Contents

Lenovo IdeaPad K1 Tablet Hardware Maintenance Manual PDF

1 of 58
1 of 58

Summary of Content for Lenovo IdeaPad K1 Tablet Hardware Maintenance Manual PDF

IdeaPad Tablet K1

Hardware Maintenance Manual

Note: Before using this information and the product it supports, be sure to read the general information under Notices on page 53.

First Edition (May 2011) Copyright Lenovo 2011. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered pursuant a General Services Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. 2010 Lenovo

iii

Contents

About this manual ....................................... iv

Safety information ........................................ 1 General safety ................................................ 2 Electrical safety .............................................. 3 Safety inspection guide .................................. 5 Handling devices that are sensitive to electrostatic discharge .................................... 6 Grounding requirements ................................. 6 Safety notices: multilingual translations.......... 7 Laser compliance statement......................... 14

Important service information ................... 16 Strategy for replacing FRUs ......................... 16

Strategy for replacing a hard disk drive ............17 Important notice for replacing a system board ................................................................17

Important information about replacing RoHS compliant FRUs ............................................ 18

General checkout ...................................... 19 What to do first ............................................. 20 Power system checkout................................ 21

Checking the AC adapter .................................21 Checking the battery pack ...............................22

Related service information ...................... 23 Restoring the factory contents by using OneKey Recovery ........................................ 23

Restore of factory default .................................23 Using recovery discs.........................................23

Passwords .................................................... 24 Power-on password ..........................................24 Supervisor password .......................................24

Power management ..................................... 25 Screen blank mode ...........................................25 Sleep (standby) mode ......................................25 Hibernation mode .............................................26

Lenovo IdeaPad Tablet K1 ......................... 27 Specifications ............................................... 27 FRU replacement notices ............................. 29

Screw notices ..................................................29 Removing and replacing an FRU ................. 30

1010 Base cover ...............................................31 1020 Battery pack .............................................33 1030 Middle cover ............................................34 1040 Docking bracket .......................................35 1050 System board ............................................ 36 1060 Switch board, SD board and HDMI board ......................................................38 1070 Speaker ...................................................41

1080 Optical finger navigation (OFN) module .....42 1090 Panel support bracket ..............................43 1100 Integrated camera ....................................44 1110 Antenna assembly ....................................45

Locations ...................................................... 46 Front view and Right-side view .........................46 Bottom and Left-side view ...............................47

Parts list ........................................................ 48 Overall ..............................................................49 Miscellaneous parts ..........................................51 AC adapters ......................................................52

Notices......................................................... 53 Trademarks .................................................. 54

iv

About this manual

This manual contains service and reference information for the following Lenovo IdeaPad product:

Lenovo IdeaPad Tablet K1 Use this manual to troubleshoot problems. The manual is divided into the following sections:

The common sections provide general information, guidelines, and safety information required for servicing computers. The product-specific section includes service, reference, and product-specific parts information.

Important: This manual is intended only for trained servicers who are familiar with Lenovo IdeaPad products. Use this manual to troubleshoot problems effectively. Before servicing a Lenovo IdeaPad product, make sure to read all the information under Safety information on page 1 and Important service information on page 16.

1

Safety information

Safety information

This chapter presents the following safety information that you need to get familiar with before you service an IdeaPad Tablet K1 computer: General safety on page 2 Electrical safety on page 3 Safety inspection guide on page 5 Handling devices that are sensitive to electrostatic discharge on page 6 Grounding requirements on page 6 Safety notices: multilingual translations on page 7 Laser compliance statement on page 14

2

IdeaPad Tablet K1 Hardware Maintenance Manual

General safety Follow these rules below to ensure general safety:

Observe a good housekeeping in the area where the machines are put during and after the maintenance. When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt

to lift it. 4. Lift it by standing or pushing up with your leg muscles; this action could

avoid the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you.

Do not perform any action that causes hazards to the customer, or that makes the machine unsafe. Before you start the machine, make sure that other service representatives and the customer are not in a hazardous position. Place removed covers and other parts in a safe place, keeping them away from all personnel, while you are servicing the machine. Keep your toolcase away from walk areas so that other people will not trip it over. Do not wear loose clothing that can be trapped in the moving parts of the machine. Make sure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it. Insert the ends of your necktie or scarf inside clothing or fasten it with the nonconductive clip, about 8 centimeters (3 inches) from the end. Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing. Attention: Metal objects are good electrical conductors.

Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that may be hazardous to your eyes. After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective. Reinstall all covers correctly before returning the machine to the customer. Fan louvers on the machine help to prevent the overheating of internal components. Do not obstruct fan louvers or cover them with labels or stickers.

3

Safety information

Electrical safety Observe the following rules when working on electrical equipments.

Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges. Do not use such kind of mat to protect yourself from electrical shock.

Find the room emergency power-off (EPO) switch, disconnecting the switch or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly. Do not work alone under hazardous conditions or near the equipment that has hazardous voltages. Disconnect all power before: Performing a mechanical inspection Working near power supplies Removing or installing main units

Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position. If you need to work on a machine that has exposed electrical circuits, observe the following precautions: Ensure that another person, familiar with the power-off controls, is near

you. Attention: Another person must be there to switch off the power, if

necessary. Use only one hand when working with powered-on electrical equipment;

keep the other hand in your pocket or behind your back. Attention: An electrical shock can occur only when there is a complete

circuit. By observing the above rule, you may prevent a current from passing through your body.

When using testers, set the controls correctly and use the approved probe leads and accessories for that tester.

Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages; instructions for these precautions are in the safety sections of maintenance information. Be extremely careful when you measure the high voltages.

Regularly inspect and maintain your electrical hand tools for safe operational condition. Do not use worn or broken tools and testers. Never assume that power has been disconnected from a circuit. First, check it to make sure that it has been powered off.

