Contents

KORG KHP-5000 HT-70 Owner's Manual PDF

1 of 76
1 of 76

Summary of Content for KORG KHP-5000 HT-70 Owner's Manual PDF

E F G 2

2

Precautions Location Using the unit in the following locations can result in a malfunction.

In direct sunlight Locations of extreme temperature or humidity Excessively dusty or dirty locations Locations of excessive vibration Close to magnetic elds

Power supply Please connect the designated AC adapter to an AC outlet of the correct voltage. Do not connect it to an AC outlet of voltage other than that for which your unit is intended.

Interference with other electrical devices Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions.

Handling To avoid breakage, do not apply excessive force to the switches or controls.

Care If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid cleaners such as benzene or thinner, or cleaning compounds or ammable pol- ishes.

Keep this manual After reading this manual, please keep it for later ref- erence.

Keeping foreign matter out of your equipment Never set any container with liquid in it near this equipment. If liquid gets into the equipment, it could cause a breakdown, re, or electrical shock. Be careful not to let metal objects get into the equip- ment. If something does slip into the equipment, unplug the AC adapter from the wall outlet. Then con- tact your dealer or qualied installation technician for assistance.

THE FCC REGULATION WARNING (for USA) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi- cations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for

help. Unauthorized changes or modication to this system can void the users authority to operate this equipment.

Notice regarding disposal (EU only) When this crossed-out wheeled bin symbol is dis- played on the product, owners manual, battery, or battery package, it signies that when you wish to dis- pose of this product, manual, package or battery you must do so in an approved manner. Do not discard this product, manual, package or battery along with ordi- nary household waste. Disposing in the correct man- ner will prevent harm to human health and potential

damage to the environment. Since the correct method of disposal will depend on the applicable laws and regulations in your local- ity, please contact your local administrative body for details. If the battery contains heavy metals in excess of the regulated amount, a chemical symbol is displayed below the crossed-out wheeled bin symbol on the battery or battery package.

IMPORTANT NOTICE TO CONSUMERS This product has been manufactured according to strict speci- cations and voltage requirements that are applicable in the coun- try in which it is intended that this product should be used. If you have purchased this product via the internet, through mail order, and/or via a telephone sale, you must verify that this product is intended to be used in the country in which you reside. WARNING: Use of this product in any country other than that for which it is intended could be dangerous and could invalidate the manufacturers or distributors warranty. Please also retain your receipt as proof of purchase otherwise your product may be disqualied from the manufacturers or distributors warranty.

* All product names and company names are the trademarks or registered trademarks of their respective owners.

3

Table of Contents

Introduction ................................................ 4 Main features .........................................................4

Parts and their function............................. 5 Operating panel .....................................................5

Rear panel .............................................................6

Getting ready to play and demo song...... 7 Getting ready to play..............................................7

Connecting the power............................................... 7 Silencing the acoustic piano sound .......................... 7 Headphones ............................................................. 7 If You Have Trouble Seeing the Control Panel ......... 8 Turning the power on................................................ 8 Adjusting the volume ................................................ 8

Listening to the Sound Demos...............................8 Listening to the sound demos................................... 8

Playing the HT-70..................................... 10 Selecting a sound ................................................10

Using the pedals ..................................................10

Adding reverberation to the sound (Reverb)........11

Playing along with the metronome.......................12 To sound the metronome........................................ 12 Changing the Metronome Settings ......................... 12

Additional Features ..............................................14

Recording and playing back your performance ......... 15 Recording your performance ...............................15

Quick Recording (Recording a New Song) ......... 15 Recording a Performance ................................... 15 Saving a Recorded Song .................................... 16 Deleting a Song................................................... 16 Deleting a Part .................................................... 16 To See How Much

More Data Can Be Recorded............................ 16

Playing Songs ......................................................17 Selecting a Song ................................................. 17 Pausing Song Play.............................................. 17 Restarting a Playing Song................................... 17 Changing the Tempo of a Playing Song ............. 17 Moving to a Different Position (Measure)............ 17 To Repeat Play of a

Specified Song Segment (AB Repeat) ........... 17

Additional Features ................................. 18 Adjusting the Pitch ...............................................18

Choosing a temperament.....................................18

Adjusting the brightness of the sound (Brilliance)...........18

Changing the sensitivity of the keyboard ............ 19

Changing the key (Transpose)............................ 19 To play the song a semitone higher.....................19 The song is in the key of Bb but you want

to play it using the fingering of the key of G.......19

Restoring the factory settings.............................. 19

MIDI ........................................................... 20 What is MIDI?...................................................... 20

Making MIDI connections.................................... 20

MIDI channels ..................................................... 20

Using the HT-70 as a multi-timbral sound module .................... 20

Local on/off setting .............................................. 20

Program changes................................................ 21

USB ........................................................... 22 Using MIDI through a USB Connection............... 22

USB Mode........................................................... 23

Appendix................................................... 24 Troubleshooting .................................................. 24

Using the HT-70 without silencing the acoustic piano............... 25

Error Messages................................................... 25

Specifications ...................................................... 25

Feature List ......................................................... 74 Metronome Functions............................................. 74 General Functions #1 ............................................. 74 General Functions #2 ............................................. 74 General Functions #3 ............................................. 74

MIDI implementation chart .................................. 75

Conventions in this owner's manual

Switches

Switches on the HT-70 are enclosed in square brackets [ ]

(p.) : Indicates a reference page.

: Indicates a function for the model with speak- ers.

: Indicates a caution when using the HT-70.

: Indicates a hint when using the HT-70.

4

Introduction

Main features Diverse array of sounds (p.10)

Choose from eight high-quality sounds available only from Korg, including a concert grand piano. Stereo sampling is used, letting you enjoy a pleasant spaciousness in addition to the rich expressive- ness of a concert grand piano.

Ten sound demos (p.8) Ten built-in demo songs showcase the distinctive qualities of each sound.

Effect functions (p.11, p.18) Reverb and brilliance effects are included. You can set the reverb to any of three levels (depths) for each voice. Use the brilliance settings to adjust the brightness of the sound.

Pedal effects (p.10) The piano pedals can be used to affect the HT-70s internal sounds, with similar functionality.

Metronome function (p.12) The built-in metronome is widely adjustableyou can freely set the time signature, the tempo, the volume, and the sound, and you can add a bell tone or digital tone for the accents.

Touch Control function (p.19) Keyboard dynamic response is one of the most important aspects of a piano, and the HT-70 lets you choose from three different types of dynamic response.

Adjustable pitch (p.18, p.19) The built-in pitch controller lets you make ne adjustments to the pitch. The transpose feature lets you change the performance key to match the key of another instrument or of a specic musical piece.

Temperament (p.18) In addition to the standard equal temperament, you can choose from two classical temperaments (Werckmeister and Kirnberger) for historically accurate performances.

Recorder function (p.15) The HT-70s built-in recorder lets you record and play back your own performances.

Connectors (p.6, p.20, p.22) LINE OUT, MIDI, and USB connectors are provided, letting you connect the HT-70 to audio equip- ment, other MIDI equipment, or a computer.

Parts and their function

Operating panel

1. Headphone jacks You can connect stereo headphones (phone plug) to these jacks. Two stereo headphones can be con- nected simultaneously.

If youre using the model with speakers and have connected the included speakers, the included speakers will not sound if youve connected head- phones.

2. [POWER] switch This switch toggles power between two states, ON (multidisplay illuminated) and OFF (standby).

The instrument continues to receive trace power while in standby state. If you wish to shut the power completely off, unplug the AC adapters power cord from the wall outlet.

3. [VOLUME] knob This controls the volume of the signal that is sent from the headphones and line out jacks (p.8).

On models with speakers, this also controls the vol- ume of the speakers.

4. Sound selector Use this to select sounds (p.10). You can choose from eight sounds: PIANO 1, 2, E.PIANO (electric piano) 1, 2, HARPSI. (harpsi- chord), P.ORGAN (pipe organ), E.ORGAN (electric organ), and STRINGS (strings).

5. [SONG] switch and LED Use this switch to select a song to be played or recorded. Press this switch together with the [REVERB] switch to play one of the built-in sound demos (p.8).

6. [DISPLAY] switch and LEDs Changes the content of the multidisplay. The illumi- nated LED indicates the current content.

When the instrument is set to Function mode, you use this switch to change the value of a set- ting(p.74)

7. TEMPO LED Flashes in time with the song during playback and recording.

8. Recorder section Use these buttons to start, pause, resume, and stop playback or recording (p.15). When the [ ] switch is ashing, you use these but- tons to set the metronomes features: the bell accent, the tempo, and the metronome sound.

9. [REVERB] switch and LED Sets the reverb effect (p.11). Also used together with the [SONG] switch to play any of the built-in sound demos (p.8 ).

10.[FUNC.] switch and LED Sets the instrument into Function mode, so that you can carry out various non-performance settings and actions (save or delete a song, select temperament, make MIDI settings, etc.) (p.74).

11.Multidisplay Displays one of several types of information, as identied by the illuminated [DISPLAY] LED. May show metronome tempo, recorder tempo, recorded song number, measure within the song, etc.

43 11

5 6 7 8

9 12 13 1410

2

1

Examples During song play

Tempo

Song No.

Measure (location in song)

Dot On / Flashing / Off On / On (out of range) / Off

During AB repeat

During memory writing (Cycling display)

5

6

12.[] and [] switches Use these to adjust the metronome and recorder tempos, and to select values for various settings.

13.[ ] switch Turns the metronome ON or OFF. Hold the switch down if you wish to change the metronome settings (p.12).

14.[PART 1] and [PART 2] switches Selects the part for recording or playback (p.15). When the [ ] switch is ashing, you use these but- tons to set the volume, time signature, and other settings.

Rear panel

1. MIDI connectors You can connect these connectors to MIDI devices such as synthesizers, sequencers, or rhythm machines in order to send and receive data (p.20). IN This connector receives MIDI messages. Connect this to the MIDI OUT connector of the external MIDI device that will be controlling the HT-70. OUT This connector transmits MIDI messages. Connect this to the MIDI IN connector of the external MIDI device that the HT-70 will be controlling.

2. USB port You can use a USB cable from this port to connect the HT-70 directly to your computer in order to transfer data (p.22).

3. LINE OUT jack You can connect this jack to the input jack of your amplied speaker system and listen to the HT-70 through your system, or connect it to your record- ing device and record the sound of the HT-70. Use a stereo mini-plug cable.

You must make all connections with the power turned off. Careless operation may damage the HT- 70 or the device to which its connected, or may cause malfunctions.

Connection cables are sold separately. You will need to obtain the appropriate commercially-available cables for your equipment.

4. DC12V jack Connect the included AC adapter here (p.7).

5. Speaker connector: Connects to the dedicated speakers.

2 43

5

1

7

Getting ready to play and demo song

Getting ready to play

Connecting the power

1. Be sure that the HT-70 power is off.

2. Connect the included power cord to the included AC adapter, and plug the adapters DC plug into the DC12V connector on the HT-70.

Use the supplied AC adapter only. Use of another AC adapter may result in damage to the unit.

Silencing the acoustic piano sound Use the muting unit to set or release the mute for the acoustic piano. Your muting unit may be either electric (Fig. 2.1) or manual (Fig. 2.2). If the muting unit on your instrument does not match either of these gures, please consult your dealer or a qualied service agent for usage instructions.

All the functions of the HT-70 are available regardless of whether the acoustic piano is silenced. The section Using the HT-70 without silencing the acoustic piano on page 25 describes some ways to use the HT-70 together with the acoustic piano sound.

Even if the piano is silenced, there may be some leakage of the acoustic piano sound if you play a chord strongly.

If you have an electric muting unit... To silence the piano, press in the switch on the muting unit located at the base of the piano (Fig. 2.1), so that the switch is in the STOP posi- tion. The MUTING BAR LED will light up to indicate that muting is ON. To return to acoustic piano sound, press the switch again, so that it pops out to the FREE position and the LED goes off.

Dont operate while youre playing.

If you have a manual muting unit... As shown in Fig. 2.2, pull the lever of the mute unit located on the bottom panel of the piano toward yourself, and lower the lever to lock it into place. To go back to playing the acoustic piano conventionally, return the lever to its original position.

Don't operate this lever while you're playing

Headphones Headphone jacks are located on the front of the sound units ( p.5). These jacks accept standard stereo headphone plugs.

Since there are two headphone jacks, two people can enjoy the sound of the piano.

On the model with speakers, plugging in headphones will mute the included speakers. Use head- phones if the sound might be an annoyance to those nearby, such as when practicing at night.

Fig.1

AC adapter to an AC outlet Power cable for AC adapter

Bottom panel of piano (HT-70 rear panel)

DC plug

Fig. 2.1

Fig. 2.2

8

If your headphones use a mini phone adapter plug, grasp the adapter plug when connect- ing or disconnecting your headphones.

When using headphones, you should protect your ears by avoiding extended listening at high volume.

If You Have Trouble Seeing the Control Panel You can adjust the angle to improve the view. Simply loosen the bolt and screw on each side (left and right), adjust the angle as desired, and then retighten.

Be sure to retighten securely after making the adjustment.

Turning the power on Press [POWER] to turn the power on. The multidisplay comes on when the power is turned on. To turn the power off, press [POWER] again, so that the multidisplay goes dark.

When you turn the power off, all settings other than those stored in nonvolatile memory return to their factory defaults. Recorded performance data remains in memory and is not lost.

Adjusting the volume Turn the [VOLUME] knob to adjust the volume. (See gure 4.)

This controls the volume that is output from the headphone jacks. Turn the knob toward the left to decrease the volume, or toward the right to increase the volume.

On the model with speakers, this also controls the volume that is output from the speakers. For some sounds, the sound from the speakers may be distorted if you set the volume to the maxi- mum position.

Listening to the Sound Demos The HT-70 includes ten demo songs designed to highlight the features of its eight differ- ent sounds.

Listening to the sound demos List of sound demos

No. Sound Song title Composer

1 PIANO1 La Campanella F.Liszt

2 PIANO1 The Path Of Truth Jordan Rudess

3 PIANO1 Rhapsody in Blue G.Gershwin

4 PIANO2 Someone To Watch Over Me G.Gershwin

5 E.PIANO1 Ramble M.Sakaguchi

6 E.PIANO2 KORG Original KORG

7 HARPSI. Invention No.8 J.S.Bach

8 P.ORGAN Toccata in D moll J.S.Bach

9 E.ORGAN KORG Original KORG

10 STRINGS First Snow M.Sakaguchi

Fig.3

Bolt

Underside of Piano

Screw

Fig.4

Softer Louder

1. Simultaneously press the [SONG] switch and [REVERB] switch. The [SONG] switchs LED begins ashing.

2. Use the sound selector to choose the song you want to hear from the above list; the selected demo song will begin playing. If you dont select a song within three seconds, the songs will begin playing consecu- tively, starting with sound demo number 1. When sound demo number 10 has nished playing, playback will return to sound demo number 1 and will continue.

To select demo 2 or demo 3, turn the selector to Piano 1 and then press [] or [] as neces- sary.

3. When the sound demo you selected has nished playing, playback will continue in suc- cession to the next song.

4. During demo play, you can use the [ ] switch to pause and resume playback. (The switch lamp comes on solid during play, and ashes during pause.) Pressing the [] switch will stop playback and reset the position to the beginning of the demo.

5. To stop playback, press the [SONG] switch. The [SONG] switch will go dark, playback will stop.

If you want to switch to a different sound demo, use the sound selector to switch the demo song. For example if sound demo number 1 is playing, but you want to switch to number 10, simply turn the sound selector to STRINGS. The sound demo playback will switch to number 10 and continue playing. Alternatively, you can press the [][] switches to select a song. In this case, the position of the sound selector is ignored.

Demo play starts automatically ([ ] lights up) when you change the selection.

While a sound demo is playing, you can play the keyboard to play the same sound, but you cant switch to a different sound.

You cant change the reverb setting while a sound demo is playing.

You cant change the tempo of a sound demo.

12

1, 4 2

2

9

1

Playing the HT-70

Selecting a sound

Turn the sound selector to select a sound.

Using the pedals Damper pedal, Sostenuto pedal and Soft pedal can be applied to the HT-70s sounds. You can use the pedals of the acoustic piano to make your performance more expres- sive.

Damper pedal The notes will be sustained while you hold down the pedal, creating a rich resonance. The depth to which you press the pedal will control the amount of damper that is applied (half-pedal effect).

Sostenuto pedal Use this pedal to sustain specic notes only. Stepping on the pedal sustains all the notes that you are currently pressing on the keyboard; additional notes that you play while the pedal is already down are not sustained.

Soft pedal The sound will be softer and milder while you hold down the pedal. The depth to which you press the pedal will control the amount of soft-pedal that is applied (half- pedal effect).

Sound Description

PIANO1 A top-quality grand piano sound with superb presence

PIANO2 A concert grand sound, with rich bass notes

E.PIANO1 A light and clear electric piano sound

E.PIANO2 A crisp electric piano sound with a nice attack

HARPSI. A classical and realistic harpsichord sound

P.ORGAN A solemn pipe organ sound

E.ORGAN A funky jazz organ sound

STRINGS An ensemble sound with violin and other bowed strings

0

Adding reverberation to the sound (Reverb) You can add reverberation (reverb) to the sound to create the spacious ambience typical of a performance in a concert hall.

Reverb will be alternately turned on or off each time you press the [REVERB] switch. When you change the setting, the HT-70 will write the new setting to memory. During this time, the multidisplay will indicate that writing is in progress (p.5).

Do not turn the HT-70 power off while writing is in progress. Doing so may cause loss or corruption of memorized settings and song data.

Setting the Reverb Depth

1. Hold down [REVERB] for about one second. The switchs LED begins ashing.

2. Press [] or [] to select the desired depth. The multidisplay shows the current setting. The display shows 01 (shallow), 02 (standard), or 03 (deep).

3. When you have made the setting, press [REVERB] again to return to the original display. When you change the setting, the HT-70 will write the new setting to memory. During this time, the multidisplay will indicate that writing is in progress (p.5 ). Once writ- ing is completed, the [REVERB] LED will either light up or go dark to indicate whether reverb is currently on or off for the sound selected by the sound selector.

Do not turn the HT-70 power off while writing is in progress. Doing so may cause loss or corruption of memorized settings and song data.

If you switch to a different sound or turn the power off before writing the new depth setting into memory, the reverb depth will return to its original setting.

You can specify the reverb on/off and depth settings independently for each sound. With the factory settings, they are set to the settings typical for each sound.

Since the Piano 1 sound simulate the string resonance of an acoustic piano, a small amount of reverb will remain even if you turn reverb off.

11

1

Playing along with the metronome Its convenient to use the metronome when you want to play to an accurate tempo.

To sound the metronome

1. Press the [ ] switch. The [ ] switch will light.

2. To stop the metronome, press the [ ] switch once again. The [ ] switch will go dark.

Changing the Metronome Settings Settings described here (with the exception of tempo and time signature) are retained even while the power is off. When you press [ ] after making each change, the HT-70 automatically writes the new value into nonvolatile memory. During this time, the multidisplay will indicate that writing is in progress (p.5 ).

Do not turn the HT-70 power off while writing is in progress. Doing so may cause loss or cor- ruption of memorized settings and song data.

Changing the Tempo Setting

1. Hold down [ ] for at least one second. The switch begins ashing.

2. The TEMPO indicator LED (next to the [DISPLAY] switch) comes on, and the multidis- play shows the current tempo setting. If the TEMPO indicator LED does not come on, press [TEMPO ()].

3. Use [] or [] to set the desired tempo. Press briey to change the value by 1, or hold the switch down to change continuously. If you wish to reset the tempo to its factory default, press [] and [] at the same time. The available range is ( =) 4 to 250.

4. When you have made set the value, press [ ] again. The HT-70 returns to its previous state. The [ ] switch stops ashing (either goes off or else comes on solid).

1, 2

1, 4

2

3

3

2

Changing the Loudness

1. Hold down [ ] for at least one second. The switch begins ashing.

2. Press the [VOL. (PART 2)] switch. The switch lights up, and the multidisplay shows the current volume setting.

3. Use [] or [] to set the desired level. Press briey to change the value by 1, or hold the switch down to change continuously. The available range is 0 to 127.

4. When you have set the value, press [ ] again. The HT-70 returns to its previous state. The [ ] switch stops ashing (either goes off or else comes on solid).

Changing the time signature

1. Hold down [ ] for at least one second. The switch begins ashing.

2. Press the [BEAT (PART 1)] switch. The switch lights up, and the multidisplay shows the current time signature.

3. Use [] or [] to set the desired time signature.

4. When you have set the value, press [ ] again. The HT-70 returns to its previous state. The [ ] switch stops ashing (either goes off or else comes on solid).

Changing the Accent

1. Hold down [ ] for at least one second. The switch begins ashing.

2. Press the [BELL()] switch. The switch lights up, and the multidisplay shows the current accent sound.

Display 1-2 2-2 1-4 2-4 3-4 4-4 6-8

Time signature 1/2 2/2 1/4 2/4 3/4 4/4 6/8

1, 4 2

3

3

1, 4 2

3

3

1, 4

2

3

3

13

1

3. Use [] or [] to set the desired accent sound.

* A bell tone is produced if you have set the metronome to sound like a pendulum; a digital tone is produced if you have set the metronome to have a digital sound (see Changing the Metronome Sound on page 14, below).

4. When you have set the value, press [ ] again. The HT-70 returns to its previous state. The [ ] switch stops ashing (either goes off or else comes on solid).

Changing the Metronome Sound

1. Hold down [ ] for at least one second. The switch begins ashing.

2. Press the [SOUND( )] switch. The switch lights up, and the multidisplay shows the current sound.

3. Use [] or [] to set the desired sound.

4. When you have set the value, press [ ] again. The HT-70 returns to its previous state. The [ ] switch stops ashing (either goes off or else comes on solid).

Additional Features In addition to the capabilities presented above, your HT-70 also provides a number of other useful performance-related features. For information, refer to the indicated pages.

Pitch control: refer to Adjusting the Pitch on page 18.

Temperament: refer to Choosing a temperament on page 18.

Brilliance: refer to Adjusting the brightness of the sound (Brilliance) on page 18.

Touch Control: refer to Changing the sensitivity of the keyboard on page 19.

Transpose: refer to Changing the key (Transpose) on page 19.

Restoring the factory settings: refer to Restoring the factory settings on page 19.

Display oFF on1 on2

Accent sound None Standard Bell or digital tone*

Display S1 S2

Sound Pendulum Digital

1, 4

2

3

3

4

Recording and playing back your performance The HT-70 provides a recorder that can record and play back your key- board performance as easily as when using a tape recorder. There are two recording parts. You can use these to record separate songs, or use them to separately record the right- and left-hand parts of the same song and then play back both parts simultaneously.

When you record onto a previously-recorded part, the previous data will be erased and overwritten by the newly-recorded performance. Before you continue, make sure that you dont mind losing the previously- recorded performance.

You can continue to save recorded performances until the memory becomes full.

Recording your performance When you complete a recording or editing session, please wait for the HT-70 to nish writing the new data to nonvolatile memory before turning the power off. Turning the power off while writing is in progress may result in loss or corruption of recorded songs, data, and settings.

Quick Recording (Recording a New Song) The onboard recorder is very easy to use. Lets start by making a quick recording.

1. Turn the sound selector to select the sound to be recorded.

2. Press [] and [ ] at the same time.

[] switch lights up, and [PART 1] and [PART 2] start ashing.

3. A currently empty user song number appears, ashing, on the multid-

isplay.

If there are no more free song numbers available, the already used number U01 appears, solid, in the display.

4. If you wish to save the recording to a different song number, press

[] or [] as necessary. You may choose any number from U01 to

U99.

Song numbers that are currently empty will appear ashing on the multidisplay. Numbers that are already in use will appear solid.

If you select a song number that is already in use, the new recording will overwrite the existing recorded song.

5. To start recording, hit a key on the keyboard or else press [ ].

You can also start recording by sending a MIDI message to the selected MIDI channel (p.20).

If you want to record in time with the metronome, hold down [ ] (so that it lights up) and press [ ]. The HT-70 will count out a two-measure pick-up and then automatically start record- ing. (For information about how to set the time signature, tempo, and other metronome features, see Changing the Met- ronome Settings on page 12.)

6. To end the recording, press [], [ ], or [].

The [PART 1] switch goes dark, and [PART 2] lights up solid.

When you end the recording, the HT-70 automatically writes the new data into nonvolatile song memory. During this time, the multidis- play will indicate that writing is in progress.

To Add Performance Data to Song Recorded by Quick Recording

If you have changed the song selection after making your quick recording, you must rst change the selection back again before you can add to the recording. To change back to the song, carry out steps 1 to 4 under To Add Performance Data to a Recorded Song, below.

1. Press [].

The [] switch lights up.

2. If necessary, turn the sound selector to select the sound to be

recorded.

3. Press [PART 1] one or more times, until it starts ashing.

4. To start recording, hit a key on the keyboard or else press [ ].

5. To end the recording, press [], [ ], or [].

The [PART 1] switch lights up solid, and the HT-70 automatically writes the recorded data into nonvolatile song memory. During write processing, the multidisplay will indicate that writing is in progress.

Recording a Performance

To Create and Record to a New Song You can start a quick recording by pressing [] and [ ] at the same time (see page 15 Quick Recording (Recording a New Song) ). If no user songs are currently in memory, you can also start quick record- ing by pressing [] by itself.

An E07 will appear on the multidisplay if user song memory becomes full. If you wish to save more recorded data, you must rst delete one or more existing user songs (p.16).

To Record to an Existing Song The onboard recorder holds two parts for each song. When you make a quick recording without pressing either the [PART 1] or the [PART 2] switch, the recording automatically records to Part 2. This means that you can later record additional performance data into Part 1 for that song. In general, you may have numerous user songs where only one part is recorded. You are always free to record more data into the empty parts of these songs. You may also have numerous two-part songs recorded. Again, you are free to over-record either part at any time, or to delete either part (p.16) and then record it again later. The status of each part is indicated by the indicator lamp in the corre- sponding PART switch, as follows.

To Add Performance Data to a Recorded Song 1. Press [SONG].

The [SONG] LED lights up.

2. Press [] or [] as necessary to select the user song to record to.

To help make your selection, you can audition each selected song by pressing [ ].

3. Press [SONG] again.

The [SONG] LED goes dark.

4. Press [].

The [] switch lights up. The PART switch for the already recorded part will be lit solid. Press the dark PART switch one or more times, until it starts ashing.

[PART 1] / [PART 2] Switch Status of Part

Dark The part is empty or muted. This part is not ready to record.

Lit solid The part contains recorded data. This part is not ready to record.

Flashing This part is ready to record.

15

1

If both parts of the song are recorded, you need to erase one of the parts before you can record more data to the song (refer to Deleting a Part on page 16).

5. If you wish to save the recording to a different song number, press

[] or [] as necessary. You may choose any number from U01 to

U99.

Song numbers that are currently empty will appear ashing on the multidisplay. Numbers that are already in use will appear solid.

If you select a song number that is already in use, the new recording will overwrite the existing recorded song.

6. To start recording, hit a key on the keyboard or else press [ ].

7. To end the recording, press [], [ ], or [].

When you end the recording, the HT-70 automatically writes the new data into nonvolatile song memory. During this time, the multidis- play will indicate that writing is in progress.

Important Information about Recording

When you record new performance data to the empty part of a recorded song, the resulting song length (in measures) will be the length of the longer part.

The performance is recorded using the sound selected by the sound selector while recording is in progress (while the [] switch is lit solid). You can use the selector to change the sound during the pick- up or any time during actual recording (while the PART switch is ashing and the [] switch is lit solid).

If you change the tempo while recording is in progress, the tempo change is included in the recording.

To change the tempo during recording: Press [DISPLAY] as necessary until the TEMPO LED lights up, and then use [] or [] to change the tempo value shown on the multidisplay.

You can record a time signature, but you cannot change this time sig- nature after the song has been recorded. If you are adding to an exist- ing recording, you can use a different time signature for the additional part.

To set the start measure for a recording: Before beginning the record- ing, press [DISPLAY] as necessary until the MEASURE LED lights up, and then use [] or [] to change the measure number on the multidisplay.

Saving a Recorded Song When you complete a recording, the HT-70 automatically saves the recorded performance data into a user song. For the song name, the HT-70 uses the number selected when recording was started.

The HT-70 can save up to 99 user songs. Each song can hold up to 999 measures, and up to 45,000 notes.

Copying a Song The HT-70 automatically stores the recorded data into the song number selected at the time of recording. You cannot select a different song num- ber when recording is nished. If you wish, however, you may copy the stored song into a different location (song number).

1. With the recorder stopped, press [FUNC.].

The [FUNC.] LED lights up.

2. Press [DISPLAY], so that SAv appears on the multidisplay.

When you release the switch, the multidisplay will show the destina- tion song number.

3. Press [] or [] as necessary to select the desired destination song

number.

The multidisplay shows the selected song number. Currently unas- signed numbers are shown ashing; numbers that are already in use for another song are shown solid.

If you save into a song number that is already used for another song, that song will be overwritten and lost. Be careful to avoid overwriting songs that you wish to keep.

4. Press [].

The HT-70 writes the song data into memory. The multidisplay shows the writing is in progress.

5. When the song has been saved (when the multidisplay no longer

shows that writing is in progress), press [FUNC.] again.

The [FUNC.] LED goes dark and the HT-70 returns to its previous state.

Deleting a Song 1. With the recorder stopped, press [FUNC.].

The [FUNC.] LED lights up.

2. Press [DISPLAY] one or more times, until dEL appears on the multi-

display.

When you release the switch, the multidisplay shows the current user song number.

3. Press [] or [] as necessary to select the song you wish to delete.

4. Press [] to delete the song.

The multidisplay indicates that writing is in progress as the song is deleted.

5. When deletion is completed (when the multidisplay no longer shows

that writing is in progress), press [FUNC.] again.

The [FUNC.] LED goes dark, and the HT-70 returns to its previous state.

Deleting a Part 1. With the recorder stopped, press [FUNC.].

The [FUNC.] LED lights up.

2. Press [DISPLAY] several times, until P.dL appears on the multidis-

play.

When you release the switch, the multidisplay shows part informa- tion.

3. Press [] or [] as necessary to select the part(s) to be deleted.

4. Press [] to delete the part(s).

The multidisplay indicates that writing is in progress as the song is deleted.

5. When deletion is completed (when the multidisplay no longer shows

that writing is in progress), press [FUNC.] again.

The [FUNC.] LED goes dark, and the HT-70 returns to its previous state.

To See How Much More Data Can Be Recorded If you press [FUNC.] while recording or while standing by to record (that is, whenever the [] LED is lit), the multidisplay will show the per- centage of space still remaining. The display will remain visible for about ve seconds. If 100% of space is still available, you have room to record approximately 45,000 notes within as many as 999 measures. If you wish to retain performance data over the long term, it is recom- mended that you use a USB connection to save and manage your data (p.23).

Display ALL P1 P2

Part(s) Both parts Part 2 Part 2

6

Playing Songs Selecting a Song 1. Press [SONG].

The [SONG] switch and the [DISPLAY] switchs SONG LED light up. The multidisplay shows the user song number.

The rst time you press [SONG] following power-on, the multid- isplay shows the lowest song number that contains a song.

If you have already selected one or more songs during the current session, the multidisplay shows the song number of the most recently selected song.

If no user songs exist in memory, the multidisplay shows ---.

2. Press [] or [] as necessary to select the desired song number on

the multidisplay.

3. Press [ ] to start play.

The HT-70 starts play of the selected song.

Playing of Song Parts When you select a song to play, one or both PART switches will light up, indicating that the corresponding part contains performance data. If a PART switch stays dark, this means that the part is empty. During play, you can fully or partially mute the playback from a non-empty part by pressing the corresponding PART button (so that the PART switch goes dark).

