Karcher BRC 30 15 C 1.008-058.0 Operator's Manual PDF

1 of 50
1 of 50

Summary of Content for Karcher BRC 30 15 C 1.008-058.0 Operator's Manual PDF

Register your product www.kaercher.com/welcome 86348550-N 09/11/19

BRC 30/15 C English 02

LISTED

2

Warranty Registration Thank you for purchasing a Krcher North America product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product.

To register your product go to : http://warranty.karcherna.com/

For customer assistance: 1-800-444-7654

MODELS:

BRC 30/15 C 1.008-058.0

BRC 30/15 C *JP 1.008-055.0

BRC 30/15 C HD

1.008-657.0

86348550 BRC 30/15 C

Machine Data Label

Overview

The carpet extractor is a mains powered, portable extractor intended for commercial use. The appliance sprays a cleaning solution onto the carpet, agitates the wet carpet, and then extracts the soiled solution back into the units recovery tank. The appliance can be fitted with an accessory tool for cleaning upholstery and stairs.

3

Table of Contents

Machine Data Label . . . . . . . . . . . . . . . . . . . . . . . . 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . 3

How To Use This Manual . . . . . . . . . . . . . . . . . . . 4

Safety IMPORTANT SAFETY INSTRUCTIONS . . . . . . . 5 CONSIGNES DE SCURIT IMPORTANTES . . 6 HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . 7 NIVEAU D'INTENSIT DU DANGER. . . . . . . . . . 8 Grounding Instructions . . . . . . . . . . . . . . . . . . . . . 9 Safety Label Location . . . . . . . . . . . . . . . . . . . . . 10

Operations Technical Specifications . . . . . . . . . . . . . . . . . . . 11 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Controls & Components . . . . . . . . . . . . . . . . . . . 13 Filling The Solution Tank . . . . . . . . . . . . . . . . . . 14 Operating The Machine . . . . . . . . . . . . . . . . . . . 15 Operating Machine With Accessory Tools . . . . . 16

Maintenance Protect From Freezing . . . . . . . . . . . . . . . . . . . . 17 Daily Regular Maintenance. . . . . . . . . . . . . . . . . 17 Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . 17 Maintenance Instructions . . . . . . . . . . . . . . . . . . 18 Brush Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 18 Spray Jet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Brush Motor Removal . . . . . . . . . . . . . . . . . . . . . 19 Pump Removal . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Vacuum Motor Removal . . . . . . . . . . . . . . . . . . . 20 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 21

PARTS Brush Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Decal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Handle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Solution 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Solution 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Tank & Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Vacuum. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Wiring Diagram - Vacuum, Brush Motor & Pump 44 Hose Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Suggested Spare Parts. . . . . . . . . . . . . . . . . . . . 47

86348550 BRC 30/15 C

4

How To Use This Manual

This manual contains the following sections:

HOW TO USE THIS MANUAL

SAFETY

OPERATIONS

MAINTENANCE

PARTS LIST

The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.

Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual.

The model and serial number of your machine is located on the lower back panel.

The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death.

The OPERATIONS section is to familiarize the operator with the operation and function of the machine.

The MAINTENANCE section contains preventive maintenance to keep the machine and its compo- nents in good working condition. They are listed in this general order:

Periodic

Daily/Regular

Troubleshooting

The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information:

REF - column refers to the reference number on the parts illustration.

PART NO. - column lists the part number for the part.

PRV NO. - Reference number.

QTY - column lists the quantity of the part used in that area of the machine.

DESCRIPTION - column is a brief description of the part.

SERIAL NO. FROM - column indicates the first machine the part number is applicable to. When the machine design has changed, this column will indicate serial number of applica- ble machine. The main illustration shows the most current design of the machine. The boxed illustrations show older designs. If column has an asterisk (*), call manufacturer for serial number.

NOTES - column for information not noted by the other columns.

NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts.

NOTE: The manual part number is located on the lower left corner of the front cover.

86348550 BRC 30/15 C

5

Safety

IMPORTANT SAFETY INSTRUCTIONS When using this machine, basic precaution

must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

To reduce the risk of fire, electric shock, or injury:

Connect to a properly grounded outlet. See Grounding Instructions.

Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service.

Use only indoors. Do not use outdoors or expose to rain.

Do not allow machine to be used as a toy. Close attention is necessary when used by or near children.

Use only as described in this manual. Use only manufacturer's recommended components and attachments.

Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center.

Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners.

Do not run machine over cord. Keep cord away from heated surfaces.

Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.

Do not handle the electrical plug or machine with wet hands.

Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.

This machine is intended for cleaning carpet only.

Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

This machine is not suitable for picking up health endangering dust.

Turn off all controls before unplugging.

Do not operate this machine near flammable fluids, dust or vapors.

This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes.

Maintenance and repairs must be done by qualified personnel.

If foam or liquid comes out of machine, switch off immediately.

READ AND SAVE THESE INSTRUCTIONS

86348550 BRC 30/15 C

6

Safety

CONSIGNES DE SCURIT IMPORTANTES Lors de l'utilisation de cette machine, des prcautions de base

doivent toujours tre prises, y compris les prcautions suivantes :

LIRE TOUTES LES INSTRUCTIONS AVANT D'UTILISER CETTE MACHINE.

Pour rduire le risque d'incendie, d'lectrocution ou de blessure :

Raccordez l'appareil une prise adquatement relie la terre. Voir les Consignes de mise la terre.

Ne laissez pas l'appareil sans surveillance lorsqu'il est branch. Dbranchez l'appareil lorsqu'il n'est pas utilis et avant tout entretien.

Utilisez-le exclusivement dans des endroits ferms. Ne l'utilisez pas en plein air et ne le laissez pas sous la pluie.

Ne pas permettre aux enfants dejouer avec l'appareil. Durant la manoeuvre de la machine, prendre garde aux personnes environnantes et notamment aux enfants.

