (bit1)

Program format (IC card)

Select the format of the file output during copying (NC IC).

0: Add % to the head of the file. 1: The head of the file is No. 0.

0/1

1233 set05 (bit1)

Spindle clamp selection

Select whether to validate the spindle override for the spindle speed clamp command (G92 S?).

0: Spindle override invalid 1: Spindle override valid

0/1

1234 set06 (bit6)

Not used. 0/1

set06 (bit7)

Enable/disable MELDASNET

Enable or disable the MELDASNET function. 0: Enable 1: Disable

0/1

1235 set07 (bit0)

Helical interpolation speed 2

0: Select normal speed designation also for 3rd axis

1: Select arc plane element speed designation

0/1 (MAGIC64)

set07 (bit1)

File server selection for version upgrade

0: Set upper limit of program file size to 2 gigabytes.

1: Set upper limit of program file size to 16 megabytes.

0/1 (MAGIC64)

set07 (bit2)

Fixed type chopping compensa- tion valid only at start

When the fixed type compensation value is selected, the method is changed to the compensation value sequential update type after the first four cycles.

0: Method changeover invalid 1: Method changeover valid

0/1

1236 set08 (bit0)

Manual rotation axis feedrate unit

Select the unit of manual rotation axis feedrate. 0: Fixed to [/min] 1: Same speed as before

0/1

set08 (bit1)

Spindle speed detection

Select the pulse input source of actual spindle rotation speed output (R18/19) when spindle encoder serial connection (#3025 enc-on: 2) is selected.

0: Serial input 1: Encoder input connector

0/1

set08 (bit2)

Current limit droop cancel invalid

Set whether to cancel the position droop when the current limit changeover signal is canceled.

0: Cancel droop. 1: Do not cancel droop.

0/1

set08 (bit7)

Not used. 0/1

5. Base Specifications Parameters

II - 67

# Items Details Setting range (unit)

set09 (bit0)

External workpiece offset

Set up this function to use the external workpiece coordinates by shifting them to the Z axis.

0: Does not reverse the sign of external workpiece offsets (Z shift) (same as before).

1: Reverses the sign of external workpiece offsets (Z shift).

Note: When the sign of external workpiece offsets (Z shift) has been reversed, do not measure those external workpiece offsets. However, the external workpiece offsets can be measured by tool pre-setter.

0/1 1237 (PR)

set09 (bit1)

Switch PC I/F F modal

The feedrate display for the special display unit is changed.

0: Display as feed per minute. 1: Change between feed per minute and feed

per rotation according to the modal state.

0/1

set09 (bit2)

Switch PC I/F T modal

The T command display for the special display unit is changed. (Only L system)

0: Display tool No. (excluding low-order two digits).

1: Display including the compensation No.

0/1

set09 (bit3)

Switch PC I/F remaining distance dwell time display

The dwell time display for the special display unit is changed.

0: Display at feedrate display position. 1: Display at remaining distance display

position.

0/1

set09 (bit4)

Switch PC I/F execution program display/ comment display

The display of the program being executed for the special display unit is displayed.

0: Display as searched state, regardless of operation mode.

1: If operation mode and searched program differ, program is not displayed.

Comment is displayed for head block search.

0/1

set09 (bit5)

Switch PC I/F modal S

This parameter is for the special display unit I/F. 0: The S command commanded last is returned. 1: When #1039 spinno is 1

The 1st spindle data is returned. When #1039 spinno is 2

If #1199 Sselect for 2nd system is set to 1 with 2nd system setting, the 2nd spindle data is returned. When another command is issued, the 1st spindle data is returned.

Note: When using constant surface speed control (G96 modal), the actual rotation speed command is returned.

0/1

5. Base Specifications Parameters

II - 68

# Items Details Setting range (unit)

set10 (bit0)

Switch G36 function

If a G code system containing the G36 (automatic tool length measurement X) function is selected, select whether to use G36 for the automatic tool length measurement or arc thread cutting (CCW) function.

0: Automatic tool length measurement 1: Arc thread cutting (CCW)

0/1

set10 (bit6)

Not used. 0/1

1238 (PR)

set10 (bit7)

Switch operation alarm

Select whether to validate the NC alarm 5 (AL5) signal output.

0: NC alarm 5 (AL5) invalid All operation alarms are output to NC alarm 4

(AL4). All operation alarms are recorded in the

alarm history. 1: NC alarm 5 (AL5) valid The following operation alarms are not output

to NC alarm 4 (AL4). These are output to NC alarm 5 (AL5).

The operation alarms output to NC alarm 5 (AL5) are not recorded in the alarm history. External interlock axis found Cutting override zero External feedrate zero Block start interlock Cutting block start interlock Cutting interlock for spindle-spindle

polygon (G51.2)

0/1 (Default: 0)

1239 (PR)

set11 (bit0)

Coil switching method

0: Via PLC. (Y2D7) 1: NC internal processing. (Y2D7 is invalid.)

0/1

set11 (bit1)

Not used. 0/1

set11 (bit2)

Not used. 0/1

set11 (bit3)

Polygon machining mode at reset

Select whether to cancel the polygon machining mode when reset is applied.

0: Do not cancel. 1: Cancel.

0/1

set11 (bit4)

Invalidate G51.1 phase command

Select whether to carry out phase control with the spindle-spindle polygon function.

0: Always validate phase control. * When R is not commanded, it is handled as

R0. 1: Validate phase control only at R command

0/1

5. Base Specifications Parameters

II - 69

# Items Details Setting range (unit)

set11 (bit5)

Door interlock spindle speed clamp valid

Select whether to validate the spindle clamp speed changeover function by the PLC signal.

0: Invalid 1: Valid

0/1

set11 (bit6)

External deceleration axis compliance valid

Designate the method for setting the external deceleration speed.

0: Set speed common for all axes (#1216 extdcc external deceleration speed)

1: Set speed for each axis (#2086 exdcax external deceleration speed)

0/1

set11 (bit7)

APLC software working environment setting

0: Run the APLC software with the ROM. 1: Run the APLC software with the RAM.

0/1

1240 (PR)

set12 (bit0)

Handle input pulse

Select the handle input pulse. 0: MELDAS standard handle pulse 1: Handle 400 pulse

0/1

set12 (bit1)

Megatorque motor handle feed magnification

Select the magnification of megatorque motor handle 1 pulse.

0: Double the handle 1 pulse magnification specified by the handle feed magnification signal (Y2C0 to Y2C2).

1: Use the handle 1 pulse magnification specified by the handle feed magnification signal (Y2C0 to Y2C2) as is.

0/1

set12 (bit2)

Zero point shift amount magnification

If "1" is set, the following magnification will be applied on the #2027 G28sft reference point shift amount, #2057 zero point proximity + and #2058 zero point proximity settings.

For 0.1m : 10-fold For 0.01m : 100-fold

0/1

5. Base Specifications Parameters

II - 70

(SETUP PARAM 1. 9/15)

# Items Details Setting range (unit) 1265 (PR)

ext01 (bit0)

Command format 1

Select the command format for the fixed cycle for compound lathe.

0: Conventional format 1: MELDAS special format

(1 block command method)

0/1

ext01 (bit1)

Command format 2

Select the command format for the lathe fixed cycle. 0: Conventional format 1: MELDAS special format

0/1

ext01 (bit2)

Command format 3

Select the command format for the hole drilling fixed cycle.

0: Conventional format 1: MELDAS special format

0/1

1266 (PR)

ext02 Not used.

1267 (PR)

ext03 (bit0)

G code type Select the high-speed high-accuracy G code type. 0: Conventional format 1: F format

0/1

1268 (PR)

ext04 Not used.

1269 (PR)

ext05 Not used.

1270 (PR)

ext06 (bit7)

Handle C axis coordinate during cylindrical interpolation

Specify whether the rotary axis coordinate before the cylindrical interpolation start command is issued is kept during the cylindrical interpolation or not.

0: Do not keep 1: keep

0/1

1271 (PR)

ext07 (bit0)

Mirror image operation

Select the type of mirror image operation. (Applicable only to M65 and M66)

0: Type 1 - The program mirror image, external mirror

image, and parameter mirror image are exclusive to each other.

- An increment command moves the image to the position indicated by the move amount with the sign inverted.

1: Type 2 - Mirror image operation is enabled when the

program mirror image (G51.1) command is issued or when the external signal or parameter is ON.

- An increment command moves the image to the position determined by applying the mirror image to the absolute program coordinates.

0/1 (Default: 0)

5. Base Specifications Parameters

II - 71

# Items Details Setting range (unit) ext07

(bit1) Address specifying fixed cycle repetition count (For M system only)

Specify the address that specifies the fixed cycle repetition count. (Applicable only to M65 and M66)

0: Address L only 1: Addresses K and L

If addresses K and L are specified simultaneously, the data at address K is used for operation.

0/1 (Default: 0)

ext07 (bit2)

F-command unit Specify the unit to be used if a thread cutting read command contains on decimal point. (Applicable only to M65 and M66)

0: Type 1 (conventional specifications) F1 1 mm/rev, 1 inch/rev 1: Type 2 F1 0.01 mm/rev, 0.0001 inch/rev

0/1 (Default: 0)

ext07 (bit3)

G-code group for unidirectional positioning (for M system only)

Specify the G-code group for unidirectional positioning. (Applicable only to M65 and M66)

0: Unmodal G code (group 00) 1: Modal G code (group 01)

Related parameter: #8209 G60 SHIFT (Set the last positioning direction and distance for each axis applicable when the unidirectional positioning command is issued.)

0/1

ext07 (bit4)

Operation by independent G40 command

Specify the mode of canceling radius compensation vector by the independent G40 command. (Applicable only to M65 and M66) (Default: 0)

0: Type 1 (conventional specifications) The independent G40 command cancels the radius compensation vector.

1: Type 2 The radius compensation vector is not canceled by the independent G40 command but is canceled by the next move command for the radius compensation plane.

0/1 (Default: 0)

ext07 (bit5)

Cut start position (For L system only)

Specify the position from where cutting begins in a fixed cycle for compound lathe.

0: Conventional specifications The cut start position is determined by the final shaping program.

1: Extended specifications The cut start position is determined from the cycle start point.

0/1 (Default: 0)

5. Base Specifications Parameters

II - 72

# Items Details Setting range (unit) ext07

(bit6) Nose R compensation (For L system only)

Specify whether to apply nose R compensation to shapes in a rough cutting cycle.

0: Conventional specifications If nose R compensation is enabled for the final shaping program, the shape obtained after applying nose R compensation to the final shaping program is used as the rough cutting shape.

1: Extended specifications The shape made by the final shaping program, without nose R compensation, is used as the rough cutting shape.

0/1 (Default: 0)

ext07 (bit7)

Cut amount (For L system only)

Specify the operation to be performed when the program-specified cut amount exceeds the cut amount of the final shaping program.

0: Conventional specifications A program error occurs if the program-specified cut amount exceeds the cut amount of the final shaping program.

1: Extended specifications Rough cutting is performed by one cut if the program-specified cut amount exceeds the cut amount of the final shaping program.

0/1 (Default: 0)

1272 (PR)

ext08 (bit0)

Switch pocket machining operation

0: Conventional specifications Pocket machining is selected with the H

designation. The pull direction when pocket machining is

ON is the Z direction. 1: Extended specifications If there is an X and Z axis in the first

movement block after the finished shape start block is started, pocket machining will start.

The pull direction when pocket machining is ON is the X direction.

0/1

ext08 (bit1)

M function synchronous tap cycle

Specify whether to enable the M function synchronous tap cycle.

0: Invalid 1: Valid

ext08 (bit2)

Spiral/conical interpolation command format 2

Select the command format for spiral interpolation and conical interpolation.

0: Type 1 (conventional specifications) 1: Type 2 (spiral speed L designation, increment

designation)

0/1

ext08 (bit3)

Switch macro call function

Select whether to shift the argument to the subprogram if nests are overlapped when per block call (G66.1) is commanded.

0: Shift argument even if nests are overlapped. 1: Do not shift arguments if nests differ.

(Conventional specifications)

0/1

5. Base Specifications Parameters

II - 73

# Items Details Setting range (unit) ext08

(bit4) Tap cycle selection

Select the tap cycle. 0: Pecking tap cycle 1: Deep hole tap cycle

0/1

ext08 (bit5)

Deep hole tap cycle override selection

Select whether to validate override on the pulling operation during synchronized tapping with the deep hole tap cycle.

0: Invalid 1: Valid

0/1

ext08 (bit6)

Switch corner chamfering/ corner R command format

The corner chamfering/corner R command format is extended.

0: Command format I (conventional format) Issue a command with comma (,C and ,R). 1: Command format II In addition to command format I, commands

can be issued with an address that does not have a comma.

Corner chamfering: I/K or C, corner R: R

0/1

ext08 (bit7)

Return position after macro interrupt in fixed cycle selection

Select the destination to return to after a macro interrupt in the fixed cycle.

0: Return to block in fixed cycle. 1: Return to block after fixed cycle.

0/1

1273 (PR)

ext09 (bit0)

Switch ASIN calculation results range

Select the ASIN calculation results range. 0: 90 to 90 1: 90 to 270

0/1

ext09 (bit1)

Switch system variable unit

Select the unit for the system variable #3002 (time during automatic start).

0: 1ms unit 1: 1 hour unit

0/1

ext09 (bit2)

Switch G71, G72, G73 cutting direction judgment

Select whether to determine the cutting direction with the finished shape, or according to the commanded finishing allowance and cutting allowance when the longitudinal rough cutting cycle (G71), face rough cutting cycle (G72) or closed loop cutting cycle (G73) is commanded.

0: Conventional specifications Determined according to the finished shape

program. 1: Extended specifications Determined according to the finishing

allowance and cutting allowance commanded in the program.

0/1

ext09 (bit3)

Facing turret mirror image coordinate value type

Select the coordinate values of the axis for which facing turret mirror image is valid.

0: Move axis in same direction as machine value.

1: Move axis in direction opposite machine value.

0/1

ext09 (bit4)

Facing turret mirror image valid axis selection

Select the axis for which facing turret mirror image is valid.

0: Fixed to 1st axis. 1: Determined according to plane selected

when facing turret mirror image is commanded.

0/1

5. Base Specifications Parameters

II - 74

# Items Details Setting range (unit)

1274 (PR)

ext10 (bit7)

Word range check

Select whether to check that the operation expression of the word date in the program is enclosed in brackets ( [ ] ) when the machine program is executed. This check is also applied to the 08000 to 09999 and the machine manufacture macro program.

0: Check valid 1: Check invalid

0/1

1275 (PR)

ext11 Not used.

1276 (PR)

ext12 Not used.

1277 (PR)

ext13 (bit0)

Tool life management II count type 2

Specify how and when the mount or use count is incremented in tool life management II.

0: Type 1 The count is incremented when the spindle is used for cutting.

1: Type 2 The count is incremented for the tool used or mounted for one program. The increment is enabled by resetting.

0/1 (Default: 0)

1278 (PR)

ext14 (bit0)

Program restart method selection

Select the program restart method. 0: Type A 1: Type B

0/1

ext15 (bit0)

System synchroniza- tion method

Select the system synchronization method. 0: If one system is not in automatic operation,

ignore the synchronization command and execute the next block.

1: Operate according to the synchronization ignore signal.

If the synchronization ignore signal is set to "1", the synchronization command will be ignored. When set to "0", synchronization will be applied.

0/1

ext15 (bit1)

Interrupt amount during machine lock

Select the manner to handle the interruption amount during machine lock.

0: Cancel when reset. 1: Do not cancel when reset. Instead cancel

during manual zero point return.

0/1

1279 (PR)

ext15 (bit2)

Selection of cutting start interlock target block

Select whether the cutting start interlock is valid for successive cutting blocks.

0: Valid for successive cutting blocks. 1: Invalid for successive cutting blocks.

0/1

5. Base Specifications Parameters

II - 75

# Items Details Setting range (unit)

1280 (PR)

ext16 (bit0)

I/F per axis during cross machining control

Set the handling of the following PLC I/F for axes interchanged with cross machining control. Mirror image Manual/automatic interlock Manual/automatic machine lock

0: Follows axis configuration before cross machining control.

1: Follows axis configuration after cross machining control.

(Example) Set as follows for the automatic interlock (+) device for X1 when carrying out cross machining with the 1st axis (X1) in the 1st system and 1st axis (X2) in the 2nd system. Setting value 0: Y1A8 (I/F for 1st axis in

1st system) Setting value 1: W28 (I/F for 1st axis in

2nd system) Note: If the number of axes in the system changes

with cross machining, the I/F of the target axis may change when this parameter is set to "1".

(Example) When 1st system's C axis is moved to 2nd system with a 1st system (X, Z, C, Y) and 2nd system (X, Z) configuration:

When setting value is 1: W2A, W12 and W4A, etc., will be the

I/F for the C axis moved to the 2nd system. However, Y192, Y1AA and Y1CA, etc., will change to the I/F of the Y axis in the 1st system because the axes following the removed C axis (third place) are shifted up.

0/1

5. Base Specifications Parameters

II - 76

# Items Details Setting range (unit)

1280 (PR)

ext16 (bit1)

Cross machining control cancel with reset

Select whether to cancel the cross machining control when reset is applied.

0: Cancel cross machining control with reset. 1: Do not cancel cross machining control with

reset

0/1

ext16 (bit2)

Interchange coordinate value display

Set whether to interchange (or move) the coordinate values when displaying. This setting will be followed when the axes are interchanged and when the axes are moved.

0: Interchange (or move) coordinate values with cross machining control, and display.

1: Display coordinate values for cross machining control without interchanging (or moving).

(Example) When 1st system's C axis is moved to 2nd system with a 1st system (X, Z, C, Y) and 2nd system (X, Z) configuration: 1st system: X, Z and Y coordinate

values are displayed. 2nd system: X, Z and C coordinate

values are displayed.

0/1

ext16 (bit3)

Reset operation for synchroniza- tion/super- imposition control

Select whether to cancel synchronization/ superimposition control with resetting.

0: Cancel. 1: Do not cancel.

0/1

5. Base Specifications Parameters

II - 77

# Items Details Setting range (unit)

1281 (PR)

ext17 (bit0)

Zero point return operation changeover parameter

(Zero point setting operation) The "Operation error 1036" will occur regardless of this parameter, and regardless of manual or automatic operation. (High-speed zero point return)

0: The master axis and slave axis will

simultaneously start zero point return. Even if one of the axes reaches the zero point, the other axis will continue to move until it reaches the zero point. Thus, if the difference of the master axis and slave axis feedback position before zero point return is larger than the tolerable synchronization error amount, the error "Operation error 0051" will occur during zero point return.

The master axis and slave axis will

simultaneously start zero point return. When the master axis reaches the zero point, the slave axis will stop. Thus, the positional relation of the master axis and slave axis established before zero point return is maintained.

1:

The master axis and slave axis will simultaneously start zero point return. When the master axis reaches the zero point, the slave axis will stop. Thus, the positional relation of the master axis and slave axis established before zero point return is maintained.

0/1

ext17 (bit1)

Tool offset addition axis selection

0: Follows Tchg34 1: Plane selection Base J setting name is set as

the 3rd axis compensation axis.

0/1

1282 (PR)

ext18 Not used.

1283 (PR)

ext19 Not used.

1284 (PR)

ext20 (bit0)

Spindle speed clamp check

Select whether to check the spindle speed clamp under the constant surface speed control.

0: Check the spindle speed clamp. 1: Not check the spindle speed clamp.

(Note) This parameter is enabled when the parameter "#1146 Sclamp" is set to "1". (Applicable only to M65 V series and M64 C version series)

0/1

5. Base Specifications Parameters

II - 78

# Items Details Setting range (unit)

1285 (PR)

ext21 (bit0)

Multi-system program generation and operation

0: When a machining program is newly registered, it is registered as a program for the selected system.

1: When a program is newly registered, a system common program No. is generated unconditionally. If there are no contents in the subprogram when a subprogram is called during automatic operation, the program will be searched for and executed from $1.

0/1

ext21 (bit1)

Changeover of method to select operation program

0: Select the program in the selected system with operation search.

1: Select a common system program with operation search. (A common system program No. will be selected.)

0/1

1286 (PR)

ext22 (bit0)

Program input/output method selection

0: Only the programs in the selected system are input/output.

1: The designated programs are output for all systems. The systems are delimited with the "$" mark. The programs delimited with the $ mark are assigned and input into each system. (If the program does not have a $ mark, it will be handled as system 1.)

0/1

ext22 (bit1)

Not used.

ext22 (bit2)

0 No. for program input No.

Select the action to be taken when the same program No. is input during data input.

0: The 0 No. when the same 0 No. is input successively is handled as a character string data.

1: The 0 No. is handled as a program No. when the same 0 No. is input successively. Whether to overwrite the program or cause an error is set with #1218 bit 7 "Input by program overwrite".

0/1

ext22 (bit3)

No 0 No. at machining program input

This setting enables the machining program input even if there is no program No. (0 No.). The program No. is fixed to 01 in this case.

0: Input disabled 1: Input enabled

0/1

1287 (PR)

ext23 (bit0)

Workpiece coordinate display

Select the mode of displaying the workpiece coordinate counter.

0: Dont update the display immediately after workpiece coordinate data is changed.

1: Update the display immediately after workpiece coordinate data is changed.

0/1

5. Base Specifications Parameters

II - 79

# Items Details Setting range (unit)

ext23 (bit3)

Counter display expanded function selection

0: Display the command value that does not consider the tool length offset amount or workpiece coordinate offset amount.

1: The counter display expanded function is validated. (bit4 to bit7)

0/1

ext23 (bit4)

Relative coordinate display

(M system) 0: Display the actual position including tool

length offset. 1: Display the machining position in terms of a

program command excluding tool length offset.

(L system) 0: Display the actual position including tool

shape compensation. 1: Display the machining position in terms of a

program command excluding tool shape compensation.

0/1

ext23 (bit5)

Relative coordinate display

(M system) 0: Display the actual position including tool

radius compensation. 1: Display the machining position in terms of a

program command excluding tool radius compensation.

(L system) 0: Display the actual position including nose R

compensation. 1: Display the machining position in terms of a

program command excluding nose R compensation.

0/1

ext23 (bit6)

Absolute coordinate display [Special display unit compatible]

(M system) 0: Display the actual position including tool

length offset. 1: Display the machining position in terms of a

program command excluding tool length offset.

(L system) 0: Display the actual position including tool

shape compensation. 1: Display the machining position in terms of a

program command excluding tool shape compensation.

0/1

5. Base Specifications Parameters

II - 80

# Items Details Setting range (unit) ext23

(bit7) Absolute coordinate display [Special display unit compatible]

(M system) 0: Display the actual position including tool

radius compensation. 1: Display the machining position in terms of a

program command excluding tool radius compensation.

(L system) 0: Display the actual position including nose R

compensation. 1: Display the machining position in terms of a

program command excluding nose R compensation.

With the L system, the effect onto the nose R compensation's absolute coordinate counter is also affected by the L system coordinate changeover parameter (#1227 aux11/bit 3 absolute coordinate changeover (nose R)). In actual use, if this parameter is set to 1, or if #1227 aux 11/bit 3 is set to 1, the position in the program commands will be displayed with the absolute coordinate counter.

0/1

1288 (PR)

ext24 (bit0)

MDI program clear

Select whether to initialize the MDI buffer when MDI operation ends, the power is turned ON again, reset is input, or emergency stop is canceled.

0: Do not clear programs registered with MDI. 1: Clear programs registered with MDI, and

save only % programs.

0/1

1289 (PR)

ext25 Not used.

1290 (PR)

ext26 Not used.

1291 (PR)

ext27 Not used.

1292 (PR)

ext28 Not used.

1293 (PR)

ext29 Not used.

1294 (PR)

ext30 Not used.

1295 (PR)

ext31 Not used.

1296 (PR)

ext32 Not used.

1297 (PR)

ext33 Not used.

1298 (PR)

ext34 Not used.

5. Base Specifications Parameters

II - 81

# Items Details Setting range (unit)

1299 (PR)

ext35 Not used.

1300 (PR)

ext36 (bit0)

Multiple spindle control II

Select multiple spindle control I or II. 0: Multiple spindle control I 1: Multiple spindle control II (select from ladder)

0/1

ext36 (bit7)

Spindle synchroniza- tion command method

Select the spindle synchronization command method.

0: Spindle synchronization with PLC I/F 1: Spindle synchronization with G command

0/1

5. Base Specifications Parameters

II - 82

(SETUP PARAM 1. 10/15)

# Items Details Setting range (unit) 1301 nrfchk Origin

neighboring check method

Select the high-speed check method of the origin neighboring signal.

0: Do not check positions near the origin at high speeds. (Conventional specifications)

1: Check positions near the origin at high speeds using command machine positions.

2: Check positions near the origin at high speeds using detector feedback positions.

0 to 2

1302 AutoRP Automatic return by program restart

0: Return the system to the restart position manually and then restart the program.

1: For program restarting, the first activation automatically moves the system to the restart position.

0/1

1303 (PR)

V1comN No. of #100 address system common variables

Set the number of common variables common for the system starting from address #100.

0 to 100

1304 (PR)

V0comN No. of #500 address system common variables

Set the number of common variables common for the system starting from address #500.

0 to 500

1305 corjug Corner deceleration tangent judgment

Select whether to judge corner deceleration with a polygon shape or tangent during helical interpolation and spiral interpolation.

0: Polygon judgment Helical interpolation is interpreted as

polygonal, and the corner deceleration is judged with the approximate vector.

1: Tangent judgment The vector is calculated from the center of

the helical interpolation, the start point and the end point, and corner deceleration is judged.

0/1

1306 InpsTyp Deceleration check specification type

Select the parameter specification type for the G0 or G1 deceleration check.

0: Deceleration check specification type 1 G0 is specified with "#1193 inpos", and G1+G9 with "#1223 aux07/BIT1".

1: Deceleration check specification type 2 G0 or G1+G9 is specified with "#1193 inpos".

0/1

1310 WtMmin Minimum value for synchroniza- tion M code

Set the minimum value for the M code. When "0" is set, the synchronization M code will be invalid.

0, 100 to 99999999

5. Base Specifications Parameters

II - 83

# Items Details Setting range (unit)

1311 WtMmax Maximum value for synchroniza- tion M code

Set the maximum value for the M code. When "0" is set, the synchronization M code will be invalid.

0, 100 to 99999999

1312 T_base Tool life management standard number

When the T code command is issued while specifying a value that exceeds the value set in this parameter, the value obtained by subtracting the set value from the command value is used as the tool group number for tool life management. The value specified by the T code command is equal to or less than the value set in this parameter, the T code is handled as a normal T code and not subjected to tool life management. When 0 is set in this parameter, the T code command always specifies a group number. (This parameter is valid for M-system tool life management II.)

0 to 9999

1313 TapDw1 Synchronous tap hole bottom wait time

Specify the hole bottom wait time for synchronous tapping. When the P address is specified, the greater value is used as the hole bottom wait time. When an in-position check is performed at the hole bottom, dwelling for the specified time is completed after the in-position check is complete. (Applicable only to the M64 D version series) Note: This parameter is valid only when 1 is set in

#1223 aux07 bit 3 (synchronous tap in-position check improvement).

0 to 999 (ms)

1314 TapInp Synchronous tap in-position check width (tap axis)

Specify the hole bottom in-position check width for synchronous tapping. (Applicable only to the M64 D version series) Note: This parameter is valid only when 1 is set in

#1223 aux07 bit 3 (synchronous tap in-position check improvement).

1 to 32767 (1m steps)

1324 Chop_R Chopping compensa- tion value fixing method

Head number of the R register used as the compensation amount save area during fixed compensation amount method.

1900 to 2782

5. Base Specifications Parameters

II - 84

(SETUP PARAM 1. 11/15)

# Items Details Setting range (unit) 1501 polyax

(For L system only)

Rotational tool axis number

Specify the number of the rotational tool axis (servo axis) used for polygon machining (G51.2). Set 0 when not using polygon machining (spindle-servo axis), or when using spindle-spindle polygon machining. A value exceeding the base specification parameter #1002 axisno cannot be specified. This parameter is valid when the G code system is 6 or 7 (7 or 8 is set in base specification parameter #1037 cmdtyp).

0 to controlled axis number

1502 G0Ipfg G1 G0 deceleration check

0: Do not perform a deceleration check when the move direction is changed from G1 to G0.

1: Perform a deceleration check when the move direction is changed from G1 to G0. (Applicable only to the M64 D version series)

0/1

1503 G1Ipfg G1 G1 deceleration check

0: Do not perform a deceleration check when the move direction is changed from G1 to G1.

1: Perform a deceleration check when the move direction is changed from G1 to G1. (Applicable only to the M64 D version series)

0/1

1505 ckref2 Second origin return check

Specify the trigger for a check at the specified position in manual second original return mode.

0: Completion of spindle orientation 1: Generation of second origin return interlock

signal

0/1

1506 F1_FM Upper limit of F1 digit feedrate

Specify the maximum value up to which the F1 digit feedrate can be changed. (Applicable only to M65 and M66)

0 to 60000 (mm/min)

1507 F1_K F1 digit feedrate change constant

Specify the constant that determines the speed change rate per manual handle graduation in F1 digit feedrate change mode. (Applicable only to M65 and M66)

0 to 32767

1510 DOOR_H Shorten door interlock II axis stop time

Specify whether to shorten the time during which the axis is stopped when the door is opened.

0: Use the conventional axis stop time. 1: Shorten the axis stop time.

Note: When the door interlock II signal is input via a ladder, the conventional axis stop time is used.

0/1

1511 DOORPm Signal input device 1 for door interlock II: for each system

Specify the fixed device number (X??) for door interlock II signal input for each system. A device number from X01 to XFF can be specified. Device number 000 is invalid. Specify device number 100 when using no fixed device number for door interlock II signal input. Related parameter: #1154 pdoor (Door interlock II for

each system)

000 to 100 (hexadecimal)

5. Base Specifications Parameters

II - 85

# Items Details Setting range (unit)

1512 DOORPs Signal input device 2 for door interlock II: for each system

Specify the fixed device number (X??) for door interlock II signal input for each system. (Specify the same value as that of #1155.) Related parameter: #1154 pdoor (Door interlock II for

each system)

000 to 100 (hexadecimal)

1513 stapM M code for synchronous tap selection

Select the synchronous tap mode using the miscellaneous function code of the value set in this parameter. The M function command can be issued immediately before the tap command or in the same block. This function is valid only when 1 is set in #1272 ext08/bit 1 (Enable/disable M-function synchronous tap cycle). Note: Do not use M00, 01 02, 30, 98, and 99.

0 to 99999999

1514 expLinax Exponential function interpolation linear axis

Set the axis address name for the linear axis used in exponential function interpolation.

A to Z

1515 expRotax Exponential function interpolation rotary axis

Set the axis address name for the rotary axis used in exponential function interpolation.

A to Z

1516 mill_ax Milling axis name

Set the name of the rotary axis used in milling interpolation. Only one rotary axis can be set. When there is no E command in issuing the G12.1 command, this parameter will be followed.

A to Z

1517 mill_C Milling interpolation hypothetical axis name

Select the hypothetical axis command name for milling interpolation. When there is no D command in issuing the G12.1 command, this parameter will be followed.

0: Y axis command 1: Command rotary axis name.

0/1

1518 polm Spindle- spindle polygon Workpiece spindle No.

Set the number of the workpiece spindle used in spindle-spindle polygon machining. Note: The 1st spindle will be selected when 0 is set.

0 to number of spindles

1519 pols Spindle- spindle polygon Tool spindle No.

Set the number of the tool spindle used in spindle- spindle polygon machining. Note: The 2nd spindle will be selected when 0 is set.

0 to number of spindles

1520 (PR)

Tchg34 Additional axis tool compensa- tion operation

Select whether to carry out the additional axis' tool compensation function with the 3rd axis or 4th axis.

0: Select 3rd axis. 1: Select 4th axis.

0/1

1521 C_min Minimum turning angle

Set the minimum turning angle of the normal line control axis at the block joint during normal line control.

0.000 to 360.000 ()

5. Base Specifications Parameters

II - 86

# Items Details Setting range (unit)

1522 (PR)

C_axis Normal line control axis

Set the number of the axis for normal line control. Designate a rotary axis.

0: Normal line control disabled

1 to 6: Axis No. (number of control axes)

1523 C_feed Normal line control axis turning speed

This is valid with normal line control type I. Designate the turning speed of the normal line control axis at the block joint during normal line control. Set a value that does not exceed the normal line control axis' clamp speed (#2002 clamp).

0 to 1000000 (/min)

1524 C_type Normal line control type

Set the normal line control type. 0: Normal line control type I

1: Normal line control type II

1525 laxlen L axis length Special function 1526 raxlen R axis length Special function 1527 flclen Distance

between support points

Special function

1528 rflch R point support point height

Special function

1529 laxcmp L axis compensa- tion amount

Special function

1530 raxcmp R axis compensa- tion amount

Special function

1531 flccmp Distance between support point compensa- tion amount

Special function

1532 G01rsm G00 L/R interpolation simultaneous reach

Special function

1533 millPax Pole coordinate linear axis name

Set the linear axis used for pole coordinate interpolation.

Control axis address such as X, Y or Z

5. Base Specifications Parameters

II - 87

# Items Details Setting range (unit)

1534 SnG44.1 Spindle No. for G44.1 command

Set the selected spindle No. for the G44.1 command.

0: 2nd spindle 1: 1st spindle 2: 2nd spindle 3: 3rd spindle 4: 4th spindle If a spindle that does not exist is set, the 2nd spindle will be used. Note that if there is only one spindle, the 1st spindle will be used.

1535 C_leng Minimum turning movement amount

Set the minimum turning movement amount of the normal line control axis at the block joint during normal line control.

0.000 to 99999.999 (mm)

1537 to

1544

crsax[1] to crsax[8]

Cross machining control axis

Set the axis to be interchanged during cross machining control. Using two digits, set the name of the axis interchanged with that where the cross machining control request signal is input, or that moves to the position where the signal is input.

Two digits between A to Z and 1 to 9 (Setting is cleared when 0 is set)

(SETUP PARAM 1. 12/15) # Items Details Setting range (unit)

1549 Iv0vr1 Override 1 start curvature radius

Set the override 1 start curvature radius for executing involute interpolation with the high-speed high-accuracy II mode.

0.001 to 99999.999 (mm)

1550 Iv0vr2 Override 2 start curvature radius

Set the override 2 start curvature radius for executing involute interpolation with the high-speed high-accuracy II mode.

0.001 to 99999.999 (mm)

1551 Iv0vr3 Override 3 start curvature radius

Set the override 3 start curvature radius for executing involute interpolation with the high-speed high-accuracy II mode.

0.001 to 99999.999 (mm)

1552 Iv0vr4 Override 4 start curvature radius

Set the override 4 start curvature radius for executing involute interpolation with the high-speed high-accuracy II mode.

0.001 to 99999.999 (mm)

1553 Iv0vr5 Override 5 start curvature radius

Set the override 5 start curvature radius for executing involute interpolation with the high-speed high-accuracy II mode.

0.001 to 99999.999 (mm)

1554 Iv0rd2 Involute interpolation override 2

Set the override value at the curvature radius Iv0vR2 for executing involute interpolation with the high-speed high-accuracy II mode. Note: If the override value is not set (setting value:

0), the setting will be invalid, and the override will be 100%.

1 to 100 (%)

#1199 #1534 Selected spindle 0:G43.1 Not used. 1st spindle 1:G44.1 0 2nd spindle

1 1st spindle 2 2nd spindle 3 3rd spindle 4 4th spindle

2:G47.1 Not used. All spindles

5. Base Specifications Parameters

II - 88

# Items Details Setting range (unit)

1555 Iv0rd3 Involute interpolation override 3

Set the override value at the curvature radius Iv0vR3 for executing involute interpolation with the high-speed high-accuracy II mode. Note: If the override value is not set (setting value:

0), the setting will be invalid, and the override will be 100%.

1 to 100 (%)

1556 Iv0rd4 Involute interpolation override 4

Set the override value at the curvature radius Iv0vR4 for executing involute interpolation with the high-speed high-accuracy II mode. Note: If the override value is not set (setting value:

0), the setting will be invalid, and the override will be 100%.

1 to 100 (%)

1557 Iv0rd5 Involute interpolation override 5

Set the override value at the curvature radius Iv0vR5 for executing involute interpolation with the high-speed high-accuracy II mode. Note: If the override value is not set (setting value:

0), the setting will be invalid, and the override will be 100%.

1 to 100 (%)

1558 Iv0Min Involute interpolation override lower limit value

Set the lower limit value of the involute interpolation override. Note: If the override value is not set (setting value:

0), the setting will be invalid, and the override will be 100%.

1 to 100 (%)

1559 IvAMax Involute interpolation maximum acceleration rate

Set the maximum acceleration rate of the constant acceleration control for executing involute interpolation with the high-speed high-accuracy II mode. Note: If this parameter is not set (setting value: 0),

the setting will be invalid, and the normal acceleration rate (#1207 G1btL) will be applied.

1 to 32767 (ms)

1560 IvFMin Involute interpolation minimum feedrate

Set the minimum feedrate of the constant acceleration control for executing involute interpolation with the high-speed high-accuracy II mode. (Valid when executing compensation with the accuracy coefficient.) Note: If this parameter is not set (setting value: 0),

the feedrate will not be clamped.

1 to 32767 (ms)

1571 SSSdis SSS control adjustment coefficient fixed value selection

The shape recognition range for SSS control is fixed.

0/1

5. Base Specifications Parameters

II - 89

# Items Details Setting range (unit)

1572 Cirorp Arc command overlap

Fluctuation of the speed at the arc and linear or arc and arc joints will be eliminated during the high-speed high-accuracy II mode.

0: Do not overlap arc command blocks. 1: Overlap arc command blocks. (Eliminate the

speed fluctuation) Note: This parameter is invalid during SSS control.

0/1

(SETUP PARAM 1. 13/15) # Items Details Setting range (unit)

1801 Hacc_c Arc radius clam acceleration -99999999 to +99999999

1802 Macc_c Acceleration check at middle speed -99999999 to +99999999

1803 Lacc_c Acceleration check at low speed -99999999 to +99999999

1811 Hcof_A X-axis high acceleration coefficient -99999999 to +99999999

1812 Hcof_B X-axis high acceleration coefficient -99999999 to +99999999

1813 Mcof_A X-axis middle acceleration coefficient -99999999 to +99999999

1814 Mcof_B X-axis middle acceleration coefficient -99999999 to +99999999

1815 Lcof_A X-axis low acceleration coefficient -99999999 to +99999999

1816 Lcof_B X-axis low acceleration coefficient -99999999 to +99999999

1817 mag_C X-axis change magnification [%] Set 0 when no compensation or change is executed.

-99999999 to +99999999

1821 Hcof_A Y-axis high acceleration coefficient -99999999 to +99999999

1822 Hcof_B Y-axis high acceleration coefficient -99999999 to +99999999

1823 Mcof_A Y-axis middle acceleration coefficient -99999999 to +99999999

1824 Mcof_B Y-axis middle acceleration coefficient -99999999 to +99999999

1825 Lcof_A Y-axis low acceleration coefficient -99999999 to +99999999

1826 Lcof_B Y-axis low acceleration coefficient -99999999 to +99999999

1827 mag_C Y-axis change magnification [%] Set 0 when no compensation or change is executed.

-99999999 to +99999999

5. Base Specifications Parameters

II - 90

(SETUP PARAM 1. 14/15)

# Items Details Setting range (unit) 1901 (PR)

station addr Set up a station address number (the NC is the n-th slave station).

1 to 7

1902 (PR)

Din size Set up the size of the data to be transferred from the PC to the NC (from the master station to the slave station) in bytes (8 points).

0 to 32 (bytes (8 bits))

1903 (PR)

Dout size Set up the size of the data to be transferred from the NC to the PC (from the slave station to the master station) in bytes (8 points).

0 to 32 (bytes (8 bits))

1904 (PR)

data length Set up the data length of a character. 0 to 2 : 7 bits 3 : 8 bits

1905 (PR)

baud rate Set up a data transfer rate. The transfer rate differs according to operation clock rates

Clock: 6 MHz/ 10 MHz

0: 38400 / 57600 1: 19200 / 28800 2: 9600 / 14400 3: 4800 / 7200 4: 2400 / 3600 5: 1200 / 1800 6: 600 / 900 (bps)

1906 (PR)

stop bit Set up the stop bit length. 0 and 1: 1 bit 2 and 3: 2 bits

1907 (PR)

parity check Select whether to make a parity check. 0: Invalid 1: Valid

1908 (PR)

even parity Select the odd or even parity bit. If no parity check is specified, this parameter is ignored.

0: Odd parity 1: Even parity

1909 (PR)

Tout (ini) (ini) specifies a time-out from when the connection check sequence finishes to when the first usual sequence (input) finishes.

0 to 999 (0.1 s)

1910 (PR)

(run) (run) specifies a time-out from when the NC (slave station) outputs usual sequence data to when the next usual sequence data is input. If the time-out is exceeded, an emergency stop occurs and the system waits for the preparation sequence to start. If the set value is 0, no time-out occurs or no communication stop can be detected.

1911 (PR)

clock select Select an operation cycle. 0: 6 MHz 1: 10 MHz

5. Base Specifications Parameters

II - 91

(SETUP PARAM 1. 15/15)

# Items Details Setting range (unit) 1925 EtherNet Start of service Start or stop the Ethernet communication function.

0: Stop 1: Start

0/1

1926 IP address

IP address Specify the NC IP address

1927 Subnet mask

Subnet mask Specify the subnet mask.

1928 Gateway address

Gateway Specify the gateway IP address.

Set these parameters in accordance with the network rules in the connection environment.

1929 Port number

Port No. Set the port No. for the service function. 1 to 9999 (Set 2000 when not connected to the Ethernet.)

1930 Host address

Host address Set the host's IP address. 1 to 255

1931 Host number

Host No. Set the host's port No. 1 to 9999

1932 FTP Retry FTP communica- tion retry times

Set the number of times to retry automatically when FTP communication fails.

0 to 999

1933 FTP Timeout

FTP communica- tion time-out interval

Set the communication time-out interval (seconds) when FTP communication automatic retry is set. If "0" is set, "10" seconds (default value) is applied.

0 to 99

(Note) Always set #1925 to #1931 when the FCU6-EP203-1 is mounted.

6. Axis Specifications Parameters 6.1 Axis Specifications Parameters

II - 92

6. Axis Specifications Parameters

6.1 Axis Specifications Parameters

After setting up the parameter (PR) listed in the table, turn OFF the NC power. To validate the parameter, turn ON the power again.

(SETUP PARAM 2. 1/8) # Items Details Setting range (unit)

2001 rapid Rapid traverse rate

Set up the rapid traverse feedrate for each axis. The maximum value to be set differs with mechanical systems.

1 to 999999 (mm/min)

2002 clamp Cutting feedrate for clamp function

Define the maximum cutting feedrate for each axis. Even if the feedrate in G01 exceeds this value the clamp will be applied at this feedrate.

1 to 999999 (mm/min)

2003 (PR)

smgst Acceleration and deceleration modes

Specify acceleration and deceleration control modes.

O T3

F E D C B A 9 8 7 6 5 4 3 2 1 0 O T2 O T1 C3 C1 LC R3 R1 LR

Note: Set 0 in null bits. (Bit2 and bit6 when the

acceleration/deceleration by software is selected are excluded.)

(To be continued to the next page)

Rapid traverse feed acceleration and deceleration types LR Linear acceleration/

deceleration R1 Primary delay R3 Exponential acceleration

and linear deceleration bit0 to 3 ON Acceleration/

deceleration by software Cutting feed acceleration and deceleration types LC Linear acceleration/

deceleration C1 Primary delay C3 Exponential acceleration

and linear deceleration bit4 to 7 ON Acceleration/

deceleration by software

Specify the modes in hexadecimal notation.

6. Axis Specifications Parameters 6.1 Axis Specifications Parameters

II - 93

# Items Details Setting range (unit) (Continued from the previous page)

Rapid traverse R3(bit3) -(bit2) R1(bit1) LR(bit0) Cutting feed C3(bit7) -(bit6) C1(bit5) LC(bit4)

Step 0 0 0 0 Linear

acceleration/ deceleration

0 0 0 1

Primary delay 0 0 1 0

Exponential acceleration and linear

deceleration

1 0 0 0

A cc

el er

at io

n/ de

ce le

ra tio

n ty

pe s

Acceleration/ deceleration by software

1 1 1 1

R1 > R3 when both R1 and R3 contain 1.

G0t1

Speed Stroke end signal

Time

2 G0t 1 (OT1=1,OT2=OT3=0) G0t 1 (OT1=OT2=OT3=0)

OT1 is valid under the following conditions (valid for dog type zero point return): Stop type: Linear deceleration Acceleration mode: Exponential Deceleration mode: Linear

Type OT2 OT3 Linear deceleration 0 0 Position loop step stop 1 0 Speed loop step stop 0 1 Position loop step stop 1 1

OT1 0 Deceleration by G0t1 1 Deceleration by 2 G0t1

6. Axis Specifications Parameters 6.1 Axis Specifications Parameters

II - 94

# Items Details Setting range (unit)

2004 G0tL G0 time constant (linear)

Set up a linear control time constant for rapid traverse acceleration and deceleration. The time constant is validated when LR (rapid traverse feed with linear acceleration or deceleration) or F (acceleration or deceleration by software) is selected in acceleration or deceleration mode "#2003 smgst".

G0tL

Speed

G0tL

Time

1 to 4000 (ms)

2005 G0t1 G0 time constant (primary delay) Second-step time constant for acceleration and deceleration by software

Set up a primary-delay time constant for rapid traverse acceleration and deceleration. The time constant is validated when R1 (rapid traverse feed with primary delay) or R3 (exponential acceleration and linear deceleration) is selected in acceleration or deceleration mode "#2003 smgst". When acceleration or deceleration by software is selected, the second-step time constant is used.

G0t1

Speed

2 G0t1

Time

G0t1

Speed

Time

G0t1

1 to 5000 (ms)

2006 G0t2 Not used. 0

6. Axis Specifications Parameters 6.1 Axis Specifications Parameters

II - 95

# Items Details Setting range (unit)

2007 G1tL G1 time constant (linear)

Set up a linear control time constant for cutting acceleration and deceleration. The time constant is validated when LC (cutting feed with linear acceleration and deceleration) or F (acceleration and deceleration by software) is selected in acceleration or deceleration mode "#2003 smgst".

G1tL

Speed

G1tL

Time

1 to 4000 (ms)

2008 G1t1 G1 time constant (primary delay) Second stage time constant for acceleration and deceleration by software

Set up the primary delay time constant for cutting acceleration and deceleration. The time constant is validated when C1 (cutting feed with the primary delay) or C3 (cutting feed with exponential acceleration and linear deceleration) is selected in acceleration or deceleration mode "#2003 smgst". When acceleration or deceleration by software is selected, the second stage time constant is used.

G1t1

Speed

2 G1t1

Time

G1t1

Speed

Time

G1t1

1 to 5000 (ms)

2009 G1t2 Not used. 0

6. Axis Specifications Parameters 6.1 Axis Specifications Parameters

II - 96

# Items Details Setting range (unit)

2010 fwd_g Feed forward gain

Set up a feed forward gain for pre-interpolation acceleration and deceleration. The larger the set value, the smaller the theoretical control error will be. However, if a mechanical vibration occurs, the set value must be reduced.

0 to 100 (%)

2011 G0back G0 backlash

Set up the backlash compensation amount when the direction is reversed with the movement command in rapid traverse feed mode or in manual mode.

-32768 to 32767

2012 G1back G1 backlash

Set up the backlash compensation amount when the direction is reversed with the movement command in cutting mode.

-32768 to 32767

6. Axis Specifications Parameters 6.1 Axis Specifications Parameters

II - 97

(SETUP PARAM 2. 2/8)

# Items Details Setting range (unit) 2013 2014

0T - 0T +

Soft limit I - soft limit I +

Set up a soft limit area with reference to the zero point of the basic mechanical coordinates. For the movable area of stored stroke limit 1, set the coordinate in the negative direction in #2013 and the coordinate in the positive direction in #2014. To narrow the available range in actual use, use the parameters #8204 OT- and #8205 OT+. When the same value (other than 0) is set in #2013 and #2014, this function is disabled.

M

OT+ (Z)

OT- (Z)OT+ (X)

OT- (X)

Basic mechanical coordinates

Movable area

99999.999 (mm)

2015 t1m1- Negative direction sensor of tool setter or TLM standard length

Set up a sensor position in the negative direction when using the tool setter. When the TLM is used, set up the distance of a tool replacement point (reference point) for measuring the tool length from the zero point to the measurement reference point (surface).

99999.999 (mm)

2016 t1m1+ Positive direction sensor of tool setter

Set up the sensor position in the positive direction when using the tool setter.

99999.999 (mm)

2017 tap_g Axis servo gain Set the position loop gain for special operations (synchronized tapping, interpolation with spindle C axis, etc.) The setting range is 1.00 to 200.00rad/s. in 0.25 increment units. The standard setting is 10.

1.00 to 200.00 (rad/s)

2018 no_srv Operation with no servo control

Set when performing test operation without connecting the drive amplifier and motor.

0: Specify normal operation. 1: Operation is possible even if units are not

connected as the drive system alarm will be ignored.

This is for test operation during start up and is not used normally. If 1 is set during normal operation errors will not be detected even if they occur.

0/1

6. Axis Specifications Parameters 6.1 Axis Specifications Parameters

II - 98

# Items Details Setting range (unit)

2019 revnum Return steps Set up the steps required for reference point return for each axis.

0: Does not execute reference point return. 1 to max. number of NC axes: Sets up the steps required for reference point return.

0 to max. number of NC axes

2020 o_chkp Spindle orientation completion check during second zero point return

Set up the distance from the second zero point to the position for checking that the spindle orientation has completed during second zero point return. If the set value is 0, the above check is omitted.

0 to 99999.999 (mm)

2021 out_f Maximum speed outside soft limit range

Set up the maximum speed outside the soft limit range.

0 to 999999

2022 G30SLX Validate soft limit (automatic and manual)

Set up this function to disable a soft limit check during the second to the fourth zero point return in both automatic and manual operation modes.

0: Enables soft limit check. 1: Disables soft limit check.

0/1

2023 ozfmin Set up ATC speed lower limit

Set up the minimum speed outside the soft limit range during the second to the fourth zero point return in both automatic and manual operation modes.

0 to 999999

2024 synerr Allowable error Set up the following for the master axis: the maximum synchronization error that is allowed to check for synchronization errors When 0 is set up, the error check is not carried out.

0 to 99999.999 (mm) During spindle C axis synchronization control: 0 to 99999.999 ()

6. Axis Specifications Parameters 6.2 Zero Point Return Parameters

II - 99

6.2 Zero Point Return Parameters

After setting up the parameter (PR) listed in the table, turn OFF the NC power. To validate the parameter, turn ON the power again.

(SETUP PARAM 2. 3/8) # Items Details Setting range (unit)

2025 G28rap G28 rapid traverse rate

Set up a rapid traverse rate for dog type reference point return command.

1 to 999999 (mm/min)

2026 G28crp G28 approach speed

Set up the speed of approach to the reference point in the reference point return command. This speed is attained after the system stops with deceleration by dog detection. Note) The G28 approach speed unit is (10/min) only

when using the Z-phase type encoder (#1226 aux10 bit3=1) for the spindle/C-axis reference point return type. The same unit is used for both the micron and sub-micron specifications.

1 to 60000 (mm/min)

2027 G28sft Reference point shift distance

Set up the distance from the electrical zero-point detection position to the actual machine reference point during reference point return control. Note) When #1240 set12 (bit2) is ON, a

magnification (C: 10-fold, D: 100-fold) corresponding to the input setting unit (#1003 iunit) will be applied on the setting value.

0 to 65535 (m)

2028 grmask Grip mask amount

Set up a distance where the grid point is ignored when near-point dog OFF signals are close to that grid point during reference point return.

The grid mask is valid by one grid.

0 to 65535 (m) Even for the specifications in sub-microns, set up the value in units of m.

2029 grspc Grid interval Set up a detector grid interval. Generally, set up the value equal to the ball screw pitch. However, if the detector grid interval is not equal to the screw pitch when measured with a linear scale, set up the detector grid interval. To reduce the grid interval, use its divisors. To use 0.001 mm as minimum setup units, set up the negative value. Example) Setup value

1 1.000 mm () -1 0.001 mm ()

Even when the specifications in sub-microns are used, 0.001 mm is specified for the minimum setup units.

-32767 to 999 (mm)

6. Axis Specifications Parameters 6.2 Zero Point Return Parameters

II - 100

# Items Details Setting range (unit)

2030 (PR)

dir (-) Reference point direction (-)

Set which side of the near-point dog the reference point is at during reference point return.

Negative direction

Positive direction

dir(-)=0

dir(-)=1

Near-point dog

Direction in which zero point is established as viewed from the near-point dog

0: Positive direction 1: Negative direction

2031 noref Axis without reference point

Specify the axis that does not have a reference point. Before automatic operation starts, reference point return is not required.

0: Normal controlled axis

1: Axis without reference point

2032 nochk Whether reference point return is completed not checked

The absolute and incremental commands can be executed even if dog type (or Z phase pulse system) reference point return is not completed. Specify whether to check that the reference point return is completed.

