Contents

Lenovo V145–14AST Laptop Hardware Maintenance Manual PDF

1 of 75
1 of 75

Summary of Content for Lenovo V145–14AST Laptop Hardware Maintenance Manual PDF

Lenovo V145 Hardware Maintenance Manual

Notes: Before using this information and the product it supports, be sure to read the general information under

Notices on page 70. This manual applies to the following models: Lenovo V145-14AST / Lenovo V145-15AST.

The illustrations used in this manual are for Lenovo V145-15AST unless otherwise stated.

First Edition (August 2018) Copyright Lenovo 2018. All rights reserved. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. 2018 Lenovo

iii

Contents About this manual ....................................... iv

Safety information ........................................ 1 General safety ................................................ 2 Electrical safety .............................................. 3 Safety inspection guide .................................. 5 Handling devices that are sensitive to electrostatic discharge .................................... 6 Grounding requirements ................................. 6 Safety notices: multilingual translations.......... 7 Laser compliance statement......................... 14

Important service information ................... 16 Strategy for replacing FRUs ......................... 16

Strategy for replacing a hard disk drive ............17 Important notice for replacing a system board ...17

Important information about replacing RoHS compliant FRUs ............................................ 18

General checkout ...................................... 19 What to do first ............................................. 20 Power system checkout................................ 21

Checking the ac adapter ..................................21 Checking operational charging .........................22 Checking the battery pack ................................22

Related service information ...................... 23 Restoring the factory contents by using recovery system ........................................... 23

Restore of factory default .................................23 Passwords .................................................... 24

Power-on password ..........................................24 Hard-disk password ..........................................24 Administrator password ....................................24

Power management ..................................... 25 Putting the computer to sleep or shutting it down .................................................25 Putting your computer to sleep .........................25 Shutting down the computer .............................25

Lenovo V145 ............................................... 26 Specifications ............................................... 26 Status indicators ........................................... 28

Setting hotkey mode .........................................29 Fn key combinations/Hotkeys....................... 29 FRU replacement notices ............................. 30

Screw notices ..................................................30 Removing and replacing an FRU ................. 31

1010 Optical drive .............................................32 1020 Base cover ...............................................33 1030 Battery pack .............................................35 1040 Hard disk drive .........................................36 1050 DIMM .......................................................38

1060 PCI Express Mini Card for wireless LAN ...39 1070 ODD board ..............................................41 1080 Fan and heat sink assembly ....................42 1090 Speaker ...................................................45 1100 RTC battery ..............................................46 1110 System board ............................................ 47 1120 Upper case ...............................................49 1130 LCD unit ...................................................50 1140 EDP cable and integrated camera ...........52 1150 LCD hinges ..............................................54

Locations ...................................................... 55 Front and right-side view ..................................55 Bottom and left-side view ................................56

Parts list ........................................................ 57 Lenovo V145-14AST Overall ..............................................................58 LCD FRUs ........................................................61 Miscellaneous parts ..........................................62 ac adapters .......................................................62 Screws ..............................................................63 Lenovo V145-15AST Overall ..............................................................64 LCD FRUs ........................................................67 Miscellaneous parts ..........................................68 ac adapters .......................................................68 Screws ..............................................................69

Notices......................................................... 70 Trademarks .................................................. 71

iv

About this manual

This manual contains service and reference information for the following Lenovo products:

Lenovo V145-14AST / Lenovo V145-15AST Use this manual to troubleshoot problems. The manual is divided into the following sections: The common sections provide general information, guidelines, and safety

information required for servicing computers. The product-specific section includes service, reference, and product-specific

parts information.

Important: This manual is intended only for trained servicers who are familiar with Lenovo products. Use this manual to troubleshoot problems effectively. Before servicing a Lenovo product, make sure to read all the information under Safety information on page 1 and Important service information on page 16.

1

Safety information

Safety information

This chapter presents the following safety information that you need to get familiar with before you service a Lenovo V145-14AST / Lenovo V145-15AST computer: General safety on page 2 Electrical safety on page 3 Safety inspection guide on page 5 Handling devices that are sensitive to electrostatic discharge on page 6 Grounding requirements on page 6 Safety notices: multilingual translations on page 7 Laser compliance statement on page 14

2

Lenovo V145 Hardware Maintenance Manual

General safety Follow these rules below to ensure general safety: Observe a good housekeeping in the area where the machines are put

during and after the maintenance. When lifting any heavy object:

1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt

to lift it. 4. Lift it by standing or pushing up with your leg muscles; this action could

avoid the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you.

Do not perform any action that causes hazards to the customer, or that makes the machine unsafe.

Before you start the machine, make sure that other service representatives and the customer are not in a hazardous position.

Please remove covers and other parts in a safe place, away from all personnel, while you are servicing the machine.

Keep your toolcase away from walk areas so that other people will not trip over it.

Do not wear loose clothing that can be trapped in the moving parts of the machine. Make sure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.

Insert the ends of your necktie or scarf inside clothing or fasten it with the nonconductive clip, about 8 centimeters (3 inches) from the end.

Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing. Attention: Metal objects are good electrical conductors.

Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that may be hazardous to your eyes.

After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective.

Reinstall all covers correctly before returning the machine to the customer. Fan louvers on the machine help to prevent the overheating of internal

components. Do not obstruct fan louvers or cover them with labels or stickers.

3

Safety information

Electrical safety Observe the following rules when working on electrical equipments.

Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges. Do not use such kind of mat to protect yourself from electrical shock.

Find the room emergency power-off (EPO) switch, disconnecting switch or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.

Do not work alone under hazardous conditions or near the equipment that has hazardous voltages.

Disconnect all power before: Performing a mechanical inspection Working near power supplies Removing or installing main units

Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.

If you need to work on a machine that has exposed electrical circuits, observe the following precautions: Ensure that another person, familiar with the power-off controls, is near

you. Attention: Another person must be there to switch off the power, if

necessary. Use only one hand when working with powered-on electrical equipment;

keep the other hand in your pocket or behind your back. Attention: An electrical shock can occur only when there is a complete

circuit. By observing the above rule, you may prevent a current from passing through your body.

When using testers, set the controls correctly and use the approved probe leads and accessories for that tester.

Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages; instructions for these precautions are in the safety sections of maintenance information. Be extremely careful when you measure the high voltages. Regularly inspect and maintain your electrical hand tools for safe operational

condition. Do not use worn or broken tools and testers. Never assume that power has been disconnected from a circuit. First, check

it to make sure that it has been powered off.

4

Lenovo V145 Hardware Maintenance Manual

Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds.

Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.

Do not service the following parts with the power on when they are removed from their normal operating places in a machine: Power supply units Pumps Blowers and fans Motor generators and similar units. (This practice ensures correct grounding of the units.)

If an electrical accident occurs: Caution: do not become a victim yourself. Switch off the power. Send the victim to get medical aid.

5

Safety information

Safety inspection guide The purpose of this inspection guide is to assist you in identifying potential unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards according to the attachment of non-Lenovo features or options not covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present: Electrical hazards, especially primary power (primary voltage on the frame

can cause serious or fatal electrical shock) Explosive hazards, such as a damaged CRT face or a bulging capacitor Mechanical hazards, such as loose or missing hardware

To determine whether there are any potential unsafe conditions, use the following checklist at the beginning of every service task. Begin the checks with the power off, and the power cord disconnected.

Checklist: 1. Check exterior covers for damage (loose, broken, or sharp edges). 2. Turn off the computer. Disconnect the power cord. 3. Check the power cord for:

a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground.

b. The power cord should be the type specified in the parts list. c. Insulation must not be frayed or worn.

4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the

safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal

filings, contamination, water or other liquids, or signs of fire or smoke damage.

8. Check for worn, frayed, or pinched cables. 9. Check that the power-supply cover fasteners (screws or rivets) have not

been removed or tampered with.

6

Lenovo V145 Hardware Maintenance Manual

Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.

Notes: 1. Use product-specific ESD procedures when they exceed the requirements noted

here. 2. Make sure that the ESD protective devices you use have been certified

(ISO 9000) as fully effective.

When handling ESD-sensitive parts: Keep the parts in protective packages until they are inserted into the product. Avoid contact with other people. Wear a grounded wrist strap against your skin to eliminate static on your

body. Prevent the part from touching your clothing. Most clothing is insulative and

retains a charge even when you are wearing a wrist strap. Use the black side of a grounded work mat to provide a static-free work

surface. The mat is especially useful when handling ESD-sensitive devices. Select a grounding system, such as those listed below, to provide protection

that meets the specific service requirement.

Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.

Attach the ESD ground clip to any frame ground, ground braid, or green- wire ground.

When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector- outside shells on these systems.

Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.

7

Safety information

Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish.

Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. Avant de remettre lordinateur sous tension aprs remplacement dune unit en clientle, vrifiez que tous les ressorts, vis et autres pices sont bien en place et bien fixes. Pour ce faire, secouez lunit et assurez-vous quaucun bruit suspect ne se produit. Des pices mtalliques ou des copeaux de mtal pourraient causer un court-circuit. Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, mu sichergestellt werden, da keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehuse vergessen wurden. Der Computer mu geschttelt und auf Klappergerusche geprft werden. Metallteile oder-splitter knnen Kurzschlsse erzeugen.

Prima di accendere lelaboratore dopo che stata effettuata la sostituzione di una FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e non siano sparse allinterno dellelaboratore. Verificare ci scuotendo lelaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi.

Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y dems piezas pequeas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Comprubelo agitando el sistema y escuchando los posibles ruidos que provocaran. Las piezas metlicas pueden causar cortocircuitos elctricos.

8

Lenovo V145 Hardware Maintenance Manual

Safety notice 2

DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short- circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium. Ne les dmontez pas, ne les rechargez pas, ne les exposez ni au feu ni leau. Ne les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous la rglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle de lhorloge temps rel, veillez nutiliser que les modles cits dans la liste de pices dtaches adquate. Une batterie ou une pile inapproprie risque de prendre feu ou dexploser. Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.

Alcune batterie di riserva contengono una piccola quantit di nichel e cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nellacqua n cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria dellRTC (real time clock) o la batteria di supporto, utilizzare soltanto i tipi inseriti nellappropriato Catalogo parti. Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa.

Algunas bateras de reserva contienen una pequea cantidad de nquel y cadmio. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deschelas tal como dispone la normativa local. Utilice slo bateras que se encuentren en la lista de piezas. La utilizacin de una batera no apropiada puede provocar la ignicin o explosin de la misma.

9

Safety information

Safety notice 3

DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la dmontez pas, ne lexposez ni au feu ni leau. Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous la rglementation en vigueur. Lorsque vous remplacez la batterie, veillez nutiliser que les modles cits dans la liste de pices dtaches adquate. En effet, une batterie inapproprie risque de prendre feu ou dexploser. Akkus enthalten geringe Mengen von Nickel. Sie drfen nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.

La batteria contiene piccole quantit di nichel. Non smontarla, gettarla nel fuoco o nellacqua n cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria, utilizzare soltanto i tipi inseriti nellappropriato Catalogo parti. Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa.

Las bateras contienen pequeas cantidades de nquel. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deschelas tal como dispone la normativa local. Utilice slo bateras que se encuentren en la lista de piezas al sustituir la batera. La utilizacin de una batera no apropiada puede provocar la ignicin o explosin de la misma.

10

Lenovo V145 Hardware Maintenance Manual

Safety notice 4

DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100C (212F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium. Elle prsente des risques dincendie, dexplosion ou de brlures graves. Ne la rechargez pas, ne retirez pas son connecteur polaris et ne la dmontez pas. Ne lexposez pas une temperature suprieure 100C, ne la faites pas brler et nen exposez pas le contenu leau. Mettez la pile au rebut conformment la rglementation en vigueur. Une pile inapproprie risque de prendre feu ou dexploser. Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entznden, explodieren oder schwere Verbrennungen hervorrufen. Batterien dieses Typs drfen nicht aufgeladen, zerlegt, ber 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.

La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa.

La batera de repuesto es una batera de litio y puede provocar incendios, explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte, ni caliente por encima de los 100C (212F), ni la incinere ni exponga el contenido de sus celdas al agua. Deschela tal como dispone la normativa local.

11

Safety information

Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau daffichage cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un mdecin si des symptmes persistent aprs le lavage. Die Leuchtstoffrhre im LCD-Bildschirm enthlt Quecksilber. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgem behandelt wird oder der Computer auf den Boden fllt. Wenn der Bildschirm beschdigt ist und die darin befindliche Flssigkeit in Kontakt mit Haut und Augen gert, sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgesplt und bei Beschwerden anschlieend ein Arzt aufgesucht werden.

Nel caso che caso lLCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero permanere.

Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos, lave inmediatamente las reas afectadas con agua durante 15 minutos como mnimo. Obtenga atencin medica si se presenta algn sntoma del fluido despues de lavarse.

12

Lenovo V145 Hardware Maintenance Manual

Safety notice 6

DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin dviter tout risque de choc lectrique, ne retirez pas le cache en plastique protgeant la partie infrieure de la carte dalimentation. Aus Sicherheitsgrnden die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.

Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore.

Para evitar descargas, no quite la cubierta de plstico que rodea la parte baja de la tarjeta invertida.

Safety notice 7

DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. Bien que le voltage des batteries principales soit peu lev, le court-circuit ou la mise la masse dune batterie peut produire suffisamment de courant pour brler des matriaux combustibles ou causer des brlures corporelles graves. Obwohl Hauptbatterien eine niedrige Spannung haben, knnen sie doch bei Kurzschlu oder Erdung genug Strom abgeben, um brennbare Materialien zu entznden oder Verletzungen bei Personen hervorzurufen.

Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto circuito o a massa pu fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione.

Aunque las bateras principales tienen un voltaje bajo, una batera cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.

13

Safety information

Safety notice 8

DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unit remplaable en clientle, mettez le systme hors tension, dbranchez tous les cordons dalimentation des socles de prise de courant, retirez la batterie et dconnectez tous les cordons dinterface. Die Stromzufuhr mu abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt wird.

Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di interconnessione.

Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas de corriente elctrica, quite la batera y, a continuacin, desconecte cualquier cable de conexin entre dispositivos.

14

Lenovo V145 Hardware Maintenance Manual

Laser compliance statement Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.

If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note the following:

CAUTION Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure. O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposio radiao.

Pour viter tout risque dexposition au rayon laser, respectez les consignes de rglage et dutilisation des commandes, ainsi que les procdures dcrites. Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann gefhrliche Laserstrahlung auftreten.

Lutilizzo di controlli, regolazioni o lesecuzione di procedure diverse da quelle specificate possono provocare lesposizione a.

El uso de controles o ajustes o la ejecucin de procedimientos distintos de los aqu especificados puede provocar la exposicin a radiaciones peligrosas.

Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage device could result in exposure to hazardous laser radiation. There are no serviceable parts inside those drives. Do not open.

15

Safety information

A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following:

DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiao por raio laser ao abrir. No olhe fixo no feixe de luz, no olhe diretamente por meio de instrumentos ticos e evite exposio direta com o feixe de luz.

Rayonnement laser si carter ouvert. vitez de fixer le faisceau, de le regarder directement avec des instruments optiques, ou de vous exposer au rayon. Laserstrahlung bei geffnetem Gert. Nicht direkt oder ber optische Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden. Kinyitskor lzersugr ! Ne nzzen bele se szabad szemmel, se optikai eszkzkkel. Kerlje a sugrnyalbbal val rintkezst! Aprendo lunit vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici e evitare lesposizione diretta al fascio.

Radiacin lser al abrir. No mire fijamente ni examine con instrumental ptico el haz de luz. Evite la exposicin directa al haz.

16

Lenovo V145 Hardware Maintenance Manual

Important service information

This chapter presents the following important service information: Strategy for replacing FRUs on page 16

Strategy for replacing a hard disk drive on page 17 Important notice for replacing a system board on page 17

Important information about replacing RoHS compliant FRUs on page 18

Important: BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site: http://support.lenovo.com.

Strategy for replacing FRUs

Before replacing parts: Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual. After a system board is replaced, ensure that the latest BIOS is loaded to the system board before completing the service action. To download software fixes, drivers, and BIOS, follow the steps below: 1. Go to http://support.lenovo.com. 2. Enter the serial number or select a product or use Lenovo smart

downloading. 3. Select the BIOS/Driver/Applications and download. 4. Follow the directions on the screen and install the necessary software.

17

Important service information

Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: If you are instructed to replace an FRU, but the replacement does not solve

the problem, reinstall the original FRU before you continue. Some computers have both a processor board and a system board. If you

are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one.

If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs one by one to see if the symptoms change. Replace only the FRU that changed the symptoms.

Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect.

Strategy for replacing a hard disk drive Always try to run a low-level format before replacing a hard disk drive. This will cause all customer data on the hard disk to be lost. Make sure that the customer has a current backup of the data before performing this action. Attention: The drive startup sequence in the computer you are servicing may have been changed. Be extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect drive, data or programs can be overwritten.

Important notice for replacing a system board Some components mounted on a system board are very sensitive. Improper handling can cause damage to those components, and may cause a system malfunction. Attention: When handling a system board: Do not drop the system board or apply any excessive force to it. Avoid rough handling of any kind. Avoid bending the system board and hard pushing to prevent cracking at

each BGA (Ball Grid Array) chipset.

18

Lenovo V145 Hardware Maintenance Manual

Important information about replacing RoHS compliant FRUs

RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts. If the original FRU parts are non-compliant, replacement parts can also be non-compliant. In all cases if the original FRU parts are RoHS compliant, the replacement part must also be RoHS compliant.

Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified with unique FRU part numbers.

Lenovo plans to transit to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovos requirements and schedule in the EU. Products sold in 2005 and 2006 will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant FRUs.

RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS implementation date, failed RoHS compliant parts must always be replaced with RoHS compliant ones, so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs may be used.

Products marketed before June 2006 Products marketed after June 2006 Current or original part

Replacement FRU Current or original part

Replacement FRU

Non-RoHS Can be Non-RoHS

Must be RoHS Must be RoHS Non-RoHS Can be RoHS

Non-RoHS Can sub to RoHS

RoHS Must be RoHS

Note: A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of the order.

19

General checkout

General checkout

This chapter presents the following information: What to do first on page 20 Power system checkout on page 21

Before you go to the checkout, make sure to read the following important notes:

Important notes: Onlycertifiedtrainedpersonnelcanservicethecomputer. BeforereplacinganyFRU,readtheentirepageonremovingandreplacing FRUs.

CarefullyremovescrewsforreusewhenreplacingFRUs. Beextremelycarefulduringsuchwriteoperationsascopying,saving,or formatting. Drives in the computer that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be overwritten.

ReplaceanFRUonlywithanotherFRUof thecorrectmodel. When you replace an FRU, make sure that the machine model and the FRU part number are correct by referring to the FRU parts list.

AnFRUshouldnotbereplacedjustbecauseofasingle,unreproduciblefailure. Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. Consider replacing an FRU only when a problem recurs. If you suspect that an FRU is defective, clear the error logs and run the test again. If the error does not recur, do not replace the FRU.

BecarefulnottoreplaceanondefectiveFRU.

20

Lenovo V145 Hardware Maintenance Manual

What to do first When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Procedure index and page number in which the failing FRU was detected 6. Failing FRU name and part number 7. Machine type, model number, and serial number 8. Customers name and address

Note for warranty: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer. The following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use. Before checking problems with the computer, determine whether the damage is covered under the warranty by referring to the following list:

The following are not covered under warranty: LCD panel cracked from the application of excessive force or from being

dropped Scratched (cosmetic) parts Distortion, deformation, or discoloration of the cosmetic parts Plastic parts, latches, pins, or connectors that have been cracked or broken

by excessive force Damage caused by liquid spilled into the system Damage caused by the improper insertion of a PC Card or the installation of

an incompatible card Improper disk insertion or use of an optical drive Diskette drive damage caused by pressure on the diskette drive cover,

foreign material in the drive, or the insertion of a diskette with multiple labels Damaged or bent diskette eject button Fuses blown by attachment of a nonsupported device Forgotten computer password (making the computer unusable) Sticky keys caused by spilling a liquid onto the keyboard Use of an incorrect ac adapter on laptop products

The following symptoms might indicate damage caused by nonwarranted activities: Missing parts might be a symptom of unauthorized service or modification. If the spindle of a hard disk drive becomes noisy, it may have been subjected

to excessive force, or dropped.

21

General checkout

Power system checkout

To verify a symptom, follow the steps below: 1. Turn off the computer. 2. Remove the battery pack. 3. Connect the ac adapter. 4. Make sure that power is supplied when you turn on the computer. 5. Turn off the computer. 6. Disconnect the ac adapter and install the charged battery pack. 7. Make sure that the battery pack supplies power when you turn on the

computer.

If you suspect a power problem, see the appropriate one of the following power supply checkouts: Checking the ac adapter on page 21 Checking operational charging on page 22 Checking the battery pack on page 22

Checking the ac adapter You are here because the computer fails only when the ac adapter is used. If the power-on indicator does not turn on, check the power cord of the ac

adapter for correct continuity and installation. If the computer does not charge during operation, go to "Checking

operational charging". To check the ac adapter, follow the steps below: 1. Unplug the ac adapter cable from the computer. 2. Measure the output voltage at the plug of the ac adapter cable. See the

following figure:

1

2

Voltage (V dc)

+20

Pin

1

2

Note: Output voltage for the ac adapter pin No. 2 may differ from the one you are servicing. 3. If the voltage is not correct, replace the ac adapter. 4. If the voltage is acceptable, do the following: Replace the system board. If the problem persists, go to Lenovo V145 on page 26. Note: Noise from the ac adapter does not always indicate a defect.

22

Lenovo V145 Hardware Maintenance Manual

Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not light on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack.

If the charge indicator still does not light on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section.

Checking the battery pack Battery charging does not start until the Power Meter shows that less than 95% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life.

To check your battery, move your cursor to the Power Meter icon in the icon tray of the Windows taskbar and wait for a moment (but do not click it), and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon.

Note: If the battery pack becomes hot, it may not be able to be charged. Remove it from the computer and leave it at room temperature for a while. After it cools down, reinstall and recharge it.

23

Related service information

Related service information

This chapter presents the following information: Restoring the factory contents by using recovery system on page 23 Passwords on page 24 Power management on page 25

Restoring the factory contents by using recovery system

Restore of factory default The Lenovo V145-14AST / Lenovo V145-15AST computers come with pre- installed recovery system. In order to save application files and the initial backed up files of the system, the hard disk in a Lenovo computer includes a hidden partition when it is shipped. If you need to restore the system to the point of your first boot up, just enter the recovery system. For details of the Recovery system, see the User Guide for Recovery system.

Note: This will delete all the new data on the system partition (C drive), which is not recoverable. Make sure to back up your critical data before you perform this action.

24

Lenovo V145 Hardware Maintenance Manual

Passwords

As many as three passwords may be needed for any Lenovo computer: the power-on password (POP), the hard disk password (HDP), and the administrator password. If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.

Power-on password A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted.

Hard-disk password There are two hard-disk passwords (HDPs): + User HDP - for the user + Master HDP - for the system administrator, who can use it to get access to the hard disk drive even if the user has changed the user HDP Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenovo authorized service technicians provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.

Administrator password Administrator password controls the access of the whole setup utility. Only Administrator password was set then User password can be set. If Administrator password was cleared, the User password was cleared too.

25

Related service information

Power management

Note: Power management modes are not supported for APM operating system.

Putting the computer to sleep or shutting it down When you have finished working with your computer, you can put it to sleep or shut it down.

Putting your computer to sleep If you will be away from your computer for only a short time, put the computer to sleep. When the computer is in sleep mode, you can quickly wake it to resume use, bypassing the startup process. To put the computer to sleep, do one of the following: Close the display lid. Press the Power button. Open the start menu, and then select Power Sleep.

Attention: Wait until the power indicator light starts blinking (indicating that the computer is in sleep mode) before you move your computer. Moving your computer while the hard disk is spinning can damage the hard disk, causing loss of data.

To wake the computer, do one of the following: Press any key on the keyboard. Press the Power button.

Shutting down the computer If you are not going to use your computer for a long time, shut it down. To shut down the computer, do one of the following:

Open the start menu, and then select Power Shut down. Right-click the Start button in the lower-left corner and select Shut down or

sign out Shut down.

26

Lenovo V145 Hardware Maintenance Manual

Lenovo V145

This chapter presents the following product-specific service references and product-specific parts information: Specifications on page 26 Status indicators on page 28 Fn key combinations/Hotkeys on page 29 FRU replacement notices on page 30 Removing and replacing an FRU on page 31 Locations on page 55 Parts list on page 57

Specifications The following table lists the specifications of the Lenovo V145-14AST / Lenovo V145-15AST: Table 1. Specifications

Feature Description Processor View the system properties of your computer.

You can do this as follows: Open the Control Panel, and then select System and Security System.

Graphic memory chip

Integrated graphics: Depends on CPU Discreted graphics: AMD LV2-R17M-M1-70 (Lenovo V145-14AST /

Lenovo V145-15AST) Display 14.0" 16:9, 1,366 X 768 pixels HD / 1,920 x 1,080 pixels FHD

(Lenovo V145-14AST) 15.6" 16:9, 1,366 X 768 pixels HD / 1,920 x 1,080 pixels FHD

(Lenovo V145-15AST) Standard memory

DDR4-2133 MHz, SODIMM 1 (max 8 GB) (Lenovo V145-14AST / Lenovo V145-15AST)

Storage devices HDD: 2.5-inch, 7.0 mm SATA II/SATA III SSD: 128 GB, SATA III

(Lenovo V145-14AST / Lenovo V145-15AST)

27

Lenovo V145

Table 1. Specifications (continued)

Feature Description Optical drive 9.0 mm, Rambo I/O port USB 3.0 2

Combo audio connector 1 HDMI connector 1 RJ-45 connector 1 4 in 1 slot 1 (SD/SDHC/SDXC/MMC)

Audio 3.5 mm Combo audio connector 1.5 W speaker 2

Bluetooth wireless Combined in combo card

Keyboard 6 rows Lenovo Keyboard Integrated camera HD / 0.3 M

Battery Polymer battery pack 2 cells, 30 Wh (Lenovo V145-14AST / Lenovo V145-15AST)

ac adapter 20 V dc, UMA 45 W, DIS 65 W Pre-installed operating system

Win 10 64bits Free-DOS

28

Lenovo V145 Hardware Maintenance Manual

Status indicators The system status indicators below show the computer status:

2

1

Table 2. Status indicators

Symbol Indicator Indicator status

Charge status Meaning

Power

On (solid white)

--- The computer is powered on.

