Contents

KORG K-Series K61p Owner's Manual PDF

1 of 73
1 of 73

Summary of Content for KORG K-Series K61p Owner's Manual PDF

Owners Manual Manuel dutilisation Bedienungsanleitung

Table of Contents

Precautions............................................................................ 3 Introduction ........................................................................... 4

Main Features ...........................................................................................4 Controllers and their Functions ................................................................4

Setup ...................................................................................... 7 Installing the MIDI driver and softwares ...................................................7 Making connections and turning on the power .........................................8 About the K-Series and the driver ports .................................................10 About K-Series MIDI OUT connector .....................................................10 Restoring the factory preset programs ...................................................11

Operation ............................................................................. 12 Keyboard ................................................................................................12 ClickPoint ................................................................................................12 KNOB1 and KNOB2 ...............................................................................12 SW1 and SW2 ........................................................................................13 OCTAVE SHIFT UP / OCTAVE SHIFT DOWN .......................................13 PITCH wheel ..........................................................................................13 MOD wheel .............................................................................................14 SLIDER ..................................................................................................14 PEDAL ....................................................................................................14

Using the K61Ps Internal Sounds ..................................... 15 Selecting a sound ...................................................................................15 Effects .....................................................................................................15 Setting mode ..........................................................................................16 Program change enable/disable .............................................................20

Troubleshooting .................................................................. 22 Specifications ...................................................................... 23

3

Owners Manual

Precautions Location Using the unit in the following locations can result in a malfunction. In direct sunlight Locations of extreme temperature or humidity Excessively dusty or dirty locations Locations of excessive vibration Close to magnetic fields

Power supply Please connect the designated AC adapter to an AC outlet of the correct voltage. Do not connect it to an AC outlet of voltage other than that for which your unit is intended.

Interference with other electrical devices Radios and televisions placed nearby may experi- ence reception interference. Operate this unit at a suitable distance from radios and televisions.

Handling To avoid breakage, do not apply excessive force to the switches or controls.

Care If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid cleaners such as ben- zene or thinner, or cleaning compounds or flam- mable polishes.

Keep this manual After reading this manual, please keep it for later reference.

Keeping foreign matter out of your equipment Never set any container with liquid in it near this equipment. If liquid gets into the equipment, it could cause a breakdown, fire, or electrical shock. Be careful not to let metal objects get into the equipment. If something does slip into the equip- ment, unplug the AC adapter from the wall outlet. Then contact your nearest Korg dealer or the store where the equipment was purchased.

THE FCC REGULATION WARNING (for U.S.A.) This equipment has been tested and found to com- ply with the limits for a Class B digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal- lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no guarantee that inter- ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be de- termined by turning the equipment off and on, the user is encouraged to try to correct the interfer- ence by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equip-

ment and receiver. Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help.

Unauthorized changes or modification to this sys- tem can void the users authority to operate this equipment.

CE mark for European Harmonized Standards CE mark which is attached to our companys prod- ucts of AC mains operated apparatus until De- cember 31, 1996 means it conforms to EMC Di- rective (89/336/EEC) and CE mark Directive (93/ 68/EEC). And, CE mark which is attached after January 1, 1997 means it conforms to EMC Directive (89/336/ EEC), CE mark Directive (93/68/EEC) and Low Voltage Directive (73/23/EEC). Also, CE mark which is attached to our companys products of Battery operated apparatus means it conforms to EMC Directive (89/336/EEC) and CE mark Directive (93/68/EEC).

IMPORTANT NOTICE TO CONSUMERS This product has been manufactured according to strict specifications and voltage requirements that are applicable in the country in which it is in- tended that this product should be used. If you have purchased this product via the internet, through mail order, and/or via a telephone sale, you must verify that this product is intended to be used in the country in which you reside. WARNING: Use of this product in any country other than that for which it is intended could be dangerous and could invalidate the manufacturers or distributors warranty. Please also retain your receipt as proof of pur- chase otherwise your product may be disqualified from the manufacturers or distributors warranty. Company names, product names, and names of formats etc. are the trademarks or registered trade- marks of their respective owners.

* Company names, product names, and names of formats etc. are the trademarks or regis- tered trademarks of their respective owners.

4

Introduction

Thank you for purchasing this K-Series USB/MIDI Studio Controller. For trouble-free enjoyment of this controller, please read this manual carefully and use the product only as directed. Keep this manual in a safe place where you can easily refer to it in the future. This manual applies to the K25, K49, and K61. There is a special section that covers the additional features of the K61P.

Main Features Equipped with a variety of expressive and powerful controllers.

ClickPoint provides two simultaneous controllers (X and Y), and also serves as a mouse for your software applications.

Korgs M1 Le software synthesizer is included with your K-Series controller, so you can enjoy playing and creating high quality sounds immediately.

The K61P contains an internal sound engine (borrowed form Korgs digital piano series) capable of producing 24 high fidelity sounds - including piano, electric pi- ano, organs and more.

Controllers and their Functions

1

2

3 4 5

6 7 8 K61P Controller

5

Owners Manual

1. Keyboard The keyboard features full-size, velocity-sensing keys.

2. ClickPoint Two modes allow the ClickPoint controller to behave as an X - Y realtime controller, or as a clickable cursor/mouse when working with Softsynths or DAW software running on a computer.

3. KNOB1 / KNOB2 With MIDI control assignment, KNOB1/KNOB2 can be used to operate connected external MIDI equipment and software synthesizer such as DAW running on PC.

4. SW1 / SW2 These two assignable switches can be assigned independently to any MIDI control change number, allowing you to control other MIDI devices or music software pro- grams. They can also be used as Up 1 and Down 1 buttons when selecting pro- grams (Program Change).

5. OCTAVE SHIFT UP / OCTAVE SHIFT DOWN The octave buttons shift the pitch up and down in units of one octave.

6. PITCH wheel The Pitch Bend Wheel provides a smooth, continuous up or down change in pitch, that can be controlled in realtime.

7. MOD wheel The Modulation Wheel can be assigned to any MIDI control change number, al- lowing you to control other MIDI devices or music software programs.

8. SLIDER The Slider can be assigned to any MIDI control change number, allowing you to control other MIDI devices or music software programs, and is especially handy for functions such as volume and expression.

Sound Generator(K61P)

1 2 3 4 5

1. VOLUME knob This knob controls the volume of the internal sound engine. This sound is sent from the OUTPUT jacks (L/MONO,R) and the HEADPHONE jack.

2. BANK button The 24 internal sounds are arranged in three banks, each containing eight sounds. This button selects the current bank.

6

3. PROGRAM buttons Use one of these buttons to select a sound from within the current bank.

4. REVERB button This button is used to select the depth of the reverb effect, and to turn it on and off.

5. CHORUS button This button is used to select the depth of the chorus effect, and to turn it on and off.

Rear panel

1 2 3 4 5 6 7

Illustration shows the rear panel of K61P.

1. OUTPUT jacks (K61P only) These are the output jacks of internal sound engine. These can be connected to an amplifier, audio monitoring system, or to an audio recording device.

2. HEADPHONES jack (K61P only) This jack is provided so that you can listen to the internal sound engine through a set of stereo headphone (standard plug).

3. PEDAL jack An optional momentary pedal (such as the Korg PS-2 pedal switch) can be con- nected to the pedal jack. The K-Series will automatically detect the polarity of the pedal when the power is turned on.

4. MIDI OUT connector The MIDI out jack provides direct control of other MIDI equipped sound modules or audio devices. (P.10 About the K-Series MIDI OUT connector)

5. USB connector The USB connector allows your K-Series controller to communicate directly with your computer.

6. Power switch This switch turns the K-Series on by selecting either DC(Adapter) or USB power.When not in use, this switch places the K-Series in the standby mode. (p.8 Making connections and turning on the power)

7. Power supply connector Connect the optional AC adapter here. For ultimate convenience, the K-Series controllers can be powered directly from the USB bus - in most cases. In situations using an unpowered USB hub, or when controlling a MIDI module, you may wish to use an AC adapter.

7

Owners Manual

Setup

Installing the MIDI driver and softwares Contents of the CD-ROM The included CD-ROM contains the follwing.

K-Series editor KORG M1 Le software synthesizer KORG USB-MIDI driver for Windows XP Installation guide K-Series editor owners manual M1 Le software synthesizer owners manual Software license

Operating requirements Mac OS X users Computer

Apple Macintosh computer with a USB port that satisfies the operating require- ments of Mac OS X

Supported operating systems Mac OS X ver.10.3 or later

Windows XP users

Computer A computer with a USB port, that satisfies the operating requirements of Microsoft Windows XP (USB chipset made by Intel Corporation is recommended)

Supported operating systems Microsoft Windows XP Home Edition/Professional Service pack 1 or later

Install On the CD-ROM included with your K-Series controller, please refer to the installation instructions regarding the installation of the KORG USB-MIDI Driver for Windows XP, the K-Series Editor, and the M1 Le software synthesizer.

Please read before use Copyright to all software pertaining to this product is the property of Korg Corpora-

tion. A license agreement for the software pertaining to this product is included separately.

You must read this license agreement before you install the software. Your installation of the software will be taken to indicate your acceptance of the agreement.

Apple, Macintosh and Mac OS are registered trademarks of Apple Computer, Inc. Windows XP is a registered trademark of Microsoft Corporation in the U.S. and

other countries. All other product and company names are trademarks or registered trademarks of

their respective holders.

8

Making connections and turning on the power Be sure all your equipment is turned off BEFORE you begin hooking everything up. You must excercise caution, otherwise you may damage your speaker system or cause other malfunctions.

Connections using USB 1 Use a USB cable to connect the K-Series to the USB connector of your computer.

2 If you want to use a pedal, connect it to the PEDAL jack.

The K-Series will detect the polarity of the pedal when the power is turned on. Therefore, if a pedal is connected, do not hold it down while you turn the power on.

3 To turn on the power, set the K-Series power switch to the USB position.

Pedal switch

PEDAL jack

Power switch position

USB cable

Computer

USB connector

4 When you are ready to turn off the power, set the power switch to STANDBY.

If youre using a USB connection, you generally dont need to use an AC adapter. However if your computer is low-powered, or if you are using a hub that is only bus- powered (rather than self-powered), sufficient power may not be supplied to the K- Series. In this case, use the optional AC adapter and set the power switch to the DC position.

When USB is connected, MIDI OUT jack does not send out MIDI messages from the K-Series keyboard and controller.

Connections using MIDI 1 Connect the plug of the optional AC adapter to the K-Series power connector, and

plug the adapter into an AC outlet.

2 Use a MIDI cable to connect the K-Series to your external MIDI sound module.

3 If you want to use an optional pedal, connect it to the pedal jack.

The K-Series will detect the polarity of the pedal when the power is turned on. Therefore, if a pedal is connected, do not hold it down while you turn the power on.

9

Owners Manual

4 Set the power switch to the DC position. The power LED will light. When the power is turned on, the most recently saved settings will be recalled automatically.

5 Turn on any external MIDI sound modules connected to your K-Series controller.

MIDI IN

MIDI OUT

Pedal switch

MIDI cable

External MIDI sound module

PEDAL jack

Power switch position

Plug the AC adaptor into an AC outlet

Power supply connector

6 When you are ready to turn off the power, turn off any external MIDI sound mod- ules first, and then set the K-Series power switch to STANDBY.

Using the internal sound engine [K61P only] 1 Connect the plug of the optional AC adapter to the K-Series power connector, and

plug the adapter into an AC outlet.

2 Using standard instrument cables with 1/4 plugs, connect the output jacks on the K61P to the inputs of your audio monitor system or audio recorder. When connect- ing only one output, use the L/MONO jack only.

Use the volume knob to adjust the level of the OUTPUT jacks.

3 Set the power switch to the DC position. The power LED will light.

4 Turn on your connected audio monitoring system.

Headphone

Amplified speakers HEADPHONES jackOUTPUT jack

INPUT

10

About the K-Series and the driver ports From the computers point-of-view, the K-Series provides 1 USB-MIDI port and 2 USB- MIDI out ports.

Keyboard/Slider/ Pitch,Mod wheel/ SW1/SW2/Pedal/ ClickPoint/ Dump data

The driver of the application on a computer K-series

MIDI OUT device

MIDI IN device

MIDI OUT

KBD/KNOB

SOUND/CTRL *1

MIDI OUT juck

Dump data Sound generator *2

*1 K25/49/61 is CTRL *2 K61P only

MIDI IN device KBD / KNOB This is used to receive MIDI messages from the keyboard and the various controllers on the K-Series. When operating a computer application from the K-Series, select this port as the applications MIDI input. KBD/KNOB is also used to receive scene data. Select this port as the K-Series Editors MIDI input.

MIDI OUT device MIDI OUT MIDI OUT transmits software MIDI OUT messages to K-Series' MIDI OUT jack, i.e transmits MIDI messages from a computer application to external MIDI equipment. When the K-Series is used as a USB-MIDI controller, select this port for computer applications MIDI output.

SOUND / CTRL (CTRL if K25/K49/K61) SOUND/CTRL is used to receive scene data from the computer. Select this port as the K-Series Editors MIDI input. In addition, this port is used to play notes on internal sound engine of the K61P.

About K-Series MIDI OUT connector When USB is not connected Sends MIDI messages from K-Series keyboard and controller.

When USB is connected Sends MIDI messages from computers MIDI OUT port. It will not send MIDI messages from K-Series keyboard and controller.

11

Owners Manual

Restoring the factory preset programs To restore the K-Series to the original factory settings, hold down SW1 and SW2 while turning on the power.

The controllers setting when factory is shipped

Controller Function

SW1 / SW2 Program change (-1/+1)

KNOB1 CC#074 (Cutoff)

KNOB2 CC#079 (EG Intensity)

SLIDER CC#007 (Volume)

PITCH wheel Fixed (Pitch Bend)

MOD wheel CC#001 (Modulation)

PEDAL CC#064 (Damper)

ClickPoint Mouse mode

* The parameters shown inside the brackets relate to the M1 Le.

12

Operation The K-Series editor software (included on the CD-ROM) is used to assign the control- ler settings and certain parameter values.

MIDI messages are sent using MIDI channel.

Keyboard Note messages are sent from the keyboard. Three velocity curves (and a constant 127 velocity) allow the keyboard response to be tailored to the performers playing style. The keyboard may be transposed by semitones into any musical key.

ClickPoint MIDI control changes can be assigned individually to the X direction (left/right) and the Y direction (up/down) to simultaneously control two parameters. In addition, the ClickPoint can be used as a computer mouse. The assignable values are No Assign/Control Change/Mouse.

No Assign No MIDI information is sent from this controller.

Control Change [0...127] Moving the ClickPoint controller will change the value of the parameters assigned to the X and Y axis The ClickPoint controller will return to the center position when its released. To lock the X and Y parameters at their current values, press down (Z axis) on the center switch of the ClickPoint. Press it again to unlock the X and Y values.

