Janome 1600P Series Instruction Book PDF

1 of 23
1 of 23

Summary of Content for Janome 1600P Series Instruction Book PDF

WARNING To reduce the risk of burns, fire, electric shock or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children.

2. Use this appliance only for its intended use as described in this instruction book.

Use only attachments recommended by the manufacturer as contained in this instruction book.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or

damaged, or dropped into water.

Return this sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or

mechanical adjustment.

4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing machine and foot

controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, turn all controls to the off (O) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14. Switch this sewing machine off (O) when making any adjustment in the needle area, such as threading the needle,

changing the needle, threading the bobbin, changing the presser foot, and the like.

15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or when making any

other adjustments mentioned in this instruction book.

SAVE THESE INSTRUCTIONS Designs and specifications are subject to change without prior notice.

DANGER To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the electric

outlet immediately after using and before cleaning.

2. Always unplug before replacing a sewing machine bulb. Replace bulb with same type rated 12 V, 5 Watts.

IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following:

Read all instructions before using this appliance.

1

TABLE OF CONTENTS

KNOW YOUR MACHINE Name of Parts ............................................................................................................................... 2 Standard Accessories ................................................................................................................... 3 To Attach Knee Lifter ..................................................................................................................... 3

GETTING READY TO SEW Connecting Machine to Power Supply .......................................................................................... 4 Controlling Sewing Speed ............................................................................................................. 4 Up/Down Needle Position Button .................................................................................................. 5 Bobbin Winding Button .................................................................................................................. 5 Thread Cutter Button..................................................................................................................... 5 Stitch Length Adjustment Dial ....................................................................................................... 5 Reverse Stitch Lever ..................................................................................................................... 5 Presser Foot Lifter ......................................................................................................................... 6 Foot Pressure Dial......................................................................................................................... 6 Attaching and Detaching Presser Foot ......................................................................................... 6 To Remove Bobbin Case and Bobbin ........................................................................................... 7 Setting the Spool of Thread........................................................................................................... 7 Winding a Bobbin .......................................................................................................................... 8 Inserting a Bobbin ......................................................................................................................... 9 Inserting the Bobbin Case into the Hook ...................................................................................... 9 Threading the Needle Thread ..................................................................................................... 10 Built-in Needle Threader ............................................................................................................. 11 Drawing up the Bobbin Thread .................................................................................................... 12 Changing the Needle for Model 1600P ....................................................................................... 13 Changing the Needle for Model 1600P-DB and 1600P-DBX ...................................................... 14 Balancing Needle Thread Tension............................................................................................... 15 Adjusting Bobbin Thread Tension ................................................................................................ 15 Adjusting Needle Thread Tension................................................................................................ 15

HOW TO SEW Test Stitching ............................................................................................................................... 16 Securing a Seam......................................................................................................................... 17 Turning a Square Corner ............................................................................................................. 18 Using the Cloth Guide ................................................................................................................. 18 Rolled Hem ................................................................................................................................. 18

CARE & MAINTENANCE Cleaning the Hook and Feed Dog ............................................................................................... 19 Oiling the Machine ...................................................................................................................... 19 Replacing the Light Bulb ............................................................................................................. 20 Replacing the Light Bulb on the Underside of the Sewing Arm .................................................. 20 Troubleshooting ........................................................................................................................... 21

2

#5

#6

q

w

e

r

t

y

u

i

o

!0

!2!3

!4

!5

!6

!7

!8

!9

@0

!1

Name of Parts q Foot pressure dial w Thread guide e Retractable thread guide r Bobbin winder spindle t Bobbin winder stopper y Speed control slider u Stitch length display i * Thread cutter button o Reverse stitch lever !0 Bobbin winding button !1 Up/Down needle button !2 Knee lifter socket !3 Thread tension dial !4 Hook cover !5 Hook cover plate !6 Needle plate !7 Thread cutter !8 Face cover !9 Foot pressure indicator @0 Thread take-up lever @1 ** Needle threader @2 Needle clamp screw @3 Needle @4 Screw holes for attachments @5 Presser foot @6 Feed dog @7 Setscrew @8 Carrying handle @9 Presser foot lifter #0 Spool pins #1 Machine sockets #2 Power switch #3 Stitch length adjustment dial #4 Handwheel #5 Foot control #6 Power supply cord

@1

@2

@4

@5

@6

@3 @7

@8

@9

#0

#1

#2

#3

#4

KNOW YOUR MACHINE

* Model 1600P and 1600-DBX only ** Model 1600P only

3

Bobbin

Lint brush Hemmer foot Spool cap Net Spool holder

Large screwdriver

Small screwdriver

Cloth guide

Accessory box Oil Knee lifter Instruction book

To Attach Knee Lifter The knee lifter is extremely helpful when sewing applique, patchwork and quilting since it allows you to handle the fabric while your knee controls the presser foot.