Blinking --- The computer is in sleep mode. Off --- The computer is powered off.

Battery

On (solid white)

Charging The battery has more than 80% charge, charging will continue until the battery is fully charged.

On (solid amber)

Discharging The battery has between 5% and 20% charge.

Blinking slowly (white)

Charging

The battery has between 20% and 80% charge. When the battery reaches 80% charge, the light will stop blinking. However, charging will continue until the battery is fully charged.

Blinking slowly (amber)

Charging The battery is being charged. When battery charge reaches 20%, the blinking color changes to white.

Blinking quickly (amber)

Discharging The battery has between 1% and 5% charge.

Off Discharging The computer is in sleep mode or turned off; the battery has more than 20% charge.

29

Lenovo V145

Fn key combinations/Hotkeys

You can access certain system settings quickly by pressing the appropriate hotkeys.

Table 3. Hotkeys

: Mutes/unmutes the sound. : Enables/disables Airplane mode.

: Decreases the volume level. : Enables/disables the integrated camera.

: Increases the volume level. : Locks the screen.

: Enables/disables the microphone. :

Toggles the display between the computer and an external device.

: Refreshes the desktop or the currently active window. : Decreases the display

brightness.

: Enables/disables the touchpad. : Increases the display

brightness.

Setting hotkey mode By default, the hotkey functions are accessible by pressing the appropriate hotkey. However, you can disable the hotkey mode in the BIOS setup utility. To disable the hotkey mode: 1. Shut down the computer. 2. Press the Novo button and then select BIOS Setup. 3. In the BIOS setup utility, open the Configuration menu, and change the

setting of HotKey Mode from Enabled to Disabled. 4. Open the Exit menu, and select Exit Saving Changes. Note: When hotkey mode is disabled, press the Fn key and the appropriate hotkey to access the corresponding hotkey function.

30

Lenovo V145 Hardware Maintenance Manual

FRU replacement notices This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU.

Screw notices Loose screws can cause a reliability problem. In the Lenovo computer, this problem is addressed with special nylon-coated screws that have the following characteristics: They maintain tight connections. They do not easily come loose, even with shock or vibration. They are harder to tighten.

Do the following when you service this machine: Keep the screw kit in your tool bag. Carefully remove screws for reuse when replacing FRUs. Use a torque screwdriver if you have one.

Tighten screws as follows: Plastic to plastic Turn an additional 90 after the screw head touches the surface of the

plastic part: more than 90

(Cross-section)

Logic card to plastic Turn an additional 180 after the screw head touches the surface of the

logic card: more than 180

(Cross-section)

Torque driver If you have a torque screwdriver , refer to the Torque column for each step. Make sure that you use the correct screws. If you have a torque screwdriver,

tighten all screws firmly to the torque shown in the table. Carefully remove screws for reuse when replacing FRUs. Make sure that all screws are tightened firmly.

Ensure torque screwdrivers are calibrated correctly following country specifications.

31

Lenovo V145

Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules: 1. Do not attempt to service any computer unless you have been trained and

certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review FRU replacement notices on page 30. 3. Begin by removing any FRUs that have to be removed before the failing

FRU. Any of such FRUs are listed at the top of the page. Remove them in the order in which they are listed.

4. Follow the correct sequence in the steps to remove the FRU, as given in the figures by the numbers in square callouts.

5. When turning a screw to replace an FRU, turn it in the direction as given by the arrow in the figure.

6. When removing the FRU, move it in the direction as given by the arrow in the figure.

7. To put the new FRU in place, reverse the removal procedures and follow any of the notes that pertain to replacement. For information about connecting and arranging internal cables, see Locations on page 55.

8. When replacing an FRU, use the correct screw as shown in the procedures.

DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any of the interconnecting cables.

Attention: After replacing an FRU, do not turn on the computer until you have made sure that all screws, springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.

Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it, establish personal grounding by touching a ground point with one hand or using an electrostatic discharge (ESD) strap (P/N 6405959) to remove potential shock reasons.

Notes: This manual applies to the following models:

Lenovo V145-14AST / Lenovo V145-15AST. The illustrations used in this manual are for Lenovo V145-15AST unless otherwise

stated.

32

Lenovo V145 Hardware Maintenance Manual

1010 Optical drive

Figure 1. Removal steps of optical drive

Remove the screw , then gently pull the optical drive out in the direction shown by arrow .

12

Step Screw (quantity) Color Torque M2.5 7 mm, Phillips head, nylok-coated (1) LOW TO UPPER

Black 1.850.15 kgf*cm

Remove the screw , then carefully remove the optical drive bracket and bezel in the directions shown by arrows and .

3

4

5

Step Screw (quantity) Color Torque M2 3.5 mm, Phillips head, nylok-coated (1) ODD BRK TO ODD

Silver 1.850.15 kgf*cm

33

Lenovo V145

1020 Base cover

For access, remove these FRUs in order: 1010 Optical drive on page 32

Figure 2. Removal steps of base cover

Remove the screws from the bottom.

1

1

1 1

1

1

1

1

1

1

1

1

Step Screw (quantity) Color Torque M2.5 7 mm, Phillips head, nylok-coated (12) LOW TO UPPER

Black 1.850.15 kgf*cm

Remove the base cover .

2

34

Lenovo V145 Hardware Maintenance Manual

Note: Applying labels to the base cover If you see the following labels on base cover, it needs to be peeled off from the old base cover, and put on the new base cover.

a Rating label b GML label c Brazil label d TW vision warning label e Adapter label f KR KRR label g Argentina label h Israel/US/CA/TW label i India BIS label j Indonesia rating label k South Africa label l Malaysia/Indonesia label

For some models, you also need to apply one or two FCC labels. Check the old base cover; if it has one or two FCC labels, find duplicates of them in the label kit and apply them to the new base cover. For the location of each label, refer to the following figures:

Lenovo V145-15AST

a

b

l

c c

g

e

j

k

d

i

f

h

Lenovo V145-14AST

a

b

l

c c

g

e

j

k

d

i

f

h

35

Lenovo V145

1030 Battery pack

For access, remove this FRU: 1010 Optical drive on page 32 1020 Base cover on page 33

DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode.

Figure 3. Removal steps of battery pack

Unplug the battery pack connector in the direction shown by arrow , then remove the screws . Remove the battery pack in the direction shown by arrow .

Lenovo V145-15AST

3

1

2

2

2

Lenovo V145-14AST

3

1

2

2

Step Screw (quantity) Color Torque M2 6 mm, Phillips head, nylok-coated (3) (Lenovo V145-15AST) BATTERY MODULE TO UPPER

Silver 1.850.15 kgf*cm

M2 6 mm, Phillips head, nylok-coated (2) (Lenovo V145-14AST) BATTERY MODULE TO UPPER

Silver 1.850.15 kgf*cm

When installing: Make sure that the battery connector is attached firmly.

36

Lenovo V145 Hardware Maintenance Manual

1040 Hard disk drive

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35

Attention: Donotdroptheharddiskdriveorapplyanyphysicalshocktoit. The hard

disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data.

Before removing the drive, suggest the customer to backup all the information on it if possible.

Never remove the drive while the system is operating or is in suspend mode.

Figure 4. Removal steps of hard disk drive

Detach the connector in the direction shown by arrows and . Remove the screws .

3 3

3

3 2

1

Step Screw (quantity) Color Torque M2 6 mm, Phillips head, nylok-coated (4) HDD BRK TO UPPER & HDD/B TO UPPER

Silver 1.850.15 kgf*cm

37

Lenovo V145

Figure 4. Removal steps of hard disk drive (continued)

Remove the hard disk drive in the direction shown by arrow .

4

Remove the hard disk drive board in the direction shown by arrow . Remove the screws , and then take out the metal frame.

5

6

6

6

6

Step Screw (quantity) Color Torque M3 3 mm, Phillips head, nylok-coated (4) HDD BRK TO HDD

Silver 30.3 kgf*cm

38

Lenovo V145 Hardware Maintenance Manual

1050 DIMM

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35

Figure 5. Removal steps of DIMM

Release the two latches on both edges of the socket at the same time in the directions shown by arrows , and then unplug the DIMM in the direction shown by arrow .

1 12

When installing: Insert the notched end of the DIMM into the socket. Push the DIMM firmly, and pivot it until it snaps into place. Make sure that it is firmly fixed in the slot and is difficult to move. Note: When replacing the memory is completed, you need to restart the computer after the first reboot.

