Contents

KORG nanoKONTROL Studio Owner's Manual PDF

1 of 20
1 of 20

Summary of Content for KORG nanoKONTROL Studio Owner's Manual PDF

2

Table of Contents Main Features .................................................................. 3 Preparation ...................................................................... 4

Using a Wireless Connection .................................... 4 Using a USB Connection ............................................ 5

Part names ...................................................................... 6 Operating Modes and Software Setup ........................ 7

nanoKONTROL Studio Modes .................................. 7 Setup for using the nanoKONTROL Studio in the DAW Mixer Control Mode .......................................... 7 Setup for using the nanoKONTROL Studio in the Assignable Mode ......................................................... 9

Customizing Controllers ..............................................10 KORG KONTROL Editor Software ...........................10 Types of Parameters ..................................................10 Scene Parameters ....................................................... 11 Global Parameters ..................................................... 14

Appendix ......................................................................... 17 Restoring the Factory Settings ............................... 17 Troubleshooting.......................................................... 17

Specifications ................................................................ 19 Operating requirements ........................................... 19

Thank you for purchasing the Korg nanoKONTROL Studio Mobile MIDI controller.

In order to use this product in a computer music environment, youll need to adjust the MIDI settings of the host application. Please follow the directions in the host applications owners manu- al to difine these settings.

Apple, iPad, iPhone, Mac, iOS and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.

Windows is a trademark of Microsoft Corporation in the U.S. and other countries.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

All product names and company names are the trademarks or registered trademarks of their respective owners.

3

Main Features

Fast, Simple Setup with Immediate Support for Multiple DAW Systems and Sequencing Software The nanoKONTROL Studio comes equipped with multiple DAW set- tings, so setup can be easily completed without the need for setting up each individual controller. Compatible software: Cubase, Digital Performer, GarageBand, Live, Logic, Pro Tools, SONAR, Studio One.

5 Programmable Scene Memories of fer Instant Access to Your Favorite Settings Take control of your entire computer music system! The nanoKONTROL Studio allows you to create five entirely different software-specific scenes and instantly switch between them. The nanoKONTROL Studio can control all of your favorite software syn- thesizersand your DAW systeminstantly.

Convenient USB and Wireless Compatibility with Both Desktop Computers and Mobile Devices The nanoKONTROL Studio is equipped to provide both USB and wireless connections so you can select the optimal method for your operating environment. A USB connection is useful when you are planning to spend a lot of time using the nanoKONTROL Studio with a desktop computer and do not wish to worry about the battery power level; or, you can eliminate cable-clutter and create a wireless connection between your iPhone, iPad, and/or Mac/Windows com- puter. The built-in wireless system is easy to use and simple to set up.

4

Preparation

Using a Wireless Connection Installing Batteries Make sure that the mode switch is set to Standby, and then slide out the battery cover on the rear to open it. Making sure to observe the correct polarity, insert the batteries, and then close the battery cover.

If a malfunction occurs that cannot be resolved no matter how many times the nanoKONTROL Studio is turned off, then on, remove the batteries, and then install them again.

Turning On the Power Set the mode switch to (Battery). The nanoKONTROL Studio turns on (Battery mode).

When using the nanoKONTROL Studio with the mode switch set to (Battery), the batteries will become de- pleted, even with a USB connection. In addition, the nanoKONTROL Studio cannot be used as a USB-MIDI de- vice, even if it is connected to a computer using a USB ca- ble.

(Battery)

nanoKONTROL Studio

Turning Off the Power Set the mode switch to Standby. The nanoKONTROL Studio and the power LED turn off.

Auto Power-Off Function In Battery mode, the nanoKONTROL Studio is automatically

turned off if no operation is performed for an extended period of time. ( page.15: Auto Power Off)

5

Wireless Connection Setup In order to use the nanoKONTROL Studio wirelessly, a wireless con-

nection must be established. Refer to Using a wireless connection in the Quick Start Guide to set up the wireless connection.