Utilisez-le exclusivement de la manire dcrite dans ce manuel. Utilisez exclusivement les composants et les fixations recommands par le fabricant.

N'utilisez pas l'appareil si le cordon ou la fiche est endommag(e). Observez toutes les consignes figurant dans ce manuel au sujet de la mise la terre de l'appareil. Si l'appareil ne fonctionne pas correctement, s'il est tomb par terre, s'il est endommag, s'il a t laiss dehors ou s'il a t plong dans l'eau, veuillez le renvoyer un centre d'entretien agr.

Ne tirez pas sur le cordon, ne portez pas l'appareil par le cordon, n'utilisez pas le cordon comme poigne, ne fermez pas une porte sur le cordon, ne tirez pas sur le cordon dans des angles ou des coins pointus.

Ne faites pas passer l'appareil par-dessus le cordon. Maintenez le cordon l'cart de surfaces chauffes..

Ne dbranchez pas l'appareil en tirant sur le cordon. Pour le dbrancher, empoignez la fiche, non pas le cordon.

Ne manipulez pas la fiche ou l'appareil les mains mouilles.

Ne faites pas fonctionner l'appareil si des ouvertures sont bouches. Dgagez des ouvertures tous dbris susceptibles d'entraver le passage de l'air.

Cette machine est destine pour nettoyer le tapis seulement.

Ne pas ramasser quelque chose qui brle ou fume, comme des cigarettes, des allumettes ou des cendres chaudes.

Cet appareil n'est pas conu pour aspirer des poussires dangereuses.

Arrtez toutes les commandes avant le dbranchement.

Ne faites pas fonctionner cet appareil proximit de fluides, de poussires ou de vapeurs inflammables.

Cet appareil est adapt un usage commercial : par exemple dans les htels, les tablissements scolaires, les hpitaux, les usines, les magasins et les bureaux, des fins plus tendues qu'un simple entretien de la maison.

Les travaux de maintenance et de rparation doivent absolument tre effectus par du personnel qualifi.

Si de la mousse ou du liquide s'chappe de la machine, teignez-la immdiatement.

CONSERVEZ CES CONSIGNESS

86348550 BRC 30/15 C

7

Safety

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions:

WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.

FOR SAFETY: To Identify actions which must be followed for safe operation of equipment. Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel.

FOR SAFETY: DO NOT OPERATE MACHINE: Unless Trained and Authorized. Unless Operation Guide is Read and understood. In Flammable or Explosive areas. In areas with possible falling objects

WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use manufacturer approved replacement parts.

86348550 BRC 30/15 C

8

Safety

Les symboles suivants sont utiliss dans tout ce manuel, tels que dcrits ici:

NIVEAU D'INTENSIT DU DANGER

Il existe trois niveaux d'intensit du danger, identifis par des termes d'avertissement - AVERTISSEMENT, ATTENTION et POUR VOTRE SCURIT. Le niveau d'intensit du danger est dtermin par les dfinitions suivantes :

AVERTISSEMENT - Les dangers ou des pratiques contraires la scurit qui POURRAIENT entraner des blessures personnelles ou la mort.

ATTENTION - Les dangers ou des pratiques contraires la scurit qui pourraient entraner des blessures personnelles lgres ou des dgts sur le produit ou d'autres biens.

POUR DES RAISONS DE SCURIT : Pour identifier les actions qui doivent tre excutes pour un fonctionnement sr de l'quipement. Signaler immdiatement tout dommage subi par la machine ou fonctionnement dfectueux. Ne pas utiliser la machine si elle ne fonctionne pas correctement. Ci-dessous se trouvent les informations indiquant les condi- tions potentiellement dangereuses pour l'oprateur ou l'quipement. Lire attentivement ces informations. tre conscient que ces conditions peuvent survenir. Reprer tous les dispositifs de scurit sur la machine. Suivre les tapes ncessaires de formation du personnel qui utilise la machine.

POUR DES RAISONS DE SCURIT : NE PAS FAIRE FONCTIONNER LA MACHINE : Sauf si le personnel est form et autoris. Sauf si le manuel d'utilisation est lu et compris. Dans des zones inflammables ou explosives. Dans des zones contenant des objets susceptibles de tomber

LORS DE L'ENTRETIEN DE LA MACHINE : viter les pices mobiles. Ne pas porter de vtements, vestes, chemises ou manches vagues lors de l'entretien de la machine. Utiliser les pices de rechange approuves par le fabricant.

86348550 BRC 30/15 C

9

Safety

THIS PRODUCT IS FOR COMMERCIAL USE ONLY.

Electrical

In the USA this machine operates on a standard 15 amp 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.

Extension Cords

If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length.

Grounding Instructions

This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordi- nances.

120 Volt Models

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in "Fig. A". A temporary adaptor that looks like the adaptor in "Fig. C" may be used to connect this plug to a 2-pole receptacle as shown in "Fig. B", if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (Fig. A) can be installed by a qualified electrician. The green colored rigid ear, lug, or wire extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Le raccordement incorrect du conducteur de terre d'quipement peut entraner des risques d'lectrocu- tion. Vrifiez auprs d'un lectricien qualifi ou d'un responsable de l'entretien si vous avez quelque doute que ce soit quant au raccordement la terre de votre prise murale. Ne modifiez pas la fiche fournie avec l'appareil: si elle ne correspond pas la prise murale, faites installer une prise adquate par un lectricien qualifi.

86348550 BRC 30/15 C

GROUNDING PIN

GROUNDED OUTLET

ADAPTER

METAL SCREW TAB FOR GROUNDING SCREW

GROUNDED OUTLET BOX

(A) (B) (C)

10

Safety

Safety Label Location

The following WARNING LABEL(S) are found on your cleaning unit. These labels point out important Warnings and Cautions which should be followed at all times. Failure to follow warnings and cautions could result in fatality, personal injury to yourself and/or others, or property damage. Follow these instructions carefully! DO NOT remove these labels.

NOTE: If at any time the labels become illegible, promptly replace them.

