Contents

Lenovo C20-05 Computer User Guide PDF

1 of 73
1 of 73

Summary of Content for Lenovo C20-05 Computer User Guide PDF

Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

ideaideaideaCentreidea

Machine Types: F0B2 [C20-30]/F0B3 [C20-05]

Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Machine Types: F0B2 [C20-30]/F0B3 [C20-05]

First Edition (October 2014)25th

Copyright Lenovo 2014, 2015.

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925

Contents

Chapter 1. About this manual . . . . . 1 Important Safety Information . . . . . . . . . 1

Chapter 2. Safety information. . . . . 3 General safety . . . . . . . . . . . . . . . 3 Electrical safety . . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . 5 Handling electrostatic discharge-sensitive devices . . . . . . . . . . . . . . . . . 5 Grounding requirements . . . . . . . . . . . 6 Safety notices . . . . . . . . . . . . . . . 6

Chapter 3. General information . . . . 9 Specifications . . . . . . . . . . . . . . . 9

Chapter 4. General Checkout . . . . . 11

Chapter 5. Using the Setup Utility. . . 13 Starting the Lenovo BIOS Setup Utility program . 13 Viewing and changing settings . . . . . . . . 13 Using passwords. . . . . . . . . . . . . . 13 Enabling or disabling a device . . . . . . . . 15 Selecting a startup device . . . . . . . . . . 16 Changing booting mode . . . . . . . . . . . 17 Exiting the Lenovo BIOS Setup Utility program . . 17

Chapter 6. Symptom-to-FRU Index . . 19 Hard disk drive boot error . . . . . . . . . . 19 Power Supply Problems . . . . . . . . . . . 19

POST error codes . . . . . . . . . . . . . 20 Undetermined problems . . . . . . . . . . . 20

Chapter 7. Replacing hardware . . . . 21 General information. . . . . . . . . . . . . 21 Replacing the keyboard and mouse . . . . . . 22 Replacing the power adapter . . . . . . . . . 22 Removing the rear cover . . . . . . . . . . . 24 Replacing the hard disk drive . . . . . . . . . 29 Replacing a memory module . . . . . . . . . 31 Replacing the optical drive . . . . . . . . . . 32 Replacing the system fan . . . . . . . . . . 33 Replacing the Wi-Fi card. . . . . . . . . . . 34 Replacing the speaker system . . . . . . . . 35 Replacing the power switch board . . . . . . . 36 Replacing the motherboard or the heat-sink module . . . . . . . . . . . . . . . . . 37 Replacing the I/O Shielding. . . . . . . . . . 39 Replacing the camera . . . . . . . . . . . . 40 Replacing the converter board . . . . . . . . 41 Replacing the LED panel. . . . . . . . . . . 42

Chapter 8. FRU lists . . . . . . . . . . 47

Chapter 9. FRU lists . . . . . . . . . . 57

Chapter 10. Additional Service Information . . . . . . . . . . . . . . 67

Copyright Lenovo 2014, 2015 iii

iv Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 1. About this manual

This manual contains service and reference information for Lenovo C20-30/C20-05 Touch All-In-One computer listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products.

Before servicing a Lenovo product, be sure to read the Safety Information.

The description of the TV-tuner card in this manual applies only to computers with a TV-tuner card installed. It does not apply to computers without a TV-tuner card.

Important Safety Information Be sure to read all CAUTION and DANGER sections in this manual before following any of the instructions.

Veuillez lire toutes les consignes de type DANGER et ATTENTION du prsent document avant dexcuter les instructions.

Lesen Sie unbedingt alle Hinweise vom Typ ACHTUNG oder VORSICHT in dieser Dokumentation, bevor Sie irgendwelche Vorgnge durchfhren

Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel manuale prima di eseguire una qualsiasi delle istruzioni

Certifique-se de ler todas as instrues de cuidado e perigo neste manual antes de executar qualquer uma das instrues

Es importante que lea todas las declaraciones de precaucin y de peligro de este manual antes de seguir las instrucciones.

Copyright Lenovo 2014, 2015 1

2 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 2. Safety information

This chapter contains the safety information that you need to be familiar with before servicing a computer.

General safety Follow these rules to ensure general safety:

Keep the areas around the computer clear and clean during and after maintenance.

When lifting any heavy object:

1. Ensure you can stand safely without slipping.

2. Distribute the weight of the object equally across both feet.

3. Lift slowly. Never move suddenly or twist when you attempt to lift.

4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any objects that weigh more than 16 kg (35 lbs.) or objects that you think are too heavy for you.

Do not perform any action that would create a hazard for the customer, or would make the computer unsafe.

Before you start the computer, ensure that other service representatives and customer personnel are not in a position that would create a hazard for them.

Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the computer.

Keep your tool case away from areas that people may walk through to ensure no-one trips over it.

Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, tie or fasten it back.

Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately 8 centimeters (3 inches) from the end.

Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing. Remember: Metal objects are good electrical conductors.

Wear safety glasses when you are: hammering, drilling soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes.

After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective.

Reattach all covers correctly before returning the computer to the customer.

Electrical safety

CAUTION: Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect any attached power cords, telecommunication cables, network cables, and modem cables before you open the computer covers, unless instructed otherwise in the installation and configuration procedures.

Copyright Lenovo 2014, 2015 3

Observe the following rules when working on electrical equipment.

Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their equipment that contain small conductive fibers to decrease electrostatic discharge.

Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.

Do not work alone under hazardous conditions or near equipment that has hazardous voltages.

Disconnect all power before:

Performing a mechanical inspection

Working near power supplies

Removing or installing Field Replaceable Units (FRUs)

Before you start to work on the computer, unplug the power cord. If you cannot unplug it, ask the customer to power-off the electrical outlet that supplies power to the machine and to lock the electrical outlet in the off position.

If you need to work on a computer that has exposed electrical circuits, observe the following precautions:

Ensure that another person, familiar with the power-off controls, is near you. Remember: Another person must be there to switch off the power, if necessary.

Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back. Remember: There must be a complete circuit to cause electrical shock. By observing the above rule, you may prevent a current from passing through your body.

When using a tester, set the controls correctly and use the approved probe leads and accessories for that tester.

Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages; these instructions are in the safety sections of the maintenance information. Use extreme care when measuring high voltages.

Regularly inspect and maintain your electrical hand tools to ensure they are safe to use.

Do not use worn or broken tools and testers.

Never assume that power has been disconnected from a circuit. First, check that it has been powered off.

Always look carefully for possible hazards in your work area. Examples of these hazards are wet floors, non-grounded power extension cables, conditions that may cause or allow power surges, and missing safety grounds.

Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. This surface is conductive, and touching a live circuit can cause personal injury and damage to the computer.

Do not service the following parts with the power on when they are removed from their normal operating positions in a computer:

Power supply units

Pumps

Blowers and fans

Motor generators

and similar units. (This practice ensures correct grounding of the units.)

If an electrical accident occurs:

Use caution; do not become a victim yourself.

4 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Switch off power.

Send another person to get medical aid.

Safety inspection guide The intent of this inspection guide is to assist you in identifying potential hazards posed by these products. Each computer, as it was designed and built, had required safety items installed to protect users and service personnel from injury. This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of features or options not covered by this inspection guide.

If any hazards are present, you must determine how serious the apparent hazard could be and whether you can continue without first resolving the problem.

Consider the following items and the safety hazards they present:

Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock).

Explosive hazards, such as a damaged CRT face or bulging capacitor

Mechanical hazards, such as loose or missing hardware

The guide consists of a series of steps presented as a checklist. Begin the checks with the power off, and the power cord disconnected.

Checklist:

1. Check exterior covers for damage (loose, broken, or sharp edges).

2. Power-off the computer. Disconnect the power cord.

3. Check the power cord for:

a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and frame ground.

b. The power cord should be the appropriate type as specified in the parts listings.

c. Insulation must not be frayed or worn.

4. Remove the cover.

5. Check for any obvious alterations. Use good judgment as to the safety of any alterations.

6. Check inside the unit for any obvious hazards, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.

7. Check for worn, frayed, or pinched cables.

8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.

Handling electrostatic discharge-sensitive devices Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the computer, the part, the work mat, and the person handling the part are all at the same charge.

Notes:

1. Use product-specific ESD procedures when they exceed the requirements noted here.

2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.

When handling ESD-sensitive parts:

Chapter 2. Safety information 5

Keep the parts in protective packages until they are inserted into the product.

Avoid contact with other people while handling the part.

Wear a grounded wrist strap against your skin to eliminate static on your body.

Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.

Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.

Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.

Note: The use of a grounding system is desirable but not required to protect against ESD damage.

Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.

Use an ESD common ground or reference point when working on a double-insulated or battery-operated system. You can use coax or connector-outside shells on these systems.

Use the round ground-prong of the AC plug on AC-operated computers.

Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.

Safety notices The CAUTION and DANGER safety notices in this section are provided in the language of English.

DANGER

Electrical current from power, telephone and communication cables is hazardous.

To avoid a shock hazard:

Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.

Connect all power cords to a properly wired and grounded electrical outlet.

Connect any equipment that will be attached to this product to a properly wired outlet.

When possible, use one hand only to connect or disconnect signal cables.

Never turn on any equipment when there is evidence of fire, water, or structural damage.

Disconnect the attached power cords, telecommunications cables, network cables, and modem cables before you open the device covers, unless instructed otherwise in the installation and configuration procedures.

Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.

6 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

To Connect To Disconnect

1. Turn everything OFF.

2. First, attach all cables to devices.

3. Attach signal cables to connectors.

4. Attach power cords to outlet.

5. Turn device ON.

1. Turn everything OFF.

2. First, remove power cords from outlets.

3. Remove signal cables from connectors.

4. Remove all cables from devices.

CAUTION: When replacing the lithium battery, use only Part Number 45C1566 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not:

Throw into or immerse in water

Heat to more than 100C (212F)

Repair or disassemble

Dispose of the battery as required by local ordinances or regulations.