With an iPhone/iPad or Mac, a wireless connection must be established each time.

Wireless Operation with USB Power The wireless function of the nanoKONTROL Studio can be used in combination with a USB connection. While power is supplied from the USB port of the computer, the wireless function of the nanoKONTROL Studio can be used to connect it to an iPhone/iPad, etc.

Turning the Wireless Feature On and Off While holding down the Scene button, press the Cycle transport button to turn the wireless feature On or Off. TIP When the mode switch is set to (Battery), the wireless

function cannot be turned off. If the nanoKONTROL Studio is being used in an environ-

ment where radio waves cannot be transmitted, turn off the wireless function.

Using a USB Connection Making Connections and Turning On the Power

1. Set the mode switch to (USB).

2. Use the included USB cable to connect the nanoKONTROL Studio to a USB port on your computer. The nanoKONTROL Studio turns on, and the power LED lights up.

The included USB cable must be used. In order to use the nanoKONTROL Studio functions, set-

tings must be specified to match your app. Refer to the Owners Manual and specify the settings.

TIP When you first connect the nanoKONTROL Studio to your Windows computer, a driver will be installed automatically.

TIP With the driver pre-installed with Windows, nanoKONTROL Studio cannot be used by multiple applica- tions simultaneously. If you want to use the nanoKONTROL Studio with multiple applications simultane- ously, you must install the KORG USB-MIDI driver. Download the KORG USB-MIDI driver from the Korg website. (http://www.korg.com/)

Turning Off the Power Set the mode switch to Standby. The nanoKONTROL Studio and the power LED turn off.

6

Part names

1

2

3 4

5

6 7

8

9

10 11 12 13

14

15

1. Mode switch

2. USB port

3. Scene LEDs

4. Scene button

5. Transport buttons

6. Track / buttons

7. Marker buttons

8. Jog wheel

9. Power LED

10. Mute buttons

11. Solo buttons

12. Rec buttons

13. Select buttons

14. Knobs

15. Sliders

7

Operating Modes and Software Setup

nanoKONTROL Studio Modes The nanoKONTROL Studio can operate in the following modes. Se- lect the mode according to your application.

DAW Mixer Control Mode In this mode, the controllers of the nanoKONTROL Studio will be automatically set up for mixer control by the DAW software. You can control the level of each channel or operate transport controls such as mute/solo and play/stop.

Assignable Mode In this mode, MIDI control change messages are assigned to the controllers of the nanoKONTROL Studio. By sending MIDI control change messages that correspond with the parameters that you wish to control, you can easily use the nanoKONTROL Studio to control your software synthesizer or DAW software, for example.

Setup for using the nanoKONTROL Studio in the DAW Mixer Control Mode The following are examples of the setup procedures for various DAW software titles. For details on specifying settings and using the DAW software, refer to the instruction manual for the software.

Cubase 1. While holding down the Scene and Marker Set buttons, turn

on the nanoKONTROL Studio to set it to Cubase mode. Once the nanoKONTROL Studio has been set to Cubase mode, it will continue operating in that mode.

2. In Cubase, open Device Setup, and then add Mackie Con- trol to Devices.

3. Open the page for the added Mackie Control, and then se- lect the nanoKONTROL Studio ports as the MIDI input and output ports to be used.

4. Open the MIDI Port Setup page, and then clear the In All MIDI Inputs check box for nanoKONTROL Studio.

Digital Performer 1. While holding down the Scene and Marker buttons, turn

on the nanoKONTROL Studio to set it to Digital Performer mode. Once the nanoKONTROL Studio has been set to Digi-

8

tal Performer mode, it will continue operating in that mode. Using a USB connection

Open Applications Utilities, start Audio MIDI Setup, open the MIDI Studio window, and then click Add Device.