Les tiquettes D'avertissement suivantes se trouvent sur votre unit de nettoyage. Ces tiquettes signalent les avertissements et mises en garde importantes qui doivent tre suivis en tout temps. Le non respect des avertissements et mises en garde pourrait entraner des dommages matriels, des blessures graves ou mme la mort. Suivez attentivement ces instructions ! NE PAS retirer ces tiquettes.

REMARQUE : Si, tout moment, les tiquettes deviennent illisibles, remplacez-les rapidement.

WARNING LABEL PART NUMBER 86220140

86348550 BRC 30/15 C

11

Operations

Technical Specifications

ITEM MEASURE

Vacuum Motor (1) 3 stage, 1.5hp 100 cfm (2.8cubic meters/min.) Waterlift - 120 (305cm)

Floating Brush 10 (25.4cm)

Main Jet Solution Pump Solenoid Style

Accessory Solution Pump Solenoid Style

Solution Capacity 4.6 Gal (17.3L)

Recovery Capacity 3.9 Gal (14.7L)

Brush Speed 1160 rpm

Wheels (2) 10 dia. (25cm) by 2 (5cm)

Vacuum Shoe 12 (30.48cm) cast aluminum

Solution Spray 1 quick change jet

Power cord 25 (7.6m) (14 gauge)

Height 39 inches (100cm) (Handle adjusted to highest position)

Length 27 inches (69cm) (Handle adjusted to highest position)

Width 14 inches (36cm)

Weight 75 lbs. (34kg)

Electrical 115V, 15A, 60Hz

86348550 BRC 30/15 C

Width Length

Height

12

Operations

To avoid electric shock use indoors only.To reduce risk of fire, do not use volatile substances. Use only cleaners intended for carpet application.

Pour viter une lectrocution, utilisez la machine l'intrieur seulement. Pour rduire les risques d'incendie, n'utilisez pas de substances volatiles. Utilisez seulement des nettoyants destins tre appliqus sur les tapis.

Inspection

Carefully unpack and inspect your extractor for shipping damage. Each unit is operated and thor- oughly inspected before shipping, and any damage is the responsibility of the carrier, who should be notified immediately.

To avoid possible distortion of polyethylene solution/ recovery tanks, DO NOT USE WATER TEMPERA- TURE THAT EXCEEDS 140F (60 C).

Pour viter toute distorsion possible aux rservoirs de rcupration /de la solution de polythylne, NUTILISEZ PAS D'EAU DONT LA TEMPRATURE DPASSE 60 C (140 F).

Chemicals

Use only the suitable chemicals listed below. Using incompatible chemicals will damage the machine. Damages of this type are not covered under warranty. Carefully read ingredients on manufac- turer's label before using any product in this machine.

Suitable Chemicals Incompatible Chemicals

Alkalis Aldehydes; Butyls

Defoaming Agents Carbon Tetrachloride

Detergents Chlorinated Bleaches

Soaps Chlorinated Hydrocarbons

Vinegar Trichlorethylene

Hydroxides Phenols; Methyls (MEK)

Perchlorethylene (perc)

Aromatic Hydrocarbons

D-Limonene

86348550 BRC 30/15 C

13

Operations

2

1

9

3

8

6 7

10

11

12

13

5

4

86348550 BRC 30/15 C

Controls & Components

1. Power and Operation Mode Switch

Turns accessory tool on or machine on.

2. Main Handle

3. Solution Button

Sprays solution on floor when pressed.

4. Brush Motor Circuit Breaker

Protects brush motor from overheating.

5. Vac Motor Circuit Breaker

Protects the vac motor from overheating

6. Handle Adjustment Lever

Adjusts handle position.

7. Solution Tank Drain Hose

8. Accessory Tool Connection

Solution connection for accessory tools.

9. Accessory Hose Connection

Hose connection for accessory tool.

10. Dome Clamp

11. Dome

12. Recovery Tank

13. Solution Tank

14

Operation

Filling The Solution Tank

1. Release dome clamp.

2. Lift upper recovery tank from machine and set aside.

3. Use a clean bucket, recovery tank or hose to fill solution tank with hot water. The solution tank holds 4 gallons (15.2 liters) of cleaning solution.

Add a non-foaming concentrate for use in hot water extractors at the proportions noted on the container.

NOTE: Periodically operate the extractor with only hot water to remove chemical residue in carpet.

To avoid possible distortion of the polyethylenesolu- tion/recovery tanks, DO NOT USE WATER WITH A TEMPERATURE THAT EXCEEDS 140F(60C).

4. Place recovery tank back on machine.

Place dome on recovery tank. Make sure dome is seated correctly to ensure proper vacuum seal. Clamp dome securely to recovery tank.

Use only the suitable chemicals listed in the Chemical Section. Using incompatible chemicals will damage the machine. Carefully read ingredients on manufacturer's label before using any product in this machine.

SPECIAL NOTES:

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowl- edge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

The sound pressure level at the operator's ear was measured to be 73.7 dBA. This was a nearfield, broad-band measurement taken in a typical industrial environment on a tile floor. This appliance contains no possible source of impact noise. The instanta- neous sound pressure level is below 63 Pa.

The weighted root mean square acceleration at the operator's arms was measured to be below 2.5m/s2. This was a tri-axial, third-octave-band measurement made during normal operation on a composite tile floor. The measurement and related calculations were made in accordance with ISO 5349-1.

86348550 BRC 30/15 C

15

Operation

Operating The Machine

1. Vacuum the carpet and make sure it is cleared of surface debris before cleaning.

2. Plug power cord into a grounded wall outlet.

NOTE: Defeating the grounding pin on the power cord can result in a severe electrical shock.

3. Turn on the machine by pressing the switch in the normal operation mode.

NOTE: The vacuum and the brush are protected by circuit breakers located on the control panel, to the right of the switch.

NOTE: If either motor does not respond to being switched on, reset the circuit breakers by pressing them in, and attempt to switch the machine on again.