0: Reference point return completion is checked.

1: Reference point return completion is not checked.

2033 zp_no Z phase pulse system reference point return spindle encoder No.

The reference point return is performed with the Z phase pulse of the spindle encoder. Set the spindle encoder No. to be used.

0: Dog type 1 to 4: Spindle No.

6. Axis Specifications Parameters 6.2 Zero Point Return Parameters

II - 101

(SETUP PARAM 2. 4/8)

# Items Details Setting range (unit) 2037 2038 2039 2040

G53ofs #2_rfp #3_rfp #4_rfp

Reference point #1 to #4

Set up the position of the first, second, third, and fourth reference points from the zero point of the basic mechanical coordinates.

Basic mechanical coordinates

M Reference point #1

Reference point #2

Reference point #3 Reference point #4

999999.999 (mm)

6. Axis Specifications Parameters 6.3 Absolute Position Parameters

II - 102

6.3 Absolute Position Parameters

(SETUP PARAM 2. 5/8) # Items Details Setting range (unit)

2049 (PR)

type Absolute position detection method

Specify the absolute position zero point alignment method.

0: Not absolute position detection 1: Stopper method (push with mechanical stopper) 2: Origin point alignment method (align with

marked point) 3: Dog-type (align with dog and proximity switch) 4: Reference point alignment method II (align to

alignment mark) (Type that does not return grid after reference

alignment) 9: Simple absolute position

(Not absolute position detection but the position when the power is turned off is registered.)

Automatic initial setting is valid only when the stopper method is selected.

0 to 9

2050 absdir Base point of Z direction

Set the direction of the absolute position reference point (grid point immediately before) seen from the machine reference point for when using reference point alignment.

0: Positive direction 1: Negative

direction

2051 check Check Set the tolerable range for the movement amount (deviation amount) when the power is turned OFF.

0: Not checked 1 to 99999.999mm: If the difference of the position when the power is turned OFF

and turned ON again is larger than this value an alarm will be output.

0 to 99999.999 (mm)

2052 absg28 Not used. 2053 absm02 Not used. 2054 clpush Current limit

(%) Set up the current limit value for the initial setting when detecting an absolute position with a dog-less system. The setup value is the ratio of the current limit value to the rated value.

0 to 100 (%)

2055 pushf Push speed Set the feedrate for the automatic initial setting during stopper method.

1 to 999 (mm/min)

2056 aproch Approach Set the approach distance for the automatic initial setting in the push method. Approach distance: After using stopper once the

tool returns this distance and then use stopper again. When set to 0 the reference point coordinates set in #2037 G53ofs will be used as the approach start position.

0 to 999.999 (mm)

6. Axis Specifications Parameters 6.3 Absolute Position Parameters

II - 103

# Items Details Setting range (unit)

2057 nrefp Near zero point +

Set the width where the near-reference-point signal is output. (Positive direction width) When set to 0 the width is equivalent to the grid width setting. Note: When #1240 set12 (bit2) is ON, a magnification

(C: 10-fold, D: 100-fold) corresponding to the input setting unit (#1003 iunit) will be applied on the setting value.

0 to 32.767 (mm)

2058 nrefn Near zero point -

Set the width where the near-reference-point signal is output. (Negative direction width) When set to 0 the width is equivalent to the grid width setting. Note: When #1240 set12 (bit2) is ON, a magnification

(C: 10-fold, D: 100-fold) corresponding to the input setting unit (#1003 iunit) will be applied on the setting value.

0 to 32.767 (mm)

2059 zerbas Select zero point parameter and reference point

Specify the position to be the zero point coordinate during absolute position initial setting.

0: Position that was stopped during stopper method

Specify the coordinates of the alignment mark position when using the reference point method.

1: Grid point just before stopper Specify the coordinates of the grid point just

before the alignment mark.

0/1

6. Axis Specifications Parameters 6.4 Axis Specifications Parameters 2

II - 104

6.4 Axis Specification Parameters 2

(SETUP PARAM 2. 6/8) # Items Details Setting range (unit)

2061 OT_1B- Soft limit IB- Set up the coordinates of the lower limit of the inhibited area of stored stroke limit IB. Specify a value in the basic mechanical coordinates system. If the same value (non-zero) with the same sign as that of #2062 OT_IB+ is specified, the stored stroke limit IB function is disabled.

99999.999 (mm)

2062 OT_1B +

Soft limit IB+ Set up the coordinates of the upper limit of the inhibited area of stored stroke limit IB. Specify a value in the basic mechanical coordinates system.

99999.999 (mm)

2063 OT_1B type

Soft limit IB type

Select OT_IB or OT_IC in which OT_IB+/- is used in stored stroke limit I.

0: Soft limit IB valid 1: Soft limit IB and IC invalid 2: Soft limit IC valid 3: When using the inclined axis specifications, the

soft limit is checked with the program coordinate system.

Note: This is invalid for axes other than the inclined axis' base axis and inclined axis.

0/1/2/3

2064 rapid2 Speed 2 Specify the speed applicable to the speed area for 2-stage acceleration/deceleration. If the following conditions are not satisfied, inclination constant acceleration/deceleration is used for operation. (0 < rapid2 < rapid and rapid3 = 0 and 0 < G0tL2

traverse content multistage acceleration/deceleration) #2065 G0tL2 (Time constant 2)

0 to 999999 (mm/min) 0: No setting

2065 G0tL2 Time constant 2

Specify the time constant applicable to the speed area for 2-stage acceleration/deceleration. If the following conditions are not satisfied, inclination constant acceleration/deceleration is used for operation. (0 < rapid2 < rapid and rapid3 = 0 and 0 < G0tL2

traverse content multistage acceleration/deceleration) #2064 rapid2 (Speed 2)

1 to 4000 (ms) 0: No setting

6. Axis Specifications Parameters 6.4 Axis Specifications Parameters 2

II - 105

# Items Details Setting range (unit)

2066 rapid3 Speed 3 Specify the speed applicable to the speed area for 2-stage or 3-stage acceleration/deceleration. If the following conditions are not satisfied, inclination constant acceleration/deceleration is used for operation. (0 < rapid3 < rapid2 < rapid and 0 < G0tL3 < G0tL) (Applicable only to M64 D version series) Related parameters: #1223 aux07 bit 0 (Rapid

traverse content multistage acceleration/deceleration) #2067 G0tL3 (Time constant 3)

0 to 999999 (mm/min) 0: No setting

2067 G0tL3 Time constant 3

Specify the time constant applicable to the speed area for 2-stage or 3-stage acceleration/deceleration. If the following conditions are not satisfied, inclination constant acceleration/deceleration is used for operation. (0 < rapid3 < rapid2 < rapid and 0 < G0tL3 < G0tL) (Applicable only to M64 D version series) Related parameters: #1223 aux07 bit 0 (Rapid

traverse content multistage acceleration/deceleration) #2066 rapid3 (Speed 3)

1 to 4000 (ms) 0: No setting

2068 G0fwdg G00 feed forward gain

Specify the feed forward gain applicable to acceleration/deceleration before G00 interpolation. The greater the set value, the shorter the positioning time during in-position checking. If machine vibration occurs, decrease the set value.

0 to 200 (%)

2069 Rcoeff Axis arc radius error correction efficient

The amount of arc radius error correction can be increased or decreased between -100% to +100% for each axis.

-100.0 to +100.0 (%)

2070 (PR)

div_RT Rotational axis division count

Specify the number of divisions of one turn of the rotational axis for purpose of control. Example: When 36 is set, one turn is supposed to be

36.000. Note 1: When 0 is set, the normal rotational axis

(360.000 degrees for one turn) is assumed. Note 2: If this parameter is changed when the absolute

position detection specification is used, absolute position data is lost. Initialization must be performed again.

0 to 999

6. Axis Specifications Parameters 6.4 Axis Specifications Parameters 2

II - 106

# Items Details Setting range (unit)

2071 s_axis (For L system only)

Inclined axis selection

Select the axis subjected to inclined-axis control or the base axis corresponding to the inclined axis.

0: Axis not subjected to inclined-axis control 1: Inclined axis 2: Base axis corresponding to inclined axis

Note: Set 1 or 2 for only one axis. If it is set for two or more axes, inclined-axis control does not work.

0 to 2

2072 rslimt Restart limit If the machine is positioned on the minus (-) side of the set value in T-command restart mode, restart search in type 3 is disabled.

9999.999 (mm)

6. Axis Specifications Parameters 6.4 Axis Specifications Parameters 2

II - 107

(SETUP PARAM 2. 7/8)

# Items Details Setting range (unit) 2073 zrn_dog Origin dog Under the standard specifications, the origin dog signal

is assigned to a fixed device. When it is desired to assign the origin dog signal to a position other than the fixed device, specify the input device in this parameter. Note 1: This parameter is valid when 1 is set in #1226

aux10 bit 5. Note 2: When this parameter is valid, do not set the

same device number. If the same device number exists, an emergency stop occurs. However, no device number check is performed for an axis to which a signal that ignores the near-point dog signal (R157) is input.

00 to FF (HEX)

2074 H/W_OT+ H/W OT+ Under the standard specifications, the OT (+) signal is assigned to a fixed device. When it is desired to assign the OT (+) g signal to a position other than the fixed device, specify the input device in this parameter. Note 1: This parameter is valid when 1 is set in #1226

aux10 bit 5. Note 2: When this parameter is valid, do not set the

same device number. If the same device number exists, an emergency stop occurs. However, no device number check is performed for an axis to which a signal that ignores the OT signal (R156) is input.

00 to FF (HEX)

2075 H/W_OT- H/W OT- Under the standard specifications, the OT (-) signal is assigned to a fixed device. When it is desired to assign the OT (-) g signal to a position other than the fixed device, specify the input device in this parameter. Note 1: This parameter is valid when 1 is set in #1226

aux10 bit 5. Note 2: When this parameter is valid, do not set the

same device number. If the same device number exists, an emergency stop occurs. However, no device number check is performed for an axis to which a signal that ignores the OT signal (R156) is input.

00 to FF (HEX)

6. Axis Specifications Parameters 6.4 Axis Specifications Parameters 2

II - 108

# Items Details Setting range (unit)

2076 index_x Index table indexing axis

Specify the index table indexing axis. 0: Normal axis 1: Index table indexing axis Note: This parameter is valid only for the NC axis. The

parameter is invalid if specified for the PLC axis.

0/1

2077 G0inps G0 in-position width

When an in-position check is performed for G0, this parameter is valid. (Comparison of SV024 and this parameter, the parameter that the in-position width is wider is applied.) When 0 is set, this parameter is invalid. (Applicable only to SV024)

0 to 32767 (m) M64 specifies a 0.5 m unit.

2078 G1inps G1 in-position width

When an in-position check is performed for G1, this parameter is valid. (Comparison of SV024 and this parameter, the parameter that the in-position width is wider is applied.) When 0 is set, this parameter is invalid. (Applicable only to SV024)

0 to 32767 (m) M64 specifies a 0.5 m unit.

2079 chcomp Chopping compensa- tion coefficient

Set the coefficient applied on the compensation amount for the insufficient amount caused by servo delay during chopping.

0 to 10 (standard value: 8)

2080 chwid Bottom dead center position width

Set the tolerance between the commanded stroke and actual stroke. During chopping, if the (command width - maximum stroke of top/bottom dead center position /2) is within this tolerance, compensation will be applied.

Micron: 0 to 10000 (m) Sub-micron: 0 to 10000 (0.1 m)

2081 chclsp Maximum chopping speed

Set the chopping axis clamp speed applied during chopping.

Micron: 0 to 60000 (mm/min) Sub-micron: 0 to 60000 (0.1 mm)/min

2082 a_rstax Restart position return order

Designate the order for automatically returning to the restart position.

0: Do not return. When 0 is designated for all axes, all of the axes

will return simultaneously.

0 to 6

6. Axis Specifications Parameters 6.4 Axis Specifications Parameters 2

II - 109

# Items Details Setting range (unit)

2083 rot_2 Linear type rotary axis II

The linear type rotary axis II is validated. 0: Invalidate linear type rotary axis II. 1: Validate linear type rotary axis II.

Note that this is valid only when the power is turned ON, and the rotary axis parameters must be validated. The axis type is determined by the combination with the existing rotary axis parameters (#1017 rot rotary axis). If #1017 is set to 0, the linear axis will be applied. When #1017 is set to 1 and this parameter is set to 0, the rotary axis will be applied, and when set to 1, the linear type rotary axis II will be applied. #1089: Cut_RT Short cut for rotary axis #1090: Lin_RT Linear type rotary axis #2070: div_RT Rotary axis division count #2076: index_x Index table indexing axis Note: These parameters are invalid when the linear

type rotary axis II is set.

0/1

2084 G60_ax Unidirectional positioning operation selection

Select the unidirectional positioning with G00. Select the axis for carrying out the positioning per time operation when the positioning command is issued regardless of the unidirectional positioning command and modal.

0: Carry out unidirectional positioning according to the command and modal.

1: When the positioning command (G00) is issued, carry out unidirectional positioning regardless of the command and modal.

#8209 G60 SHIFT: The final positioning direction and distance

for the unidirectional positioning command is set for each axis.

#2076 Index table indexing axis: Set the indexing axis for each axis.

0/1

6. Axis Specifications Parameters 6.4 Axis Specifications Parameters 2

II - 110

(SETUP PARAM 2. 8/8)

# Items Details Setting range (unit) 2086 exdcax External

deceleration speed

Set the upper limit of the feedrate for each axis when the external deceleration signal is valid. This parameter is valid when the #1239 set11/bit6 external deceleration axis compliance valid is set to 1.

1 to 999999 (mm/min)

2087 syncnt Synchroniza- tion/super- imposition control setting for each axis

Set the polarity of synchronous axis in respect to basic axis to the bit corresponding to each axis.

0: Polarity with basic axis is positive 1: Polarity with basic axis is negative

0 to FF (hexadecimal)

2088 bsax_sy Reference axis for synchronous control

Set the basic axis for synchronous control with the 2nd axis name (axname2). A numerical character cannot be set to the 1st character.

Axis name

2089 bsax_pl Reference axis for superimposi- tion control

Set the basic axis for superimposition control with the 2nd axis name (axname2). A numerical character cannot be set to the 1st character.

Axis name

2090 plrapid Rapid traverse rate for super- imposition control

Set the rapid traverse rate for superimposition control. (Equivalent to #2001 rapid (rapid traverse rate).)

1 to 999999 (mm/min)

2091 plclamp Cutting feed clamp speed for super- imposition control

Set the cutting feed clamp speed for superimposition control. (Equivalent to #2002 clamp (cutting feed clamp speed).)

1 to 999999 (mm/min)

2092 plG0tL G0 time constant for superimposi- tion control (linear)

Set the G0 time constant (linear) for superimposition control. (Equivalent to #2004 G0tL (G0 time constant (linear).)

1 to 4000 (ms)

2093 plG0t1 G0 time constant for superimposi- tion control (primary delay)

Set the G0 time constant (primary delay) for superimposition control. (Equivalent to #2005 G0t1 (G0 time constant (primary delay).)

1 to 5000 (ms)

2094 plG1tL G1 time constant for superimposi- tion control (linear)

Set the G1 time constant (linear) for superimposition control. (Equivalent to #2007 G1tL (G1 time constant (linear).)

1 to 4000 (ms)

6. Axis Specifications Parameters 6.4 Axis Specifications Parameters 2

II - 111

# Items Details Setting range (unit)

2095 plG1t1 G1 time constant for superimposi- tion control (primary delay)

Set the G1 time constant (primary delay) for superimposition control. (Equivalent to #2008 G1t1 (G1 time constant (primary delay).)

1 to 5000 (ms)

2096 crncsp Minimum corner deceleration speed

Set the minimum clamp speed for corner deceleration during the high-accuracy control mode. Normally set "0". Note: This parameter is invalid during SSS control.

0 to 1000000 (mm/min)

2099 igConr Axis excluded from corner angle calculation

Set the axis excluded from the corner angle calculation. For example, set this for the Cs axis during spring machining.

0/1

2102 skip_tL Skip time constant linear

Set up a linear control time constant for variable speed skip acceleration and deceleration. The time constant is validated when LC (cutting feed with linear acceleration and deceleration) or F (acceleration and deceleration by software) is selected in acceleration or deceleration mode "#2003 smgst".

1 to 4000 (ms)

2103 skip_t1 Skip time constant primary delay acceleration and deceleration by software second stage

Set up a primary-delay time constant for variable speed skip acceleration and deceleration. The time constant is validated when C1 (cutting feed with primary delay) or C3 (exponential acceleration and linear deceleration) is selected in acceleration or deceleration mode "#2003 smgst". When acceleration or deceleration by software is selected, the second-step time constant is used.

1 to 5000 (ms)

7. Servo Parameters

II - 112

7. Servo Parameters

The parameters can be changed from any screen. The valid servo parameters will differ according to the motor type. The setting values and meanings may also differ. Follow the correspondence table given below, and set the correct parameters. Refer to each Instruction Manual or the following manuals for details on each motor.

MELDAS AC Servo/ Spindle MDS-A Series MDS-B Series Specification Manual................ BNP-B3759 MELDAS AC Servo MDS-B-SVJ2 Series Specification and Instruction Manual...................... BNP-B3937 MELDAS AC Servo/ Spindle MDS-C1 Series Specification Manual...................................... BNP-C3000

Corresponding model

Parameter MDS-B-SVJ2

MDS-C1-Vx (High-gain)

(MDS-B-Vx4)

MDS-C1-Vx (Standard) (MDS-B-Vx)

SV001 Motor side gear ratio SV002 Machine side gear ratio SV003 Position loop gain 1 SV004 Position loop gain 2 SV005 Speed loop gain 1 SV006 Speed loop gain 2 - SV007 Speed loop delay compensation - SV008 Speed loop lead compensation SV009 Current loop q axis lead compensation SV010 Current loop d axis lead compensation SV011 Current loop q axis gain SV012 Current loop d axis gain SV013 Current limit value SV014 Current limit value in special control SV015 Acceleration rate feed forward gain SV016 Lost motion compensation 1 SV017 Servo specification selection SV018 Ball screw pitch SV019 Position detector resolution SV020 Speed detector resolution SV021 Overload detection time constant SV022 Overload detection level

SV023 Excessive error detection width during servo ON

SV024 In-position detection width SV025 Motor/Detector type

SV026 Excessive error detection width during servo OFF

SV027 Servo function selection 1 SV028 Linear motor magnetic pole shift length - - - SV029 Speed at the change of speed loop gain - SV030 Voltage dead time compensation -/ / / SV031 Overshooting compensation 1 SV032 Torque offset

7. Servo Parameters

II - 113

Corresponding model

Parameter MDS-B-SVJ2

MDS-C1-Vx (High-gain)

(MDS-B-Vx4)

MDS-C1-Vx (Standard) (MDS-B-Vx)

SV033 Servo function selection 2 SV034 Servo function selection 3 SV035 Servo function selection 4 SV036 Regenerative resistor type SV037 Load inertia scale SV038 Notch filter frequency 1 - SV039 Lost motion compensation timing - SV040 Non-sensitive band in feed forward control -/ / / SV041 Lost motion compensation 2 SV042 Overshooting compensation 2 SV043 Disturbance observer filter frequency SV044 Disturbance observer gain SV045 Frictional torque -/ / / SV046 Notch filter frequency 2 - - SV047 Inductive voltage compensation gain SV048 Vertical axis drop prevention time

SV049 Position loop gain 1 in spindle synchronous control

SV050 Position loop gain 2 in spindle synchronous control

SV051 Dual feedback control time constant - SV052 Dual feedback control non-sensitive band -

SV053 Excessive error detection width in special control

SV054 Overrun detection width in closed loop control -/- / /

SV055 Max. gate off delay time after emergency stop -

SV056 Deceleration time constant at emergency stop

SV057 SHG control gain

SV058 SHG control gain in spindle synchronous control

SV059 Collision detection torque estimating gain SV060 Collision detection level SV061 D/A output channel 1 data No. SV062 D/A output channel 2 data No. SV063 D/A output channel 1 output scale SV064 D/A output channel 2 output scale SV065 Tool end compensation spring constant - -

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 114

7.1 MDS-B-SVJ2

(1) Details for servo parameters

For parameters marked with a (PR) in the table, turn the NC power OFF after setting. After the power is turned ON again, the parameter is validated.

! CAUTION

! In the explanation on bits, set all bits not used, including blank bits, to 0.

No. Items Details Setting range

2201 (PR)

SV001 PC1

Motor side gear ratio

1 to 32767

2202 (PR)

SV002 PC2

Machine side gear ratio

Set the motor side and machine side gear ratio. For the rotary axis, set the total deceleration (acceleration) ratio. Even if the gear ratio is within the setting range, the electronic gears may overflow and cause an alarm.

1 to 32767

2203 SV003 PGN1

Position loop gain 1

Set the position loop gain. The standard setting is "33". The higher the setting value is, the more precisely the command can be followed and the shorter the positioning time gets, however, note that a bigger shock is applied to the machine during acceleration/deceleration. When using the SHG control, also set SV004 (PGN2) and SV057 (SHGC).

1 to 200 (rad/s)

2204 SV004 PGN2

Position loop gain 2

When using the SHG control, also set SV003 (PGN1) and SV057 (SHGC). When not using the SHG control, set to 0.

0 to 999 (rad/s)

2205 SV005 VGN1

Speed loop gain

Set the speed loop gain. Set this according to the load inertia size. The higher the setting value is, the more accurate the control will be, however, vibration tends to occur. If vibration occurs, adjust by lowering by 20 to 30%. The value should be determined to be 70 to 80% of the value at the time when the vibration stops.

1 to 999

2206 Not used. Set to "0". 0 2207 Not used. Set to "0". 0 2208 SV008

VIA Speed loop lead compensation

Set the gain of the speed loop integration control. The standard setting is "1364". During the SHG control, the standard setting is "1900". Adjust the value by increasing/decreasing it by about 100 at a time. Raise this value to improve contour tracking precision in high-speed cutting. Lower this value when the position droop vibrates (10 to 20Hz).

1 to 9999

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 115

No. Items Details Setting range

2209 SV009 IQA

Current loop q axis lead compensation

1 to 20480

2210 SV010 IDA

Current loop d axis lead compensation

1 to 20480

2211 SV011 IQG

Current loop q axis gain

1 to 2560

2212 SV012 IDG

Current loop d axis gain

Set the gain of current loop. As this setting is determined by the motor's electrical characteristics, the setting is fixed for each type of motor. Set the standard values for all the parameters depending on each motor type.

1 to 2560

2213 SV013 ILMT

Current limit value

Set the normal current (torque) limit value. (Limit values for both + and - direction.) When the value is "500" (a standard setting), the maximum torque is determined by the specification of the motor.

0 to 500 (Stall [rated] current %)

2214 SV014 ILMTsp

Current limit value in special control

Set the current (torque) limit value in a special control (initial absolute position setting, stopper control, etc). (Limit values for both of the + and - directions.) Set to "500" when not using.

0 to 500 (Stall [rated] current %)

2215 SV015 FFC

Acceleration rate feed forward gain

When a relative error in the synchronous control is large, apply this parameter to the axis that is delaying. The standard setting value is "0". For the SHG control, set to "100". To adjust a relative error in acceleration/ deceleration, increase the value by 50 to 100 at a time.

0 to 999 (%)

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 116

No. Items Details Setting range

Set this when the protrusion (that occurs due to the non-sensitive band by friction, torsion, backlash, etc) at quadrant change is too large. This compensates the torque at quadrant change. This is valid only when the lost motion compensation (SV027 (SSF1/lmc)) is selected.

Type 1: When SV027 (SSF1)/ bit9, 8 (lmc)=01 Set the compensation amount based on the motor torque before the quadrant change. The standard setting is "100". Setting to "0" means the compensation amount is zero. Normally, use Type 2.

-1 to 200 (%)

Type 2: When SV027 (SSF1)/ bit9, 8 (lmc)=10 Set the compensation amount based on the stall (rated) current of the motor. The standard setting is double of the friction torque. Setting to "0" means the compensation amount is zero.

-1 to 100 (Stall [rated] current %)

2216 SV016 LMC1

Lost motion compensation 1

When you wish different compensation amount depending on the direction When SV041 (LMC2) is "0", compensate with the value of SV016 (LMC1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV041 (LMC2). (SV016: + direction, SV041: - direction. However, the directions may be opposite depending on other settings.) When "-1" is set, the compensation won't be performed in the direction of the command.

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 117

No. Items Details Setting range

2217 (PR)

SV017 SPEC

Servo specification selection

F E D C B A 9 8

7 6 5 4 3 2 1 0 abs vdir mc dmk

bit Meaning when "0" is set Meaning when "1" is set

0 dmk Deceleration control stop (SVJ2 standard) Dynamic brake stop

1 2 3 mc Contactor control output invalid Contactor control output valid 4

5 vdir HA053N to HA33N motor Detector installation position standard (A, C)

HA053N to HA33N motor Detector installation position 90 degrees (B, D)

6 7 abs Incremental control Absolute position control 8 9 A B C D E F

(Note) Set to "0" for bits with no particular description. 2218 (PR)

SV018 PIT

Ball screw pitch

Set the ball screw pitch. Set to 360 for the rotary axis. 1 to 32767 (mm/rev)

For both parameters, set the number of pulses per one revolution of the motor detector. Setting value

2219 (PR)

SV019 RNG1

Position detector resolution

Motor model name

SV019 SV020 HC*-E42/A42/A47, HC*R-E42/A42/A47 HA*N-E42/A42

100 100

HC*-E33/A33, HC*R-E33/A33 HA*N-E33/A33

25 25

HC-SF, HC-RF 16 16 HA-FF, HC-MF 8 8

2220 (PR)

SV020 RNG2

Speed detector resolution

8 to 100 (kp/rev)

2221 SV021 OLT

Overload detection time constant

Set the detection time constant of Overload 1 (Alarm 50). Set to "60" as a standard. (For machine tool builder adjustment.)

1 to 300 (s)

2222 SV022 OLL

Overload detection level

Set the current detection level of Overload 1 (Alarm 50) in respect to the stall (rated) current. Set to "150" as a standard. (For machine tool builder adjustment.)

50 to 180 (Stall [rated] current %)

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 118

No. Items Details Setting range

Set the excessive error detection width when servo ON.

Rapid traverse rate (mm/min)

OD1=OD2= 60*PGN1

/2 (mm)

2223 SV023 OD1

Excessive error detection width during servo ON

When "0" is set, the excessive error detection will not be performed.

0 to 32767 (mm)

2224 SV024 INP

In-position detection width

Set the in-position detection width. Set the accuracy required for the machine. The lower the setting is, the higher the positioning accuracy gets, however, the cycle time (setting time) becomes longer. The standard setting is "50".

0 to 32767 (m)

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 119

No. Items Details Setting range

2225 (PR)

SV025 MTYP

Motor/ Detector type

F E D C B A 9 8 pen ent

7 6 5 4 3 2 1 0 mtyp

bit Explanation

0 Set the motor type.

1 Set- ting 0x 1x 2x 3x 4x 5x 6x 7x 8x

2 x0 HA40N HA-FF43 HA43N 3 x1 HA80N HA-FF63 HA83N 4 x2 HA100N HA103N 5 x3 HA200N 6 x4 7

mtyp

x5 x6 x7 x8 x9 xA HA93N xB xC HA-FF053 HA053N xD HA-FF13 HA13N xE HA-FF23 HA23N xF HA-FF33 HA33N

Set- ting 9x Ax Bx Cx Dx Ex Fx

x0 HC-MF43 HC52 or HC-SF52

HC53 or HC-SF53

x1 HC-MF73 HC102 or HC-SF102

HC103 or HC-SF103 HC103R or

HC-RF103

x2 HC152 or HC-SF152

HC153 or HC-SF153 HC153R or

HC-RF153

x3 HC202 or HC-SF202

HC203 or HC-SF203 HC203R or

HC-RF203

x4 HC352 or HC-SF352HC-SF353

x5 x6 x7 x8 x9 xA xB xC HC-MF053 xD HC-MF13 xE HC-MF23 xF

(To be continued to the next page)

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 120

No. Items Details Setting range

(Continued from the previous page)

bit Explanation 8 9 A B

ent

Set the speed detector type. Set to "2".

C D E F

pen

Set the position detector type. Set to "2".

2226 SV026

OD2 Excessive error detection width during servo OFF

Set the excessive error detection width when servo ON. For the standard setting, refer to the explanation of SV023 (OD1). When "0" is set, the excessive error detection will not be performed.

0 to 32767 (mm)

2227 SV027 SSF1

Servo function selection 1

F E D C B A 9 8 aflt zrn2 ovs lmc

7 6 5 4 3 2 1 0 vfct zup

bit Meaning when "0" is set Meaning when "1" is set

0 zup Vertical axis lift-up control stop Vertical axis lift-up control start

1 2 3

4 Set the jitter compensation No. of compensation pulses with a binary.

5 vfct

00: Jitter compensation invalid 01: Jitter compensation 1 pulse 10: Jitter compensation 2 pulses 11: Jitter compensation 3 pulses

6 7

8 Set the compensation amount with SV016 (LMC1) and SV041 (LMC2).

9 lmc

00: Lost motion compensation stop 01: Lost motion compensation type 1 10: Lost motion compensation type 2 11: Setting prohibited

A Set the compensation amount with SV031 (OVS1) and SV042 (OVS2).

B ovs

00: Overshooting compensation stop 01: Overshooting compensation type 1 10: Overshooting compensation type 2 11: Setting prohibited

C D E zrn2 Set to "1". F aflt Adoptive filter stops Adoptive filter starts

(Note) Set to "0" for bits with no particular description. 2228 SV028 Not used. Set to "0". 0 2229 SV029 Not used. Set to "0". 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 121

No. Items Details Setting range

2230 SV030 IVC

Voltage dead time compensa- tion

When 100% is set, the voltage equivalent to the logical non-energized time will be compensated. Adjust in increments of 10% from the default value 100%. If increased too much, vibration or vibration noise may be generated. When not using, set to "0".

0 to 200 (%)

Set this if overshooting occurs during positioning. This compensates the motor torque during positioning. This is valid only when the overshooting compensation SV027 (SSF1/ovs) is selected. Type 1: When SV027 (SSF1)/ bit11, 10 (ovs)=01 Set the compensation amount based on the motors stall (rated) current. Increase by 1% and determine the amount that overshooting doesnt occur. In Type 1, compensation during the feed forward control during circular cutting wont be performed. Type 2: When SV027 (SSF1)/ bit11, 10 (ovs)=10 Use this if you perform the overshooting compensation during the feed forward control during circular cutting. The setting method is the same in Type 1.

2231 SV031 OVS1

Overshoot- ing compensa- tion 1

When you wish different compensation amount depending on the direction When SV042 (OVS2) is "0", compensate with the value of SV031 (OVS1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV042 (OVS2). (SV031: + direction, SV042: - direction. However, the directions may be opposite depending on other settings.) When "-1" is set, the compensation wont be performed in the direction of the command.

-1 to 100 (Stall [rated] current %)

2232 SV032 TOF

Torque offset

Set the unbalance torque of vertical axis and inclined axis.

-100 to 100 (Stall [rated] current %)

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 122

No. Items Details Setting range

2233 SV033 SSF2

Servo function selection 2

F E D C B A 9 8 afs

7 6 5 4 3 2 1 0 fhz2 nfd

bit Meaning when "0" is set Meaning when "1" is set

0 Set the filter depth for Notch filter (SV038: FHz1). 1 The control is stabilized by making the filter shallower. 2 Value 0 2 4 6 8 A C E

3

nfd Depth (dB)

Infntly deep -18.1 -12.0 -8.5 -6.0 -4.1 -2.5 -1.2

Deep Shallow 4 Set the operation frequency of Notch filter 2. 5 fhz2 00: No operation 01:2250Hz 10:1125Hz 11:750Hz 6 7 8 9 A B

afs

Set the vibration sensitivity of the adaptive filter. If the filter depth is not deep enough (generally 70% or more) and the vibration cannot be sufficiently eliminated, raise the value.

C D E F

(Note) Set to "0" for bits with no particular description.

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 123

No. Items Details Setting range

2234 SV034 SSF3

Servo function selection 3

F E D C B A 9 8

7 6 5 4 3 2 1 0 daf2 daf1 dac2 dac1 mon

bit Meaning when "0" is set Meaning when "1" is set 0 NC servo monitor MAX current display data changeover

1 Set- ting MAX current 1 MAX current 2

2

0 Max. current command value when power is turned ON (%)

Max. current command value for one second (%)

3

mon

1 Max. current command value for one second (%)

Max. current FB value for one second (%)

2 Max. current FB value when power is turned ON (%)

Max. current FB value for one second (%)

3 Load inertia rate (%) -

4 Adaptive filter operation frequency (Hz)

Adaptive filter operation gain (%)

5 PN bus voltage (V) Regenerative operation

frequency monitor (The number of times/sec)

6 Estimated max. torque for one second (%)

Max. current FB value for one second (%)

7 Estimated max. torque for one second (%)

Max. disturbance torque for two seconds (%)

8 to F Setting prohibited

4 dac1 D/A output ch.1 overflow setting D/A output ch.1 clamp setting 5 dac2 D/A output ch.2 overflow setting D/A output ch.2 clamp setting 6 daf1 D/A output ch.1 no filter D/A output ch.1 filter setting 7 daf2 D/A output ch.2 no filter D/A output ch.2 filter setting 8 9 A B C D E F

(Note) Set to "0" for bits with no particular description.

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 124

No. Items Details Setting range

2235 SV035 SSF4

Servo function selection 4

F E D C B A 9 8 cl2n clG1

7 6 5 4 3 2 1 0

bit Meaning when "0" is set Meaning when "1" is set 0 1 2 3 4 5 6 7 8 9 A B C D

E clG1

Collision detection method 1 Set the collision detection level during cutting feed (G1). The G1 collision detection level=SV060*clG1. When clG1=0, the collision detection method 1 during cutting feed wont function.

F cl2n Collision detection method 2 valid

Collision detection method 2 invalid

(Note) Set to "0" for bits with no particular description.

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 125

No. Items Details Setting range

2236 (PR)

SV036 PTYP

Regenera- tive resistor type

F E D C B A 9 8 amp rtyp

7 6 5 4 3 2 1 0 emgx

bit Explanation 0 1 2 3

Always set to "0(0000) ".

4 Set the external emergency stop function. (Setting is prohibited for values with no description.)

5 Set- ting Explanation

6 0 External emergency stop invalid 7

emgx

4 External emergency stop valid 8 Set the regenerative resistor type.

9 Set- ting Explanation

A 0 Drive unit standard built-in resistor (SVJ2-01 doesnt have a built-in resistor)

B

rtyp

1 Setting prohibited 2 MR-RB032 3 MR-RB12 or GZG200W390HMK

4 MR-RB32 or GZG200W1200HMK: 3 units connected in parallel

5 MR-RB30 or GZG200W390HMK: 3 units connected in parallel

6 MR-RB50 or GZG300W390HMK: 3 units connected in parallel

7 to F Setting prohibited

C D E F

amp

Always set to "0(0000) ".

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 126

No. Items Details Setting range

Set "the motor inertia + motor axis conversion load inertia" in respect to the motor inertia.

Jl+Jm SV037 (JL) =

Jm *100

Jm: Motor inertia

2237 SV037 JL Load inertia scale

Jl: Motor axis conversion load inertia

0 to 5000 (%)

2238 SV038 FHz1

Notch filter frequency 1

Set the vibration frequency to suppress if machine vibration occurs. (Valid at 72 or more) When not using, set to 0.

0 to 3000 (Hz)

2239 SV039 LMCD

Lost motion compensation timing

Set this when the lost motion compensation timing doest not match. Adjust by increasing the value by 10 at a time.

0 to 2000 (ms)

2240 SV040 LMCT

Non-sensitive band in feed forward control

Set the non-sensitive bad of the lost motion compensation and overshooting compensation during the feed forward control. When "0" is set, the actual value that will be set is 2m. Adjust by increasing by 1m.

0 to 100 (m)

2241 SV041 LMC2

Lost motion compensation 2

Set this with SV016 (LMC1) only when you wish to set the lost motion compensation amount to be different depending on the command directions. Set to "0" as a standard.

-1 to 200 (Stall [rated] current %)

2242 SV042 OVS2

Overshooting compensation 2

Set this with SV031 (OVS1) only when you wish to set the overshooting compensation amount to be different depending on the command directions. Set to "0" as a standard.

-1 to 100 (Stall [rated] current %)

2243 SV043 OBS1

Disturbance observer filter frequency

Set the disturbance observer filter band. The standard setting is "300". Lower the setting by 50 at a time if vibration occurs. To use the disturbance observer, also set SV037 (JL) and SV044 (OBS2). When not using, set to 0.

0 to 1000 (rad/s)

2244 SV044 OBS2

Disturbance observer gain

Set the disturbance observer gain. The standard setting is "100" to "300". To use the disturbance observer, also set SV037 (JL) and SV043 (OBS1). When not using, set to 0.

0 to 1000 (%)

2245 SV045 TRUB

Frictional torque

Set the frictional torque when using the collision detection function.

0 to 100 (Stall [rated] current %)

2246 SV046 Not used. Set to "0". 0 2247 SV047

EC Inductive voltage compensation gain

Set the inductive voltage compensation gain. Set to "100" as a standard. If the current FB peak exceeds the current command peak, lower the gain.

0 to 200 (%)

2248 SV048 EMGrt

Vertical axis drop prevention time

Input a length of time to prevent the vertical axis from dropping by delaying Ready OFF until the brake works when the emergency stop occurs. Increase the setting by 100ms at a time and set the value where the axis does not drop.

0 to 2000 (ms)

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 127

No. Items Details Setting range

2249 SV049 PGN1sp

Position loop gain 1 in spindle synchronous control

Set the position loop gain during the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). Set the same value as the value of the spindle parameter, position loop gain in synchronous control. When performing the SHG control, set this with SV050 (PGN2sp) and SV058 (SHGCsp).

1 to 200 (rad/s)

2250 PGN2sp Position loop gain 2 in spindle synchronous control

Set this with SV049 (PGN1sp) and SV058 (SHGCsp) if you wish to perform the SHG control in the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to "0".

0 to 999 (rad/s)

2251 SV051 Not used. Set to "0". 0 2252 SV052 Not used. Set to "0". 0 2253 SV053

OD3 Excessive error detection width in special control

Set the excessive error detection width when servo ON in a special control (initial absolute position setting, stopper control, etc.). If "0" is set, excessive error detection wont be performed when servo ON during a special control.

0 to 32767 (mm)

2254 SV054 Not used. Set to "0". 0 2255 SV055 Not used. Set to "0". 0 2256 SV056

EMGt Deceleration time constant at emergency stop

Set the time constant used for the deceleration control at emergency stop. Set a length of time that takes from rapid traverse rate (rapid) to stopping. Normally, set the same value as the rapid traverse acceleration/deceleration time constant.

0 to 5000 (ms)

2257 SV057 SHGC

SHG control gain

When performing the SHG control, set this with S003 (PGN1) and SV004 (PGN2). When not performing the SHG control, set to "0".

0 to 999 (rad/s)

2258 SV058 SHGCsp

SHG control gain in spindle synchronous control

Set this with SV049 (PGN1sp) and SV050 (PGN2sp) if you wish to perform the SHG control in the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to "0".

0 to 999 (rad/s)

2259 SV059 TCNV

Collision detection torque estimating gain

To use the collision detection function, set the torque estimating gain. In the case of MDS-B-SVJ2, the value is the same as the load inertia ratio that includes the motor inertia. (=SV037:JL) If acceleration/deceleration is performed after setting SV034.mon=3 and SV060=0, the load inertia ratio will be displayed on the NC monitor screen.

0 to 5000 (%)

2260 SV060 TLMT

Collision detection level

When using the collision detection function, set the collision detection level during the G0 feeding. If "0" is set, none of the collision detection function will work.

0 to 200 (Stall [rated] current %)

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 128

No. Items Details Setting range

2261 SV061 DA1NO

D/A output channel 1 data No.

2262 SV062 DA2NO

D/A output channel 2 data No.

Input the data number you wish to output to D/A output channel.

0 to 102

2263 SV063 DA1MPY

D/A output channel 1 output scale

2264 SV064 DA2MPY

D/A output channel 2 output scale

When "0" is set, output is done with the standard output unit. Set other than "0" when you wish to change the unit. Set the scale with a 1/256 unit. When "256" is set, the output unit will be the same as the standard output unit.

-32768 to 32767 (Unit: 1/256)

2265 SV065 Not used. Set to "0". 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 129

(2) Initial setting value

(a) HC**/HC**R series

Motor HC 52

HC 102*

HC 102

HC 152*

HC 152

HC 202*

HC 202

HC 352*

Drive unit capacity 06 07 10 10 20 10 20 20

SV001 PC1 - - - - - - - - SV002 PC2 - - - - - - - - SV003 PGN1 33 33 33 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 0 0 SV005 VGN1 50 80 50 80 50 115 80 130 SV006 0 0 0 0 0 0 0 0 SV007 0 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 8192 4096 8192 4096 8192 2048 4096 2048 SV010 IDA 8192 4096 8192 4096 8192 2048 4096 2048 SV011 IQG 512 256 384 256 384 256 384 256 SV012 IDG 512 256 384 256 384 256 384 256 SV013 ILMT 500 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - - SV019 RNG1 - - - - - - - - SV020 RNG2 - - - - - - - - SV021 OLT 60 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 150 SV023 OD1 - - - - - - - - SV024 INP 50 50 50 50 50 50 50 50 SV025 MTYP 22B0 22B1 22B1 22B2 22B2 22B3 22B3 22B4 SV026 OD2 - - - - - - - - SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 0 SV029 0 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 130

Motor HC 52

HC 102*

HC 102

HC 152*

HC 152

HC 202*

HC 202

HC 352*

Drive unit capacity 06 07 10 10 20 10 20 20

SV033 SSF2 0 0 0 0 0 0 0 0 SV034 SSF3 0 0 0 0 0 0 0 0 SV035 SSF4 0 0 0 0 0 0 0 0 SV036 PTYP - - - - - - - - SV037 JL 0 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 0 SV046 0 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 0 SV051 0 0 0 0 0 0 0 0 SV052 0 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 0 SV054 0 0 0 0 0 0 0 0 SV055 0 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 0 SV065 0 0 0 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 131

Motor HC 53

HC 103

HC 153

HC 203*

HC 103R

HC 153R

HC 203R

Drive unit capacity 06 10 20 20 10 10 20

SV001 PC1 - - - - - - - SV002 PC2 - - - - - - - SV003 PGN1 33 33 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 0 SV005 VGN1 80 80 80 100 10 10 10 SV006 0 0 0 0 0 0 0 SV007 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 4096 4096 4096 2048 8192 8192 8192 SV010 IDA 4096 4096 4096 2048 8192 8192 8192 SV011 IQG 256 256 256 200 384 384 256 SV012 IDG 256 256 256 200 384 384 256 SV013 ILMT 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - SV019 RNG1 - - - - - - - SV020 RNG2 - - - - - - - SV021 OLT 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 SV023 OD1 - - - - - - - SV024 INP 50 50 50 50 50 50 50 SV025 MTYP 22C0 22C1 22C2 22C3 22E1 22E2 22E3 SV026 OD2 - - - - - - - SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 SV029 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 132

Motor HC 53

HC 103

HC 153

HC 203*

HC 103R

HC 153R

HC 203R

Drive unit capacity 06 10 20 20 10 10 20

SV033 SSF2 0 0 0 0 0 0 0 SV034 SSF3 0 0 0 0 0 0 0 SV035 SSF4 0 0 0 0 0 0 0 SV036 PTYP - - - - - - - SV037 JL 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 SV046 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 SV051 0 0 0 0 0 0 0 SV052 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 SV054 0 0 0 0 0 0 0 SV055 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 SV065 0 0 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 133

(b) HA**N series

Motor HA 40N

HA 80N

HA 100N

HA 200N*

HA 053N

HA 13N

HA 23N

HA 33N

HA 43N

HA 83N

HA 103N*

Drive unit capacity 06 10 20 20 01 01 03 03 06 10 20

SV001 PC1 - - - - - - - - - - - SV002 PC2 - - - - - - - - - - - SV003 PGN1 33 33 33 33 33 33 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 0 0 0 0 0 SV005 VGN1 90 150 150 220 35 35 35 35 120 150 180 SV006 0 0 0 0 0 0 0 0 0 0 0 SV007 0 0 0 0 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 2048 2048 2048 2048 2048 2048 2048 2048 2048 2048 2048 SV010 IDA 2048 2048 2048 2048 2048 2048 2048 2048 2048 2048 2048 SV011 IQG 512 512 512 200 256 256 256 256 512 512 512 SV012 IDG 512 512 512 200 256 256 256 256 512 512 512 SV013 ILMT 500 500 500 500 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - - - - - SV019 RNG1 - - - - - - - - - - - SV020 RNG2 - - - - - - - - - - - SV021 OLT 60 60 60 60 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 150 150 150 150 SV023 OD1 - - - - - - - - - - - SV024 INP 50 50 50 50 50 50 50 50 50 50 50 SV025 MTYP 2200 2201 2202 2203 228C 228D 228E 228F 2280 2281 2282 SV026 OD2 - - - - - - - - - - - SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 0 0 0 0 SV029 0 0 0 0 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 134

Motor HA 40N

HA 80N

HA 100N

HA 200N*

HA 053N

HA 13N

HA 23N

HA 33N

HA 43N

HA 83N

HA 103N*

Drive unit capacity 06 10 20 20 01 01 03 03 06 10 20

SV033 SSF2 0 0 0 0 0 0 0 0 0 0 0 SV034 SSF3 0 0 0 0 0 0 0 0 0 0 0 SV035 SSF4 0 0 0 0 0 0 0 0 0 0 0 SV036 PTYP - - - - - - - - - - - SV037 JL 0 0 0 0 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 0 0 0 0 SV046 0 0 0 0 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 0 0 0 0 SV051 0 0 0 0 0 0 0 0 0 0 0 SV052 0 0 0 0 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 0 0 0 0 SV054 0 0 0 0 0 0 0 0 0 0 0 SV055 0 0 0 0 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 0 0 0 0 SV065 0 0 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 135

(c) HC-SF series

Motor HC-SF 52

HC-SF 102

HC-SF 152

HC-SF 202

HC-SF 352

HC-SF 53

HC-SF 103

HC-SF 153

HC-SF 203

HC-SF 353

Drive unit capacity 06 07 10 10 20 06 07 10 10 20

SV001 PC1 - - - - - - - - - - SV002 PC2 - - - - - - - - - - SV003 PGN1 33 33 33 33 33 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 0 0 0 0 SV005 VGN1 80 80 80 120 130 90 90 130 180 180 SV006 0 0 0 0 0 0 0 0 0 0 SV007 0 0 0 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 8192 4096 4096 2048 2048 4096 4096 2048 2048 2048 SV010 IDA 8192 4096 4096 2048 2048 4096 4096 2048 2048 2048 SV011 IQG 500 300 300 300 250 250 250 200 200 200 SV012 IDG 500 300 300 300 250 250 250 200 200 200 SV013 ILMT 500 500 500 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - - - - SV019 RNG1 16 16 16 16 16 16 16 16 16 16 SV020 RNG2 16 16 16 16 16 16 16 16 16 16 SV021 OLT 60 60 60 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 150 150 150 SV023 OD1 - - - - - - - - - - SV024 INP 50 50 50 50 50 50 50 50 50 50 SV025 MTYP 22B0 22B1 22B2 22B3 22B4 22C0 22C1 22C2 22C3 22C4 SV026 OD2 - - - - - - - - - - SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 0 0 0 SV029 0 0 0 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 136

Motor HC-SF 52

HC-SF 102

HC-SF 152

HC-SF 202

HC-SF 352

HC-SF 53

HC-SF 103

HC-SF 153

HC-SF 203

HC-SF 353

Drive unit capacity 06 07 10 10 20 06 07 10 10 20

SV033 SSF2 0 0 0 0 0 0 0 0 0 0 SV034 SSF3 0 0 0 0 0 0 0 0 0 0 SV035 SSF4 0 0 0 0 0 0 0 0 0 0 SV036 PTYP - - - - - - - - - - SV037 JL 0 0 0 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 0 0 0 SV046 0 0 0 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 0 0 0 SV051 0 0 0 0 0 0 0 0 0 0 SV052 0 0 0 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 0 0 0 SV054 0 0 0 0 0 0 0 0 0 0 SV055 0 0 0 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 0 0 0 SV065 0 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 137

(d) HC-RF/HA-FF series

Motor HC-RF 103

HC-RF 153

HC-RF 203

HA-FF 053

HA-FF 13

HA-FF 23

HA-FF 33

HA-FF 43

HA-FF 63

Drive unit capacity 10 10 20 01 01 03 03 04 06

SV001 PC1 - - - - - - - - - SV002 PC2 - - - - - - - - - SV003 PGN1 33 33 33 33 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 0 0 0 SV005 VGN1 10 10 10 10 13 13 18 20 20 SV006 0 0 0 0 0 0 0 0 0 SV007 0 0 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 8192 8192 8192 8192 4096 4096 4096 4096 4096 SV010 IDA 8192 8192 8192 8192 4096 4096 4096 4096 4096 SV011 IQG 384 384 256 500 300 700 500 700 700 SV012 IDG 384 384 256 500 300 700 500 700 700 SV013 ILMT 500 500 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - - - SV019 RNG1 16 16 16 8 8 8 8 8 8 SV020 RNG2 16 16 16 8 8 8 8 8 8 SV021 OLT 60 60 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 150 150 SV023 OD1 - - - - - - - - - SV024 INP 50 50 50 50 50 50 50 50 50 SV025 MTYP 22E1 22E2 22E3 227C 227D 227E 227F 2270 2271 SV026 OD2 - - - - - - - - - SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 0 0 SV029 0 0 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 138

Motor HC-RF 103

HC-RF 153

HC-RF 203

HA-FF 053

HA-FF 13

HA-FF 23

HA-FF 33

HA-FF 43

HA-FF 63

Drive unit capacity 10 10 20 01 01 03 03 04 06

SV033 SSF2 0 0 0 0 0 0 0 0 0 SV034 SSF3 0 0 0 0 0 0 0 0 0 SV035 SSF4 0 0 0 0 0 0 0 0 0 SV036 PTYP - - - - - - - - - SV037 JL 0 0 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 0 0 SV046 0 0 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 0 0 SV051 0 0 0 0 0 0 0 0 0 SV052 0 0 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 0 0 SV054 0 0 0 0 0 0 0 0 0 SV055 0 0 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 0 0 SV065 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 139

(e) HC-MF series

Motor HC-MF 053

HC-MF 13

HC-MF 23

HC-MF 43

HC-MF 73

Drive unit capacity 01 01 03 04 07

SV001 PC1 - - - - - SV002 PC2 - - - - - SV003 PGN1 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 SV005 VGN1 6 6 6 6 8 SV006 0 0 0 0 0 SV007 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 SV009 IQA 4096 4096 4096 4096 4096 SV010 IDA 4096 4096 4096 4096 4096 SV011 IQG 200 300 400 300 300 SV012 IDG 200 300 400 300 300 SV013 ILMT 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 SV015 FFC 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 SV018 PIT - - - - - SV019 RNG1 8 8 8 8 8 SV020 RNG2 8 8 8 8 8 SV021 OLT 60 60 60 60 60 SV022 OLL 150 150 150 150 150 SV023 OD1 - - - - - SV024 INP 50 50 50 50 50 SV025 MTYP 229C 229D 229E 2290 2291 SV026 OD2 - - - - - SV027 SSF1 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 SV029 0 0 0 0 0 SV030 IVC 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 SV032 TOF 0 0 0 0 0

7. Servo Parameters 7.1 MDS-B-SVJ2

II - 140

Motor HC-MF 053

HC-MF 13

HC-MF 23

HC-MF 43

HC-MF 73

Drive unit capacity 01 01 03 04 07

SV033 SSF2 0 0 0 0 0 SV034 SSF3 0 0 0 0 0 SV035 SSF4 0 0 0 0 0 SV036 PTYP - - - - - SV037 JL 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 SV046 0 0 0 0 0 SV047 EC 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 SV051 0 0 0 0 0 SV052 0 0 0 0 0 SV053 OD3 0 0 0 0 0 SV054 0 0 0 0 0 SV055 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 SV065 0 0 0 0 0

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 141

7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

(1) Details for servo parameters

For parameters marked with a (PR) in the table, turn the NC power OFF after setting. After the power is turned ON again, the parameter is validated.

! CAUTION

! In the explanation on bits, set all bits not used, including blank bits, to 0.

No. Items Details Setting range

2201 (PR)

SV001 PC1

Motor side gear ratio

1 to 32767

2202 (PR)

SV002 PC2

Machine side gear ratio

Set the motor side and machine side gear ratio. For the rotary axis, set the total deceleration (acceleration) ratio. Even if the gear ratio is within the setting range, the electronic gears may overflow and cause an alarm.

1 to 32767

2203 SV003 PGN1

Position loop gain 1

Set the position loop gain. The standard setting is "33 ". The higher the setting value is, the more precisely the command can be followed and the shorter the positioning time gets, however, note that a bigger shock is applied to the machine during acceleration/deceleration. When using the SHG control, also set SV004 (PGN2) and SV057 (SHGC). (If "201 " or bigger is set, the SHG control cannot be used.)