How to Set the Sound Level for a Muted Part

1. With the [SONG] LED lit, press [FUNC.].

The [FUNC.] LED lights up.

2. Press the PART switch for the part you wish to mute.

The switch goes dark.

3. Press [DISPLAY] several times, until P.Lv appears on the multid-

isplay.

When you release the switch, the multidisplay shows the current level setting. (The factory setting is 30.)

4. Press [] or [] as necessary to set the desired level.

You can set the value from 00 (full mute) to 90.

5. Press [FUNC.] again to complete the setting.

The [FUNC.] LED goes dark.

Pausing Song Play 1. Press [ ] during song play to pause the playback.

The switch starts ashing.

2. Press [ ] again to resume playback.

The switch comes on solid, and the TEMPO LED ashes in sync with the tempo.

Restarting a Playing Song 1. Press [] during song play to stop the song.

The song position returns to the beginning of the song.

2. Press [ ] to start song play from the beginning.

Changing the Tempo of a Playing Song 1. Press [DISPLAY] several times, until the TEMPO LED lights up.

The multidisplay shows the current tempo value.

2. Press [] or [] as necessary to adjust the tempo.

Press briey to change the value by 1, or hold the switch down to change continuously. The available range is ( =) 4 to 250.

Moving to a Different Position (Measure) 1. Press [DISPLAY] several times, until the MEASURE LED lights up.

The multidisplay shows the current measure number.

2. Press [] or [] as necessary to select a different measure.

3. If you move to a different measure while playback is stopped, the

song state will change from stopped to paused (and ( ) will start

ashing). You can then start play from the new position pressing

( ).

You can return to the start position of user a song (measure 001) by pressing [] and [] at the same time.

To Repeat Play of a Specied Song Segment (AB Repeat)

You can set up repeated play of a specied segment of the song. You dene the segment by its start measure and end measure. Proceed as fol- lows.

1. With the [SONG] LED lit, press [FUNC.].

The [FUNC.] LED lights up.

2. Press [DISPLAY] several times, until Ab.r appears on the multidis-

play.

When you release the switch, the multidisplay shows the repeat ON/ OFF setting. (The factory setting is oFF.)

3. Press [] or [] to turn the repeat feature on.

A dot appears at the bottom right corner of the multidisplay.

4. Press [DISPLAY] again, so that A. appears on the multidisplay.

When you release the switch, the multidisplay shows the current start measure. (The factory setting is 001.)

5. Press [] or [] as necessary to select the desired start measure.

6. Press [DISPLAY] again, so that b appears on the multidisplay.

When you release the switch, the multidisplay shows the current end measure. (The factory setting is 001.)

7. Press [] or [] as necessary to select the desired end measure.

8. Press [FUNC.] to complete the setting.

The [FUNC.] LED goes dark.

9. Press [ ] to start repeat play. Play will start at the start measure,

continue to the end measure, and then return to the start measure

and continue looping.

The dot at the bottom right of the multidisplay stays on solid while playback is within the AB repeat range, and ashes if playback is moved outside of that range.

10.To cancel repeat play, press [] or [] (see Step 3) to turn the fea-

ture off.

The dot disappears from the multidisplay.

During AB repeat play, the dot at the lower right of the multidis- play remains visible while the display is showing tempo, song number, or measure (p.5). The dot is also visible while you are setting up song features (p.74).

The repeat feature turns off automatically (and start and end measures both return to 001) when you select a different song, begin recording, or start some other type of operation.

17

1

Additional Features As an electronic piano, the HT-70 offers numerous convenient features that you can easily use to adjust the instruments sound, characteristics, and operation.

Adjusting the Pitch The built-in pitch control function allows you to make ne adjustments to the HT-70s pitch. You can use this feature, for example, to adjust the HT-70 so that it is in tune with other instruments. You can adjust the pitch by up to 25.0 Hz, in 0.5Hz increments. Adjust- ment is made with respect to note A4, which has standard pitch of 440.0 Hz and can be adjusted over the range 415.0 Hz to 465.0.Hz.

1. Be sure that the [SONG] LED is off, and press [FUNC.].

The [FUNC.] LED lights up.

2. Press [DISPLAY] several times, until tUn appears on the multidis-

play.

When you release the switch, the multidisplay shows the last three digits of the current pitch setting. (The factory setting is 40.0.)

3. Press [] or [] as necessary to change the setting.

4. Press [FUNC.] to complete the setting.

The setting is stored and the [FUNC.] LED goes dark.

This setting is retained even while the power is off. When you press [FUNC.] after changing the setting, the HT-70 automatically writes the new setting into nonvolatile memory. During the write, the multidisplay will indicate that writing is in progress.

Do not turn the HT-70 power off while writing is in progress. Doing so may cause loss or corruption of memorized settings and song data.

Choosing a temperament The HT-70 lets you choose from several temperaments (scale tunings). Many classical compositions were composed in historical eras in which the notes of a keyboard scale were tuned somewhat differently than the equal temperament commonly used today. For historically authentic performances of such music, the HT-70 lets you choose the Werckmeister or Kirnberger historical temperaments as well as the equal temperament used on most modern keyboard instruments.

Werckmeister This is the Werckmeister III scale created by the German organist and music theoretician Andreas Werckmeister. This temperament was created in the late Baroque era to allow relatively free modulation between keys.

Kirnberger This is the Kirnberger III scale created by Johann Phillip Kirnberger in the early 18th century. This temperament is used mainly for tuning harpsichords.

Equal temperament This is the temperament used by virtually all modern keyboard instruments. In this temperament, every semitone is an equal dis- tance apart, allowing you to play consistently in any key.

1. Be sure that the [SONG] LED is off, and press [FUNC.].

The [FUNC.] LED lights up.

2. Press [DISPLAY] several times, until ScL appears on the multidis-

play.

When you release the switch, the multidisplay shows the current temperament setting. (The factory setting is 00.)

3. Press [] or [] as necessary to change the setting.

4. Press [FUNC.] to complete the setting.

The setting is stored and the [FUNC.] LED goes dark.

This setting reverts to its factory default (equal temperament) when you change the position of the sound selector and when you turn the power off.

The Piano 1 and Piano 2 sounds use stretched tuning. In compar- ison to the equal tempered pitched, stretched tuning slightly lowers the pitch of the low notes and slightly raises the pitch of the high notes in order to create a more natural-sounding resonance.

Adjusting the brightness of the sound (Brilliance) Use this feature to select the brightness of the sound.

1. Be sure that the [SONG] LED is off, and press [FUNC.].

The [FUNC.] LED lights up.

2. Press [DISPLAY] several times, until brL appears on the multidis-

play.

When you release the switch, the multidisplay shows the current bril- liance setting. (The factory setting is 02.)

3. Press [] or [] as necessary to change the setting.

4. Press [FUNC.] to complete the setting.

The setting is stored and the [FUNC.] LED goes dark.

This setting is retained even while the power is off. When you press [FUNC.] after changing the setting, the HT-70 automatically writes the new setting into nonvolatile memory. During the write, the

multidisplay will indicate that writing is in progress.

Display 15.0 ... 39.5 40.0 40.5 ... 65.0

Pitch (Hz) 415.0 ... 439.5 440.0 440.5 ... 465.0

Display 00 01 02

Setting Equal temperament Werckmeister Kirnberger

Display 01 02 03

Setting Mel low sound wi th decreased brightness

Normal brightness

Brighter sound

8

Do not turn the HT-70 power off while writing is in progress. Doing so may cause loss or corruption of memorized settings and song data.

Changing the sensitivity of the keyboard You can change the way in which the dynamics of the sound respond to the strength of your playing. This is called the Touch Control function. When you turn the power on, the normal (standard) touch setting is selected.

1. Hold down [FUNC.] for about one second.

The [FUNC.] LED begins ashing. 2. Press [DISPLAY] several times, until tch appears on the multidis-

play.

When you release the switch, the multidisplay shows the current sen- sitivity setting. (The factory setting is 02).

3. Press [] or [] as necessary to change the setting.

4. Press [FUNC.] to complete the setting.

The setting is stored and the [FUNC.] LED goes dark.

The setting returns to 02 when the power is turned off.

Changing the key (Transpose) By changing the HT-70s key (transposing) you can play along with another instrument or vocal using an easier key (e.g., one that has fewer black keys) or the key in which you learned the song. This is called the Transpose function. You can transpose the pitch over a range of eleven semitones.

1. Hold down [FUNC.] for about one second.

The [FUNC.] LED begins ashing. 2. Press [DISPLAY] several times, until trS appears on the multidis-

play.

When you release the switch, the multidisplay shows the current transpose setting. (The factory setting is 00).

3. Press [] or [] as necessary to change the setting.

4. Press [FUNC.] to complete the setting.

The setting is stored and the [FUNC.] LED goes dark.

The setting returns to 00 when the power is turned off.

To play the song a semitone higher You want the C

pitch to sound when you play the C key.

Set the key to C (01 on the multidisplay).

The result: When you play of the keyboard notes shown at left, the HT-70 produces the notes shown at right.

The song is in the key of B but you want to play it using the ngering of the key of G

The pitch of B is a minor third (three semitones) above G. This means that you want the D

pitch (three semitones higher) to sound when

you press the C key. Set the key to D

(03 on the multidisplay).

Restoring the factory settings If youve been selecting sounds and changing their settings, but would like to restore the HT-70 to its factory-set values, proceed as follows. This procedure will not clear the performance data youve recorded but will return all other settings to their factory-set condition. If you want to erase the performance data youve recorded, refer to Deleting a Song on page 16.

Before you continue, make sure that you really want to restore the factory settings.

1. Turn off the power.

2. While holding down the [ ] switch, turn on the power.

LFd appears on the multidisplay, and all settings return to their factory defaults.

Display 01 02 03

Touch Control setting

Light (even light play- ing can produce loud sounds)

Normal (the piano touch of a typical piano)

Heavy (youll need to play strongly to pro- duce loud sounds)

Display -11 ... -03 -02 -01 00 01 02 03 ... 11

key C ... A A B C C D D ... B

19

2

MIDI What is MIDI? MIDI (Musical Instrument Digital Interface) is a world-wide standard for exchanging performance-related data between electronic musical instruments and computers. You can use the HT-70 to play other MIDI-equipped instruments. When you do so, your sound selections and damper pedal operations etc. will also be transmitted as control data. You can also use another MIDI keyboard or sequencer (automatic play- back device) to control the HT-70 and play its internal tone generator. By combining multiple MIDI instruments you can enjoy creating more sophisticated ensembles. You can also save the HT-70s recorder data on an external storage device via MIDI. This section explains the MIDI-related operations and functions of the HT-70. If you would like to learn more about MIDI, please consult one of the many available introductory books on this subject.

Making MIDI connections Commercially available MIDI cables are used to transfer MIDI data. Connect these cables from the MIDI connectors of the HT-70 to the MIDI connectors of the external MIDI device with which you want to exchange data. There are two types of MIDI connector.

MIDI IN connector This connector receives MIDI messages. The MIDI IN connector lets you play the HT-70s sounds from an exter- nal MIDI device (e.g., MIDI keyboard or sequencer). Use a MIDI cable to connect the HT-70s MIDI IN connector to your external MIDI devices MIDI OUT connector.

MIDI OUT connector This connector transmits MIDI messages. The MIDI OUT connector lets you control an external MIDI device using the MIDI messages transmitted from the HT-70. Use a MIDI cable to con- nect the HT-70s MIDI OUT connector to your external MIDI devices MIDI IN connector.

MIDI channels When youve nished making connections, set the HT-70 to the same MIDI channel as the MIDI device to which youve connected it. There are sixteen MIDI channels, numbered 116.

The channel setting returns to C01 when the power is turned on.

1. Hold down [FUNC.] for about one second.

The switchs LED begins ashing.

2. Press [DISPLAY] several times, until Ch appears on the multidis-

play.

When you release the switch, the multidisplay shows the current set- ting. (The factory setting is C01).

3. Press [] or [] as necessary to change the setting.

4. Press [FUNC.] to complete the setting.

The setting is stored and the [FUNC.] LED goes dark.

The HT-70 can record MIDI data coming in over the selected MIDI chan- nel.

Using the HT-70 as a multi-timbral sound module When you turn on the power of the HT-70, its internal sound generator is operating as a 16-part multi-timbral sound module that can be played from an external MIDI device.

1. Use a MIDI cable to connect the HT-70s MIDI IN to the MIDI OUT of

your sequencer or similar device.

2. Receive MIDI messages from the connected sequencer etc.

For details on how to transmit data from the sequencer youve con- nected, refer to the owners manual for the equipment youre using.

If the HT-70 is receiving program change messages together with perfor- mance data, it will change the sound (timbre) to accord with incoming program numbers as the performance proceeds. Note that this can occur only if the program change lter is off for the relevant MIDI channel. Note, however, that the selected MIDI channel (p.20) ignores program changes.

Filtering resets to OFF when the HT-70 power is turned on.

1. Hold down [FUNC.] for about one second.

The switchs LED begins ashing.

2. Press [DISPLAY] several times, until 16t appears on the multidis-

play.

When you release the switch, the multidisplay shows the current set- ting. (The factory setting is on).

3. Press [] or [] as necessary to change the setting.

4. Press [FUNC.] to complete the setting.

The setting is stored and the [FUNC.] LED goes dark.

The sound selector cannot be used to change sounds while the HT- 70 is playing externally supplied MIDI data. But note that it is pos- sible for the selected MIDI channel (p.20).

Local on/off setting You should turn the HT-70s Local setting off if you want the keyboard of the acoustic piano to which the HT-70 to play only an external MIDI- connected sound module and not the HT-70s internal sound generator, or to prevent duplicate notes from sounding when youve connected the HT-70 to a sequencer that echoes-back (re-transmits) the incoming data back to the HT-70. Normally you will leave the HT-70s Local setting on so that it will produce sound when you play the keyboard.

Immediately after the power is turned on, the Local setting will automatically be turned on.

1. Hold down [FUNC.] for about one second.

The switchs LED begins ashing.

2. Press [DISPLAY] several times, until L.ct appears on the multidis-

play.

When you release the switch, the multidisplay shows the current set- ting. (The factory setting is on).

3. Press [] or [] as necessary to change the setting.

4. Press [FUNC.] to complete the setting.

The setting is stored and the [FUNC.] LED goes dark.

Display C01 ... C16

Channel 1 ... 16

Display on oFF

Multi timbra on off

Display on oFF

Local on off

0

Program changes These messages can be sent by the HT-70 to select program numbers on an external MIDI device, or received from a connected MIDI device to switch program numbers on the HT-70.

Transmitting program changes Program numbers on a connected external MIDI device can be switched from the HT-70.

When you change the setting of the sound selector, the HT-70 will send out the corresponding program change number. The correspon- dences are shown in the table in the next section.

Receiving program changes When the HT-70 receives a program change number from an external device, its multi-timbral sound generator will change programs as shown in the table below. Note, however, that the selected MIDI channel (p.20) ignores program changes.

The HT-70 will change sounds (timbres) in accordance with received program change numbers indicated in the table below. If the remote MIDI devices send the HT-70 a program change number not included in the list below, the HT-70 will stop generating MIDI sound.

Program Change Filter Set the lter ON if you wish to disable sending and receiving of program change information. Set the lter OFF if you wish to enable transmission of this information.

Filtering resets to OFF for all MIDI channels when the power is turned on.

1. Hold down [FUNC.] for about one second.

The switchs LED begins ashing.

2. Press [DISPLAY] several times, until PC appears on the multidis-

play.

When you release the switch, the multidisplay shows the current set- ting. (The factory setting is oFF).

3. Press [] or [] as necessary to change the setting.

4. Press [FUNC.] to complete the setting.

The setting is stored and the [FUNC.] LED goes dark.

Control Change Filter Control change messages send information that is used to set the opera- tion of controllers such as the damper pedal. External MIDI devices use these messages to control the operation on the HT-70, and the HT-70 uses them to control the operation on external MIDI devices.

Set the lter OFF if you wish to enable sending and receiving of control change messages. Set the lter ON if you wish to disable transmission of this information.

Filtering resets to OFF for all MIDI channels when the power is turned on.

1. Hold down [REVERB] for about one second.

The switchs LED begins ashing.

2. Press [DISPLAY] several times, until CC appears on the multidis-

play.

When you release the switch, the multidisplay shows the current set- ting. (The factory setting is oFF).

3. Press [] or [] as necessary to change the setting.

4. Press [FUNC.] to complete the setting.

The setting is stored and the [FUNC.] LED goes dark.

Single Bank# PC# Sound

00 00 PIANO1

01 00 PIANO2

00 04 E.PIANO1

00 05 E.PIANO2

00 06 HARPSI.

00 19 P.ORGAN

00 16 E.ORGAN

00 48 STRINGS

Display on oFF

Program change lter on off

Display on oFF

Contorl change lter on off

21

2

USB Using MIDI through a USB Connection The HT-70 allows you to carry out MIDI communications with a com- puter directly through a USB connection. This eliminates the need for using MIDI cable and a separate MIDI interface device to make the con- nection. Once the connection has been made, you can use the HT-70, for example, as a MIDI sound generator or MIDI keyboard.

Connecting to a Computer Where possible, you should use the KORG USB-MIDI Driver when con- necting to a computer by USB. Specically, you should use the driver whenever connecting to a computer that provides the necessary support.

Computer environments that support the KORG USB- MIDI Driver are as follows. Windows:

Computer: Must have an onboard USB port, and must run Microsoft Windows XP or Microsoft Windows Vista.

Operating System: Microsoft Windows XP / Vista (Note: The Korg USB-MIDI Driver x64 editions is available in beta version only.)

Macintosh: Computer: Apple Macintosh with onboard USB port, running Mac OS X.

Operating System: Mac OS X 10.3 or above

Please be aware that meeting the above conditions does not guaran- tee that your computer will work with the HT-70. Some computers may not be usable for this purpose even though meeting the above requirements.

Please Note the Following Before Starting Use Copyright to all software supplied with this product is owned by Korg Inc. A software license agreement is provided separately. Please read the license before installing this software. Your installation of this soft- ware indicates your acceptance of this agreement.

Windows XP and Vista: Installing the KORG USB-MIDI Driver Please do not connect the HT-70 to the computer by USB cable until you have rst installed the KORG USB-MIDI Driver Tools. Proceed as fol- lows.

1. Insert the included CD-ROM into your computers CD-ROM drive.

In most cases, the KORG Digital Piano Application Installer will start automatically when you insert the CD-ROM. If your computer setup has disabled automatic start, please start the program by navigating to the CD-ROM and double-clicking Korg- Setup.exe.

2. Follow the instructions on your screen.

The installer will also install the KORG MIDI Data Filer. The Data Filer is not used by the HT-70.

3. Turn on the HT-70 power, and connect the HT-70 to the computer by

USB cable. The computer will then automatically install the Windows

standard USB MIDI driver.

You must now proceed to install the KORG USB-MIDI Driver for the USB port that you are using.

Installing the KORG USB-MIDI Driver for Windows 1. Install the KORG USB-MIDI Driver Tools as described above.

2. Restart the computer, turn on the power to the HT-70, and then con-

nect the computer and the HT-70 by USB cable.

The KORG USB-MIDI driver must be installed separately for each USB port you use it with. If you later decided to connect the HT-70 to a different USB port, you must repeat this proce- dure to install the driver for that port as well.

3. Select the following command from the taskbar to open the installa-

tion instructions: Start All Programs KORG KORG USB-MIDI

Driver Tools Installation Manual.

4. Follow the installation instructions on our screen to install the driver.

Driver Ports Keyboard Port: Used by the computer application to receive MIDI messages (key- board data and controller data) from the HT-70. Sound Port: Used by the computer application to send MIDI messages that drive the production of sound by the HT-70s internal tone generator.

Mac OS X: Installing the KORG USB-MIDI Driver Where possible, you should use the KORG USB-MIDI Driver when connecting to a computer by USB. Specically, you should use the driver whenever connecting to a computer that provides the neces- sary support.

Installing the KORG USB-MIDI Driver 1. Insert the included CD-ROM into your computers CD-ROM drive.

2. Open the CD-ROMs KORG USB-MIDI Driver folder, and double-

click KORG USB-MIDI Driver.pkg to start the installer. Then follow

the instructions on your screen.

Driver Ports Keyboard Port: Used by the computer application to receive MIDI messages (key- board data and controller data) from the HT-70. Sound Port: Used by the computer application to send MIDI messages that drive the production of sound by the HT-70s internal tone generator.

2

USB Mode The HT-70 supports transfer of data between its internal memory and an external computer. A USB connection is the most effective way of mak- ing such transfers. This capability is supported by Windows ME, Win- dows 2000, and all subsequent Windows versions, and by Mac OS 9.0.4 and above.

Before entering USB mode to transfer data to or from the HT-70, please be sure to close all MIDI applications at the computer side. Leaving a MIDI application running while USB transfer is in progress may result in corruption of data at the HT-70.

The HT-70 automatically restarts when you exit USB mode (by set- ting the mode oFF at the HT-70 side, by disconnecting the USB cable, by cutting the connection from the computer side, etc.). This means that any data and settings that have not yet been saved will be lost. Before entering USB mode, be sure to save all data and set- tings.

The USB connection cannot be used for MIDI communication while USB mode is being used for data transfer.

1. Connect the HT-70 and the computer with a USB cable.

2. Hold down [FUNC.] for about one second.

The switchs LED begins ashing.

3. Press [DISPLAY] several times, until USb appears on the multidis-

play.

When you release the switch, the multidisplay shows the current set- ting. (USB mode is set to oFF when the power rst comes on.)

While USB mode is on, most other operations are disabled. Only the following operations remain available: turning USB mode off, turning reverb on/off, turning metronome on/off, and use of the keyboard to play notes.

4. Press [] or [] to change the setting.

The HT-70 will automatically restart when you turn USB MODE off.

Exiting USB mode while USB data transfer is in progress (by setting the mode off at the HT-70 side, by disconnecting the USB cable, etc.) may cause corruption of data at the HT-70 side and may cause damage at the computer side.

Do not turn the HT-70 power off while USB mode is on. Doing so may cause corruption of data at the HT-70 side and may cause damage at the computer side.

5. Once you have set USB mode on, you can use the HT-70 just as any

other external USB drive. You can move les into it and out of it, and

you can use it to back up and restore your data.

HT-70 data is stored within subfolders under the KORG USER folder. Files within these folders may be given names of up to 128 characters.

6. When you have completed the data transfer, remove or delete the

USB drive from the computer desktop. For the details, refer to the

computers instruction manual.

If you are using Windows XP: When you remove or delete the USB drive, the HT-70 automatically returns to its initial (power-on) screen. (If you are using Windows Vista, after removing the USB drive at the computer side you must then press the switch at the HT-70 to return to the initial screen. If you are using a Mac OS: When you move KORG SSD into the Trash (or remove KORG SSD), the HT-70 automatically returns to its initial (power-on) screen.

Playing MIDI Files The HT-70 can recognize and play songs stored in the UserSong folder, provided that these songs are stored in standard MIDI format and that the lename consists of a U followed by two numerical digits (01 to 99) followed by the .mid le extension.

Examples: U07.mid, U34.mid

The HT-70 may not be able to correctly play standard MIDI les that use a time signature that cannot be set by the HT-70 itself.

Display on oFF

USB Mode ON (Mass storage) OFF (USB MIDI)

Folder Content

GLOBAL Global (common) settings

PRESET Sound presets

UserSong Songs recorded at the HT-70, and songs created at external sequencers. Any song that has been stored in standard MIDI format (le extension .MID) may be copied into this folder.

23

2

Appendix Troubleshooting

Power wont turn on

Is the DC plug of the AC adapter connected to the HT-70s DC12V connector?

Is the power cable of the AC adapter connected to an AC outlet of the correct voltage?

Is the power turned on? (p.8)

If the power still does not turn on, disconnect the AC adapter power cable from the AC outlet, and contact a service center.

No sound

Could the HT-70s [VOLUME] knob be turned all the way to the left (to immediately before the 0 position)? (p.8)

Is the selected part set to play back? (p.17)

Has performance data been recorded for the selected part? (p.15)

Could the selected part be muted? (p.17)

Make sure that the Local setting is ON (p.20).

Could the multi-display have an error indication (E01)? If so, an error has occurred in the cable that connects the piano with the HT-70 unit. Please contact a certied installation techni- cian or your dealer for service. The error display (E01) will disap- pear if you press the [] or [] switch.

Does error E04 appear on the multidisplay? If so, please contact your dealer or a qualied installation techni- cian for assistance. To clear the error display (E04), press [] or [].

If the multi-display indicates E02

The installation data for the unit has been lost, so the default data has been loaded. You may continue playing the HT-70, but the volume, pitch, and pedal action may be inaccurate. Please contact a certied installa- tion technician or your dealer for servicing and readjustment. The error display (E02) will disappear if you press the [] or [] switch.

Notes are interrupted

You have exceeded the maximum polyphony. The HT-70 is designed to give priority to the notes that were played most recently, so if you exceed the maximum polyphony, previously-played notes will be turned off. The maximum polyphony for the Electric piano 1 sound is 80 notes. However since the other sounds use twice as much data for each note, their maximum polyphony is 40 notes. If youre using the damper pedal or are playing back recorded data, please be aware of the maximum polyphony and choose the appropriate sound for your situation.

The pitch or tone of the piano sounds wrong in some key regions

The HT-70s piano sounds replicate the sound of an actual piano as faithfully as possible. This means that in some regions of the keyboard, you may feel that the overtones seem stronger, or that the tone or pitch seems wrong. This is not a malfunction.

A specic key does not sound, is too loud, is too soft

The pedal action is insufcient or too strong

The pitch is different than the acoustic piano

Does error E03 appear on the multidisplay? If so, the HT-70 is not calibrated. Contact your dealer or qualied installation tech- nician for assistance.

If a specic key is not playing at all, or is playing too loudly or too softly, then there is probably a problem with the calibration. Con- tact your dealer or qualied installation technician for assistance.

The silencing unit may cause the above problems if it is not regu- larly maintained and adjusted by a certied installation techni- cian. We recommend that you have your piano tuned and adjusted once a year.

Keyboard Does Not Produce Sound When Played as Piano (If equipped with automatic muting unit)

Is the Muting Bar LED on the underside of the piano lit up? (p.7)

The electrically-driven muting bar may be stuck in place. As a temporary x, you can forcibly release the bar using the release hook included with the instrument.

Then call your dealer or a qualied service agent for advice.

Cant record

Is there enough free space on the recorder? (p.16, p.25)

When I re-record from the middle of a recording, the tempo or time signature is different for the recorded portion.

When you re-recorded, did you set the tempo and time signature to be the same as when you previously recorded? When recording over existing song data, the HT-70 can change the tempo but it cannot change the time signature. When adding new measures to existing songs, however, the HT-70 can change both meter and tempo (p.16).

Cant play back recorded parts 1 and 2 with indepen- dent tempo or time signature.

On the HT-70, parts 1 and 2 share the same tempo and time signa- ture. Playback will use the time signature of the part that was recorded rst (p.16).

My external device does not respond to transmitted MIDI data.

Make sure that the MIDI cable is connected correctly (p.20).

Make sure that the HT-70 is transmitting MIDI data on the same channel as your external device is receiving (p.20).

Muting bar Release hook

Release position

Muting position

4

25

Cant install the USB-MIDI Driver for Windows (when using Windows)

Make sure that the USB cable is connected correctly (p.20).

Make sure that the CD-ROM is correctly inserted in your CD drive.

Could the lens of your CD drive be dirty? Use a commercially available lens cleaner to clean the lens of your CD drive.

Are you attempting to install from a networked CD drive? You cant install the driver from a CD drive via a network.

Make sure that USB is available on your computer. On Windows XP, go to [Control Panel] [System] [Hardware] tab [Device Manager] to check for Universal Serial Bus Control- ler and USB Root Hub.

Was the HT-70 detected as an Unknown Device? On Windows XP, go to [Control Panel] [System] [Hardware] tab [Device Manager] to check this. If the HT-70 was not detected cor- rectly, it will appear as Other USB Device or Unknown Device. Reconnect the USB cable, and if the HT-70 appears again as Unknown Device, it was detected as an unknown device. Delete the Unknown Device, and reinstall the driver (p.22).

Software does not respond

Make sure that the USB cable is connected correctly (p.23).

Did you install the driver?

Make sure that the computer to which you connected the HT-70 has recognized it correctly. On Windows XP, use the Control Panel Sound and Audio Devices Properties ? Hardware to check this. On Mac OS X, go to Macintosh HD Application Folder Utility Folder Audio MIDI settings, choose the MIDI Devices tab page, and check whether the HT-70 is shown. Depending on the hardware of the computer youre using, it may be impossible for the HT-70 to be recognized via a USB connection.

Check the HT-70s assignments and the USB MIDI port assignments (p.22).

It may be that the connected device or software does not support the HT-70s functionality. Refer to the owners manual for your software or the device youve connected.

Using the HT-70 without silencing the acoustic piano The HT-70 is designed to let you silence the sound of the acoustic piano so that you can play and practice using headphones, but you can also use some of the HT-70s functionality without silencing the acoustic piano.

Practice the acoustic piano while listening to the metronome or a piano song. If you dont want your playing on the keyboard to be heard from the speakers, turn the Local setting off. (p.20 Local on/off setting)

Here are some of the possibilities:

Play the acoustic piano together (layered) with the sounds of the HT-70.

Since the HT-70s MIDI messages are transmitted even if you dont mute the acoustic piano, you can transmit MIDI messages as you play the acoustic piano for performances that are linked with other MIDI equipment.

On the model with speakers, the HT-70s sounds can be played from the speakers. However even on the model without speakers, you can con- nect commercially available amplied speakers to the line output jack and use your instrument in the same way.

Error Messages Most error messages will remain on the multidisplay for several seconds only. If an error message (such as E05 or E06) remains on the screen for a prolonged time, you can turn it off by pressing [] or [].

E05 Recording was automatically stopped because you attempted to record past the 999th measure of the song. The 999 recorded mea- sures remain in memory.

E06 Recording was automatically stopped when you attempted to record more than 45,000 notes to the song. The 45,000 recorded notes remain in memory.

E07 User song memory is full. To record more data, you must rst free up some space by deleting unnecessary song data. If necessary, save important song les to a computer or other external device before deleting the data.

E08 Cannot execute recording, because the user song could not load. Occurs after error E0b if you attempt to record.

E09 Attempt to save parameters or to edit song data failed. It is likely that the HT-70 requires service. Please contact the certied installation technician or your dealer for advice.

E0A Song has been write-disabled at the computer side. To edit the song at the HT-70 side, change its name and save it as a new song.

E0b Song le is too big, or le is incompatible. If you attempt to record, the display will change to error E08.

E00...EFF Sensor error. Please contact the certied installation technician or your dealer for advice.

Specications

* Specications and appearance are subject to change without notice for improvement.

Sound Processed with INFINITYTM

Sounds Eight sounds: Piano 1, Piano 2, Electric piano 1, Electric piano 2, Harpsichord, Pipe organ, Electric organ, Strings

Sound generator Stereo sampling sound generator

Maximum polyphony 80 notes

Effects Reverb (three levels), Brilliance (three levels)

Recorder Two parts, maximum 45,000 notes Tempo/metronome, Record, Play/Pause, Stop, Part 1, Part 2

Keyboard mode Single

Temperaments Three types (Equal temperament, Kirnberger, Werckmeister)

Touch control Three levels (light, standard, heavy)

Controls [VOLUME] knob, Sound selector, [SONG], [REVERB], [DISPLAY], [FUNC.], [], [], [ ], [], [], [ ], [PART 1], [PART 2] switches

Pedals *Damper, Sostenuto, *Soft *Half-pedaling supported

Connectors Headphone x 2, LINE OUT (stereo), MIDI (IN, OUT), USB

Power supply DC12V (included AC adapter)

Dimensions (W x D x H)

271 x 180 x 63 (mm)/10.67" x 7.09" x 2.48" (sound module only)

Weight 1.4 Kg/ 3.09 lbs. (sound module only)

Included items AC adapter, headphone, CD-ROM, external speakers (only model with speakers)

26

Prcautions Emplacement Lutilisation de cet instrument dans les endroits suiva- nts peut en entraner le mauvais fonctionnement.

