Lenovo C225 Computer Hardware Maintenance Manual PDF

1 of 60
1 of 60

Summary of Content for Lenovo C225 Computer Hardware Maintenance Manual PDF

Contents

i

Contents

Chapter 1. About this manual ................................................ 1

Important Safety Information ......................................................................1

Important information about replacing RoHS compliant FRUs ..2

Chapter 2. Safety information ................................................ 3 General safety .......................................................................................................3 Electrical safety ....................................................................................................4 Safety inspection guide ...................................................................................6 Handling electrostatic discharge-sensitive devices .........................7 Grounding requirements ...............................................................................7 Safety notices ........................................................................................................8

Chapter 3. General information ...........................................11 Specifications ..................................................................................................... 11

Chapter 4. General Checkout ...............................................12 Problem determination tips ...................................................................... 13

Chapter 5. Using the Setup Utility ......................................14 Starting the Setup Utility program ......................................................... 14 Viewing and changing settings ................................................................ 14 Using passwords .............................................................................................. 15 Using Device ...................................................................................................... 17 Selecting a startup device ........................................................................... 18 Exiting from the Setup Utility program ................................................ 19

Chapter 6. Symptom-to-FRU Index.....................................20 Hard disk drive boot error ........................................................................... 20 Power Supply Problems ................................................................................ 21

Hardware Maintenance Manual

ii

POST error codes ............................................................................................. 22 Undetermined problems ............................................................................. 23

Chapter 7. Locations ...............................................................24 Locating components and connectors ................................................. 24

Chapter 8. Replacing hardware ...........................................30 General information ....................................................................................... 30 Replacing a memory module .................................................................... 31 Removing the computer stand ................................................................. 33 Removing the computer cover ................................................................. 34 Removing the computer rear deco ......................................................... 35 Replacing the hard disk drive .................................................................... 36 Replacing the optical drive ......................................................................... 37 Replacing the converter board ................................................................. 39 Replacing the LED touch panel control module .............................. 40 Replacing the function board .................................................................... 41 Replacing the LED board ............................................................................. 42 Removing the motherboard cover ......................................................... 43 Replacing the system fan ............................................................................. 44 Replacing the heatsink .................................................................................. 45 Replacing the WLAN card ........................................................................... 46 Replacing the TV tuner card ....................................................................... 47 Replacing the speakers system ................................................................. 48 Replacing the motherboard ....................................................................... 49 Replacing the LED panel .............................................................................. 50 Replacing the camera .................................................................................... 52 Replacing the keyboard ............................................................................... 53 Replacing the mouse ..................................................................................... 54 Replacing the power adapter .................................................................... 55

Chapter 9. Additional Service Information .......................56 Power management ...................................................................................... 56

Appendix. Statement .............................................................57 Declaration .......................................................................................................... 57 Trademarks ......................................................................................................... 58

Chapter 1. About this manual

1

About this manual 1 This manual contains service and reference information for Lenovo C205 computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products.

Before servicing a Lenovo product, be sure to read the Safety Information.

The description of the TV card in this manual is only used for the machines which have the TV card. It is invalid for those machines which do not have TV card.

Important Safety Information

Be sure to read all caution and danger statements in this book before performing any of the instructions.

Veuillez lire toutes les consignes de type DANGER et ATTENTION du prsent document avant dexcuter les instructions.

Lesen Sie unbedingt alle Hinweise vom Typ ACHTUNG oder VORSICHT in dieser Dokumentation, bevor Sie irgendwelche Vorgnge durchfhren

Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel manuale prima di eseguire una qualsiasi delle istruzioni

Certifique-se de ler todas as instrues de cuidado e perigo neste manual antes de executar qualquer uma das instrues

Es importante que lea todas las declaraciones de precaucin y de peligro de este manual antes de seguir las instrucciones.

Hardware Maintenance Manual

2

Important information about replacing RoHS compliant FRUs

RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.

So, if the parts are not compliant originally, replacement parts can also be noncompliant, but in all cases, if the parts are compliant, the replacement parts must also be compliant.

Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovos requirements and schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant parts.

RoHS compliant Lenovo C205 parts have unique FRU part numbers. Before or after June, 2006, failed RoHS compliant parts must always be replaced using RoHS compliant FRUs, so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs can be used.

Products marketed before June 2006 Products marketed after June 2006 Current or original part

Replacement FRU

Current or original part

Replacement FRU

Non-RoHS Can be Non-RoHS Must be RoHS Must be RoHS Non-RoHS Can be RoHS Non-RoHS Can sub to RoHS RoHS Must be RoHS

Note: A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of order.

Related Web URLs are: Lenovo information for Suppliers website: http://www-03.ibm.com/procurement/proweb.nsf/ ContentDocsByTitle/United+States~Information+for+suppliers RoHS Directive: http://europa.eu.int/eur-lex/pri/en/oj/dat/2003/l_037/ l_03720030213en00190023.pdf California Senate Bills 20, 50: http://www.ciwmb.ca.gov/HHW/Events/AnnualConf/2004/ presentation/MPaparian.pdf

Chapter 2. Safety information

3

Safety information 2 This chapter contains the safety information that you need to be familiar with before servicing a computer.