1 to 200 (In case of MDS-B-Vx4, 1 to 400) (rad/s)

2204 SV004 PGN2

Position loop gain 2

When using the SHG control, also set SV003 (PGN1) and SV057 (SHGC). When not using the SHG control, set to 0.

0 to 999 (rad/s)

2205 SV005 VGN1

Speed loop gain 1

Set the speed loop gain. Set this according to the load inertia size. The higher the setting value is, the more accurate the control will be, however, vibration tends to occur. If vibration occurs, adjust by lowering by 20 to 30%. The value should be determined to be 70 to 80% of the value at the time when the vibration stops.

1 to 999

2206 SV006 VGN2

Speed loop gain 2

If the noise is bothersome at high speed during rapid traverse, etc, lower the speed loop gain. As in the right figure, set the speed loop gain of the speed 1.2 times as fast as the motors rated speed, and use this with SV029 (VCS). When not using, set to 0.

VGN1 VGN2

VCS VLMT 0

(Rated speed*1.2)

-1000 to 1000

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 142

No. Items Details Setting range

Set this when the limit cycle occurs in the full-closed loop, or overshooting occurs in positioning. Select the control method with SV027 (SSF1)/bit1, 0 (vcnt). Normally, use "Changeover type 2 ". When you set this parameter, make sure to set the torque offset (SV032 (TOF)). When not using, set to "0 ". No changeover When SV027 (SSF1)/ bit1, 0 (vcnt)=00 The delay compensation control is always valid. Changeover type 1 When SV027 (SSF1)/ bit1, 0 (vcnt)=01 The delay compensation control works when the command from the NC is "0 ". Overshooting that occurs during pulse feeding can be suppressed.

2207 SV007 VIL

Speed loop delay compensation

Changeover type 2 When SV027 (SSF1)/ bit1, 0 (vcnt)=10 The delay compensation control works when the command from the NC is "0" and the position droop is "0". Overshooting or the limit cycle that occurs during pulse feeding or positioning can be suppressed.

0 to 32767

2208 SV008 VIA

Speed loop lead compensation

Set the gain of the speed loop integration control. The standard setting is "1364". During the SHG control, the standard setting is "1900". Adjust the value by increasing/decreasing it by about 100 at a time. Raise this value to improve contour tracking precision in high-speed cutting. Lower this value when the position droop vibrates (10 to 20Hz).

1 to 9999

2209 SV009 IQA

Current loop q axis lead compensation

2210 SV010 IDA

Current loop d axis lead compensation

1 to 20480

2211 SV011 IQG

Current loop q axis gain

2212 SV012 IDG

Current loop d axis gain

Set the gain of current loop. As this setting is determined by the motor's electrical characteristics, the setting is fixed for each type of motor. Set the standard values for all the parameters depending on each motor type.

1 to 4096 (In case of MDS-B-Vx4, 1 to 8192)

2213 SV013 ILMT

Current limit value

Set the normal current (torque) limit value. (Limit values for both + and - direction.) When the value is "500" (a standard setting), the maximum torque is determined by the specification of the motor.

0 to 999 (Stall [rated] current %)

2214 SV014 ILMTsp

Current limit value in special control

Set the current (torque) limit value in a special control (initial absolute position setting, stopper control, etc). (Limit values for both of the + and - directions.) Set to "500" when not using.

0 to 999 (Stall [rated] current %)

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 143

No. Items Details Setting range

2215 SV015 FFC

Acceleration rate feed forward gain

When a relative error in the synchronous control is large, apply this parameter to the axis that is delaying. The standard setting value is "0". For the SHG control, set to "100". To adjust a relative error in acceleration/deceleration, increase the value by 50 to 100 at a time.

0 to 999(%)

Set this when the protrusion (that occurs due to the non-sensitive band by friction, torsion, backlash, etc) at quadrant change is too large. This compensates the torque at quadrant change. This is valid only when the lost motion compensation (SV027 (SSF1/lmc)) is selected.

Type 1: When SV027 (SSF1)/ bit9, 8 (lmc)=01 Set the compensation amount based on the motor torque before the quadrant change. The standard setting is "100". Setting to "0" means the compensation amount is zero. Normally, use Type 2.

-1 to 200 (%)

Type 2: When SV027 (SSF1)/ bit9, 8 (lmc)=10 Set the compensation amount based on the stall (rated) current of the motor. The standard setting is double of the friction torque. Setting to "0" means the compensation amount is zero.

-1 to 100 (Stall [rated] current %)

2216 SV016 LMC1

Lost motion compensa- tion 1

When you wish different compensation amount depending on the direction When SV041 (LMC2) is "0", compensate with the value of SV016 (LMC1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV041 (LMC2). (SV016: + direction, SV041: - direction. However, the directions may be opposite depending on other settings.) When "-1" is set, the compensation wont be performed in the direction of the command.

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 144

No. Items Details Setting range

2217 (PR)

SV017 SPEC

Servo specification selection

F E D C B A 9 8 spm drvall drvup mpt3 mp

7 6 5 4 3 2 1 0 abs vdir fdir vfb seqh dfbx fdir2

bit Meaning when "0" is set Meaning when "1" is set

0 fdir2 Speed feedback forward polarity

Speed feedback reverse polarity

1 dfbx Dual feedback control stop Dual feedback control start

2 seqh READY/Servo ON time normal READY/Servo ON time high speed

3 vfb Speed feedback filter stop Speed feedback filter stop (2250Hz)

4 fdir Position feedback forward polarity

Position feedback reverse polarity

5 vdir Standard setting HA motor (4 pole motor)

Detector installation position 90 degrees (B, D)

6 7 abs Incremental control Absolute position control 8 mp MP scale 360P (2mm pitch) MP scale 720P (1mm pitch)

9 mpt3 MP scale ABS detection type 1, 2 MP scale ABS detection type 3

A drvup

Standard setting Possible to connect a drive unit whose capacity is 1 rank higher/lower than the standard one.

B drvall

Setting for normal use Possible to connect a drive unit with any capacity.

C D E F

spm

0 1 2 to F

: Setting for normal use : When using the S type drive unit (Only in the case of MDS-C1-Vx)

: Setting prohibited (Note 1) Set to "0" for bits with no particular description. (Note 2) bit3 (vfb) is only for MDS-C1-Vx.

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 145

No. Items Details Setting range

2218 (PR)

SV018 PIT

Ball screw pitch

Set the ball screw pitch. Set to 360 for the rotary axis. 1 to 32767 (mm/rev)

2219 (PR)

SV019 RNG1

Position detector resolution

In the case of the semi-closed loop control Set the same value as SV020 (RNG2). (Refer to the explanation of SV020.)

1 to 9999 (kp/rev)

In the case of the semi-closed loop control Set the same value as SV020 (RNG2). (Refer to the explanation of SV020.)

1 to 9999 (kp/pit)

Detector model name Resolution SV019 setting OHE25K-ET, OHA25K-ET 100,000(p/rev) 100 OSE104-ET, OSA104-ET 100,000(p/rev) 100 OSE105-ET, OSA105-ET 1,000,000(p/rev) 1000 RCN723 (Heidenhain) 8,000,000(p/rev) 8000 Relative position detection scale

Refer to specification manual for each detector

PIT/Resolution (m)

AT41 (Mitsutoyo) 1 (m/p) The same as SV018 (PIT)

FME type, FLE type (Futaba)

Refer to specification manual for each detector

PIT/Resolution (m)

MP type (Mitsubishi Heavy Industries)

Refer to specification manual for each detector

PIT/Resolution (m)

AT342 (Mitsutoyo) 0.5 (m/p) Twice as big as SV018 (PIT)

AT343 (Mitsutoyo) 0.05 (m/p) 20 times as big as SV018 (PIT)

LC191M (Heidenhain) Refer to specification manual for each detector

PIT/Resolution (m)

LC491M (Heidenhain) Refer to specification manual for each detector

PIT/Resolution (m)

Set the number of pulses per one revolution of the motor end detector. Detector model name SV020 setting OSE104, OSA104 100 OSE105, OSA105 1000

2220 (PR)

SV020 RNG2

Speed detector resolution

1 to 9999 (kp/rev)

2221 SV021 OLT

Overload detection time constant

Set the detection time constant of Overload 1 (Alarm 50). Set to "60" as a standard. (For machine tool builder adjustment.)

1 to 999 (s)

2222 SV022 OLL

Overload detection level

Set the current detection level of Overload 1 (Alarm 50) in respect to the stall (rated) current. Set to "150" as a standard. (For machine tool builder adjustment.)

110 to 500 (Stall [rated] current %)

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 146

No. Items Details Setting range

Set the excessive error detection width when servo ON.

Rapid traverse rate (mm/min)

OD1=OD2= 60*PGN1

/2 (mm)

2223 SV023 OD1

Excessive error detection width during servo ON

When "0" is set, the excessive error detection will not be performed.

0 to 32767 (mm)

2224 SV024 INP

In-position detection width

Set the in-position detection width. Set the accuracy required for the machine. The lower the setting is, the higher the positioning accuracy gets, however, the cycle time (setting time) becomes longer. The standard setting is 50.

0 to 32767 (m)

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 147

No. Items Details Setting range

2225 (PR)

SV025 MTYP

Motor /Detector type

F E D C B A 9 8 pen ent

7 6 5 4 3 2 1 0 mtyp

bit Explanation

0 Set the motor type. 1 Set this along with SV017 (SPEC)/spm. 2 1) When SV017/spm=0 (Normal drive unit)

3 Set- ting 0x 1x 2x 3x 4x 5x 6x 7x

4 x0 HA40N HA50L HA53L 5 x1 HA80N HA100L HA103L 6 x2 HA100N HA200L HA203L 7 x3 HA200N HA300L HA303L x4 HA300N HA500L HA503L

mtyp

x5 HA700N x6 HA900N x7 HA-LH11K2 x8 HA-LH15K2 x9 xA HA150L HA153L xB xC xD HA-LF15K2 xE xF

Set- ting 8x 9x Ax Bx Cx Dx Ex Fx

x0 HA43N HC52 HC53 x1 HA83N HC102 HC103 HC103R x2 HA103N HC152 HC153 HC153R x3 HA203N HC202 HC203 HC203R x4 HA303N HC352 HC353 HC353R x5 HA703N HC452 HC453 HC503R x6 HC702 HC703 x7 HC902 x8 x9 xA HA93N xB xC HA053N xD HA13N xE HA23N xF HA33N

(Continued to the next page)

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 148

No. Items Details Setting range

(Continued from the previous page) bit Explanation

2) When SV017/spm=1 (S type drive unit)

Set- ting 8x 9x Ax Bx Cx Dx Ex Fx

x0 x1 x2 x3 x4 HC353 x5 HC452 HC453 x6 HC702 x7 x8 x9 xA xB xC xD xE xF 8 Set the detector type. 9 A

Set the position detector type for "pen", and the speed detector type for "ent". In the case of the semi-closed loop control, set the same value for "pen" and "ent".

B

ent

pen setting ent setting Detector model name

C 0 0 OSE104 D 1 1 OSA104 E 2 2 OSE105, OSA105 F

pen

3 3 4 Setting

impossible OHE25K-ET, OSE104-ET

5 Setting impossible

OHA25K-ET, OSA104-ET

6 Setting impossible

OSE105-ET, OSA105-ET, RCN723 (Heidenhain)

7 Setting impossible

8 Setting impossible

Relative position detection scale, MP type (Mitsubishi Heavy Industries)

9 Setting impossible

AT41 (Mitsutoyo), FME type, FLE type (Futaba)

A Setting impossible

AT342,AT343 (Mitsutoyo), LC191M/491M (Heidenhain), MDS-B-HR

B Setting impossible

C C (Current

synchroni- zation)

The setting of the slave axis in the speed/current synchronization control. When the master axis is the semi-closed control.

D E (Current

synchroni- zation)

The setting of the slave axis in the speed/current synchronization control. When the master axis is the full-closed control. (Current synchronization control is only for MDS-C2-Vx.)

E Setting impossible

F Setting impossible

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 149

No. Items Details Setting range

2226 SV026 OD2

Excessive error detection width during servo OFF

Set the excessive error detection width when servo ON. For the standard setting, refer to the explanation of SV023 (OD1). When "0" is set, the excessive error detection will not be performed.

0 to 32767 (mm)

2227 SV027 SSF1

Servo function selection 1

F E D C B A 9 8 aflt zrn2 afse ovs lmc 7 6 5 4 3 2 1 0

omr zrn3 vfct upc vcnt bit Meaning when "0" is set Meaning when "1" is set

0 Set the execution changeover type of the speed loop delay compensation.

1 vcnt

00: Delay compensation changeover invalid 01: Delay compensation changeover type 1 10: Delay compensation type 2 11: Setting prohibited

2 upc Start torque compensation invalid

Start torque compensation valid

3

4 Set the number of compensation pulses of the jitter compensation.

5 vfct

00: Jitter compensation invalid 01: Jitter compensation 1 pulse 10: Jitter compensation 2 pulses 11: Jitter compensation 3 pulses

6 zrn3 ABS scale: Set to "1" in using AT342, AT343, LC191M/491M.

7 omr Machine end compensation invalid

Machine end compensation valid

8 Set the compensation amount with SV016 (LMC1) and SV041 (LMC2).

9 lmc

00: Lost motion compensation stop 01: Lost motion compensation type 1 10: Overshooting compensation type 2 11: Setting prohibited

A Set the compensation amount with SV031 (OVS1) and SV042 (OVS2).

B ovs

00: Overshooting compensation stop 01: Overshooting compensation type 1 10: Overshooting compensation type 2 11: Overshooting compensation type 3

C D afse 00: Adoptive filter sensitivity standard

11: Adoptive filter sensitivity increase (Set 2bits at a time) E zrn2 Set to "1". F aflt Adoptive filter stop Adoptive filter start

(Note) Set to "0" for bits with no particular description.

2228 SV028 Not used. Set to "0". 0 2229 SV029 Speed at the

change of speed loop gain

If the noise is bothersome at high speed during rapid traverse, etc, lower the speed loop gain. Set the speed at which the speed loop gain changes, and use this with SV006 (VGN2). (Refer to SV006.) When not using, set to "0".

0 to 9999 (r/min)

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 150

No. Items Details Setting range

The higher order 8bits and lower order 8bits are used for different functions. The setting value of SV030 = (Icx*256) + IVC

0 to 32767

SV030 IVC (Low order)

Voltage dead time compensa- tion

When 100% is set, the voltage equivalent to the logical non-energized time will be compensated. When "0" is set, a 100% compensation will be performed. Adjust in increments of 10% from the default value 100%. If increased too much, vibration or vibration noise may be generated.

0 to 255 (%)

2230

SV030 Icx (High order)

Current bias 1 Set to "0" as a standard. Use this in combination with SV040 and the high order 8bits of SV045.

0 to 127

Set this if overshooting occurs during positioning. This compensates the motor torque during positioning. This is valid only when the overshooting compensation SV027 (SSF1/ovs) is selected. Type 1: When SV027 (SSF1)/ bitB, A (ovs)=01 Set the compensation amount based on the motors stall current. This compensates overshooting that occurs during pulse feeding. Normally, use Type 2. Type 2: When SV027 (SSF1)/ bitB, A (ovs)=10 Set the compensation amount based on the motors stall current. Increase by 1% and determine the amount that overshooting doesnt occur. In Type 2, compensation during the feed forward control during circular cutting wont be performed. Type 3: When SV027 (SSF1)/ bitB, A (ovs)=11 Use this to perform the overshooting compensation during circular cutting or the feed forward control. The setting method is the same in Type 2.

2231 SV031 OVS1

Overshooting compensation 1

When you wish different compensation amount depending on the direction When SV042 (OVS2) is "0", compensate with the value of SV031 (OVS1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV042 (OVS2). (SV031: + direction, SV042: - direction. However, the directions may be opposite depending on other settings.) When "-1" is set, the compensation won't be performed in the direction of the command.

-1 to 100 (Stall [rated] current %)

2232 SV032 TOF

Torque offset Set the unbalance torque of vertical axis and inclined axis.

-100 to 100 (Stall [rated] current %)

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 151

No. Items Details Setting range

2233 SV033 SSF2

Servo function selection 2

F E D C B A 9 8 dos hvx svx

7 6 5 4 3 2 1 0 nfd2 nf3 nfd1 zck

bit Meaning when "0" is set Meaning when "1" is set 0 zck Z phase check valid (Alarm 42) Z phase check invalid 1 Set the filter depth for Notch filter 1 (SV038). 2 Value 000 001 010 011 100 101 110 111

3 nfd1

Depth (dB)

Infntly deep -18.1 -12.0 -8.5 -6.0 -4.1 -2.5 -1.2

Deep Shallow 4 nf3 Notch filter 3 stop Notch filter 3 start (1125Hz) 5 Set the operation frequency of Notch filter 2 (SV046). 6 Value 000 001 010 011 100 101 110 111

7 nfd2

Depth (dB)

Infntly deep -18.1 -12.0 -8.5 -6.0 -4.1 -2.5 -1.2

Deep Shallow

8 svx Set the performance mode of the servo control. (Only for MDS-C1-Vx)

9 hvx

00: By current loop gain 01: MDS-B-Vx compatible mode selected 10: High gain mode selected 11: High gain mode selected

A B C Digital signal output selection

D 0 : MP scale absolute position detection, offset demand signal output

E 1 : Specified speed signal output F

dos

2 to F : Setting prohibited (Note) Set to "0" for bits with no particular description.

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 152

No. Items Details Setting range

2234 SV034 SSF3

Servo function selection 3

F E D C B A 9 8 ovsn

7 6 5 4 3 2 1 0 os2 zeg mohn has2 has1

bit Meaning when "0" is set Meaning when "1" is set

0 has1 Setting for normal use (Except for HC)

HAS control 1 valid (HC: High acceleration rate support)

1 has2 Setting for normal use (Except for HC)

HAS control 2 valid (HC: Overshooting support)

2 moh n

MDS-B-HR motor thermal valid

MDS-B-HR motor thermal ignored

3 4 5 zeg

Z phase normal edge detection (Setting for normal use)

Z phase reverse edge detection (Valid only when SV027/bit6=1)

6 os2 Setting for normal use Overspeed detection level changeover

7 8 9 A B C D E

F

ovsn

Set the non-sensitive band of the overshooting compensation type 3 in increments of 2m at a time. In the feed forward control, the non-sensitive band of the model position droop is set, and overshooting of the model is ignored. Set the same value as the standard SV040.

(Note) Set to "0" for bits with no particular description.

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 153

No. Items Details Setting range 2235 SV035

SSF4 Servo function selection 4

F E D C B A 9 8 clt clG1 cl2n clet cltq 7 6 5 4 3 2 1 0

ckab iup tdt bit Meaning when "0" is set Meaning when "1" is set

0 1 2 3 4 5

tdt

Td creation time setting Set to 0. (For machine tool builder adjustment)

6 iup Set to "1" when using any of motors from HC152 to HC702 and from HC153 to HC453.

7 ckab Setting for normal use No signal 2 (Alarm 21) special detection

8 Set the retracting torque for collision detection in respect to the maximum torque of the motor.

9 cltq

00: 100% 01: 90% 10: 80% (Standard) 11: 70% A clet Setting for normal use

The disturbance torque peak of the latest two seconds is displayed in MPOS of the servo monitor screen.

B cl2n Collision detection method 2 valid

Collision detection method 2 invalid

C D

E clG1

Collision detection method 1 Set the collision detection level during cutting feed (G1). The G1 collision detection level=SV060*clG1. When clG1=0, the collision detection method 1 during cutting feed won't function.

F clt Setting for normal use

The guide value of the SV059 setting value is displayed in MPOS of the servo monitor screen.

(Note) bit7 (ckab) is only for MDS-C1-Vx.

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 154

No. Items Details Setting range 2236 (PR)

SV036 PTYP

Power supply type

F E D C B A 9 8 amp rtyp

7 6 5 4 3 2 1 0 ptyp

bit Explanation

0 1 2

When the CN4 connector of the drive unit and the power supply are connected, setting below is necessary. To validate the external emergency stop function, add 40h.

3 Set- ting 0x 1x 2x 3x 4x 5x 6x 7x 8x

4 x0 Not used CV-300

5 x1 CV-110 CR-10 6 x2 CV-220 CR-15 7

ptyp

x3 CR-22 x4 CV-37 CR-37 x5 CV-150 CV-450CV-550 x6 CV-55 CV-260 CR-55 x7 CV-370 x8 CV-75 CR-75 x9 CV-185 CR-90

8 Set the regenerative resistor type when MDS-A-CR is used.

9 Set- ting

Regenerative resistor model name

Resistance value Capacity

A 0 MDS-C1-CV (Setting when using power supply regeneration)

B

rtyp

1 GZG200W260HMJ 26 80W 2 GZG300W130HMJ2 26 150W 3 MR-RB30 13 300W 4 MR-RB50 13 500W 5 GZG200W200HMJ3 6.7 350W 6 GZG300W200HMJ3 6.7 500W 7 R-UNIT-1 30 700W 8 R-UNIT-2 15 700W 9 R-UNIT-3 15 2100W A to F No setting

C D E F

amp

Always set to "0".

Set "the motor inertia + motor axis conversion load inertia" in respect to the motor inertia.

Jl+Jm SV037 (JL) =

Jm *100

Jm: Motor inertia

2237 SV037 JL

Load inertia scale

Jl: Motor axis conversion load inertia

0 to 5000 (%)

2238 SV038 FHz1

Notch filter frequency 1

Set the vibration frequency to suppress if machine vibration occurs. (Valid at 36 or more) When not using, set to "0".

0 to 9000 (Hz)

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 155

No. Items Details Setting range

2239 SV039 LMCD

Lost motion compensation timing

Set this when the lost motion compensation timing doest not match. Adjust by increasing the value by 10 at a time.

0 to 2000 (ms)

The higher order 8bits and lower order 8bits are used for different functions. "Setting value of SV040" = (Icy*256) + LMCT

0 to 32767

SV040 LMCT (Low order)

Lost motion compensation non-sensitive band

Set the non-sensitive band of the lost motion compensation in the feed forward control. When "0" is set, the actual value that is set is 2m. Adjust by increasing by 1m at a time.

0 to 100 (m)

2240

SV040 Icy (High order)

Current bias 2 Normally, set to "40" if you use HC202 to HC902, HC203 to HC703. Use this in combination with SV030 and the high order 8bits of SV045.

0 to 127

2241 SV041 LMC2

Lost motion compensation 2

Set this with SV016 (LMC1) only when you wish to set the lost motion compensation amount to be different depending on the command directions. Set to "0" as a standard.

-1 to 200 (Stall [rated] current %)

2242 SV042 OVS2

Overshooting compensation 2

Set this with SV031 (OVS1) only when you wish to set the overshooting compensation amount to be different depending on the command directions. Set to "0" as a standard.

-1 to 100 (Stall [rated] current %)

2243 SV043 OBS1

Disturbance observer filter frequency

Set the disturbance observer filter band. Set to "100" as a standard. To use the disturbance observer, also set SV037 (JL) and SV044 (OBS2). When not using, set to "0".

0 to 1000 (rad/s)

2244 SV044 OBS2

Disturbance observer gain

Set the disturbance observer gain. The standard setting is "100" to "300". To use the disturbance observer, also set SV037 (JL) and SV043 (OBS1). When not using, set to "0".

0 to 500 (%)

The higher order 8bits and lower order 8bits are used for different functions. "Setting value of SV045" = (Icy*256) + LMCT

0 to 32767

SV045 TRUB (Low order)

Frictional torque

When you use the collision detection function, set the frictional torque.

0 to 100 (Stall [rated] current %)

2245

SV045 Ib1 (High order)

Current bias 3 Set to "0" as a standard. Use this in combination with SV030 and the high order 8bits of SV040.

0 to 127

2246 SV046 FHz2

Notch filter frequency 2

Set the vibration frequency to suppress if machine vibration occurs. (Valid at 36 or more) When not using, set to "0".

0 to 9000 (Hz)

2247 SV047 EC

Inductive voltage compensation gain

Set the inductive voltage compensation gain. Set to "100" as a standard. If the current FB peak exceeds the current command peak, lower the gain.

0 to 200 (%)

2248 SV048 EMGrt

Vertical axis drop prevention time

Input a length of time to prevent the vertical axis from dropping by delaying Ready OFF until the brake works when the emergency stop occurs. Increase the setting by 100ms at a time and set the value where the axis does not drop.

0 to 20000 (ms)

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 156

No. Items Details Setting range

2249 SV049 PGN1sp

Position loop gain 1 in spindle synchronous control

Set the position loop gain during the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). Set the same value as the value of the spindle parameter, position loop gain in synchronous control. When performing the SHG control, set this with SV050 (PGN2sp) and SV058 (SHGCsp).

1 to 200 (rad/s)

2250 PGN2sp Position loop gain 2 in spindle synchronous control

Set this with SV049 (PGN1sp) and SV058 (SHGCsp) if you wish to perform the SHG control in the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to "0".

0 to 999 (rad/s)

2251 SV051 DFBT

Dual feed back control time constant

Set the control time constant in dual feed back. When "0" is set, the actual value that is set is 1ms. The higher the time constant is, the closer it gets to the semi-closed control, so the limit of the position loop gain is raised.

0 to 9999 (ms)

2252 SV052 DFBN

Dual feedback control non-sensitive band

Set the non-sensitive band in the dual feedback control. Set to "0" as a standard.

0 to 9999 (m)

2253 SV053 OD3

Excessive error detection width in special control

Set the excessive error detection width when servo ON in a special control (initial absolute position setting, stopper control, etc.). If "0" is set, excessive error detection won't be performed when servo ON during a special control.

0 to 32767 (mm)

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 157

No. Items Details Setting range

When SV035 (SSF4)/ bitF (ckab)=0 SV054 ORE

Overrun detection width in closed loop control

Set the overrun detection width in the full-closed loop control. If the gap between the motor end detector and the linear scale (machine end detector) exceeds the value set by this parameter, it is judged to be overrun and Alarm 43 will be detected. When "-1" is set, the alarm detection won't be performed. When "0" is set, overrun is detected with a 2mm width.

-1 to 32767 (mm)

When SV035 (SSF4)/ bitF (ckab)=1 (Note) This applies to only MDS-C1-Vx.

The higher order 8bits and lower order 8bits are used for different functions. "Setting value of SV054" =(NSE*256)+ORE

0 to 32767

SV054 ORE (Low order)

Overrun detection- width in closed loop control

Set the overrun detection width in the full-closed loop control. If the gap between the motor end detector and the linear scale (machine end detector) exceeds the value set by this parameter, it is judged to be overrun and Alarm 43 will be detected. When "255" is set, the alarm detection won't be performed. When "0" is set, overrun is detected with a 2mm width.

0 to 255 (mm)

2254

SV054 NSE (High order)

Special detection width for No signal 2

When SV035 (SSF4)/ bitF (ckab) =1, this setting is valid. Set the special detection width for No signal 2 (Alarm 21). When "0" is set, overrun is detected with a 15m width.

0 to 127 (m)

2255 SV055 EMGx

Max. gate off delay time after emergency stop

Set a length of time from the point when the emergency stop is input to the point when READY OFF is compulsorily executed. Normally, set the same value as the absolute value of SV056. In preventing the vertical axis from dropping, the gate off is delayed for the length of time set by SV048 if SV055s value is smaller than that of SV048.

0 to 20000 (ms)

2256 SV056 EMGt

Deceleration time constant at emergency stop

In the vertical axis drop prevention time control, set the time constant used for the deceleration control at emergency stop. Set a length of time that takes from rapid traverse rate (rapid) to stopping. Normally, set the same value as the rapid traverse acceleration/deceleration time constant. When executing the synchronous operation, put the minus sign to the settings of both of the master axis and slave axis.

-20000 to 20000 (ms)

2257 SV057 SHGC

SHG control gain

When performing the SHG control, set this with S003 (PGN1) and SV004 (PGN2). When not performing the SHG control, set to "0".

0 to 1200 (rad/s)

2258 SV058 SHGCsp

SHG control gain in spindle synchronous control

Set this with SV049 (PGN1sp) and SV050 (PGN2sp) if you wish to perform the SHG control in the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to "0".

0 to 1200 (rad/s)

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 158

No. Items Details Setting range

2259 SV059 TCNV

Collision detection torque estimating gain

Set the torque estimating gain when using the collision detection function. After setting as SV035/bitF(clt)=1 and performing acceleration/deceleration, set the value displayed in MPOS of the NC servo monitor screen. Set to "0" when not using the collision detection function.

-32768 to 32767

2260 SV060 TLMT

Collision detection level

When using the collision detection function, set the collision detection level during the G0 feeding. If "0" is set, none of the collision detection function will work.

0 to 999 (Stall [rated] current %)

2261 SV061 DA1NO

D/A output channel 1 data No.

2262 SV062 DA2NO

D/A output channel 2 data No.

Input the data number you wish to output to D/A output channel. In the case of MDS-C1-V2, set the axis on the side to which the data will not be output to "-1".

-1 to 127

2263 SV063 DA1MPY

D/A output channel 1 output scale

2264 SV064 DA2MPY

D/A output channel 2 output scale

Set the scale with a 1/256 unit. When "0" is set, output is done with the standard output unit.

-32768 to 32767 (Unit: 1/256)

Set the spring constant of the tool end compensation. In the semi-closed loop control, the tool end compensation amount is calculated with the following equation.

F (mm/min)2*SV065 Compensation amount=

R (mm)*109 (m)

F: Commanded speed R: Radius

2265 SV065 TLC

Tool end compensation spring constant

When not using, set to "0".

-32768 to 32767

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 159

(2) Initial setting value

(a) HC**/HC**R series

Motor HC 52

HC 102

HC 152

HC 202

HC 352

HC 452

HC 702

HC 902

Drive unit capacity 05 10 20 20 35 45s 45 70s 70 90

SV001 PC1 - - - - - - - - - - SV002 PC2 - - - - - - - - - - SV003 PGN1 47 47 47 47 47 47 47 47 47 47 SV004 PGN2 0 0 0 0 0 0 0 0 0 0 SV005 VGN1 200 200 200 200 200 200 200 200 200 200 SV006 VGN2 0 0 0 0 0 0 0 0 0 0 SV007 VIL 0 0 0 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 4096 4096 4096 4096 4096 4096 4096 4096 4096 4096 SV010 IDA 4096 4096 4096 4096 4096 4096 4096 4096 4096 4096 SV011 IQG 768 768 768 768 768 768 768 768 768 768 SV012 IDG 768 768 768 768 768 768 768 768 768 768 SV013 ILMT 500 500 500 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 1000 0000 1000 0000 0000 SV018 PIT - - - - - - - - - - SV019 RNG1 - - - - - - - - - - SV020 RNG2 - - - - - - - - - - SV021 OLT 60 60 60 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 50 50 50 50 SV025 MTYP xxB0 xxB1 xxB2 xxB3 xxB4 xx95 xxB5 xx96 xxB6 xxB7 SV026 OD2 6 6 6 6 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 0 0 0 SV029 VCS 0 0 0 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 160

Motor HC 52

HC 102

HC 152

HC 202

HC 352

HC 452

HC 702

HC 902

Drive unit capacity 05 10 20 20 35 45s 45 70s 70 90

SV033 SSF2 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV034 SSF3 0003 0003 0003 0003 0003 0003 0003 0003 0003 0003 SV035 SSF4 0000 0000 0040 0040 0040 0040 0040 0040 0040 0000 SV036 PTYP 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 10240 10240 10240 10240 10240 10240 10240 SV041 LMC2 0 0 0 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 0 0 0 SV046 FHz2 0 0 0 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 0 0 0 SV065 TLC 0 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 161

Motor HC 53

HC 103

HC 153

HC 203

HC 353

HC 453

HC 703

Drive unit capacity 05 10 20 35 45s 45 70s 70 90

SV001 PC1 - - - - - - - - - SV002 PC2 - - - - - - - - - SV003 PGN1 47 47 47 47 47 47 47 47 47 SV004 PGN2 0 0 0 0 0 0 0 0 0 SV005 VGN1 200 200 200 200 200 200 200 200 200 SV006 VGN2 0 0 0 0 0 0 0 0 0 SV007 VIL 0 0 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 4096 4096 4096 4096 4096 4096 4096 4096 4096 SV010 IDA 4096 4096 4096 4096 4096 4096 4096 4096 4096 SV011 IQG 768 768 768 768 768 768 768 768 768 SV012 IDG 768 768 768 768 768 768 768 768 768 SV013 ILMT 500 500 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 1000 0000 1000 0000 0000 SV018 PIT - - - - - - - - - SV019 RNG1 - - - - - - - - - SV020 RNG2 - - - - - - - - - SV021 OLT 60 60 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 50 50 50 SV025 MTYP xxC0 xxC1 xxC2 xxC3 xxA4 xxC4 xxA5 xxC5 xxC6 SV026 OD2 6 6 6 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 0 0 SV029 VCS 0 0 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 162

Motor HC 53

HC 103

HC 153

HC 203

HC 353

HC 453

HC 703

Drive unit capacity 05 10 20 35 45s 45 70s 70 90

SV033 SSF2 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV034 SSF3 0003 0003 0003 0003 0003 0003 0003 0003 0003 SV035 SSF4 0000 0000 0040 0040 0040 0040 0040 0040 0000 SV036 PTYP 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 10240 10240 10240 10240 10240 10240 SV041 LMC2 0 0 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 0 0 SV046 FHz2 0 0 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 0 0 SV065 TLC 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 163

Motor HC 103R

HC 153R

HC 203R

HC 353R

Drive unit capacity 10 10 20 35

SV001 PC1 - - - - SV002 PC2 - - - - SV003 PGN1 33 33 33 33 SV004 PGN2 0 0 0 0 SV005 VGN1 15 15 20 40 SV006 VGN2 0 0 0 0 SV007 VIL 0 0 0 0 SV008 VIA 1364 1364 1364 1364 SV009 IQA 4096 4096 4096 4096 SV010 IDA 4096 4096 4096 4096 SV011 IQG 256 256 256 256 SV012 IDG 512 512 512 512 SV013 ILMT 500 500 500 500 SV014 ILMTsp 500 500 500 500 SV015 FFC 0 0 0 0 SV016 LMC1 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 SV018 PIT - - - - SV019 RNG1 - - - - SV020 RNG2 - - - - SV021 OLT 60 60 60 60 SV022 OLL 150 150 150 150 SV023 OD1 6 6 6 6 SV024 INP 50 50 50 50 SV025 MTYP xxE1 xxE2 xxE3 xxE4 SV026 OD2 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 SV028 0 0 0 0 SV029 VCS 0 0 0 0 SV030 IVC 0 0 0 0 SV031 OVS1 0 0 0 0 SV032 TOF 0 0 0 0

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 164

Motor HC 103R

HC 153R

HC 203R

HC 353R

Drive unit capacity 10 10 20 35

SV033 SSF2 0200 0200 0200 0200 SV034 SSF3 0000 0000 0000 0000 SV035 SSF4 0000 0000 0000 0000 SV036 PTYP 0000 0000 0000 0000 SV037 JL 0 0 0 0 SV038 FHz1 0 0 0 0 SV039 LMCD 0 0 0 0 SV040 LMCT 0 0 0 0 SV041 LMC2 0 0 0 0 SV042 OVS2 0 0 0 0 SV043 OBS1 0 0 0 0 SV044 OBS2 0 0 0 0 SV045 TRUB 0 0 0 0 SV046 FHz2 0 0 0 0 SV047 EC 100 100 100 100 SV048 EMGrt 0 0 0 0 SV049 PGN1sp 15 15 15 15 SV050 PGN2sp 0 0 0 0 SV051 DFBT 0 0 0 0 SV052 DFBN 0 0 0 0 SV053 OD3 0 0 0 0 SV054 ORE 0 0 0 0 SV055 EMGx 0 0 0 0 SV056 EMGt 0 0 0 0 SV057 SHGC 0 0 0 0 SV058 SHGCsp 0 0 0 0 SV059 TCNV 0 0 0 0 SV060 TLMT 0 0 0 0 SV061 DA1NO 0 0 0 0 SV062 DA2NO 0 0 0 0 SV063 DA1MPY 0 0 0 0 SV064 DA2MPY 0 0 0 0 SV065 TLC 0 0 0 0

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 165

(b) HA**N series

Motor HA 40N

HA 80N

HA 100N

HA 200N

HA 300N

HA 700N

HA 900N

Drive unit capacity 05 10 20 35 45 70 90

SV001 PC1 - - - - - - - SV002 PC2 - - - - - - - SV003 PGN1 33 33 33 33 33 25 25 SV004 PGN2 0 0 0 0 0 0 0 SV005 VGN1 150 150 150 150 150 250 250 SV006 VGN2 0 0 0 0 0 0 0 SV007 VIL 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 4096 4096 4096 4096 4096 4096 4096 SV010 IDA 4096 4096 4096 4096 4096 4096 4096 SV011 IQG 768 768 768 768 768 768 768 SV012 IDG 768 768 768 768 768 768 768 SV013 ILMT 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - SV019 RNG1 - - - - - - - SV020 RNG2 - - - - - - - SV021 OLT 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 50 SV025 MTYP xx00 xx01 xx02 xx03 xx04 xx05 xx06 SV026 OD2 6 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 SV029 VCS 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 166

Motor HA 40N

HA 80N

HA 100N

HA 200N

HA 300N

HA 700N

HA 900N

Drive unit capacity 05 10 20 35 45 70 90

SV033 SSF2 0000 0000 0000 0000 0000 0000 0000 SV034 SSF3 0000 0000 0000 0000 0000 0000 0000 SV035 SSF4 0000 0000 0000 0000 0000 0000 0000 SV036 PTYP 0000 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 SV046 FHz2 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 SV065 TLC 0 0 0 0 0 0 0

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 167

Motor HA 43N

HA 83N

HA 93N

HA 103N

HA 203N

HA 303N

HA 703N

HA 053N

HA 13N

HA 23N

HA 33N

Drive unit capacity 05 10 20 35 45 70 90 01 01 03 03

SV001 PC1 - - - - - - - - - - - SV002 PC2 - - - - - - - - - - - SV003 PGN1 33 33 33 33 33 33 25 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 0 0 0 0 0 SV005 VGN1 150 150 150 150 150 150 250 70 70 100 100 SV006 0 0 0 0 0 0 0 0 0 0 0 SV007 0 0 0 0 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 4096 4096 4096 4096 4096 4096 4096 4096 4096 4096 4096 SV010 IDA 4096 4096 4096 4096 4096 4096 4096 4096 4096 4096 4096 SV011 IQG 768 768 768 768 768 768 768 768 768 768 768 SV012 IDG 768 768 768 768 768 768 768 768 768 768 768 SV013 ILMT 500 500 500 500 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - - - - - SV019 RNG1 - - - - - - - - - - - SV020 RNG2 - - - - - - - - - - - SV021 OLT 60 60 60 60 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 50 50 50 50 50 SV025 MTYP xx80 xx81 xx8A xx82 xx83 xx84 xx85 xx8C xx8D xx8E xx8F SV026 OD2 6 6 6 6 6 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 0 0 0 0 SV029 0 0 0 0 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.2 MDS-C1-Vx High-gain (MDS-B-Vx4 Compatible)

II - 168

Motor HA 43N

HA 83N

HA 93N

HA 103N

HA 203N

HA 303N

HA 703N

HA 053N

HA 13N

HA 23N

HA 33N

Drive unit capacity 05 10 20 35 45 70 90 01 01 03 03

SV033 SSF2 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV034 SSF3 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV035 SSF4 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV036 PTYP 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 0 0 0 0 SV046 FHz2 0 0 0 0 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 0 0 0 0 SV065 TLC 0 0 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 169

7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

(1) Details for servo parameters

For parameters marked with a (PR) in the table, turn the NC power OFF after setting. After the power is turned ON again, the parameter is validated.

! CAUTION

! In the explanation on bits, set all bits not used, including blank bits, to "0".

No. Items Details Setting range

2201 (PR)

SV001 PC1

Motor side gear ratio

1 to 32767

2202 (PR)

SV002 PC2

Machine side gear ratio

Set the motor side and machine side gear ratio. For the rotary axis, set the total deceleration (acceleration) ratio. Even if the gear ratio is within the setting range, the electronic gears may overflow and cause an alarm.

1 to 32767

2203 SV003 PGN1

Position loop gain 1

Set the position loop gain. The standard setting is "33". The higher the setting value is, the more precisely the command can be followed and the shorter the positioning time gets, however, note that a bigger shock is applied to the machine during acceleration/deceleration. When using the SHG control, also set SV004 (PGN2) and SV057 (SHGC).

1 to 200 (rad/s)

2204 SV004 PGN2

Position loop gain 2

When using the SHG control, also set SV003 (PGN1) and SV057 (SHGC). When not using the SHG control, set to "0".

0 to 999 (rad/s)

2205 SV005 VGN1

Speed loop gain 1

Set the speed loop gain. Set this according to the load inertia size. The higher the setting value is, the more accurate the control will be, however, vibration tends to occur. If vibration occurs, adjust by lowering by 20 to 30%. The value should be determined to be 70 to 80% of the value at the time when the vibration stops.

1 to 999

2206 SV006 VGN2

Speed loop gain 2

If the noise is bothersome at high speed during rapid traverse, etc, lower the speed loop gain. As in the right figure, set the speed loop gain of the speed 1.2 times as fast as the motor's rated speed, and use this with SV029 (VCS). When not using, set to "0".

VGN1 VGN2

VCS VLMT 0

(Rated speed*1.2)

-1000 to 1000

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 170

No. Items Details Setting range

Set this when the limit cycle occurs in the full-closed loop, or overshooting occurs in positioning. Select the control method with SV027 (SSF1)/bit1, 0 (vcnt). Normally, use "Changeover type 2". When you set this parameter, make sure to set the torque offset (SV032 (TOF)). When not using, set to "0". No changeover When SV027 (SSF1)/ bit1, 0 (vcnt)=00 The delay compensation control is always valid. Changeover type 1 When SV027 (SSF1)/ bit1, 0 (vcnt)=01 The delay compensation control works when the command from the NC is "0". Overshooting that occurs during pulse feeding can be suppressed.

2207 SV007 VIL

Speed loop delay compensation

Changeover type 2 When SV027 (SSF1)/ bit1, 0 (vcnt)=10 The delay compensation control works when the command from the NC is "0" and the position droop is "0". Overshooting or the limit cycle that occurs during pulse feeding or positioning can be suppressed.

0 to 32767

2208 SV008 VIA

Speed loop lead compensation

Set the gain of the speed loop integration control. The standard setting is "1364". During the SHG control, the standard setting is "1900". Adjust the value by increasing/decreasing it by about 100 at a time. Raise this value to improve contour tracking precision in high-speed cutting. Lower this value when the position droop vibrates (10 to 20Hz).

1 to 9999

2209 SV009 IQA

Current loop q axis lead compensation

1 to 20480

2210 SV010 IDA

Current loop d axis lead compensation

1 to 20480

2211 SV011 IQG

Current loop q axis gain

1 to 2560

2212 SV012 IDG

Current loop d axis gain

Set the gain of current loop. As this setting is determined by the motor's electrical characteristics, the setting is fixed for each type of motor. Set the standard values for all the parameters depending on each motor type.

1 to 2560

2213 SV013 ILMT

Current limit value

Set the normal current (torque) limit value. (Limit values for both + and - direction.) When the value is "500" (a standard setting), the maximum torque is determined by the specification of the motor.

0 to 999 (Stall [rated] current %)

2214 SV014 ILMTsp

Current limit value in special control

Set the current (torque) limit value in a special control (initial absolute position setting, stopper control, etc). (Limit values for both of the + and - directions.) Set to "500" when not using.

0 to 999 (Stall [rated] current %)

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 171

No. Items Details Setting range

2215 SV015 FFC

Acceleration rate feed forward gain

When a relative error in the synchronous control is large, apply this parameter to the axis that is delaying. The standard setting value is "0". For the SHG control, set to "100". To adjust a relative error in acceleration/deceleration, increase the value by 50 to 100 at a time.

0 to 999 (%)

Set this when the protrusion (that occurs due to the non-sensitive band by friction, torsion, backlash, etc) at quadrant change is too large. This compensates the torque at quadrant change. This is valid only when the lost motion compensation (SV027 (SSF1/lmc)) is selected.

Type 1: When SV027 (SSF1)/ bit9, 8 (lmc)=01 Set the compensation amount based on the motor torque before the quadrant change. The standard setting is "100". Setting to "0" means the compensation amount is zero. Normally, use Type 2.

-1 to 200 (%)

Type 2: When SV027 (SSF1)/ bit9, 8 (lmc)=10 Set the compensation amount based on the stall (rated) current of the motor. The standard setting is double of the friction torque. Setting to "0" means the compensation amount is zero.

-1 to 100 (Stall [rated] current %)

2216 SV016 LMC1

Lost motion compensation 1

When you wish different compensation amount depending on the direction When SV041 (LMC2) is "0", compensate with the value of SV016 (LMC1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV041 (LMC2). (SV016: + direction, SV041: - direction. However, the directions may be opposite depending on other settings.) When "-1" is set, the compensation won't be performed in the direction of the command.

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 172

No. Items Details Setting range

2217 (PR)

SV017 SPEC

Servo specification selection

F E D C B A 9 8 mpt3 mp

7 6 5 4 3 2 1 0 abs vdir fdir spwv seqh dfbx fdir2

bit Meaning when "0" is set Meaning when "1" is set

0 fdir2 Speed feedback forward polarity

Speed feedback reverse polarity

1 dfbx Dual feedback control stop Dual feedback control start

2 seqh READY/Servo ON time normal READY/Servo ON time high speed

3 spwv Normal mode High gain servo synchronous mode

4 fdir Position feedback forward polarity

Position feedback reverse polarity

5

vdir Standard setting

HA motor (4 pole motor) Detector installation position 90 degrees (B, D)

6 7 abs Incremental control Absolute position control 8 mp MP scale 360P (2mm pitch) MP scale 720P (1mm pitch)

9 mpt3 MP scale ABS detection type 1, 2 MP scale ABS detection type 3

A B C D E F

(Note) Set to "0" for bits with no particular description. 2218 (PR)

SV018 PIT

Ball screw pitch

Set the ball screw pitch. Set to "360" for the rotary axis. 1 to 32767 (mm/rev)

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 173

No. Items Details Setting range

2219 (PR)

SV019 RNG1

Position detector resolution

In the case of the semi-closed loop control Set the same value as SV020 (RNG2). (Refer to the explanation of SV020.)

1 to 9999 (kp/rev)

In the case of the full-closed loop control Set the number of pulses per ball screw pitch.

1 to 9999 (kp/pit)

Detector model name Resolution SV019 setting OHE25K-ET, OHA25K-ET 100,000(p/rev) 100

OSE104-ET, OSA104-ET 100,000(p/rev) 100

OSE105-ET, OSA105-ET 1,000,000(p/rev) 1000

Relative position detection scale

Refer to specification manual for each detector

PIT/Resolution (m)

AT41 (Mitsutoyo) 1 (m/p) The same as SV018 (PIT)

FME type, FLE type (Futaba)

Refer to specification manual for each detector

PIT/Resolution (m)

MP type (Mitsubishi Heavy Industries)

Refer to specification manual for each detector

PIT/Resolution (m)

AT342 (Mitsutoyo) 0.5 (m/p) Twice as big as SV018 (PIT)

Set the number of pulses per one revolution of the motor end detector. Detector model name SV020 setting Equipped to HA053, HA13 (Only for

MDS-B-Vx) 10

OHE25K, OHA25K (Only for MDS-B-Vx) 100

OSE104, OSA104 100 OSE105, OSA105 1000

2220 (PR)

SV020 RNG2

Speed detector resolution

1 to 9999 (kp/rev)

2221 SV021 OLT

Overload detection time constant

Set the detection time constant of Overload 1 (Alarm 50). Set to "60" as a standard. (For machine tool builder adjustment.)

1 to 999 (s)

2222 SV022 OLL

Overload detection level

Set the current detection level of Overload 1 (Alarm 50) in respect to the stall (rated) current. Set to "150" as a standard. (For machine tool builder adjustment.)

110 to 500 (Stall [rated] current %)

Set the excessive error detection width when servo ON.

Rapid traverse rate (mm/min)

OD1=OD2= 60*PGN1

/2 (mm)

2223 SV023 OD1

Excessive error detection width during servo ON

When "0" is set, the excessive error detection will not be performed.

0 to 32767 (mm)

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 174

No. Items Details Setting range

2224 SV024 INP

In-position detection width

Set the in-position detection width. Set the accuracy required for the machine. The lower the setting is, the higher the positioning accuracy gets, however, the cycle time (setting time) becomes longer. The standard setting is 50.

0 to 32767 (m)

2225 (PR)

SV025 MTYP

Motor/ Detector type

F E D C B A 9 8 pen ent

7 6 5 4 3 2 1 0 mtyp

bit Explanation 0 Set the motor type.

1 Set- ting 0x 1x 2x 3x 4x 5x 6x 7x

2 x0 HA40N HA50L HA53L 3 x1 HA80N HA100L HA103L 4 x2 HA100N HA200L HA203L 5 x3 HA200N HA300L HA303L 6 x4 HA300N HA500L HA503L 7

mtyp

x5 HA700N x6 HA900N x7 HA-LH11K2 x8 HA-LH15K2 x9 xA HA150L HA153L xB xC xD xE xF

Set- ting 8x 9x Ax Bx Cx Dx Ex Fx

x0 HA43N HC52 HC53 x1 HA83N HC102 HC103 HC103R x2 HA103N HC152 HC153 HC153R x3 HA203N HC202 HC203 HC203R x4 HA303N HC352 HC353 HC353R x5 HA703N HC452 HC453 HC503R x6 HC702 HC703 x7 HC902 x8 x9 xA HA93N xB xC HA053(N) xD HA13(N) xE HA23N xF HA33N

(To be continued to the next page)

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 175

No. Items Details Setting range

(Continued from the previous page) bit Explanation

8 9 A B

ent

Set the detector type. Set position detector type for "pen", and speed detector type for "ent". In the case of the semi-closed loop control, set the same value for "pen" and "ent".

C pen setting ent setting Detector model name

D 0 0 OHE25K (Only for MDS-B-Vx), OSE104

E 1 1 OHA25K (Only for MDS-B-Vx), OSA104

F

pen

2 2 OSE105, OSA105

3 3 Equipped to HA053, HA13 (Only for MDS-B-Vx)

4 Setting impossible OHE25K-ET, OSE104-ET

5 Setting impossible OHA25K-ET, OSA104-ET

6 Setting impossible OSE105-ET, OSA105-ET

7 Setting impossible

8 Setting impossible

Relative position detection scale, MP type (Mitsubishi Heavy Industries)

9 Setting impossible

AT41 (Mitsutoyo), FME type, FLE type (Futaba)

A Setting impossible AT342 (Mitsutoyo)

B Setting impossible

C

C (Current

synchroni- zation)

The setting of the slave axis in the speed/current synchronization control. When the master axis is the semi-closed control.

D Setting impossible

E Setting impossible

F Setting impossible

2226 SV026

OD2 Excessive error detection width during servo OFF

Set the excessive error detection width when servo ON. For the standard setting, refer to the explanation of SV023 (OD1). When "0" is set, the excessive error detection will not be performed.

0 to 32767 (mm)

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 176

No. Items Details Setting range

2227 SV027 SSF1

Servo function selection 1

F E D C B A 9 8 aflt zrn2 afse ovs lmc

7 6 5 4 3 2 1 0 zrn3 vfct upc vcnt

bit Meaning when "0" is set Meaning when "1" is set

0 vcnt Set the execution changeover type of the speed loop delay compensation.

1

00: Delay compensation changeover invalid 01: Delay compensation changeover type 1 10: Delay compensation type 2 11: Setting prohibited

2 upc Start torque compensation invalid

Start torque compensation valid

3

4 Set the number of compensation pulses of the jitter compensation.

5 vfct

00: Jitter compensation invalid 01: Jitter compensation 1 pulse 10: Jitter compensation 2 pulses 11: Jitter compensation 3 pulses

6 zrn3 ABS scale: Set to "1" in using AT342, AT343, LC191M/491M. 7

8 Set the compensation amount with SV016 (LMC1) and SV041 (LMC2).

9 lmc

00: Lost motion compensation stop 01: Lost motion compensation type 1 10: Lost motion compensation type 2 11: Setting prohibited

A Set the compensation amount with SV031 (OVS1) and SV042 (OVS2).

B ovs

00: Overshooting compensation stop 01: Overshooting compensation type 1 10: Overshooting compensation type 2 11: Overshooting compensation type 3

C 00: Adoptive filter sensitivity standard D afse 11: Adoptive filter sensitivity increase (Set 2bits at a time) E zrn2 Set to "1". F aflt Adoptive filter stops Adoptive filter starts

(Note) Set to "0" for bits with no particular description. 2228 SV028 Not used. Set to "0". 0 2229 SV029

VCS Speed at the change of speed loop gain

If the noise is bothersome at high speed during rapid traverse, etc, lower the speed loop gain. Set the speed at which the speed loop gain changes, and use this with SV006 (VGN2). (Refer to SV006.) When not using, set to "0".

