Linksys KVM2KIT Switch Installation Guide PDF

ProConnect Series

Use this Guide to install: KVM2KIT

Integrated KVM 2-Port Switch

Installation Guide

COPYRIGHT & TRADEMARKS Copyright 2003 Linksys, All Rights Reserved. ProConnect is a trademarks of Linksys. Linksys is a registered trademark of Linksys. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. All other trademarks and brand names are the property of their respective proprietors.

FCC STATEMENT The ProConnect Integrated KVM 2-Port Switch has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a res- idential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following meas- ures:

Reorient or relocate the receiving antenna Increase the separation between the equipment or device Connect the equipment to an outlet other than the receivers Consult a dealer or an experienced radio/TV technician for assistance

EC Declaration of Conformity (Europe)

In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and Amendment Directive 93/68/EEC, this product meets the requirements of the following standards:

EN55022 Emission EN55024 Immunity

IG-KVM2KIT-112102NC KL

x

Integrated KVM 2-Port Switch

1

Integrated KVM 2-Port Switch

3

Console One VGA, SVGA or Multisync Monitor Capable of the Highest Resolution

You Will Be Using on Either Computer One PS/2 Keyboard One PS/2 Mouse

Either Computer One VGA, SVGA, or Multisync Monitor Capable of the Highest

Resolution You Will Be Using on Either Computer One PS/2 Keyboard One PS/2 Mouse

A. Power down the monitor and computers before you install the KVM Switch. Unplug the power cords of any computers that have the Keyboard Power On function; otherwise, the KVM Switch will receive power from those com- puters. Then make sure all devices you are connecting are properly ground- ed.

B. Connect the monitors cable to the monitor port on the KVM Switch.

C. Connect the PS/2 keyboards cable to the PS/2 keyboard on the KVM Switch.

D. Connect the PS/2 mouses cable to the PS/2 mouse port on the KVM Switch.

System Requirements

ProConnect Series

Table of Contents System Requirements 3

Step 1: Install the Integrated KVM 2-Port Switch 3

Step 2: Use the Hot Key Combinations for the Integrated KVM 2-Port Switch 5

Specifications 8

Contact Information 9

2

Step 1: Install the Integrated KVM 2-Port Switch

This Installation Guide is meant to help you install the Integrated KVM 2-Port Switch quickly and easily. For additional information, visit the Linksys website at www.linksys.com Note: The connectors on the built-in cables are color-coded to match

the appropriate ports on your computers; however, double-check each connectors icon before you make the physical connection.

54

Integrated KVM 2-Port Switch

The KVM Switch is controlled by hot key commands, also known as keyboard shortcuts. Hot key commands allow you to conveniently access either comput- er directly from the keyboard. Using hot keys, you can manually toggle between computers or automatically cycle between computers at a preset time interval.

There are three basic hot key combinations:

Toggle to the Other Computer Initiate Auto Scan Mode Initiate Auto Scan Mode and Change the Scan Interval

Toggle to the Other Computer

To toggle between the two computers, press and release the Scroll Lock key twice.

Step 2: Use the Hot Key Combinations for the Integrated KVM 2-Port Switch

ProConnect Series

E. Use the PC 1 cable for the first PC you are connecting. Plug the cables monitor connector into PC 1s monitor port.

F. Plug the PC 1 cables keyboard connector into PC 1s keyboard port.

G. Plug the PC 1 cables mouse connector into the PC 1s mouse port.

H. Use the PC 2 cable for the second PC your are connecting. Repeat steps E- G.

I. Turn on the monitor and computers. The PC 1 LED will light up automati- cally, and PC 1 will be displayed on the monitor.

Your installation is complete. To learn about the hot key com- binations used to control the KVM Switch, proceed to step 2.

Initiate Auto Scan Mode and Change the Scan Interval

If you want to change the can interval, use the following hot key combination:

1. Press and release the left Shift key. 2. Press and release the right Shift key. 3. Press and release the s key. 4. Press and release the n key, n being a number from 1-4. Refer to the

Scan Interval Table.

For example, to initiate Auto Scan Mode and change the scan interval to 10 sec- onds, use this hot key combination:

7

Initiate Auto Scan Mode

The Auto Scan feature automatically cycles the KVM between both computers, so you can monitor their activity without manually switching between comput- ers. The factory default scan interval is three seconds.

To initiate Auto Scan Mode, press and release the left Shift key, and then press and release the right Shift key.

To exit Auto Scan Mode, press the spacebar.

6

Integrated KVM 2-Port SwitchProConnect Series

Integrated KVM 2-Port Switch

For help with installation or operation of this product, contact Linksys Technical Support at one of the phone numbers listed in the Technical Support insert or Internet addresses below:

E-mail Europe europe-support@linksys.com United Kingdom & Ireland uks@linksys.com Latin America latam-soporte@linksys.com U.S. and Canada support@linksys.com

For unlisted regions or updated contact information please visit the website below:

Web http://www.linksys.com/international

9

The letter n represents 1-4, depending on the scan interval you want. Refer to the Hot Key Summary Table.

Model Number: KVM2KIT

Standards: PS/2

Protocol: Microsoft PS/2 Protocol

Ports: Keyboard: 1 PS/2 female - Console

2 PS/2 male - CPU Mouse: 1 PS/2 female - Console

2 PS/2 male - CPU Monitor: 1 HD15 female - Console

2 HD15 male - CPU

LEDs: PC 1, PC 2

Scan Interval: 3, 5, 10, or 20 seconds (3 is default)

8

ProConnect Series

Contact Information