General safety

Follow these rules to ensure general safety: Observe good housekeeping in the area of the machines during and after maintenance. When lifting any heavy object: 1. Ensure you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you

attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action

removes the strain from the muscles in your back. Do not attempt to lift any objects that weigh more than 16 kg (35 lb) or objects that you think are too heavy for you.

Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe. Before you start the machine, ensure that other service representatives and the customers personnel are not in a hazardous position. Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the machine. Keep your tool case away from walk areas so that other people will not trip over it. Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it. Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately 8 centimeters (3 inches) from the end. Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing. Remember: Metal objects are good electrical conductors.

Hardware Maintenance Manual

4

Wear safety glasses when you are: hammering, drilling soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes. After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective. Reinstall all covers correctly before returning the machine to the customer.

Electrical safety

CAUTION: Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the server/workstation covers, unless instructed otherwise in the installation and configuration procedures.

Observe the following rules when working on electrical equipment.

Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents.

Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.

Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly. Do not work alone under hazardous conditions or near equipment that has hazardous voltages. Disconnect all power before: Performing a mechanical inspection Working near power supplies Removing or installing main units Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.

Chapter 2. Safety information

5

If you need to work on a machine that has exposed electrical circuits, observe the following precautions: Ensure that another person, familiar with the power-off controls, is

near you. Remember: Another person must be there to switch off the power, if necessary.

Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back. Remember: There must be a complete circuit to cause electrical shock. By observing the above rule, you may prevent a current from passing through your body.

When using testers, set the controls correctly and use the approved probe leads and accessories for that tester.

Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames. Observe the special safety precautions when you work with very high voltages; these instructions are in the safety sections of maintenance information. Use extreme care when measuring high voltages.

Regularly inspect and maintain your electrical hand tools for safe operational condition. Do not use worn or broken tools and testers. Never assume that power has been disconnected from a circuit. First, check that it has been powered-off. Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. Do not service the following parts with the power on when they are removed from their normal operating places in a machine: Power supply units Pumps Blowers and fans Motor generators and similar units. (This practice ensures correct grounding of the units.) If an electrical accident occurs: Use caution; do not become a victim yourself. Switch off power. Send another person to get medical aid.

Hardware Maintenance Manual

6

Safety inspection guide

The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury. This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of features or options not covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present: Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock). Explosive hazards, such as a damaged CRT face or bulging capacitor Mechanical hazards, such as loose or missing hardware

The guide consists of a series of steps presented in a checklist. Begin the checks with the power off, and the power cord disconnected.

Checklist: 1. Check exterior covers for damage (loose, broken, or sharp edges). 2. Power-off the computer. Disconnect the power cord. 3. Check the power cord for:

a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and frame ground.

b. The power cord should be the appropriate type as specified in the parts listings.

c. Insulation must not be frayed or worn. 4. Remove the cover. 5. Check for any obvious alterations. Use good judgment as to the safety

of any alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal

filings, contamination, water or other liquids, or signs of fire or smoke damage.

7. Check for worn, frayed, or pinched cables. 8. Check that the power-supply cover fasteners (screws or rivets) have not

been removed or tampered with.

Chapter 2. Safety information

7

Handling electrostatic discharge-sensitive devices

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.

Notes: 1. Use product-specific ESD procedures when they exceed the

requirements noted here. 2. Make sure that the ESD protective devices you use have been certified

(ISO 9000) as fully effective.

When handling ESD-sensitive parts: Keep the parts in protective packages until they are inserted into the product. Avoid contact with other people. Wear a grounded wrist strap against your skin to eliminate static on your body. Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices. Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.

Note: The use of a grounding system is desirable but not required to protect against ESD damage.

Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.

Use an ESD common ground or reference point when working on a double-insulated or battery-operated system. You can use coax or connector-outside shells on these systems.

Use the round ground-prong of the ac plug on ac-operated computers.

Grounding requirements

Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.

Hardware Maintenance Manual

8

Safety notices

The caution and danger safety notices in this section are provided in the the language of English.

DANGER Electrical current from power, telephone and communication cables is hazardous.

To avoid a shock hazard: Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. Connect all power cords to a properly wired and grounded electrical outlet. Connect to properly wired outlets any equipment that will be attached to this product. When possible, use one hand only to connect or disconnect signal cables. Never turn on any equipment when there is evidence of fire, water, or structural damage. Disconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures. Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.

To Connect To Disconnect 1. Turn everything OFF. 2. First, attach all cables to devices. 3. Attach signal cables to

connectors. 4. Attach power cords to outlet. 5. Turn device ON.

1. Turn everything OFF. 2. First, remove power cords from

outlet. 3. Remove signal cables from

connectors. 4. Remove all cables from devices.

CAUTION: When replacing the lithium battery, use only Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your

Chapter 2. Safety information

9

system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.

Do not: Throw or immerse into water Heat to more than 100C (212F) Repair or disassemble

Dispose of the battery as required by local ordinances or regulations.

CAUTION: When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or transmitters) are installed, note the following:

Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

DANGER: Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following: Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.

Hardware Maintenance Manual

10

CAUTION: Use safe practices when lifting.

CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.

1

2

CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices.

Chapter 3. General information

11

General information 3 This chapter provides general information that applies to all machine types supported by this publication.

Specifications

This section lists the physical specifications for your computer.

Type Lenovo C205

This section lists the physical specifications.

