Contents

KORG ARP ODYSSEY Module Owner's Manual PDF

1 of 92
1 of 92

Summary of Content for KORG ARP ODYSSEY Module Owner's Manual PDF

Module

M odule

IMPORTANT NOTICE TO CONSUMERS

This product has been manufactured according to strict specications and voltage requirements

that are applicable in the country in which it is intended that this product should be used. If you

have purchased this product via the internet, through mail order, and/or via a telephone sale, you

must verify that this product is intended to be used in the country in which you reside.

WARNING: Use of this product in any country other than that for which it is intended could be

dangerous and could invalidate the manufacturers or distributors warranty.

Please also retain your receipt as proof of purchase otherwise your product may be disqualied

from the manufacturers or distributors warranty.

Published 9/2016 Printed in China

- 3 -

O w

ne rs

m an

ua lThank you for purchasing the ARP ODYSSEY/ARP ODYSSEY ModuleDuophonic

synthesizer. To help you get the most out of your new instrument, please read this manual carefully.

Precautions Location Using the unit in the following locations can result in a malfunction. In direct sunlight Locations of extreme temperature or humidity Excessively dusty or dirty locations Locations of excessive vibration Close to magnetic fields

Power supply Please connect the designated AC adapter to an AC outlet of the correct voltage. Do not connect it to an AC outlet of voltage other than that for which your unit is intended.

Interference with other electrical devices Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions.

Handling To avoid breakage, do not apply excessive force to the switches or controls.

Care If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid cleaners such as benzene or thinner, or cleaning compounds or flammable polishes.

Keep this manual After reading this manual, please keep it for later reference.

Keeping foreign matter out of your equipment Never set any container with liquid in it near this equipment. If liquid gets into the equipment, it could cause a breakdown, fire, or electrical shock. Be careful not to let metal objects get into the equipment. If something does slip into the equipment, unplug the AC adapter from the wall outlet. Then contact your nearest Korg dealer or the store where the equipment was purchased.

* All product names and company names are the trademarks or registered trademarks of their respective owners.

DECLARATION OF CONFORMITY (for USA) Responsible Party : KORG USA INC. Address : 316 SOUTH SERVICE ROAD, MELVILLE, NY Telephone : 16313906500 Equipment Type : Duophonic synthesizer Model : ARPODYSSEY, ARPODYSSEYM This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation.

THE FCC REGULATION WARNING (for USA) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected. Consult the dealer or an experienced radio/TV technician for help. If items such as cables are included with this equipment, you must use those included items. Unauthorized changes or modification to this system can void the users authority to operate this equipment.

Notice regarding disposal (EU only) When this crossedout wheeled bin symbol is displayed on the product, owners manual, battery, or battery package, it signifies that when you wish to dispose of this product, manual, package or battery you must do so in an approved manner. Do not discard this product, manual, package or battery along with ordinary household waste. Disposing in the correct manner will prevent harm to human health and potential damage to the environment. Since the correct method of disposal will depend on the applicable laws and regulations in your locality, please

contact your local administrative body for details. If the battery contains heavy metals in excess of the regulated amount, a chemical symbol is displayed below the crossedout wheeled bin symbol on the battery or battery package.

ARP ODYSSEY ARP ODYSSEY Module

- 4 -

Introduction to the ODYSSEY

What is the ODYSSEY? The ODYSSEY was manufactured from 1972 through 1981 by the ARP Corporation, and was one of their bestknown products. Broadly speaking, there are three versions according to their date of production, and these three differ in appearance, as well as in tonal character and functionality. Model 2800 is known as Rev. 1; this includes the initial whitepanel model produced from 1972 to 1974 and the blackpanel model produced from 1974 to about 1975. Models 2810 2813 are known as Rev. 2; these consist of the blackpanel models which were produced from 1975 to about 1976. Changes were made to the filter, and changes were also made to the oscillator of some models. External audio input and CV/GATE input jacks were also added, and later models changed the knobstyle pitch bender to a PPC (Proportional Pitch Control). Models 2820 2823 are known as Rev. 3, and were produced from 1978 to about 1981. The panel changed to a black panel with orange silkscreening, and the design also changed significantly from models 2800 2813. The audio output was also changed from RCA/PHONE to XLR/PHONE jacks.

Main Features The traditional analog VCO, VCF, and VCA circuitry of the ARP ODYSSEY. This provides

the high degree of soundediting spontaneity that is uniquely offered by analog synthesis. 37note slimkey bed that covers a pitch range of seven octaves. [The ARP ODYSSEY

Module is a keyboardless model] You can play the instrument monophonically, or use duophonic mode that sounds the

oscillators at independent pitches when you play two keys simultaneously. (However, there is only one filter and one amp.)

Two types of envelope generators are provided: ADSR type and AR type. Oscillator sync. This feature is valued for generating numerous highfrequency overtones

and for its sharpness. The PPC (Proportional Pitch Control) using the original rubber pad has been reproduced. Modulation can be applied in a wide variety of ways. Two types of noise are provided. LFO and S&H are provided, and you can switch their routing. The filters from the three different types of ARP ODYSSEY are provided, and can be

selected by a single switch. Since an external audio input jack is provided, you can also process the sound of an

external musical instrument. A USB port and MIDI connectors are provided, allowing you to connect a PC or a MIDI

instrument.

Table of Contents

Introduction to the ODYSSEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 What is the ODYSSEY? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Panel description and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front panel (Noise type, Controller section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Front panel (VCO-1 section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Front panel (VCO-2 section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Front panel (LFO, SAMPLE AND HOLD section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Front panel (AUDIO MIXER, VCF, HPF, VCA section) . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Front panel (ENVELOPE GENERATOR section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Turning the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Turning the power off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Auto power-off function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Lets make some sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Basic settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

About MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Connecting MIDI devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Connecting a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 About the MIDI implementation chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

This manual explains the ARP ODYSSEY and the ARP ODYSSEY Module. Unless we specify otherwise, the panel illustrations are of the ARP ODYSSEY.

- 5 -

O w

ne rs

m an

ua lBlock diagram

NOISE GENERATOR

AUDIO MIXER

VOLTAGE CONTROLLED

FILTER

HIGH PASS

FILTER

VOLTAGE CONTROLLED

AMPLIFIER

RING MOD

SAMPLE AND

HOLD

SAMPLE AND HOLD

MIXER

VOLTAGE CONTROLLED OSCILLATORS

LOW FREQUENCY OSCILLATOR

PEDAL ADSR AND AR

ENVELOPE GENERATORS

TRIGGER

ARP ODYSSEY Module: Only MIDI IN

KEYBOARD

MIDI IN

ARP ODYSSEY: Built-in Keyboard and MIDI IN

ARP ODYSSEY ARP ODYSSEY Module

- 6 -

Panel description and functions

Front panel (Noise type, Controller section)

a

b c

d

e f g

a . NOISE GENERATOR switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [WHITE, PINK] Selects white noise or pink noise.

b . PORTAMENTO slider (black) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[MINMAX] Specifies how the portamento effect is applied (the time over which the pitch change occurs). If the slider is in the MIN position, no portamento effect is applied. As you move the slider toward the MAX position, the pitch change occurs over a longer time. If an optional (separately sold) pedal switch is connected to the PORTAMENTO FOOTSWITCH jack, it can be used to turn portamento on/off.

c . MODE switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[ON, OFF] Selects whether portamento is enabled when you use the TRANSPOSE lever. Use a finetipped pen or similar object to press this switch.

d . TRANSPOSE lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[2 OCTAVES UP, 0, 2 OCTAVES DOWN] Switches the range of pitches assigned to the keyboard in steps of two octaves.

e . PROPORTIONAL PITCH CONTROL - Pad The pitch is lowered according to how strongly you press the pad.

f . PROPORTIONAL PITCH CONTROL - Pad Vibrato is applied according to how strongly you press the pad.

g . PROPORTIONAL PITCH CONTROL - Pad The pitch is raised according to how strongly you press the pad.

- 7 -

O w

ne rs

m an

ua lFront panel (VCO-1 section)

c

d e f

h i j

g

a b

The following settings are for oscillator 1 (VCO1).

a . FREQUENCY COARSE slider (blue) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[20(0 .2)Hz2K(20)Hz] Rough pitch adjustment. This adjustment covers the range of 20 Hz 2 kHz if the keyboard switch is on, or 0.2 Hz 20 Hz if the keyboard switch is off.

The frequency range (20 Hz 2 kHz) is an approximate value.

b . FREQUENCY FINE slider (blue) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [400cent] Fine pitch adjustment.

c . Keyboard switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [AUDIO KYBD ON, LF KYBD OFF] If this is set to AUDIO KYBD ON, VCO1 is connected to the keyboard CV, and will produce pitches in the conventional way. If this is set to AUDIO KYBD OFF, VCO1 is disconnected from the keyboard CV, and will oscillate as an LFO. You can use this signal to modulate VCO2 or as an audio source for sound effects.

d . FM depth slider (pink) e . FM depth slider (yellow)

Adjusts the depth of FM (Frequency Modulation) when it is is applied.

f . PULSE WIDTH (WIDTH) slider (blue) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [50%MIN] Adjusts the pulse width.

g . PULSE WIDTH (MOD) slider (pink) Adjusts the depth of pulse width modulation.

h . FM source switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [LFO , LFO ] Selects the waveform of the modulation applied by the LFO.

i . FM source switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [S/H, ADSR ] Selects either Sample and Hold or the envelope generator (ADSR) as the modulation source.

j . Pulse width modulation souece switch . . . . . . . . . . . . . . . . . . . [LFO , ADSR ] Selects the source that will apply pulse width modulation.

ARP ODYSSEY ARP ODYSSEY Module

- 8 -

Front panel (VCO-2 section)

c

d e f

h i j

g

a b

The following settings are for oscillator 2 (VCO2).

a . FREQUENCY COARSE slider (green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[20(0 .2)Hz2K(20)Hz] Rough pitch adjustment. This is adjustable in the range of 20 Hz 2 kHz. If the SYNC switch is on, this changes the overtone structure rather than the pitch.

The frequency range (20 Hz 2 kHz) is an approximate value.

b . FREQUENCY FINE slider (green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [400cent] Fine pitch adjustment. If the SYNC switch is on, this changes the overtone structure rather than the pitch.

c . SYNC switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OFF, ON Turns sync on/off. If this is off, duophonic performance is possible. If this is on, VCO2 is synchronized with the frequency (pitch) of VCO1.

d . FM depth slider (pink)

e . FM depth slider (yellow) Adjusts the depth of FM (Frequency Modulation) when it is is applied.

f . PULSE WIDTH (WIDTH) slider (blue) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [50%MIN] Adjusts the pulse width.

g . PULSE WIDTH (MOD) slider (pink) Adjusts the depth of pulse width modulation.

h . FM source switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[LFO , S/H MIXER OR PEDAL] Selects either modulation by an LFO sine wave or modulation by the S/H MIXER (sample and hold mixer) or pedal signal. If you select S/H MIXER OR PEDAL, the modulation can be controlled by an optional (separately sold) volume pedal connected to the pedal jack.

i . FM source switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [S/H, ADSR ] Selects either Sample and Hold or the envelope generator (ADSR) as the modulation source.

j . Pulse width modulation souece switch . . . . . . . . . . . . . . . . . . . [LFO , ADSR ] Selects the source that will apply pulse width modulation.

- 9 -

O w

ne rs

m an

ua lFront panel (LFO, SAMPLE AND HOLD section)

a

b c d

e f g

a . LFO FREQ (LFO speed) slider (pink) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0 .2Hz20Hz] Adjusts the LFO speed. Raising the slider makes the speed faster.

b . S/H input level slider (blue) Adjusts the level at which the waveform output from VCO1 is input to the S/H MIXER.

c . S/H input level slider (white) Adjusts the level at which noise or the square wave output from VCO2 is input to the S/H MIXER.

d . S/H OUTPUT LAG slider (yellow) Smooths the changes of the S/H output voltage. As you move the slider toward the MAX position, a greater amount of the smoothing will be applied.

e . S/H input source switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [VCO-1 , VCO-1 ] Selects the source (VCO1 waveform) that is input to the S/H MIXER.

f . S/H input source switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[NOISE GEN, VCO-2 ] Selects the source (noise or VCO2 square wave) that is input to the S/H MIXER.

g . S/H trigger source switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[LFO TRIG, KYBD TRIG] Selects the signal (either the output of the LFO or the output of the keyboard) that is used as the trigger when detecting an audio signal sent from the S/H MIXER.

ARP ODYSSEY ARP ODYSSEY Module

- 10 -

Front panel (AUDIO MIXER, VCF, HPF, VCA section)

d e

f

c

a

g h i j

k l m

n

b

o p q r s t

a . VCF FREQ slider (black) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [16Hz16KHz] Adjusts how the LPF (Low Pass Filter) is applied. If the slider is in the lowest position (16 Hz), the highfrequency range of the input signal is cut, producing a soft sound. Raising the slider makes the sound brighter.

b . VCF RESONANCE slider (black) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[MINSELF OSC] Adjusts the resonance. This modifies the tonal character by boosting the overtones in the region of the cutoff point. As you raise the slider, selfoscillation (a state in which the VCF itself produces a sound) will occur starting at a certain point.

c . VCF TYPE switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[ , , ] Selects the type of VCF. : ODYSSEY Rev. 1 : ODYSSEY Rev. 2 : ODYSSEY Rev. 3

d . HPF CUTOFF FREQ slider (black) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [16Hz16KHz] Adjusts how the HPF (High Pass Filter) is applied. As you raise the slider, the lowfrequency region of the input signal is cut, producing a thinner sound. This is useful when you are simulating the sound of certain instruments.

e . DRIVE switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[OFF, ON] By turning this on you can make the VCA distort.

f . VCA GAIN slider (black) Adjusts the volume at which the audio signal always passes through the VCA.

g . NOISE/RING MOD slider (white) Adjusts the level of the audio signal that is sent from the noise generator or the ring modulator.

h . VCO-1 volume slider (blue) Adjusts the level of the audio signal that is sent from VCO1.

i . VCO-2 volume slider (green) Adjusts the level of the audio signal that is sent from VCO2.

j . Filter modulation level slider (black) Adjusts the level of the signal that controls the VCF FREQ, or adjusts how the signal sent from the S/H MIXER opens and closes the filter.

- 11 -

O w

ne rs

m an

ua lk . Filter modulation level slider (yellow)

Adjusts how the filter is opened and closed by S/H (sample and hold) or the LFO.

l . Filter modulation level slider (pink) Adjusts how the two envelope generators (AR and ADSR) control the filter.

m . VCA level slider (red) Adjusts the level at which the envelope generators (AR and ADSR) control the VCA. In practical terms, this is the master volume of the ARP ODYSSEY. If the DRIVE switch is on, this also adjusts the VCA distortion.

n . Filter input source (NOISE/RING MOD) switch . . . . . . . . . . . . . . . . . . [NOISE, RING MOD] Selects either noise or ring modulator.

o . Filter input source (VCO-1 wave) switch . . . . . . . . . . . .[VCO-1 , VCO-1 ] Selects the VCO1 waveform (sawtooth or square). If you select square wave, you can raise the PULSE WIDTH slider (page 7) to change from a square wave to a pulse wave.

p . Filter input source (VCO-2 wave) switch . . . . . . . . . . . .[VCO-2 , VCO-2 ] Selects the VCO2 waveform (sawtooth or square). If you select square wave, you can raise the PULSE WIDTH slider (page 8) to change from a square wave to a pulse wave.

q . Filter modulation source (KYBD CV/S/H MIXER OR PEDAL) switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[KYBD CV, S/H MIXER OR PEDAL] Selects the source that will control the filter. If you select KYBD CV (keyboard control voltage), the signal normally used to convey key information from the keyboard to the VCO can be used to open and close the filter. For example, you can produce an effect in which the filter opens more for higher notes. If you select S/H MIXER OR PEDAL, the signal sent from the S/H MIXER will open and close the filter. If an optional (separately sold) volume pedal is connected to the PEDAL jack, you can use the signal of the pedal to control the VCF, producing an effect like a wah pedal.

r . Filter modulation source (S/H/LFO) switch . . . . . . . . . . . . . . . . . . . . . . . . . . . .[S/H, LFO ] Selects the source that will control the filter. You can produce a wah effect by using the LFO to modulate the filter.

s . Filter modulation source (ADSR/AR) switch . . . . . . . . . . . . . . . .[ADSR , AR ] Selects the envelope generator that will control the filter.

t . VCA EG switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[AR , ADSR ] Selects the envelope generator that will control the VCA.

ARP ODYSSEY ARP ODYSSEY Module

- 12 -

Front panel (ENVELOPE GENERATOR section)

c

a

b

d e f

h i j

g

a . AR EG - ATTACK slider (red) Adjusts the attack time of the AR envelope generator.

b . AR EG - RELEASE slider (red) Adjusts the release time of the AR envelope generator.

c . Power LED This is lit if the power is on, and is unlit if the power is off. If the auto poweroff function is disabled, the LED blinks several times and then stays lit when you turn on the power.

d . ADSR EG - ATTACK slider (red) Adjusts the attack time of the ADSR envelope generator.

e . ADSR EG - DECAY slider (red) Adjusts the decay time of the ADSR envelope generator.

f . ADSR EG - SUSTAIN slider (red) Adjusts the sustain time of the ADSR envelope generator.

g . ADSR EG - RELEASE slider (red) Adjusts the release time of the ADSR envelope generator.

h . ADSR trigger source switch . . . . . . . . . . . . . . . . . . . . . . . . [KYBD GATE, LFO REPEAT ] Selects the trigger that is sent to the ADSR envelope generator. If KYBD GATE is selected, the trigger sent from the keyboard is sent to the EG. If LFO REPEAT is selected, the pulse wave of the LFO is sent to the EG, and the EG repeats the envelope cyclically at the rate of the LFO FREQ.

i . ADSR repeat switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [KYBD REPEAT, AUTO REPEAT] This is effective if LFO REPEAT is selected by the ADSR or by the AR trigger source switch. If KYBD REPEAT is selected, the LFO trigger sent repeatedly to the EG continues repeating only as long as the key is pressed. If AUTO REPEAT is selected, it continues repeating regardless of the keyboard on/off status.

j . AR trigger source switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [KYBD GATE, LFO REPEAT ] Selects the trigger that is sent to the AR envelope generator. This has the same function as the ADSR trigger switch.

- 13 -

O w

ne rs

m an

ua lRear panel

e f g h i j k l

m n o

b c da

onm

p

k le f g h i jb c da

ARP ODYSSEY Module

ARP ODYSSEY

a . Cable hook Wrap the AC adapter cable around this hook to prevent the AC adapter from being accidentally disconnected.

b . DC 9V jack Connect the included AC adapter here. First connect the AC adapter to this instrument, and then connect the plug to an AC outlet.

c . Power switch This turns the power on/off. To turn the power off, press and hold the switch.

d . MIDI IN connector You can connect an external MIDI device to this connector to receive MIDI data.

e . USB B port You can connect a computer to this port to transmit and receive MIDI data.

f . PEDAL jack Connect an optional (separately sold) volume pedal here. Youll also use this jack when connecting the SQ1 (sequencer) to control the ARP ODYSSEY.

g . PORTAMENTO FOOTSWITCH jack Connect an optional (separately sold) pedal switch here.

h . OUTPUT LOW jack Connect an amp or powered monitor speaker here.

i . OUTPUT HIGH jack Here you can connect a mixer or amp that is equipped with an XLR jack.

j . EXT AUDIO INPUT jack If youre using the ARP ODYSSEY as an effect processor, use a monaural phone cable to connect your external audio source to this jack. An external signal that is input to the EXT AUDIO INPUT jack is input to the AUDIO MIXER and passes through the VCF and VCA. Use the connected external device to adjust the volume.

Tip: If you use the included phone jack cable to connect the EXT AUDIO INPUT jack to the headphone jack, selffeedback can be applied, expanding the range of sounds. Use the headphone volume to adjust the amount of feedback.

k . Headphone volume Adjusts the volume of the connected headphones. If selffeedback is being applied, this adjusts the amount of feedback.

l . Headphones jack Connect your headphones here. This provides the same signal as the output from the OUTPUT LOW jack or OUTPUT HIGH jack. If you want to apply self feedback, connect this jack to the EXT AUDIO INPUT jack of the ARP ODYSSEY.

m . CV IN/OUT jacks These jacks input and output a control voltage (a voltage that indicates the pitch).

n . GATE IN/OUT jacks These jacks input and output a gate signal (a signal that sound is being produced).

o . TRIG IN/OUT jacks These jacks input and output a trigger (a signal that the keyboard is being pressed).

Tip: If you use the included miniphone cable to connect the TRIG IN jack and the GATE OUT jack, the ADSR EG will not be retriggered, allowing you to play legato.

p . MODE SWITCH (ARP ODYSSEY Module only) This switch lets you set the MIDI channel and the auto poweroff setting. When you operate the switch, the power LED blinks.

Phone cable (Included)

Mini-phone cable (Included)

ARP ODYSSEY ARP ODYSSEY Module

- 14 -

Getting started

Connections The following illustration shows an example of typical connections. Connect your equipment as appropriate for your needs.

to electrical outlet

AC adaptor (included)

Pedal switch

Monitor amplifier, etc.

XLR cable

USB cable

Computer

MIDI OUT

Headphones Volume pedal

To an external audio source, etc.

MIDI cable Mono phone cable

Mono phone cable

Mono phone cable

or

Other example connections You can use patch cables to connect the ARP ODYSSEY to a sequencer as shown below, so that the sequencer can control the ARP ODYSSEY to produce sound. If youre connecting the ARP ODYSSEY with the SQ1, connect the ARP ODYSSEY's PEDAL jack to the SQ1s CV OUT jack so that the ARP ODYSSEYs VCO 2 pitch and filter can be controlled.

Sequencer etc.

CV OUT

GATE OUT CV IN

GATE IN

CV OUT

Conversion plug

You must turn off the power of all devices before connecting anything. If you connect devices while the power is on, you might damage your speaker system or cause your equipment to malfunction or be damaged.

If you want to connect a pedal, use a monaural cable to connect the PEDAL jack of the ARP ODYSSEY to the OUT 1 or OUT 2 jack of an optional (separately sold) Korg VP10 volume pedal. In this case, the MINIMUM VOLUME of the VP10 must be set to 0 (minimized).

Tip: If you want to use a pedal switch to turn portamento on/off, connect an optional (separately sold) Korg PS1 or PS3 pedal switch to the PORTAMENTO FOOTSWITCH jack of the ARP ODYSSEY. Portamento turns off when you press the pedal switch; releasing the pedal switch applies the portamento effect at the time specified by the PORTAMENTO slider.

- 15 -

O w

ne rs

m an

ua lTurning the power on

Turn off the power of your powered monitor speakers or other external output device before you poweron the ARP ODYSSEY.

1. Lower the ARP ODYSSEYs VCA level slider (page 11) and VCA GAIN slider (page 10) to the minimum position.

2. Press the ARP ODYSSEYs power switch to turn the power on. The power LED will light up.

3. Lower the volume controls of your powered monitors or external output system, and then turn their power on.

4. Raise the volume controls of your powered monitors or external output system to an appropriate level, and adjust the ARP ODYSSEYs VCA level slider.