Match the ribs on the knee lifter with the notches in the knee lifter socket and insert the knee lifter. q Knee lifter w Ribs e Notches

Push the knee lifter with your knee to raise and lower the presser foot.

NOTE: Do not touch the knee lifter while sewing, otherwise the fabric will not be fed smoothly.

q

we

Standard Accessories

Model 1600P Models: 1600P-DB 1600P-DBX DB x 1 14 ..2 DB x 1 11 ..3

HL x 5 16 ...1 HL x 5 14 ...1 HL x 5 11 ...2 HL x 5 9 ..... 1

Needles

4

Connecting Machine to Power Supply

i

w

q

t

y

r

e

u

q Machine plug w Machine socket for power supply plug e Power supply plug r Outlet t Machine socket for foot control y Foot control plug u Foot control

Turn off the power switch. Insert the foot control plug y into the machine socket t. Insert the machine plug q into the machine socket w. Insert the power supply plug e into the wall outlet r. Turn on the power switch i.

CAUTION Always turn the power switch off and unplug the sewing machine from the electrical outlet when the machine is not in use.

Operating Instructions: The symbol "O" on a switch indicates the "off" position of a switch. For appliances with a polarized plug (one blade wider than the other): To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If it does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way. * Foot control model TJC-005 is used with sewing machine model 1600P.

Speed control slider Sewing speed can be varied with the speed control slider according to your sewing needs. To increase sewing speed, slide it to the right. To decrease sewing speed, slide it to the left.

Foot control Sewing speed is varied by the foot control. The harder you press down on the foot control, the faster the machine runs.

The machine runs at the maximum speed set by the speed control slider when the foot control is being fully depressed.

Controlling Sewing Speed

GETTING READY TO SEW

5

Up/Down Needle Position Button

3

RED LED GREEN LED Press this button to bring the needle bar up or down. The RED LED will light up when the needle is down. The GREEN LED will light up when the needle is up. The machine will stop with the needle up or down depending on the needle position determined by this button. The machine will always stop with the needle up after auto thread cutting or buttonhole sewing.

Press this button to wind the bobbin. The LED will light up when you shift the bobbin winding stopper toward the bobbin and press this button. The LED signal will turn off after bobbin winding is finished.

LED

Bobbin Winding Button

Thread Cutter Button *Model 1600P and 1600-DBX only Pressing this button after sewing will trim the

threads. You can continue sewing without pulling the bobbin thread up after trimming the threads.

* Use the thread cutter on the face cover if the thread is thicker than #30.

* The foot control and Up/down needle position button cannot be used while the machine is trimming the threads.

Stitch Length Adjustment Dial

You can adjust the stitch length from 0 to 6 mm by turning this dial. The stitch length will be show on the stitch length display q.

Reverse Stitch Lever

The machine will sew in reverse while the reverse stitch lever is pressed down. The machine will sew forward if the lever is released. Use the lever to lock the beginning and end of seams.

q

6

2 1 0

3 4 5

q Presser foot lifter w Normal up position e Highest position

The presser foot lifter q raises and lowers the presser foot. You can raise it higher e than the normal up position w to help you place thick material under the foot.

w

e

q

Presser Foot Lifter

Foot Pressure Dial

q Foot pressure dial w Setting indicator

The foot pressure control dial should be set at 3 for regular sewing. Reduce the pressure for appliqu, sewing on fine synthetics and elastic fabrics. Set the dial at 1 when sewing extra fine fabrics.

NOTE: Do not reduce the foot pressure lower than 0.

q q

q Setscrew

To change the presser foot, raise the presser foot lifter.

Loosen the setscrew q, choose the proper foot and insert it from the bottom.

Tighten the setscrew q with the large screwdriver to secure the foot.