CAUTION: When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or transmitters) are installed, note the following:

Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.

Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

DANGER

Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:

These diodes emit radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.

Chapter 2. Safety information 7

18 kg (37 lbs) 32 kg (70.5 lbs) 55 kg (121.2 lbs)

CAUTION: Use safe practices when lifting.

CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.

1

2

CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices.

8 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 3. General information

This chapter provides general information that applies to all computer models covered by this manual.

Specifications This section lists the physical specifications for your computer.

This section lists the physical specifications for your computer.

Type Lenovo C2030/2005 Touch Models

This section lists the physical specifications.

Environment

Air temperature:

Operating: 10 to 35C

Transit: -20 to 55C

Humidity:

Operating: 35% to 80%

Transit: 20% to 90% (40C)

Altitude: 86KPa to 106KPa

Electrical input:

Input voltage: 90V-264V(AC)

Input frequency: 47Hz-63Hz

Copyright Lenovo 2014, 2015 9

10 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 4. General Checkout

Attention: The drives in the computer you are servicing might have been rearranged or the drive startup sequence may have been changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or programs can be overwritten if you select an incorrect drive.

General error messages appear if a problem or conflict is found by an application, the operating system, or both. For an explanation of these messages, refer to the information supplied with that software package.

Use the following procedure to help determine the cause of the problem:

1. Power-off the computer and all external devices.

2. Check all cables and power cords.

3. Set all display controls to the middle position.

4. Power-on all external devices.

5. Power-on the computer.

Look for displayed error codes.

Look for readable instructions or a main menu on the display.

If you did not receive the correct response, proceed to step 6.

If you did receive the correct response, proceed to step 7.

6. If one of the following happens, follow the instruction given:

If the computer displays a POST error, go to POST error codes.

If the computer hangs and no error is displayed, continue at step 7.

7. If the test stops and you cannot continue, replace the last device tested.

Copyright Lenovo 2014, 2015 11

12 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 5. Using the Setup Utility

The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating system settings might override any similar settings in the Setup Utility program.

Starting the Lenovo BIOS Setup Utility program To start the Lenovo BIOS Setup Utility program, do the following:

1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer.

2. Press and hold the F1 key then turn on the computer. When the Lenovo BIOS Setup Utility program is displayed, release the F1 key.

Note: If a Power-On Password or an Administrator Password has been set, the Setup Utility program menu will not be displayed until you type your password. For more information, see Using passwords.

Viewing and changing settings System configuration options are listed in the Lenovo BIOS Setup Utility program menu. To view or change settings, see Starting the Setup Utility program.

You must use the keyboard when using the Lenovo BIOS Setup Utility menu. The keys used to perform various tasks are displayed on the bottom of each screen.

Using passwords You can use the Lenovo BIOS Setup Utility program to set passwords to prevent unauthorized persons from gaining access to your computer and data. See Starting the Setup Utility program. The following types of passwords are available:

Administrator Password

Power-On Password

You do not have to set any passwords to use your computer. However, if you decide to set passwords, read the following sections.

Password considerations

A password can be any combination of letters and numbers up to 16 characters (a-z and 0-9). For security reasons, it is a good idea to use a strong password that cannot be easily compromised. We suggest that passwords should follow these rules:

For a strong password, use 7-16 characters and a mix of letters and numbers.

Do not use your name or your user name.

Do not use a common word or a common name.

Use something significantly different from your previous password.

Attention: Administrator and Power-On passwords are not case sensitive.

Copyright Lenovo 2014, 2015 13

Administrator Password

Setting an Administrator Password deters unauthorized persons from changing configuration settings. You might want to set an Administrator Password if you are responsible for maintaining the settings of several computers.

After you set an Administrator Password, a password prompt is displayed every time you access the Lenovo BIOS Setup Utility program.

If both the Administrator and Power-On Password are set, you can type either password. However, you must use your Administrator Password to change any configuration settings.

Setting, changing, or deleting an Administrator Password

To set an Administrator Password, do the following:

Note: A password can be any combination of letters and numbers up to 16 characters (a-z and 0-9). For more information, see Password considerations on page 13.

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Security menu, select Set Administrator Password and press the Enter key.

3. The password dialog box will be displayed. Type the password then press the Enter key.

4. Retype the password to confirm, then press the Enter key. If you typed the password correctly, the password will be installed. A Setup Notice will be displayed confirming that your changes has been saved.

5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

6. Select Save Changes and Exit from the menu.

To change an Administrator Password, do the following:

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Security menu, select Set Administrator Password and press the Enter key.

3. The password dialog box will be displayed. Type the current password then press the Enter key.

4. Type the new password, then press the Enter key. Retype the new password to confirm it. If you typed the new password correctly, the new password will be installed. A Setup Notice will be displayed confirming that your changes have been saved.

5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

6. Select Save Changes and Exit from the menu.

To delete a previously set Administrator Password, do the following :

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Security menu, select Set Administrator Password and press the Enter key.

3. The password dialog box will be displayed. Type the current password and press the Enter key.

4. Leave each new password line item blank, then press the Enter key. A Setup Notice will be displayed confirming that your changes have been saved.

5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

6. Select Save Changes and Exit from the menu.

14 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Power-On Password

When a Power-On Password is set, you cannot start the Lenovo BIOS Setup Utility program until a valid password is typed from the keyboard.

Setting, changing, or deleting a Power-On Password

Note: A password can be any combination of letters and numbers up to 16 characters (a-z and 0-9).

To set a Power-On Password, do the following:

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Security menu, select Set Power-On Password and press the Enter key.

3. The password dialog box will be displayed. Type the password, then press the Enter key.

4. Retype the password to confirm. If you typed the password correctly, the password will be installed.

5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

6. Select Save Changes and Exit from the menu.

To change a Power-On Password, do the following:

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Security menu, select Set Power-On Password and press the Enter key.

3. The password dialog box will be displayed. Type the current password then press the Enter key.

4. Type the new password, then press the Enter key. Retype the new password to confirm it. If you typed the new password correctly, the new password will be installed. A Setup Notice will be displayed confirming that your changes have been saved.

5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

6. Select Save Changes and Exit from the menu.

To delete a previously set Power-On Password, do the following :

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Security menu, select Set Power-On Password and press the Enter key.

3. The password dialog box will be displayed. Type the current password and press the Enter key.

4. Leave each new password line item blank, then press Enter. A Setup Notice will be displayed confirming that your changes have been saved.

5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

6. Select Save Changes and Exit from the menu.

Enabling or disabling a device The Devices options is used to enable or disable user access to the following:

USB Functions Select whether to enable or disable USB (Universal Serial Bus) functions. If the functions are disabled, no USB devices can be used.

Chapter 5. Using the Setup Utility 15

SATA Mode Select Disabled/IDE/AHCI mode. Device driver support is required for AHCI or RAID. Depending on how the hard disk drive image was installed, changing this setting may prevent the system from booting.

Onboard Audio Controller Select whether to enable or disable the Onboard Audio Controller. When this feature is set to Disabled all devices connected to the audio connectors (e.g. headphones or a microphone) are disabled and cannot be used.

Onboard Ethernet Controller or LAN Boot Agent Select whether to enable or disable theOnboard Ethernet Controller, or select whether to enable or disable load onboard PXE (Preboot Execution Environment).

To enable or disable a device, do the following:

1. Start the Setup Utility program (see Starting the Setup Utility program on page 13).

2. From the Setup Utility program menu, select Devices.

3. Select an option as follows:

Select USB Setup, press the Enter key, then select USB Functions.

Select ATA Drivers Setup, press the Enter key, then select SATA Mode.

Select Audio Setup, press the Enter key, then select Onboard Audio Controller.

Select Network Setup, press the Enter key, then select Onboard Ethernet Support or LAN Boot Agent.

4. Select Disabled or Enabled and press the Enter key.

5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

6. Select Save Changes and Exit from the menu.

Notes:

a. If you do not want to save the settings, select Discard Changes and Exit from the menu.

Selecting a startup device If your computer does not boot from a device such as the CD/DVD-ROM drive disk or hard disk as expected, follow one of the procedures below.

Selecting a temporary startup device

Use this procedure to start up from any boot device.

Note: Not all CDs, DVDs or hard disk drives are bootable.

1. Turn off your computer.

2. Press and hold the F12 key then turn on the computer. When the Startup Device Menu appears, release the F12 key.

Note: If the Startup Device Menu does not display using these steps, repeatedly press and release the F12 key rather than keeping it pressed when turning on the computer.

3. Use and arrows to select the desired startup device from the Startup Device Menu and press the Enter key to begin.

Note: Selecting a startup device from the Startup Device Menu does not permanently change the startup sequence.

16 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Selecting or changing the startup device sequence

To view or permanently change the configured startup device sequence, do the following:

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Lenovo BIOS Setup Utility program main menu, select the Startup option.

3. Press the Enter key, and select the devices for the Primary Boot Sequence. Read the information displayed on the right side of the screen.

4. Use - and arrows to select a device. Use the <+> or <-> keys to move a device up or down. Use the <> key to exclude the device from or include the device in the boot sequence.

5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

6. Select Save Changes and Exit from the menu.

Notes:

a. If you do not want to save the settings, select Discard Changes and Exit from the menu.

b. If you have changed these settings and want to return to the default settings, select Load Optimal Defaults from the menu.

Changing booting mode There are two boot modes UEFI and Legacy for your computer. The default boot mode for your computer is the UEFI mode. If you need to install a legacy Windows operating system (any operating system before Windows 8) on your computer, you must change the boot mode to Legacy support. The legacy Windows operating system cannot be installed if you dont change the boot mode.

To change the booting mode, do the following:

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Lenovo BIOS Setup Utility program main menu, select the Startup option.

3. Select the Boot Priority, then press Enter key. From the pop up Boot Priority window choose Legacy mode.

4. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

5. Select Save Changes and Exit from the menu.

Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. You might have to press the Esc key several times. Do one of the following:

If you want to save the new settings, select Save Changes and Exit from the menu. When the Save & reset window shows, select the Yes button, and then press the Enter key to exit the Lenovo BIOS Setup Utility program.

