Contents

Lenovo AIO A740 Computer Hardware Maintenance Manual PDF

1 of 59
1 of 59

Summary of Content for Lenovo AIO A740 Computer Hardware Maintenance Manual PDF

Lenovo A540/A740Hardware Maintenance Manual

Machine Types: F0AN [A540];F0AM [A740]

Lenovo A540/A740 Hardware Maintenance Manual

Machine Types: F0AN [A540];F0AM [A740]

First Edition (March 2014)6th

Copyright Lenovo 2014.

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925

Contents

Chapter 1. About this manual . . . . . . 1 Important Safety Information . . . . . . . . . . 1

Chapter 2. Safety information. . . . . . 3 General safety . . . . . . . . . . . . . . . . 3 Electrical safety . . . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . . 5 Handling electrostatic discharge-sensitive devices . . . . . . . . . . . . . . . . . . 5 Grounding requirements . . . . . . . . . . . . 6 Safety notices . . . . . . . . . . . . . . . . 6

Chapter 3. General information . . . . . 9 Specifications . . . . . . . . . . . . . . . . 9

Chapter 4. General Checkout . . . . . 11

Chapter 5. Using the Setup Utility. . . 13 Starting the Lenovo BIOS Setup Utility program . 13 Viewing and changing settings . . . . . . . . 13 Using passwords. . . . . . . . . . . . . . 13 Enabling or disabling a device . . . . . . . . 15 Selecting a startup device . . . . . . . . . . 16 Exiting the Lenovo BIOS Setup Utility program . . 17

Chapter 6. Symptom-to-FRU Index . . 19 Hard disk drive boot error . . . . . . . . . . 19 Power Supply Problems . . . . . . . . . . . 19

POST error codes . . . . . . . . . . . . . 20 Undetermined problems . . . . . . . . . . . 20

Chapter 7. Replacing hardware . . . . 21 General information. . . . . . . . . . . . . 21 Replacing the keyboard and mouse . . . . . . 22 Replacing the power cord or power adapter . . . 22 Removing the base cover . . . . . . . . . . 23 Replacing the hard disk drive . . . . . . . . . 24 Replacing a memory module . . . . . . . . . 26 Replacing the system fan . . . . . . . . . . 27 Replacing the heat-sink . . . . . . . . . . . 28 Replacing the speaker system . . . . . . . . 29 Replacing the motherboard. . . . . . . . . . 30 Removing the hinge from the chassis . . . . . . 31 Removing the rear cover . . . . . . . . . . . 32 Replacing the Transform board . . . . . . . . 35 Replacing the Wi-Fi card. . . . . . . . . . . 36 Replacing the power switch board . . . . . . . 37 Replacing the NFC module . . . . . . . . . . 38 Replacing the camera . . . . . . . . . . . . 39 Replacing the LED panel. . . . . . . . . . . 40 A540 FRU lists. . . . . . . . . . . . . . . 42 A740 FRU lists. . . . . . . . . . . . . . . 46

Chapter 8. General information . . . . 53 Additional Service Information . . . . . . . . 53

Copyright Lenovo 2014 iii

iv Lenovo A540/A740Hardware Maintenance Manual

Chapter 1. About this manual

This manual contains service and reference information for Lenovo A540/A740 computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products.

Before servicing a Lenovo product, be sure to read the Safety Information.

The description of the TV-tuner card in this manual applies only to computers with a TV-tuner card installed. It does not apply to computers without a TV-tuner card.

Important Safety Information Be sure to read all CAUTION and DANGER sections in this manual before following any of the instructions.

Veuillez lire toutes les consignes de type DANGER et ATTENTION du prsent document avant dexcuter les instructions.

Lesen Sie unbedingt alle Hinweise vom Typ ACHTUNG oder VORSICHT in dieser Dokumentation, bevor Sie irgendwelche Vorgnge durchfhren

Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel manuale prima di eseguire una qualsiasi delle istruzioni

Certifique-se de ler todas as instrues de cuidado e perigo neste manual antes de executar qualquer uma das instrues

Es importante que lea todas las declaraciones de precaucin y de peligro de este manual antes de seguir las instrucciones.

Copyright Lenovo 2014 1

2 Lenovo A540/A740Hardware Maintenance Manual

Chapter 2. Safety information

This chapter contains the safety information that you need to be familiar with before servicing a computer.

General safety Follow these rules to ensure general safety:

Keep the areas around the computer clear and clean during and after maintenance.

When lifting any heavy object:

1. Ensure you can stand safely without slipping.

2. Distribute the weight of the object equally across both feet.

3. Lift slowly. Never move suddenly or twist when you attempt to lift.

4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any objects that weigh more than 16 kg (35 lb) or objects that you think are too heavy for you.

Do not perform any action that would create a hazard for the customer, or would make the computer unsafe.

Before you start the computer, ensure that other service representatives and customer personnel are not in a position that would create a hazard for them.

Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the computer.

Keep your tool case away from areas that people may walk through to ensure no-one trips over it.

Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, tie or fasten it back.

Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately 8 centimeters (3 inches) from the end.

Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing. Remember: Metal objects are good electrical conductors.

Wear safety glasses when you are: hammering, drilling soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes.

After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective.

Reattach all covers correctly before returning the computer to the customer.

Electrical safety

CAUTION: Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect any attached power cords, telecommunication cables, network cables, and modem cables before you open the computer covers, unless instructed otherwise in the installation and configuration procedures.

Copyright Lenovo 2014 3

Observe the following rules when working on electrical equipment.

Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their equipment that contain small conductive fibers to decrease electrostatic discharge.

Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.

Do not work alone under hazardous conditions or near equipment that has hazardous voltages.

Disconnect all power before:

Performing a mechanical inspection

Working near power supplies

Removing or installing Field Replaceable Units (FRUs)

Before you start to work on the computer, unplug the power cord. If you cannot unplug it, ask the customer to power-off the electrical outlet that supplies power to the machine and to lock the electrical outlet in the off position.

If you need to work on a computer that has exposed electrical circuits, observe the following precautions:

Ensure that another person, familiar with the power-off controls, is near you. Remember: Another person must be there to switch off the power, if necessary.

Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back. Remember: There must be a complete circuit to cause electrical shock. By observing the above rule, you may prevent a current from passing through your body.

When using a tester, set the controls correctly and use the approved probe leads and accessories for that tester.

Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages; these instructions are in the safety sections of the maintenance information. Use extreme care when measuring high voltages.

Regularly inspect and maintain your electrical hand tools to ensure they are safe to use.

Do not use worn or broken tools and testers.

Never assume that power has been disconnected from a circuit. First, check that it has been powered off.

Always look carefully for possible hazards in your work area. Examples of these hazards are wet floors, non-grounded power extension cables, conditions that may cause or allow power surges, and missing safety grounds.

Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. This surface is conductive, and touching a live circuit can cause personal injury and damage to the computer.

Do not service the following parts with the power on when they are removed from their normal operating positions in a computer:

Power supply units

Pumps

Blowers and fans

Motor generators

and similar units. (This practice ensures correct grounding of the units.)

If an electrical accident occurs:

Use caution; do not become a victim yourself.

4 Lenovo A540/A740Hardware Maintenance Manual

Switch off power.

Send another person to get medical aid.

Safety inspection guide The intent of this inspection guide is to assist you in identifying potential hazards posed by these products. Each computer, as it was designed and built, had required safety items installed to protect users and service personnel from injury. This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of features or options not covered by this inspection guide.

If any hazards are present, you must determine how serious the apparent hazard could be and whether you can continue without first resolving the problem.

Consider the following items and the safety hazards they present:

Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock).

Explosive hazards, such as a damaged CRT face or bulging capacitor

Mechanical hazards, such as loose or missing hardware

The guide consists of a series of steps presented as a checklist. Begin the checks with the power off, and the power cord disconnected.