4

IdeaPad Tablet K1 Hardware Maintenance Manual

Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. Do not service the following parts with the power on when they are removed from their normal operating places in a machine: Power supply units Pumps Blowers and fans Motor generators and similar units. (This practice ensures correct grounding of the units.)

If an electrical accident occurs: Caution: do not become a victim yourself. Switch off the power. Send the victim to get medical aid.

5

Safety information

Safety inspection guide The purpose of this inspection guide is to assist you in identifying potential unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards according to the attachment of non-Lenovo IdeaPad features or options not covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present: Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock) Explosive hazards, such as a damaged CRT face or a bulging capacitor Mechanical hazards, such as loose or missing hardware

To determine whether there are any potential unsafe conditions, use the following checklist at the beginning of every service task. Begin the checks with the power off, and the power cord disconnected.

Checklist: 1. Check exterior covers for damage (loose, broken, or sharp edges). 2. Turn off the computer. Disconnect the power cord. 3. Check the power cord for:

a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground.

b. The power cord should be the type specified in the parts list. c. Insulation must not be frayed or worn.

4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo IdeaPad alterations. Use good judgment

as to the safety of any non-Lenovo IdeaPad alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal

filings, contamination, water or other liquids, or signs of fire or smoke damage.

8. Check for worn, frayed, or pinched cables. 9. Check that the power-supply cover fasteners (screws or rivets) have not

been removed or tampered with.

6

IdeaPad Tablet K1 Hardware Maintenance Manual

Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.

Notes: 1. Use product-specific ESD procedures when they exceed the requirements

noted here. 2. Make sure that the ESD protective devices you use have been certified (ISO

9000) as fully effective.

When handling ESD-sensitive parts: Keep the parts in protective packages until they are inserted into the product. Avoid contact with other people. Wear a grounded wrist strap against your skin to eliminate static on your body. Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices. Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.

Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.

Attach the ESD ground clip to any frame ground, ground braid, or green- wire ground.

When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector- outside shells on these systems.

Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.

7

Safety information

Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish.

Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. Avant de remettre lordinateur sous tension aprs remplacement dune unit en clientle, vrifiez que tous les ressorts, vis et autres pices sont bien en place et bien fixes. Pour ce faire, secouez lunit et assurez-vous quaucun bruit suspect ne se produit. Des pices mtalliques ou des copeaux de mtal pourraient causer un court-circuit. Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, mu sichergestellt werden, da keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehuse vergessen wurden. Der Computer mu geschttelt und auf Klappergerusche geprft werden. Metallteile oder-splitter knnen Kurzschlsse erzeugen.

Prima di accendere lelaboratore dopo che stata effettuata la sostituzione di una FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e non siano sparse allinterno dellelaboratore. Verificare ci scuotendo lelaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi.

Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y dems piezas pequeas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Comprubelo agitando el sistema y escuchando los posibles ruidos que provocaran. Las piezas metlicas pueden causar cortocircuitos elctricos.

8

IdeaPad Tablet K1 Hardware Maintenance Manual

Safety notice 2

DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short- circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium. Ne les dmontez pas, ne les rechargez pas, ne les exposez ni au feu ni leau. Ne les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous la rglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle de lhorloge temps rel, veillez nutiliser que les modles cits dans la liste de pices dtaches adquate. Une batterie ou une pile inapproprie risque de prendre feu ou dexploser. Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.

Alcune batterie di riserva contengono una piccola quantit di nichel e cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nellacqua n cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria dellRTC (real time clock) o la batteria di supporto, utilizzare soltanto i tipi inseriti nellappropriato Catalogo parti. Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa.

Algunas bateras de reserva contienen una pequea cantidad de nquel y cadmio. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deschelas tal como dispone la normativa local. Utilice slo bateras que se encuentren en la lista de piezas. La utilizacin de una batera no apropiada puede provocar la ignicin o explosin de la misma.

9

Safety information

Safety notice 3

DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la dmontez pas, ne lexposez ni au feu ni leau. Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous la rglementation en vigueur. Lorsque vous remplacez la batterie, veillez nutiliser que les modles cits dans la liste de pices dtaches adquate. En effet, une batterie inapproprie risque de prendre feu ou dexploser. Akkus enthalten geringe Mengen von Nickel. Sie drfen nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.

La batteria contiene piccole quantit di nichel. Non smontarla, gettarla nel fuoco o nellacqua n cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria, utilizzare soltanto i tipi inseriti nellappropriato Catalogo parti. Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa.

Las bateras contienen pequeas cantidades de nquel. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deschelas tal como dispone la normativa local. Utilice slo bateras que se encuentren en la lista de piezas al sustituir la batera. La utilizacin de una batera no apropiada puede provocar la ignicin o explosin de la misma.

10

IdeaPad Tablet K1 Hardware Maintenance Manual

Safety notice 4

DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100C (212F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium. Elle prsente des risques dincendie, dexplosion ou de brlures graves. Ne la rechargez pas, ne retirez pas son connecteur polaris et ne la dmontez pas. Ne lexposez pas une temperature suprieure 100C, ne la faites pas brler et nen exposez pas le contenu leau. Mettez la pile au rebut conformment la rglementation en vigueur. Une pile inapproprie risque de prendre feu ou dexploser. Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entznden, explodieren oder schwere Verbrennungen hervorrufen. Batterien dieses Typs drfen nicht aufgeladen, zerlegt, ber 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.

La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa.

La batera de repuesto es una batera de litio y puede provocar incendios, explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte, ni caliente por encima de los 100C (212F), ni la incinere ni exponga el contenido de sus celdas al agua. Deschela tal como dispone la normativa local.