Mouse Mode When set to Mouse mode, the ClickPoint can be operates as a mouse and will control the cursor on computer screen. The ClickPoint switch functions as the mouse.

The Mouse Mode is only operative when the connected to a computer via USB.

KNOB1 and KNOB2 By assigning MIDI control changes, these knobs can be used to operate external MIDI equipment and control musical software applications. Each knob can be assigned indi- vidually. The assignable values are No Assign/Control Change.

No Assign No MIDI information is sent from this controller.

Control Change [0...127] Turning the knob will change the value of the assigned parameter.

13

Owners Manual

SW1 and SW2 These two switches can be assigned individually to send a specific value to a specific MIDI control change parameter. In fact, both an on and off value can be set. The switch type can be set to Momentary or Toggle. The assignable values on SW1 and SW2 are No Assign/Program Change/Control Change.

No Assign No MIDI information is sent from this controller.

Program Change Every time [SW1] is pressed, the program change number is decreased by 1. Every time [SW2] is pressed, the program change number is increased by 1. In addition, a program change message of 0 is sent if [SW1] are [SW2] are pressed simultaneously.

Control Change [0...127] SW1 and SW2 can be assigned MIDI control change parameters; Toggle or Momen- tary mode; plus an On Value and a Release Value. In Toggle mode, each time a switch is pressed, a MIDI control message is sent; each press will alternate between the On Value and the Release Value. In Momentary mode, the On Value MIDI control message is sent when the switch is pressed down, and a Off Value MIDI control message is sent when the switch is re- leased.

OCTAVE SHIFT UP / OCTAVE SHIFT DOWN These buttons can shift pitch of the keyboard in one octave units. The octave shift range is different depending on the keyboard length.

K-Series type Octave ranges

K25 -4...+4

K49 -4...+4

K61/K61P -3...+3

Key lights(status) Octave setting

Dark 0 octave

Green +1 / -1octave

Orange +2 / -2octave

Red +3 / -3octave

Red Flashing +4 / -4octave(K25/K49 only)

PITCH wheel Use the Pitch Bend Wheel to send MIDI pitch bend messages.

14

MOD wheel By assigning a MIDI control change number, the Modulation Wheel can be used to operate external MIDI equipment and control musical software applications. The assignable values are No Assign/Control Change/After touch.

No Assign No MIDI information is sent from this controller.

Control Change [0...127] Use the Mod Wheel to smoothly change the value of the assigned MIDI control change parameter.

After Touch Use the Mod Wheel to send channel AFTERTOUCH messages.

SLIDER By assigning a MIDI control change number, the Modulation Wheel can be used to operate external MIDI equipment and control musical software applications. The assignable values are No Assign/Control Change.

No Assign No MIDI information is sent from this controller.

Control Change [0...127] Use the slider to smoothly change the value of the assigned MIDI control change pa- rameter.

PEDAL An optional pedal switch can be assigned to send a specific value to a specific MIDI control change parameter. In fact, both an on and off value can be set. The switch type can be set to Momentary or Toggle. The assignable values are No Assign/Control Change.

No Assign No MIDI information is sent from this controller.

Control Change [0...127] The pedal is assigned to MIDI controls with Toggle/Momentary mode selection, On Value and Off Value. In Toggle mode every time press the pedal, MIDI control message with parameter On Value and Off Value will be sent in turn. In Momentary mode every time press the pedal, MIDI control message with param- eter On Value will be sent when press down and MIDI control message with parameter Off Value will be sent when releas up.

15

Owners Manual

Using the K61Ps Internal Sounds

Selecting a sound The 24 Internal sounds of the K61P are organized into three banks each containing eight sounds. To select a particular sound, you need to select a program button and a bank. For example, to select the Clavi sound, press the sixth program button from the left (the key will light). Then press the bank button to select BANK2.

1 Press the program key corresponding to the sound you want to select.

2 Press the bank button to select one of the three banks. Every time the bank key is pressed, the selected bank will switch from BANK1, BANK2 or BANK3. The selected bank will be shown by the bank lights. For example, to select the Clavi sound, press the sixth program key from the left to turn on the key light. Then press the bank key to select BANK2.

[PROGRAM] key

[PIANO 1]

[PIANO 2]

[PIANO 3]

[PIANO 4]

[PIANO 5]

[PIANO 6]

[HARPSI 1]

[HARPSI 2]

Bank2

E. Piano 1

E. Piano 2

Soft E.P.

Vintage E.P.

E.P. Pad

Clavi

Vibraphone

Choir

Bank3

Jazz Organ 1

Jazz Organ 2

Jazz Organ 3

Church Organ 1

Church Organ 2

Church Organ 3

Strings

Slow Strings

Osc#

2

2

1

1

2

1

1

2

Osc#

1

1

1

1

2

1

1

1

Osc#

2

2

2

3

1

1

1

2

Bank1

Grand Piano 1

Grand Piano 2

Standard Piano

Bright Piano

Honky Tonk Piano

Mellow Piano

Harpsichord 1

Harpsichord 2

Sound List

* [PROGRAM] key is BANK1s label. * Indicates the number of oscillators used to produce the voice.

Effects Reverb Reverb adds a concert hall ambience by simulating the echoes and sound reflection of such an environment.

1 Press the [REVERB] button to select one of the three reverb depths. The selected setting will be shown by the color of the [REVERB] button.

[REVERB] button lights Reverb depth

Dark Off

Green Light

Orange Standerd

Red Deep

16

Chorus Chorus adds a sense of depth and motion to the sound

1 Press the [CHORUS] button to select the depth of the chorus effect. The selected setting will be shown by the color of the [CHORUS] button.

[CHORUS] key Chorus depth

Dark Off

Green Light

Orange Standerd

Red Deep

Setting mode The Setting mode is used to access and change the settings of other features on the K61P. To enter the Setting mode, hold down the Bank button. The BANK lights and the 8 program button lights will turn off. Now you can use the 8 program buttons to select the function you want to change. The selected program button light will flash. Then press the note on the keyboard to set the value. When you are done, press the [BANK] button to exit the Setting mode. The eight items available in the Setting mode are shown below:

[PROGRAM] keys

[PIANO 1]

[PIANO 2]

[PIANO 3]

[PIANO 4]

[PIANO 5]

[PIANO 6]

[HARPSI 1]

[HARPSI 2]

Contents

Velocity Curve Setting

Transposing the Keyboard

Adjusting the Pitch

Selecting a Temperament

Changing the Global MIDI Channel Setting

The Local Control On/Off Setting

Enabling or Disabling Program Changes

Enabling or Disabling Volume Message Filter

Function

Velocity curve

Transpose

Pitch

Temperament

Global MIDI channel

Local control

Program Change Setting

Volume message filter

* [PROGRAM] key is BANK 1s lablel.

Velocity curve There are 3 velocity curves and a constant (127) velocity setting. You can select any one of them to match your performance or playing style.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 1 [PIANO 1/E.P. 1/ORGAN 1] button (the button will flash).

3 To select the curve, press C4 for (soft), C#4 (standard), D4 (hard),or D#4 (const).

C8C7C6C5C4C3C2C1

17

Owners Manual

4 Press the [BANK] button to exit the Setting mode.

Gentle Soft ( )

Strong

Loud ( ) Light

Heavy

Normal

Key Force

Output Level

Note Touch, control change setting

C4 Light (less force is required to play loudly)

C#4 Standard(general piano intensity)

D4 Heavy (gently struck notes are played softer)

D#4 CONST(all notes play with a velocity of 127)

Velocity Curve setting is used by controller and sound generator.

Transpose By transposing the keyboard, you can play a song in a different musical key without changing your fingering. Transpose is set in semitone, ranges within 1 octave(-12...12).

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 2 [PIANO 2/E.P. 2/ORGAN 2] button (the button will flash). Press one of the notes between C3...C5 to select the transpose setting.

C8C7C6C5C4C3C2C1

-12 +120

3 Press note C4 to cancel the transpose function.

4 Press the [BANK] button to exit the Setting mode.

Transpose setting is used by controller and sound generator.

Pitch The overall pitch, or tuning, of the K61Ps internal sound engine can be adjusted to match other instruments or recordings.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 3 [PIANO 3/E.P. 3 ORGAN 3] button (the button will flash).

3 Press note C4 to increase the pitch; every time C4 is pressed, the pitch increases about 0.5Hz Press note B3 to decrease the pitch; every time B3 is pressed, the pitch decreases about 0.5Hz

C8C7C6C5C4C3C2C1

Press note B3 and C4 together to restore standard pitch A4=440Hz.

18

4 Press the [BANK] button to exit the Setting mode.

The pitch setting reverts to standard A4=440Hz if the power is cut off

Temperament Temperaments are different tuning systems, mainly used in the baroque and classical periods. In addition to the standard equal tuning, the K61P provides historical Kirnberger and Werckmeister temperaments.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 4 [PIANO 4/E.P. 4/ORGAN 4] button (the button will flash).

3 To select a temperament, press C4 for Kirnberger, C#4 for Weckmeister, or D4 for Equal tuning.

C8C7C6C5C4C3C2C1

4 Press the [BANK] button to exit the Setting mode.

Note

C4

C#4

D4

Temperament

Werckmeister: Uses the Werckmeister scale proposed in the late Baroque period by organist and musicologist Andreas Werckmeister, with the intention of enabling relatively unrestricted play in multiple keys.

Kirnberger: Uses the Kirnberger scale proposed in the Johann Philip Kirnberger in the early 18th century. This temperament is mainly used for tuning harpsichords.

Equal temperament: The temperament used on almost all modern keyboard instruments. This temperament uses equal semitone increments, so that scales sound identical in all keys.

The termperament setting is set to equal temperament if power cut off.

A Note About Stretch Tuning Stretch tuning is used to obtain a more natural sound. Low diapason notes use a lower pitch setting, and high diapason notes use a higher pitch setting. This is the most often used method when tuning an acoustic piano. There are 6 instrument sounds in the K61P that use stretch tuning:

[PROGRAM] keys BANK 1

[PIANO1] Grand Piano 1

[PIANO2] Grand Piano 2

[PIANO3] Standard Piano

[PIANO4] Bright Piano

[PIANO5] Honky Tonk Piano

[PIANO6] Mellow Piano

19

Owners Manual

MIDI channel setting You can set the K61P to the same MIDI channel as the connected MIDI equipment. MIDI channel is 1-16.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 5 [PIANO 5/E.P. 5/ORGAN 5] button (the button will flash).

3 Press one of the notes between C4~D#5. The MIDI channel assignments are as the followings. C4 = 1ch, C#4=2ch, D4=3chD#5= 16ch

C8C7C6C5C4C3C2C1

4 Press the [BANK] button to exit the Setting mode.

MIDI channel setting is used by controller and sound generator.

The Local control on/off setting The Local setting separates the K61Ps keyboard from the internal sound engine. When local is on, the keyboard will play the internal sound engine, as well as any other connected devices. When using the K61P with a sequencer, you would normally set the local control to off, to prevent messages being sent to the computer from triggering notes a second time. This setting will depend on the echo back setting of the se- quencer. Generally, set local on, and the K61P will play sounds from the internal engine when notes are played on the keyboard.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 6 [PIANO 6/CLAVE/ORGAN 6] button (the button will flash).

3 Press note C4(On) or C#4(Off) to select the setting.

C8C7C6C5C4C3C2C1

4 Press the [BANK] button to exit the Setting mode.

20

The local control setting

Keyboard/Each controllers

Computer K61P

KBD/KNOB

SOUND/CTRL Tone generator

Local control on

Computer

KBD/KNOB

SOUND/CTRL

Local control off

Keyboard/Each controllers

K61P

Tone generator

The local on/off setting is set to local on if power cut off.

Program change enable/disable Every time you select one of the K61Ps internal sounds, a MIDI program change message is also sent to any connected MIDI equipment. This feature allows you to prevent program change messages from being sent to your other MIDI devices.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 7 [HARPSI 1/VIBE/STRINGS 1] button (the button will flash).

C8C7C6C5C4C3C2C1

3 Press note C4(enable) or C#4(disable) to select the setting.

4 Press the [BANK] button to exit the Setting mode.

21

Owners Manual

Volume message filter You can prevent the internal sound engine from receiving volume change messages. If the Volume message filter is set to On, the K61Ps internal sound generator will accept volume(07) message from Knob1, Knob2 and the Slider if they are assigned control change cc#07. If its set to Off, the K61Ps internal sound generator will reject volume(07) message from Knob1, Knob2 and the Slider even if they are assigned control change cc#07.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 8 [HARPSI 2/CHOIR/STRINGS 2] button (the button will flash).

C8C7C6C5C4C3C2C1

3 Press note C4(On) or C#4(Off) to select the setting.

CC#07 flow chart

ON OFF

SG

Controller

K61P

Controller

K61P

SG

Computer Computer

* SG: Sound Generator SG's volume knob controls SG's volume level.

4 Press [BANK] key to quit setting mode.

22

Troubleshooting Power does not turn on

Is the power switch set to the correct position? (p.8 Making connections and turning on the power)

Is the K-Series be connected to your computer via a hub? If so, try using the AC adapter.

Driver setup failure

There is a defalut driver installed for Windows. Use the new driver installer to setup driver.

Make sure the CD-ROM is inserted correctly into the CD drive.

Make sure the lens of CD drive is not dirty.

Software does not respond

Is the USB cable connected correctly?

Has the K-Series been recognized by the connected computer?

Depending on the hardware setup of your computer, it may not be possible for the K-Series to be recognized via a USB connection.

It may be that the connected device or software does not support the function youre attempting to use. Refer to the owners manual of the connected device or software, and make sure that the function is supported.

No sound(K61P)

Make sure the K-Series volume is not set to 0. Please turn the volume to an appropriate position.

Notes are dropping out or being cut off before playing to completion

You may be exceeding the K61Ps polyphony limit.

About Maximum Polyphony Maximum polyphony is the maximum number of notes that the internal sound engine is capable of producing at a single time. If you try to play more than this limit, the K61P automatically switches off older notes so that it can sound the newer notes. If you exceed the limit, therefore, you may notice that notes are dropping out or that they are ending prematurely. The maximum available polyphony varies according to the number of oscillators and effects used to produce the sound. The internal sound generator creates a note using either one or two oscillators. Maximum available polyphony for 1-oscil- lator sounds (such as the HARPSI/VIBES sounds) is 60 notes, while maximum polyphony for 2-oscillator sounds (such as Grand Piano 1 [PIANO 1, Bank A] and Grand Piano 2 [PIANO 2, Bank A]) is 30 notes. The reverb effect, when used, counts as ten 1-oscillator notes, while the chorus counts as three.

