Hikvision DS-K3G501SX Turnstile Quick Start Guide PDF

DS-K3G501S Series Tripod Turnstile Quick Start Guide

Legal Information

2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.

About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website ( https:// www.hikvision.com/ ). Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.

Trademarks

and other Hikvision's trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners.

Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED "AS IS" AND "WITH ALL FAULTS AND ERRORS". HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE

DS-K3G501S Series Tripod Turnstile Quick Start Guide

i

DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS.

Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image. As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protection laws and regulations, including without limitation, conducting security controls to safeguard personal data, such as, implementing reasonable administrative and physical security controls, conduct periodic reviews and assessments of the effectiveness of your security controls.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

ii

Regulatory Information

FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed

DS-K3G501S Series Tripod Turnstile Quick Start Guide

iii

under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see:www.recyclethis.info

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

iv

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.

Dangers: Follow these safeguards to prevent serious injury or death.

Cautions: Follow these precautions to prevent potential injury or material damage.

Danger: In the use of the product, you must be in strict compliance with the electrical safety regulations

of the nation and region. The equipment must be connected to an earthed mains socket-outlet. Shock hazard! Disconnect all power sources before maintenance. Do not touch the bare metal contacts of the inlets after the circuit breaker is turned off.

Electricity still exists. indicates hazardous live and the external wiring connected to the terminals requires installation by an instructed person.

Keep body parts away from fan blades. Disconnect the power source during servicing. Keep body parts away from motors. Disconnect the power source during servicing. To prevent possible hearing damage, do not listen at high volume levels for long periods. All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region.

Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.

Please make sure that the power has been disconnected before you wire, install or dismantle the device. If the top caps should be open and the device should be powered on for maintenance, make sure: 1. Power off the fan to prevent the operator from getting injured accidentally. 2. Do not touch bare high-voltage components. 3. Make sure the switchs wiring sequence is correct after maintenance.

Please make sure that the power has been disconnected before you wire, install or dismantle the device.

When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power

cable, and then please contact the service center.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

v

Do not ingest battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Operation of this equipment in a residential environment could cause radio interference. The device do not support the PoE network switch. Connecting with the PoE network switch may

damage the control board.

Cautions: The equipment shall not be exposed to dripping or splashing and that no objects filled with

liquids, such as vases, shall be placed on the equipment. Ensure correct wiring of the terminals for connection to an AC mains supply. The equipment has been designed, when required, modified for connection to an IT power distribution system.

+ identifies the positive terminal(s) of equipment which is used with, or generates direct current. + identifies the negative terminal(s) of equipment which is used with, or generates direct current.

No naked flame sources, such as lighted candles, should be placed on the equipment. This equipment is suitable for mounting on concrete or other non-combustible surface only. Install the equipment according to the instructions in this manual. To prevent injury, this equipment must be securely attached to the floor/wall in accordance with

the installation instructions. The main element of the turnstile is stainless steel, which is rustless (antioxidant) and corrosion

resistant (The anti corrosion ability in the medium of acid, alkali, and salt). In order to keep the stainless steel from being oxidized or corroded, you should clean and care the turnstile surface periodically. The instructions and tips for maintaining the turnstile are as follows: Select different stainless steel types according to the variety of the environments. You can

select 304 stainless steel for common circumstances and 316 stainless steel for the scenarios of seasides and chemical plants.

Keep the device surface clean and dry. Use non-woven cloth and ethyl alcohol to clean the dirt on the device surface. Use sourcing pad (do not use mesh cleaning ball) to clean the rust on the device surface by

following the wire drawing on the stainless steel. And then use non-woven cloth and stainless steel cleaner to wipe the device surface.

Clean and maintain the device by using non-woven cloth and stainless steel cleaner periodically. It is suggest to clean the device every month in common circumstances and every week for severe environments (seaside and chemical plants for instance.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

vi

Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).

Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.

The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or

radiator is forbidden (ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur

otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.

Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.

Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents.

Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.

Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.

Biometric recognition products are not completely applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.

Do not stay in the lane when the device is rebooting. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED

BATTERIES ACCORDING TO THE INSTRUCTIONS. SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY. The instructions shall require connection of the equipment protective earthing conductor to the installation protective earthing conductor.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

vii

Available Models

Product Name Model

Tripod Turnstile DS-K3G501SX

Scan the QR code to get User Manual of Tripod Turnstile. Note that mobile data charges may apply if Wi-Fi is unavailable.