Checklist:

1. Check exterior covers for damage (loose, broken, or sharp edges).

2. Power-off the computer. Disconnect the power cord.

3. Check the power cord for:

a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and frame ground.

b. The power cord should be the appropriate type as specified in the parts listings.

c. Insulation must not be frayed or worn.

4. Remove the cover.

5. Check for any obvious alterations. Use good judgment as to the safety of any alterations.

6. Check inside the unit for any obvious hazards, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.

7. Check for worn, frayed, or pinched cables.

8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.

Handling electrostatic discharge-sensitive devices Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the computer, the part, the work mat, and the person handling the part are all at the same charge.

Notes:

1. Use product-specific ESD procedures when they exceed the requirements noted here.

2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.

When handling ESD-sensitive parts:

Chapter 2. Safety information 5

Keep the parts in protective packages until they are inserted into the product.

Avoid contact with other people while handling the part.

Wear a grounded wrist strap against your skin to eliminate static on your body.

Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.

Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.

Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.

Note: The use of a grounding system is desirable but not required to protect against ESD damage.

Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.

Use an ESD common ground or reference point when working on a double-insulated or battery-operated system. You can use coax or connector-outside shells on these systems.

Use the round ground-prong of the AC plug on AC-operated computers.

Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.

Safety notices The CAUTION and DANGER safety notices in this section are provided in the the language of English.

DANGER

Electrical current from power, telephone and communication cables is hazardous.

To avoid a shock hazard:

Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.

Connect all power cords to a properly wired and grounded electrical outlet.

Connect any equipment that will be attached to this product to a properly wired outlet.

When possible, use one hand only to connect or disconnect signal cables.

Never turn on any equipment when there is evidence of fire, water, or structural damage.

Disconnect the attached power cords, telecommunications cables, network cables, and modem cables before you open the device covers, unless instructed otherwise in the installation and configuration procedures.

Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.

6 Lenovo A540/A740Hardware Maintenance Manual

To Connect To Disconnect

1. Turn everything OFF.

2. First, attach all cables to devices.

3. Attach signal cables to connectors.

4. Attach power cords to outlet.

5. Turn device ON.

1. Turn everything OFF.

2. First, remove power cords from outlets.

3. Remove signal cables from connectors.

4. Remove all cables from devices.

CAUTION: When replacing the lithium battery, use only Part Number 45C1566 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not:

Throw into or immerse in water

Heat to more than 100C (212F)

Repair or disassemble

Dispose of the battery as required by local ordinances or regulations.

CAUTION: When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or transmitters) are installed, note the following:

Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.

Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

DANGER

Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:

These diodes emit radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.

18 kg (37 lbs) 32 kg (70.5 lbs) 55 kg (121.2 lbs)

CAUTION: Use safe practices when lifting.

Chapter 2. Safety information 7

CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.

CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices.

8 Lenovo A540/A740Hardware Maintenance Manual

Chapter 3. General information

This chapter provides general information that applies to all computer models covered by this manual.

Specifications This section lists the physical specifications for your computer.

This section lists the physical specifications for your computer.

Type Lenovo A540/A740

This section lists the physical specifications.

Environment

Air temperature:

Operating: 10 to 35C

Transit: -20 to 55C

Humidity:

Operating: 35% to 80%

Transit: 20% to 90% (40C)

Altitude: 86KPa to 106KPa

Electrical input:

Input voltage: 90V-264V(AC)

Input frequency: 47Hz-63Hz

Copyright Lenovo 2014 9

10 Lenovo A540/A740Hardware Maintenance Manual

Chapter 4. General Checkout

Attention: The drives in the computer you are servicing might have been rearranged or the drive startup sequence may have been changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or programs can be overwritten if you select an incorrect drive.

General error messages appear if a problem or conflict is found by an application, the operating system, or both. For an explanation of these messages, refer to the information supplied with that software package.

Use the following procedure to help determine the cause of the problem:

1. Power-off the computer and all external devices.

2. Check all cables and power cords.

3. Set all display controls to the middle position.

4. Power-on all external devices.

5. Power-on the computer.

Look for displayed error codes.

Look for readable instructions or a main menu on the display.

If you did not receive the correct response, proceed to step 6.

If you did receive the correct response, proceed to step 7.

6. If one of the following happens, follow the instruction given:

If the computer displays a POST error, go to POST error codes.

If the computer hangs and no error is displayed, continue at step 7.

7. If the test stops and you cannot continue, replace the last device tested.

Copyright Lenovo 2014 11

12 Lenovo A540/A740Hardware Maintenance Manual

Chapter 5. Using the Setup Utility

The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating system settings might override any similar settings in the Setup Utility program.

Starting the Lenovo BIOS Setup Utility program To start the Lenovo BIOS Setup Utility program, do the following:

1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer.

2. Press and hold the F1 key then turn on the computer. When the Lenovo BIOS Setup Utility program is displayed, release the F1 key.

Note: If a Power-On Password or an Administrator Password has been set, the Setup Utility program menu will not be displayed until you type your password. For more information, see Using passwords.

Viewing and changing settings System configuration options are listed in the Lenovo BIOS Setup Utility program menu. To view or change settings, see Starting the Setup Utility program.

You must use the keyboard when using the Lenovo BIOS Setup Utility menu. The keys used to perform various tasks are displayed on the bottom of each screen.

Using passwords You can use the Lenovo BIOS Setup Utility program to set passwords to prevent unauthorized persons from gaining access to your computer and data. See Starting the Setup Utility program. The following types of passwords are available:

Administrator Password

Power-On Password

You do not have to set any passwords to use your computer. However, if you decide to set passwords, read the following sections.

Password considerations

A password can be any combination of letters and numbers up to 16 characters (a-z and 0-9). For security reasons, it is a good idea to use a strong password that cannot be easily compromised. We suggest that passwords should follow these rules:

For a strong password, use 7-16 characters and a mix of letters and numbers.

Do not use your name or your user name.

Do not use a common word or a common name.

Use something significantly different from your previous password.

Attention: Administrator and Power-On passwords are not case sensitive.

Copyright Lenovo 2014 13

Administrator Password

Setting an Administrator Password deters unauthorized persons from changing configuration settings. You might want to set an Administrator Password if you are responsible for maintaining the settings of several computers.

After you set an Administrator Password, a password prompt is displayed every time you access the Lenovo BIOS Setup Utility program.

If both the Administrator and Power-On Password are set, you can type either password. However, you must use your Administrator Password to change any configuration settings.

Setting, changing, or deleting an Administrator password

To set an Administrator Password, do the following:

Note: A password can be any combination of letters and numbers up to 16 characters (a-z and 0-9). For more information, see Password considerations on page 13.

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Security menu, select Set Administrator Password and press the Enter key.

3. The password dialog box will be displayed. Type the password then press the Enter key.

4. Re-type the password to confirm, then press the Enter key. If you typed the password correctly, the password will be installed.

To change an Administrator Password, do the following:

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Security menu, select Set Administrator Password and press the Enter key.

3. The password dialog box will be displayed. Type the current password then press the Enter key.

4. Type the new password, then press the Enter key. Re-type the password to confirm the new password. If you typed the new password correctly, the new password will be installed. A Setup Noticed confirming that changes have been saved will be displayed.

To delete a previously set Administrator Password, do the following :

1. From the Security menu, select Set Administrator Password and press the Enter key.

2. The password dialog box will be displayed. Type the current password and press the Enter key.

3. To delete an Administrator Password, leave each new password line item blank, then press the Enter key. A Setup Notice confirming that changes have been saved will be displayed.

4. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

5. Select Save changes and Exit from the menu.

Power-On Password

When a Power-On Password is set, you cannot start the Lenovo BIOS Setup Utility program until a valid password is typed from the keyboard.

Setting, changing, or deleting a Power-On Password

Note: A password can be any combination of letters and numbers up to 16 characters (a-z and 0-9).