Tip: If you are not familiar with how to create sounds, we suggest that you now adjust the settings as described in the Basic settings section (page 16).

Turning the power off 1. Lower the volume of your powered monitors or external output system, and turn

their power off.

2. Hold down the ARP ODYSSEYs power switch, and release it when the power LED goes dark.

Auto power-off function The ARP ODYSSEY has an auto poweroff function that automatically turns the power off when approximately four hours have elapsed since the instrument was last played or used. With the factory settings, the auto poweroff function is enabled.

Changing the auto power-off setting If desired, you can enable or disable the auto poweroff function.

Do not turn off the power while you are changing this setting. Doing so may destroy data, causing a malfunction.

Tip: The setting of the auto poweroff function is remembered even after you turn off the power.

Disabling the auto power-off function

ARP ODYSSEY

1. While holding down the C3, D3, and E3 keys of the keyboard, press the power switch to turn the power on.

C3 D3 E3

2. When the power LED blinks several times and then remains lit, release the power switch. Each time you subsequently turn the power on, the power LED will blink, indicating that the auto poweroff function is disabled.

ARP ODYSSEY Module Turn the rear panel MODE SWITCH 5 off (downward position). The auto poweroff function is disabled; you don't have to turn the power off and on again to apply the setting.

Enabling the auto power-off function

ARP ODYSSEY

1. While holding down the C3, D3, and F3 keys of the keyboard, press the power switch to turn the power on.

C3 D3 F3

2. When the power LED lights up, release the power switch. Each time you subsequently turn the power on, the power LED will light up immediately, indicating that the auto poweroff function is enabled.

ARP ODYSSEY Module Turn the rear panel MODE SWITCH 5 on (upward position). The auto poweroff function is enabled; you don't have to turn the power off and on again to apply the setting.

ON

1 2 3 4 5

ON

1 2 3 4 5

ARP ODYSSEY ARP ODYSSEY Module

- 16 -

Lets make some sounds

Basic settings Set the ARP ODYSSEYs controls (sliders, switches, etc.) as shown in the illustration below. While you play the keyboard, gradually raise the VCO1 volume slider (blue) or VCO2 volume slider (green); youll hear the sound of a a sawtooth wave. Use the VCA level slider (red) to adjust the volume.

Tuning After youve adjusted the basic settings as described above, use a commercially available tuner to adjust the FREQUENCY COURSE slider and FREQUENCY FINE slider to the correct pitch.

- 17 -

O w

ne rs

m an

ua lAbout MIDI

Connecting MIDI devices By connecting the ARP ODYSSEY to a computer or external MIDI sequencer, you can control the sound generator of the ARP ODYSSEY from an external device. Use a commercially available MIDI cable to connect the ARP ODYSSEYs MIDI IN connector to the MIDI OUT connector of your external MIDI device (see Connections on page 14). MIDI IN connector: This receives MIDI messages from other MIDI devices. Connect this connector to the MIDI OUT connector of the other device.

Note messages (velocity is ignored) are the only type of MIDI messages that the ARP ODYSSEY can receive via its MIDI IN connector. The range of notes that can be received is 012 (C0) 127 (G9).

MIDI channel MIDI has sixteen channels, 1 16. If you connect an external MIDI device, you must set the MIDI channel of the ARP ODYSSEY to match the MIDI channel of your external MIDI device.

Setting the MIDI channel of the ARP ODYSSEY Heres how to set the MIDI channel of the ARP ODYSSEY. With the factory settings, this is set to channel 1. Tip: For details on how to set the MIDI channel of your external device, refer to its

operating manual.

ARP ODYSSEY

1. While holding down the C3 and C4 keys of the keyboard, press the power switch to turn the power on. The ARP ODYSSEY is in MIDI channel setting mode; the power LED blinks* to indicate the MIDI channel.

C3 C4

* The LED repeatedly blinks to indicate the MIDI channel setting; once for channel 1, twice for channel 2, and so on.

2. MIDI channels (1 16) are assigned to the keyboard as follows. Press the key corresponding to the MIDI channel that you want to assign (e.g., press the D2 key to assign channel 2). The power LED continues blinking.*

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

3. Press the C6 key to save the MIDI channel setting. When the setting has been saved, the power turns off.

C6

ARP ODYSSEY Module

Use the rear panel MODE SWITCH 1 4 to specify the MIDI channel. The MIDI channel settings are shown in the following table. The MIDI channel changes immediately when you change the setting.

Although you can change the MIDI channel during use, currentlysounding notes will turn off. Pitch bend is also reset.

1 ON

1 2 3 4

2 ON

1 2 3 4

3 ON

1 2 3 4

4 ON

1 2 3 4

5 ON

1 2 3 4

6 ON

1 2 3 4

7 ON

1 2 3 4

8 ON

1 2 3 4

9 ON

1 2 3 4

10 ON

1 2 3 4

11 ON

1 2 3 4

12 ON

1 2 3 4

13 ON

1 2 3 4

14 ON

1 2 3 4

15 ON

1 2 3 4

16 ON

1 2 3 4

ARP ODYSSEY ARP ODYSSEY Module

- 18 -

Connecting a computer Use a USB cable to directly connect the ARP ODYSSEY to a computer thats equipped with a USB port in order to receive MIDI messages in the same way as with the MIDI connectors. (see Connections on page 14) The MIDI messages that can be transmitted and received via the USB port are fixed at 1; note messages (with velocity fixed at 64 for transmission, and ignored for reception) can be transmitted and received. Since the ARP ODYSSEY Module has no keyboard, it cannot transmit note messages. The ARP ODYSSEY Module can receive MIDI pitch bend messages (2 semitones).

Tip: The only MIDI messages that are transmitted are note messages transmitted when the keyboard is played. Messages such as PROPORTIONAL PITCH CONTROL are not transmitted.

Tip: When connecting via USB, the KORG USBMIDI driver must be installed. Download the KORG USBMIDI driver from the Korg Web site ( http://www. korg.com/ ), and then install it according to the instructions in the document included with the driver.

About the MIDI implementation chart The MIDI implementation chart lists the MIDI messages that can be transmitted and received. When using a MIDI device, compare the MIDI implementation charts to check that the MIDI messages are compatible. You can download the MIDI implementation chart for this device from the Korg website.

Tip: Detailed MIDI specifications are provided under MIDI implementation. For more information on MIDI implementation, visit the Korg Web site ( http://www.korg.com/ ).

Troubleshooting

Power wont turn on . Is the AC adapter connected correctly?

No sound . Try setting the panel controls to the settings described in the Basic settings

section (page 16). Is the ARP ODYSSEY correctly connected to the input jack of your amp, mixer, or

headphones? Is your amp or mixer poweredon, and is the volume raided on that device? Could the VCA level slider (red; page 11) or the VCA GAIN slider (black; page

10) be set to 0?

Does not respond to MIDI data sent from an external device . Is the MIDI cable or USB cable connected correctly? (see Connections on page

14) Does the MIDI channel of the data being sent from the external MIDI device match

the global MIDI channel of the ARP ODYSSEY? (see MIDI channel on page 17)

Cant input sound from an external audio source . Is the source being correctly input to the rear panel EXT AUDIO INPUT jack?

Can't reset pitch bend on the ARP ODYSSEY Module . Pitch bend can be reset by receiving a MIDI message such as Reset All Controllers.

If you want to reset by operating this unit, you can turn the power off and on again, or you can operate a MODE SWITCH to temporarily change the MIDI channel.

Specifications Operating temperature range: 0 +40 C (noncondensing) Keyboard (only ARP ODYSSEY): 37note (slimkey, no velocity sensitivity, no aftertouch) Maximum Polyphony: 2 voices for duophonic; normally monophonic CONTROLLERS

Transpose positions: 2 octaves down, normal, 2 octave up Proportional Pitch Control: (Pitch down) pad: about 2 / 3 octave (Modulation) pad (Pitchup) pad: about +2 / 3 octave

Noise generator: Noise spectrum types (white and pink) Portamento: Maximum speed: about 0.01 msec./oct

Minimum speed: about 1.5 sec./oct VCO (Voltage Controlled Oscilator)

Waveforms: Sawtooth, square, pluse (dynamic pluse) Frequency range: VCO1 in low freq. mode, 0.2 Hz 20 Hz: VCO1

and VCO2 (audio range) about 20 Hz 20 kHz Warm up drift: 1/30 semitone from turn on max Pulse width: 50 % 5 % Pulse width modulation: ADSR, +45 %; LFO, +15 % Voltage controlled response: 1 V/oct Maximum frequency shifts: LFO sin wave, +1/2 oct.; LFO square wave, +1.5

oct.; ADSR, +9 oct.; S/H, +2 oct. VCO1 is low note priority, VCO2 is high note priority.

- 19 -

O w

ne rs

m an

ua l

VCF (Voltage Controlled Filter) Types: Low pass (I: 12 dB/oct., II III: 24 dB/oct.) Frequency range: 16 Hz 16 kHz Maximum usable Q: 30 Resonance: 1/2 self oscillate Voltage controlled response: C3 key (left edge): 0 V, C6 key (right edge) 3 V

VCA (Voltage Controlled Amplifier) Dynamic Range: 80 dB

RING MODULATOR Type: Digital Input signal: VCO1, VCO2 (square wave)

SAMPLE & HOLD Command sources: Keyboard or LFO trigger Sampled signals: VCO1 sawtooth wave and square wave, VCO2

square wave and pink noise ADSR ENVELOPE GENERATOR

Attack time: 5 msec. 5 sec. Decay time: 10 msec. 8 sec. Sustain Level: 0 100 % or Peak Release time: 15 msec. 10 sec.

AR ENVELOPE GENERATOR Attack time: 5 msec. 5 sec. Release time: 10 msec. 8 sec.

CONTROL INPUT JACKS Pedal: 6.3mmmonauralphonejack Portamento foot switch: 6.3mmmonauralphonejack

AUDIO OUTPUT JACKS LOW Connector: 6.3mmmonauralphonejack Maximumoutputlevel: -20dBu@10kload Outputimpedance: 10k HIGH Connector: XLR connector Maximumoutputlevel: +4dBu@1kload Outputimpedance: 330

HEADPHONES JACK Connector: 6.3mmstereophonejack Maximumoutputlevel: 50mW+50mW@33load Outputimpedance: 10 * Controllable by volume knob.

EXTERNAL AUDIO INPUT (EXT AUDIO INPUT) JACK Connector: 6.3mmmonauralphonejack Maximum input level: 10 dBu Inputimpedance: 22k

MIDI connector: IN USB connector: Type B CV IN/OUT JACKS

Keyboard CV (IN/OUT): 1 V/oct. Connector: 3.5mmmonauralphonejack

GATE IN/OUT JACKS GATE IN: +3 V (minimum) GATE OUT: +10 V, key down; 0 V all keys up Connector: 3.5mmmonauralphonejack

TRIG IN/OUT JACKS TRIG IN: +3 V pulse min., 10 sec. duration minimum TRIG OUT: +10 V pulse on key depression, 10 sec. duration Connector: 3.5mmmonauralphonejack

Power supply: AC adapter jack (DC 9 V ) Power consumption: 6.5 W Dimensions (W x D x H), Weight:

ARP ODYSSEY 502 x 380 x 120 mm / 19.76" x 14.96" x 4.72", 5 kg / 11.02 lbs

ARP ODYSSEY Module 496 x 265 x 89 mm / 19.53" x 10.43" x 3.50", 3.7 kg / 8.16 lbs

Included items: AC adapter, phone cable, miniphone cable, owners manual

Options: VP10 volume pedal, PS1/PS3 pedal switch

* Specifications and appearance are subject to change without notice for mprovement.

- 21 -

M an

ue l d

u ti

lis at

io n

Nous vous remercions davoir choisi le synthtiseur duophonique ARP ODYSSEY/ ARP ODYSSEY Module. Pour profiter au mieux de votre nouvel instrument, veuillez lire attentivement ce manuel et suivre ses consignes.

Prcautions Emplacement Lutilisation de cet instrument dans les endroits suivants peut en entraner le mauvais fonctionnement. En plein soleil Endroits trs chauds ou trs humides Endroits sales ou fort poussireux Endroits soumis de fortes vibrations A proximit de champs magntiques

Alimentation Branchez ladaptateur secteur mentionn une prise secteur de tension approprie. Evitez de brancher ladaptateur une prise de courant dont la tension ne correspond pas celle pour laquelle lappareil est conu.

Interfrences avec dautres appareils lectriques Les postes de radio et de tlvision situs proximit peuvent par consquent souffrir dinterfrences la rception. Veuillez ds lors faire fonctionner cet appareil une distance raisonnable de postes de radio et de tlvision.

Maniement Pour viter de les endommager, manipulez les commandes et les boutons de cet instrument avec soin.

Entretien Lorsque linstrument se salit, nettoyezle avec un chiffon propre et sec. Ne vous servez pas dagents de nettoyage liquides tels que du benzne ou du diluant, voire des produits inflammables.

Conservez ce manuel Aprs avoir lu ce manuel, veuillez le conserver soigneusement pour toute rfrence ultrieure.

Evitez toute intrusion dobjets ou de liquide Ne placez jamais de rcipient contenant du liquide prs de linstrument. Si le liquide se renverse ou coule, il risque de provoquer des dommages, un courtcircuit ou une lectrocution. Veillez ne pas laisser tomber des objets mtalliques dans le botier (trombones, par ex.). Si cela se produit, dbranchez lalimentation de la prise de courant et contactez votre revendeur korg le plus proche ou la surface o vous avez achet linstrument.

* Tous les noms de produits et de socits sont des marques ommerciales ou dposes de leur dtenteur respectif.

Note concernant les dispositions (Seulement EU) Quand un symbole avec une poubelle barre dune croix apparait sur le produit, le mode demploi, les piles ou le pack de piles, cela signifie que ce produit, manuel ou piles doit tre dpos chez un reprsentant comptent, et non pas dans une poubelle ou toute autre dchetterie conventionnelle. Disposer de cette manire, de prvenir les dommages pour la sant humaine et les dommages potentiels pour lenvironnement. La bonne mthode dlimination dpendra des lois et rglements applicables dans votre localit, sil vous plat, contactez votre organisme

administratif pour plus de dtails. Si la pile contient des mtaux lourds audel du seuil rglement, un symbole chimique est affich en dessous du symbole de la poubelle barre dune croix sur la pile ou le pack de piles.

REMARQUE IMPORTANTE POUR LES CLIENTS Ce produit a t fabriqu suivant des spcifications svres et des besoins en tension applicables dans le pays o ce produit doit tre utilis. Si vous avez achet ce produit via linternet, par vente par correspondance ou/et vente par tlphone, vous devez vrifier que ce produit est bien utilisable dans le pays o vous rsidez. ATTENTION: Lutilisation de ce produit dans un pays autre que celui pour lequel il a t conu peut tre dangereuse et annulera la garantie du fabricant ou du distributeur. Conservez bien votre rcpiss qui est la preuve de votre achat, faute de quoi votre produit ne risque de ne plus tre couvert par la garantie du fabricant ou du distributeur.

ARP ODYSSEY ARP ODYSSEY Module

- 22 -

Un mot propos de l'ODYSSEY

Petit historique de lODYSSEY ODYSSEY est le nom dun des plus clbres synthtiseurs du fabriquant amricain ARP Corporation, produit entre 1972 et 1981. Selon la date de production, on peut dire grosso modo quil existe trois versions de l'instrument. Ces trois moutures prsentent des diffrences tant au niveau de la finition que du caractre du timbre et des fonctions. Le modle 2800 est connu sous lappellation Rev. 1. Cette version comprend le modle original au panneau blanc produit entre 1972 et 1974 ainsi que le modle au panneau noir produit pendant prs dun an partir de 1974. Rev. 2 dsigne les modles 2810 ~ 2813. Ces instruments au panneau noir sont produits partir de 1975 jusquen 1976 environ. Cette version inclut des changements apports au filtre, ainsi qu loscillateur sur certains modles. Une prise dentre audio externe et des prises dentre CV/GATE ont t ajoutes. Les modles suivants abandonneront le contrleur Pitch Bend de type commande au profit dun contrleur de type PPC (Proportional Pitch Control), grce auquel la hauteur est contrle via la pression sur trois pads. Enfin, la Rev. 3, dsignant les modles 2820 ~ 2823, est produite partir de 1978 jusquen 1981 environ. Le panneau avant est maintenant noir avec une srigraphie orange, et le design de linstrument a considrablement chang depuis les modles 2800 ~ 2813. En face arrire, le format des connecteurs de sortie audio est pass de RCA/jack RCA/XLR.

Caractristiques principales Circuits VCO, VCF et VCA analogiques traditionnels de lARP ODYSSEY. Offre

toute lintuitivit ddition sonore propre la synthse analogique. Clavier mince 37 touches dune tessiture de 7 octaves. [LARP ODYSSEY Module

est un modle modulaire sans clavier.] Linstrument peut tre jou en mode monophonique (une note la fois) ou en mode

duophonique. En mode duo, les oscillateurs produisent des hauteurs indpendantes quand vous enfoncez deux touches la fois. (Toutefois, linstrument possde un seul filtre et amplificateur.)

Propose deux types de gnrateurs denveloppe: ADSR et AR. Oscillator sync. Cette fonction de synchronisation doscillateurs est apprcie pour

les nombreuses harmoniques aigus et la clart quelle produit. Intgre une rplique fidle du contrleur PPC (Proportional Pitch Control) original

avec son pad en caoutchouc. Large ventail dapplications de la modulation. Propose deux types de bruits. Fonctions LFO et S&H avec routage modifiable.

Sommaire

Un mot propos de l'ODYSSEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Petit historique de lODYSSEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Caractristiques principales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Schma de principe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Description des panneaux et fonctions . . . . . . . . . . . . . . . . . . . . . . 24

Panneau avant (section du type de bruit et des contrleurs) . . . . . . . . . . . . . . . . . 24 Panneau avant (section VCO-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Panneau avant (section VCO-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Panneau avant (section LFO, SAMPLE AND HOLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Panneau avant (section AUDIO MIXER, VCF, HPF, VCA) . . . . . . . . . . . . . . . . . . . . . . . 28 Panneau avant (section ENVELOPE GENERATOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Panneau arrire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Prparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Connexions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Mise sous tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Mise hors tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Fonction de mise hors tension automatique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Production de sons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Rglages de base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Accordage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

A propos de MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Connexion de dispositifs MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Connexion un ordinateur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 A propos du tableau dimplmentation MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Dpannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Fiche technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Ce manuel dcrit lutilisation de lARP ODYSSEY et de lARP ODYSSEY Module. Sauf mention contraire, les illustrations des panneaux de linstrument proviennent de lARP ODYSSEY.

- 23 -

M an

ue l d

u ti

lis at

io n

Propose les filtres des trois versions diffrentes de lARP ODYSSEY, avec choix trs simple via un slecteur unique.

La prise dentre audio de linstrument permet aussi de traiter le son dun instrument externe.

Schma de principe

NOISE GENERATOR

AUDIO MIXER

VOLTAGE CONTROLLED

FILTER

HIGH PASS

FILTER

VOLTAGE CONTROLLED

AMPLIFIER

RING MOD

SAMPLE AND

HOLD

SAMPLE AND HOLD

MIXER

VOLTAGE CONTROLLED OSCILLATORS

LOW FREQUENCY OSCILLATOR

PEDAL ADSR AND AR

ENVELOPE GENERATORS

TRIGGER

ARP ODYSSEY Module: Entre MIDI IN uniquement

KEYBOARD

MIDI IN

ARP ODYSSEY: Clavier et entre MIDI IN intgrs

Le port USB et la prise MIDI permettent de brancher linstrument un ordinateur ou un instrument MIDI.

ARP ODYSSEY ARP ODYSSEY Module

- 24 -

Description des panneaux et fonctions

Panneau avant (section du type de bruit et des contrleurs)

a

b c

d

e f g

a . Commutateur NOISE GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [WHITE, PINK] Permet de choisir le bruit rose (PINK) ou blanc (WHITE).

b . Curseur PORTAMENTO (noir) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[MINMAX] Dfinit la vitesse du portamento (une fonction produisant des transitions fluides entre les notes joues). Quand le curseur est en position MIN, le portamento est dsactiv. Plus le curseur se rapproche de la position MAX, plus les transitions de hauteur sont lentes. Vous pouvez galement activer/couper la fonction portamento via un commutateur au pied (disponible en option) branch la prise PORTAMENTO FOOTSWITCH.

c . Commutateur MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[ON, OFF] Dfinit si la fonction portamento est active ou non quand vous actionnez le slecteur TRANSPOSE. Utilisez un stylo bille pointe fine ou un objet similaire pour actionner ce commutateur.

d . Slecteur TRANSPOSE . . . . . . . . . . . . . . . . . . . . . . . . . .[2 OCTAVES UP, 0, 2 OCTAVES DOWN] Transpose la hauteur des notes du clavier par pas de deux octaves (vers le haut ou vers le bas).

e . Contrleur PPC (PROPORTIONAL PITCH CONTROL) - pad La pression (force) que vous appliquez sur ce pad dtermine lintensit de la diminution de hauteur.

f . Contrleur PPC (PROPORTIONAL PITCH CONTROL) - pad La pression (force) que vous appliquez sur ce pad dtermine lintensit du vibrato.

g . Contrleur PPC (PROPORTIONAL PITCH CONTROL) - pad La pression (force) que vous appliquez sur ce pad dtermine lintensit de laugmentation de hauteur.

- 25 -

M an

ue l d

u ti

lis at

io n

Panneau avant (section VCO-1)

c

d e f

h i j

g

a b

Les paramtres suivants dterminent le fonctionnement de loscillateur 1 (VCO1).

a . Curseur FREQUENCY COARSE (bleu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[20(0 .2)Hz2K(20)Hz] Produit un rglage brut de la hauteur. Ce rglage couvre une plage de frquence de 20 Hz 2 kHz quand le commutateur de clavier est actif, et une plage de 0,2 Hz 20 Hz quand ce commutateur est coup.

La plage de frquence (20 Hz 2 kHz) est une valeur approximative.

b . Curseur FREQUENCY FINE (bleu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [400cent] Produit un rglage fin de la hauteur.

c . Commutateur de clavier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [AUDIO KYBD ON, LF KYBD OFF] Quand ce commutateur est sur la position AUDIO KYBD ON, le VCO1 est connect au CV du clavier et produit les notes de faon habituelle. Quand il est sur la position AUDIO KYBD OFF, le VCO1 est dconnect du CV du clavier et oscille comme un LFO. Vous pouvez utiliser ce signal pour moduler le VCO2 ou comme source audio pour produire des effets sonores.

d . Curseur dintensit FM (rose) e . Curseur dintensit FM (jaune)

Rgle lintensit de la modulation de frquence (FM) quand leffet est actif.

f . Curseur PULSE WIDTH (WIDTH) (bleu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [50%MIN] Rgle la largeur de pulsation.

g . Curseur PULSE WIDTH (MOD) (rose) Rgle lintensit de la modulation de largeur de pulsation.

h . Commutateur FM source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [LFO , LFO ] Slectionne la forme donde de la modulation applique par le LFO.

i . Commutateur FM source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [S/H, ADSR ] Slectionne S/H (chantillonnageblocage) ou lenveloppe (ADSR) comme source de modulation.

j . Commutateur de source de la modulation de largeur de pulsation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [LFO , ADSR ] Dfinit la source appliquant la modulation de largeur de pulsation.