Environment Air temperature:

Operating: 10 to 35C Transit: -20 to 55C

Humidity: Operating: 35% to 80% Transit: 20% to 93% (40C) Altitude: 86KPa to 106KPa

Electrical input Input voltage: 100~240VAC 10% Input frequency: 50Hz & 60Hz

Hardware Maintenance Manual

12

General Checkout 4 The drives in the computer you are servicing might have been rearranged or the drive startup sequence changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or programs can be overwritten if you select an incorrect drive.

Attention

General error messages appear if a problem or conflict is found by an application program, the operating system, or both. For an explanation of these messages, refer to the information supplied with that software package.

Notes

Thedefaultisforthiscomputertobootupinquietmode(no memory count and checkpoint code display) when no errors are detected by POST.

BeforereplacinganyFRUs,ensurethatthelatestlevelofBIOSis installed on the system. A down-level BIOS might cause false errors and unnecessary replacement of the motherboard.

Use the following procedures to help determine the cause of the problem: 1. Power-off the computer and all external devices. 2. Check all cables and power cords. 3. Set all display controls to the middle position. 4. Power-on all external devices. 5. Power-on the computer.

Lookfordisplayederrorcodes Lookforreadableinstructionsoramainmenuonthedisplay. If you did not receive the correct response, proceed to step 6. If you do receive the correct response, proceed to step 7.

Chapter 4. General Checkout

13

6. Look at the following conditions and follow the instructions: IfthecomputerdisplaysaPOSTerror,gotoPOST error codes. Ifthecomputerhangsandnoerrorisdisplayed,continueatstep7.

7. If you cannot continue, replace the last device tested.

Problem determination tips Due to the variety of hardware and software combinations that can be encountered, use the following information to assist you in problem determination. If possible, have this information available when requesting assistance from Service Support and Engineering functions.

Machine type and model Processor or hard disk drive upgrades Failure symptom Do diagnostics indicate a failure? What, when, where, single, or multiple systems? Is the failure repeatable? Has this configuration ever worked? If it has been working, what changes were made prior to it failing? Is this the original reported failure? Diagnostics version Type and version level Hardware configuration Print (print screen) configuration currently in use BIOS level Operating system software Type and version level

Note: To eliminate confusion, identical systems are considered identical only if they: 1. Are the exact machine type and models 2. Have the same BIOS level 3. Have the same adapters/attachments in the same locations 4. Have the same address jumpers/terminators/cabling 5. Have the same software versions and levels 6. Have the same configuration options set in the system 7. Have the same setup for the operation system control files

Comparing the configuration and software set-up between working and non-working systems will often lead to problem resolution.

Hardware Maintenance Manual

14

Using the Setup Utility 5 The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating-system settings might override any similar settings in the Setup Utility program.

Starting the Setup Utility program

To start the Setup Utility program, do the following:

1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer.

2. Press and hold the F1 key then turn on the computer. When you see the setup screen, release the F1 key.

Notes: a. If you are using a USB keyboard and the Setup Utility program does

not display using this method, repeatedly press and release the F1 key rather than leaving it pressed when turning on the computer.

b. If a Power-On Password or an administrator password has been set, the Setup Utility program menu is not displayed until you type your password. For more information, see Using passwords.

Viewing and changing settings

The Setup Utility program menu lists items that identify system configuration topics. To view or change settings, see Starting the Setup Utility program.

When working with the Setup Utility program menu, you must use the keyboard. The keys used to perform various tasks are displayed on the right side of each screen.

Chapter 5. Using the Setup Utility

15

Using passwords

By using the Setup Utility program, you can set passwords to prevent unauthorized persons from gaining access to your computer and data. See Starting the Setup Utility program. The following types of passwords are available:

AdministratorPassword Power-OnPassword

You do not have to set any passwords to use your computer. However, if you decide to set any passwords, read the following sections.

Password considerations A password can be any combination of up to 16 characters (a-z and 0-9) and symbols; . For security reasons, it is a good idea to use a strong password that cannot be easily compromised. We suggest the passwords should adhere to the following rules:

Musthaveatleastsevencharactersinlength Containatleastonealphabeticcharacterandonenumericcharacter SetupUtilityprogramandharddiskdrivepasswordsarenotcase

sensitive Notbeyournameoryourusername Notbeacommonwordoracommonname Besignificantlydifferentfromyourpreviouspassword

Administrator password When an Administrator Password is set, it deters unauthorized persons from changing configuration settings. If you are responsible for maintaining the settings of several computers, you might want to set a Administrator Password.

After you set an Administrator Password, a password prompt is displayed each time you try to access the Setup Utility program.

If both the Administrator and Power-On Password are set, you can type either password. However, to change any configuration settings, you must use your Administrator password.

Hardware Maintenance Manual

16

Setting, changing, and deleting a Administrator password To set, change, or delete a password, do the following:

Note

A password can be any combination of up to 16 characters (a-z, 0-9 and ;). For more information, see Password considerations on page 17.

1. Start the Setup Utility program (see Starting the Setup Utility program on page 16).

2. From Security menu, select Set Administrator Password and press Enter.

3. The password dialog box will be displayed. Type the new password, and press Enter.

4. when prompted to confirm the password, type the password again. If you type the password correctly, the password will be installed.

