Contents

KORG MOSS-TRI User's Guide PDF

1 of 67
1 of 67

Summary of Content for KORG MOSS-TRI User's Guide PDF

1E

Contents

1. Introduction --------------------- 1 Features of MOSS-TRI ----------------- 1

2. Bank M Program Structure -- 2 Program structure ------------------------ 2

Editing -------------------------------------- 3

Characteristics of each oscillator ---- 4

3. Parameters ---------------------- 5 Program Play Mode --------------------- 5

Program Play P1 ---------------------- 5 11: Program Play ------------------ 5

Program Edit Mode --------------------- 6

Program Edit P1 ---------------------- 6 11: Prog Basic ---------------------- 6 12: OSC Basic -------------------- 10 13: OSC 1 Pitch ------------------ 12 14: OSC 2 Pitch ------------------ 13 15: Sub Pitch --------------------- 13

Program Edit P2 -------------------- 14 21: OSC ---------------------------- 14

01: Standard ----------------------------------- 14 02: Comb Filter ------------------------------- 17 03: VPM ---------------------------------------- 19 04: Resonance --------------------------------- 21 05: Ring Modulation ------------------------ 23 06: Cross Modulation ----------------------- 24 07: Sync Modulation ------------------------ 25 08: Organ Model ----------------------------- 26 09: Electric Piano Model ------------------- 28 10: Brass Model ------------------------------- 30 11: Reed Model ------------------------------- 33 12: Plucked String Model ------------------ 36 13: Bowed String Model ------------------- 40

22: OSC 2 -------------------------- 42 23: Sub/Noise ------------------- 43

Program Edit P3 -------------------- 45 31: Mixer -------------------------- 45 32: Filter 1 ------------------------- 47 33: Filter 1 SUB ------------------ 50 34: Filter 2 ------------------------- 52 35: Filter 2SUB ------------------- 52

Program Edit P4 -------------------- 53 41: Amp --------------------------- 53 4-2: Amp EG ----------------------- 55

Program Edit P5 -------------------- 57 51: EG 1 ---------------------------- 57 52: EG 2 ---------------------------- 59 53: EG 3 ---------------------------- 59 54: EG 4 ---------------------------- 59

Program Edit P6 -------------------- 60 61: LFO 1 -------------------------- 60 62: LFO 2 -------------------------- 62 63: LFO 3 -------------------------- 62 64: LFO 4 -------------------------- 62

Program Edit P7 -------------------- 63 Program Edit P8 -------------------- 63

4. Data----------------------------- 64 Retrigger Controller List ------------ 64

Modulation Source List -------------- 64

Precautions ------------------------------ 65

Additional message ------------------- 65

Contents

1. Introduction Thank you for purchasing the MOSS-TRI DSP Synthesizer Option. To ensure long and trouble-free enjoyment, please read this users guide carefully and use the product correctly.

Before you use this product, be sure to read the Safety precautions found at the beginning of the Parameter Guide.

This guide explains the bank M parameters which are added when the MOSS-TRI DSP Synthesizer Option is installed (pre-installed in the Trinity V3 series). For details on parameters other than bank M, refer to your Parameter Guide, Basic Guide, and Effect Guide.

When this option is installed (pre-installed in the Trinity V3 series), the bank S programs created by the Solo-TRI option will become invalid. However, explanations of bank S in the Parameter Guide, Basic Guide, and Effect Guide will still apply to bank M. Also, please refer to the Voice Name List for V3 together with the Voice Name List which you already have.

In combination mode, bank M programs can be selected only for one timbre (page 4 in Parameter Guide). In Sequencer mode, bank M programs can be selected only for one track ( page 72 in Parameter Guide).

If a bank M program is selected for any timbre in a combination, the D-mod Src Tempo for the AMS or effect of the timbre program will use the Prog. Tempo setting (page 61 of this manual) (when the MIDI Clock Source is Internal).

In all modes, you must use an insertion effect when using bank M programs. If you do not use an insertion effect, the output will be low.

Features of MOSS-TRI This is a MOSS (Multi-Oscillator Synthesis System) tone generator with six voices of polyphony. Bank M contains 64 sounds which use the MOSS tone generator. When the PBS-TRI Flash ROM Option is installed, an additional 64 sounds are added to bank M, bringing the total to 128 sounds. The MOSS tone generator parameters are divided into voice, EG, LFO, effect and control sections. The voice section contains an oscillator section and a filter section, etc.

The oscillator section contains two oscillators (1, 2) which allow you to use 13 oscillator algorithms (standard, ring modulation, VPM, resonance, organ model, electric piano model etc.), in addition to a sub oscillator and a noise generator.

The filter section provides two filters, each of which allows you to use one of five types of filtering, including a dual-band pass filter with two independent center frequencies that let you simulate human voice sounds or the body resonances of a violin or guitar.

This voice section can be modulated by five EG units and four LFO units to apply diverse changes in pitch, timbre and volume to the sound.

INTRODUCTION

Introduction

2. Bank M program structure

Program structure Each program of bank M has the following structure.

Oscillator section This is the section which creates the waveform that is the basis of the sound. These settings are made by the Program Edit P1 and Program Edit P2 parameters.

OSC 1, 2 Thirteen methods of sound production (i.e., thirteen oscillator types) are provided. Two of these oscillator types can be used together, and settings made to specify the basic pitch, etc. However depending on the oscillator type, only one oscillator may be available. These settings are made by the 1-2: OSC Basic, 1-3: OSC 1 Pitch, 1-4: OSC 2 Pitch, and 2-1: OSC parameters.

Sub oscillator This lets you use one of four types of basic waveform. Pitch-related settings can be made in the same way as OSC 1 and 2. These settings are made by the 1-5: Sub Pitch and 2-2: Sub/Noise parameters.

Noise generator This generates white noise. The noise can be sent through a multi-mode filter (low pass filter, high pass filter, band pass filter). These settings are made by the 2-2: Sub/Noise parameters.

Mixer section The output of oscillators 1 and 2, the sub oscillator, and the noise generator are mixed with the feedback from the amp section, and output to multi-mode filters 1 and 2 (the filter section). These settings are made by the 3-1: Mixer parameters.

Mixer

Oscillator 1

Oscillator 2

Sub Oscillator

Noise Generator

Feedback

Amp1

Amp2

Pan LPF/HPF/BPF/BRF/2BPF

LPF/HPF/BPF/BRF/2BPF

Filter 1

Filter 2

Insert Effect

Master Effect

EQ 1/L/Mono 2/R

OSC Section Mixer Section

Filter Section AMP Section FX Section

EG1 EG2 EG3 EG4 Amp.EG

LFO1 LFO2 LFO3 LFO4

Joy Stick, Ribbon Controller & other controllers

3 4

Bank M Program Structure

Filter section This section modifies the waveform by attenuating or emphasizing specific portions of the frequency spectrum. It contains two multi-mode filters. Each filter can be set to one of the following types: low pass filter, high pass filter, band pass filter, band reject filter, or dual band pass filter. This lets you modify the brightness of the sound. You can also select the way in which the two filters will be connected with the mixer section and amp section. These settings are made by the 3-2: Filter 1, 3-3: Filter 1 SUB, 3-4: Filter 2, and 3-5: Filter 2 SUB parameters.

Amp section This section modifies the volume of the output from the filter section. It contains two independent amplifiers. The signal which is input to each amplifier will depend on how the two filters are connected. The amp section also contains an amplitude envelope generator (Amp EG) which controls the amp. These settings are made by the 4-1: Amp and 4-2: Amp EG parameters.

Effect section This section applies effects to the signal which is output from the amp section. It has the same parameter structure as the programs of other banks. These settings are made by the Program Edit P7 and Program Edit P8 parameters.

EG section This section provides four general-purpose envelope generator (EG) units. The four EGs for which settings are made in the EG section can be used as modulation sources for the parameters of each section, in order to apply time-variant change to the sound. These settings are made by the Program Edit P5 parameters.

LFO section This section provides four general-purpose LFO units. The four LFOs for which settings are made in the LFO section can be used as modulation sources for the parameters of each section, in order to apply cyclic change to the sound. These settings are made by the Program Edit P6 parameters.

Program basic section Settings are made here for the program name, category, scale, key assign, keyboard, and the control nctions (joystick, ribbon controller, etc.). These settings are made by the 1-1: Prog Basic parameters.

Editing Bank M programs are similar to bank A and bank B programs, in the respect that they can be edited in Program Play mode or by using the Performance Editor. One method to try is to use an existing program which resembles the desired sound, and use Program Edit mode to edit the parametes. The filter, amp, effect, EG and LFO sections will function in the same way as for banks they do inand B, but the display page structure and the parameters are different ( 3. Parameters in this manual). The operation and parameters of the oscillator and mixer sections are unique to bank M programs.

Bank M Program Structure

Program Structure

Characteristics of each oscillator For bank M sounds, OSC 1 provides thirteen oscillator types (methods of sound generation) and OSC 2 provides nine types. In Program Edit P1 1-2: OSC Basic you can select one of these types for each oscillator, to specify the combination. If OSC 1 is set to an oscillator type of 01:Standard to 09:Electric Piano Model, you will also be able to select an oscillator type of 01:Standard to 09:Electric Piano Model for OSC 2. If OSC 1 is set to an oscillator type of 10:Brass Model to 13: Bowed String Model, OSC 2 will not be available for use.

01: Standard OSC This simulates the oscillator of an analog synthesizer. It can produce the same effects as an analog synthesizer, such as pulse width modulation ( page 14 of this manual).

02: Comb Filter OSC This oscillator creates pitched sound from noise or an impulse. It can create a wide variety of sounds not only noisy sounds, but also sounds ranging from synth-bass to strings (page 7 of this manual).

03: VPM OSC (Variable Phase Modulation OSC) This oscillator uses phase modulation to create overtones. By modulating the phase of two oscillators and using a wave shaping table to process the sound, rich overtones can be produced (page 19 of this manual)

04: Resonance OSC This oscillator uses four tunable filters which are set up in series. Noise is input through the filter bank for very ethereal sounds (page 21 of this manual).

05: Ring Modulation OSC - This oscillator multiplies the modulator and carrier and outputs the resultant signal.

06: Cross Modulation OSC - This oscillator uses a modulator to frequency-modulate a carrier. 07: Sync Modulation OSC (oscillator sync)

These are special oscillators which simulate the effect of two oscillators which are used to modulate each other, which was a technique that was possible on analog synthesizers. These are especially suitable for producing sounds that are rich in overtones, such as bells, metallic sounds or gongs (page 23, 24, 25 of this manual).

08: Organ Model This simulates a drawbar organ with three drawbars (when one oscillator is used) or six drawbars (when two oscillators are used) (page 26 of this manual). Since each drawbar can use one of four types of waveform, a wide range of tones can be produced.

09: Electric Piano Model This is a physical model which simulates a warm, vintage electric piano sound (page 8 of this manual).

10: Brass Model This is a physical model which simulates a brass instrument such as a trumpet or trombone (page 30 of this manual).

11: Reed Model This is a physical model which simulates a wind instrument such as a saxophone or flute (page 33 of this manual)

12: Plucked String Model This is a physical model which simulates a plucked string instrument such as a guitar or bass guitar (page 36 of this manual).

13: Bowed String Model This is a physical model which simulates a bowed string instrument (page 40 of this manual).

Bank M Program Structure

3. Parameters This section explains the bank M parameters which are added when the MOSS-TRI DSP Synthesizer Option is installed (pre-installed in the Trinity V3 series). For details on parameters other than bank M, refer to your Parameter Guide, Basic Guide, and Effect Guide.

Program Play Mode

Program Play P1

11: Program Play Here, you can select programs and perform simple editing. For details on the parameters, refer to page 1 of your Parameter Guide: 1. Program Play mode.

Depending on the oscillator type(s) used by the program or the combination of effect types, a brief interval of time may be required before a newly-selected program actually begins operating after it is selected.

1-1: Prog Play

Param eters

Prog. Play P1

Program Edit Mode The Write Program item in the page menu commands of each page lets you write an edited program to the program number you specify. Be sure to write an edited program that you wish to keep. If you turn off the power or select another program before you write, the edited program cannot be recovered. For details refer to Basic Guide page 23, 9. Writing a program or combination.