If you do not want to save the settings, select Discard Changes and Exit from the menu. When the Reset Without Saving window shows, select the Yes button, and then press the Enter key to exit the Lenovo BIOS Setup Utility program.

Chapter 5. Using the Setup Utility 17

18 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 6. Symptom-to-FRU Index

The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first. Always begin with Chapter 4, General Checkout, on page 11. This index can also be used to help you decide which FRUs to have available when servicing a computer. If you are unable to correct the problem using this index, go to Undetermined problems on page 20.

Notes:

If you have both an error message and an incorrect audio response, diagnose the error message first.

If you cannot run the diagnostic tests or you get a diagnostic error code when running a test but did receive a POST error message, diagnose the POST error message first.

If you did not receive any error message look for a description of your error symptoms in the first part of this index.

Hard disk drive boot error A hard disk drive boot error can have the following causes.

Error FRU/Action

The startup drive is not included in the boot sequence configuration.

Check the configuration and ensure the startup drive is in the boot sequence.

No operating system is installed on the boot drive. Install an operating system on the boot drive.

The boot sector on the startup drive is corrupted. The drive must be formatted. Do the following:

1. Attempt to back up the data on the failing hard disk drive.

2. Use the operating system to format the hard disk drive.

The drive is defective. Replace the hard disk drive.

Power Supply Problems Follow these procedures if you suspect there is a power supply problem.

Check/Verify FRU/Action

Check that the following are properly installed:

Power Cord

On/Off Switch connector

System Board Power Supply connectors

Microprocessor connections

Reseat connectors

Check the power cord. Power Cord

Check the power-on switch. Power-on Switch

Copyright Lenovo 2014, 2015 19

POST error codes Each time you turn the computer on, it performs a series of tests to check that the system is operating correctly and that certain options are set. This series of tests is called the Power-On Self-Test, or POST. POST does the following:

Checks some basic motherboard operations

Checks that the memory is working correctly

Starts video operations

Verifies that the boot drive is working

POST Error Message Description/Action

Keyboard error Cannot initialize the keyboard. Make sure the keyboard is properly connected to the computer and that no keys are held pressed during POST. To purposely configure the computer without a keyboard, select Keyboardless operation in Startup and set the option to Enabled. The BIOS then ignores the missing keyboard during POST.

Reboot and Select proper Boot device or Insert Boot Media in selected Boot device

The BIOS was unable to find a suitable boot device. Make sure the boot drive is properly connected to the computer. Make sure you have bootable media in the boot device.

Undetermined problems 1. Power-off the computer.

2. Remove or disconnect the following components (if connected or installed) one at a time.

a. External devices (modem, printer, or mouse)

b. Extended video memory

c. External Cache

d. External Cache RAM

e. Hard disk drive

f. Disk drive

3. Power-on the computer to re-test the system.

4. Repeat steps 1 through 3 until you find the failing device or component.

If all devices and components have been removed and the problem continues, replace the system board.

20 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 7. Replacing hardware

Attention: Do not remove the computer cover or attempt any repair before reading the Important safety information in the Safety and Warranty Guide that was included with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at: http://support.lenovo.com.

Note: Use only parts provided by Lenovo.

General information Pre-disassembly instructions

Before starting the disassembly procedure, make sure that you do the following:

1. Turn off the power to the system and all peripherals.

2. Unplug all power and signal cables from the computer.

3. Place the system on a flat, stable surface.

Copyright Lenovo 2014, 2015 21

Replacing the keyboard and mouse To replace the keyboard and mouse:

Step 1. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Note: Your keyboard will be connected to a USB connector on one side or at the rear of the computer.

Step 4. Disconnect the defective keyboard cable from the computer and connect the new keyboard cable to the same connector.

Note: The mouse can be replaced using the same method.

Replacing the power adapter To replace the power adapter:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Locate the connector for the power cord. Refer to Rear view.

22 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Step 3. Disconnect the failing power adapter from the computer.

Step 4. To install the new power adapter:

a. Connect the new power adapter to the same connector.

Chapter 7. Replacing hardware 23

Removing the rear cover Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.

To remove the rear cover:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Lift up the rubbers that protect the 2 screws, remove the 2 screws that secure the rear cover to the front bezel.

Step 5. Use a plastic spudger or a flat head screw driver to pries up the stand cover as shown.

24 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Step 6. Remove the screw that secures the rear cover to the front bezel.

Step 7. Use the flat end of the plastic spudger to pries the computer feet to split them. 1

Chapter 7. Replacing hardware 25

Step 8. Use a mylar sheet insert into the slot in-between the rear cover and front bezel, best practice insert angel is 45 angel as shown.

Step 9. Sweep along the side, best practice sweep angel is keep the mylar sheet side line and the slot line in a 30 angel as shown.

Step 10. Use the mylar sheet or plastic card to sweep along the slot on the side to separate the rear cover from the front bezel as shown.

26 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 7. Replacing hardware 27

Step 11. Lift up the rear cover as shown.

28 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Step 12. Disconnect the LVDS cable to separate the rear cover from the front bezel.

Step 13. To reattach the rear cover:

a. Line up the rear cover with the front bezel and reconnect the LVDS cable.

b. Line up the holes on the rear cover with mounting holes on the front bezel, and place the rear cover into position.

c. Secure the rear cover to the front bezel with the three screws.

d. Reattach the stand cover and the rubber cover.

Replacing the hard disk drive Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace the hard disk drive:

Step 1. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to "Removing the rear cover".

Chapter 7. Replacing hardware 29

Step 5. Remove the 6 screws that secure the hard disk drive to the rear cover.

Step 6. Disconnect the data and power cable from the hard disk drive.

Step 7. Lift up the hard disk drive to remove it.

Step 8. Remove the 4 screws that secure the hard disk drive to the bracket.

30 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Step 9. To install the new hard disk drive:

a. Attach the bracket pieces to the new hard disk drive, and secure them with the 4 screws.

b. Slide the new hard disk drive into the hard disk drive bay.

c. Secure the new hard disk drive to the rear cover with the 6 screws.

d. Connect the data and power cables to the new hard disk drive.

Step 10. Reattach the rear cover, stand and stand cover.

Replacing a memory module Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace a memory module:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to Removing the rear cover.

Step 5. Push out the latches on both sides of the memory socket to release the memory module. Gently pull the memory module upward to remove it from its socket.

Step 6. To install the new memory module:

a. Align the new memory module with the memory socket, then insert it and push down on the top edge.

b. Make sure the latches lock the memory module in place.

Chapter 7. Replacing hardware 31

Step 7. Reattach the rear cover.

Replacing the optical drive Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before replacing the optical drive.

To replace the optical drive:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover, refer to Removing the rear cover.

Step 5. Remove the screw that secures the optical disk drive to the rear cover, and then slide out the optical drive as shown.

32 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Step 6. Use a small flat head screwdriver to press and push out the pins that secure the cover to the disk. 4 5

Step 7. Separate the cover from the defective optical drive.

Step 8. Install the new optical drive as follows:

a. Align the new optical drive with the cover, and then push the cover back into position.

b. Slide the new optical drive into the drive bay, then push it into position.

c. Secure the rear cover to the front bezel with the 2 screws.

d. Reattach the stand and the cover.

Replacing the system fan Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace the system fan:

Step 1. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to "Removing the rear cover".

Chapter 7. Replacing hardware 33

Step 5. Disconnect the power cable from the connector on the motherboard.

Step 6. Remove the 2 screws that secure the system fan to the rear cover.

Step 7. Lift up the system fan to remove it.

Step 8. To install the new system fan:

a. Line up the new system fan with the mounting holes on the rear cover and place it into position.

b. Secure the new system fan to the rear cover with the 2 screws.

c. Connect the new power cable to the connector on the motherboard.

Step 9. Reattach the rear cover.

Replacing the Wi-Fi card Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace the Wi-Fi card:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to "Removing the rear cover".

34 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Step 5. Disconnect the antenna and data cables from the Wi-Fi card.

Step 6. Remove the screw that secures the Wi-Fi card to the motherboard.

Step 7. Pull the Wi-Fi card upward to remove it from the socket.

Step 8. To install the new Wi-Fi card:

a. Insert the new Wi-Fi card into the card port and secure it with the screw.

b. Connect the antenna cables to the new Wi-Fi card.

Step 9. Reattach the rear cover.

Replacing the speaker system Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace the speaker system:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to "Removing the rear cover".

Chapter 7. Replacing hardware 35

Step 5. Disconnect the speaker cable from the connector on motherboard.

Step 6. Detach the speaker system from the rubber screws.

Step 7. To install the new speaker system:

a. Secure the new speaker system to the chassis with the rubber screws.

b. Connect the new speaker cable to the connector on the motherboard.

Step 8. Reattach the rear cover.

Replacing the power switch board Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace the power switch board:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to "Removing the rear cover".

36 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Step 5. Remove the screw that secures the power switch board to the rear cover, and then slide out the power switch board to remove it.

Step 6. Disconnect the power switch board cable from the connector on the motherboard.

Step 7. To install the power switch board:

a. Line up the holes on the new power switch board with the mounting holes on the rear cover and secure the new power switch board with the two screws.

b. Connect the data cable to the connector on the new motherboard.

Step 8. Reattach the rear cover.

Replacing the motherboard or the heat-sink module Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace the motherboard:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to Removing the rear cover.

Step 5. Remove all memory modules. Refer to Replacing a memory module.

Step 6. Remove the heat-sink. Refer to Replacing the heat-sink.

Step 7. Remove the Wi-Fi card. Refer to Replacing the Wi-Fi card.

Chapter 7. Replacing hardware 37

Step 8. Remove all the cables connected to the motherboard.

Step 9. Remove the five screws that secure the motherboard to the rear cover and push the pin to release the heat-sink as shown.

Step 10. Slide out the motherboard as shown.

