Contents

Lenovo ThinkPad T550 Laptop Hardware Maintenance Manual PDF

1 of 114
1 of 114

Summary of Content for Lenovo ThinkPad T550 Laptop Hardware Maintenance Manual PDF

Hardware Maintenance Manual

ThinkPad T550 and W550s

Note: Before using this information and the product it supports, be sure to read the general information under Appendix A Notices on page 105.

Third Edition (July 2015)

Copyright Lenovo 2015.

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.

Contents

About this manual. . . . . . . . . . . iii

Chapter 1. Safety information. . . . . . 1 General safety . . . . . . . . . . . . . . . . 1 Electrical safety . . . . . . . . . . . . . . . 1 Safety inspection guide . . . . . . . . . . . . 2 Handling devices that are sensitive to electrostatic discharge. . . . . . . . . . . . . . . . . . 3 Grounding requirements . . . . . . . . . . . . 4 Safety notices (multilingual translations) . . . . . . 4

Chapter 2. Important service information . . . . . . . . . . . . . . 19 Strategy for replacing FRUs . . . . . . . . . 19

Strategy for replacing a solid-state drive . . . 19 Important notice for replacing a system board . . . . . . . . . . . . . . . . 20 How to use error message . . . . . . . . 20

Strategy for replacing FRUs for CTO, special-bid, and standard models . . . . . . . . . . . . 20

Product definition. . . . . . . . . . . . 20 FRU identification. . . . . . . . . . . . 20

Chapter 3. General checkout . . . . . 23 What to do first . . . . . . . . . . . . . . 23 Checkout guide . . . . . . . . . . . . . . 24

Lenovo Solution Center . . . . . . . . . 24 Quick test programs. . . . . . . . . . . 24 UEFI diagnostic program . . . . . . . . . 25 Bootable diagnostic programs. . . . . . . 25

Power system checkout . . . . . . . . . . . 26 Checking the ac power adapter . . . . . . 26 Checking the battery and operational charging . . . . . . . . . . . . . . . 27 Checking the coin-cell battery . . . . . . . 27

Chapter 4. Related service information . . . . . . . . . . . . . . 29 Restoring the factory contents by using the product Recovery Disc Set . . . . . . . . . . 29 Using the Windows recovery programs on the Windows 8.1 operating system . . . . . . . . 30 Recovery overview for the Windows 10 operating system. . . . . . . . . . . . . . . . . . 32

Resetting your computer . . . . . . . . . 32 Using advanced startup options . . . . . . 33 Recovering your operating system if Windows 10 fails to start . . . . . . . . . . . . . 33 Creating and using a recovery USB drive . . 33

Passwords . . . . . . . . . . . . . . . . 34 Power-on password . . . . . . . . . . . 34 Hard disk password . . . . . . . . . . . 34 Supervisor password . . . . . . . . . . 34 How to remove the power-on password . . . 35 How to remove the hard disk password . . . 35

Power management . . . . . . . . . . . . 36 Screen blank mode (for the Windows 7 operating system only) . . . . . . . . . . 36 Sleep mode . . . . . . . . . . . . . . 36 Hibernation mode . . . . . . . . . . . 37

Symptom-to-FRU index . . . . . . . . . . . 37 Numeric error codes . . . . . . . . . . 38 Error messages . . . . . . . . . . . . 39 Beep symptoms . . . . . . . . . . . . 39 No-beep symptoms . . . . . . . . . . . 39 LCD-related symptoms . . . . . . . . . 40 Intermittent problems . . . . . . . . . . 40 Undetermined problems . . . . . . . . . 40

Chapter 5. Locations . . . . . . . . . 43 Locating computer controls, connectors, and indicators. . . . . . . . . . . . . . . . . 43

Front view. . . . . . . . . . . . . . . 43 Left-side view . . . . . . . . . . . . . 44 Bottom view . . . . . . . . . . . . . . 44

Locating FRUs and CRUs . . . . . . . . . . 45 Major FRUs . . . . . . . . . . . . . . 46 LCD FRUs . . . . . . . . . . . . . . 47 Miscellaneous parts and other FRUs . . . . 50

Looking up FRU information . . . . . . . . . 51

Chapter 6. FRU replacement notices . . . . . . . . . . . . . . . . 53 Common service tools . . . . . . . . . . . 53 Screw notices . . . . . . . . . . . . . . . 53 Retaining serial numbers. . . . . . . . . . . 54

Restoring the serial number of the system unit . . . . . . . . . . . . . . . . . 54 Retaining the UUID . . . . . . . . . . . 55 Reading or writing the ECA information . . . 56

Chapter 7. Removing or replacing a FRU . . . . . . . . . . . . . . . . . . 57 General guidelines . . . . . . . . . . . . . 57 Before servicing the computer . . . . . . . . 58

Disabling the built-in battery . . . . . . . 58

Copyright Lenovo 2015 i

Removing the micro SIM card . . . . . . . 58 Removing a major FRU . . . . . . . . . . . 58

1010 Removable battery . . . . . . . . . 59 1020 Base cover assembly . . . . . . . . 59 1030 Keyboard. . . . . . . . . . . . . 61 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive bracket. . . . . . . . . . . . 66 1050 Memory module . . . . . . . . . . 68 1060 Wireless LAN card . . . . . . . . . 68 1070 Wireless WAN card . . . . . . . . . 69 1080 M.2 solid-state drive . . . . . . . . 70 1090 Coin-cell battery . . . . . . . . . . 71 1110 dc-in bracket and dc-in cable assembly . . . . . . . . . . . . . . . 72 1120 Built-in battery or dummy battery . . . 73 1130 Thermal fan . . . . . . . . . . . . 75 1140 Speaker assembly . . . . . . . . . 77 1150 Smart card assembly or dummy smart card . . . . . . . . . . . . . . . . . 78 1160 Fingerprint reader assembly . . . . . 79 1170 Board for the trackpad and TrackPoint buttons . . . . . . . . . . . . . . . . 80 1180 System board assembly . . . . . . . 81 1190 LCD unit . . . . . . . . . . . . . 83

1210 Power button board . . . . . . . . 85 1220 Keyboard assembly. . . . . . . . . 86

Removing an LCD FRU for models without touch panel . . . . . . . . . . . . . . . . . . 86

2010 LCD bezel assembly . . . . . . . . 87 2020 LCD panel and LCD cable . . . . . . 87 2030 Hinges and hinge brackets . . . . . . 89 2040 Camera/microphone card . . . . . . 90 2050 LED cable assembly . . . . . . . . 91 2060 Antenna kit and LCD rear cover assembly . . . . . . . . . . . . . . . 92

Removing an LCD FRU for models with touch panel . . . . . . . . . . . . . . . . . . 95

3010 LCD front sheet bezel . . . . . . . . 95 3020 LCD panel assembly and LCD cable . . 95 3030 Hinges . . . . . . . . . . . . . . 97 3040 Camera/microphone card . . . . . . 98 3050 Touch sensor card . . . . . . . . . 99 3060 LED cable assembly . . . . . . . . 100 3070 Antenna kit and LCD rear cover assembly . . . . . . . . . . . . . . . 101

Appendix A. Notices. . . . . . . . . 105 Electronic emissions notices . . . . . . . . . 106 Trademarks . . . . . . . . . . . . . . . . 106

ii Hardware Maintenance Manual

About this manual

This manual contains service and reference information for the following ThinkPad products.

ThinkPad T550 Machine types (MT): 20CJ and 20CK

ThinkPad W550s MT: 20E1 and 20E2

Use this manual along with the advanced diagnostic tests to troubleshoot problems.

Important: This manual is intended only for trained service technicians who are familiar with ThinkPad products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively. Before servicing a ThinkPad product, be sure to read all the information under Chapter 1 Safety information on page 1 and Chapter 2 Important service information on page 19.

Copyright Lenovo 2015 iii

iv Hardware Maintenance Manual

Chapter 1. Safety information

This chapter presents following safety information that you must be familiar with before you service a ThinkPad notebook computer. General safety on page 1 Electrical safety on page 1 Safety inspection guide on page 2 Handling devices that are sensitive to electrostatic discharge on page 3 Grounding requirements on page 4 Safety notices (multilingual translations) on page 4

General safety Follow these rules to ensure general safety: Observe good housekeeping in the area of the machines during and after maintenance. When lifting any heavy object:

1. Make sure that you can stand safely without slipping.

2. Distribute the weight of the object equally between your feet.

3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.

4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you.

Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe. Before you start the machine, make sure that other service technicians and the customer's personnel are

not in a hazardous position. Place removed covers and other parts in a safe place, away from all personnel, while you are servicing

the machine. Keep your toolcase away from walk areas so that other people will not trip over it. Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your

sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it. Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8

centimeters (3 inches) from the end. Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.

Attention: Metal objects are good electrical conductors. Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using

solvents, or working in any other conditions that might be hazardous to your eyes. After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device

that is worn or defective. Reinstall all covers correctly before returning the machine to the customer. Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan

louvers or cover them with labels or stickers.

Electrical safety Observe the following rules when working on electrical equipment.

Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents.Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.

Copyright Lenovo 2015 1

Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.

Do not work alone under hazardous conditions or near equipment that has hazardous voltages. Disconnect all power before:

Performing a mechanical inspection Working near power supplies Removing or installing main units

Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.

If you have to work on a machine that has exposed electrical circuits, observe the following precautions: Ensure that another person, familiar with the power-off controls, is near you.

Attention: Another person must be there to switch off the power, if necessary. Use only one hand when working with powered-on electrical equipment; keep the other hand in your

pocket or behind your back.

Attention: An electrical shock can occur only when there is a complete circuit. By observing the above rule, you may prevent a current from passing through your body.

When using testers, set the controls correctly and use the approved probe leads and accessories for that tester.

Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages; Instructions for these precautions are in the safety sections of maintenance information. Use extreme care when measuring high voltages.

Regularly inspect and maintain your electrical hand tools for safe operational condition. Do not use worn or broken tools and testers. Never assume that power has been disconnected from a circuit. First, check that it has been powered off. Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,

nongrounded power extension cables, power surges, and missing safety grounds. Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is

conductive; such touching can cause personal injury and machine damage. Do not service the following parts with the power on when they are removed from their normal operating

places in a machine: Power supply units Pumps Blowers and fans Motor generators Similar units as listed above This practice ensures correct grounding of the units.

If an electrical accident occurs: Use caution; do not become a victim yourself. Switch off power. Send another person to get medical aid.

Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.

2 Hardware Maintenance Manual

Consider these conditions and the safety hazards they present: Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal

electrical shock) Explosive hazards, such as a damaged CRT face or a bulging capacitor Mechanical hazards, such as loose or missing hardware

To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning of every service task. Begin the checks with the power off, and the power cord disconnected.

Checklist:

1. Check exterior covers for damage (loose, broken, or sharp edges).

2. Power off the computer. Disconnect the power cord.

3. Check the power cord for:

a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground.

b. The power cord should be the authorized type specified for your computer. Go to: http://www.lenovo.com/serviceparts-lookup

c. Insulation must not be frayed or worn.

4. Check for cracked or bulging batteries.

5. Remove the cover.

6. Check for any obvious non-ThinkPad alterations. Use good judgment as to the safety of any non-ThinkPad alterations.

7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.

8. Check for worn, frayed, or pinched cables.

9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.

Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.

Notes:

1. Use product-specific ESD procedures when they exceed the requirements noted here.

2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.

When handling ESD-sensitive parts: Keep the parts in protective packages until they are inserted into the product. Avoid contact with other people. Wear a grounded wrist strap against your skin to eliminate static on your body. Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even

when you are wearing a wrist strap. Use a grounded work mat to provide a static-free work surface. The mat is especially useful when

handling ESD-sensitive devices. Select a grounding system, such as those listed below, to provide protection that meets the specific

service requirement.

Note: The use of a grounding system to guard against ESD damage is desirable but not necessary. Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.

Chapter 1. Safety information 3

When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector-outside shells on these systems.

Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.

Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: English Arabic Brazilian Portuguese French German Hebrew Japanese Korean Spanish Traditional Chinese

DANGER

DANGER

DANGER

4 Hardware Maintenance Manual

DANGER

DANGER

DANGER

DANGER

DANGER

Chapter 1. Safety information 5

6 Hardware Maintenance Manual

PERIGO

PERIGO

PERIGO

PERIGO

Chapter 1. Safety information 7

PERIGO

PERIGO

PERIGO

PERIGO

DANGER

8 Hardware Maintenance Manual

DANGER

DANGER

DANGER

DANGER

DANGER

DANGER

Chapter 1. Safety information 9

DANGER

VORSICHT

VORSICHT

VORSICHT

VORSICHT

10 Hardware Maintenance Manual

VORSICHT

VORSICHT

VORSICHT

VORSICHT

Chapter 1. Safety information 11

12 Hardware Maintenance Manual

Chapter 1. Safety information 13

14 Hardware Maintenance Manual

Chapter 1. Safety information 15

16 Hardware Maintenance Manual

Chapter 1. Safety information 17

18 Hardware Maintenance Manual

Chapter 2. Important service information

This chapter introduces following important service information that applies to all machine types supported by this manual: Strategy for replacing FRUs on page 19

Strategy for replacing a solid-state drive on page 19 Important notice for replacing a system board on page 20 How to use error message on page 20

Strategy for replacing FRUs for CTO, special-bid, and standard models on page 20 Product definition on page 20 FRU identification on page 20

Important: Advise customers to contact the Lenovo Support Web site at http://www.lenovo.com/support to view

the software fixes, download the drivers, and follow the on-screen instructions to install the drivers. For additional assistance, customers might call the Lenovo Customer Support Center. Telephone numbers for the Lenovo Support Center are available at: http://www.lenovo.com/support/phone

Service training documents for Lenovo authorized service technicians are available at the following Web site. The disassembly and reassembly videos that show the FRU removal and replacement procedures are contained in the documents. http://www.lenovoservicetraining.com

Strategy for replacing FRUs Before replacing parts:

Ensure that all software fixes, drivers, and UEFI BIOS downloads are installed before replacing any FRUs listed in this manual.

After a system board is replaced, ensure that the latest UEFI BIOS is loaded to the system board before completing the service action.

To download software fixes, drivers, and UEFI BIOS, go to http://www.lenovo.com/ThinkPadDrivers and follow the instructions on the screen.

Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the

original FRU before you continue. Some computers have both a processor board and a system board. If you are instructed to replace either

the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one.

If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change. Replace only the FRU that changed the symptoms.

Strategy for replacing a solid-state drive Always try to run a low-level format before replacing a solid-state drive. This will cause all customer data on the solid-state drive to be lost. Be sure that the customer has a current backup of the data before doing this task.

Copyright Lenovo 2015 19

Attention: The drive startup sequence in the computer you are servicing may have been changed. Be extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect drive, data or programs can be overwritten.

Important notice for replacing a system board Some components mounted on a system board are very sensitive. Improper handling of a system board can cause damage to those components, and may cause a system malfunction.

Attention: When handling a system board: Do not drop a system board or apply any excessive force to it. Avoid rough handling of any kind. Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.

How to use error message Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed, begin the diagnosis with the first error code. Whatever causes the first error code may also cause false error codes. If no error code is displayed, see whether the error symptom is listed in the Symptom-to-FRU Index for the computer you are servicing.

Strategy for replacing FRUs for CTO, special-bid, and standard models This topic provides information about the model types and FRU identification.

Product definition This topic introduces different model types and how to identify each type.

Dynamic configure-to-order (CTO) model

This model provides the ability for a customer to configure a Lenovo solution from a Web Site, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label and eSupport will load these products as the 4-character MT, 4-character model, and 2-character country code. The model is CTO1 and the default country code is WW (example: 20A7CTO1WW).

Special-bid model

This is a unique configuration that has been negotiated between Lenovo and the customer. A unique machine type model (MTM) consists of a 4-character MT, a 4-character model, and a numeric 2-character country code is provided to the customer to place orders (example: 20A7000955). The country code assigned is numeric and does not designate a specific country or region. The custom model factsheet for the MTM indicates which country the special bid MTM is set up for. Special-bid offering is not generally announced.

Standard model

Standard models (fixed configuration) are announced and offered to all customers. The MTM portion of the machine label consists of a 4-character MT, a 4-character model, and an alphabetic 2-character country code. The country code assigned is alphabetic and represents a designated country or region (example: 20A70009UK).

FRU identification Use Lenovo eSupport to identify major FRUs, FRU part numbers, and FRU descriptions for a product at an MT - serial number level. Examples of major FRUs are hard disk drive, system board, and liquid crystal display (LCD).

To identify the major FRUs for a product, do the following:

20 Hardware Maintenance Manual

1. Go to http://support.lenovo.com/ibasepartslookup.

2. Type the Machine Type and Serial Number in the corresponding fields.

3. Click Submit.

eSupport also can be used to view the general FRU list for a product. The FRU list is a general list of components and does not contain specific model information.

To get the general FRU list for a product, do the following:

1. Go to http://www.lenovo.com/support.

2. Follow the instructions on the screen to select a product.

3. Click the Product & Parts tab.

4. Select System Service Parts to view a general FRU list.

Chapter 2. Important service information 21

22 Hardware Maintenance Manual

Chapter 3. General checkout

This chapter introduces following information: What to do first on page 23 Checkout guide on page 24

Lenovo Solution Center on page 24 Quick test programs on page 24 UEFI diagnostic program on page 25 Bootable diagnostic programs on page 25

Power system checkout on page 26

Before you go to the checkout guide, be sure to read the following important notes.

Important notes: Only certified trained personnel should service the computer. Before replacing any FRU, read the entire page on removing and replacing FRUs. When you replace FRUs, it is recommended use new nylon-coated screws. Be extremely careful during such write operations as copying, saving, or formatting. The sequence

of the drives in the computer that you are servicing might have been altered. If you select an incorrect drive, data or programs might be overwritten.

Replace a FRU only with another FRU of the correct model. When you replace a FRU, ensure that the model of the machine and the FRU part number are correct by referring to the web site: http://www.lenovo.com/serviceparts-lookup

A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for various reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear the error log and run the test again. If the error does not recur, do not replace the FRU.

Be careful not to replace a nondefective FRU.

What to do first When you return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it:

1. Name and phone number of service technician

2. Date of service

3. Date on which the machine failed

4. Date of purchase

5. Failure symptoms, error codes appearing on the display, and beep symptoms

6. Procedure index and page number in which the failing FRU was detected

7. Failing FRU name and part number

8. Machine type, model number, and serial number

9. Customer's name and address

Note: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer. Following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use.

Copyright Lenovo 2015 23

Before checking problems with the computer, determine whether the damage is covered under the warranty by referring to the following list:

The following are not covered under warranty: LCD panel cracked from the application of excessive force or from being dropped Scratched (cosmetic) parts Distortion, deformation, or discoloration of the cosmetic parts Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force Damage caused by liquid spilled into the system Damage caused by the improper insertion of a PC card or the installation of an incompatible card Improper disc insertion or use of an optical drive Fuses blown by attachment of a nonsupported device Forgotten computer password (making the computer unusable) Sticky keys caused by spilling a liquid onto the keyboard Use of an incorrect ac power adapter on laptop products

The following symptoms might indicate damage caused by nonwarranted activities: Missing parts might be a symptom of unauthorized service or modification. Check for obvious damage to a hard disk drive. If the spindle of a hard disk drive becomes noisy, the hard

disk drive might have been dropped or subject to excessive force.

Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad notebook computers.

Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses.

1. Identify the failing symptoms in as much detail as possible.

2. Verify the symptoms. Try to re-create the failure by running the diagnostic test or by repeating the operation.

Lenovo Solution Center The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems. It combines diagnostic tests, system information collection, security status, and support information, along with hints and tips for maximum system performance.

The Lenovo Solution Center program is available for download at http://www.lenovo.com/diags.

To run the Lenovo Solution Center program, go to Control Panel and click System and Security Lenovo - System Health and Diagnostics, and then follow the instructions on the screen.

For more information about the Lenovo Solution Center program, refer to the help information system of the program.

Quick test programs Lenovo provides quick test programs to troubleshoot and resolve computer problems, especially when the computer does not have the Lenovo Solution Center program installed.

To download and install a quick test program, go to http://www.lenovo.com/diags, and follow the instructions on the Web site.

To run a test using quick test program, do the following:

24 Hardware Maintenance Manual

1. Go to the C:\SWTOOLS\ldiag directory.

2. Double-click the gui_lsc_lite.exe file.

3. When the User Account Control window opens, click Yes.

4. Select the device class to be tested.

5. Select the devices to be tested.

6. Select the test to be performed.

7. Follow the instructions on the screen to start the test. When a problem is detected, information messages are displayed. Refer to the messages to troubleshoot the problem.

UEFI diagnostic program A UEFI diagnostic program is preinstalled on the computer. It enables you to test internal storage devices, view system information, and check and recover bad sectors on internal storage devices.

To run the UEFI diagnostic program, do the following:

1. Turn on the computer. If the computer cannot be turned on, go to Power system checkout on page 26, and check the power sources. If an error code is displayed, go to Symptom-to-FRU index on page 37 for error code descriptions and troubleshooting hints.

2. When the ThinkPad logo is displayed, repeatedly press and release the F10 key. The main screen of the UEFI diagnostic program is displayed.

3. Follow the instructions on the screen to use the diagnostic program.

Bootable diagnostic programs If the computer you are servicing is not installed with the UEFI diagnostic program, you can download a bootable diagnostic program from the Lenovo Support Web site. The bootable diagnostic programs enable you to test computer memory and internal storage devices, view system information, and check and recover the internal storage devices. To use the bootable diagnostic programs, you can create a bootable diagnostic medium on a USB device or CD.

To create a bootable diagnostic medium, do the following:

1. Go to http://www.lenovo.com/diags.

2. Click Lenovo Bootable Diagnostics.

3. Follow the instructions on the Web site to create a bootable diagnostic medium on a USB device or CD.

To use the diagnostic medium you have created, do one of the following: If you have created the bootable diagnostic medium on a USB device, do the following:

1. Attach the USB device to the computer.

2. Turn on the computer. If the computer cannot be turned on, go to Power system checkout on page 26, and check the power sources. If an error code is displayed, go to Symptom-to-FRU index on page 37 for error code descriptions and troubleshooting hints.

3. When the ThinkPad logo is displayed, repeatedly press and release the F12 key. When the Boot Menu window opens, release the F12 key.