Program Edit P1 Here you can make basic settings for the program, and basic settings for the oscillator(s) that will be used.

11: Prog Basic

11a: Program Name This indicates the program that was selected in Program Play mode. You can press the text edit button to access a window that allows you to rename the program (page 6 in Basic Guide).

When you wish to write a renamed program, be sure to use the Write Program operation (page 23 in Basic Guide). If you select another program or turn off the power, the newly specified program name will be lost.

11b: Category Two categories can be specified for each program. When selecting programs in Program Play mode, Combination Play mode, or Sequencer mode, you can use these categories to search for the desired program.

A (Category A) [KeyboardDrums/Perc.] With the factory settings, these are listings of different types of instruments, but they can be changed in Global mode 4-1: Category Program A (page 128 in Parameter Guide).

B (Category B) [User Category P01P16] The factory set category names can be changed in Global mode 4-2: Category Program B (page 128 in Parameter Guide).

11a 11b

11c

11d

11e

11f

1-1: Prog Basic

11c: Assign/Hold Here, you can specify how notes will sound when keys are pressed.

Voice Assign [Mono (Multi), Mono (Single), Poly] Selects whether the sound will be played monophonically or polyphonically. Mono (Multi): Multi-triggered monophonic playing. Mono (Single): Single-triggered monophonic playing Poly: Polyphonic playing

When Poly is selected, the Retrigger Control and Threshold parameters will be unavailable.

Priority [Last, Low, High] Specifies the priority order that will be used when the number of keys pressed exceeds the maximum polyphony. Last: The last-pressed note will take priority Low: The lowest note will take priority High: The highest note will take priority

Hold When this is checked, the note will continue to sound after the key is released. However, if the EG selected by 4-1: Amp (normally the Amp EG is used) has a sustain level of zero, the note will decay naturally.

Retrigger Control [OFFMIDI (CC#83)] Retrigger refers to the action of resetting the EG and LFO at the time of note-on (the EG will return to its start level, and the LFO will return to the beginning of the cycle of its waveform). Here you can select the controller (Retrigger Controller page 64 of this manual) which will specify whether or not the sound will be retriggered when a note-on occurs.

Threshold (Retrigger Control Threshold) [1127] Specifies the value at which EG and LFO will be retriggered by a note-on. The state of the controller selected by Retrigger Control (i.e., whether the controller value is above or below the specified Threshold value) will determine whether or not the sound will be retriggered when a note-on occurs. The operation of this function will differ depending on the Voice Assign setting. With a setting of Mono (Multi), retriggering will occur if the controller is below the threshold value. If Retrigger Control is OFF, retriggering will always occur. With a setting of Mono (Single), retriggering will occur if the controller is above the threshold value. If Retrigger Control is OFF, retriggering will not occur.

If a note-on occurs when all notes are off, retriggering will always occur. LFOs whose Key Sync is turned OFF will not be reset even if retriggering occurs.

11d: Unison Here, you can make settings for unison mode.

Unison [OFF, 2voices, 3voices, 6voices] Specifies the number of notes which will be sounded in unison. With a setting of OFF, unison will not be used. The maximum polyphony will be three notes with a setting of 2voices, two notes for a setting of 3voices, and one note for a setting of 6voices.

Mode [Fixed, Dynamic] Specifies how the number of voices specified by the Unison setting will be allocated. With a setting of Fixed, the number of voices specified by the Unison setting will always sound. With a setting of Dynamic, the number of voices will be determined by the current note-playing situation.

Detune [099] Detunes the notes that are sounded simultaneously by the Unison function.

1-1: Prog Basic

Param eters

Prog. Edit P1

11e: Scale Specifies the scale type

Type (Scale Type) [Equal TemperamentAll Range User Scale] Selects the basic scale for the internal tone generator. The user scales can be specified in Global mode 3-1: User Scale (page 127 in Parameter Guide).

Equal Temperament The most widely used scale, consisting of equally-spaced semitone steps.

Pure Major The major chords of the selected key will be perfectly in tune.

Pure Minor The minor chords of the selected key will be perfectly in tune.

Arabic This reproduces a quarter-tone scale of Arabic music.

Pythagorean A scale based on ancient Greek musical theory, suitable for playing melodies.

Werckmeister (Werkmeister III) An equal-tempered scale used in the later Baroque period.

Kirnberger (Kirnberger III) A scale created in the 18th century, and used mainly for tuning harpsichords.

Slendro An Indonesian gamelan scale in which the octave consists of 5 notes. If the Key parameter is set to C, use the C, D, F, G, and A keys. (Other keys will produce the same pitches as equal temperament.)

Pelog An Indonesian gamelan scale in which the octave consists of 7 notes. If the Key parameter is set to C, use only the white keys. (The black keys will produce the same pitches as equal temperament.)

Octave User Scale This is the one-octave scale that you create in Global mode 3-1b: Octave Notes (page 127 in Parameter Guide).

Stretch This is a tuning used on acoustic pianos.

All Range User Scale This is the full-range scale (C-1=G9) that you create in Global mode 3-1a: All Notes (page 127 in Parameter Guide).

Key (Scale Key) [CB] Specifies the tonic note of the selected scale.

Random [099] As this value is increased, the pitch of the note will become increasingly unpredictable. Normally you will leave this set at zero. Adjust this parameter when you wish to simulate instruments whose pitch is naturally unstable, such as tape- mechanism organs or acoustic instruments.

1-1: Prog Basic

11f: Panel Switch Assign These parameters assign the function of the front panel SW1 and SW2 switches (assignable panel switches 1 and 2).

SW1 [JS(X) LockModulation (CC#80)]

SW2 [JS(X) LockModulation (CC#81)]

The functions which can be assigned to SW1 and SW2 are the same (except for Modulation), and are as follows: JS(X) Lock, JS(+Y) Lock, JS(Y) Lock, Ribbon(X) Lock, Ribbon(Z) Lock, After Touch Lock, JS & Ribbon Lock

Each time you press SW1 (or SW2), the selected controller will alternate between Lock/Unlock (a lit LED indicates Lock). When you press SW1 (or SW2) while operating a controller, subsequent movement of that controller will produce no change. For example if you select JS(+Y) Lock, and then move the joystick away from yourself and press SW1 (or SW2), the joystick (+Y) movement will be locked (held) at that position, and modulation will continue to be applied even after the joystick is allowed to return. By then moving the joystick in the (Y) direction, you can apply both types of modulation simultaneously.

If this is locked, the corresponding controller will also stop transmitting MIDI, but reception will still occur.

Octave Down Each time you press SW1 (or SW2), the original octave setting will alternate with a setting of one octave lower.

Octave Up Each time you press SW1 (or SW2), the original octave setting will alternate with a setting of one octave higher.

Portamento Off Each time you press SW1 (or SW2), the portamento effect will alternate between On and Off (lit LED indicates Off). This is valid only for bank M programs.

CC#65 will be transmitted each time On/Off occurs (a value of 0 for Off, 127 for On).

Modulation Select this when you wish to use the switch as a AMS or Effect Dynamic Modulation source. In this case, you must first specify the control destination.

SW1 and SW2 differ for this function alone. For each On/Off, SW1 will transmit CC#80 , and SW2 will transmit CC#81 (a value of 0 for Off, 127 for On).

AMSource

AMSource

MIDI

MIDI

MIDI

Param eters

Prog. Edit P1

1-1: Prog Basic

12: OSC Basic

12a: Multi Oscillator Synthesis Setup Here, you can make settings for the oscillator. The parameters that are set in 2-1: OSC 1 and 2-2: OSC 2 will differ depending on the oscillator type that is selected here.

OSC 1 (Oscillator 1 Type) [01: Standard13: Bowed String Model] Selects the oscillator type for oscillator 1. 01: Standard 02: Comb Filter 03: VPM (Variable Phase Modulation OSC) 04: Resonance 05: Ring Modulation 06: Cross Modulation 07: Sync Modulation 08: Organ Model 09: Electric Piano Model 10: Brass Model 11: Reed Model 12: Plucked String Model

13: Bowed String Model

When 10: Brass Model, 11: Reed Model, 12: Plucked String Model, or 13: Bowed String Model are selected, OSC 2 cannot be used.

OSC 2 (Oscillator 2 Type) [01: Standard09: Electric Piano Model] Selects the oscillator type for oscillator 2. Refer to OSC 1.

12b: Common Pitch Modulation Creates time-varying changes in the pitch of all oscillators (oscillators 1 and 2, and the sub oscillator).

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects the modulation source (page 64 of this manual) that will control the pitch of all oscillators (oscillators 1 and 2, and the sub oscillator).

Intensity (Common Pitch AMS Intensity) [99+99] Specifies the depth and direction of the effect produced by AMS.

12a

12b

12c

12d

1-2: OSC Basic

12c: Bending Specifies the width of pitch change that will occur when the joystick is moved to left and right.

JS(+X) (Joystick Intensity +X) [60+24] Specifies the amount and direction of pitch change (in semitone units) that will occur when the joystick is moved to the right. With positive (+) settings the pitch will rise, and with negative (-) settings the pitch will fall. A setting of 12 will produce one octave of change.

Step (Joystick Step +X) [Continuous, 1/8, 1/4, 1/2, 112] Specifies how the pitch will change when the joystick is moved to the right. Continuous: Smooth change.

1/8: Change in 1/8 semitone steps. 1/4: Change in 1/4 semitone steps. 1/2: Change in 1/2 semitone steps. 1...12: Change in steps of the specified number of semitones (up to 1 octave).

JS(X) (Joystick Intensity X) [60+24] Specifies the amount and direction of pitch change (in semitone units) that will occur when the joystick is moved to the left.

Step (Joystick Step X) [Continuous, 1/8, 1/4, 1/2, 112] Specifies how the pitch will change when the joystick is moved to the left. Refer to Step (Joystick Step +X).

If the Step (Joystick Step +X) or Step (Joystick Step X) settings are greater than the settings for JS (+X) and JS (X), the pitch will not change.

12d: Portamento These settings specify how portamento will be applied. (Portamento creates a smooth change in pitch from one note to the next.) The setting you make here is valid only if Enable is checked.

Enable Check this when you wish to use portamento.

Fingered Check this when you want to apply portamento only when a note is pressed while continuing to hold the previous note.

Time [099] Specifies the portamento time. Higher values will cause the pitch to change more slowly.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Time.

Intensity (Portamento Time AMS Intensity) [99+99] Specifies the way in which the portamento time will be controlled by the AMS .

1-2: OSC Basic

Param eters

Prog. Edit P1

13: OSC 1 Pitch Here, you can make settings for the basic pitch of oscillator 1, pitch modulation, and pitch slope.

13a: Basic Pitch Specifies the basic pitch of oscillator 1

Octave [32'4'] Specifies the basic pitch of oscillator 1 in steps of an octave. 32' is two octaves below, 16' is one octave below, 8' is standard pitch, and 4' is one octave above.

Transpose [12+12] Adjusts the basic pitch specified by Octave in semitone steps.

Tune [50+50] Makes fine adjustments to the pitch in one-cent steps.

Frequency Ofs [10.0+10.0] Makes fine adjustments to the pitch in 0.1 Hz steps.

13b: Pitch Modulation Specifies the pitch Modulation.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) which will modify the pitch (e.g., apply vibrato).

Intensity (Pitch AMS.1 Intensity) [99+99] Specifies the depth and direction of the pitch change that will be controlled by AMS.1.

AMS.1 Int (AMS.1 Intensity Alternate Modulation Source) [OFFMIDI (CC#83)] Specifies the controller (page 64 of this manual) that will control the Intensity (Pitch AMS.1 Intensity).

Intensity (AMS.1 Int AMS Intensity) [99+99] Specifies the depth of the pitch modulation effect controlled by AMS.1 Int .

13a

13b

13c

1-3: OSC 1 Pitch

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) which will modify the pitch (e.g., apply vibrato).

Intensity (Pitch AMS.2 Intensity) [99+99] Specifies the depth and direction of the pitch change that will be controlled by AMS.2.

13c: Pitch Slope Specifies how pitch will change in relation to the keyboard (key)

Center Key [C1G9] Specifies the key at which Lower/Higher keyboard tracking will begin to apply.