Step 11. Remove the screws that secure the heat-sink module to the motherboard, and then lift up the heat-sink to remove it.

38 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Step 12. To install the new motherboard or the new heat-sink:

a. Attach the heat-sink, Wi-Fi card, memory modules to the motherboard.

b. Line up the holes on the new motherboard with the mounting holes on the rear cover and secure the new motherboard with the 8 screws.

c. Insert the notched end of the Wi-Fi card into the card port on the new motherboard and secure it with the screw.

d. Connect the antenna cable(s) to the Wi-Fi card.

e. Connect all the cables to the new motherboard.

Step 13. Reattach the rear cover.

Replacing the I/O Shielding Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace the I/O shielding:

Step 1. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to "Removing the rear cover".

Chapter 7. Replacing hardware 39

Step 5. Remove the three screws that secure the I/O shielding module to the motherboard.

Step 6. Lift up the I/O shielding to remove it.

Step 7. To install the new I/O shielding:

a. Line up the new I/O shielding module with the mounting holes on the motherboard.

b. Secure the new I/O shielding to the motherboard with the screws.

Step 8. Reattach the rear cover.

Replacing the camera Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace the camera:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to Removing the rear cover.

40 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Step 5. Pull the locking pins outward to release the camera module.

Step 6. Disconnect the data cable from the connector on the camera module.

Step 7. To install the new camera:

a. Connect the data cable to the new camera.

b. Slide the new camera into position and secure the camera with the two locking pins.

Step 8. Reattach the rear cover.

Replacing the converter board Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace the converter board:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to Removing the rear cover.

Chapter 7. Replacing hardware 41

Step 5. Disconnect the 2 cables from the converter board.

Step 6. Remove the screw that secures the converter board to the bracket.

Step 7. Lift up the converter board to remove it.

Step 8. To install the new converter board:

a. Line up the holes in the new converter board with the mounting holes on the bracket and secure the new converter board with the screw.

b. Connect the 2 cables to the new converter board.

Step 9. Reattach the rear cover.

Replacing the LED panel Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.

To replace the LED panel:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the rear cover. Refer to Removing the rear cover.

Step 5. Remove the converter board. Refer to Replacing the converter board.

Step 6. Remove the camera. Refer to Replacing the camera.

Step 7. Removing the converter bracket as shown.

42 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 7. Replacing hardware 43

Step 8. Disconnect the LVDS-camera and converter cables from the connectors on the LED panel.

Step 9. Remove the four screws that secures the LED panel to the front bezel, the LED panel is pinned to the front bezel, push all the pins outward to release the panel from the front bezel.

Step 10. Lift up the LED panel to separate from the front bezel, and then remove the two panel bracket by removing the two screws.

44 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Step 11. To install the new LED panel module:

a. Attach the panel bracket to the LED panel with the two screws.

b. Line up the panel assembly with the front bezel, then place the panel into position.

c. Secure the new panel to the front bezel with the four screws and pins.

d. Attach the LVDS-camera and converter cables to the connectors on the new LED panel.

e. Attach the converter bracket to the front bezel.

f. Attach the converter board to the bracket.

g. Attach the camera to the new LED panel.

Step 12. Reattach the rear cover.

Chapter 7. Replacing hardware 45

46 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 8. FRU lists

This chapter lists the information on the field replaceable units (FRUs) for Lenovo C2005 Touch All-In-One desktop computer.

Attention: Be sure to read and understand all the safety information before replacing any FRUs.

Notes: FRUs that have a 1 or 2 in the CRU column are Customer Replaceable Units (CRUs).

1 identifies parts that are fairly simple to replace, requiring few or no tools.

2 identifies parts that are slightly more difficult to replace.

N-identifies parts that are not to be replaced by the customer.

