Kleenmaid LWK320 Ironing Board User Manual PDF

1 of 2
1 of 2

Summary of Content for Kleenmaid LWK320 Ironing Board User Manual PDF

107843 Issue B ECN: 04097

Note: Generic model is shown. Actual product may differ.

SPECIFICATION DIAGRAM Model LWK320

(Dimensions in mm)

I N S T A L L A T I O N I N S T R U C T I O N

PLEASE READ THE ENTIRE INSTRUCTION BEFORE INSTALLING THE LWK320 IRONING CENTRE KIT SET

1. Disconnect LWK320 Ironing Centre Kit Set Console from power supply. (Ensure the power is switched off)

2. Insert small screwdriver or slim knife as shown, ease catch to side and slip out diffuser.

3. Replace lamp (40 watt max.)

4. Slide diffuser back into aperture and click into place. (Turn power back on)

An external ON/Off safety power socket must be installed inside the wall behind the cabinet. Plug the console into the socket. Alternatively the unit can be hard wired directly to an isolation switch by an electrician. The plug or switch must remain accessible after the installation.

LWK320 Ironing Centre Kit Set

NOTE: The LWK320 Ironing Centre Kit Set is designed to fit a 400mm wide, (368mm Internal,kitchen / laundry cabinet. Please ensure your cabinet fits the following dimensions as shown on the next page. NOTE: Please take care when predrilling holes not to drill all the way through or damage the cabinet. The screws supplied with all kits are designed for 16mm thick cabinet panels. Different screws may be needed if the cabinet panels are less than 16mm thick.

CONSOLE INSTALLATION

1. Drill the 50mm hole in the top cabinet face for the electrical cable (Diagram C). If through sheetmetal the 50mm hole needs deburring. 2. Remove diffuser from console using a slim knife or flat bladed screw driver (Diagram D). 3. Remove Lamp (Bayanet Cap). 4. Position the console on the top cabinet face with the diffuser removed. Mark out the 3 mounting hole positions on the cabinet face or alternatively use the dimension provided to pre-drill the 3 mounting holes (Diagram B). 5. Drill out the 3 marked holes for the supplied screws. 6. Feed the electrical cable through the 50mm hole. Position the console with the 3 mounting holes. Using the supplied screws attach the console to the top cabinet face. 6. Replace lamp. 7. Slide diffuser back into aperture and click into place.

CONNECTING THE CONSOLE TO ELECTRIC POWER

Pivot Rod

Back Stop

Pivot Stop

BOARD INSTALLATION

Installation Kit Includes - 2 x Board retainer Screws - 16 x Ironing Board Screws

- 3 x Console Screws

E

D

Top Cabinet Face

Console Mounting

Holes

C

91 15

17 0

10 5

40

A

Front of Cabinet

L A M P R E P L A C E M E N T

15 0*

400*

150

16*

40

82 .5

35 86 .550

B

Centered

368

1. Pre-drill holes in the cabinet on both sides 3.0mm, for the screws supplied as per diagram A. 2. Attach one (1) height adjustment bracket to the cabinet using the screws supplied. 3. Insert the ironing board pivot rod and pivot stop into the attached bracket. While supporting the ironing board attach the other bracket to both the pivot rod and pivot stop (Diagram E). 4. Move the board into position so the free bracket lines up with the pre-drilled holes and secure using the supplied screws. 5. Position the back stop behind the pivot stop in the middle of the cabinet and mark out hole position. Drill 4 holes, 3.0mm, for the screws supplied. Attach the back stop (Diagram E). 6. The board retainer is to be positioned as shown on the first page (Diagram F). Mark out the screw holes and drill 2.5mm for the supplied screws. 7. Attach board retainer. 8. Fit the board cover with the silver/gray coating facing up.

600*

154

16 5

21 00

*

16 30

68 0

A

* Recommended / typical dimensions.