Specify an appropriate name for the device to be added. (Example: nanoKONTROL Studio DP)

Connect the added device to the nanoKONTROL Studio, as shown on the left.

2. In Digital Performer, open the Control Surface window, and then select Mackie Control for Driver and Unit.

3. Select the nanoKONTROL Studio port for MIDI.

Button operations with Digital Performer With Digital Performer, the Cycle button turns on/off Memory Cycle. However, the Cycle button will not light up when Memory Cycle is turned on. TIP The Marker Set button does not operate with Digital Per-

former. TIP The jog wheel works only when the Scrub function is

turned on. To use the Scrub function, set the nanoKONTROL Studio global parameter Use Scene Button as Scrub to Enable.

Live 1. While holding down the Scene and Marker buttons, turn

on the nanoKONTROL Studio to set it to Live mode.Once

the nanoKONTROL Studio has been set to Live mode, it will continue operating in that mode.

2. In Live, open the Preferences window, and then select Mackie Control for Control Surface.

3. Select the nanoKONTROL Studio ports for the MIDI input and output ports to be used by Mackie Control.

GarageBand/Logic Download the nanoKONTROL Studio Control Surface plug-in from the Korg website (http://www.korg.com/), and then set it according to the instructions in the supplied document.

Pro Tools 1. While holding down the Scene and (Rewind) buttons,

turn on the nanoKONTROL Studio to set it to Pro Tools mode. Once the nanoKONTROL Studio has been set to Pro Tools mode, it will continue operating in that mode.

2. In Pro Tools, open the Peripherals window, and then se- lect HUI for Type.

3. Select the nanoKONTROL Studio ports for the sending and receiving ports to be used by HUI.

SONAR 1. While holding down the Scene and (Forward) buttons,

turn on the nanoKONTROL Studio to set it to SONAR mode. Once the nanoKONTROL Studio has been set to SONAR mode, it will continue operating in that mode.

2. In SONAR, open the Preferences window, select the

9

nanoKONTROL Studio port check boxes for both Inputs and Outputs in the Devices page, and then click the Apply button.

3. In the Control Surfaces page, click the Add New Control- ler/Surface button to open the Controller/Surface Set- tings dialog box, and then select Mackie Control for Controller/Surface and the nanoKONTROL Studio ports for Input Port and Output Port.

TIP The Marker Set button does not operate with SONAR. TIP As a default in SONAR, the Select button does not function.

Launch SONAR, open the Mackie Control properties from the ATC module in the Control Bar, and then select the Se- lect highlights track check box.

Studio One 1. While holding down the Scene and Track buttons, turn on

the nanoKONTROL Studio to set it to Studio One mode. Once the nanoKONTROL Studio has been set to Studio One mode, it will continue operating in that mode.

2. In Studio One, open the Preferences, and then click the Add... button in the External Devices to open the Add Device dialog box.

3. Select Mackie Control, select the nanoKONTROL Studio ports for Receive From and Send To, and then click the OK button.

TIP The Scrub function does not operate with Studio One.

Setup for using the nanoKONTROL Studio in the Assignable Mode nanoKONTROL Studio setup While holding down the Scene and Cycle buttons, turn the nanoKONTROL Studio on to set it to assignable mode. Once the nanoKONTROL Studio has been set to the assignable mode, it will continue operating in that mode.

Application setup In this mode, MIDI control change messages are assigned to the controllers of the nanoKONTROL Studio. By sending MIDI control change messages that correspond with the parameters that you wish to control, you can easily use the nanoKONTROL Studio to control your software synthesizer or DAW software, for example.

TIP The method and procedure for linking messages with param- eters will differ depending on the software you are using, so please refer to the instruction manual for your software.

About Scenes Groups of settings assigned to the controllers can be saved as one of the five user-configurable Scenes available on the nanoKONTROL Studio. This way, you can create Scenes to control your different software synthesizers and DAW system, and then switch between then instantly.