Item # Description Lenovo PN

BDPLANAR

C C2005 NOK E1-6010 UMA MB 5B20H03341

C C2005 W8P E1-6010 UMA MB 5B20H03391

C C2005 NOK E2-6110 UMA MB 5B20H03328

C C2005 W8P E2-6110 UMA MB 5B20H03378

C C2005 NOK 1G A4-6210 DIS MB 5B20H03316

C C2005 W8P 1G A4-6210 DIS MB 5B20H03366

C C2005 NOK 2G A6-6310 DIS MB 5B20H03305

C C2005 W8P 2G A6-6310 DIS MB 5B20H03360

C C2005 NOK A4-6210 UMA MB 5B20H03309

C C2005 W8P A4-6210 UMA MB 5B20H03364

C C2005 NOK A6-6310 UMA MB 5B20H03303

C C2005 W8P A6-6310 UMA MB 5B20H03355

C C2005 NOK A8-6410 UMA MB 5B20H03405

C C2005 W8P A8-6410 UMA MB 5B20H03347

C C2005 NOK 1G E2-6110 DIS MB 5B20H03396

C C2005 W8P 1G E2-6110 DIS MB 5B20H03335

C C2005 NOK 1G A6-6310 DIS MB 5B20H03383

C C2005 W8P 1G A6-6310 DIS MB 5B20H03322

C C2005 NOK 1G A8-6410 DIS MB 5B20H03372

C C2005 W8P 1G A8-6410 DIS MB 5B20H03312

C C2005 NOK 2G E2-6110 DIS MB 5B20H03398

C C2005 W8P 2G E2-6110 DIS MB 5B20H03336

C C2005 NOK 2G A4-6210 DIS MB 5B20H03384

C C2005 W8P 2G A4-6210 DIS MB 5B20H03323

C C2005 NOK 2G A8-6410 DIS MB 5B20H03373

C C2005 W8P 2G A8-6410 DIS MB 5B20H03315

N

Copyright Lenovo 2014, 2015 47

C C2005 W8S E1-6010 UMA MB 5B20H14344

C C2005 W8S E2-6110 UMA MB 5B20H14359

C C2005 W8S 1G A4-6210 DIS MB 5B20H14350

C C2005 W8S 2G A6-6310 DIS MB 5B20H14339

C C2005 W8S A4-6210 UMA MB 5B20H14360

C C2005 W8S A6-6310 UMA MB 5B20H14349

C C2005 W8S A8-6410 UMA MB 5B20H14368

C C2005 W8S 1G E2-6110 DIS MB 5B20H14357

C C2005 W8S 1G A6-6310 DIS MB 5B20H14348

C C2005 W8S 1G A8-6410 DIS MB 5B20H14338

C C2005 W8S 2G E2-6110 DIS MB 5B20H14358

C C2005 W8S 2G A4-6210 DIS MB 5B20H14347

C C2005 W8S 2G A8-6410 DIS MB 5B20H14367

CARDPOP

Converter Board C C2030 5C50H03402

Power Board C C2030 5C50H03382

N

MECHANICAL

Shielding DDR C C2030 TS 5M20H03297

MB EMIShield C C2030 5M20H03367

N

STAND

Stand C C2030 BLK 5SE0H03320

Stand C C2030 WHT 5SE0H03399

N

SPEAKERINT

Speaker C C2030 L+R 5SB0H03338 N

BRACKET

BRACKET HDD C C2030 500G 5B40H03317

BRACKET HDD C C2030 1T 5B40H03368

BRACKET ODD C C2030 5B40H03401

Bracket Camera C C2030 5B40H03321

N

CABLE

LVDS Cable C C2030 TS 5C10H03381

CABLE HDD SATA C C2030 5C10H03306

CABLE ODD SATA C C2030 5C10H03350

Power Board C C2030 FFC 5C10H03357

Antenna C C2030 Main+AUX 5A30H03395

N

48 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

COVER

Bezel ODD C C2030 BLK 5CB0H03358

Bezel ODD C C2030 WHT 5CB0H03298

Stand Cap C C2030 BLK 5CB0H03334

Stand Cap C C2030 WHT 5CB0H03327

Rear Cover C C2030 UMA N-ODD BLK 5CB0H03377

Rear Cover C C2030 UMA N-ODD WHT 5CB0H03314

Rear Cover C C2030 UMA ODD BLK 5CB0H03365

Rear Cover C C2030 UMA ODD WHT 5CB0H03304

Rear Cover C C2030 DIS N-ODD BLK 5CB0H03356

Rear Cover C C2030 DIS N-ODD WHT 5CB0H03406

Rear Cover C C2030 DIS ODD BLK 5CB0H03345

Rear Cover C C2030 DIS ODD WHT 5CB0H03394

N

FAN

FAN System C C20-30 UMA Delta 5F10G81031

FAN System C C20-30 UMA Sunon 5F10G81035

FAN System C C20-05 UMA Avc 5F10G81030

N

DISPLAY

LCD Module C C2030 Ofilm TS BLK 5D10H03332

LCD Module C C2030 Ofilm TS WHT 5D10H03390

LCD Module C C2030 TPK TS BLK 5D10H03339

LCD Module C C2030 TPK TS WHT 5D10H03385

N

HEATSINK

HEATSINK C C20-05 DIS Avc 5H40G81040

HEATSINK C C20-05 DIS CM 5H40G81038

HEATSINK C C20-05 UMA Avc 5H40G81041

HEATSINK C C20-05 UMA CM 5H40G81034

N

POWER

Delta ADP-65FD BE 65W adapter 36200352

Liteon PA-1650-72IA 65W adapter 36200353

ADP-90XD BD 54Y8917

PA-1900-72FA 54Y8917

1

HDD

WD XL500A WD5000AAKX-08U6AA0 500G HDD 16200544

Toshiba Mars DT01ACA050 500G HDD 16200512

ST Pharaoh 4K Non-MC ST500DM002 500GHDD 16200674

WD XL1000B WD10EZEX-08M2NA0 1TB HDD 16200613

Toshiba Mars DT01ACA100 1TB HDD 16200513

ST Grenada BP2 ST1000DM003 1TB HDD 16200688

N

Chapter 8. FRU lists 49

ODD

PSN UJ8FB Slim Tray Rambo w/o bezel 25215310

HLDS GUB0N Slim Tray Rambo w/o bezel 00FC442

PLDS DU-8A5SH Tray Rambo w/o bezel LSOPU 25214499

PLDS DU-8A6SH Tray Rambo w/o bezel 00FC442

N

RAM

HMT425S6AFR6A-PB 2GB D3L-1600S Memory-HF 1100643

MT4KTF25664HZ-1G6E1 2GB D3L-1600S Memory 1100956

Mic_R D9PSH 2GB D3L-1600S Memory-HF 1100965

M471B5173DB0-YK0 4GB D3L-1600S Memory-HF 1100942

HMT451S6BFR8A-PB 4GB D3L-1600S Memory-HF 1100985

HMT451S6AFR8A-PB 1100638

MT8KTF51264HZ-1G6E1 4GB D3L-1600S Memory-HF 1100957

Mic_R D9QBJ 4GB D3L-1600S Memory-HF 1100967

M471B5674QH0-YK0 2GB D3L-1600S Memory-HF 1100983

M471B5173DB0-YK0 4GB D3L-1600S Memory-HF 1100942

HMT425S6AFR6A-PB 2GB D3L-1600S Memory-HF 1100643

HMT451S6BFR8A-PB 4GB D3L-1600S Memory-HF 1100985

Mic_R D9PSH 2GB D3L-1600S Memory-HF 1100965

Mic_R D9QBJ 4GB D3L-1600S Memory-HF 1100967

M471B1G73DB0-YK0 8GB D3L-1600S Memory-HF 1100943

HMT41GS6BFR8A-PB 8GB D3L-1600S Memory-HF 1100986

HMT41GS6AFR8A-PB 1100634

MT16KTF1G64HZ-1G6E1 1100635

Mic_R D9QBJ 8GB D3L-1600S Memory-HF 1101012

N

Wifi Combo

Liteon WB335 1x1BGN+BT4.0 HMC 20200437

CBT RTL8723BE 1x1BN+BT4.0 PCIE HMC 20200440

LTN RTL8821AE 1x1ac+BT4.0 Combo HMC 11202485

CBT RTL8821AE 1x1ac BT combo HMC 20200571

N

Camera

AVC 720P 5821 Hi162 WB 1DM S Cam 20200643

Bison 720P 5840 Hi162 WB 1DM S Cam 20200644

LT 720P 5840 Hi162 WB 1DM S Cam 20200667

N

50 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

KB & Mouse

Liteon LXH-SM-8825 Black Silk Mouse-LVT 25200528

Chicony LXH-MSU-1111 Black Silk Mouse-LVT 25200529

Sunrex LXH-EMS-10ZA Black Silk Mouse-LVT 25200530

Liteon LXH-SM-8825 W-Silk Mouse 25201068

Sunrex LXH-EMS-10ZA W-Silk Mouse 25201322

Liteon SM-8861(WW) Mouse Black 25203464

Liteon SM-8861 Mouse(No Battery) Black 25203465

Liteon SM-8861 Mouse(MY) Black 25203466

Liteon SM-8861(JP) Mouse-Black 25205773

Liteon SM-8861(WW) 2.4G Mouse White 25211016

Liteon SM-8861 2.4G Mouse(No Battery)WTE 25211017

Liteon SM-8861 2.4G Mouse(MY) White 25211018

Liteon SM-8861 2.4G Mouse(JP) White 25211019

Sunrex EKB-10YA(US) B-Silk USB KB-LVT8 25209111

Primax KB4721(US) B-Silk USB KB-LVT8 25209112

Sunrex EKB-10YA(TW) B-Silk USB KB-LVT8 25209114

Sunrex EKB-10YA(TH) B-Silk USB KB-LVT8 25209115

Sunrex EKB-10YA(CZ-SL) B-S USB KB-LVT8 25209116

Sunrex EKB-10YA(IN) B-Silk USB KB-LVT8 25209117

Sunrex EKB-10YA(RU) B-Silk USB KB-LVT8 25209118

Sunrex EKB-10YA(UK) B-Silk USB KB-LVT8 25209119

Sunrex EKB-10YA(Nordic) B-S USB KB-LVT8 25209120

Sunrex EKB-10YA(LA) B-Silk USB KB-LVT8 25209121

Sunrex EKB-10YA(AR) B-Silk USB KB-LVT8 25209122

Sunrex EKB-10YA(SW) B-Silk USB KB-LVT8 25209123

Sunrex EKB-10YA(GE) B-Silk USB KB-LVT8 25209124

Sunrex EKB-10YA(TR) B-Silk USB KB-LVT8 25209125

Sunrex EKB-10YA(SP) B-Silk USB KB-LVT8 25209126

Sunrex EKB-10YA(SL) B-Silk USB KB-LVT8 25209127

Sunrex EKB-10YA(IT) B-Silk USB KB-LVT8 25209128

Sunrex EKB-10YA(HB) B-Silk USB KB-LVT8 25209129

Sunrex EKB-10YA(FR) B-Silk USB KB-LVT8 25209130

Sunrex EKB-10YA(GK) B-Silk USB KB-LVT8 25209131

Sunrex EKB-10YA(HG) B-Silk USB KB-LVT8 25209132

Sunrex EKB-10YA(BG) B-Silk USB KB-LVT8 25209133

Sunrex EKB-10YA(HR) B-Silk USB KB-LVT8 25209134

Sunrex EKB-10YA(JP) B-Silk USB KB-LVT8 25209135

Sunrex EKB-10YA(EN-FR) B-S USB KB-LVT8 25209136

Sunrex EKB-10YA(PT) B-Silk USB KB-LVT8 25209137

1

Chapter 8. FRU lists 51

Sunrex EKB-10YA(BE-EN) B-S USB KB-LVT8 25209138

Sunrex EKB-10YA(DU) B-S USB KB-LVT8 25209139

Sunrex EKB-10YA(US) W-Silk USB KB-LVT8 25209145

Primax KB4721(US) W-Silk USB KB-LVT8 25209146

Sunrex EKB-10YA(TW) W-Silk USB KB-LVT8 25209147

Sunrex EKB-10YA(TH) W-Silk USB KB-LVT8 25209148

Sunrex EKB-10YA(CZ-SL) W-S USB KB-LVT8 25209149

Sunrex EKB-10YA(IN) W-Silk USB KB-LVT8 25209150

Sunrex EKB-10YA(RU) W-Silk USB KB-LVT8 25209151

Sunrex EKB-10YA(UK) W-Silk USB KB-LVT8 25209152

Sunrex EKB-10YA(Nordic) W-S USB KB-LVT8 25209153

Sunrex EKB-10YA(LA) W-Silk USB KB-LVT8 25209154

Sunrex EKB-10YA(AR) W-Silk USB KB-LVT8 25209155

Sunrex EKB-10YA(SW) W-Silk USB KB-LVT8 25209156

Sunrex EKB-10YA(GE) W-Silk USB KB-LVT8 25209157

Sunrex EKB-10YA(TR) W-Silk USB KB-LVT8 25209158

Sunrex EKB-10YA(SP) W-Silk USB KB-LVT8 25209159

Sunrex EKB-10YA(SL) W-Silk USB KB-LVT8 25209160

Sunrex EKB-10YA(IT) W-Silk USB KB-LVT8 25209161

Sunrex EKB-10YA(HB) W-Silk USB KB-LVT8 25209162

Sunrex EKB-10YA(FR) W-Silk USB KB-LVT8 25209163

Sunrex EKB-10YA(GK) W-Silk USB KB-LVT8 25209164

Sunrex EKB-10YA(HG) W-Silk USB KB-LVT8 25209165

Sunrex EKB-10YA(BG) W-Silk USB KB-LVT8 25209166

Sunrex EKB-10YA(HR) W-Silk USB KB-LVT8 25209167

Sunrex EKB-10YA(JP) W-Silk USB KB-LVT8 25209168

Sunrex EKB-10YA(EN-FR) W-S USB KB-LVT8 25209169

Sunrex EKB-10YA(PT) W-Silk USB KB-LVT8 25209170

Sunrex EKB-10YA(BE-EN) W-S USB KB-LVT8 25209171

Sunrex EKB-10YA(DU) W-S USB KB-LVT8 25209172

Liteon SK-8861(US) 2.4G KB-Black8 25209175

Liteon SK-8861(US-MY) 2.4G KB-Black8 25209176

Liteon SK-8861(TW) 2.4G KB-Black8 25209177

Liteon SK-8861(TH) 2.4G KB-Black8 25209178

Liteon SK-8861(CS-SK) 2.4G KB-Black8 25209179

Liteon SK-8861(US-IN) 2.4G KB-Black8 25209180

Liteon SK-8861(RU) 2.4G KB-Black8 25209181

Liteon SK-8861(GB) 2.4G KB-Black8 25209182

Liteon SK-8861(Nordic) 2.4G KB-Black8 25209183

Liteon SK-8861(LA) 2.4G KB-Black8 25209184

52 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Liteon SK-8861(LA-AR) 2.4G KB-Black8 25209185