39

Lenovo V145

1060 PCI Express Mini Card for wireless LAN

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35

Important: The preinstalled WLAN module may only be replaced with a Lenovo approved module in order to comply with FCC and IC regulations. Refer to Table 4. Parts list-Overall (Lenovo V145-14AST) on page 59 or Table 9. Parts list-Overall (Lenovo V145-15AST) on page 65 for Lenovo part numbers for the approved modules.

Figure 6. Removal steps of PCI Express Mini Card for wireless LAN

Peel off the tape

1

Disconnect the two wireless LAN cables (black, gray) . Remove the screw .

23

In step , unplug the antenna RF connector (P/N: 08K7159) by using the removal tool, or pick up the connectors with your fingers and gently unplug them in the direction shown by the arrows.

Notes: The wireless LAN card has 2 cables in step . The wireless LAN card in some models might have 3 cables in step .

Step Screw (quantity) Color Torque M2 3.5 mm, Phillips head, nylok-coated (1) WLAN CARD TO UPPER

Silver 1.850.15 kgf*cm

40

Lenovo V145 Hardware Maintenance Manual

Figure 6. Removal steps of PCI Express Mini Card for wireless LAN (continued)

Remove the card in the direction shown by arrow .

4

When installing: In models with a wireless LAN card that has two antenna connectors, plug

the black cable (1st) (MAIN) into the connector labeled MAIN, and the grey cable (2nd) (AUX) into the connector labeled AUX on the card.

In models with a wireless LAN card that has three antenna connectors, plug the black cable (1st) (MAIN) into the connector labeled 1, the grey cable (3rd) into the connector labeled 3, and the white cable (2nd) (AUX) into the connector labeled 2 on the card.

41

Lenovo V145

1070 ODD board

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35

Figure 7. Removal steps of ODD board

Detach the ODD board connector in the directions shown by arrows and . Remove the screw .

2

1

3

Remove the ODD board .

4

Step Screw (quantity) Color Torque M2 X 3.5 mm, Phillips head, nylok-coated (1) ODD BOARD TO UPPER

Silver 1.850.15 kgf*cm

42

Lenovo V145 Hardware Maintenance Manual

1080 Fan and heat sink assembly

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35

Figure 8. Removal steps of fan and heat sink assembly

Unplug the fan connector in the direction shown by arrow . Remove the screw . Release the antenna from the cable guides.

2

1

Step Screw (quantity) Color Torque M2 6 mm, Phillips head, nylok-coated (1) FAN TO UPPER

Silver 1.850.15 kgf*cm

Lift the fan in the direction shown by arrow .

3

43

Lenovo V145

Figure 8. Removal steps of fan and heat sink assembly (continued)

Remove the screws .

Lenovo V145-15AST

4 4

4 4

4

Lenovo V145-14AST

4 4 4

Step Screw (quantity) Color Torque M2 3.5 mm, Phillips head, nylok-coated (5) (Lenovo V145-15AST) THERMAL MODULE TO CPU & THERMAL MODULE TO GPU (DIS)

Silver 1.850.15 kgf*cm

M2 3.5 mm, Phillips head, nylok-coated (3) (Lenovo V145-14AST) THERMAL TO M/B (CPU)

Silver 1.850.15 kgf*cm

44

Lenovo V145 Hardware Maintenance Manual

Figure 8. Removal steps of fan and heat sink assembly (continued)

Lift the fan in the direction shown by arrow .

5

Attention: Do not handle the heat sink assembly roughly. Improper handling can cause distortion or deformation and imperfect contact with components.

Lenovo V145-15AST

a

b

Lenovo V145-14AST

b

When installing: Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, to the a and b parts shown in the figure above. Either too much or too little grease application can cause a thermal problem due to imperfect contact with a component.

45

Lenovo V145

1090 Speaker

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35

Figure 9. Removal step of speaker

Unplug the speaker connector in the direction shown by arrow . Remove the two speakers . Release the antenna from the cable guides.

1

2

2

When installing: Make sure that the connector is attached firmly.

46

Lenovo V145 Hardware Maintenance Manual

1100 RTC battery

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35

Figure 10. Removal steps of RTC battery

Unplug the RTC battery connector in the direction shown by arrow . Remove the RTC battery .

1

2

When installing: Make sure that the connector is attached firmly.

47

Lenovo V145

1110 System board

Important notices for handling the system board: When handling the system board, bear the following in mind. Be careful not to drop the system board on a bench top that has a hard surface,

such as metal, wood, or composite. Avoid rough handling of any kind. In the whole process, make sure not to drop or stack the system board. If you put a system board down, make sure to put it only on a padded surface such

as an ESD mat or conductive corrugated material.

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35 1040 Hard disk drive on page 36 1070 ODD board on page 41 1080 Fan and heat sink assembly on page 42 1090 Speaker on page 45 1100 RTC battery on page 46

Figure 11. Removal steps of system board

Detach the three connectors (EDP cable connector, KB FFC connector, touchpad connector) in the directions shown by arrows , and . Remove the screws .

2

1

2

1

4 4 4

3

Step Screw (quantity) Color Torque M2 3.5 mm, Phillips head, nylok-coated (3) MB TO UPPER & DC-IN TO UPPER

Silver 1.850.15 kgf*cm

48

Lenovo V145 Hardware Maintenance Manual

Figure 11. Removal steps of system board (continued)

Remove the system board in the direction shown by arrow .

5

When installing: Make sure that the connectors are attached firmly.

49

Lenovo V145

1120 Upper case

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35 1040 Hard disk drive on page 36 1070 ODD board on page 41 1080 Fan and heat sink assembly on page 42 1090 Speaker on page 45 1100 RTC battery on page 46 1110 System board on page 47

Figure 12. Removal steps of upper case

Remove the screws .

1 1

1 1

Step Screw (quantity) Color Torque M2.5 4.5 mm, Phillips head, nylok-coated (4) HINGE BRK TO UPPER

Silver 30.3 kgf*cm

Open the hinge in the direction shown by arrows . Release the antenna from the cable guides. Remove the upper case in the direction shown by arrow .

2

2

3

3

50

Lenovo V145 Hardware Maintenance Manual

1130 LCD unit

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35 1040 Hard disk drive on page 36 1070 ODD board on page 41 1080 Fan and heat sink assembly on page 42 1090 Speaker on page 45 1100 RTC battery on page 46 1110 System board on page 47 1120 Upper case on page 49

Figure 13. Removal steps of LCD unit

Remove the LCD front bezel in the direction shown by arrows .

1

1

1

1

Pull the hinge cover in the direction shown by arrows . Remove the hinge cover in the direction shown by arrow .

2

2

3

51

Lenovo V145

Figure 13. Removal steps of LCD unit (continued)

Remove the screws .

4

4

4

4

Step Screw (quantity) Color Torque M2 x 2.5 mm, Phillips head, nylok-coated (4) LCD PANEL TO LCD COVER

Black 1.850.15 kgf*cm

Lift the LCD panel slightly . Unplug the EDP connector . Then remove the LCD panel.

5

6

When installing: Make sure that the metal connector is attached firmly.

52

Lenovo V145 Hardware Maintenance Manual

1140 EDP cable and integrated camera

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35 1040 Hard disk drive on page 36 1070 ODD board on page 41 1080 Fan and heat sink assembly on page 42 1090 Speaker on page 45 1100 RTC battery on page 46 1110 System board on page 47 1120 Upper case on page 49 1130 LCD unit on page 50

Figure 14. Removal steps of EDP cable and integrated camera

Note: The integrated camera is stuck on the top center of the LCD cover.

Unplug the connector , peel of the tape .

2

1

Remove the EDP cable in the direction shown by arrow .

3

53

Lenovo V145

Figure 14. Removal steps of EDP cable and integrated camera (continued)

Remove the camera board in the direction shown by arrow .

4

When installing: Stick the integrated camera to the top center of the LCD cover and adjust the placement of it to make sure the connector is attached firmly.

54

Lenovo V145 Hardware Maintenance Manual

1150 LCD hinges

For access, remove these FRUs in order: 1010 Optical drive on page 32 1020 Base cover on page 33 1030 Battery pack on page 35 1040 Hard disk drive on page 36 1070 ODD board on page 41 1080 Fan and heat sink assembly on page 42 1090 Speaker on page 45 1100 RTC battery on page 46 1110 System board on page 47 1120 Upper case on page 49 1130 LCD unit on page 50 1140 EDP cable and integrated camera on page 52

Figure 15. Removal steps of LCD hinges

Remove the screws .

1 1 1

1 1 1

Step Screw (quantity) Color Torque M2.5 2.5 mm, Phillips head, nylok-coated (6) HINGE BRK TO LCD COVER

Black 30.3 kgf*cm

Release the two hinges in the direction shown by arrows .