Switching scenes Each press of the Scene button advances to the next Scene in a cycli- cal order.

10

Customizing Controllers

KORG KONTROL Editor Software The KORG KONTROL Editor software is required to customize the operation of the nanoKONTROL Studio. Download the software from the Korg website (http://www.korg.com/), and install the soft- ware by following the instructions in the supplied document.

TIP For details on installing and using the KORG KONTROL Edi- tor software, refer to the instruction manual for that soft- ware.

Types of Parameters The nanoKONTROL Studio contains two types of customizable pa- rameters. Scene Parameters address the function of specific con- trollers inside of the selected Scene. Global Parameters control the overall operation of the nanoKONTROL Studio, regardless of the selected scene.

Scene Parameters These parameters determine what the nanoKONTROL Studio does when you operate a controller in assignable mode. Five scene parameters can be saved on the nanoKONTROL Studio. By preparing scene parameters for each software that you use, you can instantly switch the settings.

Global Parameters These parameters specify general behavior of the nanoKONTROL Studio, such as energy-saving features. The global parameters will be shared among all scenes.

11

Scene Parameters Knobs

Knob Enable ........................................... [Enable, Disable] This parameter specifies whether the Knob operations are en- abled or disabled. When set to Disable, a MIDI message will not be transmitted, even if you operate a Knob.

MIDI Channel ............................................. [1...16, Global] This parameter specifies which MIDI channel is used to transmit MIDI messages from the Knobs. When set to Global, MIDI mes- sages will be transmitted on the Global MIDI Channel, specified in the global parameters. ( page.14: Global MIDI Channel)

CC Number ........................................................... [0...127] This parameter specifies the CC number of the control change message that will be transmitted.

Left Value ............................................................. [0...127] This parameter specifies the value of the control change mes- sage that is transmitted when you turn the Knob fully to the left.

Right Value ............................................................ [0...127] This parameter specifies the value of the control change mes- sage that is transmitted when you turn the Knob fully to the right.

Slider

Slider Enable .......................................... [Enable, Disable] This parameter specifies whether the Slider operations are enabled or disabled. When set to Disable, a MIDI message will not be transmitted, even if you operate a Slider.

MIDI Channel ............................................. [1...16, Global] This parameter specifies which MIDI channel is used to transmit MIDI messages from the Sliders. When set to Global, MIDI messages will be transmitted on the Global MIDI Channel, specified in the global parameters.

CC Number ........................................................... [0...127] This parameter specifies the CC number of the control change message that will be transmitted.

Lower Value ........................................................... [0...127] This parameter specifies the value of the control change mes- sage that is transmitted when you move the Slider to its lowest position.

Upper Value .......................................................... [0...127] This parameter specifies the value of the control change mes- sage that is transmitted when you move the Slider to its highest position.

12

Buttons

Assign Type ............... [Note, Control Change, No Assign] This parameter specifies the MIDI messages assigned to but- tons.

Note (Note# C-1 to G9) Note messages will be transmitted. Specify the note number to be transmitted. Up to four note numbers can be assigned.

Control Change (CC# 0 to 127)

Control change messages will be transmitted. Specify the control change number to be transmitted.

No Assign No MIDI message will be transmitted.

MIDI Channel ............................................. [1...16, Global] This parameter specifies which MIDI channel is used to transmit MIDI messages. When set to Global, MIDI messages will be transmitted on the Global MIDI Channel, specified in the global parameters.

Off Value ................................................................ [0...127] This parameter specifies the value of the message that is trans- mitted when the button is switched off.

On Value ................................................................ [0...127] This parameter specifies the value of the message that is trans- mitted when the button is switched on. When Assign Type is set to Note, a note-on message is transmitted with the On Value as the velocity. When On Value is set to 0, a note-on message is transmitted with 1 as the velocity.