23

Owners Manual

Specifications Controllors

Keyboard: 25 keys / 49 keys / 61 keys; Full-size, velocity-sensing keys ClickPoint controller Assignable Knob 2 Assignable Switch 2 Octave shift up / down keys Pitch bend wheel Assignable Modulation wheel Slider 1

Internal sound generator(K61P) Sound generator Stereo sampling Polyphony 60 (Maximum) Sounds 24 (3 banks of 8) Keyboard pitch Transposition, Fine tuning Temperaments Equal, Kirnberger, Werckmeister Effects Reverb, Chorus (3 depths each)

Connectors Pedal jack MIDI OUT connector USB connector Power supply jack (DC9V) Outoputs (L/MONO, R) (K61P only) Headphones jack (K61P only)

Power supply USB BUS power mode (when using the USB connector) DC9V, AC adapter (optional)

Current consumption K25/K49/K61: When using USB bus power 110 mA

When using DC9V adapter 120 mA K61P: When using USB bus power 300 mA

When using DC9V adapter 320 mA

Dimensions (W H D) K25: 489 211 69 mm / 19.3 8.3 2.7 inches K49: 818 211 69 mm / 32.2 8.3 2.7 inches K61/K61P: 982 211 69 mm / 38.7 8.3 2.7 inches

Weight K25: 1.5 kg / 3.3 lbs. K49: 2.4 kg / 5.3 lbs. K61: 2.9 kg / 6.4 lbs. K61P: 3.1 kg / 6.8 lbs.

24

Included items USB cable CD-ROM (containing M1 Le software synthsizer, K-Series Editor software, Driver,

Setup Wizard etc.) Owners manual MIDI Implementation chart Software license agreement

Computer operating requirements Macintosh

Operating system: Mac OS X ver.10.3 or later Computer: Apple Macintosh computer with a USB port, satisfying the operating

requirements of Mac OS X Windows

Operating system: Microsoft Windows XP Home Edition/Professional Computer: Computer with a USB port, satisfying the operating requirements of

Windows XP (USB chipset made by Intel Corporation is recommended)

Options AC adapter Pedal switch PS-1

Appearance and specifications of the product are subject to change without notice. (Current as

of December 2005)

Sommaire

Prcautions.......................................................................... 26 Introduction ......................................................................... 27

Fonctions Principales .............................................................................27 Nom des parties .....................................................................................27

Installation ........................................................................... 30 Installation des drivers MIDI et des logiciels ..........................................30 Connexions et mise sous tension ...........................................................31 A propos de la srie K et des drivers de ports. .......................................33 A propos de la connection MIDI OUT de la srie K ................................33 Restoration des programmes dusine .....................................................34

Manuel doprations ........................................................... 35 Clavier ....................................................................................................35 ClickPoint ................................................................................................35 POTENTIOMTRE1 / POTENTIOMTRE2 ...........................................35 Boutons [SW1]/[SW2] .............................................................................36 Bouton [Octave superieur]/[OCTAVE inferieur] .......................................36 Molette de PITCH ...................................................................................36 Molette de MODULATION ......................................................................37 CURSEUR ..............................................................................................37 PEDALE .................................................................................................37

Jouer avec le gnrateur de sons (K61P) ......................... 38 Selectionner un son (Program change) ..................................................38 Effets ......................................................................................................38 mode de paramtrage ............................................................................39 Program change activ/dsactiv ..........................................................43

Messages derreur .............................................................. 45 Caractristiques .................................................................. 46

26

Prcautions Location Lutilisation de cet instrument dans les endroits suivants peut en entraner le mauvais fonctionnement. En plein soleil Endroits trs chauds ou trs humides Endroits sales ou fort poussireux Endroits soumis de fortes vibrations A proximit de champs magntiques

Alimentation Veuillez brancher ladaptateur secteur spcifi sur une prise secteur la tension approprie. Ne branchez pas ladaptateur sur une prise de cou- rant dont la tension ne correspond pas celle pour laquelle lappareil a t conu.

Interfrences avec dautres appareils lectriques Les postes de radio et de tlvision situs proximit peuvent souffrir dinterfrences la rception. Faites fonctionner cet appareil une distance raisonnable des postes de radio et de tlvision.

Maniement Pour viter de les endommager, manipulez les commandes et les boutons de cet instrument sans appliquer de force excessive.

Entretien Lorsque lextrieur est sale, essuyez-le avec un chiffon propre et sec. Ne vous servez pas dagents de nettoyage liquides comme du benzne ou du diluant, des produits de nettoyage ou des vernis inflammables.

Conservez ce manuel Aprs avoir lu ce manuel, veuillez le conserver soigneusement pour rfrence ultrieure.

vitez toute intrusion dobjets ou de liquide Ne placez jamais de rcipient contenant du liquide prs de linstrument. Si le liquide pntre dans lappareil, il risque de provoquer des dommages, un incendie ou une lectrocution. Veillez ne pas laisser tomber dobjets mtalliques dans le botier. Si cela se produisait, dbranchez ladaptateur secteur de la prise de courant et contactez votre revendeur Korg le plus proche ou le magasin o vous avez achet linstrument.

Marque CE pour les normes europennes harmonises La marque CE appose sur tous les produits de notre firme fonctionnant sur secteur jusquau 31 dcembre 1996 signifie que ces appareils rpondent la Directive EMC (89/336/CEE) et la Directive concernant la marque CE (93/68/ CEE). La marque CE appose aprs le 1 janvier 1997 signifie que ces appareils sont conformes la Directive EMC (89/336/CEE), la Directive concernant la marque CE (93/68/CEE) ainsi qu la Directive Basse Tension (73/23/CEE). La marque CE appose sur tous les produits de notre firme fonctionnant sur piles signifie que ces appareils rpondent la Directive EMC (89/336/ CEE) et la Directive concernant la marque CE (93/68/CEE).

REMARQUE IMPORTANTE POUR LES CLIENTS Ce produit a t fabriqu suivant des spcifications svres et des besoins en tension applicables dans le pays o ce produit doit tre utilis. Si vous avez achet ce produit sur internet, par correspondance ou/et au tlphone, vous devez vrifier que ce produit est bien utilisable dans votre pays de rsidence. ATTENTION: Lutilisation de ce produit dans un pays autre que celui pour lequel il a t conu peut tre dangereuse et annulera la garantie du fabricant ou du distributeur. Veuillez aussi conserver votre rcpiss qui est la preuve de votre achat, faute de quoi votre produit risque de ne plus tre couvert par la garantie du fabricant ou du distributeur.

* Les noms de societes, nomsm de produits et noms de formats, etc. dans ce manuel sont des marques de fabrique ou des mar-ques deposees de leurs proprietaires respectifs.

27

Manuel dutilisation

Introduction

Nous vous remercions pour votre achat dun contrleur K25/K49/K61/K61P(produit disponible ultrieurement). Afin demployer ce produit efficacement, lisez svp ce manuel soigneusement et employez le produit dune manire approprie. Maintenez ce manuel dans un endroit sr.

Fonctions Principales Equipp de 9 contrleurs puissants.

Track point X/Y avec pitchbend et mode ClickPoint. curseur/souris

Utilisez le logiciel de synthse fourni M1 Le avec le clavier de la srie K, vous pourrez entendre des sons de trs haute qualit immdiatement.

Les 24 sons du K61Ps sont issus des pianos numriques Korg. Vous pouvez jouer des sons de pianos et dorgue de trs haute qualit.

Nom des parties Contrleur

1

2

3 4 5

6 7 8 K61P

28

1. Clavier Le clavier possde des touchesstandard sensibles la vlocit.

2. ClickPoint Assign en MIDI, le ClickPoint peut tre utilis pour contrler des appareils externes branchs en MIDI, et des logiciels de synthses comme des squenceurs tournant sur PC. Le ClickPoint peut tre utilis aussi comme une souris.

3. POTENTIOMETRE 1 / POTENTIOMETRE 2 Assign en MIDI, les potentiomtres 1 & 2 peuvent tre utiliss pour contrler des appareils externes branchs en MIDI, et des logiciels de synthses comme des squenceurs tournant sur PC.

4. Boutons [SW1] / [SW2] Les boutons [SW1]/[SW2] sont utiliss pour les changements de programme. Avec les assignations de contrle MIDI, ils peuvent tre utiliss pour contrler des appareils externes branchs en MIDI, et des logiciels de synthses comme des squenceurs tournant sur PC.

5. Boutons [OCTAVE SUPERIEUR] / [OCTAVE INFERIEUR] Rglez lchelle doctave du clavier.

6. Molette de PITCH Change le pitch vers le haut ou vers le bas.

7. Molette de MODULATION Assign en MIDI, la molette de modulation peut tre utilis pour contrler des appareils externes branchs en MIDI, et des logiciels de synthses comme des squenceurs tournant sur PC. Le ClickPoint peut tre utilis aussi comme une souris.

8. CURSEUR Assign en MIDI, le curseur peut tre utilis pour contrler des appareils externes branchs en MIDI, et des logiciels de synthses comme des squenceurs tournant sur PC. Le ClickPoint peut tre utilis aussi comme une souris.

Gnrateur sonore (K61P)

1 2 3 4 5

1. Potentiomtre [VOLUME] Contrle le volume du gnrateur sonore interne. Ceci ajuste le volume qui est rout ves les sorties OUTPUT et la sortie casque.

29

Manuel dutilisation

2. Bouton [BANK] 3 sons sont assigns chaque bouton programme. Pressez (BANK) pourslectionner lun dentre eux.

3. Bouton [PROGRAM] Selectioonne les sons assigns aux boutons.

4. Bouton [REVERB] Ce bouton rgl pour enclencher ou teidre leffet echo, et la profondeur de la rverbration.

5. Bouton [CHORUS] Ce bouton est rgl pour enclencher ou teidre lpartiel, et la profondeur de leffet chorus.

Panneau Arrire

1 2 3 4 5 6 7

Illustration shows the rear panel of K61P.

1. Jacks de sortie (seulement K61P) Permet la connection un amplificateur afin dcouter les sons internes.

2. Sortie casque (seulement K61P) Chaque jack peut tre connect un casque avec connection standard.

3. Jack pour PEDALE Une pdale action momentane telle que le commutateur pdale PS-1 (chacun vendu sparment) peut tre raccorde la prise de pdale. La Serie Kdterminera automatiquement la polarit de la pdale quand lappareil est aliment.

4. Connecteur MIDI OUT Connectez un appareil externe MIDI. La prise MIDI OUT fonctionne diffremment suivant les connections.

5. Connecteur USB Utilisez un cable USB pour connecter la srie K votre ordinateur afin que les messages MIDI soient transmis et reus.

6. Bouton dalimentation Ce switch permet de mettre la serie K sous tension en utilisant ladaptateur secteur ou le cable USB.

7. Connecteur dalimentation Connectez ladaptateur secteur optionnel ici.

30

Installation

Installation des drivers MIDI et des logiciels Contenu du CD-ROM Editeur de la srie K Logiciel de synthse KORG M1 Le KORG USB-MIDI driver pour Windows XP Guide dinstallation Mode demploi de la srie K Manuel dutilisation du logiciel de synthse M1 Le software Licence de logiciel

Recommandation de systmes Pour Mac OS X Ordinateur

Apple Macintosh avec port USB cela satisfait les exigences dexploitation de Mac OS X

Systme dexploitation recommand Mac OS X ver.10.3 ou suprieur

Pour Windows XP

Ordinateur Un ordinateur avec un port USB cel satisfait les exigences dexploitation de Microsoft Windows XP (le chipset USB fabriqu par Intel Corporation est recommand)

Systme dexploitation recommand Microsoft Windows XP Home Edition/Professional Service pack 1 ou superieur

Installation Sil vous plait, lisez les instructions dinstallation situes sur le CD-ROM fourni pour linstallation du driver MIDI-USB pour windows XP, le logiciel ddition de la srie K et le logiciel de synthse M1 Le.

Lire avant utilisation sil vous plait Le copyright de tout le logiciel concernant ce produit est la proprit de Korg Cor-

poration. Laccord de licence pour le logiciel concernant ce produit est inclus sparment.

Vous devez lire cet accord de licence avant que vous installiez le logiciel. Votre installation du logiciel sera prise pour indiquer votre acceptation de laccord.

Apple, Macintosh et mac os sont les marques dposes enregistres de lordinateur Apple, inc..

Windows XP est une marque dpose enregistre de Microsoft Corporation aux ETATS-UNIS et dautres pays.

Tous autres nom de produit et de compagnie sont des marques dposes ou des marques dposes enregistres de leurs supports respectifs.

31

Manuel dutilisation

Connexions et mise sous tension Vrifiez que tous vos quipements soient teints avant de commentcer quoique ce soit. Vous devez faire attention lors de lcoute, sinon vous pouvez endommager votre systme de haut-parleur ou causer dautres dfauts de fonctionnement.

Connexion USB 1 Employez un cble USB pour relier la K-Srie au connecteur USB de votre

ordinateur. Si vous voulez employer une pdale, reliez la la prise PDALE.

2 Pour tablir le courant, placez le commutateur de puissance des K-Sri dans la position USB.

La K-Srie dtecte la polarit de la pdale quand le courant est tabli. Si une pdale est relie, ne la maintenez pas tant que vous navez pas allum le clavier de la srie K.

Pedal switch

PEDAL jack

Power switch position

USB cable

Computer

USB connector

3 Quand vous tes prt couper le courant, placez le commutateur de puissance sur STANDBY.

Si vous employez un raccordement Usb, vous navez pas besoin dutiliser un adapteur secteur.Cependant si votre ordinateur est sous aliment, ou si vous employez un hub USB qui est aliment uniquement par le por t (plutt quautoaliment), la puissance ne peut tre assure la srie K. Dans ce cas-ci, utilisez ladapteur secteur optionnel et placez le commutateur de puissance sur la position DC.

Quand lUSB est connecte, la borne MIDI out ne transmettra aucun message au clavier de contrle.

Connexions MIDI et de Iadaptateur CA 1 Reliez la prise dadapteursecteur optionnel au connecteur de lalimentation des

sries K et branchez ladapteur une sortie lectrique.

2 Employez un cble MIDI pour relier la Srie K votre module externe MIDI. Si vous voulez employer une pdale facultative, reliez la prise de pdale.

32

3 Commutez lalimentation, la LED sallumera. ce moment, les rglages sauvs seront lus automatiquement.

4 Allumez vos appareils externes.

La K-Srie dtecte la polarit de la pdale quand le courant est tabli. Si une pdale est relie, ne la maintenez pas tant que vous navez pas allum la srie K.

MIDI IN

MIDI OUT

Pedal switch

MIDI cable

External MIDI sound module

PEDAL jack

Power switch position

Plug the AC adaptor into an AC outlet

Power supply connector

5 Quand vous tes prt couper le courant, teignez les appareils sonores externes connects en MIDI. Puis rglez le switch dalimentation de la srie K sur STANDBY.