11

Safety information

Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau daffichage cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un mdecin si des symptmes persistent aprs le lavage. Die Leuchtstoffrhre im LCD-Bildschirm enthlt Quecksilber. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgem behandelt wird oder der Computer auf den Boden fllt. Wenn der Bildschirm beschdigt ist und die darin befindliche Flssigkeit in Kontakt mit Haut und Augen gert, sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgesplt und bei Beschwerden anschlieend ein Arzt aufgesucht werden.

Nel caso che caso lLCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero permanere.

Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos, lave inmediatamente las reas afectadas con agua durante 15 minutos como mnimo. Obtenga atencin medica si se presenta algn sntoma del fluido despues de lavarse.

12

IdeaPad Tablet K1 Hardware Maintenance Manual

Safety notice 6

DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin dviter tout risque de choc lectrique, ne retirez pas le cache en plastique protgeant la partie infrieure de la carte dalimentation. Aus Sicherheitsgrnden die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.

Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore.

Para evitar descargas, no quite la cubierta de plstico que rodea la parte baja de la tarjeta invertida.

Safety notice 7

DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. Bien que le voltage des batteries principales soit peu lev, le court-circuit ou la mise la masse dune batterie peut produire suffisamment de courant pour brler des matriaux combustibles ou causer des brlures corporelles graves. Obwohl Hauptbatterien eine niedrige Spannung haben, knnen sie doch bei Kurzschlu oder Erdung genug Strom abgeben, um brennbare Materialien zu entznden oder Verletzungen bei Personen hervorzurufen.

Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto circuito o a massa pu fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione.

Aunque las bateras principales tienen un voltaje bajo, una batera cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.

13

Safety information

Safety notice 8

DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unit remplaable en clientle, mettez le systme hors tension, dbranchez tous les cordons dalimentation des socles de prise de courant, retirez la batterie et dconnectez tous les cordons dinterface. Die Stromzufuhr mu abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt wird.

Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di interconnessione.

Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas de corriente elctrica, quite la batera y, a continuacin, desconecte cualquier cable de conexin entre dispositivos.

14

IdeaPad Tablet K1 Hardware Maintenance Manual

Laser compliance statement Some models of Lenovo IdeaPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.

If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note the following:

CAUTION Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure. O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposio radiao.

Pour viter tout risque dexposition au rayon laser, respectez les consignes de rglage et dutilisation des commandes, ainsi que les procdures dcrites. Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann gefhrliche Laserstrahlung auftreten.

Lutilizzo di controlli, regolazioni o lesecuzione di procedure diverse da quelle specificate possono provocare lesposizione a.

El uso de controles o ajustes o la ejecucin de procedimientos distintos de los aqu especificados puede provocar la exposicin a radiaciones peligrosas.

Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage device could result in exposure to hazardous laser radiation. There are no serviceable parts inside those drives. Do not open.

15

Safety information

A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following:

DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiao por raio laser ao abrir. No olhe fixo no feixe de luz, no olhe diretamente por meio de instrumentos ticos e evite exposio direta com o feixe de luz.

Rayonnement laser si carter ouvert. vitez de fixer le faisceau, de le regarder directement avec des instruments optiques, ou de vous exposer au rayon. Laserstrahlung bei geffnetem Gert. Nicht direkt oder ber optische Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden. Kinyitskor lzersugr ! Ne nzzen bele se szabad szemmel, se optikai eszkzkkel. Kerlje a sugrnyalbbal val rintkezst! Aprendo lunit vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici e evitare lesposizione diretta al fascio.

Radiacin lser al abrir. No mire fijamente ni examine con instrumental ptico el haz de luz. Evite la exposicin directa al haz.

16

IdeaPad Tablet K1 Hardware Maintenance Manual

Important service information

This chapter presents the following important service information: Strategy for replacing FRUs on page 16

Strategy for replacing a hard disk drive on page 17 Important notice for replacing a system board on page 17

Important information about replacing RoHS compliant FRUs on page 18

Important: BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site: http://consumersupport.lenovo.com/.

Strategy for replacing FRUs

Before replacing parts: Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual. After a system board is replaced, ensure that the latest BIOS is loaded to the system board before completing the service action. To download software fixes, drivers, and BIOS, follow the steps below: 1. Go to http://consumersupport.lenovo.com/. 2. Enter a serial number or select a product or use Lenovo smart downloading. 3. Select the BIOS/Driver/Applications and download. 4. Follow the directions on the screen and install the necessary software.

17

Important service information

Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs:

If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue. Some computers have both a processor board and a system board. If you are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one. If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs one by one to see if the symptoms change. Replace only the FRU that changed the symptoms.

Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect.

Strategy for replacing a hard disk drive Always try to run a low-level format before replacing a hard disk drive. This will cause all customer data on the hard disk to be lost. Make sure that the customer has a current backup of the data before performing this action. Attention: The drive startup sequence in the computer you are servicing may have been changed. Be extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect drive, data or programs can be overwritten.

Important notice for replacing a system board Some components mounted on a system board are very sensitive. Improper handling can cause damage to those components, and may cause a system malfunction. Attention: When handling a system board:

Do not drop the system board or apply any excessive force to it. Avoid rough handling of any kind. Avoid bending the system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.

18

IdeaPad Tablet K1 Hardware Maintenance Manual

Important information about replacing RoHS compliant FRUs

RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts. If the original FRU parts are non-compliant, replacement parts can also be non-compliant. In all cases if the original FRU parts are RoHS compliant, the replacement part must also be RoHS compliant.

Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified with unique FRU part numbers.

Lenovo plans to transit to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovos requirements and schedule in the EU. Products sold in 2005 and 2006 will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant FRUs.

RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS implementation date, failed RoHS compliant parts must always be replaced with RoHS compliant ones, so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs may be used.