4. Use the arrow keys to select USB HDD and then press Enter. The diagnostic program will be launched automatically.

5. Follow the instructions on the screen to use the diagnostic program. If you have created the bootable diagnostic medium on a CD, do the following:

Chapter 3. General checkout 25

1. Turn on the computer. If the computer cannot be turned on, go to Power system checkout on page 26, and check the power sources. If an error code is displayed, go to Symptom-to-FRU index on page 37 for error code descriptions and troubleshooting hints.

2. Insert the CD into the external optical drive.

3. Restart the computer.

4. When the ThinkPad logo is displayed, repeatedly press and release the F12 key. When the Boot Menu window opens, release the F12 key.

5. Use the arrow keys to select ATAPI CDx (x: 0, 1, ...) and then press Enter. The diagnostic program will be launched automatically.

6. Follow the instructions on the screen to use the diagnostic program.

Power system checkout To verify if a battery and ac power adapter are functional, do the following: 1. Turn off the computer. 2. Connect the ac power adapter. 3. Turn on the computer. If the computer can be turned on, it means that either the battery or the ac

power adapter is functional. 4. Insert a straightened paper clip into the emergency reset hole to reset the computer. If the computer is

still powered on, it means that the ac power adapter is functional. 5. Turn off the computer. 6. Disconnect the ac power adapter and turn on the computer. If the computer can be turned on, it

means the battery is functional.

If you suspect a power problem, see the appropriate one of the following power supply checkouts: Checking the ac power adapter on page 26 Checking the battery and operational charging on page 27 Checking the coin-cell battery on page 27

Checking the ac power adapter You are here because the computer fails only when the ac power adapter is used. If the system status indicator does not blink three times when an ac power source is connected, check

the power cord of the ac power adapter for correct continuity and installation. If the computer does not charge during operation, go to Checking the battery and operational charging

on page 27.

To check the ac power adapter, do the following:

1. Unplug the ac power adapter cable from the computer.

2. Measure the output voltage at the plug of the ac power adapter cable. See the following illustration:

Pin Voltage (V dc)

1 +20

2 0

3 Ground(20V) 1

3

2

Note: Output voltage of pin 2 of the ac power adapter might differ from the one you are servicing.

3. If the voltage is not correct, replace the ac power adapter.

4. If the voltage is acceptable, replace the system board.

26 Hardware Maintenance Manual

Note: Noise from the ac power adapter does not always indicate a defect.

Checking the battery and operational charging

Checking the battery

This system supports only batteries specially designed for this specific system and manufactured by Lenovo or an authorized builder. The system does not support unauthorized batteries or batteries designed for other systems. If an unauthorized battery or a battery designed for another systems is installed, the system will not charge.

Attention: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and provides no warranties for failures or damage arising out of their use.

Move your pointer to the battery-status icon in the Windows notification area to check the battery status. The battery-status icon displays the percentage of battery power remaining and how long you can use your computer before you must charge the battery.

Checking the operational charging

To check whether the battery charges properly during operation, do the following:

1. Discharge the battery until the remained battery power is less than 50%.

2. Perform operational charging. Click the battery status icon in the Windows notification area to display detailed battery information. If it indicates that the battery is not charging, replace the battery.

3. Check the battery status again. If the same error still exists, replace the system board.

Checking the coin-cell battery To check the coin-cell battery, do the following:

1. Disable the built-in battery. See Disabling the built-in battery on page 58.

2. Remove the coin-cell battery. See 1180 System board assembly on page 81.

3. Measure the voltage of the coin-cell battery. See the following illustration.

Wire Voltage (V dc)

Red +2.5 to +3.2

Black Ground

If the voltage is correct, replace the system board. If the voltage is not correct, replace the coin-cell battery. If the coin-cell battery discharges quickly after replacement, replace the system board.

Chapter 3. General checkout 27

28 Hardware Maintenance Manual

Chapter 4. Related service information

This chapter presents following information: Restoring the factory contents by using the product Recovery Disc Set on page 29 Using the Windows recovery programs on the Windows 8.1 operating system on page 30 Recovery overview for the Windows 10 operating system on page 32 Passwords on page 34 Power management on page 36 Symptom-to-FRU index on page 37

Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.com/support

Restoring the factory contents by using the product Recovery Disc Set When the main storage drive is replaced because of a failure, no product recovery program is on the new drive. In this case, the customer must use the Recovery Disc Set to recover the computer. Order the Recovery Disc Set and the drive at the same time so that the customer can restore the computer to the factory default settings by using the Recovery Disc Set after the new drive is installed. For information about which discs to order, go to: http://www.lenovo.com/serviceparts-lookup.

Depending on the model, the number of recovery discs included in the Recovery Disc Set differs. To restore the factory contents by using the product Recovery Disc Set, do the following:

Notes:

During the recovery process, all data on the drive will be deleted. If possible, copy any important data or personal files that you want to keep onto removable media or a network drive before you start the recovery process.

The recovery process takes one to two hours to complete. The length of time depends on the method you use. If you use product Recovery Disc Set, the recovery process takes about two hours.

1. Connect an external CD/DVD drive.

2. Make the CD/DVD drive the first startup device in the startup sequence using the following procedure:

a. Open the ThinkPad Setup program and select Startup Boot.

b. Select the CD/DVD drive as the 1st Boot Device.

3. Insert the bootable recovery disc into the CD/DVD drive.

4. Start the computer from the external CD/DVD drive.

5. When promoted, select your language and click Next.

6. Read the license and accept the terms and conditions. Then follow the instructions on the screen.

7. If the Recovery Disc Set contains a Supplemental Recovery Disc, insert it when prompted and click Yes.

Note: Not all Recovery Disc Sets come with a Supplemental Recovery Disc. If there is a Supplemental Recovery Disc, it will be clearly marked as such.

8. When all of the data has been copied from the last disc in the set and has been processed, remove the external CD/DVD drive and restart the computer. Follow the instructions on the screen to finish the recovery.

Note: The rest of the recovery process is fully automated and no action from you is required. The computer will restart into the Microsoft Windows desktop several times and you might experience periods when no activity is apparent on the screen for several minutes at a time. This is normal.

Copyright Lenovo 2015 29

9. When the recovery process completes, the Welcome to Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup.

10. After you have completed the Windows setup, you might want to restore the original startup sequence. Start the ThinkPad Setup program and then press F9 to restore the default settings. Press F10 to save changes and exit the ThinkPad Setup program.

Note: After restoring a drive to the factory default settings, you might need to reinstall some device drivers.

Using the Windows recovery programs on the Windows 8.1 operating system This section provides information about the recovery solutions for the Windows 8.1 operating system.

A Windows recovery image is preinstalled in the recovery partition on your computer. The Windows recovery image enables you to refresh your computer, or reset your computer to the factory default settings.

You can create recovery media as backups or replacement for the Windows recovery image. With the recovery media, you can troubleshoot and fix the problems on your computer even if you cannot start the Windows 8.1 operating system. It is recommended that you create recovery media as early as possible.

Refreshing the computer

If your computer does not perform well and the problem might be caused by a recently installed program, you can refresh your computer without losing your personal files or changing your settings.

Attention: If you refresh your computer, the programs that came with your computer and the programs that you installed from Windows Store will be reinstalled, but all other programs will be removed.

To refresh your computer, do the following:

1. Move your pointer to the top-right or bottom-right corner of the screen to display the charms. Click Settings Change PC settings Update and recovery Recovery.

2. In the Refresh your PC without affecting your files section, click Get started.

3. Follow the instructions on the screen to refresh your computer.

Resetting the computer to the factory default settings

If you want to recycle your computer or just start over, you can reset your computer to the factory default settings. Resetting the computer will reinstall the operating system, reinstall all the programs that came with your computer, and reset all the settings to the factory default settings.

Attention: If you reset the computer to the factory default settings, all your personal files and settings will be deleted. To avoid data loss, make a backup copy of all the data that you want to keep.

To reset your computer to the factory default settings, do the following:

1. Move your pointer to the top-right or bottom-right corner of the screen to display the charms. Click Settings Change PC settings Update and recovery Recovery.

2. In the Remove everything and reinstall Windows section, click Get started. Then click Next to confirm the operation.

3. Depending on your needs, do one of the following:

To perform a quick format, click Just remove my files to start the process. The process will take several minutes.

To perform a complete format, click Fully clean the drive to start the process. The process will take several hours.

30 Hardware Maintenance Manual

4. Follow the instructions on the screen to reset your computer to the factory default settings.

Using the advanced startup options

With the advanced startup options, you can change the firmware settings of the computer, change the startup settings of the Windows operating system, start the computer from an external device, or restore the Windows operating system from a system image.

To use the advanced startup options, do the following:

1. Move your pointer to the top-right or bottom-right corner of the screen to display the charms. Click Settings Change PC settings Update and recovery Recovery.

2. In the Advanced startup section, click Restart now Troubleshoot Advanced options.

3. Select a desired startup option, then follow the instructions on the screen.

Recovering your computer from the Windows recovery environment

The Windows recovery environment on your computer is capable of operating independently from the Windows 8.1 operating system. This enables you to recover or repair the operating system even if the Windows 8.1 operating system fails to start.

After two consecutive failed boot attempts, the Windows recovery environment starts automatically. Then you can choose repair and recovery options by following the instructions on the screen.

Note: Ensure that your computer is connected to ac power during the recovery process.

You can create recovery media as backups for the Windows recovery environment and the Windows recovery image. If you cannot start the computer, you can use recovery media to troubleshoot and fix the problems on your computer.

It is recommended that you create recovery media as early as possible. Once you create recovery media, keep them in a safe place and do not use them to store other data.

Creating recovery media

To create recovery media, you need a USB drive with at least 16 GB of storage. The required USB capacity depends on the size of the recovery image.

Attention: Creating recovery media will delete anything stored on the USB drive. To avoid data loss, make a backup copy of all the data that you want to keep.

To create recovery media, do the following:

Note: Ensure that your computer is connected to ac power.

1. Move your pointer to the top-right or bottom-right corner of the screen to display the charms, and click Search.

2. Type recovery in the Search field and click the Search button. Then click Create a recovery drive.

3. Click Yes in the User Account Control window to allow the Recovery Media Creator program to start.

4. Ensure that you select the Copy the recovery partition from the PC to the recovery drive. option. Then click Next.

Important: If you clear the Copy the recovery partition from the PC to the recovery drive. option, you will create recovery media without the recovery partition content. You still can start the computer from the recovery media, but you might be unable to recover your computer if the recovery partition on your computer is damaged.

5. Connect a proper USB drive then click Next.

Chapter 4. Related service information 31

6. Click Create in the Recovery Drive window. The creation of the recovery media starts.

7. When the creation of the recovery media finishes, do one of the following:

To keep the recovery partition on your computer, click Finish.

To delete the recovery partition on your computer, click Delete the recovery partition.

Attention: If you delete the recovery partition on your computer, do keep the recovery media in a safe place. The Windows recovery image will not be stored in your computer anymore, and you will need the recovery media to refresh or reset your computer.

8. Remove the USB drive. The recovery media are created successfully.

Using recovery media

If you cannot start your computer, or if you cannot start the Windows recovery image on your computer, use recovery media to recover your computer.