Figure 1-1 QR Code

DS-K3G501S Series Tripod Turnstile Quick Start Guide

viii

Contents Chapter 1 Overview .................................................................................................................... 1

1.1 Introduction ........................................................................................................................... 1

1.2 Main Features ........................................................................................................................ 1

Chapter 2 System Wiring ............................................................................................................ 3

Chapter 3 Installation ................................................................................................................. 5

3.1 Disassemble Pedestals ........................................................................................................... 5

3.2 Install Pedestals ..................................................................................................................... 5

Chapter 4 General Wiring ........................................................................................................... 9

4.1 Components Introduction ...................................................................................................... 9

4.2 Wiring Electric Supply ............................................................................................................ 9

4.3 Terminal Description ............................................................................................................ 10

4.3.1 Access Control Board Terminal and BUS Description .................................................. 10

4.3.2 Access Control Board Serial Port ID Description ......................................................... 15

4.3.3 RS-485 Wiring ............................................................................................................. 17

4.3.4 RS-232 Wiring ............................................................................................................. 18

4.3.5 Wiegand Wiring .......................................................................................................... 19

4.3.6 Barrier Control Wiring ................................................................................................. 19

4.3.7 Alarm Output Wiring ................................................................................................... 21

4.3.8 Exit Button Wiring ....................................................................................................... 22

Chapter 5 Device Settings ......................................................................................................... 23

5.1 Pair Keyfob (Optional) .......................................................................................................... 23

5.2 Initialize Device .................................................................................................................... 24

5.3 Switch to RS-485/RS-232 Mode ........................................................................................... 25

5.4 Alarm Relay Output Mode (NO/NC) .................................................................................... 26

Chapter 6 Activation ................................................................................................................. 27

6.1 Activate via SADP ................................................................................................................. 27

DS-K3G501S Series Tripod Turnstile Quick Start Guide

ix

6.2 Activate Device via iVMS-4200 Client Software ................................................................... 28

Appendix A. Tips for Scanning Fingerprint ................................................................................ 30

Appendix B. DIP Switch ............................................................................................................ 32

B.1 DIP Switch Description ......................................................................................................... 32

B.2 DIP Switch Corresponded Functions .................................................................................... 32

Appendix C. Event and Alarm Type ........................................................................................... 34

Appendix D. Table of Audio Index Related Content ................................................................... 35

Appendix E. Communication Matrix and Device Command ....................................................... 36

DS-K3G501S Series Tripod Turnstile Quick Start Guide

x

Chapter 1 Overview

1.1 Introduction

The tripod turnstile is designed to detect unauthorized entrance or exit. By adopting the turnstile integratedly with the access control system, person should authenticate to pass through the lane via swiping IC or ID card, scanning QR code, etc. It is widely used in attractions, stadiums, construction sites, residences, etc.

1.2 Main Features 32-bit high-speed processor TCP/IP network communication

The communication data is specially encrypted to relieve the concern of privacy leak Remaining open/closed mode selectable Bidirectional (Entering/Exiting) lane

The barrier opening and closing speed can be configured according to the visitor flow

DS-K3G501S Series Tripod Turnstile Quick Start Guide

1

Self-detection, Self-diagnostics, and automatic alarm Remote control and management Online/offline operation LED indicates the entrance/exit and passing status Barrier is in free status when powered down. People can pass through the lane along single/both

singe and double directions Fire alarm passing

When the fire alarm is triggered, the barrier will be dropped down automatically for emergency evacuation

Valid passing duration settings System will cancel the passing permission if a person does not pass through the lane within the valid passing duration

Opens/Closes barrier according to the schedule template Up to 3000 visitor cards and up to 60,000 cards except for visitor cards can be added Up to 180,000 presenting card events can be recorded Adjustable strip light brightness

DS-K3G501S Series Tripod Turnstile Quick Start Guide

2

Chapter 2 System Wiring

The preparation before installation and general wiring.

Steps 1. Draw a central line on the installation surface of the left or right pedestal. 2. Draw other parallel lines for installing the other pedestals.

Note The distance between the nearest two line is 782 mm. L represents the lane width.

3. Slotting on the installation surface and dig installation holes according to the hole position diagram.

Figure 2-1 Hole Position Diagram 4. Bury cables. Each lane buries 1 network cable and 1 high voltage cable. For details, see the

system wiring diagram below.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

3

Figure 2-2 System Wiring Diagram

Note The suggested inner diameter of the low voltage conduit is larger than 30 mm. If the face recognition module are required to be connected on the left lane, you should

increase the conduit diameter or bury another conduit for the external cables. You should bury one network cable and one high voltage conduit for the right and middle

lane. The network cable must be CAT5e or the network cable has better performance. And the

suggested network cable length should be less than 100 m.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

4

Chapter 3 Installation

3.1 Disassemble Pedestals Before installation, you should use the key to open the pedestals. View the pictures below to find the lock holes.