Products marketed before June 2006 Products marketed after June 2006 Current or original part

Replacement FRU Current or original part

Replacement FRU

Non-RoHS Can be Non-RoHS

Must be RoHS Must be RoHS Non-RoHS Can be RoHS

Non-RoHS Can sub to RoHS

RoHS Must be RoHS

Note: A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of the order.

19

General checkout

General checkout

This chapter presents the following information: What to do first on page 20 Power system checkout on page 21

Before you go to the checkout, make sure to read the following important notes:

Important notes: Onlycertifiedtrainedpersonnelcanservicethecomputer. BeforereplacinganyFRU,readtheentirepageonremovingandreplacing FRUs.

WhenyoureplaceFRUs,usenewnylon-coatedscrews. Beextremelycarefulduringsuchwriteoperationsascopying,saving,or formatting. Drives in the computer that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be overwritten.

ReplaceanFRUonlywithanotherFRUof thecorrectmodel. When you replace an FRU, make sure that the machine model and the FRU part number are correct by referring to the FRU parts list.

AnFRUshouldnotbereplacedjustbecauseofasingle,unreproducible failure.Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. Consider replacing an FRU only when a problem recurs. If you suspect that an FRU is defective, clear the error logs and run the test again. If the error does not recur, do not replace the FRU.

BecarefulnottoreplaceanondefectiveFRU.

20

IdeaPad Tablet K1 Hardware Maintenance Manual

What to do first When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Procedure index and page number in which the failing FRU was detected 6. Failing FRU name and part number 7. Machine type, model number, and serial number 8. Customers name and address

Note for warranty: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer. The following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use. Before checking problems with the computer, determine whether the damage is covered under the warranty by referring to the following list:

The following are not covered under warranty: LCD panel cracked from the application of excessive force or from being dropped Scratched (cosmetic) parts Distortion, deformation, or discoloration of the cosmetic parts Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force Damage caused by liquid spilled into the system Damage caused by the improper insertion of a PC Card or the installation of an incompatible card Improper disc insertion or use of an optical drive Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive, or the insertion of a diskette with multiple labels Damaged or bent diskette eject button Fuses blown by attachment of a nonsupported device Forgotten computer password (making the computer unusable) Sticky keys caused by spilling a liquid onto the keyboard Use of an incorrect AC adapter on laptop products

The following symptoms might indicate damage caused by nonwarranted activities:

Missing parts might be a symptom of unauthorized service or modification. If the spindle of a hard disk drive becomes noisy, it may have been subjected to excessive force, or dropped.

21

General checkout

Power system checkout

If you suspect a power problem, see the appropriate one of the following power supply checkouts: Checking the AC adapter on page 21 Checking the battery pack on page 22

Checking the AC adapter You are here because the computer fails only when the AC adapter is used.

If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity and installation.

To check the AC adapter, follow the steps below: 1. Unplug the AC adapter cable from the tablet. 2. Measure the output voltage at the plug of the AC adapter cable. See the

following figure:

Voltage (V DC)

+20

0

Pin

1

2

1

2

Note: Output voltage for the AC adapter pin No. 2 may differ from the one you are servicing. 3. If the voltage is not correct, replace the AC adapter. 4. If the voltage is acceptable, do the following:

Replace the system board. If the problem continues, go to Lenovo IdeaPad Tablet K1 on page 27.

Note: Noise from the AC adapter does not always indicate a defect.

22

IdeaPad Tablet K1 Hardware Maintenance Manual

Checking the battery pack Battery charging does not start until the Power Meter shows that less than 95% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life.

To check your battery, move your cursor to the Power Meter icon in the icon tray of the Windows taskbar and wait for a moment (but do not click it), and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon.

Note: If the battery pack becomes hot, it may not be able to be charged. Remove it from the computer and leave it at room temperature for a while. After it cools down, reinstall and recharge it.

To check the battery pack, follow the steps below: 1. Turn off the computer. Follow the removal steps in 1020 Battery pack on

page 33 in Removing and replacing an FRU on page 30. 2. Measure the voltage between battery terminals 1 (+) and 14 (-). See the

following figure:

Terminal

1 +0 to +8.4

14 Ground (-)

Voltage (V DC)

14(-)13(-)

10 9 8 7

4(+) 3(+) 2(+) 1(+)

12(-) 11(-)

5 6

3. If the voltage is less than +11.0 V DC, the battery pack has been discharged.

Note: Recharging will be continued for at least 3 hours, even though the indicator does not light on.

If the voltage is still less than +11.0 V DC after recharging, replace the battery.

4. If the voltage is more than +11.0 V DC, measure the resistance between battery terminals 5 and 7. The resistance must be 4 to 30 K.

If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system board.

23

Related service information

Related service information

This chapter presents the following information: Restoring the factory contents by using OneKey Recovery on page 23 Passwords on page 24 Power management on page 25

Restoring the factory contents by using OneKey Recovery

Restore of factory default The IdeaPad Tablet K1 computers come with pre-installed OneKey Rescue System. In order to save application files and the initial backed up files of the system, the hard disk in a Lenovo computer includes a hidden partition when it is shipped. If you need to restore the system to the point of your first boot up, just enter Lenovo OneKey Rescue System and run Restore to factory default. For details of OneKey Rescue System, see the User Guide for OneKey Rescue System.

Note: This will delete all the new data on the system partition (C drive), which is not recoverable. Make sure to back up your critical data before you perform this action.

Using recovery discs When you replace a hard disk drive in your computer, you are unable to use the pre-installed Lenovo OneKey Recovery and OneKey Rescue. However, you can use the recovery discs that store your backed up data to restore your new hard drive to a previous backup status.

Note: You can create recovery discs by burning the backup image to a CD/DVD as recovery discs. For details of Createrecoverydiscs, see the User Guide for OneKey Rescue System.