Liteon SK-8861(SA) 2.4G KB-Black8 25209186

Liteon SK-8861(CH) 2.4G KB-Black8 25209187

Liteon SK-8861(DE) 2.4G KB-Black8 25209188

Liteon SK-8861(TR) 2.4G KB-Black8 25209189

Liteon SK-8861(ES) 2.4G KB-Black8 25209190

Liteon SK-8861(SL) 2.4G KB-Black8 25209191

Liteon SK-8861(IT) 2.4G KB-Black8 25209192

Liteon SK-8861(IL) 2.4G KB-Black8 25209193

Liteon SK-8861(FR) 2.4G KB-Black8 25209194

Liteon SK-8861(GR) 2.4G KB-Black8 25209195

Liteon SK-8861(HU) 2.4G KB-Black8 25209196

Liteon SK-8861(BG) 2.4G KB-Black8 25209197

Liteon SK-8861(KR) 2.4G KB-Black8 25209198

Liteon SK-8861(JP) 2.4G KB-Black8 25209199

Liteon SK-8861(EN-FR) 2.4G KB-Black8 25209200

Liteon SK-8861(PT) 2.4G KB-Black8 25209201

Liteon SK-8861(BE-EN) 2.4G KB-Black8 25209202

Liteon SK-8861(DU) 2.4G KB-Black8 25209203

Liteon SK-8861(US) 2.4G KB-White8 25210987

Liteon SK-8861(US-MY) 2.4G KB-White8 25210988

Liteon SK-8861(TW) 2.4G KB-White8 25210989

Liteon SK-8861(TH) 2.4G KB-White8 25210990

Liteon SK-8861(CS-SK) 2.4G KB-White8 25210991

Liteon SK-8861(US-IN) 2.4G KB-White8 25210992

Liteon SK-8861(RU) 2.4G KB-White8 25210993

Liteon SK-8861(GB) 2.4G KB-White8 25210994

Liteon SK-8861(Nordic) 2.4G KB-White8 25210995

Liteon SK-8861(LA) 2.4G KB-White8 25210996

Liteon SK-8861(LA-AR) 2.4G KB-White8 25210997

Liteon SK-8861(SA) 2.4G KB-White8 25210998

Liteon SK-8861(CH) 2.4G KB-White8 25210999

Liteon SK-8861(DE) 2.4G KB-White8 25211000

Liteon SK-8861(TR) 2.4G KB-White8 25211001

Liteon SK-8861(ES) 2.4G KB-White8 25211002

Liteon SK-8861(SL) 2.4G KB-White8 25211003

Liteon SK-8861(IT) 2.4G KB-White8 25211004

Liteon SK-8861(IL) 2.4G KB-White8 25211005

Liteon SK-8861(FR) 2.4G KB-White8 25211006

Liteon SK-8861(GR) 2.4G KB-White8 25211007

Chapter 8. FRU lists 53

Liteon SK-8861(HU) 2.4G KB-White8 25211008

Liteon SK-8861(BG) 2.4G KB-White8 25211009

Liteon SK-8861(KR) 2.4G KB-White8 25211010

Liteon SK-8861(JP) 2.4G KB-White8 25211011

Liteon SK-8861(EN-FR) 2.4G KB-White8 25211012

Liteon SK-8861(PT) 2.4G KB-White8 25211013

Liteon SK-8861(BE-EN) 2.4G KB-White8 25211014

Liteon SK-8861(US-EU) 2.4G KB-White8 25211015

Power Cord

Longwell B LAck single head 1.0M 3wire ULCSA Power Cord 31033857

Volex 1.0M C5 US Power Cord 31033858

Luxshare 1.0M C5 US Power Cord 31049517

Longwell B LAck single head 1.0M SAA Power Cord 31035397

Volex 1.0M C5 Macao Power Cord 31049500

Luxshare 1.0M C5 Macao Power Cord 31049520

Longwell 1.0M C5 2pin Japan Power Cord 31503423

Volex 1.0M C5 2pin Japan Power Cord 31503424

Luxshare 1.0M C5 2pin Japan Power Cord 31503425

Grandsun B LAck single head 1.0M 3wire CCC Power Cord(R) 31032953

Luxshare 1.0M C5 CCC Power Cord 31045147

Volex 1.0M C5 UK Power Cord 31049496

Luxshare 1.0M C5 UK Power Cord 31503352

Longwell B LAck single head 1.0M ASTA Power Cord 31035396

Longwell B LAck single head 1.0M VDE Power Cord 31035332

Volex 1.0M C5 Europe Power Cord 31049497

Luxshare 1.0M C5 Europe Power Cord 31049518

Longwell B LAck single head 1.0M India Power Cord 31035395

Luxshare 1.0M C5 India Power Cord 31503353

Longwell B LAck single head 1.0M Italy C5 Power Cord 31039104

Luxshare 1.0M C5 Italy Power Cord 31503359

Volex 1.0M C5 Italy Power Cord 31049504

Longwell B LAck single head 1.0M Brazil Power Cord 31035828

Luxshare 1.0M C5 Brazil Power Cord 31503357

Volex 1.0M C5 Brazil Power Cord 31049505

Longwell B LAck single head 1.0M Argentina C5 Power Cord 31039100

Luxshare 1.0M C5 LA Power Cord 31503356

Volex 1.0M C5 LA Power Cord 31049507

Longwell B LAck single head 1.0M Denmark C5 Power Cord 31039101

Luxshare 1.0M C5 Denmark Power Cord 31503360

Volex 1.0M C5 Denmark Power Cord 31049503

1

54 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Longwell B LAck single head 1.0M Switzer LAnd C5 Power Cord 31039103

Luxshare 1.0M C5 Switzer LAnd Power Cord 31503361

Volex 1.0M C5 Switzer LAnd Power Cord 31049508

Longwell B LAck single head 1.0M Israel C5 Power Cord 31039107

Luxshare 1.0M C5 Israel Power Cord 31503362

Volex 1.0M C5 Israel Power Cord 31049502

Longwell B LAck single head 1.0M Taiwan C5 Power Cord 31038885

Luxshare 1.0M C5 Taiwan Power Cord 31503354

Volex 1.0M C5 Taiwan Power Cord 31049499

Longwell B LAck single head 1.0M Korea C5 Power Cord 31039106

Luxshare 1.0M C5 Korea Power Cord 31503358

Volex 1.0M C5 Korea Power Cord 31049498

Longwell B LAck single head 1.0M SA C5 Power Cord 31039105

Luxshare 1.0M C5 South Africa Power Cord 31503355

Volex 1.0M C5 South Africa Power Cord 31049501

Chapter 8. FRU lists 55

56 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 9. FRU lists

This chapter lists the information on the field replaceable units (FRUs) for Lenovo C2030 Touch All-In-One desktop computer.

Attention: Be sure to read and understand all the safety information before replacing any FRUs.

Notes: FRUs that have a 1 or 2 in the CRU column are Customer Replaceable Units (CRUs).

1 identifies parts that are fairly simple to replace, requiring few or no tools.

2 identifies parts that are slightly more difficult to replace.

N-identifies parts that are not to be replaced by the customer.