Button Behavior ............................. [Momentary, Toggle] The button can be set to either of these modes:

Momentary When Assign Type is set to Note, a note-on message is transmitted when you press the Button, and a note-off message is transmitted when you release the Button. When Assign Type is set to Control Change, a control change message with a value of 127 is transmitted when you press the Button, and a control change message with a value of 0 is transmitted when you release the Button.

Toggle When Assign Type is set to Note, each press of the Button will alternately send a note-on message or a note-off message. When Assign Type is set to Control Change, each press of the Button will alternately send a control change message with a value of 127 or 0.

Jog Wheel

Jog Wheel Type ..... [Inc/Dec Button 1, Inc/Dec Button 2, Continuous, Sign Magnitude, No Assign] This parameter specifies the transmission of MIDI messages when you turn the Jog Wheel.

Inc/Dec Button 1 Inc/Dec Button 2

Control change messages will be transmitted with a different CC number depending on whether the jog dial is turned clockwise or counterclockwise. This can be used, for example, to control the playback location with the forward and back buttons. When set to Inc/Dec Button 1, a control change message with the value 127 (equivalent to turning on the button) is transmitted when you turn the Jog Wheel. When set to Inc/Dec Button 2, a control change message with the value 127 (equivalent to turning on the button) or with the value 0 (equivalent to turning off the button) is transmitted when you turn the Jog Wheel.

Continuous Control change messages will be transmitted continuously. Turning the Jog Wheel clockwise increases the value, and turning the Jog Wheel counterclockwise reduces the value.

13

Sign Magnitude Control change messages with the values 1 through 64 will be trans- mitted when the Jog Wheel is turned clockwise and with the values 65 through 127 will be transmitted when the Jog Wheel is turned counterclockwise.

No Assign No MIDI message will be transmitted.

MIDI Channel ............................................. [1...16, Global] This parameter specifies which MIDI channel is used to transmit MIDI messages from the Jog Wheel. When set to Global, MIDI messages will be transmitted on the Global MIDI Channel, speci- fied in the global parameters.

Acceleration ................................................... [1, 2, Const] This parameter specifies the degree of acceleration when the Jog Wheel is turned quickly. When set to 2, the acceleration is greater than when set to 1. When set to Const, the speed will remain constant regard- less of the acceleration used to turn the Jog Wheel.

CC Number ........................................................... [0...127] This parameter specifies the CC number of the control change message that will be transmitted. Specify one control change number when Jog Wheel Type has been set to Sign Magni- tude or Continuous, or specify one control change number for CW (clockwise) and one for CCW (counterclockwise) when Jog Wheel Type has been set to Inc/Dec Button 1/2.

Min Value ............................................................. [0...127] This parameter specifies the minimum control change value

that is transmitted when Jog Wheel Type has been set to Continuous.

Max Value ............................................................. [0...127] This parameter specifies the maximum control change value that is transmitted when Jog Wheel Type has been set to Continuous.

14

LED

LED Mode ............................................. Internal, External] This parameter specifies whether the LEDs light up in response to you pushing a button, or whether they will light up in re- sponse to receiving a MIDI message from the computer. Normal- ly, this is set to Internal; however, by specifying the appropri- ate settings, the nanoKONTROL Studio can behave as if it is fully integrated with your softwareprovided the software can send MIDI messages.

Internal The LEDs light up in response to the buttons being operated manually.

External The LEDs light up or go off when a message with the control change number or note number assigned to a button is received from the computer. When an On Value or note-on message is received, the LED lights up. When an Off Value or note-off message is received, the LED turns off.

When selecting a new Scene, all of the LEDs will turn off.

Global Parameters General

Global MIDI Channel ............................................. [1...16] This parameter specifies the Global MIDI channel that the nanoKONTROL Studio is operating on. This can be set to match the MIDI channel of your software.