ARP ODYSSEY ARP ODYSSEY Module

- 26 -

Panneau avant (section VCO-2)

c

d e f

h i j

g

a b

Les paramtres suivants dterminent le fonctionnement de loscillateur 2 (VCO2).

a . Curseur FREQUENCY COARSE (vert) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[20(0 .2)Hz2K(20)Hz] Ce contrleur permet de rgler la hauteur entre 20 Hz et 2 kHz. Quand le commutateur SYNC est actif, ce contrleur affecte la structure des harmoniques au lieu de la hauteur.

La plage de frquence (20 Hz 2 kHz) est une valeur approximative.

b . Curseur FREQUENCY FINE (vert) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [400cent] Produit un rglage fin de la hauteur. Quand le commutateur SYNC est actif, ce contrleur affecte la structure des harmoniques au lieu de la hauteur.

c . Commutateur SYNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OFF, ON Active/coupe la synchronisation. Quand ce commutateur est sur OFF, vous pouvez jouer en mode duophonique. Quand il est sur ON, le VCO2 est synchronis avec la frquence (hauteur) du VCO1.

d . Curseur dintensit FM (rose)

e . Curseur dintensit FM (jaune) Rgle lintensit de la modulation de frquence (FM) quand leffet est actif.

f . Curseur PULSE WIDTH (WIDTH) (bleu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [50%MIN] Rgle la largeur de pulsation.

g . Curseur PULSE WIDTH (MOD) (rose) Rgle lintensit de la modulation de largeur de pulsation.

h . Commutateur FM source . . . . . . . . . . . . . . . . . . . . . . . . . . .[LFO , S/H MIXER OR PEDAL] Slectionne la source de modulation: la sinusode dun LFO ou le signal produit par la fonction S/H MIXER (mixeur dchantillonnageblocage) ou par une pdale. La position S/H MIXER OR PEDAL permet de contrler la modulation avec une pdale de volume (disponible en option) branche la prise PEDAL.

i . Commutateur FM source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [S/H, ADSR ] Slectionne S/H (chantillonnageblocage) ou lenveloppe (ADSR) comme source de modulation.

j . Commutateur de source de la modulation de largeur de pulsation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [LFO , ADSR ] Dfinit la source appliquant la modulation de largeur de pulsation.

- 27 -

M an

ue l d

u ti

lis at

io n

Panneau avant (section LFO, SAMPLE AND HOLD)

a

b c d

e f g

a . Curseur LFO FREQ (vitesse du LFO) (rose) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [0 .2Hz20Hz] Rgle la vitesse du LFO. Relevez le curseur pour augmenter la vitesse.

b . Curseur de niveau dentre S/H (bleu) Rgle le niveau auquel la forme donde produite par le VCO1 est transmise au S/H MIXER.

c . Curseur de niveau dentre S/H (blanc) Rgle le niveau auquel le bruit ou londe carre produite par le VCO2 est transmis au S/H MIXER.

d . Curseur S/H OUTPUT LAG (jaune) Adoucit les changements de tension de sortie du S/H. Plus le curseur approche de la position MAX, plus leffet de ce lissage est marqu.

e . Commutateur de source dentre S/H . . . . . . . . . . . . . . [VCO-1 , VCO-1 ] Choisit la source (forme donde du VCO1) transmise au S/H MIXER.

f . Commutateur de source dentre S/H . . . . . . . . . . . . . . . . . . .[NOISE GEN, VCO-2 ] Choisit la source (bruit ou onde carre du VCO2) transmise au S/H MIXER.

g . Commutateur de source de dclenchement S/H . . . . . . . . .[LFO TRIG, KYBD TRIG] Slectionne la source (signal du LFO ou du clavier) utilise comme dclencheur pour la dtection dun signal audio transmis par le S/H MIXER.

ARP ODYSSEY ARP ODYSSEY Module

- 28 -

Panneau avant (section AUDIO MIXER, VCF, HPF, VCA)

d e

f

c

a

g h i j

k l m

n

b

o p q r s t

a . Curseur VCF FREQ (noir) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [16Hz16KHz] Dfinit leffet du filtre passebas (LPF ou Lowpass filter). Quand ce curseur est en bas de course (16 Hz), le filtre coupe la plage de laigu du signal dentre, ce qui adoucit le son. Relevez le curseur pour claircir le son.

b . Curseur VCF RESONANCE (noir) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[MINSELF OSC] Rgle la rsonance. Ce paramtre modifie le timbre en accentuant les harmoniques aux alentours de la frquence de coupure. Une autooscillation (quand le VCF mme produit un son) est gnre un certain point quand vous relevez le curseur.

c . Commutateur VCF TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[ , , ] Slectionne le type (version) du VCF. : ODYSSEY Rev. 1 : ODYSSEY Rev. 2 : ODYSSEY Rev. 3

d . Curseur HPF CUTOFF FREQ (noir) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [16Hz16KHz] Dfinit leffet du filtre passehaut (HPF ou Highpass filter). Au fil que vous relevez le curseur, la plage du grave du signal dentre est coupe, ce qui amincit le son. Ce filtre peut se rvler trs utile pour simuler le son de certains instruments.

e . Commutateur DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[OFF, ON] Quand il est sur ON, ce commutateur permet de saturer le VCA.

f . Curseur VCA GAIN (noir) Rgle le niveau auquel le signal audio passe en permanence par le VCA.

g . Curseur NOISE/RING MOD (blanc) Rgle le niveau du signal audio transmis par le gnrateur de bruit ou le modulateur en anneau.

h . Curseur de volume du VCO-1 (bleu) Rgle le niveau du signal audio transmis par le VCO1.

i . Curseur de volume du VCO-2 (vert) Adjusts the level of the audio signal that is sent from VCO2.

j . Curseur de niveau de modulation du filtre (noir) Rgle le niveau du signal contrlant VCF FREQ, ou dfinit comment le signal transmis par S/H MIXER ouvre et ferme le filtre.

- 29 -

M an

ue l d

u ti

lis at

io n

k . Curseur de niveau de modulation du filtre (jaune) Dfinit la manire dont le filtre est ouvert et ferm par S/H (Sample/Hold) ou le LFO.

l . Curseur de niveau de modulation du filtre (rose) Dfinit la manire dont les deux gnrateurs denveloppe (AR et ADSR) contrlent le filtre.

m . Curseur de niveau VCA (rouge) Rgle le niveau auquel les gnrateurs denveloppe (AR et ADSR) contrlent le VCA. En termes pratiques, il sagit de la commande de volume principale de lARP ODYSSEY. Quand le commutateur DRIVE est sur ON, ce curseur contrle aussi la distorsion (saturation) du VCA.

n . Commutateur de source dentre de filtre (NOISE/RING MOD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [NOISE, RING MOD] Permet de choisir le bruit (NOISE) ou le modulateur en anneau (RING MOD).

o . Commutateur de source dentre de filtre (VCO-1 wave) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[VCO-1 , VCO-1 ] Dfinit la forme donde (en dents de scie ou carre) du VCO1. Si vous avez choisi londe carre, le curseur PULSE WIDTH (page 25) vous permet de modifier la largeur de pulsation et de passer dune onde carre une onde pulsation.

p . Commutateur de source dentre de filtre (VCO-2 wave) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[VCO-2 , VCO-2 ] Dfinit la forme donde (en dents de scie ou carre) du VCO2. Si vous avez choisi londe carre, le curseur PULSE WIDTH (page 26) vous permet de modifier la largeur de pulsation et de passer dune onde carre une onde pulsation.

q . Commutateur de source de modulation de filtre (KYBD CV/S/H MIXER OR PEDAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[KYBD CV, S/H MIXER OR PEDAL] Dfinit la source de contrle du filtre. Si vous slectionnez KYBD CV (tension de contrle du clavier), le signal normalement utilis pour transmettre les donnes des touches du clavier au VCO peut tre mis profit pour ouvrir et fermer le filtre. Cela permet par exemple de produire un effet de jeu o le filtre souvre davantage en rponse des notes aigus.

Quand ce commutateur est sur S/H MIXER OR PEDAL, cest le signal transmis par le S/H MIXER qui ouvre et ferme le filtre. Si une pdale de volume (disponible en option) est branche la prise PEDAL, vous pouvez utiliser son signal pour contrler le VCF et produire un effet similaire une pdale Wah.

r . Commutateur de source de modulation de filtre (S/H/LFO) . . . .[S/H, LFO ] Dfinit la source de contrle du filtre. Vous pouvez produire un effet Wah en modulant le filtre avec le LFO.

s . Commutateur de source de modulation de filtre (ADSR/AR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[ADSR , AR ] Dfinit le gnrateur denveloppe de contrle du filtre.

t . Commutateur VCA EG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[AR , ADSR ] Dfinit le gnrateur denveloppe de contrle du VCA.

ARP ODYSSEY ARP ODYSSEY Module

- 30 -

Panneau avant (section ENVELOPE GENERATOR)

c

a

b

d e f

h i j

g

a . Curseur AR EG - ATTACK (rouge) Rgle la vitesse dattaque (ATTACK) du gnrateur denveloppe AR.

b . Curseur AR EG - RELEASE (rouge) Rgle le temps de relchement (RELEASE) du gnrateur denveloppe AR.

c . Diode dalimentation Cette diode est allume quand linstrument est sous tension et steint quand il est mis hors tension. Si la fonction de coupure automatique dalimentation est dsactive, la diode dalimentation clignote plusieurs fois puis reste allume la mise sous tension.

d . Curseur ADSR EG - ATTACK (rouge) Rgle la vitesse dattaque (ATTACK) du gnrateur denveloppe ADSR.

e . Curseur ADSR EG - DECAY (rouge) Rgle le temps de chute (DECAY) du gnrateur denveloppe ADSR.

f . Curseur ADSR EG - SUSTAIN (rouge) Rgle le temps de maintien (SUSTAIN) du gnrateur denveloppe ADSR.

g . Curseur ADSR EG - RELEASE (rouge) Rgle le temps de relchement (RELEASE) du gnrateur denveloppe ADSR.

h . Commutateur de source de dclenchement ADSR . . . . [KYBD GATE, LFO REPEAT ] Dfinit le dclencheur envoy au gnrateur denveloppe ADSR. Si ce commutateur est sur KYBD GATE, le dclencheur produit par le clavier est transmis lenveloppe. Sil est sur LFO REPEAT, londe pulsation du LFO est envoye au gnrateur denveloppe, qui rpte lenveloppe en boucle la vitesse dfinie via le curseur LFO FREQ.

i . Commutateur de rptition ADSR . . . . . . . . . . . . . . . . . . [KYBD REPEAT, AUTO REPEAT] Ce commutateur ne produit un effet que si le slecteur de source de dclenchement ADSR ou AR est sur LFO REPEAT. Si le commutateur est sur KYBD REPEAT, le dclencheur de LFO envoy de faon rpte au gnrateur denveloppe continue dtre rpt tant que la touche est enfonce. Si ce slecteur est sur AUTO REPEAT, les rptitions continuent indpendamment du statut de note (active/coupe) du clavier.

j . Commutateur de source de dclenchement AR . . . [KYBD GATE, LFO REPEAT ] Dfinit le dclencheur envoy au gnrateur denveloppe AR. La fonction de ce commutateur est identique celle du commutateur de source de dclenchement ADSR.

- 31 -

M an

ue l d

u ti

lis at

io n

Panneau arrire

e f g h i j k l

m n o

b c da

onm

p

k le f g h i jb c da

ARP ODYSSEY Module

ARP ODYSSEY

a . Crochet pour cble Enroulez le cble de ladaptateur secteur autour de ce crochet pour viter toute dconnexion accidentelle.

b . Prise DC 9V Branchez ici ladaptateur secteur fourni. Branchez dabord ladaptateur secteur linstrument, puis connectezle une prise de courant de tension approprie.

c . Interrupteur dalimentation Il met lappareil sous/hors tension. Pour couper lalimentation, maintenez le bouton enfonc.

d . Prise MIDI IN Cette prise permet de brancher un instrument MIDI externe et de recevoir des donnes MIDI.

e . Port USB B Permet de relier cet instrument un ordinateur et dchanger des donnes MIDI entre les deux appareils.

f . Prise PEDAL Permet de brancher une pdale de volume (disponible en option). Cette prise permet aussi de brancher un squenceur SQ1 afin de piloter lARP ODYSSEY.

g . Prise PORTAMENTO FOOTSWITCH Permet de brancher un commutateur au pied (disponible en option).

h . Prise OUTPUT LOW Permet de brancher un ampli ou une enceinte active.

i . Prise OUTPUT HIGH Permet de brancher une console de mixage ou un ampli dot dune prise XLR.

j . Prise EXT AUDIO INPUT Si vous utilisez votre ARP ODYSSEY comme processeur deffet, branchez ici la source audio externe via un cble prises jack mono. Le signal audio reu la prise EXT AUDIO INPUT est transmis la section AUDIO MIXER et transite par le filtre (VCF) et lamplificateur (VCA). Rglez le volume avec la commande du dispositif externe connect. Astuce: Vous pouvez relier la prise EXT AUDIO INPUT

la prise casque avec le cble fiches jack fourni, afin de gnrer de la rtroaction dans le systme et ainsi largir la palette de cration sonore. Rglez lintensit de rtroaction avec la commande de volume du casque.

k . Commande de volume casque Rgle le volume du casque branch. Si vous appliquez de la rtroaction, cette commande rgle le niveau de rtroaction.

l . Prise casque Branchezy un casque dcoute stro. Cette prise produit le mme signal que les prises OUTPUT LOW et OUTPUT HIGH. Pour appliquer de la rtroaction, reliez cette prise la prise EXT AUDIO INPUT de lARP ODYSSEY.

m . Prises CV IN/OUT Ces prises reoivent et transmettent la tension de contrle (une tension identifiant la hauteur).

n . Prises GATE IN/OUT Ces prises reoivent et transmettent un signal de Gate (indiquant quun son est produit).

o . Prises TRIG IN/OUT Ces prises reoivent et transmettent un signal de dclenchement (indiquant quune touche du clavier est enfonce). Astuce: Vous pouvez relier la prise TRIG IN et la prise

GATE OUT de linstrument avec le cble fiches minijack fourni. Dans ce cas, lenveloppe ADSR nest pas redclenche, ce qui vous permet de jouer legato.

p . Commutateur MODE SWITCH (ARP ODYSSEY Module uniquement) Ce commutateur (en fait un set de 5 commutateurs) permet de rgler le canal MIDI et la fonction de coupure automatique de lalimentation. Quand vous manipulez le commutateur, la diode dalimentation clignote.

Cble fiches jack (fourni)

Cble ches minijack (fourni)

ARP ODYSSEY ARP ODYSSEY Module

- 32 -

Prparations

Connexions Lillustration suivante montre un exemple typique de connexions. Branchez le matriel rpondant vos besoins.

brancher une prise de courant

Adaptateur secteur (fourni)

Commutateur au pied

Enceintes actives, etc.

Cble XLR

Cble USB

Ordinateu

MIDI OUT

Casque Pdale de volume

Source audio, etc. externe

Cble MIDI Cble fiches jack mono

Cble fiches jack mono

Cble fiches jack mono

ou

Autres exemples de connexions Vous pouvez connecter votre ARP ODYSSEY un squenceur laide de cbles fiches minijack mono, comme illustr cidessous. Cela vous permet de piloter les sons de votre ARP ODYSSEY avec le squenceur. Si vous branchez lARP ODYSSEY un SQ1, reliez la prise PEDAL de lARP ODYSSEY la prise CV OUT du SQ1 afin de pouvoir contrler la hauteur et le filtre du VCO 2 de lARP ODYSSEY.

CV OUT

GATE OUT CV IN

GATE IN

CV OUT

Squenceur, etc.

bouchon de conversion

Veillez mettre tous les appareils hors tension avant deffectuer la moindre connexion. Veillez mettre tout votre matriel hors tension avant deffectuer la moindre connexion. Effectuer des branchements quand un appareil est sous tension pourrait endommager les enceintes ou causer un dysfonctionnement, voire un endommagement de votre matriel.

Pour pouvoir utiliser une pdale de volume Korg VP10 (disponible en option), raccordez sa prise OUT 1 ou OUT 2 la prise PEDAL de lARP ODYSSEY avec un cble prises jack mono. Dans ce cas, veillez rgler la commande MINIMUM VOLUME de la VP10 sur 0 (niveau minimum).

Astuce: Pour activer/couper le portamento au pied, branchez un commutateur au pied Korg PS1 ou PS3 (disponible en option) la prise PORTAMENTO FOOTSWITCH de votre ARP ODYSSEY. Le portamento est dsactiv quand vous enfoncez le commutateur au pied. Quand vous le relchez, leffet de portamento est appliqu conformment au rglage de vitesse dfini avec le curseur PORTAMENTO.

- 33 -

M an

ue l d

u ti

lis at

io n

Mise sous tension Mettez vos enceintes actives ou tout autre dispositif externe hors tension avant

de mettre votre ARP ODYSSEY sous tension. 1. Abaissez le curseur de niveau VCA (page 29) et le curseur VCA GAIN (page

28) de lARP ODYSSEY en bas de course.

2. Appuyez sur linterrupteur dalimentation de lARP ODYSSEY pour le mettre sous tension. La diode dalimentation sallume.

3. Diminuez le volume de vos enceintes actives ou de tout autre systme damplification externe et mettezle(s) sous tension.

4. Rglez le volume de vos enceintes actives ou de votre sono sur un niveau appropri, puis ajustez le curseur de niveau VCA de lARP ODYSSEY.

Astuce: Si vous ntes pas familiaris avec la procdure de cration de sons, nous vous conseillons deffectuer maintenant les rglages dcrits dans la section Rglages lmentaires (page 34).

Mise hors tension 1. Diminuez le volume de vos enceintes actives ou de tout autre systme

damplification externe et mettezle(s) hors tension.

2. Appuyez sur linterrupteur dalimentation de lARP ODYSSEY jusqu ce que sa diode dalimentation steigne, puis relchez linterrupteur.

Fonction de mise hors tension automatique LARP ODYSSEY est dot dune fonction de coupure automatique de lalimentation qui, comme son nom lindique, met automatiquement linstrument hors tension quand il est rest environ quatre heures sans tre utilis ou manipul. La fonction de coupure automatique de lalimentation est active par dfaut.

Changer le rglage de coupure automatique dalimentation Cette section dcrit comment changer le rglage de fonction de coupure automatique dalimentation.

Ne mettez jamais linstrument hors tension pendant que vous effectuez ce rglage. Cela risquerait dendommager les donnes et de causer un dysfonctionnement de linstrument.

Astuce: Le rglage de la fonction de coupure automatique dalimentation est mmoris et conserv la mise hors tension de linstrument.

Pour dsactiver la fonction de coupure automatique d'alimentation

ARP ODYSSEY

1. Mettez linstrument sous tension en maintenant les touches Do3, R3 et Mi3 de son clavier enfonces.

Do3 R3 Mi3

2. Attendez que la diode dalimentation clignote plusieurs fois puis reste allume avant de relcher linterrupteur dalimentation. Par la suite, chaque fois que vous mettez linstrument sous tension, sa diode dalimentation clignote, indiquant que la fonction de coupure automatique dalimentation est dsactive.

ARP ODYSSEY Module Placez le commutateur MODE SWITCH 5 en face arrire en position Off (en bas). La fonction de coupure automatique dalimentation est dsactive. Vous ne devez pas mettre linstrument hors tension puis nouveau sous tension pour appliquer le rglage.

Pour activer nouveau la fonction de coupure automatique d'alimentation

ARP ODYSSEY

1. Mettez linstrument sous tension en maintenant les touches Do3, R3 et Fa3 de son clavier enfonces.

Do3 R3 Fa3

2. Attendez que la diode dalimentation sallume avant de relcher linterrupteur dalimentation. Par la suite, chaque fois que vous mettez linstrument sous tension, sa diode dalimentation sallume immdiatement, indiquant que la fonction de coupure automatique dalimentation est active.

ARP ODYSSEY Module Placez le commutateur MODE SWITCH 5 en face arrire en position On (en haut). La fonction de coupure automatique dalimentation est active. Vous ne devez pas mettre linstrument hors tension puis nouveau sous tension pour appliquer le rglage.

ON

1 2 3 4 5

ON

1 2 3 4 5

ARP ODYSSEY ARP ODYSSEY Module

- 34 -

Production de sons

Rglages de base Rglez les commandes (curseurs, commutateur, etc.) de lARP ODYSSEY comme illustr cidessous. Jouez sur le clavier tout en augmentant progressivement le niveau avec le curseur de volume du VCO1 (bleu) ou le curseur de volume du VCO2 (vert). Le son que vous obtenez est une onde en dents de scie. Rglez le volume avec le curseur de niveau VCA (rouge).

Accordage Aprs avoir effectu les rglages de base dcrits cidessus, accordez linstrument en rglant ses curseurs FREQUENCY COARSE et FREQUENCY FINE la hauteur (frquence) correcte avec un accordeur disponible dans le commerce.

- 35 -

M an

ue l d

u ti

lis at

io n

A propos de MIDI

Connexion de dispositifs MIDI Vous pouvez brancher lARP ODYSSEY un ordinateur ou squenceur MIDI externe afin de piloter le gnrateur de son du synthtiseur avec ce dispositif externe. Procurezvous un cble MIDI disponible dans le commerce pour relier la prise MIDI IN de lARP ODYSSEY la prise MIDI OUT du dispositif MIDI utilis (voyez Connexions la page 32.). Connecteur MIDI IN: Il reoit les messages MIDI provenant d'autres dispositifs MIDI. Reliez ce connecteur au connecteur MIDI OUT de l'autre dispositif.

Les messages de note (le toucher est ignor) sont les seuls messages MIDI que lARP ODYSSEY peut recevoir via sa prise MIDI IN. Linstrument peut recevoir la plage de notes suivante: 012 (Do0) 127 (Sol9).

Canal MIDI La norme MIDI offre 16 canaux (1 ~ 16). Pour pouvoir utiliser un dispositif MIDI externe connect lARP ODYSSEY, vous devez rgler les deux appareils sur le mme canal MIDI.

Rglage du canal MIDI sur lARP ODYSSEY Voyons prsent comment rgler le canal MIDI de votre ARP ODYSSEY. Par dfaut, le canal MIDI 1 est assign linstrument. Astuce: Pour savoir comment rgler le canal MIDI sur votre dispositif externe,

reportezvous son mode demploi.

ARP ODYSSEY

1. Mettez linstrument sous tension en maintenant les touches Do3 et Do4 de son clavier enfonces. Le mode de slection de canal MIDI de lARP ODYSSEY est activ. Le clignotement* de la diode dalimentation indique le canal MIDI actif.

Do3 Do4

* Le nombre de clignotements de la diode indique le numro du canal MIDI: un clignotement indique le canal 1, deux clignotements le canal 2, et ainsi de suite.

2. Les canaux MIDI (1 ~ 16) sont assigns aux touches suivantes du clavier. Appuyez sur la touche du clavier correspondant au canal MIDI vis (par exemple, pour activer le canal MIDI 2, enfoncez la touche R2). La diode dalimentation continue de clignoter.*

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

3. Enfoncez la touche Do6 pour sauvegarder le rglage de canal MIDI de linstrument. Une fois le rglage mmoris, linstrument se met hors tension.