Attaching and Detaching Presser Foot

q

w

7

To Remove Bobbin Case and Bobbin

q Hook cover plate w Hook cover e Latch r Bobbin case t Bobbin z Raise the needle and presser foot.

Remove the hook cover plate q and open the hook cover w.

x Pull open the latch e of the bobbin case r. Take the bobbin case straight out of the hook.

To remove the bobbin from the bobbin case: Release the latch, then drop the bobbin t out of the bobbin case as illustrated. * Only use this exclusive bobbin for model 1600P.

CAUTION Turn the power switch off and unplug the sewing machine from the electrical outlet

t

Setting the Spool of Thread

q Spool of thread w Spool pin e Spool cap

Setting a spool of thread: Place a spool of thread q on the spool pin w with the thread coming off the spool as shown. Attach the spool cap e, and press it firmly against the spool of thread.

r Spool holder t Net

Setting the thread cone: Place the spool holder r on the spool pin, then place the thread cone on the spool holder. Cover the thread cone with the net t if the spool thread is shaky when sewing.

e

q

w

r

t

q

w

z

r

r

x e

8

Winding a Bobbin

q Thread guide bar w Bobbin winding tension disk e Bobbin hole r Notch t Spring y Bobbin winder spindle u Bobbin winder stopper

z Pass the thread through the guide on the thread guide bar q from behind.

x Pass the thread under the bobbin winding tension disk w.

c Thread through the hole e in the bobbin from the inside to the outside. Match the notch r with the spring t on the bobbin winder spindle. Then insert the bobbin on the bobbin winder spindle y.

v Push the bobbin winder stopper to the left u.

b Hold the free end of the thread in your hand and press the bobbin winding button i. Press the bobbin winding button again to stop the bobbin when it has made several turns, and cut the thread close to the hole in the bobbin.

n Press the bobbin winding button again. When the bobbin is fully wound, the machine will stop automatically. Return the bobbin winder stopper to its original position. Cut the thread with a scissors. Remove the bobbin from the bobbin winder spindle.

z x

c

v

b

n

NOTE: This machine has an exclusive motor for bobbin winding, which allows you to wind a bobbin while stitching.

q

w

e

r

t

y

u

i

Pull the thread guide bar up as far as it will go. Turn the thread guide bar until the stoppers click into position.

Stopper

9

z Place a bobbin in the bobbin case making sure the thread winds clockwise on the bobbin as illustrated.

x Draw the thread through the slit q of the bobbin case. q slit

c Continue to draw the thread under the tension spring w and through the opening e. Pull out about 4 (10 cm) of thread. The bobbin should spin clockwise when the thread is pulled out of the bobbin case. w Tension spring e Opening

1

2

3

Inserting a Bobbin

q

w

e

Inserting the Bobbin Case into the Hook

z Holding the latch q open, position the bobbin case into the hook aligning the slot w with the rib e.

The bobbin case should lock into place when the latch is released. q Latch w Slot e Rib

x Close the hook cover r and attach the hook cover plate t in this order. r Hook cover t Hook cover plate

z

x

c

z

x

q

w

e

r

t

10

* Use only left twist thread

z Raise the presser foot lifter. Press the Up/Down needle button twice to raise the needle to its highest position. Turn the power switch off. Set a spool of thread on the spool pin. Pass the thread through the guide on the thread guide bar q from the behind.

x Pass the thread through the thread guide plate w, then draw the thread between the pre-tenison disks e under the pre-tension dial r. * If the thread flutters around while sewing,

pass the thread through three holes in the guide plate as illustrated in fig.(A).

* The standard setting of the pre-tension dial is that the screw head t sinks about 4 mm (1/8 to 3/16) y.

c Holding the thread with both hands, draw the thread down and around the tension dial u from right to left. Pull the thread up to insert it between the tension disks o and pass it over the tail of the check spring. Then pull the thread down over the loop of the check spring i.

v Draw the thread through the thread guide !0, !1 and eye of the thread take-up lever !2. Pass the thread through the thread guide !1 again. Holding the thread with both hands, slip the thread into the thread guide !3 as shown.

b Draw the thread down to the needle bar thread guide !4, then pass the thread through the needle !5. For model 1600P, use the built-in needle threader (see page 11).