En plein soleil Endroits trs chauds ou trs humides Endroits sales ou fort poussireux Endroits soumis de fortes vibrations A proximit de champs magntiques

Alimentation Branchez ladaptateur secteur fourni une prise sect- eur de tension approprie. Evitez de brancher ladaptateur une prise de courant dont la tension ne correspond pas celle pour laquelle lappareil est conu.

Interfrences avec dautres appareils lectriques Les postes de radio et de tlvision situs proximit peuvent par consquent souffrir dinterfrences la rception. Veuillez ds lors faire fonctionner cet appar- eil une distance raisonnable de postes de radio et de tlvision.

Maniement Pour viter de les endommager, manipulez les com- mandes et les boutons de cet instrument avec soin.

Entretien Lorsque linstrument se salit, nettoyez-le avec un chif- fon propre et sec. Ne vous servez pas dagents de net- toyage liquides tels que du benzne ou du diluant, voire des produits inammables.

Conservez ce manuel Aprs avoir lu ce manuel, veuillez le conserver soi- gneusement pour toute rfrence ultrieure.

Evitez toute intrusion dobjets ou de liquide Ne placez jamais de rcipient contenant du liquide prs de linstrument. Si le liquide se renverse ou coule, il risque de provoquer des dommages, un court-circuit ou une lectrocution.

Veillez ne pas laisser tomber des objets mtalliques dans le botier (trombones, par ex.). Si cela se produit, dbranchez lalimentation de la prise de courant et contactez votre revendeur ou un technicien quali pour obtenir de laide.

Note concernant les dispositions (Seulement EU) Quand un symbole avec une poubelle barre dune croix apparait sur le produit, le mode demploi, les piles ou le pack de piles, cela signie que ce produit, manuel ou piles doit tre dpos chez un reprsentant comptent, et non pas dans une poubelle ou toute autre dchetterie conventionnelle. Disposer de cette manire, de prvenir les dommages pour la sant humaine et les dommages potentiels pour l'environne-

ment. La bonne mthode d'limination dpendra des lois et rglements applicables dans votre localit, sil vous plat, con- tactez votre organisme administratif pour plus de dtails. Si la pile contient des mtaux lourds au-del du seuil rglement, un symbole chimique est afch en dessous du symbole de la pou- belle barre dune croix sur la pile ou le pack de piles.

REMARQUE IMPORTANTE POUR LES CLIENTS Ce produit a t fabriqu suivant des spcications svres et des besoins en tension applicables dans le pays o ce produit doit tre utilis. Si vous avez achet ce produit via linternet, par vente par correspondance ou/et vente par tlphone, vous devez vrier que ce produit est bien utilisable dans le pays o vous rsidez. ATTENTION: Lutilisation de ce produit dans un pays autre que celui pour lequel il a t conu peut tre dangereuse et annulera la garantie du fabricant ou du distributeur. Conservez bien votre rcpiss qui est la preuve de votre achat, faute de quoi votre produit ne risque de ne plus tre couvert par la garantie du fabri- cant ou du distributeur.

* Tous les noms de produits et de socits sont des marques commerciales ou dposes de leur dtenteur respectif.

27

Sommaire

Introduction ..................................................28 Principales caractristiques ..................................... 28

Parties et leurs fonctions ............................29 Panneau de commande........................................... 29

Panneau arrire ....................................................... 30

Prparatifs pour linterprtation et la lecture des morceaux de dmonstration ..31 Avant de commencer jouer................................... 31

Branchement de lalimentation ....................................31

Coupure du son du piano acoustique..........................31

Casque ........................................................................ 31

En cas de problme pour visualiser le panneau de commande.............32

Mise sous tension........................................................ 32

Rglage du volume ..................................................... 32

Ecoute des dmonstrations sonores ....................... 32 coute des sons de dmonstration .............................32

Utilisation du HT-70 pour la lecture............34 Slection dune sonorit ............................................ 34

Utilisation des pdales............................................. 34

Ajouter de la rverbration au son (Reverb)............ 35

Interprtation accompagne par le mtronome....... 36 Pour activer le mtronome ..........................................36

Modification des rglages du mtronome ...................36

Fonctionnalits supplmentaires ............................. 38

Enregistrement et reproduction de votre interprtation .....39 Enregistrement de votre interprtation.................39

Enregistrement rapide (Enregistrement dun nouveau morceau) ..............39

Enregistrement dune interprtation ........................39

Sauvegarde dun morceau enregistr .......................40

Suppression dun morceau......................................40

Suppression dune partie.........................................40

Affichage de la quantit de donnes supplmentaires pouvant tre enregistres ..........40

Lecture de morceaux ...........................................41 Slection dun morceau ...........................................41

Pause de lecture dun morceau...............................41

Reprise de la lecture dun morceau.........................41

Modification du tempo dun morceau en cours de lecture ..............41

Passage une position (Mesure) diffrente ............41

Lecture rpte dun segment particulier dun morceau (Lecture rpte AB) ...41

Fonctionnalits supplmentaires ...............42 Rglage de la hauteur tonale...............................42

Choix dun temprament......................................42

Rglage de la brillance du son (Brilliance).......... 42

Changement de la sensibilit du clavier.............. 43

Changement de cl (Transpose)......................... 43 Pour jouer le morceau un demi-ton plus haut ......... 43

Le morceau est dans la cl de Bb mais vous souhaitez le jouer en utilisant le doigt de la cl de G.............. 43

Restauration des rglages dusine...................... 43

MIDI ............................................................... 44 Quest-ce que MIDI?................................................ 44

Effectuer des raccordements MIDI .......................... 44

Canaux MIDI............................................................ 44

Utilisation du HT-70 comme module sonore multitimbral.................... 44

Activation/dsactivation de Local............................. 44

Changements de programme .................................. 45

USB ............................................................... 46 Utilisation de MIDI via une connexion USB ............. 46

Mode USB ............................................................... 47

Appendice..................................................... 48 Guide de dpannage ............................................... 48

Utilisation du HT-70 sans assourdir le piano acoustique .................... 49

Messages derreur ................................................... 49

Spcifications........................................................... 49

Liste des fonctions .............................................. 74 Metronome Functions ................................................. 74

General Functions #1 ................................................. 74

General Functions #2 ................................................. 74

General Functions #3 ................................................. 74

MIDI implementation chart....................................... 75

Conventions de ce manuel du propritaire Commutateurs et touches

Les commutateurs et touches du HT-70 sont indiqus l'intrieur de crochets [ ]

(p.) : Indique une page de rfrence.

: Indique une fonction pour le modle avec haut-parleurs.

: Indique un avertissement pour l'utilisation du HT-70.

: Indique un conseil pour l'utilisation du HT-70.

2

Introduction

Principales caractristiques Large ventail de sonorits (p.34)

Choisissez parmi huit sonorits de haute qualit disponibles seulement chez Korg, y compris un grand piano de concert. Lchantillonnage stro vous permet de bncier dune sensation despace agrable en plus de la riche expressivit dun grand piano de concert.

Dix dmonstrations sonores (p.32) Dix dmonstrations intgres prsentent les diffrentes qualits de chaque sonorit.

Fonctions deffets (p.35, p.42) Effets de rverbration et de brillance inclus. Vous disposez de trois niveaux (profondeurs) pour rgler la rverbration de chaque voix. Utilisez les paramtres de brillance pour rgler la brillance du son.

Effets de pdale (p.34) Les pdales du piano permettent de modier les sons internes du HT-70, avec des fonctionnalits similaires.

Fonction de mtronome (p.36) Le mtronome intgr peut faire lobjet de nombreux rglages : vous pouvez rgler, votre guise, la signature temporelle, le tempo, le volume et la sonorit et ajouter une tonalit de cloche ou une tona- lit numrique pour marquer les accents.

Fonction de rglage du toucher (p.43) La rponse dynamique du clavier est une des caractristiques les plus importantes dun piano, et le HT-70 vous permet de choisir parmi trois types diffrents de rponse dynamique.

Hauteur tonale rglage (p.42, p.43) Le contrleur de tonalit intgr vous permet deffectuer des rglages prcis de la hauteur tonale. La fonctionnalit de transposition vous permet de changer la tonalit an quelle corresponde la tona- lit dun autre instrument ou dun morceau particulier.

Tempraments (p.42) En plus du temprament gal ordinaire, vous pouvez choisir entre deux tempraments classiques (Werckmeister et Kirnberger) pour des performances historiquement exactes.

Enregistreur (p.39) Lenregistreur intgr du HT-70 vous permet denregistrer et de reproduire vos propres sessions.

Prises (p.30, p.44, p.46) Des prises LINE OUT, MIDI et USB sont disponibles, vous permettant de relier le HT-70 des appa- reils audio autres que des priphriques MIDI, ou un ordinateur.

8

Parties et leurs fonctions

Panneau de commande

1. Prises de casque Vous pouvez brancher un casque stro (jack 1/4") sur ces prises. Deux casques stro peuvent tre branchs simultanment.

Si vous utilisez le modle avec haut-parleurs et avez branch les haut-parleurs inclus, ceux-ci ne produiront pas de son si vous avez branch un casque.

2. Commutateur [POWER] Ce commutateur permet dalterner entre les tats ON (afchage clair) et OFF (veille).

En mode de veille linstrument continue dtre ali- ment. Pour compltement couper lalimentation, dbranchez le cordon dalimentation de ladapta- teur AC de la prise secteur.

3. Bouton [VOLUME] Il contrle le volume du son transmis par le casque et la prise de sortie de ligne (p.32).

Sur les modles avec haut-parleurs, il contrle aussi le volume des haut-parleurs.

4. Slecteur de sonorit Utilisez cette commande pour slectionner des sonorits (p.34). Vous avez le choix entre huit sonorits diffrentes : PIANO 1, 2, E.PIANO (piano lectrique) 1, 2, HARPSI. (clavecin), P.ORGAN (grandes orgues), E.ORGAN (orgue lectrique), et STRINGS (violons).

5. Commutateur et tmoin [SONG] Utilisez ce commutateur pour slectionner un mor- ceau jouer ou enregistrer. Appuyez simultan- ment sur ce commutateur et sur le commutateur [REVERB] pour jouer lune des huit dmonstrations sonores intgres (p.32).

6. Commutateur et tmoins [DISPLAY] Ce commutateur modie le contenu de lafchage. Le tmoin allum indique le contenu actuel. En mode Fonction, utilisez ce commutateur pour modier la valeur dun paramtre (p.74).

7. Tmoin TEMPO Clignote en rythme avec le morceau en cours dinterprtation et denregistrement.

8. Section de lenregistreur Utilisez ces boutons pour dmarrer, suspendre, reprendre et arrter la lecture ou lenregistrement (p.39) . Lorsque le tmoin [ ] clignote, utilisez ces boutons pour dnir les paramtres du mtronome : accent de cloche, tempo et sonorit du mtronome.

9. Commutateur et tmoin [REVERB] Ce commutateur permet de rgler leffet de rverb- ration (p.35). Appuyez simultanment sur ce commutateur et sur le commutateur [SONG] pour jouer lune des huit dmonstrations sonores int- gres (p.32 ).

10.Commutateur et tmoin [FUNC.] Permet de passer en mode Fonction, an de pou- voir excuter diffrents rglages et actions non lis linterprtation (sauvegarder ou supprimer un mor- ceau, slectionner un temprament, effectuer des rglages MIDI, etc.) (p.74).

11.Afchage Afche diffrents types dinformations, identies par le tmoin [DISPLAY] allum. Peut afcher le tempo du mtronome, le tempo de lenregistreur, le

43 11

5 6 7 8

9 12 13 1410

2

1

29

3

numro du morceau enregistr, la mesure du mor- ceau, etc..

12.Commutateurs [] et [] Utilisez ces commutateurs pour rgler les tempos du mtronome et de lenregistreur, ainsi que pour dnir la valeur des diffrents paramtres.

13.Commutateur [ ] Permet dactiver ou de dsactiver le mtronome. Maintenez le commutateur enfonc pour modier les rglages du mtronome (p.36).

14.[Commutateurs [PART 1] et [PART 2] Permettent de slectionner le morceau enregistrer ou lire (p.39). Lorsque le tmoin [ ] clignote, utilisez ces boutons pour dnir le volume, la signature temporelle et dautres paramtres.

Panneau arrire

1. Prises MIDI Vous pouvez relier ces prises des priphriques MIDI comme des synthtiseurs, des squenceurs ou des botes rythmes de manire envoyer et rece- voir des donnes (p.44). IN Cette prise reoit les messages MIDI. Reliez-la la prise MIDI OUT dun priphrique MIDI qui con- trlera le HT-70. OUT Cette prise transmet les messages MIDI. Reliez-la la prise MIDI IN dun priphrique MIDI que le HT-70 contrlera.

2. Prise USB Vous pouvez utiliser un cble USB pour relier directement cette prise votre ordinateur de manire transfrer des donnes (p.46).

3. Prise LINE OUT Vous pouvez relier cette prise la prise dentre de votre systme acoustique amplifi et couter le HT- 70 via le systme, ou bien la relier votre enregis- treur et enregistrer le son du HT-70. Utilisez un cble stro avec minijack.

Vous devez effectuer tous les raccordements avec les appareils hors tension. Si vous ne faites pas atten- tion, vous risquez dendommager le HT-70 ou le priphrique auquel il est raccord, ou provoquer un dysfonctionnement.

Les cbles de raccordement sont vendus spar- ment. Vous devez obtenir des cbles appropris pour votre quipement, disponibles dans le com- merce.

4. Prise DC12V Branchez ici ladaptateur secteur fourni (p.31).

5. Connecteur denceintes: Permet de raccorder les enceintes ddies.

Exemples

En cours dexcution dun morceau

Tempo

N du morceau

Mesure (emplacement dans le morceau)

Point allum/clignotant/teint Activ/Activ (hors gamme)/Dsactiv

En cours de lecture rpte AB

En cours dcriture dans la mmoire (Affichage cyclique)

2 43

5

1

0

31

Prparatifs pour linterprtation et la lecture des morceaux de dmonstration

Avant de commencer jouer

Branchement de lalimentation 1. Assurez-vous que le HT-70 est hors tension.

2. Raccordez le cordon dalimentation fourni ladaptateur secteur fourni, puis raccordez la che CC de ladaptateur au connecteur 12 V CC du HT-70.

Utilisez uniquement ladaptateur secteur fourni. Si vous utilisez un autre adaptateur secteur, cela risque dendommager lappareil.

Coupure du son du piano acoustique Utilisez le module de sourdine pour activer ou couper le son du piano acoustique. Le module de sourdine peut tre soit lectrique (Fig. 2.1), soit manuel (Fig. 2.2). Si le module de sourdine de votre instrument ne correspond aucune de ces gures, veuillez consulter votre revendeur ou un agent de maintenance quali pour obtenir des instructions dutilisation.

Toutes les fonctions du HT-70 sont disponibles, que le son du piano acoustique soit coup ou non. La section Utilisation du HT-70 sans assourdir le piano acoustique la page 49 dcrit plusieurs faons dutiliser le HT-70 en produisant le son du piano acoustique.

Mme si le son du piano acoustique est coup, il sera peut tre lgrement audible si vous jouez fortement un accord.

Si votre instrument est quip dun module de sourdine lectrique Pour couper le son du piano, appuyez sur le commutateur du module de sourdine situ la base du piano (Fig. 2.1), de sorte quil soit en position STOP. Le tmoin MUTING BAR sallume pour indiquer que le son est coup. Pour rtablir le son du piano acoustique, appuyez de nouveau sur le commutateur, de sorte quil soit en position FREE et que le tmoin steigne.

Ne dplacez pendant que vous jouez.

Si votre instrument est quip dun module de sourdine manuel Comme indiqu dans la g. 2.2, tirez le levier de coupure du son situ sur le panneau infrieur du piano vers vous, et abaissez le levier pour le verrouiller. Pour revenir au jeu d'un piano acousti- que conventionnel, remettez le levier dans sa position d'origine.

Ne dplacez pas ce levier pendant que vous jouez.

Casque Les prises de casque sont situes lavant des enceintes ( p.29). Ces prises prennent en charge les ches de casque stro standard. Deux prises de casque tant disponibles, deux personnes peuvent couter en mme temps le son du piano.

Sur le modle avec haut-parleurs, le branchement dun casque coupera le son des haut-parleurs inclus. Utilisez le casque si le son risque de gner vos voisins, comme lorsque vous pratiquez la nuit.

Panneau infrieur du piano (panneau arrire du HT-70)

vers une prise secteur Adaptateur secteurCble d'alimentation

pour adaptateur secteur

Fig.1

DC plug

Fig. 2.1

Fig. 2.2

3

2

Si votre casque utilise un adaptateur 1/4", saisissez la che de ladaptateur quand vous bran- chez ou dbranchez votre casque.

Quand vous utilisez un casque, vous devez protger vos oreilles en vitant une coute prolon- ge volume lev.

En cas de problme pour visualiser le panneau de commande Vous pouvez rgler langle pour une meilleure visualisation. Desserrez simplement le bou- lon et la vis de chaque ct (gauche et droit), rglez langle votre convenance, puis revissez.

Veillez bien revisser aprs avoir effectu le rglage.

Mise sous tension Appuyez sur la touche [POWER] pour mettre lappareil sous tension. Lafchage apparat la mise sous tension. Pour teindre, appuyez de nouveau sur [POWER], de sorte que lafchage devienne noir.

Lors de la mise sous tension, tous les paramtres qui ne sont pas stocks dans la mmoire reviennent leurs valeurs par dfaut. Les donnes dinterprtation enregistres restent dans la mmoire et ne sont pas perdues.

Rglage du volume Tournez le bouton [VOLUME] pour rgler le volume (Voir Fig. 4.).

Vous contrlerez ainsi le volume de sortie de la prise de casque. Tournez le bouton vers la gauche pour diminuer le volume, ou vers la droite pour laugmenter.

Sur le modle avec haut-parleurs, vous contrlerez aussi le volume du son produit par les haut- parleurs. Pour certaines sonorits, le son des haut-parleurs pourra tre dform si vous rglez le volume son niveau maximal.

Ecoute des dmonstrations sonores Le HT-70 inclut dix dmonstrations sonores conues pour souligner les caractristiques de ses huit diffrentes sonorits.

coute des sons de dmonstration Liste des sons de dmonstration

No. Sonorit Titre du morceau Compositeur

1 PIANO1 La Campanella F.Liszt

2 PIANO1 The Path Of Truth Jordan Rudess

3 PIANO1 Rhapsody in Blue G.Gershwin

4 PIANO2 Someone To Watch Over Me G.Gershwin

5 E.PIANO1 Ramble M.Sakaguchi

6 E.PIANO2 KORG Original KORG

7 HARPSI. Invention No.8 J.S.Bach

8 P.ORGAN Toccata in D moll J.S.Bach

9 E.ORGAN KORG Original KORG

10 STRINGS First Snow M.Sakaguchi

Boulon

Dessous du piano

Vis

Fig.3

Fig.4

Plus fort

Plus doux

1. Appuyez simultanment sur les commutateurs [SONG] et [REVERB]. Le commutateur [SONG] sclignote.

2. Utilisez le slecteur de sonorit pour choisir dans la liste ci-dessus le morceau que vous souhaitez entendre. La lecture du morceau de dmonstration slectionn com- mencera. Si vous ne slectionnez pas de morceau dans les trois secondes qui suivent, les mor- ceaux seront jous en succession, en commenant par le morceau de dmonstration 1. Quand le morceau de dmonstration 10 sera termin, la reproduction des morceaux de dmonstration reprendra partir du numro 1.

Pour slectionner la dmonstration 2 ou 3, rglez le slecteur sur Piano 1, puis appuyez sur [] ou [].

3. Quand le morceau de dmonstration slectionn sera termin, la lecture se poursuivra partir du morceau suivant.

4. En cours de lecture de dmonstration, vous pouvez utiliser le commutateur [ ] pour suspendre et reprendre la lecture. (Le tmoin du commutateur est xe en cours de lec- ture et clignote en cours de pause.) Si vous appuyez sur le commutateur [], la lecture sarrte et la position est rinitialise au dbut du morceau de dmonstration.

5. Pour arrter la lecture, appuyez sur le commutateur [SONG]. Les commutateurs [SONG] steindront, la lecture sarrtera.

Si vous souhaitez changer le son de dmonstration, utilisez le slecteur de sonorit. Par exemple, si le morceau de dmonstration numro 1 est reproduit, mais que vous souhaitez passer au numro 10, tournez simplement le slecteur de sonorit vers STRINGS. La lecture des morceaux de dmonstration reprendra partir du numro 10. Alternativement, et utiliser les touches [][] pour slectionner un morceau.

La lecture de la dmonstration commence automatiquement (le tmoin [ ] sallume) lorsque vous modiez la slection.

Pendant la lecture dun morceau de dmonstration, vous pouvez jouer le mme morceau sur le clavier, mais vous ne pouvez pas changer de sonorit.

Vous ne pouvez pas changer le rglage de Reverb pendant la lecture dun morceau de dmons- tration.

Vous ne pouvez pas changer le tempo dun morceau de dmonstration.

12

1, 4 2

2

33

3

Utilisation du HT-70 pour la lecture

Slection dune sonorit

Tournez le slecteur de sonorit pour slectionner une sonorit.

Utilisation des pdales La pdale de soutien, la pdale Sostenuto et la pdale de sourdine peuvent tre appli- ques aux sonorits du HT-70. Vous pouvez utiliser les pdales du piano acoustique pour rendre votre interprtation plus expressive.

Pdale de soutien Les notes seront soutenues tant que vous maintiendrez la pdale enfonce, crant ainsi une rsonance riche. La distance franchie par la pdale contrlera la profondeur de leffet (effet de demi-pdale).

Pdale Sostenuto Utilisez cette pdale pour ne soutenir que certaines notes. Lorsque vous appuyez sur cette pdale, toutes les notes actuellement joues sur le clavier seront soutenues. Les notes que vous jouerez une fois la pdale enfonce ne seront pas soutenues.

Pdale de sourdine Le son sera plus doux tant que vous maintiendrez la pdale enfonce. La distance fran- chie par la pdale contrlera la profondeur de leffet (effet de demi-pdale).

Sonorit Description

PIANO1 Un son de grand piano de la plus haute qualit avec une prsence superbe

PIANO2 Un son de concert grandiose, avec des graves riches

E.PIANO1 Un son lger et clair de piano lectrique

E.PIANO2 Un son vif de piano lectrique avec une bonne attaque

HARPSI. Un son de clavecin raliste et classique

P.ORGAN Un son solennel de grandes orgues

E.ORGAN Un son dorgue jazz funky

STRINGS Un son densemble avec violons et autres instruments cordes

4

Ajouter de la rverbration au son (Reverb) Vous pouvez ajouter de la rverbration (Reverb) au son pour crer lambiance spa- cieuse typique dune salle concert.

La rverbration est active ou dsactive chaque pression sur le commutateur [REVERB]. Lorsque vous modiez le rglage, le HT-70 inscrit le nouveau rglage dans la mmoire. Pendant ce temps, lafchage indique quune opration dcriture est en cours (p.29).

Ne mettez pas le HT-70 hors tension pendant lcriture. Cela risquerait dentraner la perte ou la corruption des rglages mmoriss ou des donnes de morceaux.

Rglage de la profondeur de rverbration

1. Maintenez le commutateur [REVERB] enfonc pendant environ une seconde. Le tmoin du commutateur commence clignoter.

2. Appuyez sur [] ou [] pour slectionner la profondeur souhaite. Lafchage indique le rglage actuel. Lafchage indique 01 (peu profonde), 02 (standard) ou 03 (profonde).

3. Une fois le rglage effectu, appuyez de nouveau sur [REVERB] pour revenir laf- chage dorigine. Lorsque vous modiez le rglage, le HT-70 inscrit le nouveau rglage dans la mmoire. Pendant ce temps, lafchage indique quune opration dcriture est en cours (p.29). Une fois lcriture termine, le tmoin [REVERB] sallume ou steint pour indiquer si la rverbration est active ou dsactive pour la sonorit slection- ne laide du slecteur de sonorit.

Ne mettez pas le HT-70 hors tension pendant lcriture. Cela risquerait dentraner la perte ou la corruption des rglages mmoriss ou des donnes de morceaux.

Si vous changez la sonorit ou si vous mettez lappareil hors tension avant que la nouvelle profondeur ne soit inscrite dans la mmoire, la profondeur de rverbration est restaure son rglage initial.

Vous pouvez activer/dsactiver le Reverb et dfinir les rglages de profondeur indpen- damment pour chaque sonorit. Avec les rglages dusine, les valeurs typiques pour cha- que sonorit sont utilises.

Les sonorits Piano 1 son simulant la rsonance des cordes dun piano acoustique, une faible quantit de Reverb restera, mme si vous dsactivez leffet.

35

3

Interprtation accompagne par le mtronome Utiliser le mtronome est pratique quand vous souhaitez jouer en suivant un tempo exact.

Pour activer le mtronome

1. Appuyez sur la touche [ ]. La touche [ ] sallumera.

2. Pour arrter le mtronome, appuyez de nouveau sur la touche [ ]. La touche [ ] steindra.

Modication des rglages du mtronome Les rglages dcrits ici ( lexception du tempo et de la signature temporelle) sont conservs mme aprs la mise hors tension. Si vous appuyez sur la touche [ ] aprs chaque modica- tion, le HT-70 enregistre automatiquement la nouvelle valeur dans la mmoire non volatile. Pendant ce temps, lafchage indique quune opration dcriture est en cours (p.29 ).

Ne mettez pas le HT-70 hors tension pendant lcriture. Cela risquerait dentraner la perte ou la corruption des rglages mmoriss ou des donnes de morceaux.

Modication du rglage du tempo

1. Maintenez la touche [ ] enfonce pendant environ une seconde Le commutateur commence clignoter.

2. Le tmoin TEMPO (en regard du commutateur [DISPLAY]) sallume et lafchage indi- que le rglage actuel du tempo Si le tmoin TEMPO ne sallume pas, appuyez sur [TEMPO ()].

3. Utilisez les touches [] ou [] pour slectionner le tempo de votre choix. Appuyez brivement pour modier la valeur par incrments d1 ou maintenez la tou- che enfonce pour une modication en continu. Pour restaurer le rglage par dfaut du tempo, appuyez simultanment sur les touches [] et []. Les rglages disponibles sont compris entre (=) 4 et 250.

4. Une fois la valeur rgle, appuyez de nouveau sur [ ]. Le HT-70 revient son tat prcdent. Le commutateur [ ] arrte de clignoter (il steint ou reste allum xement).

1, 2

1, 4

2

3

3

6

Modication du volume

1. Maintenez la touche [ ] enfonce pendant environ une seconde. Le commutateur commence clignoter.

2. Appuyez sur le commutateur [VOL. (PART 2)]. Le commutateur sclaire et lafchage indique le rglage actuel du volume.

3. Utilisez les touches [] ou [] pour slectionner le niveau de votre choix. Appuyez brivement pour modier la valeur par incrments d1 ou maintenez la tou- che enfonce pour modier le volume en continu. Les rglages disponibles schelonnent entre 0 et 127.

4. Une fois la valeur rgle, appuyez de nouveau sur [ ]. Le HT-70 revient son tat prcdent. Le commutateur [ ] arrte de clignoter (il steint ou reste allum xement).

Modication de la signature temporelle

1. Maintenez la touche [ ] enfonce pendant environ une seconde. Le commutateur commence clignoter.

2. Appuyez sur le commutateur [BEAT (PART 1)]. Le commutateur sclaire et lafchage indique le rglage actuel de la signature temporelle.

3. Utilisez les touches [] ou [] pour slectionner la signature temporelle de votre choix.

4. Une fois la valeur rgle, appuyez de nouveau sur [ ]. Le HT-70 revient son tat prcdent. Le commutateur [ ] arrte de clignoter (il steint ou reste allum xement).

Modication de laccent

1. Maintenez la touche [ ] enfonce pendant environ une seconde. Le commutateur commence clignoter.

2. Appuyez sur le commutateur [[BELL()]. Le commutateur sclaire et lafchage indique le rglage actuel de laccent de votre choix.

Afchage 1-2 2-2 1-4 2-4 3-4 4-4 6-8

Mesure 1/2 2/2 1/4 2/4 3/4 4/4 6/8

1, 4 2

3

3

1, 4 2

3

3

1, 4

2

3

3

37

3

3. Utilisez les touches [] ou [] pour slectionner laccent de votre choix.

* Un son de cloche est produit si vous avez rgl le mtronome pour quil sonne comme une horloge; un son numrique est produit si vous avez rgl le mtronome pour un son numrique (reportez-vous la section Modication du son du mtro- nome la page 38 ci-aprs.).

4. Une fois la valeur rgle, appuyez de nouveau sur [ ]. Le HT-70 revient son tat prcdent. Le commutateur [ ] arrte de clignoter (il steint ou reste allum xement).

Modication du son du mtronome

1. Maintenez la touche [ ] enfonce pendant environ une seconde. Le commutateur commence clignoter.

2. Appuyez sur le commutateur [SOUND( )]. Le commutateur sclaire et lafchage indique le rglage actuel de son.

3. Utilisez les touches [] ou [] pour slectionner.

4. Une fois la valeur rgle, appuyez de nouveau sur [ ]. Le HT-70 revient son tat prcdent. Le commutateur [ ] arrte de clignoter (il steint ou reste allum xement).

Fonctionnalits supplmentaires Outre les fonctionnalits prsentes ci-dessus, votre HT-70 vous offre galement de nom- breuses autres fonctionnalits utiles pour linterprtation. Pour plus dinformations, reportez-vous aux pages indiques.

Hauteur tonale: reportez-vous la section Rglage de la hauteur tonale la page 42.

Temprament: reportez-vous la section Choix dun temprament la page 42.

Brilliance: reportez-vous la section Rglage de la brillance du son (Brilliance) la page 42.

Sensibilit du clavier: reportez-vous la section Changement de la sensibilit du clavier la page 43.

Transpose: reportez-vous la section Changement de cl (Transpose) la page 43.

Restauration: reportez-vous la section Restauration des rglages dusine la page 43.

Afchage oFF on1 on2

Accent Aucun Standard Cloche ou son numrique*

Afchage S1 S2

Son Horloge Numrique

1, 4

2

3

3

8

Enregistrement et reproduction de votre interprtation Le HT-70 est muni dun enregistreur qui peut enregistrer et reproduire votre interprtation au clavier aussi facilement que si vous utilisiez un enr egistreur bande. Il y a deux pistes denregistrement. Vous pouvez utiliser celles-ci pour enregis- trer des morceaux spare, ou pour enregistrer sparment les parties pour la main droite ou la main gauche dun mme morceau, puis reproduire simultan- ment les deux parties.

Quand vous enregistrez par-dessus une partie dj enregistre, les donnes pr- cdentes seront effaces et remplaces par celles de linterprtation nouvelle- ment enregistre. Avant de continuer, assurez-vous que linterprtation enregistre prcdemment peut tre efface sans regret.

Vous pouvez sauvegarder les morceaux enregistrs jusqu ce que la mmoire soit sature.

Enregistrement de votre interprtation Aprs avoir termin une session denregistrement ou ddition, attendez que le HT-70 termine dcrire les nouvelles donnes dans la mmoire non volatile avant de le mettre hors tension. Si vous mettez le piano hors ten- sion en cours dcriture, cela risque dentraner une perte ou une corrup- tion des morceaux, donnes et rglages enregistrs.

Enregistrement rapide (Enregistrement dun nouveau morceau)

Lenregistreur intgr est trs facile utiliser. Commenons par un enregistre- ment rapide.