Controller Mode ................................................................. [Assignable, Cubase/Digital Performer/Live/Pro Tools/ SONAR/Studio One] The nanoKONTROL Studio has operating modes that are specif- ically designed for controlling popular DAW programs, as well as a Assignable mode that lets you assign a control change mes- sage to each controller. Choose the setting thats appropriate for the software that youre using. For details on how to use

each operating mode, please refer to Operating Modes and Software Setup (page 7).

Assignable Each of the nanoKONTROL Studios controllers will transmit the control change message that youve assigned.

Cubase/Digital Perform- er/Live/Pro Tools/ SONAR /Studio One

The nanoKONTROL Studio will function with settings suitable for controlling the specified DAW program. Choose the setting thats appropriate for the software that youre using.

Battery Type ........................................... [Alkaline, Ni-MH] Be sure to use this parameter to specify the type of batteries you have installed in the nanoKONTROL Studio. Set this to Ni-

MH when using nickel-metal hydride batteries or to Alkaline when using alkaline batteries.

15

Use Scene Button as Scrub ....................[Disable/Enable] This parameter specifies whether the Scene button is used as the Scrub function in DAW mixer control mode. Choose En- able if you want to use this button as the Scrub function, or Disable if you dont want to use it.

The Scrub function might not work depending on the DAW that youre using.

Wireless

Device Name This parameter specifies the device name displayed when a wireless connection is being used. Up to 25 alphanumeric characters can be entered. TIP This setting will be applied the next time that the

nanoKONTROL Studio is turned on or the next time that the wireless function is turned on ( page.4: Using a Wireless Connection).

Energy-saving features

Auto Power Off .......... [Disable, 30 min, 1 hour, 2 hours, 4 hours] When operating on batteries, the nanoKONTROL Studio can be set to automatically turn off after a set period of inactivity to preserve the battery life. You can choose the amount of time that must pass with no activity before the power will automati- cally turn off30 minutes, 1 hour, 2 hours, or 4 hours. To prevent the nanoKONTROL Studio from turning off automatically, set the Auto Power Off to Disable. To turn the nanoKONTROL Studio back on after the Auto Power Off func- tion has turned it off, set the mode switch to Standby, and then return it to (Battery).

Auto LED Off .......................................... [Disable, Enable] By setting this parameter to Enable, you can choose to have the LEDs automatically decrease in brightness after a set period of inactivity; and then turn off completely after an additional set period of time where there is no activity. This setting is applied whether the nanoKONTROL Studio is operating with a USB connection or on batteries.

LED Brightness ......................................................... [1...3] This parameter specifies the maximum brightness of the LEDs. 1 indicates the least bright, and 3 indicates the maximum brightness. This setting is applied whether the nanoKONTROL Studio is operating with a USB connection or on batteries.

16

When the nanoKONTROL Studio is operating on batteries, the brighter the LEDs, the shorter the battery life. In order

to extend the battery life, specify a lower setting.

LED Illumination ................................... [Disable, Enable] This parameter can be used to activate the nanoKONTROL Studio LED illumination after a set period of time has passed with no operations being performed. Set this to Enable so that the LEDs will light up or to Disable so that they will not light up. If the nanoKONTROL Studio is operated while the LED Illumination is active, it will return to its previous condition. This setting is applied whether the nanoKONTROL Studio is operating with a USB connection or on batteries.

17

Appendix

Restoring the Factory Settings While holding down the Scene, and Stop buttons, turn the nanoKONTROL Studio On. The Scene button and Scene LEDs 1 through 5 begin to blink. All settings of the nanoKONTROL Studio will be restored to the factory settings when the blinking stops.

Restoring the factory settings takes several seconds after the nanoKONTROL Studio is turned on. Never turn off the nanoKONTROL Studio while the Scene button and Scene LEDs 1 through 5 are blinking.

The factory settings cannot be restored when the mode

switch is set to (Battery).

Troubleshooting Check the Korg website (http://www.korg.com/) for the most recent FAQ.