Low Slope [1.00+2.00] Specify the depth and direction of the pitch change that will occur for notes below the Center Key.

High Slope [1.00+2.00] Specifies the depth and direction of the pitch change that will occur for notes above the Center Key. When Low Slope and High Slope are set to +2.0, playing one octave upward from the Center Key will cause the pitch to rise two octaves. With a setting of 1.0, playing one octave upward will cause the pitch to fall one octave. With a setting of 0.0, the notes in the respective areas will produce the same pitch as the Center Key. To play pitches normally, set this parameter to +1.0.

14: OSC 2 Pitch Here, you can make settings for the oscillator type, basic pitch, pitch keyboard tracking, and pitch modulation of oscillator 2. The parameters of oscillator 2 are the same as for oscillator 1. (Refer to the explanation of the 13: OSC 1 Pitch page).

15: Sub Pitch Here, you can make settings for the oscillator type, basic pitch, pitch keyboard tracking, and pitch modulation of sub oscillator . The parameters of sub oscillator are the same as for oscillator 1. (Refer to the explanation of the 13: OSC 1 Pitch page).

1-3: Osc1 Pitch, 1-4: OSC2 Pitch, 1-5: Sub Pitch

Param eters

Prog. Edit P1

C-1 C4 C9 C-1

C9

Pitch

Key

Center Key

Int=-1.0 Int=+2.0 Int=+1.0

Int=0.0

Program Edit P2 Here, you can make settings for each oscillator type. The oscillator type is specified in 1-2a: Multi Oscillator Synthesis Setup of 1-2: OSC Basic. The display pages that appear will depend on the selected oscillator type.

21: OSC 01: Standard

This oscillator produces the waveforms used by an analog synthesizer (sawtooth wave, pulse wave, triangle wave) and sine wave. Sawtooth wave, pulse wave and triangle wave waveforms can be modified using waveform modulation. You can specify either sawtooth wave or pulse wave as the main waveform, and mix triangle wave or sine wave with this for output. The level of these three waveforms can be adjusted independently. In addition, wave shaping can be applied to the output of this oscillator.

Waveform modulation Pulse width modulation (PWM) on an analog synthesizer produces time-varying change in the pulse width of a pulse wave. The waveform modulation provided by the MOSS-TRI option is an extension of this, which varies not only the pulse width but also the waveform of a sawtooth wave or triangle wave. Waveform modulation will affect the various waveforms as follows. Sawtooth wave Waveform modulation will modify a sawtooth waveform as shown below, creating time-variant change in the sound.When modulation is 0, the basic sawtooth waveform will be produced, and when it is 99, a sawtooth wave of double the frequency will be produced. If the modulation value is a negative number, a different effect will result than with positive settings. Pulse wave Waveform (pulse width) modulation will modify a pulse waveform as shown below, creating time-variant change in the sound. When modulation is 0, a square wave will be produced, and when it is 99, the pulse width will be 0, meaning that there will be no sound. If the modulation value is a negative number, the results will be inverted. Triangle wave Waveform modulation will modify a ramp wave as shown below, creating time-variant change in the sound. When modulation is 0, a triangle wave will result, and as the modulation value increases, the waveform will become a ramp wave (a waveform in which the slope is broken in two). At a modulation value of 50, a trapezoidal wave will result, and at a value of 99 the waveform will once again be a triangle wave. If the modulation value is a negative number, the results will be inverted.Compared to sawtooth or pulse waves, this waveform produces a strong fundamental with fewer overtones, making it particularly suitable for bass sounds etc.

-99 -33 0 33 66 99

-98 -33 0 33 66 98

-99 -25 0 25 50 75 99

21a

21b

21c

2:1 OSC 1 (01: Standard)

21a: Wave Main Wave [Saw, Pulse]

Selects the main waveform. Select either Saw (sawtooth wave) or Pulse (pulse wave).

Level [099] Specifies the output level of the main waveform.

Wave Edge [099] Adjusts the amount of high-range overtones for the main waveform. As the pitch rises, this effect will become stronger, and in the low range there will be little effect. Lower settings of this parameter will produce a more mellow sound, and in the vicinity of 0 the volume will also decrease.

Triangle Level [099] Specifies the output level of the triangle waveform. It will be output mixed with the main waveform.

Sine Level [099] Specifies the output level of the sine waveform. It will be output mixed with the main waveform.

Phase Shift (Triangle & Sine Phase Shift) [99+99] Specifies the phase difference between the main waveform and the triangle and sine waveforms. (The triangle and sine waveforms will always be in phase with each other.)

21b: Waveform(Waveform Modulation) Waveform [99+99]

Specifies the waveform. For the way in which this value will affect the waveform, refer to the diagrams shown on the previous page for sawtooth wave, pulse wave, and triangle wave.

LFO [LFO1LFO4] Selects the source LFO for waveform modulation. LFO settings are made in the Program Edit P6.

Intensity (Waveform Modulation LFO Intensity) [99+99] Specifies the depth and direction of the waveform modulation that will be controlled by the LFO specified in LFO.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Waveform.

Intensity (Waveform AMS Intensity) [99+99] Specifies the depth and direction of the waveform modulation controlled by the AMS. For negative settings, the polarity of the modulation source will be inverted.

21c: Wave Shape Input (Input Level) [099]

Specifies the level of the signal that is input from the standard oscillator to the wave shaping table.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Input.

Intensity (Input Level AMS Intensity) [99+99] Specifies the depth and direction of the waveform modulation controlled by the AMS.

Output level

Input level

Input waveform

Output waveform

Example of when Input Level is modified (Table Type : Reso)

Input Level =99

Input Level =75

Input Level =50

Input Level =25

2:1 OSC 1 (01: Standard)

Param eters

Prog. Edit P2

2:1 OSC 1 (01: Standard)

Type (Wave Shape Table Type) [Clip/Reso] Use the radio buttons to select the wave shaping table which will modify the input waveform. Clip (clip type) and Reso (resonant type) tables will modify the waveform as shown by the diagrams in Shape, below.

Offset (Wave Shape Offset) [99+99] Specifies an offset amount that will be added to the signal specified by Input.

Shape [099] Specifies the characteristics of the table which will modify the input waveform. The characteristics of the table will change as follows.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Shape.

Intensity (Shape AMS Intensity) [99+99] Specifies the depth and direction of the waveform modulation controlled by the AMS.

Balance [099] Specifies the balance between the signal that has passed through the wave shaping table and the output signal from the standard oscillator. With a setting of 99, it will be only the output of the wave shaping table.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Balance.

Intensity (Balance AMS Intensity) [99+99] Specifies the depth and direction of the waveform modulation controlled by the AMS.

Output level

Input level

Input waveform (Input Level fixed)

Output waveform

Example of when Offset is modified (Table Type: Clip)

Offset=50 Offset=0 Offset=-50

Output level

Input level

Shape of the wave shaping table and the Shape parameter CLIP type

Output of the clip type table when a sawtooth waveform is input

Waveform level

Waveform before being input to the table

Shape:0 Shape:99

Output level

Input level

Resonant type

Output of the resonance type table when a sawtooth wave is inputWaveform

level

Waveform before being input to the table

Shape:0 Shape:99

2:1 OSC 1 (02: Comb Filter)

Param eters

Prog. Edit P2

02: Comb Filter In this oscillator, the signal from the other oscillator waveform or the noise generator is sent through a comb filter, and the feedback level of the comb filter is varied in order to produce tonal change. When noise is input, raising the feedback of the comb filter will gradually change the sound into a pitched tone.

21a: Input

Input [OSC2(1)+Noise, SubOSC+Noise, Filter1+Noise, Filter2+Noise, Pulse Noise, Impulse]

Selects the signal that will be input to the comb filter.

Frequency

Example of when noise is input

Level

As the Feedback value increases, the sound will become more pitched.

Delay

Comb Filter Feedback

Comb Filter

High Damp

Noise Level

Input Wave Level

Noise

Pulse Noise or Impulse

Comb Oscillator

Comb Filter

Feedback=0

Feedback>0

Input Level Mod.Source/Intensity

OSC1/2 or Sub OSC Filter1 out Filter2 out

Level

Level

Frequency

Frequency

21a

21c

21d

21b

Example of when an Impulse is input

As the Feedback is increased, the decay time will become longer.

Time

Time

Comb Filter

Pluse Width=0

Pluse Width=99

Feedback=0

Feedback>0

Time

Time

2:1 OSC 1 (02: Comb Filter)

Level (Input Wave Level) [099] Specifies the volume level of the signal that will be input to the comb filter.

Noise Level [099] This parameter will be available only if Input has been set to OSC2(1)+Noise, SubOSC+Noise, Filter1+Noise or Filter2+Noise. It specifies the volume level of the noise generator output which will be input to the comb filter.

Pulse Width [099] This parameter will be available only if Input has been set to Pulse Noise or Impluse. It specifies the length of time that the Pulse Noise or Impluse will last after being triggered.

21b: Level Modulation

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control the volume level of the signal being input to the comb filter. The volume level is set by the Level or the Noise Level.

Intensity (Input Wave Level AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

21c: Feedback

Feedback [099] Specifies the amount of feedback for the comb filter. If this value is high, the resonance of the comb filter will be high, and the tone will have a clear sense of pitch. Conversely, if this value is low, the input signal will be output without change, and if the input signal is only noise, the output signal will have no sense of pitch.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control Feedback.

Intensity (Feedback AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1 .

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control Feedback.

Intensity (Feedback AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.2 .

21d: High Damp

High Damp [099] Specifies the amount of attenuation that will be applied to the high-frequency component of the feedback signal within the comb filter. As this value is increased, the tone will become more mellow. Conversely, decreasing this value will produce a brighter tone.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control High Damp.

Intensity (High Damp AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

2:1 OSC 1 (03: VPM)

Param eters

Prog. Edit P2

03: VPM The output of a carrier is phase-modulated by a modulator, and output through wave shape processing. By controlling the wave shaping parameters and the feedback gain, tonal changes that are different than simple phase modulation can be produced.

21a: Carrier

Wave [Saw, Square, Triangle, Sine] Selects the carrier waveform.

Level [099] Specifies the output level of the carrier. This will determine the output level of the VPM oscillator.

AMS.1 (Alternate Modulation 1 Source) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control Level.

Intensity (Level AMS.1Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1.

AMS.2 (Alternate Modulation 2 Source) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control Level.

Intensity (Level AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.2.

21b: Wave Shape

Shape [099] Specifies the number of cycle of wave shaping. As this value is increased, the number of cycles will increase, causing more overtones to be added to the high-frequency range of the sound.

2-1a

21b

21c 21d

21e

Modulator Pitch Carrier Pitch (Basic Pitch)

Carrier Level

Output

Wave Shape Parameter

Feedback Gain

Modulator Level

Modulator Carrier Wave Shape

Table valiation

Shape:0 Shape:99

Table Variation

2:1 OSC 1 (02: Comb Filter)

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control Shape value.

Intensity (Shape AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control Shape value.

Intensity (Shape AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.2.

Type (Wave Shap Type) [1, 2] 1: The signal after wave shaping will be output without further change. If Shape is set to the minimum value, the phase modulated signal will be output essentially without change. 2: A rounded waveform will be obtained regardless of the Shape value.

21c: Feedback [099] Specifies the amount of the output after wave shaping that will be fed back to the carrier.

21d: Modulator Wave [Saw, Square, Triangle, Sine, OSC2(1), SubOSC, Filter1, Filter2]

Selects the modulator waveform.You may select the other oscillator or the sub oscillator, etc. If you select OSC 2(1), SubOSC, Filter 1, or Filter 2, it will not be possible to set 2-1e: Frequency.

Level [099] Specifies the output level of the modulator. This value will determine the amount of modulation that is applied to the 2-1a: Carrier setting.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control Level.

Intensity (Level AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control Level.

Intensity (Level AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.2.

21e: Frequency Coarse [0.5, 116]

Specifies a multiplication factor which will be applied to the pitch of the modulator, relative to the 2-1a: Carrier setting.

Fine [50+50] Makes fine adjustments to the pitch of the modulator.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control the pitch of the modulator.

Intensity (Frequncy AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control the pitch of the modulator.