1. Tournez le slecteur de sonorit pour slectionner la sonorit enregistrer.

2. Appuyez simultanment sur [] et [ ]. Le commutateur [] sclaire et les tmoins [PART 1] et [PART 2] commen- cent clignoter.

3. Un numro de morceau utilisateur actuellement vide apparat et clignote sur lafchage. Sil ny a plus de numros de morceaux utilisateur libres, le numro dj uti- lis U01 safche, xement.

4. Pour sauvegarder lenregistrement sous un numro de morceau diffrent, appuyez sur [] ou []. Vous pouvez choisir un numro entre U01 et U99.

Les numros de morceaux actuellement vides clignotent dans laf- chage. Les numros dj utiliss sont xes.

Si vous slectionnez un numro de morceau dj utilis, le nouvel enregistrement crase le morceau dj enregistr.

5. Pour dmarrer lenregistrement, appuyez sur une touche du clavier ou appuyez sur [ ]. Vous pouvez galement dmarrer lenregistrement en envoyant un message MIDI au canal MIDI slectionn (p.44).

Pour enregistrer en rythme avec le mtronome, maintenez la touche [ ] enfonce (jusqu ce quelle sallume), puis appuyez sur [ ]. Le HT-70 compte deux mesures de pick-up, puis com- mence automatiquement lenregistrement.(Pour plus dinforma- tions sur les rglages de la signature temporelle, du tempo et dautres fonctionnalits du mtronome, reportez-vous la sec- tion Modication des rglages du mtronome la page 36.)

6. Pour mettre n lenregistrement, appuyez sur [], [ ] ou []. Le commutateur [PART 1] steint et le commutateur [PART 2] sallume xe- ment.

Lorsque vous arrtez lenregistrement, le HT-70 crit automatiquement les nouvelles donnes dans la mmoire de morceaux non volatile. Pendant ce temps, lafchage indique quune opration dcriture est en cours.

Ajout de donnes dinterprtation aux morceaux enre- gistrs via la fonction denregistrement rapide

Si vous avez modi la slection de morceau aprs lenregistrement rapide, vous devez dabord changer de nouveau la slection avant dajou- ter lenregistrement. Pour revenir au morceau, suivez les tapes 1 4 de la section Ajout de donnes dinterprtation un morceau enregistr ci- aprs.

1. Appuyez sur []. Le commutateur [] sallume.

2. Si ncessaire, tournez le slecteur de sonorit pour slectionner la sonorit enregistrer.

3. Appuyez sur le commutateur [PART 1] une ou plusieurs fois, jusqu ce quil clignote.

4. Pour dmarrer lenregistrement, appuyez sur une touche du clavier ou appuyez sur [ ].

5. Pour mettre n lenregistrement, appuyez sur [], [ ] ou []. Le commutateur [PART 1] sallume xement, puis le HT-70 crit automati- quement les donnes enregistres dans la mmoire de morceaux non vola- tile. En cours dcriture, lafchage indique quune opration dcriture est en cours.

Enregistrement dune interprtation

Cration et enregistrement dun nouveau morceau ous pouvez dmarrer un enregistrement rapide en appuyant simultanment sur [] et [ ] (voir page 39 Enregistrement rapide (Enregistrement dun nou- veau morceau)). Si aucun morceau nest actuellement enregistr, vous pouvez galement dmarrer un enregistrement rapide en appuyant uniquement sur [].

Lindication E07 apparat sur lafchage si la mmoire de morceaux utili- sateur est sature. Pour sauvegarder davantage de donnes enregistres, vous devez dabord supprimer un ou plusieurs morceaux utilisateur exis- tants (p.40).

Enregistrement dans un morceau existant Lenregistreur intgr divise chaque morceau en deux parties. Lorsque vous dmarrez un enregistrement rapide sans appuyer sur le commuta- teur [PART 1] ou [PART 2], lenregistrement dmarre automatiquement en Partie 2. Vous pouvez ainsi ensuite ajouter des donnes dinterprtation supplmentai- res dans la Partie 1 de ce morceau. En gnral, vous pouvez avoir plusieurs morceaux utilisateur avec une seule partie enregistre. Vous pouvez toujours enregistrer davantage de donnes dans les parties vides de ces morceaux. Vous pouvez galement avoir plusieurs morceaux avec les deux parties enregis- tres. L encore, vous pouvez craser lune de deux parties tout moment ou les supprimer (p.40), puis les enregistrer de nouveau ultrieurement. Le statut de chacune des parties est indiqu par le tmoin du commutateur PART, comme indiqu ci-dessous.

Ajout de donnes dinterprtation aux morceaux enre- gistrs 1. Appuyez sur [SONG].

Le commutateur [SONG] sallume.

2. Appuyez sur [] ou [] pour slectionner le morceau utilisateur vers lequel enregistrer. Pour faciliter la slection, vous pouvez couter chacun des morceaux slec- tionns en appuyant sur [ ].

3. Appuyez de nouveau sur [SONG]. Le tmoin [SONG] steint.

Commutateur [PART 1] / [PART 2]

Statut de la partie

Eteint La partie est vide ou le son est coup. La partie nest pas prte pour lenregistrement.

Allum xe La partie contient des donnes enregistres. La partie nest pas prte pour lenregistrement.

Clignotant La partie est prte pour lenregistrement.

39

4

4. Appuyez sur []. Le commutateur [] sallume. Le commutateur PART correspondant la partie dj enregistre est allum xement. Appuyez sur le commutateur PART teint une ou plusieurs fois, jusqu ce quil clignote.

Si les deux parties du morceau sont enregistres, vous devez suppri- mer lune des deux parties avant de procder lenregistrement de donnes supplmentaires dans le morceau (reportez-vous la section Suppression dune partie la page 40).

5. Pour sauvegarder lenregistrement sous un numro de morceau diffrent, appuyez sur [] ou []. Vous pouvez choisir un numro entre U01 et U99.

Les numros de morceaux actuellement vides apparaissent en cligno- tant dans lafchage. Les numros dj utiliss sont xes.

Si vous slectionnez un numro de morceau dj utilis, le nouvel enregistrement crase le morceau dj enregistr.

6. Pour dmarrer lenregistrement, appuyez sur une touche du clavier ou appuyez sur [ ].

7. Pour mettre n lenregistrement, appuyez sur [], [ ]] ou []. Lorsque vous arrtez lenregistrement, le HT-70 crit automatiquement les nouvelles donnes dans la mmoire de morceaux non volatile. Pendant ce temps, lafchage indique quune opration dcriture est en cours.

Informations importantes concernant lenregistrement

Lorsque vous enregistrez de nouvelles donnes dinterprtation dans la par- tie vide dun morceau enregistr, la longueur du morceau (en mesures) cor- respond la longueur de la partie la plus longue.

Linterprtation est enregistre avec la sonorit slectionne laide du slecteur de sonorit pendant lenregistrement (lorsque le commuta- teur [] est allum xement). Vous pouvez utiliser le slecteur pour modier la sonorit au cours de la phase de pick-up ou tout moment au cours de lenregistrement proprement dit (lorsque le commutateur PART clignote et que le commutateur [] est allum xement).

Si vous modiez le tempo pendant lenregistrement, la modication de tempo est incluse dans lenregistrement.

Pour modier le tempo pendant lenregistrement : appuyez sur [DISPLAY] autant de fois que ncessaire pour que le tmoin TEMPO sallume, puis utili- sez les touches [] ou [] pour modier la valeur du tempo afche.

Vous pouvez enregistrer une signature temporelle, mais vous ne pouvez pas la modier une fois le morceau enregistr. Si vous ajoutez des donnes un enregistrement existant, vous pouvez utiliser une signature temporelle diff- rente pour la nouvelle partie.

Pour dnir la mesure de dbut dun enregistrement : avant de com- mencer lenregistrement, appuyez sur [DISPLAY] autant de fois que ncessaire pour que le tmoin MEASURE sallume, puis utilisez les tou- ches [] ou [] pour modier le numro de la mesure sur lafchage.

Sauvegarde dun morceau enregistr Une fois un enregistrement termin, le HT-70 sauvegarde automatiquement les donnes dinterprtation enregistres dans un morceau utilisateur. Le HT-70 utilise le numro slectionn au dbut de lenregistrement pour nom- mer le morceau.

Le HT-70 permet de sauvegarder jusqu 99 morceaux utilisateur. Cha- que morceau peut comporter jusqu 999 mesures et 45 000 notes.

Copie dun morceau Le HT-70 sauvegarde automatiquement les donnes enregistres sous le numro du morceau slectionn au dbut de lenregistrement. Vous ne pouvez pas slec- tionner de numro diffrent une fois lenregistrement termin. Pour ce faire, vous pouvez toutefois copier le morceau sauvegard un emplacement (numro de morceau) diffrent.

1. Avec lenregistreur arrt, appuyez sur [FUNC.]. Le tmoin [FUNC.] sallume.

2. Appuyez sur [DISPLAY] de sorte que SAv apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le numro du morceau de destination.

3. Appuyez sur [] ou [] pour slectionner le numro du morceau de destina- tion de votre choix. Lafchage indique le numro du morceau slectionn. Les numros encore non affects clignotent, tandis que les numros dj utiliss pour un autre morceau sont xes.

Si vous sauvegardez lenregistrement sous un numro de morceau dj utilis, ce morceau sera cras et perdu. Evitez dcraser les morceaux que vous souhaitez conserver.

4. Appuyez sur []. Le HT-70 crit les donnes du morceau dans la mmoire. Lafchage indique que lcriture est en cours.

5. Une fois le morceau sauvegard (lafchage nindique plus que lcriture est en cours), appuyez de nouveau sur [FUNC.]. Le tmoin [FUNC.] steint et le HT-70 revient son tat prcdent.

Suppression dun morceau 1. Avec lenregistreur arrt, appuyez sur [FUNC.].

Le tmoin [FUNC.] sallume.

2. Appuyez sur [DISPLAY] une ou plusieurs fois, jusqu ce que dEL appa- raisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le numro du morceau utilisateur actuel.

3. Appuyez sur [] ou [] pour slectionner le morceau supprimer.

4. Appuyez sur [] pour supprimer le morceau. Lafchage indique que lcriture est en cours pendant la suppression du morceau.

5. Une fois la suppression termine (lafchage nindique plus que lcriture est en cours), appuyez de nouveau sur [FUNC.]. Le tmoin [FUNC.] steint et le HT-70 revient son tat prcdent.

Suppression dune partie 1. Avec lenregistreur arrt, appuyez sur [FUNC.].

Le tmoin [FUNC.] sallume.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que P.dL apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique les informations sur la partie.

3. Appuyez sur [] ou [] pour slectionner la/les partie(s) supprimer.

4. Appuyez sur [] pour supprimer la/les partie(s). Lafchage indique que lcriture est en cours pendant la suppression du morceau.

5. Une fois la suppression termine (lafchage nindique plus que lcriture est en cours), appuyez de nouveau sur [FUNC.]. Le tmoin [FUNC.] steint et lafchage revient son tat prcdent.

Afchage de la quantit de donnes suppl- mentaires pouvant tre enregistres

Si vous appuyez sur [FUNC.] en cours denregistrement ou de veille denregis- trement (lorsque le tmoin [] est allum), lafchage indique le pourcentage despace libre restant. Lafchage reste visible pendant environ cinq secondes. Si 100 % despace reste disponible, vous pouvez enregistrer environ 45.000 notes, dans 999 mesures. Pour conserver les donnes dinterprtation long terme, il est recommand dutiliser une connexion USB pour sauvegarder et grer vos donnes (p.47).

Afchage ALL P1 P2

Partie(s) Les deux Partie 1 Partie 2

0

Lecture de morceaux Slection dun morceau 1. Appuyez sur [SONG].

Le commutateur [SONG] et le tmoin [DISPLAY] du commutateur SONG sallument. Lafchage indique le numro du morceau utilisateur.

La premire fois que vous appuyez sur le commutateur [SONG] aprs la mise sous tension, lafchage indique le numro du morceau le plus bas contenant un morceau.

Si vous avez dj slectionn un ou plusieurs morceaux au cours de la session actuelle, lafchage indique le numro du morceau le plus rcem- ment slectionn.

Sil ny a pas de morceau utilisateur dans la mmoire, lafchage indique ---.

2. Appuyez sur [] or [] pour slectionner le numro du morceau de votre choix sur lafchage.

3. Appuyez sur [ ] pour lancer la lecture. Le HT-70 commence la lecture du morceau slectionn.

Lecture de parties des morceaux Lorsque vous slectionnez un morceau lire, un commutateur PART, ou bien les deux, sallume, indiquant que la partie correspondante contient des donnes dinterprtation. Si un commutateur PART ne sallume pas, cela signie que la partie est vide. En cours de lecture, vous pouvez totalement ou partiellement mettre en sourdine la lecture dune partie pleine en appuyant sur la touche PART correspondante (de sorte que le commutateur PART steigne).

Rglage du niveau sonore pour une partie en sourdine. 1. Avec le tmoin [SONG] allum, appuyez sur [FUNC.].

Le tmoin [FUNC.] sallume.

2. Appuyez sur le commutateur PART de la partie que vous souhaitez cou- per. Le commutateur steint.

3. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que P.Lv apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage de niveau actuel (Le rglage par dfaut est 30.).

4. Utilisez les touches [] or [] pour slectionner le niveau de votre choix. Vous pouvez dnir une valeur entre 00 (totalement coup) et 90.

5. Appuyez de nouveau sur [FUNC.] pour valider le rglage. Le tmoin [FUNC.] steint.

Pause de lecture dun morceau 1. Appuyez sur [ ] au cours de la lecture dun morceau pour linterrompre.

Le commutateur commence clignoter.

2. Appuyez de nouveau sur [ ] pour reprendre la lecture. Le commutateur est allum xement et le tmoin TEMPO clignote en rythme avec le tempo.

Reprise de la lecture dun morceau 1. Appuyez sur [] au cours de la lecture dun morceau pour larrter.

La position du morceau revient au dbut.

2. Appuyez sur [ ] pour dmarrer la lecture du morceau depuis le dbut.

Modication du tempo dun morceau en cours de lecture

1. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que le tmoin TEMPO sallume. Lafchage indique la valeur actuelle du tempo.

2. Utilisez les touches [] ou [] pour rgler le tempo. Appuyez brivement pour modier la valeur par incrments d1 ou mainte- nez la touche enfonce pour une modication en continu. Les rglages dis- ponibles sont compris entre ( =) 4 et 250.

Passage une position (Mesure) diffrente 1. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que le tmoin MEASURE

sallume. Lafchage indique le numro de la mesure actuelle.

2. Utilisez les touches [] ou [] pour slectionner une mesure diffrente.

3. Si vous passez une autre mesure alors que la lecture est arrte, ltat du morceau passe de larrt la pause (et ( ) commence clignoter). Vous pouvez alors lancer la lecture partir de la nouvelle position en appuyant sur ( ).

Vous pouvez revenir la position de dpart du morceau utilisateur (mesure 001) en appuyant simultanment sur [] et [].

Lecture rpte dun segment particulier dun morceau (Lecture rpte AB)

Vous pouvez congurer la lecture rpte dun segment particulier dun mor- ceau. Vous devez dnir la mesure de dbut et la mesure de n du segment. Pro- cdez comme suit.

1. Avec le tmoin [SONG] allum, appuyez sur [FUNC.]. Le tmoin [FUNC.] sallume.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que Ab.r apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique si la lecture rpt est active ou dsactive (Le rglage par dfaut est Dsactiv.).

3. Appuyez sur [] ou [] pour activer la fonction de lecture rpte. Un point apparat dans le coin infrieur droit de lafchage.

4. Appuyez de nouveau sur [DISPLAY] de sorte que A. apparaisse dans laf- chage. Lorsque vous relchez le commutateur, lafchage indique la mesure de dbut actuelle (Le rglage par dfaut est 001.).

5. Utilisez les touches [] or [] pour slectionner la mesure de dbut de votre choix.

6. Appuyez sur [DISPLAY] de sorte que b apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique la mesure de n actuelle (Le rglage par dfaut est 001.).

7. Utilisez les touches [] or [] pour slectionner la mesure de n de votre choix.

8. Appuyez sur [FUNC.] pour valider le rglage. Le tmoin [FUNC.] steint.

9. Appuyez sur [ ] pour lancer la lecture rpte. La lecture commence la mesure de dbut, continue jusqu la mesure de n, puis revient la mesure de dbut, et ainsi de suite en boucle. Le point dans le coin infrieur droit de lafchage reste xe tant que la lec- ture reste dans la plage de rptition AB et clignote si la lecture passe en dehors de cette plage.

10. Pour annuler la lecture rpte, appuyez sur [] or [] (voir ltape 3) pour dsactiver la fonction. Le point disparat de lafchage.

Au cours de la lecture rpte AB, le point dans le coin infrieur droit de lafchage reste visible lorsque le tempo, le numro du morceau ou la mesure est afch (p.29). Le point est galement visible lorsque vous congurez les caractristiques des morceaux (p.74).

La fonction de lecture rpte est automatiquement dsactive (les mesures de dbut et de n reviennent 001) lorsque vous slectionnez un morceau diffrent, que vous commencez lenregistrement ou toute autre opration.

41

4

Fonctionnalits supplmentaires En tant que piano lectronique, le HT-70 propose plusieurs fonctionnalits prati- ques que vous pouvez facilement utiliser pour rgler le son, les caractristiques et le fonctionnement de linstrument.

Rglage de la hauteur tonale La fonction de contrle de tonalit intgre vous permet deffectuer des rglages prcis de la tonalit du HT-70. Vous pouvez utiliser cette fonction pour, par exemple, rgler le HT-70 an de le syntoniser avec dautres instruments. Vous pouvez rgler la hauteur tonale jusqu 25,0 Hz, par incrments de 0,5 Hz. Le rglage se fait par rapport la note La4 , qui a une hauteur tonale stan- dard de 440,0 Hz et peut tre rgle entre 415,0 Hz et 465,0 Hz.

1. Vriez que le tmoin [SONG] est teint, puis appuyez sur [FUNC.]. Le tmoin [FUNC.] sallum.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que tUn apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique les trois derniers chiffres du rglage actuel de la hauteur tonale. (Le rglage par dfaut est 40,0.)

3. Utilisez les touches [] ou [] pour modier le rglage.

4. Appuyez sur [FUNC.] pour valider le rglage. Le rglage est enregistr et le tmoin [FUNC.] steint.

Ce rglage est conserv mme lorsque lalimentation est coupe. Si vous appuyez sur [FUNC] aprs avoir modi le rglage, le HT-70 enregistre automatiquement le nouveau rglage dans la mmoire non volatile. Pen- dant lcriture, lafchage indique quune opration dcriture est en cours.

Ne mettez pas le HT-70 hors tension pendant lcriture. Cela risquerait dentraner la perte ou la corruption des rglages et donnes de morceaux mmoriss.

Choix dun temprament Le HT-70 vous permet de choisir parmi plusieurs tempraments (rglages de gamme). De nombreux morceaux classiques ont t composs une poque o les notes du clavier taient accordes quelque peu diffremment du tempra- ment gal communment utilis de nos jours. Pour linterprtation historique- ment authentique dune telle musique, le HT-70 vous permet de choisir entre les tempraments Werckmeister, Kirnberger ou gal employ sur les instruments clavier plus modernes.

Werckmeister Il sagit de la gamme Werckmeister III cre par lorganiste allemand et tho- ricien de la musique Andreas Werckmeister. Ce temprament a t cr la n de lpoque baroque pour permettre une modulation relativement libre entre les touches.

Kirnberger Il sagit de la gamme Kirnberger III cre par Johann Phillip Kirnberger au dbut du 18me sicle. Ce temprament est utilis essentiellement pour accorder des clavecins.

Temprament gal Il sagit du temprament utilis par pratiquement tous les instr uments modernes clavier. Dans ce temprament, chaque demi-ton se trouve une distance gale du prcdent ou du suivant, vous permettant ainsi de jouer rgulirement dans nimporte quelle cl.

1. Vriez que le tmoin [SONG] est teint, puis appuyez sur [FUNC.]. Le tmoin [FUNC.] sallume.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que ScL apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage actuel du temprament. (Le rglage par dfaut est 00.)

3. Utilisez les touches [] ou [] pour modier le rglage.

4. Appuyez sur [FUNC.] pour valider le rglage. Le rglage est enregistr et le tmoin [FUNC.] steint.

Ce rglage revient ses valeurs par dfaut (temprament gal) lorsque vous modiez la position du slecteur de sonorit et que vous mettez lappareil hors tension.

Les sonorits Piano 1 et Piano 2 utilisent laccord tir. En comparaison avec le temprament gal, cet accord abaisse lgrement la hauteur tonale des notes basses et augmente lgrement celle des notes hautes de manire crer une rsonance plus naturelle.

Rglage de la brillance du son (Brilliance) Utilisez cette fonction pour slectionner la brillance du son.

1. Vriez que le tmoin [SONG] est teint, puis appuyez sur [FUNC.]. Le tmoin [FUNC.] sallume.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que brL apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage de brillance actuel. (Le rglage par dfaut est 02.)

3. Utilisez les touches [] ou [] pour modier le rglage.

4. Appuyez sur [FUNC.] pour valider le rglage. Le rglage est enregistr et le tmoin [FUNC.] steint.

Ce rglage est conserv mme lorsque lalimentation est coupe. Si vous appuyez sur [FUNC] aprs avoir modi le rglage, le HT-70 enregistre automatiquement le nouveau rglage dans la mmoire non volatile. Pen- dant lcriture, lafchage indique quune opration dcriture est en cours.

Ne mettez pas le HT-70 hors tension pendant lcriture. Cela risquerait dentraner la perte ou la corruption des rglages et donnes de morceaux mmoriss.

Afchage 15.0 ... 39.5 40.0 40.5 ... 65.0

Hauteur tonale (Hz) 415,0 ... 439,5 440,0 440,5 ... 465,0

Afchage 00 01 02

Rglage Temprament gal Werckmeister Kirnberger

Afchage 01 02 03

Rglage Son doux avec brillance attnue

Brillance normale

Son plus brillant

2

Changement de la sensibilit du clavier Vous pouvez changer la faon dont la dynamique du son rpond la for ce de votre jeu. Il sagit de la fonction Touch Control. Quand vous mettez lappareil sous tension, le rglage de toucher normal (02) est slectionn. 1. Maintenez la touche [FUNC.] enfonce pendant environ une seconde.

Le tmoin du commutateur commence clignot.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que tch apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage actuel de la sensibilit. (Le rglage par dfaut est 02.)

3. Utilisez les touches [] ou [] pour modier le rglage.

4. Appuyez sur [FUNC.] pour valider le rglage. Le rglage est enregistr et le tmoin [FUNC.] steint.

Le rglage revient 02 la mise hors tension.

Changement de cl (Transpose) En changeant la cl du HT-70 (en transposant) vous pouvez accompagner un autre instrument ou des voix en utilisant une cl plus facile (e.g., une qui a moins de touches noires) ou la cl dans laquelle vous avez appris le morceau. Il sagit de la fonction Transpose. Vous pouvez transposer la hauteur dans une plage de onze demi-tons.

1. Maintenez la touche [FUNC.] enfonce pendant environ une seconde. Le tmoin du commutateur commence clignot.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que trS apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage de transposant actuel. (Le rglage par dfaut est 00.)

3. Utilisez les touches [] ou [] pour modier le rglage.

4. Appuyez sur [FUNC.] pour valider le rglage. Le rglage est enregistr et le tmoin [FUNC.] steint.

Le rglage revient 00 la mise hors tension.

Pour jouer le morceau un demi-ton plus haut Vous souhaitez obtenir la hauteur tonale de C

quand vous jouez C.

Rglez la touche sur C (01 sur lafchage).

Rsultat : Lorsque vous jouez sur le clavier les notes illustres gauche, le HT-70 produit les notes illustres droite.

Le morceau est dans la cl de B mais vous souhaitez le jouer en utilisant le doigt de la cl de G

Le hauteur tonale de B est une tierce mineure (trois demi-tons) au-dessus de G. Cela signie que vous souhaitez obtenir la hauteur tonale de D

(trois

demi-tons plus haut) quand vous appuyez sur C. Rglez la touche sur D

(03 sur lafchage).

Restauration des rglages dusine Si vous avez slectionn des sonorits et chang leurs rglages, mais souhaitez restaurer les rglages dusine du HT-70, procdez de la faon suivante. Cette procdure neffacera pas les donnes de la session enregistre mais rini- tialisera tous les autres rglages leur valeur initiale. Si vous souhaitez effacer les donnes de la session enregistre, reportez-vous la section Suppression dun morceau la page 40.

Avant de continuer, assurez-vous que vous souhaitez vraiment restaurer les rglages dusine.

1. Mettez lappareil hors tension.

2. Tout en maintenant la touche [ ] enfonce, mettez lappareil sous tension. LFd apparat sur lafchage et tous les rglages reviennent leurs valeurs par dfaut.

Afchage 01 02 03

Rglage du toucher

Lger (mme un jeu lger peut produire des son forts)

Normal (le toucher dun piano typique)

Lourd (vous devez jouer for- tement pour produire des sons puissants)

Afchage -11 ... -03 -02 -01 00 01 02 03 ... 11

que C ... A A B C C D D ... B

43

4

MIDI Quest-ce que MIDI? MIDI (Musical Instrument Digital Interface) est une norme internationale pour lchange de donnes musicales entre des ordinateurs et instruments musicaux lectroniques. Vous pouvez employer le HT-70 pour reproduire dautres instruments MIDI. Dans ce cas, vos slections de sonorits, les oprations de pdale de soutien, etc., seront transmises comme donnes de contrle. Vous pouvez aussi utiliser un autre clavier ou squenceur MIDI (un dispositif de lecture automatique) pour contrler le HT-70 et son gnrateur de sons interne. En combinant plusieurs instruments MIDI vous pouvez crer des ensembles l- gants. Vous pouvez aussi sauvegarder les donnes de lenregistreur du HT-70 sur un dispositif extrieur de stockage via MIDI. Cette section dcrit les oprations lies MIDI et les fonctions du HT-70. Si vous souhaitez en savoir plus sur MIDI, veuillez consulter un des nombr eux livres dinitiation disponibles sur le sujet.

Effectuer des raccordements MIDI Des cbles MIDI disponibles dans le commerce sont utiliss pour transfrer les donnes MIDI. Raccordez ces cbles des prises MIDI du HT-70 aux prises MIDI du priphrique MIDI avec lequel vous souhaitez changer des donnes. Il y a deux types de prises MIDI.

Prise MIDI IN Elle reoit les messages MIDI. La prise MIDI IN vous permet de jouer les sons du HT-70 sur un priphrique MIDI (e.g., un clavier ou squenceur MIDI). Utilisez un cble MIDI pour r elier la prise MIDI IN du HT-70 la prise MIDI OUT de votre priphrique MIDI.

Prise MIDI OUT Elle transmet les messages MIDI. La prise MIDI OUT vous permet de contrler La prise MIDI OUT dun priph- rique MIDI en utilisant les messages MIDI transmis par le HT-70. Utilisez un cble MIDI pour relier la prise MIDI OUT du HT-70 la prise MIDI IN de votre priphrique MIDI.

Canaux MIDI Quand vous avez ni deffectuer les raccordements, rglez le HT-70 sur le mme canal MIDI du priphrique MIDI auquel vous laviez raccor d. Il y a seize canaux MIDI, numrots de 1 16.

Le rglage du canal revient C01 la mise sous tension.

1. Maintenez le commutateur [FUNC.] enfonc pendant environ une seconde. Le tmoin du commutateur commence clignoter.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que Ch apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage actuel. (Le rglage par dfaut est C01.)

3. Utilisez les touches [] ou [] pour modier le rglage.

4. Appuyez sur [FUNC.] pour valider le rglage. Le rglage est enregistr et le tmoin [FUNC.] steint.

Le HT-70 peut enregistrer les donnes MIDI provenant du canal MIDI slec- tionn.

Utilisation du HT-70 comme module sonore multitimbral Quand vous mettez le HT-70 sous tension, son gnrateur de son interne opre comme un module sonore multitimbral 16 voies, qui peut tre jou partir dun priphrique MIDI.

1. Utilisez un cble MIDI pour relier la prise MIDI IN du HT-70 la prise MIDI OUT de votre squenceur ou dispositif similaire.

2. Recevez les messages MIDI du squenceur raccord, etc.. En ce qui concerne les dtails sur la faon de transmettre les donnes du squenceur branch, reportez-vous au manuel du propritaire de lquipe- ment utilis.

Si le HT-70 reoit des messages de changement de programme avec les donnes dinterprtation, il changera la tonalit (timbre) conformment aux numros de programme entrant au fur et mesure de linterprtation. Notez que cela se pro- duit uniquement si le ltre de changement de programme est dsactiv pour le canal MIDI pertinent. Notez toutefois que le canal MIDI slectionn ( p.44) ignore les changements de programme.

Le ltrage est rinitialis la valeur OFF la mise sous tension du HT-70.

1. Maintenez le commutateur [FUNC.] enfonc pendant environ une seconde. Le tmoin du commutateur commence clignoter.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que 16t apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage actuel. (Le rglage par dfaut est activ).

3. Utilisez les touches [] ou [] pour modier le rglage.

4. Appuyez sur [FUNC.] pour valider le rglage. Le rglage est enregistr et le tmoin [FUNC.] steint.

Le slecteur de sonorit ne peut pas tre utilis pour modier les sonorits lorsque le HT-70 lit des donnes MIDI externes. Cela est toutefois possible pour le canal MIDI slectionn (p.44).

Activation/dsactivation de Local Vous devriez dsactiver le rglage Local du HT-70 si vous souhaitez que le cla- vier du piano acoustique auquel le HT-70 est reli contrle seulement un module sonore externe MIDI et non pas le gnrateur de son du HT-70, ou souhaitez vi- ter la duplication des notes quand vous raccordez le HT-70 un squenceur qui renvoie (retransmet) les donnes entrantes au HT-70. Normalement, vous laisserez le rglage Local du HT-70 activ pour que ce der- nier produise des sons quand vous jouez sur le clavier.

Immdiatement aprs la mise sous tension, le rglage Local sera automati- quement activ. on.

1. Maintenez le commutateur [FUNC.] enfonc pendant environ une seconde. Le tmoin du commutateur commence clignoter.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que L.ct apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage actuel. (Le rglage par dfaut est activ.)

3. Utilisez les touches [] ou [] pour modier le rglage.

4. Appuyez sur [FUNC.] pour valider le rglage. Le rglage est enregistr et le tmoin [FUNC.] steint.

Afchage C01 ... C16

canal 1 ... 16

Afchage on oFF

multitimbral activ dsactiv

Afchage on oFF

Local activ dsactiv

4

Changements de programme Ces messages peuvent tre mis par le HT-70 pour slectionner les numros de programme sur un priphrique MIDI ou reus depuis un priphrique MIDI pour changer les numros de programme sur le HT-70.

Transmission des changements de programme Les numros de programme sur priphrique MIDI peuvent tre changs par- tir du HT-70.

Lorsque vous modiez le rglage du slecteur de tonalit, le HT-70 envoie le numro de changement de programme correspondant. Le tableau de la sec- tion suivante indique les correspondances.

Rception des changements de programme Si le HT-70 reoit un numro de changement de programme depuis un priph- rique, son gnrateur de son multitimbral changera les pr ogrammes comme indiqu dans le tableau ci-dessous. Notez toutefois que le canal MIDI slectionn (p.44) ignore les changements de programme.

Le HT-70 modie les sonorits (timbres) conformment aux numros de change- ment de programme reus lists dans le tableau ci-dessous. Si les priphriques MIDI distants envoient au HT-70 un numro de changement de programme qui nest pas inclus dans la liste ci-dessous, le HT-70 arrtera de gnrer du son MIDI.