Figure 3-1 Lock Holes

3.2 Install Pedestals Before You Start Prepare for the installation tools, check the device and the accessories, and clear the installation base.

Steps

Note The device should be installed on the concrete surface or other non-flammable surfaces. No face recognition terminal installed: If the installation area is too close to the wall, make sure

the distance between the pedestal and the wall should be more than 25 mm, or the surface may be scratched.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

5

Face recognition terminal installed: If the installation area is too close to the wall, make sure the distance between the pedestal and the wall should be more than 130 mm, or the surface may be scratched.

The dimension is as follows.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

6

Figure 3-2 Dimension

1. Prepare for the installation tools, check the components, and prepare for the installation base. 2. Drill holes on the ground according to the installation holes on the pedestals and insert the

expansion sleeves. 3. According to the entrance and exit marks on the pedestals, move the pedestals to the

corresponded positions.

Note Make sure the installation holes on the pedestals and the base are aligned with each other.

4. Seal the bottom of the turnstile to avoid water from entering.

Note Make sure the installation holes on the pedestals and the base are aligned with each other.

5. Secure the pedestals with expansion bolts.

Note Do not immerse the pedestal in the water. In special circumstances, the immersed height

should be no more than 690 mm. The installation footprint is as follows:

DS-K3G501S Series Tripod Turnstile Quick Start Guide

7

Figure 3-3 Installation Footprint

DS-K3G501S Series Tripod Turnstile Quick Start Guide

8

Chapter 4 General Wiring

4.1 Components Introduction By default, basic components of the turnstile are connected well. The turnstile supports wiring the AC electric supply for the whole system's power supply.

Note The voltage fluctuation of the electric supply is between 100 VAC and 220 VAC, 50 to 60 Hz.

The picture displayed below describes each component's position on the turnstile.

Figure 4-1 Components Diagram 1

4.2 Wiring Electric Supply Wire electric supply with the switch in the pedestal. Terminal L and terminal N are on the switch, while terminal PE should connect to a ground wire (yellow and green wire).

DS-K3G501S Series Tripod Turnstile Quick Start Guide

9

Warning Terminal PE should connect to a ground wire to avoid hazard when people touching the device.

Note The cable bare part should be no more than 8 mm. If possible, wear an insulation cap at the end

of the bare cable. Make sure theres no bare copper or cable after the wiring. The Terminal L and the Terminal N cannot be wired reversely. Do not wire the input and output

terminal reversely. To avoid people injury and device damage, when testing, the ground resistance of the equipotential points should not be larger than 2

4.3 Terminal Description

4.3.1 Access Control Board Terminal and BUS Description

Access Control Board Terminal Description You can view the access control board's terminals.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

10

Figure 4-2 Access Control Board Diagram

Table 4-1 Table of Access Control Board Terminal Description

Access Control Board Terminal Description

24 V Power Input +24 V Power Input

GND Grounding

Wiegand Card Reader 1

OK Indicator of Card Reader Control Output (Invalid Card Output)

ERR Indicator of Card Reader Control Output (Valid Card Output)

BZ Card Reader Buzzer Control Output

W1 Wiegand Head Read Data Input Data1

W0 Wiegand Head Read Data Input Data0

GND Grounding

DS-K3G501S Series Tripod Turnstile Quick Start Guide

11

Access Control Board Terminal Description

Wiegand Card Reader 2

OK Indicator of Card Reader Control Output (Invalid Card Output)

ERR Indicator of Card Reader Control Output (Valid Card Output)

BZ Card Reader Buzzer Control Output

W1 Wiegand Head Read Data Input Data1

W0 Wiegand Head Read Data Input Data0

GND Grounding

RS-485 Interface (In the BUS)

GND Grounding

RS-485 B- Connect to Card Reader RS485-

RS-485 B+ Connect to Card Reader RS485+

GND Grounding

RS-485 A- Connect to Card Reader RS485-

RS-485 A+ Connect to Card Reader RS485+

5 V Power Output 5 V 5 VDC Power Output

GND 5 VDC Grounding

RS-232 Interface (QR Code Scanner Interface, Parts of Interfaces are in the BUS)