Intensity (Frequncy AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.2.

2:1 OSC 1 (04: Resonance)

Param eters

Prog. Edit P2

04: Resonance This oscillator produces a wide range of tonal change by allowing you to specify the cutoff frequency and resonance of four band pass filters (BPF). You can select one of the following sources to be the input for the filters: the output of the other oscillator, the sub-oscillator, the output of the noise generator, or the output of filter 1 or filter 2.

21a: Input

Input [OSC2(1), SubOSC, Noise, Filter1, Filter2] Selects the signal that will be input to the four band bass filters.

If you select 04:Resonance for OSC 1 and 2 in 1-2a: Multi Oscillator Synthesis Setup, and select the other oscillator as the input for each, the result will be unstable the sound may be non-reproduceable, or you may hear no sound at all.

Level [099] Specifies the level of the signal that is input to the four band pass filters.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control Level.

Intensity (Level AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control Level.

Intensity (Level AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.2.

21a

21b

21c

OSC 1/2

Sub OSC

Noise Generator

BPF2 BPF3

BPF4

BPF1

Resonance1 Coarse1

Level1Input Level

Input Select

Filter1 out

Filter2 out

21b: BPF14 Here, you can make settings for each band pass filter 14.

Level [099] Specifies the output level.

Coarse [116] Specifies the harmonic (overtone) of the oscillator pitch at which the center frequency of the filter will be located. You can specify from the first to the 16th harmonic.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Coarse.

Int. (BPF Frequency AMS Intensity) [15+15] Specifies the depth and direction of the effect of AMS. Positive (+) settings will allow the Coarse value to be increased, and negative () settings will allow the Coarse value to be decreased. At this time, the center frequency of band pass filter 1 will change in steps of harmonics, creating the impression that the pitch is changing step- wise.

Fine [99+99] Makes fine adjustments to the center frequency of band pass filter 1 specified by the Coarse parameter.

Reso [099] Specifies the resonance. Increasing this value will produce a stronger effect.

21c: Resonance

Resonance AMS (Resonance Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control the resonance that was specified for each band pass filter.

Intensity (Resonance AMS Intensity) [99+99] Specifies the depth and direction of the effect of Resonance AMS.

2:1 OSC 1 (04: Resonance)

05: Ring Modulation This multiplies the modulator and carrier and outputs the signal produced. One of four types of waveform can be selected as the carrier. Since the result will be a metallic sound with little sense of pitch, this is suitable for producing sound effects. The Ring Modulation oscillator contains an internal carrier oscillator. The output of the other oscillator etc. can be selected as the modulator.

21a: Input Input [OSC2(1), SubOSC, Noise, Filter1, Filter2]

Specifies the modulator.

If you select 05:Resonance for OSC 1 and 2 in 1-2a: Multi Oscillator Synthesis Setup, and select the other oscillator as the Input for each, you may hear no sound at all for some parameter settings.

Carrier [Saw, Square, Triangle, Sine] Specifies the carrier waveform.

Wave Edge [099] Specifies the amount of high frequency harmonics for the carrier waveform. As this value is decreased, the sound will have less high-frequency harmonics, and as it approaches 0 the volume will also decrease.

Type [1, 2] Selects the modulation type. The two types differ in the tone of the high range. Type 2 will produce a brighter sound than type 1.

21b: Mod. Depth Mod. Depth [099]

Specifies the depth of modulation. At a setting of 0, the carrier waveform will be output without change.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control Mod. Depth.

Intensity (Modulation Depth AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control Mod. Depth.

Intensity (Modulation Depth AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.2.

2:1 OSC 1 (05: Ring Modulation)

Param eters

Prog. Edit P2

Ring Modulation

Modulator

Carrier Wave

21a

21b

2:1 OSC 1 (06: Cross Modulation)

06: Cross Modulation This uses a modulator to frequency-modulate a carrier. You can select one of four waveforms as the carrier. In general, a pitch envelope is applied to the modulator. A carrier oscillator is built-in to the Cross Modulation OSC. You can select the output of the other oscillator etc. as the modulator.

21a: Input

Input [OSC2(1), SubOSC, Noise, Filter1, Filter2] Specifies the modulator.

Carrier [Saw, Square, Triangle, Sine] Specifies the carrier waveform.

Wave Edge [099] Specifies the amount of high frequency harmonics for the carrier waveform. As this value is decreased, the sound will have less high-frequency harmonics, and as it approaches 0 the volume will also decrease.

21b: Mod. Depth

Mod. Depth [099] Specifies the depth of modulation. At a setting of 0, the carrier waveform will be output without change.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control Mod. Depth.

Intensity (Modulation Depth AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control Mod. Depth.

Intensity (Modulation Depth AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.2.

Cross Modulation Cross Modulation Depth

Modulator

Carrier Wave

21a

21b

2:1 OSC 1 (07: Sync Modulation)

Param eters

Prog. Edit P2

07: Sync Modulation This uses the modulator as the master waveform and the carrier as the slave waveform (which will be synchronized to the master). When the master waveform begins a new cycle (i.e., the instant that it passes the zero point going from negative to positive), the phase of the slave waveform is reset to 0, causing it to begin a new cycle.

21a: Input

Input [OSC2(1), SubOSC, Noise, Filter1, Filter2] Specifies the master waveform (modulator).

Slave [Saw, Square, Triangle, Sine] Specifies the slave waveform.

Wave Edge [099] Specifies the amount of high frequency harmonics for the slave waveform. As this value is decreased, the sound will have less high-frequency harmonics, and as it approaches 0 the volume will also decrease.

Modulator Wave (Master)

Carrier Wave (Slave)

Sync Modulation

21a

2:1 OSC 1 (08: Organ Model)

08: Organ Model This is an oscillator used to produce organ-type sounds. The oscillator simulates three drawbars similar to electric organs of the past. You can specify the footage [Harmo] and waveform setting for each drawbar, allowing a wide range of sounds to be created.

21a: Drawbar 1 Wave [Sine 1, Sine 2, Sine 3, Triangle]

Specifies the waveform for drawbar 1. Sine 1 contains only the fundamental (i.e., a pure sine wave). Sine 2 and Sine 3 are waveforms which contain the first two and the first three harmonics respectively.

Coarse (Harmonics Coarse) [116] Specifies the pitch of drawbar 1, relative to one octave below the oscillator pitch.

Fine (Harmonics Coarse Fine) [99+99] Makes fine adjustments to the pitch of drawbar 1.

Level [099] Specifies the volume level of drawbar 1.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control the Level of drawbar 1.

Intensity (Level AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1.

Wave

Sine1 or Sine2 /Sine3/Triangle

Harmonics (Pitch)

LevelDrawbar1

Drawbar2

Drawbar3

Percussion Level

Precussion

Precussion Decay/Level Mod.

21a

21c

21d

21e

21b

2:1 OSC 1 (08: Organ Model)

Param eters

Prog. Edit P2

21b: Percussion Level [099] Specifies the volume level of the percussion effect for drawbar 1.

21c: Drawbar 2 The parameters are structured identically to those of 2-1a: Drawbar 1. Refer to 2-1a: Drawbar 1 and 2-1b: Percussion Level.

21d: Drawbar 3 The parameters are structured identically to those of 2-1a: Drawbar 1. Refer to 2-1a: Drawbar 1 and 2-1b: Percussion Level.

21e: Percussion Generator

Trigger [Single/Multi] Use the radio buttons to specify how the percussion effect will be triggered. With a setting of Single, the percussion effect will apply to the first-played note from a condition of no sound. With a setting of Multi, the percussion effect will apply to each note that is played.

Decay [099] Specifies the decay length of the percussion. As this value is increased the decay time will become longer.

Level AMS (Level Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control the percussion level of each drawbar.

Intensity (Level AMS Intensity) [99+99] Specifies the depth and direction of the effect of Level AMS on the percussion level.

2:1 OSC 1 (09: Electric Piano Model)

09: Electric Piano Model This oscillator simulates an electric piano. There are four groups of parameters: Hammer (which specifies how the shape and motion of the hammer will affect tonal change and attack noise), Tone Generator (which vibrates in response to being struck by the hammer), Pickup (which specifies the tonal change that occurs when the vibration of the tone generator is converted into an electrical signal), and Low EQ (which is a shelving-type low EQ to adjust the low range).

21a: Hammer

Force [099] Specifies the Strength with which the hammer strikes the tone generator. Higher settings will produce a brighter sound.

Force Velocity Curve [OFF, 099] Specifies how changes in velocity will affect Force. As this value is increased, velocity will have a greater effect on Force, allowing more dynamic tonal change to be produced. With a setting of OFF, the Force will be constant.

Width (Hammer Width) [099] Simulates the shape of the hammer. As this value is increased, the width of the hammer will become narrower, and the sound of the tone generator and hammer noise will become sharper.

Click Noise Level [099] Specifies the volume of the hammer noise that occurs at the attack.

Pickup

Tone Generator

Hammer

Pickup Position

to Low EQ

21a

21b

21c

21d

21e

2:1 OSC 1 (09: Electric Piano Model)

Param eters

Prog. Edit P2

21b: Tone Generator The Decay and Release that you specify here will control the output level of the oscillator. In order for these settings to have an effect, they must be set longer than the decay and release of the EG which you are using for the Amp.

Decay [099] Specifies the decay time of the tone generato.

Release [099] Specifies the release time of the tone generator.

21c: Overtone

Level [099] Specifies the volume of the higher overtones that are produced when the tone generator vibrates.

Frequency [099] Specifies the frequency of the overtones.

Decay [099] Specifies the decay time of the overtone volume.

21d: Pickup Position

Position [099] Specifies the location of the pickup in relation to the tone generator. With low settings, the pickup will be placed in the center of the vertical vibration of the tone generator, causing the second partial to be emphasized and the fundamental to be less audible.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Position.

Intensity (Pickup Position AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

21e: Low EQ Makes settings for a Low EQ (shelving type) that will adjust the output signal.

Frequency (EQ Frequency) [049] Specifies the cutoff frequency of the Low EQ (shelving type) that will be applied to the output signal.

Gain [18+18] Specifies the gain of the Low EQ.

2:1 OSC 1 (10: Brass Model)

10: Brass Model This oscillator is a physical model which simulates lip-reed instruments such as a trumpet or trombone. By using key velocity or modulation wheel to modulate the Pressure (the force of breath blown into the mouthpiece) you can produce performance expressions that are very similar to those of an actual lip-reed instrument. The parameters are as follows: Inst Type determines the model which simulates the bore length and shape of the instrument, Breath Pressure indicates the force of breath that is blown into the mouthpiece, Lip Character produces the tonal changes that result from lip position or tension, Bell Character produces the tonal changes that result from the shape of the end of the bore, and Peaking EQ performs a final tonal adjustment.

This oscillator allows you to choose from two types of pitch bending: jump bending using a mode jump as on a trumpet (by varying the bore length), and smooth bending produced by sliding the length of the bore as on a trombone.

For some parameter settings, the pitch may not change according to the notes that are played on the keyboard. In some cases, high-pitched notes may have a lower volume, or may not sound at all.

Lip (Character) Specify tonal change produced by lip position

Inst Type Select a model which simulates the bore length and shape of various instruments

Bell Specify the shape of the end of the bore

Specify the force of breath that is blown into the mouthpiece Specify the amount of breath noise

Pressure Noise {

Brass Model

Signal Flow

Brass Model Peaking EQ Strength

21a 21b

21c 21d

21e

2:1 OSC 1 (10: Brass Model)

Param eters

Prog. Edit P2

21a: Inst Type Inst Type [Brass 1, Brass 2, Brass 3, Horn 1, Horn 2, Reed Brass]

Selects the instrument type which will determine the bore length and shape of the simulated instrument.

Jump Bend (+X) Specifies how the pitch will change when the joystick is moved in the +X direction (toward the right). If this is checked, the pitch will rise by in steps by changing the resonance of the bore, as on a trumpet. If this is unchecked, the pitch will rise smoothly, as on most synthesizers.

Jump Bend (X) Specifies how the pitch will change when the joystick is moved in the X direction (toward the left).

If Jump Bend (+X) and Jump Bend (X) are checked, notes may not sound depending on the position of the joystick and the pitch range setting. For details on setting the pitch range of the joystick, refer to 1-2c: Bending.