To delete a previously set Administrator password, do the following :

Note: When prompted for a password, you must type your Administrator password.

1. From Security menu, select Set Administrator Password and press Enter.

2. The password dialog box will be displayed. Enter New Password and confirm New Password dialog. A setup notice will display that changes have been saved.

3. Select Exit. 4. Select Save changes and Exit.

Power-On Password When a Power-On Password is set, you cannot start the Setup Utility program until a valid password is typed from the keyboard.

Setting, changing, and deleting a Power-On Password To set, change, or delete a Power-On Password, do the following:

Note

A password can be any combination of up to 16 characters (a-z, 0-9 and ;).

1. Start the Setup Utility program (See Starting the Setup Utility program.) 2. From the Security menu, selet Set Power-On Password and press Enter.

Chapter 5. Using the Setup Utility

17

3. The password dialog box will be displayed. Type the new password, and press Enter.

4. when prompted to confirm the password, type the password again. If you type the password correctly, the password will be installed.

To delete a previously set Power-On Password, do the following :

1. From the Security menu, select Set Power-On Password and press Enter.

2. The password dialog box will be displayed. Enter New Password and confirm New Password dialog. A setup notice will display that changes have been saved.

3. Select Exit. 4. Select Save changes and Exit. After the password is set, you may select the Advanced Menu for device setup.

Using Device

Device is used to enable or disable user access to the following device ATA Drives Setup Select this option to configure your

systems SATA mode.

To set Device, do the following:

1. Start the Setup Utility program (see Starting the Setup Utility program on page 16).

2. From the Setup Utility program menu, select Devices. 3. Select ATA Drives Setup. 4. Select IDE or AHCI and press Enter to set the SATA mode. 5. Return to the Setup Utility program menu and press F10 to save

configuration changes and exit setup.

Note

If you do not want to save the settings, select Exit and select Discard changes and Exit.You can set others such as Audio Setup and Network Setup. See the information displayed on the right side of the screen.

Hardware Maintenance Manual

18

Selecting a startup device

If your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device.

Selecting a temporary startup device Use this procedure to startup from any boot device.

Note: Not all CDs, hard disks, and diskettes are bootable.

1. Turn off your computer. 2. Press and hold the F12 key then turn on the computer. When the

Startup Device Menu appears, release the F12 key.

Note: If you are using a USB keyboard and the Startup Device Menu does not display using this method, repeatedly press and release the F12 key rather than leaving it pressed when turning on the computer.

3. Select the desired startup device from the Startup Device Menu and press Enter to begin.

Note: Selecting a startup device from the Startup Device menu does not permanently change the startup sequence.

Selecting or changing the startup device sequence To view or permanently change the configured startup device sequence, do the following:

1. Start the Setup Utility program (see Starting the Setup Utility program on page 16).

2. Select Start Up. 3. Select Quick Boot Mode, Numlock, Keyboardless Operation to set these

devices. 4. Select Disabled or Enabled and press Enter. 5. Press ESC to return to Exit and select Save changes and Exit.

If you have changed these settings and want to return to the default settings, select Load Optimal Defaults on the Setup Utility menu.

Chapter 5. Using the Setup Utility

19

Exiting from the Setup Utility program

When you finish viewing or changing settings, press Esc to return to the Setup Utility program menu (you might have to press Esc several times). If you want to save the new settings, select Save changes and Exit before you exit. Otherwise, your changes will not be saved.

Hardware Maintenance Manual

20

Symptom-to-FRU Index 6 The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first. Always begin with Chapter 4, General Checkout, on page 13. This index can also be used to help you decide which FRUs to have available when servicing a computer. If you are unable to correct the problem using this index, go to Undetermined problems on page 25.

Notes

Ifyouhavebothanerrormessageandanincorrectaudioresponse diagnose the error message first.

Ifyoucannotrunthediagnostictestsoryougetadiagnosticerror code when running a test but did receive a POST error message diagnose the POST error message first.

Ifyoudidnotreceiveanyerrormessagelookforadescriptionof your error symptoms in the first part of this index.

Hard disk drive boot error

A hard disk drive boot error can have the following causes.

Error FRU/Action

The start-up drive is not in the boot sequence in configuration.

Check the configuration and ensure the start-up drive is in the boot sequence.

No operating system installed on the boot drive.

Install an operating system on the boot drive.

Chapter 6. Symptom-to-FRU Index

21

Error FRU/Action

The boot sector on the start-up drive is corrupted.

The drive must be formatted do the following: 1. Attempt to back-up the data on

the failing hard disk drive. 2. Using the operating systems

programs format the hard disk drive.

The drive is defective. Replace the hard disk drive.

Power Supply Problems

If you suspect a power problem, use the following procedures.

Check/Verify FRU/Action Check the following for proper installation.

Power Cord On/Off Switch connector On/Off Switch Power Supply connector Motherboard Power Supply connectors Microprocessor(s) connection

Reseat connectors

Check the power cord for continuity. Power Cord Check the power-on switch for continuity.

Power-on Switch

Hardware Maintenance Manual

22

POST error codes

Each time you power-on the system, it performs a series of tests that check the operation of the system and some options. This series of tests is called the Power-On Self-Test, or POST. POST does the following operations.