To use recovery media, do the following:

Note: Ensure that your computer is connected to ac power.

1. Turn on or restart the computer. Before the Windows operating system starts, repeatedly press the F12 key. The Boot Menu window opens.

2. Select the recovery drive as the boot device.

3. Select a preferred language and then select a preferred keyboard layout.

4. Click Troubleshoot to display the optional recovery solutions.

5. Select a corresponding recovery solution according to your situation. For example, select Reset your PC if you want to reset your computer to the factory default settings.

For more information about the recovery solutions provided by the Windows 8.1 operating system, go to: http://go.microsoft.com/fwlink/?LinkID=263800

Recovery overview for the Windows 10 operating system The Windows recovery programs enable you to reset your computer or use advanced startup options.

It is recommended that you create a recovery USB drive as early as possible. Store the recovery USB drive as a backup or replacement for the Windows recovery programs.

For more information, see Creating and using a recovery USB drive on page 33.

Resetting your computer If your computer does not perform well, you might consider resetting your computer. In the resetting process, you can choose to keep your files or remove them, and then reinstall the Windows operating system.

To reset your computer, do the following:

Note: The graphical user interface (GUI) items of the operating system might change without notice.

1. Open the Start menu and then click Settings. If Settings is not displayed, click All apps to display all programs, and then click Settings Update & security Recovery.

2. In the Reset this PC section, click Get started.

3. Follow the instructions on the screen to reset your computer.

32 Hardware Maintenance Manual

Using advanced startup options With advanced startup options, you can change the firmware settings of the computer, change the startup settings of the Windows operating system, start the computer from an external device, or restore the Windows operating system from a system image.

To use advanced startup options, do the following:

Note: The GUI items of the operating system might change without notice.

1. Open the Start menu and then click Settings. If Settings is not displayed, click All apps to display all programs, and then click Settings Update & security Recovery.

2. In the Advanced startup section, click Restart now Troubleshoot Advanced options.

3. Select a desired startup option, then follow the instructions on the screen.

Recovering your operating system if Windows 10 fails to start The Windows recovery environment on your computer is capable of operating independently from the Windows 10 operating system. This enables you to recover or repair the operating system even if the Windows 10 operating system fails to start.

After two consecutive failed boot attempts, the Windows recovery environment starts automatically. Then you can choose repair and recovery options by following the instructions on the screen.

Note: Ensure that your computer is connected to ac power during the recovery process.

Creating and using a recovery USB drive You can create a recovery USB drive as a backup for the Windows recovery programs. With the recovery USB drive, you can troubleshoot and fix the problems even if the preinstalled Windows recovery programs are damaged.

Creating a recovery USB drive

The USB drive that you use to create the recovery USB drive must be at least 16 GB of storage. The actual USB capacity that is required depends on the size of the recovery image.

Attention: The creation process deletes anything stored on the USB drive. To avoid data loss, make a backup copy of all the data that you want to keep.

To create a recovery USB drive, do the following:

Note: Ensure that your computer is connected to ac power during the following process.

1. Connect a proper USB drive (at least 16 GB of storage).

2. Type recovery in the search box on the taskbar. Then click Create a recovery drive.

3. Click Yes in the User Account Control window to allow the Recovery Media Creator program to start.

4. In the Recovery Drive window, follow the on-screen instructions to create a recovery USB drive.

Using the recovery USB drive

If you cannot start your computer, use the recovery USB drive to recover your computer.

To use a recovery USB drive, do the following:

Note: Ensure that your computer is connected to ac power.

1. Connect the recovery USB drive to the computer.

Chapter 4. Related service information 33

2. Turn on or restart the computer. Before the Windows operating system starts, repeatedly press the F12 key. The Boot Menu window opens.

3. Select the recovery USB drive as the boot device.

4. Select a preferred keyboard layout.

5. Click Troubleshoot to display the optional recovery solutions.

6. Select a corresponding recovery solution according to your situation. Then follow the instructions on the screen to complete the process.

Passwords As many as three passwords may be needed for any ThinkPad notebook computer: the power-on password, the hard disk password, and the supervisor password.

If any of these passwords has been set, a prompt for it will be displayed on the screen whenever the computer is turned on. The computer does not start until the password is entered.

Note: If only a supervisor password is set, the password prompt will not be displayed when the operating system is started.

Power-on password A power-on password protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be started. For instructions on how to remove the power-on password, see How to remove the power-on password on page 35.

Hard disk password There are two kinds of hard disk passwords: User hard disk password - for the user Master hard disk password - for the system administrator, who can use it to get access to the hard disk

even if the user has changed the user hard disk password

Note: There are two modes for the hard disk password: User only and Master + User. The Master + User mode requires two hard disk passwords; the system administrator enters both in the same operation. The system administrator then provides the user hard disk password to the system user.

Attention: If the user hard disk password has been forgotten, check whether a master hard disk password has been set. If it has, it can be used for access to the hard disk drive. If no master hard disk password is available, neither Lenovo nor Lenovo authorized service technicians provide any services to reset either the user or the master hard disk password, or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.

For how to remove the hard disk password, see How to remove the hard disk password on page 35.

Supervisor password A supervisor password protects the system information stored in the ThinkPad Setup. The user must enter the supervisor password in order to get access to the ThinkPad Setup and change the system configuration.

Attention: If the supervisor password has been forgotten and cannot be made available to the service technician, there is no service procedure to reset the password. The system board must be replaced for a scheduled fee.

34 Hardware Maintenance Manual

How to remove the power-on password To remove a power-on password, do the following:

If no supervisor password has been set, do the following to remove the power-on password:

1. Turn off the computer and disconnect ac power.

2. Disable the built-in battery. See Disabling the built-in battery on page 58.

3. Remove the removable battery. See 1010 Removable battery on page 59.

4. Remove the base cover assembly. See 1020 Base cover assembly on page 59.

5. Remove the coin-cell battery. See 1090 Coin-cell battery on page 71.

6. Reinstall the coin-cell battery. See 1090 Coin-cell battery on page 71.

7. Reinstall the base cover assembly.

8. Reinstall the removable battery.

9. Reconnect ac power.

10. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does not appear. The power-on password has been removed.

If a supervisor password has been set and is known to the service technician, do the following to remove the power-on password:

1. Turn on the computer.

2. When the ThinkPad logo is displayed, immediately press F1.

3. Type the supervisor password to enter the ThinkPad Setup program.

4. Select Security.

5. Select Password.

6. Select Power-On Password.

7. Type the current supervisor password in the Enter Current Password field. Then leave the Enter New Password field blank, and press Enter twice.

8. In the Changes have been saved window, press Enter.

9. Press F10 to save changes and exit the ThinkPad Setup program. The power-on password has been removed.

How to remove the hard disk password Attention: If User only mode is selected and the user hard disk password has been forgotten and cannot be made available to the service technician, neither Lenovo nor Lenovo authorized service technicians provide any services to reset the user hard disk passwords, or to recover data from the hard disk drive. To put the system back to operational status, the only Lenovo and Lenovo-authorized service solution would be to replace the hard disk drive or solid-state drive with a scheduled fee.

To remove a user hard disk password that has been forgotten, when the supervisor password and master hard disk password are known, do the following:

1. Turn on the computer.

2. When the ThinkPad logo comes up, immediately press F1 to enter the ThinkPad Setup program. When the power-on password icon is displayed on the screen, enter either the power-on password or the supervisor password.

3. When the user hard disk password icon is displayed on the screen, press F1. The master hard disk password icon is displayed.

4. Enter the master hard disk password to enter the ThinkPad Setup program.

5. Select Security.

6. Select Password.

Chapter 4. Related service information 35

7. Select Hard-disk x password, where x is the letter of the hard disk drive. A pop-up window opens.

8. Select Master hard disk password.

9. Type the current master hard disk password in the Enter Current Password field. Then leave the Enter New Password field blank, and press Enter twice.

10. Press F10 to save changes and exit the ThinkPad Setup program. The user hard disk password and the master hard disk password have been removed.

Power management To reduce power consumption, the computer has three power management modes: screen blank, sleep, and hibernation.

Screen blank mode (for the Windows 7 operating system only) If the time set on the Turn off monitor timer in the operating system expires, the LCD backlight turns off.

To put the computer into screen blank mode, do the following:

1. Right-click the battery gauge in the task bar.

2. Select Power off display.

To end screen blank mode and resume normal operation, press any key.

Sleep mode When the computer enters sleep mode, the following events occur in addition to what occurs in screen blank mode: The LCD is powered off. The internal storage drive (hard disk drive, solid-state drive, or hybrid drive) is powered off. The microprocessor stops.

To enter sleep mode, press Fn+4 or do the following:

For Windows 7: Open the Start menu, then click the arrow next to the Shut down button. Click Sleep from the menu displayed.

For Windows 8.1: Go to the Start screen by pressing the Windows key , click the power icon , then click Sleep.

For Windows 10: Open the Start menu, click Power, and then click Sleep.

In certain circumstances, the computer goes into sleep mode automatically:

After a period of inactivity specified in power plan settings

When the battery power is low

To resume the computer from sleep mode, press the power button.

Also, in either of the following events, the computer automatically returns from sleep mode and resumes operation:

The ring indicator (RI) is signaled by a serial device or a PC Card device.

The time set on the resume timer elapses.

Note: The computer does not accept any input immediately after it enters sleep mode. Wait a few seconds before taking any action to reenter operation mode.

36 Hardware Maintenance Manual

Hibernation mode In hibernation mode, the following occurs:

The system status, RAM, VRAM, and setup data are stored on the hard disk.

The system is powered off.

Note: If the computer enters the hibernation mode while it is docked to the docking station, do not undock it before resuming normal operation. If you do undock it and then try to resume normal operation, you will get an error message, and you will have to restart the system.

If you have defined one of the following actions as the event that causes the system to go into hibernation mode, perform that action. Closing the lid. Pressing the power button.

Also, the computer goes into hibernation mode automatically after a period of inactivity specified in power plan settings.

When the power is turned on, the computer returns from hibernation mode and resumes operation. The hibernation file in the boot record on the hard disk drive is read, and system status is restored from the hard disk drive.

Symptom-to-FRU index This section contains following information: Numeric error codes on page 38 Error messages on page 39 Beep symptoms on page 39 No-beep symptoms on page 39 LCD-related symptoms on page 40 Intermittent problems on page 40 Undetermined problems on page 40

The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.

Note: Do the FRU replacement or other actions in the sequence shown in the column headed FRU or action, in sequence. If replacing a FRU does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU.

This index can also help you determine, during regular servicing, what FRUs are likely to need to be replaced next.

A numeric error is displayed for each error detected in POST or system operation. In the displays, n can be any number.

If no numeric code is displayed, check the narrative descriptions of symptoms. If the symptom is not described there, go to Intermittent problems on page 40.

Note: For a device not supported by diagnostic codes in the ThinkPad notebook computers, see the manual for that device.