Gnrateur de sons interne 1 Reliez la prise dadapteur secteur optionnel. au connecteur dalimentation de la

srie K, et branchez ladapteur une prise de courant.

2 Reliez chaque cble la prise dentre correspondante sur lappareil externe. Employez des cbles mono 6, 35mm. Quand vous connectez seulement un produit, employez la prise L/mono.

Utilisez le bouton de volume pour ajuster le niveau de sortie des sorties OUTPUT.

3 Positionnez le selecteur sur DC. La led dalimentationsallume.

4 Allumez votre systme damplification.

Headphone

Amplified speakers HEADPHONES jackOUTPUT jack

INPUT

33

Manuel dutilisation

A propos de la srie K et des drivers de ports. La srie K dispose de 1 port USB-MIDI In et 2 ports USB-MIDI OUT.

Keyboard/Slider/ Pitch,Mod wheel/ SW1/SW2/Pedal/ ClickPoint/ Dump data

The driver of the application on a computer K-series

MIDI OUT device

MIDI IN device

MIDI OUT

KBD/KNOB

SOUND/CTRL *1

MIDI OUT juck

Dump data Sound generator *2

*1 K25/49/61 is CTRL *2 K61P only

MIDI IN KBD / KNOB KBD/KNOB est utilis pour recevoir des messages MIDI de la srie K et des contrleurs. Quand vous utilisez votre application informatique partir de la srie K, slectionnez ce port pour les entres MIDI de votre application. KBD/KNOB est utilis aussi pour recevoir des donnes de scne. Slectionnez ce port pour lentre MIDI de lditeur de la srie K.

MIDI OUT MIDI OUT MIDI OUT transmet des messages MIDI OUT du logiciel la srie K. par exemple la transmission de messages MIDI de lordinateur aux instruments MIDI. Quand la srie K est utilise comme un port USB-MIDI, selectionnez ce port pour les pour les port MIDI OUT de vos applications.

SOUND / CTRL (CTRL si K25/K49/K61) SOUND/CTRL est utilis pour recevoir des donnes de scne venant de lordinateur. Slectionnez ce port pour les entres MIDI de la srie K. De plus, ce port permet au K 61P de jouer des notes du gnrateur de son interne.

A propos de la connection MIDI OUT de la srie K Quand lUSB nest pas connect Envoi des messages MIDI venant du clavier et du contrleur.

Quand lUSB est connect Envoi des messages MIDI venant du MIDI OUT de lordinateur. Il nenvoi pas de mes- sages MIDI venant du clavier et du contrleur.

34

Restoration des programmes dusine Allumez le clavier en maintenant les touchesSW1 et SW2.

Rglages des contrleurs quand lappareil est dball

Contrleurss Fonction

SW1 / SW2 Changement de programme (-1/+1)

KNOB1 CC#074 (Cutoff)

KNOB2 CC#079 (EG Intensity)

SLIDER CC#007 (Volume)

PITCH wheel Fixed (Pitch Bend)

MOD wheel CC#001 (Modulation)

PEDAL CC#064 (Damper)

ClickPoint Mode voice

* Les paramtres montrs l'intrieur des parenthses concernent le M1 Le.

35

Manuel dutilisation

Manuel doprations Utilisez lditeur de la srie K pour paramtrer celui ci.

Les messages MIDI sont envoys en utilisant le canal MIDI global.

Clavier Envoi des messages de notes. 3 courbes de vlocit et une constante (127) peuvent tre paramtres afin davoir la raction adquate. La touche de transposition peut tre rgl par 1/2 ton jusqu 1 octave(-12...12).

ClickPoint Le changement de contrle MIDI peut tre assign individuellement la direction X (gauche /droit) et la direction Y (haut/bas) pour obtenir deux paramtres. En outre, ClickPoint peut tre employ comme souris dordinateur. Les valeurs assignables sont pas dassignation/ changement de contrle /souris.

Pas dassignation Si le ClickPoint nest pas assign au contrle MIDI, les messagesseront non transmis.

Changement de contrle [0...127] Le contrle MIDI a t assign. Changez le paramtre de direction X et Y en changeant la position. ClickPoint sera de nouveau la position centrale quand il est relach, les paramtres x et y peuvent rester la position quand le bouton de clic est enclench. Appuyez sur le buton de clic encore pour ouvrir les paramtres de x et de y.

Souris Sil est assign au mode souris, le ClickPoint peut tre actionn comme souris et commander lindicateur de souris sur lcran de lordinateur. Le bouton de clic devient le bouton de clic en mode souris.

Quand le MIDI OUT est reli, ClickPoint ne peut pas tre employ comme souris mme si il est assign en mode souris.

POTENTIOMTRE1 / POTENTIOMTRE2 Avec lassignation de contrle MIDI, knob1/knob2 peut tre employ pour piloter lquipement MIDI externe ou le logiciel de synthse fonctionnant sur ordinateur. Les valeurs assignables sont aucun changement dAssignation/Changement de Control.

Pas dassignation Si knob1/knob2 nont aucune assignation de commande MIDI, les messages MIDI ne seront pas envoys.

Changement de contrle [0...127] KNOB1/KNOB2 sont utiliss pour changer les paramtres des contrles MIDI.

36

Boutons [SW1]/[SW2] Appuyes sur [SW1]/[SW2] pour envoyer des messages dassignation de commande MIDI. Les valeurs assignables sur SW1 et SW2 sont pas dassignation/changement du programme/Changement de contrle.

Pas dassignation Si le SW1/SW2 nest pas assign au contrle MIDI, les messagesseront non transmis.

Changement de programme Quand [SW1] est slectionn,le changement de programme dcroit de 1. Quand [SW] est slectionn,le changement de programme augmente de 1. De plus, Le changement de programme est rgl 0 si [SW1]/[SW2] sont slectionns ensemble.

Changement de contrle [0...127] [SW1]/[SW2] sont assigns aux contrles MIDI avec une slection de mode Toggle/ Momentary, et valeur de ouvertures et de fermetures. En mode Toggle appuyez chaque fois [SW1]/[SW2] les touches, message de commande du MIDI avec le paramtre OnValue et Off Value sera envoy. En mode Momentary appuyez chaque fois les touches [SW1]/[SW2], le message de contrle MIDI avec le paramtre OnValue sera envoy quand il est appuy et le message de commande du MIDI avec le paramtre OffValue sera envoy quand il sera seletionn vers le haut.

Bouton [Octave superieur]/[OCTAVE inferieur] Rglez le slecteur doctave. Lchelle doctave du clavier a plusieurs paramtres.

K-Series Octaves

K25 -4...+4

K49 -4...+4

K61/K61P -3...+3

Key leds (tat) rglage dOctave

Sombre 0 octave

Vert +1 / -1octave

Orange +2 / -2octave

Rouge +3 / -3octave

Red clignotant +4 / -4octave(K25/K49 seulement)

Molette de PITCH Utilisez Le la molette vers le haut/bas pour envoyer des messages MIDI de changement de pitch.

37

Manuel dutilisation

Molette de MODULATION Avec lassignation du contrle MIDI, la molette de modulation peut tre utilise pour piloter lquipement MIDI externe ou le synthtiseur logiciel fonctionnant sur lordinateur. Les valeurs assignables sont pas dassignation/Changement de contrle/aftertouch.

Pas dassignation Si la molette de modulation nest pas assign au contrle MIDI, les messages seront non transmis.

Changement de contrle [0...127] Utilisez la molette de modulation pour changer le paramtre du contrle MIDI assign.

After Touch Utilisez la molette de modulation pour envoyer un message dAfterTouch au canal.

CURSEUR Avec lassignation du contrle MIDI, le curseur peut tre utilis pour piloter lquipement MIDI externe et le synthtiseurlogiciel tournant sur lordinateur. Les valeurs assignables sont Pas dassignation/Changement de Control.

Pas dassignation si le curseur na pas dassignation de contrle MIDI, aucun message transmis.

Changement de contrle [0...127] Utilisez le curseur pour changer le paramtre assign au changement de contrle MIDI.

PEDALE Le changement de contrle MIDI peut tre assign la prise pdale reli et une pdale de sustain. Les valeurs assignables sont Pas dassignation/Changement de Control.

Pas dassignation Si la pdale na pas dassignation de contrle MIDI, pas de messages transmis.

Changement de contrle [0...127] La pdale est assigne aux commandes MIDI avec le choix entre le mode Toggle/ Momentary, et les les valeurs OnValue et OffValue. En mode Toggle chaque fois que vous appuyez sur la pdale, le message de commande MIDI avec le paramtre OnValue et OffValue sera envoy. En mode Mo- mentary chaque fois que vous appuyez sur la pdale, le message de commande MIDI avec le paramtre OnValue sera envoy quand appuyez et message de commande MIDI avec le paramtre OffValue sera envoy quand vous relacherez la pdale.

38

Jouer avec le gnrateur de sons (K61P)

Selectionner un son (Program change) 1 Slectionnez le son dsir en utilisant les boutons de slection.

2 Appuyez sur le bouton de banque jusqu ce que vous choisissiez une des trois. Chaque fois que le boutonf de banque enfonc, la banque choisie commutera de BANK1, de BANK2 ou de BANK3. La banque choisie sera montre par les leds. Par exemple, pour choisir le son de Clavi, appuyez sur la sixime touche de programme de la gauchepour allumer la led principale. Appuyez alors sur la tou- che de banque pour choisir BANK2.

[PROGRAM] key

[PIANO 1]

[PIANO 2]

[PIANO 3]

[PIANO 4]

[PIANO 5]

[PIANO 6]

[HARPSI 1]

[HARPSI 2]

Bank2

E. Piano 1

E. Piano 2

Soft E.P.

Vintage E.P.

E.P. Pad

Clavi

Vibraphone

Choir

Bank3

Jazz Organ 1

Jazz Organ 2

Jazz Organ 3

Church Organ 1

Church Organ 2

Church Organ 3

Strings

Slow Strings

Osc#

2

2

1

1

2

1

1

2

Osc#

1

1

1

1

2

1

1

1

Osc#

2

2

2

3

1

1

1

2

Bank1

Grand Piano 1

Grand Piano 2

Standard Piano

Bright Piano

Honky Tonk Piano

Mellow Piano

Harpsichord 1

Harpsichord 2

Sound List

* [PROGRAM] key is BANK1s label. * Indicates the number of oscillators used to produce the voice.

Effets Reverbration Ajoutez leffet dcho avec la profondeur spcifique un bruit peut simuler des effets soniques comme jouer sur la scne dune salle de concert. Ceci sappelle leffet de reverbration.

1 Appuyez sur le bouton [REVERB] pour slectionner une des trois profondeurs de rverbration. Les rglages seront indiqus par des Leds.

[Led REVERB] profondeur de Reverb

Eteint teint

Vert Lgre

Orange Standard

Rouge Profond

39

Manuel dutilisation

Chorus Ajoutez des sons dcals pour avoir un effet riche et profond. Ce sappelle leffet de chorus.

1 Appuyez sur la touche [CHORUS], choisissez une des trois profondeurs de cho- rus. Le paramtrage choisi est montr par la led principale.

Bouton [CHORUS] profondeur de Reverb

Eteint teint

Vert Lger

Orange Standard

Rouge profond

mode de paramtrage Appuyez sur le bouton [BANK] jusqu ce quelle place la srie K en mode rglage. Les leds des 8 boutons de programme et la touche [BANK]steignent. Pressez un des 8 boutons de programme pour choisir le rglage que vous voulez. La led du bouton de programme choisi clignotera. Appuez alors sur la note du clavier pour placer la valeur choisie. Aprs avoir fini le rglage, appuyez sur la touche [BANK] pour quitter le mode. En mode rglage, il y a 8 paramtres de rglage comme suit:

[PROGRAM] keys

[PIANO 1]

[PIANO 2]

[PIANO 3]

[PIANO 4]

[PIANO 5]

[PIANO 6]

[HARPSI 1]

[HARPSI 2]

Contents

Velocity Curve Setting

Transposing the Keyboard

Adjusting the Pitch

Selecting a Temperament

Changing the Global MIDI Channel Setting

The Local Control On/Off Setting

Enabling or Disabling Program Changes

Enabling or Disabling Volume Message Filter

Function

Velocity curve

Transpose

Pitch

Temperament

Global MIDI channel

Local control

Program Change Setting

Volume message filter

* [PROGRAM] key is BANK 1s lablel.

Courbe de vlocit Il y a 3 courbes de vlocit et 1 constante (127) Choisissez une delles selon votre besoin.

1 Appuyez sur le bouton [BANK] jusqu ce que le clavier se mette en mode paramtrage.

2 Pressez le Programme 1 [PIANO 1/E.P. 1/ORGAN 1] pour allumer la Led.

3 Presez une de ces notes C4(lger), C#4(standard), D4(dur), D#4(const) pour slectionner la courbe.

C8C7C6C5C4C3C2C1

40

4 Pressez [BANK] pour quitter le mode de paramtrage.

Gentle Soft ( )

Strong

Loud ( ) Light

Heavy

Normal

Key Force

Output Level

Note Touch, control change setting

C4 Son doux avec courbe dure mme joue doucement)

C#4 Intensit de piano Standard (general)

D4 Son fort avec courbe douce si jou doucement

D#4 CONST(son avec intensit fixe (velocity=127))

Le paramtrage de le courbe de vlocit est utilise par

le contrleur et le gnrateur de sons.

Transposition En utilisant le transpose vous pouvez jouer la chanson avec s moins de touches noires, aussi bien que jouer des chansons avec des positions familires de doigt. Le trans- pose est rgl par demi ton, 1 octave (-12... 12).

1 Appuyez sur [BANK] jusqu ce que le clavier soit en mode rglage.

2 Pressez Program 2 [PIANO 2/E.P. 2/ORGAN 2] pour allumer la led Pressez une des notes entre C3...C5 pour selectionner les rglages.

C8C7C6C5C4C3C2C1

-12 +120

3 Appuyez sur la note C4 pour annuler la transposition.

4 Pressez le bouton [BANK] pour quitter le mode de paramtres.

Les rglages de transposition sont utiliss par le contrleur et le gnrateur sonore.

Pitch 1 Appuyez sur [BANK] jusqu ce que le clavier soit en mode rglage.

2 Pressez Program 3 [PIANO 3/E.P. 3 ORGAN 3]pour allumer la led.

3 Pressez la note C4 pour augmenter le pitch, chaque fois que la note C4 est prsse le pitchaugmente denviron 0.5Hz. Pressez la note B3 pour dscendre le pitch, chaque fois que la note B3 est enfonce, le pitch diminue denviron 0.5Hz.