Do6

ARP ODYSSEY Module

Utilisez les commutateurs MODE SWITCH 1 ~ 4 en face arrire pour dfinir le canal MIDI. Les rglages de canal MIDI sont dcrits dans le tableau cidessous. Le canal MIDI change immdiatement quand vous manipulez les commutateurs.

Vous pouvez changer de canal MIDI pendant le jeu, mais dans ce cas les notes en cours de production seront coupes. La fonction de jeu Pitch Bend est galement initialise.

1 ON

1 2 3 4

2 ON

1 2 3 4

3 ON

1 2 3 4

4 ON

1 2 3 4

5 ON

1 2 3 4

6 ON

1 2 3 4

7 ON

1 2 3 4

8 ON

1 2 3 4

9 ON

1 2 3 4

10 ON

1 2 3 4

11 ON

1 2 3 4

12 ON

1 2 3 4

13 ON

1 2 3 4

14 ON

1 2 3 4

15 ON

1 2 3 4

16 ON

1 2 3 4

ARP ODYSSEY ARP ODYSSEY Module

- 36 -

Connexion un ordinateur Reliez le port USB de lARP ODYSSEY celui de votre ordinateur laide dun cble USB. Comme la prise MIDI IN, la prise USB de lARP ODYSSEY permet de recevoir des messages MIDI. (voyez Connexions la page 32.) Le port USB permet de transmettre et de recevoir exclusivement des messages de note (linstrument transmet la valeur de toucher fixe de 64 et ignore les donnes de toucher reues). Le modle ARP ODYSSEY Module ne possde pas de clavier et ne peut donc pas transmettre de message de note. LARP ODYSSEY Module peut recevoir les messages MIDI de Pitch Bend (2 demitons).

Astuce: Les seuls messages MIDI transmis sont les messages de note produits quand vous jouez sur le clavier. Les messages de contrleurs tels que PROPORTIONAL PITCH CONTROL ne sont pas transmis.

Astuce: Pour pouvoir exploiter la connexion USB, vous devez installer le pilote USB MIDI de KORG. Tlchargez le pilote USBMIDI de KORG depuis le site internet de Korg ( http://www.korg.com/ ) et installezle conformment aux instructions de la documentation accompagnant le pilote.

A propos du tableau dimplmentation MIDI Le tableau dimplmentation MIDI fournit la liste des messages MIDI qui peuvent tre transmis/reus par linstrument. Si vous avez lintention dutiliser un dispositif MIDI, vrifiez la compatibilit des messages MIDI dans le tableau dimplmentation MIDI de chaque instrument. Vous pouvez tlcharger le tableau dimplmentation MIDI (MIDI Implementation Chart) de cet instrument sur le site Internet de Korg.

Astuce: Limplmentation MIDI offre une description dtaille des caractristiques MIDI de linstrument. Pour en savoir plus sur limplmentation MIDI, surfez sur le site internet de Korg ( http://www.korg.com/ ).

Dpannage Linstrument ne sallume pas . Ladaptateur secteur estil correctement connect?

Aucun son . Rglez les commandes de linstrument comme dcrit sous Rglages de base (page

32). Votre ampli, console ou casque estil correctement connect lARP ODYSSEY? Votre ampli ou console estil sous tension? Son volume estil suffisant? Le curseur de niveau VCA (rouge; page 29) ou le curseur VCA GAIN (noir; page

28) nestil pas sur 0?

Linstrument ne rpond pas aux messages MIDI du dispositif externe . Le cble MIDI ou USB estil correctement connect? (voyez Connexions la page 32.) Le rglage de canal global MIDI de lARP ODYSSEY et le rglage de canal MIDI du

dispositif transmettant les messages sontils identiques? (voyez Canal MIDI la page 35.)

Le son de la source audio externe connecte est inaudible . La source audio externe estelle bien connecte la prise EXT AUDIO INPUT?

Impossible dinitialiser le Pitch Bend sur lARP ODYSSEY Module . La fonction de jeu Pitch Bend peut tre initialise par la transmission dun message

MIDI du type Reset All Controllers (initialisation de toutes les fonctions de jeu). Vous pouvez effectuer linitialisation sur linstrument mme en le mettant hors tension puis nouveau sur tension, ou manipuler un commutateur MODE SWITCH pour changer temporairement de canal MIDI.

- 37 -

M an

ue l d

u ti

lis at

io n

Fiche technique Temperature de fonctionnement: 0 ~ +40 C (sans condensation) Clavier (ARP ODYSSEY uniquement): 37 notes (de type Slimkey, sans dynamique ni

aftertouch) Polyphonie: 2 voix maximum en mode duophonique;

monophonique en mode normal FONCTIONS DE JEU

Transposition: 2 octaves vers le bas, hauteur normale, 2 octaves vers le haut

Contrleurs Proportional Pitch Control (PPC): Pad (diminution de hauteur): environ 2 / 3

octaves Pad (modulation) Pad (augmentation de hauteur): environ +2 / 3

octaves Gnrateur de bruit: A spectres de bruit (blanc et rose) Portamento: Vitesse maximum: environ 0,01 ms/oct.

Vitesse maximum: environ 1,5 s/oct. VCO (Voltage Controlled Oscillator)

Formes donde: Ondes en dents de scie, carre, pulsation (dynamique)

Plage de frquence: VCO1 en mode basse frquence (low freq.), 0,2 Hz ~ 20 Hz: VCO1 et VCO2 (spectre audio) denviron 20 Hz ~ 20 kHz

Imprcision daccord la mise sous tension: 1/30e de demiton maximum

Largeur de pulsation: 50 % ~ 5 % Modulation de largeur de pulsation (PWM): ADSR, +45 %; LFO, +15 % Rponse la tension de contrle (VC): 1V/oct. Dcalages de frquence maximum: Sinusode de LFO, +1/2 oct.; onde carre de LFO,

+1,5 oct.; ADSR, +9 oct.; S/H, +2 oct. VCO1 accorde la priorit aux notes graves et VCO2 aux notes aigus.

VCF (Voltage Controlled Filter) Types: Passebas (I: 12 dB/oct., II III: 24 dB/oct.) Plage de frquence: 16 Hz ~ 16 kHz Facteur Q max. utilisable: 30 Rsonance: 1/2 ~ autooscillation Rponse la tension de contrle (VC): Touche Do3 (bord gauche): 0 V, touche Do6 (bord

droit) 3 V VCA (Voltage Controlled Amplifier)

Plage dynamique: 80 dB MODULATEUR EN ANNEAU

Type: Numrique Signal dentre: VCO1, VCO2 (onde carre)

ECHANTILLONNEUR BLOQUEUR (SAMPLE & HOLD) Sources de contrle: Dclenchement via le clavier ou LFO Signaux chantillonns: Onde en dents de scie ou onde carre du VCO1,

onde carre et bruit rose du VCO2 GENERATEUR DENVELOPPE ADSR (ADSR ENVELOPE GENERATOR)

Vitesse dattaque (Attack): 5 ms ~ 5 sec. Temps de chute (Decay): 10 ms ~ 8 sec. Niveau de maintien (Sustain): 0 ~ 100 % ou pic (Peak) Temps aprs relchement (Release): 15 ms ~ 10 sec.

GENERATEUR DENVELOPPE AR (AR ENVELOPE GENERATOR) Vitesse dattaque (Attack): 5 ms ~ 5 sec. Temps aprs relchement (Release): 10 ms ~ 8 sec.

PRISES DENTREE DE CONTROLE PEDAL: jackmono(:6,3mm) PORTAMENTO FOOTSWITCH: jackmono(:6,3mm)

PRISES DE SORTIE AUDIO LOW Type: jackmono(:6,3mm) Niveaudesortiemaximum: -20dBuavecunechargede10k Impdancedesortie: 10k HIGH Type: Connecteur XLR Niveaudesortiemaximum: +4dBuavecunechargede1k Impdancedesortie: 330

ARP ODYSSEY ARP ODYSSEY Module

- 38 -

PRISE CASQUE Type: jackstro(:6,3mm) Niveaudesortiemaximum: 50mW+50mWavecunechargede33 Impdancedesortie: 10 * Contrlable avec la commande de volume casque.

PRISE DENTREE EXTERNE (EXT AUDIO INPUT) Type: jackmono(:6,3mm) Niveau dentre maximum: 10 dBu Impdancedentre: 22k

Prise MIDI: IN Port USB: Type B PRISES CV IN/OUT

Tension de contrle clavier (IN/OUT): 1 V/oct. Type: jackmono(:3,5mm)

PRISES GATE IN/OUT GATE IN: +3 V (minimum) GATE OUT: +10 V, touche enfonce; 0 V:aucune touche enfonce Type: jackmono(:3,5mm)

PRISES TRIG IN/OUT TRIG IN: Pulsation de +3 V min., dune dure min. de 10 sec. TRIG OUT: Pulsation de +10 V au relchement de touche;

dure de 10 sec. Type: jackmono(:3,5mm)

Alimentation: Prise pour adaptateur secteur (DC 9 V ) Consommation: 6,5 W Dimensions (L x P x H), Poids:

ARP ODYSSEY 502 x 380 x 120 mm, 5 kg ARP ODYSSEY Module 496 x 265 x 89 mm, 3,7 kg

Accessoires fournis: Adaptateur secteur, cble fiches jack, cble fiches minijack, Manuel dutilisation

Options: Pdale volume VP10, commutateur au pied PS1/ PS3

* Les caractristiques et laspect du produit sont susceptibles dtre modifis sans avis pralable en vue dune amlioration.

- 39 -

Be di

en un

gs an

le it

un g

Vielen Dank, dass Sie sich fr den duophonischen Synthesizer ARP ODYSSEY/ ARP ODYSSEY Module entschieden haben. Bitte lesen Sie sich diese Anleitung vollstdig durch, um bei der Bedienung alles richtig zu machen.

Vorsichtsmanahmen Aufstellungsort Vermeiden Sie das Aufstellen des Gerts an Orten, an denen. es direkter Sonneneinstrahlung ausgesetzt ist; hohe Feuchtigkeit oder Extremtemperaturen auftreten knnen; Staub oder Schmutz in groen Mengen vorhanden sind; das Gert Erschtterungen ausgesetzt sein kann. in der Nhe eines Magnetfeldes.

Stromversorgung Schlieen Sie das optionale Netzteil nur an eine geeignete Steckdose an. Verbinden Sie es niemals mit einer Steckdose einer anderen Spannung.

Streinflsse auf andere Elektrogerte Dieser kann bei in der Nhe aufgestellten Rundfunkempfnger oder Fernsehgerten Empfangsstrungen hervorrufen. Betreiben Sie solche Gerte nur in einem geeigneten Abstand von diesem Erzeugnis.

Bedienung Vermeiden Sie bei der Bedienung von Schaltern und Reglern unangemessenen Kraftaufwand.

Reinigung Bei auftretender Verschmutzung knnen Sie das Gehuse mit einem trockenen, sauberen Tuch abwischen. Verwenden Sie keinerlei Flssigreiniger wie beispielsweise Reinigungsbenzin, Verdnner oder Splmittel. Verwenden Sie niemals brennbare Reiniger.

Bedienungsanleitung Bewahren Sie diese Bedienungsanleitung gut auf, falls Sie sie spter noch einmal bentigen.

Flssigkeiten und Fremdkrper Stellen Sie niemals Behltnisse mit Flssigkeiten in der Nhe des Gerts auf. Wenn Flssigkeit in das Gert gelangt, knnen Beschdigung des Gerts, Feuer oder ein elektrischer Schlag die Folge sein. Beachten Sie, dass keinerlei Fremdkrper in das Gert gelangen. Sollte ein Fremdkrper in das Gert gelangt sein, so trennen Sie es sofort vom Netz. Wenden Sie sich dann an Ihren KORGFachhndler.

* Alle Produkt und Firmennamen sind Warenzeichen oder eingetragene Warenzeichen der betreffenden Eigentmer.

Hinweis zur Entsorgung (Nur EU) Wenn Sie das Symbol mit der durchgekreuzten Mlltonne auf Ihrem Produkt, der dazugehrigen Bedienungsanleitung, der Batterie oder dem Batteriefach sehen, mssen Sie das Produkt in der vorgeschriebenen Art und Weise entsorgen. Dies bedeutet, dass dieses Produkt mit elektrischen und elektronischen Komponenten nicht mit dem normalen Hausmll entsorgt werden darf. Fr Produkte dieser Art existiert ein separates, gesetzlich festgelegtes Entsorgungssystem. Gebrauchte elektrische und elektronische Gerte mssen

separat entsorgt werden, um ein umweltgerechtes Recycling sicherzustellen. Diese Produkte mssen bei benannten Sammelstellen abgegeben werden. Die Entsorgung ist fr den Endverbraucher kostenfrei! Bitte erkundigen sie sich bei ihrer zustndigen Behrde, wo sie diese Produkte zur fachgerechten Entsorgung abgeben knnen. Falls ihr Produkt mit Batterien oder Akkumulatoren ausgerstet ist, mssen sie diese vor Abgabe des Produktes entfernen und separat entsorgen (siehe oben). Die Abgabe dieses Produktes bei einer zustndigen Stelle hilft ihnen, dass das Produkt umweltgerecht entsorgt wird. Damit leisten sie persnlich einen nicht unerheblichen Beitrag zum Schutz der Umwelt und der menschlichen Gesundheit vor mglichen negativen Effekten durch unsachgeme Entsorgung von Mll. Batterien oder Akkus, die Schadstoffe enthalten, sind auch mit dem Symbol einer durchgekreuzten Mlltonne gekennzeichnet. In der Nhe zum Mlltonnensymbol befindet sich die chemische Bezeichnung des Schadstoffes. Cd oder NiCd steht fr Cadmium, Pb fr Blei und Hg fr Quecksilber.

WICHTIGER HINWEIS FR KUNDEN Dieses Produkt wurde unter strenger Beachtung von Spezifikationen und Spannungsanforderungen hergestellt, die im Bestimmungsland gelten. Wenn Sie dieses Produkt ber das Internet, per Postversand und/oder mit telefonischer Bestellung gekauft haben, mssen Sie besttigen, dass dieses Produkt fr Ihr Wohngebiet ausgelegt ist. WARNUNG: Verwendung dieses Produkts in einem anderen Land als dem, fr das es bestimmt ist, verwendet wird, kann gefhrlich sein und die Garantie des Herstellers oder Importeurs hinfllig lassen werden. Bitte bewahren Sie diese Quittung als Kaufbeleg auf, da andernfalls das Produkt von der Garantie des Herstellers oder Importeurs ausgeschlossen werden kann.

ARP ODYSSEY ARP ODYSSEY Module

- 40 -

Einleitung zum ODYSSEY

Was ist der ODYSSEY? Der ODYSSEY wurde zwischen 1972 und 1981 von ARP produziert und gehrte zu den bekanntesten Produkten dieses Herstellers. Je nach Baujahr gibt es drei Versionen, die sich nicht nur im Erscheinungsbild, sondern auch in Klangcharakteristik und Funktionalitt unterscheiden. Modell 2800 ist auch als Mk1 bekannt: Dazu zhlen das ursprngliche, von 1972 bis 1974 produzierte Modell mit weiem Gehuse und das von 1974 bis etwa 1975 produzierte Modell mit schwarzem Gehuse. Die Modelle 2810 bis 2813 sind als Mk2 bekannt: Dazu zhlen die von 1975 bis etwa 1976 produzierten Modelle mit schwarzem Gehuse. Neben Modifikationen an den Filtern wurde bei einigen Modellen auch Modifikationen am Oszillator vorgenommen. Zudem wurden ein Eingang fr externe Audiogerte sowie CV/ GATE Eingnge hinzugefgt. Bei spteren Modellen wurde der als Drehregler gestaltete Pitchbender von einem PPC (Proportional Pitch Control) ersetzt. Die Modelle 2820 bis 2823 sind als Mk3 bekannt und wurden von 1978 bis etwa 1981 produziert. Das Gehuse ist nun schwarz mit orangefarbenem Siebdruck, und das Design unterscheidet sich deutlich von dem der Modelle 2800 bis 2813. Als Audio Ausgnge gab es nunmehr XLR/Klinkenbuchsen anstelle von RCA/Klinkenbuchsen.

Die wichtigsten Funktionen Traditionelle analoge VCO, VCF und VCASchaltkreise des ARP ODYSSEY. Diese

ermglichen spontanes Editieren von Sounds, wie es nur analoge Synthesizer bieten. 37NotenSlimkeyTastatur mit einem Tonumfang von sieben Oktaven. [Der ARP

ODYSSEY Module besitzt keine Tastatur.] Sie knnen das Instrument monophonisch spielen oder im duophonischen Modus

beim gleichzeitigen Spielen zweier Tasten den Oszillatoren zwei unterschiedlich hohe Tne hervorlocken. (Wobei es nur ein Filter und nur einen Verstrker gibt.)

Zwei Arten von Hllkurvengeneratoren: ADSR und AR. OscillatorSynchronisation. Fr seine Schrfe geschtztes Feature zum Erzeugen

zahlreicher hochfrequenter Obertne. Reproduktion des originalen PPC (Proportional Pitch Control)Gummipads. Zahlreiche Mglichkeiten der Modulation. Zwei Arten von Rauschen. LFO und S&H, deren Routing Sie umschalten knnen. Smtliche Filter der drei unterschiedlichen ARP ODYSSEYModellreihen, die mit

einem einzigen Schalter angewhlt werden knnen.

Inhalt

Einleitung zum ODYSSEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Was ist der ODYSSEY? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Die wichtigsten Funktionen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Blockschaltbild . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Funktionen und Regler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Oberseite (Rauschart, Regler-Sektion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Oberseite (VCO 1-Sektion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Oberseite (VCO-2-Sektion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Oberseite (LFO, SAMPLE AND HOLD-Sektion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Oberseite (AUDIO MIXER, VCF, HPF, VCA-Sektion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Oberseite (ENVELOPE GENERATOR-Sektion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Rckseite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Vorbereitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Anschlsse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Einschalten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Ausschalten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Energiesparfunktion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Erzeugen wir nun ein paar Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Grundlegende Einstellungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Stimmen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

ber MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 MIDI-Gerte anschlieen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Computer anschlieen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 ber die MIDI-Implementationstabelle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Fehlersuche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Diese Anleitung erklrt die Bedienung des ARP ODYSSEY und des ARP ODYSSEY Module. Solange nicht anders angegeben, beziehen sich die Abbildungen auf den ARP ODYSSEY.

- 41 -

Be di

en un

gs an

le it

un g

Dank einer AudioEingangsbuchse knnen Sie auch den Klang externer Musikinstrumente bearbeiten.

USBPort und MIDI Anschlsse zum Anschluss eines Computers oder eines MIDI Instruments.

Blockschaltbild

NOISE GENERATOR

AUDIO MIXER

VOLTAGE CONTROLLED

FILTER

HIGH PASS

FILTER

VOLTAGE CONTROLLED

AMPLIFIER

RING MOD

SAMPLE AND

HOLD

SAMPLE AND HOLD

MIXER

VOLTAGE CONTROLLED OSCILLATORS

LOW FREQUENCY OSCILLATOR

PEDAL ADSR AND AR

ENVELOPE GENERATORS

TRIGGER

ARP ODYSSEY Module: Nur MIDI IN

KEYBOARD

MIDI IN

ARP ODYSSEY: Integrierte Tastatur und MIDI IN

ARP ODYSSEY ARP ODYSSEY Module

- 42 -

Funktionen und Regler

Oberseite (Rauschart, Regler-Sektion)

a

b c

d

e f g

a . NOISE GENERATOR-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [WHITE, PINK] Zur Auswahl zwischen Weiem und Rosa Rauschen.

b . PORTAMENTO-Slider (Schwarz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[MINMAX] Zur Regelung des Portamento Effekts (verndert die Dauer der Tonhhennderung). Steht der Slider auf der Position MIN, wird kein PortamentoEffekt zugewiesen. Je weiter Sie den Regler zur Position MAX hin bewegen, desto lnger verluft die Tonhhennderung. Sie knnen einen separat erhltlichen Pedalschalter an die PORTAMENTO FOOTSWITCHBuchse anschlieen, um das Portamento ein/auszuschalten.

c . MODE-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[ON, OFF] Aktiviert oder deaktiviert das Portamento, wenn Sie den TRANSPOSEHebel bedienen. Drcken Sie diesen Schalter mit der Spitze eines Stiftes oder einem hnlichen Objekt.

d . TRANSPOSE-Hebel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[2 OCTAVES UP, 0, 2 OCTAVES DOWN] Schaltet den Tonumfang der Tastatur in ZweiOktavenSchritten um.

e . PROPORTIONAL PITCH CONTROL - Pad Proportional zum Druck, den Sie auf das Pad ausben wird die Tonhhe gesenkt.

f . PROPORTIONAL PITCH CONTROL - Pad Proportional zum Druck, den Sie auf das Pad ausben wird Vibrato hinzugefgt.

g . PROPORTIONAL PITCH CONTROL - Pad Proportional zum Druck, den Sie auf das Pad ausben wird die Tonhhe angehoben.

- 43 -

Be di

en un

gs an

le it

un g

Oberseite (VCO 1-Sektion)

c

d e f

h i j

g

a b

Oszillator 1 (VCO1) bietet Ihnen folgende Einstellungsmglichkeiten.

a . FREQUENCY COARSE-Slider (blau) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[20(0 .2)Hz2K(20)Hz] Grobe Tonhhenregelung. Steht der KeyboardSchalter auf ON, betrgt der nderungsbereich der Tonhhe 20 Hz bis 2 kHz, steht er auf OFF, 0,2 Hz bis 20 Hz.

Der Frequenzbereich (20 Hz bis 2 kHz) ist ein Nherungswert.

b . FREQUENCY FINE slider (blau) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [400cent] Feine Tonhhenregelung.

c . Keyboard-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [AUDIO KYBD ON, LF KYBD OFF] Steht der Schalter auf AUDIO KYBD ON, wird VCO1 an das CVKeyboard angeschlossen, so dass Sie damit auf konventionelle Art Tne unterschiedlicher Hhe spielen knnen. Steht der Schalter auf AUDIO KYBD OFF, wird die Verbindung von VCO1 und CVKeyboard getrennt VCO1 oszilliert nunmehr als LFO. Sie knnen dieses Signal zur Modulation von VCO2 oder als Audioquelle fr Soundeffekte nutzen.

d . FM-Tiefe-Slider (rosa) e . FM-Tiefe-Slider (yellow)

Regelt die Tiefe der FM (Frequenzmodulation) falls angewendet.

f . PULSE WIDTH (WIDTH)-Slider (blau) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [50%MIN] Regelt die Impulsbreite.

g . PULSE WIDTH (MOD)-Slider (rosa) Regelt die Tiefe der Impulsbreitenmodulation.

h . FM-Quelle-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [LFO , LFO ] Whlt die Wellenform der vom LFO erzeugten Modulation aus.

i . FM-Quelle-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [S/H, ADSR ] Als Modulationsquelle knnen Sie entweder Sample and Hold oder den Hllkurvengenerator (ADSR) auswhlen.

j . Impulsbreitenmodulationsquelle-Schalter . . . . . . . . . . . . . [LFO , ADSR ] Whlt die Quelle der Impulsbreitenmodulation aus.