21b: Breath Pressure EG [EG 1EG 4, Amp EG]

Selects the EG which will control pressure. For details on the settings for each EG, refer to Program Edit P5 for EG 14, and 4-2: Amp EG for Amp EG.

Intensity (Pressure EG Intensity) [99+99] Specifies the depth and direction of the effect that the EG will have on the pressure.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control pressure. If you select After Touch, pressing down on the keyboard will produce the effect of the instrument being blown strongly. If you select Joy Stick(X), rotating the Joy Stick in the + direction will produce this effect. In this case, setting Intensity (Pressure EG Intensity) to 0 will allow you to completely control the breath pressure by operating the specified controller.

Intensity (Pressure AMS.1 Intensity) [99+99] Specifies the depth and direction of the change in pressure controlled by AMS.1.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control pressure.

Intensity (Pressure AMS.2 Intensity) [99+99] Specifies the depth and direction of the change in pressure controlled by AMS.2.

Breath Noise [099] Specifies the volume level of the breath noise. Since this uses the signal from the noise generator, the filter of the noise generator can be used to modify the tone of the noise.

Strength [099] Adjusts the tone. Higher settings of this value will produce a overdriven sound.

21c: Lip Character Lip [099]

Specifies the tonal change that is produced by lip position and tension. Higher settings of this value will produce a harder (more firmly blown) sound. Lower settings will produce a softer tone.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Lip.

Intensity (Lip Character AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

2:1 OSC 1 (10: Brass Model)

21d: Bell Character

Tone [099] Specifies the tone of the bell. As this value is increased, the low frequency portion will disappear, producing a less solid tone.

Resonance [099] Specifies the level at which the frequency region in the area of the Tone will be boosted. As this value is increased, the resonance effect will become stronger.

21e: Peaking EQ

Frequency [049] Specifies the center frequency of the frequency range that will be boosted or attenuated by the Peaking EQ. Increasing this value will raise the center frequency.

Q [029] Specifies the width of the Peaking EQ frequency band. Increasing this value will narrow the frequency band that is boosted or attenuated.

Gain [18+18] Specifies the amount by which the area specified by Frequency and Q will be boosted or attenuated.

2:1 OSC 1 (11: Reed Model)

Param eters

Prog. Edit P2

11: Reed Model This oscillator is a physical model which simulates woodwind reed instruments such as a saxophone or oboe. By using key velocity or the modulation wheel to control Pressure (the strength with which the reed is blown), you can use performance expressions that are very close to those of an actual woodwind instrument. Also, by modulating the characteristics of the reed, you can produce tonal changes that correspond with the way in which a reed is blown.21a: Inst Type

Inst Type [Hard Sax 1...Reed Synth] Selects the type of instrument whose bore shape and reed characteristics will be simulated. Hard Sax 1, Hard Sax 2, Hard Sax 3, Soft Sax 1, Soft Sax 2, Double Reed 1, Double Reed 2, Bassoon, Clarinet, Flute 1, Flute

2, Pan Flute, Ocarina, Shakuhachi, Harmonica 1, Harmonica 2, Reed Synth

Jump Bend (+X) Specifies how the pitch will change when the joystick is moved in the +X direction (toward the right). If this is checked, the pitch will rise in steps by changing the resonance of the bore, as on a flute. If this is unchecked, the pitch will rise smoothly, as on most synthesizers.

Jump Bend (X) Specifies how the pitch will change when the joystick is moved in the X direction (toward the left).

If Jump Bend (+X)and Jump Bend (X) are checked, notes may not sound depending on the position of the joystick and the pitch range setting. For details on setting the pitch range of the joystick, refer to 1-2c: Bending.

Inst Type Select a model to specify the bore length and shape of the instrument to be simulated

Reed Character Specify the vibrational characteristics of the reed

Presure Specify the force of the breath that is blown into the reed Noise Specify the amount of breath noise

{

Reed Model Bell Character Wave Shape

Reed Model

Signal Flow

Peaking EQ

21a 21b

21c 21d 21e

21f

2:1 OSC 1 (11: Reed Model)

21b: Breath Pressure EG [EG 1EG 4, Amp EG]

Selects the EG which will control pressure. For details on the settings for each EG, refer to Program Edit P5 for EG 14, and 4-2: Amp EG for Amp EG.

Intensity (Pressure EG Intensity) [99+99] Specifies the depth and direction of the effect that the EG will have on the pressure.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control pressure. If you select After Touch, pressing down on the keyboard will produce the effect of the instrument being blown strongly. If you select Joy Stick (X), moving the joy stick toward the right will produce this effect.

Intensity (Pressure AMS.1 Intensity) [99+99] Specifies the depth and direction of the change in pressure controlled by AMS.1.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control pressure.

Intensity (Pressure AMS.2 Intensity) [99+99] Specifies the depth and direction of the change in pressure controlled by AMS.2.

Breath Noise [099] Specifies the volume level of the breath noise. Since this uses the signal from the noise generator, the filter of the noise generator can be used to modify the tone of the noise.

21c: Reed Character AMS (Alternate Modulation Source) [OFFMIDI (CC#83)]

Selects a modulation source (page 64 of this manual) that will modulate the characteristics of the reed.

Intensity (Reed AMS Intensity) [99+99] Specifies the depth of the modulation effect that AMS will have on the reed.

21d: Bell Character Tone [099]

Specifies the tone of the bell. As this value is increased, the low frequency portion will disappear, producing a less solid tone.

Resonance [099] Specifies the level at which the frequency region in the area of the Tone will be boosted. As this value is increased, the resonance effect will become stronger.

21e: Wave Shape

Type (Wave Shape Table Type) [Clip/Reso] Use the radio buttons to select the wave shaping table which will modify the input waveform. For the way in which the table will modify the waveform, refer to the Wave Shape diagram shown in 01: Standard (page 16 of this manual).

Offset [99+99] Specifies the offset value that will be added to the Reed OSC signal that is input to wave shaping.

2:1 OSC 1 (11: Reed Model)

Param eters

Prog. Edit P2

Shape [099] Specifies the character of the table that will shape the input waveform. For details on how the waveform will change, refer to the Wave Shape diagram (page 16 of this manual) for the 01: Standard OSC.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Wave Shape.

Intensity (Shape AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

21f: Peaking EQ

Frequency [049] Specifies the center frequency of the range that will be boosted or attenuated by the Peaking EQ. Increasing this value will raise the center frequency.

Q [029] Specifies the width of the Peaking EQ frequency band. Increasing this value will narrow the frequency band that is boosted or attenuated.

Gain [18+18] Specifies the amount by which the range specified by Frequency and Q will be boosted or attenuated.

12: Plucked String Model This oscillator is a physical model which simulates plucked string instruments such as a guitar or bass guitar. You can specify aspects of the model such as the attack waveform that is produced when the string is plucked by a pick or finger, the characteristics of the string, the location of the pickup, etc

.

21a: Attack Attack Level [099]

Specifies the force with which the string is plucked.

Velocity [99+99] Specifies the depth and direction of the effect that velocity will have on Attack Level. The effect will be as shown in the following diagram.

2:1 OSC 1 (12: Plucked String Model)

Attack Level Specify the strength of playing (the level of the attack waveform). Noise Specify the level and tone of the noise included in the attack waveform. Attack Curve Specify the envelope of the attack waveform.

Parameters relating to the attack waveform

Delay/Release Specify the ratio of the wave transmitted along the string which is reflected back from the bridge (decay/release time).

Bridge Bridge

String Position Specify the location at which the string is struck.

Parameters relating to the characteristics of the string Damping Specify the high frequency attenuation of the wave transmitted along the string. To simulate muted playing techniques, control this parameter. Dispersion Specify tonal change caused by inharmonicity of the higher partials

Harmonics Position Specify the string location to be pressed to play harmonics Harmonics Mod.Source / Mod.Int. Specify the controller which will control the harmonics effect, and the depth of control.

String Model

String Model Pickup Low EQ & Low Boost

Signal Flow

21a 21b 21c

21d

21e 21f

Parameter value

Velocity value1 127

Int= + Int=

Int=+99 Int=99

Int= 0

Noise Level [099] Specifies the level of the noise component that is included in the attack waveform. As this value is increased, a greater portion of noise will be included in the attack, and the sound will be brighter with more overtones. The noise signal used here is taken from the output of the noise generator.

Velocity (Noise Level Velocity Control) [99+99] Specifies the depth and direction of the effect that velocity will have on Noise Level. For the way in which the effect occurs, refer to Velocity (page 36 of this manual).

21b: Attack Curve Curve Up [099]

Specifies the steepness of the rising edge of the attack waveform.When the rising or falling edge is steep, the tone will be harder.

Velocity (Curve Up Velocity Control) [99+99] Specifies the depth and direction of the effect that velocity will have on Curve Up. For the way in which the effect occurs, refer to Velocity (page 36 of this manual).

Curve Down [099] Specifies the steepness of the falling edge of the attack waveform.

Velocity (Curve Doun Velocity Control) [99+99] Specifies the depth and direction of the effect that velocity will have on Curve Down. For the way in which the effect occurs, refer to Velocity (page 36 of this manual).

21c: String Picking Position [099]

Specifies the location at which the string will be plucked. A setting of 0 is the end of the string, 50 is the middle of the string, and 99 is the other end of the string.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Picking Position.

Intensity (Picking Position AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

Damp [099] Specifies the amount of high-frequency attenuation that will be produced by the characteristics of the string and by how the string is pressed. As this value is increased, the high-frequency components of the vibration in the string will be attenuated (dampened) more strongly, producing a darker sound. In general, this parameter should be set to a higher value to simulate instruments which use soft strings or which have no frets, and to a lower value to simulate instruments which use hard strings or which have frets.

2:1 OSC 1 (12: Plucked String Model)

Param eters

Prog. Edit P2

Envelope of the attack waveform Volume level

Attack Curve Up Attack Curve Down

KTr (Damp Keyboard Track) [99+99] Specifies how the Damp amount will be affected by the keyboard location. With positive (+) settings, the Damp value will increase as you play notes above C4. With negative () settings, the Damp will decrease as you play notes above C4.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Damp.

Intensity (Damp AMS Intensity) [99+99] Specifies the depth and direction of the effect that AMS will have.

Decay [099] Specifies the decay time over which the sound will decay if you continue pressing a note. Higher settings of this value will produce a longer decay time.

Depending on the settings of 4-2: Amp EG, the setting you make here may not have audible results. If you raise the EG break level and sustain level, it will be easier to hear the result of this setting.

KTr (Decay Keyboard Track) [99+99] Specifies how the Decay amount will be affected by the keyboard location. With positive (+) settings, the decay will become faster as you play notes above C4. With negative () settings, it will become slower.

Release [099] Specifies the length of time over which the sound will decay after you release the note. Higher settings of this value will produce a longer release time.

Depending on the settings of 4-2: Amp EG, the setting you make here may not have audible results. You may need to raise the EG release level, it will be easier to hear the result of this setting.

2:1 OSC 1 (12: Plucked String Model)

when Damp=50 when Damp=75when Damp=25 C-1 C4 C9

99

0

50

C-1 C4 C9

99

0

75

C-1 C4 C9

99

0

25

+99 +50

0

-99 -50

+99 +50

0

-50 -99

+99

+50

-50 -99

0

Damp DampDamp

when Decay=50 when Decay=75when Decay=25 C-1 C4 C9

99

0

50

C-1 C4 C9

99

0

75

C-1 C4 C9

99

0

25

+99 +50

0

-99 -50

+99 +50

0

-50 -99

+99

+50

-50 -99

0

Decay DecayDecay

2:1 OSC 1 (12: Plucked String Model)

Param eters

Prog. Edit P2

Dispersion [099] Specifies the inharmonicity of the higher partials relative to the fundamental. With a value of 0, the partials will be located at integer (whole number) multiples of the fundamental. As this value is increased, the partials will move further away from integer multiple locations. In general, thin and flexible strings can be simulated by a low Dispersion value, and thick and stiff strings can be simulated by a high Dispersion value.

If this value is raised excessively, the pitch may become unstable.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Dispersion.