24

IdeaPad Tablet K1 Hardware Maintenance Manual

When you use the recovery discs to boot your computer, the system will enter the user interface for system recovery automatically. Please follow the prompt to insert the backup discs to complete the whole recovery process.

Note: The recovery process might take up to 2 hours.

Passwords

As many as two passwords may be needed for any Lenovo IdeaPad computer: the power-on password (POP) and the supervisor password (SVP). If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered. Exception: If only an SVP is installed, the password prompt does not appear when the operating system is booted.

Power-on password A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted.

Supervisor password A supervisor password (SVP) protects the system information stored in the BIOS Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration.

Attention: If the SVP has been forgotten and cannot be made available to the servicer, there is no service procedure to reset the password. The system board must be replaced for a scheduled fee.

25

Related service information

Power management

Note: Power management modes are not supported for APM operating system.

To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby), and hibernation.

Screen blank mode If the time set on the Turn off monitor timer in the operating system expires, the LCD backlight turns off. You can also turn off the LCD backlight by pressing Power button.

To end screen blank mode and resume normal operation, press Power button.

Sleep (standby) mode When the computer enters sleep (standby) mode, the following events occur in addition to what occurs in screen blank mode:

The LCD is powered off. The hard disk drive is powered off. The CPU stops.

To enter sleep (standby) mode, press Power button.

In certain circumstances, the computer goes into sleep (standby) mode automatically:

If a suspend time has been set on the timer, and the user does not do any operation with the keyboard, the hard disk, the parallel connector, or the diskette drive within that time. If the battery indicator starts blinking, indicating that the battery power is low. (Alternatively, if Hibernate when battery becomes low has been selected in the Power Management Properties window, the computer goes into hibernation mode.)

To cause the computer to return from sleep (standby) mode and resume the operation, do the following:

Turn on the power switch.

Also, in the following event, the computer automatically returns from sleep (standby) mode and resumes the operation:

The time set on the resume timer elapses.

Note: The computer does not accept any input immediately after it enters sleep (standby) mode. Wait a few seconds before taking any action to reenter operation mode.

26

IdeaPad Tablet K1 Hardware Maintenance Manual

Hibernation mode In hibernation mode, the following occurs:

The system status, RAM, VRAM, and setup data are stored on the hard disk. The system is powered off.

To cause the computer to enter hibernation mode, follow the steps below: If you are using the ACPI operating system and have defined one of the following actions as the event that causes the system to go into hibernation mode, perform that action: Pressing the power button.

Also, the computer goes into hibernation mode automatically in either of the following conditions:

If a hibernation time has been set on the timer, and if the user does not do any operation with the tablet, the hard disk drive, the parallel connector, or the diskette drive within that time. If the timer conditions are satisfied in suspend mode.

When the power is turned on, the computer returns from hibernation mode and resumes operation. The hibernation file in the boot record on the hard disk drive is read, and system status is restored from the hard disk drive.

27

Lenovo IdeaPad Tablet K1

Lenovo IdeaPad Tablet K1

This chapter presents the following product-specific service references and product-specific parts information: Specifications on page 27 FRU replacement notices on page 29 Removing and replacing an FRU on page 30 Locations on page 46 Parts list on page 48

Specifications The following table lists the specifications of the Lenovo IdeaPad Tablet K1: Table 1. Specifications

Feature Description Processor Nvidia Tegra2 T20 1.0GHzl Core Chipset SOC Graphic memory chip Intel Intergrated

Display 10.1W, LED backlight 1280x800 pixels (300 nit)

Standard memory

LPDDR2 600MHz 1GB (on board)

Solid State Drive 16G/32G, OS and data storage/on board

Optical drive N/A I/O port USB 2.0 port 1

MicroSD slot 1 Combo audio jack 1 Microphone hole 1 Speaker 2 HDMI port 1

MODEM slot N/A Audio Combo audio jack 1 Video N/A PCI Express Mini Card slot Wireless LAN MiniCard (PCIe) slot x 1(half size)

Bluetooth wireless Built-in antenna with min-USB interface, select Models

Keyboard N/A Touch screen Support Multi-touch Integrated camera 2.0MP on front/5MP on back

28

IdeaPad Tablet K1 Hardware Maintenance Manual

Table 1. Specifications (continued)

Feature Description Battery 2cell/27.4WH ACadapter 20VDC,18W Pre-installed operating system

Android3.0

29

Lenovo IdeaPad Tablet K1

FRU replacement notices

This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU.

Screw notices Loose screws can cause a reliability problem. In the Lenovo IdeaPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics:

They maintain tight connections. They do not easily come loose, even with shock or vibration. They are harder to tighten. Each one should be used only once.

Do the following when you service this machine: Keep the screw kit in your tool bag. Always use new screws. Use a torque screwdriver if you have one.

Tighten screws as follows: Plastic to plastic

Turn an additional 90 after the screw head touches the surface of the plastic part:

more than 90

(Cross-section)

Logic card to plastic Turn an additional 180 after the screw head touches the surface of the

logic card: more than 180

(Cross-section)

Torque driver If you have a torque screwdriver , refer to the Torque column for each step.

Make sure that you use the correct screws. If you have a torque screwdriver, tighten all screws firmly to the torque shown in the table. Never use a screw that you removed. Use a new one. Make sure that all screws are tightened firmly. Ensure torque screwdrivers are calibrated correctly following country specifications.

30

IdeaPad Tablet K1 Hardware Maintenance Manual

Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules: 1. Do not attempt to service any computer unless you have been trained and

certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review FRU replacement notices on page 29. 3. Begin by removing any FRUs that have to be removed before the failing

FRU. Any of such FRUs are listed at the top of the page. Remove them in the order in which they are listed.