Checkssomebasicmotherboardoperations Checksthememoryoperation Startsthevideooperation Verifiesthatthebootdriveisworking

If the POST detects a problem, an error message appears on the screen. A single problem can cause several error messages to appear. When you correct the cause of the first error message, the other error messages probably will not appear on the screen the next time you turn on the system.

POST Error Message Description/Action CMOS Date/Time Not Set The CMOS Date and/or Time are

invalid. This error can be resolved by readjusting the system time in Phenix BIOS Setup.

CMOS Checksum Bad Checksum of CMOS is incorrect. The computer loads the default configuration settings. This error might indicate that CMOS has become corrupt due to a weak CMOS battery.

Primary Master Hard Disk Error The IDE/ATAPI device configured as Primary Master/Secondary Master could not be found or initialized. Make sure the hard disk drive is correctly installed.

Secondary Master Hard Disk Error

Keyboard error Cannot initialize the keyboard. Make sure the keyboard is properly connected to the computer and that no keys are held pressed during POST. To purposely configure the computer without a keyboard, set keyboardless operation in Setup to Enable. The BIOS then ignores the missing keyboard during POST.

Chapter 6. Symptom-to-FRU Index

23

POST Error Message Description/Action System Halted The system has been halted. A reset

or power cycle is required to reboot the machine. This message appears after a fatal error has been detected.

Reboot and Select proper Boot device or Insert Boot Media in selected Boot device

The BIOS was unable to find a suitable boot device. Make sure the boot drive is properly connected to the computer. Make sure you have bootable media.

Undetermined problems

If this computer has a parallel ATA hard disk drive, make sure that the hard disk drive is jumpered as a master and the optical drive is jumpered as a slave. 1. Power-off the computer. 2. Remove or disconnect the following components (if installed) one at a

time. a. External devices (modem, printer, or mouse) b. Any adapters c. Memory modules d. Extended video memory e. Hard disk drive

3. Power-on the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or adapter.

If all devices and adapters have been removed, and the problem continues, replace the motherboard.

Hardware Maintenance Manual

24

Locations 7 This section provides illustrations to help locate the various connectors, controls and components of the computer.

Locating components and connectors The following illustrations will help you to locate the various components and connectors in your computer.

Font view The following illustration shows the location of connectors on the front of the computer.

1

6 7 8 93 4 5

2

Chapter 7. Locations

25

1 Built-in microphone

2 Camera

3 Hard disk drive indicator

4 Wireless LAN card indicator

5 LED ON/OFF indicator (When turning on the LED, the indicator light will be off; when turning off the LED, the indicator light will be solid on.)

6 Brightness down

7 Brightness up

8 LED ON/OFF

9 Power button

Left and right view The following illustrations show the location of connectors on the left and right side of the computer.

Attention

Be careful not to block any air vents on the computer. Blocked air vents may cause overheating.

1 5

4 3 2

1 Memory card reader

2 USB ports (2)

Hardware Maintenance Manual

26

3 Headphone connector

4 Microphone connector

5 Optical drive slot

Rear view The following illustration shows the location of connectors on the rear of the computer.

1

2

3

45

1 USB ports (3)

2 Ethernet connector

3 PS/2 keyboard connector

4 Power connector

5 TV tuner connector (Selected models only)

Chapter 7. Locations

27

Internal components The following illustration shows the components inside your computer.

1 Computer stand

2 Rear deco

3 Computer cover

4 Motherboard Cover

5 Hard disk drive

6 Motherboard

7 Chassis

8 LED panel

9 Front bezel

10 System fan

11 Heatsink

12 Optical drive

13 LED touch panel control module

Hardware Maintenance Manual

28

14 Connverter board

15 Front LED indicator control module

16 Camera

17 Function board

18 Speakers

19 TV antenna connector

Identifying parts on the motherboard The motherboard (sometimes called the planar or system board) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are factory-installed or that you can install later.

The following illustration shows the locations of parts on the motherboard.

1

2

3

3

789101112131415

16

18

17

19

20

21 22

23

4 5 6

1 Memory module connector

2 Card reader connector

3 USB connectors

4 TV tuner card connector

Chapter 7. Locations

29

5 Headphone connector

6 Microphone connector

7 L/R speakers connector

8 USB connectors

9 Ethernet connector

10 PS/2 keyboard connector

11 Power connector

12 Front LCD Logo connector

13 LED touch panel control module connector

14 Optical disk drive power connector

15 Optical disk drive data connector

16 Hard disk drive power and data connectors

17 Front LED indicator control module connector

18 Function board connector

19 Converter connector

20 System fan connector

21 Camera connector

22 LED connector

23 WLAN card connector

Hardware Maintenance Manual

30

Replacing hardware 8 Attention

Do not remove the computer cover or attempt any repair before reading the Important safety information in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support web site at: http://consumersupport.lenovo.com.

Note

Use only parts provided by Lenovo.

General information

Pre-disassembly instructions Before proceeding with the disassembly procedure, make sure that you do the following:

1. Turn off the power to the system and all peripherals.

2. Unplug all power and signal cables from the computer.

3. Place the system on a flat, stable surface.

Chapter 8. Replacing hardware

31

Replacing a memory module

Attention

Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the computer cover.

Note

It helps to place the computer face down on a soft, flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.