Intensity (Dispersion AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

21d: Harmonics

Position [099] Specifies the location at which the string will be pressed to play harmonics.

Control [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control the harmonics effect.

Intensity (Harmonics Control Intensity) [99+99] Specifies the depth and direction of the control that AMS will have on the harmonics effect.

When making the Position setting, you must assign Control to a controller other than OFF, and raise the Intensity value. The decay time of the harmonics effect will differ depending on the keyboard location that you play.

21e: Pickup

Pickup If this is checked, the sound will be passed through a simulated pickup. If this is not checked, the sound will remain unchanged.

Position, AMS, and Intensity can be set when Pickup has been checked.

Position [099] Adjusts the change in tone that results from differences in pickup location.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (p64) that will control Pickup.

Intensity (Pickup Position AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

21f: Low EQ

Frequency [049] Specifies the cutoff frequency of the Low EQ.

Gain [18+18] Specifies the gain of the Low EQ.

Low Boost [099] Specifies how the low frequency range will be emphasized. Raising this value will cause the low frequency range to be emphasized more strongly.

13: Bowed String Model This oscillator is a physical model which simulates the sound of a bowed string instrument such as a violin or cello. By controlling the bowing speed and the bowing pressure, you can create performance expressions that are very close to those of an actual bowed string instrument.

21a: Bowing Speed EG [EG 1EG 4, Amp EG]

Selects the EG which will control bowing speed (the speed at which the bow moves across the string).

Int. (Speed Modulation EG Intensity) [99+99] Specifies the depth and direction of the effect of EG With negative () settings, the direction of the bow speed will be inverted.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control bowing speed. Instead of using an EG to modify the bowing speed, you can use the Ribbon Controller or Joy Stick to simulate bowing without using an EG.

Int. (Speed AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control bowing speed.

Int. (Speed AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.2.

2:1 OSC 1 (13: Bowed String Model)

Parameters related to the string String Damp Dispersion

String vibration

String

Bow

Position

Bow Speed

Pressure

Bridge Reflection

Bridge Reflection

Bowed String Model

Bowed String Model Peaking EQ

21a

21b

21c

21d

2:1 OSC 1 (13: Bowed String Model)

Param eters

Prog. Edit P2

Differential If this is not checked, the value produced by EG, AMS.1 and AMS.2 will be used as the bowing speed. If you wish to use EG to control the bowing speed, leave this item un-checked. If this is checked, the rate of change of EG, AMS.1 and AMS.2 will be used as the bowing speed.

Using the ribbon controller to control bowing speed As an example, we will assume that you have set AMS.1 to Ribbon (X). In order to control bowing speed using the ribbon controller alone, raise the Int. (Speed AMS.1 Intensity) value, and set Int. (Speed Modulation EG Intensity) to 0. Check Differential. When you are pressing the ribbon controller, the bowing speed will be zero, so there will be no sound. As you slide your finger toward the right over the ribbon controller, the speed at which your finger moves will be the bowing speed, and sound will be produced. As you slide your finger to left and right, the bowing speed will change from positive zero negative zeropositive, allowing you to produce performance expressions that are very similar to those of actually moving a bow back and forth.

Rosin [099] Specifies the coefficient of static friction between the bow and the string. (This corresponds to the amount of rosin on the bow.) Higher values will increase the friction between the bow and string. When this value is in the region of 0, it will be difficult for playing strength to be transmitted to the string.

21b: Bow Pressure EG [EG 1EG 4, Amp EG]

Selects the EG which will control the pressure of the bow on the string (bow pressure).

Int. (Press Modulation EG) [99+99] Specifies the depth and direction of the effect that the EG will have on bow pressure. If this value is low, the bow will rest lightly on the string.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control bow pressure.

Int.(Press AMS Intensity) [99+99] Specifies the depth of the effect produced by AMS.

21c: String Bowing Position [099]

Specifies the location at which the bow contacts the string. A setting of 0 is the end of the string, 50 is near the middle, and 99 is at the other end.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Bowing Position. Changing the location at which the string is bowed will also change the overtone structure.

Int. (Bowing Position AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

Damp [099] Specifies how the high frequency components will be attenuated by the characteristics of the string and by the way in which the string is pressed onto the fingerboard of the violin or cello. As this value is increased, the high frequency components of the wave transmitted along the string will be attenuated more greatly, producing a darker sound. In general, you should use higher values to simulate instruments which have flexible strings or unfretted instruments, and lower values to simulate instruments with stiff strings or fretted instruments.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Damp.

Int. (Damp AMS Intensity) [99+99] Specifies the depth and direction of the effect of Damping Mod.Source.

Damp KTr Key [C1G9] Specifies the key above and below which keyboard tracking will begin to apply to the Damp effect.

Low Int [99+99] Specifies the depth and direction in which the Damp amount will change for notes below the Damp KTr Key. Positive (+) settings will cause Damp to increase for notes below the Damp KTr Key. Negative () settings will cause Damp to decrease for notes below the Damp KTr Key.

High Int [99+99] Specifies the depth and direction in which the Damp amount will change for notes above the Damp KTr Key. Positive (+) settings will cause Damp to increase for notes above the Damp KTr Key. Negative () settings will cause Damping to decrease for notes above the Damping KTr Key.

Dispersion [099] Specifies the inharmonicity of the higher partials relative to the fundamental. With a value of 0, the partials will be located at integer (whole number)x multiples of the fundamental. As this value is increased, the partials will move further away from integer multiple locations. In general, thin and flexible strings can be simulated by a low Dispersion value, and thick and stiff strings can be simulated by a high Dispersion value.

If this value is raised excessively, the pitch may become unstable.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Dispersion.

Intensity (Dispersion AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

Bridge Reflection [099] Specifies the amount of the wave that will be reflected at the end of the string. Higher values will make the notes sound more easily. With a setting of 0 there will be no reflection at all.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control Bridge Reflection.

Int. (Bridge Reflection AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS.

21d: Peaking EQ

Frequency [049] Specifies the center frequency at which the peaking EQ will boost (attenuate) the sound.

Q [029] Specifies the width of the region that will be boosted (attenuated) by the peaking EQ. With a setting of 0, a wide region will be affected. With a setting of 29, only a narrow region close to the center frequency will be boosted (attenuated).

Gain [18+18] Specifies the gain by which the peaking EQ will boost or attenuate.

22: OSC 2 OSC2 parameters have the same structure as OSC1 parameters. Refer to 2-1: OSC 1.

2:1 OSC 1 (13: Bowed String Model), 2-2: OSC 2

23: Sub/Noise Here, you can make settings for the sub-oscillator and the noise generator. The sub oscillator lets you select one of four basic waveforms. In the mixer section, the signal from the sub oscillator is mixed with the signals of oscillators 1 and 2. The noise generator produces white noise. The noise signal that is generated passes through a dedicated filter, and is mixed by the mixer section with the signals from the sub oscillator and oscillators 1 and 2.

23a: Sub Oscillator

Wave Form [Saw, Square, Triangle, Sine] Specifies the type of filter that will be applied to the output from the noise generator.

2-3: Sub/Noise

Param eters

Prog. Edit P2

Noise Generator

Cutoff Frequency Resonance

Low Pass

High Pass

Band Pass

Thru

Filter Type Input Trim

Noise Filter

23a

23b

Saw Square Triangle Sine

2-3: Sub/Noise

23b: Noise Generator Here, you can make various settings for the noise generator.

Filter Type [Thru, Low Pass, High Pass, Band Pass] Selects the type of filter that will be applied to the output of the noise generator. When Thru is selected, the Input Trim, Frequency, AMS.1, Intensity (Cutoff Frequency AMS.1 Intensity), AMS.2, Intensity (Cutoff Frequency AMS.2 Intensity), and Resonance settings will be unavailable.

Input Trim [099] Specifies the input level to the dedicated noise filter.

Cutoff Frequency [099] Specifies the cutoff frequency of the noise signal filter. For the characteristics of each filter type, refer to 3- 2b:Filter1 (page 47 of this manual).

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control the Cutoff Frequency.

Intensity (Cutoff Frequency AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.1.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control the Cutoff Frequency.

Intensity (Cutoff Frequency AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect of AMS.2.

Resonance [099] This boosts the frequency region specified by the Cutoff Frequency to add character to the sound. Since the filter characteristics differ from the filter type of the 3-2b: Filter 1 , 3-4b: Filter 2 the resulting effect will be different even if Type, Cutoff Frequency and Resonance settings are identical.

3-1: Mixer

Param eters

Prog. Edit P3

Program Edit P3 Here, you can make settings for the mixer and filter. For the way in which the mixer, filter and amp sections are connected, refer to 3-2a: Filter Routing.

31: Mixer The mixer allows you to set the levels at which the five signals (OSC 1, OSC 2, Noise Generator, Feedback, Sub OSC) will be combined into the two mixer outputs. You can also select a modulation source to control each level, and specify its intensity.

31a: OSC 1 Out 1 These parameters adjust the level at which the oscillator 1 signal is output from mixer output 1, and specify a modulation source that will control this level.

Output Level [00...99] Specifies the signal level that will be output to mixer output 1.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control output level.

Intensity (Level AMS Intensity) [99...+99] Specifies the depth and direction of the effect of AMS. With positive (+) settings, higher values of the modulation source will increase the output level. With negative () settings, lower values of the modulation source will increase the output level. If EG or LFO has been selected as the AMS, positive (+) settings will cause the original phase of the EG or LFO to be used, and negative () settings will invert the phase.

OSC1

OSC2

Sub OSC

Noise Generator

Feed back

Mixer Out1

Mixer Out2

OSC1 Mixer Out1 Level OSC1 Mixer Out2 Level

31a 31b 31c 31d 31e 31f 31g 31h 31i 31j

31b: OSC 1 Out 2 These parameters adjust the level at which the oscillator 1 signal is output from mixer output 2, and specify a modulation source that will control this level. Refer to the above explanation of 3-1a: OSC1 OUT1.

31c: OSC 2 Out 1 These parameters adjust the level at which the oscillator 2 signal is output from mixer output 1, and specify a modulation source that will control this level. Refer to the above explanation of 3-1a: OSC1 OUT1.

31d: OSC 2 Out 2 These parameters adjust the level at which the oscillator 2 signal is output from mixer output 2, and specify a modulation source that will control this level. Refer to the above explanation of 3-1a: OSC1 OUT1.

31e: Sub Out 1 These parameters adjust the level at which the sub oscillator signal output is output from mixer output 1, and specify a modulation source that will control this level. Refer to the above explanation of 3-1a: OSC1 OUT1.

31f: Sub Out 2 These parameters adjust the level at which the sub oscillator signal output is output from mixer output 2, and specify a modulation source that will control this level. Refer to the above explanation of 3-1a: OSC1 OUT1.

31g: Noise Out 1 These parameters adjust the level at which the output of the noise generator is output from mixer output 1, and specify a modulation source that will control this level. Refer to the above explanation of 3-1a: OSC1 OUT1.

31h: Noise Out 2 These parameters adjust the level at which the output of the noise generator is output from mixer output 2, and specify a modulation source that will control this level. Refer to the above explanation of 3-1a: OSC1 OUT1.

31i: Feedback Out 1 These parameters adjust the level at which the feedback from the amp section is output from mixer output 1, and specify a modulation source that will control this level. Refer to the above explanation of 3-1a: OSC1 OUT1.

Raising the Feedback level excessively may cause the sound to distort.

31j: Feedback Out 2 These parameters adjust the level at which the feedback from the amp section is output from mixer output 2, and specify a modulation source that will control this level. Refer to the above explanation of 3-1a: OSC1 OUT1.

Raising the Feedback level excessively may cause the sound to distort.

3-1: Mixer

3-2: Filter 1

Param eters

Prog. Edit P3

32: Filter 1 Here, you can make settings for one of the two multi-mode filters. Each multi-mode filter can be set to one of five filter types.

32a: Routing (Filter Routing) [serial 1/serial 2/parallel] Use the radio buttons to select the way in which filters 1 and 2 will be combined. The connections from mixer output filter amp can be routed in the following three ways.