ARP ODYSSEY ARP ODYSSEY Module

- 44 -

Oberseite (VCO-2-Sektion)

c

d e f

h i j

g

a b

Oszillator 2 (VCO2) bietet Ihnen folgende Einstellungsmglichkeiten.

a . FREQUENCY COARSE-Slider (grn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[20(0 .2)Hz2K(20)Hz] Grobe Tonhhenregelung. Regelbar im Bereich von 20 Hz bis 2 kHz. Falls der SYNCSchalter eingeschaltet ist, ndern Sie hiermit die Obertonstruktur anstatt der Tonhhe.

Der Frequenzbereich (20 Hz bis 2 kHz) ist ein Nherungswert.

b . FREQUENCY FINE-Slider (green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [400cent] Feine Tonhhenregelung. Falls der SYNCSchalter eingeschaltet ist, ndern Sie hiermit die Obertonstruktur anstatt der Tonhhe.

c . SYNC-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OFF, ON Schaltet die Synchronisierung ein/aus. Ist der Schalter ausgeschaltet, knnen Sie duophonisch spielen. Ist er eingeschaltet, wird VCO2 mit der Frequenz (Tonhhe) von VCO1 synchronisiert.

d . FM-Tiefe-Slider (rosa)

e . FM-Tiefe-Slider (gelb) Regelt die Tiefe der FM (Frequenzmodulation) falls angewendet.

f . PULSE WIDTH (WIDTH)-Slider (blau) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [50%MIN] Regelt die Impulsbreite.

g . PULSE WIDTH (MOD)-Slider (rosa) Regelt die Tiefe der Impulsbreitenmodulation.

h . FM-Quelle-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[LFO , S/H MIXER OR PEDAL] Whlt zwischen der Modulation durch eine LFOSinuswelle oder den S/H MIXER (Sample and Hold Mixer) bzw. ein Pedalsignal. Steht dieser Schalter auf S/H MIXER OR PEDAL, kann die Modulation durch ein separat erhltliches, an die Pedalbuchse angeschlossenes Volumenpedal gesteuert werden.

i . FM-Quelle-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [S/H, ADSR ] Als Modulationsquelle knnen Sie entweder Sample and Hold oder den Hllkurvengenerator (ADSR) auswhlen.

j . Impulsbreitenmodulationsquelle-Schalter . . . . . . . . . . . . . [LFO , ADSR ] Whlt die Quelle der Impulsbreitenmodulation aus.

- 45 -

Be di

en un

gs an

le it

un g

Oberseite (LFO, SAMPLE AND HOLD-Sektion)

a

b c d

e f g

a . LFO FREQ (LFO Geschwindigkeit)-Slider (rosa) . . . . . . . . . . . . . . . . . . . . . . . . . [0 .2Hz20Hz] Regelt die Geschwindigkeit des LFO. Wird der Slider nach oben bewegt, erhht sich die Geschwindigkeit.

b . S/H-Eingangspegel-Slider (blau) Regelt den Pegel, mit dem die vom VCO1 erzeugte Wellenform am Eingang des S/H MIXER anliegt.

c . S/H-Eingangspegel-Slider (wei) Regelt den Pegel, mit dem das vom VCO2 erzeugte Rauschen oder die von diesem erzeugte Rechteckwelle am Eingang des S/H MIXER anliegt.

d . S/H OUTPUT LAG-Slider (gelb) Glttet die nderungen der S/H Ausgangsspannung. Je mehr Sie den Slider zur Position MAX hin bewegen, desto deutlicher fllt die Glttung aus.

e . S/H-Eingangsquelle-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . [VCO-1 , VCO-1 ] Whlt die Quelle (VCO1 Wellenform), die am Eingang des S/H MIXER anliegt.

f . S/H-Eingangsquelle-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[NOISE GEN, VCO-2 ] Whlt die Quelle (Rauschen oder VCO2 Rechteckwelle), die am Eingang des S/H MIXER anliegt.

g . S/H-Triggerquelle-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[LFO TRIG, KYBD TRIG] Whlt das Signal (Ausgabe des LFO oder der Tastatur), das als Trigger dient, wenn ein vom S/H MIXER gesendetes Audiosignal erkannt wird.

ARP ODYSSEY ARP ODYSSEY Module

- 46 -

Oberseite (AUDIO MIXER, VCF, HPF, VCA-Sektion)

d e

f

c

a

g h i j

k l m

n

b

o p q r s t

a . VCF FREQ-Slider (schwarz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [16Hz16KHz] Regelt das Eingreifen des LPF (Low Pass Filters). Befindet sich der Slider in der untersten Position (16 Hz), wird der Hochfrequenzbereich des Eingangssignals beschnitten, was einen weichen Klang erzeugt.. Wird der Slider nach oben bewegt, wird der Sound heller.

b . VCF RESONANCE-Slider (schwarz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[MINSELF OSC] Regelt die Resonanz. Modifiziert die Klangcharakteristik durch Boosten der Obertne im Bereich der CutoffFrequenz. Wenn Sie den Slider hochziehen, beginnt ab einem gewissen Punkt die Selbstoszillation (Zustand, bei dem der VCF eigenstndig einen Klang erzeugt).

c . VCF TYPE-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[ , , ] Whlt den Typ des VCF. : ODYSSEY Rev. 1 : ODYSSEY Rev. 2 : ODYSSEY Rev. 3

d . HPF CUTOFF FREQ-Slider (schwarz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [16Hz16KHz] Regelt das Eingreifen des HPF (High Pass Filters). Wenn Sie den Regler hochziehen, wird der Tieffrequenzbereich des Eingangssignals beschnitten, was einen dnneren Klang erzeugt.. Dies erlaubt Ihnen die Emulation des Klangs bestimmter Instrumente.

e . DRIVE-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[OFF, ON] Hiermit schalten Sie die Verzerrung des VCA ein.

f . VCA GAIN-Slider (schwarz) Regelt die Lautstrke, mit der das Audiosignal durch den VCA geleitet wird.

g . NOISE/RING MOD-Slider (wei) Regelt den Pegel des Audiosignals, das vom Rauschgenerator oder Ringmodulator erzeugt wird.

h . VCO-1-Lautstrke-Slider (blau) Regelt den Pegel des Audiosignals, das vom VCO1 erzeugt wird.

i . VCO-2-Lautstrke-Slider (grn) Regelt den Pegel des Audiosignals, das vom VCO2 erzeugt wird.

j . Filtermodulationspegel-Slider (schwarz) Regelt den Pegel des Signals, das die VCF FREQ steuert oder regelt die Art und Weise, in der das vom S/H MIXER gesendete Signal das Filter ffnet und schliet.

- 47 -

Be di

en un

gs an

le it

un g

k . Filtermodulationspegel-Slider (gelb) Regelt die Art und Weise, in der das Filter vom S/H (Sample and Hold) oder LFO geffnet oder geschlossen wird.

l . Filtermodulationspegel-Slider (rosa) Regelt die Art und Weise, in der die beiden Hllkurvengeneratoren (AR und ADSR) das Filter steuern.

m . VCA-Pegel-Slider (rot) Regelt den Pegel, mit dem die Hllkurvengeneratoren (AR und ADSR) den VCA steuern. Praktisch handelt es sich hierbei um den MasterLautstrkeregler des ARP ODYSSEY. Falls der DRIVESchalter eingeschaltet ist, regeln Sie hiermit auch die Verzerrung des VCA.

n . Filtereingangsquelle (NOISE/RING MOD)-Schalter . . . . . . . . . . [NOISE, RING MOD] Whlt zwischen Rauschen oder Ringmodulator.

o . Filtereingangsquelle (VCO-1 wave)-Schalter . . . .[VCO-1 , VCO-1 ] Whlt die VCO1 Wellenform (Sgezahn oder Rechteck). Falls Sie eine Rechteckwelle ausgewhlt haben, knnen Sie mit dem PULSE WIDTHSlider (Seite 43) die Rechteckwelle in eine Impulswelle umwandeln.

p . Filtereingangsquelle (VCO-2 wave)-Schalter . . . .[VCO-2 , VCO-2 ] Whlt die VCO2 Wellenform (Sgezahn oder Rechteck). Falls Sie eine Rechteckwelle ausgewhlt haben, knnen Sie mit dem PULSE WIDTHSlider (Seite 44) die Rechteckwelle in eine Impulswelle umwandeln.

q . Filtermodulationsquelle (KYBD CV/S/H MIXER OR PEDAL)-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[KYBD CV, S/H MIXER OR PEDAL] Whlt die Quelle, die das Filter steuert. Wenn Sie KYBD CV (KeyboardSteuerspannung) auswhlen, dient das normalerweise zur bermittlung der Tastaturinformationen an den VCO verwendete Signal zum ffnen und Schlieen des Filters. Dies erlaubt Ihnen zum Beispiel Effekte zu erzeugen, bei denen das Filter bei hheren Noten weiter ffnet. Wenn Sie S/H MIXER OR PEDAL auswhlen, ffnet und schliet das vom S/H MIXER gesendete Signal das Filter. Falls Sie ein separat erhltliches Volumenpedal an die PEDALBuchse angeschlossen haben, knnen Sie mit dem Signal des Pedals den VCF steuern und WahWah hnliche Effekte erzeugen.

r . Filtermodulationsquelle (S/H/LFO)-Schalter switch . . . . . . . . . . . . . .[S/H, LFO ] Whlt die Quelle, die das Filter steuert. Einen WahWahEffekt knnen Sie auch erzeugen, indem Sie mit dem LFO das Filter modulieren.

s . Filtermodulationsquelle (ADSR/AR)-Schalter . . . . . . . . . . . . .[ADSR , AR ] Whlt den Hllkurvengenerator, der das Filter steuert.

t . VCA EG-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[AR , ADSR ] Whlt den Hllkurvengenerator, der den VCA steuert.

ARP ODYSSEY ARP ODYSSEY Module

- 48 -

Oberseite (ENVELOPE GENERATOR-Sektion)

c

a

b

d e f

h i j

g

a . AR EG - ATTACK-Slider (rot) Regelt die Anstiegszeit des ARHllkurvengenerators.

b . AR EG - RELEASE-Slider (rot) Regelt die Freigabezeit des ARHllkurvengenerators.

c . Power-LED Leuchtet bei eingeschaltetem Gert und erlischt beim Ausschalten. Bei deaktivierter Energiesparfunktion blinkt beim Einschalten die LED mehrmals, bevor sie dauerhaft leuchtet.

d . ADSR EG - ATTACK-Slider (rot) Regelt die Anstiegszeit des ADSRHllkurvengenerators.

e . ADSR EG - DECAY-Slider (rot) Regelt die Abfallzeit des ADSRHllkurvengenerators.

f . ADSR EG - SUSTAIN-Slider (rot) Regelt die Haltezeit des ADSRHllkurvengenerators.

g . ADSR EG - RELEASE-Slider (rot) Regelt die Freigabezeit des ADSRHllkurvengenerators.

h . ADSR-Triggerquelle-Schalter . . . . . . . . . . . . . . . . . . . . .[KYBD GATE, LFO REPEAT ] Whlt den Trigger, der an den ADSRHllkurvengenerator gesendet wird. Wenn KYBD GATE ausgewhlt ist, wird das Tastatursignal als Trigger zum Hllkurvengenerator gesendet. Wenn LFO REPEAT ausgewhlt ist, wird die Impulswelle des LFO an den Hllkurvengenerator gesendet, der die Hllkurve zyklisch im Tempo der LFO FREQ wiederholt.

i . ADSR-Wiederhol-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [KYBD REPEAT, AUTO REPEAT] Dieser Schalter ist nur wirksam, wenn Sie mit dem ADSR oder AR Triggerquelle Schalter LFO REPEAT ausgewhlt haben. Wenn Sie KYBD REPEAT auswhlen, wird das zum Hllkurvengenerator gesendete LFOTriggersignal solange wiederholt, wie die Taste gedrckt wird. Wenn Sie AUTO REPEAT auswhlen, luft die Wiederholung unabhngig vom Status der Tastatur weiter.

j . AR-Triggerquelle-Schalter . . . . . . . . . . . . . . . . . . . . . . . . . . [KYBD GATE, LFO REPEAT ] Whlt den Trigger, der an den ARHllkurvengenerator gesendet wird. Dieser Schalter hat die gleiche Funktion wie der ADSRTriggerschalter.

- 49 -

Be di

en un

gs an

le it

un g

Rckseite

e f g h i j k l

m n o

b c da

onm

p

k le f g h i jb c da

ARP ODYSSEY Module

ARP ODYSSEY

a . Kabelhaken Wickeln Sie das Kabel des AC Netzteils um diesen Haken, um ein unbeabsichtigtes Lsen der Verbindung zum AC Netzteil zu verhindern.

b . DC 9V-Buchse Schlieen Sie hier ein optionales ACNetzteil an. Schlieen Sie das ACNetzteil erst an dieses Instrument an, bevor Sie den Stecker in die Steckdose stecken.

c . Netzschalter Hiermit schalten Sie das Gert ein und aus. Zum Ein und Ausschalten mssen Sie den Taster eine Weile gedrckt halten.

d . MIDI IN-Anschluss Zum Anschluss und Empfangen von MIDIDaten eines externen MIDIGertes.

e . USB B-Port Zum Anschluss eines Computers und zur bertragung (Senden und Empfangen) von MIDIDaten.

f . PEDAL-Buchse Zum Anschluss eines separat erhltlichen Volumenpedals. Diese Buchse dient auch dem Anschluss eines SQ1 (Sequenzer) zur Steuerung des ARP ODYSSEY.

g . PORTAMENTO FOOTSWITCH-Buchse Zum Anschluss eines separat erhltlichen Pedalschalters.

h . OUTPUT LOW-Buchse Zum Anschluss eines Verstrkers oder eines Aktivlautsprechers.

i . OUTPUT HIGH-Buchse Zum Anschluss eines Mischpults oder eines mit XLRBuchse versehenen Verstrkers.

j . EXT AUDIO INPUT-Buchse Wenn Sie den ARP ODYSSEY als Effektprozessor verwenden, knnen Sie Ihn ber diese Buchse mit einem MonoKlinkenkabel an eine externe Klangquelle anschlieen. Ein externes, an der EXT AUDIO INPUT Buchse anliegendes Signal wird an den AUDIO MIXER weitergeleitet und durch den VCF und VCA gefhrt. Regeln Sie die Lautstrke am angeschlossenen externen Gert. Tipp: Falls Sie mit dem beiliegenden Klinkenkabel die EXT AUDIO INPUT

Buchse mit der Kopfhrerbuchse verbinden, knnen Sie eine Rckkopplung erzeugen und das Klangspektrum des Instruments erweitern. Die Strke der Rckkopplung knnen Sie mit dem Kopfhrerlautstrkeregler einstellen.

k . Kopfhrerlautstrke Regelt die Lautstrke des angeschlossenen Kopfhrers. Falls Sie eine Rckkopplung erzeugt haben, knnen Sie hiermit deren Anteil einstellen.

l . Kopfhrerbuchse Zum Anschluss eines Kopfhrers. Hier liegt dasselbe Signal an wie an den OUTPUT LOW und OUTPUT HIGHBuchsen. Wenn Sie eine Rckkopplung erzeugen wollen, verbinden Sie diese Buchse mit der EXT AUDIO INPUT Buchse des ARP ODYSSEY.

m . CV IN/OUT-Buchsen Ein und Ausgnge fr Steuerspannungen (Spannung, die die Tonhhe bestimmt)

n . GATE IN/OUT-Buchsen Ein und Ausgnge fr Gatesignale (ein Signal fr Klangwiedergabe).

o . TRIG IN/OUT-Buchsen Ein und Ausgnge fr Triggersignale (ein Triggersignal wird durch Drcken einer Taste der Tastatur erzeugt). Tipp: Falls Sie mit dem beiliegenden MiniKlinkenkabel

die TRIG INBuchse mit der GATE OUTBuchse verbinden, wird der ADSRHllkurvengenerator nicht angetriggert, und Sie knnen Legatos spielen.

p . MODE SWITCH (Nur ARP ODYSSEY Module) Satz von 5 Schaltern zur Wahl des MIDIKanals und zum Einstellen der Energiesparfunktion. Werden diese Schalter bedient, blinkt die PowerLED.

Klinkenkabel (beiliegend)

Miniklinkenkabel (beiliegend)

ARP ODYSSEY ARP ODYSSEY Module

- 50 -

Vorbereitung

Anschlsse Nachstehend wird ein typisches Anschlussbeispiel gezeigt. Selbstverstndlich knnen Sie sich auf die fr Sie relevanten Gerte und Anschlsse beschrnken.

Zur Steckdose

AC-Netzteil (Lieferumfang)

Pedalschalter

Monitor, Verstrker etc.

XLR-Kabel

USB-Kabel

Computer

MIDI OUT

Kopfhrer

Volumenpedal Zur externen Klangquelle etc.

MIDI-Kabel Mono- Klinkenkabel

Mono- Klinkenkabel

Mono- Klinkenkabel

oder

Weitere Anschlussbeispiele Sie knnen den ARP ODYSSEY wie folgt beschrieben mit Patchkabeln an einen Sequenzer anschlieen, um mit dem Sequenzer den ARP ODYSSEY anzusteuern. Wenn Sie den ARP ODYSSEY mit einem SQ1 verbinden, verbinden Sie die PEDAL Buchse des ARP ODYSSEY mit der CV OUTBuchse des SQ1, um Tonhhe und Filter des VCO 2 des ARP ODYSSEY zu steuern.

CV OUT

GATE OUT CV IN

GATE IN

CV OUT

Umwandlungs- Stecker

Sequenzer etc.

Schalten Sie alle Gerte vor Herstellen oder Lsen jedweder Anschlsse aus. Veillez mettre tout votre matriel hors tension avant deffectuer la moindre connexion. Der Anschluss eingeschalteter Gerte kann zu Schden an Lautsprechern sowie zu Strungen und Schden an den Gerten selbst fhren.

Wir empfehlen Ihnen, ein separat erhltliches Korg VP10 Volumenpedal zu verwenden und mithilfe eines Klinkenkabels dessen Ausgang OUT 1 oder OUT 2 mit der PEDALBuchse des ARP ODYSSEY zu verbinden Stellen Sie in diesem Fall die Mindestlautstrke (MINIMUM VOLUME) des VP10 auf den Mindestwert 0.

Tipp: Falls Sie das Portamento mit einem Pedalschalter ein/ausschalten wollen, empfehlen wir Ihnen, einen separat erhltlichen Korg PS1 oder PS2 Pedalschalter an die PORTAMENTO FOOTSWITCHBuchse des ARP ODYSSEY anzuschlieen. Wenn Sie das Pedal drcken, schalten Sie das Portamento aus; lassen Sie das Pedal los, wird der PortamentoEffekt in der mit dem PORTAMENTOSlider eingestellen PortamentoZeit zugewiesen.

- 51 -

Be di

en un

gs an

le it

un g

Einschalten Schalten Sie angeschlossene Aktivboxen oder andere externe Verstrker erst ein,

nachdem Sie den ARP ODYSSEY eingeschaltet haben. 1. Stellen Sie den VCAPegelSlider (Seite 47) und den VCA GAINSlider (Seite

46) des ARP ODYSSEY auf den Mindestwert.

2. Drcken Sie den Netzschalter, um den ARP ODYSSEY einzuschalten. Die Power LED leuchtet.

3. Stellen Sie die Lautstrke der Aktivboxen bzw. des externen Verstrkers auf den Mindestwert und schalten Sie sie/ihn ein.

4. Erhhen Sie die Lautstrke der Aktivboxen oder des externen Verstrker auf einen geeigneten Wert und regeln Sie sie anschlieend mit dem VCAPegel Slider des ARP ODYSSEY.

Tipp: Falls Sie wenig Erfahrung im Erstellen von Sounds haben, raten wir Ihnen, die Regler wie im Abschnitt Grundlegende Einstelllungen (Seite 52) beschrieben einzustellen.

Ausschalten 1. Stellen Sie die Lautstrke der Aktivboxen bzw. des externen Verstrkers auf den

Mindestwert und schalten Sie sie/ihn aus.

2. Drcken Sie zum Ausschalten den Netzschalter des ARP ODYSSEY so lange, bis die PowerLED erlischt.

Energiesparfunktion Der ARP ODYSSEY ist mit einer Energiesparfunktion ausgerstet, die das Instrument ausschaltet, wenn es ber etwa vier Stunden hinweg nicht gespielt oder benutzt worden ist. Werksseitig ist die Energiesparfunktion aktiviert.

Deaktivieren der Energiesparfunktion Bei Bedarf knnen Sie die Energiesparfunktion deaktivieren.

Schalten Sie das Instrument beim ndern dieser Einstellung nicht aus. Sonst drohen Datenverluste und Fehlfunktionen.

Tipp: Die Einstellung der Energiesparfunktion wird auch nach dem Ausschalten gespeichert.

Automatische Ausschaltfunktion deaktivieren

ARP ODYSSEY

1. Halten Sie die Tasten C3, D3 und E3 der Tastatur gedrckt und drcken Sie den Netzschalter, um das Instrument einzuschalten.

C3 D3 E3

2. Lassen Sie den Netzschalter erst wieder los, wenn die Power LED nach mehrmaligem Blinken dauerhaft leuchtet. Nun blinkt bei jedem weiteren Einschalten die Power LED und zeigt Ihnen dadurch an, dass die Energiesparfunktion deaktiviert ist.

ARP ODYSSEY Module Schieben Sie den MODE SWITCH 5 auf der Rckseite nach unten. Nun ist die Energiesparfunktion deaktiviert Sie mssen die Einstellung nicht durch Aus und Einschalten besttigen.

Automatische Ausschaltfunktion aktivieren

ARP ODYSSEY

1. Halten Sie die Tasten C3, D3 und E3 der Tastatur gedrckt und drcken Sie den Netzschalter, um das Instrument einzuschalten.

C3 D3 F3

2. Lassen Sie den Netzschalter los, wenn die PowerLED aufleuchtet. Nun leuchtet bei jedem weiteren Einschalten die PowerLED sofort auf und zeigt Ihnen dadurch an, dass die Energiesparfunktion aktiviert ist.

ARP ODYSSEY Module Schieben Sie den MODE SWITCH 5 auf der Rckseite nach oben. Nun ist die Energiesparfunktion aktiviert Sie mssen die Einstellung nicht durch Aus und Einschalten besttigen.

ON

1 2 3 4 5

ON

1 2 3 4 5

ARP ODYSSEY ARP ODYSSEY Module

- 52 -

Erzeugen wir nun ein paar Sounds

Grundlegende Einstellungen Stellen Sie die Regler (Slider, Schalter etc:) des ARP ODYSSEY wie in der Abbildung unten gezeigt ein. Spielen Sie die Tastatur und ziehen Sie dabei langsam den Volumenslider des VCO1 (blau) oder des VCO2 (grn) hoch Sie hren nun den Klang einer Sgezahnwelle. Regeln Sie mit dem VCAPegelSlider (rot) die Lautstrke.

Stimmen Wenn Sie wie beschrieben die grundlegenden Einstellungen vorgenommen haben, sollten Sie mithilfe eines handelsblichen Stimmgerts und durch Regeln der FREQUENCY COURSE und FREQUENCY FINESlider die korrekte Tonhhe einstellen.