14 Lenovo A540/A740Hardware Maintenance Manual

To set a Power-On Password, do the following:

1. Start the Lenovo BIOS Setup Utility program (See Starting the Lenovo BIOS Setup Utility program on page 13.)

2. From the Security menu, select Set Power-On Password and press the Enter key.

3. The password dialog box will be displayed. Type the password, then press the Enter key.

4. Re-type the password to confirm. If you typed the password correctly, the password will be installed.

To change a Power-On Password, do the following:

1. Start the Lenovo BIOS Setup Utility program (See Starting the Lenovo BIOS Setup Utility program on page 13.)

2. From the Security menu, select Set Power-On Password and press the Enter key.

3. The password dialog box will be displayed. Type the current password then press the Enter key.

4. Type the new password, then press the Enter key. Re-type the password to confirm the new password. If you typed the new password correctly, the new password will be installed. A Setup Noticed confirming that changes have been saved will be displayed.

To delete a previously set Power-On Password, do the following :

1. From the Security menu, select Set Power-On Password and press the Enter key.

2. The password dialog box will be displayed. Type the current password and press the Enter key.

3. To delete the Power-On Password, leave each new password line item blank, then press Enter. A Setup Notice confirming that changes have been saved will be displayed.

4. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

5. Select Save changes and Exit from the menu.

Enabling or disabling a device The Devices options is used to enable or disable user access to the following devices:

USB Functions Select whether to enable or disable USB (Universal Serial Bus) functions. If the functions are disabled, no USB devices can be used.

SATA Mode When this feature is set to Disabled, all devices connected to the SATA connectors (e.g. hard disk drives or the optical disk drive) are disabled and cannot be accessed.

Onboard Audio Controller Select whether to enable or disable the Onboard Audio Controller. When this feature is set to Disabled all devices connected to the audio connectors (e.g. headphones or a microphone) are disabled and cannot be used.

Onboard Ethernet Controller or LAN Boot Agent Select whether to enable or disable theOnboard Ethernet Controller, or select whether to enable or disable load onboard PXE (Preboot Execution Environment).

To enable or disable a device, do the following:

1. Start the Setup Utility program (see Starting the Setup Utility program on page 13).

2. From the Setup Utility program menu, select Devices.

3. Select an option as follows:

Select USB Setup, press the Enter key, then select USB Functions.

Chapter 5. Using the Setup Utility 15

Select ATA Device Setup, press the Enter key, then select SATA Mode.

Select Audio Setup, press the Enter key, then select Onboard Audio Controller.

Select Network Setup, press the Enter key, then select Onboard Ethernet Support or LAN Boot Agent.

4. Select Disabled or Enabled and press the Enter key.

5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

6. Select Save changes and Exit from the menu.

Notes:

a. If you do not want to save the settings, select Discard changes and Exit from the menu.

b. Select IDE/AHCI Mode: Device driver support is required for ACHI. Depending on how the hard disk image was installed, changing this setting may prevent the system from booting.

Selecting a startup device If your computer does not boot from a device such as the CD/DVD-ROM drive disk or hard disk as expected, follow one of the procedures below.

Selecting a temporary startup device

Use this procedure to start up from any boot device.

Note: Not all CDs, DVDs or hard disk drives are bootable.

1. Turn off your computer.

2. Press and hold the F12 key then turn on the computer. When the Startup Device Menu appears, release the F12 key.

Note: If the Startup Device Menu does not display using these steps, repeatedly press and release the F12 key rather than keeping it pressed when turning on the computer.

3. Use and arrows to select the desired startup device from the Startup Device Menu and press the Enter key to begin.

Note: Selecting a startup device from the Startup Device Menu does not permanently change the startup sequence.

Selecting or changing the startup device sequence

To view or permanently change the configured startup device sequence, do the following:

1. Start the Lenovo BIOS Setup Utility program (see Starting the Lenovo BIOS Setup Utility program on page 13).

2. From the Lenovo BIOS Setup Utility program main menu, select the Startup option.

3. Press the Enter key, and select the devices for the Primary Boot Sequence. Read the information displayed on the right side of the screen.

4. Use - and arrows to select a device. Use the <+> or <-> keys to move a device up or down. Use the <> key to exclude the device from or include the device in the boot sequence.

5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option.

6. Select Save changes and Exit from the menu.

Notes:

16 Lenovo A540/A740Hardware Maintenance Manual

a. If you do not want to save the settings, select Discard changes and Exit from the menu.

b. If you have changed these settings and want to return to the default settings, select Load Optimal Defaults from the menu.

Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. You might have to press the Esc key several times. Do one of the following:

If you want to save the new settings, select Save changes and Exit from the menu. When the Save & reset window shows, select the Yes button, and then press the Enter key to exit the Lenovo BIOS Setup Utility program.

If you do not want to save the settings, select Discard changes and Exit from the menu. When the Reset Without Saving window shows, select the Yes button, and then press the Enter key to exit the Lenovo BIOS Setup Utility program.

Chapter 5. Using the Setup Utility 17

18 Lenovo A540/A740Hardware Maintenance Manual

Chapter 6. Symptom-to-FRU Index

The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first. Always begin with Chapter 4, General Checkout, on page 11. This index can also be used to help you decide which FRUs to have available when servicing a computer. If you are unable to correct the problem using this index, go to Undetermined problems on page 20.

Notes:

If you have both an error message and an incorrect audio response, diagnose the error message first.

If you cannot run the diagnostic tests or you get a diagnostic error code when running a test but did receive a POST error message, diagnose the POST error message first.

If you did not receive any error message look for a description of your error symptoms in the first part of this index.

Hard disk drive boot error A hard disk drive boot error can be caused by the following.

Error FRU/Action

The startup drive is not included in the boot sequence configuration.

Check the configuration and ensure the startup drive is in the boot sequence.

No operating system is installed on the boot drive. Install an operating system on the boot drive.

The boot sector on the startup drive is corrupted. The drive must be formatted. Do the following:

1. Attempt to back up the data on the failing hard disk drive.

2. Use the operating system to format the hard disk drive.

The drive is defective. Replace the hard disk drive.

Power Supply Problems Follow these procedures if you suspect there is a power supply problem.

Check/Verify FRU/Action

Check that the following are properly installed:

Power Cord

On/Off Switch connector

System Board Power Supply connectors

Microprocessor connections

Reseat connectors

Check the power cord. Power Cord

Check the power-on switch. Power-on Switch

Copyright Lenovo 2014 19

POST error codes Each time you turn the computer on, it performs a series of tests to check that the system is operating correctly and that certain options are set. This series of tests is called the Power-On Self-Test, or POST. POST does the following:

Checks some basic motherboard operations

Checks that the memory is working correctly

Starts video operations

Verifies that the boot drive is working

POST Error Message Description/Action

Keyboard error Cannot initialize the keyboard. Make sure the keyboard is properly connected to the computer and that no keys are held pressed during POST. To purposely configure the computer without a keyboard, select Keyboardless operation in Startup and set the option to Enabled. The BIOS then ignores the missing keyboard during POST.

Reboot and Select proper Boot device or Insert Boot Media in selected Boot device

The BIOS was unable to find a suitable boot device. Make sure the boot drive is properly connected to the computer. Make sure you have bootable media in the boot device.

Undetermined problems 1. Power-off the computer.

2. Remove or disconnect the following components (if connected or installed) one at a time.

a. External devices (modem, printer, or mouse)

b. Extended video memory

c. External Cache

d. External Cache RAM

e. Hard disk drive

f. Disk drive

3. Power-on the computer to re-test the system.

4. Repeat steps 1 through 3 until you find the failing device or component.

If all devices and components have been removed and the problem continues, replace the system board.

20 Lenovo A540/A740Hardware Maintenance Manual

Chapter 7. Replacing hardware

Attention: Do not remove the computer cover or attempt any repair before reading the Important safety information in the Safety and Warranty Guide that was included with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at: http://consumersupport.lenovo.com.