1. Remove any media (disks, CDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

2. Unplug all power cords from electrical outlets.

3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Locating connectors on the rear of the computer.

4. Remove the protective rubber cap . 5. Remove the screw that secures the memory cover to the computer

chassis .

Hardware Maintenance Manual

32

6. Lift up the memory cover .

7. Push out the latches on both sides of the memory socket to release the memory module and gently pull the memory module upward to remove it from its socket . Both memory modules can be removed by following the same procedure.

8. Align the new memory module with the socket, then insert it and push down on the top edge. Make sure the latches lock the memory module in place.

9. Align then slide back the memory cover.

10. Screw the memory cover back.

11. Place the protective rubber cap back in position.

Chapter 8. Replacing hardware

33

Removing the computer stand

Attention

Turn off the computer and wait 3 to 5 minutes to let the it cool down before removing the computer stand.

To remove the computer stand:

Note

It helps to place the computer face down on a soft, flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.

1. Remove any media (diskettes, CDs, or memory cards) from the drives,

shut down your operating system, and turn off the computer and all

attached devices. 2. Unplug all power cords from electrical outlets.

3. Disconnect all cables attached to the computer. This includes power

cords, input/output (I/O) cables, and any other cables that are

connected to the computer. Refer to Locating connectors on the rear

of the computer. 4. Place the computer upside down on the flat surface.

5. Remove the 2 screws that secure the computer stand to the computer

chassis.

Hardware Maintenance Manual

34

6. Slide the computer stand out.

Removing the computer cover

To remove the computer cover: 1. Remove the computer stand. Refer to Removing the computer stand.

2. Lift up the computer cover.

Chapter 8. Replacing hardware

35

Removing the computer rear deco

To remove the computer rear deco 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the 2 screws that secure the rear deco to the chassis.

4. Lift up the computer rear deco to remove it.

Hardware Maintenance Manual

36

Replacing the hard disk drive

To replace the hard disk drive 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the 4 screws that secure the stand bracket to the chassis, then lift it up.

4. Remove the 4 screws that secure the hard disk drive bay to the chassis.

5. Slide the hard disk drive bay out, then lift it up.

Chapter 8. Replacing hardware

37

6. Remove the 4 screws that secure the hard disk drive to the drive bay. Slide the hard disk drive out of the drive bay.

7. Install the new hard disk drive.

(1.) Insert the new hard disk drive into the drive bay.

(2.) Slide the new hard disk back into position, then secure it to the disk bay with the 4 screws.

8. Align then slide the hard disk drive bay back into position and secure it to the chassis with the 4 screws!

9. Put the stand bracket back into place and secure it to the chassis with its 4 screws.

10. Reattach the computer cover and stand.

Replacing the optical drive

To replace the optical drive 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the screw that secures the optical drive to the chassis.

4. Disconnect the data and power cables from the optical drive.

5. Slide the optical drive out of the drive bay.

Hardware Maintenance Manual

38

6. Push a small iron stick (e.g.a paper clip) into the small hole on the

optical drive cover so that the disk springs out as shown.

7. Remove the 2 screws that secure the optical drive to the metal bracket.

8. Use a small flat head screwdriver to press the pins down, then push the

pins out against the cover. 9. Separate the cover from the defective optical drive.

10. Install the new optical drive as follows:

(1) Align the new optical drive with the cover, then push the cover back into position.

(2) Screw the metal bracket onto the new optical drive.

(3) Slide the new optical drive into the drive bay.

Chapter 8. Replacing hardware

39

11. Screw the new optical drive back onto the chassis.

12. Reattach the computer cover and stand.

Replacing the converter board

To replace the converter board 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the 2 screws that secure the converter board to the chassis.

4. Lift up the converter board and disconnect the power cables from the converter board.

5. Separate the converter board from the insulating box.

6. Slide the new converter board into the insulating box. 7. Connect the power cables to the new converter board.

8. Align then screw in the new converter board to the chassis.

9. Reattach the computer cover and stand.

Hardware Maintenance Manual

40

Replacing the LED touch panel control module

To replace the LED touch panel control module 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the rear deco. Refer to Removing the rear deco.

4. Remove the 2 screws that secure the LED touch panel control module to the chassis.

5. Disconnect the cables from the LED touch panel control module and remove it.

6. Connect the cables to the new LED touch panel control module.

7. Align then screw in the new LED touch panel control module.

8. Install back the rear deco.

9. Reattach the computer cover and stand.

Chapter 8. Replacing hardware

41

Replacing the function board

To replace the function board 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the 3 screws that secure the function board to the chassis.

4. Disconnect the cable from the function board.

5. Lift up the function board to remove it.

6. Connect the cable to the new function board.

7. Align then screw in the new function board.

8. Reattach the computer cover and stand.

Hardware Maintenance Manual

42

Replacing the LED board

To replace the LED board 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the 2 screws that secure the LED board to the chassis.

4. Disconnect the cable from the LED board.

5. Lift up the LED board to remove it.

6. Connect the cable to the new LED board.

7. Align then screw in the new LED board.

8. Reattach the computer cover and stand.

Chapter 8. Replacing hardware

43

Removing the motherboard cover

To remove the motherboard cover 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the 7 screws that secure the motherboard cover to the chassis.