The nanoKONTROL Studio wont turn on. With a USB connection If the nanoKONTROL Studio is connected to a computer via a

USB hub, the nanoKONTROL Studio may not turn on due to insuf- ficient power. In that case, the nanoKONTROL Studio should be connected directly to the USB connector on the computer with- out using a USB hub.

There may be a problem with the USB cable currently used. Check if the nanoKONTROL Studio can be turned on using the supplied USB cable.

With a wireless connection Make sure that the Mode switch is set to (Battery). Make sure that the batteries have been inserted correctly, and

that they are not depleted. If the batteries are depleted, replace them with new ones.

A wireless connection cannot be established. Verify that your computer or iPhone/iPad is compatible with Blue-

tooth 4.0. Verify that the operating system for your computer or iPhone/

iPad is compatible with Bluetooth Low Energy MIDI. Compatible

18

operating systems are Mac OS X Yosemite or later, Windows 8.1 or later (KORG BLE-MIDI Driver is required), and iOS 8.0 or later.

The wireless connection cuts out. Make sure that your computer or iPhone/iPad is not too far away

from the nanoKONTROL Studio.

There is no response from the software. Make sure that the nanoKONTROL Studio is correctly specified in

the MIDI port setup of your software. In order to use the functions of the nanoKONTROL Studio, your

software must be set up. For the setup, refer to Operating Modes and Software Setup on page 7 and the instruction manual for your software.

Your software may not support some functions. Check the in- struction manual for your software.

Buttons do not operate as indicated by the nanoKONTROL Studio. Your software may not support some functions or may operate

differently. Be sure that the nanoKONTROL Studio is in a mode compatible

with your software. (page.7: Operating Modes and Soft- ware Setup)

The software does not respond to the transmit- ted MIDI message. Verify the MIDI channel for messages transmitted by the

nanoKONTROL Studio is set to the same MIDI channel in your software.

If DAW software is being used, setup may be necessary in order to use the nanoKONTROL Studio. For the setup, refer to Operat- ing Modes and Software Setup on page 7 and the instruc- tion manual for your DAW software.

The LED of a button does not light up when the button is pressed. Check the settings for Controller Mode (page 14) and LED

Mode (page 14).

19

Specifications Wireless method: Bluetooth low energy Jacks: USB port (micro Type B) Power supply: USB bus power supply or two AAA batter-

ies (alkaline or nickel-metal hydride bat- teries)

Battery service life: Approx. 10 hours (when using alkaline batteries: Battery life will vary depending on the batteries used and on the condi- tions of use.)

Current consumption: 500 mA or less Dimensions (W x D x H): 278 x 160 x 33 mm/ 10.94 x 6.29 x 1.29 Weight: 459 g/1.01 lbs (excluding batteries) Included items: Two AAA alkaline batteries, USB cable,

Quick Start Guide

* For the purpose of improvement, the specifications and appearance are subject to change without notice.

Operating requirements Windows (USB connection):

Microsoft Windows 7 SP1 or later (32 bit/64 bit)

Windows (wireless connection): Computer installed with Microsoft Win- dows 8.1 or later and compatible with Bluetooth 4.0 (KORG BLE-MIDI Driver is required)

Mac (USB connection): OS X 10.9 Mavericks or later Mac (wireless connection): Mac installed with OS X 10.10 Yosemite or

later and compatible with Bluetooth 4.0 iOS (wireless connection): iPhone/iPad installed with iOS 8 or later

Manualsnet FAQs

If you want to find out how the nanoKONTROL Studio KORG works, you can view and download the KORG nanoKONTROL Studio Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for KORG nanoKONTROL Studio as well as other KORG manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a KORG nanoKONTROL Studio. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the KORG nanoKONTROL Studio Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This KORG nanoKONTROL Studio Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download KORG nanoKONTROL Studio Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print KORG nanoKONTROL Studio Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the KORG nanoKONTROL Studio Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.