Note: Use only parts provided by Lenovo.

General information Pre-disassembly instructions

Before starting the disassembly procedure, make sure that you do the following:

1. Turn off the power to the system and all peripherals.

2. Unplug all power and signal cables from the computer.

3. Place the system on a flat, stable surface.

Copyright Lenovo 2014 21

Replacing the keyboard and mouse Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the keyboard and mouse

Step 1. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Note: Your keyboard will be connected to a USB connector on one side or at the rear of the computer.

Step 4. Disconnect the defective keyboard cable from the computer and connect the new keyboard cable to the same connector.

Note: The mouse can be replaced using the same method.

Replacing the power cord or power adapter Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the power cord and power adapter:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

22 Lenovo A540/A740Hardware Maintenance Manual

Step 2. Locate the connector for the power cord. Refer to Rear view.

Step 3. Disconnect the failing power cord and adapter from the computer and connect the new power cord and adapter to the same connector.

Removing the base cover Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

To remove the base cover

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Place the computer face-down on a soft flat surface, then remove the 8 screws that secure the base cover to the base.

Chapter 7. Replacing hardware 23

Step 5. Return the computer to an upright position, then lift the base cover up and slide it out as shown.

Step 6. To reattach the base cover:

a. Line up the base cover with the base, slide it back and snap it into position.

b. Place the computer face-down on a soft flat surface, then secure the base cover to the base with the 8 screws.

Replacing the hard disk drive Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the hard disk drive

Step 1. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

24 Lenovo A540/A740Hardware Maintenance Manual

Step 5. Remove the 4 screws that secure the hard disk drive to the motherboard.

Step 6. Disconnect the data and power cable from the hard disk drive.

Chapter 7. Replacing hardware 25

Step 7. Remove the 4 screws that secure the hard disk drive to the bracket, then separate the hard disk drive from the bracket.

Step 8. Install the new hard disk drive as follows:

a. Secure the new hard disk drive to the brackets with the 4 screws.

b. Connect the data and power cable to the new hard disk drive and motherboard.

c. Secure the new hard disk drive to chassis with the 2 screws.

Step 9. Reattach the base cover and secure it with the screws.

Replacing a memory module Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace a memory module

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

26 Lenovo A540/A740Hardware Maintenance Manual

Step 5. Push out the latches on both sides of the memory socket to release the memory module. Gently pull the memory module upward to remove it from its socket.

Step 6. Align the new memory module with the memory socket, then insert it and push down on the top edge. Make sure the latches lock the memory module in place.

Step 7. Reattach the base cover and secure it with the screws.

Replacing the system fan Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the system fan

Step 1. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Remove the 3 screws that secure the system fan to the heat-sink.

Step 6. Disconnect the power cable from the motherboard.

Chapter 7. Replacing hardware 27

Step 7. Lift the system fan up to remove it.

Step 8. Line up the new system fan, then secure it to the heat-sink and connect the new power cable to the motherboard.

Step 9. Reattach the base cover and secure it with the screws.

Replacing the heat-sink Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the heat-sink:

Step 1. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Remove the system fan. Refer to Replacing the system fan.

Step 6. Remove the 8 screws that secure the heat-sink to the motherboard.

28 Lenovo A540/A740Hardware Maintenance Manual

Step 7. Remove the heat-sink by lifting it up.

Attention: Place the heat-sink upside down on a flat surface to prevent thermal grease from contaminating other components.

Attention: Use an alcohol pad to wipe the thermal grease off the heat-sink and CPU.

Step 8. Use a thermal grease syringe to place 5 drops of grease on the top of the microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the grease syringe).

Step 9. Line up the new heat-sink then secure it to the motherboard with the 8 screws.

Step 10. Attach the system fan to the new heat-sink and secure it with the screws.

Step 11. Reattach the base cover and secure it with the screws.

Replacing the speaker system Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the speaker system:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Disconnect the speaker cable from the connectors on the motherboard.

Chapter 7. Replacing hardware 29

Step 6. Remove the 4 screws that secure the speaker system to the motherboard.

Step 7. Detach the speaker from the chassis.

Step 8. To install the new speaker system:

a. Attach the new speaker cable to the chassis and secure it with the 4 screws.

b. Connect the new speaker cable to the motherboard.

Step 9. Reattach the base cover and secure it with the screws.

Replacing the motherboard Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the motherboard:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Remove a memory module. Refer to Replacing a memory module.

Step 6. Remove the system fan. Refer to Replacing the system fan.

Step 7. Remove the heat-sink. Refer to Replacing the heat-sink.

Step 8. Remove all the cables connected to the motherboard.

30 Lenovo A540/A740Hardware Maintenance Manual

Step 9. Remove the 3 screws that secure the motherboard to the chassis and slide it out as shown.

Step 10. To install the new motherboard:

a. Install the memory module to the connector on the new motherboard.

b. Line up the new motherboard with the chassis and slide it into position. Align the holes on the new motherboard with the mounting holes on the chassis and secure it to the chassis with the screws.

c. Connect all the cables to the new motherboard.

Step 11. Reattach the base cover and secure it with the screws.

Removing the hinge from the chassis Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To remove the hinge from the chassis

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Chapter 7. Replacing hardware 31

Step 5. Disconnect the touch and LED panel cables from the connectors on the motherboard.

Step 6. Remove the 6 screws that secure the hinge to the chassis 1 , then raise the hinge to remove it from the chassis. 2

1

2

Step 7. To reattach the hinge to the chassis:

a. Line up the hinge with the chassis and slide the hinge into position.

b. Secure the hinge to the chassis with the 6 screws.

c. Reconnect the touch and LED panel cables to the motherboard.

Step 8. Reattach the base cover and secure it with the screws.

Removing the rear cover Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To remove the rear cover

32 Lenovo A540/A740Hardware Maintenance Manual

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Remove the hinge from the chassis. Refer to Removing the hinge from the chassis.

Step 6. Remove the 2 screws that secure the LED panel to the rear cover.

Chapter 7. Replacing hardware 33

Step 7. Slide the LED panel upward from the bottom (with Lenovo logo) of the panel.

34 Lenovo A540/A740Hardware Maintenance Manual

Step 8. Open up the LED panel from the bottom 1 , remove the 2 screws that secure the transform board to the rear cover 2 , and then disconnect the 2 cables from the transform board. 3

Step 9. Then separate the rear cover from the LED panel.

Step 10. To reattach the rear cover:

a. Line up the LED panel with the rear cover, reconnect the LVDS1 and LVDS2 cables to the transform board.

b. Reattach the transform board, and secure it to the rear cover with the 2 screws.

c. Line up the LED panel with mounting pins on the rear cover, and then slide it into position.

Step 11. Reattach the hinge to the chassis, and reconnect the touch and LED panel cables back to the motherboard.

Step 12. Reattach the base cover and secure it with the screws.

Replacing the Transform board Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the transform board

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Remove the hinge from the chassis. Refer to Removing the hinge from the chassis.

Chapter 7. Replacing hardware 35

Step 6. Remove the rear cover. Refer to Removing the rear cover.

Step 7. Remove the 2 screws that secure the transform board to the rear cover, and then lift it up to remove it.

Step 8. Disconnect all the cables from the transform board.

Step 9. Lift up the Wi-Fi card to remove it from the transform board.

Step 10. To install the new transform board:

a. Install the Wi-Fi card to the new transform board.

b. Connect all the cables to the new transform board.

c. Secure the transform board to the rear cover with the screws.

Step 11. Reattach the rear cover to the LED panel.

Step 12. Reattach the hinge to the chassis, and reconnect the touch and LED panel cables back to the motherboard.

Step 13. Reattach the base cover and secure it with the screws.

Replacing the Wi-Fi card Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the Wi-Fi card:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

36 Lenovo A540/A740Hardware Maintenance Manual

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Remove the hinge from the chassis. Refer to Removing the hinge from the chassis.