4. Lift up the motherboard cover.

Hardware Maintenance Manual

44

Replacing the system fan

To replace the system fan 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the motherboard cover. Refer to Removing the motherboard cover.

4. Remove the 4 screws that secure the stand bracket to the chassis, then lift it up.

5. Disconnect the system fan power cable from the connector on the motherboard.

6. Remove the 3 screws that secure the system fan to the chassis.

7. Lift up the system fan to remove it.

Chapter 8. Replacing hardware

45

8. Align the 3 screw holes on the new system fan with the 3 mounting

holes on the chassis. Screw in the 3 screws and attach the power cable

to the connector on the motherboard.

9. Reattach the motherboard cover and stand bracket for the computer

stand.

10. Reattach the computer cover and stand.

Replacing the heatsink

To replace the heatsink 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the motherboard cover. Refer to Removing the motherboard cover.

4. Remove the rear deco. Refer to Removing the rear deco.

5. Remove the 8 screws that secure the heatsink to the motherboard.

6. Lift up the heatsink to remove it.

7. Align the 8 screw holes on the new heatsink with the mounting holes on the motherboard. Screw the new heatsink in.

8. Screw the motherboard cover back.

9. Install back the rear deco.

10. Reattach the computer cover and stand.

Hardware Maintenance Manual

46

Replacing the WLAN card

To replace the WLAN card 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the motherboard cover. Refer to Removing the motherboard cover.

4. Disconnect the antenna cables from the WLAN card.

5. Remove the 2 screws that secure the WLAN card to the motherboard.

6. Pull the WLAN card upward to remove it from the card port.

7. Align the new WLAN card with the card port, then insert it.

8. Screw the new WLAN card in.

9. Connect the antenna cables to the new WLAN card.

10. Reattach the motherboard cover.

11. Reattach the computer cover and stand.

Chapter 8. Replacing hardware

47

Replacing the TV tuner card

To replace the TV tuner card 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the motherboard cover. Refer to Removing the motherboard cover.

4. Disconnect the antenna cable from the TV tuner card.

5. Remove the 2 screws that secure the TV tuner card to the motherboard.

6. Pull the TV tuner card upward to remove it from the card port.

7. Align the new TV tuner card with the card port, then insert it.

8. Screw the new TV tuner card in.

9. Connect the antenna cable to the new TV tuner card.

10. Reattach the motherboard cover.

11. Reattach the computer cover and stand.

Hardware Maintenance Manual

48

Replacing the speakers system

To replace the speakers system 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the motherboard cover. Refer to Removing the motherboard cover.

4. Disconnect the speakers system cables from the motherboard.

5. Remove the 4 screws that secure the left and right speakers to the chassis.

6. Pull out the left and right speakers from the chassis.

7. Align the new speakers with the chassis, then secure them with the 4 screws.

8. Connect the speakers system cables to the motherboard.

9. Reattach the motherboard cover.

10. Reattach the computer cover and stand.

Chapter 8. Replacing hardware

49

Replacing the motherboard

To replace the motherboard 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the computer rear deco. Refer to Removing the computer rear deco

4. Remove the motherboard cover. Refer to Removing the motherboard cover.

5. Remove the memory module. Refer to Replacing a memory module.

6. Remove the heatsink. Refer to Replacing the heatsink.

7. Remove the WLAN card. Refer to Replacing the WLAN card.

8. Remove the TV tuner card. Refer to Replacing the TV tuner card.

9. Disconnect all cables connected to the motherboard.

10. Remove the 5 screws that secure the motherboard to the chassis.

11. Slide the motherboard out, then lift it up.

12. Place the new motherboard onto the chassis, then align the 5 screw holes in the motherboard with the mounting holes on the chassis.

13. Secure the new motherboard with the 5 screws.

14. Reattach all related components onto the new motherboard and reconnect all cables..

15. Reattach back the motherboard cover.

16. Reattach the computer cover and stand.

Hardware Maintenance Manual

50

Replacing the LED panel

To replace the LED panel 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the hard disk drive. Refer to Replacing the hard disk drive.

4. Remove the optical drive. Refer to Replacing the optical drive.

5. Remove the motherboard cover. Refer to Removing the motherboard cover.

6. Remove the system fan. Refer to Replacing the system fan.

7. Remove the heatsink. Refer to Replacing the heatsink.

8. Remove the speakers system. Refer to Replacing the speakers systems.

9. Remove the converter board. Replacing the converter board.

10. Remove the LED touch panel control module. Refer to Replacing the LED touch panel control module.

11. Remove the function board. Refer to Replacing the function board.

12. Remove the LED board. Refer to Replacing the LED board.

13. Remove the rear deco. Refer to Removing the computer rear deco.

14. Remove the motherboard. Refer to Replacing the motherboard.

15. Remove the 8 screws that secure the LED panel and its rear bracket to the front bezel.

16. Pull the pins out to release the LED panel, then lift it out gently.

17. Remove the 4 screws that secure the LED panel to the panel bracket, then lift it out the LED panel bracket.

18. Disconnect all cables connected to the LED panel.

Chapter 8. Replacing hardware

51

19. Lift up the LED panel to remove it.

20. Align and then install the new LED panel.

21. Reconnect all cables and reattach all related parts.

22. Reattach the computer cover and stand.

Hardware Maintenance Manual

52

Replacing the camera

To replace the camera 1. Remove the computer stand. Refer to Removing the computer stand.