0 to 9999 (r/min)

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 177

No. Items Details Setting range

The higher order 8bits and lower order 8bits are used for different functions. "The setting value of SV030" = (Icx*256) + IVC

0 to 32767

SV030 IVC (Low order)

Voltage dead time compensation

When 100% is set, the voltage equivalent to the logical non-energized time will be compensated. When "0" is set, a 100% compensation will be performed. Adjust in increments of 10% from the default value 100%. If increased too much, vibration or vibration noise may be generated.

0 to 255 (%)

2230

SV030 Icx (High order)

Current bias 1 Set to "0" as a standard. Use this in combination with SV040 and the high order 8bits of SV045.

0 to 127

Set this if overshooting occurs during positioning. This compensates the motor torque during positioning. This is valid only when the overshooting compensation SV027 (SSF1/ovs) is selected. Type 1: When SV027 (SSF1)/ bitB, A (ovs)=01 Set the compensation amount based on the motor's stall current. This compensates overshooting that occurs during pulse feeding. Normally, use Type 2. Type 2: When SV027 (SSF1)/ bitB, A (ovs)=10 Set the compensation amount based on the motor's stall current. Increase by 1% and determine the amount that overshooting doesn't occur. In Type 2, compensation during the feed forward control during circular cutting won't be performed. Type 3: When SV027 (SSF1)/ bitB, A (ovs)=11 Use this to perform the overshooting compensation during circular cutting or the feed forward control. The setting method is the same in Type 2.

2231 SV031 OVS1

Overshooting compensation 1

When you wish different compensation amount depending on the direction When SV042 (OVS2) is "0", compensate with the value of SV031 (OVS1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV042 (OVS2). (SV031: + direction, SV042: - direction. However, the directions may be opposite depending on other settings.) When "-1" is set, the compensation won't be performed in the direction of the command.

-1 to 100 (Stall [rated] current%)

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 178

No. Items Details Setting range

2232 SV032 TOF

Torque offset

Set the unbalance torque of vertical axis and inclined axis.

-100 to 100 (Stall [rated] current %)

2233 SV033 SSF2

Servo function selection 2

F E D C B A 9 8 dos hvx svx

7 6 5 4 3 2 1 0 fhz2 nfd zck

bit Meaning when "0" is set Meaning when "1" is set

0 zck Z phase check valid (Alarm 42) Z phase check invalid

1 nfd1 Set the filter depth for Notch filter 1 (SV038). 2 Value 000 001 010 011 100 101 110 111

3 Depth (dB)

Infntly deep -18.1 -12.0 -8.5 -6.0 -4.1 -2.5 -1.2

Deep Shallow 4 Set the operation frequency of Notch filter 2. 5 0: Invalid 3: 750Hz 6: 375Hz 6 1: 2250Hz 4: 563Hz 7: 321Hz 7

fhz2

2: 1125Hz 5: 450Hz 8 to F: 281Hz 8 svx 9 hvx

Set the performance mode of the servo control. (Only for MDS-C1-Vx) 00: By current loop gain 01: MDS-B-Vx compatible mode selected 10: High gain mode selected 11: High gain mode selected

A B C Digital signal output selection

D dos 0 : MP scale absolute position detection, offset demand signal output

E 1 : Specified speed signal output F 2 to F : Setting prohibited

(Note) Set to "0" for bits with no particular description.

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 179

No. Items Details Setting range

2234 SV034 SSF3

Servo function selection 3

F E D C B A 9 8 ovsn

7 6 5 4 3 2 1 0 os2 zeg has2 has1

bit Meaning when "0" is set Meaning when "1" is set

0 has1 Setting for normal use HAS control 1 valid

(Except for HC) (HC: High acceleration rate support)

1 has2 Setting for normal use HAS control 2 valid (Except for HC) (HC: Overshooting support) 2 3 4

5 zeg Z phase normal edge detection Z phase reverse edge detection

(Setting for normal use) (Valid only when SV027/bit6=1)

6 os2 Setting for normal use Overspeed detection level changeover

7 8 9 A B C D E

F

ovsn

Set the non-sensitive band of the overshooting compensation type 3 in increments of 2m at a time. In the feed forward control, the non-sensitive band of the model position droop is set, and overshooting of the model is ignored. Set the same value as the standard SV040.

(Note) Set to "0" for bits with no particular description.

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 180

No. Items Details Setting range

2235 SV035 SSF4

Servo function selection4

F E D C B A 9 8 clt clG1 cl2n clet cltq

7 6 5 4 3 2 1 0 iup tdt

bit Meaning when "0" is set Meaning when "1" is set 0 Td creation time setting 1 Set to "0". (For machine tool builder adjustment) 2 3 4 5

tdt

6 iup Set to "1" in the case of any motors from HC152 to HC702 and from HC153 to HC453.

7

8 Set the retracting torque for collision detection in respect to the maximum torque of the motor.

9 cltq

00: 100% 01: 90% 10: 80% (Standard) 11: 70% A

clet

Setting for normal use The disturbance torque peak of the latest two seconds is displayed in MPOS of the servo monitor screen.

B cl2n Collision detection method 2 valid Collision detection method 2 invalid

C D

E clG1

Collision detection method 1 Set the collision detection level during cutting feed (G1). The G1 collision detection level=SV060*clG1. When clG1=0, the collision detection method 1 during cutting feed won't function.

F clt Setting for normal use The guide value of the SV059

setting value is displayed in MPOS of the servo monitor screen.

(Note) Set to "0" for bits with no particular description.

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 181

No. Items Details Setting range

2236 (PR)

SV036 PTYP

Power supply type

F E D C B A 9 8 amp rtyp

7 6 5 4 3 2 1 0 ptyp

bit Explanation

0 1 2

When the CN4 connector of the drive unit and the power supply are connected, setting below is necessary. To validate the external emergency stop function, add 40h.

3 Set- ting 0x 1x 2x 3x 4x 5x 6x7x 8x

4 x0 Not used CV-300

5 x1 CV-110 CR-10 6 x2 CV-220 CR-15 7

ptyp

x3 CR-22 x4 CV-37 CR-37 x5 CV-150 CV-450 CV-550 x6 CV-55 CV-260 CR-55 x7 CV-370 x8 CV-75 CR-75 x9 CV-185 CR-90 8 Set the regenerative resistor type when MDS-A-CR is used.

9 Set- ting

Regenerative resistor model name

Resistance value Capacity

A 0 MDS-C1-CV (Setting when using power supply regeneration)

B

rtyp

1 GZG200W260HMJ 26 80W 2 GZG300W130HMJ2 26 150W 3 MR-RB30 13 300W 4 MR-RB50 13 500W 5 GZG200W200HMJ3 6.7 350W 6 GZG300W200HMJ3 6.7 500W 7 R-UNIT-1 30 700W 8 R-UNIT-2 15 700W 9 R-UNIT-3 15 2100W

A to F No setting

C D E F

amp

Always set to "0".

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 182

No. Items Details Setting range

Set the motor inertia + motor axis conversion load inertia in respect to the motor inertia.

Jl+Jm SV037 (JL) =

Jm *100

Jm: Motor inertia

2237 SV037 JL Load inertia scale

Jl: Motor axis conversion load inertia

0 to 5000 (%)

2238 SV038 FHz1

Notch filter frequency 1

Set the vibration frequency to suppress if machine vibration occurs. (Valid at 72 or more) When not using, set to "0".

0 to 3000 (Hz)

2239 SV039 LMCD

Lost motion compensation timing

Set this when the lost motion compensation timing doest not match. Adjust by increasing the value by 10 at a time.

0 to 2000 (ms)

The higher order 8bits and lower order 8bits are used for different functions. "Setting value of SV040" = (Icy*256) + LMCT

0 to 32767

SV040 LMCT (Low order)

Lost motion compensation non-sensitive band

Set the non-sensitive band of the lost motion compensation in the feed forward control. When "0" is set, the actual value that is set is 2m. Adjust by increasing by 1m at a time.

0 to 100 (m)

2240

SV040 Icy (High order)

Current bias 2 Normally, set to "40" if you use HC202 to HC902, HC203 to HC703. Use this in combination with SV030 and the high order 8bits of SV045.

0 to 127

2241 SV041 LMC2

Lost motion compensation 2

Set this with SV016 (LMC1) only when you wish to set the lost motion compensation amount to be different depending on the command directions. Set to "0" as a standard.

-1 to 200 (Stall [rated] current %)

2242 SV042 OVS2

Overshooting compensation 2

Set this with SV031 (OVS1) only when you wish to set the overshooting compensation amount to be different depending on the command directions. Set to "0" as a standard.

-1 to 100 (Stall [rated] current %)

2243 SV043 OBS1

Disturbance observer filter frequency

Set the disturbance observer filter band. Set to "100" as a standard. To use the disturbance observer, also set SV037 (JL) and SV044 (OBS2). When not using, set to "0".

0 to 1000 (rad/s)

2244 SV044 OBS2

Disturbance observer gain

Set the disturbance observer gain. The standard setting is "100" to "300". To use the disturbance observer, also set SV037 (JL) and SV043 (OBS1). When not using, set to 0.

0 to 500 (%)

The higher order 8bits and lower order 8bits are used for different functions. "Setting value of SV045" = (Icy*256) + LMCT

0 to 32767

SV045 TRUB (Low order)

Frictional torque

When you use the collision detection function, set the frictional torque.

0 to 100 (Stall [rated] current %)

2245

SV045 Ib1 (High order)

Current bias 3 Set to "0" as a standard. Use this in combination with SV030 and the high order 8bits of SV040.

0 to 127

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 183

No. Items Details Setting range

2246 SV046 Not used. Set to 0. 0 2247 SV047

EC Inductive voltage compensation gain

Set the inductive voltage compensation gain. Set to "100" as a standard. If the current FB peak exceeds the current command peak, lower the gain.

0 to 200 (%)

2248 SV048 EMGrt

Vertical axis drop prevention time

Input a length of time to prevent the vertical axis from dropping by delaying Ready OFF until the brake works when the emergency stop occurs. Increase the setting by 100ms at a time and set the value where the axis does not drop.

0 to 20000 (ms)

2249 SV049 PGN1sp

Position loop gain 1 in spindle synchronous control

Set the position loop gain during the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). Set the same value as the value of the spindle parameter, position loop gain in synchronous control. When performing the SHG control, set this with SV050 (PGN2sp) and SV058 (SHGCsp).

1 to 200 (rad/s)

2250 PGN2sp Position loop gain 2 in spindle synchronous control

Set this with SV049 (PGN1sp) and SV058 (SHGCsp) if you wish to perform the SHG control in the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to "0".

0 to 999 (rad/s)

2251 SV051 DFBT

Dual feed back control time constant

Set the control time constant in dual feed back. When "0" is set, the actual value that is set is 1ms. The higher the time constant is, the closer it gets to the semi-closed control, so the limit of the position loop gain is raised.

0 to 9999 (ms)

2252 SV052 DFBN

Dual feedback control non-sensitive band

Set the non-sensitive band in the dual feedback control. Set to "0" as a standard.

0 to 9999 (m)

2253 SV053 OD3

Excessive error detection width in special control

Set the excessive error detection width when servo ON in a special control (initial absolute position setting, stopper control, etc.). If "0" is set, excessive error detection won't be performed when servo ON during a special control.

0 to 32767 (mm)

2254 SV054 ORE

Overrun detection width in closed loop control

Set the overrun detection width in the full-closed loop control. If the gap between the motor end detector and the linear scale (machine end detector) exceeds the value set by this parameter, it is judged to be overrun and Alarm 43 will be detected. When "-1" is set, the alarm detection won't be performed. When "0" is set, overrun is detected with a 2mm width.

-1 to 32767 (mm)

2255 SV055 EMGx

Max. gate off delay time after emergency stop

Set a length of time from the point when the emergency stop is input to the point when READY OFF is compulsorily executed. Normally, set the same value as the absolute value of SV056. In preventing the vertical axis from dropping, the gate off is delayed for the length of time set by SV048 if SV055's value is smaller than that of SV048.

0 to 20000 (ms)

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 184

No. Items Details Setting range

2256 SV056 EMGt

Deceleration time constant at emergency stop

In the vertical axis drop prevention control, set the time constant used for the deceleration control at emergency stop. Set a length of time that takes from rapid traverse rate (rapid) to stopping. Normally, set the same value as the rapid traverse acceleration/deceleration time constant. When executing the synchronous operation, put the minus sign to the settings of both of the master axis and slave axis.

-20000 to 20000 (ms)

2257 SV057 SHGC

SHG control gain

When performing the SHG control, set this with S003 (PGN1) and SV004 (PGN2). When not performing the SHG control, set to "0".

0 to 999 (rad/s)

2258 SV058 SHGCsp

SHG control gain in spindle synchronous control

Set this with SV049 (PGN1sp) and SV050 (PGN2sp) if you wish to perform the SHG control in the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to "0".

0 to 999 (rad/s)

2259 SV059 TCNV

Collision detection torque estimating gain

Set the torque estimating gain when using the collision detection function. After setting as SV035/bitF(clt)=1 and performing acceleration/deceleration, set the value displayed in MPOS of the NC servo monitor screen. Set to "0" when not using the collision detection function.

-32768 to 32767

2260 SV060 TLMT

Collision detection level

When using the collision detection function, set the collision detection level during the G0 feeding. If "0" is set, none of the collision detection function will work.

0 to 999 (Stall [rated] current %)

2261 SV061 DA1NO

D/A output channel 1 data No.

2262 SV062 DA2NO

D/A output channel 2 data No.

Input the data number you wish to output to D/A output channel. In the case of MDS-C1-V2, set the axis on the side to which the data will not be output to "-1".

-1 to 127

2263 SV063 DA1MPY

D/A output channel 1 output scale

2264 SV064 DA2MPY

D/A output channel 2 output scale

Set the scale with a 1/256 unit. When "0" is set, output is done with the standard output unit.

-32768 to 32767 (Unit: 1/256)

2265 SV065 Not used. Set to "0". 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 185

(2) Initial setting value

(a) HC**/HC**R series

Motor HC 52

HC 102

HC 152

HC 202

HC 352

HC 452

HC 702

HC 902

Drive unit capacity 05 10 20 20 35 45 70 90

SV001 PC1 - - - - - - - - SV002 PC2 - - - - - - - - SV003 PGN1 33 33 33 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 0 0 SV005 VGN1 100 100 100 100 100 100 150 150 SV006 VGN2 0 0 0 0 0 0 0 0 SV007 VIL 0 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 2048 2048 2048 2048 2048 2048 2048 2048 SV010 IDA 2048 2048 2048 2048 2048 2048 2048 2048 SV011 IQG 512 512 512 256 256 256 200 200 SV012 IDG 512 512 512 512 512 512 256 256 SV013 ILMT 500 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - - SV019 RNG1 - - - - - - - - SV020 RNG2 - - - - - - - - SV021 OLT 60 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 50 50 SV025 MTYP xxB0 xxB1 xxB2 xxB3 xxB4 xxB5 xxB6 xxB7 SV026 OD2 6 6 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 0 SV029 VCS 0 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 186

Motor HC 52

HC 102

HC 152

HC 202

HC 352

HC 452

HC 702

HC 902

Drive unit capacity 05 10 20 20 35 45 70 90

SV033 SSF2 0000 0000 0000 0000 0000 0000 0000 0000 SV034 SSF3 0003 0003 0003 0003 0003 0003 0003 0003 SV035 SSF4 0000 0000 0040 0040 0040 0040 0040 0040 SV036 PTYP 0000 0000 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 10240 10240 10240 10240 10240 SV041 LMC2 0 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 0 SV046 0 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 0 SV065 0 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 187

Motor HC 53

HC 103

HC 153

HC 203

HC 353

HC 453

HC 703

HC 103R

HC 153R

HC 203R

HC 353R

Drive unit capacity 05 10 20 35 45 70 90 10 10 20 35

SV001 PC1 - - - - - - - - - - - SV002 PC2 - - - - - - - - - - - SV003 PGN1 33 33 33 33 33 33 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 0 0 0 0 0 SV005 VGN1 100 100 100 100 100 100 100 15 15 20 40 SV006 VGN2 0 0 0 0 0 0 0 0 0 0 0 SV007 VIL 0 0 0 0 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 2048 2048 2048 2048 2048 2048 2048 4096 4096 4096 4096 SV010 IDA 2048 2048 2048 2048 2048 2048 2048 4096 4096 4096 4096 SV011 IQG 256 256 256 256 256 256 256 256 256 256 256 SV012 IDG 512 512 512 512 512 512 512 512 512 512 512 SV013 ILMT 500 500 500 500 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - - - - - SV019 RNG1 - - - - - - - - - - - SV020 RNG2 - - - - - - - - - - - SV021 OLT 60 60 60 60 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 50 50 50 50 50 SV025 MTYP xxC0 xxC1 xxC2 xxC3 xxC4 xxC5 xxC6 xxE1 xxE2 xxE3 xxE4 SV026 OD2 6 6 6 6 6 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 0 0 0 0 SV029 VCS 0 0 0 0 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 188

Motor HC 53

HC 103

HC 153

HC 203

HC 353

HC 453

HC 703

HC 103R

HC 153R

HC 203R

HC 353R

Drive unit capacity 05 10 20 35 45 70 90 10 10 20 35

SV033 SSF2 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV034 SSF3 0003 0003 0003 0003 0003 0003 0003 0000 0000 0000 0000 SV035 SSF4 0000 0000 0040 0040 0040 0040 0040 0000 0000 0000 0000 SV036 PTYP 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 0 0 0 0

SV040 LMCT 0 0 0 1024 0

1024 0

1024 0

1024 0

0 0 0 0

SV041 LMC2 0 0 0 0 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 0 0 0 0 SV046 0 0 0 0 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 0 0 0 0 SV065 0 0 0 0 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 189

(b) HA**N series

Motor HA 40N

HA 80N

HA 100N

HA 200N

HA 300N

HA 700N

HA 900N

Drive unit capacity 05 10 20 35 45 70 90

SV001 PC1 - - - - - - - SV002 PC2 - - - - - - - SV003 PGN1 33 33 33 33 33 25 25 SV004 PGN2 0 0 0 0 0 0 0 SV005 VGN1 150 150 150 150 150 250 250 SV006 VGN2 0 0 0 0 0 0 0 SV007 VIL 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 2048 2048 2048 2048 2048 2048 2048 SV010 IDA 2048 2048 2048 2048 2048 2048 2048 SV011 IQG 512 512 256 256 256 200 200 SV012 IDG 512 512 512 512 512 256 256 SV013 ILMT 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - SV019 RNG1 - - - - - - - SV020 RNG2 - - - - - - - SV021 OLT 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 50 SV025 MTYP xx00 xx01 xx02 xx03 xx04 xx05 xx06 SV026 OD2 6 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 SV029 VCS 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 190

Motor HA 40N

HA 80N

HA 100N

HA 200N

HA 300N

HA 700N

HA 900N

Drive unit capacity 05 10 20 35 45 70 90

SV033 SSF2 0000 0000 0000 0000 0000 0000 0000 SV034 SSF3 0000 0000 0000 0000 0000 0000 0000 SV035 SSF4 0000 0000 0000 0000 0000 0000 0000 SV036 PTYP 0000 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 SV046 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 SV065 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 191

Motor HA 43N

HA 83N

HA 93N

HA 103N

HA 203N

HA 303N

HA 703N

Drive unit capacity 05 10 20 35 45 70 90

SV001 PC1 - - - - - - - SV002 PC2 - - - - - - - SV003 PGN1 33 33 33 33 33 33 25 SV004 PGN2 0 0 0 0 0 0 0 SV005 VGN1 150 150 150 150 150 150 250 SV006 VGN2 0 0 0 0 0 0 0 SV007 VIL 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 2048 2048 2048 2048 2048 2048 2048 SV010 IDA 2048 2048 2048 2048 2048 2048 2048 SV011 IQG 256 256 256 256 256 256 200 SV012 IDG 512 512 512 512 512 512 256 SV013 ILMT 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - SV019 RNG1 - - - - - - - SV020 RNG2 - - - - - - - SV021 OLT 60 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 50 SV025 MTYP xx80 xx81 xx8A xx82 xx83 xx84 xx85 SV026 OD2 6 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 SV029 VCS 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 192

Motor HA 43N

HA 83N

HA 93N

HA 103N

HA 203N

HA 303N

HA 703N

Drive unit capacity 05 10 20 35 45 70 90

SV033 SSF2 0000 0000 0000 0000 0000 0000 0000 SV034 SSF3 0000 0000 0000 0000 0000 0000 0000 SV035 SSF4 0000 0000 0000 0000 0000 0000 0000 SV036 PTYP 0000 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 SV046 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 SV065 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 193

Motor HA 053

HA 13

HA 053N

HA 13N

HA 23N

HA 33N

Drive unit capacity 01 01 01 01 03 03

SV001 PC1 - - - - - - SV002 PC2 - - - - - - SV003 PGN1 33 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 SV005 VGN1 70 70 70 70 100 100 SV006 VGN2 0 0 0 0 0 0 SV007 VIL 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 SV009 IQA 2048 2048 2048 2048 2048 2048 SV010 IDA 2048 2048 2048 2048 2048 2048 SV011 IQG 256 256 256 256 224 224 SV012 IDG 256 256 256 256 224 224 SV013 ILMT 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - SV019 RNG1 10 10 - - - - SV020 RNG2 10 10 - - - - SV021 OLT 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 SV025 MTYP 338C 338D xx8C xx8D xx8E xx8F SV026 OD2 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 SV029 VCS 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0

(Note) The HA053 and HA13 are dedicated for the MDS-B-Vx.

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 194

Motor HA 053

HA 13

HA 053N

HA 13N

HA 23N

HA 33N

Drive unit capacity 01 01 01 01 03 03

SV033 SSF2 0000 0000 0000 0000 0000 0000 SV034 SSF3 0000 0000 0000 0000 0000 0000 SV035 SSF4 0000 0000 0000 0000 0000 0000 SV036 PTYP 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 SV046 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 SV065 0 0 0 0 0 0

(Note) The HA053 and HA13 are dedicated for the MDS-B-Vx.

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 195

(c) HA**L series

Motor HA 50L

HA 100L

HA 150L

HA 200L

HA 300L

HA 500L

HA- A11KL

HA- A15KL

Drive unit capacity 05 10 10 20 35 45 110 150

SV001 PC1 - - - - - - - - SV002 PC2 - - - - - - - - SV003 PGN1 33 33 33 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 0 0 SV005 VGN1 30 30 30 30 30 50 150 150 SV006 VGN2 0 0 0 0 0 0 0 0 SV007 VIL 0 0 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 1364 1364 SV009 IQA 2048 2048 2048 2048 2048 2048 2048 2048 SV010 IDA 2048 2048 2048 2048 2048 2048 2048 2048 SV011 IQG 512 512 512 512 256 256 512 512 SV012 IDG 512 512 512 512 512 512 512 512 SV013 ILMT 500 500 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - - - SV019 RNG1 - - - - - - - - SV020 RNG2 - - - - - - - - SV021 OLT 60 60 60 60 60 60 60 3 SV022 OLL 150 150 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 50 50 SV025 MTYP xx20 xx21 xx2A xx22 xx23 xx24 xx27 xx28 SV026 OD2 6 6 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 0 0 SV029 VCS 0 0 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 196

Motor HA 50L

HA 100L

HA 150L

HA 200L

HA 300L

HA 500L

HA- A11KL

HA- A15KL

Drive unit capacity 05 10 10 20 35 45 110 150

SV033 SSF2 0000 0000 0000 0000 0000 0000 0000 0000 SV034 SSF3 0000 0000 0000 0000 0000 0000 0000 0000 SV035 SSF4 0000 0000 0000 0000 0000 0000 0000 0000 SV036 PTYP 0000 0000 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 0 0 SV046 0 0 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 0 0 SV065 0 0 0 0 0 0 0 0

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 197

Motor HA 53L

HA 103L

HA 153L

HA 203L

HA 303L

HA 503L

Drive unit capacity 10 20 20 35 45 70

SV001 PC1 - - - - - - SV002 PC2 - - - - - - SV003 PGN1 33 33 33 33 33 33 SV004 PGN2 0 0 0 0 0 0 SV005 VGN1 30 30 30 30 30 50 SV006 VGN2 0 0 0 0 0 0 SV007 VIL 0 0 0 0 0 0 SV008 VIA 1364 1364 1364 1364 1364 1364 SV009 IQA 2048 2048 2048 2048 2048 2048 SV010 IDA 2048 2048 2048 2048 2048 2048 SV011 IQG 512 512 512 512 256 256 SV012 IDG 512 512 512 512 512 512 SV013 ILMT 500 500 500 500 500 500 SV014 ILMTsp 500 500 500 500 500 500 SV015 FFC 0 0 0 0 0 0 SV016 LMC1 0 0 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 0000 0000 SV018 PIT - - - - - - SV019 RNG1 - - - - - - SV020 RNG2 - - - - - - SV021 OLT 60 60 60 60 60 60 SV022 OLL 150 150 150 150 150 150 SV023 OD1 6 6 6 6 6 6 SV024 INP 50 50 50 50 50 50 SV025 MTYP xx30 xx31 xx3A xx32 xx33 xx34 SV026 OD2 6 6 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 4000 4000 SV028 0 0 0 0 0 0 SV029 VCS 0 0 0 0 0 0 SV030 IVC 0 0 0 0 0 0 SV031 OVS1 0 0 0 0 0 0 SV032 TOF 0 0 0 0 0 0 SV033 SSF2 0000 0000 0000 0000 0000 0000

7. Servo Parameters 7.3 MDS-C1-Vx Standard Specification (MDS-B-Vx Compatible)

II - 198

Motor HA 53L

HA 103L

HA 153L

HA 203L

HA 303L

HA 503L

Drive unit capacity 10 20 20 35 45 70

SV034 SSF3 0000 0000 0000 0000 0000 0000 SV035 SSF4 0000 0000 0000 0000 0000 0000 SV036 PTYP 0000 0000 0000 0000 0000 0000 SV037 JL 0 0 0 0 0 0 SV038 FHz1 0 0 0 0 0 0 SV039 LMCD 0 0 0 0 0 0 SV040 LMCT 0 0 0 0 0 0 SV041 LMC2 0 0 0 0 0 0 SV042 OVS2 0 0 0 0 0 0 SV043 OBS1 0 0 0 0 0 0 SV044 OBS2 0 0 0 0 0 0 SV045 TRUB 0 0 0 0 0 0 SV046 0 0 0 0 0 0 SV047 EC 100 100 100 100 100 100 SV048 EMGrt 0 0 0 0 0 0 SV049 PGN1sp 15 15 15 15 15 15 SV050 PGN2sp 0 0 0 0 0 0 SV051 DFBT 0 0 0 0 0 0 SV052 DFBN 0 0 0 0 0 0 SV053 OD3 0 0 0 0 0 0 SV054 ORE 0 0 0 0 0 0 SV055 EMGx 0 0 0 0 0 0 SV056 EMGt 0 0 0 0 0 0 SV057 SHGC 0 0 0 0 0 0 SV058 SHGCsp 0 0 0 0 0 0 SV059 TCNV 0 0 0 0 0 0 SV060 TLMT 0 0 0 0 0 0 SV061 DA1NO 0 0 0 0 0 0 SV062 DA2NO 0 0 0 0 0 0 SV063 DA1MPY 0 0 0 0 0 0 SV064 DA2MPY 0 0 0 0 0 0 SV065 0 0 0 0 0 0

7. Servo Parameters 7.4 Supplement

II - 199

7.4 Supplement

7.4.1 D/A Output Specifications

(1) MDS-B-SVJ2

(a) D/A output specifications Item Explanation

No. of channels 2ch Output cycle 888s (min. value) Output precision 8bit Output voltage range

-10V to 0 to +10V

Output scale setting

1/256 to 128 times

CN3 connector MO1 = pin 4 MO2 = pin 14

Output pins

GND = pin 1,11 Function Offset amount adjustment function

Output clamp function Low path filter function

Option Relay terminal: MR-J2CN3TM Connect from the CN3 connector using the SH21 cable as a lead-in wire.

CN3 Connector

Pin Signal Pin Signal 1 LG 11 LG 2 12 3 SG 13 MBR 4 MO1 14 MO2 5 COM 15 MC 6 16 7 17 8 18 9 19

10 VDD 20 EMGX

7. Servo Parameters 7.4 Supplement

II - 200

(b) Setting the output data

Set the No. of the data to be outputted to each D/A output channel.

# No. Abbrev Parameter name 2261 SV061 DA1NO D/A output channel 1

data No. 2262 SV062 DA2NO D/A output channel 2

data No.

No. Output data Standard output unit

Output cycle

0 0V test output For offset amount adjustment 1 Speed feedback 1000rpm / 2V 888s

2 Current feedback Stall (rated) 100% / 2V 888s

3 Speed command 1000rpm / 2V 888s

4 Current command Stall (rated) 100% / 2V 888s

5 V-phase current value 10A / V 888s 6 W-phase current-value 10A / V 888s

7 Estimated disturbance torque Stall (rated) 100% / 2V 888s

8 Collision detection disturbance torque Stall (rated) 100% / 2V 888s

9 Position feedback (stroke) 100mm / V 3.55ms 10 Position feedback (pulse) 10m / V 3.55ms 11 Position droop mm / V 3.55ms 12 Position droop (x10) 100m / V 3.55ms 13 Position droop (x100) 10m / V 3.55ms 14 Feedrate (FT) 10000(mm/min) / V 888s 15 Feedrate (FT x 10) 1000(mm/min) / V 888s 16 Model position droop mm / V 3.55ms 17 Model position droop (x10) 100m / V 3.55ms 18 Model position droop (x100) 10m / V 3.55ms 19 q-axis current cumulative value - 888s 20 d-axis current cumulative value - 888s 21 Motor load level 100% / 5V 113.7ms 22 Amplifier load level 100% / 5V 113.7ms 23 Regenerative load level 100% / 5V 910.2ms 24 PN bus wire voltage 50V / V (1/50) 888s 25 Speed cumulative item - 888s

26 Cycle counter 0-5V (Regardless of resolution) 888s

27 Excessive error detection amount mm / V 3.55ms

28 Collision detection estimated torque Stall (rated) 100% / 2V 888s

29 Position command (stroke) 100mm / V 3.55ms 30 Position command (pulse) 10m / V 3.55ms

31 to 99 - 100 5V test output - -

101 Saw-tooth wave test output -5 to 5V Cycle: 113.7ms 888s

102 Recutangular wave test output 0 to 5V Cycle: 227.5ms 888s

103 to Setting prohibited

7. Servo Parameters 7.4 Supplement

II - 201

(c) Setting the output scale

When "0" is set, the output will be made with the standard output unit. To change the output unit, set a value other than "0". The scale is set with a 1/256 unit. When 256 is set, the unit will be the same as the standard output.

# No. Abbrev Parameter name 2263 SV063 DA1MPY D/A output channel 1

output scale 2264 SV064 DA2MPY D/A output channel 2

output scale (Example 1) When SV061 = 5, SV063 = 2560

The V-phase current value will be output with 1 A/V unit to D/A output ch.1. (Example 2) When SV063 = 11, SV064 = 128

The position droop will be output with a 2mm/Vunit to D/A output ch.2.

7. Servo Parameters 7.4 Supplement

II - 202

(2) MDS-C1-Vx, MDS-B-Vx, MDS-B-Vx4

(a) D/A Output specifications

Item Explanation No. of channels 2ch Output cycle 888s (min. value) Output precision 8bit Output voltage 0V to 2.5V to +5V Output scale setting

1/256 to 128 times

CN9 connector MO1 = pin 9 MO2 = pin 19

Output pins

GND = pin 1,11 Phase current feed back output function L-axis U-phase current FB : pin 7 L-axis V-phase current FB : pin 17 M-axis U-phase current FB : pin 6

Function

M-axis V-phase current FB : pin 16 Option An drive unit with 2 axes also has 2 channels for D/A output.

Therefore, set the output data of the axis (SV061,62), which is not observed, to "-1".

CN9 Connector Pin Signal Pin Signal 1 LG 11 LG 2 12 3 13 4 14 5 15 6 MUIFB 16 MVIFB 7 LUIFB 17 LVIFB 8 18 9 MO1 19 MO2

10 20

7. Servo Parameters 7.4 Supplement

II - 203

(b) Setting the output data

Set the No. of the data to be outputted to each data D/A output channel.

# No. Abbrev Parameter name 2261 SV061 DA1NO D/A output channel 1

data No. 2262 SV062 DA2NO D/A output channel 2

data No.

No. Output data Standard output unit

Standard setting value of output

scale (Setting values in

SV063, SV064)

Standard output unit

Output cycle

-1 D/A output non-selected

For a drive unit. with 2 axes (MDS-C1-V2). Set for the parameter of the axis which is not used.

13 (in case of 2000rpm)

1000rpm / V 3.55ms

ch1: Speed feedback r/min 9 (in case of 3000rpm)

1500rpm / V 3.55ms0

ch2: Current command Stall% 131 Stall 100% / V 3.55ms

1 Current command Stall% 131 Stall 100% / V 3.55ms 2 - 3 Current feedback Stall% 131 Stall 100% / V 3.55ms 4 - 5 -

6 Position droop NC display unit / 2 328

(When the display unit=1m)

10m / 0.5V 3.55ms

7 -

8 Feedrate (FT) (NC display unit / 2) / comminucation cycle

55 (When 1m, 3.5ms)

1000 (mm/min) / 0.5V 3.55ms

9 -

10 Position command NC display unit / 2 328

(When the display unit=1m)

10m / 0.5V 3.55ms

11 -

12 Position feedback NC display unit / 2 328

(When the display unit=1m)

10m / 0.5V 3.55ms

13 -

14 Collision detection estimated torque Stall% 131 Stall 100% / V 3.55ms

15 Collision detection disturbance torque Stall% 131 Stall 100% / V 3.55ms

64 Current command (High-speed) Internal unit

8 (adjustment

required) - 888s

65 Current feedback (High-speed) Internal unit

8 (adjustment

required) - 888s

(To be continued to the next page)

7. Servo Parameters 7.4 Supplement

II - 204

(Continued from the previous page)

No. Output data Standard output unit

Standard setting value of output

scale (Setting values in

SV063, SV064)

Standard output unit

Output cycle

77 Estimated disturbance torque Internal unit

8 (adjustment

required) - 888s

125 Saw-tooth wave test output 0V to 5V 0 (256) Cycle: 227.5ms 888s

126 Rectangular wave test output 0V to 5V 0 (256) Cycle: 1.7ms 888s

127 2.5V (data 0) test output 2.5V 0 (256) - 888s

(c) Setting the output scale

# No. Abbrev Parameter name

2263 SV063 DA1MPY D/A output channel 1 output scale

2264 SV064 DA2MPY D/A output channel 2 output scale

Usually, the standard setting value is set for the output scale (SV063, SV 064). When "0" is set, the output will be made as well as when "256" is set.

SV063 5 [V] DATA x 256 x 256 (8bit) + 2.5 [V] (offset) = Output voltage [V]

(Example) When outputting the current FB with 100%/V-stall (SV061=3, SV063=131)

131 5 100 x 256 x 256 + 2.5 = 3.499 [V]

7. Servo Parameters 7.4 Supplement

II - 205

7.4.2 Electronic Gears

By setting the ball screw lead, deceleration ratio (or acceleration ratio), and detector resolution correctly with parameters, the command movement amount and machine end movement amount can be matched. The following parameters are related to these electronic gears, and directly affect the machine operation. Take care to set these correctly.

Parameters related to electronic gears SV001 (PC1), SV002 (PC2), SV003 (PGN1)(SV049(PGN1sp)), SV018 (PIT), SV019 (RNG1),

SV020 (RNG2) PC1 and PC2 setting range

As a principle, the setting range of SV001 (PC1) and SV002 (PC2) is 1 to 30. However, if the following conditions are satisfied, a value higher than 30 can be set. Note that the following conditions must be satisfied even when setting a value between 1 and 30. For semi-closed loop:

RNG1 x PC2 PIT x PC1 x IUNIT

PC1 '' < 32767 / PIT'' / IUNIT'' PC2''' < 32767 / RNG1'''

For closed loop: PGN1 x RNG2 x PC2

30 x RNG1 x PC1

PC1''' < 32767 / RNG1''' / C30'' PC2''' < 32767 / RNG2''' / PGN1'

Meaning of symbols PC1''' Value obtained by dividing PC1. PC2'' Value obtained by dividing PC2. PIT(') Value obtained by dividing PIT once (twice). RNG1'(') Value obtained by dividing RNG1 once (twice). RNG2'(') Value obtained by dividing RNG2 once (twice). PGN1' Value obtained by dividing PGN1 once (twice). IUNIT'(') Value obtained by dividing CNC interpolation unit once (twice). C30'(') Value obtained by dividing a number "30" once (twice).

7. Servo Parameters 7.4 Supplement

II - 206

Example of calculating PC1 and PC2 setting range

To use a ball screw lead of 10mm, interpolation unit of 0.5m and OSE104 or OSA104 motor end detector with semi-closed loop. The following parameters are determined by the above conditions. SV018 (PIT) = 10, SV019 (RNG1) = 100, SV020 (RNG2) = 100, IUNIT = 2 Divide the denominator and numerator. PIT' = 1, RGN1' = 10 (Greatest common divisor = 10) IUNIT' = 1, RGN1'' = 5 (Greatest common divisor = 2) Obtain the maximum value of PC1 and PC2 with the calculation expression for the semi-closed loop. PC1' < 32767 / 1 / 1 < 32767 PC2' < 32767 / 5 < 6553 With the above calculations, the setting range for PC1 is 1 to 32767 and for PC2 is 1 to 6553.

To use a rotation table, interpolation unit of 0.5m and OSE104 or OSA104 motor end detector with semi-closed loop. The following parameters are determined by the above conditions.

SV018 (PIT) = 360, SV019 (RNG1) = 100, SV020 (RNG2) = 100, IUNIT = 2 Divide the denominator and numerator.

PIT' = 18, RGN1' = 5 (Greatest common divisor = 20) Obtain the maximum value of PC1 and PC2 with the calculation expression for the closed loop.

PC1' < 32767 / 18 / 2 < 910 PC2' < 32767 / 5 < 6553

With the above calculations, the setting range for PC1 is 1 to 910 and for PC2 is 1 to 6553.

To use a ball screw lead of 10mm, interpolation unit of 0.5m, position loop gain of 33, OSE104 or OSA104 motor end detector with closed loop, and 1m scale machine end detector. The following parameters are determined by the above conditions.

SV018 (PIT) = 10, SV019 (RNG1) = 10, SV020 (RNG2) = 100, IUNIT = 2, PGN1 = 33 Divide the denominator and numerator.

RNG1' = 1, RNG2' = 10 (Greatest common divisor = 10) C30' = 3, RNG2'' = 1 (Greatest common divisor = 10) C30'' = 1, PGN1' = 11 (Greatest common divisor = 3)

Obtain the maximum value of PC1 and PC2 with the calculation expression for the closed loop.

PC1' < 32767 / 1 / 1 < 32767 PC2' < 32767 / 1 / 11 < 2978

With the above calculations, the setting range for PC1 is 1 to 32767 and for PC2 is 1 to 2978.

To use a ball screw lead of 10mm, interpolation unit of 0.5m, position loop gain of 33, OSE105 or OSA105 motor end detector with closed loop, and 1m scale machine end detector.

The following parameters are determined by the above conditions. SV018 (PIT) = 12, SV019 (RNG1) = 12, SV020 (RNG2) = 1000, IUNIT = 2, PGN1 = 33

Divide the denominator and numerator.

RNG1' = 3, RNG2' = 250 (Greatest common divisor = 4) C30' = 3, RNG2'' = 25 (Greatest common divisor = 10) C30'' = 1, PGN1' = 11 (Greatest common divisor = 3)

Obtain the maximum value of PC1 and PC2 with the calculation expression for the closed loop.

PC1' < 32767 / 3 / 1 < 10922 PC2' < 32767 / 25 / 11 < 119

With the above calculations, the setting range for PC1 is 1 to 10922 and for PC2 is 1 to 199.

7. Servo Parameters 7.4 Supplement

II - 207

7.4.3 Lost Motion Compensation

When the motor is to rotate in the clockwise direction (looking from the load side) at the command for the + direction, the command direction is CW. Conversely, when the motor is to rotate in the counterclockwise direction, the command direction is CCW. This rotation direction can be set with the CNC machine parameters. Note that the meaning of the will differ for some servo parameters according to this motor rotation direction. The servo parameters affected by CW/CCW are shown below.

SV016 (LMC1), SV041 (LMC2) (When different values are set for SV016 and SV041) SV031 (OVS1), SV042 (OVS2) (When different values are set for SV031 and SV042) If the lost motion compensation amount is to be changed according to the direction, the

compensation amount at the quadrant changeover point of each arc where the lost motion compensation is applied will be as shown below according to the command polarity.

CW CCW A X: SV041 X: SV016 B Y: SV016 Y: SV041 C X: SV016 X: SV041 D Y: SV041 Y: SV016

+X-X

-Y

+Y

The Y axis command direction changes from the - to + direction.

The X axis command direction changes from the - to + direction.

The X axis command direction changes from the + to - direction.

The Y axis command direction changes from the + to - direction.

A

B

C

D

(Note) The setting value for the parameter is "0" or "-1", the compensation amount is determined as

shown below. Setting value

for SV016 (Setting value

for SV031)

Setting value for SV041

(Setting value for SV041)

Compensation amount

in + direction

Compensation amount

in - direction

0 0 No compensation No compensation n 0 n n 0 m m m n m n m n -1 n No compensation -1 m No compensation m

8. MDS-B-SP/SPH, SPJ2 Spindle Parameters 8.1 MDS-B-SP/SPH, SPJ2 Spindle Base Specifications Parameters

II - 208

8. MDS-B-SP/SPH, SPJ2 Spindle Parameters

The spindle parameter setting and display method will differ according to the CNC being used, so refer to Instruction Manual for each CNC and the following spindles.

MELDAS AC Servo and Spindle MDS-A Series MDS-B Series Specifications Manual .......... BNP-B3759

8.1 MDS-B-SP/SPH, SPJ2 Spindle Base Specifications Parameters

For parameters indicated with a (PR) in the table, turn the NC power OFF after setting. The setting is validated after the power is turned ON again.

No. Items Details Setting range (Unit)

3001 3002 3003 3004

slimit 1 2 3 4

Limit rotation speed

Set spindle rotation speed for maximum motor rotation speed with gears 00, 01, 10, 11. (Set the spindle speed for the S analog output 10V.)

3005 3006 3007 3008

smax 1 2 3 4

Maximum rotation speed

Set maximum spindle rotation speed with gears 00, 01, 10, 11. Set to slimt smax. By comparing the S command value and the value of gear 1 to 4, a spindle gear shift command will be output automatically.

0 to 99999 (r/min)

3009 3010 3011 3012

ssift 1 2 3 4

Shift rotation speed

Set spindle speed for gear shifting with gears 00, 01, 10, 11. (Note) Setting too large value may cause a gear

nicks when changing gears.

0 to 32767 (r/min)

3013 3014 3015 3016

stap 1 2 3 4

Tap rotation speed

Set maximum spindle rotation speed during tap cycle with gears 00, 01, 10, 11.

0 to 99999 (r/min)

3017 3018 3019 3020

stapt 1 2 3 4

Tap time constant

Set time constants for constant inclination synchronous tap cycles for gears 00, 01, 10, 11 (linear acceleration/ deceleration pattern).

1 to 5000 (ms)

8. MDS-B-SP/SPH, SPJ2 Spindle Parameters 8.1 MDS-B-SP/SPH, SPJ2 Spindle Base Specifications Parameters

II - 209

Relationship between spindle limit rotation speed and maximum spindle rotation speed

10V

0 smax1 slimt1 smax2 slimt2 smax(n) slimt(n)

Output voltage (V)

Maximum rotation speed of gear 1 (Parameter setting) Set "0" for any unused gear.

Limit rotation speed of gear 1 (Parameter setting)

Spindle rotation speed (r/min)

Relation between the spindle limit rotation speed and the spindle tap time constant (for the constant inclination synchronous tap cycle)

Execution time constant

slimt(n)

stapt(n)stapt(n)

stapt2

stapt1 0

S command

Time (ms)

slimt(n)

slimt2

slimt1

Time (ms)

Spindle rotation speed (r/min) Spindle rotation speed (r/min)

8. MDS-B-SP/SPH, SPJ2 Spindle Parameters 8.1 MDS-B-SP/SPH, SPJ2 Spindle Base Specifications Parameters

II - 210

# Items Details Setting range (Unit)

3021 sori Orientation rotation speed

Set the spindle orientation rotation speed. Set the rotation speed for when the spindle rotates at the constant rotation speed.

0 to 32767 (r/min)

3022 sgear Encoder gear ratio Set the gear ratio of the spindle to the encoder.

0: 1/1 1: 1/2 2: 1/4 3: 1/8

3023 smini Minimum rotation speed

Set the minimum rotation speed of the spindle. If an S command instructs the rotation speed below this setting, the spindle rotates at the minimum rotation speed set by this parameter.

0 to 32767 (r/min)

3024 (PR)

sout Spindle connection Set the type of the spindle to be connected. 0: No connection with the spindle 1: Serial connection (bus) 2 to 5: Analog output

0 to 5

3025 enc-on Spindle encoder Set connection information of the spindle encoder. 0: No connection 1: Spindle connection (Spindle encoder connection check function valid.) 2: Serial connection of encoder

0 to 2

3026 cs_ori Selection of winding in orientation mode

0: Perform orientation using the winding selected when the orientation command is issued.

1: Use winding L whenever the orientation command is issued.

0/1

3027 cs_syn Selection of winding in spindle synchronous mode

0: The winding H/L is selected by the actual spindle motor rotation speed (calculated from commanded rotation speed) when spindle synchronous control starts. (The winding is not switched during synchronous control. The control is carried out with the winding selected at start.) If the actual spindle motor rotation speed is less than SP020, the winding L is selected, and if more than the value, the winding H is selected.

1: Use winding H whenever the spindle synchronous command is issued.

0/1

3028 sprcmm L system tap cycle spindle forward run/ reverse run M command

Set the M code of the spindle forward run/reverse run command. High-order three digits: The spindle

forward run command's M code is set.

Low-order three digits: The spindle reverse run command's M code is set.

0 to 999999

8. MDS-B-SP/SPH, SPJ2 Spindle Parameters 8.1 MDS-B-SP/SPH, SPJ2 Spindle Base Specifications Parameters

II - 211

# Items Details Setting range (Unit)

3029 tapsel Asynchronous tap gear selection

Specify whether to use the tap rotation speed or maximum rotation speed for the gear that is selected when an asynchronous tap command is issued. 0: Tap rotation speed 1: Maximum rotation speed This parameter is valid only when the M-function synchronous tap cycle enable parameter (#1272 ext08 bit1) is ON.

0/1

3030 (PR)

mbsel Selection of magnetic bearings

Select whether to use magnetic bearings. 0: Magnetic bearings invalid 1: Magnetic bearings valid

0/1

3031 (PR)

smcp_no Amplifier I/F channel No. (spindle)

Using a 4-digit number, set the amplifier interface channel No. and which axis in that channel is to be used when connecting a spindle amplifier. High-order two digits : Amplifier interface channel No. Low-order two digits : Axis No. When using the conventional fixed layout, set all axes to "0000". Set "0000" when using an analog spindle.

0000 0101 to 0107 0201 to 0207

3032 (PR)

mbmcp_no Amplifier I/F channel No. (magnetic bearing)

Using a 4-digit number, set the amplifier interface channel No. and which axis in that channel is to be used when connecting a magnetic bearing amplifier. High-order two digits : Amplifier interface channel No. Low-order two digits : Axis No. When using the conventional fixed layout, set all axes to "0000".

0000 0101 to 0107 0201 to 0207

3036 tap_errm Synchronous tap tolerable error width

Set the tolerable value for synchronous tap error width. When "0" is set, synchronous tap error monitoring will not be executed.

0 to 1000 (s)

3037 3038 3039 3040

taps21 22 23 24

Synchronous tap switching spindle speed 2

Set the spindle rotation speed at which the step-2 acceleration/deceleration time constant is to be switched at gear 00, 01, 10, or 11.

0 to 99999 (r/min)

3041 3042 3043 3044

tapt 21 22 23 24

Synchronous tap switching time constant 2

Set the time constant to reach synchronous tap switching spindle rotation speed 2 (#3037 to #3040) at gear 00, 01, 10, or 11.

1 to 5000 (ms)

3045 3046 3047 3048

tapt 31 32 33 34

Synchronous tap switching time constant 3

Set the time constant to reach the maximum rotation speed (#3005 to #3008) at gear 00, 01, 10, or 11.

1 to 5000 (ms)

8. MDS-B-SP/SPH, SPJ2 Spindle Parameters 8.1 MDS-B-SP/SPH, SPJ2 Spindle Base Specifications Parameters

II - 212

# Items Details Setting range (Unit)

3049 spt Spindle synchroniza- tion acceleration/ deceleration time constant

Set the acceleration/deceleration time constant for when the spindle synchronization command's rotation speed changes during spindle synchronous control.

0 to 9999 (ms)

3050 sprlv Spindle synchroniza- tion rotation speed attainment level

The spindle rotation speed synchronization complete signal will turn ON when the difference of the reference spindle and synchronous spindle actual rotation speeds is less than the level set for the synchronous spindle rotation speed command value during spindle synchronous control.

0 to 4095 (pulse) (1 pulse = 0.088)

3051 spplv Spindle phase synchroniza- tion attainment level

The spindle phase synchronization complete signal will turn ON when the phase difference of the reference spindle and synchronous spindle is less than the set level during spindle phase synchronization control.

0 to 4095 (pulse) (1 pulse = 0.088)

3052 spplr Spindle motor spindle relative polarity

Set the spindle motor and spindle's relative polarity. Spindle CW rotation at motor CW rotation: Positive polarity Spindle CCW rotation at motor CW rotation: Negative polarity

0: Positive polarity 1: Negative polarity

3053 sppst Spindle encoder Z -phase position

Set the deviation amount from the spindle's reference position to the spindle encoder's Z phase. The deviation amount is obtained using the clockwise direction looking from the front of the spindle as the positive direction.

0 to 359999 (1/1000)

3054 sptc1 Spindle synchroniza- tion multi-step acceleration/ deceleration changeover speed 1

Set the spindle speed for changing the 1st step's acceleration/deceleration time constant.

0 to 99999 (r/min)

8. MDS-B-SP/SPH, SPJ2 Spindle Parameters 8.1 MDS-B-SP/SPH, SPJ2 Spindle Base Specifications Parameters

II - 213

# Items Details Setting range (Unit)

3055 sptc2 Spindle synchroniza- tion multi-step acceleration/ deceleration changeover speed 2

Set the spindle speed for changing the 2nd step's acceleration/deceleration time constant.

0 to 99999 (r/min)

3056 sptc3 Spindle synchroniza- tion multi-step acceleration/ deceleration changeover speed 3

Set the spindle speed for changing the 3rd step's acceleration/deceleration time constant.

0 to 99999 (r/min)

3057 sptc4 Spindle synchroniza- tion multi-step acceleration/ deceleration changeover speed 4

Set the spindle speed for changing the 4th step's acceleration/deceleration time constant.

0 to 99999 (r/min)

3058 sptc5 Spindle synchroniza- tion multi-step acceleration/ deceleration changeover speed 5

Set the spindle speed for changing the 5th step's acceleration/deceleration time constant.

0 to 99999 (r/min)

3059 sptc6 Spindle synchroniza- tion multi-step acceleration/ deceleration changeover speed 6

Set the spindle speed for changing the 6th step's acceleration/deceleration time constant.

0 to 99999 (r/min)

8. MDS-B-SP/SPH, SPJ2 Spindle Parameters 8.1 MDS-B-SP/SPH, SPJ2 Spindle Base Specifications Parameters

II - 214

# Items Details Setting range (Unit)

3060 sptc7 Spindle synchroniza- tion multi-step acceleration/ deceleration changeover speed 7

Set the spindle speed for changing the 7th step's acceleration/deceleration time constant.

0 to 99999 (r/min)

3061 spdiv1 Magnification for time constant changeover speed 1

Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 1 (sptc1) to the spindle synchronization multi-step acceleration/ deceleration changeover speed 2 (sptc2) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt).

0 to 127

3062 spdiv2 Magnification for time constant changeover speed 2

Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 2 (sptc2) to the spindle synchronization multi-step acceleration/deceleration changeover speed 3 (sptc3) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt).

0 to 127

3063 spdiv3 Magnification for time constant changeover speed 3

Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 3 (sptc3) to the spindle synchronization multi-step acceleration/deceleration changeover speed 4 (sptc4) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt).

0 to 127

3064 spdiv4 Magnification for time constant changeover speed 4

Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 4 (sptc4) to the spindle synchronization multi-step acceleration/deceleration changeover speed 5 (sptc5) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt).

0 to 127

3065 spdiv5 Magnification for time constant changeover speed 5

Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 5 (sptc5) to the spindle synchronization multi-step acceleration/deceleration changeover speed 6 (sptc6) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt).

0 to 127

8. MDS-B-SP/SPH, SPJ2 Spindle Parameters 8.1 MDS-B-SP/SPH, SPJ2 Spindle Base Specifications Parameters

II - 215

# Items Details Setting range (Unit)

3066 spdiv6 Magnification for time constant changeover speed 6

Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 6 (sptc6) to the spindle synchronization multi-step acceleration/deceleration changeover speed 7 (sptc7) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt).