NOTE: If solution does not dispense in an even pattern across the width of the machine, the spray jet may be clogged. Tilt the machine back, check for debris and clean surface of jet.

NOTE: Do not use pins, wire, etc. to clean spray jet nozzle as this will deform the jet and destroy the spray pattern.

4. To operate the machine, pull straight back without pushing down on handle. Press the solution spray button to apply cleaning solution.

5. While operating machine, check for excessive foam buildup in the recovery tank. If excessive foam is present, add a defoamer solution to recovery tank, or empty tank.

6. Empty recovery tank when approximately 3/4 full. If the recovery tank is overfilled, the water will drain back onto the carpet when the vacuum is switched off.

7. Ventilate area after carpet has been cleaned.

Keep children and pets away and do not walk on carpet until it is dry.

A Windblower fan can be used to reduce drying time.

86348550 BRC 30/15 C

16

Operation

Operating Machine With Accessory Tools

This extractor is easily adapted for use with accessory tools: Contact Customer Service for details.

1. Disconnect vacuum hose at dome, insert hose cuff into the dome, ensuring that there is a tight fit. Dome must be clamped to recovery tank.

2. Attach the solution hose from accessory tool to the brass solution fitting on the back of machine.

3. Turn on the switch in the accessory position. The application of cleaning solution is now controlled by the lever on the accessory tool.

NOTE: The solution pump is not intended to run dry. When using the extractor for vacuum pick-up only. Do not press the solution spray button.

This appliance is not suitable for picking up hazardous dust.

Cet appareil n'est pas conu pour aspirer des poussires dangereuses.

86348550 BRC 30/15 C

17

Maintenance

Protect From Freezing

If it becomes necessary to store in temperatures that could drop below 40F, the pumping system, hoses and valves must be protected from freezing with a methyl hydrate window washer antifreeze solution.

NOTE: Do not use ethylene glycol or cooling system antifreezes.

1. Add one gallon of window washer antifreeze to the supply tank.

2. Turn on pump switch and spray until the anti- freeze solution fills the solution lines.

3. Drain the leftover antifreeze from the supply tank. Always allow the unit to reach room temperature before filling with hot water or operating.

4. Before operation be sure to flush system completely. Failure to do so after winterizing machine will damage carpet.

Daily Regular Maintenance Before making any adjustments or repairs to the machine, disconnect the power cord from the electrical source.

1. Empty unused cleaning solution from the solution tank.

2. Inspect and clean filter at solution tank fill port and at the vacuum intake port in the dome.

3. Flush pumping system with 1 to 2 gallons of clean, hot water.

4. Check spray jet for full spray pattern.

5. Empty the recovery tank and rinse with clean water.

6. Check for and remove any lint or debris around brush and vac shoe.

Periodic Maintenance

1. After every 25 hours of operation, flush a white vinegar solution (ONE quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system.

2. If the spray jet becomes clogged, check for debris and clean surface of jet.

NOTE: Do not use pins, wire, etc. to clean spray jet nozzle as this will deform the jet and destroy the spray pattern.

3. Periodically inspect all hoses, electrical cables, filters, gaskets and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss.

4. The electrical cable must be well insulated, if the cable insulation is broken or frayed, repair or replace it immediately. Don't take chances with electrical fire or shock.

5. The filter in the bottom of the solution tank and at the fill port must be clean to allow free flow of cleaning solution. The screen filter on the vacuum intake in the dome must be free of lint buildup to ensure full vacuum strength.

6. The dome gasket must be properly seated and free of damage to create the air seal needed to extract water.

86348550 BRC 30/15 C

18

Maintenance

Maintenance Instructions

Remove machine power cord from electrical source before making any adjustments or repairs to the machine.

Retirez le cordon d'alimentation de la machine de la source lectrique avant de procder des rparations ou des ajustements de la machine.

Only qualified maintenance personnel are to perform repairs.

Seul le personnel d'entretien qualifi peut effectuer des rparations.

Brush Assembly

1. Turn off switch and unplug machine.

2. Position the machine to have access to the bottom. Remove screws (2) at the sides of the machine holding the brush deck pivot axle.

3. Remove screw mounting belt cover and remove belt cover.

4. Loosen the nuts (2) at brush motor and slide motor forward to reduce belt tension. Remove belt.

5. Loosen set screw on brush pulley. Remove pulley.

6. Remove screws (4) mounting brush bearings to frame. Slide bearing off brush axle.

7. Remove brush by lifting drive end out of frame and sliding other end out of bearings mounted to frame.

8. Inspect/replace brush and bearings as required. The brush is equipped with yellow wear indicator bristles. Replace the brush when it wears down to the height of the yellow bristles.

9. Reverse the process to reinstall the brush and bearings. Check belt for proper belt tension.

Only use the brushes provided with the appliance or those specified in the instruction manual. The use of other brushes may impair safety.

N'utilisez que les brosses fournies avec l'appareil ou celles qui sont spcifies dans le manuel d'instructions. L'utilisation d'autres brosses peut nuire la scurit.

Spray Jet NOTE: To prevent a clogged jet due to alkali build- up, the spray system should be flushed with 1 to 2 gallons of clean hot water at the end of each day.

1. Turn off switch and unplug machine.

2. Position the machine to have access to the bottom. Remove screws (2) at the sides of the machine holding the brush deck pivot axle.

3. Position the machine to have access to the bottom.

4. Pull off the clip mounting the jet to the frame. Push the jet and hose out of the mounting hole in the frame.

5. Loosen the hose clamp and pull the jet out of the hose.

6. Reverse the process to reinstall the jet. Be sure to have jet rotated correctly before installing clip. Clip tab must face back of machine.

NOTE: Do not use pins or wire to remove obstruction if clogged, this may damage jet and alter spray pattern.