Chapter 4. Related service information 37

Numeric error codes Table 1. Numeric error codes

Symptom or error FRU or action, in sequence

0177 Bad SVP data, stop POST taskThe checksum of the supervisor password in the EEPROM is not correct.

System board

0183 Bad CRC of Security Settings in EFI Variable. Enter the ThinkPad Setup program.

1. Run the ThinkPad Setup program, and then save current setting by pressing F10.

2. System board

0187 EAIA data access errorThe access to EEPROM is failed.

System board

0188 Invalid RFID Serialization Information Area.

System board

0189 Invalid RFID configuration information areaThe EEPROM checksum is not correct.

System board

0190 Critical low-battery error

1. Charge the battery. 2. Battery

0191 System SecurityInvalid Remote Change requested.

1. Run the ThinkPad Setup program, and then save current setting by pressing F10.

2. System board

0199 System Security Security password retry count exceeded.

1. Run the ThinkPad Setup program, and then save the current setting by pressing F10.

2. System board

0270 Real Time Clock Error.

System Real Time Clock is not functional. Have the computer serviced.

0271 Check Date and Time settings.

Neither the date nor the time is set in the computer. Enter ThinkPad Setup and set the date and time.

1802 Unauthorized network card is plugged inTurn off and remove the network card.

1. Remove wireless network card. 2. System board

1820 More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system.

Remove all but the reader that you set up for the authentication.

2100 Detection error on HDD0 (Main HDD)

1. Reseat the hard disk drive. 2. Main hard disk drive 3. System board

2101 Detection error on SSD1 (M.2)

The M.2 SSD device is not working. Have the M.2 SSD device serviced.

2102 Detection error on SSD2 (M.2)

The M.2 SSD device is not working. Have the M.2 SSD device serviced.

2110 Read error on HDD0 (Main HDD)

1. Reseat the hard disk drive. 2. Main hard disk drive 3. System board

2111 Read error on SSD1 (M.2)

The M.2 SSD device is not working. Have the M.2 SSD device serviced.

2112 Read error on SSD2 (M.2)

The M.2 SSD device is not working. Have the M.2 SSD device serviced.

38 Hardware Maintenance Manual

Table 1. Numeric error codes (continued)

Symptom or error FRU or action, in sequence

2200 Machine Type and Serial Number are invalid.

System board

2201 Machine UUID is invalid

System board

Error messages Table 2. Error messages

Symptom or error FRU or action, in sequence

Fan error 1. Fan 2. Thermal grease 3. System board

Thermal sensing error System board

Beep symptoms Table 3. Beep symptoms

Symptom or error FRU or action, in sequence

One short beep, pause, three short beeps, pause, three more short beeps, pause, and one short beep (1-3-3-1 beeps)

Memory problem

One long and two short beeps Video problem

Three short beeps, pause, one short beep, pause, one short beep, pause, and three more short beeps (3-1-1-3 beeps)

PCI resource problem

Four cycles of four short beeps TCG*-compliant functionality-related problem

Five short beeps System board

Five short beeps, pause, five more short beeps, and pause

TCG*-compliant functionality-related problem

No-beep symptoms Table 4. No-beep symptoms

Symptom or error FRU or action, in sequence

No beep, system-status indicator on, LCD blank, and no POST.

1. Ensure that every connector is connected tightly and correctly.

2. System board

No beep, system-status indicator on, and LCD blank during POST.

System board

The power-on password prompt appears. A power-on password or a supervisor password is set. Type the password and press Enter.

The hard-disk password prompt appears. A hard-disk password is set. Type the password and press Enter.

Chapter 4. Related service information 39

LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns.If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced.

Notes:

This policy applies to all ThinkPad notebooks purchased on 1 January, 2008 or later.

Lenovo will not provide warranty replacement if the LCD is within specifications because we cannot guarantee that any replacement LCD will have zero pixel defects.

One pixel consists of R, G, B sub-pixels.

Table 5. LCD-related symptoms

Symptom or error FRU or action, in sequence

No beep, power-on indicator on, and a blank LCD during POST.

System board

LCD backlight not working. LCD too dark. LCD brightness cannot be adjusted. LCD contrast cannot be adjusted.

1. Reseat the LCD connectors. 2. LCD assembly 3. System board

LCD screen unreadable. Characters missing pixels. Screen abnormal. Wrong color displayed.

1. See important note for LCD-related symptoms. 2. Reseat all LCD connectors. 3. LCD assembly 4. System board

Horizontal or vertical lines displayed on LCD. LCD assembly

Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs.

When analyzing an intermittent problem, do the following:

1. Run the diagnostic test for the system board in loop mode at least 10 times.

2. If no error is detected, do not replace any FRUs.

3. If any error is detected, replace the FRU shown by the FRU code. Rerun the test to verify that no more errors exist.

Undetermined problems If the diagnostic tests did not identify the adapter or device that has failed, if wrong devices are installed, or if the system simply is not operating, follow these procedures to isolate the failing FRU (do not isolate FRUs that have no defects).

Verify that all attached devices are supported by the computer.

Verify that the power supply being used at the time of the failure is operating correctly. See Power system checkout on page 26. 1. Turn off the computer. 2. Visually check each FRU for damage. Replace any damaged FRU. 3. Remove or disconnect all of the following devices:

40 Hardware Maintenance Manual

a. Non-ThinkPad devices b. Printer, mouse, and other external devices c. External diskette drive or optical drive d. Wireless cards

4. Turn on the computer. 5. Determine whether the problem has been solved. 6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. 7. If the problem remains, replace the following FRUs one at a time (do not replace a nondefective FRU):

a. System board b. LCD assembly

Chapter 4. Related service information 41

42 Hardware Maintenance Manual

Chapter 5. Locations

This chapter introduces the locations of the hardware components on your computer.

Locating computer controls, connectors, and indicators This topic introduces the locations of the computer controls, connectors, and indicators.

Front view

1 2

2

45678

3

9

10

11

12

1 Camera (available on some models) 2 Microphones (available on some models)

3 Power button with system-status indicator 1 4 Security-lock slot

5 Fan louvers 6 Mini DisplayPort connector

7 USB 3.0 connector 8 Always On USB 3.0 connector

9 Fingerprint reader (available on some models) 10 Trackpad

11 TrackPoint buttons 12 TrackPoint pointing stick

1: The indicator in the ThinkPad logo and the indicator in the center of the power button show the system status of the computer.

Blinks for three times: The computer is initially connected to power. On: The computer is on (in normal mode). Blinks fast: The computer is entering sleep or hibernation mode. Blinks slowly: The computer is in sleep mode. Off: The computer is off or in hibernation mode.

Copyright Lenovo 2015 43

Left-side view 8

1 2

3 4

5 6

7

1 Smart-card-reader slot (available on some models) 2 Ethernet connector

3 Media-card-reader slot 4 Audio connector

5 VGA connector 6 USB 3.0 connector

7 Power connector 8 System-status indicator 1

1: The indicator in the ThinkPad logo and the indicator in the center of the power button show the system status of the computer.

Blinks for three times: The computer is initially connected to power. On: The computer is on (in normal mode). Blinks fast: The computer is entering sleep or hibernation mode. Blinks slowly: The computer is in sleep mode. Off: The computer is off or in hibernation mode.

Bottom view 1

2

3

4

5 3

4

1 Removable battery 2 Docking station connector

3 Keyboard drainage holes 4 Speakers

5 Emergency-reset hole

44 Hardware Maintenance Manual

Locating FRUs and CRUs This topic introduces the following service parts: Major FRUs on page 46 LCD FRUs on page 47 Miscellaneous parts and other FRUs on page 50

Notes: Each FRU is available for all types or models, unless otherwise specified. CRU statement for customers:

You can resolve some problems with your product with a replacement part you can install yourself, called a Customer Replaceable Unit or CRU. Some CRUs are designated as self-service CRUs and others are designated as optional-service CRUs. Installation of self-service CRUs is your responsibility. For optional-service CRUs, you can either install the CRU yourself or you can request that a Service Provider install the CRU according to the warranty service for your product. If you intend on installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request. You can find a list of CRUs for your product in this Hardware Maintenance Manual. An electronic version of this manual can be found at http://www.lenovo.com/support. Follow the on-screen instructions to find the manual for your product. You might be required to return the defective part that is replaced by the CRU. When return is required: (1) return instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you might be charged for the replacement CRU if Lenovo does not receive the defective CRU within thirty (30) days of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.

ThinkPad computers contain the following types of CRUs: Self-service CRUs: These CRUs unplug or are held by no more than two screws. Examples of these types

of CRUs include the ac power adapter, power cord, and hard disk drive. Other self-service CRUs depending on product design might include the memory module, wireless card, keyboard, and palm rest with fingerprint reader and touch pad.

Optional-service CRUs: These CRUs are isolated parts within the computer that are concealed by an access panel that is typically secured by more than two screws. Once the access panel is removed, the specific CRU is visible.

Chapter 5. Locations 45

Major FRUs

16

18

17

26

25

21

22

23

24

19

20

1

2

4

5

6

8

9

10

11

12

13

14

15

7

3

No. Descriptions Self-service CRU Optional-service CRU

1 LCD unit (see LCD FRUs on page 47)

2 Keyboard bezel assembly No No

3 System board No No

4 Power button board No No

5 Thermal fan No No

46 Hardware Maintenance Manual

No. Descriptions Self-service CRU Optional-service CRU

6 Memory module Yes No

7 Fingerprint reader * No No

8 Fingerprint reader bracket * No No

9 Internal storage drive (hard disk drive, solid-state drive, or hybrid drive)

Yes No

10 Hard disk drive cable Yes No

11 Hard disk drive bracket Yes No

12 Storage-drive stabilizer bar No Yes

13 Speaker assembly No No

14 Removable battery Yes No

15 Base cover assembly No No

16 Smart card reader or dummy smart card reader (depending on the model)

No No

17 Built-in battery or battery bracket (depending on the model) No No

18 Coin-cell battery Yes No

19 M.2 solid-state drive * No No

20 Wireless WAN card * Yes No

21 Wireless LAN card Yes No

22 dc-in bracket No Yes

23 dc-in cable No Yes

24 Board for Trackpad and TrackPoint buttons No No

25 Keyboard No Yes

26 TrackPoint cap No Yes

Note: Depending on the model, the items marked with an asterisk (*) might not be available on your computer.

LCD FRUs For models without touch function:

Chapter 5. Locations 47

9

1

2

3

6

5

4

7

8

No. Descriptions Self-service CRU Optional-service CRU

1 LCD bezel assembly No No

2 Camera/microphone card No No

3 LCD panel without touch function No No

48 Hardware Maintenance Manual

No. Descriptions Self-service CRU Optional-service CRU

4 Antenna kit or dummy antenna kit No No

5 LED cable assembly No No

6 Hinge brackets No No

7 Hinges No No

8 LCD rear cover assembly No No

For models with touch function:

8

1

2

6

4

5

3

7

Chapter 5. Locations 49

No. Descriptions Self-service CRU

Optional-service CRU

1 LCD panel assembly with touch function No No

2 Camera/microphone card No No

3 Touch sensor card No No

4 Antenna kit or dummy antenna kit No No

5 LED cable assembly No No

6 Hinges No No

7 LCD rear cover assembly No No

8 LCD front sheet bezel No No

Miscellaneous parts and other FRUs

Miscellaneous part

FRU descriptions Self-service CRU Optional-service CRU

Screw kit

M2*L3.5, silver, thin head (100)

M2*L3, black, thin head (30)

M2*L2.5, big head (30)

M2*L3, big head (30)

M2*L2.5 + 3.1 (30)

M2*L6 (30)

M2.5*L7 (30)

M2*L2.5, black (30)

M2.5*L2.5, big head (30)

M2.5*L4, silver (30)

M2*L2, black, P=0.25 (30)

Spec (1)

No No

Base cover assembly miscellaneous kit

Battery latch L (1)

Battery latch R (1)

Battery knob L (1)

Battery knob R (1)

Front rubber foot (1)

Rear rubber foot (1)

Base cover ESD sponge (1)

Battery latch spring (1)

Spec (1)

No No

50 Hardware Maintenance Manual

Other FRUs

FRU descriptions Self-service CRU

Optional-service CRU

ac power adapter Yes No

Power cord Yes No

Looking up FRU information For detailed FRU information, including part numbers, descriptions, and substitution part numbers, go to http://www.lenovo.com/serviceparts-lookup.

