This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.
Warranty Exclusion of loss in opportunity and secondary loss from warranty liability Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation to: (1) Damages caused by any cause found not to be the responsibility of
Mitsubishi. (2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi
products. (3) Special damages and secondary damages whether foreseeable or not,
compensation for accidents, and compensation for damages to products other than Mitsubishi products.
(4) Replacement by the user, maintenance of on-site equipment, start-up test run and other tasks.
For safe use This product has been manufactured as a general-purpose part for general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life. Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi Electric. This product has been manufactured under strict quality control. However when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Safety Pr Before using t introduced in th product correct The precaution In this manu "CAUTION".
Depending on linked to seriou In any case, it i
DESIGN PRE
Some failur An externa which may Not doing s
DESIGN PRE
Do not bun or other wi them a min malfunction
MOUNTING PRECAUTION
Make sure before conn Failure to d
WIRING PREC
Be sure to system bef damage or
Please ma power supp GOT. Not d
after ing so
ng the
ighten
g can
gling, e to a
cable
1. Overview This cable connects Handy GOT and the Connector Conversion Box.
External dimensions
ide connector
e locked after
ch)
)
Control panel or operation panel
PLC
Handy GOT
External cable GT16H-C -37PE
GT16H-CNB-37S Connector Conversion Box
About 140 (5.52")
n box side
: mm (inch)
L 45 (1.77")
71 (2
.8 ")
16 (0.63")
2.2 Removal procedure 1) Check that the 24 V DC power to the external cable is OFF. 2) Pull up the lock lever with inserting a flat-blade screwdriver into the release
hole of the lock lever.
3) The external cable can be removed by pulling the whole plug connector while shifting the coupling of the plug connector to the cable side.
3. Operating ambient temperature Use the product within the following range. 0 to 40C
3. Temprature ambiante de fonctionnement Ce produit doit tre utilis dans les conditions suivantes. 0 et 40C
Flat screwdriver
Coupling
G
This manual de read this manu handling and o safety informat And, store this whenever nece Registration The company n registered trade
Effective April 2 Specifications a
o can cause an accident due to false output or malfunction.
CAUTIONS
dle the control and communication cables with main-circuit, power ring. Run the above cables separately from such wiring and keep imum of 100mm (3.94in.) apart.Not doing so noise can cause a .
S
to turn OFF the power switch in the Connector Conversion Box ecting or disconnecting an external cable.
o so may cause unit failure or malfunctions.
AUTIONS
shut off all phases of the external power supply used by the ore wiring. Failure to do so may result in an electric shock, product malfunctions. ke sure to ground FG terminal of the Connector Conversion Box ly section by applying 100 or less which is used exclusively for the oing so may cause an electric shock or malfunction.
: Indispensable manual For the manuals relevant to GOT2000/GOT1000, refer to the PDF manuals stored in the screen design software used. For details about a PLC to be connected, refer to the manuals of PLCs respectively.
Referenced Standard: GB/T15969.2 (Requirement of Chinese standardized law) Bundled Items
Applicable GOTs
Version1 creation method
GT16 Handy GOT User's Manual (Hardware/Utility, Connection)1/2, 2/2
JY997D41201 JY997D41202
(09R821)
Describes the Handy GOT hardware- relevant content such as part names, external dimensions, mounting, power supp ly w i r ing , spec i f i ca t i ons , and introduction to option devices.
Bundled item Quantity
GT16H-C -37PE cable ( : 30(3m), 60(6m), 100(10m)) 1
GT2506/GT16 Handy GOT External Cable Users Manual (This manual) 1
Abbreviations Model name
GOT 2000 GT25 Handy GOT GT2506HS-VTBD
GOT 1000 GT16 Handy GOT GT1655HS-VTBD
3) After inserting the connector, push the lock lever. The connectors ar the lever is pushed into.
ecaution (Read these precautions before using.) his product, please read this manual and the relevant manuals is manual carefully and pay full attention to safety to handle the
ly. s given in this manual are concerned with this product. al, the safety precautions are ranked as "WARNING" and
circumstances, procedures indicated by "CAUTION" may also be s results. s important to follow the directions for usage.
Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.
CAUTIONS
es of the GOT or cable may keep the outputs on or off. l monitoring circuit should be provided to check for output signals lead to a serious accident.
Certification of UL, cUL standards UL, cUL Standards are recognized in use by the following combination. GT2506HS-VTBD GT1665HS-VTBD GT16H-CNB-37S External cable (GT16H-C30-37PE, GT16H-C60-37PE, GT16H-C100-37PE) General notes on power supply This equipment must be supplied by a UL Listed or Recognized 24 V DC rated power supply and UL Listed or Recognized fuse rated not higher than 4A, or a UL Listed Class 2 power supply. Related Manuals When using the external cable, prepare the following manual as well. As GT16 Handy GOT User's Manual is sold separately, inquire at our local distributor for it.
portion. Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault.
DISPOSAL PRECAUTIONS
When disposing of the product, handle it as industrial waste.
Manual name Manual Number (Model Code) Contents
GOT2000 Series User's Manual (Hardware)
SH-081194ENG (1D7MJ5)
Describes the GOT hardware relevant content such as part names, external dimensions, mounting, power supply wiring, specifications, and introduction to option devices
GOT2000 Series Handy GOT Connection Manual For GT Works3
SH-081867ENG (1D7MS9)
Describes system configurations of the connec t ion me thod app l i cab le to GOT2000 Series Handy GOT and cable
2. Installing and removing of external cable
2.1 Installation procedure of external cable 1) Check that the 24 V DC power to the external cable is OFF. 2) Insert the connector adjusting the triangle marks of the main unit s
and cable side connector.
Value of Length L mm (in
30 3000 (118.1)
60 6000 (236.2)
100 10000 (393.7
Connector conversio
Unit
Handy GOT side M2.6
9.4 (0.37") ame and the product name to be described in this manual are the marks or trademarks of each company.
020 re subject to change without notice.
2013 MITSUBISHI ELECTRIC CORPORATION
Side A
Side B
JAPANESE
ENGLISHSide B
JY997D51001F
WIRING PRECAUTIONS
Correctly wire the Connector Conversion Box power supply section confirming the rated voltage and terminal arrangement of the GOT. Not do can cause a fire or failure.
Exercise care to avoid foreign matter such as chips and wire offcuts enteri GOT. Not doing so can cause a fire, failure or malfunction.
WIRING PRECAUTIONS
Plug the communication cable into the connector of the connected unit and t the mounting and terminal screws in the specified torque range. Undertightening can cause a short circuit or malfunction. Overtightenin cause a short circuit or malfunction due to the damage of the screws or unit.
STARTUP/MAINTENANCE PRECAUTIONS
The cables connected to the unit must be run in ducts or clamped. Not doing so can cause the unit or cable to be damaged due to the dan motion or accidental pulling of the cables or can cause a malfunction du cable connection fault.
When unplugging the cable connected to the unit, do not hold and pull the
T2506/GT16 Handy GOT External Cable
User's Manual
scribes the