Logik L10HC10 Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Logik L10HC10 Instruction Manual PDF

GB-4 GB-5

Hair Clipper Instruction Manual L10HC10

SAFETY FIRST! Please follow all the safety precautions listed below for safety and to reduce the risk of injury or electrical shock. Check if the voltage indicated on the appliances corresponds to the mains voltage

in your home before you connect the appliance. Do not damaged the appliance. Do not use the appliance when one of the attachments is damaged or broken as

this may cause injury. Keep the appliance out of the reach of children. Use and store the appliance at a temperature between 15c and 35c. Always unplug the appliance after use. This appliance is only intended for clipping human hair. Do not use it for any other

purpose. Do not immerse the appliance in water or any other liquid. Do not expose the appliance to excessive moisture, dust or dirt Always check the blades for alignment. Always add a few drops of oil before use. Do not use the appliance if the teeth are damaged. Always check the appliance for damage before use. If any damage is observed, do

not use the appliance. This appliance has no user repairable parts. The appliance can become hot during use , only use for 10 minutes ON 10 minutes

OFF three cycle . Always let the appliance cool down before storing. This appliance is for personal use only. It is not suitable for commercial use. This appliance should not be left unattended when switch on or when connected

to mains supply. Do not wrap the mains lead around the appliance when hot or when storing. Do not carry the appliance by the mains lead. Do not use with wet hands. Do not use the appliance on damaged or broken skin. The appliance should never be left unattended when connected to the mains

supply. Children should be supervised to ensure that they do not play with the appliance. This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning the use of the appliance by a person responsible for their safety.

If the mains cable is damaged it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.

WARNING : Keep the appliance dry.

SPECIFICATIONS Power supply : 230V~, 50Hz, AC Power Power Consumption : 10W We continually strive to improve our products, specifications may change without prior notice.

DGS Retail Ltd Maylands Avenue Hemel Hempstead Herts HP2 7TG England

Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories. With over 1 million spares and accessories available we can deliver direct to your door the very next day. Visit

www.partmaster.co.uk or call 0870 6001 338 (UK customers only) Calls charged at National Rate.

This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product.

Congratulations on the purchase of your new Logik Hair Clipper.

We recommend that you spend some time reading this instruction manual in order to fully understand all the operational features it offers.

Read all the safety instructions carefully before use and keep this instruction manual for future reference.

Unplug the hair clipper before you start cleaning it.

GB-1 GB-2 GB-3

UNPACKING Remove all packaging from the hair clipper. Retain the packaging. If you dispose of it please do so according to any local regulations. The following items are included: The Main Unit Four Comb Attachments:

3mm (1/8): (P.N.: RAY911-009) 6mm (1/4): (P.N.: RAY911-010) 9mm (3/8): (P.N.: RAY911-011) 12mm (1/2): (P.N.: RAY911-012)

The Teeth Guard (P.N.: RAY911-008) The Lubricating Oil (P.N.: RAY911-038) The Cleaning Brush (P.N.: RAY911-041) The Comb (P.N.: RAY911-013) The Scissors (P.N.: RAY913-056) Instruction Manual (P.N.: L10HC10-001) If items are missing or damaged, please contact Partmaster (UK only). Tel: 0870 6001 338 for assistance.

NOTE Your hair clipper has a power dial. It has already been adjusted for peak eciency before leaving the factory. However, if you experience the speed has decreased. You will need to adjust the dial. 1. Turn on the hair clipper. 2. Use a tool to insert into the power dial. 3. Gently turn the dial clockwise until you

hear the vibration sound noticeably increase.

4. Then turn slightly anticlockwise, stop as soon as the sound disappeares.

FIRST TIME USE 1. Make sure the Power switch is set to 0 (O). 2. Remove the plastic protective cover from the cutting blade. 3. Lubricate the cutting blades with a couple of drops of oil before using the unit for

the rst time and before using it on each further occasion. (Lubricating oil tip was sealed, open the tip with cutter or scissors.)

PRODUCT OVERVIEW

OPERATION Fitting comb attachments The hair clipper is supplied with 4 comb attachments that are used to trim the hair to one of 4 dierent lengths:

Comb is used to trim hair to a length of 3mm (1/8). Comb is used to trim hair to a length of 6mm (1/4). Comb is used to trim hair to a length of 9mm (3/8). Comb is used to trim hair to a length of 12mm (1/2).