Multimode Filter

Low Pass High Pass Band Pass Band Reject Dual BPF

Filter TypeInput Trim Cutoff Frequency

Resonance

32a 32b 32c

32d

32e

Serial1

Parallel

Mixer Output1

Mixer Output2

Filter1 Filter2 Amp1

Amp2

Mixer Output1

Mixer Output2

Filter1 Filter2 Amp1

Amp2

Mixer Output1

Mixer Output2

Filter1

Filter2

Amp1

Amp2

Serial2

32b: Filter 1

Type [Low Pass, High Pass, Band Pass, Band Reject, Dual BPF] Selects the filter type. When Dual BPF is selected, the 3-3: Filter 1 SUB parameters can also be set. When you select Dual BPF, the 3- 2c: Cutoff and 3-2e: Resonance parameter names will change to Cutoff A and Resonance A respectively.

Input Trim [099] Specifies the level of the input to filter 1.

If this value is raised, the sound may become distorted if the resonance setting is high, etc.

32c: Cutoff/Cutoff A (Cutoff Frequency) Frequency [099]

Specifies the cutoff frequency of filter 1. As this value is increased, the cutoff frequency will rise. Since the BPF and Dual BPF filter types use filters with differing characteristics, their actual cutoff frequency may differ even if their settings are identical.

EG (Cutoff Frequency Modulation EG) [EG1EG4, Amp EG] Selects the EG that will create time-varying change in the cutoff frequency of filter 1.

Intensity (Cutoff Frequency Mod. EG Intensity) [99+99] Specifies the depth and direction of the control that EG (Cutoff Frequency Modulation EG) will have on the cutoff frequency. With positive (+) settings of this parameter, the tone will become brighter when the various EG levels rise into the + area (the setting of the Frequency will be reached when the EG levels are at 0), and darker when the EG levels fall into the area. With negative () settings of this parameter, the tonal change will take place in the opposite direction.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control Frequency.

Intensity (Cutoff Frequency AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect that AMS.1 will have on the cutoff frequency.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control Frequency.

Intensity (Cutoff Frequency AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect that AMS.2 will have on the cutoff frequency.

Filter Types and Cutoff Frequency

Low Pass Filter (LPF)

Dual Band Pass Filter (Dual BPF)

Cutoff Frequency A

Cutoff Frequency B

A low pass filter is the most commonly-used type of filter, and passes the range of frequencies that lie below the cutoff frequency, and cuts the high range. Cutting the higher partials will cause a bright sound to become darker (more mellow).

A high pass filter passes the range of frequencies that lie above the cutoff frequency, and cuts the low range. This type of filter is used when you wish to make the sound thinner. However, raising the cutoff frequency excessively will drastically reduce the volume.

A band pass filter passes the range of frequencies in the vicinity of the cutoff frequency, and cuts the ranges above and below. This type of filter is used when you wish to emphasize a particular portion of the sound.

The dual band pass filter places two band pass filters in parallel. It allows you to simulate sounds such as human voice and the body resonances of a violin or guitar.

Band Pass Filter (BPF)

High Pass Filter (HPF )

Cutoff Frequency

A band reject filter cuts only the range in the vicinity of the cutoff frequency, and passes the rest of the sound. This type of filter gives a unique character to the sound.

Band Reject Filter (BRF)

Cutoff Frequency

Cutoff Frequency

Cutoff Frequency

frequency

frequency

frequency

frequency

frequency

3-2: Filter 1

32d: Keyboard Track Keyboard tracking settings specify how the cutoff frequency of filter 1 will be varied according to keyboard position.

Low Key [C-1G9] Specifies the key at which Lower keyboard tracking will begin.

High Key [C-1G9] Specifies the key at which Higher keyboard tracking will begin.

Low Int. [99+99] Specifies the depth and direction of cutoff frequency change that will occur below the Low Key. With a setting of 50, the change will match the change in pitch.

High Int. [99+99] Specifies the depth and direction of cutoff frequency change that will occur above the High Key. With a setting of +50, the change will match the change in pitch.

32e: Resonance/Resonance A Resonance [099]

This setting emphasizes the overtones in the region of the Frequency to add character to the sound. Higher values will produce a stronger effect. With high settings of resonance, the output signal of the filter may distort. If this occurs, reduce the Input Trim setting. With the Dual BPF filter type, the overtones in the vicinity of each cutoff frequency will be affected in the same way as by a BPF.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control the amount of resonance.

Intensity (Resonance AMS Intensity) [99+99] Specifies the depth and direction of the effect that AMS will have on the amount of resonance.

3-2: Filter 1

Param eters

Prog. Edit P3

Cutoff frequency

C-1 C4 C9

Int=-50

Int= 0

Int> 0

Low Key

High Key

Int=0

Int=+50

Int=+99

Int<0 Int=-99

Low resonance value High resonance value

The effect of resonance Low Pass

High Pass

Band Pass

Band Reject

33: Filter 1SUB If the 3-2b: Filter 1 Type parameter was set to Dual BPF, you can make settings for the 3-3: Filter 1 SUB parameters.

33a: Input Trim [099] Specifies the level of the input to filter 1.

If this value is raised, the sound may become distorted if the resonance setting is high, etc.

33b: Cutoff B (Cutoff Frequency B) Frequency [099]

Specifies the cutoff frequency of filter 1. As this value is increased, the cutoff frequency will rise. Since the BPF and Dual BPF filter types use filters with differing characteristics, their actual cutoff frequency may differ even if their settings are identical.

EG Intensity (Cutoff Frequency Modulation EG Intensity) [99+99] Specifies the depth and direction of the effect that the EG specified by 3-2: Filter 1 will have on the cutoff frequency. With positive (+) settings of this parameter, positive (+) EG levels will make the sound brighter relative to the value specified by Frequency, and negative () EG levels will make the sound darker. (When an EG level is 0, the value specified by Frequency will be used unchanged.) With negative () settings of this parameter, the change will take place in the opposite direction of positive (+) settings.

AMS.1 Intensity [99+99] Specifies the depth and direction of the effect that the AMS.1 specified in 3-2c: Cutoff will have on the cutoff frequency.

AMS.2 Intensity [99+99] Specifies the depth and direction of the effect that the AMS.2 specified in 3-2c: Cutoff will have on the cutoff frequency.

It is not possible to change EG, AMS.1 or AMS.2 in the Filter 1 SUB page.

33c: Keyboard Track Keyboard tracking settings specify how the cutoff frequency of filter 1 will be varied according to keyboard position.

Low Key [C-1G9] Specifies the key at which Lower keyboard tracking will begin.

High Key [C-1G9] Specifies the key at which Higher keyboard tracking will begin.

3-3: Filter 1 SUB

33a 33b

33c

33d

Low Int. [99+99] Specifies the depth and direction of cutoff frequency change that will occur below the Low Key. With a setting of 50, the change will match the change in pitch.

High Int. [99+99] Specifies the depth and direction of cutoff frequency change that will occur above the High Key. With a setting of +50, the change will match the change in pitch.

33d: Resonance B

Resonance [099] This setting emphasizes the overtones in the region of the Frequency to add character to the sound. Higher values will produce a stronger effect. With high settings of resonance, the output signal of the filter may distort. If this occurs, reduce the Input Trim setting. With the Dual BPF filter type, the overtones in the vicinity of each cutoff frequency will be affected in the same way as by a BPF.

AMS Intensity [99+99] Specifies the depth and direction of the effect that the AMS specified in 3-2e: Resonance will have on the resonance.

3-3: Filter 1 SUB

Param eters

Prog. Edit P3

34: Filter 2 Here, you can make settings for one of the two multi-mode filters. Each multi-mode filter can be set to one of five filter types.

34a: Link to Filter 1 If this is checked, Filter 2 will be linked to Filter 1, and the following settings will be the same as the settings of Filter 1. If this is not checked, the following parameters can be set for Filter 2. For details on these parameters, refer to 3-2: Filter 1.

34b: Filter 2

34c: Cutoff/Cutoff A (Cutoff Frequency)

34d: Keyboard Track

34e: Resonance/Resonance A

35: Filter 2 SUB When 3-4b: Filter 2 Type parameter is set to Dual BPF, you will be able to set various parameters for 3-5: Filter 2 SUB. For details on these parameters, refer to 3-3: Filter 1 SUB.

If 3-4a: Link to Filter 1 is checked, it is not possible to make 3-5: Filter 2 SUB settings.

3-4: Filter 2, 3-5: Filter 2 SUB

34a 34b

34c

34d

34e

Program Edit P4 Here, you can make volume-related settings. There are two independent amps, and the signals which are input to each amp are determined by the setting of 3-2a: Routing (page 47 of this manual).

41: Amp

41a: Amp 1

Amplitude [099] Specifies the volume level of amp 1. The input signal to amp 1 is determined by the 3-2a:Routing setting

EG (Amplitude Modulation EG) [EG1EG4, Amp EG] Selects the EG that will create time-variant change in the volume level of amp 1. For the settings of each EG, refer to Program Edit P5.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control the volume level of amp 1.

Intensity (Amplitude AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS on the volume level.

41b: Keyboard Track (Amplitude 1 Keyboard Track)

Low Key [C-1G9] Specifies the key at which Lower keyboard tracking will begin.

High Key [C-1G9] Specifies the key at which Higher keyboard tracking will begin.

Low Int. [99+99] Specifies the way in which keyboard tracking will affect the volume of notes below the Low Key.

4-1: Amp

Param eters

Prog. Edit P4

41a

41b

41c

41d

41e

High Int. [99+99] Specifies the way in which keyboard tracking will affect the volume of notes below the High Key.

If Low Int. or High Int. are set to positive(+) settings, you will need to lower the 4-1a: Amp 1 Amplitude value.

41c: Amp 2 Here you can adjust the settings for Amp 2. These parameters have the same structure as the 4-1a: Amp 1 parameters.

41d: Keyboard Track (Amplitude 2 Keyboard Track) Here you can adjust keyboard tracking settings for Amp 2. These parameters have the same structure as the 4-1b: Keyboard Track parameters.

41e: Pan/Outputs

Pan [OFF, L000C064R127] This sets the panning for input to the insert effect. If you are not using an insert effect, this sets the panning to output jacks 1/L/MONO and 2/R. With a setting of OFF, the sound will not be output to 1/L/MONO and 2/R. L is left, C is center, and R is right.

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects the modulation source (page 36 of this manual) that will move the panning of amp 1 relative to the Pan setting.

Intensity (Panpot AMS Intensity) [99+99] Specifies the depth and direction of the effect of AMS on the panning.

Output Level [0127] Specifies the output level following the amp.

Send 1 [0127] Send 2 [0127]

Here, you can specify the input levels to the master effects when insertion effects are not used. If you are using insertion effects, the input levels to the master effects are specified by the 7-1b: Pan/Width/ Send 1, 2 parameters Send 1 and 2 (page 41 in Parameter Guide).

In all modes, you must use an insertion effect when using bank M programs. If you do not use an insertion effect, the output level will be decreased.

4-1: Amp

Volume level

C-1 C4 C9

Int=-50

Int= 0

Int> 0

Low Key

High Key

Int=0

Int=+50

Int=+99

Int<0 Int=-99

4-2: Amp EG Here, you can make settings for the Amp EG. The Amp EG lets you specify how the sound will change over time. Since the Amp EG can also be used as a general-purpose controller, it can create time-variant change in parameters other than volume.

42a: Level (Amp EG Level) [099]

Attack (Attack Level) [099] Specifies the volume that will be reached after the Attack Time has elapsed.

Break (Break Level) [099] Specifies the volume level that will be reached after the Decay Time has elapsed.

Sustain (Sustain Level) [099] Specifies the volume level that will be reached after the Slope Time has elapsed.

42b: Time (Amp EG Time)

Attack (Attack Time) [099] Specifies the time from note-on (when a note is played) until the volume reaches the attack level. With a value of 0, the volume will change instantly. With a value of 99, the volume will change slowly.

Decay (Decay Time) [099] Specifies the time from when the attack time ends until the break level is reached.

Slope (Slope Time) [099] Specifies the time from when the decay time ends until the sustain level is reached.

Release (Release Time) [099] Specifies the time from note-off (when a note is released) until the volume falls to zero.