Chapter 5. Locations 51

52 Hardware Maintenance Manual

Chapter 6. FRU replacement notices

This chapter presents notices related to removing and replacing parts. Read this chapter carefully before replacing any FRU.

CRU statement for customers: You can resolve some problems with your product with a replacement part you can install yourself, called a Customer Replaceable Unit or CRU. Some CRUs are designated as self-service CRUs and others are designated as optional-service CRUs. Installation of self-service CRUs is your responsibility. For optional-service CRUs, you can either install the CRU yourself or you can request that a Service Provider install the CRU according to the warranty service for your product. If you intend on installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request. You can find a list of CRUs for your product in this Hardware Maintenance Manual. An electronic version of this manual can be found at http://www.lenovo.com/support. Click Guides & Manuals and then follow the on-screen instructions to find the manual for your product. You might be required to return the defective part that is replaced by the CRU. When return is required: (1) return instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you might be charged for the replacement CRU if Lenovo does not receive the defective CRU within thirty (30) days of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.

Common service tools Below is the list of common service tools that you might need while servicing the computer. Screwdriver kit 1/4" drive spinner handle 1/4" Sq. to 1/4" hex torx adapter TR7-TR-10 tamper resistant torx bits Removal tool antenna RF connector USB 2.0 CD-RW/DVD-ROM combo drive II USB cable USB Maintenance Key USB floppy diskette drive for maintenance diskette USB floppy diskette drive tool kit Test card for integrated Smart Card LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later

Note: Download the file from the following Web site: http://www.lenovo.com/support

Screw notices Loose screws can cause a reliability problem. In the ThinkPad notebook computer, this problem is addressed with special nylon-coated screws that have the following characteristics: They maintain tight connections. They do not easily come loose, even with shock or vibration. They are harder to tighten.

Do the following when you service this machine: Keep the screw kit in your tool bag. For the part number of the screw kit, go to

http://www.lenovo.com/serviceparts-lookup. It is recommended to use new screws.

Copyright Lenovo 2015 53

It is recommended to use each screw only once.

Tighten screws as follows:

Plastic to plastic Turn an additional 90 degrees after the screw head touches the surface of the plastic part.

90 degrees more

(Cross-section)

Logic card to plastic Turn an additional 180 degrees after the screw head touches the surface of the logic card.

180 degrees more

(Cross-section)

Notes:

Ensure that you use the correct screw. It is recommended to use new screws for replacements. If you have a torque screwdriver, tighten all screws firmly to the torque specified in the screw information table for each step.

Ensure that torque screwdrivers are calibrated correctly following country specifications.

Retaining serial numbers This section includes the following descriptions: Restoring the serial number of the system unit on page 54 Retaining the UUID on page 55 Reading or writing the ECA information on page 56

Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.

If you replace the system board, you must restore the serial number of the system unit to its original value.

The serial number of the system unit is written on the label attached to the bottom of the computer.

If you cannot find the serial number of the system unit on the bottom of the computer, try the following method to get the number:

Note: Before you perform the operation, ensure that the UEFI/Legacy setting within the Startup menu in the ThinkPad Setup program is set to UEFI Only.

1. Connect a USB memory key to the computer.

54 Hardware Maintenance Manual

2. Go to http://www.lenovo.com/maintenanceutilities and follow the instructions on the screen to create a Maintenance Key.

Note: Only an authorized Lenovo service technician can access the above Web site.

3. Restart the computer.

4. When the logo is displayed, press Esc. The ThinkPad Config Information Update Utility interface is displayed.

5. Type 1 under Enter the action desired, then press Enter. The ThinkPad Serial Number Update Utility for Asset ID screen is displayed.

6. Type 2 under Enter the action desired, then press Enter. The serial number of each device in your computer is displayed; the serial number of the system unit is listed as follows: 20- Serial number

7. Record the serial number of the system unit.

After you replace the system board, do the following to restore the serial number of the system unit:

1. Connect the Maintenance Key to the computer.

2. When the logo is displayed, press Esc. The ThinkPad Config Information Update Utility interface is displayed.

3. Type 1 under Enter the action desired, then press Enter. The ThinkPad Serial Number Update Utility for Asset ID screen is displayed.

4. Type 1 under Enter the action desired, then press Enter. Then follow the instructions on the screen to restore the serial number of the system unit.

Retaining the UUID The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at production and stored in the EEPROM of your system board.

The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number.

When you replace the system board, perform the following steps to create a new UUID for the system board if the system board does not have a UUID:

Note: Before you perform the operation, ensure that the UEFI/Legacy setting within the Startup menu in the ThinkPad Setup program is set to UEFI Only.

1. Connect a USB memory key to the computer.

2. Go to http://www.lenovo.com/maintenanceutilities and follow the instructions on the screen to create a Maintenance Key.

Note: Only an authorized Lenovo service technician can access the above Web site.

3. Restart the computer.

4. When the logo screen is displayed, press Esc. The ThinkPad Config Information Update Utility interface is displayed.

5. Type 2 under Enter the action desired, then press Enter. The Auto UUID generation utility interface is displayed.

6. Type y under Change UUID. OK? [Y/N], then press Enter. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.

Chapter 6. FRU replacement notices 55

Reading or writing the ECA information Information on Engineering Change Announcements (ECA) is stored in the EEPROM of the system board. The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application.

To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the USB Maintenance Key.

1. Insert the Maintenance Key and restart the computer.

2. From the main menu, select 6. Set ECA Information.

3. To read the ECA information, select 2. Read ECA/rework number from EEPROM and follow the instructions on the screen.

4. To read the box build date, select 5. Read box build date from EEPROM, and follow the instruction on the screen.

After an ECA has been applied to the machine, the EEPROM must be updated to reflect the ECA's application. Use the Maintenance Key to update the EEPROM.

Note: Only the ECA number is stored in the EEPROM. The machine type of the ECA is assumed to be the same as the machine type of the machine that had the ECA applied to it.

1. Insert the Maintenance Key and restart the computer.

2. From the main menu, select 6. Set ECA Information.

3. To write the ECA information, select 1. Write ECA/rework number from EEPROM, and follow the instructions on the screen.

4. To write the box build date, select 4. Write box build date from EEPROM, and follow the instruction on the screen.

If the system board is being replaced, try to read the ECA information from the old system board and transfer the information to the new system. If the system board is inoperable, this will not be possible.

56 Hardware Maintenance Manual

Chapter 7. Removing or replacing a FRU

This chapter provides instructions on how to remove or replace a FRU.

CRU statement for customers:

You can resolve some problems with your product with a replacement part you can install yourself, called a Customer Replaceable Unit or CRU. Some CRUs are designated as self-service CRUs and others are designated as optional-service CRUs. Installation of self-service CRUs is your responsibility. For optional-service CRUs, you can either install the CRU yourself or you can request that a Service Provider install the CRU according to the warranty service for your product. If you intend on installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request. You can find a list of CRUs for your product in this Hardware Maintenance Manual. An electronic version of this manual is available for downloading at http://www.lenovo.com/support. You might be required to return the defective CRU. When return is required: (1) return instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you might be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.

General guidelines When removing or replacing a FRU, be sure to observe the following general guidelines:

1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts.

2. Before replacing any FRU, review Chapter 6 FRU replacement notices on page 53.

3. Begin by removing any FRUs that have to be removed before replacing the failing FRU. Any such FRUs are listed at the beginning of each FRU replacement section. Remove them in the order in which they are listed.

4. Follow the correct sequence in the steps for removing a FRU, as given in the drawings by the numbers in square callouts.

5. When turning a screw, turn it in the direction as given by the arrow in the drawing.

6. When removing a FRU, move it in the direction as given by the arrow in the drawing.

7. To put the new FRU in place, reverse the removal procedure and follow any notes that pertain to replacement.

8. When replacing a FRU, use the correct screws as shown in the replacement procedures.

DANGER

Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, disconnect any interconnecting cables, and then disable the built-in battery.

Attention: After replacing a FRU, do not turn on the computer until you have made sure that all screws, springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.

Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge (ESD). Before touching it, establish personal grounding by touching a ground point with one hand or by using an ESD strap.

Copyright Lenovo 2015 57

Before servicing the computer Carefully read this topic before servicing the computer.

Disabling the built-in battery Before replacing any FRU, ensure that you have disabled the built-in battery by doing the following:

1. Turn off your computer and disconnect the ac power adapter and all cables from the computer.

2. Turn on your computer. When the ThinkPad logo is displayed, immediately press F1 to enter ThinkPad Setup.

3. Select Config Power. The Power submenu is displayed.

4. Select Disable built-in battery and press Enter.

5. Select Yes in the Setup Confirmation window. The built-in battery is disabled and the computer turns off automatically. Wait three to five minutes to let the computer cool.

Removing the micro SIM card For access, remove this FRU: 1010 Removable battery on page 59

If the computer has a micro SIM card installed, you also must remove the micro SIM card before you start the servicing.

1

2

After you finish the servicing, ensure that you install the micro SIM card (if available) into the micro SIM card slot.

Removing a major FRU This section provides instructions on how to remove a major FRU.

58 Hardware Maintenance Manual

1010 Removable battery

Important notice for replacing a removable battery

Attention: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and provides no warranties for failures or damage arising out of their use.

The Lenovo Solution Center program provides an automatic battery diagnostic test that determines if the battery pack is defective. A battery pack FRU should not be replaced unless this diagnostic test shows that the battery is defective. The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue.

If the Lenovo Solution Center program is not installed on the computer, the customer should download and install the program to diagnose the battery pack, before getting a non-physically damaged battery pack replaced. Note that the replacement of a physically damaged battery pack is not covered by the warranty.

Removal steps of the removable battery

DANGER

Use only the authorized battery specified for your computer. Any other battery could ignite or explode.

1

1

2

2

3

1020 Base cover assembly For access, remove this FRU: 1010 Removable battery on page 59

Chapter 7. Removing or replacing a FRU 59

Removal steps of the base cover assembly

1

2

3

3

3

3

3

3

3

3 3

3

3

3

4

60 Hardware Maintenance Manual

Applying labels to the base cover:

The new base cover assembly is shipped with a kit containing labels of several kinds. Apply those labels when you replace the base cover assembly. For the labels that are not shipped with the new base cover assembly, peel them from the old base cover assembly, and adhere them to the new one.

The following illustration shows the location of each label.