Item # Description Lenovo PN

BDPLANAR

C C2030 NOK I54210 UMA MB 5B20H03387

C C2030 W8P I54210 UMA MB 5B20H03325

C C2030 NOK 1G I54210 DIS MB 5B20H03374

C C2030 W8P 1G I54210 DIS MB 5B20H03313

C C2030 NOK 2G 3558 DIS MB 5B20H03369

C C2030 W8P 2G 3558 DIS MB 5B20H03308

C C2030 NOK 2957 UMA MB 5B20H03361

C C2030 W8P 2957 UMA MB 5B20H03300

C C2030 NOK 2G 2957 DIS MB 5B20H03353

C C2030 W8P 2G 2957 DIS MB 5B20H03404

C C2030 NOK 1G 3558 DIS MB 5B20H03344

C C2030 W8P 1G 3558 DIS MB 5B20H03393

C C2030 NOK 2G I34030 DIS MB 5B20H03331

C C2030 W8P 2G I34030 DIS MB 5B20H03380

C C2030 NOK 2G I54210 DIS MB 5B20H03319

C C2030 W8P 2G I54210 DIS MB 5B20H03370

C C2030 NOK 3558 UMA MB 5B20H03310

C C2030 W8P 3558 UMA MB 5B20H03363

C C2030 NOK 1G I34005 DIS MB 5B20H03302

C C2030 W8P 1G I34005 DIS MB 5B20H03354

C C2030 NOK 1G I34025 DIS MB 5B20H03296

C C2030 W8P 1G I34025 DIS MB 5B20H03349

C C2030 NOK 1G 2957 DIS MB 5B20H03400

C C2030 W8P 1G 2957 DIS MB 5B20H03337

C C2030 NOK I34030 UMA MB 5B20H03388

C C2030 W8P I34030 UMA MB 5B20H03326

N

Copyright Lenovo 2014, 2015 57

C C2030 NOK 1G I34030 DIS MB 5B20H03375

C C2030 W8P 1G I34030 DIS MB 5B20H03348

C C2030 NOK I34005 UMA MB 5B20H03299

C C2030 W8P I34005 UMA MB 5B20H03351

C C2030 NOK 2G I34005 DIS MB 5B20H03403

C C2030 W8P 2G I34005 DIS MB 5B20H03343

C C2030 NOK I34025 UMA MB 5B20H03392

C C2030 W8P I34025 UMA MB 5B20H03330

C C2030 NOK 2G I34025 DIS MB 5B20H03379

C C2030 W8P 2G I34025 DIS MB 5B20H03318

C C2030 W8S I54210 UMA MB 5B20H14343

C C2030 W8S 1G I54210 DIS MB 5B20H14364

C C2030 W8S 2G 3558 DIS MB 5B20H14354

C C2030 W8S 2957 UMA MB 5B20H14342

C C2030 W8S 2G 2957 DIS MB 5B20H14362

C C2030 W8S 1G 3558 DIS MB 5B20H14352

C C2030 W8S 2G I34030 DIS MB 5B20H14341

C C2030 W8S 2G I54210 DIS MB 5B20H14363

C C2030 W8S 3558 MB 5B20H14351

C C2030 W8S 1G I34005 DIS MB 5B20H14340

C C2030 W8S 1G I34025 DIS MB 5B20H14361

C C2030 W8S 1G 2957 DIS MB 5B20H14353

C C2030 W8S I34030 UMA MB 5B20H14366

C C2030 W8S 1G I34030 DIS MB 5B20H14356

C C2030 W8S I34005 UMA MB 5B20H14346

C C2030 W8S 2G I34005 DIS MB 5B20H14365

C C2030 W8S I34025 UMA MB 5B20H14355

C C2030 W8S 2G I34025 DIS MB 5B20H14345

CARDPOP

Converter Board C C2030 5C50H03402

Power Board C C2030 5C50H03382

N

MECHANICAL

Shielding DDR C C2030 TS 5M20H03297

MB EMIShield C C2030 5M20H03367

Thermal PAD C C2030 DIS 5M20H03359

N

STAND

Stand C C2030 BLK 5SE0H03320

Stand C C2030 WHT 5SE0H03399

N

SPEAKERINT

Speaker C C2030 L+R 5SB0H03338 N

58 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

BRACKET

BRACKET HDD C C2030 500G 5B40H03317

BRACKET HDD C C2030 1T 5B40H03368

BRACKET ODD C C2030 5B40H03401

Bracket Camera C C2030 5B40H03321

N

CABLE

LVDS Cable C C2030 TS 5C10H03381

CABLE HDD SATA C C2030 5C10H03306

CABLE ODD SATA C C2030 5C10H03350

Power Board C C2030 FFC 5C10H03357

Antenna C C2030 Main+AUX 5A30H03395

N

COVER

Bezel ODD C C2030 BLK 5CB0H03358

Bezel ODD C C2030 WHT 5CB0H03298

Stand Cap C C2030 BLK 5CB0H03334

Stand Cap C C2030 WHT 5CB0H03327

Rear Cover C C2030 UMA N-ODD BLK 5CB0H03377

Rear Cover C C2030 UMA N-ODD WHT 5CB0H03314

Rear Cover C C2030 UMA ODD BLK 5CB0H03365

Rear Cover C C2030 UMA ODD WHT 5CB0H03304

Rear Cover C C2030 DIS N-ODD BLK 5CB0H03356

Rear Cover C C2030 DIS N-ODD WHT 5CB0H03406

Rear Cover C C2030 DIS ODD BLK 5CB0H03345

Rear Cover C C2030 DIS ODD WHT 5CB0H03394

N

DISPLAY

LCD Module C C2030 Ofilm TS BLK 5D10H03332

LCD Module C C2030 Ofilm TS WHT 5D10H03390

LCD Module C C2030 TPK TS BLK 5D10H03339

LCD Module C C2030 TPK TS WHT 5D10H03385

N

FAN

FAN System C C20-30 UMA Delta 5F10G81031

FAN System C C20-30 UMA Sunon 5F10G81035

FAN System C C20-30 DIS Delta 5F10G81037

FAN System C C20-30 DIS Sunon 5F10G81032

N

HEATSINK

HEATSINK C C20-30 DIS Avc 5H40G81036

HEATSINK C C20-30 DIS CM 5H40G81029

HEATSINK C C20-30 UMA Avc 5H40G81033

HEATSINK C C20-30 UMA CM 5H40G81039

N

Chapter 9. FRU lists 59

POWER

Delta ADP-65FD BE 65W adapter 36200352

Liteon PA-1650-72IA 65W adapter 36200353

ADP-90XD BD 54Y8917

PA-1900-72FA 54Y8917

1

HDD

WD XL500A WD5000AAKX-08U6AA0 500G HDD 16200544

Toshiba Mars DT01ACA050 500G HDD 16200512

ST Pharaoh 4K Non-MC ST500DM002 500GHDD 16200674

WD XL1000B WD10EZEX-08M2NA0 1TB HDD 16200613

Toshiba Mars DT01ACA100 1TB HDD 16200513

ST Grenada BP2 ST1000DM003 1TB HDD 16200688

N

ODD

PSN UJ8FB Slim Tray Rambo w/o bezel 25215310

HLDS GUB0N Slim Tray Rambo w/o bezel 00FC442

PLDS DU-8A5SH Tray Rambo w/o bezel LSOPU 25214499

PLDS DU-8A6SH Tray Rambo w/o bezel 00FC442

N

RAM

HMT425S6AFR6A-PB 2GB D3L-1600S Memory-HF 1100643

MT4KTF25664HZ-1G6E1 2GB D3L-1600S Memory 1100956

Mic_R D9PSH 2GB D3L-1600S Memory-HF 1100965

M471B5173DB0-YK0 4GB D3L-1600S Memory-HF 1100942

HMT451S6BFR8A-PB 4GB D3L-1600S Memory-HF 1100985

HMT451S6AFR8A-PB 1100638

MT8KTF51264HZ-1G6E1 4GB D3L-1600S Memory-HF 1100957

Mic_R D9QBJ 4GB D3L-1600S Memory-HF 1100967

M471B5674QH0-YK0 2GB D3L-1600S Memory-HF 1100983

M471B5173DB0-YK0 4GB D3L-1600S Memory-HF 1100942

HMT425S6AFR6A-PB 2GB D3L-1600S Memory-HF 1100643

HMT451S6BFR8A-PB 4GB D3L-1600S Memory-HF 1100985

Mic_R D9PSH 2GB D3L-1600S Memory-HF 1100965

Mic_R D9QBJ 4GB D3L-1600S Memory-HF 1100967

M471B1G73DB0-YK0 8GB D3L-1600S Memory-HF 1100943

HMT41GS6BFR8A-PB 8GB D3L-1600S Memory-HF 1100986

HMT41GS6AFR8A-PB 1100634

MT16KTF1G64HZ-1G6E1 1100635

Mic_R D9QBJ 8GB D3L-1600S Memory-HF 1101012

N

60 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Wifi Combo

Liteon WB335 1x1BGN+BT4.0 HMC 20200437

CBT RTL8723BE 1x1BN+BT4.0 PCIE HMC 20200440

LTN RTL8821AE 1x1ac+BT4.0 Combo HMC 11202485

CBT RTL8821AE 1x1ac BT combo HMC 20200571

N

Camera

AVC 720P 5821 Hi162 WB 1DM S Cam 20200643

Bison 720P 5840 Hi162 WB 1DM S Cam 20200644

LT 720P 5840 Hi162 WB 1DM S Cam 20200667

N

KB & Mouse

Liteon LXH-SM-8825 Black Silk Mouse-LVT 25200528

Chicony LXH-MSU-1111 Black Silk Mouse-LVT 25200529

Sunrex LXH-EMS-10ZA Black Silk Mouse-LVT 25200530

Liteon LXH-SM-8825 W-Silk Mouse 25201068

Sunrex LXH-EMS-10ZA W-Silk Mouse 25201322

Liteon SM-8861(WW) Mouse Black 25203464

Liteon SM-8861 Mouse(No Battery) Black 25203465

Liteon SM-8861 Mouse(MY) Black 25203466

Liteon SM-8861(JP) Mouse-Black 25205773

Liteon SM-8861(WW) 2.4G Mouse White 25211016

Liteon SM-8861 2.4G Mouse(No Battery)WTE 25211017

Liteon SM-8861 2.4G Mouse(MY) White 25211018

Liteon SM-8861 2.4G Mouse(JP) White 25211019

Sunrex EKB-10YA(US) B-Silk USB KB-LVT8 25209111

Primax KB4721(US) B-Silk USB KB-LVT8 25209112

Sunrex EKB-10YA(TW) B-Silk USB KB-LVT8 25209114

Sunrex EKB-10YA(TH) B-Silk USB KB-LVT8 25209115

Sunrex EKB-10YA(CZ-SL) B-S USB KB-LVT8 25209116

Sunrex EKB-10YA(IN) B-Silk USB KB-LVT8 25209117

Sunrex EKB-10YA(RU) B-Silk USB KB-LVT8 25209118

Sunrex EKB-10YA(UK) B-Silk USB KB-LVT8 25209119

Sunrex EKB-10YA(Nordic) B-S USB KB-LVT8 25209120

Sunrex EKB-10YA(LA) B-Silk USB KB-LVT8 25209121

Sunrex EKB-10YA(AR) B-Silk USB KB-LVT8 25209122

Sunrex EKB-10YA(SW) B-Silk USB KB-LVT8 25209123

Sunrex EKB-10YA(GE) B-Silk USB KB-LVT8 25209124

Sunrex EKB-10YA(TR) B-Silk USB KB-LVT8 25209125

Sunrex EKB-10YA(SP) B-Silk USB KB-LVT8 25209126

Sunrex EKB-10YA(SL) B-Silk USB KB-LVT8 25209127

Sunrex EKB-10YA(IT) B-Silk USB KB-LVT8 25209128

1

Chapter 9. FRU lists 61

Sunrex EKB-10YA(HB) B-Silk USB KB-LVT8 25209129

Sunrex EKB-10YA(FR) B-Silk USB KB-LVT8 25209130

Sunrex EKB-10YA(GK) B-Silk USB KB-LVT8 25209131

Sunrex EKB-10YA(HG) B-Silk USB KB-LVT8 25209132

Sunrex EKB-10YA(BG) B-Silk USB KB-LVT8 25209133

Sunrex EKB-10YA(HR) B-Silk USB KB-LVT8 25209134

Sunrex EKB-10YA(JP) B-Silk USB KB-LVT8 25209135

Sunrex EKB-10YA(EN-FR) B-S USB KB-LVT8 25209136

Sunrex EKB-10YA(PT) B-Silk USB KB-LVT8 25209137

Sunrex EKB-10YA(BE-EN) B-S USB KB-LVT8 25209138

Sunrex EKB-10YA(DU) B-S USB KB-LVT8 25209139

Sunrex EKB-10YA(US) W-Silk USB KB-LVT8 25209145