2

2

55

Lenovo V145

Locations

Front and right-side view Integrated camera

Note:The position of the camera indicator on select models may vary slightly. Please refer to the actual product.

Built-in microphone Wireless LAN antennas Computer display Ventilation slots Touchpad Optical drive (on select models) Kensington mini security slot Power button

1 2 2

3

3

4

6

5

7

9

8

56

Lenovo V145 Hardware Maintenance Manual

Bottom and left-side view Speakers Louvers Power status indicator

Note: For the description of each indicator, see Status indicators on page 28. Memory card slot Novo button Combo audio connector USB connectors HDMI connector RJ-45 connector Battery status indicator

Note: For the description of each indicator, see Status indicators on page 28. ac power adapter connector

3

1

2 1

5 6

8 9

10 11

4

7

57

Lenovo V145

Parts list In Lenovo V145-14AST, this section presents the following service parts: "Overall" on page 58 "LCD FRUs" on page 61 "Miscellaneous parts" on page 62 "ac adapters" on page 62 "Screws" on page 63

In Lenovo V145-15AST, this section presents the following service parts: "Overall" on page 64 "LCD FRUs" on page 67 "Miscellaneous parts" on page 68 "ac adapters" on page 68 "Screws" on page 69

Note: Each FRU is available for all types or models, unless specific types or models are specified.

Attention: DonotattempttoreplaceanFRUonyourown.IfanFRUisdamaged,contact aLenovoauthorizedserviceroramarketingrepresentativeforreplacement orrepair.Onlyqualifiedtechnicianscaninspectorrepairthisproduct.

58

Lenovo V145 Hardware Maintenance Manual

Overall

Lenovo V145-14AST

1

2

3

5

4

7

8 d

12

13

14

9a

b

c

1011

6

59

Lenovo V145

Table 4. Parts listOverall (Lenovo V145-14AST)

No. FRU FRU no. CRU ID.

a-d See "Miscellaneous parts" on page 62. 1 LCD unit (see "LCD FRUs" on page 61.) 2 Upper Case ASM C 81MJ US 5CB0T24772 N 2 Upper Case ASM C 81MS ARA 5CB0T25421 N 2 Upper Case ASM C 81MS BEL 5CB0T25444 N 2 Upper Case ASM C 81MS BRA 5CB0T25435 N 2 Upper Case ASM C 81MS BUL 5CB0T25445 N 2 Upper Case ASM C 81MS CZ-SK 5CB0T25430 N 2 Upper Case ASM C 81MS ENG-FRA 5CB0T25454 N 2 Upper Case ASM C 81MS FRA 5CB0T25434 N 2 Upper Case ASM C 81MS FR-AR 5CB0T25423 N 2 Upper Case ASM C 81MS GER 5CB0T25453 N 2 Upper Case ASM C 81MS GRE 5CB0T25420 N 2 Upper Case ASM C 81MS HEB 5CB0T25451 N 2 Upper Case ASM C 81MS HUN 5CB0T25431 N 2 Upper Case ASM C 81MS ILD (ICE) 5CB0T25440 N 2 Upper Case ASM C 81MS INDIA 5CB0T25459 N 2 Upper Case ASM C 81MS ITA 5CB0T25456 N 2 Upper Case ASM C 81MS KOR 5CB0T25457 N 2 Upper Case ASM C 81MS LASPA 5CB0T25439 N 2 Upper Case ASM C 81MS NORDIC 5CB0T25460 N 2 Upper Case ASM C 81MS PORT 5CB0T25458 N 2 Upper Case ASM C 81MS RUS 5CB0T25422 N 2 Upper Case ASM C 81MS SLVN 5CB0T25428 N 2 Upper Case ASM C 81MS SPA 5CB0T25436 N 2 Upper Case ASM C 81MS SW 5CB0T25426 N 2 Upper Case ASM C 81MS TCH 5CB0T25441 N 2 Upper Case ASM C 81MS THAI 5CB0T25419 N 2 Upper Case ASM C 81MS TUR 5CB0T25455 N 2 Upper Case ASM C 81MS UK 5CB0T25449 N 2 Upper Case ASM C 81MS UKR 5CB0T25418 N 2 Upper Case ASM C 81MS USI 5CB0T25433 N 3 MB C 81MS NOK A4 DIS 5B20T25432 N 3 MB C 81MS NOK A4 UMA 5B20T25450 N 3 MB C 81MS NOK A6 DIS 5B20T25442 N 3 MB C 81MS NOK A6 UMA 5B20T25425 N 3 MB C 81MS NOK A9 DIS 5B20T25424 N 3 MB C 81MS NOK A9 UMA 5B20T25447 N 3 MB C 81MS NOK E2 UMA 5B20T25429 N 3 MB C 81MS WIN A4 DIS 5B20T25438 N 3 MB C 81MS WIN A4 UMA 5B20T25448 N 3 MB C 81MS WIN A6 DIS 5B20T25427 N 3 MB C 81MS WIN A6 UMA 5B20T25446 N 3 MB C 81MS WIN A9 DIS 5B20T25443 N 3 MB C 81MS WIN A9 UMA 5B20T25437 N 3 MB C 81MS WIN E2 UMA 5B20T25452 N

60

Lenovo V145 Hardware Maintenance Manual

No. FRU FRU no. CRU ID.

4 CMOS BATTERY C 81H7 5B10R34404 N 5 Heatsink C 81H5 DIS AMD 5H40R34399 N 5 Heatsink C 81H5 UMA AMD 5H40R34396 N 6 FAN C 81H7 5F10R34470 N 7 4GB DDR4 2666 SoDIMM,Micron 01AG831 N 7 4GB DDR4 2666 SODIMM,Ramaxel 01AG829 N 7 4GB DDR4 2666 SoDIMM,Samsung 01AG836 N 7 4GB DDR4 2666 SOIMM,Hynix 01AG823 N 7 8GB DDR4 2666 SoDIMM,Micron 01AG841 N 7 8GB DDR4 2666 SoDIMM,Ramaxel 01AG843 N 7 8GB DDR4 2666 SoDIMM,Samsung 01AG837 N 7 8GB DDR4 2666 SOIMM,Hynix 01AG824 N 8 Wireless,CMB,CBT,8821CE 01AX710 N 8 Wireless,CMB,LTN,NFA435A 01AX709 N 9 HL GUE1N 9.0 DVDWriter WOB 01MP404 * 9 HLDS GUE0N DVD RW 5DX0J46488 * 9 DA-8AESH 5DX0L08424 * 9 Dummy ODD C 81MJ 5M20T24780 * 9 2nd HDD BAY C 81MJ 5M20T24756 * 10 RW1D ST1000LM035 1T HDD 5H20L22184 N 10 Toshiba MQ01ABF050 500G HDD 5H20L34560 N 10 WD WD5000LPCX-24VHAT0 5H20J35762 N 10 Storage,HDD,1T,5400,7mm,SATA,WD 01FR402 N 10 Storage,HDD,500G,5400,7mm,ST 01FR401 N 10 Storage SSD CV8 128G 2.5'' Liteon 01FR549 N 10 Storage SSD PM871b 128G SAM 01FR502 N 10 Storage SSD SC313 128G Hynix 01FR514 N 11 HDD board C 81H6 W/FFC 5C50R34852 N 11 HDD board C 81H7 for 2nd HDD 5C50R34410 N 12 Speaker C 81H6 L+R 5SB0R34881 N 13 SP/A L16M2PB1 7.5V30Wh2cell 5B10M86148 N 13 SP/B L17M2PB7 7.56V30Wh2cell 5B10Q71253 N 13 CP/C L16C2PB2 7.6V30Wh2cell 5B10M88058 N 13 LG L17L2PF1 7.56V30Wh2cell bty 5B10Q41213 N 14 Lower case C 81MJ W/2nd HDD 5CB0T24755 N 14 Lower case C 81MJ W/O 2nd HDD 5CB0T24784 N ac adapter (see "ac adapters" on page 62).

Table 4. Parts listOverall (Lenovo V145-14AST) (continued)

61

Lenovo V145

LCD FRUs In Lenovo V145-14AST, there are following types of LCDs.

14.0-in. HD/FHD LED

3

2

1

4

6

7

5

62

Lenovo V145 Hardware Maintenance Manual

Table 5. Parts listLCD FRUs (Lenovo V145-14AST)

No. FRU FRU no. CRU ID.