86348550 BRC 30/15 C

19

Maintenance

Brush Motor Removal

1. Turn off switch and unplug machine.

2. Set the machine in its upright position. Remove the screws (2) in the back metal cover. Rotate the cover down and slide back releasing the tab under the machine from the main frame.

3. Remove the pump box cover. Remove screws (4) at each leg of the cover.

4. To remove brush motor, position the machine to have access to the bottom. Remove screws (2) at the sides of the machine holding the brush deck pivot axle.

5. Remove screw mounting belt cover and remove belt cover.

6. Remove the nuts and washers (2) at brush motor and slide motor forward to reduce belt tension. Remove belt.

7. Remove pulley by loosening set screw and pull off shaft.

8. Unplug the brush motor wires from the rectifier located in the pump mount housing. Also, remove the ground lug from the stud on the main frame by removing the nut on the stud.

9. Reverse the process to reinstall the motor. Align motor pulley with brush pulley. Check belt for proper belt tension.

Pump Removal

1. Turn off switch and unplug machine.

2. Set the machine in its upright position. Remove the screws (2) in the back metal cover. Rotate the cover down and slide back releasing the tab under the machine from the main frame.

3. Remove the pump box cover. Remove screws (4) at each leg of the cover.

4. To remove either pump, loosen the hose clamp and remove the hose from both ends of the pump.

5. Remove screws and washers (4) that mount pump housing.

6. Unscrew the hose fittings from each end of the pump.

7. Flex the pump mounting housing to remove the pump.

8. Remove the screw attaching the ground wire to the pump. Remove the other two wire connectors attached to the pump.

9. Reverse the process to reinstall.

86348550 BRC 30/15 C

20

Maintenance

Vacuum Motor Removal

1. Turn off switch and unplug machine.

2. Set the machine in its upright position. Remove the screws (2) in the back metal cover. Rotate the cover down and slide back releasing the tab under the machine from the main frame.

3. Remove the pump box cover. Remove screws (4) at each leg of the cover.

4. Remove vacuum hose, loosen hose clamp and pull hose from bottom of vacuum motor.

5. Unplug wires (2) from main harness located in pump mount housing. Remove ground from stud on main frame.

6. To remove the vacuum motor, remove the screws (2) in the back of the machine that mount the plastic cover to the solution tank.

7. Remove the screws (3) that mount the vacuum motor to the plastic cover. Pull the cover off the vacuum motor.

8. Unscrew the ground wire from the vacuum motor.

9. Reverse the process to reinstall the vacuum motor.

NOTE: Make sure the excess wire lengths do not get pinched between the vacuum motor and plastic cover.

NOTE: The vacuum motor is protected by a circuit breaker located in the switch panel. The breaker will only trip under conditions of abuse.

3 8

[9.5mm]

Vacuum Motor Carbon Brushes

Carbon Brushes

End Cap

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important: These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less tan 3/8" (9.5mm) long.

86348550 BRC 30/15 C

21

Maintenance

Troubleshooting

PROBLEM CAUSE SOLUTION

No power, nothing runs. Is the cord plugged in. Plug in cord.

Circuit breaker tripped in building. Reset breaker.

Faulty switch. Call for service.

Faulty power cord or pigtail. Call for service.

Vacuum motor will not run. Vacuum circuit breaker tripped. Reset breaker.

Faulty main switch. Call for service.

Loose wiring. Call for service.

Faulty vac motor. Call for service.

Vacuum motor runs but suction is poor.

Debris lodged in vac shoe. Remove debris from vac shoe.

Dome gasket defective or missing. Replace as necessary.

Vacuum hose cracked or hose cuff loose Replace or repair as necessary.

Recovery tank full. Turn off vacuum motor. Drain and rinse recovery tank.

Poor or no water flow.

(carpet is streaky) Switch to accessory mode. Turn to deep clean position.

Jets clogged or missing. Jets clogged or missing.

Solution filter clogged. Drain solution tank and clean solution- filter.

Faulty solution pump. Call for service.

Brush does not spin. Switch in accessory mode. Turn to deep clean position.

Brush circuit breaker tripped. Reset circuit breaker.

Brush belt broken. Replace as necessary.

Faulty brush motor. Call for service.

Accessory tool fitting difficult to connect

Corrosion on fitting.

Clean with steel wool. Remove and soak in acetic acid (white vinegar). Lubricate lightly with silicone base lubricant.

86348550 BRC 30/15 C

22

Maintenance

Troubleshooting

Problem Cause Solution

Worn brush bearings Squealing or grinding sound in brush housing.

Replace bearings.

Carpet not getting clean

Severe soil conditions Make several passes at right angles to each other. Use a pre-spray.

Carpet too wet Worn spray jet Replace spray jet which is producing a fine mist.

Carpet not getting wet

Solution filter screen clogged. Clean solution filter screen located inside lower tank.

Spray jet clogged. Clean or replace jet. Do not use a wire to clean jet. Damaged jet will cause over-saturation.

Pump not running. Check for and correct any loose wires. Repair or replace.

Faulty solution switch. Replace switch in handle.

86348550 BRC 30/15 C

23

PARTS

BRC 30/15 C 1.008-058.0

BRC 30/15 C *JP 1.008-055.0

BRC 30/15 C HD

1.008-657.0

86348550 BRC 30/15 C

24

Brush Deck

16

1 7

6

1

2

3

4

5

17

8 9

10 11

12

13

14

15

17

86348550 BRC 30/15 C

2586348550 BRC 30/15 C

Brush Deck

REF PART NO. QTY DESCRIPTION SERIAL NO.