- 53 -

Be di

en un

gs an

le it

un g

ber MIDI

MIDI-Gerte anschlieen Wenn Sie den ARP ODYSSEY an einen Computer oder einen externen MIDISequenzer anschlieen, knnen Sie die Klangerzeugung des ARP ODYSSEY extern steuern. Verwenden Sie ein handelsbliches MIDIKabel, um den MIDI INAnschluss des ARP ODYSSEY mit dem MIDI OUTAnschluss des externen MIDIGertes zu verbinden (siehe Anschlsse auf Seite 50). MIDI INBuchse: Hier werden MIDIBefehle von anderen MIDIGerten empfangen. Verbinden Sie diese Buchse mit der MIDI OUTBuchse des anderen Gerts.

Der ARP ODYSSEY kann ber seinen MIDI INAnschluss nur Notennachrichten empfangen, wobei die Anschlagsdynamik ignoriert wird. Es knnen Noten im Bereich von 012 (C0) bis 127 (G9) empfangen werden.

MIDI-Kanal MIDI hat sechzehn Kanle 1 bis 16. Wenn Sie ein externes MIDIGert anschlieen, mssen Sie am ARP ODYSSEY denselben MIDIKanal einstellen wie an Ihrem externen MIDIGert.

Den MIDI-Kanal des ARP ODYSSEY einstellen Den MIDIKanal Ihres ARP ODYSSEY knnen Sie wie folgt einstellen. Werksseitig ist Kanal 1 eingestellt. Tipp: Hinweise zum Einstellen des MIDIKanals Ihres externen Gerts finden Sie in

dessen Bedienungsanleitung.

ARP ODYSSEY

1. Halten Sie die Tasten C3 und C4 der Tastatur gedrckt und drcken Sie den Netzschalter, um das Instrument einzuschalten. Nun befindet sich der ARP ODYSSEY im MIDIKanalEinstellmodus und die Power LED zeigt durch Blinken* den aktuellen MIDIKanal an.

C3 C4

* Blinkt die LED wiederholt einmal, ist MIDI Kanal 1 eingestellt, blinkt sie wiederholt zweimal, Kanal 2 usw.

2. Die MIDIKanle (116) sind der Tastatur wie folgt zugewiesen. Drcken Sie die dem gewnschten MIDIKanal entsprechende Taste (z. B. D2 fr Kanal 2) Die PowerLED blinkt entsprechend.*

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

3. Drcken Sie die Taste C6, um den eingestellten MIDIKanal zu speichern. Nach dem Speichern schaltet sich das Gert aus.

C6

ARP ODYSSEY Module

Mit MODE SWITCH 14 auf der Rckseite whlen Sie den MIDIKanal. Die MIDI KanalEinstellungen sind in der folgenden Tabelle aufgefhrt. Der MIDIKanal ndert sich, sobald Sie die Einstellung ndern.

Sie knnen den MIDIKanal auch whrend des Betriebs ndern, dadurch werden aber aktuell wiedergegebene Noten abgeschaltet. Der Pitch Bend wird ebenfalls zurckgesetzt.

1 ON

1 2 3 4

2 ON

1 2 3 4

3 ON

1 2 3 4

4 ON

1 2 3 4

5 ON

1 2 3 4

6 ON

1 2 3 4

7 ON

1 2 3 4

8 ON

1 2 3 4

9 ON

1 2 3 4

10 ON

1 2 3 4

11 ON

1 2 3 4

12 ON

1 2 3 4

13 ON

1 2 3 4

14 ON

1 2 3 4

15 ON

1 2 3 4

16 ON

1 2 3 4

ARP ODYSSEY ARP ODYSSEY Module

- 54 -

Computer anschlieen Sie knnen den ARP ODYSSEY anstatt ber den MIDIAnschluss auch direkt per USBKabel an den USBPort Ihres Computers anschlieen, um MIDINachrichten zu empfangen (siehe Anschlsse auf Seite 50). Die MIDINachrichten, die per USBPort gesendet und empfangen werden knnen, sind auf 1 festgelegt: es knnen Notennachrichten (mit festem VelocityWert von 64 beim Senden und ignorierter Anschlagsdynamik beim Empfangen) gesendet und empfangen werden. Da der ARP ODYSSEY Module keine Tastatur besitzt, kann er keine NotenNachrichten senden. Der ARP ODYSSEY Module kann MIDI Pitch BendNachrichten empfangen (2 Halbtnen). Tipp: Es knnen lediglich mit dem Keyboard erstellte MIDINotenbefehle gesendet

werden. Nachrichten wie PROPORTIONAL PITCH CONTROL werden nicht gesendet.

Tipp: Eine USBVerbindung erfordert die Installation des KORG USBMIDI Treibers. Laden Sie den KORG USBMIDITreiber von der Korg Website ( http://www.korg.com/ ) herunter und installieren Sie diesen laut den dem Treiber beigefgten Anweisungen.

ber die MIDI-Implementationstabelle In der MIDIImplementationstabelle finden Sie die MIDINachrichten, die gesendet und empfangen werden knnen. Wenn Sie ein MIDIGert verwenden, berprfen Sie anhand der MIDIImplementationstabellen, ob die MIDINachrichten kompatibel sind. Die MIDIImplementationstabelle fr dieses Gert steht unter der KorgWebsite zum Download bereit. Tipp: Fr Einzelheiten zur MIDINorm siehe MIDIImplementation. Fr

Einzelheiten zur MIDIImplementation besuchen Sie die Korg Website. http://www.korg.com/

Fehlersuche Das Gert lsst sich nicht einschalten . Ist das AC Netzteil korrekt angeschlossen?

Es ist nichts zu hren . Versuchen Sie, die Regler wie in Abschnitt Grundlegende Einstellungen (Seite

52) beschrieben einzustellen. Haben Sie den ARP ODYSSEY korrekt an den Eingang Ihres Verstrkers,

Mischpults oder Kopfhrers angeschlossen? Haben Sie den Verstrker oder das Mischpult eingeschaltet und dessen Lautstrke

aufgedreht?

Steht der VCAPegelSlider (rot, Seite 47) oder der VCA GAINSlider (schwarz, Seite 46) mglicherweise auf 0?

Keine Reaktion auf von einem externen Gert gesendete MIDI-Daten . Haben Sie das MIDI oder USBKabel korrekt angeschlossen? (Seite 50). Entspricht der MIDIKanal, auf dem das externe MIDIGert die Daten sendet,

dem globalen MIDIKanal des ARP ODYSSEY? (siehe MIDIKanal auf Seite 53).

Der Klang einer externen Audioquelle kann nicht wiedergegeben oder bearbeitet werden . Haben Sie die Klangquelle korrekt an die EXT AUDIO INPUTBuchse auf der Rckseite

angeschlossen?

Der Pitch Bend am ARP ODYSSEY Module kann nicht zurckgesetzt werden . Der Pitch Bend wird durch den Empfang einer MIDINachricht wie z. B. Reset

All Controllers zurckgesetzt. Falls Sie ihn direkt am Gert zurcksetzen wollen, schalten Sie es einfach kurz aus und wieder ein, oder ndern Sie mit einem MODE SWITCH vorbergehend den MIDIKanal.

Technische Daten Betriebstemperatur: 0 +40 C (ohne Kondensbildung) Tastatur (Nur ARP ODYSSEY): 37 Noten (Slimkey, keine Anschlagsdynamik, kein

Aftertouch) Maximale: Polyphonie 2 Stimmen fr Duophonie,

normalerweise monophonisch REGLER

Transpositionen: 2 Oktaven tiefer, normal, 2 Oktaven hher Proportional Pitch Control: (Pitch down) Pad: etwa2/3 Oktave (Modulation) Pad (Pitch up) Pad: etwa2/3 Oktave

Rauschgenerator: Rauscharten (wei und rosa) Portamento: Maximum speed: about 0.01 msec./oct

Maximale Geschwindigkeit: etwa 0,01 msek/Okt. VCO (Voltage Controlled Oscilator)

Wellenformen: Sgezahn, Rechteck, Impuls (dynamischer Impuls) Frequenzbereich: VCO1 im Niederfrequenzmodus, 0,2 Hz 20 Hz:

VCO1 und VCO2 (hrbarer Bereich) etwa 20 Hz 20 kHz

- 55 -

Be di

en un

gs an

le it

un g

Abweichung in der Aufwrmphase: Maximal 1/30 Halbton ab Einschalten Impulsbreite: 50 % 5 % Impulsbreitenmodulation: ADSR, +45 %; LFO, +15 % Steuerspannung: 1 V/Okt. Maximale Frequenzverschiebungen: LFOSinuswelle: +1/2 Okt. / LFORechteckwelle:

+1,5 Okt. / ADSR: +9 Okt. / S/H:, +2 Okt. VCO1 hat LowNotePrioritt, VCO2 hat HighNotePrioritt.

VCF (Voltage Controlled Filter) Typen: Low pass (I: 12 dB/Okt. / II III: 24 dB/Okt.) Frequenzumfang: 16 Hz 16 kHz Maximal nutzbare Q: 30 Resonanz: 1/2 Selbstoszillation Steuerspannung: Taste C3 (ganz links): 0 V, Taste C6 (ganz rechts) 3 V

VCA (Voltage Controlled Amplifier) Dynamikumfang: 80 dB

RINGMODULATOR Typ: Digital Eingangssignal: VCO1, VCO2 (Rechteckwelle)

SAMPLE & HOLD Steuerquellen: Tastatur oder LFOTrigger Gesampelte Signale: VCO1 Sgezahn und Rechteckwelle, VCO2

Rechteckwelle und Rosa Rauschen. ADSRHLLKURVENGENERATOR

Anstiegszeit: 5 msec. 5 sec. Abfallzeit: 10 msec. 8 sec. Haltepegel: 0 100 % oder Peak Freigabezeit: 15 msec. 10 sec.

ARHLLKURVENGENERATOR Anstiegszeit: 5 msec. 5 sec. Freigabezeit: 10 msec. 8 sec.

STEUEREINGNGE Pedal: 6,3mmMono-Klinkenbuchse PortamentoFuschalter: 6,3mmMono-Klinkenbuchse

AUDIOAUSGNGE LOW Anschluss: 6,3mmMono-Klinkenbuchse MaximalerAusgangspegel: -20dBu@10kLast

Ausgangsimpedanz: 10k HIGH Anschluss: XLRAnschluss MaximalerAusgangspegel: +4dBu@1kLast Ausgangsimpedanz: 330

KOPFHRERANSCHLUSS Anschluss: 6,3mmStereo-Klinkenbuchse MaximalerAusgangspegel: 50mW+50mW@33Last Ausgangsimpedanz: 10 * Steuerbar mit Lautstrkeregler.

EXTERNER AUDIOEINGANG (EXT AUDIO INPUT) Anschluss: 6,3mmMono-Klinkenbuchse Maximaler Eingangspegel: 10 dBu Eingangsimpedanz: 22k

MIDIAnschluss: IN USBAnschluss: Typ B CV IN/OUTBuchsen

Steuerspannung Tastatur (IN/OUT): 1 V/Okt. Anschluss: 3,5mmMono-Klinkenbuchse

GATE IN/OUTBuchsen GATE IN: +3 V (Minimum) GATE OUT: +10 V, Taste gedrckt / 0 V alle Tasten oben Anschluss: 3,5mmMono-Klinkenbuchse

TRIG IN/OUTBuchsen TRIGGER IN: +3 V Impuls min., 10 sec. Mindestdauer TRIGGER OUT: +10 V Impuls bei Tastendruck, 10 sec. Dauer Anschluss: 3,5mmMono-Klinkenbuchse

Stromversorgung: ACNetzgertbuchse (DC 9 V ) Leistungsaufnahme: 6,5 W Abmessungen (B x T x H), Gewicht:

ARP ODYSSEY 502 x 380 x 120 mm, 5 kg ARP ODYSSEY Module 496 x 265 x 89 mm, 3,7 kg

Lieferumfang: ACNetzteil, Klinkenkabel, MiniKlinkenkabel, Bedienungsanleitung

Zubehr: VP10 Volumenpedal, PS1/PS3 Pedalschalter

* nderungen der technischen Daten und des Designs ohne vorherige Ankndigung vorbehalten.

- 57 -

M an

ua l d

e us

ua ri

o

Gracias por adquirir el sintetizador duofnico ODYSSEY/ODYSSEY Module de ARP. Para garantizar el disfrute sin problemas, lea cuidadosamente este manual y utilice este producto correctamente.

Precauciones Ubicacin El uso de la unidad en las siguientes ubicaciones puede dar como resultado un mal funcionamiento: Expuesto a la luz directa del sol Zonas de extremada temperatura o humedad Zonas con exceso de suciedad o polvo Zonas con excesiva vibracin Cercano a campos magnticos

Fuente de alimentacin Por favor, conecte el adaptador de corriente designado a una toma de corriente con el voltaje adecuado. No lo conecte a una toma de corriente con voltaje diferente al indicado.

Interferencias con otros aparatos Las radios y televisores situados cerca pueden experimentar interferencias en la recepcin. Opere este dispositivo a una distancia prudencial de radios y televisores.

Manejo Para evitar una rotura, no aplique excesiva fuerza a los conmutadores o controles.

Cuidado Si exterior se ensucia, lmpiese con un trapo seco. No use lquidos impiadores como disolvente, ni compuestos inflamables.

Guarde este manual Despus de leer este manual, gurdelo para futuras consultas.

Mantenga los elementos externos alejados del equipo Nunca coloque ningn recipiente con lquido cerca de este equipo, podra causar un cortocircuito, fuero o descarga elctrica. Cuide de que no caiga ningn objeto metlico dentro del equipo.

* Todos los nombres de productos y compaas son marcas comerciales o marcas registradas de sus respectivos propietarios.

Nota respecto a residuos y deshechos (solo UE) Cuando aparezca el smbolo del cubo de basura tachado sobre un producto, su manual de usuario, la batera, o el embalaje de cualquiera de stos, significa que cuando quiere tire dichos artculos a la basura, ha de hacerlo en acuerdo con la normativa vigente de la Unin Europea. No debe verter dichos artculos junto con la basura de casa. Verter este producto de manera adecuada ayudar a evitar daos a su salud pblica y posibles daos al medioambiente. Cada pas tiene una normativa especfica acerca de cmo verter productos potencialmente txicos, por

tanto le rogamos que se ponga en contacto con su oficina o ministerio de medioambiente para ms detalles. Si la batera contiene metales pesados por encima del lmite permitido, habr un smbolo de un material qumico, debajo del smbolo del cubo de basura tachado.

NOTA IMPORTANTE PARA EL CONSUMIDOR Este producto ha sido fabricado de acuerdo a estrictas especificaciones y requerimientos de voltaje aplicables en el pas para el cual est destinado. Si ha comprado este producto por internet, a travs de correo, y/o venta telefnica, debe usted verificar que el uso de este producto est destinado al pas en el cual reside. AVISO: El uso de este producto en un pas distinto al cual est destinado podra resultar peligroso y podra invalidar la garanta del fabricante o distribuidor. Por favor guarde su recibo como prueba de compra ya que de otro modo el producto puede verse privado de la garanta del fabricante o distribuidor.

ARP ODYSSEY ARP ODYSSEY Module

- 58 -

Introduccin al ODYSSEY

Qu es el ODYSSEY? ARP Corporation fabric el ODYSSEY entre 1972 y 1981, y fue uno de sus productos ms conocidos. En trminos generales, existen tres versiones en funcin de su fecha de produccin, y su aspecto, carcter tonal y funciones varan. El modelo 2800 se conoce como Rev. 1; incluye el modelo de panel blanco inicial producido entre 1972 y 1974 y el modelo de panel negro producido entre 1974 y aproximadamente 1975. Los modelos 2810 2813 se conocen como Rev. 2; incluyen los modelos de panel negro producidos entre 1975 y aproximadamente 1976. Se realizaron cambios en el filtro, y tambin en el oscilador de algunos de los modelos. Tambin se aadieron la entrada de audio externa y los jacks de entrada CV/GATE, y en los modelos posteriores el modulador de la afinacin de tipo mando se cambi a PPC (control de afinacin proporcional). Los modelos 2820 2823 se conocen como Rev. 3; se produjeron entre 1978 y aproximadamente 1981. El panel se cambi a un panel negro con serigrafa naranja, y el diseo tambin se modific considerablemente respecto a los modelos 2800 2813. La salida de audio tambin se cambi de RCA/PHONE a los jacks XLR/PHONE.

Caractersticas principales La circuitera del VCO, VCF y VCA analgica tradicional del ARP ODYSSEY.

Proporciona un alto grado de espontaneidad de la edicin de sonido que se ofrece de forma exclusiva mediante la sntesis analgica.

Soporte de teclado delgado de 37 notas que abarca la gama de afinacin de siete octavas. [El ARP ODYSSEY Module es un modelo sin teclado.]

Puede reproducir el instrumento de forma monofnica, o bien utilizar el modo duofnico que reproduce los osciladores en afinaciones independientes al reproducir dos teclas simultneamente. (Sin embargo, solo existe un filtro y un amplificador).

Se proporcionan dos tipos de generadores de envolventes: tipo ADSR y tipo AR. Sincronizacin del oscilador. Esta caracterstica es importante para generar

numerosos armnicos superiores de frecuencias altas y debido a su nitidez. Se ha reproducido el PPC (control de afinacin proporcional) utilizando el pad de

goma original. La modulacin se puede aplicar de numerosas formas. Se proporcionan dos tipos de ruido. Se proporcionan LFO y S&H, y puede cambiar su enrutamiento. Se proporcionan los filtros de los tres tipos distintos de ARP ODYSSEY, que se

pueden seleccionar con un conmutador nico.

Tabla de contenido

Introduccin al ODYSSEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Qu es el ODYSSEY? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Caractersticas principales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Diagrama de bloques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Descripcin y funciones de los paneles . . . . . . . . . . . . . . . . . . . . . . 60

Panel frontal (tipo de ruido, seccin de controlador) . . . . . . . . . . . . . . . . . . . . . . . . . 60 Panel frontal (seccin VCO-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Panel frontal (seccin VCO-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Panel frontal (seccin LFO, SAMPLE AND HOLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Panel frontal (seccin AUDIO MIXER, VCF, HPF, VCA) . . . . . . . . . . . . . . . . . . . . . . . . . 64 Panel frontal (seccin ENVELOPE GENERATOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Panel posterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Primeros pasos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Conexiones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Activar el equipo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Desactivar el equipo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Funcin de desactivacin automtica . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Creacin de sonidos de ejemplo . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Ajustes bsicos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Afinacin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Acerca de MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Conexin de dispositivos MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Conexin de un ordenador . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Acerca de la tabla de implementacin MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Solucin de problemas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Especificaciones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Este manual explica el ARP ODYSSEY y el ARP ODYSSEY Module. Si no se especifica lo contrario, las ilustraciones del panel corresponden al ARP ODYSSEY.

- 59 -

M an

ua l d

e us

ua ri

o

Gracias al jack de entrada de audio externa que se proporciona, tambin puede procesar el sonido de un instrumento musical externo.

Se proporcionan un puerto USB y conectores MIDI, que le permiten conectar un PC o un instrumento MIDI.

Diagrama de bloques

NOISE GENERATOR

AUDIO MIXER

VOLTAGE CONTROLLED

FILTER

HIGH PASS

FILTER

VOLTAGE CONTROLLED

AMPLIFIER

RING MOD

SAMPLE AND

HOLD

SAMPLE AND HOLD

MIXER

VOLTAGE CONTROLLED OSCILLATORS

LOW FREQUENCY OSCILLATOR

PEDAL ADSR AND AR

ENVELOPE GENERATORS

TRIGGER

ARP ODYSSEY Module: Solo entrada MIDI (MIDI IN)

KEYBOARD

MIDI IN

ARP ODYSSEY: Teclado incorporado y entrada MIDI (MIDI IN)

ARP ODYSSEY ARP ODYSSEY Module

- 60 -

Descripcin y funciones de los paneles

Panel frontal (tipo de ruido, seccin de controlador)

a

b c

d

e f g

a . Conmutador NOISE GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [WHITE, PINK] Selecciona el ruido blanco o el ruido rosa.

b . Deslizador PORTAMENTO (negro) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[MINMAX] Especifica cmo se aplica el efecto de portamento (el tiempo durante el que se produce el cambio de afinacin). Si el deslizador est en la posicin MIN, no se aplica ningn efecto de portamento. Al desplazar el deslizador hacia la posicin MAX, el cambio de afinacin se produce durante un periodo ms largo. Si hay una pedalera opcional (se vende por separado) conectada al jack PORTAMENTO FOOTSWITCH, se puede utilizar para activar/desactivar el portamento.

c . Conmutador MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[ON, OFF] Selecciona si el portamento est activado al utilizar la palanca TRANSPOSE. Utilice un bolgrafo de punta final o un objeto similar para presionar este conmutador.

d . Palanca TRANSPOSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[2 OCTAVES UP, 0, 2 OCTAVES DOWN] Cambia la gama de afinaciones asignadas al teclado en pasos de dos octavas.

e . PROPORTIONAL PITCH CONTROL - Pad La afinacin se reduce en funcin de la fuerza con la que se presiona el pad.

f . PROPORTIONAL PITCH CONTROL - Pad El vibrato se aplica en funcin de la fuerza con la que se presiona el pad.

g . PROPORTIONAL PITCH CONTROL - Pad La afinacin aumenta en funcin de la fuerza con la que se presiona el pad.

- 61 -

M an

ua l d

e us

ua ri

o

Panel frontal (seccin VCO-1)

c

d e f

h i j

g

a b

Los ajustes siguientes corresponden al oscilador 1 (VCO1).

a . Deslizador FREQUENCY COARSE (azul) . . . . . . . . . . . . . . . . . . . . . . . .[20(0 .2)Hz2K(20)Hz] Ajuste aproximado de la afinacin. Este ajuste abarca la gama de 20 Hz 2 kHz si el conmutador del teclado est activado, o de 0,2 Hz 20 Hz si el conmutador del teclado est desactivado.

La gama de frecuencias (20 Hz 2 kHz) es un valor aproximado.

b . Deslizador FREQUENCY FINE (azul) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [400cent] Ajuste preciso de la afinacin.

c . Conmutador del teclado . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [AUDIO KYBD ON, LF KYBD OFF] Si se ajusta en AUDIO KYBD ON, VCO1 est conectado al CV del teclado y producir afinaciones de forma convencional. Si se ajusta en AUDIO KYBD OFF, VCO1 est desconectado del CV del teclado y oscilar como un LFO. Puede utilizar esta seal para modular VCO2 o como una fuente de audio para efectos de sonido.

d . Deslizador de profundidad de FM (rosa) e . Deslizador de profundidad de FM (amarillo)

Ajusta la profundidad de FM (modulacin de frecuencia) cuando se aplica.

f . Deslizador PULSE WIDTH (WIDTH) (azul) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [50%MIN] Ajusta la amplitud del impulso.

g . Deslizador PULSE WIDTH (MOD) (pink) Ajusta la profundidad de la modulacin de la amplitud del impulso.

h . Conmutador de fuente de FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [LFO , LFO ] Selecciona la forma de onda de la modulacin aplicada por el LFO.

i . Conmutador de fuente de FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [S/H, ADSR ] Selecciona la opcin de muestreo y retencin o el generador de envolvente (ADSR) como la fuente de modulacin.

j . Conmutador de fuente de modulacin de amplitud del impulso . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [LFO , ADSR ] Selecciona la fuente que aplicar la modulacin de amplitud del impulso.