GND Grounding

RS-232 G- Connect to Card Reader RS232-

RS-232 G+ Connect to Card Reader RS232+

GND Grounding

RS-232 H- Connect to Card Reader RS232-

RS-232 H+ Connect to Card Reader RS232+

Fire XF Connect to Fire Module

GND Grounding

Event Input C1 Event Alarm Input 1

GND Grounding

C2 Event Alarm Input 2

Exit Button K2 Door 2 Signal Input

GND Grounding

DS-K3G501S Series Tripod Turnstile Quick Start Guide

12

Access Control Board Terminal Description

K1 Door 1 Signal Input

Door Lock D1- Door 1 Relay Output (Dry Contact)

D1+

D2- Door 2 Relay Output (Dry Contact)

D2+

Alarm Output1/ Alarm Output 2

NO/NC1 Alarm Output Relay 1 (Dry Contact)

COM1

NO/NC2 Alarm Output Relay 2 (Dry Contact)

COM2

Network Interface LAN Network Accessing

Note The alarm input hardware interface is normally open by default. So only the normally open

signal is allowed. It can be linked to the buzzer of the card reader and access controller, and the alarm relay output and open door relay output.

The DIP of RS485 card ID is set as 1 and 4 by default. 1 is for entering, and 4 is for exiting. Set the DIP as 3 for connecting visitor card reader.

The Wiegand card reader 1 and 2 respectively refer to the entering and exiting card reader. The alarm output supports relay output. For detailed information about the DIP switch, see DIP Switch Description.

BUS Description You can use the BUS to connect card reader, fingerprint module, etc.

Table 4-2 Table of BUS Terminal Description

Terminal Group Terminal Name Color Description

Fingerprint Module Terminal Group

5V Red 5 V Power Terminal

485/232+ Purple Connect to Fingerprint Module RS-485+

485/232- Yellow Connect to Fingerprint Module RS-485-

GND Black Grounding

DS-K3G501S Series Tripod Turnstile Quick Start Guide

13

Terminal Group Terminal Name Color Description

QR Code Scanner Terminal Group

5V Red 5 V Power Terminal

232+ Blue Connect to QR Code Scanner RS-232+

232- Green Connect to QR Code Scanner RS-232-

GND Black Grounding

Tamper Terminal (Connected)

TAMPER Brown Tamper Terminal

Fan Power Terminal Group (Connected)

12_FS Red Connect to Fan

GND Black Grounding

Card Reader Terminal Group (Entrance)

12V Red 12 V Power Terminal

485/232+ Yellow Connect to Card Reader RS-485+

485/232- Blue Connect to Card Reader RS-485-

GND Black Grounding

Card Reader Terminal Group (Exit)

12V Red 12 V Power Terminal

485/232+ Yellow Connect to Card Reader RS-485+

485/232- Blue Connect to Card Reader RS-485-

GND Black Grounding

Light Board Terminal Group (Connected)

12V Red 12 V Power Terminal

485+ Yellow Connect to Light Board RS-485+

485- Blue Connect to Light Board RS-485-

GND Black Grounding

DS-K3G501S Series Tripod Turnstile Quick Start Guide

14

4.3.2 Access Control Board Serial Port ID Description

You can use the jumper cap on the access control board to switch the interface communication mode. For details about switching between RS-232 and RS-485 communication type, see Switching RS-485/RS-232 Mode.

Figure 4-3 Access Control Board

According to the picture above, the serial port 1 to 6 refers to the RS-485/RS-232 interface. You can use the jumper cap to change the communication type. The access control board descriptions are as follows: Serial Port 1

RS-485 communication interface. You can connect RS-485 card reader and so on. Serial Port 5 Jumper Cap

Use the jumper cap to switch the serial port communication mode. You can switch between the RS-485 communication mode and the RS-232 communication mode. By default, it is in RS-485 communication mode.

Serial Port 2 RS-232 communication interface. You can connect the fingerprint and so on.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

15

Serial Port 3 Jumper Cap Use the jumper cap to switch the serial port communication mode. You can switch between the RS-232 communication mode and the RS-485 communication mode. By default, it is in RS-232 communication mode. Use the serial port to connect with fingerprint module.

Serial Port 4/Serial Port 6 Jumper Cap Use the jumper cap to switch the serial port communication mode. You can switch between the RS-485 communication mode and the RS-232 communication mode. By default, it is in RS-485 communication mode. Use the serial port to connect with face recognition module.

Serial Port 7/Serial Port 8 The serial port has a fixed RS-232 communication mode. It has no jumper cap and cannot change the communication mode. The RS-232 interface's QR code transmission database should no more than 64 bit.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

16

4.3.3 RS-485 Wiring

Note There are four RS-485 interfaces, which are for connecting ID card reader, IC card reader, QR

code scanner, fingerprint and card reader, card recycler, text screen, fingerprint reader, and face recognition terminal. Take the wiring of RS-485 card reader as an example.