1 2 3 4 5 6 7

8

9

11

12

14

16

15

17

18

19

20

21

22

13

10

1 System barcode label 2 System label

3 FCC label 4 WWAN label (for Taiwan and Korea)

5 Information label 6 GEO label

7 Certificate of Authenticity label (for Windows 7) 8 China GEO label

9 CECP label (for China) 10 WWAN IMEI label

11 Genuine Microsoft label (for Windows 8.1) 12 Asset tag

13 Korea KC Safety label (for Korea) 14 Mexico Energy label (for Mexico)

15 SIRIM label (for Malaysia) 16 Postel label (for Malaysia)

17 ICASA label (for South Africa) 18 Brazil WWAN label (for Brazil)

19 ISRAEL label (for Israel) 20 Postel label (for Indonesia)

21 Indonesia Rating label (for Indonesia) 22 INDIA BIS label (for India)

1030 Keyboard For access, remove this FRU: 1010 Removable battery on page 59

Chapter 7. Removing or replacing a FRU 61

Removal steps of the keyboard

To reveal the screw heads beneath the keyboard frame, slide the keyboard frame forward by 2.5 mm (0.1 inch) with the flat end of the keyboard multi-tool.

1

Loosen the screws that secure the keyboard with the cross end of the keyboard multi-tool.

2

62 Hardware Maintenance Manual

Pivot the keyboard slightly upward until you can see the connectors on the bottom side of the keyboard 3 . Then turn over the keyboard 4 .

4

3

Gently put the keyboard on the palm rest and detach the connectors. Then remove the keyboard.

5

6 7

8

Installing the new keyboard

Attach the connectors and then turn over the keyboard.

4

3 2

1

5

Chapter 7. Removing or replacing a FRU 63

Insert the keyboard into the space under the frame of the keyboard bezel as shown. Ensure that the front edge of the keyboard (the edge that is close to the display) is under the frame of the keyboard bezel.

6

6

Reveal the screw heads by sliding the keyboard frame forward with the flat end of the keyboard multi-tool. Ensure that the screw heads are exposed completely.

7

64 Hardware Maintenance Manual

Tighten the screws with the cross end of the keyboard multi-tool to secure the keyboard in place.

8

Slide the keyboard frame backward by 2.5 mm (0.1 inch) with the flat end of the keyboard multi-tool. Hide the latches of the keyboard frame under the keyboard bezel by pushing the latches with your finger as shown.

9

9

Chapter 7. Removing or replacing a FRU 65

Adjust the keyboard frame in place with the flat end of the keyboard multi-tool to ensure that all the latches are secured under the keyboard bezel.

10

1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive bracket For access, remove this FRU: 1010 Removable battery on page 59 1020 Base cover assembly on page 59

Attention:

Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data.

Before removing the drive, have the user make a backup copy of all the information on it if possible.

Never remove the drive while the system is operating or in suspend mode.

Removal steps of the storage-drive stabilizer bar

1

1 2

Step Screw (quantity) Color Torque

1 M2 L3.5 mm, flat-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgf-cm)

66 Hardware Maintenance Manual

Removal steps of the internal storage drive

4

3

Step Screw (quantity) Color Torque

4 M2 L3.5 mm, flat-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgf-cm)

5

When installing: Ensure that the internal storage drive is firmly attached.

Removal steps of the hard disk drive cable and hard disk drive bracket

6

Chapter 7. Removing or replacing a FRU 67

7

7

7

7

1050 Memory module For access, remove this FRU: 1010 Removable battery on page 59 1020 Base cover assembly on page 59

Removal steps of the memory module

2

1 1

1060 Wireless LAN card Note: This information is only for the user-replaceable modules.

For access, remove this FRU: 1010 Removable battery on page 59 1020 Base cover assembly on page 59

68 Hardware Maintenance Manual

Removal steps of the wireless LAN card

1

2

Step Screw (quantity) Color Torque

1 M2 L3.5 mm, flat-head, nylon-coated (1) Bronze 0.181 Nm (1.85 kgf-cm)

3

When installing: Plug the gray cable into the main connector and the black cable into the auxiliary connector.

1070 Wireless WAN card Note: This information is only for the user-replaceable modules.

For access, remove this FRU: 1010 Removable battery on page 59 1020 Base cover assembly on page 59

Chapter 7. Removing or replacing a FRU 69

Removal steps of the wireless WAN card

1

2

2

Step Screw (quantity) Color Torque

1 M2 L3.5 mm, flat-head, nylon-coated (1) Bronze 0.181 Nm (1.85 kgf-cm)

3

When installing: Plug the orange cable into the main connector and the blue cable into the auxiliary connector.

1080 M.2 solid-state drive For access, remove this FRU: 1010 Removable battery on page 59 1020 Base cover assembly on page 59

70 Hardware Maintenance Manual

Removal steps of the M.2 solid-state drive

1

Step Screw (quantity) Color Torque

1 M2 L3.5 mm, flat-head, nylon-coated (1) Bronze 0.181 Nm (1.85 kgf-cm)

1090 Coin-cell battery For access, remove this FRU: 1010 Removable battery on page 59 1020 Base cover assembly on page 59

Chapter 7. Removing or replacing a FRU 71

Removal steps of the coin-cell battery

1

2

When installing: Ensure that the connector is attached firmly.

1110 dc-in bracket and dc-in cable assembly For access, remove these FRUs: 1010 Removable battery on page 59 1020 Base cover assembly on page 59

Removal steps of the dc-in bracket and dc-in cable assembly

1

1 2

72 Hardware Maintenance Manual

Step Screw (quantity) Color Torque

1 M2 L3.5 mm, flat-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgf-cm)

4

3

When installing: Ensure that the connector is attached firmly.

Attention: Do not route the dc-in cable on the hinge. Otherwise, the dc-in cable might get damaged when the base cover assembly is installed.

1120 Built-in battery or dummy battery Important notices for replacing a battery

Attention: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and provides no warranties for failures or damage arising out of their use.

Chapter 7. Removing or replacing a FRU 73

The Lenovo Solution Center program provides an automatic battery diagnostic test that determines if the battery is defective. A battery FRU should not be replaced unless this diagnostic test shows that the battery is defective. The only exception to this is if the battery is physically damaged or a customer is reporting a possible safety issue.

If the Lenovo Solution Center program is not installed on the computer, the customer should download and install the program to diagnose the battery, before getting a non-physically damaged battery replaced. Note that the replacement of a physically damaged battery is not covered by the warranty.

For access, remove this FRU: 1010 Removable battery on page 59 1020 Base cover assembly on page 59

Removal steps of the built-in battery or dummy built-in battery

DANGER

Use only the authorized battery specified for your computer. Any other battery could ignite or explode.

Note: If your computer does not come with a built-in battery, a dummy built-in battery is installed instead. To remove the dummy built-in battery, you do not have to perform step 1 in the following illustration.

1 2

2

2

2

2

Step Screw (quantity) Color Torque

2 M2 L3.5 mm, flat-head, nylon-coated (5) Silver 0.181 Nm (1.85 kgf-cm)

3

74 Hardware Maintenance Manual

1130 Thermal fan For access, remove this FRU: 1010 Removable battery on page 59 1020 Base cover assembly on page 59

Removal steps of the thermal fan

1

2

3

4

When installing: Ensure that the fan connectors are attached firmly.

Chapter 7. Removing or replacing a FRU 75

Loosen the screws 5 in ascending alphabetical order as illustrated.

Note: The thermal fan on your computer might look differently. For some models, you might not have to perform steps 5f and 5e in the following illustration.

5c 5f

5e

5a

5d

5b

6

7

76 Hardware Maintenance Manual

When installing: Do not touch the areas marked a and b in the following illustrations.

a

b

a

1140 Speaker assembly For access, remove this FRU: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1120 Built-in battery or dummy battery on page 73

Removal steps of the speaker assembly

2

2

2

1

Step Screw (quantity) Color Torque

2 M2 L2.5 mm, flat-head shoulder, nylon-coated (3) Black 0.181 Nm (1.85 kgf-cm)

When installing: Ensure that the connector is attached firmly.

Chapter 7. Removing or replacing a FRU 77

3

3

Cable routing: When you install the speaker assembly, route the cables as shown in the following illustration.

1150 Smart card assembly or dummy smart card Depending on the model, your computer might have a smart card or a dummy smart card installed.

For access, remove these FRUs: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1120 Built-in battery or dummy battery on page 73 1140 Speaker assembly on page 77

Removal steps of the smart card assembly

2

1

33 3

3

3

When installing: Ensure that the connector is attached firmly.

78 Hardware Maintenance Manual

Step Screw (quantity) Color Torque

3 M2 L3 mm, flat-head, nylon-coated (5) Black 0.181 Nm (1.85 kgf-cm)

4

Removal steps of the dummy smart card

1

2

Step Screw (quantity) Color Torque

1 M2 L3 mm, flat-head, nylon-coated (1) Black 0.181 Nm (1.85 kgf-cm)

1160 Fingerprint reader assembly For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66

Chapter 7. Removing or replacing a FRU 79

Removal steps of the fingerprint reader assembly

2

1

3 3

Step Screw (quantity) Color Torque

3 M2 L3 mm, flat-head, nylon-coated (2) Black 0.181 Nm (1.85 kgf-cm)

When installing: Ensure that the connector is attached firmly.

4

5

1170 Board for the trackpad and TrackPoint buttons For access, remove this FRU: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1120 Built-in battery or dummy battery on page 73

80 Hardware Maintenance Manual

Removal steps of the board for the trackpad and TrackPoint buttons

2

1

33

3 3

Step Screw (quantity) Color Torque

3 M2 L2 mm, flat-head shoulder, nylon-coated (4) Black 0.181 Nm (1.85 kgf-cm)

When installing: Ensure that the connector is attached firmly.

4

5

1180 System board assembly Important notices for handling the system board

When handling the system board, read the following:

Chapter 7. Removing or replacing a FRU 81

The system board has an accelerometer, which can be broken when several thousands of G-forces are applied.

Note: Dropping a system board from a height of as little as six inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6000 G's of shock.

Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.

Avoid rough handling of any kind.

At every point in the process, be sure not to drop or stack the system board.

If you put a system board down, be sure to put it only on a padded surface such as an ESD mat or a corrugated conductive material.

For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68 1070 Wireless WAN card on page 69 1130 Thermal fan on page 75 1140 Speaker assembly on page 77

Attention: The microprocessor a and GPU b soldered on the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling.

a b

82 Hardware Maintenance Manual

Removal steps of the system board assembly

6

2

1

5

4 3

8

7

10

9

11

11

11

11

1111

12

When installing: Ensure that the connectors are attached firmly.

Step Screw (quantity) Color Torque

11 M2 L3.5 mm, flat-head, nylon-coated (6) Silver 0.181 Nm (1.85 kgf-cm)

1190 LCD unit For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59

Chapter 7. Removing or replacing a FRU 83

Removal steps of the LCD unit

11

4

5

2

1

3

3

3

6 6 6 6

6

6

When installing: When you route the cables, ensure that they are not subject to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.

7 7

7 7

84 Hardware Maintenance Manual

Step Screw (quantity) Color Torque

7 M2.5 L3.5 mm, flat-head, nylon-coated (4) Silver 0.181 Nm (1.85 kgf-cm)

90

8

9

9

1210 Power button board For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68 1070 Wireless WAN card on page 69 1120 Built-in battery or dummy battery on page 73 1130 Thermal fan on page 75 1180 System board assembly on page 81 1190 LCD unit on page 83

Chapter 7. Removing or replacing a FRU 85

Removal steps of the power button board

1 1

2

Step Screw (quantity) Color Torque

1 M2 L3 mm, flat-head, nylon-coated (2) Black 0.181 Nm (1.85 kgf-cm)

When installing: Ensure that the connector is attached firmly.