C8C7C6C5C4C3C2C1

Pressez les notes B3 etC 4ensembles pour revenir au pitch standard A4=440Hz.

4 Pressez [BANK] pour quitter le mode de rglage.

le rglage de pitch est rgl en standard sur A4=440Hzsi lappareil est teint.

41

Manuel dutilisation

Temprament Slectionne le temprament de la musique. Il y a quelques morceaux de musique classique qui emploient le temperament classique. Afin de jouer les notes avec ce temperament, la K-Srie possde ceux classique appels Kirnberger et Werckmeister, et le temperament gal le plus largement utilis par les instruments actuels.

1 Appuyez sur [BANK] jusqu ce que le clavier soit en mode rglage.

2 Pressez Program 4 [PIANO 4/E.P. 4/ORGAN 4] pour clairer les Led.

3 Pressez une des notes C4(Kirnberger), C#4(Weckmeister), D4(Euqal) pour slectionner le temperament.

C8C7C6C5C4C3C2C1

4 Pressez [BANK] pour quitter le mode de rglage.

Note

C4

C#4

D4

Temperament

Werckmeister: Uses the Werckmeister scale proposed in the late Baroque period by organist and musicologist Andreas Werckmeister, with the intention of enabling relatively unrestricted play in multiple keys.

Kirnberger: Uses the Kirnberger scale proposed in the Johann Philip Kirnberger in the early 18th century. This temperament is mainly used for tuning harpsichords.

Equal temperament: The temperament used on almost all modern keyboard instruments. This temperament uses equal semitone increments, so that scales sound identical in all keys.

Le temprament par dfaut lexctinction est le rglage qual.

Note propos du Stretch Tuning Le Stretch tuning est employ pour obtenir un bruit plus naturel. Les notes basses du diapason utilisent des rglages de pitch plus bas, et les notes leves de diapason utilisent un rglages de pitch plus haut. Cest la mthode daccord le plus souvent utilise dans le piano. Il y a 6 instruments dans le gnrateur de sons de la srie K en utilisant le stretch tuning, comme suit.

[PROGRAM] BANK 1

[PIANO1] Grand Piano 1

[PIANO2] Grand Piano 2

[PIANO3] Standard Piano

[PIANO4] Bright Piano

[PIANO5] Honky Tonk Piano

[PIANO6] Mellow Piano

42

Rglage du canal MIDI Rgler le canal MIDI de votre clavier sur le mme canal que votre quipement MIDI externe. Canaux MIDI 1 16.

1 Appuyez sur [BANK] jusqu ce que le clavier soit en mode rglage.

2 Pressez Program 5 [PIANO 5/E.P. 5/ORGAN 5] pour clairer la Led.

3 Pressez une des notes entre C4~D#5. Le rglage du canal MIDI est le suivant. C4=1ch, C#4=2ch, D4=3chD#5=16ch

C8C7C6C5C4C3C2C1

4 Pressez [BANK] pour quitter le mode rglage.

Le rglage du canal MIDI est utilis par le contrleur et le gnrateur sonore.

Rglage du contrle Local on/off Slectionner le mode Local Off pour dsactiver le gnrateur de son interne de la srie K. Le son du gnrateur sonore externe sera audible. Sil est reli au squenceur avec rglage dcho back, rglez la srie KS sur local off pour empcher le renvoi de message de notes et causer des double notes. Dune faon gnrale, placez local on, quand vous jouez les sons de la srie K.

1 Appuyez sur [BANK] jusqu ce que le clavier soit en mode rglage.

2 Pressez Program 6 [PIANO 6/CLAVE/ORGAN 6] pour allumer la led

3 Pressez la note C4(On) ouC#4(Off) pour slectionner les rglages.

C8C7C6C5C4C3C2C1

4 Pressez [BANK] pour quitter le mode rglage.

43

Manuel dutilisation

Les rglages du contrle local

Keyboard/Each controllers

Computer K61P

KBD/KNOB

SOUND/CTRL Tone generator

Local control on

Computer

KBD/KNOB

SOUND/CTRL

Local control off

Keyboard/Each controllers

K61P

Tone generator

Le rglage du local on/off est sur local on quand lappareil est teint.

Program change activ/dsactiv Cancel program change if you dont want program change message sent to connected equipment, otherwise you can enable it.

1 Appuyez sur [BANK] jusqu ce que le clavier soit en mode rglage.

2 Pressez Program 7 [HARPSI 1/VIBE/STRINGS 1] pour allumer la Led.

C8C7C6C5C4C3C2C1

3 Pressez la note C4(activ or C#4(dsactiv) pour slectionner le rglage.

4 Pressez [BANK] pour quitter le mode paramtres.

44

Message de filtre de volume lLe message de chnagementd e contrle MIDI cc#07(volume) du gnrateur de son interne peut tre ffac. Si il est rgl sur On, le gnrateur sonore de la srieK acceptera le message de volume (07) des potentiomtres1/potentiomtres 2 and curseur si ils sont assigns au changement de contrle cc#07. Si il est rgl sur Off, le gnrateur sonore de la srie K refusera le message de volume (07) des potentiomtres1/potentiomtres 2 and curseur mme si ils sont assigns au changement de contrle cc#07.

1 Appuyez sur [BANK] jusqu ce que le clavier soit en mode rglage.

2 Pressez Program 8 [HARPSI 2/CHOIR/STRINGS 2] pour allumer la Led.

C8C7C6C5C4C3C2C1

3 Pressez la note C4(On) or C#4(Off)pour slectionner les rglages.

CC#07 tableau de flux

ON OFF

SG

Controller

K61P

Controller

K61P

SG

Computer Computer

* SG: Sound Generator SG's volume knob controls SG's volume level.

4 Pressez [BANK] pour quitter le mode de paramters.

45

Manuel dutilisation

Messages derreur Lappareil ne peut pas sallumer

Est ce que le bouton dalimentation est sur la bonne position? (p.31 Connexions et mise sous tension)

La srie K peut elle tre connecte votre ordinateur via un hub USB?

chec de rglage de votre driver

Il y a un driver install par dfaut pour Windows. utiliser le nouvel installateur pour paramtrer le driver.

Vrifiez que le CD-ROM est correctement insrr dans le lecteur.

Vrifiez que la lentille du lecteur de Cd nest pas sale. Utiliser un produit compatible et spcialis pour nettoyer la lentille.

Le logiciel ne rpond pas

Est ce que le cable USB est correctement install ?

Est ce que la srie K est reconnue par lordinateur connect?

Selon linstallation de matriel de votre ordinateur, il se peut que la srie K ne soit pas reconnue par lintermdiaire dune connection USB.

Il se peut que le dispositif ou le logiciel reli naccepte pas la fonction que vous essayez dutiliser. Rfrez-vous au manuel du propritaire de lappareil ou du logiciel reli, et assurez-vous que la fonction soit compatible.

Pas de sons(K61P)

Vrifiez que le volume du clavier ne soit pas sur 0. Tourner le potentiomtre jusqu la position approprie.

Les notes sont dcoupes ou touffes

Vous excedez la limite de polyphonie de lappareil

A propos de la polyphonie maximum La polyphonie maximum est le nombre maximum de notes que le piano est capable de reproduire en mme temps. Si vous essayez de jouer au del de cette limite, le piano coupe automatiquement des notes plus anciennes de sorte quil puisse jouer les notes plus rcentes. Si vous dpassez la limite, donc, vous pouvez noter que les sons sont dcoups ou touffs. La polyphonie disponible maximum change selon le nombre doscillateurs et deffets employs pour produire le son. Le piano produit chaque son en utilisant lun ou lautre des oscillateurs. La polyphonie disponible maximum pour des sons de 1 oscillateur (tels que les sons de HARPSI/vibes) est 60 notes, alors que la polyphonie maximum pour 2 oscillateurs (comme piano queue 1 [ PIANO 1, A ] et piano queue 2 [ le PIANO 2, encaissent A ]) est de 30 notes. Leffet de reverb, une fois utilis, compte en tant que dix notes 1-oscillator, alors que le chorus compte en tant que trois.

46

Caractristiques Contrleurs

Clavier: 25 notes / 49 notes, 61 notes toucher clavier standard avec vlocit. ClickPoint Potentiomtres Assignables 2 Boutons Assignables 2 Changement doctave superieur/inferieur Molette de Pitch bend Molette de Modulation Assignable Curseurr 1

Gnrateur de sons interne(K61P) Generateur sonore Echantillonnage Stereo Polyphonie 60 (Maximum) Sons 24 (3 banques def 8) Accord du clavier Transposition, Fine tuning Tempraments Equal, Kirnberger, Werckmeister Effets Reverb, Chorus (3 rglages de profondeur chacun)

Connecteurs Jack Pdale Connecteur MIDI OUT Port USB Prise pour adaptateur secteur (DC9V) Sorties (L/MONO, R) (K61P seulement) Prise casque (K61P seulement)

Alimentation Port USB en mode alimentation (en utilisant le connecteur USB Adaptateur secteur DC9V, AC (optionel)

Consommations de courant K25/K49/K61: En utilisant le port USB 110 mA

En utilisant ladaptateur secteur 120 mA K61P: En utilisant le port USB 300 mA

En utilisant ladaptateur secteur 320 mA

Dimensions (L P H) K25: 489 221 69 mm K49: 818 221 69 mm K61/K61P: 982 221 69 mm

Poids K25: 1.5 kg K49: 2.4 kg K61: 2.9 kg K61P: 3.1 kg

47

Manuel dutilisation

Articles inclus Cable USB CD-ROM (contenant le logiciel de synthse M1 Le, Logiciel ddition de la srie

K, Driver, Aide linstallation) Mode demploi Tableau dimplmentation MIDI Accord de licence de logiciel

Ressources ordinateur recommandes Macintosh

Systme dexploitation: Mac OS X ver.10.3 ou supperieur Ordinateur: Apple Macintosh avec un port USB satisfaisant au cahier des

charges de Mac OS X Windows

Systme dexploitation: Microsoft Windows XP Home Edition/Professional Computer: Ordinateur avec un por t USB , satisfaisant au systme

dexploitation Windows XP (USB chipset fabriqu par Intel Corporation recommend)

Options Adaptateur secteur Pdale switch PS-1

Lapparence et les caractristiques de ce produit sont sujettes modifications sans pravis.

Inhalt

Vorsichtsmaregeln ............................................................ 49 Einleitung ............................................................................. 50

Die wichtigsten Funktionen ....................................................................50 Bedienelemente und ihre Funktionen .....................................................50

Vorbereitung ........................................................................ 53 Installieren des MIDI-Treibers und der Software ....................................53 Anschlsse und Einschalten ..................................................................54 Die K-Serie und die Treiber-Ports ...........................................................56 Die MIDI OUT-Buchse der K-Serie .........................................................56 Wiederherstellen der Werksvorgaben ....................................................57

Bedienung............................................................................ 58 Tastatur (Keyboard) ................................................................................58 ClickPoint ................................................................................................58 KNOB1 und KNOB2 ...............................................................................58 SW1- & SW2-Taster ...............................................................................59 [OCTAVE SHIFT UP]- & [OCTAVE SHIFT DOWN]-Taster ......................59 PITCH-Rad .............................................................................................59 MOD-Rad ...............................................................................................60 SLIDER ..................................................................................................60 PEDAL ....................................................................................................60

Verwendung der Klangerzeugung (K61P) ........................ 61 Anwhlen von Klngen ...........................................................................61 Effekte ....................................................................................................61 Einstellungen ..........................................................................................62 Aktivieren/Filtern von Programmwechseln .............................................66

Fehlersuche ......................................................................... 68 Technische Daten ................................................................ 69

49

Bedienungsanleitung

Vorsichtsmaregeln Verwendungsort Bei Verwendung des Gerts an den folgenden Orten kann eine Fehlfunktion auftreten. Im direkten Sonnenlicht An Orten mit extremer Temperatur oder

Luftfeuchtigkeit An sehr staubigen oder schmutzigen Orten An Orten mit starker Vibration In der Nhe von Magnetfeldern

Stromversorgung Schlieen Sie das spezielle Netzteil an eine Netzsteckdose mit der richtigen Netzspannung an. Schlieen Sie es nicht an eine Steckdose mit einer anderen Spannung als der fr das Gert geeigneten an.

Strungen mit anderen elektrischen Gerten In der Nhe aufgestellte Radio- oder Fernsehgerte knnen Empfangsstrungen aufweisen. Betreiben Sie dieses Gert immer in einem geeigneten Abstand von Radio-oder Fernsehgerten.

Behandlung Um Beschdigungen zu vermeiden, bettigen Sie Schalter oder Bedienungselement nicht mit Gewalt.

Pflege Wenn das uere schmutzig wird, mit einem sauberen, trockenen Lappen abwischen. Verwenden Sie keine flchtigen organischen Lsungsmittel wird Benzol, Terpentin, Reinigungslsungen oder entflammbare Poliermittel.

Die Anleitung aufbewahren Nach dem Lesen dieser Anleitung bewahren Sie sie bitte zum Nachschlagen auf.

Fremdkrper aus dem Gert halten Stellen Sie niemals Behlter mit Flssigkeiten in der Nhe des Gerts ab. Wenn Flssigkeit in das Gert eindringt, kann ein Gerteausfall, Brand oder elektrischer Schlag verursacht werden. Achten Sie darauf, keine Metallobjekte in das Gert kommen zu lassen. Falls ein Gegenstand in das Gert eindringt, ziehen Sie das Netzteil von der Steckdose ab. Dann wenden Sie sich an Ihren Korg-Fachhndler oder an des Geschft, in dem das Gert gekauft wurde.

CE-Kennzeichen fr europische harmonisierte Standards Das CE-Kennzeichen, dass an den mit Netzstrom betriebenen Produkten unserer Firma, hergestellt bis zum 31. Dezember 1996, angebracht ist, zeigt an, dass das betreffende Gert mit der EMV- Richtlinie (89/336/EWG) und der CE- Kennzeichen-Richtlinie (93/68/EWG) bereinstimmt.

Das nach dem 1. Januar 1997 angebrachte CE- Kennzeichen weist auf bereinstimmung mit der EMV-Richtlinie (89/336/EWG), CE-Kennzeichen- Richtlinie (93/68/EWG) und Niederspannungsrichtlinie (73/23/EWG) hin. Auerdem zeigt das CE-Kennzeichen, dass an den mit Batteriestrom betriebenen Produkten unserer Firma angebracht ist, an dass das betreffende Gert mit der EMV-Richtlinie (89/336/ EWG) und der CE-Kennzeichen-Richtlinie (93/68/ EWG) bereinstimmt.