0 to 127

3067 spdiv7 Magnification for time constant changeover speed 7

Set the acceleration/deceleration time constant for the spindle synchronization multi-step acceleration/ deceleration changeover speed 7 (sptc7) and higher as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt).

0 to 127

3068 symtm1 Phase synchroniza- tion start confirmation time

Set the time to confirm that synchronization is attained before phase synchronization control is started. When "0" is set, the time will be 2 seconds. When "100" or less is set, the time will be 100ms.

0 to 9999 (ms)

3069 symtm2 Phase synchroniza- tion end confirmation time

Set the time to wait for phase synchronization control to end as the time for the rotation speed to reach the attainment range. When "0" is set, the time will be 2 seconds. When "100" or less is set, the time will be 100ms.

0 to 9999 (ms)

3070 syprt Phase synchroniza- tion speed

Set the fluctuation amount to change the synchronous spindle rotation speed during phase synchronization control as the command speed and rate. When "0" is set, the amount will be 100%.

0 to 100 (%)

3071 (Not used.) 3072 (Not used.)

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 216

8.2 MDS-B-SPJ2

For parameters marked with a (PR) in the tables, turn the NC power OFF after setting. The parameters will be valid after the power is turned ON again. The valid spindle parameters will differ according to the motor and amplifier type. Follow the correspondence table given below, and set the correct parameters. The spindle parameter setting and display method will differ according to the NC being used, so refer to Instruction Manual for each NC and the following spindles.

MELDAS AC Servo and Spindle MDS-A Series MDS-B Series Specifications Manual ... BNP-B3759

The "fixed control constants" and "fixed control bits" in this section are set by Mitsubishi.

! CAUTION

! Do not make remarkable adjustments or changes of the parameters as the operation may become unstable.

! In the explanation on bits, set all bits not used, including blank bits, to 0.

No. Items Details Setting range

Standard setting

3201 SP001 PGM Magnetic detector and motor built- in encoder orientation- mode position loop gain

As the set value is larger, the orientation time becomes shorter and servo rigidity is increased. On the contrary, however, vibration is increased and the machine becomes likely to overshoot.

0 to 1000 (0.1 1/s)

100

3202 SP002 PGE Encoder orientation-mo de position loop gain

As the set value is larger, the orientation time becomes shorter and servo rigidity is increased. On the contrary, however, vibration is increased and the machine becomes likely to overshoot.

0 to 1000 (0.1 1/s)

100

3203

SP003 Not used. Set to "0". 0 0

3204 SP004 OINP Orientation in-position width

Set the position error range in which an orientation completion signal is output.

1 to 2880 (1/16)

16

3205 (PR)

SP005 OSP Orientation mode changing speed limit value

Set the motor speed limit value to be used when the speed loop is changed to the position loop in orientation mode. When this parameter is set to "0", SP017 (TSP) becomes the limit value.

0 to 32767 (r/min)

0

3206 SP006 CSP Orientation mode dece- leration rate

As the set value is larger, the orientation time becomes shorter. On the contrary, however, the machine becomes likely to overshoot.

1 to 1000 20

3207 SP007 OPST In-position shift amount for orientation

Set the stop position for orientation. Set the value by dividing 360 by 4096.

0 to 4095 0

3208

SP008 Not used. Set to "0". 0 0

3209 SP009 PGT Synchronous tapping position loop gain

Set the spindle position loop gain in synchronous tapping mode.

1 to 100 (1/s)

15

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 217

No. Items Details Setting range

Standard setting

3210 SP010 PGS Spindle synchronous position loop gain

Set the spindle position loop gain in spindle synchronization mode.

1 to 100 (1/s)

15

3211 to

3216

SP011 to

SP016

Use not possible. 0 0

3217 (PR)

SP017 TSP Maximum motor speed

Set the maximum motor speed of the spindle.

1 to 32767 (r/min)

6000

3218 (PR)

SP018 ZSP Motor zero speed

Set the motor speed for which zero-speed output is performed.

1 to 1000 (r/min)

50

3219 (PR)

SP019 CSN1 Speed cushion 1 Set the time constant for a speed command from "0" to the maximum speed. (This parameter is invalid in position loop mode.)

0 to 32767 (10ms)

30

3220 (PR)

SP020 SDTS Speed detection set value

Set the motor speed so for which speed detection output is performed. Usually, the setting value is 10% of SP017 (TSP).

0 to 32767 (r/min)

600

3221

SP021 TLM1 Torque limit 1 Set the torque limit rate for torque limit signal 001.

0 to 120 (%)

10

3222 (PR)

SP022 VGNP1 Speed loop gain proportional term under speed control

Set the speed loop proportional gain in speed control mode. When the gain is increased, response is improved but vibration and sound become larger.

0 to 1000 (1/s)

63

3223 (PR)

SP023 VGNI1 Speed loop gain integral term under speed control

Set the speed loop integral gain in speed control mode. Usually, set a value in proportion to SP022 (VGNP1).

0 to 1000 (0.1 1/s)

60

3224

SP024 Not used. Set to "0". 0 0

3225 (PR)

SP025 GRA1 Spindle gear teeth count 1

Set the number of gear teeth of the spindle corresponding to gear 000.

1 to 32767 1

3226 (PR)

SP026 GRA2 Spindle gear teeth count 2

Set the number of gear teeth of the spindle corresponding to gear 001.

1 to 32767 1

3227 (PR)

SP027 GRA3 Spindle gear teeth count 3

Set the number of gear teeth of the spindle corresponding to gear 010.

1 to 32767 1

3228 (PR)

SP028 GRA4 Spindle gear teeth count 4

Set the number of gear teeth of the spindle corresponding to gear 011.

1 to 32767 1

3229 (PR)

SP029 GRB1 Motor shaft gear teeth count 1

Set the number of gear teeth of the motor shaft corresponding to gear 000.

1 to 32767 1

3230 (PR)

SP030 GRB2 Motor shaft gear teeth count 2

Set the number of gear teeth of the motor shaft corresponding to gear 001.

1 to 32767 1

3231 (PR)

SP031 GRB3 Motor shaft gear teeth count 3

Set the number of gear teeth of the motor shaft corresponding to gear 010.

1 to 32767 1

3232 (PR)

SP032 GRB4 Motor shaft gear teeth count 4

Set the number of gear teeth of the motor shaft corresponding to gear 011.

1 to 32767 1

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 218

No. Items Details Setting range

Standard setting

3233 (PR)

SP033 SFNC1 Spindle function 1

Set the spindle function 1 in bit units.

0000 to FFFF HEX setting

0000

3234 (PR)

SP034 SFNC2 Spindle function 2

Set the spindle function 2 in bit units. (Note1) To validate bit3(mkc2), NC side needs to

prepare. (Note1) Always turn the bit2 at the same time to use

bit3.

0000 to FFFF HEX setting

0000

F E D C B A 9 8 poff hzs ront

7 6 5 4 3 2 1 0 sftk dflt 1a2m

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 1a2m 1 amplifier 2 motor function: Invalid

1 amplifier 2 motor function: Valid

1 dflt Default motor: Main Default motor: Sub 2 sftk SF-TK card invalid SF-TK card valid 3 4 5 6 7 8 9 A B C ront D E hzs F poff

This is a fixed control bit.

F E D C B A 9 8

7 6 5 4 3 2 1 0 mts1

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 mts1 Special motor constant invalid

Special motor constant setting valid

1 2 3 4 5 6 7 8 9 A B C D E F

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 219

No. Items Details Setting range

Standard setting

3235 (PR)

SP035 SFNC3 Spindle function3

Set the spindle function 3 in bit units.

0000 to FFFF HEX setting

0000

3236 (PR)

SP036 SFNC4 Spindle function 4

Set the spindle function 4 in bit units.

F E D C B A 9 8 dslm dssm

7 6 5 4 3 2 1 0 enc2 enc1 mag2 mag1 plg2 plg1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 plg1 PLG of motor 1 valid PLG of motor 1 invalid 1 plg2 PLG of motor 2 valid PLG of motor 2 invalid 2 mag1 MAG of motor 1 valid MAG of motor 1 invalid 3 mag2 MAG of motor 2 valid MAG of motor 2 invalid 4 enc1 ENC of motor 1 valid ENC of motor 1 invalid 5 enc2 ENC of motor 2 valid ENC of motor 2 invalid 6 7 8 dssm Speedometer valid Speedometer invalid 9 dslm Load meter valid Load meter invalid A B C D E F

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 hwid H-coil wide-range constant output invalid

H-coil wide-range constant output valid

1 2 hbsd H-coil base slide invalid H-coil base slide valid 3 4 5 6 7 8 9 A B C D E F

F E D C B A 9 8

7 6 5 4 3 2 1 0 hbsd hwid

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 220

No. Items Details Setting range

Standard setting

3237 (PR)

SP037 SFNC5 Spindle function 5

Set the spindle function 5 in bit units.

0000 to FFFF HEX setting

0000

3238 (PR)

SP038 SFNC6 Spindle function 6

Set the spindle function 6 in bit units. (Note) Always set "0" for the empty bits.

0000 to FFFF HEX setting

0000

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 enco Encoder orientation invalid

Encoder orientation valid

1 2 plgo PLG orientation invalid PLG orientation valid 3 4 5 6 7

8 nstv No-signal detection type

(Always monitoring) Monitoring only in position loop or orientation-mode

9 A B C D E F

F E D C B A 9 8 nstv

7 6 5 4 3 2 1 0 plgo enco

F E D C B A 9 8 oplp

7 6 5 4 3 2 1 0 pftm alty

bit Name Meaning when set to 0 Meaning when set to 1

0 alty Deceleration stop during special alarm invalid

Deceleration stop during special alarm valid

1

2 pftm Thread cutting position data invalid

Thread cutting position data valid

3 4 5 6 7 8 9 A B C D E

F oplp Open loop operation invalid

Open loop operation valid

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 221

No. Items Details Setting range

Standard setting

3239 (PR)

SP039 ATYP Amplifier type

Set the amplifier type. Set each amplifier type or "0". This parameter corresponds to MDS-B-SPJ2.

0000 to FFFF HEX setting

0000

3240 (PR)

SP040 MTYP Motor type 0000 to FFFF HEX setting

0000

This is valid when SP034 (SFNC2) bit 0 is set to 0. Refer to the following standard motors, and set the applicable motor number.

Parameter setting Amplifier type 0000 -- 0001 SPJ2-02 0002 SPJ2-04 0003 SPJ2-075 0004 SPJ2-15 0005 SPJ2-22 0006 SPJ2-37 0007 SPJ2-55 0008 SPJ2-75 0009 SPJ2-110/110C

Paramete r setting Motor type Maximum

speed Corresponding

amplifier 1000 1001 SJ-P0.2A 10000 r/min SPJ2-02 1002 SJ-P0.4A 10000 r/min SPJ2-04 1003 SJ-P0.75A 10000 r/min SPJ2-075 1004 SJ-P1.5A 10000 r/min SPJ2-15 1005 SJ-P2.2A 8000 r/min SPJ2-22 1006 SJ-P3.7A 8000 r/min SPJ2-37 1007 SJ-PF5.5-01 8000 r/min SPJ2-55 1008 SJ-PF7.5-01 8000 r/min SPJ2-75 1009 SJ-PF11-01 6000 r/min SPJ2-110/110C

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 222

No. Items Details Setting range

Standard setting

3241 (PR)

SP041 PTYP Power supply type

When this unit is a signal connection axis with power supply unit, set this parameter. Set "0" for this parameter for the unit which is not a signal connection axis. Select a value from the following table according to the regenerative resistance being used. (Note 1) This setting is used when using one

FCUA-RB75/2 and when using two in parallel.

0000 to FFFF HEX setting

0000

3242 (PR)

SP042 Not used. Set to "0". 0 0

3243 (PR)

SP043 Not used. Set to "0". 0 0

3244 (PR)

SP044 TRANS NC communi- cation frequency

Set a frequency of data communication with NC.

0 to 32767 Standard: 0 Special: 1028

3245

SP045 Not used. Set to "0". 0 0

3246 (PR)

SP046 CSN2 Speed command dual cushion

For an acceleration/deceleration time constant defined in SP019 (CSN1) , this parameter is used to provide smooth movement only at the start of acceleration/deceleration. As the value of this parameter is smaller, it moves smoother but the acceleration/deceleration time becomes longer. To make this parameter invalid, set "0".

0 to 1000 0

3247 (PR)

SP047 SDTR Speed detection reset value

Set the reset hysteresis width for a speed detection set value defined in SP020 (SDTS).

0 to 1000 (r/min)

30

Setting value

Regenerative resistance type

Resistance value ()

Capacity (W)

0000 2000 2100 2200 2300 2400 2500 2600 2700 2800 2900 2A00 2B00 2C00

- Not connected FCUA-RB04 FCUA-RB075 FCUA-RB15 FCUA-RB22 FCUA-RB37 FCUA-RB55 FCUA-RB75/2 R-UNIT-1 R-UNIT-2 R-UNIT-3 R-UNIT-4 R-UNIT-5

- -

200 100 60 40 25 20

30/15 30 15 15 10 10

- -

60 80 120 155 185 340

340/680 700 700

2100 2100 3100

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 223

No. Items Details Setting range

Standard setting

3248 (PR)

SP048 SUT Speed reach range

Set the speed deviation rate with respect to the commanded speed for output of the speed reach signal.

0 to 100 (%)

15

3249 SP049 TLM2 Torque limit 2 Set the torque limit rate for the torque limit signal 010.

1 to 120 (%)

20

3250 SP050 TLM3 Torque limit 3 Set the torque limit rate for the torque limit signal 011.

1 to 120 (%)

30

3251 SP051 TLM4 Torque limit 4 Set the torque limit rate for the torque limit signal 100.

1 to 120 (%)

40

3252 SP052 TLM5 Torque limit 5 Set the torque limit rate for the torque limit signal 101.

1 to 120 (%)

50

3253 SP053 TLM6 Torque limit 6 Set the torque limit rate for the torque limit signal 110.

1 to 120 (%)

60

3254 SP054 TLM7 Torque limit 7 Set the torque limit rate for the torque limit signal 111.

1 to 120 (%)

70

3255 (PR)

SP055 SETM Excessive speed deviation timer

Set the timer value until the excessive speed deviation alarm is output. The value of this parameter should be longer than the acceleration/deceleration time.

0 to 60 (s) 12

3256 SP056 PYVR Variable excitation (min value)

Set the minimum value of the variable excitation rate. Select a smaller value when gear noise is too high. However, a larger value is effective for impact response.

0 to 100 (%)

50

3257 (PR)

SP057 STOD Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

3258 to

3262

SP058 to

SP062

Not used. Set to "0". 0 0

3263 (PR)

SP063 OLT Overload alarm detection time

Set the time constant for detection of the motor overload alarm.

0 to 1000 (s)

60

3264 (PR)

SP064 OLL Overload alarm detection level

Set the detection level of the motor overload alarm.

0 to 120 (%)

110

3265 (PR)

SP065 VCGN1 Target value of variable speed loop proportional gain

Set the magnification of speed loop proportional gain with respect to SP022 (VGNP1) at the maximum motor speed defined in SP017 (TSP).

0 to 100 (%)

100

3266 (PR)

SP066 VCSN1 Change starting speed of variable speed loop proportional gain

Set the speed for starting change of speed loop proportional gain.

SP066 SP017

SP022

SP022 (SP065/100)

Proportional gain

Speed

0 to 32767 (r/min)

0

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 224

No. Items Details Setting range

Standard setting

3267 (PR)

SP067 VIGWA Change starting speed of variable current loop gain

Set the speed for starting change of current loop gain.

0 to 32767 (r/min)

0

3268 (PR)

SP068 VIGWB Change ending speed of variable current loop gain

Set the speed for ending change of current loop gain.

0 to 32767 (r/min)

0

3269 (PR)

SP069 VIGN Target value of variable current loop gain

Set the magnification of current loop gain (torque component and excitation component) for a change ending speed defined in SP068 (VIGWB). When this parameter is set to "0", the magnification is 1.

SP067 SP017SP068

Speed

Gain

SP069(1/16)-fold

1-fold

SP017 (TSP) Maximum

motor speed SP067

(VIGWA) SP068

(VIGWB) SP069 (VIGN)

0 to 6000 0 0 0 6001 to 8000 5000 8000 45 8001 or more 5000 10000 64

0 to 32767 (1/16 -fold)

0

3270

SP070 Not used. Set to "0". 0 0

3271 (PR)

SP071 VR2WA

3272 (PR)

SP072 VR2WB

3273 (PR)

SP073 VR2GN

3274 (PR)

SP074 IGDEC

3275

SP075 R2KWS

Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 225

No. Items Details Setting range

Standard setting

3276

SP076 Not used. Set to "0". 0 0

3277 SP077 TDSL Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

3278 (PR)

SP078 FPWM

3279 (PR)

SP079 ILMT

3280

SP080

3281

SP081 LMCA

3282

SP082 LMCB

3283 to

3286

SP083 to

SP086

Not used. Set to "0".

0 0

3287 (PR)

SP087 DIQM Target value of variable torque limit magnification at deceleration

Set the minimum value of variable torque limit at deceleration.

0 to 150 (%)

75

3288 (PR)

SP088 DIQN Speed for starting change of variable torque limit magnifica- tion at deceleration

Set the speed for starting change of torque limit value at deceleration.

SP088 SP017

100%

SP087

Speed

Inversely proportional to speed

Torque limit

0 to 32767 (r/min)

3000

3289 to

3292

SP089 to

SP092

Not used. Set to "0". 0 0

3293 (PR)

SP093 ORE Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

3294 (PR)

SP094 Not used. Set to 0. 0 0

3295 (PR)

SP095 VFAV Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 226

No. Items Details Setting range

Standard setting

3296 (PR)

SP096 EGAR Encoder gear ratio

Set the gear ratio between the spindle end and the encoder end (except for the motor-built-in encoder) as indicated below.

Setting value

Gear ratio (Acceleration)

1 1 : 2 2 1 : 4 3 1 : 3

Setting value

Gear ratio (deceleration)

0 1 : 1 1 1 : 1/2 2 1 : 1/4 3 1 : 1/8 4 1 : 1/16

-3 to 4 0

3297 (PR)

SP097 SPECO Orientation specifica- tion

Set the orientation specifications in bit units.

0000 to FFFF HEX setting

0000

3298 (PR)

SP098 VGOP Speed loop gain propor- tional term in orientation mode

Set the speed loop proportional gain in orientation mode. When the gain is increased, rigidity is improved in the orientation stop but vibration and sound become larger.

0 to 1000 (1/s)

63

3299 (PR)

SP099 VGOI Orientation mode speed loop gain integral term

Set the speed loop integral gain in orientation mode.

0 to 1000 (0.1 1/s)

60

3300 (PR)

SP100 VGOD Orientation mode speed loop gain delay advance term

Set the a loop gain delay advance gain in orientation mode. When this parameter is set to "0", PI control is exercised.

0 to 1000 (0.1 1/s)

15

F E D C B A 9 8 tlet

7 6 5 4 3 2 1 0 fdir pyfx dmin odi2 odi1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 odi1

1

odi2 Orientation rotation direction 00: Previous (the direction in which the motor has

so far rotated under speed control) 01: Forward rotation 10: Backward rotation 11: Prohibited (Same as setting value = 10)

2 dmin Dummy in-position invalid

Dummy in-position valid

3 pyfx Excitation min. (50%)

during orientation servo lock invalid

Excitation min. (50%) during orientation servo lock valid

4

5 fdir Encoder detector polarity: +

Encoder detector polarity: -

6 7 8 tlet Turret indexing invalid Turret indexing valid 9 A B C D E F

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 227

No. Items Details Setting range

Standard setting

3301 (PR)

SP101 DINP Orientation advance in-position width

When using the orientation in-position advance function, set the in-position width that is larger than the normal in-position width defined in SP004 (OINP).

1 to 2880 (1/16)

16

3302 (PR)

SP102 OODR Excessive error value in orientation mode

Set the excessive error width in orientation mode.

1 to 32767 (1/4 pulse) (1 pulse= 0.088)

32767

3303 (PR)

SP103 FTM Index positioning completion OFF time timer

Set the time for forcedly turn OFF the index positioning completion signal (different from the orientation completion signal) after the leading edge of the indexing start signal.

1 to 10000 (ms)

200

3304 (PR)

SP104 TLOR Torque limit value for orientation servo locking

Set the torque limit value for orientation in-position output. If the external torque limit signal is input the torque limit value set by this parameter is made invalid.

1 to 120 (%)

100

3305 (PR)

SP105 IQG0 Current loop gain magnifica- tion 1 in orientation mode

Set the magnification for current loop gain (torque component) at orientation completion.

1 to 1000 (%)

100

3306 SP106 IDG0 Current loop gain magnifica- tion 2 in orientation mode

Set the magnification for current loop gain (excitation component) at orientation completion.

1 to 1000 (%)

100

3307 SP107 CSP2 Deceleration rate 2 in orientation mode

Set the deceleration rate in orientation mode corresponding to the gear 001. When this parameter is set to "0", same as SP006 (CSP).

0 to 1000 0

3308 SP108 CSP3 Deceleration rate 3 in orientation mode

Set the deceleration rate in orientation mode corresponding to the gear 010. When this parameter is set to "0", same as SP006 (CSP).

0 to 1000 0

3309 (PR)

SP109 CSP4 Deceleration rate 4 in orientation mode

Set the deceleration rate in orientation mode corresponding to the gear 011. When this parameter is set to "0", same as SP006 (CSP).

0 to 1000 0

3310 (PR)

SP110 WCML Turret index command magnifica- tion

The integer magnification (gear ratio 1 : N) for the index position command (0 to 359) is set.

0 to 32767 (fold)

0

3311 SP111 WDEL Turret index deceleration magnifica- tion

The magnification for the orientation deceleration rate is set using 256 as 1.

0 to 32767 (1/256 -fold)

0

3312 SP112 WCLP Turret index clamp speed

The max. speed during indexing is set. This becomes the max. speed of the motor when set to "0".

0 to 32767 (r/min)

0

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 228

No. Items Details Setting range

Standard setting

3313 (PR)

SP113 WINP Turret index in-position width

The position error range is set in which an orientation (indexing) completed signal is output during turret indexing. This becomes the same as SP004 (OINP) when set to "0".

0 to 32767 (1/16)

0

3314 SP114 OPER Orientation pulse miss check value

An alarm "5C" will occur if the pulse miss value in the orientation stop exceed this setting value. (Note that this is invalid when set to "0".) In this parameter, set the value to fulfill the following conditions. SP114 setting value > 1.5 SP004 (orientation in-position width)

0 to 32767 (360/4096)

0

3315 SP115 OSP2 Orientation changeover speed limit value 2

When the door interlock spindle speed clamp signal is ON, this setting is used instead of OSP(SP005), CZRN(SP149) and TZRN(SP214). (Note that SP149 and SP214 are used only for the M65V.)

0 to 32767 (r/min)

0

3316

SP116 OPYVR

3317

SP117 ORUT

Fixed control constants

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

3318 SP118 ORCT Number of orientation retry times

Set the number of times to retry when an orientation or feedback error occurs. The warning (A9) is issued while retrying orientation, and an alarm (5C) is issued when the set number of times is exceeded.

0 to 100 (time)

0

3319 to

3376

SP119 to

SP176

Not used. Set to "0". 0 0

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 229

No. Items Details Setting range

Standard setting

3377 (PR)

SP177 SPECS Spindle synchronous specifica- tions

Set the spindle synchronous specifications in bit units.

0000 to FFFF HEX setting

0000

3378 (PR)

SP178 VGSP Spindle synchronous speed loop gain propor- tional term

Set the speed loop proportional gain in spindle synchronization mode.

0 to 1000 (1/s)

63

3379 (PR)

SP179 VGSI Spindle synchronous speed loop gain integral term

Set the speed loop integral gain in spindle synchronization mode.

0 to 1000 (0.1 1/s)

60

3380 (PR)

SP180 VGSD Spindle synchronous speed loop gain delay advance term

Set the speed loop delay advance gain in spindle synchronization mode. When this parameter is set to "0", PI control is exercised.

0 to 1000 (0.1 1/s)

15

3381 (PR)

SP181 VCGS Target value of variable speed loop proportional gain at spindle synchroniza- tion

Set the magnification of speed loop proportional gain with respect to SP178 (VGSP) at the maximum speed defined in SP017 (TSP) at spindle synchronization.

0 to 100 (%)

100

F E D C B A 9 8 odx8

7 6 5 4 3 2 1 0 fdir pyfx fclx

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 fclx Closed loop Semi-closed loop 1 2

3 pyfx Normal excitation Position loop excitation fixed (strong)

4

5 fdir Position detector polarity (+)

Position detector polarity ()

6 7 8 9 A B C

D odx8 Magnification of

excessive error width 8 times invalid

Magnification of excessive error width 8 times valid

E F

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 230

No. Items Details Setting range

Standard setting

3382 (PR)

SP182 VCSS Change starting speed of variable speed loop proportional gain at spindle synchroniza- tion

Set the speed for starting change of speed loop proportional gain at spindle synchronization.

SP182 SP017

SP178

SP178 (SP181/100)

Proportional gain

Speed

0 to 32767 (r/min)

0

3383 SP183 SYNV Sync match- ing speed at spindle syn- chronization

For changeover from the speed loop to the position loop at spindle synchronization, set a speed command error range for output of the sync speed matching signal.

0 to 1000 (r/min)

20

3384 (PR)

SP184 FFCS Acceleration rate feed forward gain at spindle synchroniza- tion

Set the acceleration rate feed forward gain at spindle synchronization. This parameter is used only with the SPJ2.

0 to 1000 (%)

0

3385 SP185 SINP Spindle sync in-position width

Set the position error range for output of the in-position signal at spindle synchronization.

1 to 2880 (1/16)

16

3386 (PR)

SP186 SODR Excessive error width at spindle synchroniza- tion

Set the excessive error width at spindle synchronization.

1 to 32767 (1/4 pulse) (1 pulse =0.088)

32767

3387 (PR)

SP187 IQGS Current loop gain magnifi- cation1 at spindle syn- chronization

Set the magnification of current loop gain (torque component) at spindle synchronization.

1 to 1000 (%)

100

3388 (PR)

SP188 IDGS Current loop gain magnifi- cation 2 at spindle syn- chronization

Set the magnification of current loop gain (excitation component) at spindle synchronization.

1 to 1000 (%)

100

3389 to

3392

SP189 to

SP192

Not used. Set to "0". 0 0

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 231

No. Items Details Setting range

Standard setting

3393 (PR)

SP193 SPECT Synchronous tapping specifications

Set the synchronous tapping specifications in bit units.

0000 to FFFF HEX setting

0000

3394 (PR)

SP194 VGTP Synchronous tapping speed loop gain propor- tional term

Set the speed loop proportional gain in synchronous tapping mode.

0 to 1000 (1/s)

63

3395 (PR)

SP195 VGTI Synchronous tapping speed loop gain integral term

Set the speed loop integral gain in synchronous tapping mode.

0 to1000 (0.1 1/s)

60

3396 (PR)

SP196 VGTD Synchronous tapping speed loop gain delay advance term

Set the speed loop delay advance gain in synchronous tapping mode. When this parameter is set to "0", PI control is exercised.

0 to1000 (0.1 1/s)

15

3397

SP197 Not used. Set to "0". 0 0

3398 (PR)

SP198 VCGT Target value of variable speed loop proportional gain at synchronous tapping

Set the magnification of speed loop proportional gain with respect to SP194 (VGTP) at the maximum motor speed defined in SP017 (TSP) at synchronous tapping.

0 to 100 (%)

100

F E D C B A 9 8 zrtn ptyp od8x

7 6 5 4 3 2 1 0 fdir cdir pyfx fclx

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1 0 fclx Closed loop Semi-closed loop 1 2

3 pyfx Normal excitation Position loop excitation fixed (strong)

4 cdir Command polarity (+) Command polarity (-)

5 fdir Position detector polarity (+)

Position detector polarity (-)

6 7 8 9 A B C

D od8x Magnification of

excessive error width 8 times invalid

Magnification of excessive error width 8 times valid

E ptyp Position control switch

type: After zero point return

Position control switch type: After deceleration stop

F zrtn Zero point return direction: CCW

Zero point return direction: CW

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 232

No. Items Details Setting range

Standard setting

3399 (PR)

SP199 VCST Change starting speed of variable speed loop proportional gain at synchronous tapping

Set the speed for starting change of speed loop proportional gain at synchronous tapping.

SP199 SP017

SP194

SP194 (SP198/100) Speed

Proportional gain

0 to 32767 (r/min)

0

3400 (PR)

SP200 FFC1 Synchronous tapping acceleration feed forward gain (gear 1)

Set the acceleration feed-forward gain for selection of gear 000 at synchronous tapping. This parameter should be used when an error of relative position to Z-axis servo is large.

0 to 1000 (%)

0

3401 (PR)

SP201 FFC2 Synchronous tapping acceleration feed forward gain (gear 2)

Set the acceleration feed-forward gain for selection of gear 001 at synchronous tapping.

0 to 1000 (%)

0

3402 (PR)

SP202 FFC3 Synchronous tapping acceleration feed forward gain (gear 3)

Set the acceleration feed-forward gain for selection of gear 010 at synchronous tapping.

0 to 1000 (%)

0

3403 (PR)

SP203 FFC4 Synchronous tapping acceleration feed forward gain (gear 4)

Set the acceleration feed-forward gain for selection of gear 011 at synchronous tapping.

0 to 1000 (%)

0

3404 to

3413

SP204 to

SP213

Not used. Set to "0". 0 0

3414 SP214 TZRN Synchronous tapping zero point return speed

This parameter is valid when SP193 (SPECT) bitE is set to "0". Set the zero point return speed used when the speed loop changes to the position loop.

0 to 500 (r/min)

50

3415 SP215 TPDT Synchronous tapping zero point return deceleration rate

This parameter is valid when SP193 (SPECT) bitE is set to "0". Set the deceleration rate where the machine starts to decelerate when it returns to the target stop point during synchronous tapping zero point return. When the machine tends to overshoot at the stop point set a smaller value.

1 to 10000 (pulse)

1

3416 SP216 TPST Synchronous tapping zero point return shift amount

This parameter is valid when SP193 (SPECT) bitE is set to "0". Set the synchronous tapping zero point position.

0 to 4095 0

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 233

No. Items Details Setting range

Standard setting

3417 SP217 TINP Synchronous tapping in-position width

Set the position error range in which in-position signal is output during synchronous tapping.

1 to 2880 (1/16)

16

3418 (PR)

SP218 TODR Excessive error width at synchronous tapping

Set the excessive error width at synchronous tapping.

1 to 32767 (pulse) (1 pulse =0.088)

32767

3419 (PR)

SP219 IQGT Current loop gain magnifi- cation 1 at synchronous tapping

Set the magnification of current loop gain (torque component) during synchronous tapping.

1 to 1000 (%)

100

3420 (PR)

SP220 IDGT Current loop gain magnifi- cation 2 at synchronous tapping

Set the magnification of current loop gain (excitation component) during synchronous tapping.

1 to 1000 (%)

100

3421 to

3424

SP221 to

SP224

Not used. Set to "0". 0 0

3425

SP225 OXKPH

3426

SP226 OXKPL

3427

SP227 OXVKP

3428

SP228 OXVKI

3429

SP229 OXSFT

3430

SP230

3431

SP231

3432

SP232

Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

3433 (PR)

SP233 JL Disturbance observer general inertia scale

Set the ratio of the motor inertia + load inertia and motor inertia. Setting value = Motor inertia + load inertia

Motor inertia 100

(Normally, set "100" or more. When less than "50" is set, the setting will be invalid.)

0 to 5000 (%)

0

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 234

No. Items Details Setting range

Standard setting

3434 (PR)

SP234 OBS1 Disturbanc e observer low path filter frequency

Set the frequency of the low path filter for when the disturbance observer is valid. Setting (1/s) = 2f

f: Approx. 1.5 times the disturbance frequency

0 to 1000 (1/s)

0

3435 (PR)

SP235 OBS2 Disturbanc e observer gain

Set the gain for the disturbance observer. 0 to 500 (%)

0

3436 to

3452

SP236 to

SP252

Not used. Set to "0". 0 0

3453 SP253

DA1NO D/A output channel 1 data number

Set the output data number for channel 1 of the D/A output function. When the setting value is "0", the output is speedometer. Refer to "8.5.1 D/A Output Specifications".

-32768 to 32767

0

3454 SP254 DA2NO D/A output channel 2 data number

Set the output data number for channel 2 of the D/A output function. When the setting value is "0", the output is load meter. Refer to "8.5.1 D/A Output Specifications".

-32768 to 32767

0

3455 SP255 DA1MPY DA output channel 1 magnifica- tion

Set the data magnification for channel 1 of the D/A output function. The output magnification is (setting value)/256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "8.5.1 D/A Output Specifications".

-32768 to 32767 (1/256-fold)

0

3456 SP256 DA2MPY DA output channel 2 magnifica- tion

Set the data magnification for channel 2 of the D/A output function. The output magnification is (setting value)/256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "8.5.1 D/A Output Specifications".

-32768 to 32767 (1/256-fold)

0

8. Spindle Parameters 8.2 MDS-B-SPJ2

II - 235

No. Items Details Setting range

Standard setting

3457 (PR)

to 3520 (PR)

SP257

to SP320

RPM BSD

Motor constant (H coil)

This parameter is valid only in the following two conditional cases: (a) In case that SP034 (SFNC2) bit0=1

and SP034 (SFNC2) bit2=0 Set the motor constants when using a special motor, not described in the SP040 (MTYP) explanation and when not using the coil changeover motor.

(b) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=1 Set the motor constant of the H coil of the coil changeover motor.

(Note) It is not allowed for the user to

change the setting.

0000 to FFFF HEX setting

0000

3521 (PR)

to 3584 (PR)

SP321

to SP384

RPML BSDL

Motor constant (L coil)

This parameter is valid only in the following conditional case: (a) In case that SP034 (SFNC2) bit0=1

and SP034 (SFNC2) bit2=1 Set the motor constant of the L coil of the coil changeover motor.

(Note) It is not allowed for the user to

change the setting.

0000 to FFFF HEX setting

0000

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 236

8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

The spindle parameter setting and display method will differ according to the NC being used, so refer to Instruction Manual for each NC and the following spindles.

MELDAS AC Servo and Spindle MDS-A Series MDS-B Series Specifications Manual . BNP-B3759 MELDAS AC Servo and Spindle MDS-C1 Series Specifications Manual ...................... BNP-C3000

For parameters marked with a (PR) in the tables, turn the NC power OFF after setting. The parameters will be valid after the power is turned ON again. The "fixed control constants" and "fixed control bits" in this section are set by Mitsubishi.

! CAUTION

! Do not make remarkable adjustments or changes of the parameters as the operation may become unstable.

! In the explanation on bits, set all bits not used, including blank bits, to "0".

No. Items Details Setting range

Standard setting

3201 SP001 PGM Magnetic sensor and motor built-in encoder orientation position loop gain

As the set value is larger, the orientation time becomes shorter and servo rigidity is increased. However, vibration is increased and the machine becomes likely to overshoot.

0 to 1000 (0.1 1/s)

100

3202 SP002 PGE Encoder orientation position loop gain

As the set value is larger, the orientation time becomes shorter and servo rigidity is increased. However, vibration is increased and the machine becomes likely to overshoot.

0 to 1000 (0.1 1/s)

100

3203 SP003 PGC0 C-axis non-cutting position loop gain

Set the position loop gain in C-axis non-cutting mode. During non-cutting (rapid traverse, etc.) with the C axis control, this position loop gain setting is valid.

1 to 100 (1/s)

15

3204 SP004 OINP Orientation in-position width

Set the position error range in which an orientation completion signal is output.

1 to 2880 (1/16 )

16

3205 (PR)

SP005 OSP Orientation mode changing speed limit value

Set the motor speed limit value to be used when the speed loop is changed to the position loop in orientation mode. When this parameter is set to "0", SP017 (TSP) becomes the limit value.

0 to 32767 (r/min)

0

3206 SP006 CSP Orientation mode deceleration rate

As the set value is larger, the orientation time becomes shorter. However, the machine becomes likely to overshoot.

1 to 1000 20

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 237

No. Items Details Setting range

Standard setting

3207 SP007 OPST In-position shift amount for orientation

Set the stop position for orientation. (i)Motor built-in encoder, encoder:

Set the value by dividing 360 by 4096. (ii)Magnetic sensor:

Divide -5 to +5 by 1024 and put 0 for 0.

(i) 0 to 4095 (ii) -512 to

512

0

3208

SP008 Not used. Set to "0". 0 0

3209 SP009 PGT Synchroni- zed tapping Position loop gain

Set the spindle position loop gain in synchronized tapping mode.

1 to 100 (1/s)

15

3210 SP010 PGS Spindle synchro- nous position loop gain

Set the spindle position loop gain in spindle synchronization mode.

1 to 100 (1/s)

15

3211 to

3216

SP011 to

SP016

Use not possible. 0 0

3217 (PR)

SP017 TSP Maximum motor speed

Set the maximum motor speed of the spindle. 1 to 32767 (r/min)

6000

3218 (PR)

SP018 ZSP Motor zero speed

Set the motor speed for which zero-speed output is performed.

1 to 1000 (r/min)

50

3219 (PR)

SP019 CSN1 Speed cushion 1

Set the time constant for a speed command from "0" to the maximum speed. (This parameter is invalid in position loop mode.)

1 to 32767 (10ms)

30

3220 (PR)

SP020 SDTS Speed detection set value

Set the motor speed so for which speed detection output is performed. Usually, the setting value is 10% of SP017 (TSP).

0 to 32767 (r/min)

600

3221 SP021 TLM1 Torque limit 1

Set the torque limit rate for torque limit signal 001.

0 to 120 (%) 10

3222 (PR)

SP022 VGNP1 Speed loop gain propor- tional term under speed control

Set the speed loop proportional gain in speed control mode. When the gain is increased, response is improved but vibration and sound become larger.

0 to 1000 (1/s)

63

3223 (PR)

SP023 VGNI1 Speed loop gain integral term under speed control

Set the speed loop integral gain in speed control mode. Usually, set a value in proportion to SP022 (VGNP1).

0 to 1000 (0.1 1/s)

60

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 238

No. Items Details Setting range

Standard setting

3224

SP024 Use not possible. 0 0

3225 (PR)

SP025 GRA1 Spindle gear teeth count 1

Set the number of gear teeth of the spindle corresponding to gear 000.

1 to 32767 1

3226 (PR)

SP026 GRA2 Spindle gear teeth count 2

Set the number of gear teeth of the spindle corresponding to gear 001.

1 to 32767 1

3227 (PR)

SP027 GRA3 Spindle gear teeth count 3

Set the number of gear teeth of the spindle corresponding to gear 010.

1 to 32767 1

3228 (PR)

SP028 GRA4 Spindle gear teeth count 4

Set the number of gear teeth of the spindle corresponding to gear 011.

1 to 32767 1

3229 (PR)

SP029 GRB1 Motor shaft gear teeth count 1

Set the number of gear teeth of the motor shaft corresponding to gear 000.

1 to 32767 1

3230 (PR)

SP030 GRB2 Motor shaft gear teeth count 2

Set the number of gear teeth of the motor shaft corresponding to gear 001.

1 to 32767 1

3231 (PR)

SP031 GRB3 Motor shaft gear teeth count 3

Set the number of gear teeth of the motor shaft corresponding to gear 010.

1 to 32767 1

3232 (PR)

SP032 GRB4 Motor shaft gear teeth count 4

Set the number of gear teeth of the motor shaft corresponding to gear 011.

1 to 32767 1

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 239

No. Items Details Setting range

Standard setting

3233 (PR)

SP033 SFNC1 Spindle function 1

Set the spindle function 1 in bit units.

0000 to FFFF HEX setting

0000 F E D C B A 9 8

poff hzs ront pycal pychg

7 6 5 4 3 2 1 0 pyst pyoff sftk dflt 1a2m

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 1a2m 1 amplifier 2 motor function: Invalid

1 amplifier 2 motor function: Valid

1 dflt Default motor: Main Default motor: Sub 2 sftk SF-TK card invalid SF-TK card valid 3 4 5 6 pyoff 7 pyst 8 pychg

This is used by Mitsubishi. Set to "0" unless particularly designated.

9 pycal (Conventional

specifications) High-speed rate deceleration method valid for minimum excitation rate

A

B This is used by Mitsubishi. Set to "0" unless particularly designated.

C ront Normal ready ON High-speed ready ON

D This is used by Mitsubishi. Set to "0" unless particularly designated.

E hzs Gate OFF by high-cycle zero speed invalid

Gate OFF by high-cycle zero speed valid

F poff Contactor hold at NC power OFF invalid

Contactor hold at NC power OFF valid

(Note) When SPH is used, bit 0 and bit 1 will be invalid.

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 240

No. Items Details Setting range

Standard setting

3234 (PR)

SP034 SFNC2 Spindle function 2

Set the spindle function 2 in bit units.

0000 to FFFF HEX setting

000C

3235 (PR)

SP035 SFNC3 Spindle function 3

Set the spindle function 3 in bit units.

0000 to FFFF HEX setting

0000

F E D C B A 9 8

7 6 5 4 3 2 1 0 mkc2 mkch invm mts1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1

0 mts1 Special motor constant invalid

Special motor constant setting valid

1 invm A general-purpose motor FV control invalid

A general-purpose motor FV control valid

2 mkch Coil switch function invalid Coil switch function valid

3 mkc2 Coil switch specification 2 invalid

Coil switch specification 2 valid (Note1) (Note2)

4 5 6 7 8 9 A B C D E F

(Note1) To validate bit3(mkc2), NC side needs to prepare. (Note2) Always turn the bit2 at the same time to use bit3.

F E D C B A 9 8

7 6 5 4 3 2 1 0 lbsd hbsd lwid hwid

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 hwid H-coil wide-range constant output invalid

H-coil wide-range constant output valid

1 lwid L-coil wide-range constant output invalid

L-coil wide-range constant output valid

2 hbsd H-coil base slide invalid H-coil base slide valid 3 lbsd L-coil base slide invalid L-coil base slide valid 4 5 6 7 8 9 A B C D E F

(Used with SPJ.)

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 241

No. Items Details Setting range

Standard setting

3236 (PR)

SP036 SFNC4 Spindle function 4

Set the spindle function 4 in bit units.

0000 to FFFF HEX setting

0000

3237 (PR)

SP037 SFNC5 Spindle function 5

Set the spindle function 5 in bit units.

0000 to FFFF HEX setting

0000

F E D C B A 9 8 dslm dssm

7 6 5 4 3 2 1 0 enc2 enc1 mag2 mag1 plg2 plg1

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1 0 plg1 PLG of motor 1 valid PLG of motor 1 invalid 1 plg2 PLG of motor 2 valid PLG of motor 2 invalid 2 mag1 MAG of motor 1 valid MAG of motor 1 invalid 3 mag2 MAG of motor 2 valid MAG of motor 2 invalid 4 enc1 ENC of motor 1 valid ENC of motor 1 invalid 5 enc2 ENC of motor 2 valid ENC of motor 2 invalid 6 7

8 dssm Speedometer output valid

Speedometer output invalid

9 dslm Load meter output valid Load meter output invalid

A B C D E F

F E D C B A 9 8 splg dplg noplg nsno nosg

7 6 5 4 3 2 1 0 plgo mago enco

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 enco Encoder orientation invalid

Encoder orientation valid

1 mago Magnetic sensor orientation invalid

Magnetic sensor orientation valid

2 plgo PLG orientation invalid PLG orientation valid 3 4 5 6 7

8 nosg No-signal detection type

(Always monitoring) Monitoring only in position loop or orientation-mode

9 nsno No-signal detection valid

No-signal detection invalid

A noplg Constant monitor of PLG-Z phase no-signal invalid

Constant monitor of PLG-Z phase no-signal valid

B C D E dplg F splg

This is used by Mitsubishi. Set to "0" unless particularly designated.

(Note) For bit0 to 2, do not set two bits or more to "1" at the same time.

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 242

No. Items Details Setting range

Standard setting

3238 (PR)

SP038 SFNC6 Spindle function 6

Set the spindle function 6 in bit units.

0000 to FFFF HEX setting

0000

(Note) Always set "0" for the empty bits.

For MDS-C1-SP/SPH

For MDS-B-SP/SPH

bit Name Meaning when set to 0 Meaning when set to 1

0 alty Deceleration stop during special alarm invalid

Deceleration stop during special alarm valid

1

2 pftm Encoder feedback serial communication invalid

Encoder feedback serial communication valid

3 plg2 Semi-closed pulse output signal 2 invalid

Semi-closed pulse output signal 2 valid

4

5 adin Interpolation during thread cutting invalid

Interpolation during thread cutting valid

6 orm Orientation start memo invalid

Orientation start memo valid

7 vfbs This is used by Mitsubishi. Set to "0" unless particularly designated.

8 sdt2 (Follows SFNC6-bitC setting)

Set output 2 to 2nd speed detection output

9 pl80 MHE90K detector's 180 wave PLG

180 wave PLG other than MHE90K

A lmnp This is used by Mitsubishi. Set to "0" unless particularly designated.

B dcsn Dual cushion during

acceleration/ deceleration valid

Dual cushion during acceleration/ deceleration invalid

C XFzs Set output 2 to MP scale low (L) speed mode

Set output 2 to zero speed output

D iqsv E lmx

This is used by Mitsubishi. Set to "0" unless particularly designated

F oplp Open loop operation invalid

Open loop operation valid

bit Name Meaning when set to 0 Meaning when set to 1

0 alty Deceleration stop during special alarm invalid

Deceleration stop during special alarm valid

1

2 pftm Encoder feedback serial communication invalid

Encoder feedback serial communication valid

3 plg2 Semi-closed pulse output signal 2 invalid

Semi-closed pulse output signal 2 valid

4 tdn 5 adin

Fixed control bit

6 orm Orientation start memo invalid

Orientation start memo valid

7 vfbs 8 sdt2 9 pl80 A lmnp B dcsn C XFzs D iqsv E lmx

Fixed control bit

F oplp Open loop operation invalid

Open loop operation valid

F E D C B A 9 8 oplp lmx iqsv XFzs dcsn lmnp pl80 sdt2

7 6 5 4 3 2 1 0

vfbs orm adin tdn plg2 pftm alty

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 243

No. Items Details Setting range

Standard setting

3239 (PR)

SP039 ATYP Amplifier type

Set the amplifier type. Set each amplifier type or "0"

Parameter setting Amplifier type 0000 0001 SP-075 0002 SP-15 0003 SP-22 0004 SP-37 0005 SP-55 0006 SP-75 0007 SP-110 0008 SP-150 0009 SP-185 000A SP-220 000B SP-260 000C SP-300 000D SP (H)-370 000E SP (H)-450 000F SP-04 0010 SP-550

0000 to FFFF HEX setting

0000

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 244

No. Items Details Setting range

Standard setting

3240 (PR)

SP040 MTYP Motor type This parameter is valid when SP034 (SFNC2) bit0 is set to "0". Set the appropriate motor number from the standard motors listed below.

0000 to FFFF HEX setting

0000

Parameter setting Motor type Maximum

speed Corre-spo

nding amplifier

0000 0001 SJ-2.2A 10000 r/min SP-22 0002 SJ-3.7A 10000 r/min SP-37 0003 SJ-5.5A 8000 r/min SP-55 0004 SJ-7.5A 8000 r/min SP-75 0005 SJ-11A 6000 r/min SP-110 0006 SJ-15A 6000 r/min SP-150 0007 SJ-18.5A 6000 r/min SP-185 0008 SJ-22A 4500 r/min SP-220 0009 SJ-26A 4500 r/min SP-260 000A SJ-30A 4500 r/min SP-300 000B 000C 000D 000E 000F 0010 0011 SJ-N0.75A 10000 r/min SP-075 0012 SJ-N1.5A 10000 r/min SP-15 0013 SJ-N2.2A 10000 r/min SP-22 0014 SJ-N3.7A 10000 r/min SP-37 0015 SJ-N5.5A 8000 r/min SP-55 0016 SJ-N7.5A 8000 r/min SP-75 0017 0018 0019 001A 001B SJ-J2.2A 10000 r/min SP-22 001C SJ-J3.7A 10000 r/min SP-37 001D SJ-J5.5A 8000 r/min SP-55 001E SJ-J7.5A 8000 r/min SP-75 001F

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 245

No. Items Details Setting range

Standard setting

3241 (PR)

SP041 PTYP Power supply type

Power supply type

0000 to FFFF HEX setting

0000

3242 (PR)

SP042 CRNG C-axis detector range

This parameter is used to set the C-axis detector range. Set "0" for this parameter. "2" is used by Mitsubishi for testing.

0 to 7 0

F E D C B A 9 8 amp rtyp

7 6 5 4 3 2 1 0

ptyp bit Explanation

0 1 2

When the CN4 connector of the drive unit and the power supply are connected, setting below is necessary. To validate the external emergency stop function, add 40h.

3 Set- ting 0x 1x 2x 3x 4x 5x 6x 7x 8x

4 x0 Not

used CV-300

5 x1 CV-110 CR-10 6 x2 CV-220 CR-15 7

ptyp

x3 CR-22 x4 CV-37 CR-37 x5 CV-150 CV-450 CV-550 x6 CV-55 CV-260 CR-55 x7 CV-370 x8 CV-75 CR-75 x9 CV-185 CR-90

8 Set the regenerative resistor type when MDS-A-CR is used.

9 Set- ting

Regenerative resistor model name

Resistance value Capacity

A 0 MDS-C1-CV (Setting when using power supply regeneration) B

rtyp

1 GZG200W260HMJ 26 80W 2 GZG300W130HMJ2 26 150W 3 MR-RB30 13 300W 4 MR-RB50 13 500W 5 GZG200W200HMJ3 6.7 350W 6 GZG300W200HMJ3 6.7 500W 7 R-UNIT-1 30 700W 8 R-UNIT-2 15 700W 9 R-UNIT-3 15 2100W A to D No setting E Large capacity + ready ON high-speed sequence F Ready ON high-speed sequence

C D E F

amp

Always set to 0.

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 246

No. Items Details Setting range

Standard setting

3243 (PR)

SP043 TRNG Synchro- nous tapping, spindle synchro- nous detector range

This parameter is used to set the synchronous tapping or spindle synchronous detector range. Set "0" for this parameter.

0 to 7 0

3244 (PR)

SP044 TRANS NC communi- cation frequency

Set a frequency of data communication with NC.

0 to 32767 Standard: 0 Special: 1028

3245 SP045 CSNT Dual cushion timer

Set the cycle to add the increment values in the dual cushion process. When this setting value is increased, the dual cushion will increase, and the changes in the speed during acceleration/deceleration will become gradual.

0 to 1000 (ms)

0

3246 (PR)

SP046 CSN2 Speed command dual cushion

For an acceleration/deceleration time constant defined in SP019 (CSN1) , this parameter is used to provide smooth movement only at the start of acceleration/deceleration. As the value of this parameter is smaller, it moves smoother but the acceleration/deceleration time becomes longer. To make this parameter invalid, set "0".

0 to 1000 0

3247 (PR)

SP047 SDTR Speed detection reset value

Set the reset hysteresis width for a speed detection set value defined in SP020 (SDTS).

0 to 1000 (r/min)

30

3247 (PR)

SP047 SDTR Speed detection reset value

Set the reset hysteresis width for a speed detection set value defined in SP020 (SDTS).

0 to 1000 (r/min)

30

3248 (PR)

SP048 SUT Speed reach range

Set the speed deviation rate with respect to the commanded speed for output of the speed reach signal.

0 to 100 (%)

15

3249 SP049 TLM2 Torque limit 2

Set the torque limit rate for the torque limit signal 010.

1 to 120 (%)

20

3250 SP050 TLM3 Torque limit 3

Set the torque limit rate for the torque limit signal 011.

1 to 120 (%)

30

3251 SP051 TLM4 Torque limit 4

Set the torque limit rate for the torque limit signal 100.

1 to 120 (%)

40

3252 SP052 TLM5 Torque limit 5

Set the torque limit rate for the torque limit signal 101.

1 to 120 (%)

50

3253 SP053 TLM6 Torque limit 6

Set the torque limit rate for the torque limit signal 110.

1 to 120 (%)

60

3254 SP054 TLM7 Torque limit 7

Set the torque limit rate for the torque limit signal 111.

1 to 120 (%)

70

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 247

No. Items Details Setting range

Standard setting

3255 (PR)

SP055 SETM Excessive speed deviation timer

Set the timer value until the excessive speed deviation alarm is output. The value of this parameter should be longer than the acceleration/deceleration time.

0 to 60 (s) 12

3256 SP056 PYVR Variable excitation (min value)

Set the minimum value of the variable excitation rate. Select a smaller value when gear noise is too high. However, a larger value is effective for impact response.

0 to 100 (%)

50

3257 (PR)

SP057 STOD Constant excessive judgment value

Set the value for judging when changing from a constant to excessive speed command.

0 to 50 (r/min)

0

3258 (PR)

SP058 SDT2 Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

3259 (PR)

SP059 MKT Winding changeover base shut-off timer

Set the base shut-off time for contactor switching at winding changeover. Note that the contactor may be damaged with burning if the value of this parameter is too small.

50 to 10000 (ms)

150

3260 (PR)

SP060 MKT2 Current limit timer after winding changeover

Set the current limit time to be taken after completion of contactor switching at winding changeover.