4. Follow the correct sequence in the steps to remove the FRU, as given in the figures by the numbers in square callouts.

5. When turning a screw to replace an FRU, turn it in the direction as given by the arrow in the figure.

6. When removing the FRU, move it in the direction as given by the arrow in the figure.

7. To put the new FRU in place, reverse the removal procedures and follow any of the notes that pertain to replacement. For information about connecting and arranging internal cables, see Locations on page 46.

8. When replacing an FRU, use the correct screw as shown in the procedures.

DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any of the interconnecting cables.

Attention: After replacing an FRU, do not turn on the computer until you have made sure that all screws, springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.

Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it, establish personal grounding by touching a ground point with one hand or using an electrostatic discharge (ESD) strap (P/N 6405959) to remove potential shock reasons.

31

Lenovo IdeaPad Tablet K1

1010 Base cover

Figure 1. Removal steps of base cover Remove the base cover in the direction shown by arrows 1 2.

2

1

Note: Turn off the tablet first. Otherwise, it may cause permanent damage to the tablet.

32

IdeaPad Tablet K1 Hardware Maintenance Manual

Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following label:

The following labels need to be peeled off from the old base cover, and need to be put on the new base cover. a 3G Label b Rating Label

For some models, you also need to apply one or two FCC labels. Check the old base cover; if it has one or two FCC labels, find duplicates of them in the label kit and apply them to the new base cover.

For the location of each label, refer to the following figure:

a

b

33

Lenovo IdeaPad Tablet K1

1020 Battery pack For access, remove this FRU: 1010 Base cover on page 31

DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode.

Figure 2. Removal steps of battery pack Remove four screws 1. Disconnect the connector in the direction shown by arrow 2.

1

1

1

1 2

Step Screw (quantity) Color Torque

1 M4.5 x 3 mm, flat-head, nylon-coated (4) Silver 1.5-2.0 kg/cm

Remove the battery pack in the direction shown by arrow 3.

3

34

IdeaPad Tablet K1 Hardware Maintenance Manual

1030 Middle cover

For access, remove these FRUs in order: 1010 Base cover on page 31 1020 Battery pack on page 33

Figure 3. Removal steps of middle cover Remove four screws 1 and two screws 2. Remove the middle cover in the direction shown by arrow 3.

1

11

12

2

Step Screw (quantity) Color Torque

1 M4.5 x 5 mm, flat-head, nylon-coated (4) Silver 1.5-2.0 kg/cm

2 M3.7 x 3.5 mm, flat-head, nylon-coated (2) Silver 1.5-2.0 kg/cm

3 3

3

35

Lenovo IdeaPad Tablet K1

1040 Docking bracket

For access, remove these FRUs in order: 1010 Base cover on page 31 1020 Battery pack on page 33 1030 Middle cover on page 34

Figure 4. Removal steps of docking bracker Remove two screws 1 and then remove the docking bracker in the direction shown by arrow 2.

1 1

2

Step Screw (quantity) Color Torque

1 M4.5 x 3 mm, flat-head, nylon-coated (2) Silver 1.5-2.0 kg/cm

36

IdeaPad Tablet K1 Hardware Maintenance Manual

1050 System board

Important notices for handling the system board: When handling the system board, bear the following in mind. Be careful not to drop the system board on a bench top that has a hard surface,

such as metal, wood, or composite. Avoid rough handling of any kind. In the whole process, make sure not to drop or stack the system board. If you put a system board down, make sure to put it only on a padded surface such

as an ESD mat or conductive corrugated material.

For access, remove these FRUs in order: 1010 Base cover on page 31 1020 Battery pack on page 33 1030 Middle cover on page 34 1040 Docking bracket on page 35

Figure 5. Removal steps of system board Detach 10 connectors on system board in the direction shown by arrows 1 2 3. Remove five screws 4.

3

1 2

2

2

2

2

2 1

1

37

Lenovo IdeaPad Tablet K1

Figure 5. Removal steps of system board (continued)

4

4

4 4

4

When installing: Make sure that all the connectors are attached firmly.

Step Screw (quantity) Color Torque

4 M4.5 x 3 mm, flat-head, nylon-coated (5) Silver 1.5-2.0 kg/cm

Remove the system board in the direction shown by arrow 5.

5

38

IdeaPad Tablet K1 Hardware Maintenance Manual

1060 Switch board, SD board and HDMI board

For access, remove these FRUs in order: 1010 Base cover on page 31 1020 Battery pack on page 33 1030 Middle cover on page 34 1040 Docking bracket on page 35 1050 System board on page 36

Figure 6. Removal steps of Switch board, SD board and HDMI board Remove two screws 1, then remove the switch board in the direction shown by arrow 2.

1

1

2

Step Screw (quantity) Color Torque

1 M4.5 x 3 mm, flat-head, nylon-coated (2) Silver 1.5-2.0 kg/cm

39

Lenovo IdeaPad Tablet K1

Figure 6. Removal steps of Switch board, SD board and HDMI board (continued) Remove two screws 3, then remove the SD board in the direction shown by arrow 4.

3

4

3

Remove two screws 5, then remove the SD board bracket in the direction shown by arrow 6.

5 5

6

Step Screw (quantity) Color Torque

3 M4.5 x 3 mm, flat-head, nylon-coated (2) Silver 1.5-2.0 kg/cm

5 M4.5 x 3 mm, flat-head, nylon-coated (2) Silver 1.5-2.0 kg/cm

40

IdeaPad Tablet K1 Hardware Maintenance Manual

Figure 6. Removal steps of Switch board, SD board and HDMI board (continued)

Remove two screws 7, then remove the docking board in the direction shown by arrow 8.