FROM NOTES

1 86173020 5 SCR, M5 X 10, PHMS, ISO7045, SS

2 86217390 1 COVER, PULLEY, BRUSH DECK

3 86215260 1 BELT, HTD 5MM 69T 9 WIDE

4 86223780 2 SET SCR, M4 X 6LG, CP BLK

5 86223300 1 PULLEY, BRUSH

6 86214970 1 AXLE, PIVOT, BRUSH DECK

7 86229020 2 BEARING, BRUSH PLASTIC

8 86005640 2 NUT, 10-32 HEX NYLOCK

9 86173330 2 WASHER, M5, FLAT, ISO7093, SS

10 86247110 1 MOTOR, 115V BRUSH DRIVE

11 86217920 1 BRKT, FLOATING BRUSH, 10 IN

12 86223490 2 RING, 10MM EXT SNAP, DIN 471

13 86216430 2 BUSHING, BRUSH PRESSURE

14 86216040 1 BRUSH, CHEVRON, 10 IN

15 86173220 2 SCREW, M6-1 X 12 FLGHBTNHMS SS

16 86223350 1 PULLEY, MOTOR

17 86010680 1 WASHER, 3/8 ID X 3/4 OD NYLON

26

Control Panel

1

2

3

6 5

8 7

9

4

86348550 BRC 30/15 C

27

Control Panel

SEE WIRING DIAGRAM FOR WIRE CONNECTIONS.

REF PART NO. QTY DESCRIPTION SERIAL NO.

FROM NOTES

1 86007200 1 SWITCH, DPDT 3-POSITION ROCKER

2 86002010 2 BOOT, 3/8 CIRCUIT BREAKER

3 86173140 2 SCR, KA40X16, PT OVAL,WN1412, PL

4 86350630 1 ASM, CTRL PNL, BRC 30/15 C

SPARE ASM INCLUDES

86347130 AND 86217410

5 86230140 1 BREAKER, 1.5A CIRCUIT

6 86291460 1 BRAKER, 11A VDE CIRCUIT

7 86292300 2 SCR, M4X20 SBHCS, BLK EDP

8 86173350 2 WASHER, M5, FLAT, ISO7089, SS

9 86216300 2 BUMPER, CONSOLE

86348550 BRC 30/15 C

28

Decal

2

1

3

4

5

6

86348550 BRC 30/15 C

2986348550 BRC 30/15 C

Decal

REF PART NO. QTY DESCRIPTION SERIAL NO.

FROM NOTES

1 86347130 1 LABEL, CTRL PNL, BRC 30/15 C

2 86395860 1 LABEL, DOME ACCESSORY

3 86013720 1 LABEL, MINI EXT. INSTRUCTION

4 86335160 1 LABEL, KARCHER FRONT

4b 86435700 1 LABEL HOME DEPOT LOGO DOMED 10086570

ONLY

5 86401330 2 LABEL, SIDE, BRC 30/15 C

6 86437430 1 LABEL HOME DEPOT RENTAL 10086570

ONLY

30

Frame & Wheels

11

13

7

6

5 4

3

2

1

10

8

9

12

86348550 BRC 30/15 C

31

Frame & Wheels

REF PART NO. QTY DESCRIPTION SERIAL NO.

FROM NOTES

1 86215830 1 BRKT, BRUSH HOUSING, 10 IN

2 86173010 6 SCR, M4 X 16, SHCS, ISO4762, SS

3 86216290 1 BUMPER, EXTRACTOR, FRONT

4 86218090 1 GASKET, VAC SHOE

5 86225530 1 VAC SHOE, 12 IN

6 86172630 6 NUT, M4, LOCK, ISO7040, SS

7 86173220 6 SCREW, M6-1 X 12 FLGHBTNHMS SS

8 86226050 2 WHEEL, 10IN

9 86011880 2 WASHER, 16.2 X 23 X 0.6MM, PLT

10 86214980 1 AXLE, WHEELS, 5/8 DIA

11 86272750 2 RING, 5/8 EXTERNAL SNAP

12 86300070 2 HUBCAP, 9.75" WHEEL

13 86291130 1 BUMPER, BRUSH DECK

86348550 BRC 30/15 C

32

Handle

35

4 14

9

10

11

12

29

31

27 26

25

24

30

8

7

3

6

36 2

1

21 20

19

12

17 16 15

28

33 34

35

5

4

22

18

13

23

32

37

86348550 BRC 30/15 C

3386348550 BRC 30/15 C

Handle

REF PART NO. QTY DESCRIPTION SERIAL NO.

