Logik L1USBS10 Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Logik L1USBS10 Instruction Manual PDF

DSG Retail Ltd Maylands Avenue Hemel Hempstead Herts HP2 7TG England

GB-4 GB-5

Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories. With over 1 million spares and accessories available

we can deliver direct to your door the very next day. Visit www.partmaster.co.uk or call 0844 800 3456 (UK customers only) Calls charged at National Rate.

This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product.

SPECIFICATIONS

Adapter input: 100-240V~ 50/60Hz 0.15A Adapter output: 5Vdc 0.15A Battery pack: 1 x NiMH 1.2V 800mAh Charging time: 8 hours

We continually strive to improve our products, specifications may change without prior notice.

SAFETY FIRST!

For your continued safety and to reduce the risk of injury or electric shock, please follow all the safety precautions listed below.

The outer foil is very thin. If handled improperly, it can be easily damaged. To avoid personal injury, do not use the shaver if it has a damaged foil or inner cutter.

Both the foil and the blade have a limited service life. To keep a better result, we suggest you to replace the outer foil and the inner cutter at regular intervals.

This shaver is only to be used in dry conditions.

Clean the shavers body by using a cloth dampened with soapy water.

Do not forget to turn o the shaver to prevent depleting the batteries life.

If the shaver is not working properly, have it inspected by the dealer or an authorized service center.

Always use your shaver for its intended use, as described in this manual.

Please make sure that the old batteries are disposed of at an ocially assigned location.

Do not leave this shaver within the reach of children.

Please keep the manual for future reference.

Do not handle with wet hands.

Do not store in a damp environment.

Do not use this appliance with a damaged or broken foil, as serious facial injuries may occur.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning the use of the appliance by a person responsible for their safety.

Warning : Keep the appliance dry.

Children should be supervised to ensure that they do not play with the appliance.

The mains socket must be located near the appliance and should be easily accessible.

USB Shaver

Congratulations on the purchase of your new Logik USB Shaver.

We recommend that you spend some time reading this instruction manual in order to fully understand all the operational features it offers.

Read all the safety instructions carefully before use and keep this instruction manual for future reference.

Instruction Manual L1USBS10

Notes for battery disposal Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed of with normal household waste. Please inform yourself about the local rules on separate collection of batteries. The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health.

This unit has a rechargeable battery Do not throw away the appliance with the normal household waste at the

end of its life, but hand it in at an ocial collection point for recycling. By doing this, you help to preserve the environment.

The built-in rechargeable battery contains substances that may pollute the environment. Always remove the battery before you discard and hand in the appliance at an ocial collection point. Dispose of the battery at ocial collection point for batteries.

Do not attempt to replace the battery.

NOTE: If you require a replacement for any of the items listed below, please quote their corresponding part numbers:

Replacement Part

Protective Cap

Outer Foil

Foil Frame

Inner Cutter

USB Cable

Mains Adapter

Travel Case

Cleaning Brush

L1USBS10-0002

L1USBS10-0003

L1USBS10-0004

L1USBS10-0005

L1USBS10-0006

L1USBS10-0007

L1USBS10-0008

L1USBS10-0009

Part Number

(P.N. L1USBS10-002)

GB-1 GB-2 GB-3

UNPACKING

Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to local regulations. The following items are included: The Main Unit The USB Cable (P.N.: L1USBS10-0006) The Mains Adapter (P.N.: L1USBS10-0007) The Travel Case (P.N.: L1USBS10-0008) The Cleaning Brush (P.N.: L1USBS10-0009) The Instruction Manual (P.N.: L1USBS10-002) If items are missing, or damaged please contact Partmaster (UK only). Tel: 0844 800 3456 for assistance.

FIRST TIME USE

Before using the shaver for the first time, please follow the steps below, 1. Operate the shaver for 2 minutes. 2. Push both side of the foil frame release button and detach the foil frame as

shown. 3. Wipe the lubricate o both the outer foil and inner cutter. Your shaver is now ready to use. Please note that the shaver requires a little time to get used to, because your skin and beard need about a month to adjust to any new shaving method. Charge the shaver for 8 hours before first time use.

PRODUCT OVERVIEW

OPERATION

1. Remove the protective cap. 2. Switch the shaver on by pressing the release button

and pushing the power switch upward. 3. Hold the shaver at a right angle (90) to your skin. Start

shaving by applying gentle pressure to your face. Stretch your skin with your free hand, move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaving method. Applying excessive pressure will not provide a closer shave.

CHARGING YOUR SHAVER

Charging using the mains adapter 1. Please make sure that the power is o before charging. 2. Plug the mains adapter into the mains socket and then connect the USB

Interfaces of the shaver to the mains adapter (included) to recharge the shaver. 3. The charging indicator will illuminate.

CLEANING AND MAINTENANCE

1. Switch o the shaver. 2. Push both side of the foil frame release button

and detach the foil frame as shown.

MAINTENANING THE CUTTING SYSTEM

1. It is recommended that you replace the outer foil at least every year and the inner cutter at least every two years to maintain your shavers performance.

2. Turn the shaver o before replacing the outer foil and the inner cutter.

Replacing the outer foil : Squeeze the foil frame release button and lift the foil frame upwards to remove it. Remove the outer foil from the frame by slipping it o the hooks. Slip the new outer foil into the frame with the plastic edge facing inward. Guide the plastic edges onto the hooks in the frame.

Replacing the inner cutter : Remove the outer foil frame. Remove the inner cutter by grasping it firmly at both ends and pulling it straight away from the shaver. To insert the new inner cutter, hold the cutter at both ends and press downwards until its snaps onto the shaver.

The charging indicator will illuminate red during charging. You will get approx 1 hours of shaving time from a full charge. It take approx 8 hours to fully charge the shaver. If you frequently charge the shaver for more than 10 hours, the battery

capacity will reduced. Do not operate the shaver while it is charging.

Do not immerse the unit in water.

1

2

3

4

5 10

12

13

9

6 7

8

1

2

3

4

5

6

7

Protective Cap Outer Foil Foil Frame Inner Cutter Foil Frame Release Button Power Switch Release Button

8

9

10

11

12

13

Charging Indicator USB Interface USB Cable Mains Adapter Travel Case Cleaning Brush

4. Switch the shaver o by pushing the switch downwards. 5. To prevent damage to the foil and inner cutter, cover the unit with the

protective cap every time you have finished using the shaver.

90 90

3. Grasp inner cutter firmly at each side, and pull straight up. 4. Clean away the clippings with the cleaning brush provided.

5. Reassemble the shaver parts in the reverse order. (Bottom view)

Release Button Power Switch

Charging using the USB cable 1. Please make sure that the power is o before charging. 2. Connect the USB Interfaces of the shaver and computer with the USB cable

(included) for recharging. Make sure the computer is powered on. 3. The charging indicator will illuminate.

Manualsnet FAQs

If you want to find out how the L1USBS10 Logik works, you can view and download the Logik L1USBS10 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Logik L1USBS10 as well as other Logik manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Logik L1USBS10. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Logik L1USBS10 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Logik L1USBS10 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Logik L1USBS10 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Logik L1USBS10 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Logik L1USBS10 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.