WICHTIGER HINWEIS FR KUNDEN Dieses Produkt wurde unter strenger Beachtung von Spezifikationen und Spannungsanforderungen hergestellt, die im Bestimmungsland gelten. Wenn Sie dieses Produkt ber das Internet, per Postversand und/ oder mit telefonischer Bestellung gekauft haben, mssen Sie besttigen, dass dieses Produkt fr Ihr Wohngebiet ausgelegt ist. WARNUNG: Verwendung dieses Produkts in einem anderen Land als dem, fr das es bestimmt ist, verwendet wird, kann gefhrlich sein und die Garantie des Herstellers oder Importeurs hinfllig lassen werden. Bitte bewahren Sie diese Quittung als Kaufbeleg auf, da andernfalls das Produkt von der Garantie des Herstellers oder Importeurs ausgeschlossen werden kann.

* Die ubrigen in dieser Bedienungsanleitung erwahnten Firmen-, Produkt-, Formatnamen usw. sind Warenzeichen oder eingetra-gene Warenzeichen der rechtlichen Eigentumer und werden ausdrucklich anerkannt.

50

Einleitung

Vielen Dank fr Ihre Entscheidung zu einem USB/MIDI Studio Controller der K-Serie. Bitte lesen Sie sich diese Anleitung vollstndig durch und benutzen Sie das Produkt nur in der angegebenen Weise. Bewahren Sie diese Bedienungsanleitung fr die sp- tere Bezugnahme an einem sicheren Ort auf. Diese Bedienungsanleitung bezieht sich auf folgende Gerte: K25, K49, K61 sowie K61P (dem ein separater Abschnitt gewid- met ist).

Die wichtigsten Funktionen Mehrere flexibel einsetzbare Steuerquellen.

ClickPoint-Funktion fr die Simultansteuerung zweier Parameter (X- und Y-Achse. Sie kann auch fr die Cursor-/Maussteuerung eines Programms genutzt werden.

Nach der Installation des beiliegenden M1 Le Soft-Synthis knnen Sie mit Ihrem K-Keyboard sofort Musik machen.

Das K61P enthlt 24 Klnge, deren Qualitt jener der Digital-Pianos von KORG entspricht. Es stehen Piano-, E. Piano- und Orgelklnge zur Verfgung.

Bedienelemente und ihre Funktionen

1

2

3 4 5

6 7 8 K61P

51

Bedienungsanleitung

1. Tastatur Hierbei handelt es sich um eine anschlagdynamische Standard-Tastatur.

2. ClickPoint Der ClickPoint-Funktion knnen zwei (einer fr die X- und einer fr die Y-Ach- se) MIDI-Steuerbefehle (CC) zugeordnet werden, was sich z.B. fr die Fernbedie- nung von Software-Synthesizern oder Recording-Programmen (DAWs) eignet, die Sie auf Ihrem PC installieren. Sie kann zudem als Computermaus missbraucht werden.

3. KNOB1/KNOB2 Diesen Reglern knnen separate MIDI-Steuerbefehle (CC) zugeordnet werden, was sich z.B. fr die Fernbedienung von MIDI-Gerten und Software eignet.

4. SW1- & SW2-Taster Diesen Tastern knnen beliebige MIDI-Steuerbefehle zwecks Fernbedienung ex- terner Gerte oder Programme zugeordnet werden. Auerdem kann man sie zum Senden von Programmwechseln (voriger/nchster Speicher) nutzen.

5. OCTAVE SHIFT UP & OCTAVE SHIFT DOWN Hiermit kann die Tonhhe in Oktavschritten gendert werden.

6. PITCH-Rad Erlaubt das zeitweilige Anheben/Absenken (Beugen) der Tonhhe.

7. MOD-Rad Dem Modulationsrad kann man einen beliebigen Steuerbefehl (CC) zuordnen und somit Software-Synthesizer oder eine DAW auf dem PC fernbedienen.

8. SLIDER Diesem Regler kann ein Steuerbefehl zwecks Fernbedienung eines Software-Syn- thesizers oder einer DAW zugeordnet werden. Er eignet sich besonders als Laut- strke- oder Expression-Regler.

Klangerzeugung (K61P)

1 2 3 4 5

1. VOLUME-Regler Hiermit kann die Lautstrke der internen Klangerzeugung eingestellt werden. De- ren Signale werden ber die OUTPUT-Buchsen (L/MONO, R) und den HEAD- PHONES-Anschluss ausgegeben.

2. BANK-Taster Mit jedem Klangwahltaster knnen drei Klnge gewhlt werden (es gibt 3 Bnke mit je 8 Klngen). Mit dem [BANK]-Taster whlen Sie die bentigte Bank.

52

3. PROGRAM-Taster Hiermit whlen Sie den gewnschten Klang innerhalb der aktuellen Bank.

4. REVERB-Taster Mit diesem Taster kann der Halleffekt ein-/ausgeschaltet werden. Auerdem lsst sich hiermit der Hallanteil einstellen.

5. CHORUS-Taster Mit diesem Taster kann der Chorus-Effekt ein-/ausgeschaltet werden. Auerdem lsst sich hiermit der Effektanteil einstellen.

Rckseite

1 2 3 4 5 6 7

Abbildung: Rckseite des K61P.

1. OUTPUT-Buchsen (nur auf dem K61P) Dies sind die Audio-Ausgnge der internen Klangerzeugung. Verbinden Sie sie mit den Eingngen eines Mischpults, einer Stereoanlage, eines Verstrkers usw.

2. HEADPHONES-Buchse (nur auf dem K61P) An diese Buchse kann ein Stereo-Kopfhrer (mit 1/4-Klinke) angeschlossen wer- den.

3. PEDAL-Buchse Ein Momentary-Pedal, wie der PS-1 Pedalschalter (beide getrennt erhltlich), kann an die Pedal-Buchse angeschlossen werden. Die K-Serie ermittelt beim Einschalten automatisch die Polaritt des angeschlossenen Pedals.

4. MIDI OUT-Buchse Verbinden Sie diese Buchse mit einem externen MIDI-Gert, wenn Sie es direkt ansteuern mchten. (Die MIDI OUT-Buchse der K-Serie, S. 56)

5. USB-Port ber diesen Port kann das K-Keyboard mit dem USB-Port des Computers ver- bunden werden.

6. Netzschalter Schieben Sie diesen Schalter zu DC (Netzteil) oder USB, um das Keyboard einzuschalten. Nach getaner Arbeit mssen Sie ihn in die STANDBY-Position schieben. (Anschlsse und Einschalten, S. 54)

7. Netzteilanschluss Schlieen Sie hier ein optionales Netzteil an. Solange Sie Ihr K mit einem Com- puter verwenden, kann die Speisung ber den USB-Bus erfolgen. Dafr bentigen Sie folglich kein Netzteil. Allerdings drfen Sie dann keinen passiven Hub verwen- den und kein MIDI-Modul o.. anschlieen.

53

Bedienungsanleitung

Vorbereitung

Installieren des MIDI-Treibers und der Software Inhalt der CD-ROM Die beiliegende CD-ROM enthlt folgende Dinge.

Editor fr die K-Serie KORG M1 Le Software-Synthesizer KORG USB-MIDI-Treiber fr Windows XP Installationshandbuch Bedienungsanleitung des K-Series Editor Bedienungsanleitung des M1 Le Software-Synthesizers Lizenzvereinbarung

Systemanforderungen MacOS X-Anwender Rechner

Apple Macintosh mit USB-Port, der die Anforderungen von Mac OS X erfllt

Untersttzte Betriebssysteme Mac OS X V.10.3 oder neuer

Windows XP-Anwender Rechner

Rechner mit USB-Port, der die Anforderungen von Microsoft Windows XP erfllt (ein USB-Chipsatz der Intel Corporation wird empfohlen)

Untersttzte Betriebssysteme Microsoft Windows XP Home Edition/Professional mit Service Pack 1 oder neuer

Installation Hinweise fr die Installation des KORG USB-MIDI-Treibers fr Windows XP, von K-Series Editor und dem M1 Le Software-Synthesizer finden Sie auf der beiliegenden CD-ROM.

Bitte lesen Sie sie sorgfltig durch Das Urheberrecht an allen Programmen, die sich auf dieses Produkt beziehen,

liegt bei der Korg Corporation. Die Lizenzvereinbarung fr die beiliegende Software finden Sie in einem separaten

Dokument. Lesen Sie sich die Lizenzvereinbarung genau durch, bevor Sie die Soft- ware installieren. Bereits durch die bloe Installation der Software geben Sie zu verstehen, dass Sie mit den Bestimmungen einverstanden sind.

Apple, Macintosh und MacOS sind eingetragene Warenzeichen der Apple Com- puter, Inc.

Windows XP ist in den USA und anderen Lndern ein eingetragenes Warenzeichen der Microsoft Corporation.

Alle anderen erwhnten Firmen- und Produktnamen sind Warenzeichen oder eingetragene Warenzeichen der betreffenden Eigentmer.

54

Anschlsse und Einschalten Schalten Sie alle beteiligten Gerte VOR Herstellen der Verbindungen AUS. Gehen Sie mit Bedacht vor, um weder Ihre Lautsprecher, noch die brigen Gerte zu beschdigen.

Verbindung per USB 1 Verbinden Sie die K-Serie ber ein USB-Kabel mit dem USB-Port des Computers.

2 Wenn Sie ein Pedal verwenden mchten, schlieen Sie es an die PEDAL-Buchse an.

Die K-Serie ermittelt beim Einschalten automatisch die Polaritt des angeschlos- senen Pedals. Wenn Sie ein Pedal angeschlossen haben, drfen Sie es beim Ein- schalten auf keinen Fall drcken.

3 Schalten Sie das K-Keyboard ein, indem Sie den Netzschalter in die USB-Posi- tion schieben.

Futaster

PEDAL-Buchse

Einstellung des Netzschalters

USB-Kabel

Computer

USB-Port

4 Stellen Sie den Netzschalter zum Ausschalten des Gerts auf STANDBY.

Bei Verwendung der USB-Verbindung bentigen Sie in der Regel kein Netzteil. Wenn Ihr Rechner aber nicht gengend Strom abgibt bzw. wenn Sie einen passi- ven Hub (ohne Stromversorgung) verwenden, reicht die Spannung eventuell nicht aus. Dann mssen Sie sich ein optionales Netzteil besorgen und den Netzschalter auf DC stellen.

Bei Verwendung der USB-Verbindung sendet die MIDI OUT-Buchse des K-Key- boards keine Befehle.

Verbindung via MIDI 1 Verbinden Sie das Netzteil zuerst mit dem betreffenden Anschluss des K-Key-

boards und anschlieend mit einer Steckdose.

2 Verbinden Sie das K-Keyboard ber ein MIDI-Kabel mit dem externen Modul usw.

55

Bedienungsanleitung

3 Wenn Sie ein Pedal verwenden mchten, schlieen Sie es an die PEDAL-Buchse an.

Die K-Serie ermittelt beim Einschalten automatisch die Polaritt des angeschlosse- nen Pedals. Wenn Sie ein Pedal angeschlossen haben, drfen Sie es beim Ein- schalten auf keinen Fall drcken.

4 Stellen Sie den Netzschalter auf DC. Die POWER-Diode leuchtet. Nun werden automatisch die zuletzt gespeicherten Einstellungen geladen.

5 Schalten Sie das externe MIDI-Modul ein.

MIDI IN

MIDI OUT

Futaster

MIDI-Kabel

Externes MIDI-Modul

PEDAL-Buchse

Einstellung des Netzschalters

Das Netzteil an eine Steckdose anschlieen.

Anschluss fr Netzteil

6 Nach getaner Arbeit mssen Sie zuerst das externe MIDI-Modul und danach das K-Keyboard ausschalten (STANDBY-Position).

Verwendung der internen Klangerzeugung (K61P) 1 Verbinden Sie das optionale Netzteil zuerst mit dem betreffenden Anschluss des

K-Keyboards und anschlieend mit einer Steckdose.

2 Verbinden Sie die Ausgnge mit den Eingngen des Verstrkers usw. Hierfr be- ntigen Sie Mono-Kabel (mit 1/4-Klinken). Fr den Mono-Einsatz brauchen Sie nur die L/MONO-Buchse anzuschlieen.

Stellen Sie mit dem VOLUME-Regler den Ausgangspegel der OUTPUT-Buchsen ein.

3 Stellen Sie den Netzschalter auf DC. Die POWER-Diode leuchtet.

4 Schalten Sie den verwendeten Verstrker usw. ein.

Kopfhrer

Aktivlautsprecher HEADPHONES-BuchseOUTPUT-Buchsen

INPUT

56

Die K-Serie und die Treiber-Ports Die K-Keyboards untersttzen 1 USB-MIDI-Eingangsport und 2 Ausgangsports.

Tastatur/-Regler/ Pitch-,Mod-Rad/ SW1/SW2/Pedal/ ClickPoint/ MIDI-Dumps

Treiber eines auf dem Computer laufenden Programms K-Serie

MIDI OUT-Gert

MIDI IN-Gert

MIDI OUT

KBD/KNOB

SOUND/CTRL *1

MIDI OUT-Buchse

MIDI-Dumps Klangerzeuger *2

*1 CTRL beim K25/49/61 *2 Nur K61P

MIDI IN-Gert KBD/KNOB KBD/KNOB dient fr die bertragung der von der Tastatur und den Bedienelementen erzeugten MIDI-Befehle. Wenn Sie ein Programm mit dem K-Keyboard fernbedienen mchten, mssen Sie diesen Port als MIDI-Eingang jenes Programms definieren. Auerdem dient KBD/KNOB fr die bertragung von Szenendaten. Dafr mssen Sie diesen Port als MIDI-Eingang fr den K- SeriesEditor definieren.

MIDI OUT-Gert MIDI OUT MIDI OUT dient fr die bertragung der vom Programm erzeugten MIDI-Befehle zur MIDI OUT- Buchse des K-Keyboards. Somit knnen jene Befehle auch an andere MIDI-Gerte weitergeleitet werden. Wenn Sie das K-Keyboard im USB-MIDI-Betrieb verwenden, aktivieren Sie hiermit dem- nach die Ausgabe des verwendeten Programms.

SOUND/CTRL (CTRL beim K25/K49/K61) SOUND/CTRL kmmert sich um den Empfang der vom Computer gesendeten Szenendaten. Dafr mssen Sie diesen Port als MIDI-Ausgang fr den K-SeriesEditor definieren. Im Falle des K61P dient dieser Port auerdem zum Ansteuern seiner internen Klangerzeugung.

Die MIDI OUT-Buchse der K-Serie Bei fehlender USB-Verbindung Es werden die auf der Tastatur und mit den Bedienelementen erzeugten MIDI-Befehle gesendet.

Bei vorhandener USB-Verbindung Es werden die auf dem Computer erzeugten MIDI-Befehle (ber den dort gewhlten MIDI OUT- Port) gesendet. Die auf der Tastatur und mit den Bedienelementen des K-Keyboards erzeugten MIDI-Befehle werden jedoch nicht gesendet.