FROM NOTES

1 86173140 4 SCR, KA40X16, PT OVAL WN1412, PL

2 86297150 1 HANDLE, GRIP, TOP

3 86225140 1 SWITCH, MICRO TONELUCK

4 86006770 2 SCR, 10-32 X 1/4 PHTR PLTD

5 86013730 1 SHIELD, MICROSWITCH

6 86297160 1 HANDLE, GRIP, BOTTOM

7 86224650 1 SPRING, BUTTON

8 86216470 1 BUTTON, SPRAY HANDLE

9 86292550 1 BUSHING, HANDLE LOCK

10 86296610 1 LEVER, CAM HANDLE

11 86347140 1 COVER, HANDLE HUB, LEFT, YLW

12 86277600 3 SCR, M4 X 20, PHMS, ISO7045, SST

13 86296620 AS

REQ'D WASHER, 0.2X19.8X25.0MM PLTD

14 86219460 1 HUB, HANDLE SPLINE

15 86218220 1 GASKET, CONTROL BOX LEFT

16 86173320 3 WASHER, M4, FLAT, DIN125 SST

17 86173030 3 SCR, M4 X 6, PHMS, ISO7045, PL

18 86266630 1 PIN, DOWEL 5 X 25MM, PLTD

19 86292560 1 SHAFT, HANDLE LOCK

20 86222340 1 NUT, M12, LOCK, ISO 7040, SST

21 86259430 1 WASHER, M12 FLAT

22 86288680 4 WASHER, M5 RIVET BACKUP

23 86172870 4 SCR, M4X14 PHMS, ISO7045, SST

24 86217350 1 COVER, CONTROLS BOTTOM

25 86217380 1 COVER, TUBE HUB RIGHT

26 86224140 1 SHAFT, HANDLE

27 86224460 1 SPACER, HANDLE BUSHING

28 86218230 1 GASKET, CONTROL BOX RIGHT

29 86173220 4 SCREW, M6-1 X 12 FLGHBTNHMS SS

30 86215520 1 BRACKET, HANDLE AXLE

31 86224930 1 STRAIN RELIEF, 14/3 STRAIGHT

32 86233170 1 CLAMP, 3/8 NYLON UL/CSA

33 86005640 1 NUT, 10-32 HEX NYLOCK

34 86270800 1 NUT, 10-32 HEX SS

35 86010640 2 WASHER, #10 LOCK EXT STAR SS

36 86298790 1 WELDMENT, HANDLE TUBE

37A 86217140 1 CORD ASM, 14X3 SJTX25' MPRO

37B 86360840 1 CORD ASM, 14X3, 25 PSE, MPRO JP ONLY

38 86266080 1 TERM, 18G .25 FEMALE COUPLER

34

Solution 1

86348550 BRC 30/15 C

3586348550 BRC 30/15 C

Solution 1

REF PART NO. QTY DESCRIPTION SERIAL NO.

FROM NOTES

1 86201110 2 PUMP, 110/120 60 HZ

2 86240520 4 HOSEBARB, 1/8MPT X 1/4 90D

3 86010640 2 WASHER, #10 LOCK EXT STAR

4 86006770 2 SCR, 10-32 X 1/4 PHTR PLTD

5 86215450 1 BOX, PUMP MOUNT

6 86304750 1 SHEILD, PUMP ENCLOSURE

36

Solution 2

86348550 BRC 30/15 C

3786348550 BRC 30/15 C

Solution 2

SEE HOSE DIAGRAM FOR HOSE ROUTING.

REF PART NO. QTY DESCRIPTION SERIAL NO.

FROM NOTES

1 86219580 1 JET, RT ANG, 1/4 BARB

2 86216810 1 CLIP, SHAFT, 9-12MM

3 86219200 1 HOSEBARB, 3/8MPT, 2 X 1/4. 1 X 3/8

4 86172950 4 SCR, M5X12, SHCS, ISO4762, SS

5 86233150 3 CLAMP, 3/8 HOSE (D-SLOT)

6 86219090 1 HOSE, 3/8" X 432MM CLEAR

7 86200820 1 NIPPLE, 1/8FPT QD MALE BRASS

8 86219070 1 HOSE ASM, 6MM X 610MM NYLOBRAID

9 86377730 1 HOSE, 6MM X 190MM NYLOBRAID **

10 86233090 6 CLAMP, 1/4 ID HOSE

11 86289330 1 HOSEBARB, TEE 3/8 X 3/8 X 1/4

12 86219050 1 HOSE, 6MM X 390MM NYLOBRAID

13 86240430 1 HOSEBARB, 3/8 MPT X 3/8 NYLON

14 86012680 1 HOSE, 3/8ID X 60MM NYLOBRAID

15 86005640 1 NUT, 10-32 NYLOCK

16 86010640 1 WASHER, #10 LOCK EXT STAR SS

17 86219060 1 HOSE, 6MM X 420MM NYLOBRAID

18 86291670 1 COVER, PUMP BOX

19 86310300 1 ASSY, ADPT, 1/8MX1/4FPT NIPPLE

20 86377740 1 HOSE, 6MM X 40MM NYLOBRAID **

21 86349410 1 CHECK VALVE, MINI **

22 86219080 1 HOSE, 6MM X 245MM NYLOBRAID

38

Tank & Dome

86348550 BRC 30/15 C

3986348550 BRC 30/15 C

Tank & Dome

REF PART NO. QTY DESCRIPTION SERIAL NO.

FROM NOTES

1 86347110 1 TANK, SOL, GRY BRC 30/15 C

2 86002390 2 CLAMP, 1.75" WORM GEAR X .312

3 86011910 2 HOSE ASM, 1.5X34" VAC W/ELBOW

4 86291230 1 GASKET, DOME, MINI PRO

5 86217700 1 DOME

6 86291170 1 DOME, PLATE INTERIOR

7 86291190 1 SCREEN, VACUUM INTAKE

8 86007970 1 STRAINER, 3/8 IN. NPT 60 MESH

9 86172940 6 SCR, KA40X10,PT OVAL, WN1412,PL

10 86224960 1 STRAINER, BASKET

11 86172990 4 SCR, M6X12 BHCS, ISO7380, SS

12 86218530 1 HANDLE, RECOVERY TANK

13 86297980 1 TANK, RECOVERY MPRO BLK

14 86216770 1 CLAMP, DOME

15 86215970 2 BRKT, DOME CLAMP

16 86173350 4 WASHER, M5, FLAT, ISO7089, SS

17 86291180 1 DUCT, VACUUM INTAKE

18 86291210 1 O-RING, 26MM ID X 2MM THICK

19 86173000 2 SCR, KA40X20, PT OVAL, WN1412,PL

20 86291220 2 SCR, KA40X16, PT, WN1413, SS

21 86292450 1 GASKET, DUCT

40

Vacuum

3

4

2

3

5

8

6

1

7

(GROUND WIRE)

86348550 BRC 30/15 C

4186348550 BRC 30/15 C

Vacuum

REF PART NO. QTY DESCRIPTION SERIAL NO.