Threading the Needle Thread

c

!0

!1

!2

!3

o

u

u

i

i

x y

t

b

v

u

!0

!1

!3

!4

!5

w

e

r

!2

(A) x

z

q

!4

!5

11

z Lower the presser foot. Press the Up/Down needle button twice to raise the needle to its highest position. Turn the power switch off. Push down the needle threader knob q as far as it will go.

Built-in Needle Threader *Model 1600P only

z

r

w

e

q

x

c

v

b

x Turn the knob q in the direction of the arrow to insert the hook into the needle eye. The hook r comes out through the needle eye as illustrated.

c Holding the thread with both hands, draw the thread along the thread path w. Then hook the thread around the guide e.

v Draw the thread under the hook r. Hold the end of thread with your hand while pulling up the thread lightly in the direction of arrow.

b Turn the knob in the direction of the arrow as shown, drawing the thread loop t through the needle. Release the threader knob slowly. Then pull the thread loop t to the right.

t

The needle threader may not work well with these combinations.

#9 #20, #30, #50, #60

Needle

#11 #20, #30

#14 #16, #20, #30

12

z Hold the needle thread q lightly with your left hand.

x Turn the switch on. Press the Up/Down needle position button twice to pick up the bobbin thread w. Pull the needle thread q to bring up a loop of bobbin thread w.

c Slide 10 cm (4) of both threads to the rear under the presser foot.

z

x

Drawing up the Bobbin Thread

q

q

w

c

13

w e e

z Turn the power switch off. Lower the presser foot. Turn the needle clamp screw q counterclockwise with the large screwdriver. Loosen the screw and remove the needle from the needle clamp. q Needle clamp screw

To determine if the needle is defective, place the flat side of needle on something flat (a needle plate, piece of glass, etc.). The gap between the needle and the flat surface should be consistent.

Never use a blunt or blunt needle, as it may cause skipped stitches or thread breakage. Defective needles can ruin the fabric. Always purchase good quality needles. Change needles often.

Needle (HL x 5) size

9 or 11

11 or 14

14, 16 or 18

Light weight

Medium weight

Heavy weight

Fabrics Crepe de chine, Voile, Lawn, Organdy, Georgette, Tricot

Linens, Cotton, Pique, Serge, Double Knits, Percale

Denim, Tweed, Gabardine, Coating, Drapery and Upholstery Fabric

Thread Fine silk Fine Cotton Fine Synthetic Covered Polyester

50 silk 50 to 80 Cotton 50 to 60 Synthetic Cotton Covered Polyester

50 silk 40 to 50 Cotton 40 to 50 Synthetic Cotton Covered Polyester

Thread and Needle Chart

z

x

q

x Insert a new needle into the needle clamp w with the flat side e to the right, pushing it up as far as it will go. Tighten the clamp screw q firmly. w Needle clamp e Flat side

* Use an HL x 5 needle

Changing the Needle for Model 1600P

CAUTION Turn the power switch off and unplug the machine before changing the needle.

To Check the Needle

14

z Turn the power switch off. Lower the presser foot. Turn the needle clamp screw q counterclockwise with the large screwdriver. Loosen the screw and remove the needle from the needle clamp. q Needle clamp screw

To determine if the needle is defective, place the needle on something flat (a needle plate, piece of glass, etc.). The gap between the needle and the flat surface should be consistent.

Never use a blunt or blunt needle, as it may cause skipped stitches or thread breakage. Defective needles can ruin the fabric. Always purchase good quality needles. Change needles often.

Needle (DB x 1) size

9 or 11

11 or 14

14, 16 or 18

Light weight

Medium weight

Heavy weight

Fabrics Crepe de chine, Voile, Lawn, Organdy, Georgette, Tricot

Linens, Cotton, Pique, Serge, Double Knits, Percale

Denim, Tweed, Gabardine, Coating, Drapery and Upholstery Fabric

Thread Fine silk Fine Cotton Fine Synthetic Covered Polyester

50 silk 50 to 80 Cotton 50 to 60 Synthetic Cotton Covered Polyester

50 silk 40 to 50 Cotton 40 to 50 Synthetic Cotton Covered Polyester

Thread and Needle Chart

z

x

q

x Insert a new needle into the needle clamp w with the groove e to the left, and the small scarf r back on the needle to the right. Push the needle up as far as it will go. Tighten the clamp screw q firmly. w Needle clamp e Groove r Scarf

* Use a DB x 1 needle

Changing the Needle for Model 1600P-DB and 1600P-DBX

CAUTION Turn the power switch off and unplug the machine before changing the needle.