Filtre de changement de programme Rglez le ltre sur ON pour dsactiver lenvoi et la rception dinformations de changement de programme. Rglez le ltre sur OFF pour activer la transmission de ces informations.

A la mise sous tension, le ltrage est rinitialis la valeur OFF pour tous les canaux MIDI.

1. Maintenez le commutateur [FUNC.] enfonc pendant environ une seconde. Le tmoin du commutateur commence clignoter.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que PC apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage actuel. (Le rglage par dfaut est off.)

3. Utilisez les touches [] ou [] pour modier le rglage.

4. Appuyez sur [FUNC.] pour valider le rglage. Le rglage est enregistr et le tmoin [FUNC.] steint.

Filtre de changement de contrle Les messages de changement de contrle envoient des informations qui sont uti- lises pour dnir le fonctionnement des contrles, tels que la pdale de rso- nance. Les priphriques MIDI externes utilisent ces messages pour contrler le fonctionnement du HT-70, et le HT-70 les utilise pour contrler le fonctionne- ment des priphriques MIDI externes. Rglez le ltre sur OFF pour activer lenvoi et la rception de message de chan- gement de contrle. Rglez le ltre sur ON pour dsactiver la transmission de ces informations.

A la mise sous tension, le ltrage est rinitialis la valeur OFF pour tous les canaux MIDI.

1. Maintenez le commutateur [FUNC.] enfonc pendant environ une seconde. Le tmoin du commutateur commence clignoter.

2. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que CC apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage actuel. (Le rglage par dfaut est off).

3. Utilisez les touches [] ou [] pour modier le rglage.

4. Appuyez sur [FUNC.] pour valider le rglage. Le rglage est enregistr et le tmoin [FUNC.] steint.

Simple Bank# PC# Son

00 00 PIANO1

01 00 PIANO2

00 04 E.PIANO1

00 05 E.PIANO2

00 06 HARPSI.

00 19 P.ORGAN

00 16 E.ORGAN

00 48 STRINGS

Afchage on oFF

ltre on off

Afchage on oFF

ltre on off

45

4

USB Utilisation de MIDI via une con- nexion USB Le HT-70 permet dtablir des communications MIDI avec un ordinateur direc- tement via une connexion USB. Il nest ainsi plus ncessaire dutiliser un cble MIDI ni un priphrique dinterface MIDI spar pour tablir la connexion. Une fois la connexion tablie, vous pouvez utiliser le HT-70 comme gnrateur de son MIDI ou comme clavier MIDI, par exemple.

Connexion un ordinateur Dans la mesure du possible, utilisez le pilote KORG USB-MIDI lors du raccorde- ment un ordinateur via une connexion USB. Plus particulirement, vous devrez utiliser le pilote pour tout raccordement un ordinateur compatible.

Les environnements informatiques prenant en charge le pilote KORG USB-MIDI sont les suivants. Windows:

Ordinateur: Il doit comporter un port USB embarqu et fonctionner sous Microsoft Win- dows XP ou Microsoft Windows Vista.

Systme dexploitation: Microsoft Windows XP / Vista (Remarque : le pilote Korg USB-MIDI pour Windows Edition x64 est dispo- nible en version beta uniquement.)

Macintosh: Ordinateur: Apple Macintosh avec un port USB embarqu fonctionnant sous Mac OS X.

Systme dexploitation: Mac OS X version 10.3 ou suprieure

Le respect des congurations ci-dessus ne garantit pas le bon fonctionne- ment de votre ordinateur avec le HT-70. Certains ordinateurs peuvent ne pas tre compatibles mme sils rpondent ces exigences.

Notez bien ceci avant utilisation Les droits dauteur du logiciel fourni avec ce produit sont la proprit de Korg Inc. Un accord de licence logicielle est fourni sparment. Lisez la licence avant dinstaller le logiciel. Le fait dinstaller le logiciel indique que vous acceptez les termes du contrat de licence.

Windows XP et Vista: Installation du pilote KORG USB-MIDI Ne raccordez pas le HT-70 lordinateur laide du cble USB avant davoir ins- tall le pilote KORG USB-MIDI. Procdez comme suit.

1. Insrez le CD-ROM fourni dans le lecteur CD-ROM de votre ordinateur. La plupart du temps, lassistant dinstallation de lapplication KORG Digital Piano se lance automatiquement lorsque vous insrez le CD-ROM. Si la con- guration de votre ordinateur a dsactiv lexcution automatique, lancez le programme en navigant sur le CR-ROM et en double-cliquant sur le chier Korg-Setup.exe.

2. Suivez les instructions lcran.

Le programme dinstallation installe galement le KORG MIDI Data Filer. Le HT-70 nutilise pas le Data Filer.

3. Mettez le HT-70 sous tension, puis raccordez-le lordinateur laide dun cble USB. Lordinateur installe alors automatiquement le pilote USB-MIDI standard pour Windows. Vous devez alors procder linstallation du pilote KORG USB-MIDI pour le port USB que vous utilisez.

Installation du pilote KORG USB-MIDI pour Windows 1. Installez le pilote KORG USB-MIDI comme dcrit ci-dessus.

2. Redmarrez lordinateur, mettez le HT-70 sous tension, puis raccordez le HT- 70 lordinateur laide dun cble USB.

Le pilote KORG USB-MIDI doit tre install sparment pour chaque port USB avec lequel il va tre utilis. Si vous dcidez ultrieurement de raccorder le HT-70 un autre port USB, vous devrez rpter cette procdure pour installer le pilote sur ce port galement.

3. Slectionnez la commande suivante dans la barre des tches pour ouvr ir les instructions dinstallation : Dmarrer Programmes KORG KORG USB-MIDI Driver Tools Installation Manual.

4. Suivez les instructions dinstallation lcran pour installer le pilote.

Ports du pilote Port Clavier: Utilis par lapplication informatique pour recevoir les messages MIDI (donnes du clavier et de contrle) partir du HT-70. Port Son: Utilis par lapplication informatique pour envoyer les messages MIDI qui engendrent la production de son par le gnrateur de son interne du HT-70.

Mac OS X : Installation du pilote KORG USB-MIDI Dans la mesure du possible, utilisez le pilote KORG USB-MIDI lors du rac- cordement un ordinateur via une connexion USB. Plus particulirement, vous devrez utiliser le pilote pour tout raccordement un ordinateur com- patible.

Installation du pilote KORG USB-MIDI 1. Insrez le CD-ROM fourni dans le lecteur CD-ROM de votre ordinateur.

2. Ouvrez le dossier KORG USB-MIDI Driver du CD-ROM, puis double-cli- quez sur KORG USB-MIDI Driver.pkg pour lancer le programme dinstalla- tion. Suivez ensuite les instructions lcran.

Ports du pilote Port Clavier: Utilis par lapplication informatique pour recevoir les messages MIDI (don- nes du clavier et de contrle) partir du HT-70. Port Son: Utilis par lapplication informatique pour envoyer les messages MIDI qui engendrent la production de son par le gnrateur de son interne du HT-70.

6

Mode USB Le HT-70 prend en charge le transfert de donnes entre sa mmoire interne et un ordinateur externe. Une connexion USB constitue la mthode la plus ef cace deffectuer de tels transferts. Cette fonctionnalit est prise en char ge par Win- dows ME, Windows 2000 et toutes les versions ultrieures de Windows, ainsi que par Mac OS version 9.0.4 et suprieure.

Avant de passer en mode USB pour transfrer des donnes depuis ou vers le HT-70, vriez que toutes les applications MIDI sur lordinateur sont fermes. Si une application MIDI est en cours dexcution pendant le transfert USB, les donnes du HT-70 risquent dtre corrompues.

Le HT-70 redmarre automatiquement lorsque vous quittez le mode USB. (en dsactivant le mode sur le HT-70, dbranchant le cble USB, interrom- pant la connexion sur lordinateur, etc.) Toute donne et tout rglage non sauvegards sont donc perdus. Veillez bien sauvegarder les donnes et rglages avant de passer en mode USB.

La connexion USB ne peut pas tre utilise pour les communications MIDI tant que le mode USB est utilis pour le transfert de donnes.

1. Raccordez le HT-70 et lordinateur via un cble USB.

2. Maintenez le commutateur [FUNC.] enfonc pendant environ une seconde. Le tmoin [FUNC.] commence clignoter.

3. Appuyez plusieurs fois sur [DISPLAY] jusqu ce que USb apparaisse dans lafchage. Lorsque vous relchez le commutateur, lafchage indique le rglage actuel. (A la mise sous tension, le mode USB est dsactiv.)

Une fois le mode USB activ, la plupart des oprations sont indisponi- bles. Seules les oprations suivantes restent disponibles : dsactivation du mode USB, activation/dsactivation de la rverbration, activa- tion/dsactivation du mtronome et utilisation du clavier pour jouer des notes.

4. Utilisez les touches [] ou [] pour modier le rglage.

Le HT-70 redmarre automatiquement lorsque vous dsactivez le mode USB.

Si vous quittez le mode USB pendant le transfert de donnes USB (en dsactivant le mode USB sur le HT-70, en dconnectant le cble USB, etc.), cela risque de provoquer une corruption des donnes sur le HT- 70 et dendommager lordinateur.

Ne mettez pas le HT-70 hors tension tant que le mode USB est activ. Cela risquerait de provoquer la corruption des donnes du HT-70 et dendommager lordinateur.

5. Une fois le mode USB activ, vous pouvez utiliser le HT-70 comme nimporte quel priphrique USB externe. Vous pouvez dplacer des chiers sur et vers le HT-70 ou lutiliser pour sauvegarder et restaurer vos donnes. Les donnes du HT-70 sont stockes dans des sous-dossiers sous le dossier KORG USER. Le nom des chiers sous ces dossiers peut comporter 128 caractres maximum.

6. Une fois le transfert de donnes termin, retirez ou supprimez le pilote USB du bureau de votre ordinateur. Pour plus dinformations, reportez-vous au mode demploi de lordinateur. Sous Windows XP : lorsque vous retirez ou supprimez le pilote USB, le HT- 70 revient automatiquement son cran initial (mise sous tension). (Sous Windows Vista, aprs avoir retir le pilote USB de lordinateur, vous devez appuyer sur le commutateur sur le HT-70 pour revenir lcran initial.) Sous Mac OS : lorsque vous placez KORG SSD dans la Corbeille (ou que vous supprimez KORG SSD), le HT-70 revient automatiquement son cran initial (mise sous tension).

Lecture de chiers MIDI Le HT-70 peut reconnatre et lire des morceaux stocks dans le dossier User- Song, si ces morceaux sont stocks au format MIDI standard et que le nom des chiers comporte un U suivi de deux chiffres (01 99) et de lextension de chier .mid.

Examples: U07.mid, U34.mid

Le HT-70 risque de ne pas lire correctement les chiers MIDI standard qui utilisent une signature temporelle que le HT-70 lui-mme ne peut pas d- nir.

Afchage on oFF

Mode USB ON (Stockage de masse) OFF (USB MIDI)

Dossier Contenu

GLOBAL Rglages gnraux (communs)

PRESET Prrglages sonores

UserSong Morceaux enregistrs sur le HT-70 et morceaux crs par des squenceurs externes. Tous les morceaux enregistrs au format MIDI standard (extension de chier .MID) peu- vent tre copis dans ce dossier.

47

4

Appendice Guide de dpannage

Lappareil ne peut pas tre mis sous tension Est-ce que la prise DC de ladaptateur secteur est bien raccorde la

prise DC12V du HT-70 ?

Est-ce que le cble dalimentation de ladaptateur secteur est bien rac- cord une prise secteur dont la tension est approprie ?

Est-ce que lappareil a bien t allum ? (p.32)

Si lappareil ne peut toujours pas tre mis sous tension, d.branchez le cble dalimentation de ladaptateur secteur, et contactez un centre de service aprs-vente.

Aucun son Est-ce que la commande [VOLUME] du HT-70 est tourne compltement

gauche (juste avant la position 0) ? (p.32)

Est-ce que le passage choisi a t congur pour tre reproduit ? (p.41)

Est-ce que donnes de jeu ont t enregistres pour le passage choisi ? (p.39 )

Est-ce que le son du passage choisi a t coup ? (p.41)

Assurez-vous que Local est rgl sur ON (p.44).

Est-ce que lafchage comporte une indication derreur (E01) ? Si cest le cas, une erreur sest produite au niveau du cble qui raccorde le piano lunit HT-70. Contactez un technicien agr ou votre reven- deur pour la rparation. Lafchage derreur (E01) disparat si vous appuyez sur la touche [] ou [].

Est-ce que lerreur E04 apparat sur lafchage ? Si cest le cas, contactez votre revendeur ou un technicien quali pour obtenir de laide. Pour supprimer lafchage derreur (E04), appuyez sur [] ou [].

Si lafchage multiple indique E02 Les donnes dinstallation pour lappareil ont t perdues, aussi les don-

nes par dfaut ont t charges. Vous pouvez continuer utiliser le HT-70, mais le volume, la hauteur tonale et leffet de la pdale peuvent tre incorrects. Veuillez contacter un installateur agr ou votre concessionnaire pour les rparations et le rglage. Lafchage derreur (E02) disparat si vous appuyez sur la touche [] ou [].

Les notes sont coupes Le HT-70 est conu pour donner la priorit aux notes joues le plus

rcemment. Si vous dpassez la polyphonie maximale, les notes joues au pralable seront coupes. La polyphonie maximale pour la sonorit E.Piano 1 est de 80 notes. Cependant, comme les autres sons emploient deux fois plus de donnes pour chaque note, leur polyphonie maximale est de 40 notes. Si vous utilisez la pdale forte ou reproduisez des don- nes enregistres, noubliez pas de prendre en compte la polyphonie maximale et choisissez la sonorit appropri. La hauteur tonale ou tona- lit du piano semble incorrecte dans certaines zones du clavier.

La hauteur tonale ou tonalit du piano semble incor- recte dans certaines zones du clavier

Les sonorits de piano du HT-70 reproduisent aussi dlement que pos- sible celles dun piano rel. Cela signie que dans certaines rgions du clavier, il est possible que le son semble plus fort, ou que la tonalit ou hauteur tonale semble incorrecte. Cest un phnomne normal.

Une touche spcique ne produit pas de son, ou le son produit est trop fort ou trop faible

Laction de la pdale est insufsante ou trop forte

Le hauteur tonale est diffrente de celle dun piano acoustique

Est-ce que lerreur E03 apparat sur lafchage ? Si cest le cas, le HT-70 nest pas talonn. Contactez votre revendeur ou un technicien quali pour obtenir de laide.

Si une des touches est muette, ou est trop forte ou trop faible, il y a pro- bablement un problme au niveau de ltalonnage. Contactez votr e revendeur ou un technicien quali pour obtenir de laide.

Le dispositif de sourdine peut causer les problmes ci-dessus sil nest pas rgulirement entretenu et rgl par un technicien agr. Il est recommand de faire accorder et rgler le piano tous les ans.

Le clavier ne produit aucun son lorsquil est utilis en tant que piano. (si linstrument est quip dun module de sourdine automatique)

Le tmoin de la barre de sourdine en dessous du piano est-il allum ? (p.31)

La barre de sourdine lectrique peut tre bloque. Une solution tempo- raire consiste dbloquer la barre de force laide des crochets de dblo- cage fournis avec linstrument.

Contactez ensuite votre revendeur ou un agent de maintenance quali pour obtenir des conseils.

Impossible denregistrer. Est-ce quil a assez despace libre sur votre enregistreur ? (p.40, p.49)

Quand je renregistre partir du milieu dun enregistre- ment, le tempo ou la mesure sont diffrents pour le pas- sage enregistr.

Quand vous renregistrez, est-ce que vous avez rgl le tempo et la mesure pour quils soient identiques ceux de lenregistrement prcdent ? Lors de lenregistrement sur des donnes de morceaux existantes, le HT- 70 peut modier le tempo mais pas la signature temporelle. Lors de lajout de nouvelles mesures des morceaux existants, le HT-70 peut toutefois modier la mesure et le tempo (p.40).

Impossible de reproduire les passages 1 et 2 avec un tempo ou une mesure indpendants.

Sur le HT-70, les passages 1 et 2 ont les mmes tempos et mesures. La mesure du passage enregistr en premier sera utilis pour la lecture (p.40).

Mon priphrique ne rpond pas aux donnes MIDI transmises.

Assurez-vous que le cble MIDI est branch correctement(p.44).

Assurez-vous que le HT-70 transmet les donnes MIDI sur le mme canal que celui sur lequel votre priphrique les reoit (p.44).

Barre de sourdine

Position de dblocage

Position de sourdine

Crochet de dblocage

8

49

Impossible dinstaller le pilote USB-MIDI pour Win- dows (quand vous utilisez Windows)

Assurez-vous que le cble USB est branch correctement (p.44).

Assurez-vous que le CD-ROM est correctement insr dans votre lecteur de CD.

Est-ce que la lentille de votre lecteur de CD est sale ? Utilisez un produit de nettoyage de lentille disponible dans le commerce pour nettoyer la lentille de votre lecteur de CD.

Est-ce que vous essayez deffectuer linstallation partir dun lecteur de CD en rseau ? Vous ne pouvez pas installer le pilote partir dun lecteur de CD via un rseau.

Assurez-vous que lUSB est disponible sur votre ordinateur. Sous Windows, allez [Panneau de conguration] [Systme] onglet [Matriel] [Gestionnaire de Priphriques] pour vrier la prsence du contrleur de bus USB et de lUSB Root Hub.

Est-ce que le HT-70 a t dtect comme un priphrique inconnu ? Sous Windows, allez [Panneau de conguration] [Systme] onglet [Matriel] [Gestionnaire de Priphriques] pour vrier cette condi- tion. Si le HT-70 na pas t correctement dtect, il sera signal sous la forme Autre priphrique USB ou Priphrique inconnu. Rebran- chez le cble USB, et si le HT-70 est encore dtect comme Priphrique inconnu, effacez le Priphrique inconnu et rinstallez le Pilote (p.46).

Le logiciel ne rpond pas Assurez-vous que le cble USB est branch correctement (p.47).

Est-ce que vous avez install le pilote?

Assurez-vous que lordinateur sur lequel vous avez branch le HT-70 la reconnu correctement. Sous Windows, ouvrez dans le panneau de conguration [Sons et pri- phriques audio] [Matriel] pour vrier cela. Sous Mac OS X, ouvrez le dossier Applications, puis le dossier Utilitaires et cliquez sur Conguration audio et MIDI. Cliquez ensuite sur Pri- phriques MIDI, et vriez si le HT-70 gure dans la liste des priphri- ques disponibles. Suivant lordinateur utilis, il est possible que le HT-70 ne puisse pas tre reconnu via une liaison USB.

Vriez la conguration du HT-70 et celle des ports USB MIDI (p.46).

Il est possible que le priphrique ou le logiciel ne supportent pas les fonctionnalits du HT-70. Reportez-vous au mode demploi de votre logiciel ou du priphrique que vous avez branch.

Utilisation du HT-70 sans assourdir le piano acoustique La conception du HT-70 vous permet de couper le son du piano acoustique, an que vous puissiez jouer et vous entraner en utilisant un casque. Mais vous pou- vez aussi utiliser une partie des fonctionnalits du HT-70 sans couper le son du piano acoustique.

Jouer du piano acoustique en coutant le mtronome ou un morceau de piano. Si vous ne voulez pas vous couter jouer avec les haut-parleurs, rgler Local sur OFF.(voir page 44 Activation/dsactivation de Local)

Voici plusieurs possibilits :

Jouer du piano acoustique en superposant (mode Layer) les sons du HT-70.

Les messages MIDI du HT-70 tant transmis mme si vous ne coupez pas le son du piano acoustique, vous pourrez transmettre les messages MIDI tout en jouant du piano acoustique si des priphriques MIDI sont raccords au HT-70.

Sur le modle avec haut-parleurs, le son du HT-70 peut tre transmis par ces derniers. Cependant, mme sur le modle sans haut-parleurs, vous pouvez relier des haut-parleurs amplis disponibles dans le commerce la prise de sortie de ligne et utiliser votre instrument de la mme faon.

Messages derreur La plupart des messages derreur restent sur lafchage pendant quelques secondes uniquement. Si un message derreur (tel que E05 ou E06) reste sur lafchage pendant une priode prolonge, vous pouvez le supprimer en appuyant sur [] ou [].

E05 Lenregistrement a t automatiquement interrompu, car vous avez essay denregistrer au-del de la 999me mesure du morceau. Les 999 mesures enregistres restent dans la mmoire.

E06 Lenregistrement a t automatiquement interrompu, car vous avez essay denregistrer plus de 45.000 notes dans un morceau. Les 45.000 notes enre- gistres restent dans la mmoire.

E07 La mmoire de morceaux utilisateur est sature. Pour enregistrer davantage de donnes, vous devez librer de lespace en supprimant les donnes de morceaux inutiles. Si ncessaire, sauvegardez les chiers des morceaux important sur un ordinateur ou tout autre priphrique externe avant de supprimer les donnes.

E08 Impossible dexcuter lenregistrement, car le morceau utilisateur na pas pu tre charg. Cette erreur se produit aprs lerreur E0b si vous essayez de pro- cder un enregistrement.

E09 La tentative de sauvegarder les paramtres ou de modier les donnes dun morceau a chou. Le HT-70 a probablement besoin de rparations. Contac- tez un technicien agr ou votre revendeur pour obtenir des conseils.

E0A Lcriture du morceau a t dsactive sur lordinateur. Pour modier le morceau sur le HT-70, changez son nom et enregistrez-le comme un nouveau morceau.

E0b Le chier du morceau est trop gros ou il est incompatible. Si vous essayez de procder lenregistrement, lafchage indique lerreur E08.

E00...EFF Erreur du capteur. Contactez un technicien agr ou votre revendeur pour obtenir des conseils.

Spcications

* Les spcications et la nition sont sujettes modication sans pravis pour amlioration.

Son trait avec systme INFINITY

Sonorits Huit timbres : Piano 1, Piano 2, Electric piano 1, Electric piano 2, Harpsichord, Pipe organ, Electric organ, Strings

Gnrateur de sonorits chantillonnage strophonique

Polyphonie maximale 80 notes

Effects Reverb (trois niveaux), Brillance (trois niveaux)

Enregistreur Deux pistes, 45.000 notesTempo/metronome, Record, Play/Pause, Stop, Part 1, Part 2

Mode de clavier Normal

Tempraments Trois types (temprament gal, Kirnberger, Werckmeister)

Rglage du touche Trois niveaux (lger, normal, lourd)

Commandes Bouton [VOLUME], slecteur de sonor it, tou- ches [SONG], [REVERB], [DISPLAY], [FUNC.], [], [], [ ], [], [], [ ], [PART 1], [PART 2]

Pdales *Soutien, Sostenuto, *Sourdine *Fonction demi-pdale supporte

Prises Casque x 2, LINE OUT (stro), MIDI (IN, OUT), USB

Alimentation DC12V (adaptateur secteur inclus)

Dimensions (L x P x H) 271 x 180 x 63 (mm) (module sonore seulement)

Weight 1.4 Kg (module sonore seulement)

Accessoires fournis Adaptateur secteur, casque, CD-ROM, haut- parleurs externes (seulement pour modle avec haut-parleurs)

50

Vorsichtsmanahmen Aufstellungsort Vermeiden Sie das Aufstellen des Gerts an Orten, an denen

es direkter Sonneneinstrahlung ausgesetzt ist; hohe Feuchtigkeit oder Extremtemperaturen

auftreten knnen; Staub oder Schmutz in groen Mengen vorhanden

sind; das Gert Erschtterungen ausgesetzt sein kann. in der Nhe eines Magnetfeldes.

Stromversorgung Schlieen Sie das beiliegende Netzteil nur an eine geeignete Steckdose an. Verbinden Sie es niemals mit einer Steckdose einer anderen Spannung.

Streinsse auf andere Elektrogerte Dieser kann bei in der Nhe aufgestellten Rund- funkempfngern oder Fernsehger ten Emp- fangsstrungen hervorrufen. Betreiben Sie solche Gerte nur in einem geeigneten Abstand von diesem Erzeugnis.

Bedienung Vermeiden Sie bei der Bedienung von Schaltern und Reglern unangemessenen Kraftaufwand.

Reinigung Bei auftretender Verschmutzung knnen Sie das Gehuse mit einem trockenen, sauberen Tuch abwis- chen. Verwenden Sie keinerlei Flssigreiniger wie beispielsweise Reinigungsbenzin, Verdnnungs- oder Splmittel. Verwenden Sie niemals brennbare Reini- ger.

Bedienungsanleitung Bewahren Sie diese Bedienungsanleitung gut auf, falls Sie sie spter noch einmal bentigen.

Flssigkeiten und Fremdkrper Stellen Sie niemals Behltnisse mit Flssigkeiten in der Nhe des Gerts auf. Wenn Flssigkeit in das Gert gelangt, knnen Beschdigung des Gerts, Feuer oder ein elek-trischer Schlag die Folge sein.

Beachten Sie, da keinerlei Fremdkrper in das Gert gelangen. Sollte ein Fremdkrper in das Gert gelangt sein, so trennen Sie es sofort vom Netz. Kontaktieren Sie einen qualizierten Techniker oder Fachhndler.

Hinweis zur Entsorgung (Nur EU) Wenn Sie das Symbol mit der durchgekreuzten Mll- tonne auf Ihrem Produkt, der dazugehrigen Bedie- nungsanleitung, der Batterie oder dem Batteriefach sehen, mssen Sie das Produkt in der vorgeschrie- benen Art und Weise entsorgen. Dies bedeutet, dass dieses Produkt mit elektrischen und elektronischen Komponenten nicht mit dem normalen Hausmll entsorgt werden darf. Fr Produkte dieser Art existiert

ein separates, gesetzlich festgelegtes Entsorgungssystem. Gebrauchte elektrische und elektronische Gerte mssen sepa- rat entsorgt werden, um ein umweltgerechtes Recycling sicher- zustellen. Diese Produkte mssen bei benannten Sammelstellen abgegeben werden. Die Entsorgung ist fr den Endverbraucher kostenfrei! Bitte erkundigen sie sich bei ihrer zustndigen Behrde, wo sie diese Produkte zur fachgerechten Entsorgung abgeben knnen. Falls ihr Produkt mit Batterien oder Akkumu- latoren ausgerstet ist, mssen sie diese vor Abgabe des Produk- tes entfernen und separat entsorgen (siehe oben). Die Abgabe dieses Produktes bei einer zustndigen Stelle hilft ihnen, dass das Produkt umweltgerecht entsorgt wird. Damit leisten sie per- snlich einen nicht unerheblichen Beitrag zum Schutz der Umwelt und der menschlichen Gesundheit vor mglichen nega- tiven Effekten durch unsachgeme Entsorgung von Mll. Batte- rien oder Akkus, die Schadstoffe enthalten, sind auch mit dem Symbol einer durchgekreuzten Mlltonne gekennzeichnet. In der Nhe zum Mlltonnensymbol bendet sich die chemische Bezeichnung des Schadstoffes. Cd oder NiCd steht fr Cadmium, Pb fr Blei und Hg fr Quecksilber.

WICHTIGER HINWEIS FR KUNDEN Dieses Produkt wurde unter strenger Beachtung von Spezika- tionen und Spannungsanforderungen hergestellt, die im Bestim- mungsland gelten. Wenn Sie dieses Produkt ber das Internet, per Postversand und/oder mit telefonischer Bestellung gekauft haben, mssen Sie besttigen, dass dieses Produkt fr Ihr Wohngebiet ausgelegt ist. WARNUNG: Verwendung dieses Produkts in einem anderen Land als dem, fr das es bestimmt ist, verwendet wird, kann gefhrlich sein und die Garantie des Herstellers oder Importeurs hinfllig lassen werden. Bitte bewahren Sie diese Quittung als Kaufbeleg auf, da andernfalls das Produkt von der Garantie des Herstellers oder Importeurs ausgeschlossen werden kann.

* Tous les noms de produits et de socits sont des marques commerciales ou dposes de leur dtenteur respectif.

51

Inhalt

Einleitung......................................................52 Hauptfunktionen....................................................... 52

Teile und Funktionen ...................................53 Bedienfeld................................................................ 53

Rckseite ................................................................. 54

Vorbereitung zum Spielen und Demo-Song .........................55 Bevor Sie mit dem Spielen beginnen....................... 55

Netzanschluss ............................................................. 55

Stummschalten des akustischen Klavierklangs ..........55

Kopfhrer..................................................................... 55

Wenn das Bedienfeld schlecht lesbar ist.....................56

Gert einschalten ........................................................ 56

Einschalten des Gerts ...............................................56

Anhren von Sounddemos ...................................... 56 Hren der Sound-Demos ............................................56

Spielen des HT-70 ........................................58 Auswhlen eines Sounds ........................................ 58

Verwenden der Pedale ............................................ 58

Hinzufgen von Nachhall zum Sound (Reverb)....... 59

Zusammen mit dem Metronom spielen ................... 60 Zum Einschalten des Metronoms................................60

ndern der Metronomeinstellungen ............................60

Weitere Funktionen.................................................. 62

Aufnehmen und Wiedergeben Ihres Spiels .......................63 Aufnehmen Ihres Spiels........................................... 63

Schnellaufnahme (Aufnahme eines neuen Songs) ............................63

Aufnahme einer Darbietung.....................................63

Speichern eines aufgenommenen Songs................64

Lschen eines Songs ..............................................64

Lschen eines Parts ................................................ 64

So zeigen Sie an, wie viele Daten noch aufgenommen werden knnen ..........64

Abspielen von Songs ............................................... 65 Auswahl eines Songs ..............................................65

Unterbrechen der Songwiedergabe.........................65

Fortsetzen der Songwiedergabe .............................65

ndern des Tempos eines abgespielten Songs ......65

Navigation zu einer anderen Position (Takt) ...........65

So wiederholen Sie die Wiedergabe eines bestimmten Songabschnitts (AB Repeat) ...........65

Weitere Funktionen......................................66 Einstellen der Tonhhe............................................ 66

Whlen einer Stimmung .......................................... 66

Einstellen der Helligkeit des Sounds (Brillanz) ........ 66

Anpassen der Tastaturempfindlichkeit..................... 67

Andern der Tonart (Transponieren) ......................... 67 Um den Song einen Halbton hher zu spielen ....... 67

Der Song ist in der Tonart Bb, aber sie wollen ihn mit Fingering in der Tonart G spielen .. 67

Zurckstellen auf werkseitige Einstellungen............ 67

MIDI ............................................................... 68 Was bedeutet MIDI? ............................................... 68

Herstellen von MIDI-Verbindungen......................... 68

MIDI-Kanle............................................................ 68

Verwendung des HT-70 als multitimbrales Soundmodul.......................... 68

Lokales Ein-/Aus-Schalten...................................... 68

Programmnderungen............................................ 69

USB ............................................................... 70 Einsatz von MIDI ber eine USB-Verbindung......... 70

USB-Modus ............................................................ 71

Anhang.......................................................... 72 Strungssuche........................................................ 72

Verwendung des HT-70 ohne Stummschaltung des angeschlossenen Klaviers.......................... 73

Fehlermeldungen.................................................... 73

Technische Daten................................................... 73

Funktionsliste........................................................... 74 Metronome Functions ................................................ 74

General Functions #1 ................................................ 74

General Functions #2 ................................................ 74

General Functions #3 ................................................ 74

MIDI implementation chart....................................... 75

Konventionen in dieser Bedienungsanleitung Schalter

Schalter am HT-70 sind in rechteckigen Klammern [ ] angegeben.

(p.) : Verweist auf eine andere Seite.

: Verweist auf eine Funktion fr das Modell mit Lautsprechern.

: Verweist auf eine Vorsichtsmaregeln bei der Verwendung des HT-70.