0 to 10000 (ms)

500

3261 (PR)

SP061 MKIL Current limit value after winding changeover

Set the current limit value during a period defined in SP060 (MKT2) after completion of contactor switching at winding changeover.

0 to 120 (%)

75

3262

SP062 Not used. Set to "0". 0 0

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 248

No. Items Details Setting range

Standard setting

3263 (PR)

SP063 OLT Overload alarm detection time

Set the time constant for detection of the motor overload alarm.

0 to 1000 (s)

60

3264 (PR)

SP064 OLL Overload alarm detection level

Set the detection level of the motor overload alarm.

0 to 120 (%)

110

3265 (PR)

SP065 VCGN1 Target value of variable speed loop proportional gain

Set the magnification of speed loop proportional gain with respect to SP022 (VGNP1) at the maximum motor speed defined in SP017 (TSP).

0 to 100 (%)

100

3266 (PR)

SP066 VCSN1 Change starting speed of variable speed loop proportional gain

Set the speed when the speed loop proportional gain change starts.

SP066 SP017

SP022

SP022 (SP065/100)

Proportional gain

Speed

0 to 32767 (r/min)

0

3267 (PR)

SP067 VIGWA Change starting speed of variable current loop gain

Set the speed where the current loop gain change starts.

0 to 32767 (r/min)

0

3268 (PR)

SP068 VIGWB Change ending speed of variable current loop gain

Set the speed where the current loop gain change ends.

0 to 32767 (r/min)

0

3269 (PR)

SP069 VIGN Target value of variable current loop gain

Set the magnification of current loop gain (torque component and excitation component) for a change ending speed defined in SP068 (VIGWB). When this parameter is set to "0", the magnification is 1.

SP067 SP017SP068

Speed

1-fold

SP069(1/16)-fold

0 to 32767 (1/16-fold)

0

SP017 (TSP) Maximum

motor speed

SP067 (VIGWA)

SP068 (VIGWB)

SP069 (VIGN)

0 to 6000 0 0 0 6001 to 8000 5000 8000 45 8001 or more 5000 10000 64

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 249

No. Items Details Setting range

Standard setting

3270 SP070 FHz Machine resonance suppressio n filter frequency

When machine vibration occurs in speed and position control, set the frequency of the required vibration suppression. Note that a value of 100Hz or more is set. Set to "0" when not used.

0 to 3000 (Hz)

0

3271 (PR)

SP071 VR2WA

3272 (PR)

SP072 VR2WB

3273 (PR)

SP073 VR2GN

3274 (PR)

SP074 IGDEC

Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

3275 SP075 R2KWS

3276 SP076 FONS Machine resonance suppressio n filter operation speed

When the vibration increases in motor stop (ex. in orientation stop) when the machine vibration suppression filter is operated by SP070, operate the machine vibration suppression filter at a speed of this parameter or more. When set to "0", this is validated for all speeds.

0 to 32767 (r/min)

0

3277 (PR)

SP077 TDSL Fixed control constant

Set by Mitsubishi. Set "14" unless designated in particular.

14

3278 (PR)

SP078 FPWM

3279 (PR)

SP079 ILMT

Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

F E D C B A 9 8 r2ini

7 6 5 4 3 2 1 0 r2am r2lm r2dn no51 r2ch

bit Name Meaning when set to 0 Meaning when set to 1 0 r2ch 1 no51 2 r2dm 3 r2lm 4 r2am

This is used by Mitsubishi. Set to "0" unless particularly designated.

5 6 7 8 r2ini This is used by Mitsubishi.

Set to "0" unless particularly designated 9 A B C D E F

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 250

No. Items Details Setting range

Standard setting

3280

SP080 Use not possible. 0 0

3281

SP081 LMCA

3282

SP082 LMCB

3283

SP083

Fixed control constant

This is used by Mitsubishi. Set to "0" unless particularly designated.

0 0

3284 to

3286

SP084 to

SP086

Use not possible. 0 0

3287 (PR)

SP087 DIQM Target value of variable torque limit magnifica- tion at deceleration

Set the minimum value of variable torque limit at deceleration.

0 to 150 (%)

75

3288 (PR)

SP088 DIQN Speed for starting change of variable torque limit magnifica- tion at deceleration

Set the speed where the torque limit value at deceleration starts to change.

SP088 SP017

100%

SP087

Torque limit Inversely proportional to speed

0 to 32767 (r/min)

3000

3289

SP089 Use not possible. 0 0

3290

SP090 Use not possible. 0 0

3291 SP091 OFSN Motor PLG forward rotation offset compensa- tion

Set the PLG offset value for the forward rotation. Normally set to "0".

-2048 to 2047 (-1mv)

0

3292 SP092 OFSI Motor PLG reverse rotation offset compensa- tion

Set the PLG offset value for the reverse rotation. Normally set to "0".

-2048 to 2047 (-1mv)

0

3293 (PR)

SP093 ORE Tolerable pulse check error

Set this when detecting the pulse detector's pulse mistakes. (Valid only for full close control.)

0 to 32767 0

3294 (PR)

SP094 LMAV Load meter output filter

Set the filter time constant of load meter output. When "0" is set, a filter time constant is set to 100ms.

0 to 32767 (2ms)

0

3295 (PR)

SP095 VFAV Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 251

No. Items Details Setting range

Standard setting

3296 (PR)

SP096 EGAR Encoder gear ratio

Set the gear ratio between the spindle end and the encoder end (except for the motor-built-in encoder) as indicated below.

Setting value

Gear ratio (acceleration)

-1 1 : 2 -2 1 : 4 -3 1 : 3

Setting value

Gear ratio (deceleration)

0 1 : 1 1 1 : 1/2 2 1 : 1/4 3 1 : 1/8 4 1 : 1/16

-3 to 4 0

3297 (PR)

SP097 SPECO Orientation specifica- tion

Set the orientation specifications in bit units.

0000 to FFFF HEX setting

0000 F E D C B A 9 8

ostp orze ksft gchg ips2 zdir

7 6 5 4 3 2 1 0 vg8x mdir fdir osc1 pyfx dmin odi2 odi1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 odi1

1

odi2 Orientation rotation direction 00: Previous (the direction in which the motor has

so far rotated under speed control) 01: Forward rotation 10: Backward rotation 11: Prohibited (Same as setting value = 10)

2 dmin Orientation in-position advance invalid

Orientation in-position advance valid

3 pyfx Excitation min. (50%)

during orientation servo lock invalid

Excitation min. (50%) during orientation servo lock valid

4 osc1 Indexing speed clamp invalid

Indexing speed clamp valid

5 fdir Encoder detector polarity: +

Encoder detector polarity:

6 mdir Magnetic sensor polarity: +

Magnetic sensor polarity:

7 vg8x Speed gain *1/8 during torque limit valid

Speed gain *1/8 during torque limit invalid

8

9 zdir This is used by Mitsubishi. Set to "0" unless particularly designated.

A ips2 2nd in-position invalid 2nd in-position valid B

C gchg Gain changeover during orientation invalid

Gain changeover during orientation valid

D ksft Orientation virtual target shift invalid

Orientation virtual target shift valid

E orze F ostp

This is used by Mitsubishi. Set to "0" unless particularly designated.

In-position advance (bit 2) 0 (invalid) 1 (valid)

0 (Invalid)

In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=0

S ec

on d

in -p

os iti

on

1 (Valid)

In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=1

In-position signal in DINP width=1 Control output 4/ bit 4=1 Second in-position signal in OINP width = 0 Control output 4/ bit F=1

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 252

No. Items Details Setting range

Standard setting

3298 (PR)

SP098 VGOP Speed loop gain propor- tional term in orientation mode

Set the speed loop proportional gain in orientation mode. When the gain is increased, rigidity is improved in the orientation stop but vibration and sound become larger.

0 to 1000 (1/s)

63

3299 (PR)

SP099 VGOI Orientation mode speed loop gain integral term

Set the speed loop integral gain in orientation mode.

0 to 1000 (0.1 1/s)

60

3300 (PR)

SP100 VGOD Orientation mode speed loop gain delay advance term

Set a loop gain delay advance gain in orientation mode. When this parameter is set to "0", PI control is applied.

0 to 1000 (0.1 1/s)

15

3301 (PR)

SP101 DINP Orientation advance in-position width

When using the orientation in-position advance function, set the in-position width that is larger than the normal in-position width defined in SP004 (OINP).

1 to 2880 (1/16)

16

3302 (PR)

SP102 OODR Excessive error value in orientation mode

Set the excessive error width in orientation mode.

0 to 32767 (1/4 pulse) (1 pulse= 0.088)

32767

3303 (PR)

SP103 FTM Index positioning completion OFF time timer

Set the time for forcedly turn OFF the index positioning completion signal (different from the orientation completion signal) after the leading edge of the indexing start signal.

0 to 10000 (ms)

200

3304 (PR)

SP104 TLOR Torque limit value for orientation servo locking

Set the torque limit value for orientation in-position output. If the external torque limit signal is input, the torque limit value set by this parameter is made invalid.

0 to 120 (%)

100

3305 (PR)

SP105 IQG0 Current loop gain magnifica- tion 1 in orientation mode

Set the magnification for current loop gain (torque component) at orientation completion.

1 to 1000 (%)

100

3306 (PR)

SP106 IDG0 Current loop gain magnifica- tion 2 in orientation mode

Set the magnification for current loop gain (excitation component) at orientation completion.

1 to 1000 (%)

100

3307 SP107 CSP2 Deceleration rate 2 in orientation mode

Set the deceleration rate in orientation mode corresponding to the gear 001. When this parameter is set to "0", same as SP006 (CSP).

0 to 1000 0

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 253

No. Items Details Setting range

Standard setting

3308 SP108 CSP3 Deceleration rate 3 in orientation mode

Set the deceleration rate in orientation mode corresponding to the gear 010. When this parameter is set to "0", same as SP006 (CSP).

0 to 1000 0

3309 SP109 CSP4 Deceleration rate 4 in orientation mode

Set the deceleration rate in orientation mode corresponding to the gear 011. When this parameter is set to "0", same as SP006 (CSP).

0 to 1000 0

3310 to

3313

SP110 to

SP113

Use not possible. 0

3314 SP114 OPER Orientation pulse miss check value

An alarm "5C" will occur if the pulse miss value at the orientation stop exceeds this setting value. (Note that this is invalid when set to "0".) In this parameter, set the value to fulfill the following conditions. SP114 setting value > 1.5 SP004 (orientation in-position width)

0 to 32767 (360/4096)

0

3315 SP115 OSP2 Orientation motor speed clamp value 2

When the orientation clamp speed is changed by the control input, this parameter setting will be used instead of SP005: OSP. Indexing speed clamp valid This parameter is used when (SP097: SPEC0-bit4 = 1).

0 to 32767 (r/min)

0

3316 SP116 OPYVR Minimum excitation value after changeover (2nd minimum excitation rate)

Minimum excitation rate when position control input or external input is selected.

0 to 100 (%) 0

3317 SP117 ORUT This is used by Mitsubishi. Set to "0" unless particularly designated.

0 0

3318 SP118 ORCT Number of orientation retry times

Set the number of times to retry when an orientation or feedback error occurs. The warning (A9) is issued while retrying orientation, and an alarm (5C) is issued when the set number of times is exceeded.

0 to 100 (time)

0

3319 SP119 MPGH Orientation position gain H winding compensa- tion magnifi- cation

Set the compensation magnification of the orientation position loop gain for the H winding. H winding orientation position loop gain = SP001 (or SP002) SP119/256 When set to "0", will become the same as SP001 or SP002.

0 to 2560 (1/256-fold)

0

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 254

No. Items Details Setting range

Standard setting

3320 SP120 MPGL Orientation position gain L winding compensa- tion magnifi- cation

Set the compensation magnification of the orientation position loop gain for the L winding. L winding orientation position loop gain = SP001 (or SP002) SP120/256 When set to "0", will become the same as SP001 or SP002.

0 to 2560 (1/256-fold)

0

3321 SP121 MPCSH Orientation deceleration rate H winding compensa- tion magnifi- cation

Set the compensation magnification of the orientation deceleration rate for the H winding. Orientation deceleration rate for the H winding = SP006 SP121/256 When set to "0", will become the same as SP006.

0 to 2560 (1/256-fold)

0

3322 SP122 MPCSL Orientation deceleration rate L winding compensa- tion magnifi- cation

Set the compensation magnification of the orientation deceleration rate for the L winding. Orientation deceleration rate for the L winding = SP006 SP122/256 When set to "0", will become the same as SP006.

0 to 2560 (1/256-fold)

0

3323 SP123 MGD0 Magnetic sensor output peak value

This parameter is used for adjustment of orientation operation of the magnetic sensor. Set the output peak value of the magnetic sensor. If a gap between the sensor and the magnetizing element is small, increase the value of this parameter. If it is large, decrease the value of this parameter.

1 to 10000 Standard magnet- izing element: 542 Small magnet- izing element: 500

3324 SP124 MGD1 Magnetic sensor linear zone width

This parameter is used for adjustment of orientation operation of the magnetic sensor. Set the linear zone width of the magnetic sensor. If the radius of the mounted magnetizing element is large, decrease the value of this parameter. If it is small, increase the value of this parameter.

1 to 10000 Standard magnet- izing element: 768 Small magnetizin g element: 440

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 255

No. Items Details Setting range

Standard setting

3325 SP125 MGD2 Magnetic sensor switching point

This parameter is used for adjustment of orientation operation of the magnetic sensor. Set the distance dimension from the target stop point at switching from position feedback to magnetic sensor output. Normally, set a value that is approx. 1/2 of the value defined in SP124.

1 to 10000 Standard magnet- izing element: 384 Small magnet- izing element: 220

3326 to

3328

SP126 to

SP128

Use not possible. 0 0

3329 (PR)

SP129 SPECC C-axis specifica- tions

Set the C-axis specifications in bit units.

0000

3330 SP130 PGC1 First position loop gain for cutting on C-axis

Set the position loop gain when the first gain is selected for C axis cutting.

1 to 100 (1/s)

15

3331 SP131 PGC2 Second position loop gain for cutting on C-axis

Set the position loop gain when the second gain is selected for C axis cutting.

1 to 100 (1/s)

15

F E D C B A 9 8 zrtn ptyp fb9x zrtd zrn2 zdir ztyp

7 6 5 4 3 2 1 0

vg8x fdir phos rtrn adin fclx

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 fclx Closed loop Semi-closed loop (Gear 1 : 1 only)

1 adin Interpolation A/D compensation invalid

Interpolation A/D compensation valid

2 rtrn Position monitor during ready OFF invalid

Position monitor during ready OFF valid

3 phos Normal (no compensation)

Vx4 synchronization compensation valid

4

5 fdir Position detector polarity (+)

Position detector polarity ()

6

7 vg8x Speed gain 1/8 during torque limit valid

Speed gain 1/8 during torque limit invalid

8 ztyp Z-phase type: Normal start up Z-phase type: Start up only

9 zdir Z-phase rising polarity (+) Z-phase rising polarity ()

A B zrn2 C zrtd

This is used by Mitsubishi. Set to "0" unless particularly designated.

D fb9x Speed feedback Standard (PLG)

Speed feedback 90,000 pulse detector

E ptyp Position control switch

type: After zero point return

Position control switch type: After deceleration stop

F zrtn Zero point return direction: CCW

Zero point return direction: CW

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 256

No. Items Details Setting range

Standard setting

3332 SP132 PGC3 Third position loop gain for cutting on C-axis

Set the position loop gain when the third gain is selected for C-axis cutting.

1 to 100 (1/s)

15

3333 SP133 PGC4 Stop position loop gain for cutting on C-axis

Set the position loop gain for stopping when carrying out C-axis cutting.

1 to 100 (1/s)

15

3334 (PR)

SP134 VGCP0 C-axis non-cutting speed loop gain proportional item

Set the speed loop proportional gain in C-axis non-cutting mode.

0 to 5000 (1/s)

63

3335 (PR)

SP135 VGCI0 C-axis non-cutting speed loop gain integral item

Set the speed loop integral gain in C-axis non-cutting mode.

0 to 5000 (0.1 1/s)

60

3336 (PR)

SP136 VGCD0 C-axis non-cutting speed loop gain delay advance item

Set the speed loop delay advance gain in C-axis non-cutting mode. When this parameter is set to "0", PI control is exercised.

0 to 5000 (0.1 1/s)

15

3337 (PR)

SP137 VGCP1 First speed loop gain proportional item for C-axis cutting

Set the speed loop proportional gain when the first gain is selected for C-axis cutting.

0 to 5000 (1/s)

63

3338 (PR)

SP138 VGCI1 First speed loop gain integral item for cutting on C-axis

Set the speed loop integral gain when the first gain is selected for C-axis cutting.

0 to 5000 (0.1 1/s)

60

3339 (PR)

SP139 VGCD1 First speed loop gain delay advance item for cutting on C-axis

Set the speed loop delay advance gain when the first gain is selected for curing on the C-axis. When this parameter is set to "0", PI control is applied.

0 to 5000 (0.1 1/s)

15

3340 (PR)

SP140 VGCP2 Second speed loop gain proportional item for cutting on C-axis

Set the speed loop proportional gain when the second gain is selected for C-axis cutting.

0 to 5000 (1/s)

63

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 257

No. Items Details Setting range

Standard setting

3341 (PR)

SP141 VGCI2 Second speed loop gain integral item for cutting on C-axis

Set the speed loop integral gain when the second gain is selected for C-axis cutting.

0 to 5000 (0.1 1/s)

60

3342 (PR)

SP142 VGCD2 Second speed loop gain delay advance item for cutting on C-axis

Set the speed loop delay advance gain when the second gain is selected for C-axis cutting. When this parameter is set to "0", PI control is applied.

0 to 5000 (0.1 1/s)

15

3343 (PR)

SP143 VGCP3 Third speed loop gain proportional item for cutting on C-axis

Set the speed loop proportional gain when the third gain is selected for C-axis cutting.

0 to 5000 (1/s)

63

3344 (PR)

SP144 VGCI3 Third speed loop gain integral item for cutting on C-axis

Set the speed loop integral gain when the third gain is selected for C-axis cutting.

0 to 5000 (0.1 1/s)

60

3345 (PR)

SP145 VGCD3 Third speed loop gain delay advance item for cutting on C-axis

Set the speed loop delay advance gain when the third gain is selected for C-axis cutting. When this parameter is set to "0", PI control is applied.

0 to 5000 (0.1 1/s)

15

3346 (PR)

SP146 VGCP4 Speed loop gain propor- tional item for stop of cutting on C-axis

Set the speed loop proportional gain when C-axis cutting is stopped.

0 to 5000 (1/s)

63

3347 (PR)

SP147 VGCI4 Speed loop gain integral item for stop of cutting on C-axis

Set the speed loop integral gain when C-axis cutting is stopped.

0 to 5000 (0.1 1/s)

60

3348 (PR)

SP148 VGCD4 Speed loop gain delay advance item for stop of cutting on C-axis

Set the speed loop delay advance gain when C-axis cutting is stopped. When this parameter is set to "0", PI control is applied.

0 to 5000 (0.1 1/s)

15

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 258

No. Items Details Setting range

Standard setting

3349 SP149 CZRN C-axis zero point return speed

This parameter is valid when SP129 (SPECC) bitE is set to "0". Set the zero point return speed used when the speed loop changes to the position loop.

1 to 500 (r/min)

50

3350 SP150 CPDT C-axis zero point return deceleration point

This parameter is valid when SP129 (SPECC) bitE is set to "0". Set the deceleration rate where the machine starts to decelerate when it returns to the target stop point during C-axis zero point return. When the machine tends to overshoot at the stop point, set the smaller value.

1 to 10000 1

3351 SP151 CPSTL C-axis zero point return shift amount (low byte)

3352 SP152 CPSTH C-axis zero point return shift amount (high byte)

This parameter is valid when SPECC (SP129) bitE is set to "0". Set the C-axis zero point position.

HEX setting 00000000 to FFFFFFFF (1/1000)

H: 0000 L: 0000

3354 (PR)

SP154 CODRL Excessive error width on C-axis (low byte)

Set the excessive error width on the C-axis. HEX setting 00000000 to FFFFFFFF (1/1000)

H: 0001 L: D4C0

3355 (PR)

SP155 CODRH Excessive error width on C-axis (high byte)

3356 SP156 OVSH C-axis overshoot compensa- tion

Set this to prevent overshooting when shifting from movement to stopping with C-axis control. (Set this referring to the load meter display when overshooting occurred.)

0 to 1000 (0.1%)

0

3357 to

3358

SP157 to

SP158

Not used. Set to "0". 0 0

3359 SP159 CPY0 C-axis non-cutting variable excitation ratio

Set the minimum value of variable excitation ratio for non-cutting on the C-axis .

0 to 100 (%) 50

3360 SP160 CPY1 C-axis cutting variable excitation ratio

Set the minimum variable excitation ratio for cutting on the C-axis.

0 to 100 (%) 100

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 259

No. Items Details Setting range

Standard setting

3361 (PR)

SP161 IQGC0 Current loop gain magnifi- cation 1 for non-cutting on C-axis

Set the magnification of current loop gain (torque component) for C-axis non-cutting.

1 to 1000 (%)

100

3362 (PR)

SP162 IDGC0 Current loop gain magnifi- cation 2 for non-cutting on C-axis

Set the magnification of current loop gain (excitation component) for C-axis non-cutting.

1 to 1000 (%)

100

3363 (PR)

SP163 IQGC1 Current loop gain magnifi- cation 1 for cutting on C-axis

Set the magnification of current loop gain (torque component) for C-axis cutting.

1 to 1000 (%)

100

3364 (PR)

SP164 IDGC1 Current loop gain magnifi- cation 2 for cutting on C-axis

Set the magnification of current loop gain (excitation component) for C-axis cutting.

1 to 1000 (%)

100

3365 SP165 PG2C C-axis position loop gain 2

Set the second position loop gain when high-gain control is carried out for control of the C-axis. This parameter is applied to all the operation modes of C-axis control. When this function is not used, assign "0".

0 to 999 (1/s)

0

3366 SP166 PG3C C-axis position loop gain 3

Set the third position loop gain when high-gain control is carried out for control of the C-axis. This parameter is applied to all the operation modes of C-axis control. When this function is not used, assign "0".

0 to 999 (1/s)

0

3367 (PR)

SP167

PGU Position loop gain for increased spindle holding force

Set the position loop gain for when the disturbance observer is valid.

0 to 100 (1/s)

15

3368 (PR)

SP168

VGUP Speed loop gain proportional item for increased spindle holding force

Set the speed loop gain proportional item for when the disturbance observer is valid.

0 to 5000 (1/s)

63

3369 (PR)

SP169

VGUI Speed loop gain integral item for increased spindle holding force

Set the speed loop gain integral item for when the disturbance observer is valid.

0 to 5000 (0.1 1/s)

60

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 260

No. Items Details Setting range

Standard setting

3370 (PR)

SP170

VGUD Speed loop gain delay advance item for increased spindle holding force

Set the speed loop gain delay advance item for when the disturbance observer is valid.

0 to 5000 (0.1 1/s)

15

3371 to

3376

SP171 to

SP176

Not used. Set to "0". 0 0

3377 (PR)

SP177 SPECS Spindle synchronous specifica- tions

Set the spindle synchronous specifications in bit units.

0000 to FFFF HEX setting

0000

3378 (PR)

SP178 VGSP Spindle synchronous speed loop gain propor- tional term

Set the speed loop proportional gain in spindle synchronous mode.

0 to 1000 (1/s)

63

3379 (PR)

SP179 VGSI Spindle synchronous speed loop gain integral term

Set the speed loop integral gain in spindle synchronous mode.

0 to 1000 (0.1 1/s)

60

bit Name Meaning when set to 0 Meaning when set to 1 0 fclx Closed loop Semi-closed loop

1 adin Interpolation A/D compensation invalid

Interpolation A/D compensation valid

2 rtrn Position monitor during ready OFF invalid

Position monitor during ready OFF valid

3 pyfx Normal excitation Position loop excitation fixed (strong)

4

5 fdir Position detector direc- tion (positive direction)

Position detector direc- tion (negative direction)

6 7 8 9 A B C

D odx8 Magnification of

excessive error width 8 times invalid

Magnification of excessive error width 8 times valid

E F (Used with SPJ)

F E D C B A 9 8 Odx8 phos

7 6 5 4 3 2 1 0 fdir pyfx rtrn adin fclx

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 261

No. Items Details Setting range

Standard setting

3380 (PR)

SP180 VGSD Spindle synchronous speed loop gain delay advance term

Set the speed loop delay advance gain in spindle synchronous mode. When this parameter is set to "0", PI control is applied.

0 to 1000 (0.1 1/s)

15

3381 (PR)

SP181 VCGS Spindle synchronous Target value of variable speed loop proportional gain

Set the magnification of speed loop proportional gain with respect to SP178 (VGSP) at the maximum speed defined in SP017 (TSP) in spindle synchronous mode.

0 to 100 (%) 100

3382 (PR)

SP182 VCSS Spindle synchronous Change starting speed of variable speed loop proportional gain

Set the speed when the speed loop proportional gain change starts in the spindle synchronous mode.

SP182 SP017

SP178

SP178 (SP181/100)

Proportional gain

Speed

0 to 32767 (r/min)

0

3383 SP183 SYNV Spindle synchronous Sync match- ing speed

For changeover from the speed loop to the position loop in the spindle synchronous mode, set a speed command error range for output of the synchronous speed matching signal.

0 to 1000 (r/min)

20

3384 (PR)

SP184 FFCS Spindle synchronous Acceleration rate feed forward gain

Set the acceleration rate feed forward gain in the spindle synchronous mode. This parameter is used only with the SPJ2.

0 to 1000 (%)

0

3385 SP185 SINP Spindle synchronous In-position width

Set the position error range for output of the in-position signal in the spindle synchronous mode.

1 to 2880 (1/16)

16

3386 (PR)

SP186 SODR Spindle synchronous Excessive error width

Set the excessive error width in the spindle synchronous mode.

1 to 32767 ( pulse) (1 pulse =0.088)

32767

3387 (PR)

SP187 IQGS Spindle synchronous Current loop gain magnifi- cation1

Set the magnification of current loop gain (torque component) in the spindle synchronous mode.

1 to 1000 (%)

100

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 262

No. Items Details Setting range

Standard setting

3388 (PR)

SP188 IDGS Spindle synchronous Current loop gain magnifi- cation 2

Set the magnification of current loop gain (excitation component) in the spindle synchronous mode.

1 to 1000 (%)

100

3389 SP189 PG2S Spindle synchronous Position loop gain 2

Set the second position loop gain when high-gain control is carried out in the spindle synchronous mode. When this parameter function is not used, set to "0".

0 to 999 (1/s)

0

3390 SP190 PG3S Spindle synchronous Position loop gain 3

Set the third position loop gain when high-gain control is carried out in the spindle synchronous mode. When this parameter function is not used, set to "0".

0 to 999 (1/s)

0

3391

SP191 Use not possible. 0 0

3392

SP192 Not used. Set to "0". 0 0

3393 (PR)

SP193 SPECT Synchronized tapping specifications

Set the synchronized tapping specifications in bit units.

0000 to FFFF HEX setting

0000

F E D C B A 9 8 zrtn ptyp od8x phos

7 6 5 4 3 2 1 0 fdir cdir pyfx adin fclx

bit Name Meaning when set to 0 Meaning when set to 1

0 fclx Closed loop Semi-closed loop (Gear 1 : 1 only)

1 adin Interpolation A/D compensation invalid

Interpolation A/D compensation valid

2 rtrn Position monitor during ready OFF invalid

Position monitor during ready OFF valid

3 pyfx Normal excitation Position loop excitation fixed (strong)

4 cdir Command polarity (+) Command polarity (-)

5 fdir Position detector polarity (+)

Position detector polarity (-)

6 7

8 phos Normal

(no compensation) Synchronized tapping position compensation valid

9 A B C

D od8x Magnification of

excessive error width 8 times invalid

Magnification of excessive error width 8 times valid

E ptyp Position control switch

type: After zero point return

Position control switch type: After deceleration stop

F zrtn Zero point return direction: CCW

Zero point return direction: CW

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 263

No. Items Details Setting range

Standard setting

3394 (PR)

SP194 VGTP Synchronized tapping speed loop gain proportional term

Set the speed loop proportional gain in synchronized tapping mode.

0 to 1000 (1/s)

63

3395 (PR)

SP195 VGTI Synchronized tapping speed loop gain integral term

Set the speed loop integral gain in synchronized tapping mode.

0 to1000 (0.1 1/s)

60

3396 (PR)

SP196 VGTD Synchronized tapping speed loop gain delay advance term

Set the speed loop delay advance gain in synchronized tapping mode. When this parameter is set to "0", PI control is applied.

0 to 1000 (0.1 1/s)

15

3397 SP197 This is used by Mitsubishi. Set to "0" unless particularly designated.

0 0

3398 (PR)

SP198 VCGT Synchronized tapping target value of variable speed loop proportional gain

Set the magnification of speed loop proportional gain with respect to SP194 (VGTP) at the maximum motor speed defined in SP017 (TSP) in synchronized tapping mode.

0 to 100 (%)

100

3399 (PR)

SP199 VCST Synchronized tapping change starting speed of variable speed loop proportional gain

Set the speed where the speed loop proportional gain change starts during synchronized tapping.

SP199 SP017

SP194

SP194 (SP198/100)

Proportional gain

Speed

0 to 32767 (r/min)

0

3400 (PR)

SP200 FFC1 Synchronized tapping acceleration feed forward gain (gear 1)

Set the acceleration feed forward gain for selection of gear 000 during synchronized tapping. This parameter should be used when an error of relative position to Z-axis servo is large.

0 to 1000 (%)

0

3401 (PR)

SP201 FFC2 Synchronized tapping acceleration feed forward gain (gear 2)

Set the acceleration feed forward gain for selection of gear 001 during synchronized tapping.

0 to 1000 (%)

0

3402 (PR)

SP202 FFC3 Synchronized tapping acceleration feed forward gain (gear 3)

Set the acceleration feed forward gain for selection of gear 010 during synchronized tapping.

0 to 1000 (%)

0

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 264

No. Items Details Setting range

Standard setting

3403 (PR)

SP203 FFC4 Synchronized tapping acceleration feed forward gain (gear 4)

Set the acceleration feed forward gain for selection of gear 011 during synchronized tapping.

0 to 1000 (%)

0

3404 to

3413

SP204 to

SP213

Not used. Set to "0". 0 0

3414 SP214 TZRN Synchronized tapping zero point return speed

This parameter is valid when SP193 (SPECT) bitE is set to "0". Set the zero point return speed used when the speed loop changes to the position loop.

0 to 500 (r/min)

50

3415 SP215 TPDT Synchronized tapping zero point return deceleration rate

This parameter is valid when SP193 (SPECT) bitE is set to "0". Set the deceleration rate where the machine starts to decelerate when it returns to the target stop point during synchronized tapping zero point return. When the machine tends to overshoot at the stop point set a smaller value.

0 to 10000 (pulse)

1

3416 SP216 TPST Synchronized tapping zero point return shift amount

This parameter is valid when SP193 (SPECT) bitE is set to "0". Set the synchronized tapping zero point position.

0 to 4095 0

3417 SP217 TINP Synchronized tapping in-position width

Set the position error range for output of the in-position during synchronized tapping.

1 to 2880 (1/16)

16

3418 (PR)

SP218 TODR Synchronized tapping excessive error width

Set the excessive error width during synchronized tapping.

1 to 32767 (pulse) (1 pulse =0.088)

32767

3419 (PR)

SP219 IQGT Synchronized tapping current loop gain magnifi- cation 1

Set the magnification of current loop gain (torque component) during synchronized tapping.

1 to 1000 (%)

100

3420 (PR)

SP220 IDGT Synchronized tapping current loop gain magnifi- cation 2

Set the magnification of current loop gain (excitation component) during synchronized tapping.

1 to 1000 (%)

100

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 265

No. Items Details Setting range

Standard setting

3421 SP221 PG2T Synchronized tapping position loop gain 2

Set the second position loop gain when high-gain control is applied during synchronized tapping. When this parameter is not used, set to "0".

0 to 999 (1/s)

0

3422 SP222 PG3T Synchronized tapping position loop gain 3

Set the third position loop gain when high-gain control is applied during synchronized tapping. When this parameter is not used, set to "0".

0 to 999 (1/s)

0

3423 SP223 SPDV Speed monitor speed

Set the spindle limit speed in the door open state. (Invalid when 0 is set.) If the spindle end speed exceeds this setting value when the door is open, the speed monitor error (5E) will occur.

0 to 800 (r/min)

0

3424 SP224 SPDF Speed monitor time

Set the time (continuous) to detect alarms. (Detected instantly when 0 is set.)

0 to 2813 (3.5ms)

0

3425 SP225 OXKPH Position loop gain magni- fication after orientation gain changeover (H coil)

0 to 2560 (1/256-fold)

0

3426 SP226 OXKPL Position loop gain magni- fication after orientation gain changeover (L coil)

0 to 2560 (1/256-fold)

0

3427 SP227 OXVKP Speed loop proportional gain magnifi- cation after orientation gain changeover

If gain changeover is valid (SP097: SPEC0-bitC=1) during orientation, set the magnification of each gain changed to after in-position.

0 to 2560 (1/256-fold)

0

3428 SP228 OXVKI Speed loop cumulative gain magnifi- cation after orientation gain changeover

If gain changeover is valid (SP097: SPEC0-bitC=1) during orientation, set the magnification of each gain changed to after in-position.

0 to 2560 (1/256-fold)

0

3429 SP229 OXSFT Orientation virtual target shift amount

Set the amount to shift the target position when orientation virtual target position is valid (SP097: SPEC0-bitD=1).

0 to 2048 (360/4096)

0

3430 to

3432

SP230 to

SP232

Use not possible.

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 266

No. Items Details Setting range

Standard setting

3433 (PR)

SP233 JL Disturbance observer general inertia scale

Set the ratio of the motor inertia + load inertia and motor inertia.

= 100 Motor inertia + load inertia

Motor inertia

Setting value

(Normally, set "100" or more. When less than "50" is set, the setting will be invalid.)

0 to 5000 (%)

0

3434 (PR)

SP234 OBS1 Disturbance observer low path filter frequency

Set the frequency of the low path filter for when the disturbance observer is valid. Setting (1/s) = 2f

f: Approx. 1.5 times the disturbance frequency

0 to 1000 (1/s)

0

3435 (PR)

SP235 OBS2 Disturbance observer gain

Set the gain for the disturbance observer.

0 to 500 (%) 0

3436 SP236 OBS3 This is used by Mitsubishi. Set to "0" unless particularly designated.

0 0

3437

SP237 Not used. Set to "0". 0 0

3438 to

3441

SP238 to

SP241

Use not possible. 0 0

3442

SP242 Vavx 0 0

3443

SP243 UTTM 0 0

3444

SP244 OPLP 0 0

3445

SP245 PGHS 0 0

3446

SP246 TEST

This is used by Mitsubishi. Set to "0" unless particularly designated.

0 0

3447 to

3448

SP247 to

SP248

Use not possible. 0 0

3449 SP249 SM0 Speed meter speed

Set the motor rotation speed when the speed meter 10V is output. When set to "0", this parameter becomes the same as SP017 (TSP).

0 to 32767 (r/min)

0

3450 SP250 LM0 Load meter voltage

Set the voltage when the load meter 120% is output. When set to "0", this becomes 10V.

0 to 10 (V)

0

3451 to

3452

SP251 to

SP252

Use not possible. 0 0

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 267

No. Items Details Setting range

Standard setting

3453 SP253

DA1NO D/A output channel 1 data number

Set the output data number for channel 1 of the D/A output function. When set to "0", the output is speedometer. Refer to "8.5 Supplement".

-32768 to 32767

0

3454 SP254 DA2NO D/A output channel 2 data number

Set the output data number for channel 2 of the D/A output function. When set to "0", the output is load meter. Refer to "8.5 Supplement".

-32768 to 32767

0

3455 SP255 DA1MPY DA output channel 1 magnifica- tion

Set the data magnification for channel 1 of the D/A output function. The output magnification is the setting value divided by 256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "8.5 Supplement".

-32768 to 32767 (1/256-fold)

0

3456 SP256 DA2MPY DA output channel 2 magnifica- tion

Set the data magnification for channel 2 of the D/A output function. The output magnification is the setting value divided by 256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "8.5 Supplement".

-32768 to 32767 (1/256-fold)

0

3457 (PR)

to 3520 (PR)

SP257

to SP320

RPM BSD

Motor constant (H coil)

This parameter is valid only in the following two conditional cases: (a) In case that SP034 (SFNC2) bit0=1

and SP034 (SFNC2) bit2=0 Set the motor constants when using a special motor, not described in the SP040 (MTYP) explanation and when not using the coil changeover motor.

(b) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=1 Set the motor constant of the H coil of the coil changeover motor.

(Note) It is not allowed for the user to

change the setting.

0000 to FFFF HEX setting

0000

No. Items Details Setting range

Standard setting

3494 SP294 Kt Torque constant for disturbance observer

Set the torque constant for disturbance observer.

30-minute rated output 1000Setting

(0.01kgm)= Base speed 1.026 100

0000 to FFFF HEX setting

-

3495 SP295 GDM Motor inertia for disturbance observer

Set the motor inertia for disturbance observer.

Setting (0.001kgm2)=GDM 2 1000

0000 to FFFF HEX setting

-

8. Spindle Parameters 8.3 MDS-B-SP/SPH, MDS-C1-SP/SPH

II - 268

No. Items Details Setting range

Standard setting

3521 (PR)

to 3584 (PR)

SP321

to SP384

RPML BSDL

Motor constant (L coil)

This parameter is valid only in the following conditional case: (a) In case that SP034 (SFNC2) bit0=1

and SP034 (SFNC2) bit2=1 Set the motor constant of the L coil of the coil changeover motor.

(Note) It is not allowed for the user to

change the setting.

0000 to FFFF HEX setting

0000

No. Items Details Setting range

Standard setting

3558 SP358 KtL Torque constant 2 for disturbance observer

Set the torque constant for disturbance observer.

30-minute rated output 1000Setting

(0.01kgm)= Base speed 1.026 100

0000 to FFFF HEX setting

-

3559 SP359 GDML Motor inertia 2 for disturbance observer

Set the motor inertia for disturbance observer.

Setting (0.001kgm2)=GDM 2 1000

0000 to FFFF HEX setting

-

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 269

8.4 MDS-C1-SPM

The spindle parameter setting and display method will differ according to the NC being used, so refer to Instruction Manual for each NC and the following spindles.

MELDAS AC Servo and Spindle MDS-C1 Series Specifications Manual ........................ BNP-C3000

For parameters marked with a (PR) in the tables, turn the NC power OFF after setting. The parameters will be valid after the power is turned ON again. The "fixed control constants" and "fixed control bits" in this section are set by Mitsubishi.

! CAUTION

! Do not make remarkable adjustments or changes of the parameters as the operation may become unstable.

! In the explanation on bits, set all bits not used, including blank bits, to "0".

No. Items Details Setting range

Standard setting

3201 SP001 PGM Magnetic sensor and motor built-in encoder orientation position loop gain

As the set value is larger, the orientation time becomes shorter and servo rigidity is increased. However, vibration is increased and the machine becomes likely to overshoot.

0 to 2000 (0.1 1/s)

100

3202 SP002 PGE Encoder orientation position loop gain

As the set value is larger, the orientation time becomes shorter and servo rigidity is increased. However, vibration is increased and the machine becomes likely to overshoot.

0 to 2000 (0.1 1/s)

100

3203 SP003 PGC0 C-axis non-cutting position loop gain

Set the position loop gain in C-axis non-cutting mode. During non-cutting (rapid traverse, etc.) with the C axis control, this position loop gain setting is valid.

1 to 200 (1/s)

15

3204 SP004 OINP Orientation in-position width

Set the position error range in which an orientation completion signal is output.

1 to 2880 (1/16 )

16

3205 (PR)

SP005 OSP Orientation mode changing speed limit value

Set the motor speed limit value to be used when the speed loop is changed to the position loop in orientation mode. When this parameter is set to "0", SP017 (TSP) becomes the limit value.

0 to 32767 (r/min)

0

3206 SP006 CSP Orientation mode deceleration rate

As the set value is larger, the orientation time becomes shorter. However, the machine becomes likely to overshoot.

1 to 1000 20

3207 SP007 OPST In-position shift amount for orientation

Set the stop position for orientation. (i) Motor built-in encoder, encoder: Set the value by dividing 360 by 4096. (ii) Magnetic sensor: Divide -5 to +5 by 1024 and put 0 for 0.

(i) 0 to 4095 (ii) -512 to

512

0

3208

SP008 Not used. Set to "0". 0 0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 270

No. Items Details Setting range

Standard setting

3209 SP009 PGT Synchronized tapping Position loop gain

Set the spindle position loop gain in synchronized tapping mode.

1 to 200 (1/s)

15

3210 SP010 PGS Spindle synchronous position loop gain

Set the spindle position loop gain in spindle synchronization mode.

1 to 200 (1/s)

15

3211 to

3216

SP011 to

SP016

Use not possible. 0 0

3217 (PR)

SP017 TSP Maximum motor speed

Set the maximum motor speed of the spindle.

1 to 32767 (r/min)

6000

3218 (PR)

SP018 ZSP Motor zero speed

Set the motor speed for which zero-speed output is performed.

1 to 1000 (r/min)

50

3219 (PR)

SP019 CSN1 Speed cushion 1

Set the time constant for a speed command from "0" to the maximum speed. (This parameter is invalid in position loop mode.)

1 to 32767 (10ms)

30

3220 (PR)

SP020 SDTS Speed detection set value

Set the motor speed so for which speed detection output is performed. Usually, the setting value is 10% of SP017 (TSP).

0 to 32767 (r/min)

600

3221 SP021 TLM1 Torque limit 1 Set the torque limit rate for torque limit signal 001.

0 to 120 (%) 10

3222 (PR)

SP022 VGNP1 Speed loop gain proportional term under speed control

Set the speed loop proportional gain in speed control mode. When the gain is increased, response is improved but vibration and sound become larger.

0 to 1000 (1/s)

63

3223 (PR)

SP023 VGNI1 Speed loop gain integral term under speed control

Set the speed loop integral gain in speed control mode. Usually, set a value in proportion to SP022 (VGNP1).

0 to 1000 (0.1 1/s)

60

3224

SP024 Use not possible. 0 0

3225 (PR)

SP025 GRA1 Spindle gear teeth count 1

Set the number of gear teeth of the spindle corresponding to gear 000.

1 to 32767 1

3226 (PR)

SP026 GRA2 Spindle gear teeth count 2

Set the number of gear teeth of the spindle corresponding to gear 001.

1 to 32767 1

3227 (PR)

SP027 GRA3 Spindle gear teeth count 3

Set the number of gear teeth of the spindle corresponding to gear 010.

1 to 32767 1

3228 (PR)

SP028 GRA4 Spindle gear teeth count 4

Set the number of gear teeth of the spindle corresponding to gear 011.

1 to 32767 1

3229 (PR)

SP029 GRB1 Motor shaft gear teeth count 1

Set the number of gear teeth of the motor shaft corresponding to gear 000.

1 to 32767 1

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 271

No. Items Details Setting range

Standard setting

3230 (PR)

SP030 GRB2 Motor shaft gear teeth count 2

Set the number of gear teeth of the motor shaft corresponding to gear 001.

1 to 32767 1

3231 (PR)

SP031 GRB3 Motor shaft gear teeth count 3

Set the number of gear teeth of the motor shaft corresponding to gear 010.

1 to 32767 1

3232 (PR)

SP032 GRB4 Motor shaft gear teeth count 4

Set the number of gear teeth of the motor shaft corresponding to gear 011.

1 to 32767 1

3233 (PR)

SP033 SFNC1 Spindle function 1

Set the spindle function 1 in bit units.

0000 to FFFF HEX setting

0000 F E D C B A 9 8

poff ront pycal pychg

7 6 5 4 3 2 1 0 pyst pyoff

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 1 2 3 4 5 6 7 8 9 A

B This is used by Mitsubishi. Set to "0" unless particularly designated.

C ront Normal ready ON High-speed ready ON

D This is used by Mitsubishi. Set to "0" unless particularly designated.

E

F poff Contactor hold at NC power OFF invalid

Contactor hold at NC power OFF valid

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 272

No. Items Details Setting range

Standard setting

3234 (PR)

SP034 SFNC2 Spindle function 2

Set the spindle function 2 in bit units.

0000 to FFFF HEX setting

000C F E D C B A 9 8

7 6 5 4 3 2 1 0 mkc2 mkch Mk3c mts1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1

0 mts1 Special motor constant invalid

Special motor constant setting valid

1 Mk3c 3-step coil changeover function invalid

3-step coil changeover function valid

2 mkch Coil switch function invalid Coil switch function valid

3 mkc2 Coil switch specification 2 invalid

Coil switch specification 2 valid (Note1) (Note2)

4 5 6 7 8 9 A B C D E F

(Note1) To validate bit3(mkc2), NC side needs to prepare. (Note2) Always turn the bit2 at the same time to use bit3.

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 273

No. Items Details Setting range

Standard setting

3235 (PR)

SP035 SFNC3 Spindle function 3

Set the spindle function 3 in bit units.

0000 to FFFF HEX setting

0000 F E D C B A 9 8

7 6 5 4 3 2 1 0 mwid lwid hwid

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 hwid H coil output character- istics change invalid

H coil output character- istics change valid

1 lwid L coil output character- istics change invalid

L coil output character- istics change valid

2 mwid M coil output character- istics change invalid

M coil output character- istics change valid

3 4 5 6 7 8 9 A B C D E F

(Used with SPJ.)

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 274

No. Items Details Setting range

Standard setting

3236

SP036 Not used. Set to "0".

3237 (PR)

SP037 SFNC5 Spindle function 5

Set the spindle function 5 in bit units.

0000 to FFFF HEX setting

0000 F E D C B A 9 8 nsno nosg

7 6 5 4 3 2 1 0 plgo enco

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 enco Encoder orientation invalid

Encoder orientation valid

1 2 plgo PLG orientation invalid PLG orientation valid 3 4 5 6 7

8 nosg No-signal detection type

(Always monitoring) Monitoring only in position loop or orientation-mode

9 nsno No-signal detection valid

No-signal detection invalid

A B C D E F

(Note) For bit0 to 2, do not set two bits or more to "1" at the same time.

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 275

No. Items Details Setting range

Standard setting

3238 (PR)

SP038 SFNC6 Spindle function 6

Set the spindle function 6 in bit units.

0000 to FFFF HEX setting

0000 F E D C B A 9 8 XFzs pl80 sdt2

7 6 5 4 3 2 1 0

hzrn orm tdn plg2 pftm alty

(Note) Always set "0" for the empty bits. bit Name Meaning when set to 0 Meaning when set to 1

0 alty Deceleration stop during special alarm invalid

Deceleration stop during special alarm valid

1

2 pftm Encoder feedback serial communication invalid

Encoder feedback serial communication valid

3 plg2 Semi-closed pulse output signal 2 invalid

Semi-closed pulse output signal 2 valid

4 tdn Fixed control bit 5

6 orm Orientation start memo invalid

Orientation start memo valid

7 hzrn 8 sdt2 9 pl80

Fixed control bit

A B C XFzs Fixed control bit D E F

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 276

No. Items Details Setting range

Standard setting

3239 (PR)

SP039 ATYP Amplifier type

Set the amplifier type. Set each amplifier type or "0"

Parameter setting Amplifier type 0000 0001 0002 0003 0004 0005 0006 0007 SPM-110 0008 SPM-150 0009 SPM-185 000A SPM-220 000B SPM-260 000C SPM-300 000D (SPM-370) 000E (SPM-450) 000F 0010

(Note) (SPM-370) and (SPM-450) are used

with MDS-B-SPM.

0000 to FFFF HEX setting

0000

3240 (PR)

SP040 MTYP Motor type

0000 to FFFF HEX setting

0000

F E D C B A 9 8

7 6 5 4 3 2 1 0 motr

bit Name Detail 0 1 2 3 4

motr Set the motor type. Set "0" when using a special motor.

5 6 7 8 9 A B C D E F

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 277

No. Items Details Setting range

Standard setting

3241 (PR)

SP041 PTYP Power supply type

Power supply type

0000 to FFFF HEX setting

0000

3242 (PR)

SP042 CRNG C-axis detector range

This parameter is used to set the C-axis detector range. Set "0" for this parameter. "2" is used by Mitsubishi for testing.

0 to 7 0

F E D C B A 9 8 amp rtyp

7 6 5 4 3 2 1 0

ptyp

bit Explanation 0 1 2

When the CN4 connector of the drive unit and the power supply are connected, setting below is necessary. To validate the external emergency stop function, add 40h.

3 Set- ting 0x 1x 2x 3x 4x 5x 6x 7x 8x

4 x0 Not

used CV-300

5 x1 CV-110 CR-10 6 x2 CV-220 CR-15 7

ptyp

x3 CR-22 x4 CV-37 CR-37 x5 CV-150 CV-450 CV-550 x6 CV-55 CV-260 CR-55 x7 CV-370 x8 CV-75 CR-75 x9 CV-185 CR-90

8 Set the regenerative resistor type when MDS-A-CR is used.

9 Set- ting

Regenerative resistor model name

Resistance value Capacity

A 0 MDS-C1-CV (Setting when using power supply regeneration) B

rtyp

1 GZG200W260HMJ 26 80W 2 GZG300W130HMJ2 26 150W 3 MR-RB30 13 300W 4 MR-RB50 13 500W 5 GZG200W200HMJ3 6.7 350W 6 GZG300W200HMJ3 6.7 500W 7 R-UNIT-1 30 700W 8 R-UNIT-2 15 700W 9 R-UNIT-3 15 2100W A to D No setting E Large capacity + ready ON high-speed sequence F Ready ON high-speed sequence

C D E F

amp

Always set to 0.

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 278

No. Items Details Setting range

Standard setting

3243 (PR)

SP043 TRNG Synchronous tapping, spindle synchronous detector range

This parameter is used to set the synchronous tapping or spindle synchronous detector range. Set "0" for this parameter.

0 to 7 0

3244 (PR)

SP044 TRAN S

NC communi- cation frequency

Set a frequency of data communication with NC.

0 to 32767 Standard: 0 Special: 1028

3245 SP045 CSNT Dual cushion timer

Set the cycle to add the increment values in the dual cushion process. When this setting value is increased, the dual cushion will increase, and the changes in the speed during acceleration/deceleration will become gradual.

0 to 1000 (ms)

0

3246 (PR)

SP046 CSN2 Speed command dual cushion

For an acceleration/deceleration time constant defined in SP019 (CSN1) , this parameter is used to provide smooth movement only at the start of acceleration/deceleration. As the value of this parameter is smaller, it moves smoother but the acceleration/deceleration time becomes longer. To make this parameter invalid, set "0".

0 to 1000 0

3247 (PR)

SP047 SDTR Speed detection reset value

Set the reset hysteresis width for a speed detection set value defined in SP020 (SDTS).

0 to 1000 (r/min)

30

3248 (PR)

SP048 SUT Speed reach range

Set the speed deviation rate with respect to the commanded speed for output of the speed reach signal.

0 to 100 (%)

15

3249 SP049 TLM2 Torque limit 2 Set the torque limit rate for the torque limit signal 010.

1 to 120 (%)

20

3250 SP050 TLM3 Torque limit 3 Set the torque limit rate for the torque limit signal 011.

1 to 120 (%)

30

3251 SP051 TLM4 Torque limit 4 Set the torque limit rate for the torque limit signal 100.

1 to 120 (%)

40

3252 SP052 TLM5 Torque limit 5 Set the torque limit rate for the torque limit signal 101.

1 to 120 (%)

50

3253 SP053 TLM6 Torque limit 6 Set the torque limit rate for the torque limit signal 110.

1 to 120 (%)

60

3254 SP054 TLM7 Torque limit 7 Set the torque limit rate for the torque limit signal 111.

1 to 120 (%)

70

3255 (PR)

SP055 SETM Excessive speed deviation timer

Set the timer value until the excessive speed deviation alarm is output. The value of this parameter should be longer than the acceleration/deceleration time.

0 to 60 (s) 12

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 279

No. Items Details Setting range

Standard setting

3256

SP056 Use not possible. 0 0

3257 (PR)

SP057 STOD Constant excessive judgment value

Set the value for judging when changing from a constant to excessive speed command.

0 to 50 (r/min)

0

3258 (PR)

SP058 SDT2 2nd speed detection speed

Set the speed for turning the 2nd speed detection ON. (This is valid only when SP038: SFNC6-bit8 is set to "1".) If the speed drops below this set speed, the 2nd speed detection will turn ON. When the speed reaches this set speed +15r/min or more, the 2nd speed detection will turn OFF. If SP034: SFNC2-bit1 is set to "1", this will be the medium-speed and high-speed coil changeover speed. The speed detection reset width follows the SP047 (speed detection reset width) setting.

0 to 32767 (r/min)

0

3259 (PR)

SP059 MKT Winding changeover base shut-off timer

Set the base shut-off time for contactor switching at winding changeover. Note that the contactor may be damaged with burning if the value of this parameter is too small.