Step 6. Remove the rear cover. Refer to Removing the rear cover.

Step 7. Lift up the Wi-Fi card to remove it from the socket.

Step 8. Disconnect the antenna cable and data cable from the Wi-Fi card.

Step 9. To install the new Wi-Fi card:

a. Connect the antenna cable to the new Wi-Fi card.

b. Line up the new Wi-Fi card with the socket, snap it into position and secure it with the pins.

Step 10. Reattach the rear cover to the LED panel.

Step 11. Reattach the hinge to the chassis, and reconnect the touch and LED panel cables to the motherboard.

Step 12. Reattach the base cover and secure it with the screws.

Replacing the power switch board Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the power switch board

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Chapter 7. Replacing hardware 37

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Remove the hinge from the chassis. Refer to Removing the hinge from the chassis.

Step 6. Remove the rear cover. Refer to Removing the rear cover.

Step 7. Remove the 4 screws that secure the power switch board to the rear cover and then release the power switch board from the locking pin.

Step 8. Disconnect the power cable from the power switch board.

Step 9. To install the power switch board:

a. Connect the power cable to the new converter board.

b. Line up the hole on the new power switch board with the mounting hole on the rear cover and secure it with the screw.

Step 10. Reattach the rear cover to the LED panel.

Step 11. Reattach the hinge to the chassis, and reconnect the touch and LED panel cables to the motherboard.

Step 12. Reattach the base cover and secure it with the screws.

Replacing the NFC module Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the Bluetooth module:

38 Lenovo A540/A740Hardware Maintenance Manual

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Remove the hinge from the chassis. Refer to Removing the hinge from the chassis.

Step 6. Remove the rear cover. Refer to Removing the rear cover.

Step 7. Disconnect the cable from the NFC module.

Step 8. The NFC module is glued to the rear cover, using a flat head screw driver gently to remove the module from the rear cover.

Step 9. To install the new NFC module:

a. Connect the cable to the new NFC module.

b. Line up the new NFC module with the socket, snap it into position.

Step 10. Reattach the rear cover to the LED panel.

Step 11. Reattach the hinge to the chassis, and reconnect the touch and LED panel cables to the motherboard.

Step 12. Reattach the base cover and secure it with the screws.

Replacing the camera Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

To replace the camera:

Chapter 7. Replacing hardware 39

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Remove the hinge from the chassis. Refer to Removing the hinge from the chassis.

Step 6. Remove the rear cover. Refer to Removing the rear cover.

Step 7. Remove the 3 screws that secure the camera to the front bezel.

Step 8. Lift up the camera and disconnect the data cable from the camera.

Step 9. To install the new camera:

a. Connect the data cable to the new camera.

b. Line up the holes in the new camera with the mounting holes on the LED panel and secure it with the 3 screws.

Step 10. Reattach the rear cover to the LED panel.

Step 11. Reattach the hinge to the chassis, and reconnect the touch and LED panel cables to the motherboard.

Step 12. Reattach the base cover and secure it with the screws.

Replacing the LED panel Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

40 Lenovo A540/A740Hardware Maintenance Manual

Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

To replace the LED panel:

Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

Step 2. Unplug all power cords from electrical outlets.

Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Left and right view and Rear view for help with locating the various connectors.

Step 4. Remove the base cover. Refer to Removing the base cover.

Step 5. Remove the hinge from the chassis. Refer to Removing the hinge from the chassis.

Step 6. Remove the rear cover. Refer to Removing the rear cover.

Step 7. Remove the camera. Refer to Replacing the camera.

Step 8. Remove the LVDS cable and the camera-touch-backlight cables from the LED panel.

Step 9. To install the new the LED panel:

a. Connect the LVDS cable and the camera-touch-backlight cables to the connector on the new LED panel.

b. Reattach the camera to the LED panel.

Step 10. Reattach the rear cover to the LED panel.

Step 11. Reattach the hinge to the chassis, and reconnect the touch and LED panel cables to the motherboard.

Chapter 7. Replacing hardware 41

Step 12. Reattach the base cover and secure it with the screws.

A540 FRU lists This chapter lists the information on the field replaceable units (FRUs) for A540 All-In-One computers.

Attention: Be sure to read and understand all the safety information before replacing any FRUs.

Notes: FRUs that have a 1 or 2 in the CRU column are Customer Replaceable Units (CRUs).

1 identifies parts that are fairly simple to replace, requiring few or no tools.

2 identifies parts that are slightly more difficult to replace.

N-identifies parts that are not to be replaced by the customer.

FRUs FRU Description Service Part Number (FRU #)