7

8

7

Step Screw (quantity) Color Torque

7 M4.5 x 3 mm, flat-head, nylon-coated (2) Silver 1.5-2.0 kg/cm

41

Lenovo IdeaPad Tablet K1

1070 Speaker

For access, remove these FRUs in order: 1010 Base cover on page 31 1020 Battery pack on page 33 1030 Middle cover on page 34 1040 Docking bracket on page 35 1050 System board on page 36 1060 Switch board, SD board and HDMI board on page 38

Figure 7. Removal steps of Speaker Remove the speaker in the direction shown by arrows 1.

1

1

42

IdeaPad Tablet K1 Hardware Maintenance Manual

1080 Optical finger navigation (OFN) module

For access, remove these FRUs in order: 1010 Base cover on page 31 1020 Battery pack on page 33 1030 Middle cover on page 34 1040 Docking bracket on page 35 1050 System board on page 36 1060 Switch board, SD board and HDMI board on page 38 1070 Speaker on page 41

Figure 8. Removal steps of optical finger navigation (OFN) module Remove two screws 1 and then remove the optical finger navigation (OFN) module bracket and the module in the direction shown by arrow 2.

2

11

Step Screw (quantity) Color Torque

1 M4.5 x 3 mm, flat-head, nylon-coated (2) Silver 1.5-2.0 kg/cm

43

Lenovo IdeaPad Tablet K1

1090 Panel support bracket

For access, remove these FRUs in order: 1010 Base cover on page 31 1020 Battery pack on page 33 1030 Middle cover on page 34 1040 Docking bracket on page 35 1050 System board on page 36 1060 Switch board, SD board and HDMI board on page 38 1070 Speaker on page 41 1080 Optical finger navigation (OFN) module on page 42

Figure 9. Removal steps of panel support bracket Remove two screws 1, then remove the panel support bracket in the direction shown by arrow 2.

1

2

2

1

Step Screw (quantity) Color Torque

1 M4.5 x 5 mm, flat-head, nylon-coated (2) Silver 1.5-2.0 kg/cm

44

IdeaPad Tablet K1 Hardware Maintenance Manual

1100 Integrated camera

For access, remove these FRUs in order: 1010 Base cover on page 31 1020 Battery pack on page 33 1030 Middle cover on page 34 1040 Docking bracket on page 35 1050 System board on page 36 1060 Switch board, SD board and HDMI board on page 38 1070 Speaker on page 41 1080 Optical finger navigation (OFN) module on page 42 1090 Panel support bracket on page 43

Figure 10. Removal steps of integrated camera Note: Remove one screw 1, and then remove the integrated camera from the LCD cover in the direction shown by arrow 2.

1

2

Step Screw (quantity) Color Torque

1 M4.5 x 3 mm, flat-head, nylon-coated (1) Silver 1.5-2.0 kg/cm

When installing: Stick the integrated camera to the top center of the LCD cover and ajust the placement of it to make sure the connector is attached firmly.

45

Lenovo IdeaPad Tablet K1

1110 Antenna assembly

For access, remove these FRUs in order: 1010 Base cover on page 31 1020 Battery pack on page 33 1030 Middle cover on page 34 1040 Docking bracket on page 35 1050 System board on page 36 1060 Switch board, SD board and HDMI board on page 38 1070 Speaker on page 41 1080 Optical finger navigation (OFN) module on page 42 1090 Panel support bracket on page 43

Figure 13. Removal steps of antenna assembly Peel off the adhesive tapes securing the antenna boards, and then remove the antenna assembly in the direction shown by arrows 1.

1

When installing: Route the antenna cables along the cable guides and secure the antenna boards with adhesive tapes. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.

46

IdeaPad Tablet K1 Hardware Maintenance Manual

Locations

Front view and Right-side view 1 Integrated camera 2 Wireless module antennas (Select models only) 3 OFN button 4 Data/power jack 5 Earphone/Microphone jack 6 Micro HDMI port

1

2

3

4 5

6

47

Lenovo IdeaPad Tablet K1

Bottom and Left-side view 1 Integrated camera 2 Built-in microphone 3 Power button 4 Volume button 5 Screen rotation lock 6 Micro SD slot

3

2

4 5

6

1

48

IdeaPad Tablet K1 Hardware Maintenance Manual

Parts list This section presents the following service parts: Overall on page 49 Miscellaneous parts on page 51 AC adapters on page 52

Notes: Each FRU is available for all types or models, unless specific types or models

are specified.

49

Lenovo IdeaPad Tablet K1

Overall

a

b

c

i

d

6

7

f

8

h

12

1

2

4

5

e

9

3

10

g

11

13

50

IdeaPad Tablet K1 Hardware Maintenance Manual

Table 2. Parts listOverall

No. FRU FRU no.

1 PQXU2 LCD SUB ASSY-SILVER 18005057 1 PQXU2 LCD SUB ASSY-GRAY 18005058 2 PQXU2 WEBCAMERA CABLE FOR 2.OM-3G 31050839 2 PQXU2 WEBCAMERA CABLE FOR 2.0M-NON 3G 31050840 3 PQXU2 WEBCAMERA 2.0M 31050837 3 PQXU2 WEBCAMERA 5.0M 31050838 4 PQXU2 ANTENNA FOR 3G 31050898 4 PQXU2 ANTENNA FOR GPS 31050899 5 PQXU1 OPTICAL FINGER NAVIGATION MODULE 31047864 6 PQXU1 SPEAKER L+R0 31047873 7 PQXU2 SWITCH BOARD W/FFC 31050829 8 PQXU2 SD BOARD 31050830 9 PQXU2 HDMI BOARD 31050832 10 PQXU2 MB W/WIFI/BT/3G-32G 11013782 10 PQXU2 MB W/WIFI/BT/GPS-32G 11013783 11 PQXU2 LCD COVER FRAME SILVER FOR 3G 31050823 11 PQXU2 LCD COVER FRAME SILVER FOR NO 3G 31050824 11 PQXU2 LCD COVER FRAME GRAY FOR 3G 31050827 11 PQXU2 LCD COVER FRAME GRAY FOR NO 3G 31050828 12 Battery, U1 Slate Battery 2S1P 7.4V/27.38Wh, U1 SMP