50 to 10000 (ms)

150

3260 (PR)

SP060 MKT2 Current limit timer after winding changeover

Set the current limit time to be taken after completion of contactor switching at winding changeover.

0 to 10000 (ms)

500

3261 (PR)

SP061 MKIL Current limit value after winding changeover

Set the current limit value during a period defined in SP060 (MKT2) after completion of contactor switching at winding changeover.

0 to 120 (%)

75

3262

SP062 Not used. Set to "0". 0 0

3263 (PR)

SP063 OLT Overload alarm detection time

Set the time constant for detection of the motor overload alarm.

0 to 1000 (s)

60

3264 (PR)

SP064 OLL Overload alarm detection level

Set the detection level of the motor overload alarm.

0 to 180 (%)

110

3265 (PR)

SP065 VCGN1 Target value of variable speed loop proportional gain

Set the magnification of speed loop proportional gain with respect to SP022 (VGNP1) at the maximum motor speed defined in SP017 (TSP).

0 to 100 (%)

100

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 280

No. Items Details Setting range

Standard setting

3266 (PR)

SP066 VCSN1 Change starting speed of variable speed loop proportional gain

Set the speed when the speed loop proportional gain change starts.

SP066 SP017

SP022

SP022 (SP065/100)

Proportional gain

Speed

0 to 32767 (r/min)

0

3267 (PR)

SP067 VIGWA Change starting speed of variable current loop gain

Set the speed where the current loop gain change starts.

0 to 32767 (r/min)

0

3268 (PR)

SP068 VIGWB Change ending speed of variable current loop gain

Set the speed where the current loop gain change ends.

0 to 32767 (r/min)

0

3269 (PR)

SP069 VIGN Target value of variable current loop gain

Set the magnification of current loop gain (torque component and excitation component) for a change ending speed defined in SP068 (VIGWB). When this parameter is set to "0", the magnification is 1.

SP067 SP017SP068

Speed

Gain

SP069(1/16)-fold

1-fold

0 to 32767 (1/16-fold)

0

3270 SP070 FHz Machine resonance suppression filter frequency

When machine vibration occurs in speed and position control, set the frequency of the required vibration suppression. Note that a value of 100Hz or more is set. Set to "0" when not used.

0 to 3000 (Hz)

0

3271 to

3275

SP071 to

SP075

Use not possible. 0 0

SP017 (TSP) Maximum

motor speed

SP067 (VIGWA)

SP068 (VIGWB)

SP069 (VIGN)

0 to 6000 0 0 0 6001 to 8000 5000 8000 45 8001 or more 5000 10000 64

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 281

No. Items Details Setting range

Standard setting

3276 SP076 FONS Machine resonance suppression filter operation speed

When the vibration increases in motor stop (ex. in orientation stop) when the machine vibration suppression filter is operated by SP070, operate the machine vibration suppression filter at a speed of this parameter or more. When set to "0", this is validated for all speeds.

0 to 32767 (r/min)

0

3277 (PR)

SP077 TDSL Fixed control constant

Set by Mitsubishi. Set "14" unless designated in particular.

14

3278 (PR)

SP078 FPWM Fixed control constant

Set by Mitsubishi. Set "1" unless designated in particular.

1 1

3279

SP079 Use not possible. 0 0

3280 SP080 SWTD Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

3281 to

3286

SP081 to

SP086

Use not possible. 0 0

3287 (PR)

SP087 DIQM Target value of variable torque limit magnifica- tion at deceleration

Set the minimum value of variable torque limit at deceleration.

0 to 150 (%)

75

3288 (PR)

SP088 DIQN Speed for starting change of variable torque limit magnifica- tion at deceleration

Set the speed where the torque limit value at deceleration starts to change.

SP088 SP017

100%

SP087

Torque limit

Speed

Inversely proportional to speed

0 to 32767 (r/min)

3000

3289 to

3292

SP089 to

SP092

Use not possible. 0 0

3293 (PR)

SP093 ORE Tolerable pulse check error

Set this when detecting the pulse detector's pulse mistakes. (Valid only for full close control.)

0 to 32767 0

3294 (PR)

SP094 LMAV Load meter output filter

Set the filter time constant of load meter output. When "0" is set, a filter time constant is set to 100ms.

0 to 32767 (2ms)

0

3295 (PR)

SP095 VFAV Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

0 0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 282

No. Items Details Setting range

Standard setting

3296 (PR)

SP096 EGAR Encoder gear ratio

Set the gear ratio between the spindle end and the encoder end (except for the motor-built-in encoder) as indicated below.

Setting value

Gear ratio (deceleration)

0 1 : 1 1 1 : 2 2 1 : 4 3 1 : 8 4 1 : 16

(Note) Use a combination so that the encoder

end is slower than the spindle end.

0 to 4 0

3297 (PR)

SP097 SPECO Orientation specifica- tion

Set the orientation specifications in bit units.

0000 to FFFF HEX setting

0000 F E D C B A 9 8

ostp orze ksft gchg ips2

7 6 5 4 3 2 1 0 vg8x fdir osc1 dmin odi2 odi1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 odi1

1

odi2 Orientation rotation direction 00: Previous (the direction in which the motor has

so far rotated under speed control) 01: Forward rotation 10: Backward rotation 11: Prohibited (Same as setting value = 10)

2 dmin Orientation in-position advance invalid

Orientation in-position advance valid

3

4 osc1 Indexing speed clamp invalid

Indexing speed clamp valid

5 fdir Encoder detector polarity: +

Encoder detector polarity:

6

7 vg8x Speed gain *1/8 during torque limit valid

Speed gain *1/8 during torque limit invalid

8 9 A ips2 2nd in-position invalid 2nd in-position valid B

C gchg Gain changeover during orientation invalid

Gain changeover during orientation valid

D ksft Orientation virtual target shift invalid

Orientation virtual target shift valid

E orze F ostp

This is used by Mitsubishi. Set to "0" unless particularly designated.

In-position advance (bit 2) 0 (invalid) 1 (valid)

0 (Invalid)

In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=0

S ec

on d

in -p

os iti

on

1 (Valid)

In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=1

In-position signal in DINP width=1 Control output 4/ bit 4=1 Second in-position signal in OINP width = 0 Control output 4/ bit F=1

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 283

No. Items Details Setting range

Standard setting

3298 (PR)

SP098 VGOP Speed loop gain propor- tional term in orientation mode

Set the speed loop proportional gain in orientation mode. When the gain is increased, rigidity is improved in the orientation stop but vibration and sound become larger.

0 to 2000 (1/s)

63

3299 (PR)

SP099 VGOI Orientation mode speed loop gain integral term

Set the speed loop integral gain in orientation mode.

0 to 2000 (0.1 1/s)

60

3300 (PR)

SP100 VGOD Orientation mode speed loop gain delay advance term

Set a loop gain delay advance gain in orientation mode. When this parameter is set to "0", PI control is applied.

0 to 1000 (0.1 1/s)

15

3301 (PR)

SP101 DINP Orientation advance in-position width

When using the orientation in-position advance function, set the in-position width that is larger than the normal in-position width defined in SP004 (OINP).

1 to 2880 (1/16)

16

3302 (PR)

SP102 OODR Excessive error value in orientation mode

Set the excessive error width in orientation mode.

0 to 32767 (1/4 pulse) (1 pulse= 0.088)

32767

3303 (PR)

SP103 FTM Index positioning completion OFF time timer

Set the time for forcedly turn OFF the index positioning completion signal (different from the orientation completion signal) after the leading edge of the indexing start signal.

0 to 10000 (ms)

200

3304 (PR)

SP104 TLOR Torque limit value for orientation servo locking

Set the torque limit value for orientation in-position output. If the external torque limit signal is input, the torque limit value set by this parameter is made invalid.

0 to 120 (%)

100

3305 (PR)

SP105 IQG0 Current loop gain magnifica- tion 1 in orientation mode

Set the magnification for current loop gain (torque component) at orientation completion.

1 to 1000 (%)

100

3306 (PR)

SP106 IDG0 Current loop gain magnifica- tion 2 in orientation mode

Set the magnification for current loop gain (excitation component) at orientation completion.

1 to 1000 (%)

100

3307 SP107 CSP2 Deceleration rate 2 in orientation mode

Set the deceleration rate in orientation mode corresponding to the gear 001. When this parameter is set to "0", same as SP006 (CSP).

0 to 1000 0

3308 SP108 CSP3 Deceleration rate 3 in orientation mode

Set the deceleration rate in orientation mode corresponding to the gear 010. When this parameter is set to "0", same as SP006 (CSP).

0 to 1000 0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 284

No. Items Details Setting range

Standard setting

3309 SP109 CSP4 Deceleration rate 4 in orientation mode

Set the deceleration rate in orientation mode corresponding to the gear 011. When this parameter is set to "0", same as SP006 (CSP).

0 to 1000 0

3310 to

3313

SP110 to

SP003

Use not possible. 0

3314 SP114 OPER Orientation pulse miss check value

An alarm "5C" will occur if the pulse miss value at the orientation stop exceeds this setting value. (Note that this is invalid when set to "0".) In this parameter, set the value to fulfill the following conditions. SP114 setting value > 1.5 SP004 (orientation in-position width)

0 to 32767 (360/4096)

0

3315 SP115 OSP2 Orientation motor speed clamp value 2

When the orientation clamp speed is changed by the control input, this parameter setting will be used instead of SP005: OSP. Indexing speed clamp valid This parameter is used when (SP097: SPEC0-bit4 = 1).

0 to 32767 (r/min)

0

3316

SP116 Use not possible. 0 0

3317 SP117 ORUT Set by Mitsubishi. Set "0" unless designated in particular.

0 0

3318 SP118 ORCT Number of orientation retry times

Set the number of times to retry when an orientation or feedback error occurs. The warning (A9) is issued while retrying orientation, and an alarm (5C) is issued when the set number of times is exceeded.

0 to 100 (time)

0

3319 SP119 MPGH Orientation position gain H winding compensa- tion magnifi- cation

Set the compensation magnification of the orientation position loop gain for the H winding. H winding orientation position loop gain = SP001 (or SP002) SP119/256 When set to "0", will become the same as SP001 or SP002.

0 to 2560 (1/256-fold)

0

3320 SP120 MPGL Orientation position gain L winding compensa- tion magnifi- cation

Set the compensation magnification of the orientation position loop gain for the L winding. L winding orientation position loop gain = SP001 (or SP002) SP120/256 When set to "0", will become the same as SP001 or SP002.

0 to 2560 (1/256-fold)

0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 285

No. Items Details Setting range

Standard setting

3321 SP121 MPCSH Orientation deceleration rate H winding compensa- tion magnifi- cation

Set the compensation magnification of the orientation deceleration rate for the H winding. Orientation deceleration rate for the H winding = SP006 SP121/256 When set to "0", will become the same as SP006.

0 to 2560 (1/256-fol d)

0

3322 SP122 MPCSL Orientation deceleration rate L winding compensa- tion magnifi- cation

Set the compensation magnification of the orientation deceleration rate for the L winding. Orientation deceleration rate for the L winding = SP006 SP122/256 When set to "0", will become the same as SP006.

0 to 2560 (1/256-fol d)

0

3323 to

3325

SP123 to

SP125

Use not possible. 0 0

3326 SP126 MPGH Orientation position gain M coil com- pensation

Set this to set the orientation position loop gain for the coil changeover motor to the M coil's unique value.

0 to 2560 (1/256- fold)

0

3327 SP127 MPCSM Orientation deceleration rate M coil compensa- tion

Set this to set the orientation deceleration rate for the coil motor to the M coil's unique value.

0 to 2560 (1/256- fold)

0

3328 SP128 OXKPM Position loop gain magnifi- cation after orientation gain change- over (M coil)

Set the M coil gain magnification to be used after in-position when gain changeover is valid (SP097: SPEC0-bitC=1) during orientation.

0 to 2560 (1/256- fold)

0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 286

No. Items Details Setting range

Standard setting

3329 (PR)

SP129 SPECC C-axis specifica- tions

Set the C-axis specifications in bit units.

0000

3330 SP130 PGC1 First position loop gain for cutting on C-axis

Set the position loop gain when the first gain is selected for C axis cutting.

1 to 200 (1/s)

15

F E D C B A 9 8 zrtn ptyp fb9x zrtd zrn2 zdir ztyp

7 6 5 4 3 2 1 0

vg8x fdir phos rtrn fclx

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1

0 fclx Closed loop Semi-closed loop (Gear 1 : 1 only)

1

2 rtrn Position monitor during ready OFF invalid

Position monitor during ready OFF valid

3 phos Normal (no compensation)

Vx4 synchronization compensation valid

4

5 fdir Position detector polarity (+)

Position detector polarity ()

6

7 vg8x Speed gain 1/8 during torque limit valid

Speed gain 1/8 during torque limit invalid

8 ztyp Z-phase type: Normal start up

Z-phase type: Start up only

9 zdir Z-phase rising polarity (+)

Z-phase rising polarity ()

A B zrn2 C zrtd

This is used by Mitsubishi. Set to "0" unless particularly designated.

D fb9x Speed feedback Standard (PLG)

Speed feedback 90,000 pulse detector

E ptyp Position control switch

type: After zero point return

Position control switch type: After deceleration stop

F zrtn Zero point return direction: CCW

Zero point return direction: CW

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 287

No. Items Details Setting range

Standard setting

3331 SP131 PGC2 Second position loop gain for cutting on C-axis

Set the position loop gain when the second gain is selected for C axis cutting.

1 to 200 (1/s)

15

3332 SP132 PGC3 Third position loop gain for cutting on C-axis

Set the position loop gain when the third gain is selected for C-axis cutting.

1 to 200 (1/s)

15

3333 SP133 PGC4 Stop position loop gain for cutting on C-axis

Set the position loop gain for stopping when carrying out C-axis cutting.

1 to 200 (1/s)

15

3334 (PR)

SP134 VGCP0 C-axis non-cutting speed loop gain proportional item

Set the speed loop proportional gain in C-axis non-cutting mode.

0 to 5000 (1/s)

63

3335 (PR)

SP135 VGCI0 C-axis non-cutting speed loop gain integral item

Set the speed loop integral gain in C-axis non-cutting mode.

0 to 5000 (0.1 1/s)

60

3336 (PR)

SP136 VGCD0 C-axis non-cutting speed loop gain delay advance item

Set the speed loop delay advance gain in C-axis non-cutting mode. When this parameter is set to "0", PI control is exercised.

0 to 5000 (0.1 1/s)

15

3337 (PR)

SP137 VGCP1 First speed loop gain proportional item for C-axis cutting

Set the speed loop proportional gain when the first gain is selected for C-axis cutting.

0 to 5000 (1/s)

63

3338 (PR)

SP138 VGCI1 First speed loop gain integral item for cutting on C-axis

Set the speed loop integral gain when the first gain is selected for C-axis cutting.

0 to 5000 (0.1 1/s)

60

3339 (PR)

SP139 VGCD1 First speed loop gain delay advance item for cutting on C-axis

Set the speed loop delay advance gain when the first gain is selected for curing on the C-axis. When this parameter is set to "0", PI control is applied.

0 to 5000 (0.1 1/s)

15

3340 (PR)

SP140 VGCP2 Second speed loop gain proportional item for cutting on C-axis

Set the speed loop proportional gain when the second gain is selected for C-axis cutting.

0 to 5000 (1/s)

63

3341 (PR)

SP141 VGCI2 Second speed loop gain integral item for cutting on C-axis

Set the speed loop integral gain when the second gain is selected for C-axis cutting.

0 to 5000 (0.1 1/s)

60

3342 (PR)

SP142 VGCD2 Second speed loop gain delay advance item for cutting on C-axis

Set the speed loop delay advance gain when the second gain is selected for C-axis cutting. When this parameter is set to "0", PI control is applied.

0 to 5000 (0.1 1/s)

15

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 288

No. Items Details Setting range

Standard setting

3343 (PR)

SP143 VGCP3 Third speed loop gain proportional item for cutting on C-axis

Set the speed loop proportional gain when the third gain is selected for C-axis cutting.

0 to 5000 (1/s)

63

3344 (PR)

SP144 VGCI3 Third speed loop gain integral item for cutting on C-axis

Set the speed loop integral gain when the third gain is selected for C-axis cutting.

0 to 5000 (0.1 1/s)

60

3345 (PR)

SP145 VGCD3 Third speed loop gain delay advance item for cutting on C-axis

Set the speed loop delay advance gain when the third gain is selected for C-axis cutting. When this parameter is set to "0", PI control is applied.

0 to 5000 (0.1 1/s)

15

3346 (PR)

SP146 VGCP4 Speed loop gain propor- tional item for stop of cutting on C-axis

Set the speed loop proportional gain when C-axis cutting is stopped.

0 to 5000 (1/s)

63

3347 (PR)

SP147 VGCI4 Speed loop gain integral item for stop of cutting on C-axis

Set the speed loop integral gain when C-axis cutting is stopped.

0 to 5000 (0.1 1/s)

60

3348 (PR)

SP148 VGCD4 Speed loop gain delay advance item for stop of cutting on C-axis

Set the speed loop delay advance gain when C-axis cutting is stopped. When this parameter is set to "0", PI control is applied.

0 to 5000 (0.1 1/s)

15

3349 SP149 CZRN C-axis zero point return speed

This parameter is valid when SP129 (SPECC) bitE is set to "0". Set the zero point return speed used when the speed loop changes to the position loop.

1 to 500 (r/min)

50

3350 SP150 CPDT C-axis zero point return deceleration point

This parameter is valid when SP129 (SPECC) bitE is set to "0". Set the deceleration rate where the machine starts to decelerate when it returns to the target stop point during C-axis zero point return. When the machine tends to overshoot at the stop point, set the smaller value.

1 to 10000 1

3351 SP151 CPSTL C-axis zero point return shift amount (low byte)

3352 SP152 CPSTH C-axis zero point return shift amount (high byte)

This parameter is valid when SPECC (SP129) bitE is set to "0". Set the C-axis zero point position.

HEX setting 00000000 to FFFFFFFF (1/1000)

H: 0000 L: 0000

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 289

No. Items Details Setting range

Standard setting

3353 SP153 CINP C-axis in-position width

Set the position error range in which the in-position signal is output on the C-axis.

0000 to FFFF (1/1000) HEX setting

03E8

3354 (PR)

SP154 CODRL Excessive error width on C-axis (low byte)

3355 (PR)

SP155 CODRH Excessive error width on C-axis (high byte)

Set the excessive error width on the C-axis.

HEX setting 00000000 to FFFFFFFF (1/1000)

H: 0001 L: D4C0

3356 SP156 OVSH C-axis overshoot compensa- tion

Set this to prevent overshooting when shifting from movement to stopping with C-axis control. (Set this referring to the load meter display when overshooting occurred.)

0 to 1000 (0.1%)

0

3357

SP157

Not used. Set to "0". 0 0

3358

SP158 Not used. Set to "0". 0 0

3359

SP159 Use not possible. 0 0

3360

SP160 Use not possible. 0 0

3361 (PR)

SP161 IQGC0 Current loop gain magnifi- cation 1 for non-cutting on C-axis

Set the magnification of current loop gain (torque component) for C-axis non-cutting.

1 to 1000 (%)

100

3362 (PR)

SP162 IDGC0 Current loop gain magnifi- cation 2 for non-cutting on C-axis

Set the magnification of current loop gain (excitation component) for C-axis non-cutting.

1 to 1000 (%)

100

3363 (PR)

SP163 IQGC1 Current loop gain magnifi- cation 1 for cutting on C-axis

Set the magnification of current loop gain (torque component) for C-axis cutting.

1 to 1000 (%)

100

3364 (PR)

SP164 IDGC1 Current loop gain magnifi- cation 2 for cutting on C-axis

Set the magnification of current loop gain (excitation component) for C-axis cutting.

1 to 1000 (%)

100

3365 SP165 PG2C C-axis position loop gain 2

Set the second position loop gain when high-gain control is carried out for control of the C-axis. This parameter is applied to all the operation modes of C-axis control. When this function is not used, assign "0".

0 to 999 (1/s)

0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 290

No. Items Details Setting range

Standard setting

3366 SP166 PG3C C-axis position loop gain 3

Set the third position loop gain when high-gain control is carried out for control of the C-axis. This parameter is applied to all the operation modes of C-axis control. When this function is not used, assign "0".

0 to 999 (1/s)

0

3367 (PR)

SP167

PGU Position loop gain for increased spindle holding force

Set the position loop gain for when the disturbance observer is valid.

0 to 100 (1/s)

15

3368 (PR)

SP168

VGUP Speed loop gain proportional item for increased spindle holding force

Set the speed loop gain proportional item for when the disturbance observer is valid.

0 to 5000 (1/s)

63

3369 (PR)

SP169

VGUI Speed loop gain integral item for increased spindle holding force

Set the speed loop gain integral item for when the disturbance observer is valid.

0 to 5000 (0.1 1/s)

60

3370 (PR)

SP170

VGUD Speed loop gain delay advance item for increased spindle holding force

Set the speed loop gain delay advance item for when the disturbance observer is valid.

0 to 5000 (0.1 1/s)

15

3371 to

3376

SP171 to

SP176

Not used. Set to "0". 0 0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 291

No. Items Details Setting range

Standard setting

3377 (PR)

SP177 SPECS Spindle synchronous specifica- tions

Set the spindle synchronous specifications in bit units.

0000 to FFFF HEX setting

0000

3378 (PR)

SP178 VGSP Spindle synchronous speed loop gain propor- tional term

Set the speed loop proportional gain in spindle synchronous mode.

0 to 2000 (1/s)

63

3379 (PR)

SP179 VGSI Spindle synchronous speed loop gain integral term

Set the speed loop integral gain in spindle synchronous mode.

0 to 2000 (0.1 1/s)

60

3380 (PR)

SP180 VGSD Spindle synchronous speed loop gain delay advance term

Set the speed loop delay advance gain in spindle synchronous mode. When this parameter is set to "0", PI control is applied.

0 to 1000 (0.1 1/s)

15

3381 (PR)

SP181 VCGS Spindle synchronous Target value of variable speed loop proportional gain

Set the magnification of speed loop proportional gain with respect to SP178 (VGSP) at the maximum speed defined in SP017 (TSP) in spindle synchronous mode.

0 to 100 (%)

100

bit Name Meaning when set to 0 Meaning when set to 1 0 fclx Closed loop Semi-closed loop 1 2

3 mach Automatic coil change-

over during spindle synchronization invalid

Automatic coil change- over during spindle synchronization valid

4

5 fdir Position detector direc- tion (positive direction)

Position detector direc- tion (negative direction)

6 7 8 9 A B C

D odx8 Magnification of

excessive error width 8 times invalid

Magnification of excessive error width 8 times valid

E F (Used with SPJ)

F E D C B A 9 8 odx8 phos

7 6 5 4 3 2 1 0 fdir mach fclx

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 292

No. Items Details Setting range

Standard setting

3382 (PR)

SP182 VCSS Spindle synchronous Change starting speed of variable speed loop proportional gain

Set the speed when the speed loop proportional gain change starts in the spindle synchronous mode.

SP182 SP017

SP178

SP178 (SP181/100)

Proportional gain

Speed

0 to 32767 (r/min)

0

3383 SP183 SYNV Spindle synchronous Sync match- ing speed

For changeover from the speed loop to the position loop in the spindle synchronous mode, set a speed command error range for output of the synchronous speed matching signal.

0 to 1000 (r/min)

20

3384 (PR)

SP184 FFCS Spindle synchronous Acceleration rate feed forward gain

Set the acceleration rate feed forward gain in the spindle synchronous mode. This parameter is used only with the SPJ2.

0 to 1000 (%)

0

3385 SP185 SINP Spindle synchronous In-position width

Set the position error range for output of the in-position signal in the spindle synchronous mode.

1 to 2880 (1/16)

16

3386 (PR)

SP186 SODR Spindle synchronous Excessive error width

Set the excessive error width in the spindle synchronous mode.

1 to 32767 ( pulse) (1 pulse =0.088)

32767

3387 (PR)

SP187 IQGS Spindle synchronous Current loop gain magnifi- cation1

Set the magnification of current loop gain (torque component) in the spindle synchronous mode.

1 to 1000 (%)

100

3388 (PR)

SP188 IDGS Spindle synchronous Current loop gain magnifi- cation 2

Set the magnification of current loop gain (excitation component) in the spindle synchronous mode.

1 to 1000 (%)

100

3389 SP189 PG2S Spindle synchronous Position loop gain 2

Set the second position loop gain when high-gain control is carried out in the spindle synchronous mode. When this parameter function is not used, set to "0".

0 to 999 (1/s)

0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 293

No. Items Details Setting range

Standard setting

3390 SP190 PG3S Spindle synchronous Position loop gain 3

Set the third position loop gain when high-gain control is carried out in the spindle synchronous mode. When this parameter function is not used, set to "0".

0 to 999 (1/s)

0

3391

SP191 Use not possible. 0 0

3392

SP192 Not used. Set to "0".

3393 (PR)

SP193 SPECT Synchronized tapping specifications

Set the synchronized tapping specifications in bit units.

0000 to FFFF HEX setting

0000

F E D C B A 9 8 zrtn ptyp od8x phos

7 6 5 4 3 2 1 0 fdir cdir pyfx rtrn fclx

bit Name Meaning when set to 0 Meaning when set to 1

0 fclx Closed loop Semi-closed loop (Gear 1 : 1 only)

1

2 rtrn Position monitor during ready OFF invalid

Position monitor during ready OFF valid

3 4 cdir Command polarity (+) Command polarity ()

5 fdir Position detector polarity (+)

Position detector polarity ()

6 7

8

phos Normal (no compensation)

Synchronized tapping position command compensation (for synchronization with high-gain servo)

9 A B C

D od8x Magnification of

excessive error width 8 times invalid

Magnification of excessive error width 8 times valid

E ptyp Position control switch

type: After zero point return

Position control switch type: After deceleration stop

F zrtn Zero point return direction: CCW

Zero point return direction: CW

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 294

No. Items Details Setting range

Standard setting

3394 (PR)

SP194 VGTP Synchronized tapping speed loop gain proportional term

Set the speed loop proportional gain in synchronized tapping mode.

0 to 2000 (1/s)

63

3395 (PR)

SP195 VGTI Synchronized tapping speed loop gain integral term

Set the speed loop integral gain in synchronized tapping mode.

0 to2000 (0.1 1/s)

60

3396 (PR)

SP196 VGTD Synchronized tapping speed loop gain delay advance term

Set the speed loop delay advance gain in synchronized tapping mode. When this parameter is set to "0", PI control is applied.

0 to 1000 (0.1 1/s)

15

3397

SP197 Use not possible. 0 0

3398 (PR)

SP198 VCGT Synchronized tapping target value of variable speed loop proportional gain

Set the magnification of speed loop proportional gain with respect to SP194 (VGTP) at the maximum motor speed defined in SP017 (TSP) in synchronized tapping mode.

0 to 100 (%)

100

3399 (PR)

SP199 VCST Synchronized tapping change starting speed of variable speed loop proportional gain

Set the speed where the speed loop proportional gain change starts during synchronized tapping.

SP199 SP017

SP194

SP194 (SP198/100)

Proportional gain

Speed

0 to 32767 (r/min)

0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 295

No. Items Details Setting range

Standard setting

3400 (PR)

SP200 FFC1 Synchronized tapping acceleration feed forward gain (gear 1)

Set the acceleration feed forward gain for selection of gear 000 during synchronized tapping. This parameter should be used when an error of relative position to Z-axis servo is large.

0 to 1000 (%)

0

3401 (PR)

SP201 FFC2 Synchronized tapping acceleration feed forward gain (gear 2)

Set the acceleration feed forward gain for selection of gear 001 during synchronized tapping.

0 to 1000 (%)

0

3402 (PR)

SP202 FFC3 Synchronized tapping acceleration feed forward gain (gear 3)

Set the acceleration feed forward gain for selection of gear 010 during synchronized tapping.

0 to 1000 (%)

0

3403 (PR)

SP203 FFC4 Synchronized tapping acceleration feed forward gain (gear 4)

Set the acceleration feed forward gain for selection of gear 011 during synchronized tapping.

0 to 1000 (%)

0

3404

SP204

3405

SP205

Fixed control constant

This is used by Mitsubishi. Set to "0" unless particularly designated.

0 0

3406 SP206 GCK Reverse run detection error detection width

When the motor moves (including movement with external force), the motor overrun alarm (3E) will be detected even if the speed command is 0 (including position control stop command) during servo ON (gate ON). Set the movement amount to be detected as an alarm. 0: Detect with 10 motor movement amount

(Recommended setting) 1: Detect with 20 motor movement amount 2: Detect with 40 motor movement amount

0/1/2 0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 296

No. Items Details Setting range

Standard setting

3407 SP207 GDL Sequential mode startup timing

To carry out spindle synchronization or C-axis control in the both-chuck state with no movement immediately after the power is turned ON, set this parameter so that the reverse run detection function will function correctly. Set so that servo ON timing for the opposing spindle has the combination of (1) and (2) shown in the drawing below. 0: Servo turns ON simultaneously with servo

ON command, and servo ON status is returned immediately.

1: Gate turns ON at pattern (1) shown below, and servo ON status is returned two seconds later.

2: Gate turns ON at pattern (2) shown below, and servo ON status is returned two seconds later.

0/1/2 0

Servo ON command

Servo ON (1)

Servo ON (2)

Servo ON status

700ms 300ms

700ms

300ms

2s

Gate ON

Servo ON

Gate ON

3408 SP208 W2 This is used by Mitsubishi.

Set to "0" unless particularly designated. 0 0

3409 to

3413

SP209 to

SP213

Not used. Set to "0". 0 0

3414 SP214 TZRN Synchronized tapping zero point return speed

This parameter is valid when SP193 (SPECT) bitE is set to "0". Set the zero point return speed used when the speed loop changes to the position loop.

3415 SP215 TPDT Synchronized tapping zero point return deceleration rate

This parameter is valid when SP193 (SPECT) bitE is set to "0". Set the deceleration rate where the machine starts to decelerate when it returns to the target stop point during synchronized tapping zero point return. When the machine tends to overshoot at the stop point set a smaller value.

0 to 10000 (pulse)

1

3416 SP216 TPST Synchronized tapping zero point return shift amount

This parameter is valid when SP193 (SPECT) bitE is set to "0". Set the synchronized tapping zero point position.

0 to 4095 0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 297

No. Items Details Setting range

Standard setting

3417 SP217 TINP Synchronized tapping in-position width

Set the position error range for output of the in-position during synchronized tapping.

1 to 2880 (1/16)

16

3418 (PR)

SP218 TODR Synchronized tapping excessive error width

Set the excessive error width during synchronized tapping.

1 to 32767 (pulse) (1 pulse =0.088)

32767

3419 (PR)

SP219 IQGT Synchronized tapping current loop gain magnifi- cation 1

Set the magnification of current loop gain (torque component) during synchronized tapping.

1 to 1000 (%)

100

3420 (PR)

SP220 IDGT Synchronized tapping current loop gain magnifi- cation 2

Set the magnification of current loop gain (excitation component) during synchronized tapping.

1 to 1000 (%)

100

3421 SP221 PG2T Synchronized tapping position loop gain 2

Set the second position loop gain when high-gain control is applied during synchronized tapping. When this parameter is not used, set to "0".

0 to 999 (1/s)

0

3422 SP222 PG3T Synchronized tapping position loop gain 3

Set the third position loop gain when high-gain control is applied during synchronized tapping. When this parameter is not used, set to "0".

0 to 999 (1/s)

0

3423 SP223 SPDV Speed monitor speed

Set the spindle limit speed in the door open state. (Invalid when 0 is set.) If the spindle end speed exceeds this setting value when the door is open, the speed monitor error (5E) will occur.

0 to 800 (r/min)

0

3424 SP224 SPDF Speed monitor time

Set the time (continuous) to detect alarms. (Detected instantly when 0 is set.)

0 to 2813 (3.5ms)

0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 298

No. Items Details Setting range

Standard setting

3425 SP225 OXKPH Position loop gain magni- fication after orientation gain changeover (H coil)

0 to 2560 (1/256-fold)

0

3426 SP226 OXKPL Position loop gain magni- fication after orientation gain changeover (L coil)

0 to 2560 (1/256-fold)

0

3427 SP227 OXVKP Speed loop proportional gain magnifi- cation after orientation gain changeover

If gain changeover is valid (SP097: SPEC0-bitC=1) during orientation, set the magnification of each gain changed to after in-position.

0 to 2560 (1/256-fold)

0

3428 SP228 OXVKI Speed loop cumulative gain magnifi- cation after orientation gain changeover

If gain changeover is valid (SP097: SPEC0-bitC=1) during orientation, set the magnification of each gain changed to after in-position.

0 to 2560 (1/256-fold)

0

3429 SP229 OXSFT Orientation virtual target shift amount

Set the amount to shift the target position when orientation virtual target position is valid (SP097: SPEC0-bitD=1).

0 to 2048 (360/4096)

0

3430 to

3432

SP230 to

SP232

Use not possible.

3433 (PR)

SP233 JL Disturbance observer general inertia scale

Set the ratio of the motor inertia + load inertia and motor inertia.

= 100 Motor inertia + load inertia

Motor inertia

Setting value

(Normally, set "100" or more. When less than "50" is set, the setting will be invalid.) To calculate speed loop gain with general inertia scale:

The effective proportional gain and effective cumulative gain during the speed control are changed at the set scale.

0 to 5000 (%)

0

3434 (PR)

SP234 OBS1 Disturbance observer low path filter frequency

Set the frequency of the low path filter for when the disturbance observer is valid. Setting (1/s) = 2f

f: Approx. 1.5 times the disturbance frequency

0 to 1000 (1/s)

0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 299

No. Items Details Setting range

Standard setting

3435 (PR)

SP235 OBS2 Disturbance observer gain

Set the gain for the disturbance observer. 0 to 500 (%) 0

3436 SP236 OBS3 Fixed control constant

This is used by Mitsubishi. Set to "0" unless particularly designated.

0 0

3437

SP237 KSCP

3438

SP238 SEZR

3439

SP239 SEZT

Fixed control constant

This is used by Mitsubishi. Set to "0" unless particularly designated.

0 0

3440

SP240 Use not possible. 0 0

3441

SP241 Use not possible. 0 0

3442

SP242 Vavx 0 0

3443

SP243 UTTM

This is used by Mitsubishi. Set to "0" unless particularly designated.

0 0

3444

SP244 OPLP Use not possible. 0 0

3445

SP245 PGHS 0 0

3446

SP246 TEST

This is used by Mitsubishi. Set to "0" unless particularly designated. 0 0

3447 to

3448

SP247 to

SP248

Use not possible. 0 0

3449 SP249 SM0 Speed meter speed

Set the motor rotation speed when the speed meter 10V is output. When set to "0", this parameter becomes the same as SP017 (TSP).

0 to 32767 (r/min)

0

3450 SP250 LM0 Load meter voltage

Set the voltage when the load meter 120% is output. When set to "0", this becomes 10V.

0 to 10 (V)

0

3451 to

3452

SP251 to

SP252

Use not possible. 0 0

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 300

No. Items Details Setting range

Standard setting

3453 SP253

DA1NO D/A output channel 1 data number

Set the output data number for channel 1 of the D/A output function. When set to "0", the output is speedometer. Refer to "8.5 Supplement".

-32768 to 32767

0

3454 SP254 DA2NO D/A output channel 2 data number

Set the output data number for channel 2 of the D/A output function. When set to "0", the output is load meter. Refer to "8.5 Supplement".

-32768 to 32767

0

3455 SP255 DA1MPY DA output channel 1 magnifica- tion

Set the data magnification for channel 1 of the D/A output function. The output magnification is the setting value divided by 256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "8.5 Supplement".

-32768 to 32767 (1/256-fold)

0

3456 SP256 DA2MPY DA output channel 2 magnifica- tion

Set the data magnification for channel 2 of the D/A output function. The output magnification is the setting value divided by 256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "8.5 Supplement".

-32768 to 32767 (1/256-fold)

0

3457 (PR)

to 3520 (PR)

SP257

to SP320

RPM BSD

Motor constant (H coil)

This parameter is valid only in the following two conditional cases: (a) In case that SP034 (SFNC2) bit0=1

and SP034 (SFNC2) bit2=0 Set the motor constants when using a special motor, not described in the SP040 (MTYP) explanation and when not using the coil changeover motor.

(b) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=1 Set the motor constant of the H coil of the coil changeover motor.

(Note) It is not allowed for the user to

change the setting.

0000 to FFFF HEX setting

0000

No. Items Details Setting range

Standard setting

3494 SP294 Kt Torque constant for disturbance observer

Set the torque constant for disturbance observer.

30-minute rated output 1000Setting

(0.01kgm)= Base speed 1.026 100

0000 to FFFF HEX setting

-

3495 SP295 GDM Motor inertia for disturbance observer

Set the motor inertia for disturbance observer.

Setting (0.001kgm2)=GDM 2 1000

0000 to FFFF HEX setting

-

8. Spindle Parameters 8.4 MDS-C1-SPM

II - 301

No. Items Details Setting range

Standard setting

3521 (PR)

to 3584 (PR)

SP321

to SP384

RPML BSDL

Motor constant (L coil)

This parameter is valid only in the following conditional case: (a) In case that SP034 (SFNC2) bit0=1

and SP034 (SFNC2) bit2=1 Set the motor constant of the L coil of the coil changeover motor.

(Note) It is not allowed for the user to

change the setting.

0000 to FFFF HEX setting

0000

No. Items Details Setting range

Standard setting

3558 SP358 KtL Torque constant 2 for disturbance observer

Set the torque constant for disturbance observer.

30-minute rated output 1000Setting

(0.01kgm)= Base speed 1.026 100

0000 to FFFF HEX setting

-

3559 SP359 GDML Motor inertia 2 for disturbance observer

Set the motor inertia for disturbance observer.

Setting (0.001kgm2)=GDM 2 1000

0000 to FFFF HEX setting

-

8. Spindle Parameters 8.5 Supplement

II - 302

8.5 Supplement

8.5.1 D/A Output Specifications

(1) D/A output specifications

Item Explanation No. of channels 2ch Output cycle 444s (min. value) Output precision 8bit Output voltage range

0V to +5V (zero) to +10V, 0V to +10V during meter output

Output scale setting 1/256 to 128 tiems

Output pins

CN9 connector MO1 = 9 pin MO2 = 19 pin GND = 11pin

Function Phase current feedback output function

U-phase current FB : 7 pin

MDSBSPJ2 MDSC1SP

MO19

Signal

LG

UIFB

2

5

1 Pin

6

4 3

10

7 8

D/A output connector

MO2 19

Signal

VIFB

12

15

11 Pin

16

14 13

20

17 18

8. Spindle Parameters 8.5 Supplement

II - 303

(2) Setting the output data

Input the No. of the data to be output to each D/A output channel.

# No. Abbrev Parameter name 3453 SP253 DA1NO D/A output channel 1 data No. 3454 SP254 DA2NO D/A output channel 2 data No.

No. Output data Original data unit

Standard setting value for output scale

(Setting values in SP255, SP256)

Standard output unit

ch1: Speed meter output

10V=max. speed (0=0V)

0 Depends on the max. speed 0

ch2: Load meter output

10V=120% load (0=0V) 0 Rated 12%/V

1 -

2 Current command Rated 100% = 4096 8 Rated 20%/V

3 Current feedback Rated 100% = 4096 8 Rated 20%/V

4 Speed feedback r/min 13 500(r/min)/V 5 - 6 Position droop 1 = (64000/65536) 671 10/V 7 -

8 Feedrate (FT) 1 = (64000/65536) 629

(When communicating by 3.5ms)

500(r/min)/V

9 - 10 Position command 1 = (64000/65536) 19 (18.64) 360/V 11 - 12 Position feedback 1 = (64000/65536) 19 (18.64) 360/V 13 -

80 Control input 1 81 Control input 2 82 Control input 3 83 Control input 4

HEX Bit correspondence

84 Control output 1 85 Control output 2 86 Control output 3 87 Control output 4

HEX Bit correspondence

8. Spindle Parameters 8.5 Supplement

II - 304

(3) Setting the output scale

# No. Abbrev Parameter name 3455 SP255 DA1MPY D/A output channel 1 magnification 3456 SP256 DA2MPY D/A output channel 2 magnification

Usually, the standard setting value is set for the output scale (SV063, SV 064). When "0" is set, the output will be made as well as when "256" is set.

SP255 10 [V] DATA x 256 x 256 (8bit) + 5 [V] (offset) = Output voltage [V]

(Example) When outputting the position droop with 10/V.

640000 671 10 65536 x 256 x 256 + 5 = 5.999 [V]

9. Machine Error Compensation 9.1 Function Outline

II - 305

9. Machine Error Compensation

9.1 Function Outline

Machine error compensation includes two independent functions: memorized pitch error compensation and memorized relative position compensation. (1) Memorized pitch error compensation

According to the specified parameters this method compensates an axis feed error caused by a ball screw pitch error etc. With the reference point defined as the base set the compensation amount in the division points obtained by equally dividing the machine coordinates. (See Fig. 1. 1) The compensation amount can be set by either the absolute or incremental system. Select the desired method with the #4000:Pinc. Machine position is compensated between division points n and n+1 as much as compensation amount between them by linear approximation.

Fig. 1. 1 Relationship between the compensation amount and machine position

9. Machine Error Compensation 9.1 Function Outline

II - 306

(2) Memorized relative position compensation

This method according to the parameters specified in advance compensates the relative position error between two orthogonal axes caused by deflection of the moving stand. For this as shown in Fig. 1. 2 specify the compensation amount in the compensation axis direction in the division points obtained by equally dividing the machine coordinates of the base axis. The base axis is one of the two orthogonal axes to which relative position compensation applies. This axis is used as the criterion for relative-error measurement. The compensation axis is the coordinate axis that is orthogonal to the base axis. The compensation is actually made for this coordinate axis. The section between division points n and n+1 is compensated smoothly by linear approximation.

Command machine position along base axis

Actual machine position of compensation axis

Reference point

Actual machine position for which no compensation is made

n n+1 n+2

Command machine position

Compensation amount

Compensation amount between division points

: Division points

Fig. 1. 2 Relationship between base and compensation axes

9. Machine Error Compensation 9.1 Function Outline

II - 307

(SETUP PARAM 5. 1/15)

# Item Details Setting range 4000 (PR)

Pinc Machine error offset increment method

Specify whether to use the incremental amount method or absolute amount method when setting the machine error compensation data.

0: Absolute volume method

1: Incremental volume method

<1st axis>

# Item Details Setting range 4001 cmpax Basic axis Specify the basic axis address for machine

error compensation. 1) For pitch error compensation set the

name of the axis to be compensated. 2) For relative position compensation set

the name of the axis to be the base axis. Set as the "system No. + axis name" when using the multi-system. (Example) Z axis for 2nd system: 2Z

X, Y, Z, U, V, W, A, B, or C axis address

4002 drcax Compensation axis

Set the compensation axis address for machine error compensation. 1) For pitch error compensation set the

same axis name as #4001 cmpax. 2) For relative position compensation set

the name of the axis to be actually compensated.

Set as the "system No. + axis name" when using the multi-system. (Example) Z axis for 2nd system: 2Z

X, Y, Z, U, V, W, A, B, or C axis address

4003 rdvno Division point number at reference point position

Set the compensation data No. corresponding to the reference point position. The reference point is actually the base so there is no compensation No. Set the number that is decremented by 1.

4101 to 5124

4004 mdvno Division point number at the most negative side

Set the compensation data No. that is on the farthest negative side.

4101 to 5124

4005 pdvno Division point number at the most positive side

Set the compensation data No. that is on the farthest positive side.

4101 to 5124

4006 sc Compensation scale factor

Set the compensation amount's scale. 0 to 99

4007 spcdv Division interval Set the interval to divide the basic axis. Each compensation data will be the compensation amount for each of these intervals.

1 to 9999999

9. Machine Error Compensation 9.1 Function Outline

II - 308

<2nd axis>

<3rd axis>

<4th axis>

<5th axis>

<6th axis>

<7th axis>

<8th axis>

<9th axis>

<10th axis>

4011 4012 4013 4014 4015 4016 4017

4021 4022 4023 4024 4025 4026 4027

4031 4032 4033 4034 4035 4036 4037

4041 4042 4043 4044 4045 4046 4047

4051 4052 4053 4054 4055 4056 4057

4061 4062 4063 4064 4065 4066 4067

4071 4072 4073 4074 4075 4076 4077

4081 4082 4083 4084 4085 4086 4087

4091 4092 4093 4094 4095 4096 4097

Set the parameters corresponding to the 1st axis parameters 4001 to 4007 for each axis. A maximum of 6 axes can be controlled but as the relative position is compensated settings for 10 axes can be made.

(SETUP PARAM 5. 3/15) to (SETUP PARAM 5. 15/15)

# Item Details Setting range 4101

5124

Set the compensation amount for each axis.

-128 to 127 The actual compensation amount will be the value obtained by multiplying the setting value with the compensation scale.

9. Mmachine Error Compensation 9.2 Setting Compensation Data

II - 309

9.2 Setting Compensation Data

Compensation data can be set according to either absolute or incremental system. "#4000:Pinc" 0: Absolute system

1: Incremental system

(1) Absolute system Feed from the reference point to each division point is executed as shown in Fig. 2. 1. The following is obtained at this time. Set it as the compensation amount.

(Specified position - Real machine position) 2 (Unit of output) For example assume that the feed from the reference point to the +100mm position is executed. Also assume that the real machine position is 99.990mm. In this case the following value is defined as the compensation amount used at the +100mm position: (100000 - 99990) 2 = 20 pulses The resultant value is defined as the compensation amount. Assume that the real machine position resulting when feed to the -100mm position is executed is -99.990mm. In this case the following value is defined as the compensation amount used at the -100mm position: (-100000 - (-99990)) 2 = -20 pulses

+99.990

+100

Compensation amount: 20 pulses (-10m) -99.990

-100

Compensation amount: -20 pulses (10m)

Fig. 2. 1

(2) Incremental system

Fig. 2. 2 contains a machine position that is placed in the positive direction with respect to the reference point. Assume that feed from division n-1 to n (division interval) is executed. In this case the following value is defined as the compensation amount:

(Division interval - Actual movement distance) 2 (Unit of output)

9. Mmachine Error Compensation 9.2 Setting Compensation Data

II - 310

(3) Fig. 2. 3 contains a machine position that is placed in the negative direction with respect to the reference

point. Assume that feed from division point n+1 to n by the division interval is executed. In this case the following value is defined as the compensation amount: (Division interval + Actual movement distance) 2 (Unit of output)

n n-1 1

n+1n 1

n: Division point compensation number 1: Division interval

Fig. 2. 2 Fig. 2. 3

Unit : Unit of output Range : -128 to 127

(Note) The unit of output is used as the unit of setting. The actual unit of compensation pulses depends on the compensation scale factor.

9. Machine Error Compensation 9.3 Example in Using a Linear Axis as the Base Axis

II - 311

9.3 Example in Using a Linear Axis as the Base Axis

(1) When "mdvno" or "pdvno" exists at both ends of "rdvno":

#4101

Compensation amount in incremental system

#4103#4102 #4104 #4105 #4106

2

1

-1

Error

-2

-3

(1) (3) (-3) (-2) (0) (3)

(3) (-2) (0) (-2)

(-1) (1)

Base axis machine coordinate

3

Compensation amount in absolute system

Division point number #4101 #4102 #4103 #4104 #4105 #4106 rdvno 4103 Specified machine position -300.000 -200.000 -100.000 100.000 200.000 300.000 mdvno 4101 Real machine position -299.999 -200.000 -100.003 100.002 200.002 299.999 pdvno 4106

Increment al

2 6 -6 -4 0 6 Compensation amount

Absolute -2 0 6 -4 -4 2 If the setting range (mdvno to "pdvno") is exceeded the compensation will be based on compensation amount at mdvno or "pdvno".

9. Machine Error Compensation 9.3 Example in Using a Linear Axis as the Base Axis

II - 312

(2) When the range compensated is only the positive range:

Compensation amount in incremental system

#4114#4113 #4116 #4117

2

1

-1

Error

-2

-3

(-2) (1) (0) (3) (1)

(-2) (-1)

(2)

Base axis machine coordinate

3 #4115

(-1)

(3)

Compensation amount in absolute system

Division point number #4113 #4114 #4115 #4116 #4117 rdvno 4112 Incremen tal

-4 2 0 6 2 mdvno 4113Compensati on amount Absolute -4 -2 -2 4 6 pdvno 4117

If the machine position exceeds "pdvno" the compensation will be based on the compensation amount at "pdvno". If the machine position is negative in this case no compensation will be executed.

9. Machine Error Compensation 9.3 Example in Using a Linear Axis as the Base Axis

II - 313

(3) When the range compensated is only the negative range:

#4128#4127 #4130#4126

2

1

-1

-2

-3

(3) (1) (0) (-3)

(3) (3)

(-1)

3 #4129

(2)

(-2)

(-1) (1)

#4125

(-1)

Compensation amount in incremental system

Error

Base axis machine coordinate

Compensation amount in absolute system

Division point number #4125 #4126 #4127 #4128 #4129 #4130 rdvno 4130 Incremen tal

-2 2 6 2 0 -6 mdvno 4125Compensati on amount

Absolute -2 -4 -2 4 6 6 pdvno 4130 If the machine position exceeds "mdvno" the compensation will be based on compensation amount at "mdvno".

9. Machine Error Compensation 9.3 Example in Using a Linear Axis as the Base Axis

II - 314

(4) When compensation is executed in a range that contains no reference point:

#4136 #4135 #4138 #4139

2

1

-1

-2

-3

(1)(-1) (-1) (3)

(-1) (-2)

(2)

3 #4137

(1)

#4140

Compensation amount in incremental system

Error

Base axis machine coordinate

Compensation amount in absolute system

Division point number #4135 #4136 #4137 #4138 #4139 #4140 rdvno 4134 Incremen tal

-2 -2 6 2 mdvno 4136Compensati on amount

Absolute -2 -4 2 4 pdvno 4140 In this case the compensation is executed in the range from "mdvno" to "pdvno". This setting rule applies also when the compensation is executed in a range which contains negative machine positions and no reference point.

9. Machine Error Compensation 9.4 Example in Using a Rotation Axis as the Base Axis

II - 315

9.4 Example in Using a Rotation Axis as the Base Axis

#4124#4123 #4126 #4127

2

1

-1

-2

-3

(-2) (1) (0) (3) (1)

(-2) (-1)

(2)

3 #4125

(-1)

(3)

(-3)

#4128

(0)

360

Compensation amount in incremental system

Error

Base axis machine coordinate

Compensation amount in absolute system

Division point number #4123 #4124 #4125 #4126 #4127 #4128 rdvno 4122 Incremen tal

-4 2 0 6 2 -6 mdvno 4123Compensati on amount Absolute -4 -2 -2 4 6 0 pdvno 4128

In this case the sum of the compensation amounts set according to the incremental system is always "0". For the absolute system the compensation amount at the terminal point (360 degrees) is always "0".

10. PLC Constants 10.1 PLC Timer

II - 316

10. PLC Constants

10.1 PLC Timer

(SETUP PARAM 6. 1/14) to (SETUP PARAM 6. 2/14) # PLC device Item Details Setting range

6000

6015

T000

T015

10ms adding timer <10ms>

Set the time for the timer used in the PLC program (ladder). (Note) This setting value is valid when

parameter "#6449 bit0" in the following "[BIT SELECT]" is set to "0".

0 to 32767 (10ms)

6016

6095

T016

T095

100ms adding timer <10ms>

Set the time for the timer used in the PLC program (ladder). (Note) This setting value is valid when

parameter "#6449 bit0" in the following "[BIT SELECT]" is set to "0".

0 to 32767 (100ms)

6096

6103

T096

T103

100ms cumulative timer <100ms INC>

Set the time for the timer used in the PLC program (ladder). (Note) This setting value is valid when

parameter "#6449 bit0" in the following "[BIT SELECT]" is set to "0".

0 to 32767 (100ms)

(SETUP PARAM 6. 10/14) to (SETUP PARAM 6. 14/14)

# PLC device Item Details Setting range 6600

6999

R1200/bit0 R1250/bit0

R1224/bitF R1274/bitF

PLC timer expansion 10ms adding timer <10ms>

Set the time for the expanded PLC timer This is set for the timer coils: R1200 to R1224, and timer contacts: R1250 to R1274. A timer command can be issued to a contact other than the existing timer contacts (T0 to T103, Q0 to Q151).

0 to 32767 (10ms)

10.2 PLC Counter

(SETUP PARAM 6. 3/14) # PLC device Item Details Setting range

6200

6223

C000

C023

Counter Set the time for the counter used in the PLC program (ladder). (Note) This setting value is valid when

parameter "#6449 bit1" in the following "[BIT SELECT]" is set to "0".

0 to 32767

10. PLC Constants 10.3 PLC Constants

II - 317

10.3 PLC Constants

(SETUP PARAM 6. 4/14) # PLC device Item Details Setting range

6301

6348

R2800,2801

R2894,2895

PLC constant Set the value to be set in the data type R register used in the PLC program (ladder). Even if the data is set in the R register that corresponds to the PLC side when this parameter is displayed the screen will not change. Enter a different screen once and then select this screen again.