To Check the Needle

e e

r r

Front Right Back

w

qNeedle

15

The needle thread and bobbin thread should interlock in the center of two layers of the fabric in straight seams.

Test the bobbin thread tension by holding the end of the bobbin thread and suspending the bobbin case as illustrated. Then jerk the bobbin case once by flicking your wrist.

If the thread comes out of the bobbin case continuously, and the bobbin case keeps falling, the bobbin thread tension is too loose. Make a slight adjustment by turning the screw clockwise with the small screwdriver. q To tighten

If the thread does not come out of the bobbin case at all, the bobbin thread tension is too tight. Make a slight adjustment by turning the screw counterclockwise with the small screwdriver. w To loosen

q

w

Needle thread tension is too tight: If the bobbin thread r shows through on the right side of the fabric q and it feels bumpy, loosen the needle thread tension by turning the dial to the left.

q Right side of the fabric w Wrong side of the fabric e Needle thread r Bobbin thread

Needle thread tension is too loose: If the needle thread e loops on the wrong side of the fabric w, tighten the needle thread tension by turning the dial to the right.

q

q

w

w

e

r

Balancing Needle Thread Tension

Adjusting Bobbin Thread Tension

Adjusting Needle Thread Tension

16

Before you start sewing your garment, try test stitching with the same thread and fabric as your garment.

z Turn the stitch length adjustment dial q to adjust the stitch length. Slide the needle and bobbin threads to the back under the presser foot. Use the same fabric for actual sewing.

x Turn the handwheel w toward you to lower the needle into the fabric.

c Set the speed control slider to (slow) until you get used to the sewing speed. Lower the presser foot lifter e. Press the foot control r to start sewing.

z

x

c

v

b

Thread take-up lever

NOTE: Raise the thread take-up lever to its highest position, otherwise the needle thread may slip out from the needle eye.

Test Stitching

w

e

r

t

y

u

q

HOW TO SEW

v Check the sewing result and adjust the needle thread tension t as necessary.

b Press the auto thread cutter button y to trim the threads for model 1600P and 1600P-DBX. You can continue sewing without pulling the bobbin thread up to the needle plate after trimming the threads.

* Use the thread cutter u on the face cover if: the sewing machine is model 1600P-DB. the thread is thicker than #30.

17

1cm (3/8)

1cm (3/8)

The machine will sew in reverse as long as the reverse stitch lever is pressed. Secure the beginning and end of a seam by sewing in reverse for about 1 cm (3/8).

Pull the bobbin thread to bring the needle thread to the wrong side of fabric. Tie the threads together. Trim the remaining threads.

Stop the machine a few stitches before the end of the seam. Press the up/down needle button a few times until the needle falls on the end of the seam.

Raise the presser foot.

Pivot the fabric around the needle to change the sewing direction. Lower the presser foot and start sewing in a new direction.

By knotting the threads

Turning a Square Corner

By reverse stitching Securing a Seam

18

Attach the cloth guide to the needle plate with the screw q. Adjust the position of the cloth guide w and tighten the screw q.

Attach the hemmer foot w to the presser foot bar. Tighten the setscrew q using the large screw- driver. q Setscrew w Rolled hem

Fold the edge of the fabric twice, 6 cm (2 3/8) in length and 0.3 cm (1/8) in width. Trim the corner 0.5 cm (3/16) r by 0.8 cm (1/4) t for easier insertion of the hem into the foot.

e Wrong side of the fabric r 0.5 cm (3/16) t 0.8 cm (1/4) y Curl of the foot

Position the fabric aligning the edge of hem with the curl of the foot y. Lower the foot and sew 12 cm (1/21) while pulling both threads to the back. Stop the machine and lower the needle into the fabric. Raise the foot and insert the folded portion of the fabric into the curl of the foot.

Lower the foot, and then sew while lifting up the edge of the fabric to keep it feeding smoothly and evenly.

r

t

y

e

e

q

w

Using the Cloth Guide

q w

e

Rolled Hem

Place the fabric with its edge e against the cloth guide and sew.