4-2: Amp EG

Param eters

Prog. Edit P4

AMSource

Note-off Attack level Sustain level

Note-on

Attack time

Decay time

Slope time

Release time

Time Break level

Volume

Time-variant change in volume created by the amp EG

42a 42b

42c 42d 42e

42c: Level Control

Velocity [99+99] Specifies the depth and direction of the effect that velocity will have on the level of the amp EG.

42d: Level Modulation

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control the level of the Amp EG.

Intensity (EG Level AMS Intensity) [99+99] Specifies the depth and direction of the effect that AMS will have on the level of the Amp EG.

42e: Time Modulation

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control the Amp EG times.

Intensity (EG Time AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect that AMS.1 will have on the Amp EG times.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control the Amp EG times.

At (Attack Time AMS.2 Intensity) [99+99] Dc (Decay Time AMS.2 Intensity) [99+99] Sl (Slope Time AMS.2 Intensity) [99+99] Rl (Release Time AMS.2 Intensity) [99+99]

Specifies the depth and direction of the effect that AMS.2 will have on each EG time.

4-2: Amp EG

When " Velocity" is set to a positive (+) value

Note-on Note-off

Note-on

Note-off

Note-on Note-off

Settings of the Amp EG Softly played notes Strongly played notes

When the various EG times are set to negative () values

Note-on Note-off

Note-on Note-off

Note-on Note-off

Settings of the Amp EG Softly played notes Strongly played notes

Program Edit P5 This section provides four general purpose EGs (envelope generators). The four EGs can be used as modulation sources for the parameters of other sections to create time-variant change in the sound.

51: EG 1

51a: Level

Start (Start Level) [99+99] Specifies the value at the time of note-on.

Attack (Attack Level) [99+99] Specifies the value that will be reached after the Attack Time has elapsed.

Break (Break Level) [99+99] Specifies the value that will be reached after the Decay Time has elapsed.

Sustain (Sustain Level) [99+99] Specifies the value that will be reached after the Slope Time has elapsed.

Release (Release Level) [99+99] Specifies the value that will be reached after the Release Time has elapsed.

51b: Time (Amp EG Time)

Attack (Attack Time) [099] Specifies the time from note-on (when a note is played) until the value reaches the attack level. With a value of 0, the value will change instantly. With a value of 99, the value will change slowly.

5-1: EG 1

Param eters

Prog. Edit P5

Note-off Attack level Sustain level

Note-on

Attack time

Decay time

Slope time

Release time

Time

Break level

0

-99

+99

51a 51b

51c 51d

51e

AMSource

Decay (Decay Time) [099] Specifies the time from when the attack time ends until the Break Level is reached.

Slope (Slope Time) [099] Specifies the time from when the decay time ends until the Sustain Level is reached.

Release (Slope Time) [099] Specifies the time from note-off (when a note is released) until the Release Level is reached.

51c: Level Control

Velocity [99+99] Specifies the depth and direction of the effect that velocity will have on the EG levels.

51d:Level Modulation

AMS (Alternate Modulation Source) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control the level of EG1.

Intensity (EG Level AMS Intensity) [99+99] Specifies the depth and direction of the effect that AMS will have on the EG levels.

51e: Time Modulation

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source 1 (page 64 of this manual) that will control the EG1 times.

Intensity (EG Time AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect that AMS.1 will have on the EG times.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control the EG1 times.

At (Attack Time AMS.2 Intensity) [99+99] Dc (Decay Time AMS.2 Intensity) [99+99] Sl (Slope Time AMS.2 Intensity) [99+99] Rl (Release Time AMS.2 Intensity) [99+99]

Specifies the depth and direction of the effect that AMS.2 will have on each EG time.

5-1: EG 1

When "Velocity" is set to a positive (+) value

Note-on Note-off

Note-on

Note-off

Note-on Note-off

Settings of EG1 Softly played notes Strongly played notes

When the various EG times are set to negative () values Note-on

Note-off Note-on

Note-off Note-on

Note-off

Settings of EG1 Softly played notes Strongly played notes

5-2: EG 2, 5-3: EG 3, 5-4: EG 4

Param eters

Prog. Edit P5

52: EG 2

53: EG 3

54: EG 4 EG 2, EG 3 and EG 4 have the same parameters as EG 1. Refer to 5-1: EG 1.

AMSource

AMSource

AMSource

Program Edit P6 This section provides four LFOs (Low Frequency Oscillators). These LFOs can be used as modulation sources for parameters of other sections, to create cyclic changes in the sound.

61: LFO 1

61a: Wave Form/Key Sync

Wave Form [Triangle 0ExpSawDown] Settings for the general-purpose LFOs

6-1: LFO 1

AMSource

61a

61b

61c

61d

Random 2 changes in a straight line toward a value which is determined randomly every 1/2 cycle.

Amplitude and the duration at which each level is held will both change randomly (sample & hold).

When Key Sync=ON, the starting phase will vary randomly.

16: Exp Saw Up

17: Exp Saw Down

15: Exp Tri

11: Step Tri 4

12: Step Tri 6

14: Step Saw 6

2: Tri Random

3: Sine

0: Triangle 0

4: Saw Up 0

5: Saw Up 180

6: Saw Down 0

7: Saw Down 180

8: Square

1/2 cycle

10: Random2 (Vector)

9: Random1(S/H)

1: Triangle 90

13: Step Saw 4

6-1: LFO 1

Param eters

Prog. Edit P6

Key Sync [OFF/by TIMBRE/by VOICE] Use the radio buttons to select the key sync setting (i.e., whether or not the phase of the LFO waveform will be returned to its initial state when a note-on occurs). OFF : The LFO will operate (cycle) regardless of note-on. by TIMBRE : Key sync will occur for the LFOs of all voices at the time of the first note-on that occurs in a state when no keys are on. by VOICE :Key sync will occur independently for the individual LFO of the voice for which note-on occurred.

61b: Frequency If you used the radio buttons to select Frequency, set the following parameters to specify the LFO frequency.

F (Frequency) [0(0Hz)199(60Hz)] Specifies the frequency of the LFO.

AMS.1 (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Select a modulation source 1 (page 64 of this manual) that will control the LFO frequency.

Intensity (Frequency AMS.1 Intensity) [99+99] Specifies the depth and direction of the effect that AMS.1 will have on the F (Frequency) value.

AMS.2 (Alternate Modulation Source 2) [OFFMIDI (CC#83)] Selects a modulation source 2 (page 64 of this manual) that will control the LFO frequency.

Intensity (Frequency AMS.2 Intensity) [99+99] Specifies the depth and direction of the effect that AMS.2 will have on the F (Frequency) value.

61c: MIDI Sync If you used the radio buttons to select MIDI Sync, set the following parameters to synchronize the LFO frequency to MIDI Clock.

When the Global mode parameter 1-1d: MIDI Clock (page 119 in Parameter Guide) is set to Internal the LFO will synchronize to the tempo specified by Prog. Temp, and if it is set to External the LFO will synchronize to the MIDI Clock messages received from an External MIDI device.

MIDI Sync Base [ 3 3 3 ] MIDI Sync Time [116]

This is relative to the tempo determined by the MIDI clock, these settings specify the note length (Base) and its multiple (Time) that will set the period of the synchronized LFO. For example if MIDI Sync Base is (quarter note) and MIDI Sync Time is 4, the LFO period will be four beats.

Prog. Temp [40240] Selects the tempo that will be used when MIDI Clock is set to Internal.

Note-On

Key Sync SW = Off

Key Sync SW = byTIMBRE / byVOICE

Note-On

Note-On Note-On

61d: Amplitude Modulation

AMS (Alternate Modulation Source 1) [OFFMIDI (CC#83)] Selects a modulation source (page 64 of this manual) that will control the amplitude of the LFO waveform.

Intensity (Amplitude AMS Intensity) [99+99] Specifies the depth and direction of the effect that AMS will have on the amplitude of the LFO waveform.

Offset [50+50] Specifies the center value of the LFO waveform.

Fade In Time [099] Specifies the time over which the amplitude of the LFO will increase from 0 until it reaches the maximum

value.

62: LFO 2

63: LFO 3

64: LFO 4 LFO 2, LFO 3, and LFO 4 have the same parameter as LFO 1. Refer to 6-1: LFO 1

6-1: LFO 1, 6-2: LFO 2, 6-3: LFO 3, 6-4: LFO 4

The parameter value being modulated

LFO movement determined by Modulation Intensity

The parameter value being modulated

LFO movement determined by Modulation Intensity

The parameter value being modulated

LFO movement determined by Modulation Intensity

Offset = 0

Offset = 50

Offset = -50

AMSource

AMSource

AMSource

Program Edit P7 Here, you can make settings for the insertion effects. For details on the parameters etc., refer to Parameter Guide page 44, Program Edit P7.

Program Edit P8 Here, you can make settings for the master effects. For details on the parameters etc., refer to Parameter Guide page 44 Program Edit P7.

Program Edit P7, Program Edit P8

Param eters

Prog. Edit P7/8

Modulation Source List 00: OFF 01: EG 1 02: EG 2 03: EG 3 04: EG 4 05: Amp EG 06: LFO 1 07: LFO 2 08: LFO 3 09: LFO 4 10: Portamento 11: Velocity (Soft) 12: Velocity (Medium) 13: Velocity (Hard) 14: Note Number(Linear) 15: Note Number(Exp) 16: Note Split(Hi) 17: Note Split(Low) 18: After Touch 19: Joy Stick (X) 20: Joy Stick (+Y) 21: Joy Stick (-Y)

*22: AfterTouch+JS(+Y) 23: Ribbon (X) 24: Ribbon (+X) 25: Ribbon (-X) 26: Ribbon (Z) 27: Foot Pedal (CC#04) 28: Value Slider(CC#18) 29: MIDI (CC#19) 30: SW1 (CC#80) 31: SW2 (CC#81) 32: Foot SW (CC#82) 33: MIDI (CC#83)

* This After Touch is half of the effect of 18:AfterTouch.

Retrigger Controller List 00: OFF 01: Velocity (Soft) 02: Velocity (Medium) 03: Velocity (Hard) 04: Note Number(Linear) 05: Note Number(Exp) 06: After Touch 07: Joy Stick (X) 08: Joy Stick (+Y) 09: Joy Stick (-Y) 10: AfterTouch+JS(+Y) 11: Ribbon (X) 12: Ribbon (+X) 13: Ribbon (-X) 14: Ribbon (Z) 15: Foot Pedal (CC#04) 16: Value Slider(CC#18) 17: MIDI (CC#19) 18: SW1 (CC#80) 19: SW2 (CC#81) 20: Foot SW (CC#82) 21: MIDI (CC#83)

Data

4. Data

Data

Precautions Regarding program change (MIDI) reception Depending on the oscillator type used by a program, some time may be required after a program change is received until a bank M program is actually selected. When selecting programs, please leave ample time between the program change and the following note-on.

Regarding noise The effect settings and the parameter settings of the oscillator used by the program may affect each other so as to cause noise to appear in the sound. Also, if a program is played immediately (less than one second) after it is selected, noise may appear in the output sound.

Data dump compatibility The bank M programs created using MOSS are not compatible with the Prophecy or Z1.

Please use an insertion effect with the program In all modes (Program, Combination, Sequencer), be sure to use an insertion effect when using a bank M program. If you do not use an insertion effect, the output of the bank M program will diminish.

When MIDI Clock Source is set to Internal If a bank M program is selected for any timbre in a combination, the D-mod Src Tempo for the AMS or effect of the timbre program will use the Prog. Tempo setting (page 61 of this manual).

SOLO-TRI convert sounds (SOLO_TRI.PCG) The SOLO_TRI.PCG sounds in the included disk are data which was created to allow the SOLO-TRI preset sounds (page 14 of this manual) to be simulated on the MOSS-TRI. For some sounds, the audible result may n

Manualsnet FAQs

If you want to find out how the MOSS-TRI KORG works, you can view and download the KORG MOSS-TRI User's Guide on the Manualsnet website.

Yes, we have the User's Guide for KORG MOSS-TRI as well as other KORG manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Guide should include all the details that are needed to use a KORG MOSS-TRI. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the KORG MOSS-TRI User's Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This KORG MOSS-TRI User's Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download KORG MOSS-TRI User's Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print KORG MOSS-TRI User's Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the KORG MOSS-TRI User's Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.