Hoover PRP2400 001 User Manual PDF

1 of 10
1 of 10

Summary of Content for Hoover PRP2400 001 User Manual PDF

C

M

Y

CM

MY

CY

CMY

K

1 -

Parts Description

1 Cord Storage

2 Tank

3 Rear Rubber

4 Iron Tray

5 Rubber Studs

6 Iron Lock System

7 Water Tank Cap

8 Steam Hose Storage

9 Decoration Cover

10 Iron Light

11 Steam Trigger

12 Temperature Dial

13 Main Switch

14 Water Tank Empty Light

15 Steam Boost Switch

3

4 5

2

1

11

6

7

8

10

12

9

15 14 13

Fig. 1: Base and Tank Description

Fig. 2: Domestic Iron Description

Fig. 3: Domestic Iron Control Panel

2

Introduction Dear customer,

First of all, we would like to congratulate you for purchasing this Hoover ironing system and to thank you for the confidence you have in Hoover brand.

This appliance has been manufactured with great care, respecting all of our quality criteria and has been tested several times. We hope its use will fulfil your expectations. We are strongly convinced that it will make your ironing much faster and better.

Before using your new Hoover appliance, please read carefully this users manual. If you need further information or if you encounter any trouble which are not noted in this manual, please contact the after-sales service or your standard dealer.

Important Safety Instructions

Read this user manual carefully before you first use and save it for future reference.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. This product has been designed for domestic use only. In case of any commercial use, inappropriate use or failure to comply with the instructions, the manufacturer is not responsible and the guarantee will not apply. Before connecting your appliance, check if the mains voltage is the same as the voltage indicated on your appliance and that the power outlet is connected to the earth. Ensure before each use that the electric cord or any other important part is not damaged. Keep the iron and its cord out of reach of children

3

Important Safety Instructions

less than 8 years of age when it is energized or cooling down. Never direct the steam towards persons or animals. Never direct the steam jet towards any other electrical or/and electronic appliances. The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking. If the appliance shows evidence of breakdown, malfunction, leakages. Please make sure it is checked by an authorized Service Centre to avoid any danger. Always make sure the appliance is switched off, unplugged and cooled down before doing any maintenance work. The iron must not be left unattended while it is connected to the supply mains and before it has cooled down. Do not unplug the appliance by pulling on the cord or on the appliance. Never immerse the iron, the stand, the cable or the plugs in water. Never hold them under the water tap. The soleplate of the iron can become extremely hot and may cause burns if touched. Never touch the electric cords with the soleplate. If the supply cord is damaged, it must be replaced by the manufacturer, service agent or similarly qualified persons in order to avoid a hazard.

4

Important Safety Instructions

When placing the iron on its stand, ensure that the surface on which the stand is placed is stable. The plug must be removed from the socket-outlet before the water reservoir is filled with water. The surfaces with are liable to get hot during use. To have a electronic copy of the instruction manual contact the after sales service in guarantee card. The iron must be used and rested on a stable surface.

Chapter 1: Preparation for Use

Chapter 1.1 : What Kind of Water May be Used?

Due to the powerful output of steam, Hoover recommends the use of an active ironing board with blowing and vacuuming function which allows escape of any excess steam.

Place the ironing system on a stable and level surface, for example on the hard part of an ironing board or on a heat-resistant surface.

IMPORTANT: Ensure your appliance is unlocked before switching the power on (Fig 4).

The Hoover ironing system has been designed to be used with tap water only. There is no need to use distilled or pure distilled water. Nevertheless, in case you live in a hard water area, you can mix 50% of distilled water with 50% of tap water. Do not use any other kind of water or do not add other contents to water tank as it can damage your appliance.

Chapter 1.2 : Filling the Water Tank Switch off the appliance and unplug it.

Open the water tank cap (7) to gain access to the water tank.

Fill the tank with Tap water and ensure you do not exceed the MAx mark.

WARNINg: Do not add vinegar, hot water, perfume, or any other kind of chemical agents or any other contents in the water tank. It could damage the steam generator and shorten its life use.

Fig. 5: Water Tank Filling

Fig. 4: Unlock & Switch on Iron System

Connect the appliance with the mains cord to the earthed socket, the light (13) will flash with red meaning that the appliance is in standby status. Press on the switch, the light will turn green meaning that the appliance is switched on. Turn the temperature dial (12) to your desired setting, the iron light (10) illuminates meaning the soleplate is heating up. After approximately 3 minutes , the light (13) will stop flashing and remain constant. You can now start ironing and if you require steam press the steam trigger (11).

Chapter 1.3 - Switching on the Appliance

1 12

3

5

IMPORTANT: 1. The appliance has a Steam Boost Function. If you want to increase the amount of Steam you can press the Steam Boost Button (15), the green light will illuminate , indicating you have actioned this function. 2. When Water tank empty light (14) flashes red, this means there is no more water in the tank. Please refill the tank following the instructions of chapter 1.2.

N.B. The first time the appliance is used, some fumes, dust and a smell can be noted. Its quite normal and will quickly disappear. This is due to a treatment applied to the soleplate that improves the steam performance. Before use, please use the iron as described in Chapter 2.4 Vertical Steam Ironing.

Chapter 2: Using Your Steam Generator

Select the temperature of the soleplate by turning the dial (12) on the iron to the desired position. Wait a few moments until the iron light (10) is off. This indicates that the soleplate has reached the required temperature.

While Ironing , the Iron light may switch on and off, this indicates that the temperature is being Adjusted automatically to maintain temperature so as not to interrup your ironing.

