Logik L16VUR11 Instruction Manual PDF

Bagless Upright Vacuum Cleaner

Instruction Manual L16VUR11

L16VUR11_IB_110927_Filter Frame.indd 1 27/09/2011 3:22 PM

L16VUR11_IB_110927_Filter Frame.indd 2 27/09/2011 3:22 PM

Contents

Unpacking ..................................................................................................................................4

Overview ....................................................................................................................................5 Front View ............................................................................................................................................................. 5 Back View............................................................................................................................................................... 5

Getting Started ..........................................................................................................................6 Handle Release .................................................................................................................................................... 6 Using the Mains Cable Holders ..................................................................................................................... 6

How to Start ...............................................................................................................................7

Carpet Height Adjustment ........................................................................................................8 Suggested Pile Height Setting....................................................................................................................... 8 Suggested Settings............................................................................................................................................ 8

Removing and Emptying the Dust Tank ..................................................................................9

Cleaning the HEPA Dust Tank Filter .......................................................................................10

Cleaning the HEPA Filter Frame ..............................................................................................11

Changing and Cleaning the Pre-motor Filter ........................................................................12

Changing and Cleaning the Exhaust Filter ............................................................................13

Cleaning the Dust Tank ...........................................................................................................14

Motor Thermostat....................................................................................................................15

Cleaning and Changing the Belt ............................................................................................16

Cleaning the Lower Hose ........................................................................................................17

Hints and Tips ..........................................................................................................................18

Specifications ...........................................................................................................................18

Safety Warnings .......................................................................................................................19

L16VUR11_IB_110927_Filter Frame.indd 3 27/09/2011 3:22 PM

The Main Unit Instruction Manual (P.N.: L16VUR11-003)

Dust Tank Cover (P.N.: 35029550001)

HEPA Filter (P.N.: 35029550002)

Filter Sealing (P.N.: 35029550003)

Unpacking Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to local regulations.

The following items are included:

Thank you for purchasing your new Logik Bagless Upright Vacuum Cleaner. We recommend that you spend some time reading this instruction manual in order to fully understand all the operational features it offers. You will find some hints and tips to help you resolve any issues. Read all the safety instructions carefully before using vacuum cleaner and keep this manual for future reference.

If items are missing or damaged, please contact Partmaster (UK only). Tel: 0844 800 3456 for assistance.

HEPA Filter Frame (P.N.: 35029550004)

Dust Tank (P.N.: 35029550005)

4

L16VUR11_IB_110927_Filter Frame.indd 4 27/09/2011 3:22 PM

Dust Tank Cover

HEPA Filter

HEPA Filter Frame

Filter sealing

Dust Tank

Trap Door

Product Overview

Front View Back View

1. Extendable Handle

2. Carrying Handle

3. Main Body

4. Dust Tank Assembly Release Button

5. Carpet Height Adjustment Knob

6. Power Head

7. Belt Windows

8. Mains Cable Hook

9. On/Off Switch

10. Mains Cable Holder

11. Mains Cable

12. Power Head Release Pedal

13. Handle Release Button

14. Lower Hose Blockage Clean Out

15. Dust Tank Assembly

CORD CUP

1

2

3

5

6

12

11

8

9

10

15

7

14

134

5

L16VUR11_IB_110927_Filter Frame.indd 5 27/09/2011 3:22 PM

Getting Started

Handle Release

Using the Mains Cable Holders 1. To quick release the mains cable, simply rotate the upper and lower mains cable holder

reverse direction to unwrap the mains cable. Hang the unwrapped mains cable to the mains cable hook before using the vacuum cleaner.

CORD CUP

Mains Cable Holder

CORD CUP

Mains Cable Hook

2. To store the mains cable, make sure that the upper mains cable holder is in an upright position, and the lower one in a downward position. Wrap the mains cable into place by wrapping in a clockwise direction around at the lower mains cable holder first. Dont over tighten the mains cable as this may cause damage to the mains cable.

CORD CUP

Handle Release Button

Before getting start, you may need to insert the handle into the main unit. Push down firmly until handle locks into place.

1. Press the handle release button, then lift the handle to an upright position, the handle will lock automatically.

2. To lower the handle, press the handle release button, and lower the handle.

6

L16VUR11_IB_110927_Filter Frame.indd 6 27/09/2011 3:22 PM

How to Start 1. Turn the mains cable holder down reverse to release the mains cable.