: Verweist auf einen Ratschlag bei der Verwen- dung des HT-70.

5

Einleitung

Hauptfunktionen Umfangreiche Palette von Klngen (S.58)

Whlen Sie unter acht hochwertigen Klngen nur von Korg, einschlielich eines Konzertgels. Stereosampling wird verwendet und erlaubt ein angenehmes Raumgefhl neben dem reichen Aus- druck eines Konzertgels.

Zehn Sounddemos (S.56) Zehn integrierte Demosongs stellen die unverkennbaren Qualitten von jedem Sound vor.

Effektfunktionen (S.59, S.66) Hall und Brillanzeffekte sind inbegriffen. Der Hall kann fr jede Stimme auf eine von drei Stufen eingestellt werden. Mit den Brillanzeinstellungen regeln Sie die Klanghelligkeit.

Pedaleffekte (S.58) Die internen Sounds des HT-70 knnen mit den Klavierpedalen beeinusst werden.

Metronomfunktion (S.60) Mit dem integrierten Metronom knnen Sie die Taktart, das Tempo, die Lautstrke und den Klang beliebig festlegen. Betonungen lassen sich mit einem Glocken- oder Digitalton hervorheben.

Touch-Control-Funktion (S.67) Das dynamische Ansprechen der Tastatur ist einer der wichtigsten Aspekte eines Klaviers, und das HT-70 erlaubt es Ihnen, zwischen drei verschiedenen Typen dynamischen Ansprechens zu whlen.

Einstellbare Tonhhe (S.66, S.67) Mithilfe der integrierten Tonhhenregelung knnen Sie die Tonhhe feineinstellen. Mit der Transpo- nierfunktion knnen Sie die Tonart, in der ein Stck gespielt wird, an die Tonart eines anderen Instruments oder Musikstcks anpassen.

Stimmung (S.66) Neben der normalen gleichschwebenden Stimmung knnen Sie zwei klassische Stimmungen (Wer- ckmeister und Kirnberger) fr historisch akkurate Vorfhrungen whlen.

Recorderfunktion (S.63) Der eingebaute Recorder des HT-70 erlaubt es, Ihr eigenes Spiel aufzunehmen und wiederzugeben.

Anschlsse (S.54, S.68, S.70) Die Anschlsse LINE OUT, MIDI und USB sind vorhanden und erlauben es Ihnen, das HT-70 an Audiogerte, andere MIDI-Gerte oder einen Computer anzuschlieen.

2

Teile und Funktionen

Bedienfeld

1. Kopfhrerbuchsen Sie knnen Stereokopfhrer (1/4-Zoll-Klinke) an diese Buchsen anschlieen. Zwei Stereo-Kopfhrer knnen gleichzeitig angeschlossen werden.

Wenn Sie das Modell mit Lautsprechern verwenden und die mitgelieferten Lautsprecher angeschlossen haben, kommt kein Ton von den mitgelieferten Lautsprechern, wenn Sie Kopfhrer angeschlossen haben.

2. [POWER]-Schalter Mit diesem Schalter wechseln Sie zwischen der Position ON (Multidisplay beleuchtet) und OFF (Standby).

Im Standbymodus wird das Instrument weiterhin mit Strom versorgt. Soll die Stromzufuhr vollstndig unterbrochen werden, ziehen Sie das Netzkabel des Wechselstromnetzteils aus der Steckdose.

3. [VOLUME]-Knopf Steuert die Lautstrke des Signals, das von den Kopfhrern und Line-Out-Buchsen ausgegeben wird (S.56).

Bei Modellen mit Lautsprechern steuert er auch die Lautstrke der Lautsprecher.

4. Sound-Wahlschalter Verwenden Sie diesen zum Whlen von Sounds (S.58). Sie knnen zwischen acht Sounds whlen: PIANO 1, 2, E.PIANO (elektrisches Klavier) 1, 2, HARPSI. (Cembalo), P.ORGAN (Pfeifenorgel), E.ORGAN (elektrische Orgel) und STRINGS (Streicher).

5. [SONG] switch and LED Use this switch to select a song to be played or recorded. Press this switch together with the [REVERB] switch to play one of the built-in sound demos (S.56).

6. [DISPLAY]-Taste und LEDs ndern den Inhalt des Multidisplays. Die leucht- ende LED signalisiert den aktuellen Inhalt. Ist das Instrument auf den Funktionsmodus gest- ellt, ndern Sie mit dieser Taste den Wert einer Ein- stellung (S.74).

7. TEMPO-LED Blinkt im Rhythmus mit dem Song whrend der Wiedergabe und Aufnahme.

8. Recorder Mit diesen Tasten knnen Sie die Wiedergabe oder Aufnahme starten, unterbrechen, fortsetzen und beenden (S.63). Blinkt die [ ]-Taste, stellen Sie mit diesen Tasten die Metronomfunktionen Betonung der Glocke, Tempo und Metronomklang ein.

9. [REVERB]-Taste und LED Zum Einstellen des Halleffekts (S.59). Drcken Sie diese Taste gemeinsam mit der [SONG]-Taste, um eines der integrierten Sounddemos abzuspielen (S.56 ).

10.[FUNC.]-Taste und LED Stellt das Instrument in den Funktionsmodus, um verschiedene Einstellungen und Aktionen, die nichts mit der Darbietung von Musik zu tun haben, auszufhren. Hierzu zhlen das Speichern oder Lschen von Songs, die Auswahl der Stimmung, (S.74).

11.Multidisplay Anhand der beleuchteten [DISPLAY]-LED erken- nen Sie, welche Art von Informationen angezeigt wird. Zu diesen Informationen zhlen das Met-

43 11

5 6 7 8

9 12 13 1410

2

1

53

5

ronomtempo, das Recordertempo, die Nummer des aufgenommenen Songs, der Takt des Songs usw.

12.[]- und []-Taste Mit diesen Tasten regeln Sie das Metronom- und Recordertempo sowie verschiedene andere Einstel- lungen.

13.[ ]-Taste Schaltet das Metronom EIN oder AUS. Drcken Sie die Taste, um die Metronomeinstellungen zu ndern (S.60).

14.[PART 1]- und [PART 2]-Taste Zur Auswahl des Teils, der aufgenommen oder gespielt wird (S.63). Bei blinkender [ ]-Taste regeln Sie mit diesen Tas- ten die Lautstrke, die Taktart und andere Einstel- lungen.

Rckseite

1. MIDI-Anschlsse Sie knnen diese Anschlsse mit MIDI-Gerten wie Synthesizern, Sequenzern oder Rhythmusm- aschinen verbinden, um Daten zu senden und zu empfangen (S.68). IN Dieser Anschluss empfngt MIDI-Meldungen. Verbinden Sie diesen Anschluss mit dem MIDI OUT-Anschluss des externen MIDI-Gerts, das das HT-70 steuert. OUT Dieser Anschluss gibt MIDI-Meldungen aus. Verbinden Sie diesen Anschluss mit dem MIDI IN- Anschluss des externen MIDI-Gerts, das das HT- 70 steuern soll.

2. USB-Anschluss Sie knnen ein USB-Kabel verwenden, um diesen Anschluss direkt mit Ihrem Computer zu verbin- den, um Daten zu bertragen (S.70).

3. LINE OUT-Buchse Sie knnen diese Buchse mit der Eingangsbuchse Ihres verstrkten Lautsprechersystems verbinden und das HT-70 ber Ihre Anlage hren, oder ihn an

Ihr Aufnahmegert anschlieen und den Sound des HT-70 aufnehmen. Verwenden Sie ein Stereo-Min- istecker-Kabel.

Sie mssen alle Verbindungen bei ausgeschalteten Gerten herstellen. Unvorsichtige Handhabung kann das HT-70 oder angeschlossene Gerte besch- digen oder Fehlfunktionen verursachen.

Verbindungskabel sind getrennt erhltlich. Sie mssen die geeigneten handelsblichen Kabel fr Ihre Ausrstung besorgen.

4. DC12V-Buchse Schlieen Sie hier das mitgelieferte erhltliche Netz- teil an (S.55).

5. Lautsprecheranschluss: Schlieen Sie hier Lautsprecher an.

Beispiele

Bei der Songwiedergabe

Tempo

Song Nr.

Takt (Takt im Song)

Bei AB-Wiederholung

Bei Aufzeichnung im Speicher (Kreisfrmige Bewegung)

Punkt ein/blinkt/aus Ein/ein (auerhalb des Bereichs)/aus

2 43

5

1

4

55

Vorbereitung zum Spielen und Demo-Song

Bevor Sie mit dem Spielen beginnen Netzanschluss

1. Vergewissern Sie sich, dass das HT-70 ausgeschaltet ist.

2. Schlieen Sie das Netzkabel am mitgelieferten Wechselstromadapter an, und verbinden Sie den Gleichstromanschluss des Adapters mit dem 12-V-Gleichstromanschluss des HT-70.

Verwenden Sie ausschlielich das mitgelieferte Wechselstromnetzteil. Bei der Verwendung eines anderen Wechselstromnetzteils wird mglicherweise das Gert beschdigt.

Stummschalten des akustischen Klavierklangs Verwenden Sie die Stummschaltfunktion zum Stummschalten oder Aufheben der Stummschaltung des Akustikpianos. Die Stummschaltfunktion wird entweder elektrisch (Abb. 2.1) oder manuell (Abb. 2.2) aktiviert. Falls die Stummschaltfunktion auf Ihrem Instru- ment keiner dieser Abbildungen entspricht, wenden Sie sich bitte an Ihren Hndler oder einen qualizierten Kundendienstmitarbeiter, um Anweisungen zum Gebrauch zu erhalten.

Alle Funktionen des HT-70 sind verfgbar, ungeachtet ob das akustische Klavier stummge- schaltet ist. Der Abschnitt Verwendung des HT-70 ohne Stummschalten des akustischen Kla- viers auf Seite 127 beschreibt einige der Mglichkeiten zur Verwendung des HT-70 zusammen mit akustischem Klaviersound.

Bei sehr starkem Anschlag kann trotz eingeschalteter Stummschaltung akustischer Klang ertnen.

Falls Sie ber eine elektrische Stummschaltfunktion verfgen Zum Stummschalten des Pianos stellen Sie den Schalter der Stummschaltfunktion am Piano (Abb. 2.1) in die STOP-Position. Die leuchtende MUTING-BAR-LED signalisiert, dass das Piano stumm geschaltet ist. Wenn Sie wieder zum Akustikpiano-Sound zurckke- hren mchten, stellen Sie den Schalter in die FREE-Position, woraufhin die LED erlischt.

Bedienen Sie nicht whrend des Spiels.

Falls Sie ber eine manuelle Stummschaltfunktion verfgen Wie in Abb. 2.2 gezeigt, ziehen Sie den Hebel der Stummschalteinheit an der Unterseite des Klaviaturbodens auf sich zu und senken den Hebel zum Arretieren ab. Um wieder zum herkmmlichen Spielen des akustischen Klaviers zu schalten, stellen Sie den Hebel in die Ausgangsstellung zurck.

Bedienen Sie diesen Hebel nicht whrend des Spiels.

Kopfhrer Die Kopfhrerbuchsen benden sich auf der Vorderseite der Soundelemente(S.53). An diesen Buchsen knnen Kopfhrer mit Standard-Stereosteckern angeschlossen werden. Da zwei Kopfhrerbuchsen vorhanden sind, knnen zwei Personen beim Spielen zuhren.

Bei dem Modell mit Lautsprechern werden diese durch Einstecken des Kopfhrers stummge- schaltet. Verwenden Sie Kopfhrer, wenn der Klang andere in der Nhe stren kann, wie etwa beim ben in der Nacht.

Pianounterseite (HT-70-Rckseite)

an eine Netzsteckdose Netzteil Gleichstromstecker

Abb. 1

Netzkabel fr Netzteil

Abb. 2.1

Abb. 2.2

5

6

Si votre casque utilise un adaptateur 1/4", saisissez la che de l'adaptateur quand vous branchez ou dbranchez votre casque.

Bei Verwendung von Kopfhrern mssen Sie Ihre Ohren schonen, indem Sie langes Hren mit sehr hoher Lautstrke vermeiden.

Wenn das Bedienfeld schlecht lesbar ist ndern Sie den Winkel, um die Lesbarkeit zu verbessern. Lsen Sie einfach den Bolzen und die Schraube auf beiden Seiten (links und rechts), passen Sie den Winkel nach Wun- sch an, und ziehen Sie die Schrauben wieder fest.

Vergewissern Sie sich, dass die Schrauben nach dem Einstellen fest angezogen sind.

Gert einschalten Drcken Sie [POWER], um das Gert einzuschalten. Nach dem Einschalten ist das Multi- display beleuchtet. Zum Ausschalten drcken Sie erneut die [POWER]-Taste, woraufhin das Multidisplay erlischt.

Beim Ausschalten werden bis auf die im nichtchtigen Speicher gespeicherten Einstellungen alle Einstellungen auf die Standardwerte zurckgesetzt. Aufgenommene Musikdaten bleiben im Speicher erhalten und gehen nicht verloren.

Einschalten des Gerts Drehen Sie den [VOLUME]-Knopf zur Einstellung der Lautstrke. (Siehe Abb. 4.)

Dies steuert die Lautstrke, die von den Kopfhrerbuchsen aus- gegeben wird. Drehen Sie den Knopf nach links zum Senken der Lautstrke oder nach rechts zum Steigern der Lautstrke.

Bei dem Modell mit Lautsprechern steuert er auch die Lautstrke, die von den Lautsprechern ausgegeben wird. Bei manchen Klngen kann der Klang von den Lautsprechern verzerrt sein, wenn Sie die Lautstrke auf Maximalstellung stellen.

Anhren von Sounddemos Im HT-70 sind zehn Demosongs gespeichert, um die acht verschiedenen Sounds vorzustellen.

Hren der Sound-Demos Liste der Sound-Demos

Nr. Sound Songtitel Komponist

1 PIANO1 La Campanella F.Liszt

2 PIANO1 The Path Of Truth Jordan Rudess

3 PIANO1 Rhapsody in Blue G.Gershwin

4 PIANO2 Someone To Watch Over Me G.Gershwin

5 E.PIANO1 Ramble M.Sakaguchi

6 E.PIANO2 KORG Original KORG

7 HARPSI. Invention No.8 J.S.Bach

8 P.ORGAN Toccata in D moll J.S.Bach

9 E.ORGAN KORG Original KORG

10 STRINGS First Snow M.Sakaguchi

Abb. 3

Schraube Bolzen

Pianounterseite

Abb. 4 Weicher Lauter

1. Drcken Sie gleichzeitig den [SONG]-Taste und [REVERB]-Taste Der [SONG]-Taste leuchten auf.

2. Verwenden Sie den Sound-Wahlschalter zum Whlen des zu Hren gewnschten Songs aus der obigen Liste; der gewhlte Demo-Song beginnt zu spielen. Wenn Sie nicht innerhalb von drei Sekunden einen Song whlen, beginnen die Songs der Reihe nach zu spielen, beginnend mit Sound-Demo-Nummer 1. Wenn die Sound- Demo-Nummer 10 fertig abgespielt ist, schaltet die Wiedergabe auf Sound-Demo- Nummer 1 und setzt fort.

Zur Auswahl von Demo 2 oder 3 stellen Sie den Auswahlknopf auf Piano 1, und drcken Sie anschlieend [] oder [].

3. Wenn die gewhlte Sound-Demo fertig abgespielt ist, wird die Wiedergabe mit dem nchsten Song fortgesetzt.

4. Drcken Sie whrend der Demowiedergabe die [ ]-Taste, um die Wiedergabe zu unterbrechen oder fortzusetzen. (Die Tastenanzeige leuchtet whrend der Wiedergabe und blinkt whrend einer Pause.) Drcken Sie die []-Taste, um die Wiedergabe zu beenden und zum Anfang des Demos zurckzukehren.

5. Zum Stoppen der Wiedergabe drcken Sie den [SONG]-Taste. Der [SONG]-Taste erlschen, die Wiedergabe stoppt.

Wenn Sie auf eine andere Sound-Demo schalten wollen, verwenden Sie den Sound- Wahlschalter zum Umschalten des Demo-Songs. Wenn z.B. Sound-Demo Nr. 1 spielt, aber Sie auf Nr. 10 umschalten wollen, drehen Sie einfach den Sound-Wahlschalter auf STRINGS. Die Sound-Demo-Wiedergabe schaltet auf Nr. 10 um und setzt das Spiel fort. Alternativ, und mit den [][]]-Taste einen Song whlen. Nachdem Sie einen Song gewhlt haben. In diesem Fall wird die Posi- tion des Sound-Wahlschalters ignoriert.

Beim ndern der Auswahl beginnt die Demowiedergabe automatisch ([ ] leuchtet).

Whrend eine Sound-Demo spielt, knnen Sie auf dem Keyboard den gleichen Sound spielen, aber Sie knnen nicht auf einen anderen Sound umschalten.

Sie knnen nicht die Reverb-Einstellung ndern, whrend eine Sound-Demo spielt.

Sie knnen nicht das Tempo einer Sound-Demo ndern.

12

1, 4 2

2

57

5

Spielen des HT-70

Auswhlen eines Sounds

Whlen Sie mit dem Soundknopf einen Sound.

Verwenden der Pedale Auf die Sounds des HT-70 knnen das Haltepedal, Sostenutopedal und Softpedal angewendet werden. Mit den Pedalen des (akustischen) Klaviers verleihen Sie Ihrem Spiel mehr Ausdruck.

Haltepedal Die Noten werden gehalten, whrend Sie das Pedal gedrckt halten, was eine reiche Resonanz erzeugt. Die Tiefe des Pedaldrucks steuert die Resonanzstrke (Halbpedalef- fekt).

Sostenutopedal Mit diesem Pedal lassen Sie bestimmte Noten ausklingen. Whrend des Drckens dieses Pedals klingen alle gespielten Noten nach, whrend alle Noten, die im ungedrckten Zustand des Pedals gespielt werden, nicht nachklingen.

Softpedal Der Sound wird weicher und milder, whrend Sie das Pedal gedrckt halten. Die Tiefe des Pedaldrucks steuert die Strke der Dmpfung, die angelegt wird (Halbpedalef- fekt).

Sound Beschreibung

PIANO1 Ein hochwertiger Flgel-Sound von hervorragender Brillanz

PIANO2 Konzertgel mit vollen Bssen

E.PIANO1 Ein leichter und klarer Sound eines E-Pianos

E.PIANO2 Ein knackiger Klavier-Sound mit gutem Ansprechverhalten

HARPSI. Ein klasischer und realistischer Cembalo-Sound

P.ORGAN Ein ernster Pfeifenorgel-Sound

E.ORGAN Funky Jazzorgel

STRINGS Ein Ensemble-Sound mit Geige und anderen

8

Hinzufgen von Nachhall zum Sound (Reverb) Sie knnen Nachhall (Reverb) zum Sound hinzufgen, um das grozgige Raumgefhl einer typischen Vorfhrung in einer Konzerthalle zu schaffen.

Mit der [REVERB]-Taste aktivieren und deaktivieren Sie den Hall. Beim ndern der Einstellung kopiert das HC-70 die neue Einstellung in den Speicher. Das Multidisplay signalisiert, wenn ein Speichervorgang stattndet (S.53).

Schalten Sie whrend des Speicherns das HT-70 nicht aus. Hierdurch knnen gespeicherte Einstellungen und Songdaten verloren gehen oder beschdigt werden.

Einstellen der Halltiefe

1. Drcken Sie die [REVERB]-Taste zirka eine Sekunde lang. Die LED der Taste blinkt.

2. Whlen Sie mit [] oder [] die gewnschte Tiefe aus. Auf dem Multidisplay steht die aktuelle Einstellung. Auf dem Display steht 01 (gering), 02 (Standard) oder 03 (stark).

3. Nachdem Sie die Einstellung vorgenommen haben, erscheint bei erneutem Drcken von [REVERB] wieder die ursprngliche Anzeige. Beim ndern der Einstellung kopiert das HT-70 die neue Einstellung in den Speicher. Das Multidisplay signalisiert, wenn ein Speichervorgang stattndet (S.53). Nach dem Schreibvorgang leuchtet die [REVERB]-LED oder sie erlischt, je nachdem, ob der Hall fr den ausgewhlten Sound aktiviert oder deaktiviert ist.

Schalten Sie whrend des Speicherns das HT-70 nicht aus. Hierdurch knnen gespeicherte Einstellungen und Songdaten verloren gehen oder beschdigt werden.

Wenn Sie vor dem Speichern der neuen Halltiefeeinstellung einen anderen Sound auswhlen oder das Gert ausschalten, wird die Halltiefe auf die ursprngliche Einstellung zurckgesetzt.

Sie knnen die Einstellungen fr Reverb ein/aus und die Tiefeneinstellungen getrennt fr jeden Sound einstellen. Mit den werkseitigen Einstellungen sind die Parameter typisch fr jeden Sound eingestellt.

Da die Sound Piano 1 die Saitenresonanz eines akustishcen Klaviers simulieren, verbleibt ein geringer Reverb-Betrach auch wenn Reverb ausgeschaltet wird.

59

6

Zusammen mit dem Metronom spielen Es ist praktisch, das Metronom zu verwenden, wenn Sie in einem genauen Tempo spielen wollen.

Zum Einschalten des Metronoms

1. Drcken Sie den [ ]-Taste. Der [ ]-Taste leuchtet auf.

2. Zum Stoppen des Metronoms drcken Sie den [ ]-Taste erneut. Der [ ]-Taste erlischt.

ndern der Metronomeinstellungen Die hier beschriebenen Einstellungen werden mit Ausnahme des Tempos und der Taktart auch im ausgeschalteten Zustand beibehalten. Durch Drcken von [ ] nach einer nderung schreibt das HT-70 den neuen Wert automatisch in den nichtchtigen Speicher. Das Multidis- play signalisiert, wenn ein Speichervorgang stattndet (S.53 ).

Schalten Sie whrend des Speicherns das HT-70 nicht aus. Hierdurch knnen gespeicherte Ein- stellungen und Songdaten verloren gehen oder beschdigt werden.

ndern der Tempoeinstellung

1. Drcken Sie die [ ]-Taste zirka eine Sekunde lang. Die Taste beginnt zu blinken.

2. Die TEMPO-LED (neben der [DISPLAY]-Taste) leuchtet, und auf dem Multidisplay erscheint die aktuelle Tempoeinstellung. Drcken Sie [TEMPO ()], wenn die TEMPO-LED nicht leuchtet.

3. Whlen Sie mit [] oder [] das gewnschte Tempo aus. Drcken Sie die Taste kurz, um den Wert schrittweise zu ndern. Halten Sie die Taste gedrckt, um den Wert fortlaufend zu ndern. Drcken Sie [] und [] gleichzeitig, um das Tempo auf die Standardeinstellung zurckzusetzen. Fr das Tempo kann ein Wert von ( =) 4 bis 250 gewhlt werden.

4. Drcken Sie noch einmal [ ], wenn Sie den Wert festgelegt haben. Das HT-70 kehrt in den vorherigen Zustand zurck. Die [ ]-Taste hrt auf zu blinken (sie erlischt oder leuchtet).

1, 2

1, 4

2

3

3

0

ndern der Lautstrke

1. Drcken Sie die [ ]-Taste zirka eine Sekunde lang. Die Taste beginnt zu blinken.

2. Drcken Sie die [VOL. (PART 2)]-Taste. Die Taste leuchtet, und auf dem Multidisplay erscheint die aktuelle Lautstrke.

3. Whlen Sie mit [] oder [] die gewnschte Lautstrke aus. Drcken Sie die Taste kurz, um den Wert schrittweise zu ndern. Halten Sie die Taste gedrckt, um den Wert fortlaufend zu ndern. Die Lautstrke kann von 0 bis 127 gewhlt werden.

4. Drcken Sie noch einmal [ ], wenn Sie den Wert festgelegt haben. Das HT-70 kehrt in den vorherigen Zustand zurck. Die [ ]-Taste hrt auf zu blinken (sie erlischt oder leuchtet).

ndern der Taktart

1. Drcken Sie die [ ]-Taste zirka eine Sekunde lang. Die Taste beginnt zu blinken.

2. Drcken Sie die [BEAT (PART 1)]-Taste. Die Taste leuchtet, und auf dem Multidisplay erscheint die aktuelle Taktart.

3. Whlen Sie mit [] oder [] die gewnschte Taktart aus.

4. Drcken Sie noch einmal [ ], wenn Sie den Wert festgelegt haben Das HT-70 kehrt in den vorherigen Zustand zurck. Die [ ]-Taste hrt auf zu blinken (sie erlischt oder leuchtet).

ndern der Betonung

1. Drcken Sie die [ ]-Taste zirka eine Sekunde lang. Die Taste beginnt zu blinken.

2. Drcken Sie die [BELL()] -Taste. Die Taste leuchtet, und auf dem Multidisplay erscheint die aktuelle Betonung.

Display 1-2 2-2 1-4 2-4 3-4 4-4 6-8

Taktma 1/2 2/2 1/4 2/4 3/4 4/4 6/8

1, 4 2

3

3

1, 4 2

3

3

1, 4

2

3

3

61

6

3. Whlen Sie mit [] oder [] den gewnschten Klang fr die Betonung aus.

* Bei der Auswahl eines mechanischen Metronoms erfolgt die Betonung mit der Glocke. Bei der Auswahl eines digitalen Metronoms erfolgt die Betonung mit einem Digitalton. (Siehe "ndern des Metronomklangs" auf Seite 62.)

4. Drcken Sie noch einmal [ ], wenn Sie den Wert festgelegt haben. Das HT-70 kehrt in den vorherigen Zustand zurck. Die [ ]-Taste hrt auf zu blinken (sie erlischt oder leuchtet).

ndern des Metronomklangs

1. Drcken Sie die [ ]-Taste zirka eine Sekunde lang. Die Taste beginnt zu blinken.

2. Drcken Sie die [SOUND( )] -Taste. Die Taste leuchtet, und auf dem Multidisplay erscheint die aktuelle Klang.

3. Whlen Sie mit [] oder [] den gewnschten Klang fr die Klang.

4. Drcken Sie noch einmal [ ], wenn Sie den Wert festgelegt haben. Das HT-70 kehrt in den vorherigen Zustand zurck. Die [ ]-Taste hrt auf zu blinken (sie erlischt oder leuchtet).

Weitere Funktionen Neben den vorgestellten Funktionen bietet das HT-70 auch noch eine Reihe anderer nt- zlicher Funktionen fr das Spielen. Informationen hierzu nden Sie auf den angegebenen Seiten.

Tonhhenregelung: Schlagen Sie nach unter Einstellen der Tonhhe auf Seite 66.

Stimmung: Schlagen Sie nach unter Whlen einer Stimmung auf Seite 66.

Brillianz: Schlagen Sie nach unter Einstellen der Helligkeit des Sounds (Brillanz) auf Seite 66.

Touch-Control-Einstellung: Schlagen Sie nach unter Anpassen der Tastat- urempndlichkeit auf Seite 67.

Transponieren: Schlagen Sie nach unter Andern der Tonart (Transponieren) auf Seite 67.

Zurckstellen: Schlagen Sie nach unter Zurckstellen auf werkseitige Einstellun- gen auf Seite 67.

Display oFF on1 on2

Betonung Keine Standard Glocke oder Digitalton*

Display S1 S2

Klang Mechanisch Digital

1, 4

2

3

3

2

Aufnehmen und Wiedergeben Ihres Spiels Das HT-70 bietet einen Recorder, der Ihr Tastenspiel so leicht aufzeichnen und abspielen kann wie ein Kassettenrecorder. Es gibt zwei Aufnahme-Parts. Sie knnen diese verwenden, um separate Songs aufzunehmen oder um separat die Parts der linken und rechten Hand des gle- ichen Songs aufzunehmen und dann beide Parts gleichzeitig abzuspielen.

Wenn Sie auf einem vorher aufgezeichneten Part aufnehmen wollen, werden die vorherigen Daten gelscht und durch das neue Spiel ersetzt. Bevor Sie fort- fahren, stellen Sie sicher, dass es in Ordnung ist, das vorher aufgezeichnete Spiel zu lschen.

Eingespieltes Material wird so lange gespeichert, bis der Speicher voll ist.

Aufnehmen Ihres Spiels Warten Sie nach dem Einspielen oder Bearbeiten von Material, bis die neuen Daten vom HT-70 im nichtchtigen Speicher gespeichert sind, bevor Sie das Gert ausschalten. Wenn Sie das Gert whrend eines Schreibvorgangs ausschalten, knnen aufgenommene Songs, Daten und Einstellungen verloren gehen oder beschdigt werden.

Schnellaufnahme (Aufnahme eines neuen Songs) Der integrierte Recorder ist einfach zu bedienen. Wir beginnen mit einer schnellen Aufnahme.

1. Whlen Sie mit dem Soundknopf den Sound, der aufgenommen werden soll.

2. Drcken Sie gleichzeitig die Tasten [] und [ ]. Die []-Taste leuchtet, und die Tasten [PART 1] und [PART 2] blinken.

3. Auf dem Multidisplay erscheint eine leere, blinkende Benutzersongnummer. Sind keine freien Songnummern mehr verfgbar, erscheint die bereits ver- wendete Nummer U01 auf dem Display.

4. Drcken Sie [] oder [], um den Song unter einer anderen Songnummer aufzunehmen. Whlen Sie eine Nummer zwischen U01 und U99.

Leere Songnummern erscheinen auf dem Multidisplay blinkend. Nummern, die bereits in Verwendung sind, leuchten dauerhaft.

Bei Auswahl einer bereits verwendeten Songnummer wird die vorhan- dene Aufnahme durch die neue Aufnahme ersetzt.

5. Drcken Sie eine Taste auf der Tastatur, oder drcken Sie [ ], um die Aufnahme zu starten. Sie knnen die Aufnahme auch starten, indem Sie an den ausgewhlten MIDI-Kanal einen MIDI-Befehl senden (S.68).

Wenn Sie die Aufnahme mit dem Metronom einspielen mchten, drcken Sie [ ] (bis die Taste leuchtet), und drcken Sie [ ]. Das HT-70 gibt zwei Takte vor, bevor die Aufnahme automatisch beginnt. (Informationen ber das Festlegen der Taktart, des Tempos und anderer Metronomfunktionen nden Sie unter ndern der Met- ronomeinstellungen auf Seite 60.)

6. Zum Beenden der Aufnahme drcken Sie [], [ ] oder []. Die [PART 1]-Taste erlischt, und die [PART 2]-Taste leuchtet.

Nach dem Beenden der Aufnahme speichert das HT-70 die neuen Daten automatisch im nichtchtigen Speicher. Das Multidisplay signalisiert, wenn ein Speichervorgang stattndet.

So fgen Sie einem mittels Schnellaufnahme aufgenomme- nen Song Musikdaten hinzu

Wenn Sie nach der Schnellaufnahme die Songauswahl gendert haben, mssen Sie vor dem Aufnehmen weiterer Parts zu dieser Aufnahme erst wieder diesen Song auswhlen. Fhren Sie die folgenden Schritte 1 bis 4 aus, um zu dem Song zurckzuwechseln.

1. Drcken Sie []. Die []-Taste leuchtet.

2. Falls notwendig, whlen Sie mit dem Soundknopf den Sound, der aufgenom- men werden soll.

3. Drcken Sie die [PART 1]-Taste so lange, bis sie blinkt.

4. Drcken Sie eine Taste auf der Tastatur, oder drcken Sie [ ], um die Aufnahme zu starten.

5. Zum Beenden der Aufnahme drcken Sie [], [ ] oder []. Die [PART 1]-Taste leuchtet, und das HT-70 schreibt die aufgenommenen Daten automatisch in den nichtchtigen Songspeicher. Das Multidisplay signalisiert, wenn ein Speichervorgang stattndet.