1 LCD Bezel C 81MJ 5B30T24766 N 2 Hinge C 81H6 L+R 5H50R34870 N 2 Hinge Cover C 81MJ 5CB0T24761 N 3 AU B140HTN01.E 2A FHDT AG S NB 5D10L08701 N 3 AU B140XTN02.E HWCA HDT AG S NB 5D10P54235 N 3 BO NT140FHM-N41V8.0 FHDT AG S NB 5D10L01874 N 3 BO NT140WHM-N41 V8.0 HDT AG S NB 5D10K81099 N 3 IN N140BGA-EA3 HDT AG S NB 5D10K85755 N 3 IN N140HGE-EAA C4 FHDT AG S NB 5D10K93439 N 3 IN N140HGE-EAA C5 FHDT AG S NB 5D10R65299 N 3 IV M140NWR6 R1 HW1.2 HDT AG S NB 5D10Q95195 N 4 EDP cable C 81H6 5C10R34877 N 5 Camera C 81H7 0.3M 5C20R34402 N 5 Camera C 81H7 1M 5C20R34394 N 6 Hinge C 81H6 L+R 5H50R34870 N 6 Hinge Cover C 81MJ 5CB0T24761 N 7 LCD Cover C 81MJ W/Antenna 5CB0T24781 N

Miscellaneous parts Table 6. Parts listMiscellaneous parts (Lenovo V145-14AST)

FRU P/N CRU ID.

System miscellaneous parts: (a) ODD BRACKET C 81H7 5B40R34389 * (b) ODD BEZEL C 81MJ 5B30T24775 * (c) HDD Bracket C 81H7 5B40R34447 N (d) Wlan Sponge C 81H7 5T10R34434 N Note: Italicized letters in parentheses are references to the exploded view in "Overall" on page 58.

ac adapters Table 7. Parts listac adapters (Lenovo V145-14AST)

FRU P/N CRU ID.

ADL45WCB 20V2.25A COO 01FR127 * ADL45WCC 20V2.25A COO 01FR128 * ADL45WCD 20V2.25A COO 01FR129 * ADL45WCE 20V2.25A COO 01FR131 * ADL45WCF 20V2.25A COO 01FR132 * ADL45WCG 20V2.25A COO 01FR133 * ADL45WCH 20V2.25A COO 01FR134 * ADL45WCK 20V2.25A COO 01FR130 * ADLX65CCGA2A 20V3.25A COO 01FR158 * ADLX65CCGB2A 20V3.25A COO 01FR160 *

63

Lenovo V145

FRU P/N CRU ID.

ADLX65CCGE2A 20V3.25A COO 01FR159 * ADLX65CCGG2A 20V3.25A COO 01FR153 * ADLX65CCGI2A 20V3.25A COO 01FR156 * ADLX65CCGK2A 20V3.25A COO 01FR155 * ADLX65CCGR2A 20V3.25A COO 01FR157 * ADLX65CCGU2A 20V3.25A COO 01FR154 * ADLX65CDGA2A 20V3.25A COO 01FR141 * ADLX65CDGB2A 20V3.25A COO 01FR143 * ADLX65CDGE2A 20V3.25A COO 01FR142 * ADLX65CDGG2A 20V3.25A COO 01FR136 * ADLX65CDGI2A 20V3.25A COO 01FR139 * ADLX65CDGK2A 20V3.25A COO 01FR138 * ADLX65CDGR2A 20V3.25A COO 01FR140 * ADLX65CDGU2A 20V3.25A COO 01FR137 * ADLX65CLGA2A 20V3.25A COO 01FR149 * ADLX65CLGB2A 20V3.25A COO 01FR151 * ADLX65CLGE2A 20V3.25A COO 01FR150 * ADLX65CLGG2A 20V3.25A COO 01FR145 * ADLX65CLGI2A 20V3.25A COO 01FR147 * ADLX65CLGK2A 20V3.25A COO 01FR037 * ADLX65CLGR2A 20V3.25A COO 01FR148 * ADLX65CLGU2A 20V3.25A COO 01FR146 * ADP-45DW B 20V2.25A COO 01FR111 * ADP-45DW C 20V2.25A COO 01FR116 * ADP-45DW D 20V2.25A COO 01FR112 * ADP-45DW E 20V2.25A COO 01FR115 * ADP-45DW G 20V2.25A COO 01FR114 * ADP-45DW H 20V2.25A COO 01FR113 * ADP-45DW J 20V2.25A COO 01FR110 * ADP-45DW K 20V2.25A COO 01FR117 * PA-1450-55LG 20V2.25A COO 01FR119 * PA-1450-55LI 20V2.25A COO 01FR121 * PA-1450-55LK 20V2.25A COO 01FR036 * PA-1450-55LL 20V2.25A COO 01FR120 * PA-1450-55LR 20V2.25A COO 01FR122 * PA-1450-55LS 20V2.25A COO 01FR123 * PA-1450-55LU 20V2.25A COO 01FR124 * PA-1450-55LZ 20V2.25A COO 01FR125 *

Screws Table 8. Parts listScrews (Lenovo V145-14AST)

FRU P/N CRU ID.

Screw pack C 81H6 5S10R34864 N

Table 7. Parts listac adapters (Lenovo V145-14AST) (continued)

64

Lenovo V145 Hardware Maintenance Manual

Overall

Lenovo V145-15AST

1

2

3

6

5

8

9 d

13

14

15

10a

4

b

c

1112

7

65

Lenovo V145

Table 9. Parts listOverall (Lenovo V145-15AST)

No. FRU FRU no. CRU ID.

a-d See "Miscellaneous parts" on page 68. 1 LCD unit (see "LCD FRUs" on page 67.) 2 Upper Case ASM C 81MK US 5CB0T24804 N 2 Upper Case ASM C 81MT ARA 5CB0T25496 N 2 Upper Case ASM C 81MT BEL 5CB0T25484 N 2 Upper Case ASM C 81MT BRA 5CB0T25467 N 2 Upper Case ASM C 81MT BUL 5CB0T25468 N 2 Upper Case ASM C 81MT CZ-SK 5CB0T25486 N 2 Upper Case ASM C 81MT ENG-FRA 5CB0T25471 N 2 Upper Case ASM C 81MT FRA 5CB0T25485 N 2 Upper Case ASM C 81MT FR-AR 5CB0T25479 N 2 Upper Case ASM C 81MT GER 5CB0T25497 N 2 Upper Case ASM C 81MT GRE 5CB0T25492 N 2 Upper Case ASM C 81MT HEB 5CB0T25474 N 2 Upper Case ASM C 81MT HUN 5CB0T25498 N 2 Upper Case ASM C 81MT ILD (ICE) 5CB0T25500 N 2 Upper Case ASM C 81MT INDIA 5CB0T25487 N 2 Upper Case ASM C 81MT ITA 5CB0T25473 N 2 Upper Case ASM C 81MT KOR 5CB0T25506 N 2 Upper Case ASM C 81MT LASPA 5CB0T25480 N 2 Upper Case ASM C 81MT NORDIC 5CB0T25491 N 2 Upper Case ASM C 81MT PORT 5CB0T25477 N 2 Upper Case ASM C 81MT RUS 5CB0T25482 N 2 Upper Case ASM C 81MT SLVN 5CB0T25478 N 2 Upper Case ASM C 81MT SPA 5CB0T25472 N 2 Upper Case ASM C 81MT SW 5CB0T25509 N 2 Upper Case ASM C 81MT TCH 5CB0T25493 N 2 Upper Case ASM C 81MT THAI 5CB0T25476 N 2 Upper Case ASM C 81MT TUR 5CB0T25502 N 2 Upper Case ASM C 81MT UK 5CB0T25489 N 2 Upper Case ASM C 81MT UKR 5CB0T25501 N 2 Upper Case ASM C 81MT USI 5CB0T25490 N 3 MB C 81MT NOK A4 DIS 5B20T25495 N 3 MB C 81MT NOK A4 UMA 5B20T25469 N 3 MB C 81MT NOK A6 DIS 5B20T25505 N 3 MB C 81MT NOK A6 UMA 5B20T25494 N 3 MB C 81MT NOK A9 DIS 5B20T25488 N 3 MB C 81MT NOK A9 UMA 5B20T25504 N 3 MB C 81MT NOK E2 UMA 5B20T25483 N 3 MB C 81MT WIN A4 DIS 5B20T25481 N 3 MB C 81MT WIN A4 UMA 5B20T25470 N 3 MB C 81MT WIN A6 DIS 5B20T25503 N 3 MB C 81MT WIN A6 UMA 5B20T25499 N 3 MB C 81MT WIN A9 DIS 5B20T25508 N 3 MB C 81MT WIN A9 UMA 5B20T25507 N 3 MB C 81MT WIN E2 UMA 5B20T25475 N

66

Lenovo V145 Hardware Maintenance Manual

No. FRU FRU no. CRU ID.