2. Plug the mains cable into the mains socket.

3. Lift up the handle and then depress on the handle release pedal to release the unit.

Handle Release Pedal

4. Select the appropriate carpet height. (See carpet height adjustment)

5. Switch the On/Off Switch to the I position to turn the vacuum cleaner on.

CORD CUP

On/Off Switch

7

L16VUR11_IB_110927_Filter Frame.indd 7 27/09/2011 3:22 PM

Special care is required when vacuuming certain types of carpet or floor covering. Always check the carpet or floor covering manufacturers recommended cleaning instructions before vacuuming.

Carpet Height Adjustment This upright vacuum cleaner can be used on multiple types of carpeting, bare floors or upholstery. To select a pile height setting:

1. Make sure the unit is off and the unit at its upright position.

2. Set the handle to the vertical and locked position.

3. Release the unit by pressing handle release button.

4. Select a pile height setting by turning the carpet height adjustment knob to the desired setting.

Carpet Height Adjustment Knob

Suggested Pile Height Setting You may need to choose a higher setting to make some jobs easier, such as vacuuming scatter rugs and longer pile carpets.

Suggested Settings PLUSH (HIGHEST): shag carpet, long pile, plush scatter rugs - medium to long pile.

BARE (LOWEST): short to medium pile, bare floors very low pile, bare floors. Place vacuum cleaner in PLUSH setting when using attachments to prevent possible floor damage.

8

L16VUR11_IB_110927_Filter Frame.indd 8 27/09/2011 3:22 PM

To obtain the best result from your cleaner the dust tank needs to be cleaned regularly, otherwise the airflow and cleaning power will be reduced. When the performance deteriorates it is necessary to clean the dust tank. Check if there are any blockages in the accessories or tubes and follow the filter cleaning instructions for optimum performance.

Removing and Emptying the Dust Tank

To reduce the risk of electric shock, the power cord must be disconnected before removing the dust tank, dust tank filter, changing the filters or performing maintenance/trouble shooting checks. The Dust Tank must always be emptied when the dirt level reaches the MAX line on the dust tank to have the best performance.

1. Press the dust tank assembly release. 2. To remove the dust tank assembly lift it out from the vacuum cleaner using the handle.

3. To empty the dust tank, open the trap door by pressing the trap door release button.

4. Close the trap door and return the dust tank assembly back to the unit.

P L U S H

B A R E

Dust Tank Assembly Release

Trap Door Release Button

Trap Door

9

L16VUR11_IB_110927_Filter Frame.indd 9 27/09/2011 3:22 PM

4. Alternatively, the HEPA filter may also be washed by running it under the tap. We recommend that you wash the filter once a week or when the suction appears to have been reduced. Always allow 24 hours for drying before inserting back into the vacuum cleaner.

3. Vigorously tap the HEPA filter on a hard surface until no more dust is can be seen falling out.

2. Remove the washable HEPA filter from the dust tank by turning the cover anti-clockwise.

Cleaning the HEPA Dust Tank Filter

Please Note the washable HEPA dust tank filter will stop most of the tiniest dust particles and airborne allergens from re-entering the air you breathe. In fact it stops 99.97% of all particles as small as 0.3 microns - many times smaller than a human hair! Because of this incredible filtration performance, the HEPA dust tank filter will quickly accumulate many fine dust particles inside the white filter folds that are difficult to see but which will eventually block or reduce your suction power, if not cleaned properly.

The white material in the HEPA filter will discolor over time. This is NORMAL and will NOT affect the performance of the filter.

Never overfill the dust tank. Remove dirt and clean the HEPA filter each time the dust tank is emptied. Failure to keep the filter clean could result in the motor becoming damaged.

1. To remove the HEPA filter, unlock and remove the dust tank cover by turning the cover anti-clockwise until the arrow on the cover aligns with the arrow on the handle and then lift the cover off.

HEPA Filter

Unlock position Lock position

10

L16VUR11_IB_110927_Filter Frame.indd 10 27/09/2011 3:22 PM

Unlock position

Unlock position

Lock position

Lock position

2. Unlock and remove the filter frame from the dust tank by turning the dust tank anti-clockwise until the arrow on the filter frame aligns with the arrow on the dust tank and then lift the filter frame off.

Cleaning the HEPA Filter Frame 1. Unlock and remove the dust tank cover by

turning the cover anti-clockwise until the arrow on the cover aligns with the arrow on the handle and then lift the cover off.

3. Rinse the frame in lukewarm water by running it under the tap to remove any dust that is adhering to the frame. Do NOT place in dishwasher.

4. Make sure that the filter frame is completely dry before reinserting back into the dust tank. Insert the filter frame, make sure it aligns with the arrow and stopper of the dust tank, lock the dust tank by turning the dust tank clockwise.