366 126

91

165

366

100

192

11 25 295

310

395

675

15 0

Board Retainer

Console

Ironing Board

F Diagram

Should you be fitting a door to the enclosure holding this LWK320 Ironing Centre Kit Set, please be mindful of the position of all door furniture (hinges, handles, etc.) Specifically ensure the board will operate without obstruction.

107843 Issue B ECN: 04097

O P E R A T I N G I N S T R U C T I O N

L W K 3 2 0 I R O N I N G C E N T R E K I T S E T F E A T U R E S

The LWK320 Ironing Centre Kit Set has the following features:

Integrated cotton coated rayon cover Right or left hand Round corners board Built in 230-240 volt power outlet 40 watt light Digital auto timer 3 level height adjustable Board swivels a full 180

o

2

1

To open the Ironing Board, lift board retainer and lower the board. To store Ironing Board, follow the steps in reverse order.

The Ironing Board has three working heights. To adjust the board:

1 With the board in the horizontal position hold the board with one hand near the base (NOT BY THE NOSE) and support the pivot rod 1 with the other hand. 2 Adjust the Ironing board to the desired position by lifting the board by the pivot rod (NOT BY THE NOSE) and moving it to the required height.

NOTE: in order to store the Ironing board, it may need to be in the lowest position depending on your cabinet construction.

SWIVEL BOARD 180O

3 POSITIONS HEIGHT ADJUSTMENT

Console

MANUFACTURED FOR:

BY: ROBINHOOD LIMITED

6 ZELANIAN DRIVE, EAST TAMAKI AUCKLAND, NEW ZEALAND

ISO9001 Certified

M A I N T E N A N C E YOUR LWK320 IRONING CENTRE KIT SET BOARD IS NOW FITTED WITH A HEAT RESISTANT

COVER. TO AVOID DAMAGE TO THE MATERIAL

PLEASE DO NOT WASH THE COVER The laminated surface of the unit may be

wiped clean with non abrasive household cleaner.

WARNING 1) Do not place EXCESSIVE WEIGHT (weight should not exceed 15kg) on the Ironing

Board when opened as it is designed to accept normal ironing use only. 2) Iron not to exceed 2360 Watt. 3) Allow iron to cool down before storing in the cabinet. 4) Empty water reservoir and turn off steam action prior to storing iron. 5) Turn power off when not in use. 6) Do not remove the board retainer. 7) The appliance is not intended for use by young children or infirm persons

without supervision. 8) Young children shall be supervised to ensure that they do not play with the

appliance. 9) The appliance is supplied with an approved power cable which must not be

changed. If the supplied cord of this equipment is damaged, it must only be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid hazard.

10) Upon installation, ensure that the socket outlet or ON/OFF switch remains easily accessible after installation.

D I G I T A L T I M E R O P E R A T I N G I N S T R U C T I O N S

1. As the uni t is powered up, two ser ies of beeps are given. 2. 00m00s is displayed. 3. Press MIN button once to advance the minute sect ion by 1 or hold down for an incremental increase in minutes. 4. (Opt ional) Press SEC button once to advance the second sect ion by 1 or hold down for an incremental increase in seconds. 5. When there is a change in set t ings a beep is given. 6. To start or stop the t imer anyt ime press the START/STOP but ton. 7. When the t imer is count ing down the red LED is on. 8. When the t imer reaches zero, power to the 3 pin socket and l ight is d isconnected and a ser ies of beeps wi l l sound. The t imer wi l l then revert to the or ig inal set t ings. Press any key to stop the beep sound. 9. To reset the t imer

Manualsnet FAQs

If you want to find out how the LWK320 Kleenmaid works, you can view and download the Kleenmaid LWK320 Ironing Board User Manual on the Manualsnet website.

Yes, we have the User Manual for Kleenmaid LWK320 as well as other Kleenmaid manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Kleenmaid LWK320. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Kleenmaid LWK320 Ironing Board User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Kleenmaid LWK320 Ironing Board User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Kleenmaid LWK320 Ironing Board User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Kleenmaid LWK320 Ironing Board User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Kleenmaid LWK320 Ironing Board User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.