CRU ID

C A540 NOK I3-4158 UMA W/O TV 5B20F62993 N

C A540 NOK I5-4258 UMA W/O TV 5B20F62984 N

C A540 NOK I7-4558 UMA W/O TV 5B20F62973 N

C A540 NOK I3-4158 UMA W/TV 5B20F62977 N

C A540 NOK I5-4258 UMA W/TV 5B20F62964 N

C A540 NOK I7-4558 UMA W/TV 5B20F62990 N

C A540 NOK I3-4158 DIS W/O TV 5B20F62981 N

C A540 NOK I5-4258 DIS W/O TV 5B20F62970 N

C A540 NOK I7-4558 DIS W/O TV 5B20F62997 N

C A540 NOK I3-4158 DIS W/TV 5B20F62986 N

C A540 NOK I5-4258 DIS W/TV 5B20F62975 N

C A540 NOK I7-4558 DIS W/TV 5B20F62971 N

C A540 W8S I3-4158 UMA W/O TV 5B20F62998 N

C A540 W8S I5-4258 UMA W/O TV 5B20F62987 N

C A540 W8S I7-4558 UMA W/O TV 5B20F62978 N

C A540 W8S I3-4158 UMA W/TV 5B20F62965 N

C A540 W8S I5-4258 UMA W/TV 5B20F62992 N

C A540 W8S I7-4558 UMA W/TV 5B20F62983 N

C A540 W8S I3-4158 DIS W/O TV 5B20F62972 N

C A540 W8S I5-4258 DIS W/O TV 5B20F62999 N

C A540 W8S I7-4558 DIS W/O TV 5B20F62988 N

C A540 W8S I3-4158 DIS W/TV 5B20F62979 N

C A540 W8S I5-4258 DIS W/TV 5B20F62966 N

C A540 W8S I7-4558 DIS W/TV 5B20F62967 N

C A540 W8P I3-4158 UMA W/O TV 5B20F62994 N

C A540 W8P I5-4258 UMA W/O TV 5B20F62985 N

C A540 W8P I7-4558 UMA W/O TV 5B20F62974 N

Mainboard Mainboard

42 Lenovo A540/A740Hardware Maintenance Manual

C A540 W8P I3-4158 UMA W/TV 5B20F63000 N

C A540 W8P I5-4258 UMA W/TV 5B20F62991 N

C A540 W8P I7-4558 UMA W/TV 5B20F62980 N

C A540 W8P I3-4158 DIS W/O TV 5B20F62969 N

C A540 W8P I5-4258 DIS W/O TV 5B20F62996 N

C A540 W8P I7-4558 DIS W/O TV 5B20F62976 N

C A540 W8P I3-4158 DIS W/TV 5B20F62963 N

C A540 W8P I5-4258 DIS W/TV 5B20F62989 N

C A540 W8P I7-4558 DIS W/TV 5B20F62995 N

M471B5173QH0-YK0 4GB D3L-1600S-HF 1100906 N

HMT451S6AFR8A-PB 1100638 N

MT8KTF51264HZ-1G6E1 4GB D3L-1600S-HF 1100957 N

Mic_R D9QBJ 4GB D3L-1600S-HF 1100967 N

4G

Mic_S D9QBJ 4GB D3L-1600S 1100959 N

M471B1G73QH0-YK0 8GB D3L-1600S-HF 1100907 N

HMT41GS6AFR8A-PB 1100634 N

MT16KTF1G64HZ-1G6E1 1100635 N

RAM

8G

Mic_R D9QBJ 8GB D3L-1600S-HF 1101012 N

WD5000LPVX-08V0T 6G 5.4K 500G 7mm HDD LI 16200379 N

ST500LM012 6G 9.5mm 5.4K 500G HDD 16200387 N

Seagate Yarra-1D 6G 7 5400 500 16200626 N

Hitachi HTS545050A7E380 8M 5400RPM 500G HDD 7mm

16200067 N

500G

ST500LM012 BP 9.5mm 16M 5.4K 500G HDD 16200323 N

WD10JPVX-08JC3 6G 9.5 4K 1T HDD LI 16200377 N

HTS541010A9E680 6G 9.5 4K 1TB HDD LI 16200375 N

ST1000LM024 BP 9.5mm 16M 5.4K 1T HDD 16200321 N

HDD

1TB

ST1000LM024 6G 9.5mm 5.4K 1T HDD 16200385 N

500G ST500LM000 500G SSHD 16200420 NSSHD

1TB ST1000LM014 1TB SSHD 16200421 N

ODD DB65 - Silver for DT Bundle 25014373 N

DELTA ADP-120ZB BBHT common 120W adapter 36200439 1120W

Liteon PA-1121-04LB 120w common adapter 36200440 1

FSP150-RAB common 150W adapter 36200462 1

Adapter

150W

Liteon PA-1151-11VB 150w common adapter 36200463 1

Chapter 7. Replacing hardware 43

802.11AC_BT4.0 RTL8821AU-CG 1x1ac+BT4.0 Combo USB 11202701 N

802.11AC_BT4.0 RTL8821AU-CG 1x1ac+BT4.0 Combo USB 11202701 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

WIFI_Bluetooth

802.11BGN_BT4.0

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

Philips Win8 IRWhite Controller 888900017 N

Philips IR receiver 888900019 N

Remoter Remoter

Philips Win7 IR receiver(R) 888010662 N

DVB-T Avermedia H334 DVB-T Mini TV Card 11201071 NTV tuner

ATSC Avermedia H334 ATSC Mini TV Card 11201072 N

LW BLK1.8m UL CSA Power Cord(R) 31026357 1

VL BLK1.8m UL CSA Power Cord 31026145 1

()1.8 C13 31049521 1

LW BLK1.8m ANE Power Cord 31026350 1

VL BLK1.8m ANE Power Cord 31026140 1

()1.8 C13 31049524 1

LW 1.8m JAPAN Power Cord 31039730 1

1.8C13 31049514 1

()1.8 C13 31049523 1

1.8mCCC(R) 31028776 1

LX(ASAP) 1.8M CCC C13 power cord 31040179 1

LW BLK1.8m BS Power Cord 31026096 1

VL BLK1.8m BS Power Cord(R) 31026082 1

()1.8 C13 31502861 1

LW BLK1.8m VDE Power Cord 31026355 1

VL BLK1.8m VDE Power Cord 31026144 1

()1.8 C13 31049522 1

1.8m 31033216 1

()1.8 C13 31502871 1

LW BLK1.8m BSMI Power Cord 31026349 1

VL BLK1.8m BSMI Power Cord 31026146 1

()1.8 C13 31502867 1

LW BLK1.8m SABS Power Cord 31031394 1

1.8C13 31049509 1

()1.8 C13 31502865 1

Power Cord Power Cord

44 Lenovo A540/A740Hardware Maintenance Manual

1.8m C13 IRAM 31036980 1

1.8C13 31049515 1

()1.8 C13 31502869 1

1.8m C13 Brazil 31038784 1

1.8C13 31049513 1

()1.8 C13 31502862 1

1.8m C13 Korea 31026351 1

VL BLK1.8m KTL Power Cord 31026143 1

()1.8 C13 31502870 1

Longwell 1.8M Italy C13 power cord 31039726 1

1.8C13 31049512 1

()1.8 C13 31502864 1

Longwell 1.8M Denmark C13 power cord 31039729 1

1.8C13 31049511 1

()1.8 C13 31502863 1

Longwell 1.8M SEV C13 power cord 31039732 1

1.8C13 31049516 1

()1.8 C13 31502868 1

Longwell 1.8M Israel C13 power cord 31039728 1

1.8C13 31049510 1

()1.8 C13 31502866 1

Liteon SK-8861(US) 2.4G KB-Metal8 25216020 2

Liteon SK-8861(TW) 2.4G KB-Metal8 25216021 2

Liteon SK-8861(TH) 2.4G KB-Metal8 25216022 2

Liteon SK-8861(CS-SK) 2.4G KB-Metal8 25216023 2

Liteon SK-8861(US-IN) 2.4G KB-Metal8 25216024 2

Liteon SK-8861(RU) 2.4G KB-Metal8 25216025 2

Liteon SK-8861(GB) 2.4G KB-Metal8 25216026 2

Liteon SK-8861(Nordic) 2.4G KB-Metal8 25216027 2

Liteon SK-8861(LA) 2.4G KB-Metal8 25216028 2

Liteon SK-8861(SA) 2.4G KB-Metal8 25216030 2

Liteon SK-8861(DE) 2.4G KB-Metal8 25216031 2

Liteon SK-8861(TR) 2.4G KB-Metal8 25216032 2

Liteon SK-8861(ES) 2.4G KB-Metal8 25216033 2

Liteon SK-8861(IT) 2.4G KB-Metal8 25216034 2

Liteon SK-8861(FR) 2.4G KB-Metal8 25216035 2

Liteon SK-8861(KR) 2.4G KB-Metal8 25216036 2

Liteon SK-8861(JP) 2.4G KB-Metal8 25216037 2

Liteon SK-8861(EN-FR) 2.4G KB-Metal8 25216038 2

KB&Mouse KB&Mouse

Chapter 7. Replacing hardware 45

Liteon SK-8861(BE-EN) 2.4G KB-Metal8 25216039 2

Liteon SK-8861(US-EU) 2.4G KB-Metal8 25216040 2

Liteon SK-8861(CH) 2.4G KB-Metal8 SD50F65816 2

Liteon ZTM600 2.4G Mouse (WW) Silver 25216043 2

Liteon SM-8861 Mouse(WW) improved silver 25216250 2

LTO SM-8861 MC(No BTY) improved silver 25216336 2

DISPLAY DISPLAY Module,C,A540,23.8,TS,FHD LG 5D10F62982 N

COVER COVER Rear,C,A540,W/LOGO 5CB0F63308 N

N/A N/A A540 Speaker 90205401 N

HINGE HINGE C,A540 5H50F63290 N

COVER COVER Upper,C,A540,W/TV 5CB0F63293 N

COVER COVER Upper,C,A540,W/O TV 5CB0F63300 N

COVER COVER Upper,C,A540,W/O TV W/O HDMI_IN 5CB0F63311 N

COVER COVER Lower,C,A540 5CB0F63305 N

FOOT FOOT Rubber,C,A540 5F40F63301 N

BRACKET BRACKET HDD,C,A540,L+R 5B40F63303 N

CABLE CABLE HDD SATA,C,A540 5C10F63009 N

FOOT FOOT Panel,C,A540 5F40F63299 N

BRACKET BRACKET DC-IN,C,A540 5B40F63297 N

CABLE CABLE DC-IN,C,A540 5C10F63295 N

N/A N/A A540 Taisol Thermal DIS W/Gasket*2 90205300 N

N/A N/A A540 Coolermaster Thermal DIS W/Gasket*2 90205301 N

N/A N/A A540 Taisol Thermal UMA W/Gasket*2 90205302 N

N/A N/A A540 Coolermaster Thermal UMA W/Gasket*2 90205303 N

N/A N/A A540 Delta Fan 90205304 N

N/A N/A A540 Sunon Fan 90205305 N

BRACKET BRACKET LCD,C,A540 5B40F63291 N

MECHANICAL MECHANICAL Power Board Bracket ,C,A540 5M20F63298 N

CABLE CABLE LVDS,C,A540 LG 5C10F63307 N

CABLE CABLE TV Scalar BD,C,A540,3IN1 5C10F63294 N

CABLE CABLE Power BD,C,A540 5C10F63292 N

CARDPOP CARDPOP Power BD,C,A540,W/O cable 5C50F63304 N

CABLE CABLE NFC,C,A540 5C10F63310 N

CARDPOP CARDPOP TV Scalar BD,C,A540,W/O cable 5C50F63296 N

ANTENNA ANTENNA WLAN,C,A540,Main+AUX 5A30F63288 N

CONNECTOR CONNECTOR TV JACK,C,A540,F 5CA0F63309 N

CONNECTOR CONNECTOR TV JACK,C,A540,P 5CA0F63289 N

A740 FRU lists This chapter lists the information on the field replaceable units (FRUs) for A540 All-In-One computers.