5. Reassemble and lock the dust tank cover by turning the cover clockwise until the arrow on the cover aligns with the arrow on the handle.

Stopper

Stopper

11

L16VUR11_IB_110927_Filter Frame.indd 11 27/09/2011 3:22 PM

4. Remove the pre-motor filter and clean in warm soapy water. Ensure the filter is totally dry before assembly.

Changing and Cleaning the Pre-motor Filter

Never use the vacuum cleaner without the motor filter protection and exhaust filter installed, otherwise damage to the vacuum cleaner may occur.

Failure to keep the filters clean, will result in a loss of performance.

Inserting wet filters into the vacuum cleaner will create an electrical hazard.

1. Unplug the vacuum cleaner from the mains.

2. Press the dust tank assembly release.

P L U S H B A R E

Pre-Motor Filter

5. Reinsert the filter and dust tank.

3. Pull the dust tank out from the vacuum cleaner.

P L U S H

B A R E

Dust Tank Assembly Release

12

L16VUR11_IB_110927_Filter Frame.indd 12 27/09/2011 3:22 PM

3. Remove the exhaust filter from the filter cover. Clean it in warm soapy water. Ensure the exhaust filter is totally dry before assembly.

Changing and Cleaning the Exhaust Filter 1. Unplug the vacuum cleaner from the mains.

2. Remove the filter cover from the vacuum cleaner.

P L U S H B A R E

Exhaust Filter

Filter Cover

4. Reinsert the exhaust filter and filter cover.

We recommend cleaning the pre-motor filter and exhaust filter at the same time and at regular intervals.

Inserting wet filters into the vacuum cleaner will create an electrical hazard.

P L U S H B A R E

Filter Cover

13

L16VUR11_IB_110927_Filter Frame.indd 13 27/09/2011 3:22 PM

5. Clean the dust tank in warm soapy water. Ensure the dust tank is totally dry before assembly.

3. Unlock and remove the dust tank cover by turning the cover anti-clockwise until the arrow on the cover aligns with the arrow on the handle and then lift the cover off.

4. Unlock and remove the filter frame from the dust tank by turning the dust tank anti-clockwise.

Cleaning the Dust Tank

Never use the vacuum cleaner without the dust tank installed, otherwise damage to the vacuum cleaner may occur.

1. Unplug the vacuum cleaner from the mains.

2. Pull the dust tank assembly out from the vacuum cleaner.

Dust Tank

Dust Tank Assembly

Unlock position Lock position

Stopper

14

L16VUR11_IB_110927_Filter Frame.indd 14 27/09/2011 3:22 PM

We recommend cleaning the dust tank at regular periods. Inserting a wet dust tank into the vacuum cleaner will create an electrical hazard.

6. Reassemble and lock the dust tank cover by turning the cover clockwise until the arrow on the cover aligns with the arrow on the handle. Then reinsert back into the vacuum cleaner.

Motor Thermostat This vacuum cleaner is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the vacuum cleaner off.

1. Switch Off the vacuum cleaner at once.

2. Disconnect the plug from the mains. Find the source of the overheating problem. (i.e. clogged hose or filter) If a clogged hose or filter is found, unclog the hose and replace the filters. Wait at least 45 minutes before attempting to reuse the vacuum cleaner.

3. After the vacuum cleaner has cooled down for 45 minutes, plug in the cleaner and turn it On. The vacuum cleaner should start again. If the vacuum cleaner fails to operate or the thermostat switches the vacuum cleaner off again, return it to your nearest service centre for examination or repair.

Unlock position Lock position

15

L16VUR11_IB_110927_Filter Frame.indd 15 27/09/2011 3:22 PM

Cleaning and Changing the Belt Should the drive belt become worn or slips you can replace with the drive belt.

1. Switch Off the vacuum cleaner and unplug from the mains.

2. Make sure the vacuum cleaner is locked in its upright position

3. Carefully lie the vacuum cleaner down and remove the 4 fixing screws. Ensure you keep all the screws in a safe place.

Drive Belt

Rolling Rod

Roller Brush

Only use the right belt. Using another belt could create a hazard and would invalidate the warranty.

4. Take off the cover of the power head starting from the back of the power head.

5. Remove the roller brush lifting it firmly upwards to release it.

6. Slide out the belt from the rolling rod.

7. Replace the worn out drive belt with a new one (not included) . Place the new belt drive onto the rolling rod. Carefully stretch the new belt over the roller brush and ensure it is correctly fitted before reinserting the roller brush.

