Logik L200IR12 Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Logik L200IR12 Instruction Manual PDF

Thank you for purchasing your new Logik Steam Iron.

We recommend that you spend some time reading this instruction manual in order to fully understand all the operational features it offers.

Read all the safety instructions carefully before use and keep this instruction manual for future reference. DSG Retail Ltd. (co. no. 504877)

1 Portal Way, London, W3 6RS, UK

Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories. With over 1 million spares and accessories available we can deliver direct

to your door the very next day. Visit www.partmaster.co.uk or call 0344 800 3456 (UK customers only) Calls charged at National Rate.

IB-L200IR12-160226V3

Plug the iron into the mains socket. Set the highest settings on the Temperature

Dial and Steam Control. Unplug the iron once the Temperature

Indicator goes o, the iron should be held over a bowl before pressing and holding the Self Clean button immediately. Water will drain out with impurities.

Release the Self Clean button. Slightly tilt the iron to drain water out.

Plug the iron into the mains socket again. Set the highest settings on the Temperature Dial and iron on a damp cloth to remove deposits on the soleplate.

When the iron is cool: Open the Filler Door, invert the iron and pour away the excess water from the reservoir. When pouring away the water, gently shake the iron to remove any loose particles from the reservoir.

SPECIFICATIONS

Voltage Rating: 230V ~ 50Hz Power consumption: 2000W We continually strive to improve our products. Specications may change without prior notice.

SELF-CLEANING The self-cleaning feature cleans the inside of the plate, removing impurities. We recommend using it every 10-15days.

CAUTION! In between ironing always stand the iron in the

upright position. NEVER leave the iron face down. After you have finished ironing, turn the Steam

Control to the OFF position. Unplug the iron from the mains socket. Stand the iron in its upright position and allow it to completely cool down.

AFTER YOU HAVE FINISHED IRONING Move the Steam Control to the OFF position and switch the iron o at the mains socket and unplug. Stand the iron in the upright position and let the iron completely cool down.

self clean

GB-4 GB-5

Instruction Manual

2000 Watts Steam Iron L200IR12

SPRAY BUTTON Press the Spray button to spray water on the material. It may be used for steam or dry ironing.

To avoid staining, do not use the spray on silk or synthetics, and be very careful when you iron delicate fabrics.

To operate the spray and steam shot functions, the water reservoir must be at least one-quarter full. If these features stop working, ll the water reservoir.

VERTICAL STEAM Hold the iron upright and press the Shot of Steam button for vertical ironing. If the Temperature indicator illuminates, stop pressing the Shot of Steam button and wait for it to go o before using this feature again.

ANTI-DRIP SYSTEM This is designed to prevent water escaping from the soleplate when the iron is cold. During use, the anti drip system may click loudly, particularly when heating up or cooling down. This is perfectly normal and indicates that the system is functioning correctly.

ANTI-SCALE SYSTEM The built - in anti-scale cartridge is designed to reduce the build-up of lime scale which occurs during steam ironing and will prolong the working life of your iron. The anti-scale cartridge will not completely stop the natural process of lime scale build-up so always empty the water after use and self-clean the iron regularly.

SHOT OF STEAM BUTTON This feature may be used during steam or dry ironing only when the iron is at the highest settings on the temperature dial. Press the Shot of Steam button to release a powerful surge of steam. You may need to press the button a few times to prime the surge of steam. Wait a few seconds for the steam to penetrate the fabric before pressing the button again. Excessive use of this feature will cause the iron to cool, and the Temperature Indicator will illumi- nate. If this happens, wait for the Temperature Indica- tor to go o before using this feature again.

The symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop o your waste for recycling, please contact your local authority, or where you purchased your product.

For general information about this appliance and handy hints and tips, please visit

www.knowhow.com/knowledgebank or call 0344 5611234.

L200IR12_IB_RC_160226_grace.pdf 1 26/2/16 2:26 pm

OPERATION Ensure the mains socket is switched o and the

Steam Control is at the OFF position. Fill the iron with water as described above. Place the iron on its heel on the ironing board rest

and connect the mains cable to the mains socket. The Temperature Indicator will illuminate. Select the correct temperature by turning the

Temperature Dial.

Turn clockwise to increase and anticlockwise to reduce temperature.

Mains Cable Temperature

Indicator Spray

Shot of Steam Steam Control

Water Filler & Cap

Spray Nozzle

Water Tank

Temperature Dial

Self Clean

Soleplate

Filler Cup

UNPACKING Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations. The following items are included: Steam Iron Filler Cup Instruction Manual If items are missing or damaged, please contact Partmaster (UK only). Tel: 0344 800 3456 for assistance.

IRONING TEMPERATURES Check the ironing instructions attached to the article (they are on a label showing a symbol of an iron). Always follow these ironing instructions. The indications on the irons Temperature Dial and the table below will help you.

FIRST TIME USE Inspect the iron carefully. Check that the voltage marked on the rating matches your mains voltage. Remove any protective lm from the soleplate. Polish the soleplate lightly with a clean soft cloth to remove any residues. Place the iron on the ironing board or a at rigid surface.