Aufnahme einer Darbietung

So nehmen Sie einen neuen Song auf Sie starten eine neue Aufnahme, indem Sie gleichzeitig die Tasten [] und [ ] drcken siehe Seite 63 unter Schnellaufnahme (Aufnahme eines neuen Songs). Benden sich derzeit keine Benutzersongs im Speicher, knnen Sie die Schnellaufnahme auch durch Drcken von nur der []-Taste starten.

Auf dem Multidisplay erscheint die Meldung E07, wenn der Speicher voll ist. Sie mssen zuerst mindestens einen vorhandenen Song lschen, um weitere aufgenommene Daten zu speichern (S.64).

So nehmen Sie einen weiteren Part zu einem vorhandenen Song auf Der integrierte Recorder ermglicht die Aufnahme von zwei Parts pro Song. Wenn Sie eine Schnellaufnahme durchfhren, ohne entweder die [PART 1]- oder [PART 2]-Taste zu drcken, wird automatisch Part 2 aufgenommen. In diesem Fall knnen Sie spter weitere Musikdaten unter Part 1 fr diesen Song aufneh- men. Mglicherweise nehmen Sie zahlreiche Benutzersongs nur mit einem einzelnen Part auf. Sie knnen dann zu einem spteren Zeitpunkt in die leeren Parts dieser Songs weitere Daten aufnehmen. Mglicherweise haben Sie auch zahlreiche Songs mit zwei Parts aufgenommen. Sie knnen zu einem spteren Zeitpunkt jeden Part berspielen oder einen Part auch lschen und erneut aufnehmen (S.64). Die Anzeigeleuchte einer PART-Taste signalisiert den Status eines Parts wie folgt.

So fgen Sie einem aufgenommenen Song weitere Musik- daten hinzu 1. Drcken Sie [SONG].

Die [SONG]-LED leuchtet.

2. Whlen Sie mit [] oder [] den Benutzersong, dem Sie einen Part hinzuf- gen mchten. Um Ihnen die Auswahl zu erleichtern knnen Sie in einen ausgewhlten Song kurz reinhren, indem Sie [ ] drcken.

3. Drcken Sie erneut [SONG]. Die [SONG]-LED erlischt.

4. Drcken Sie []. Die []-Taste leuchtet. Die PART-Taste des bereits aufgenommenen Parts leuchtet. Drcken Sie die PART-Taste so lange, bis sie blinkt.

Wurden beide Parts des Songs bereits aufgenommen, knnen Sie zu dem Song erst weitere Daten aufnehmen, nachdem Sie einen der Parts gelscht haben (Siehe " Lschen eines Parts" auf Seite 64).

5. Drcken Sie [] oder [], um den Song unter einer anderen Songnummer aufzunehmen. Whlen Sie eine Nummer zwischen U01 und U99.

Leere Songnummern erscheinen auf dem Multidisplay blinkend. Nummern, die bereits in Verwendung sind, erscheinen nicht blinkend.

[PART 1] / [PART 2] Taste Part-Status

Aus Der Part ist leer oder stumm geschaltet. Dieser Part ist nicht aufnahmebereit.

Leuchtet Der Part enthlt aufgenommene Daten. Dieser Part ist nicht aufnahmebereit.

Blinkt Dieser Part ist aufnahmebereit.

63

6

Bei Auswahl einer bereits verwendeten Songnummer wird der vorhan- dene Song durch die neue Aufnahme ersetzt.

6. Drcken Sie eine Taste auf der Tastatur, oder drcken Sie [ ], um die Aufnahme zu starten.

7. Zum Beenden der Aufnahme drcken Sie [], [ ] oder []. Nach dem Beenden der Aufnahme speichert das HT-70 die neuen Daten automatisch im nichtchtigen Speicher. Das Multidisplay signalisiert, wenn ein Speichervorgang stattndet.

Wichtige Informationen ber Aufnahmen

Wenn Sie neue Musikdaten in den leeren Part eines aufgenommenen Songs aufnehmen, dient der lngere Part als Songlnge (in Takten).

Die Aufnahme erfolgt mit dem Sound, der mit dem Soundknopf whrend der Aufnahme (whrend die []-Taste leuchtet) ausgewhlt wurde. Sie kn- nen den Sound mit dem Soundknopf whrend des Auftakts oder jederzeit whrend der Aufnahme ndern (whrend die PART-Taste blinkt und die []-Taste leuchtet).

Wenn Sie whrend einer laufenden Aufnahme das Tempo ndern, wird die Temponderung der Aufnahme hinzugefgt.

So ndern Sie das Tempo whrend der Aufnahme: Drcken Sie, falls not- wendig, [DISPLAY], bis die TEMPO-LED leuchtet, und ndern Sie anschlieend mit der Taste [] oder [] den auf dem Multidisplay angezeigten Tempowert.

Sie knnen eine Taktart aufnehmen, die jedoch nach der Aufnahme des Songs nicht mehr gendert werden kann. Wenn Sie zu einer vorhandenen Aufnahme einen weiteren Part aufnehmen, knnen Sie fr diesen neuen Part eine andere Taktart whlen.

So legen Sie den Starttakt fr eine Aufnahme fest: Vor Beginn der Aufnahme drcken Sie, falls notwendig, [DISPLAY], bis die MEASURE-LED leuchtet. ndern Sie anschlieend mit der Taste [] oder [] die auf dem Multidis- play angezeigte Taktzahl.

Speichern eines aufgenommenen Songs Nach Abschluss einer Aufnahme speichert das HT-70 automatisch die auf- genommenen Musikdaten als einen Benutzersong. Das HT-70 benennt den Song mit der zu Beginn der Aufnahme ausgewhlten Nummer.

Das HT-70 kann bis zu 99 Benutzersongs speichern. Jeder Song kann bis zu 999 Takte lang sein und bis zu 45.000 Noten umfassen.

Kopieren eines Songs Das HT-70 speichert die aufgenommenen Daten unter der fr die Aufnahme gewhlten Songnummer. Nach Abschluss der Aufnahme knnen Sie keine andere Songnummer whlen. Wenn Sie mchten, knnen Sie jedoch den gespe- icherten Song an einem anderen Speicherort (unter einer anderen Songnummer) speichern.

1. Drcken Sie nach abgeschlossener Aufnahme auf [FUNC.]. Die [FUNC.]-LED leuchtet.

2. Drcken Sie [DISPLAY]. Auf dem Multidisplay erscheint SAv. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die Zielsong- nummer.

3. Whlen Sie mit [] oder [] die gewnschte Zielsongnummer. Auf dem Multidisplay erscheint die ausgewhlte Songnummer. Derzeit nicht zugewiesene Songnummern blinken, whrend bereits verwendete Songnummern dauerhaft leuchten.

Wenn Sie eine neue Aufnahme unter einer Songnummer speichern, die bereits in Verwendung ist, wird dieser Song berschrieben, und er geht verloren. berschreiben Sie keine Songs, die Sie behalten mchten.

4. Drcken Sie []. Das HT-70 schreibt die Songdaten in den Speicher. Das Multidisplay signal- isiert die Ausfhrung des Schreibvorgangs.

5. Drcken Sie erneut [FUNC.], nachdem der Song gespeicher t wurde (wenn das Multidisplay keinen Schreibvorgang mehr signalisiert). Die [FUNC.]-LED erlischt, und das HT-70 kehrt zum vorherigen Status zurck.

Lschen eines Songs 1. Drcken Sie nach abgeschlossener Aufnahme auf [FUNC.].

Die [FUNC.]-LED leuchtet.

2. Drcken Sie mindestens einmal die [DISPLAY]-Taste, bis auf dem Multidis- play dEL erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Benutzersongnummer.

3. Whlen Sie mit [] oder [] den Song, den Sie lschen mchten.

4. Drcken Sie [], um den Song zu lschen. Das Multidisplay signalisiert den Schreibvorgang, whrend der Song gelscht wird.

5. Drcken Sie erneut [FUNC.], nachdem der Song gelscht wurde (wenn das Multidisplay keinen Schreibvorgang mehr signalisiert). Die [FUNC.]-LED erlischt, und das HT-70 kehrt zum vorherigen Status zurck.

Lschen eines Parts 1. Drcken Sie nach abgeschlossener Aufnahme auf [FUNC.].

Die [FUNC.]-LED leuchtet.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay P.dL erscheint. Beim Loslassen der Taste erscheinen auf dem Multidisplay Partinforma- tionen.

3. Whlen Sie mit [] oder [] den Part/die Parts, den/die Sie lschen mchten.

4. Drcken Sie [], um den Part/die Parts zu lschen. Das Multidisplay signalisiert den Schreibvorgang, whrend der Song gelscht wird.

5. Drcken Sie erneut [FUNC.], nachdem der Song gelscht wurde (wenn das Multidisplay keinen Schreibvorgang mehr signalisiert). Die [FUNC.]-LED erlischt, und das HT-70 kehrt zum vorherigen Status zurck.

So zeigen Sie an, wie viele Daten noch auf- genommen werden knnen

Drcken Sie whrend der Aufnahme oder whrend des Aufnahme-Standby- Modus (wenn die []-LED leuchtet) die [FUNC.]-Taste. Auf dem Multidisplay erscheint der freie Speicherplatz in Prozent. Diese Angabe wird ca. fnf Sekunden lang angezeigt. Bei 100 % verfgbarem Speicherplatz knnen Sie in bis zu 999 Takten ungefhr 45.000 Noten aufnehmen. Zur lngerfristigen Aufbewahrung von aufgenommenen Musikdaten empfehlen wir die Verwendung einer USB-Verbindung zum Speichern und Verwalten Ihrer Daten (S.71).

Display ALL P1 P2

Part(s) Beide Parts Part 2 Part 2

4

Abspielen von Songs Auswahl eines Songs 1. Drcken Sie [SONG].

Die [SONG]-Taste und die SONG-LED der [DISPLAY]-Taste leuchten. Auf dem Multidisplay erscheint die Benutzersongnummer.

Beim ersten Drcken von [SONG] nach dem Einschalten erscheint auf dem Multidisplay die niedrigste Songnummer, die einem Song zugewie- sen ist.

Wurden bei der aktuellen Sitzung bereits Songs ausgewhlt, erscheint auf dem Multidisplay die Songnummer des zuletzt ausgewhlten Songs.

Auf dem Multidisplay erscheint ---, wenn bisher noch kein Song gespeichert wurde.

2. Whlen Sie mit [] oder [] die gewnschte Songnummer auf dem Multidis- play.

3. Drcken Sie [ ], um die Wiedergabe zu starten. Das HT-70 beginnt mit der Wiedergabe des ausgewhlten Songs.

Abspielen von Song-Parts Nachdem Sie einen abzuspielenden Song ausgewhlt haben, leuchtet die PART- Taste eines Parts, der Musikdaten enthlt. Leuchtet eine PART-Taste nicht, ist dieser Part leer. Whrend der Wiedergabe knnen Sie die Wiedergabe eines Parts vollstndig oder teilweise stumm schalten, indem Sie die jeweilige PART- Taste drcken (die PART-Taste erlischt).

So regeln Sie die Lautstrke eines stumm geschalteten Parts 1. Drcken Sie [FUNC.], whrend die [SONG]-LED leuchtet.

Die [FUNC.]-LED leuchtet.

2. Drcken Sie die PART-Taste des stumm zu schaltenden Parts. Die Taste erlischt.

3. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay P.Lv erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktu- elle Lautstrkeeinstellung. (Die Voreinstellung lautet 30.)

4. Whlen Sie mit [] oder [] die gewnschte Lautstrke aus. Whlen Sie einen Wert zwischen 00 (vollstndig stumm) und 90.

5. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzus- chlieen. Die [FUNC.]-LED erlischt.

Unterbrechen der Songwiedergabe 1. Drcken Sie whrend der Songwiedergabe [ ], um die Wiedergabe zu

unterbrechen. Die Taste beginnt zu blinken.

2. Drcken Sie [ ] erneut, um die Wiedergabe fortzusetzen. Die Taste leuchtet dauerhaft, und die TEMPO-LED blinkt synchron mit dem Tempo.

Fortsetzen der Songwiedergabe 1. Drcken Sie whrend der Songwiedergabe [], um die Songwiedergabe zu

beenden. Die Songposition kehrt zum Songanfang zurck.

2. Drcken Sie [ ], um den Song von Anfang an zu spielen.

ndern des Tempos eines abgespielten Songs 1. Drcken Sie mehrmals [DISPLAY], bis die TEMPO-LED leuchtet.

Auf dem Multidisplay steht der aktuelle Tempowert.

2. Whlen Sie mit [] oder [] das gewnschte Tempo aus. Drcken Sie die Taste kurz, um den Wert schrittweise zu ndern. Halten Sie die Taste gedrckt, um den Wert fortlaufend zu ndern. Fr das Tempo kann ein Wert von ( =) 4 bis 250 gewhlt werden.

Navigation zu einer anderen Position (Takt) 1. Drcken Sie mehrmals [DISPLAY], bis die MEASURE-LED leuchtet.

Auf dem Multidisplay steht die aktuelle Taktnummer.

2. Whlen Sie mit [] oder [] einen anderen Takt aus.

3. Wenn Sie bei unterbrochener Wiedergabe zu einem anderen Takt wechseln, ndert sich der Songstatus von beendet zu unterbrochen (und ( ) beginnt zu blinken). Drcken Sie ( ), um den Song ab der neuen Position abzus- pielen.

Sie knnen zur Startposition eines Benutzersongs zurckkehren (Takt 001), indem Sie die Tasten [] und [] gleichzeitig drcken.

So wiederholen Sie die Wiedergabe eines bestimmten Songabschnitts (AB Repeat)

Sie knnen einen bestimmten Songabschnitt wiederholt abspielen. Hierzu legen Sie den ersten und letzten Takt des Abschnitts fest. Verfahren Sie folgendermaen.

1. Drcken Sie [FUNC.], whrend die [SONG]-LED leuchtet. Die [FUNC.]-LED leuchtet.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay Ab.r erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay der Wieder- holstatus. (Die Voreinstellung lautet oFF.)

3. Drcken Sie [] oder [], um die Wiederholfunktion zu aktivieren. Unten rechts auf dem Multidisplay erscheint ein Punkt.

4. Drcken Sie erneut [DISPLAY]. Auf dem Multidisplay erscheint A. Nach dem Loslassen der Taste erscheint auf dem Multidisplay der aktuelle erste Takt. (Die Voreinstellung lautet 001.)

5. Whlen Sie mit [] oder [] den gewnschten ersten Takt aus.

6. Drcken Sie erneut [DISPLAY]. Auf dem Multidisplay erscheint b. Nach dem Loslassen der Taste erscheint auf dem Multidisplay der aktuelle letzte Takt. (Die Voreinstellung lautet 001.)

7. Whlen Sie mit [] oder [] den gewnschten letzten Takt aus.

8. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die [FUNC.]-LED erlischt.

9. Drcken Sie [ ], um die wiederholte Wiedergabe zu starten. Die Wieder- gabe beginnt ab dem ersten Takt des Abschnitts und wird bis zum letzten Takt des Abschnitts fortgesetzt. Nach dem letzten Takt wird die Wiedergabe ab dem ersten Takt des Abschnitts wiederholt. Der Punkt unten rechts auf dem Multidisplay leuchtet dauerhaft whrend der Loop-Wiedergabe innerhalb des AB-Bereichs und blinkt whrend der Wiedergabe auerhalb dieses Bereichs.

10. Drcken Sie [] oder [] (siehe Schritt 3), um die wiederholte Wiedergabe abzubrechen. Der Punkt auf dem Multidisplay wird ausgeblendet.

Whrend der wiederholten AB-Wiedergabe erscheinen im Multidisplay der Punkt unten rechts sowie das Tempo, die Songnummer und der Takt (S.53). Der Punkt ist auch dann sichtbar, wenn Sie die Songfunktionen einrichten (S.74).

Die Wiederholfunktion wird automatisch deaktiviert (und der erste und letzte Takt werden auf 001 zurckgesetzt), wenn Sie einen anderen Song auswhlen, eine Aufnahme starten oder einen anderen Vorgang beginnen.

65

6

Weitere Funktionen Das E-Piano HT-70 bietet zahlreiche bequeme Funktionen, um den Sound, die Eigenschaften und den Betrieb des Instruments anzupassen.

Einstellen der Tonhhe Mit der integrierten Tonhhenregelung knnen Sie die Tonhhe des HT-70 feineinstellen. Verwenden Sie diese Funktion zum Beispiel, um die Tonhhe des HT-70 an die Tonhhe anderer Instrumente anzupassen. Sie knnen die Tonhhe in 0,5-Hz-Schritten insgesamt um bis zu 25 Hz ndern. Die Anpassung erfolgt in Bezug auf die Note A4 mit einer Standardtonhhe von 440,0 Hz, die im Bereich 415,0 Hz bis 465,0 Hz angepasst werden kann.

1. Vergewissern Sie sich, dass die [SONG]-LED nicht leuchtet, und drcken Sie [FUNC.]. Die [FUNC.]-LED leuchtet.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay tUn erscheint. Nach dem Loslassen der Taste erscheinen auf dem Multidisplay die letzten drei Ziffern der aktuellen Tonhhe. (Die Voreinstellung lautet 40.0.)

3. Whlen Sie mit [] oder [] die gewnschte Einstellung aus.

4. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die Einstellung wurde gespeichert, und die [FUNC.]-LED erlischt.

Diese Einstellung wird auch nach dem Ausschalten beibehalten. Durch Drcken von [FUNC.] nach dem ndern der Einstellung speichert das HT- 70 den neuen Wert automatisch im nichtchtigen Speicher. Das Multidis- play signalisiert, wenn ein Speichervorgang stattndet.

Schalten Sie whrend des Speicherns das HT-70 nicht aus. Hierdurch kn- nen gespeicherte Einstellungen und Songdaten verloren gehen oder bes- chdigt werden.

Whlen einer Stimmung Das HT-70 erlaubt es, zwischen mehreren Stimmungen (Skalenabstimmungen) zu whlen. Viele klassische Kompositionen wurde in historischen Zeitperioden geschrieben, in denen die Noten einer Tastaturskala etwas anders gestimmt waren als die heute bliche gleichschwebende Stimmung. Fr historisch authentisches Spiel solcher Musik erlaubt das HT-70 es, die historischen Stim- mungen Werckmeister oder Kirnberger ebenso zu whlen wie die gleichschwe- bende Stimmung moderner Tasteninstrumente.

Werckmeister Dies ist die Werckmeister-III-Skala, erschaffen vom deutschen Organisten und Musiktheoretiker Andreas Werckmeister. Diese Stimmung wurde im spten Barockzeitalter erschaffen, um relativ freie Modulation zwischen Tonarten zu erlauben.

Kirnberger Dies ist die Kirnberger-III-Skala, erschaffen von Johann Phillip Kirnberger am Anfang des 18. Jahrhunderts. Diese Stimmung wird hauptschlich zum Stimmen von Cembalos verwendet.

Gleichschwebende Stimmung Dies ist die Stimmung, die von fast allen modernen Tasteninstrumenten ver- wendet wird. Bei dieser Stimmung ist jeder Halbton gleich weit vom nchs- ten entfernt, was kontantes Spiel in jeder Tonart erlaubt.

1. Vergewissern Sie sich, dass die [SONG]-LED nicht leuchtet, und drcken Sie [FUNC.]. Die [FUNC.]-LED leuchtet.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay ScL erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Stimmung. (Die Voreinstellung lautet 00.)

3. Whlen Sie mit [] oder [] die gewnschte Einstellung aus.

4. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die [FUNC.]-LED erlischt.

Diese Einstellung wird auf die Standardeinstellung (gleichmig temperi- erte Stimmung) zurckgesetzt, wenn Sie die Soundauswahl ndern und das Gert ausschalten.

Die Sounds Piano 1 und Piano 2 verwenden sogenanntes Stretched Tun- ing. Im vergleich zur gleichschwebenden Stimmung wird beim Stretched Tuning die Tonlage der niedrigen Noten leicht gesenkt und die Tonlage der hohen Noten leicht angehoben, um eine natrlich wirkende Resonanz zu erzielen.

Einstellen der Helligkeit des Sounds (Brillanz) Mit dieser Funktion regeln Sie die Helligkeit des Sounds.

1. Vergewissern Sie sich, dass die [SONG]-LED nicht leuchtet, und drcken Sie [FUNC.]. Die [FUNC.]-LED leuchtet.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay brL erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Helligkeitseinstellung. (Die Voreinstellung lautet 02.)

3. Whlen Sie mit [] oder [] die gewnschte Einstellung aus.

4. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die Einstellung wurde gespeichert, und die [FUNC.]-LED erlischt.

Diese Einstellung wird auch nach dem Ausschalten beibehalten. Durch Drcken von [FUNC.] nach dem ndern der Einstellung speichert das HT- 70 den neuen Wert automatisch im nichtchtigen Speicher. Das Multidis- play signalisiert, wenn ein Speichervorgang stattndet.

Display 15.0 ... 39.5 40.0 40.5 ... 65.0

Tonhhe (Hz) 415,0 ... 439,5 440,0 440,5 ... 465,0

Display 00 01 02

Einstellung Gleichschwebende Stimmung

Werckmeister Kirnberger

Display 01 02 03

Einstellung Milder Sound mit verrin- gerter Helligkeit

No r ma le Helligkeit

He l l e r Sound

6

Schalten Sie whrend des Speicherns das HT-70 nicht aus. Hierdurch kn- nen gespeicherte Einstellungen und Songdaten verloren gehen oder bes- chdigt werden.

Anpassen der Tastaturempndlichkeit Sie knnen die Art einstellen, in der die Klangdynamik auf die Strke des Spiels anspricht. Dies wird als Touch-Control-Funktion bezeichnet. Beim Einschalten des Gerts ist die normale Touch-Einstellung (02) gewhlt. 1. Drcken Sie die [FUNC.]-Taste zirka eine Sekunde lang.

Die [FUNC.]-LED Blinkt.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay tch erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Empndlichkeitseinstellung. (Die Voreinstellung lautet 02.)

3. Whlen Sie mit [] oder [] die gewnschte Einstellung aus.

4. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die Einstellung wurde gespeichert, und die [FUNC.]-LED erlischt.

Beim Ausschalten des Gerts wird diese Einstellung auf den Wert 02 zurckgesetzt.

Andern der Tonart (Transponieren) Durch Andern der Tonart des HT-70 (Transponieren) knnen Sie mit einem anderen Instrument oder Vokalen zusammen spielen und eine leichtere Tonart verwenden (z.B. eine mit weniger schwarzen Tasten) oder die Tonlage, in der Sie den Song gelernt haben. Dies wird als Transponier-Funktion bezeichnet. Sie knnen die Tonlage ber einen Bereich von elf Halbtnen transponieren.

1. Drcken Sie die [FUNC.]-Taste zirka eine Sekunde lang. Die [FUNC.]-LED Blinkt.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay trS erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Einstellung. (Die Voreinstellung lautet 00.)

3. Whlen Sie mit [] oder [] die gewnschte Einstellung aus.

4. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die [FUNC.]-LED erlischt.

Beim Ausschalten des Gerts wird diese Einstellung auf den Wert 00 zurckgesetzt.

Um den Song einen Halbton hher zu spielen Sie wollen die C

-Tonlage erklingen lassen, wenn Sie die C-Tonart spielen.

Stellen Sie die Tonart auf C (01 auf dem Multidisplay).

Ergebnis: Beim Spielen der Noten links, klingen auf dem HT-70 die Noten rechts.

Der Song ist in der Tonart B, aber sie wollen ihn mit Fingering in der Tonart G spielen

Die Tonlage von B ist eine kleine Terz (drei Halbtne) ber G. Das bedeutet, dass Sie die Tonlage D

(drei Halbtne hher) erklingen lassen wollen, wenn

Sie die C-Taste drcken. Stellen Sie die Tonart auf D

(03 auf dem Multidisplay).

Zurckstellen auf werkseitige Einstellungen Wenn sie Sounds gewhlt haben und ihre Einstellungen gendert haben, aber das HT-70 auf werkseitige Einstellungen zurcksetzen wollen, verfahren Sie wie folgt. Dieses Verfahren lscht nicht die aufgenommenen Spieldaten, aber stellt alle anderen Einstellungen auf ihre werkseitigen Vorgaben zurck. Wenn Sie die auf- genommenen Spieldaten lschen wollen, Siehe " Lschen eines Songs" auf Seite 64.

Bevor Sie fortfahren stellen Sie sicher, dass Sie wirklich die werkseitigen Vorgaben wiederherstellen wollen.

1. Schalten Sie das Gert aus.

2. Drcken Sie die [ ]-Taste, whrend Sie das Gert einschalten. Auf dem Multidisplay erscheint LFd, und alle Einstellungen wer den auf die Standardwerte zurckgesetzt.

Display 01 02 03

Touch-Con- trol-Einstel- lung

Leicht (auch leichtes Spiel kann laute Klnge erzeugen)

Normal (die Piano- Berhrung eines typischen Klaviers)

Schwer (Sie mssen stark spielen, um laute Klnge zu erzeugen)

Display -11 ... -03 -02 -01 00 01 02 03 ... 11

Tonlage C ... A A B C C D D ... B

67

6

MIDI Was bedeutet MIDI? MIDI (Musical Instrument Digital Interface, Digitale Schnittstelle fr Musikin- strumente) ist ein weltweit verbreiteter Standard zum Austausch von Spieldaten zwischen elektronischen Musikinstrumenten und Computern. Sie knnen das HT-70 verwenden, um andere mit MIDI ausgestattete Instru- mente zu spielen. Wenn Sie das tun, werden Ihre Sound-Wahlen und Halte- pedal-Bettigungen usw. ebenfalls als Steuerdaten bertragen. Sie knnen auch ein anderes MIDI-Keyboard oder einen Sequenzer (automatis- ches Wiedergabegert) zur Steuerung des HT-70 und Bedienung seines internen Tongenerators verwenden. Durch Kombination mehrere MIDI-Instrumente kn- nen Sie auch komplizierte Ensembles einrichten. Sie knnen die Recor derdaten des HT-70 ber MIDI auf einem externen Speichergert speichern. In diesem Kapitel werden die MIDI-bezogenenen Bedienvorgnge und Funk- tionen des HT-70 erklrt. Wenn Sie mehr ber MIDI wissen wollen, sollten Sie eines der zahlreichen Einfhrungsbcher ber dieses Thema lesen.

Herstellen von MIDI-Verbindungen Im Fachhandel erhltliche MIDI-Kabel dienen zur bertragung von MIDI- Daten. Verbinden Sie mit diesen Kabeln die MIDI-Anschlsse am HT-70 mit den MIDI-Anschlssen des externen MIDI-Gerts, mit dem MIDI-Daten ausgetaus- cht werden sollen. Es gibt zwei Typen von MIDI-Anschlssen.

MIDI IN-Anschluss Dieser Anschluss empfngt MIDI-Meldungen. Der MIDI IN-Anschluss erlaubt es Ihnen, Sounds vom HT-70 von einem externen MIDI-Gert zu spielen (z.B. MIDI-Keyboard oder Sequenzer). Verwenden Sie ein MIDI-Kabel zum Verbinden des MIDI IN-Anschlusses des HT-70 mit dem MIDI OUT-Anschluss des externen MIDI-Gerts.

MIDI OUT-Anschluss Dieser Anschluss gibt MIDI-Meldungen aus. Der MIDI OUT-Anschluss erlaubt Steuerung eines externen MIDI-Gerts mit vom HT-70 ausgegebenen MIDI-Meldungen. Verwenden Sie ein MIDI-Kabel zum Verbinden des MIDI OUT-Anschlusses des HT-70 mit dem MIDI IN-Anschluss des externen MIDI-Gerts.

MIDI-Kanle Wenn Sie die Verbindungen hergestellt haben, stellen Sie das HT-70 auf den gle- ichen MIDI-Kanal wie das angeschlossene MIDI-Gert. Es gibt 16 MIDI-Kanle, nummeriert 1 16.

Beim Einschalten des Gerts wird die Kanaleinstellung auf den Wert C01 zurckgesetzt.

1. Drcken Sie die [FUNC.]-Taste zirka eine Sekunde lang. Die [FUNC.]-LED Blinkt.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay Ch erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Einstellung. (Die Voreinstellung lautet C01.).

3. Whlen Sie mit [] oder [] die gewnschte Einstellung aus.

4. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die [FUNC.]-LED erlischt.

Das HT-70 kann ber den ausgewhlten MIDI-Kanal eingehende MIDI-Daten aufzeichnen.

Verwendung des HT-70 als multitim- brales Soundmodul Wenn Sie das HT-70 einschalten, arbeitet sein interner Soundgenerator als 16- Part multitimbrales Soundmodul, das von einem externen MIDI-Gert gespielt werden kann.

1. Verwenden Sie ein MIDI-Kabel zum Verbinden von MIDI IN am HT-70 mit MIDI OUT am Sequenzer oder hnlichen Gert.

2. Empfangen Sie MIDI-Meldungen vom angeschlossenen Sequenzer usw. Einzelheiten zum bertragen von Daten vom angeschlossenen Sequenzer siehe Bedienungsanleitung des verwendeten Gerts.

Empfngt das HT-70 gemeinsam mit den Musikdaten Programmwechselbefe- hle, wird der Sound gem empfangener Programmnummern gendert, whrend das Spiel fortgesetzt wird. Dies ist jedoch nur mglich, wenn der Pro- grammwechsellter fr den entsprechenden MIDI-Kanal deaktiviert ist. Beachten Sie jedoch, dass der ausgewhlte MIDI-Kanal ( S.68) Program- mwechsel ignoriert.

Beim Einschalten des HT-70 wird die Filterung in den deaktivierten Zustand zurckgesetzt.

1. Drcken Sie die [FUNC.]-Taste zirka eine Sekunde lang. Die [FUNC.]-LED Blinkt.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay 16t erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Einstellung. (Die Voreinstellung lautet Ein.).

3. Whlen Sie mit [] oder [] die gewnschte Einstellung aus.

4. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die [FUNC.]-LED erlischt.

Mit dem Soundknopf kann der Sound nicht gendert werden, whrend das HT-70 externe MIDI-Daten abspielt. Der ausgewhlte MIDI-Kanal ist hierzu jedoch in der Lage (S.68).

Lokales Ein-/Aus-Schalten Sie sollten die Lokal-Einstellung des HT-70 auf off stellen, wenn Sie die Tasta- tur des akustischen Klaviers, an dem das HT-70 angeschlossen ist, nur ein externes mit MIDI verbundenes Soundmodul spielen soll und nicht den internen Soundgenerator des HT-70, oder um zu verhindern, dass Duplikatno- ten erklingen, wenn Sie das HT-70 an einen Sequenzer angeschlossen haben, der die angelegten Daten zurck zum HT-70 reektiert (zurcksendet). Normalerweise lassen Sie die Lokal-Einstellung des HT-70 auf on, so dass es Sound produziert, wenn Sie die Tastatur spielen.

Beim Einschalten wird die Lokal-Einstellung automatisch eingeschaltet.

1. Drcken Sie die [FUNC.]-Taste zirka eine Sekunde lang. Die [FUNC.]-LED Blinkt.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay L.ct erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Einstellung. (Die Voreinstellung lautet Ein.)

3. Whlen Sie mit [] oder [] die gewnschte Einstellung aus.

4. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die [FUNC.]-LED erlischt.

Display C01 ... C16

Kanle 1 ... 16

Display on oFF

multitimbrales Ein Aus

Display on oFF

Local Ein Aus

8

Programmnderungen Diese Meldungen knnen vom HT-70 ausgegeben werden, um Programmnum- mern in einem externen MIDI-Gert zu whlen, oder von einem angeschloss- enen MIDI-Gert empfangen werden, um Programmnummern am HT-70 umzuschalten.

Ausgben von Programmnderungen Programmnummern an einem angeschlossen externen MIDI-Gert knnen vom HT-70 umgeschaltet werden.