-99999999 to 99999999

(SETUP PARAM 6. 5/14)

# PLC device Item Details Setting range 6349

6396

R4900,4901

R4994,4995

PLC constant Set the value to be set in the data type R register used in the PLC program (ladder). Even if the data is set in the R register that corresponds to the PLC side when this parameter is displayed the screen will not change. Enter a different screen once and then select this screen again.

-99999999 to 99999999

10.4 Selecting the PLC Bit (SETUP PARAM 6. 6/14) to (SETUP PARAM 6. 7/14)

# PLC device Item Details Setting range 6401 6402

6495 6496

R2900-Low R2900-High R2947-Low R2947-High

Bit selection This is the bit type parameter used in the PLC program (ladder). Even if the data is set in the R register that corresponds to the PLC side when this parameter is displayed the screen will not change. Enter a different screen once and then select this screen again. Some of the parameters following #6449 may be fixed according to the usage purpose. Refer to the PLC Program Development On-board Instruction Manual.

0: OFF 1: ON

(SETUP PARAM 6. 7/14) to (SETUP PARAM 6. 9/14)

# PLC device Item Details Setting range 6497 6498

6595 6596

R4400-Low R4400-High R4449-Low R4449-High

Bit selection expansion

This is the bit type parameter (expansion) used in the PLC program (ladder). Even if the data is set in the R register that corresponds to the PLC side when this parameter is displayed the screen will not change. Enter a different screen once and then select this screen again.

0: OFF 1: ON

10. PLC Constants 10.4 Selecting the PLC Bit

II - 318

Table: "Contents of bit selection parameters #6449 to #6496"

Symbol name

7 6 5 4 3 2 1 0

0 #6449

R2924 L

NC card Controller thermal alarm on

Setting display unit thermal alarm on

- Counter C retention

Integrating timer T retention

PLC counter program on

PLC timer program on

1 0

1

#6450 R2924 H

External alarm message display

Alarm/ operator change

Full screen display of message

- Operator message on

R system

F system

Alarm message on

2

#6451 R2925 L - -

GX-Developer communi- cation on

PLC development environment selection

Onboard editing not possible

APLC custom release Onboard on

3

#6452 R2925 H -

GOT communi- cation connection

Counter (fixed) retention

Integrating timer (fixed) retention

-

4

#6453 R2926 L - - - - -

Message language change code

5

#6454 R2926 H

6

#6455 R2927 L - - - - - - - -

7

#6456 R2927 H - - - - - - - -

8

#6457 R2928 L

9

#6458 R2928 H

A

#6459 R2929 L

B

#6460 R2929 H

C

#6461 R2930 L

D

#6462 R2930 H

E #6463

R2931 L

F #6464

R2931 H

High-speed input specification 1

High-speed input specification 2

High-speed input specification 4 (Spare)

High-speed input specification 3 (Spare)

High-speed output specification 1

High-speed output specification 2

High-speed output specification 3 (Spare)

High-speed output specification 4 (Spare)

10. PLC Constants 10.4 Selecting the PLC Bit

II - 319

Symbol

name 7 6 5 4 3 2 1 0

0 #6465

R2932 L - - - - - - - -

1 #6466

R2932 H - - - - - - - -

2 #6467

R2933 L - - - - - - - -

3 #6468

R2933 H

4 #6469

R2934 L - MC alarm 4 output off

5 #6470

R2934 H

6 #6471

R2935 L - - - - - - - -

7 #6472

R2935 H - - - - - - - -

8 #6473

R2936 L - -

9 #6474

R2936 H

A #6475

R2937 L

B #6476

R2937 H

C #6477

R2938 L

D #6478

R2938 H

E #6479

R2939 L

F #6480

R2939 H

Standard PLC parameter

(Note 1) Be sure to set the bits indicated - and blanks to 0. (Note 2) Parameters #6481 to #6496 are reserved for debugging by Mitsubishi.

11. Macro List

II - 320

11. Macro List

(SETUP PARAM 7. 1/3) # Item Details Setting range (unit)

7001 to

7091

M [01] to M [10]

Set the M code used for calling out the macro with the M command. This is valid when #1195 Mmac is set to 1.

1 to 9999

7002 to

7092

Set the macro call out type.

0 to 3

7003 to

7093

Set the No. of the program to be called out.

1 to 99999999

M2mac Set the type and program No. for when calling out the macro with the 2nd miscellaneous command. The macro will be called out with the #1170 M2name address command when #1198 M2mac is set to 1.

7102 Same as the M call macro.

0 to 3

7103 Same as the M call macro.

0 to 99999999

(SETUP PARAM 7. 2/3)

# Item Details Setting range (unit) 7201

to 7291

G [01] to G [10]

Set the G code to be used when calling the macro with a G command. Do not set a G code used in the system.

1 to 255

7202 to

7292

Same as the M call Marco.

0 to 3

7203 to

7293

Same as the M call Marco.

1 to 99999999

Smac Set the type and program No. for when calling the macro with an S command. This is valid when #1196 Smac is set to 1.

7302 Same as the M call Marco.

0 to 3

7303 Same as the M call Marco.

1 to 99999999

Tmac Set the type and program No. for when calling the macro with a T command. This is valid when #1197 Tmac is set to 1.

7312 Same as the M call macro.

0 to 3

7313 Same as the M call macro.

0 to 99999999

0 M98 P; and equivalent value call 1 G65 P; and equivalent value call 2 G66 P; and equivalent value call 3 G66.1 P; and equivalent value call

others M98 P; and equivalent value call

11. Macro List

II - 321

(SETUP PARAM 7. 3/3)

# Item Details Setting range 7401 Valid The ASCII code macro parameters (#7402 to

7405) are validated. 0: Invalid 1: Valid

0/1

7402 Code Set the ASCII code used to call macros with the ASCII code.

L system: A, B, D, F, H, I, J, K, M, Q, R, S, T

M system: A, B, F, H, I, K, M, Q, R, S, T

7403 Type Set the macro call type. 0: M98, 1: G65, 2: G66, 3: G66.1

0 to 3

7404 Program No.

Set the number of the program called with macro call.

0 to 99999999

7405

ASCII [01]

Variable When the call type is "0", set the variable number set after the ASCII code.

100 to 149

7411 Valid The ASCII code macro parameters (#7412 to 7415) are validated. 0: Invalid 1: Valid

0/1

7412 Code Set the ASCII code used to call macros with the ASCII code.

L system: A, B, D, F, H, I, J, K, M, Q, R, S, T

M system: A, B, F, H, I, K, M, Q, R, S, T

7413 Type Set the macro call type. 0: M98, 1: G65, 2: G66, 3: G66.1

0 to 3

7414 Program No.

Set the number of the program called with macro call.

0 to 99999999

7415

ASCII [02]

Variable When the call type is "0", set the variable number set after the ASCII code.

100 to 149

12. Position Switch 12.1 Outline of Function

II - 322

12. Position Switch

12.1 Outline of Function

The position switch (PSW) is used as an alternate switch for the dog switch provided on an axis of the machine. The position switch uses parameters by which the names of axes and their corresponding coordinates indicating imaginary dog positions are defined in advance. When the machine reaches the imaginary dog position a signal is output to the PLC interface. The position switch thus works as an imaginary dog switch.

(SETUP PARAM 8. 1/1) # Item Details Setting range (unit)

7500 Pcheck High-speed switching of position switch

Specify whether to perform position switch area checking at high speeds. 0: Do not perform position switch area

checking at high speed (do it the same as before).

1: Perform position switch area checking at high speed.

0/1

75 1 Axis name Specify the name of the axis for which a position switch is provided.

X, Y, Z, U, V, W, A, B, or C axis address

75 2 Imaginary dog position 1

When the machine enters the range between imaginary dog positions 1 and 2, a signal is output to the PLC.

-99999.999 to 99999.999

(0.001mm) 75 3 Imaginary dog

position 2 System 1 device X 270 System 2 device U0F0

75 4 Selection of area check method

When position switch area checking at high speed is selected, specify the mode of area checking, i.e., whether to use the command type machine position or detector feedback position, for each position switch point. 0: Use the command type machine

position as the machine position for position switch area checking.

1: Use the detector feedback position as the machine position for position switch area checking.

Note: This parameter is valid only when 1 set in "#7500 Pcheck".

0/1

12. Position Switch 12.1 Outline of Function

II - 323

Position switch numbers of PSW1 to PSW8 and signal devices

System 1 device System 2 device PSW1 #7501 #7502 #7503 X270 U0F0 PSW2 #7511 #7512 #7513 X271 U0F1 PSW3 #7521 #7522 #7523 X272 U0F2 PSW4 #7531 #7532 #7533 X273 U0F3 PSW5 #7541 #7542 #7543 X274 U0F4 PSW6 #7551 #7552 #7553 X275 U0F5 PSW7 #7561 #7562 #7563 X276 U0F6 PSW8 #7571 #7572 #7573 X277 U0F7

Instead of the dog switch provided on the machine axis the coordinate values indicating imaginary dog positions (dog1 and dog2) on the coordinate axis of the axis name preset with axis are set with the position switches (PSW1 - PSW8). When the machine reaches the position the signal is output to the device corresponding to the PLC interface. Example of settings of dog1 and dog2 and operation

Setting of dog1 and dog2

dog1, dog2 position Operation

dog1 < dog2 dog1 dog2

A signal is output between dog1 and dog2.

dog1 > dog2 dog2 dog1

A signal is output between dog1 and dog2.

dog1 = dog2 dog1 = dog2

If dog1 equals dog2 the dog1 position triggers a signal.

dog1

dog2

PSW width

Imaginary dog

Basic machine coordinate system zero point

12. Position Switch 12.2 Canceling the Position Switch

II - 324

Rotation axis Setting of dog1 and dog2 dog1, dog2 position Description

dog1 < dog2 dog2 dog1

(Example) dog1 = 30.000 dog2 = 330.000

A signal is output between dog1 and dog2.

dog1 dog2

(Example) dog1 = -30.000 dog2 = 30.000

A signal is also output when dog1 is negative.

dog1 > dog2 dog1 dog2

(Example) dog1 = 330.000 dog2 = 30.000

A signal is output between dog2 and dog1.

dog1 - dog2 360 dog2 dog1

(Example) dog1 = 30.000 dog2 = 390.000

A signal is kept output when the difference between dog1 and dog2 exceeds 360 degrees.

12.2 Canceling the Position Switch

To cancel the position switch enter the number (#75 1) of the position switch to be canceled in # ( ) of the setting field enter a slash "/" in DATA ( ) then press the INPUT key. This deletes the axis name for the specified position switch thus invalidating the position switch. The data specified for and are still stored in memory. To validate the position switch again therefore it is enough to specify the axis name only.

13. Auxiliary Axis Parameter

II - 325

13. Auxiliary Axis Parameter

Turn the NC power OFF after setting parameters indicated with a (PR) in the table. The setting will be validated after the power is turned ON again.

No. Name Details Setting range Default value

1 (PR)

MSR Motor series Set the motor series. This is automatically judged by the system when the default value (0000) is set.

0000 to FFFF (hexadecimal)

0000

2 (PR)

RTY Regeneration option type

Set the regenerative resistor type. Do not set values without a description.

0 0 0 0 (Default value)

Setting value Details

0 Amplifier standard built-in resistor (10CT has no built-in resistor)

1 Setting prohibited 2 MR-RB032 (30W) 3 MR-RB12 (100W) 4 MR-RB32 (300W) 5 MR-RB30 (300W) 6 MR-RB50 (500W) 7~F

3 (PR)

PC1 Motor side gear ratio (machine rotation ratio)

1 to 32767 1

4 (PR)

PC2 Machine side gear ratio (motor rotation ratio)

Set the No. of gear teeth on the motor side and the No. of gear teeth on the machine side as an integer reduced to its lowest terms. Set the total gear ratio if there are multiple gear levels. For rotation axes, set the No. of motor rotation speed per machine rotation.

1 to 32767 1

5 (PR)

PIT Feed pitch Set 360 (default value) for rotation axes. Set the feed lead for linear axes.

1 to 32767 ( or mm)

360

6 INP In-position detection width

In-position is detected when the position droop becomes this setting value or less.

1 to 32767 (1/1000 or m)

50

13. Auxiliary Axis Parameter

II - 326

No. Name Details Setting range Default value

7 ATU Auto-tuning Set the adjustment of the auto-tuning. Do not set values without a description.

0 1 0 2 (Default setting value)

Setting value Details

1 Low response (low-rigidity loads, loads which easily vibrate)

2 Standard setting value 3 Standard setting value 4 Standard setting value

5 High response (high-rigidity loads, loads which do not easily vibrate)

Setting value Details

0 Standard

2 Large friction amount (set the position loop gain slightly lower)

Setting value Details

0 Only auto-tuning PG2, VG2, VIC, and GD2.

1 Only auto-tuning PG1, PG2, VG1, VG2, VIC, and GD2 (total gain). (Standard setting)

2 No auto-tuning. 8 PG1 Position loop

gain 1 Set the position loop gain for the model loop. Determine the tracking ability regarding the position commands.

4 to 1000 (1/s) 70

9

(Not used.) 0

10 EMGt Deceleration control time constant

Set the deceleration time from the clamp speed (Aspeed1). For normal rapid traverse, set the same value as the acceleration/deceleration time constant.

0 to 32768 (ms) 500

11

(Not used.) 0

12

(Not used.) 0

13 MBR Vertical axis drop prevention time

Input the time the servo OFF is delayed during servo OFF command. Increase the setting by 100ms at a time and set the minimum value where the axis does not drop.

0 to 1000 (ms) 100

14 NCH Notch filter No.

Set the frequency of the machine resonance suppression filter. Do not set values without a description.

Setting value 0 1 2 3 4 5 6 7

Frequency (Hz)

No start 1125 563 375 282 225 188 161

13. Auxiliary Axis Parameter

II - 327

No. Name Details Setting range Default value

15

(Not used.) 0

16 JIT Jitter compensation

Set the No. of ignored jitter compensation pulses. Do not set values without a description.

Setting value 0 1 2 3 Number of ignore

pulses No start 1 2 3

17

(Not used.) 0

18

(Not used.) 0

19 PG2 Position loop gain 2

Set the position loop gain of the actual loop. Determine the position responsiveness for external disturbance.

1 to 500 (1/s) 25

20 VG1 Speed loop gain 1

Set the speed loop gain of the model loop. Determine the tracking ability regarding the speed commands.

20 to 5000 (1/s) 1200

21 VG2 Speed loop gain 2

Set the speed loop gain of the actual loop. Determine the speed responsiveness for external disturbance.

20 to 8000 (1/s) 600

22 VIC Speed integral compensation

Determine the characteristics of the speed low-frequency region.

1 to 1000 (ms) 20

23 VDC Speed differential compensation

PI control normally results from a default value of 1000. Adjust the overshoot amount by lowering in increments of 20.

0 to 1000 1000

24

DG2 Load inertia ratio

Set the load inertia ratio for the motor inertia. 0.0 to 50.0 (fold)

2.0

25

(Not used.) 0

30 (PR)

MTY Motor type Set the motor type. This is automatically judged by the system when the default value (0000) is set.

0000 to FFFF (hexadecimal)

0000

13. Auxiliary Axis Parameter

II - 328

No. Name Details Setting range Default value

50 MD1 D/A output channel 1 data No.

Set the Nos. of the data to be output on D/A output channel 1. 0 0 0 0 (Default setting value)

Setting value Details Magnification

0 Speed feedback (with sign)

Maximum rotation speed = 8V

1 Current feedback (with sign)

Maximum current (torque) = 8V

2 Speed feedback (without sign)

Maximum rotation speed = 8V

3 Current feedback (without sign)

Maximum current (torque) = 8V

4 Current command

Maximum current (torque) = 8V

5 Command FT

100000 [degrees/min] = 10V

6 Position droop 1 (1/1)

2048 [pulse] = 10V

7 Position droop 2 (1/4)

8192 [pulse] = 10V

8 Position droop 3 (1/16)

32768 [pulse] = 10V

9 Position droop 4 (1/32)

65536 [pulse] = 10V

A Position droop 5 (1/64)

131072 [pulse] = 10V

51 MO1 D/A output channel 1 output offset

Set this value when the zero level of D/A output channel 1 is not suitable.

999 to 999 (mV)

0

52

(Not used.) 0

53 MD2 D/A output channel 2 data No.

Set the Nos. of the data to be output on D/A output channel 2. The descriptions are the same as "50 MD1".

0000 to FFFF (hexadecimal)

0000

54 MO2 D/A output channel 2 output offset

Set this value when the zero level of D/A output channel 2 is not suitable.

-999 to 999 (mV)

0

55

(Not used.) 0

100 (PR)

station No. of indexing stations

Set the No. of stations. For linear axes, this value is expressed by: No. of divisions = No. of stations -1.

2 to 360 2

13. Auxiliary Axis Parameter

II - 329

No. Name Details Setting range Default value

101 (PR)

Cont1 Control parameter 1

This is a HEX setting parameter. Set bits without a description to their default values.

bit F E D C B A 9 8 7 6 5 4 3 2 1 0 Default value 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0

bit Meaning when "0" is set Meaning when "1" is set 0

1 High-speed zero point return after establishment of zero point.

Dog-type return for each zero point return operation.

2 3 4 5 6 7

8 Reference point return direction (+)

Reference point return direction (-)

9 Rotation direction determined by operation control signal (DIR)

Rotation direction in the shortcut direction

A Machine basic position becomes the origin point

Electrical zero point becomes the origin point

B C

D Coordinate zero point creation valid

Zero point established at power supply ON position

E Rotation direction in operation control signal (DIR) or in the shortcut direction

Rotation direction in the random position command sign direction

F Stopper direction is positioning direction

Stopper direction is in the sign direction of the stopper amount

13. Auxiliary Axis Parameter

II - 330

No. Name Details Setting range Default value

102 (PR)

Cont2 Control parameter 2

This is a HEX setting parameter. Set bits without a description to their default values.

bit F E D C B A 9 8 7 6 5 4 3 2 1 0 Default value 0 0 0 0 0 0 0 0 1 0 0 0 0 1 1 0

bit Meaning when "0" is set Meaning when "1" is set 0 1 Error not corrected at servo OFF Error corrected at servo OFF 2 Linear axis Rotation axis 3 Station assignment direction CW Station assignment direction CCW 4 Uniform index Non-uniform index 5 DO channel standard assignment DO channel reverse assignment 6 2-wire detector communication 4-wire detector communication 7 Incremental detection Absolute position detection 8 9 A B C D E F

103 (PR)

EmgCont Emergency stop control

This is a HEX setting parameter. Set bits without a description to their default values.

bit F E D C B A 9 8 7 6 5 4 3 2 1 0 Default value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

bit Meaning when "0" is set Meaning when "1" is set

0 External emergency stop valid External emergency stop invalid (default value)

1 Dynamic brake stop at emergency stop

Deceleration control stop at emergency stop

2 NC bus emergency stop input valid

NC bus emergency stop input invalid

3 NC bus emergency stop output valid

NC bus emergency stop output invalid

4 5 6 7 8 9 A B C D E F

13. Auxiliary Axis Parameter

II - 331

No. Name Details Setting range Default value

104 (PR)

tleng Linear axis stroke length

Set the movement stroke length for linear axes. This is meaningless when setting non-uniform assignments or commanding random positions.

0.001 to 99999.999 (mm)

100.000

110 ZRNspeed Reference point return speed

Set the clamp value of the feedrate when a reference point return is carried out. The feedrate becomes the manual operation speed of the parameter group selected at that time, but it is clamped by this parameter setting value.

1 to 100000 (/min or mm/min)

1000

111 ZRNcreep Reference point return creep speed

Set the approach speed to the reference point after dog detection during a reference point return.

1 to 65535 (/min or mm/min)

200

112 grid mask Grid mask Set the amount that the dog is artificially extended. Set 1/2 the grid spacing as a standard.

0 to 65536 (1/1000 or m)

0

113 (PR)

grspc Grid spacing

Divide the grid spacing that is the conventional motor rotation movement amount into 2, 4, 8, or 16 divisions.

0 to 4 (1/2n division)

0

114 ZRNshift Reference point shift amount

Set the shift amount in a dog-type reference point return from the electric zero point determined on the grid to the reference point.

0 to 65536 (1/1000 or m)

0

115 ST. ofset Station offset

Set the distance (offset) from the reference point to station 1.

-99999.999 to 99999.999 ( or mm)

0.000

116 (PR)

ABS base Absolute position zero point

When movement of the machine coordinate zero point from the origin point is required during absolute position initializing, set that movement amount.

-99999.999 to 99999.999 ( or mm)

0.000

117 Limit (+) Soft limit (+) Commands in the plus direction that exceed this setting value are not possible. If the machine is in a position exceeding the setting value, commands in the minus direction are possible. The soft limit function will not operate if Limit (+) and Limit (-) are set to the same value.

-99999.999 to 99999.999 (mm)

1.000

118 Limit (-) Soft limit (-) Commands in the minus direction that exceed this value are not possible. If the machine is in a position exceeding the setting value, commands in the plus direction are possible.

-99999.999 to 99999.999 (mm)

1.000

13. Auxiliary Axis Parameter

II - 332

No. Name Details Setting range Default value

120 ABS Type Absolute position detection parameter

This parameter is set as a hexadecimal. Set the default value for bits that have no description.

bit F E D C B A 9 8 7 6 5 4 3 2 1 0 Default value 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0

bit Meaning when "0" is set Meaning when "1" is set 0 1 Dogless-type method initializing Dog-type method initializing

2 Mechanical stopper method initializing

Origin point alignment method initializing

3 Electrical zero point direction (+) Electrical zero point direction (-) 4 5 6 7 8 9 A B C D E F

123 ABS check

Absolute position power OFF tolerable movement value

Set the value for the tolerable amount of movement for a machine that moved during power OFF in an absolute position detection system. The "Absolute position power OFF movement exceeded (ABS)" signal will turn ON if the machine moves more than this setting value during power OFF. The movement amount is not checked when this parameter is set to 0.000.

0.000 to 99999.999 ( or mm)

0.000

130 backlash Backlash compensa- tion amount

Set the backlash compensation amount. 0 to 9999 (1/1000 or m)

0

132

(Not used.) 0

133

(Not used.) 0

134

(Not used.) 0

135

(Not used.) 0

13. Auxiliary Axis Parameter

II - 333

< Operation parameter group 1 >

No. Name Details Setting range Default value

150 Aspeed1 Operation parameter group 1 Automatic operation speed

Set the feedrate during automatic operation when operation parameter group 1 is selected. This parameter is regarded as the clamp value for the automatic operation speeds and manual operation speeds of all operation groups. A speed exceeding Aspeed1 cannot be commanded, even if set in the parameters.

1 to 100000 (/min or mm/min)

5000

151 Mspeed1 Operation parameter group 1 Manual operation speed

Set the feedrate during manual operation or JOG operation when operation parameter group 1 is selected.

1 to 100000 (/min or mm/min)

2000

152 time1.1 Operation parameter group 1 Acceleration/ deceleration time constant 1

Set the linear acceleration/deceleration time for Aspeed 1(the operation parameter group 1 automatic operation speed (clamp speed)) when operation parameter group 1 is selected. When operating at speeds less than the clamp speed, the axis will linearly accelerate/decelerate at the inclination determined above. When this is set together with acceleration/deceleration time constant 2, S-shape acceleration/deceleration is carried out. In this case, set the acceleration/deceleration time of the linear part in this parameter.

1 to 9999 (ms) 100

153 time1.2 Operation parameter group 1 Acceleration/ deceleration time constant 2

Set this parameter when carrying out S-shape acceleration/ deceleration. When S-shape acceleration/deceleration is carried out, set the total time of the non-linear parts. When "1" is set in this parameter, linear acceleration/deceleration is carried out. In the handle feed operation mode, this set value is regarded as the time constant for the linear acceleration/deceleration.

1 to 999 (ms) 1

13. Auxiliary Axis Parameter

II - 334

No. Name Details Setting range Default value

154 TL1 Operation parameter group 1 Torque limit value

Set the motor output torque limit value when operation parameter group 1 is selected. At the default value, the torque is limited at the maximum torque of the motor specification. Set the default value when torque limit is not especially required. In the stopper positioning operation mode, this becomes the torque limit value when positioning to the stopper starting coordinates.

1 to 500 (%) 500

155 OD1 Operation parameter group 1 Excessive error detection width

Set the excessive error detection width when operation parameter group 1 is selected. An alarm of excessive error (S03 0052) is detected when the position droop becomes larger than this setting value. In the stopper positioning operation mode, this becomes the excessive error detection width when positioning to the stopper starting coordinates.

0 to 32767 ( or mm)

100

156 just1 Operation parameter group 1 Set position output width

The signal indicating that the machine position is at any one of the stations is the set position reached (JST) signal. During automatic operation, the automatic set position reached (JSTA) signal is also output under the same conditions. Set the tolerable values at which these signals are output when operation parameter group 1 is selected. These signals turn OFF when the machine position is separated from the station by more than this value.

0.000 to 99999.999 ( or mm)

0.500

157 near1 Operation parameter group 1 Near set position output width

The signal indicating that the machine position is near any one of the station positions is the near set position (NEAR) signal. Set the tolerable value at which this signal is output when operation parameter group 1 is selected. This value is generally set wider than the set position output width. During operations, this is related to special commands when the station selection is "0".

0.000 to 99999.999 ( or mm)

1.000

13. Auxiliary Axis Parameter

II - 335

< Operation parameter group 2 >

No. Name Details Setting range Default value

158 Aspeed2 Operation parameter group 2 Automatic operation speed

Set the feedrate during automatic operation when operation parameter group 2 is selected.

1 to 100000 (/min or mm/min)

5000

159 Mspeed2 Operation parameter group 2 Manual operation speed

Set the feedrate during manual operation or JOG operation when operation parameter group 2 is selected.

1 to 100000 (/min or mm/min)

2000

160 time2.1 Operation parameter group 2 Acceleration/ deceleration time constant 1

Set the linear acceleration/deceleration time for the operation parameter group 1 automatic operation speed (clamp speed) when operation parameter group 2 is selected. When operating at speeds less than the clamp speed, the axis will linearly accelerate/decelerate at the inclination determined above. When this is set together with acceleration/deceleration time constant 2, S-shape acceleration/deceleration is carried out. In this case, set the acceleration/deceleration time of the linear part in this parameter.

1 to 9999 (ms) 100

161 time2.2 Operation parameter group 2 Acceleration/ deceleration time constant 2

Set this parameter when carrying out S-shape acceleration/deceleration. When S-shape acceleration/deceleration is carried out, set the total time of the non-linear parts. When 1 is set in this parameter, linear acceleration/deceleration is carried out. In the handle feed operation mode, this set value is regarded as the time constant for the linear acceleration/deceleration.

1 to 9999 (ms) 1

13. Auxiliary Axis Parameter

II - 336

No. Name Details Setting range Default value

162 TL2 Operation parameter group 2 Torque limit value

Set the motor output torque limit value when operation parameter group 2 is selected. At the default value, the torque is limited at the maximum torque of the motor specifications. Set the default value when torque limit is not especially required. In the stopper positioning operation mode, this becomes the torque limit value during stopper operation.

1 to 500 (%) 500

163 OD2 Operation parameter group 2 Excessive error detection width

Set the excessive error detection width when operation parameter group 2 is selected. An excessive error alarm (S03 0052) is detected when the position droop becomes larger than this setting value. In the stopper positioning operation mode, this becomes the excessive error detection width during stopper operation.

0 to 32767 ( or mm)

100

164 just2 Operation parameter group 2 Set position output width

The signal indicating that the machine position is at any one of the stations is the set position reached (JST) signal. During automatic operation, the automatic set position reached (JSTA) signal is also output under the same conditions. Set the tolerable values at which these signals are output when operation parameter group 2 is selected. These signals turn OFF when the machine position is separated from the station by more than this value.

0.000 to 99999.999 ( or mm)

0.500

165 near2 Operation parameter group 2 Near set position output width

The signal indicating that the machine position is near any one of the station positions is the near set position (NEAR) signal. Set the tolerable values at which these signals are output when operation parameter group 2 is selected. These values are generally set wider than the set position output width. During operations, this is related to special commands when the station selection is 0.

0.000 to 99999.999 ( or mm)

1.000

13. Auxiliary Axis Parameter

II - 337

< Operation parameter group 3 >

No. Name Details Setting range Default value

166 Aspeed3 Operation parameter group 3 Automatic operation speed

Set the feedrate during automatic operation when operation parameter group 3 is selected.

1 to 100000 (/min or mm/min)

5000

167 Mspeed3 Operation parameter group 3 Manual operation speed

Set the feedrate during manual operation or JOG operation when operation parameter group 3 is selected.

1 to 100000 (/min or mm/min)

2000

168 time3.1 Operation parameter group 3 Acceleration /deceleration time constant 1

Set the linear acceleration/deceleration time for the operation parameter group 1 automatic operation speed (clamp speed) when operation parameter group 3 is selected. When operating at speeds less than the clamp speed, the axis will linearly accelerate/decelerate at the inclination determined above. When this is set together with acceleration/deceleration time constant 2, S-shape acceleration/deceleration is carried out. In this case, set the acceleration/deceleration time of the linear part in this parameter.

1 to 9999 (ms) 100

169 time3.2 Operation parameter group 3 Acceleration /deceleration time constant 2

Set this parameter when carrying out S-shape acceleration/deceleration. When S- shape acceleration/deceleration is carried out, set the total time of the non-linear parts. When 1 is set in this parameter, linear acceleration/deceleration is carried out. In the handle feed operation mode, this set value is regarded as the time constant for the linear acceleration/deceleration.

1 to 9999 (ms) 1

13. Auxiliary Axis Parameter

II - 338

No. Name Details Setting range Default value

170 TL3 Operation parameter group 3 Torque limit value

Set the motor output torque limit value when operation parameter group 3 is selected. At the default value, the torque is limited at the maximum torque of the motor specifications. Set the default value when torque limit is not especially required. In the stopper positioning operation mode, this becomes the pressing torque limit value after completion of the positioning.

1 to 500 (%) 500

171 OD3 Operation parameter group 3 Excessive error detection width

Set the excessive error detection width when operation parameter group 3 is selected. An excessive error alarm (S03 0052) is detected when the position droop becomes larger than this setting value. In the stopper positioning operation mode, this becomes the excessive error detection width during pressing after completion of the positioning.

0 to 32767 ( or mm)

100

172 just3 Operation parameter group 3 Set position output width

The signal indicating that the machine position is at any one of the stations is the set position reached (JST) signal. During automatic operation, the automatic set position reached (JSTA) signal is also output under the same conditions. Set the tolerable values at which these signals are output when operation parameter group 3 is selected. These signals turn OFF when the machine position is separated from the station by more than this value.

0.000 to 99999.999 ( or mm)

0.500

173 near3 Operation parameter group 3 Near set position output width

The signal indicating that the machine position is near any one of the station positions is the near set position (NEAR) signal. Set the tolerable values at which these signals are output when operation parameter group 3 is selected. These values are generally set wider than the set position output width. During operations, this is related to special commands when the station selection is 0.

0.000 to 99999.999 ( or mm)

1.000

13. Auxiliary Axis Parameter

II - 339

< Operation parameter group 4 >

No. Name Details Setting range Default value

174 Aspeed4 Operation parameter group 4 Automatic operation speed

Set the feedrate during automatic operation when operation parameter group 4 is selected.

1 to 100000 (/min or mm/min)

5000

175 Mspeed 4

Operation parameter group 4 Manual operation speed

Set the feedrate during manual operation or JOG operation when operation parameter group 4 is selected.

1 to 100000 (/min or mm/min)

2000

176 time4.1 Operation parameter group 4 Acceleration /deceleration time constant 1

Set the linear acceleration/deceleration time for the operation parameter group 1 automatic operation speed (clamp speed) when operation parameter group 4 is selected. When operating at speeds less than the clamp speed, the axis will linearly accelerate/decelerate at the inclination determined above. When this is set together with acceleration/deceleration time constant 2, S-shape acceleration/deceleration is carried out. In this case, set the acceleration/deceleration time of the linear part in this parameter.

1 to 9999 (ms) 100

177 time4.2 Operation parameter group 4 Acceleration /deceleration time constant 2

Set this parameter when carrying out S-shape acceleration/deceleration. When S-shape acceleration/deceleration is carried out, set the total time of the non-linear parts. When 1 is set in this parameter, linear acceleration/deceleration is carried out. In the handle feed operation mode, this set value is regarded as the time constant for the linear acceleration/deceleration.

1 to 9999 (ms) 1

13. Auxiliary Axis Parameter

II - 340

No. Name Details Setting range Default value

178 TL4 Operation parameter group 4 Torque limit value

Set the motor output torque limit value when operation parameter group 4 is selected. At the default value, the torque is limited at the maximum torque of the motor specifications. Set the default value when torque limit is not especially required. In the stopper method initializing mode in absolute position detection systems, this becomes the torque limit value during stopper operation.

1 to 500 (%) 500

179 OD4 Operation parameter group 4 Excessive error detection width

Set the excessive error detection width when operation parameter group 4 is selected. An excessive error alarm (S03 0052) is detected when the position droop becomes larger than this setting value. In the stopper method initializing mode in absolute position detection systems, this becomes the excessive error detection width during stopper operation.

0 to 32767 ( or mm)

100

180 just4 Operation parameter group 4 Set position output width

The signal indicating that the machine position is at any one of the stations is the set position reached (JST) signal. During automatic operation, the automatic set position reached (JSTA) signal is also output under the same conditions. Set the tolerable values at which these signals are output when operation parameter group 4 is selected. These signals turn OFF when the machine position is separated from the station by more than this value.

0.000 to 99999.999 ( or mm)

0.500

181 near4 Operation parameter group 4 Near set position output width

The signal indicating that the machine position is near any one of the station positions is the near set position (NEAR) signal. Set the tolerable values at which these signals are output when operation parameter group 4 is selected. These values are generally set wider than the set position output width. During operations, this is related to special commands when the station selection is 0.

0.000 to 99999.999 ( or mm)

1.000

13. Auxiliary Axis Parameter

II - 341

No. Name Details Setting range Default value

190 stpos2 Station 2 coordinate value

191 stpos3 Station 3 coordinate value

192 stpos4 Station 4 coordinate value

193 stpos5 Station 5 coordinate value

194 stpos6 Station 6 coordinate value

195 stpos7 Station 7 coordinate value

196 stpos8 Station 8 coordinate value

197 stpos9 Station 9 coordinate value

Set the coordinate value of each station when non-uniform assignment is selected. The station 1 coordinate value is fixed at 0.000 (machine coordinate zero point).

-99999.999 to 99999.999 ( or mm)

0.000

200 PSWcheck PSW detection method

This is a HEX setting parameter. Set bits without a description to their default values.

bit F E D C B A 9 8 7 6 5 4 3 2 1 0

Default value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

bit Position switch Meaning when "0" is set Meaning when "1" is set 0 PSW1 1 PSW2 2 PSW3 3 PSW4 4 PSW5 5 PSW6 6 PSW7 7 PSW8

The position switch output is judged by the machine position of the command system.

The position switch output is judged by the machine FB position (actual position).

8 9 A B C D E F

13. Auxiliary Axis Parameter

II - 342

No. Name Details Setting range Default value

201 202

PSW1dog1 PSW1dog2

PSW1 area setting 1 PSW1 area setting 2

203 204

PSW2dog1 PSW2dog2

PSW2 area setting 1 PSW2 area setting 2

205 206

PSW3dog1 PSW3dog2

PSW3 area setting 1 PSW3 area setting 2

207 208

PSW4dog1 PSW4dog2

PSW4 area setting 1 PSW4 area setting 2

209 210

PSW5dog1 PSW5dog2

PSW5 area setting 1 PSW5 area setting 2

211 212

PSW6dog1 PSW6dog2

PSW6 area setting 1 PSW6 area setting 2

213 214

PSW7dog1 PSW7dog2

PSW7 area setting 1 PSW7 area setting 2

215 216

PSW8dog1 PSW8dog2

PSW8 area setting 1 PSW8 area setting 2

When the machine position is in the region between region settings 1 and 2, the position switch of each No. will turn ON. Whether the value of setting 1 is larger than setting 2 (vice versa) does not affect the position switch operation. For rotation axes, the output turns ON at the region without including 0.000 degree.

-99999.999 to 99999.999 ( or mm)

0.000

220 push Stopper amount

Set the command stroke of the stopper operation during stopper positioning operations.

0.000 to 359.999 ( or mm)

0.000

221 pusht1 Stopper standby time

Set the standby time from the stopper starting coordinate positioning to the stopper operation start during stopper positioning operations.

0 to 9999 (ms) 0

222 pusht2 Stopper torque release time

Set the time from the completion of the stopper operation to the changeover of the stopper torque during stopper positioning operations.

0 to 9999 (ms) 0

223 pusht3 Set position signal output delay time

Set the time from the completion of the stopper operation to the output of the automatic set position reached (JSTA), set position reached (JST), and near set position (NEAR) signals during stopper positioning operations.

0 to 9999 (ms) 0

Revision History

Date of revision Manual No. Revision details

Jul. 1997 BNP-B2201* First edition created.

May 2000 BNP-B2201B(C) Addition (modification) Addition or modification of M64 additional parameters and alarms Addition of M65 and M66 parameters and alarms Correction of parameter names

Sept. 2001 BNP-B2201D The contents revised to correspond to M64AS, M64S, M65S and M66S. Miswrite is corrected Design of the cover and the back cover were changed. Manual name changed from "MELDAS 64/65/66 Alarm/Parameter Manual" to

"MELDAS 60/60S Series Alarm/Parameter Manual". MODEL, MODEL CODE, and Manual No. were added on the back cover.

Apr. 2002 BNP-B2201E Revisions to comply with M60S Series Version B0 Mistakes corrected

Feb. 2003 BNP-B2201G Servo alarm and spindle alarm names were standardized. Servo parameters were overall reviewed. (Chapter 7 to 9 Chapter 7) Revisions to comply with M60S Series Version B3 Mistakes corrected.

May 2004 BNP-B2201H Revised to comply with M60S system software versions C0, C1.

Jun. 2005 BNP-B2201J Revised to comply with M60S system software versions C5.

Dec. 2009 BNP-B2201L Corrected the items below. -#1284 ext20 bit0: Spindle speed clamp check -P134 G96 G96 Clamp Err. -M01 1043 No spindle speed clamp Corrected the mistakes.

Global Service Network

AMERICA EUROPE

MITSUBISHI ELECTRIC AUTOMATION INC. ( AMERICA FA CENTER) MITSUBISHI ELECTRIC EUROPE B.V. (EUROPE FA CENTER) Central Region Service Center GOTHAER STRASSE 10, 40880 RATINGEN, GERMANY 500 CORPORATE WOODS PARKWAY, VERNON HILLS, IL., 60061, U.S.A. TEL: +49-2102-486-0 / FAX: +49-2102-486-5910 TEL: +1-847-478-2500 / FAX: +1-847-478-2650

Germany Service Center Western Michigan Service Satellite KURZE STRASSE. 40, 70794 FILDERSTADT-BONLANDEN, GERMANY ALLEGAN, MICHIGAN., 49010, U.S.A. TEL: + 49-711-3270-010 / FAX: +49-711-3270-0141 TEL: +1-847-478-2500 / FAX: +1-269-673-4092

France Service Center Ohio Service Satellite 25, BOULEVARD DES BOUVETS, 92741 NANTERRE CEDEX FRANCE LIMA, OHIO, 45801, U.S.A. TEL: +33-1-41-02-83-13 / FAX: +33-1-49-01-07-25 TEL: +1-847-478-2500 / FAX: +1-847-478-2650

France (Lyon) Service Satellite Minnesota Service Satellite 120, ALLEE JACQUES MONOD 69800 SAINT PRIEST RICHFIELD, MINNESOTA, 55423, U.S.A. TEL: +33-1-41-02-83-13 / FAX: +33-1-49-01-07-25 TEL: +1-847-478-2500 / FAX: +1-847-478-2650

Italy Service Center Western Region Service Center VIALE COLLEONI 7-PALAZZO SIRIO CENTRO DIREZIONALE COLLEONI, 5665 PLAZA DRIVE, CYPRESS, CALIFORNIA, 90630, U.S.A. 20041 AGRATE BRIANZA MILANO ITALY TEL: +1-714-220-4796 / FAX: +1-714-229-3818 TEL: +39-039-60531-342 / FAX: +39-039-6053-206

Eastern Region Service Center Italy (Padova) Service Sattelite 200 COTTONTAIL LANE SOMERSET, NEW JERSEY, 08873, U.S.A. VIA SAVELLI 24 - 35129 PADOVA ITALY TEL: +1-732-560-4500 / FAX: +1-732-560-4531 TEL: +39-039-60531-342 / FAX: +39-039-6053-206

Western Pennsylvania Service Satellite U.K. Service Center ERIE, PENNSYLVANIA, 16510, U.S.A. TRAVELLERS LANE, HATFIELD, HERTFORDSHIRE, AL10 8XB, U.K. TEL: +1-814-897-7820 / FAX: +1-814-987-7820 TEL: +44-1707-27-6100 / FAX: +44-1707-27-8992

Southern Region Service Center Spain Service Center 2810 PREMIERE PARKWAY SUITE 400, DULUTH, GEORGIA, 30097, U.S.A. CTRA. DE RUBI, 76-80-APDO. 420 TEL: +1-678-258-4500 / FAX: +1-678-258-4519 08190 SAINT CUGAT DEL VALLES, BARCELONA SPAIN

TEL: +34-935-65-2236 / FAX: +34-935-89-1579 Northern Texas Service Satellite 1000, NOLEN DRIVE SUITE 200, GRAPEVINE, TEXAS, 76051, U.S.A. Poland Service Center TEL: +1-817-251-7468 / FAX: +1-817-416-5000 UL.KRAKOWSKA 50, 32-083 BALICE, POLAND

TEL: +48-12-630-4700 / FAX: +48-12-630-4727 Southern Texas Service Satellite FRIENDSWOOD, TEXAS, 77546, U.S.A Poland (Wroclaw) Service Center TEL: +1-832-573-0787 / FAX: +1-678-573-8290 UL KOBIERZYCKA 23,52-315 WROCLAW,POLAND

TEL: +48-71-333-77-53 / FAX: +48-71-333-77-53 Central Florida Service Satellite SATELITE BEACH, FLORIDA, 32937, U.S.A. Turkey Service Center TEL : +1-321-610-4436 / FAX : +1-321-610-4437 BAYRAKTAR BULVARI, NUTUK SOKAK NO:5, YUKARI DUDULLU

ISTANBUL, TURKEY Canadian Region Service Center TEL: +90-216-526-3990 / FAX: +90-216-526-3995 4299 14TH AVENUE MARKHAM, ONTARIO, L3R OJ2, CANADA TEL: +1-905-475-7728 / FAX: +1-905-475-7935 Czech Republic Service Center

TECHNOLOGICKA 374/6,708 00 OSTRAVA-PUSTKOVEC, CZECH REPUBLIC Mexico City Service Center TEL: +420-59-5691-185 / FAX: +420-59-5691-199 MARIANO ESCOBEDO 69 TLALNEPANTLA, 54030 EDO. DE MEXICO TEL: +52-55-9171-7662 / FAX: +52-55-9171-7649 Russia Service Center

213, B.NOVODMITROVSKAYA STR., 14/2, 127015 MOSCOW, RUSSIA Monterrey Service Satellite TEL: +7-495-748-0191 / FAX: +7-495-748-0192 ARGENTINA 3900, FRACC. LAS TORRES, MONTERREY, N.L., 64720, MEXICO TEL: +52-81-8365-4171 / FAX: +52-81-8365-4171 Sweden Service Center

STRANDKULLEN, 718 91 FROVI, SWEDEN Brazilian Service Center TEL: +46-581-700-20 / FAX: +46-581-700-75 ACESSO JOSE SARTORELLI, KM 2.1 CEP 18550-000, BOITUVA-SP, BRAZIL TEL: +55-15-3363-9900 / FAX: +55-15-3363-9911 Bulgaria Service Center

4 A. LYAPCHEV BOUL., 1756 - SOFIA, BULGARIA Brazilian's Sites Service Center TEL: +359-2-8176000 / FAX: +359-2-9744061 CITIES OF PORTO ALEGRE AND CAXIAS DO SUL BRAZIL CITIES OF SANTA CATARINA AND PARANA STATES Ukraine (Kharkov) Service Center TEL: +55-15-3363-9927 APTEKARSKIY PEREULOK 9-A, OFFICE 3, 61001 KHARKOV, UKRAINE

TEL: +38-57-732-7744 / FAX: +38-57-731-8721

Ukraine (Kiev) Service Center 4-B, M. RASKOVOYI STR., 02660 KIEV, UKRAINE TEL: +38-044-494-3355 / FAX: +38-044-494-3366

Belarus Service Center 703, OKTYABRSKAYA STR., 16/5, 220030 MINSK, BELARUS TEL: +375-17-210-4626 / FAX: +375-17-227-5830

South Africa Service Center P.O. BOX 9234, EDLEEN, KEMPTON PARK GAUTENG, 1625 SOUTH AFRICA TEL: + +27-11-394-8512 / FAX: +27-11-394-8513

ASEAN CHINA

MITSUBISHI ELECTRIC ASIA PTE. LTD. (ASEAN FA CENTER) MITSUBISHI ELECTRIC AUTOMATION (SHANGHAI) LTD. (CHINA FA CENTER) Singapore Service Center China (Shanghai) Service Center 307 ALEXANDRA ROAD #05-01/02 MITSUBISHI ELECTRIC BUILDING SINGAPORE 159943 4/F ZHI FU PLAZA, NO. 80 XIN CHANG ROAD, TEL: +65-6473-2308 / FAX: +65-6476-7439 SHANGHAI 200003,CHINA

TEL: +86-21-2322-3030 / FAX: +86-21-2322-2800 Indonesia Service Center China (Ningbo) Service Dealer WISMA NUSANTARA 14TH FLOOR JL. M.H. THAMRIN 59, JAKARTA 10350 INDONESIA China (Wuxi) Service Dealer TEL: +62-21-3917-144 / FAX: +62-21-3917-164 China (Jinan) Service Dealer

Malaysia (KL) Service Center China (Beijing) Service Center 60, JALAN USJ 10 /1B 47620 UEP SUBANG JAYA SELANGOR DARUL EHSAN, MALAYSIA 9/F, OFFICE TOWER 1, HENDERSON CENTRE, 18 JIANGUOMENNEI AVENUE TEL: +60-3-5631-7605 / FAX: +60-3-5631-7636 DONGCHENG DISTRICT, BEIJING, CHINA 100005

TEL: +86-10-6518-8830 / FAX: +86-10-6518-8030 Malaysia (Johor Baru) Service Center China (Beijing) Service Dealer No. 16, JALAN SHAH BANDAR 1, TAMAN UNGKU TUN AMINAH, 81300 SKUDAI, JOHOR MALAYSIA TEL: +60-7-557-8218 / FAX: +60-7-557-3404 China (Tianjin) Service Center

B-2-801-802, YOUYI BUILDING. 50 YOUYI ROAD, HEXI DISTRICT Vietnam Service Center-1 TIANJIN, CHINA 300061 47-49 HOANG SA ST. DAKAO WARD, DIST. 1, HO CHI MINH CITY, VIETNAM TEL: +86-22-2813-1015 / FAX: +86-22-2813-1017 TEL: +84-8-910-4763 / FAX: +84-8-910-2593 China (Shenyang) Service Satellite

Vietnam Service Center-2 China (Chengdu) Service Center THUAN KIEN PLAZA 190 HONG BANG ROAD.TOWER C. SUITE 3002. DIST.5, BLOCK B-1, 23F, CHUAN XIN MANSION, 18 SECTION 2 HO CHI MINH CITY,VIETNAM RENMIN ROAD (SOUTH), CHENGDU, SICHUAN, CHINA 610016 TEL: +84-8-240-3587 / FAX: +84-8-726-7968 TEL: +86-28-8619-9730 / FAX: +86-28-8619-9805

Vietnam (Hanoi) Service Center China (Changchun) Service Satellite 5TH FL., 93B KIM LIEN ST., PHUONG LIEN WARD, DONG DA DIST. BING 3RD ROAD., INDUSTRIAL&ECONOMICAL DEVELOPMENT ZONE, CHAOYANG DISTRICT TEL: +84-8-573-7646 / FAX: +84-4-573-7650 TEL : +86-0431-5021-546 / FAX : +86-0431-5021-690

Philippines Service Center China (Shenzhen) Service Center UNIT No.411, ALABAMG CORPORATE CENTER KM 25. WEST SERVICE ROAD ROOM 2512-2516, GREAT CHINA INTERNATIOANL EXCHANGE SQUARE, JINTIAN RD.S., SOUTH SUPERHIGHWAY, ALABAMG MUNTINLUPA METRO MANILA, PHILIPPINES 1771 FUTIAN DISTRICT, SHENZHEN, CHINA 518034 TEL: +63-2-807-2416 / FAX: +63-2-807-2417 TEL: +86-755-2399-8272 / FAX: +86-755-8218-4776

MITSUBISHI ELECTRIC AUTOMATION (THAILAND) CO., LTD. (THAILAND FA CENTER) BANG-CHAN INDUSTRIAL ESTATE No.111 SOI SERITHAI 54 KOREA T.KANNAYAO, A.KANNAYAO, BANGKOK 10230, THAILAND TEL: +66-2906-8255 / FAX: +66-2906-3239 MITSUBISHI ELECTRIC AUTOMATION KOREA CO., LTD. (KOREA FA CENTER)

Korea Service Center Thailand Service Center 1480-6, GAYANG-DONG, GANGSEO-GU SEOUL 157-200 ,KOREA 898/19,20,21,22 S.V. CITY BUILDING OFFICE TOWER 1 FLOOR 7 TEL: +82-2-3660-9602 / FAX: +82-2-3664-8668 RAMA III RD BANGPONGPANG,YANNAWA,BANGKOK 10120. THAILAND TEL: +66-2-682-6522 / FAX: +66-2-682-9750 Korea Taegu Service Satellite

603 CRYSTAL BUILDING 1666, SANBYEOK-DONG, BUK-KU, DAEGU, 702-010, KOREA TEL: +82-53-604-6047 / FAX: +82-53-604-6049

INDIA

MITSUBISHI ELECTRIC ASIA PVT LTD TAIWAN FIRST & SECOND FLOOR, AVR BASE, MUNICIPAL No.BC-308, HENNURE BANASWADI ROAD, HRBR RING ROAD, BANGALORE-560 043,INDIA MITSUBISHI ELECTRIC TAIWAN CO., LTD(TAIWAN FA CENTER) TEL: +91-80-4020-1600 / FAX: +91-80-4020-1699 TAIWAN (Taichung) Service Center

No.8-1, GONG YEH 16TH RD., TAICHUNG INDUSTRIAL PARK TAICHUNG CITY, TAIWAN R.O.C India (Pune) Service Center TEL: +886-4-2359-0688 / FAX: +886-4-2359-0689 EL-3, J BLOCK, M.I.D.C., BHOSARI PUNE 411026, INDIA TEL: +91-20-2710-2000 / FAX: +91-20-2710-2185 TAIWAN (Taipei) Service Center

3TH. FLOOR, No.122 WUKUNG 2ND RD., WU-KU HSIANG, TAIPEI HSIEN, TAIWAN R.O.C India (Bangalore) Service Center TEL: +886-2-2299-2205 / FAX: +886-2-2298-1909 S 615, 6TH FLOOR, MANIPAL CENTER, BANGALORE 560001, INDIA TEL: +91-80-509-2119 / FAX: +91-80-532-0480 TAIWAN (Tainan) Service Center

2F(C),1-1, CHUNGHWA-RD, YONGKANG CITY, TAINAN HSIEN, TAIWAN R.O.C India (Delhi) Service Center TEL: +886-6-313-9600 / FAX: +886-6-313-7713 1197, SECTOR 15 PART-2, OFF DELHI-JAIPUR HIGHWAY BEHIND 32nd MILESTONE GURGAON 122001, INDIA TEL: +91-98-1024-8895

OCEANIA

MITSUBISHI ELECTRIC AUSTRALIA LTD. Oceania Service Center 348 VICTORIA ROAD, RYDALMERE, N.S.W. 2116 AUSTRALIA TEL: +61-2-9684-7269 / FAX: +61-2-9684-7245

Notice

Every effort has been made to keep up with software and hardware revisions in the contents described in this manual. However, please understand that in some unavoidable cases simultaneous revision is not possible. Please contact your Mitsubishi Electric dealer with any questions or comments regarding the use of this product.

Duplication Prohibited This instruction manu

Manualsnet FAQs

If you want to find out how the CNC Meldas 60 Mitsubishi Electric works, you can view and download the Mitsubishi Electric CNC Meldas 60, 60S Series Users Manual v2 on the Manualsnet website.

Yes, we have the User's Manual for Mitsubishi Electric CNC Meldas 60 as well as other Mitsubishi Electric manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Mitsubishi Electric CNC Meldas 60. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Mitsubishi Electric CNC Meldas 60, 60S Series Users Manual v2 is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Mitsubishi Electric CNC Meldas 60, 60S Series Users Manual v2 consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Mitsubishi Electric CNC Meldas 60, 60S Series Users Manual v2 free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Mitsubishi Electric CNC Meldas 60, 60S Series Users Manual v2, simply download the document to your computer. Once downloaded, open the PDF file and print the Mitsubishi Electric CNC Meldas 60, 60S Series Users Manual v2 as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.