Help To know the best suitable temperature for each textile, check the laundry care label of the article to be ironed. Please note that during use, the temperature light goes on from time to time. It signifies that the iron is heating up to the set temperature. When ironing material with mixed fabrics, always ensure the temperature is set to the correct setting. If you select a lower temperature while ironing, wait until the iron has cooled down to the set temperature before you continue ironing. If the temperature is too low, some drops of water could escape from the soleplate. Please raise up the temperature above the 2 dots () to avoid this issue.

Chapter 2.1: Regulating the Soleplate Temperature

Dry Ironing

Select the temperature of the soleplate following the indications of chapter 2.1. Start your ironing without pressing the steam trigger (11), when the soleplate reaches the appropriate temperature.

Steam Ironing

Select the temperature of the soleplate following the indications of chapter 2.1. The steam will be ready to be used after iron light(10) disappear. From that time you can begin ironing and use the steam trigger. The steam flow stops when you release the trigger.

N.B. During use, it is normal to experience some noise coming from your steam generator. It signifies that a pump injects water into the boiler.

Chapter 2.2 - Ironing

Fig. 6: Pressing Steam Trigger Graphic

6

To obtain the best results, it is really important to set the correct temperature of the soleplate and the steam flow you are using. If correctly used, it will simplify your ironing and provide outstanding results, making ironing easier and faster.

Chapter 2.3 - How to Choose the Correct Soleplate Temperature and Steam?

Textile Soleplate TC Jeans

Cotton

Linen

Starched Clothes

Velvet/Alcantara

Wool

Silk

Cashmere

Rayon

Polyester

Nylon

Acrylic

Lycra

Polyamid

Chapter 2.4 - Vertical Steam Ironing Set the soleplate temperature (12) to the max temperature.

Hang curtains and clothes (jackets, suits, coats). Hold the iron in a vertical position at a short distance from the fabric to avoid burning it. Press the Steam trigger (11) to release the steam and move the Iron top to bottom.

WARNINg: Do not direct the steam jet towards people or animals.

Help

When steam ironing clothes on which shiny patches may occur, we recommend you to set the soleplate temperature to a lower temperature or iron the garment on the reverse.

Start with the fabrics that needed to be ironed at a lower temperature () and finish with those that needed to be ironed at the higher temperature (/Max).

Chapter 2.5 - Refilling the Water Tank During Usage You can fill the water tank at any time during use. When the water tank is empty, the Empty water tank (14) will flash and alarm. No more steam is released from the soleplate. Open the water tank cap (7), Refill the water tank ensuring you do not exceed the Max mark level. Please refer to chapter 1.2 for more detailed instructions.

7

Chapter 3: Maintenance and Cleaning

Chapter 2.6: Auto Shut off Function

All the maintenance and cleaning operations have to be carried out when the unplugged appliance has cooled down for at least 2 hours, to prevent any risk of burns.

The auto shut off function automatically switches off the appliance if the trigger (11) has not been used after 10 minutes. The main switch (13) will beeping and flash with red color to remind you that the appliance start go into standby status, you must switch on the appliance again.

Chapter 3.1 - Cleaning the Appliance Do not use any detergent or descaling products for cleaning the soleplate. Regularly clean it with a humid and non-metallic pad. Empty the water tank after each use before storing it, to empty the water tank, press the trigger to release steam until no steam come out. To clean the plastic parts of the stand, please use soft clothes.

Fig. 7: Domestic Iron Lock System

Fig. 8: Cord Storage

Chapter 3.2: Lock System Switch off the appliance and unplug it.

Empty the water tank, to empty the water tank, press the trigger to release steam until no steam come out.

Put the iron on the heat-resistant iron rubber studs (5). Wait at least 30 minutes allowing the soleplate and the generator to cool down.

Then follow the underneath indications in order to lock correctly your iron.

NOTE:

To lock the iron, you must ensure the soleplate is embedded in the rear rubber (3).

To unlock it, you must press the lock button then recover the hook to normal position.

Chapter 3.4: Cord Storage

Store the power cord with cord storage holder (1), and store the steam hose in the steam hose storage (8).

Then you can take away your appliance in order to store it safely and easily.

1 12

2

1

8

Troubleshooting

Problem Cause Solution The Iron does not heat up.

There is a connection problem.

The appliance is not switched on.

The soleplate temperature is too low.

Check the mains cord, the plug and the wall socket

Press on the on/off switch

Set a higher temperature of the soleplate

The appliance does not produce steam

The appliance is not switched on

The tank may be empty

You are not pressing the steam trigger

The soleplate temperature is set to the maximum

Press on the on/off switch

Refill the water tank

Press the steam trigger

It works but steam is not visible as very hot and dry.

The soleplates becomes dirty or brown

There should be chemical or additives in the water used for ironing

The linen is still dirty

Never use any chemical or additives in the water. Contact your after sales service if the linen is still dirty

Clean the soleplate with a non-metallic sponge

Water stripes appear on the textile

Your ironing board cover is saturated in water

Change the cover or use a mesh ironing board

The empty water tank indicator light flash and alarm

There is

Manualsnet FAQs

If you want to find out how the PRP2400 001 Hoover works, you can view and download the Hoover PRP2400 001 User Manual on the Manualsnet website.

Yes, we have the User Manual for Hoover PRP2400 001 as well as other Hoover manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Hoover PRP2400 001. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Hoover PRP2400 001 User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Hoover PRP2400 001 User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Hoover PRP2400 001 User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Hoover PRP2400 001 User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Hoover PRP2400 001 User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.