Primax KB4721(US) W-Silk USB KB-LVT8 25209146

Sunrex EKB-10YA(TW) W-Silk USB KB-LVT8 25209147

Sunrex EKB-10YA(TH) W-Silk USB KB-LVT8 25209148

Sunrex EKB-10YA(CZ-SL) W-S USB KB-LVT8 25209149

Sunrex EKB-10YA(IN) W-Silk USB KB-LVT8 25209150

Sunrex EKB-10YA(RU) W-Silk USB KB-LVT8 25209151

Sunrex EKB-10YA(UK) W-Silk USB KB-LVT8 25209152

Sunrex EKB-10YA(Nordic) W-S USB KB-LVT8 25209153

Sunrex EKB-10YA(LA) W-Silk USB KB-LVT8 25209154

Sunrex EKB-10YA(AR) W-Silk USB KB-LVT8 25209155

Sunrex EKB-10YA(SW) W-Silk USB KB-LVT8 25209156

Sunrex EKB-10YA(GE) W-Silk USB KB-LVT8 25209157

Sunrex EKB-10YA(TR) W-Silk USB KB-LVT8 25209158

Sunrex EKB-10YA(SP) W-Silk USB KB-LVT8 25209159

Sunrex EKB-10YA(SL) W-Silk USB KB-LVT8 25209160

Sunrex EKB-10YA(IT) W-Silk USB KB-LVT8 25209161

Sunrex EKB-10YA(HB) W-Silk USB KB-LVT8 25209162

Sunrex EKB-10YA(FR) W-Silk USB KB-LVT8 25209163

Sunrex EKB-10YA(GK) W-Silk USB KB-LVT8 25209164

Sunrex EKB-10YA(HG) W-Silk USB KB-LVT8 25209165

Sunrex EKB-10YA(BG) W-Silk USB KB-LVT8 25209166

Sunrex EKB-10YA(HR) W-Silk USB KB-LVT8 25209167

Sunrex EKB-10YA(JP) W-Silk USB KB-LVT8 25209168

Sunrex EKB-10YA(EN-FR) W-S USB KB-LVT8 25209169

Sunrex EKB-10YA(PT) W-Silk USB KB-LVT8 25209170

Sunrex EKB-10YA(BE-EN) W-S USB KB-LVT8 25209171

Sunrex EKB-10YA(DU) W-S USB KB-LVT8 25209172

Liteon SK-8861(US) 2.4G KB-Black8 25209175

62 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Liteon SK-8861(US-MY) 2.4G KB-Black8 25209176

Liteon SK-8861(TW) 2.4G KB-Black8 25209177

Liteon SK-8861(TH) 2.4G KB-Black8 25209178

Liteon SK-8861(CS-SK) 2.4G KB-Black8 25209179

Liteon SK-8861(US-IN) 2.4G KB-Black8 25209180

Liteon SK-8861(RU) 2.4G KB-Black8 25209181

Liteon SK-8861(GB) 2.4G KB-Black8 25209182

Liteon SK-8861(Nordic) 2.4G KB-Black8 25209183

Liteon SK-8861(LA) 2.4G KB-Black8 25209184

Liteon SK-8861(LA-AR) 2.4G KB-Black8 25209185

Liteon SK-8861(SA) 2.4G KB-Black8 25209186

Liteon SK-8861(CH) 2.4G KB-Black8 25209187

Liteon SK-8861(DE) 2.4G KB-Black8 25209188

Liteon SK-8861(TR) 2.4G KB-Black8 25209189

Liteon SK-8861(ES) 2.4G KB-Black8 25209190

Liteon SK-8861(SL) 2.4G KB-Black8 25209191

Liteon SK-8861(IT) 2.4G KB-Black8 25209192

Liteon SK-8861(IL) 2.4G KB-Black8 25209193

Liteon SK-8861(FR) 2.4G KB-Black8 25209194

Liteon SK-8861(GR) 2.4G KB-Black8 25209195

Liteon SK-8861(HU) 2.4G KB-Black8 25209196

Liteon SK-8861(BG) 2.4G KB-Black8 25209197

Liteon SK-8861(KR) 2.4G KB-Black8 25209198

Liteon SK-8861(JP) 2.4G KB-Black8 25209199

Liteon SK-8861(EN-FR) 2.4G KB-Black8 25209200

Liteon SK-8861(PT) 2.4G KB-Black8 25209201

Liteon SK-8861(BE-EN) 2.4G KB-Black8 25209202

Liteon SK-8861(DU) 2.4G KB-Black8 25209203

Liteon SK-8861(US) 2.4G KB-White8 25210987

Liteon SK-8861(US-MY) 2.4G KB-White8 25210988

Liteon SK-8861(TW) 2.4G KB-White8 25210989

Liteon SK-8861(TH) 2.4G KB-White8 25210990

Liteon SK-8861(CS-SK) 2.4G KB-White8 25210991

Liteon SK-8861(US-IN) 2.4G KB-White8 25210992

Liteon SK-8861(RU) 2.4G KB-White8 25210993

Liteon SK-8861(GB) 2.4G KB-White8 25210994

Liteon SK-8861(Nordic) 2.4G KB-White8 25210995

Liteon SK-8861(LA) 2.4G KB-White8 25210996

Liteon SK-8861(LA-AR) 2.4G KB-White8 25210997

Liteon SK-8861(SA) 2.4G KB-White8 25210998

Chapter 9. FRU lists 63

Liteon SK-8861(CH) 2.4G KB-White8 25210999

Liteon SK-8861(DE) 2.4G KB-White8 25211000

Liteon SK-8861(TR) 2.4G KB-White8 25211001

Liteon SK-8861(ES) 2.4G KB-White8 25211002

Liteon SK-8861(SL) 2.4G KB-White8 25211003

Liteon SK-8861(IT) 2.4G KB-White8 25211004

Liteon SK-8861(IL) 2.4G KB-White8 25211005

Liteon SK-8861(FR) 2.4G KB-White8 25211006

Liteon SK-8861(GR) 2.4G KB-White8 25211007

Liteon SK-8861(HU) 2.4G KB-White8 25211008

Liteon SK-8861(BG) 2.4G KB-White8 25211009

Liteon SK-8861(KR) 2.4G KB-White8 25211010

Liteon SK-8861(JP) 2.4G KB-White8 25211011

Liteon SK-8861(EN-FR) 2.4G KB-White8 25211012

Liteon SK-8861(PT) 2.4G KB-White8 25211013

Liteon SK-8861(BE-EN) 2.4G KB-White8 25211014

Liteon SK-8861(US-EU) 2.4G KB-White8 25211015

Power Cord

Longwell B LAck single head 1.0M 3wire ULCSA Power Cord 31033857

Volex 1.0M C5 US Power Cord 31033858

Luxshare 1.0M C5 US Power Cord 31049517

Longwell B LAck single head 1.0M SAA Power Cord 31035397

Volex 1.0M C5 Macao Power Cord 31049500

Luxshare 1.0M C5 Macao Power Cord 31049520

Longwell 1.0M C5 2pin Japan Power Cord 31503423

Volex 1.0M C5 2pin Japan Power Cord 31503424

Luxshare 1.0M C5 2pin Japan Power Cord 31503425

Grandsun B LAck single head 1.0M 3wire CCC Power Cord(R) 31032953

Luxshare 1.0M C5 CCC Power Cord 31045147

Volex 1.0M C5 UK Power Cord 31049496

Luxshare 1.0M C5 UK Power Cord 31503352

Longwell B LAck single head 1.0M ASTA Power Cord 31035396

Longwell B LAck single head 1.0M VDE Power Cord 31035332

Volex 1.0M C5 Europe Power Cord 31049497

Luxshare 1.0M C5 Europe Power Cord 31049518

Longwell B LAck single head 1.0M India Power Cord 31035395

Luxshare 1.0M C5 India Power Cord 31503353

Longwell B LAck single head 1.0M Italy C5 Power Cord 31039104

Luxshare 1.0M C5 Italy Power Cord 31503359

Volex 1.0M C5 Italy Power Cord 31049504

1

64 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Longwell B LAck single head 1.0M Brazil Power Cord 31035828

Luxshare 1.0M C5 Brazil Power Cord 31503357

Volex 1.0M C5 Brazil Power Cord 31049505

Longwell B LAck single head 1.0M Argentina C5 Power Cord 31039100

Luxshare 1.0M C5 LA Power Cord 31503356

Volex 1.0M C5 LA Power Cord 31049507

Longwell B LAck single head 1.0M Denmark C5 Power Cord 31039101

Luxshare 1.0M C5 Denmark Power Cord 31503360

Volex 1.0M C5 Denmark Power Cord 31049503

Longwell B LAck single head 1.0M Switzer LAnd C5 Power Cord 31039103

Luxshare 1.0M C5 Switzer LAnd Power Cord 31503361

Volex 1.0M C5 Switzer LAnd Power Cord 31049508

Longwell B LAck single head 1.0M Israel C5 Power Cord 31039107

Luxshare 1.0M C5 Israel Power Cord 31503362

Volex 1.0M C5 Israel Power Cord 31049502

Longwell B LAck single head 1.0M Taiwan C5 Power Cord 31038885

Luxshare 1.0M C5 Taiwan Power Cord 31503354

Volex 1.0M C5 Taiwan Power Cord 31049499

Longwell B LAck single head 1.0M Korea C5 Power Cord 31039106

Luxshare 1.0M C5 Korea Power Cord 31503358

Volex 1.0M C5 Korea Power Cord 31049498

Longwell B LAck single head 1.0M SA C5 Power Cord 31039105

Luxshare 1.0M C5 South Africa Power Cord 31503355

Volex 1.0M C5 South Africa Power Cord 31049501

Chapter 9. FRU lists 65

66 Lenovo C20 Series Non-Touch All-In-One PC Hardware Maintenance Manual

Chapter 10. Additional Service Information

This chapter provides additional information that the service representative might find helpful.

Power management

Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors.

Advanced configuration and power interface (ACPI) BIOS

As this computer has an ACPI BIOS system, the operating system is allowed to control the power management features of the computer and the settings for Advanced Power Management (APM) BIOS mode is ignored. Not all operating systems support ACPI BIOS mode.

Automatic Power-On features

The Automatic Power-On features within the P

Manualsnet FAQs

If you want to find out how the C20-05 Lenovo works, you can view and download the Lenovo C20-05 Computer User Guide on the Manualsnet website.

Yes, we have the User Guide for Lenovo C20-05 as well as other Lenovo manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Guide should include all the details that are needed to use a Lenovo C20-05. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Lenovo C20-05 Computer User Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Lenovo C20-05 Computer User Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Lenovo C20-05 Computer User Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Lenovo C20-05 Computer User Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Lenovo C20-05 Computer User Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.