19

z Remove the needle and presser foot. x Remove the hook cover plate q and open the

hook cover w. c Loosen the setscrew e and remove the needle plate r. v Clean the hook t and feed dog y with a lint brush u. b After cleaning the machine, attach the needle plate r,

needle and presser foot. q Hook cover plate w Hook cover e Setscrew r Needle plate t Hook y Feed dog u Lint brush

CAUTION: Turn the power switch off and unplug the machine before cleaning.

Cleaning the Hook and Feed Dog

Oiling the Machine

NOTE: Unplug the machine before oiling.

Oil the points as shown (q, w and e) with two or three drops of oil. Use only sewing machine oil MO-70 for this sewing machine. Oil the machine once a day if you use the machine frequently.

Use a soft, dry cloth to remove excess oil. Remove the bobbin case from the hook when you oil the hook race. After oiling, stitch a piece of waste fabric to absorb excess oil.

r e

q

w

u

y

t

q

w

e

CARE & MAINTENANCE

20

Replacing the Light Bulb

q

w

e

r

CAUTION: Turn the power off before replacing the light bulb. The bulb could be HOT, wait until it has cooled down before touching it.

q Setscrew w Face cover e Lamp socket r Light bulb

To remove: Remove the setscrew q. Remove the face cover w. Pull out the bulb r from the lamp socket e.

To replace: Insert a new bulb into the opening of the socket e. Attach the face cover w with the setscrew and cap.

Replace the bulb with the same type, rated 12 V, 5 W.

q

e

w

q

Lay the machine on its back.

Replacing the Light Bulb on the Underside of the Sewing Arm

Detach the lamp window q from the machine with the screw driver as shown. Pull out the light bulb e from the socket.

Insert a new bulb into the socket w. Attach the lamp window q into the opening on the machine. q Lamp window w Lamp socket e Light bulb

Replace the bulb with the same type, rated 12 V, 5 W.

21

See page 10

See page 15

See pages 13, 14 See pages 13, 14

See page 12 See pages 11, 13, 14

See page 9

See page 19

Replace the bobbin.

See pages 13, 14

See pages 13, 14 See pages 13, 14

See pages 13, 14

See pages 11, 13, 14

See page 13

See page 10 Change the needle.

See page 15

See page 10

See pages 11, 13, 14 Make the stitch shorter

See page 19 Make the stitch longer

See page 15 See pages 11, 13, 14

See page 4 See page 19

See page 19 See page 19

See page 19

1. The needle thread is not threaded properly.

2. The needle thread tension is too tight.

3. The needle is bent or blunt. 4. The needle is incorrectly inserted.

5. The needle thread and the bobbin thread are not set under the

presser foot when starting sewing. 6. The thread is either too heavy or too fine for the needle.

1. The bobbin thread is not threaded properly in the bobbin holder.

2. Lint has collected in the hook race.

3. The bobbin is damaged and doesn't turn smoothly.

1. The needle is incorrectly inserted.

2. The needle clamp screw is loose. 3. The needle is too fine for the fabric being used.

1. The needle is incorrectly inserted, bent or blunt.

2. The needle and/or fabrics are not suitable for the work being

sewn. 3. A Blue Tip needle is not used when sewing stretch, very fine

fabrics and synthetics.

4. The needle thread is not threaded properly. 5. A poor quality needle is being used.

1. The needle thread tension is too tight.

2. The needle thread is not threaded properly.

3. The needle is too heavy for the fabric being sewn. 4. The stitch length is too long for the fabric.

1. The feed dog is packed with lint. 2. The stitches are too fine.

1. The needle thread tension is too loose. 2. The needle is either too heavy or too fine for the thread.

1. The machine is not plugged in. 2. Thread has been caught in the hook race.

1. Thread has been caught in the hook race. 2. Lint has built up in the hook race or bobbin holder.

3. The machine needs oiling.

Troubleshooting Condition The needle thread

breaks.

The bobbin thread

breaks.

The needle break

Manualsnet FAQs

If you want to find out how the 1600P Series Janome works, you can view and download the Janome 1600P Series Instruction Book on the Manualsnet website.

Yes, we have the Instruction Book for Janome 1600P Series as well as other Janome manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Book should include all the details that are needed to use a Janome 1600P Series. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Janome 1600P Series Instruction Book is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Janome 1600P Series Instruction Book consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Janome 1600P Series Instruction Book free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Janome 1600P Series Instruction Book, simply download the document to your computer. Once downloaded, open the PDF file and print the Janome 1600P Series Instruction Book as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.