ARP ODYSSEY ARP ODYSSEY Module

- 62 -

Panel frontal (seccin VCO-2)

c

d e f

h i j

g

a b

Los ajustes siguientes corresponden al oscilador 2 (VCO2).

a . Deslizador FREQUENCY COARSE (verde) . . . . . . . . . . . . . . . . . . . . . .[20(0 .2)Hz2K(20)Hz] Ajuste aproximado de la afinacin. Se puede ajustar en la gama de 20 Hz 2 kHz. Si el conmutador SYNC est activado, cambia la estructura de armnicos superiores en lugar de la afinacin.

La gama de frecuencias (20 Hz 2 kHz) es un valor aproximado.

b . Deslizador FREQUENCY FINE (verde) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [400cent] Ajuste preciso de la afinacin. Si el conmutador SYNC est activado, cambia la estructura de armnicos superiores en lugar de la afinacin.

c . Conmutador SYNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[OFF, ON] Activa/desactiva la sincronizacin. Si est desactivado, se permite la interpretacin duofnica. Si est activado, VCO 2 se sincroniza con la frecuencia (afinacin) de VCO1.

d . Deslizador de profundidad de FM (rosa) e . Deslizador de profundidad de FM (amarillo)

Ajusta la profundidad de FM (modulacin de frecuencia) cuando se aplica.

f . Deslizador PULSE WIDTH (WIDTH) (azul) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [50%MIN] Ajusta la amplitud del impulso.

g . Deslizador PULSE WIDTH (MOD) (pink) Ajusta la profundidad de la modulacin de la amplitud del impulso.

h . Conmutador de fuente de FM . . . . . . . . . . . . . . . . . . .[LFO , S/H MIXER OR PEDAL] Selecciona la modulacin por una onda sinusoidal de LFO o por el S/H MIXER (mezclador de muestreo y retencin), o bien por la seal de pedal. Si selecciona S/H MIXER OR PEDAL, la modulacin se puede controlar mediante un pedal de volumen opcional (se vende por separado) conectado al jack de pedal.

i . Conmutador de fuente de FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [S/H, ADSR ] Selecciona la opcin de muestreo y retencin o el generador de envolvente (ADSR) como la fuente de modulacin.

j . Conmutador de fuente de modulacin de amplitud del impulso . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [LFO , ADSR ] Selecciona la fuente que aplicar la modulacin de amplitud del impulso.

- 63 -

M an

ua l d

e us

ua ri

o

Panel frontal (seccin LFO, SAMPLE AND HOLD)

a

b c d

e f g

a . Deslizador LFO FREQ (velocidad del LFO) (rosa) . . . . . . . . . . . . . . . . . . . . . . . [0 .2Hz20Hz] Ajusta la velocidad del LFO. Al elevar el deslizador la velocidad aumenta.

b . Deslizador de nivel de entrada S/H (azul) Ajusta el nivel al que la salida de forma de onda desde VCO1 se recibe en el S/H MIXER.

c . Deslizador de nivel de entrada S/H (blanco) Ajusta el nivel al que la salida de ruido o de forma de onda cuadrada desde VCO 2 se recibe en el S/H MIXER.

d . Deslizador S/H OUTPUT LAG (amarillo) Suaviza los cambios del voltaje de salida de S/H. Al desplazar el deslizador hacia la posicin MAX, se aplicar una cantidad mayor del suavizado.

e . Conmutador de fuente de entrada S/H . . . . . . . . . . . . [VCO-1 , VCO-1 ] Selecciona la fuente (forma de onda de VCO1) que se recibe en el S/H MIXER.

f . Conmutador de fuente de entrada S/H . . . . . . . . . . . . . . . . .[NOISE GEN, VCO-2 ] Selecciona la fuente (ruido o forma de onda cuadrada de VCO2) que se recibe en el S/H MIXER.

g . Conmutador de fuente de disparador S/H . . . . . . . . . . . . . . . . . . .[LFO TRIG, KYBD TRIG] Selecciona la seal (la salida del LFO o la salida del teclado) que se utiliza como el disparador al detectar una seal de audio enviada desde el S/H MIXER.

ARP ODYSSEY ARP ODYSSEY Module

- 64 -

Panel frontal (seccin AUDIO MIXER, VCF, HPF, VCA)

d e

f

c

a

g h i j

k l m

n

b

o p q r s t

a . Deslizador VCF FREQ (negro) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [16Hz16KHz] Ajusta cmo se aplica el LPF (filtro de paso bajo). Si el deslizador est en la posicin ms baja (16 Hz), se corta la gama de frecuencias altas de la seal de entrada, produciendo un sonido suave. Al elevar el deslizador aumenta la viveza del sonido.

b . Deslizador VCF RESONANCE (negro) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[MINSELF OSC] Ajusta la resonancia. Esto modifica el carcter tonal al elevar los armnicos superiores en la regin del punto de corte. Al elevar el deslizador, se producir la oscilacin automtica (estado en el que el propio VCF produce un sonido) a partir de un determinado punto.

c . Conmutador VCF TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[ , , ] Selecciona el tipo de VCF. : ODYSSEY Rev. 1 : ODYSSEY Rev. 2 : ODYSSEY Rev. 3

d . Deslizador HPF CUTOFF FREQ (negro) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [16Hz16KHz] Ajusta cmo se aplica el HPF (filtro de paso alto). Al elevar el deslizador, se corta la regin de frecuencias bajas de la seal de entrada, produciendo un sonido ms fino. Esto es til para simular el sonido de algunos instrumentos.

e . Conmutador DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[OFF, ON] Al activarlo, puede realizar la distorsin del VCA.

f . Deslizador VCA GAIN (negro) Ajusta el volumen al que la seal de audio siempre recorre el VCA.

g . Deslizador NOISE/RING MOD (blanco) Ajusta el nivel de la seal de audio que se enva desde el generador de ruido o el modulador en anillo.

h . Deslizador de volumen VCO-1 (azul) Ajusta el nivel de la seal de audio que se enva desde VCO1.

i . Deslizador de volumen VCO-2 (verde Adjusts the level of the audio signal that is sent from VCO2.

j . Deslizador de nivel de modulacin de filtro (negro) Ajusta el nivel de la seal que controla el VCF FREQ, o ajusta cmo la seal enviada desde el S/H MIXER abre y cierra el filtro.

- 65 -

M an

ua l d

e us

ua ri

o

k . Deslizador de nivel de modulacin de filtro (amarillo) Ajusta cmo S/H (muestreo y retencin) o el LFO abre y cierra el filtro.

l . Deslizador de nivel de modulacin de filtro (rosa) Ajusta cmo los dos generadores de envolventes (AR y ADSR) controlan el filtro.

m . Deslizador de nivel de VCA (rojo) Ajusta el nivel en el que los generadores de envolventes (AR y ADSR) controlan el VCA. En la prctica, se trata del volumen general del ARP ODYSSEY. Si el conmutador DRIVE est activado, tambin ajusta la distorsin de VCA.

n . Conmutador de fuente de entrada de filtro (NOISE/RING MOD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [NOISE, RING MOD] Selecciona el ruido o el modulador en anillo.

o . Conmutador de fuente de entrada de filtro (VCO-1 wave) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[VCO-1 , VCO-1 ] Selecciona la forma de onda de VCO1 (sierra o cuadrada). Si selecciona la onda cuadrada, puede elevar el deslizador PULSE WIDTH (pgina 61) para cambiar de una onda cuadrada a una onda de impulso.

p . Conmutador de fuente de entrada de filtro (VCO-2 wave) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[VCO-2 , VCO-2 ] Selecciona la forma de onda de VCO2 (sierra o cuadrada). Si selecciona la onda cuadrada, puede elevar el deslizador PULSE WIDTH (pgina 62) para cambiar de una onda cuadrada a una onda de impulso.

q . Conmutador de fuente de modulacin de filtro (KYBD CV/S/H MIXER OR PEDAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[KYBD CV, S/H MIXER OR PEDAL] Selecciona la fuente que controlar el filtro. Si selecciona KYBD CV (voltaje de control del teclado), la seal que se suele utilizar para transmitir la informacin de tecla desde el teclado al VCO se puede utilizar para abrir y cerrar el filtro. Por ejemplo, puede producir un efecto en el que el filtro se abre ms para notas ms altas. Si selecciona S/H MIXER OR PEDAL, la seal enviada desde el S/H MIXER abrir y cerrar el filtro. Si hay conectado un pedal de volumen opcional (se vende por separado) al jack PEDAL, puede utilizar la seal del pedal para controlar el VCF, produciendo un efecto como un pedal de wah.

r . Conmutador de fuente de modulacin de filtro (S/H/LFO) . .[S/H, LFO ] Selecciona la fuente que controlar el filtro. Puede producir un efecto de wah utilizando el LFO para modular el filtro.

s . Conmutador de fuente de modulacin de filtro (ADSR/AR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[ADSR , AR ] Selecciona el generador de envolvente que controlar el filtro.

t . Conmutador VCA EG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[AR , ADSR ] Selecciona el generador de envolvente que controlar el VCA.

ARP ODYSSEY ARP ODYSSEY Module

- 66 -

Panel frontal (seccin ENVELOPE GENERATOR)

c

a

b

d e f

h i j

g

a . Deslizador AR EG - ATTACK (rojo) Ajusta el tiempo de ataque del generador de envolvente de AR.

b . Deslizador AR EG - RELEAS (rojo) Ajusta el tiempo de liberacin del generador de envolvente de AR.

c . LED de alimentacin Se enciende si la alimentacin est activada, y se apaga si la alimentacin est desactivada. Si la funcin de desactivacin automtica est desactivada, el LED parpadea varias veces y despus permanece encendido al activar la alimentacin.

d . Deslizador ADSR EG - ATTACK (rojo) Ajusta el tiempo de ataque del generador de envolvente de ADSR.

e . Deslizador ADSR EG - DECAY (rojo) Ajusta el tiempo de cada del generador de envolvente de ADSR.

f . Deslizador ADSR EG - SUSTAIN (rojo) Ajusta el tiempo de sustain del generador de envolvente de ADSR.

g . Deslizador ADSR EG - RELEASE (rojo) Ajusta el tiempo de liberacin del generador de envolvente de ADSR.

h . Conmutador de fuente de disparador ADSR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [KYBD GATE, LFO REPEAT ] Selecciona el disparador que se enva al generador de envolvente de ADSR. Si KYBD GATE est seleccionado, el disparador enviado desde el teclado se enva al EG. Si LFO REPEAT est seleccionado, la onda de impulso del LFO se enva al EG, y el EG repite la envolvente de forma cclica con la proporcin del LFO FREQ.

i . Conmutacin de repeticin de ADSR . . . . . . . . . . . . . . [KYBD REPEAT, AUTO REPEAT] No tiene efecto si el conmutador de fuente de disparador ADSR o AR ha seleccionado LFO REPEAT. Si KYBD REPEAT est seleccionado, el disparador del LFO enviado de forma repetida al EG contina repitindose nicamente mientras la tecla est pulsada. Si AUTO REPEAT est seleccionado, contina repitindose independientemente del estado activado/desactivado del teclado.

j . Conmutador de fuente de disparador AR . [KYBD GATE, LFO REPEAT ] Selecciona el disparador que se enva al generador de envolvente de AR. Tiene la misma funcin que el conmutador de disparador ADSR.

- 67 -

M an

ua l d

e us

ua ri

o

Panel posterior

e f g h i j k l

m n o

b c da

onm

p

k le f g h i jb c da

ARP ODYSSEY Module

ARP ODYSSEY

a . Gancho para cable Enrolle el cable del adaptador de CA en torno a este gancho para evitar que el adaptador de CA se desconecte accidentalmente.

b . Jack DC 9V Conecte el adaptador de CA incluido aqu. Primero conecte el adaptador de CA a este instrumento, y luego conecte el enchufe a una toma de CA.

c . Conmutador de alimentacin Permite activar o desactivar el equipo. Para activar el equipo, mantenga pulsado el conmutador.

d . Conector MIDI IN Puede conectar un dispositivo MIDI externo a este conector para recibir datos MIDI.

e . Puerto USB B Puede conectar un ordenador a este puerto para transmitir y recibir datos MIDI.

f . Jack PEDAL Conecte un pedal de volumen opcional (se vende por separado) aqu. Tambin utilizar este jack al conectar el SQ1 (secuenciador) para controlar el ARP ODYSSEY.

g . Jack PORTAMENTO FOOTSWITCH Conecte una pedalera opcional (se vende por separado) aqu.

h . Jack OUTPUT LOW Conecte un amplificador o un altavoz de monitor autoalimentado aqu.

i . Jack OUTPUT HIGH Aqu puede conectar un mezclador o un amplificador equipado con un jack XLR.

j . Jack EXT AUDIO INPUT Si utiliza el ARP ODYSSEY como un procesador de efectos, utilice un cable phone mono para conectar su fuente de audio externa a este jack. Una fuente externa que se recibe en el jack EXT AUDIO INPUT se recibe en el AUDIO MIXER y recorre el VCF y el VCA. Utilice el dispositivo externo conectado para ajustar el volumen. SUGERENCIA: Si utiliza el cable de jack phone incluido para conectar el jack

EXT AUDIO INPUT al jack de auriculares, se puede aplicar la retroalimentacin automtica, que ampla la gama de sonidos. Utilice el volumen de los auriculares para ajustar la cantidad de retroalimentacin.

k . Volumen de auriculares Ajusta el volumen de los auriculares conectados. Si se aplica la auto retroalimentacin, permite ajustar la cantidad de retroalimentacin.

l . Jack de auriculares Conecte los auriculares aqu. Proporciona la misma seal que la salida desde el jack OUTPUT LOW o desde el jack OUTPUT HIGH. Si desea aplicar la auto retroalimentacin, conecte este jack al jack EXT AUDIO INPUT del ARP ODYSSEY.

m . Jacks CV IN/OUT Estos jacks reciben y envan un voltaje de control (un voltaje que indica la afinacin).

n . Jacks GATE IN/OUT Estos jacks reciben y envan una seal de compuerta (una seal de que se est produciendo sonido).

o . Jacks TRIG IN/OUT Estos jacks reciben y envan un disparador (una seal de que se estn pulsado teclas del teclado). SUGERENCIA: Si utiliza el cable mini phone incluido para

conectar el jack TRIG IN y el jack GATE OUT, el ADSR EG no se volver a disparar, lo que permitir reproducir legato.

p . MODE SWITCH (solo en el ARP ODYSSEY Module) Estos conmutadores (son 5 en total) permiten ajustar el canal MIDI y la funcin de desactivacin automtica. Cuando se accionan estos conmutadores, el LED de alimentacin parpadea.

Cable phone (incluido)

Cable mini phone (incluido)

ARP ODYSSEY ARP ODYSSEY Module

- 68 -

Primeros pasos

Conexiones La siguiente ilustracin muestra un ejemplo de las conexiones tpicas. Conecte el equipo de la forma que ms le convenga.

a la toma elctrica

Adaptador de CA (incluido)

Pedalera

Monitor Amplificador de monitor, etc., etc.

Cable XLR

Cable USB

Ordenador

MIDI OUT

Auriculares

Pedal de volumen A una fuente de audio externa, etc.

Cable MIDI Cable phone mono

Cable phone mono

Cable phone mono

o

Otras conexiones de ejemplo Puede utilizar cables de patch para conectar el ARP ODYSSEY a un secuenciador como se muestra a continuacin, para que el secuenciador pueda controlar el ARP ODYSSEY para producir sonido. Si conecta el ARP ODYSSEY con el SQ1, conecte el jack PEDAL del ARP ODYSSEY al jack CV OUT del SQ1 para poder controlar la intensidad y el filtro de VCO 2 del ARP ODYSSEY.

CV OUT

GATE OUT CV IN

GATE IN

CV OUT

enchufe de conversin

Secuenciador, etc.

Debe desactivar la alimentacin de todos los dispositivos antes de realizar cualquier conexin. Si realiza conexiones con la alimentacin activada, podra daar el sistema de altavoces o bien provocar daos o un fallo de funcionamiento de los equipos.

Si desea conectar un pedal, utilice un cable mono para conectar el jack PEDAL del ARP ODYSSEY al jack OUT 1 o OUT 2 de un pedal de volumen Korg VP10 opcional (se vende por separado). En este caso, el MINIMUM VOLUME del VP 10 se debe ajustar en 0 (minimizado).

SUGERENCIA: Si desea utilizar una pedalera para activar/desactivar el portamento, conecte una pedalera Korg PS1 o PS3 opcional (se vende por separado) al jack PORTAMENTO FOOTSWITCH del ARP ODYSSEY. El portamento se desactiva al presionar la pedalera; si se libera, se aplica el efecto de portamento en el momento especificado por el deslizador PORTAMENTO.

- 69 -

M an

ua l d

e us

ua ri

o

Activar el equipo Desactive la alimentacin de sus altavoces de monitor autoalimentado o de otro

dispositivo de salida externa antes de activar la alimentacin del ARP ODYSSEY. 1. Baje el deslizador de nivel de VCA del ARP ODYSSEY (pgina 65) y el

deslizador VCA GAIN (pgina 64) a la posicin mnima.

2. Pulse el conmutador de alimentacin del ARP ODYSSEY para activar el equipo. Se iluminar el LED de alimentacin.

3. Baje los controles de volumen de los monitores autoalimentados o del sistema de salida externa, y luego actvelos.

4. Eleve los controles de volumen de los monitores autoalimentados o del sistema de salida externa hasta un nivel adecuado y ajuste el deslizador de nivel de VCA del ARP ODYSSEY.

SUGERENCIA: Si no est familiarizado con la creacin de sonidos, se recomienda realizar ahora los ajustes descritos en la seccin Ajustes bsicos (pgina 70).

Desactivar el equipo 1. Baje el volumen de los monitores autoalimentados o del sistema de salida externa,

y luego desactvelos.

2. Mantenga pulsado el conmutador de alimentacin del ARP ODYSSEY y librelo cuando el LED de alimentacin se oscurezca.

Funcin de desactivacin automtica El ARP ODYSSEY dispone de una funcin de desactivacin automtica que desactiva automticamente la alimentacin una vez transcurridas una cuatro horas desde que el instrumento se utiliz por ltima vez. Con los ajustes de fbrica, la funcin de desactivacin automtica est activada.

Cambio del ajuste de desactivacin automtica Si lo desea, puede activar o desactivar la funcin de desactivacin automtica.

No desactive la alimentacin mientras cambia este ajuste. Si lo hace podran destruirse datos, lo que provocara un fallo de funcionamiento.

SUGERENCIA: El ajuste de la funcin de desactivacin automtica se conserva aunque desactive la alimentacin.

Desactivar la funcin de desactivacin automtica

ARP ODYSSEY

1. Con las teclas C3, D3 y E3 del teclado pulsadas, pulse el conmutador de alime ntacin para activar la alimentacin.

C3 D3 E3

2. Cuando el LED de alimentacin parpadee varias veces y luego permanezca iluminado, libere el conmutador de alimentacin. Cada vez que vuelva a activar la alimentacin, el LED de alimentacin parpadear, indicando que la funcin de desactivacin automtica est desactivada.

ARP ODYSSEY Module Desactive (posicin hacia abajo) el conmutador MODE SWITCH 5 del panel posterior. La funcin de desactivacin automtica se desactivar; no hay que apagar la alimentacin y encenderla de nuevo para que el ajuste sea efectivo.

Habilitacin la funcin de desactivacin automtica

ARP ODYSSEY

1. Con las teclas C3, D3 y F3 del teclado pulsadas, pulse el conmutador de alimentacin para activar la alimentacin.

C3 D3 F3

2. Cuando el LED de alimentacin de ilumine, libere el conmutador de alimentacin. Cada vez que vuelva a activar la alimentacin, el LED de alimentacin se iluminar inmediatamente, indicando que la funcin de desactivacin automtica est activada.

ARP ODYSSEY Module Active (posicin hacia arriba) el conmutador MODE SWITCH 5 del panel posterior. La funcin de desactivacin automtica se activar; no hay que apagar la alimentacin y encenderla de nuevo para que el ajuste sea efectivo.

ON

1 2 3 4 5

ON

1 2 3 4 5

ARP ODYSSEY ARP ODYSSEY Module

- 70 -

Creacin de sonidos de ejemplo

Ajustes bsicos Ajuste los controles del ARP ODYSSEY (deslizadores, conmutadores, etc.) como se muestra en la ilustracin siguiente. Mientras toca el teclado, eleve gradualmente el deslizador de volumen VCO1 (azul) o el deslizador de volumen VCO2 (verde); escuchar el sonido de una onda de sierra. Utilice el deslizador de nivel de VCA (rojo) para ajustar el volumen.

Afinacin Una vez realizados los ajustes bsicos segn lo descrito anteriormente, utilice un afinador de venta en establecimientos comerciales para ajustar el deslizador FREQUENCY COURSE y el deslizador FREQUENCY FINE en la afinacin correcta.

- 71 -

M an

ua l d

e us

ua ri

o

Acerca de MIDI

Conexin de dispositivos MIDI Al conectar el ARP ODYSSEY a un ordenador o un secuenciador MIDI externo, puede controlar el generador de sonidos del ARP ODYSSEY desde un dispositivo externo. Utilice un cable MIDI de venta en establecimientos comerciales para conectar el conector MIDI IN del ARP ODYSSEY al conector MIDI OUT del dispositivo MIDI externo (Consulte Conexiones en la pgina 68). Conector MIDI IN: Este recibe mensajes MIDI de otros dispositivos MIDI. Conecte este conector al conector MIDI OUT del otro dispositivo.

Los mensajes de nota (se ignora la velocidad) son el nico tipo de mensajes MIDI que el ARP ODYSSEY puede recibir a travs de su conector MIDI IN. La gama de notas que se puede recibir es 012 (C0) 127 (G9).

Canal MIDI MIDI posee diecisis canales (1 16). Si conecta un dispositivo MIDI externo, debe ajustar el canal MIDI del ARP ODYSSEY para que coincida con el canal MIDI de su dispositivo MIDI externo.

Ajuste del canal MIDI del ARP ODYSSEY A continuacin se indica cmo ajustar el canal MIDI del ARP ODYSSEY. Con los ajustes de fbrica, est ajustado en el canal 1. SUGERENCIA: Para ver informacin detallada sobre cmo ajustar el canal MIDI

de su dispositivo externo, consulte el manual de funcionamiento correspondiente.

ARP ODYSSEY

1. Con las teclas C3 y C4 del teclado pulsadas, pulse el conmutador de alimentacin para activar la alimentacin. El ARP ODYSSEY est en el modo de ajuste del canal MIDI; el LED de alimentacin parpadea* para indicar el canal MIDI.

C3 C4

* El LED parpadea de forma repetida para indicar el ajuste del canal MIDI: una vez para el canal 1, dos veces para el canal 2, etc.