L10M2I21 2S1P 27Wh battery 121001054

12 Battery, 3180mAh 2cell, U1 sanyo L10S2P21 2S1P 23.5Wh Polymer bty

121001185

13 PQXU2 LCD COVER LEATHER-BLACK 31050819 13 PQXU2 LCD COVER LEATHER-BROWN 31050820 13 PQXU2 LCD COVER IMR-WHITE 31050821 13 PQXU2 LCD COVER IMR-RED 31050822

51

Lenovo IdeaPad Tablet K1

Miscellaneous parts Table 3. Parts listMiscellaneous parts

FRU P/N System miscellaneous parts: (a) PQXU1 POWER BUTTON-GRAY (a) PQXU1 POWER BUTTON-SILVER (b) PQXU1 VOLUME BUTTON-GRAY (b) PQXU1 VOLUME BUTTON-SILVER (c) PQXU1 G-LOCK BUTTON-GARY (c) PQXU1 G-LOCK BUTTON-SILVER (d) PQXU2 LCD PANEL SUPPORT BRACKET (e) PQXU1 OFN MODULE BRACKET (f) PQXU2 SD BOARD BRACKET (g) PQXU1 DOCKING BRACKET (h) PQXU2 SD CARD LATCH

31047866 31047867 31047868 31047869 31047870 31047871 31050836 31047877 31050833 31047876 31050835

Cable miscellaneous parts: (i) PQXU2 TOUCH SCREEN CABLE Note: Italicized letters in parentheses are references to the exploded view in Overall on page 49 .

31050841

52

IdeaPad Tablet K1 Hardware Maintenance Manual

AC adapters Table 4. Parts list3-pin AC adapters

FRU P/N

AC Adapter(30 pin 12V 18W), AC ADAP DELTA EAPD-18SB AA 12V1.5A CH (China)

36002021

AC Adapter(30 pin 12V 18W), Delta EADP-18SB JA 12V1.5A (Argentina)

36200002

AC Adapter(30 pin 12V 18W), AC ADAP DELTA EAPD-18SB BA 12V1.5A US (US/Canada/Japan/Taiwan)

36002020

AC Adapter(30 pin 12V 18W), AC ADAP DELTA EAPD-18SB DA 12V1.5A UK(UK)

36002018

AC Adapter(30 pin 12V 18W), Delta EADP-18SB GA 12V1.5A (Korea)

36200001

AC Adapter(30 pin 12V 18W), AC ADAP DELTA EADP-18SB EA 12V1.5A AUS (Australia)

36002017

AC Adapter(30 pin 12V 18W), Delta EADP-18SB KA 12V1.5A (South Africa)

36200003

AC Adapter(30 pin 12V 18W), AC ADAP DELTA EAPD-18SB CA 12V1.5A EU (Europe/ Denmark/Switzerland / Italy/Israel)

36002019

AC Adapter(30 pin 12V 18W), Delta ADP-18AW AA 12V1.5A (China)

36200004

AC Adapter(30 pin 12V 18W), Delta ADP-18AW JA 12V1.5A (Argentina)

36200011

AC Adapter(30 pin 12V 18W), Delta ADP-18AW KA 12V1.5A (Brazil)

36200012

AC Adapter(30 pin 12V 18W), Delta ADP-18AW BA 12V1.5A (US/ Canada/Japan/Taiwan)

36200005

AC Adapter(30 pin 12V 18W), Delta ADP-18AW DA 12V1.5A (UK) 36200007

AC Adapter(30 pin 12V 18W), Delta ADP-18AW HA 12V1.5A (India)

36200017

AC Adapter(30 pin 12V 18W), Delta ADP-18AW GA 12V1.5A (Korea)

36200010

AC Adapter(30 pin 12V 18W), Delta ADP-18AW EA 12V1.5A (Australia)

36200008

AC Adapter(30 pin 12V 18W), Delta ADP-18AW MA 12V1.5A (South Africa)

36200013

AC Adapter(30 pin 12V 18W), Delta ADP-18AW CA 12V1.5A (Europe/ Denmark/Switzerland / Italy/Israel)

36200006

53

Notices

Notices

Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the users responsibility to evaluate and verify the operation of any other product, program, or service. Lenovo may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents.

LENOVO GROUP LTD. PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON- INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you. This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. The result obtained in other operating environments may vary. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk.

54

IdeaPad Tablet K1 Hardware Maintenance Manual

Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.

Trademarks The following terms are either registered trademarks or trademarks of Lenovo in the United States and/or other countries:

Lenovo

Lenovo logo

IdeaPad

OneKey

Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both.

The following are trademarks of Intel Corporation or its subsidiaries in the United States, other countries, or both:

Manualsnet FAQs

If you want to find out how the IdeaPad K1 Lenovo works, you can view and download the Lenovo IdeaPad K1 Tablet Hardware Maintenance Manual on the Manualsnet website.

Yes, we have the Hardware Maintenance Manual for Lenovo IdeaPad K1 as well as other Lenovo manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Hardware Maintenance Manual should include all the details that are needed to use a Lenovo IdeaPad K1. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Lenovo IdeaPad K1 Tablet Hardware Maintenance Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Lenovo IdeaPad K1 Tablet Hardware Maintenance Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Lenovo IdeaPad K1 Tablet Hardware Maintenance Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Lenovo IdeaPad K1 Tablet Hardware Maintenance Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Lenovo IdeaPad K1 Tablet Hardware Maintenance Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.