1220 Keyboard assembly

Removal steps of the keyboard assembly

To replace the keyboard assembly, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1030 Keyboard on page 61 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68 1070 Wireless WAN card on page 69 1080 M.2 solid-state drive on page 70 1090 Coin-cell battery on page 71 1110 dc-in bracket and dc-in cable assembly on page 72 1120 Built-in battery or dummy battery on page 73 1130 Thermal fan on page 75 1140 Speaker assembly on page 77 1150 Smart card assembly or dummy smart card on page 78 1160 Fingerprint reader assembly on page 79 1170 Board for the trackpad and TrackPoint buttons on page 80 1180 System board assembly on page 81 1190 LCD unit on page 83 1210 Power button board on page 85

Removing an LCD FRU for models without touch panel This section provides instructions on how to remove an LCD FRU for models without touch panel.

86 Hardware Maintenance Manual

2010 LCD bezel assembly Important: Once an LCD bezel assembly is removed, it cannot be used anymore. A new LCD bezel assembly is required for replacement.

Removal steps of the LCD bezel assembly

When installing: Ensure that all the latches are attached firmly.

2020 LCD panel and LCD cable For access, remove these FRUs in order: 1010 Removable battery on page 59 2010 LCD bezel assembly on page 87

Removal steps of LCD panel and LCD cable

1

1

1

1 2

Step Screw (quantity) Color Torque

1 M2 L2.5 mm, flat-head, nylon-coated (4) Black 0.181 Nm (1.85 kgf-cm)

Chapter 7. Removing or replacing a FRU 87

5

4

3

When installing:

For Panasonic LCD, ensure that you apply the AL sheets a first, and then paste the sponges b on the top of the AL sheets as shown in the following illustration.

aa

b b

For other LCD, apply the sponges as shown in the following illustration.

88 Hardware Maintenance Manual

Ensure the LCD connector is attached firmly.

2030 Hinges and hinge brackets For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68 1070 Wireless WAN card on page 69 1130 Thermal fan on page 75 1180 System board assembly on page 81 1190 LCD unit on page 83 2010 LCD bezel assembly on page 87

Removal steps of the hinges

1 11

1 1 1

Step Screw (quantity) Color Torque

1 M2.5 L2.5 mm, big-head, nylon-coated (6) Silver 0.294 Nm (3 kgf-cm)

Chapter 7. Removing or replacing a FRU 89

2

2

Removal steps of the hinge brackets

2040 Camera/microphone card For access, remove these FRUs in order: 1010 Removable battery on page 59 2010 LCD bezel assembly on page 87 2020 LCD panel and LCD cable on page 87

90 Hardware Maintenance Manual

Removal steps of the camera/microphone card

1

When installing: Ensure that the connector is attached firmly.

2

2050 LED cable assembly For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68

Chapter 7. Removing or replacing a FRU 91

1070 Wireless WAN card on page 69 1130 Thermal fan on page 75 1180 System board assembly on page 81 1190 LCD unit on page 83 2010 LCD bezel assembly on page 87 2020 LCD panel and LCD cable on page 87 2030 Hinges and hinge brackets on page 89

Removal step of the LED cable assembly

1 1

2

2

2

2

3

3

3

2060 Antenna kit and LCD rear cover assembly

Removal steps of the antenna kit

For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68

92 Hardware Maintenance Manual

1070 Wireless WAN card on page 69 1130 Thermal fan on page 75 1180 System board assembly on page 81 1190 LCD unit on page 83 2010 LCD bezel assembly on page 87 2020 LCD panel and LCD cable on page 87 2030 Hinges and hinge brackets on page 89

11 1 1

2

2

2

2

2

2

2

2

3

3

3

3

Chapter 7. Removing or replacing a FRU 93

Cable routing: When you install the antenna kit, route the cables as shown in the following illustration. Ensure that the cables are not subject to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.

c

d

a

b

a Black cable (WLAN auxiliary)

b Blue cable (WWAN auxiliary)

c Orange cable (WWAN main)

d Gray cable (WLAN main)

Antenna locations b c da

94 Hardware Maintenance Manual

a WLAN auxiliary antenna (black)

b WWAN auxiliary antenna (blue)

c WWAN main antenna (red)

d WLAN main antenna (gray)

Removal steps of the LCD rear cover assembly

To replace the LCD rear cover assembly, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68 1070 Wireless WAN card on page 69 1130 Thermal fan on page 75 1180 System board assembly on page 81 1190 LCD unit on page 83 2010 LCD bezel assembly on page 87 2020 LCD panel and LCD cable on page 87 2030 Hinges and hinge brackets on page 89 2040 Camera/microphone card on page 90 2050 LED cable assembly on page 91 Removal steps of the antenna kit on page 92

Removing an LCD FRU for models with touch panel This section provides instructions on how to remove an LCD FRU for models with touch panel.

3010 LCD front sheet bezel Important: Once an LCD front sheet bezel is removed, it cannot be used anymore. A new LCD front sheet bezel is required for replacement.

Removal steps of the LCD front sheet bezel

When installing: Ensure that all the latches are attached firmly.

3020 LCD panel assembly and LCD cable For access, remove these FRUs in order:

Chapter 7. Removing or replacing a FRU 95

1010 Removable battery on page 59 3010 LCD front sheet bezel on page 95

Removal steps of the LCD panel assembly and LCD cable

The LCD panel assembly consists of an LCD panel and an LCD bezel. The LCD bezel is glued to the back side of the LCD panel.

Important: Once an LCD bezel is removed, it cannot be used anymore. A new LCD bezel is required for replacement.

12

3

4

4

4

5

Step Screw (quantity) Color Torque

4 M2.5 L4 mm, big-head, nylon-coated (3) Silver 0.294 Nm (3 kgf-cm)

96 Hardware Maintenance Manual

8

7

6

When installing: Ensure that the connector is attached firmly.

3030 Hinges For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68 1070 Wireless WAN card on page 69 1130 Thermal fan on page 75 1180 System board assembly on page 81 1190 LCD unit on page 83 3010 LCD front sheet bezel on page 95 3020 LCD panel assembly and LCD cable on page 95

Removal steps of the hinges

1 1

1 1

Chapter 7. Removing or replacing a FRU 97

Step Screw (quantity) Color Torque

1 M2.5 L2.5 mm, big-head, nylon-coated (4) Silver 0.294 Nm (3 kgf-cm)

2

2

3040 Camera/microphone card For access, remove these FRUs in order: 1010 Removable battery on page 59 3010 LCD front sheet bezel on page 95 3020 LCD panel assembly and LCD cable on page 95

Removal steps of the camera/microphone card

1

When installing: Ensure that the connector is attached firmly.

98 Hardware Maintenance Manual

2

3050 Touch sensor card For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68 1070 Wireless WAN card on page 69 1130 Thermal fan on page 75 1180 System board assembly on page 81 1190 LCD unit on page 83 3010 LCD front sheet bezel on page 95 3020 LCD panel assembly and LCD cable on page 95

Chapter 7. Removing or replacing a FRU 99

Removal steps of the touch sensor card

12

3

When installing: Ensure that all the connectors are attached firmly.

4

3060 LED cable assembly For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68 1070 Wireless WAN card on page 69 1130 Thermal fan on page 75 1180 System board assembly on page 81 1190 LCD unit on page 83 3020 LCD panel assembly and LCD cable on page 95 3030 Hinges on page 97

100 Hardware Maintenance Manual

Removal step of the LED cable assembly

1 1

2

2

2

2

3

3

3

3070 Antenna kit and LCD rear cover assembly

Removal steps of the antenna kit

For access, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68 1070 Wireless WAN card on page 69 1130 Thermal fan on page 75 1180 System board assembly on page 81 1190 LCD unit on page 83 3020 LCD panel assembly and LCD cable on page 95 3030 Hinges on page 97

Chapter 7. Removing or replacing a FRU 101

1111

2

2

2

2

2

2

2

2

3

3

3

3

102 Hardware Maintenance Manual

Cable routing: When you install the antenna kit, route the cables as shown in the following illustration. Ensure that the cables are not subject to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.

b

c

d

a

a Black cable (WLAN auxiliary)

b Blue cable (WWAN auxiliary)

c Orange cable (WWAN main)

d Gray cable (WLAN main)

Antenna locations b c da

Chapter 7. Removing or replacing a FRU 103

a WLAN auxiliary antenna (black)

b WWAN auxiliary antenna (blue)

c WWAN main antenna (orange)

d WLAN main antenna (gray)

Removal steps of the LCD rear cover assembly

To replace the LCD rear cover assembly, remove these FRUs in order: 1010 Removable battery on page 59 1020 Base cover assembly on page 59 1040 Storage-drive stabilizer bar, internal storage drive, hard disk drive cable, and hard disk drive

bracket on page 66 1060 Wireless LAN card on page 68 1070 Wireless WAN card on page 69 1130 Thermal fan on page 75 1180 System board assembly on page 81 1190 LCD unit on page 83 3010 LCD front sheet bezel on page 95 3020 LCD panel assembly and LCD cable on page 95 3030 Hinges on page 97 3040 Camera/microphone card on page 98 3060 LED cable assembly on page 100 Removal steps of the antenna kit on page 101

104 Hardware Maintenance Manual

Appendix A. Notices

Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the users responsibility to evaluate and verify the operation of any other product, program, or service.

Lenovo may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents. You can send license inquiries, in writing, to:

Lenovo (United States), Inc. 1009 Think Place - Building One Morrisville, NC 27560 U.S.A. Attention: Lenovo Director of Licensing

LENOVO PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you.

This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice.

The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. The result obtained in other operating environments may vary.

Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.

Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk.

Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.

Copyright Lenovo 2015 105

Electronic emissions notices For electronic emission information on Class B digital devices, refer to the corresponding information in the User Guide.

Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both:

Lenovo ThinkPad TrackPoint ThinkPad logo

Microsoft and Windows are trademarks of the Microsoft group of companies.

Intel is a trademark of Intel Corporation in the U.S. and/or other countries.

Mini DisplayPort (mDP) and DisplayPort are trademarks of the Video Electronics Standards Association.

Other company, product, or service names may be the trademarks or service marks of others.

106 Hardware Maintenanc

Manualsnet FAQs

If you want to find out how the ThinkPad T550 Lenovo works, you can view and download the Lenovo ThinkPad T550 Laptop Hardware Maintenance Manual on the Manualsnet website.

Yes, we have the Hardware Maintenance Manual for Lenovo ThinkPad T550 as well as other Lenovo manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Hardware Maintenance Manual should include all the details that are needed to use a Lenovo ThinkPad T550. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Lenovo ThinkPad T550 Laptop Hardware Maintenance Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Lenovo ThinkPad T550 Laptop Hardware Maintenance Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Lenovo ThinkPad T550 Laptop Hardware Maintenance Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Lenovo ThinkPad T550 Laptop Hardware Maintenance Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Lenovo ThinkPad T550 Laptop Hardware Maintenance Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.