46 Lenovo A540/A740Hardware Maintenance Manual

Attention: Be sure to read and understand all the safety information before replacing any FRUs.

Notes: FRUs that have a 1 or 2 in the CRU column are Customer Replaceable Units (CRUs).

1 identifies parts that are fairly simple to replace, requiring few or no tools.

2 identifies parts that are slightly more difficult to replace.

N-identifies parts that are not to be replaced by the customer.

FRUs FRU Description Service Part Number (FRU #)

CRU ID

BDPLANAR C,A540,NOK,I3-4158, DIS,W/O TV 5B20F62981 N

BDPLANAR C,A540,NOK,I5-4258, DIS,W/O TV 5B20F62970 N

BDPLANAR C,A540,NOK,I7-4558, DIS,W/O TV 5B20F62997 N

BDPLANAR C,A540,NOK,I3-4158, DIS,W/TV 5B20F62986 N

BDPLANAR C,A540,NOK,I5-4258, DIS,W/TV 5B20F62975 N

BDPLANAR C,A540,NOK,I7-4558, DIS,W/TV 5B20F62971 N

BDPLANAR C,A540,W8S,I3-4158, DIS,W/O TV 5B20F62972 N

BDPLANAR C,A540,W8S,I5-4258, DIS,W/O TV 5B20F62999 N

BDPLANAR C,A540,W8S,I7-4558, DIS,W/O TV 5B20F62988 N

BDPLANAR C,A540,W8S,I3-4158, DIS,W/TV 5B20F62979 N

BDPLANAR C,A540,W8S,I5-4258, DIS,W/TV 5B20F62966 N

BDPLANAR C,A540,W8S,I7-4558, DIS,W/TV 5B20F62967 N

BDPLANAR C,A540,W8P,I3-4158, DIS,W/O TV 5B20F62969 N

BDPLANAR C,A540,W8P,I5-4258, DIS,W/O TV 5B20F62996 N

BDPLANAR C,A540,W8P,I7-4558, DIS,W/O TV 5B20F62976 N

BDPLANAR C,A540,W8P,I3-4158, DIS,W/TV 5B20F62963 N

BDPLANAR C,A540,W8P,I5-4258, DIS,W/TV 5B20F62989 N

BDPLANAR C,A540,W8P,I7-4558, DIS,W/TV 5B20F62995 N

BDPLANAR C A740 NOK I3-4158 DIS Q W/O TV 5B20F65651 N

BDPLANAR C A740 NOK I5-4258 DIS Q W/O TV 5B20F65677 N

BDPLANAR C A740 NOK I7-4558 DIS Q W/O TV 5B20F65669 N

BDPLANAR C A740 NOK I3-4158 DIS Q W/TV 5B20F65662 N

BDPLANAR C A740 NOK I5-4258 DIS Q W/TV 5B20F65656 N

BDPLANAR C A740 NOK I7-4558 DIS Q W/TV 5B20F65648 N

BDPLANAR C A740 W8S I3-4158 DIS Q W/O TV 5B20F65672 N

BDPLANAR C A740 W8S I5-4258 DIS Q W/O TV 5B20F65666 N

BDPLANAR C A740 W8S I7-4558 DIS Q W/O TV 5B20F65664 N

BDPLANAR C A740 W8S I3-4158 DIS Q W/TV 5B20F65658 N

BDPLANAR C A740 W8S I5-4258 DIS Q W/TV 5B20F65650 N

BDPLANAR C A740 W8S I7-4558 DIS Q W/TV 5B20F65676 N

BDPLANAR C A740 W8P I3-4158 DIS Q W/O TV 5B20F65657 N

BDPLANAR C A740 W8P I5-4258 DIS Q W/O TV 5B20F65649 N

Mainboard

Chapter 7. Replacing hardware 47

BDPLANAR C A740 W8P I7-4558 DIS Q W/O TV 5B20F65674 N

BDPLANAR C A740 W8P I3-4158 DIS Q W/TV 5B20F65667 N

BDPLANAR C A740 W8P I5-4258 DIS Q W/TV 5B20F65660 N

BDPLANAR C A740 W8P I7-4558 DIS Q W/TV 5B20F65655 N

M471B5173QH0-YK0 4GB D3L-1600S-HF

1100906 N

HMT451S6AFR8A-PB 1100638 N

MT8KTF51264HZ-1G6E1 4GB D3L-1600S -HF

1100957 N

Mic_R D9QBJ 4GB D3L-1600S-HF 1100967 N

4G

Mic_S D9QBJ 4GB D3L-1600S 1100959 N

M471B1G73QH0-YK0 8GB D3L-1600S-HF 1100907 N

HMT41GS6AFR8A-PB 1100634 N

MT16KTF1G64HZ-1G6E1 1100635 N

RAM

8G

Mic_R D9QBJ 8GB D3L-1600S-HF 1101012 N

WD5000LPVX-08V0T 6G 5.4K 500G 7mm HDD LI

16200379 N

ST500LM012 6G 9.5mm 5.4K 500G HDD 16200387 N

Seagate Yarra-1D 6G 7 5400 500 16200626 N

Hitachi HTS545050A7E380 8M 5400RPM 500G HDD 7mm

16200067 N

500G

ST500LM012 BP 9.5mm 16M 5.4K 500G HDD 16200323 N

WD10JPVX-08JC3 6G 9.5 4K 1T HDD LI 16200377 N

HTS541010A9E680 6G 9.5 4K 1TB HDD LI 16200375 N

ST1000LM024 BP 9.5mm 16M 5.4K 1T HDD 16200321 N

HDD

1TB

ST1000LM024 6G 9.5mm 5.4K 1T HDD 16200385 N

500G ST500LM000 500G SSHD 16200420 NSSHD

1TB ST1000LM014 1TB SSHD 16200421 N

ODD DB65 - Silver for DT Bundle 25014373 N

FSP150-RAB common 150W adapter 36200462 1Adapter Adapter

Liteon PA-1151-11VB 150w common adapter 36200463 1

802.11AC_BT4.0 RTL8821AU-CG 1x1ac+BT4.0 Combo USB 11202701 N

802.11AC_BT4.0 RTL8821AU-CG 1x1ac+BT4.0 Combo USB 11202701 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