57

Bedienungsanleitung

Wiederherstellen der Werksvorgaben Halten Sie bei Bedarf SW1 und SW2 gedrckt, whrend Sie das Keyboard einschalten, um wieder die Werkseinstellungen zu laden.

Die Controller Einstellungen des Werkszustands

Controller Funktion

SW1 / SW2 Program change (-1/+1)

KNOB1 CC#074 (Cutoff)

KNOB2 CC#079 (EG Intensity)

SLIDER CC#007 (Volume)

PITCH wheel Fixed (Pitch Bend)

MOD wheel CC#001 (Modulation)

PEDAL CC#064 (Damper)

ClickPoint Mouse mode

* Die Angaben in den Klammern beziehen sich auf M1 Le.

58

Bedienung Die Einrichtung des K-Keyboards muss mit dem beiliegenden K-SeriesEditor-Pro- gramm erfolgen.

Die MIDI-Befehle werden auf dem Global-Kanal gesendet.

Tastatur (Keyboard) De Tastatur sendet Notenbefehle. Das Anschlagverhalten kann anhand dreier Kurven bzw. als Fixwert (127) definiert werden.Auerdem lsst sich die Tonhhe hher und tiefer transponieren.

ClickPoint Der X- (links/rechts) und Y-Achse (auf/ab) knnen separate MIDI-Steuerbefehle zugeordnet werden. Mithin lassen sich zwei Parameter ansteuern. Die ClickPoint-Funk- tion kann alternativ als Computermaus fungieren. Die Mglichkeiten lauten No Assign/Control Change/Mouse.

No Assign Es werden keine Daten gesendet.

Control Change [0...127] Whlen Sie die Steuerbefehlsnummern (CC). Die entsprechenden MIDI-Parameter werden beim Auslenken in X- bzw. Y-Richtung angesteuert. Nach der Freigabe kehrt die ClickPoint-Funktion zurck zur Mitte. Sie knnen die zu- letzt gewhlte X-/Y-Einstellung aber verriegeln, indem Sie den Taster drcken. Drc- ken Sie den Taster erneut, um die Parameterwerte zurckzustellen.

Mouse Mode Wenn Sie hier Mouse whlen, fungiert die ClickPoint-Funktion als Maus-Fernbedie- nung Ihres PCs. Mit dem Taster knnen Sie folglich Symbole anklicken.

Die ClickPoint-Funktion kann nur als Maus verwendet werden, wenn Sie eine USB- Verbindung herstellen.

KNOB1 und KNOB2 Den Reglern 1 & 2 knnen MIDI-Steuerbefehle (CC) zugeordnet werden, was sich z.B. fr die Fernbedienung von Software-Synthesizern oder DAWs eignet, die Sie auf Ihrem PC installieren. Die Mglichkeiten lauten No Assign/Control Change.

No Assign Es werden keine Daten gesendet.

Control Change [0...127] KNOB1 und KNOB2 erlauben das Ansteuern der zugeordneten Parameter.

59

Bedienungsanleitung

SW1- & SW2-Taster Bei Drcken des [SW1]- oder [SW2]-Tasters wird der zugeordnete MIDI-Befehl ab- wechselnd als An- und Aus-Wert gesendet. Die Mglichkeiten fr SW1 und SW2 lauten No Assign/Program Change/Control Change.

No Assign Es werden keine Daten gesendet.

Program Change Mit [SW1] kann die Programmnummer um jeweils 1 Einheit verringert werden. Mit [SW2] kann die Programmnummer um jeweils 1 Einheit erhht werden. Drcken Sie [SW1] und [SW2] gemeinsam, um die Programmnummer 0 zu senden.

Control Change [0...127] [SW1] und [SW2] sind einem Steuerbefehl mit Schaltfunktion zugeordnet und senden folglich An- und Aus-Befehle. Im Toggle-Modus mssen Sie [SW1] bzw. [SW2] wiederholt drcken, um den ange- steuerten Parameter abwechselnd ein- und auszuschalten. Im Momentary-Modus sendet [SW1] bzw. [SW2] so lange den An-Wert, bis Sie den Taster wieder freigeben. Bei der Freigabe wird der Aus-Wert gesendet.

[OCTAVE SHIFT UP]- & [OCTAVE SHIFT DOWN]-Taster Hiermit kann die Tastatur in Oktavschritten transponiert werden. Der Einstellbereich ist nicht fr alle Ausfhrungen gleich.

K-Keyboard Oktavbereich

K25 4+4

K49 4+4

K61/K61P 3+3

Leuchtstatus Oktavierung

Aus 0 Oktaven

Grn +1/1 Oktave

Orange +2/2 Oktaven

Rot +3/3 Oktaven

Rotes Blinken +4/4 Oktaven (nur beim K25/K49)

PITCH-Rad Bewegen Sie dieses Rad auf oder ab, um Pitch Bend-Befehle (Tonhhenbeugung) zu senden.

60

MOD-Rad Dem Modulationsrad kann man bei Bedarf einen beliebigen Steuerbefehl (CC) zuord- nen, was sich z.B. fr die Fernbedienung von Software-Synthesizern und Hardware- Gerten eignet. Die Mglichkeiten lauten No Assign/Control Change/Aftertouch.

No Assign Es werden keine Daten gesendet.

Control Change [0...127] Mit dem MOD-Rad kann die gewhlte Funktion stufenlos angesteuert werden.

After Touch Bei Auslenken des MOD-Rades werden Aftertouch-Befehle gesendet.

SLIDER Diesem Regler kann ein Steuerbefehl zwecks Fernbedienung eines Software-Synthe- sizers oder einer DAW zugeordnet werden. Die Mglichkeiten lauten No Assign/Control Change.

No Assign Es werden keine Daten gesendet.

Control Change [0...127] Mit dem SLIDER kann die gewhlte Funktion angesteuert werden.

PEDAL Auch dem an die PEDAL-Buchse angeschlossenen Futaster kann ein beliebiger MIDI- Befehl zugeordnet werden (er muss also nicht unbedingt als Haltepedal fungieren). Die Mglichkeiten lauten No Assign/Control Change.

No Assign Es werden keine Daten gesendet.

Control Change [0...127] Der Futaster ist einem Steuerbefehl mit Schaltfunktion zugeordnet und sendet folg- lich An- und Aus-Befehle. Im Toggle-Modus mssen Sie den Futaster wiederholt bettigen, um den angesteu- erten Parameter abwechselnd ein- und auszuschalten. Im Momentary-Modus sendet der Futaster so lange einen An-Wert, bis Sie ihn wieder freigeben. Bei der Freigabe wird der Aus-Wert gesendet.

61

Bedienungsanleitung

Verwendung der Klangerzeugung (K61P)

Anwhlen von Klngen Mit den 8 Programmtastern knnen 24 verschiedene (8 x 3) Klnge gewhlt werden. Folglich mssen Sie auch die bentigte Bank whlen. Um z.B. den Clav-Klang zu whlen, mssen Sie zuerst den sechsten Programmtaster von links drcken(damit er leuchtet). Whlen Sie anschlieend BANK2.

1 Drcken Sie den Taster des gewnschten Klangs.

2 Whlen Sie mit dem BANK-Taster die bentigte Bank. Durch wiederholtes Drcken whlen Sie der Reihe nach BANK1, BANK2 und BANK3. Die Diode der gewhlten Bank leuchtet jeweils.

[PROGRAM]-Taster

[PIANO 1]

[PIANO 2]

[PIANO 3]

[PIANO 4]

[PIANO 5]

[PIANO 6]

[HARPSI 1]

[HARPSI 2]

Bank2

E. Piano 1

E. Piano 2

Soft E.P.

Vintage E.P.

E.P. Pad

Clavi

Vibraphone

Choir

Bank3

Jazz Organ 1

Jazz Organ 2

Jazz Organ 3

Church Organ 1

Church Organ 2

Church Organ 3

Strings

Slow Strings

Osz.

2

2

1

1

2

1

1

2

Osz.

1

1

1

1

2

1

1

1

Osz.

2

2

2

3

1

1

1

2

Bank1

Grand Piano 1

Grand Piano 2

Standard Piano

Bright Piano

Honky Tonk Piano

Mellow Piano

Harpsichord 1

Harpsichord 2

Klangbersicht

* [PROGRAM]-Taster= Name der BANK 1-Klnge. * Anzahl der Oszillatoren, die fr jede Note bentigt werden.

Effekte Reverb (Hall) Mit diesem Effekt erwecken Sie den Eindruck, dass Sie in einem Konzertsaal o.. spielen. Auf Englisch nennt man diesen Halleffekt Reverb.

1 Whlen Sie mit dem [REVERB]-Taster den Hallanteil (Effektlautstrke). Die Farbe der Tasterbeleuchtung informiert Sie ber die gewhlte Einstellung.

Farbe des [REVERB]-Tasters Hallanteil

Aus Aus

Grn Ein wenig

Orange Normal

Rot Viel

62

Chorus Mit diesem Effekt erwecken Sie den Eindruck, dass ein Part von mehreren Musikern gleichzeitig gespielt wird.

1 Drcken Sie den [CHORUS]-Taster wiederholt, um den gewnschten Chorus-Anteil zu wh- len. Die Farbe der Tasterbeleuchtung informiert Sie ber die gewhlte Einstellung.

[CHORUS]-Taster Chorus-Anteil

Aus Aus

Grn En wenig

Orange Normal

Rot Viel

Einstellungen Den Einstellungsmodus des K61P whlt man, indem man den [BANK]-Taster des K- Keyboards lngere Zeit gedrckt hlt. Die Diode des BANK-Tasters und die 8 Programm- taster erlschen. Whlen Sie mit einem der 8 Programmtaster den nderungsbedrftigen Parameter. Jener Programmtaster beginnt zu blinken. Nun kann durch Drcken einer Klaviaturtaste der gewnschte Wert eingestellt werden. Besttigen Sie Ihre Eingabe durch erneutes Drcken des [BANK]-Tasters. Damit verlassen Sie dann auch den Ein- stellungsmodus. Der Einstellungsmodus umfasst die folgenden Parameter:

[PROGRAM]-Taster

[PIANO 1]

[PIANO 2]

[PIANO 3]

[PIANO 4]

[PIANO 5]

[PIANO 6]

[HARPSI 1]

[HARPSI 2]

Bedeutung

Anwahl der Tastaturansprache

Anwahl einer anderen Tonart" fr die Tastatur

Stimmen des Instruments

Anwahl eines Stimmungssystems

Festlegen des bertragungs-/Empfangskanals

Verbindung mit der Klangerzeugung

Aktivieren/Deaktivieren von Programmwechseln

Aktivieren/Deaktivieren von Lautstrkenderungen

Funktion

Anschlagkurve

Transposition

Stimmung

Stimmungssystem

Global-Kanal (MIDI)

Local-Funktion

Programmwechselfilter

Lautstrkefilter

* [PROGRAM]-Taster= Name der BANK 1-Klnge.

Anschlagkurve Es stehen 3 Anschlagkurven sowie eine Fixeinstellung (mit dem Wert 127) zur Verf- gung. Whlen Sie die fr Sie praktischste Einstellung.

1 Halten Sie den [BANK]-Taster gedrckt, um den Einstellungsmodus des K-Key- boards zu aktivieren.

2 Drcken Sie den 1 [PIANO 1/E.P. 1/ORGAN 1]-Taster (er beginnt zu blinken).

3 Bettigen Sie die Taste der gewnschten Einstellung: C4 (leicht), C#4 (normal), D4 (hart) oder D#4 (fester Anschlagwert).

C8C7C6C5C4C3C2C1

63

Bedienungsanleitung

4 Drcken Sie den [BANK]-Taster, um den Einstellungsmodus zu verlassen.

Leicht Leise ( )

Hart

Laut ( ) Leicht

Hart

Normal

Anschlag

Ausgangs- pegel

Note Bedeutung C4 Leicht (selbst mit relativ leichtem Anschlag

werden schon laute Noten erzielt)

C#4 Normal (Ansprache wie auf einem Klavier) D4 Har t (fr laute Noten muss man hr ter

hinlangen) D#4 Fest (alle Noten haben den Wert 127)

Die Wahl der Anschlagkurve gilt sowohl fr die gesendeten MIDI-Befehle als auch fr die interne Klangerzeugung.

Transposition Wenn Sie die Tastatur transponieren, knnen Sie Stcke in schwierigen Tonarten mit einem leichteren/dem gewohnten Fingersatz spielen. Die Tastatur kann 1 Oktave (1212) hher oder tiefer transponiert werden.

1 Halten Sie den [BANK]-Taster gedrckt, um den Einstellungsmodus des K-Key- boards zu aktivieren.

2 Drcken Sie den 2 [PIANO 2/E.P. 2/ORGAN 2]-Taster (er beginnt zu blinken). Whlen Sie mit den Tasten C3~C5 die gewnschte Einstellung.

C8C7C6C5C4C3C2C1

-12 +120

3 Mit der Taste C4 wird die Transposition ausgeschaltet.

4 Drcken Sie den [BANK]-Taster, um den Einstellungsmodus zu verlassen.

Das gewhlte Transpositionsintervall gilt sowohl fr die gesendeten MIDI-Befehle als auch fr die interne Klangerzeugung.

Stimmung Bei Bedarf knnen Sie die Stimmung des K61P (das ja eine Klangerzeugung enthlt) an jene anderer Instrumente oder Stcke angleichen.

1 Halten Sie den [BANK]-Taster gedrckt, um den Einstellungsmodus des K-Key- boards zu aktivieren.

2 Drcken Sie den 3 [PIANO 3/E.P. 3 ORGAN 3]-Taster (er beginnt zu blinken).

3 Drcken Sie die Taste C4 wiederholt, um die Tonhhe um jeweils 0,5Hz anzuhe- ben. Drcken Sie die Taste B3 wiederholt, um die Tonhhe um jeweils 0,5Hz abzusenken.

C8C7C6C5C4C3C2C1

64

Drcken Sie die Tasten B3 und C4 gleichzeitig, um die Kammertonfrequenz wieder auf A4= 440Hz zu stellen.

4 Drcken Sie den [BANK]-Taster, um den Einstellungsmodus zu verlassen.

Beim Ausschalten wird die Stimmung wieder auf A4= 440Hz gestellt.

Stimmungssystem Hiermit knnen Sie ein anderes Stimmungssystem whlen. Die Wahl eines anderen Stimmungssystems eignet sich vor allem fr klassische Barockmusik. Das K61P bietet drei Stimmungssysteme: Kirnberger, Werckmeister und die gleichschwebende Temperierung (die in der westlichen Welt fast ausnahmslos verwendet wird).