4 ODD Switch Board C 81H7 W/FFC 5C50R34463 N 5 CMOS BATTERY C 81H7 5B10R34404 N 6 Heatsink C 81H5 DIS AMD 5H40R34399 N 6 Heatsink C 81H5 UMA AMD 5H40R34396 N 7 FAN C 81H7 5F10R34470 N 8 4GB DDR4 2666 SoDIMM,Micron 01AG831 N 8 4GB DDR4 2666 SODIMM,Ramaxel 01AG829 N 8 4GB DDR4 2666 SoDIMM,Samsung 01AG836 N 8 4GB DDR4 2666 SOIMM,Hynix 01AG823 N 8 8GB DDR4 2666 SoDIMM,Micron 01AG841 N 8 8GB DDR4 2666 SoDIMM,Ramaxel 01AG843 N 8 8GB DDR4 2666 SoDIMM,Samsung 01AG837 N 8 8GB DDR4 2666 SOIMM,Hynix 01AG824 N 9 Wireless,CMB,CBT,8821CE 01AX710 N 9 Wireless,CMB,LTN,NFA435A 01AX709 N 10 HL GUE1N 9.0 DVDWriter WOB 01MP404 * 10 HLDS GUE0N DVD RW 5DX0J46488 * 10 DA-8AESH 5DX0L08424 * 10 Dummy ODD C 81MJ 5M20T24780 * 10 2nd HDD BAY C 81MJ 5M20T24756 * 11 RW1D ST1000LM035 1T HDD 5H20L22184 N 11 Toshiba MQ01ABF050 500G HDD 5H20L34560 N 11 WD WD5000LPCX-24VHAT0 5H20J35762 N 11 Storage SSD CV8 128G 2.5'' Liteon 01FR549 N 11 Storage SSD PM871b 128G SAM 01FR502 N 11 Storage SSD SC313 128G Hynix 01FR514 N 11 Storage,HDD,1T,5400,7mm,SATA,WD 01FR402 N 11 Storage,HDD,500G,5400,7mm,ST 01FR401 N 12 HDD board C 81H7 for 2nd HDD 5C50R34410 N 12 HDD board C 81H7 W/FFC 5C50R34420 N 13 Speaker C 81H7 L+R 5SB0R34474 N 14 SP/A L16M2PB1 7.5V30Wh2cell 5B10M86148 N 14 SP/B L17M2PB7 7.56V30Wh2cell 5B10Q71253 N 14 CP/C L16C2PB2 7.6V30Wh2cell 5B10M88058 N 14 LG L17L2PF1 7.56V30Wh2cell bty 5B10Q41213 N 15 Lower case C 81MK W/2nd HDD 5CB0T24811 N 15 Lower case C 81MK W/O 2nd HDD 5CB0T24808 N ac adapter (see "ac adapters" on page 68).

Table 9. Parts listOverall (Lenovo V145-15AST) (continued)

67

Lenovo V145

LCD FRUs In Lenovo V145-15AST, there are following types of LCDs.

15.6-in. HD/FHD LED

3

2

1

4

6

7

5

68

Lenovo V145 Hardware Maintenance Manual

Table 10. Parts listLCD FRUs (Lenovo V145-15AST)

No. FRU FRU no. CRU ID.

1 LCD Bezel C 81MK 5B30T24815 N 2 Hinge Cover C 81MK 5CB0T24798 N 3 AU B156HTN03.8 0C FHDT AG S NB 5D10L08702 N 3 AU B156XTN07.1 3A HDT AG S NB 5D10H52713 N 3 BO NT156FHM-N41 FHDT AG S NB 5D10K93434 N 3 BO NT156FHM-N41V8.1 FHDT AG S NB 5D10Q90268 N 3 BO NT156WHM-N42 V8 HDT AG S NB 5D10K81097 N 3 IN N156BGA-EA2 HDT AG S NB 5D10K81086 N 3 IN N156HGA-EAB C2 FHDT AG S NB 5D10R65303 N 3 IN N156HGA-EAB FHDT AG S NB 5D10K93435 N 4 EDP cable C 81H7 5C10R34473 N 5 Camera C 81H7 0.3M 5C20R34402 N 5 Camera C 81H7 1M 5C20R34394 N 6 Hinge C 81H7 L+R 5H50R34445 N 7 LCD Cover C 81MK W/Antenna 5CB0T24812 N

Miscellaneous parts Table 11. Parts listMiscellaneous parts (Lenovo V145-15AST)

FRU P/N CRU ID.

System miscellaneous parts: (a) ODD BRACKET C 81H7 5B40R34389 * (b) ODD BEZEL C 81MJ 5B30T24775 * (c) HDD Bracket C 81H7 5B40R34447 N (d) Wlan Sponge C 81H7 5T10R34434 N Note: Italicized letters in parentheses are references to the exploded view in "Overall" on page 64.

ac adapters Table 12. Parts listac adapters (Lenovo V145-15AST)

FRU P/N CRU ID.

ADL45WCB 20V2.25A COO 01FR127 * ADL45WCC 20V2.25A COO 01FR128 * ADL45WCD 20V2.25A COO 01FR129 * ADL45WCE 20V2.25A COO 01FR131 * ADL45WCF 20V2.25A COO 01FR132 * ADL45WCG 20V2.25A COO 01FR133 * ADL45WCH 20V2.25A COO 01FR134 * ADL45WCK 20V2.25A COO 01FR130 * ADLX65CCGA2A 20V3.25A COO 01FR158 * ADLX65CCGB2A 20V3.25A COO 01FR160 * ADLX65CCGE2A 20V3.25A COO 01FR159 * ADLX65CCGG2A 20V3.25A COO 01FR153 * ADLX65CCGI2A 20V3.25A COO 01FR156 * ADLX65CCGK2A 20V3.25A COO 01FR155 *

69

Lenovo V145

FRU P/N CRU ID.

ADLX65CCGR2A 20V3.25A COO 01FR157 * ADLX65CCGU2A 20V3.25A COO 01FR154 * ADLX65CDGA2A 20V3.25A COO 01FR141 * ADLX65CDGB2A 20V3.25A COO 01FR143 * ADLX65CDGE2A 20V3.25A COO 01FR142 * ADLX65CDGG2A 20V3.25A COO 01FR136 * ADLX65CDGI2A 20V3.25A COO 01FR139 * ADLX65CDGK2A 20V3.25A COO 01FR138 * ADLX65CDGR2A 20V3.25A COO 01FR140 * ADLX65CDGU2A 20V3.25A COO 01FR137 * ADLX65CLGA2A 20V3.25A COO 01FR149 * ADLX65CLGB2A 20V3.25A COO 01FR151 * ADLX65CLGE2A 20V3.25A COO 01FR150 * ADLX65CLGG2A 20V3.25A COO 01FR145 * ADLX65CLGI2A 20V3.25A COO 01FR147 * ADLX65CLGK2A 20V3.25A COO 01FR037 * ADLX65CLGR2A 20V3.25A COO 01FR148 * ADLX65CLGU2A 20V3.25A COO 01FR146 * ADP-45DW B 20V2.25A COO 01FR111 * ADP-45DW C 20V2.25A COO 01FR116 * ADP-45DW D 20V2.25A COO 01FR112 * ADP-45DW E 20V2.25A COO 01FR115 * ADP-45DW G 20V2.25A COO 01FR114 * ADP-45DW H 20V2.25A COO 01FR113 * ADP-45DW J 20V2.25A COO 01FR110 * ADP-45DW K 20V2.25A COO 01FR117 * PA-1450-55LG 20V2.25A COO 01FR119 * PA-1450-55LI 20V2.25A COO 01FR121 * PA-1450-55LK 20V2.25A COO 01FR036 * PA-1450-55LL 20V2.25A COO 01FR120 * PA-1450-55LR 20V2.25A COO 01FR122 * PA-1450-55LS 20V2.25A COO 01FR123 * PA-1450-55LU 20V2.25A COO 01FR124 * PA-1450-55LZ 20V2.25A COO 01FR125 *

Screws Table 13. Parts listScrews (Lenovo V145-15AST)

FRU P/N CRU ID.

Screw pack C 81H7 5S10R34464 N

Table 12. Parts listac adapters (Lenovo V145-15AST) (continued)

70

Lenovo V145 Hardware Maintenance Manual

Notices

Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the users responsibility to evaluate and verify the operation of any other product, program, or service. Lenovo may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents.

LENOVO GROUP LTD. PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON- INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you. This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. The result obtained in other operating environments may vary. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk.

Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.

71

Notices

Trademarks The following terms are trademarks or registered trademarks of Lenovo in the United States, other countries, or both. Lenovo

Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both.

Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the U. S. and/or other countries.

Wi-Fi is a re

Manualsnet FAQs

If you want to find out how the V145–14AST Lenovo works, you can view and download the Lenovo V145–14AST Laptop Hardware Maintenance Manual on the Manualsnet website.

Yes, we have the Hardware Maintenance Manual for Lenovo V145–14AST as well as other Lenovo manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Hardware Maintenance Manual should include all the details that are needed to use a Lenovo V145–14AST. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Lenovo V145–14AST Laptop Hardware Maintenance Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Lenovo V145–14AST Laptop Hardware Maintenance Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Lenovo V145–14AST Laptop Hardware Maintenance Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Lenovo V145–14AST Laptop Hardware Maintenance Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Lenovo V145–14AST Laptop Hardware Maintenance Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.