WIFI_Bluetooth

802.11BGN_BT4.0

RTL8723AS-VAU 1x1bgn BT4.0 Combo USB 20200052 N

48 Lenovo A540/A740Hardware Maintenance Manual

Philips Win8 IRWhite Controller 888900017 N

Philips IR receiver 888900019 N

Remoter Remoter

Philips Win7 IR receiver(R) 888010662 N

DVB-T Avermedia H334 DVB-T Mini TV Card 11201071 NTV tuner

ATSC Avermedia H334 ATSC Mini TV Card 11201072 1

LW BLK1.8m UL CSA Power Cord(R) 31026357 1

VL BLK1.8m UL CSA Power Cord 31026145 1

()1.8 C13 31049521 1

LW BLK1.8m ANE Power Cord 31026350 1

VL BLK1.8m ANE Power Cord 31026140 1

()1.8 C13 31049524 1

LW 1.8m JAPAN Power Cord 31039730 1

1.8C13 31049514 1

()1.8 C13 31049523 1

1.8mCCC(R) 31028776 1

LX(ASAP) 1.8M CCC C13 power cord 31040179 1

LW BLK1.8m BS Power Cord 31026096 1

VL BLK1.8m BS Power Cord(R) 31026082 1

()1.8 C13 31502861 1

LW BLK1.8m VDE Power Cord 31026355 1

VL BLK1.8m VDE Power Cord 31026144 1

()1.8 C13 31049522 1

1.8m 31033216 1

()1.8 C13 31502871 1

LW BLK1.8m BSMI Power Cord 31026349 1

VL BLK1.8m BSMI Power Cord 31026146 1

()1.8 C13 31502867 1

LW BLK1.8m SABS Power Cord 31031394 1

1.8C13 31049509 1

()1.8 C13 31502865 1

1.8m C13 IRAM 31036980 1

1.8C13 31049515 1

()1.8 C13 31502869 1

1.8m C13 Brazil 31038784 1

1.8C13 31049513 1

()1.8 C13 31502862 1

1.8m C13 Korea 31026351 1

VL BLK1.8m KTL Power Cord 31026143 1

Power Cord Power Cord

Chapter 7. Replacing hardware 49

()1.8 C13 31502870 1

Longwell 1.8M Italy C13 power cord 31039726 1

1.8C13 31049512 1

()1.8 C13 31502864 1

Longwell 1.8M Denmark C13 power cord 31039729 1

1.8C13 31049511 1

()1.8 C13 31502863 1

Longwell 1.8M SEV C13 power cord 31039732 1

1.8C13 31049516 1

()1.8 C13 31502868 1

Longwell 1.8M Israel C13 power cord 31039728 1

1.8C13 31049510 1

()1.8 C13 31502866 1

Liteon SK-8861(US) 2.4G KB-Metal8 25216020 2

Liteon SK-8861(TW) 2.4G KB-Metal8 25216021 2

Liteon SK-8861(TH) 2.4G KB-Metal8 25216022 2

Liteon SK-8861(CS-SK) 2.4G KB-Metal8 25216023 2

Liteon SK-8861(US-IN) 2.4G KB-Metal8 25216024 2

Liteon SK-8861(RU) 2.4G KB-Metal8 25216025 2

Liteon SK-8861(GB) 2.4G KB-Metal8 25216026 2

Liteon SK-8861(Nordic) 2.4G KB-Metal8 25216027 2

Liteon SK-8861(LA) 2.4G KB-Metal8 25216028 2

Liteon SK-8861(SA) 2.4G KB-Metal8 25216030 2

Liteon SK-8861(DE) 2.4G KB-Metal8 25216031 2

Liteon SK-8861(TR) 2.4G KB-Metal8 25216032 2

Liteon SK-8861(ES) 2.4G KB-Metal8 25216033 2

Liteon SK-8861(IT) 2.4G KB-Metal8 25216034 2

Liteon SK-8861(FR) 2.4G KB-Metal8 25216035 2

Liteon SK-8861(KR) 2.4G KB-Metal8 25216036 2

Liteon SK-8861(JP) 2.4G KB-Metal8 25216037 2

Liteon SK-8861(EN-FR) 2.4G KB-Metal8 25216038 2

Liteon SK-8861(BE-EN) 2.4G KB-Metal8 25216039 2

Liteon SK-8861(US-EU) 2.4G KB-Metal8 25216040 2

Liteon SK-8861(CH) 2.4G KB-Metal8 SD50F65816 2

Liteon ZTM600 2.4G Mouse (WW) Silver 25216043 2

Liteon SM-8861 Mouse(WW) improved silver 25216250 2

KB&Mouse KB&Mouse

LTO SM-8861 MC(No BTY) improved silver 25216336 2

DISPLAY Module C A740 27 TS FHD AUO 5D10F65678 N

DISPLAY Module C A740 27 TS QHD SAM 5D10F65670 N

50 Lenovo A540/A740Hardware Maintenance Manual

COVER Rear C A740 W/LOGO 5CB0F65661 N

Speaker A540 Speaker 90205401 N

HINGE C A740 5H50F65671 N

COVER Upper,C,A540,W/TV 5CB0F63293 N

COVER Upper,C,A540,W/O TV 5CB0F63300 N

COVER Upper,C,A540,W/O TV W/O HDMI_IN 5CB0F63311 N

COVER Lower,C,A540 5CB0F63305 N

FOOT Rubber,C,A540 5F40F63301 N

BRACKET HDD,C,A540,L+R 5B40F63303 N

CABLE HDD SATA,C,A540 5C10F63009 N

FOOT Panel,C,A540 5F40F63299 N

BRACKET DC-IN,C,A540 5B40F63297 N

CABLE DC-IN,C,A540 5C10F63295 N

A540 Taisol Thermal DIS W/Gasket*2 90205300 N

A540 Coolermaster Thermal DIS W/Gasket*2 90205301 N

A540 Taisol Thermal UMA W/Gasket*2 90205302 N

A540 Coolermaster Thermal UMA W/Gasket*2 90205303 N

A740 Taisol Thermal DIS W/Gasket*3 90205306 N

Thermal Thermal

A740 Coolermaster Thermal DIS W/Gasket*3 90205307 N

A540 Delta Fan 90205304 NFan Fan

A540 Sunon Fan 90205305 N

MECHANICAL MECHANICAL Power Board Bracket ,C,A540 5M20F63298 N

CABLE CABLE LVDS C A740 AUO 5C10F65663 N

CABLE CABLE LVDS C A740 SAM 5C10F65653 N

CABLE CABLE TV Scalar BD C A740 3IN1 AUO 5C10F65675 N

CABLE CABLE TV Scalar BD C A740 3IN1 SAM 5C10F65665 N

CABLE CABLE Power BD C A740 5C10F65654 N

CARDPOP CARDPOP Power BD,C,A540,W/O cable 5C50F63304 N

CABLE CABLE NFC C A740 5C10F65668 N

CARDPOP CARDPOP TV Scalar BD C A740 FHD 5C50F65659 N

CARDPOP CARDPOP TV Scalar BD C A740 QHD 5C50F65652 N

ANTENNA ANTENNA WLAN C A740 Main+AUX 5A30F65673 N

CONNECTOR CONNECTOR TV JACK,C,A540,F 5CA0F63309 N

CONNECTOR CONNECTOR TV JACK,C,A540,P 5CA0F63289 N

Chapter 7. Replacing hardware 51

52 Lenovo A540/A740Hardware Maintenance Manual

Chapter 8. General information

This chapter provides general information that applies to all computer models covered by this manual.

Additional Service Information This chapter provides additional information that the service representative might find helpful.

Power management

Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors.

Advanced configuration and power interface (ACPI) BIOS

As this computer has an ACPI BIOS system, the operating system is allowed to control the power management features of the computer and the settings for Advanced Power Management (APM) BIOS mode is ignored. Not all operating systems support ACPI BIOS mode.

Automa

Manualsnet FAQs

If you want to find out how the AIO A740 Lenovo works, you can view and download the Lenovo AIO A740 Computer Hardware Maintenance Manual on the Manualsnet website.

Yes, we have the Hardware Maintenance Manual for Lenovo AIO A740 as well as other Lenovo manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Hardware Maintenance Manual should include all the details that are needed to use a Lenovo AIO A740. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Lenovo AIO A740 Computer Hardware Maintenance Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Lenovo AIO A740 Computer Hardware Maintenance Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Lenovo AIO A740 Computer Hardware Maintenance Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Lenovo AIO A740 Computer Hardware Maintenance Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Lenovo AIO A740 Computer Hardware Maintenance Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.