FROM NOTES

1 86173000 3 SCR, KA40x20, PT OHS, WN1412, PLTD

2 86225480 1 VAC MOTOR, 120V 5.7 3ST W/TUBE

3 86173220 4 SCREW, M6-1 X 12 FLGHBTNHMS SS

4 86217420 1 COVER, VAC MOTOR

5 86217370 1 COVER, LOWER BACK

6 86006770 1 SCR, 10-32 X 1/4 PHTR PLTD

7 86010640 1 WASHER, #10 LOCK EXT STAR

8 86291680 1 GASKET, VAC MOTOR

42

Wiring Diagram - Control Panel

BLK

PEM STUD

MODE SWITCH

HANDLE MICRO SWITCH

C

N C

N O

BLK BLU

1.5A BREAKER BRUSH MOTOR

11A BREAKER VAC MOTOR

BLKBLK

3 CONDUCTOR 18 GUAGE

BLACK SHEATH

6 CONDUCTOR 14/16 GUAGE

BLACK SHEATH

FORWARD = ACCESSORY TOOL CENTER = OFF BACK = EXTRACT

GRN

YEL

RED

GRN

WHT

TOP OF MACHINE

GROUND SCREW

"BACK POSTION"

"FORWARD POSITION"

BLK

3 2 1

456

BLK

P/N 880464

BLK

RED

RED

BRN

GRN

WHT

BLK

BLU

3 CONDUCTOR 12 GUAGE

YELLOW SHEATH

YEL

RED

YEL

FRONT OF CONSOLE

GRN

CONNECTOR

MODE SWITCH

1

2

3

4

86348550 BRC 30/15 C

43

Wiring Diagram - Control Panel

REF PARTNO. QTY DESCRIPTION SERIAL

NO.FROM NOTES

1 86218840 1 HARNESS, MAIN

2 86226230 1 WIRE ASM, CONTROL PANEL JUMPER

3 86218830 1 HARNESS, HANDLE

4 86226250 1 WIRE, 14" BLACK/14 76010

86348550 BRC 30/15 C

44

Wiring Diagram - Vacuum, Brush Motor & Pump

BLK

WHT

GRN

BRN

RED

WHT

BLU

BLK

GRN

GRN

GRN

CONNECTOR

G R N

GRN

G R N

GRN

GRN

DASH LINE = PUMP BOX OUTLINE

PUMP ACC

PUMP MAIN

GRN

GRN

GRN

BACK COVER

VAC MOTOR

BRUSH MOTOR

1

1

4

3

2

WHT

WHT

BLK

WHT

BRN

WHT

RED

BLK

WHT

FULL BRIDGE RECT

PEM STUD

BOTTOM OF MACHINE

BLU

86348550 BRC 30/15 C

4586348550 BRC 30/15 C

Wiring Diagram - Vacuum, Brush Motor & Pump

REF PART NO. QTY DESCRIPTION SERIAL NO.

FROM NOTES

1 86226250 3 WIRE, 14" GRN/14 76008 X 76008

2 86223460 1 RECTIFIER, 50A 1000V BRIDGE

3 86303670 1 WIRE ASM, 18 GA GRN 76008/76040

4 86303680 1 WIRE ASM, 18 GA GRN 76008/76042

46

Hose Diagram

(86240430)

(86219050) (PRV 39724)

(86219090) (PRV 39728)

(PRV 40114)

(86012680)

(86219090) (PRV 39725)

(86219080) (PRV 39727)

(86219070)

TO SOLUTION TANK

ACCESSORY PUMP

MAIN PUMP

ACCESSORY TOOL

JET

TO SOLUITON TANK

(PRV 44106) (86240520)

(PRV 40062)

(PRV 40083)

(PRV 40097) 4X

(86200820) (PRV 270-11A)

(PRV 39726)

(86219580)

(86289330) (86219200)

86348550 BRC 30/15 C

4786348550 BRC 30/15 C

Suggested Spare Parts

Accessories

PART NO. DESCRIPTION SERIAL

NO. FROM NOTES

86216430 BUSHING, BRUSH PRESSURE

86229010 BEARING, BRUSH

86216040 BRUSH, CHEVRON, 10 IN

86223350 PULLEY, MOTOR

86223300 PULLEY, BRUSH

86215260 BELT, HTD 5MM 69T 9 WIDE

86247110 MOTOR, 115V BRUSH DRIVE

86217390 COVER, BELT GUARD

86218090 GASKET, VAC SHOE

86219580 JET, RT ANG, 1/4 BARB

86201110 PUMP, 110/120 60HZ FLOJET

86224960 STRAINER, RECT, 80 MESH SS

86225480 VAC MOTOR, 120V 5.7 3ST W/TUBE

86135320 BRUSH SET, 120V VAC

86291230 GASKET, DOME

86291190 SCREEN, DOME VAC INTAKE

86291460 BREAKER, 11A VDE CIRCUIT

86230140 BREAKER, 1.5A CIRCUIT

86002010 BOOT, 3/8 CIRCUIT BREAKER

86007200 SWITCH, DPDT3-POSITION ROCKER

PART NO. DESCRIPTION

86218790 HANDTOOL W/1/8 FEM QD (INCLUDES HOSE ASM)

86290360 HANDTOOL KIT (INCLUDES HOSE ASM AND CARRY BAG)

48

Serial Number

REF. NO.

MODEL: SERIAL #

1 **

86348550 BRC 30/15 C

49

Notes

86348550 BRC 30/15 C

Rate your product and tell us your opinion.

valuer votre produit et dites-nous votre opinion.

www.kaercher.com/welcome

www.kaercher.com/dealersearch

Alfred Krcher SE & Co. KG Alfred-Krcher-Str. 28-40 71364 Winnenden (Germany) Tel.: +49 7195 14-0 Fax: +49 7195 14-2212

DANKE! THANK YOU! MERCI! GRACIAS!

!

Registrieren

Manualsnet FAQs

If you want to find out how the BRC 30 15 C Karcher works, you can view and download the Karcher BRC 30 15 C 1.008-058.0 Operator's Manual on the Manualsnet website.

Yes, we have the Operator's Manual for Karcher BRC 30 15 C as well as other Karcher manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operator's Manual should include all the details that are needed to use a Karcher BRC 30 15 C. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Karcher BRC 30 15 C 1.008-058.0 Operator's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Karcher BRC 30 15 C 1.008-058.0 Operator's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Karcher BRC 30 15 C 1.008-058.0 Operator's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Karcher BRC 30 15 C 1.008-058.0 Operator's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Karcher BRC 30 15 C 1.008-058.0 Operator's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.