Wenn Sie mit dem Soundknopf den Sound ndern, sendet das HT-70 die entsprechende Programmwechselnummer. Die Zuordnung entnehmen Sie bitte der Tabelle im nchsten Abschnitt.

Empfang von Programmnderungen Wenn das HT-70 eine Programmnderungsnummer von einem externen Gert empfngt, ndert sein multitimbraler Soundgenerator Programme, wie in der Tabelle unten gezeigt. Beachten Sie jedoch, dass der ausgewhlte MIDI-Kanal ( S.68) Program- mwechsel ignoriert. Das HT-70 ndert Sounds gem empfangener Programmwechselnummern wie in der folgenden Tabelle angegeben. Empfngt das HT-70 von einem MIDI- Gert eine Programmwechselnummer, die nicht in folgender Liste enthalten ist, generiert das HT-70 keinen MIDI-Sound mehr.

Programmwechsellter Aktivieren Sie den Filter, wenn Sie Programmwechselinformationen weder senden noch empfangen mchten. Deaktivieren Sie den Filter, um die bertra- gung dieser Informationen zu ermglichen.

Beim Einschalten wird der Filter fr alle MIDI-Kanle deaktiviert.

1. Drcken Sie die [FUNC.]-Taste zirka eine Sekunde lang. Die [FUNC.]-LED Blinkt.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay PC erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Einstellung. (Die Voreinstellung lautet Aus.)

3. Whlen Sie mit [] oder [] die gewnschte Einstellung aus.

4. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die [FUNC.]-LED erlischt.

Control-Change-Filter Control-Change-Befehle regeln den Betrieb von Controllern wie beispielsweise ein Haltpedal. Externe MIDI-Gerte steuern mit diesen Befehlen den Betrieb des HT-70, und das HT-70 steuert mit diesen Befehlen den Betrieb externer MIDI- Gerte.

Deaktivieren Sie den Filter, wenn Sie Control-Change-Befehle senden und emp- fangen mchten. Aktivieren Sie den Filter, um die bertragung dieser Informa- tionen zu unterbinden.

Beim Einschalten wird der Filter fr alle MIDI-Kanle deaktiviert.

1. Drcken Sie die [FUNC.]-Taste zirka eine Sekunde lang. Die [FUNC.]-LED Blinkt.

2. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay CC erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Einstellung. (Die Voreinstellung lautet Aus.)

3. Whlen Sie mit [] oder [] die gewnschte Einstellung aus.

4. Drcken Sie noch einmal [FUNC.], um den Einstellvorgang abzuschlieen. Die [FUNC.]-LED erlischt.

Einzeln Bank# PC# Sound

00 00 PIANO1

01 00 PIANO2

00 04 E.PIANO1

00 05 E.PIANO2

00 06 HARPSI.

00 19 P.ORGAN

00 16 E.ORGAN

00 48 STRINGS

Display on oFF

Programmwechsellter Ein Aus

Display on oFF

Control-Change-Filter Ein Aus

69

7

USB Einsatz von MIDI ber eine USB- Verbindung Das HT-70 ermglicht die MIDI-Kommunikation mit einem Computer dir ekt ber eine USB-Verbindung. Sie brauchen also weder ein MIDI-Kabel noch eine MIDI-Schnittstelle, um MIDI-Daten zu bertragen. Nach dem Herstellen der Verbindung knnen Sie das HT-70 beispielsweise als MIDI-Sound-Generator oder MIDI-Keyboard verwenden.

Anschluss am Computer Verwenden Sie, wenn mglich, den KORG USB-MIDI Driver, um die Verbind- ung zu einem Computer mittels USB herzustellen. Verwenden Sie den Treiber insbesondere, wenn der Computer ber die entsprechende Untersttzung ver- fgt.

Folgende Computerumgebungen untersttzen den KORG USB-MIDI Driver. Windows:

Computer: Voraussetzung sind ein USB-Port und Microsoft Windows XP oder Microsoft Windows Vista.

Betriebssystem: Microsoft Windows XP/Vista (Hinweis: Der Korg USB-MIDI Driver x64 ist nur als Betaversion erhltlich.)

Macintosh: Computer: Apple Macintosh mit integriertem USB-Port und Mac OS X.

Betriebssystem: Mac OS X 10.3 oder hher

Auch wenn die oben genannten Voraussetzungen erfllt werden, ist das keine Garantie dafr, dass der Computer mit dem HT-70 tatschlich funk- tioniert. Einige Computer sind zu diesem Zweck nicht geeignet, obwohl die oben genannten Voraussetzungen erfllt werden.

Beachten Sie vor der Verwendung Folgendes Korg Inc. besitzt das Urheberrecht fr die gesamte mit diesem Produkt gelieferte Software. Eine Lizenzvereinbarung fr die Software wird separat bereitgestellt. Lesen Sie die Lizenz, bevor Sie diese Software installieren. Durch die Installation dieser Software erklren Sie sich mit dieser Vereinbarung einverstanden.

Windows XP and Vista: Installation des KORG USB-MIDI Driver Schlieen Sie das HT-70 erst dann mit dem USB-Kabel am Computer an, nach- dem Sie die KORG USB-MIDI Driver Tools installiert haben.

Verfahren Sie folgendermaen.

1. Legen Sie die beigefgte CD-ROM ins CD-ROM-Laufwerk des Computers ein. In den meisten Fllen startet das Installationsprogramm der KORG Digital Piano Application beim Einlegen der CD-ROM automatisch. Ist auf Ihr em Computer der automatische Start deaktiviert, starten Sie das Pr ogramm direkt auf der CD-ROM, indem Sie auf Korg- Setup.exe doppelklicken.

2. Folgen Sie den Anweisungen auf dem Bildschirm.

Das Installationsprogramm installiert auch den KORG MIDI Data Filer. Der Data Filer wird nicht vom HT-70 verwendet.

3. Schalten Sie das HT-70 aus, und verbinden Sie das HT-70 mittels USB- Kabel mit dem Computer. Der Computer installier t automatisch den stan- dardmigen Windows-USB-MIDI-Treiber. Jetzt mssen Sie den KORG USB-MIDI Driver fr den verwendeten USB- Port installieren.

Installation des KORG USB-MIDI Driver fr Windows 1. Installieren Sie die KORG USB-MIDI Driver Tools wie oben beschrieben.

2. Starten Sie den Computer neu, schalten Sie das HT-70 ein, und verbinden Sie den Computer und das HT-70 mittels USB-Kabel.

Der KORG-USB-MIDI-Treiber muss fr jeden verwendeten USB-Port separat installiert werden. Wenn Sie das HT-70 zu einem spteren Zeit- punkt an einem anderen USB-Port anschlieen mchten, mssen Sie diesen Vorgang zum Installieren des Treibers fr den neuen Port wied- erholen.

3. Whlen Sie folgende Optionen, um die Installationsanweisungen zu ffnen: Start Alle Programme KORG KORG USB-MIDI Dr iver Tools Installation Manual.

4. Folgen Sie den Anweisungen zur Installation, um den Treiber zu installieren.

Treiberports Keyboard-Port: Wird von der Computeranwendung fr den Empfang von MIDI-Befehlen vom HT-70 verwendet (Keyboard- und Controller-Daten). Sound-Port: Wird von der Computeranwendung zum Senden von MIDI-Befehlen ver - wendet, die fr die Erzeugung von Tnen mit dem internen Tongenerator des HT-70 bestimmt sind.

Mac OS X: Installation des KORG USB-MIDI Driver Verwenden Sie, wenn mglich, den KORG USB-MIDI Driver zum Her - stellen einer Verbindung zu einem Computer mittels USB. Verwenden Sie den Treiber insbesondere, wenn der Computer ber die entsprechende Untersttzung verfgt.

Installation des KORG USB-MIDI Driver 1. Legen Sie die beigefgte CD-ROM ins CD-ROM-Laufwerk des Computers

ein.

2. ffnen Sie auf der CD-ROM den Ordner KORG USB-MIDI Driver, und dop- pelklicken Sie auf KORG USB-MIDI Driver.pkg, um das Installationspro- gramm zu starten. Folgen Sie den Anweisungen auf dem Bildschirm.

Treiberports Keyboard-Port: Wird von der Computeranwendung fr den Empfang von MIDI-Befehlen vom HT-70 verwendet (Keyboard- und Controller-Daten). Sound-Port: Wird von der Computeranwendung zum Senden von MIDI-Befehlen ver - wendet, die fr die Erzeugung von Tnen mit dem internen Tongenerator des HT-70 bestimmt sind.

0

USB-Modus Das HT-70 untersttzt die bertragung von Daten zwischen dem internen Spe- icher und einem externen Computer. Die efzienteste Methode fr diese ber- tragung ist eine USB-Verbindung. Diese Fhigkeit wird von Windows ME, Windows 2000 und allen nachfolgenden Windows-Versionen und von Mac ab OS 9.0.4 untersttzt.

Schlieen Sie alle MIDI-Anwendungen auf dem Computer, bevor Sie den USB-Modus aktivieren, um Daten vom oder zum HT-70 zu bertragen. Wird whrend der USB-bertragung eine MIDI-Anwendung ausgefhrt, knnen auf dem HT-70 Daten beschdigt werden.

Das HT-70 wird beim Beenden des USB-Modus (indem Sie auf dem HT-70 den Modus auf oFF setzen, das USB-Kabel aus dem HT-70 ziehen, das USB-Kabel aus dem Computer ziehen usw.) automatisch neu gestartet. Dies bedeutet, dass alle nicht gespeicherten Daten und Einstellungen ver - loren gehen. Speichern Sie deshalb vor dem Aktivieren des USB-Modus alle Daten und Einstellungen.

Die USB-Verbindung kann nicht fr die MIDI-Kommunikation verwendet werden, solange im USB-Modus Daten bertragen werden.

1. Verbinden Sie das HT-70 und den Computer mit einem USB-Kabel.

2. Drcken Sie die [FUNC.]-Taste zirka eine Sekunde lang. Die [FUNC.]-LED Blinkt.

3. Drcken Sie mehrmals die [DISPLAY]-Taste, bis auf dem Multidisplay USb erscheint. Nach dem Loslassen der Taste erscheint auf dem Multidisplay die aktuelle Einstellung. (Beim Einschalten ist der USB-Modus auf oFF gesetzt.)

Bei aktiviertem USB-Modus sind die meisten anderen Anwendungen deaktiviert. Nur die folgenden Vorgnge sind mglich: Ausschalten des USB-Modus, Aktivieren/Deaktivieren des Halls, Ein-/Ausschalten des Metronoms und das Spielen von Noten auf dem Keyboard.

4. ndern Sie mit [] oder [] die Einstellung.

Das HT-70 wird automatisch neu gestartet, wenn Sie den USB-MODUS ausschalten.

Wenn Sie den USB-Modus whrend der Datenbertragung mittels USB beenden (indem Sie auf dem HT-70 den USB-Modus deaktivieren, das USB-Kabel herausziehen usw.) knnen auf dem HT-70 oder auf dem Computer Daten beschdigt werden.

Schalten Sie bei aktivierten USB-Modus das HT-70 nicht aus. Beim Ausschalten werden u. U. auf dem HT-70 oder auf dem Computer Daten beschdigt.

5. Nach dem Aktivieren des USB-Modus knnen Sie das HT-70 so wie jedes andere externe USB-Laufwerk verwenden. Sie knnen darauf Dateien able- gen oder lschen und Ihre Daten sichern und wiederherstellen. HT-70-Daten werden im Ordner KORG USER in Unterordnern gespe- ichert. Die Namen der Dateien in diesen Ordnern knnen bis zu 128 Zeichen lang sein.

6. Nach Abschluss der Datenbertragung entfernen Sie das USB-Laufwerk vom Computerdesktop. Informationen hierzu nden Sie in der Bedienung- sanleitung des Computers. Bei Verwendung von Windows XP: Beim Entfernen des USB-Laufwerks kehrt das HT-70 automatisch zur Startanzeige zurck. (Bei Verwendung von Windows Vista mssen Sie nach dem Entfernen des USB-Laufwerks am Computer die Taste am HT-70 drcken, um zur Startanzeige zurckzuke- hren. Bei Verwendung eines Mac-Betriebssystems: Wenn Sie KORG SSD in den Papierkorb ziehen (oder KORG SSD entfernen), kehrt das HT-70 automa- tisch zur Startanzeige zurck.

Abspielen von MIDI-Dateien

Das HT-70 erkennt und spielt im Ordner UserSong gespeicherte Songs, vorausgesetzt, diese Songs sind im Standard-MIDI-Format gespeichert, und der Dateiname besteht aus einem U und zwei Ziffern (01 bis 99) sowie der Erweiterung .mid.

Beispiele: U07.mid, U34.mid

Das HT-70 spielt Standard-MIDI-Dateien womglich nicht korrekt ab, wenn diese in einer Taktart aufgenommen wurden, die mit dem HT-70 nicht festgelegt werden kann.

Display on oFF

USB-Modus ON (Massenspeicher) OFF (USB-MIDI)

Ordner inhalt

GLOBAL Globale (allgemeine) Einstellungen

PRESET Sound-Presets

UserSong Auf dem HT-70 aufgenommene Songs und Songs, die mit externen Sequencern erstellt wurden. In diesen Ordner knnen alle Songs im Standard-MIDI-Format (Dateierweit- erung MID) kopiert werden.

71

7

Anhang Strungssuche

Gert schaltet nicht ein

Ist der Gleichstromstecker des Netzteils an der Buchse DC12V des HT-70 angeschlossen?

Ist das Netzkabel des Netzteils an einer Netzsteckdose mit der richtigen Netzspannung angeschlossen?

Ist das Gert eingeschaltet? (S.56)

Wenn das Gert immer noch nicht einschaltet, ziehen Sie das Netzteilka- bel von der Steckdose ab und wenden sich an den Kundendienst.

Kein Ton

Ist mglicherweise der [VOLUME]-Knopf des HT-70 ganz nach links gedreht (bis kurz vor der OFF-Stellung)? (S.56)

Ist der gewhlte Part auf Wiedergabe gestellt? (S.65)

Wurden Spieldaten fr den gewhlten Part aufgenommen? (S.63 )

Ist mglicherweise der gewhlte Part stummgeschaltet? (S.65)

Stellen Sie sicher, dass die Lokal-Einstellung auf ON steht (S.68).

Was bedeutet die Fehlermeldung E01 auf dem Multidisplay? Diese Fehlermeldung bedeutet, dass die Kabelverbindung zwischen dem Piano und dem HT-70 fehlerhaft ist. Kontaktieren Sie einen quali- zierten Techniker oder Fachhndler. Drcken Sie die Taste [] oder [], um die Fehleranzeige E01 auszublenden.

Erscheint die Fehlermeldung E04 auf dem Multidisplay? Wenn ja, kontaktieren Sie einen qualizierten Techniker oder Fachhn- dler. Drcken Sie die Taste [] oder [], um die Fehleranzeige E04 auszublenden.

Wenn das Multi-Display E02 azeigt

Die Installationsdaten fr das Gert sind verlorengegangen, so dass die Vorgabedaten eingelesen wurden. Sie knnen weiter auf dem HT-70 spielen, aber Lautstrke, Tnlage und Pedalbettigung knnen ungenau sein. Bitte wenden Sie sich an einen qualizierten Installationstechniker zur Wartung und Neueinstellung. Drcken Sie die Taste [] oder [], um die Fehleranzeige E02 aus- zublenden.

Noten sind unterbrochen

Das HT-70 ist darauf ausgelegt, den zuletzt gespielten Noten Prioritt zu geben, so dass bei berschreitung der maximalen Polyphonie vorher gespielte Noten verschwinden knnen. Die maximale Polyphonie fr den Sound E.Piano 1 betrgt 80 Noten. Da die anderen Sounds doppelt so viele Daten fr jede Note bentigen, ist ihre maximale Polyphonie 40 Noten. Wenn Sie das Haltepedal verwenden oder aufgenommene Daten abspielen, beachten Sie immer die maximale Polyphonie und whlen Sie den geeigneten Sound fr Ihre Situation.

Die Tonlage oder der Ton des Klavies klingt in manchen Tonalregionen falsch

Die Piano-Sounds des HT-70 replizieren den Sound eines echten Klaviers so treu wie mglich. Das bedeutet, dass in manchen Regionen der Tasta- tur das Gefhl entstehen kan, dass die Obertne strker erscheinen oder Ton oder Tonlage falsch wirkt. Dies ist keine Fehlfunktion.

Eine bestimmte Taste klingt nicht, ist zu laut oder zu weich

Die Pedalbettigung ist unzureichend oder zu stark

Die Tonlage ist anders als beim akustischen Klavier

Erscheint die Fehlermeldung E03 auf dem Multidisplay? Wenn ja, wurde das HT-70 nicht kalibriert. Kontaktieren Sie einen quali- zierten Techniker oder Fachhndler.

Erzeugt eine bestimmte Taste keinen Ton, einen zu lauten oder zu leisen Ton, ist womglich die Kalibrierung fehlerhaft. Kontaktieren Sie einen qualizierten Techniker oder Fachhndler.

Dieses Problem kann durch die Dmpfungsfunktion verursacht werden, wenn diese nicht regelmig von einem qualizierten Techniker gewartet und eingestellt wird. Wir empfehlen, das Klavier einmal jhr- lich stimmen und einstellen zu lassen.

Das Keyboard erzeugt keinen Ton, wenn es als Piano gespielt wird. (falls es ber eine automatische Stummschaltfunktion verfgt)

Leuchtet die Muting-Bar-LED auf der Pianounterseite? (S.55)

Mglicherweise klemmt die elektrisch betriebene Dmpfvorrichtung. Zur berbrckung knnen Sie den Dmpfer mit dem Auslsehaken, der mit dem Instrument mitgeliefert wurde, lockern.

Wenden Sie sich anschlieend an einen qualizierten Techniker oder einen Fachhndler.

Kann nicht aufnehmen

Ist genug freier Platz auf dem Recorder vorhanden? (S.64, S.73)

Wenn ich von der Mitte einer Aufnahme an neu aufnehmen will ist Tempo der Taktma fr den aufgenommenen Teil anders.

Wurde bei der Neuaufnahme das Tempo und Taktma genau so eingest- ellt wie bei der vorherigen Aufnahme? Beim Aufnehmen ber vorhandene Songdaten kann das HT-70 zwar das Tempo, aber nicht die Taktart ndern. Beim Hinzufgen neuer Takte zu vorhandenen Songs kann das HT-70 allerdings sowohl die Taktart als auch das Tempo ndern (S.64).

Wiedergabe der aufgenommenen Par ts 1 und 2 mit getrenntem Tempo oder Taktma ist unmglich.

Beim HT-70 teilen sich Parts 1 und 2 das gleiche Tempo und Taktma. Die Wiedergabe verwendet das Taktma des zuerst aufgenommenen Parts (S.64).

Mein externes Gert reagiert nicht auf bertragene MIDI- Daten.

Stellen Sie sicher, dass das MIDI-Kabel richtig angeschlossen ist (S.68 ).

Stellen Sie sicher, dass das HT-70 MIDI-Daten auf dem gleichen Kanal bertrgt, auf dem das externe Gert empfngt (S.68).

Dmpfer

Auslsehaken

Freie Position

Dmpfposition

2

73

Installieren des KORG USB-MIDI Treiber fr Windows (bei Verwendung von Windows) ist unmglich

Stellen Sie sicher, dass das USB-Kabel richtig angeschlossen ist.

Stellen Sie sicher, dass die CD-ROM richtig im CD-ROM-Laufwerk eingesetzt ist.

Ist mglicherweise die Linse des CD-Laufwerks verschmutzt? Verwenden Sie einen im Handel erhltlichen Linsenreiniger zur Reini- gung der Linse des CD-Laufwerks.

Versuchen Sie, von einem Netzwerk-CD-Laufwerk zu installieren? Der Treiber kann nicht von einem CD-Laufwerk ber ein Netzwerk installiert werden.

Stellen Sie sicher, dass USB auf Ihrem Computer verfgbar ist. Bei Windows gehen Sie zu [Systemsteuerung] [System] Register [Hardware] [Gertemanager] und prfen Sie, ob Universal Serial Bus Controller und USB Root Hub vorhanden ist.

Wurde das HT-70 als unbekanntes Gert erkannt? Bei Windows gehen Sie zu [Systemsteuerung] [System] Regis- ter [Hardware] [Gertemanager] und prfen Sie dies. Wenn das HT-70 nicht richtig erkannt wurde, erscheint es als Anderes USB- Gert oder Unbekanntes Gert. Schlieen Sie das USB-Kabel erneut an, und wenn das HT-70 erneut als Unbekanntes Gert erscheint, wurde es als unbekanntes Gert erkannt. Lschen Sie den Eintrag fr Unbekanntes Gert, und installieren Sie den Treiber neu (S.70).

Software reagiert nicht

Stellen Sie sicher, dass das USB-Kabel richtig angeschlossen ist (S.71).

Haben Sie den Treiber installiert?

Stellen Sie sicher, dass der Computer, an dem das HT-70 angeschlossen ist, dieses richtig erkennt. Bei Windows XP prfen Sie dies in der Sys- temsteuerung unter Sound und Audiogerte Eigenschaften Hard- ware. Bei Mac OS X gehen Sie zu Macintosh HD Anwendungen- Ordner Utility-Ordner Audio-MIDI-Einstellungen, whlen das Register MIDI-Gerte und prfen, ob das HT-70 erscheint. Je nach der Hardware des verwendeten Computers kann es unmglich fr das HT-70 sein, ber einen USB-Anschluss erkannt zu werden.

Prfen Sie die Zuweisungen des HT-70 und der USB MIDI-Ports (S.70).

Es kann sein, dass das angeschlossene Gert oder die Software eine Funk- tionalitt von HT-70 nicht untersttzt. Siehe Dokumentation der verwen- deten Software bzw. Bedienungsanleitung des angeschlossenen Gerts.

Verwendung des HT-70 ohne Stummschaltung des angeschloss- enen Klaviers Das HT-70 ist darauf ausgelegt, Stummschaltung des Sounds des akustischen Klaviers zu ermglichen, so dass Sie mit Kopfhrern spielen und ben knnen, aber Sie knnen Teile der Funktionalitt des HT-70 ohne Stummschaltung des akustischen Klaviers verwenden.

ben Sie auf dem akustischen Klavier, whrend Sie das Metronom oder einen Piano-Song hren. Wenn Sie Ihr Tastaturspiel nicht von den Lautsprechern hren wollen, schalten Sie die Lokal-Einstellung auf off. (Schlagen Sie nach unter Lokales Ein-/Aus-Schalten auf Seite 68.)

Hier sind einige der Mglichkeiten:

Spielen Sie das akustische Klavier zusammen (berlagert) mit den Sounds des HT-70.

Da die MIDI-Meldungen des HT-70 bertragen werden, auch wenn Sie das akustische Klavier nicht stummschalten, knnen Sie MIDI-Meldun- gen whrend des Spiels des akustischen Klaviers fr mit anderen MIDI- Gerten verknpfte Auftritte bertragen.

Bei dem Modell mit Lautsprechern knnen die Sounds des HT-70 von den Lautsprechern ausgegeben werden. Es ist aber auch bei dem Modell ohne Lautsprecher mglich, handelsbliche Verstrkerlautsprecher an die Line-Aus- gangsbuchse anzuschlieen und das Instrument auf gleiche Weise zu spielen.

Fehlermeldungen Die meisten Fehlermeldungen erscheinen auf dem Multidisplay nur ein paar Sekunden lang. Bleibt eine Fehlermeldung (z. B. E05 oder E06) lnger angezeigt, knnen Sie sie durch Drcken von [] oder [] ausblenden.

E05 Die Aufnahme wurde automatisch beendet, da bereits 999 Takte des Songs aufgenommen wurden. Die 999 aufgenommenen Takte sind gespeichert.

E06 Die Aufnahme wurde automatisch beendet, da der Song bereits 45 000 Noten umfasst. Die 45.000 aufgenommenen Noten sind gespeichert.

E07 Der Benutzersongspeicher ist voll. Sie mssen erst fr freien Speicherplatz sorgen und nicht bentigte Songdaten lschen, um weitere Daten aufzuneh- men. Speichern Sie ggf. wichtige Songdateien auf einem Computer oder externen Speichergert, bevor Sie die Daten lschen.

E08 Die Aufnahme kann nicht ausgefhrt werden, da der Benutzersong nicht geladen wird. Dieser Fehler tritt nach Fehler E0b auf, wenn Sie aufzunehmen versuchen.

E09 Der Versuch, Parameter zu speichern oder Songdaten zu bearbeiten, ist fehlgeschlagen. Mglicherweise muss das HT-70 gewartet werden. Kontak- tieren Sie einen qualizierten Techniker oder Fachhndler.

E0A Der Song wurde auf dem Computer mit einem Schreibschutz versehen. Zum Bearbeiten des Songs auf dem HT-70 ndern Sie seinen Namen und speich- ern ihn als neuen Song.

E0b Die Songdatei ist zu gro oder nicht kompatibel. Beim Versuch aufzuneh- men, erscheint auf der Anzeige der Fehler E08.

E00...EFF Sensorfehler. Kontaktieren Sie einen qualizierten Techniker oder Fachhn- dler.

Technische Daten

* Anderungen des Designs und der technischen Daten ohne Vorankndigung bleiben im Sinne stndiger Verbesserungen vorbehalten.

Sound verarbeitet mit INFINITY

Sounds Acht Sounds: Piano 1, Piano 2, Electric piano 1, Electric piano 2, Harpsichord, Pipe organ, Electric organ, Strings

Soundgenerator Stereosampling-Soundgenerator

Maximale Polyphonie 80 noten

Effekte Reverb (drei Ebenen), Brilliance (drei Ebenen)

Recorder Zwei Parts, maximal 45.000 notenTempo/metro- nome, Record, Play/Pause, Stop, Part 1, Part 2

Keyboard-Modus Einzeln

Stimmungen Drei Typen (gleichschwebende Stimmung, Kirn- berger, Werckmeister)

Touch-Control Drei Ebenen (leicht, standard, schwer)

Bedienelemente [VOLUME] -Knopf, Sound-Wahlschalter, Schalter [SONG], [REVERB], [DISPLAY], [FUNC.], [], [], [ ], [], [], [ ], [PART 1], [PART 2]

Pedale *Halten, Sostenuto, *Soft *Halbpedalstellung wird untersttzt

Anschlsse Kopfhrer x 2, LINE OUT (Stereo), MIDI (IN, OUT), USB

Stromversorgung Gleichstrom 12 V (Netzteil mitgeliefert)

Abmessungen (B x T x H)

271 x 180 x 63 (mm) (nur Soundmodul)

Gewicht 1,4 Kg (nur Soundmodul)

Lieferumfang Netzteil, Kopfhrer, CD-ROM, externe Lautspre- cher (nur bei Modell mit Lautsprechern)

7

Feature List/Liste des fonctions/Funktionsliste

Metronome Functions ([ ] switch ashing)

General Functions #1 ([FUNC.] LED ON)

General Functions #2 ([Song] LED and [FUNC.] LED both ON)

General Functions #3([FUNC.] LED ashing: long press)

Switch Function Display Possible Settings [Default Setting]

Tempo 120 4...120...250 [120]

PART 1 Time signature 4 - 4(4/4) 1/2, 2/2, 1/4, 2/4, 3/4, 4/4, 6/8 [4/4]

PART 2 Level 100 0...127 [100]

Accent sound oFF / on1 / on2 None, Standard, Bell [oFF: None]

Metronome sound S1 / S2 Pendulum, Digital [S1: Pendulum]

[DISPLAY] Presses Required

Function Parameter/Value Possible Settings [Default Setting]

0 Copy a Recorded Song SAv / U01 U01...U99

1 Deleting a Song dEL / U01 U01...U99

2 Deleting a Part P.dL / ALL, P1, P2 Both parts, Part 1, Part 2

3 Pitch tUn / 40.0 415.0...440.0...465.0Hz 0.5Hz unit [440.0]

4 Temperament ScL / 00, 01, 02 Equal, Werckmeister, Kirnberger [00: Equal]

5 Brilliance brL / 01, 02, 03 Mellow, Normal, Brighter [02: Normal]

[DISPLAY] Presses Required

Function Parameter/Value Possible Settings [Default Setting]

0 Part mute level P.Lv / 30 0...90 [30]

1 AB Repeat on/off Ab.r / oFF on, off [oFF: off]

2 AB Repeat (start measure) A / 001 001...999 [001]

3 AB Repeat (end measure) b / 001 001...999 [001]

[DISPLAY] Presses Required

Function Parameter/Value Possible Settings [Default Setting]

0 Touch Control tch / 01, 02, 03 Light, Normal, Heavy [02: Normal]

1 Transpose trS / 00 -11...00...11 semitone [00]

2 MIDI channel Ch / C01 channel1...16 [C01]

3 Local on/off L.ct / on on, off [on: on]

4 Program change lter PC / oFF on, off [oFF: off]

5 Contorl change lter CC / oFF on, off [oFF: off]

6 Multi timbral on/off 16t / on on (Multi timbral), off (Single) [on: on]

7 USB mode USb / oFF on (Mass storage), off (USB MIDI) [oFF: off]

4

75

MIDI implementation chart

[Digital piano] HT-70 MIDI implementation chart

Function... Transmitted Recognized Remarks

Basic Channel:

Default Changed

Default Messages Altered

Mode:

Note Number: True Voice

Velocity: Note-on Note-off

Aftertouch: Polyphonic (Key) Monophonic (Channel)

Pitch Bender

Control Change

Program Change:

Exclusive:

Common: Song Position Song Select Tune

Realtime: Clock Command

Local On/Off All Notes Off Active Sense Reset

Aux Messages:

Notes:

1 116

1 116

0127

9n, V=1127

3

0127 0127

9n, V=1127

123125

*5

Mode 1: Omni On, Poly Mode 2: Omni On, Mono Mode 3: Omni Off, Poly Mode 4: Omni Off, Mono

: Yes : No

2008.11.21

Variable Range

0, 32 1 6

38 7

11 10

91, 93 64, 66, 67

65 5

71 72, 73

74 75, 76, 77, 78

98, 99 100, 101

120 121

*2, 3 *1, 2

*1, 2, 3 *1, 2, 3

*1, 2 *1, 2

*1, 2, 3 *2 *2

*1, 2 *1, 2, 3

*1, 2 *1, 2, 3

*1, 2 *1, 2, 3

*1, 2 *1, 2, 3 *1, 3, 4

*3, 4

Bank Select (MSB, LSB) Modulations Data Entry (MSB) Data Entry (LSB) Volume Expression Panpot Reverb Send, Chorus Send Damper, Sostenute, Soft Portament On/Off Portament Time Resonance EG Time (Release, Attack) Brightness Decay Time, Vibrato Rate, Depth, Delay NRPN (LSB, MSB) RPN (LSB, MSB) All sound off Reset all controllers

Receipt of range is different by sound

V=64

*1

*1

*1, 3, 4

For sending, the following values fully supported: 0, 4, 5, 6, 16, 19, 48. All other values can be sent only from onboard recorder data. Refer to Remarks

*1: Sends only data from the onboard recorder. *2: Sent and received only if MIDI filtering is off. *3: Selected MIDI channel will not receive or record. *4: Sent even if MIDI filtering is on. *5: Includes Inquires and GM Mode ON messages. GM Mode ON messages are received, but not all GM voices are supported. Channel 10 corresponds to the piano voice.

Cannot record. *1, 4

Manualsnet FAQs

If you want to find out how the HT-70 KORG works, you can view and download the KORG KHP-5000 HT-70 Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for KORG HT-70 as well as other KORG manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a KORG HT-70. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the KORG KHP-5000 HT-70 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This KORG KHP-5000 HT-70 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download KORG KHP-5000 HT-70 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print KORG KHP-5000 HT-70 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the KORG KHP-5000 HT-70 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.