2. Los canales MIDI (1 16) se asignan al teclado de la siguiente forma. Pulse la tecla correspondiente al canal MIDI que desee asignar (p. ej., pulse la tecla D2 para asignar el canal 2). El LED de alimentacin contina parpadeando.*

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

3. Pulse la tecla C6 para guardar el ajuste del canal MIDI. Una vez guardado el ajuste, la alimentacin se desactiva.

C6

ARP ODYSSEY Module

Utilice los conmutadores MODE SWITCH 1 4 del panel posterior para especificar el canal MIDI. Los ajustes de canal MIDI se muestran en la tabla que viene a continuacin. El canal MIDI cambia de forma inmediata cuando se cambia el ajuste.

En caso de que cambie el canal MIDI durante el funcionamiento, las notas que estn sonando dejarn de hacerlo. La modulacin de la afinacin tambin se reiniciar.

1 ON

1 2 3 4

2 ON

1 2 3 4

3 ON

1 2 3 4

4 ON

1 2 3 4

5 ON

1 2 3 4

6 ON

1 2 3 4

7 ON

1 2 3 4

8 ON

1 2 3 4

9 ON

1 2 3 4

10 ON

1 2 3 4

11 ON

1 2 3 4

12 ON

1 2 3 4

13 ON

1 2 3 4

14 ON

1 2 3 4

15 ON

1 2 3 4

16 ON

1 2 3 4

ARP ODYSSEY ARP ODYSSEY Module

- 72 -

Conexin de un ordenador Utilice un cable USB para conectar directamente el ARP ODYSSEY a un ordenador equipado con un puerto USB para recibir mensajes MIDI del mismo modo que con los conectores MIDI. (Consulte Conexiones en la pgina 68). Los mensajes MIDI que se pueden transmitir y recibir a travs del puerto USB estn fijados en 1; los mensajes de nota (con la velocidad fijada en 64 para la transmisin, e ignorada para la recepcin) se pueden transmitir y recibir. Dado que el ARP ODYSSEY Module no tiene teclado, no puede transmitir mensajes de nota. El ARP ODYSSEY Module puede recibir mensajes MIDI de modulacin de la afinacin (pitch bend) (2 semitonos). SUGERENCIA: Los nicos mensajes MIDI que se transmiten son mensajes de nota

transmitidos cuando se toca el teclado. Los mensajes como por ejemplo PROPORTIONAL PITCH CONTROL no se transmiten.

SUGERENCIA: Para conectar a travs de USB, habr que instalar el controlador KORG USBMIDI. Descargue el controlador KORG USBMIDI del sitio Web de Korg (http://www.korg.com/), e instlelo siguiendo las instrucciones del documento incluido con el controlador.

Acerca de la tabla de implementacin MIDI La tabla de implementacin MIDI enumera los mensajes MIDI que pueden transmitirse y recibirse. Cuando utilice esta unidad con otro dispositivo MIDI, compare las respectivas tablas de implementacin MIDI para comprobar que los mensajes MIDI son compatibles. Puede descargar la tabla de implementacin MIDI de este dispositivo desde el sitio web de Korg. SUGERENCIA: Las especificaciones detalladas de MIDI se proporcionan bajo

implementacin MIDI. Para ms informacin sobre la implementacin MIDI, visite el sitio Web de Korg ( http://www.korg.com/ ).

Solucin de problemas La alimentacin no se activa Est el adaptador de CA conectado correctamente?

No hay sonido Intente ajustar los controles del panel en los ajustes descritos en la seccin Ajustes

bsicos (Consulte Ajustes bsicos en la pgina 70). Est el ARP ODYSSEY conectado correctamente al jack de entrada del

amplificador, el mezclador o los auriculares? ?Est el amplificador o el mezclador encendido, y se ha elevado el volumen de ese

dispositivo?

Es posible que el deslizador de nivel de VCA (rojo; pgina 65) o el deslizador VCA GAIN (negro; pgina 64) est ajustado en 0?

No responde a los datos MIDI enviados desde un dispositivo externo Est el cable MIDI o el cable USB conectado correctamente? (Consulte

Conexiones en la pgina 68). Coincide el canal MIDI de los datos enviados desde el dispositivo MIDI externo

con el canal MIDI global del ARP ODYSSEY? (Consulte Canal MIDI en la pgina 71).

No se puede recibir sonido desde una fuente de audio externa Est la fuente conectada correctamente al jack EXT AUDIO INPUT del panel posterior?

No se puede reiniciar la modulacin de la afinacin (pitch bend) del ARP ODYSSEY Module . La modulacin de la afinacin se puede reiniciar recibiendo un mensaje MIDI

como "Reset All Controllers" (reiniciar todos los controladores). Si desea reiniciarla utilizando esta unidad, puede desactivar la alimentacin y volver a activarla, o puede accionar uno de los conmutadores MODE SWITCH para cambiar temporalmente el canal MIDI.

Especificaciones Sistema de generacin de sonido: 0 +40 C (eXpanded Modeling Technology) Teclado (solo en el ARP ODYSSEY): 37 notas (teclado delgado, sin sensibilidad a la

velocidad, sin aftertouch) Polifona mxima: 2 voces para duofnica; normalmente monofnica CONTROLADORES

Posiciones de transposicin: 2 octavas abajo, normal, 2 octavas arriba Control de afinacin proporcional: Pad (afinacin hacia abajo): aproximadamente 2

/ 3 octavas Pad (modulacin) Pad (afinacin hacia arriba): aproximadamente

+2 / 3 octavas Generador de ruido: Tipos de espectros de ruido (blanco y rosa) Portamento: Velocidad mxima: aproximadamente 0,01 ms/oct.

Velocidad mnima: aproximadamente 1,5 s/oct. VCO (oscilador controlado por voltaje)

Formas de onda: Sierra, cuadrada, impulso (impulso dinmico) Gama de frecuencias: VCO1 en modo de frecuencia baja,

0,2 Hz 20 Hz: VCO1 y VCO2 (gama de audio)

- 73 -

M an

ua l d

e us

ua ri

o

de aproximadamente 20 Hz 20 kHz Desviacin de calentamiento: 1/30 de semitono desde activacin mx. Amplitud del impulso: 50 % 5 % Modulacin de amplitud del impulso: ADSR, +45%; LFO, +15% Respuesta controlada por voltaje: 1 V/oct. Cambios de frecuencia mxima: Onda sinusoidal de LFO, +1/2 oct.; onda

cuadrada de LFO, +1,5 oct.; ADSR, +9 oct.; S/H, +2 oct.

VCO1 es la prioridad de nota baja, VCO2 es la prioridad de nota alta VCF (filtro controlado por voltaje)

Tipos: Paso bajo (I: 12 dB/oct., II III: 24 dB/oct.) Gama de frecuencias: 16 Hz 16 kHz Q til mxima: 30 Resonancia: 1/2 oscilacin automtica Respuesta controlada por voltaje: Tecla C3 (borde izquierdo): 0 V, tecla C6 (borde

derecho) 3 V VCA (amplificador controlado por voltaje)

Gama dinmica: 80 dB MODULADOR EN ANILLO

Tipo: Digital Seal de entrada: VCO1, VCO2 (onda cuadrada)

MUESTREO Y RETENCIN Fuentes de comando: Teclado o disparador del LFO Seales muestreadas: VCO1: onda de sierra y onda cuadrada, VCO2:

onda cuadrada y ruido rosa GENERADOR DE ENVOLVENTE DE ADSR

Tiempo de ataque: 5 ms 5 s Tiempo de cada: 10 ms 8 s Nivel sustain: 0 100% o pico Tiempo de liberacin: 15 ms 10 s

GENERADOR DE ENVOLVENTE DE AR Tiempo de ataque: 5 ms 5 s Tiempo de liberacin: 10 ms 8 s

JACKS DE ENTRADA DE CONTROL Pedal: Jackphonemono6,3mm Conmutador de pedal de portamento: Jackphonemono6,3mm

JACKS DE SALIDA DE AUDIO BAJO

Conector: Jackphonemono6,3mm Nivelmximodesalida: -20dBuconcargade10k Impedanciadesalida: 10k ALTO Conector: Conector XLR Nivelmximodesalida: +4dBuconcargade1k Impedanciadesalida: 330

JACK HEADPHONES Conector: Jackphoneestreo6,3mm Nivelmximodesalida: 50mW+50mWconcargade33 Impedanciadesalida: 10 * Controlable mediante mando de volumen.

JACK DE ENTRADA DE AUDIO EXTERNA (EXT AUDIO INPUT) Conector: Jackphonemono6,3mm Nivel mximo de entrada: 10 dBu Impedanciadeentrada: 22k

Conector MIDI: IN Conector USB: Tipo B JACKS CV IN/OUT

CV del teclado (IN/OUT): 1 V/oct. Conector: Jackphonemono3,5mm

JACKS GATE IN/OUT GATE IN: +3 V (mnimo) GATE OUT: +10 V, tecla abajo; 0 V todas las teclas arriba Conector: Jackphonemono3,5mm

JACKS TRIG IN/OUT TRIGGER IN: +3 V de impulso mn., 10 s de duracin mnima TRIGGER OUT: +10 V de impulso al pulsar la tecla, 10 s de duracin Conector: Jackphonemono3,5mm

Fuente de alimentacin: Jack de adaptador de CA (DC 9V ) Consumo: 6,5 W Dimensiones (anchura x profundidad x altura), Peso:

ARP ODYSSEY 502 x 380 x 120 mm, 5 kg ARP ODYSSEY Module 496 x 265 x 89 mm, 3,7 kg

Elementos incluidos: Adaptador de CA, cable phone, cable mini phone, manual del usuario

Opciones: Pedal de volumen VP10, pedalera PS1/PS3

* Las especificaciones y el aspecto estn sujetas a cambios sin previo aviso por mejora.

ARP ODYSSEY ARP ODYSSEY Module

- 74 -

ARP ODYSSEY/ARP ODYSSEY Module

2

ACAC 100V AC

AC

AC AC

ACAC

AC

AC

AC AC

- 75 -

ODYSSEY ODYSSEY19721981ARP 3 Model 2800Rev. 119721974 19741975 Model 2810 2813Rev. 219751976 CV/GATE PPC Model 2820 2823Rev. 319781981 Model 2800 2813 RCA/PHONEXLR/PHONE

ARP ODYSSEYVCOVCFVCA

377[ARP ODYSSEY Module]

ADSRAR2 PPCPROPORTIONAL PITCH CONTROL 2 LFOS&H 3ARP ODYSSEY

PCMIDIUSBMIDI

ARP ODYSSEYARP ODYSSEY Module ARP ODYSSEY

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 ODYSSEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 . . . . . . . . . . . . . . 77

VCO- 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

VCO- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

LFOSAMPLE AND HOLD . . . . . . . . . . . . . . . 80

AUDIO MIXERVCFHPFVCA . . . . . . . . . . . . . 81

ENVELOPE GENERATOR . . . . . . . . . . . . . . . . 83

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

MIDI . . . . . . . . . . . . . . . . . . . . . . . . 89

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

ARP ODYSSEY ARP ODYSSEY Module

- 76 -

NOISE GENERATOR

AUDIO MIXER

VOLTAGE CONTROLLED

FILTER

HIGH PASS

FILTER

VOLTAGE CONTROLLED

AMPLIFIER

RING MOD

SAMPLE AND

HOLD

SAMPLE AND HOLD

MIXER

VOLTAGE CONTROLLED OSCILLATORS

LOW FREQUENCY OSCILLATOR

PEDAL ADSR AND AR

ENVELOPE GENERATORS

TRIGGER

ARP ODYSSEY Module: Only MIDI IN

KEYBOARD

MIDI IN

ARP ODYSSEY: Built-in Keyboard and MIDI IN

- 77 -

a

b c

d

e f g

a. NOISE GENERATOR ..............................................[WHITE, PINK]

b. PORTAMENTO .......................................[MINMAX] MIN

MAX PORTAMENTO FOOTSWITCH

c. MODE ........................................................................... [ON, OFF] TRANSPOSE

d. TRANSPOSE ......................... [2 OCTAVES UP, 0, 2 OCTAVES DOWN] 2

e. PROPORTIONAL PITCH CONTROL -

f. PROPORTIONAL PITCH CONTROL -

g. PROPORTIONAL PITCH CONTROL -

ARP ODYSSEY ARP ODYSSEY Module

- 78 -

VCO- 1

c

d e f

h i j

g

a b

1VCO- 1

a. FREQUENCY COARSE .............. [20(0 .2)Hz2K(20)Hz] 20Hz 2KHz 0. 2Hz 20Hz

20Hz 2KHz

b. FREQUENCY FINE ...................................... [400cent]

c. ....................................[AUDIO KYBD ON, LF KYBD OFF] AUDIO KYBD ONVCO- 1CVLF KYBD OFFCVLFOVCO- 2

d. FM

e. FM FM

f. PULSE WIDTH WIDTH ............................ [50%MIN]

g. PULSE WIDTH MOD

h. FM ................................................. [LFO , LFO ] LFO

i. FM ..........................................................[S/H, ADSR ] ADSR

j. ...... [LFO , ADSR ]

- 79 -

VCO- 2

c

d e f

h i j

g

a b

2VCO- 2

a. FREQUENCY COARSE ........... [20(0 .2)Hz2K(20)Hz] 20Hz 2KHz SYNC

20Hz 2KHz

b. FREQUENCY FINE ................................... [400cent] SYNC

c. SYNC............................................................................ [OFF, ON] SYNC VCO- 2VCO- 1

d. FM

e. FM FM

f. PULSE WIDTH WIDTH ............................ [50%MIN]

g. PULSE WIDTH MOD

h. FM ................................. [LFO , S/H MIXER OR PEDAL] LFOS/H MIXER S/H MIXER OR PEDAL

i. FM ..........................................................[S/H, ADSR ] ADSR

j. ...... [LFO , ADSR ]

ARP ODYSSEY ARP ODYSSEY Module

- 80 -

LFOSAMPLE AND HOLD

a

b c d

e f g

a. LFO FREQLFO ........................ [0 .2Hz20Hz] LFO

b. S/H VCO- 1S/H MIXER

c. S/H VCO- 2S/H MIXER

d. S/H OUTPUT LAG S/H MAX

e. S/H .......................[VCO-1 , VCO-1 ] S/H MIXERVCO- 1

f. S/H .......................... [NOISE GEN , VCO-2 ] S/H MIXERVCO- 2

g. S/H ................................... [LFO TRIG , KYBD TRIG] S/H MIXERLFO

- 81 -

AUDIO MIXERVCFHPFVCA

d e

f

c

a

g h i j

k l m

n

b

o p q r s t

a. VCF FREQ ..........................................[16Hz16KHz] LPF 16Hz

b. VCF RESONANCE .......................... [MINSELF OSC] VCF

c. VCF TYPE ...................................................................... [ , , ] VCF ODYSSEY Rev. 1 ODYSSEY Rev. 2 ODYSSEY Rev. 3

d. HPF CUTOFF FREQ ...........................[16Hz16KHz] HPF

e. DRIVE ........................................................................... [OFF, ON] ONVCA

f. VCA GAIN VCA

g. NOISE/RING MOD

h. VCO- 1 VCO- 1

i. VCO- 2 VCO- 2

j. VCF FREQS/H MIXER

ARP ODYSSEY ARP ODYSSEY Module

- 82 -

k. S/HLFO

l. ARADSR

m. VCA VCAADSRAR DRIVEONVCA

n. NOISE/RING MOD .........[NOISE, RING MOD]

o. VCO- 1 ....... [VCO-1 , VCO-1 ] VCO- 1 78

p. VCO- 2 ...... [VCO-2 , VCO-2 ] VCO- 2 79

q. KYBD CV/S/H MIXER OR PEDAL ...................................................... [KYBD CV, S/H MIXER OR PEDAL] KYBD CVVCO S/H MIXER OR PEDALS/H MIXER PEDAL VCF

r. S/H/LFO .......[S/H, LFO ] LFO

s. ADSR/AR ............................... ............................................................................. [ADSR , AR ]

t. VCA EG .................................................... [AR , ADSR ] VCA

- 83 -

ENVELOPE GENERATOR

c

a

b

d e f

h i j

g

a. AR EG - ATTACK AR

b. AR EG - RELEASE AR

c. LED

d. ADSR EG - ATTACK ADSR EG

e. ADSR EG - DECAY ADSR EG

f. ADSR EG - SUSTAIN ADSR EG

g. ADSR EG - RELEASE ADSR EG

h. ADSR ................[KYBD GATE, LFO REPEAT ] ADSR KYBD GATEEGFO REPEATLFOEGLFO FREQEG

i. ADSR ............................... [KYBD REPEAT, AUTO REPEAT] ADSRAR LFO REPEAT KYBD REPEATEGLFO AUTO REPEAT/

j. AR .....................[KYBD GATE, LFO REPEAT ] AR ADSR

ARP ODYSSEY ARP ODYSSEY Module

- 84 -

e f g h i j k l

m n o

b c da

onm

p

k le f g h i jb c da

ARP ODYSSEY Module

ARP ODYSSEY

a. ACAC

b. DC 9V AC AC

c.

d. MIDI IN MIDIMIDI

e. USB B MIDI

f. PEDAL SQ-1()

g. PORTAMENTO FOOTSWITCH

h. OUTPUT LOW

i. OUTPUT HIGH XLR

j. EXT AUDIO INPUT EXT AUDIO INPUTAUDIO MIXERVCFVCA

Tip: EXT AUDIO INPUT

k.

l. OUTPUT LOWOUTPUT HIGH EXT AUDIO INPUT

m. CV IN/OUT Control Voltage=

n. GATE IN/OUT Gate=

o. TRIG IN/OUT Trigger=

Tip: TRIG INGATE OUT ADSR EG

p. MODE SWITCH APP ADESSEY Module MIDI LED

- 85 -

AC

XLR

USB

MIDI OUT

MIDI

SQ- 1PEDALSQ- 1CV OUT VCO 2

CV OUT

GATE OUT CV IN

GATE IN

CV OUT

PEDAL VP- 10 OUT 1 OUT 2 VP- 10MINIMUM VOLUME

Tip: PS- 1PS- 3PORTAMENTO FOOTSWITCH PORTAMENTO

ARP ODYSSEY ARP ODYSSEY Module

- 86 -

1. VCA82 VCA GAIN81

2. LED

3.

4. VCA

Tip: 87

1.

2. LED

4

Tip:

ARPODYSSEY

1. C 3D 3E 3

C3 D3 E3

2. LED LED

ARPODYSSEYModule

MODE SWITCH5

ARPODYSSEY

1. C 3D 3F 3

C3 D3 F3

2. LEDLED

ARPODYSSEYModule

MODE SWITCH5

ON

1 2 3 4 5

ON

1 2 3 4 5

- 87 -

VCO- 1VCO- 2 VCA

FREQUENCY COARSE FREQUENCY FINE

ARP ODYSSEY ARP ODYSSEY Module

- 88 -

MIDI

MIDI MIDI MIDIMIDI INMIDIMIDI OUT 85 MIDI IN: MIDIMIDIMIDI OUT

MIDI INMIDI 012C 0 127G 9

MIDI MIDI1 16 MIDIMIDIMIDIMIDI

MIDI MIDI1

Tip: MIDIMIDI

ARPODYSSEY

1. C 3C 4MIDI LEDMIDI*

C3 C4

* MIDI1122

2. MIDI1 16 MIDI 2D 2LED *

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

3. C 6MIDI

C6

ARPODYSSEYModule

MODE SWITCH14MIDI MIDI

MIDI

1 ON

1 2 3 4

2 ON

1 2 3 4

3 ON

1 2 3 4

4 ON

1 2 3 4

5 ON

1 2 3 4

6 ON

1 2 3 4

7 ON

1 2 3 4

8 ON

1 2 3 4

9 ON

1 2 3 4

10 ON

1 2 3 4

11 ON

1 2 3 4

12 ON

1 2 3 4

13 ON

1 2 3 4

14 ON

1 2 3 4

15 ON

1 2 3 4

16 ON

1 2 3 4

- 89 -

USBUSB85 USBMIDI 64 ARP ODYSSEY Module ARP ODYSSEY ModuleMIDI2

Tip: MIDI PROPORTIONAL PITCH CONTROL

Tip: USBKORG USB-MIDI http://www.korg.com/ KORG USB-MIDI

MIDI MIDIMIDI MIDIMIDI MIDIMIDI

Tip: MIDIMIDIMIDI http://www.korg.com/

AC

87 VCA: 82 VCA GAIN 81

MIDI MIDIUSB85 MIDIMIDIMIDI

88 MIDI

EXT AUDIO INPUT

ARPODYSSEYModule Reset All ControllersMIDI

MODE SWITCH MIDI

0 + 40

ARP ODYSSEY 37

2

22 2/ 3 + 2/ 3

0. 01msec./oct 1. 5sec./oct

VCO 0. 2Hz 20HzVCO- 1

20Hz 20kHzVCO- 1VCO- 2 1/ 30 50% 5% + 45%ADSR+ 15%LFO 1V/oct + 1/ 2LFO+ 1. 5LFO

+ 9ADSR+ 2S/H VCO- 1VCO- 2

ARP ODYSSEY ARP ODYSSEY Module

- 90 -

VCF 12dB/oct24dB/oct 16Hz 16kHz Q 30 1/ 2 C 3key0C 6key 3

VCA 80dB

VCO- 1VCO- 2

& LFO VCO- 1VCO- 2

ADSR 5msec. 5sec. 10msec. 8sec. 0 100% 15msec. 10sec.

AR 5msec. 5sec. 10msec. 8sec.

6. 3mm 6. 3mm

LOW 6. 3mm 20dBu@ 10k 10k HIGH XLR + 4dBu@ 1k 330

6. 3mm 50mW+ 50mW@ 33 10

EXT AUDIO INPUT 6. 3mm 10dBu 22k

MIDI IN

USB B

CV IN/OUT CVIN/OUT 1V/oct 3. 5mm

GATE IN/OUT GATE IN + 3V GATE OUT + 10V0V 3. 5mm

TRIG IN/OUT TRIG IN + 3V10sec.

TRIG OUT + 10V10sec.

3. 5mm

ACDC 9V

6. 5W

ARP ODYSSEY 502 380 120mm5 kg ARP ODYSSEY Module 496 265 89mm3. 7kg

AC

VP- 10PS- 1/PS- 3

- 91 -

1. 1 2.

3

3. This warranty is valid only in Japan.

4.

5.

6.

1.

2.

ARP ODYSSEY / ARP ODYSSEY Module

WARNING! This Product is only suitable for sale in Japan. Properly qualified service is not available for this product if purchased elsewhere. Any unauthorised modification or removal of original serial number will disqualify this product from warranty protection.

: 10:0017:00 PHS

: 168-0073 1-18-16 2F TEL 03(5355)3537 / FAX 03(5355)4470

: KORG Import Division 206-0812 4015-2 www.korg.com/jp/kid/

Module

M odule

IMPORTANT NOTICE TO CONSUMERS

This product has been manufactured according to strict specications and voltage requirements

that are applicable in the country in which it is intended that this product should be used. If you

have purchased this produc

Manualsnet FAQs

If you want to find out how the ARP ODYSSEY Module KORG works, you can view and download the KORG ARP ODYSSEY Module Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for KORG ARP ODYSSEY Module as well as other KORG manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a KORG ARP ODYSSEY Module. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the KORG ARP ODYSSEY Module Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This KORG ARP ODYSSEY Module Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download KORG ARP ODYSSEY Module Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print KORG ARP ODYSSEY Module Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the KORG ARP ODYSSEY Module Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.