PRODUCT OVERVIEW

m in

max

INCREASEDECREASE

20 0m

l

15 0m

l

10 0m

l

50 m

l

FILLING THE IRON Make sure the iron is unplugged from the mains socket and the Steam Control is at the OFF position. Open the Water Door, tip the iron up slightly and ll it carefully with fresh water using the supplied ller cup. If you live in a hard water area, it is advisable to use distilled or de-mineralised water. Avoid using water containing softeners, perfumes or additives.

Do not ll the iron above the max mark indicated on the side of the iron.

Do not iron garments that are dirty or stained. The irons heat may set the stain.

Some parts have been lightly greased and the iron might smoke slightly when switched on for the rst time. After a short while, this will cease. We recommend passing the iron over a clean cotton cloth before using it for the rst time. The Temperature Indicator will go o when the indicated setting reaches the correct temperature. The iron is now ready for use. During use the indicator will cycle on and o as the thermostat maintains the iron at the correct temperature setting.

In between operations and when filling the iron always stand the iron on its heel. NEVER leave the iron face down.

The iron gives o steam continuously only if you hold the iron horizontally. You can stop the continuous steam by placing the iron in a vertical position or by moving the steam selector to the OFF position.

SWITCHING OFF THE IRON To prevent water leakage, set to the far side of the Steam Control to prevent water leakage from the soleplate.

Set to the OFF position

STEAM IRONING Steam ironing should be carried out at the highest settings on the Temperature Dial. Steam ironing at lower temperatures may cause water to leak from the soleplate. The quantity of steam is regulated by the Steam Control. Move the steam selector to a suitable position depending on the quantity of steam required and the ironing temperature.

Maintaining the nish of the irons soleplate is essential. Keep the soleplate smooth: do not scratch it on metal objects (e.g. the edge of the ironing board, buttons, zippers, etc.) as these may impair performance.

If there are no ironing instructions but you know the fabric, then use the table above. The table is valid only for the actual materials and does not take into account any nish applied to the fabric. Textiles to which a nish has been applied (wrinkle relief, printed T shirts etc.) should be ironed at a lower temperature. If the fabric contains mixed bres, select the lowest ironing temperature of the composition, e.g. iron a 60% polyester /40% cotton mix at the temperature indicated for polyester. The iron heats up quicker than it cools down. Sort fabrics to be ironed into groups according to temperature: wool with wool, cotton with cotton, etc. Start by ironing articles requiring low temperature settings and progress to higher ones.

Pure (100%) wool fabrics may be pressed with the iron set to a steam position and the garment protected by a dry cloth.

GB-1 GB-2 GB-3

GARMENT LABEL

Synthetic

Silk-wool

Cotton-linen

Medium temperature

Low temperature

High temperature

FABRIC TYPE THERMOSTAT REGULATION

Fabric not to be ironed

MAX Steam MIN Steam Dry Ironing

(OFF)

SAFETY FIRST!

Please follow all the safety precautions listed below for safety and to reduce the risk of injury or electrical shock. Read all the instructions before operating the appliance and keep them for future

reference. If you pass the product on to a third party, include these instructions. Unplug the iron from the mains socket when not in use, and before emptying,

filling, or cleaning. Do not touch the soleplate of the iron if it is hot. Always hold the appliance by the handle. Keep the appliance well away from surfaces and objects that can be damaged by

heat. Ensure there is adequate room to operate the iron. Ensure that the iron cannot fall into water. Do not immerse the mains cable in any liquid. Do not let the mains cable overhang the edge of the work surface or allow it to

touch hot surfaces or sources of heat or flame. If any part of this appliance is damaged or malfunctions in any way, or the mains

cable or mains plug is broken, do not continue to use it. Seek expert assistant. The iron must not be used if dropped, if there are visible signs of damage or if it is

leaking. This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Keep the appliance and its cord out of reach of children less than 8 years old. Children should be supervised to ensure that they do not play with the appliance. Parents must warn children not to touch hot appliance parts. Close supervision is

necessary when an appliance is used near children. When not ironing never leave the iron face down. Stand it upright on its heel, on a

level heatproof surface. The iron must be used and rested on a stable surface. When standing the iron in an upright position ensure that the surface is flat and

stable. Do not use outdoors or in damp or wet conditions. Do not use this iron for professional laundry services. Do not use this appliance for any purpose not covered by the instructions. Do not turn the iron upside down, there may be hot water in the water tank. Use this iron only with a purpose-built ironing board. Observe all ironing instructions and ironing temperature dot settings given by the

garment manufacturer. These are normally on a label or labels inside the garment. If the mains cable is damaged it must be replaced by the manufacturer, its service

agent, or similarly qualified persons in order to avoid a hazard. The iron must not be left unattended while it is connected to the mains socket. Always ensure the water filling does not exceed th

Manualsnet FAQs

If you want to find out how the L200IR12 Logik works, you can view and download the Logik L200IR12 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Logik L200IR12 as well as other Logik manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Logik L200IR12. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Logik L200IR12 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Logik L200IR12 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Logik L200IR12 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Logik L200IR12 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Logik L200IR12 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.