Using the hair clipper without a comb attachment will cut o hair with cutting length of around 1.5mm. You can use the adjusting lever on the side of the hair clipper to control the amount of hair to be cut. Lower the lever down for less hair; raise the lever up for more hair. Slide one of the comb attachments over the head of the hair clippers fixed cutting blade.

Using the hair clipper 1. Before you start clipping, make sure the head of the person

whose hair you are cutting is at the same level as your chest. 2. To get the best results, use the hair clipper only on dry hair.

Do not use it on freshly washed hair. 3. First comb the hair into the direction of hair growth. 4. Switch power switch to I on position. 5. Always move the hair clipper against the direction of hair

growth, otherwise it will not cut the hair properly. 6. Move the hair clipper through the hair slowly.

Clipping with comb attachment 1. Slide the comb attachment onto the rails on the hair clipper. Select the small or large comb attachment, depending on

the desired hair length. 2. Make sure that the arms of the comb attachment have been

properly slid onto the rails on both sides. Hair length settings The hair length settings are indicated in millimetres on the

arms of the comb attachment. The settings correspond to the remaining hair length after cutting.

3. Start at the setting for maximum hair length. 4. Make sure that the flat part of the comb attachment is

always fully in contact with the scalp to obtain an even cutting result.

5. Pass the hair clipper slowly over the crown from dierent directions to achieve an even cutting result.

6. Make overlapping passes over the head to ensure that the hair clipper catches all the hairs that need to be cut.

7. Comb the hair in the direction of hair growth from time to time so that the hair clipper can catch the hair more easily.

8. To achieve a good result with curly, sparse or long hair, you can use a comb to guide the hair towards the hair clipper.

PRECISE CONTOURING WITHOUT COMB ATTACHMENT 1. Remove the comb attachment by pulling it o the hair clipper. 2. Before contouring the hairline round the ears, comb the hair ends over the ear. 3. Bend the person's ear to get it out of the way.

1

2

3

4

Comb Attachments

Power Dial

Teeth Guard

Comb

Lubricating Oil Cleaning Brush Scissors

1 2 3 4

4. Tilt the hair clipper in such a way that only one edge of the cutting element touches the hair ends.

5. Only cut the hair ends. The hairline should be close to the ear.

6. To contour the nape hairline and the sideburns, turn the hair clipper and make downward strokes.

7. Move slowly and smoothly. Just follow the natural hairline.

GRADUATION The hair clipper not only allows you to cut the hair evenly at the same length all over the head, it also enables you to achieve a smooth transition from longer hair on top of the head to shorter hair on the back and sides of the head. 1. Start clipping at the setting for maximum hair length. 2. Then choose a shorter setting and cut the hair on all parts of the head except the

top, where you want the hair to be longer. 3. You can repeat this procedure until the hair on every part of the head has the

desired length.

CUTTING OVER STYLING COMB OR FINGERS This technique can be used to obtain hair lengths over 41 mm and 21 mm. Bear in mind that this technique is dicult to master and should only be applied by experienced users. 1. Make sure the comb attachment is not attached to the

hair clipper. 2. Comb a small section of hair upwards. Lift the hair with a

styling comb or hold it between your ngers until only the length that needs to be cut sticks out.

3. Cut the hair protruding from the comb or fingers. 4. Continue this procedure and comb frequently to remove

cut hair and to check for unevenly cut sections.

CLEANING & STORAGE Clean the hair clipper after every time you use it. Do not use abrasives, scourers or liquids such as alcohol, petrol or acetone to clean the hair clipper. 1. Make sure the hair clipper is switched o and

unplugged. 2. Make sure the comb attachment is not attached to the

hair clipper. Never pull at the flexible top of the comb attachment. Always pull at the bottom part.

3. Push the middle part of the cutting unit upwards with your thumb until it opens and then pull it o the hair clipper. Be careful that the cutting unit does not fall to the floor.

4. Clean the cutting unit and the inside of the hair clipper with the brush supplied. 5. Place the lug of the cutting unit into the slot and push the unit back onto the hair

clipper ('click').

Hanging Loop

Cutting Blade

Adjustable Lever

Power Switch

Mains Cable

Manualsnet FAQs

If you want to find out how the L10HC10 Logik works, you can view and download the Logik L10HC10 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Logik L10HC10 as well as other Logik manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Logik L10HC10. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Logik L10HC10 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Logik L10HC10 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Logik L10HC10 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Logik L10HC10 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Logik L10HC10 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.