8. Refit the cover in the same way using the 4 fixing screws.

Fixing ScrewsFixing Screws

16

L16VUR11_IB_110927_Filter Frame.indd 16 27/09/2011 3:23 PM

Cleaning the Lower Hose If rubbish is blocked inside the lower hose, press in the tab (avoid using sharp or pointed tool) and pull the lower hose down. Remove the blockage. Reconnected the hose.

The hose must be connected while vacuuming, other wise it will not pickup dust.

CORD CUP

17

L16VUR11_IB_110927_Filter Frame.indd 17 27/09/2011 3:23 PM

Hints and Tips

Problem Solution

Vacuum cleaner does not work

Not properly plugged into mains socket. Plug in firmly.

No electricity in mains wall socket. Check fuse or breaker.

On/Off switch not turned on. Push on/off switch to on.

Motor thermostat activated. Wait 45 mins for motor thermostat to reset.

The Suction performance is reduced.

Full or clogged dust cup. Clean dust cup.

Wrong pile height setting. Adjust the carpet height setting.

Clogged nozzle or dust inlet port. Remove obstruction.

Clogged hose. Remove obstruction.

Broken belt. Replace with a new one.

Host not inserted fully. Push hose in securely.

Dirty HEPA filters. Clean/HEPA filters.

Rubbish blocking the lower hose. Clean the lower hose.

Cleaner picks up moveable rugs or is hard to push

Wrong carpet height setting. Adjust the setting.

Agitator does not turn

Broken belt. Replace the belt.

Belt installed incorrectly. Check the belt is clean and does not need changing.

Specifications

Model L16VUR11

Voltage 230 ~ 240V ~ 50Hz

Power Consumption 1200-1400W 1600W (MAX)

Dust Tank Capacity 2.2 Litres

18

L16VUR11_IB_110927_Filter Frame.indd 18 27/09/2011 3:23 PM

Safety Warnings For your continued safety and to reduce the risk of injury or electric shock, please follow all the safety precautions listed below. Read all the instructions carefully before using the appliance and keep them for future reference. Retain the manual. If you pass the appliance onto a third party make sure

to include this manual. Check that the voltage marked on the rating label matches your mains voltage. Consult your dealer if you are ever in doubt about the installation, operation

or safety of your appliance. Do not remove any fixed cover as this may expose dangerous voltages. Do not allow electrical appliance to be exposed to dripping or splashing. To protect against electrical shock, do not immerse mains cable, mains plug, or any part of the

appliance in water or other liquid. Never suck up water or any other liquid. Never suck up flammable substances and do not suck up

ashes until they are cold. Never use the appliance without the motor protection filter. This damages the

motor and shortens the life of the appliance. If a blockage is found in the brushes, hoses or tubes, it should be removed before use. Do not store or use the appliance close to high temperature places. Do not run over the mains cable with the appliance. Close supervision is necessary when any appliance is used by or near children. This appliance is not intended for use by persons (including children) with reduced sensory or

mental capabilities, or lack of experience and knowledge unless they have been given supervision or instructions concerning the use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Do not point the hose, tube or any other accessories at the eyes, ears or mouth during operation.

Allow the appliance to cool completely before cleaning or storing. Do not use the appliance for other uses than its intended use. The use of accessories not recommended by the appliance manufacturer may

cause injuries. Do not use the appliance outdoors. Do not operate an appliance with a damaged mains cable or mains plug, or in an abnormal state.

If the mains cable is damaged it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.

Do not continue to operate the appliance if you are in any doubt about it working normally (e.g. abnormal noise, smell, smoke), or if it is damaged in any way - switch off, withdraw the mains plug and consult your dealer.

Any maintenance and repair must be handled by a professional technician. Do not try to repair by yourself.

19

L16VUR11_IB_110927_Filter Frame.indd 19 27/09/2011 3:23 PM

DSGRetailLtdMaylandsAvenueHemelHempstead

HertsHP27TGEngland

This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU.

For more information, please contact the local authority or your retailer where you purchased the product.

(P.N.: L16VUR11-003)

Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories. With over 1 million spares and accessories available we can deliver direct to your door the very

next day. Visit www.partmaster.co.uk or call 0844 800 3456 (UK customers only). Calls charged at National Rate.

NOTE: If you require a replacement for any of the items listed below, please quote their corresponding part numbers:

Replacement Part Part Number

Dust Tank Cover 35029550001

HEPA Filter 35029550002

Filter Sealing 35029550003

HEPA Filter Frame 35029550004

Dust Tank 35029550005

L16VUR11_IB_110927_Filter Frame.indd 20 27/09/2011 3:23 PM

L16VUR11_IB_110927_Filter Frame.indd 21 27/09/2011 3:23 PM