1 Halten Sie den [BANK]-Taster gedrckt, um den Einstellungsmodus des K-Key- boards zu aktivieren.

2 Drcken Sie den 4 [PIANO 4/E.P. 4/ORGAN 4]-Taster (er beginnt zu blinken).

3 Bettigen Sie die Taste des gewnschten Stimmungssystems: C4 (Kirnberger), C#4 (Werckmeister) oder D4 (gleichschwebend).

C8C7C6C5C4C3C2C1

4 Drcken Sie den [BANK]-Taster, um den Einstellungsmodus zu verlassen.

Note

C4

C#4

D4

Stimmung Werckmeister: Die Werckmeister III-Stimmung, die im

Sptbarock vom Musikwissenschaftler und Organisten

Andreas Werckmeister entwickelt wurde, um in unter-

schiedlichen Tonarten spielen zu knnen.

Kirnberger: Die Kirnberger III-Stimmung von Johann Philip

Kirnberger (frhes 18. Jahrhundert). Diese Stimmung wird vor

allem fr Cembali verwendet.

Gleichschwebende Stimmung: Die heutzutage am weitesten

verbreitete Stimmung. Der Abstand zwischen allen Noten betrgt

exakt einen Halbton. Somit ist die Tonart vllig unerheblich.

Beim Ausschalten wird wieder die gleichschwebende Stimmung gewhlt.

Ein Wort zum Stretch Tuning-Verfahren Mit dieser leicht gedehnten Stimmung erzielt man oftmals einen wrmeren Klang. Hier werden die Noten im Bass etwas zu tief und jene im Diskant etwas zu hoch gestimmt. So etwas eignet sich vor allem fr Klavierklnge. 6 Klnge des K-Keyboards verwen- den dieses Stimmungssystem:

65

Bedienungsanleitung

Programmtaster BANK 1

[PIANO1] Grand Piano 1

[PIANO2] Grand Piano 2

[PIANO3] Standard Piano

[PIANO4] Bright Piano

[PIANO5] Honky Tonk Piano

[PIANO6] Mellow Piano

Einstellen des MIDI-Kanals Die MIDI-Kommunikation funktioniert nur, wenn das K-Keyboard und das Empfnger- gert denselben MIDI-Kanal verwenden. Der Einstellbereich fr den MIDI-Kanal lautet 1~16.

1 Halten Sie den [BANK]-Taster gedrckt, um den Einstellungsmodus des K-Key- boards zu aktivieren.

2 Drcken Sie den 5 [PIANO 5/E.P. 5/ORGAN 5]-Taster (er beginnt zu blinken).

3 Drcken Sie eine Taste im Bereich C4~D#5. Die Tasten sind folgenden MIDI-Kanlen zugeordnet: C4= Kan. 1, C#4= Kan. 2, D4= Kan. 3 D#5= Kan. 16

C8C7C6C5C4C3C2C1

4 Drcken Sie den [BANK]-Taster, um den Einstellungsmodus zu verlassen.

Der gewhlte MIDI-Kanal gilt sowohl fr die gesendeten MIDI-Befehle als auch fr die interne Klangerzeugung.

Local-Funktion Diesen Parameter brauchen Sie nur, wenn Sie die Verbindung zwischen der Tastatur sowie den Spielhilfen einerseits und der internen Klangerzeugung des K61P anderer- seits lsen mchten, um nur noch externe Klangerzeuger anzusteuern. Bei Verwen- dung eines Sequenzers mit MIDI Echo-Funktion (oder hnlich) verhindern Sie hier- mit, dass jede Note doppelt ausgegeben wird. Solange die Local-Funktion aktiv ist, gibt die interne Klangerzeugung die gespielten Noten ebenfalls wieder.

1 Halten Sie den [BANK]-Taster gedrckt, um den Einstellungsmodus des K-Key- boards zu aktivieren.

2 Drcken Sie den 6 [PIANO 6/CLAVE/ORGAN 6]-Taster (er beginnt zu blinken).

3 Drcken Sie die Taste C4, um die Funktion einzuschalten. Mit dem C#4 deaktivieren Sie sie.

C8C7C6C5C4C3C2C1

66

4 Drcken Sie den [BANK]-Taster, um den Einstellungsmodus zu verlassen.

Local-Einstellung

Tastatur/Bedienelemente

Computer K61P

KBD/KNOB

SOUND/CTRL Klangerzeugung

Local-Funktion an

Computer

KBD/KNOB

SOUND/CTRL

Local-Funktion aus

Tastatur/Bedienelemente

K61P

Klangerzeugung

Beim Ausschalten wird der Local-Parameter wieder aktiviert.

Aktivieren/Filtern von Programmwechseln Bei Anwahl eines anderen Klangs auf dem K61P wird die entsprechende MIDI- Programmnummer gesendet. Wenn solche MIDI-Programmwechsel Ihnen die Arbeit eher erschweren als erleichtern, knnen Sie ihre Ausgabe unterdrcken.

1 Halten Sie den [BANK]-Taster gedrckt, um den Einstellungsmodus des K-Key- boards zu aktivieren.

2 Drcken Sie den 7 [HARPSI 1/VIBE/STRINGS 1]-Taster (er beginnt zu blinken).

C8C7C6C5C4C3C2C1

3 Drcken Sie die Taste C4, um die Funktion einzuschalten. Mit dem C#4 deaktivieren Sie sie.

67

Bedienungsanleitung

4 Drcken Sie den [BANK]-Taster, um den Einstellungsmodus zu verlassen.

Filtern von Lautstrkebefehlen Auch die Steuerbefehle (CC07) fr Lautstrkenderungen der internen Klangerzeugung knnen gefiltert werden. Wenn dieser Parameter aktiv ist, reagiert die interne Klanger- zeugung auf CC07-Befehle, die (nach der entsprechenden Zuordnung) von KNOB1/ KNOB2 oder dem SLIDER gesendet werden. Wenn dieser Parameter aus ist, reagiert die interne Klangerzeugung nicht auf CC07- Befehle, die (nach der entsprechenden Zuordnung) von KNOB1/KNOB2 oder SLIDER gesendet werden.

1 Halten Sie den [BANK]-Taster gedrckt, um den Einstellungsmodus des K-Key- boards zu aktivieren.

2 Drcken Sie den 8 [HARPSI 2/CHOIR/STRINGS 2]-Taster (er beginnt zu blinken).

C8C7C6C5C4C3C2C1

3 Drcken Sie die Taste C4, um die Funktion einzuschalten. Mit dem C#4 deaktivieren Sie sie.

Verhalten der CC07-Befehle

AN AUS

KE

Spielhilfen

K61P

Spielhilfen

K61P

KE

Computer Computer

* KE: Klangerzeuger Lautstrkeregelug des KEs Lautstrke des KEs.

4 Drcken Sie den [BANK]-Taster, um den Einstellungsmodus zu verlassen.

68

Fehlersuche Das Gert kann nicht eingeschaltet werden

Befindet sich der Netzschalter in der richtigen Position? (Anschlsse und Einschalten, S. 54)

Haben Sie das K-Keyboard ber einen Hub mit Ihrem Computer verbunden? Wenn ja, sollten Sie ein Netzteil verwenden.

Der Treiber kann nicht eingerichtet werden

Wahrscheinlich wird der Vorgabetreiber von Windows verwendet. Installieren Sie den beiliegenden Treiber.

Legen Sie die beiliegende CD-ROM ordnungsgem in das CD-Laufwerk.

Reinigen Sie bei Bedarf den Lesekopf des CD-Laufwerks. Verwenden Sie zur Suberung einen handelsblichen CD-Reiniger.

Die Software reagiert nicht

Haben Sie das USB-Kabel ordnungsgem angeschlossen?

Wird das K-Keyboard berhaupt vom Computer erkannt?

Bestimmte Hardware-Einstellungen knnen die USB-Anmeldung des K-Keyboards unmglich machen.

Vielleicht untersttzt das angeschlossene Gert bzw. das verwendete Programm den gesendeten Befehl nicht. Siehe die Bedienungsanleitung des Gerts/Pro- gramms, um in Erfahrung zu bringen, ob der betreffende Befehl untersttzt wird.

Sie hren nichts (K61P)

Vielleicht haben Sie die Lautstrke ja auf 0 gestellt. Erhhen Sie die Lautstrke.

Die gespielten Noten werden zu frh ausgeschaltet

Wahrscheinlich berfordern Sie die Polyphonie Ihres K61P.

Apropos Polyphoniestimmen Mit Polyphoniestimmen ist im Grunde die Anzahl der Noten gemeint, die ein Instrument simultan wiedergeben kann. Wenn Sie mehr Noten zu spielen versuchen, werden die zuerst gespielten ausgeschaltet, um Platz zu machen fr neuere Noten. Das fhrt dazu, dass bestimmte Noten entweder gar nicht oder viel zu kurz hrbar sind. Die Polyphonie des K61P richtet sich nach der Anzahl der gebotenen Oszillatoren sowie der verwendeten Effekte. Bei bestimmten Klngen werden fr jede Note auerdem zwei Oszillatoren bentigt. Die maximale Polyphonie fr Klnge, die nur 1 Oszillator je Note bentigen (z.B. HARPSI/ VIBES) betrgt 60 Noten. Klnge, die 2 Oszillatoren beanspruchen (darunter Grand Pi- ano 1 [PIANO 1, Bank A] und Grand Piano 2 [PIANO 2, Bank A]), erlauben hingegen das Spielen von jeweils 30 Noten. Fr den Halleffekt werden 10 Oszillatoren bentigt. Der Chorus-Effekt begngt sich mit deren 3 (die also nicht mehr zum Spielen von Noten zur Verfgung stehen).

69

Bedienungsanleitung

Technische Daten Bedienelemente

Tastatur: 25, 49, 61 anschlagdynamische Tasten (normale Gre) ClickPoint-Funktion Definierbare Regler 2 Definierbare Taster 2 Oktavierungstaster (auf/ab) Pitch Bend-Rad Definierbares Modulationsrad Schieberegler 1

Interne Klangerzeugung (K61P) Klangerzeugung Stereo-Sampling Polyphonie 60 (maximal) Klnge 24 (3 Bnke 8) Tonhhenfunktionen Transposition, Feinstimmung Stimmungssysteme Gleichschwebend, Kirnberger, Werckmeister Effekte Hall, Chorus (jeweils 3 Pegelstufen)

Anschlsse Pedalbuchse MIDI OUT-Buchse USB-Buchse Buchse fr Netzteil (DC9V) Ausgnge (L/MONO, R, nur beim K61P) Kopfhreranschluss (nur beim K61P)

Stromversorgung Stromversorgung ber den USB-Bus (bei Verwendung des USB-Ports) DC9V-Netzteil (Sonderzubehr)

Stromverbrauch K25/K49/K61: Speisung ber USB-Bus 110mA

Bei Verwendung eines DC9V-Netzteils 120mA K61P: Speisung ber USB-Bus 300mA

Bei Verwendung eines DC9V-Netzteils 320mA

Abmessungen (B H T) K25: 489 221 69 mm K49: 818 221 69 mm K61/K61P: 982 221 69 mm

Gewicht K25: 1.5 kg K49: 2.4 kg K61: 2.9 kg K61P: 3.1 kg

70

Lieferumfang USB-Kabel CD-ROM (mit M1 Le Software-Synthesizer, K-Series Editor, Treiber, Installations-

Wizard usw.) Bedienungsanleitung MIDI-Implementierungstabelle Software-Lizenzvereinbarung

Systemanforderungen Macintosh

Betriebssystem: Mac OS X V.10.3 oder neuer Rechner: Apple Macintosh mit USB-Port, der die Anforderungen von Mac OS X

erfllt Windows

Betriebssystem: Microsoft Windows XP Home Edition/Professional Rechner: Rechner mit USB-Port, der die Anforderungen von Windows XP erfllt

(ein USB-Chipsatz der Intel Corporation wird empfohlen)

Sonderzubehr Netzteil Futaster/Pedal PS-1

nderungen der technischen Daten und Funktionen ohne vorherige Ankndigung vorbehalten.

(Stand: Dezember 2005)

MIDI Implementation Chart

Date : 2006. 1. 10

K25/K49/K61

Basic Channel

Default Changed

Aftertouch

Pitch Bend

Polyphonic (Key) Monophonic (Channel)

Program Change Variable Range

System Real Time

Clock Command

System Exclusive

System Common

Song Position Song Select Tune

Mode 1: OMNI ON, POLY Mode 2: OMNI ON, MONO : Yes Mode 3: OMNI OFF, POLY Mode 4: OMNI OFF, MONO : No

Aux Messages

Local On/Off All Notes Off Active Sense Reset

Velocity Note On Note Off

Note Number: True Voice

Mode Memorized Messages Altered

0 127

1 127 64

0 127

Memorized

[MIDI STUDIO CONTROLLER]

MOD wheel

*1 *1

Notes *1: Transmitting by allocating it to the controller becomes possible. *2: It corresponds to Device Inquiry message besides KORG System Exclusive message.

PITCH wheel

Control Change

0127

1 16 1 16

Function Transmitted Recognized Remarks

*2

*1

Controllers (KNOB1/2, SW1/2, Slider, ClickPoint, MOD wheel, Pedal)

MIDI Implementation Chart

Date : 2006. 1. 10

K61P

Basic Channel

Default Changed

Aftertouch

Pitch Bend

Polyphonic (Key) Monophonic (Channel)

Program Change Variable Range

System Real Time

Clock Command

System Exclusive

System Common

Song Position Song Select Tune

Mode 1: OMNI ON, POLY Mode 2: OMNI ON, MONO : Yes Mode 3: OMNI OFF, POLY Mode 4: OMNI OFF, MONO : No

Aux Messages

Local On/Off All Notes Off Active Sense Reset

Velocity Note On Note Off

Note Number: True Voice

Mode Memorized Messages Altered

0 127

1 127 64

0 127

Memorized

[MIDI STUDIO CONTROLLER]

MOD wheel

*1 *1

Notes *1: Transmitting by allocating it to the controller becomes possible. *2: It receives it when the setting of Volume message filer is off. *3: It sends and receives it when enable/disable setting of the program change is enable. *4: It corresponds to Device Inquiry message besides KORG System Exclusive message.

PITCH wheel

Control Change

1 7

10 11 64 66 67

120 121

0-127

1 16 1 16

Function Transmitted Recognized Remarks

*4

*1

Modulation wheel Volume *2 Panpot Expression Damper Sostenuto Soft Pedal

All Sound Off Reset All Controlle

Manualsnet FAQs

If you want to find out how the K-Series K61p KORG works, you can view and download the KORG K-Series K61p Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for KORG K-Series K61p as well as other KORG manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a KORG K-Series K61p. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the KORG K-Series K61p Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This KORG K-Series K61p Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download KORG K-Series K61p Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print KORG K-Series K61p Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the KORG K-Series K61p Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.