2. Remove the computer cover. Refer to Removing the computer cover.

3. Remove the rear deco. Refer to Removing the computer rear deco.

4. Remove the 2 screws that secure the camera to the panel front bezel.

5. Remove the data cable from the camera.

6. Pull out the camera gently from the panel front bezel.

7. Connect the camera cable to the new camera.

8. Align and then screw in the new camera.

9. Reattach the computer rear deco and secure it to the chassis with the screws.

10. Reattach the computer cover and stand.

Chapter 8. Replacing hardware

53

Replacing the keyboard

Attention

Do not remove the computer cover or attempt any repair before reading the Important safety information in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support web site at: http://consumersupport.lenovo.com.

To replace the keyboard: 1. Remove any media (disks, CDs, or memory cards) from the drives,

shut down the operating system, and turn off the computer and all attached devices.

2. Unplug all power cords from electrical outlets.

Note

Your keyboard might be connected to the standard keyboard connector at the rear of the computer or to a USB connector on either side or at the rear of the computer.

3. Disconnect the keyboard cable from the computer and connect the new keyboard cable to the same connector.

Hardware Maintenance Manual

54

Replacing the mouse

Attention

Do not remove the computer cover or attempt any repair before reading the Important safety information in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support web site at: http://consumersupport.lenovo.com.

To replace the mouse: 1. Remove any media (disks, CDs, or memory cards) from the drives,

shut down the operating system, and turn off the computer and all attached devices.

2. Unplug all power cords from electrical outlets.

3. Disconnect the mouse cable from the computer and connect the new mouse cable to the same connector.

Chapter 8. Replacing hardware

55

Replacing the power adapter

To replace the power adapter:

1. Remove any media (disks, CDs, or memory cards) from the drives,

shut down the operating system, and turn off the computer and all

attached devices.

2. Disconnect the power adapter from the computer and connect the

new power adapter to the same connector.

Hardware Maintenance Manual

56

Additional Service Information 9

This chapter provides additional information that the service representative might find helpful.

Power management

Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors.

Automatic configuration and power interface (ACPI) BIOS

Being an ACPI BIOS system, the operating system is allowed to control the power management features of the computer and the setting for Advanced Power Management (APM) BIOS mode is ignored. Not all operating systems support ACPI BIOS mode.

Automatic Power-On features The Automatic Power-On features within the Power Management menu allow you to enable and disable features that turn on the computer automatically.

Resumes On RTC Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event or a daily event.

On LAN Wake Up: This feature allows LAN adapter card to wake the System.

Appendix. Statement

57

Statement A Declaration

Thank you for using Lenovo products.

Carefully read all documents shipped with your computer before you install and use the product for the first time. Lenovo is not responsible for any loss except when caused by installation and operations performed by Lenovo professional service personnel. You are responsible if you fail to operate the product according to instructions and requirements in the manuals included with your computer, or operate the product inappropriately.

This manual could include technical inaccuracies or typographical errors. Changes are made periodically to the information herein; these changes will be incorporated in new editions of the publication.To provide better service, Lenovo reserves the right to improve and/or modify the products and software programs described in the manuals included with your computer, and the content of the manual, at any time without additional notice.

The manuals included with your computer are provided to help you use Lenovos products appropriately. For the configuration of the product, refer to the related contract (if any) or product packing list, or consult the distributor for the product sales.

The content of the manuals included with your computer is protected by copyright laws and rules. None of the manuals included with your computer may be reproduced or transcribed by any means or translated into any language without prior written permission of Lenovo.

The software interface and function and hardware configuration described in the manuals included with your computer might not match exactly the actual configuration of the computer that you purchase.You are welcome to contact us about the manuals included with your computer. For the latest information or any questions or comments, contact or visit the Lenovo Web site: Service Web site: http://consumersupport.lenovo.com

Hardware Maintenance Manual

58

Trademarks

Lenovo and the Lenovo logo, IdeaCentre and IdeaCentre logo are trademarks of Lenovo in the United States, other countries, or both.

Microsoft, Windows, and Windows Vista are trademarks of the Microsoft group of companies.

Intel Inside is a trademark of Intel Corporation in the U.S. and/or other countries.

AMD, the AMD Arrow logo, ATI, AMD Athlon, AMD LIVE!, AMD Opteron, AMD Phenom, AMD Sempron, Catalyst, Cool n Quiet, CrossFire, PowerPlay, Radeon, and The Ultimate Visual Experience are trademarks of Advanced Micro Devices, Inc.

Other company,

Manualsnet FAQs

If you want to find out how the C225 Lenovo works, you can view and download the Lenovo C225 Computer Hardware Maintenance Manual on the Manualsnet website.

Yes, we have the Hardware Maintenance Manual for Lenovo C225 as well as other Lenovo manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Hardware Maintenance Manual should include all the details that are needed to use a Lenovo C225. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Lenovo C225 Computer Hardware Maintenance Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Lenovo C225 Computer Hardware Maintenance Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Lenovo C225 Computer Hardware Maintenance Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Lenovo C225 Computer Hardware Maintenance Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Lenovo C225 Computer Hardware Maintenance Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.