For details about text screen, see Configuring Screen Parameters in User Manual of iVMS-4200 AC Client Software.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

17

4.3.4 RS-232 Wiring

Note The RS-232 interfaces can connect QR code scanner, and card recycler. For details about text screen, see Configuring Screen Parameters in User Manual of iVMS-4200

AC Client Software. Take the wiring of text screen as an example.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

18

4.3.5 Wiegand Wiring

Note Connect the OK/ERR/BZ if the access controller should control the LED and buzzer of the Wiegand card reader.

4.3.6 Barrier Control Wiring

By default, the barrier has connected with the access control board. If possible, the device can connect with a third party control board to control the third party barriers. Interface D1 controls barrier opening for entrance, while interface D2 controls barrier opening for exit.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

19

Note The output signal is relay. The terminals cannot connect with the devices carrying voltage.

Entering Wiring

DS-K3G501S Series Tripod Turnstile Quick Start Guide

20

Exiting Wiring

4.3.7 Alarm Output Wiring

Note For details about changing the relay output status via the jumper cap, see Alarm Relay Output Mode (NO/NC) .

DS-K3G501S Series Tripod Turnstile Quick Start Guide

21

4.3.8 Exit Button Wiring

You can view the exit button wiring diagram.

Figure 4-4 Exit Button Wiring

DS-K3G501S Series Tripod Turnstile Quick Start Guide

22

Chapter 5 Device Settings

You can also set the turnstile to passing mode and memory mode, pair the keyfob, initialize the hardware, switching between RS-485 communication mode and RS-232 communication mode, and view relay output NO/NC diagram by setting the DIP switch on the access control board. Normal Mode: The device will work properly. Passing Mode: There are 9 passing modes, including controlled bi-direction, controlled entrance

and prohibited exit, controlled entrance and free exit, free bi-direction, free entrance and controlled exit, free entrance and prohibited exit, prohibited bi-direction, prohibited entrance and free exit.

Memory Mode: By default, the memory mode is enabled. When multiple cards are presented and authenticated, it allows multiple persons passing through the lane. When it counts the passing people number is equal to the card presented times, or no person passing through the lane after the last person passing, the barriers will be closed.

Note You can also set the DIP switch on the access control board to control the entrance and exit controlling type, keyfob pairing, etc. For details about the DIP switch value, see DIP Switch .

5.1 Pair Keyfob (Optional) Pair the remote control to the device through DIP switch to open/close the barrier remotely.

Before You Start Ask our technique supports or sales and purchase the keyfob.

Steps

Note Up to 32 keyfobs can be added to the turnstile. You can set the keyfob to one-to-one mode or one-to-many mode via the DIP switch on the

keyfob. Here takes one-to-one mode as an example to explain. For one-to-many mode, see the keyfob user manual. One-to-One Mode

By default, the keyfob is in one-to-one mode. The keyfob's DIP switch is towards 1 (OFF). The keyfob can control only one turnstile.

One-to-Many Mode The keyfob's DIP switch is ON. In this mode, the keyfob can control multiple turnstiles.

1. Power off the turnstile. 2. Set the No.4 switch of the DIP Switch on the access control board to the ON side.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

23

3. Power on the turnstile and it will enter the keyfob pairing mode. 4. Hold the Close button for more than 10 seconds. Or pair turnstile and keyfob in the client

software, see Manage Keyfob User of the user manual for more details. The keyfob's indicator of the will flash twice if the pairing is completed.

5. Set the No.4 switch to OFF, and reboot the turnstile to take effect.

Note Only one turnstile can pair the keyfob. If multiple turnstiles are in the pairing mode, the

keyfob will select only one of them to pair. For details about DIP switch value and meaning, see Access Control Board Serial Port ID Description .

6. Optional: Go to System User Keyfob User on the remote control page of the client software to delete the keyfob.

5.2 Initialize Device Steps 1. Remove the jumper cap of initialization pin on the access control board.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

24

Figure 5-1 Initialization Jumper Cap 2. Disconnect the power and reboot the device. The device buzzer buzzes a long beep. 3. When the beep stopped, plug the jumper cap back. 4. Disconnect the power and power on the device again.

Caution The initialization of the device will restore all the parameters to the default setting and all the device events are deleted.

Note Make sure no persons are in the lane when powering on the device.

5.3 Switch to RS-485/RS-232 Mode Take the Serial Port 4 and on the access control board as an example. If the Jumper cap's position is like the picture displayed below. (The black part is the jumper cap.) The serial port is in RS-485 communication mode.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

25

Figure 5-2 Jumper Cap Status of RS-485 Interface

If the Jumper cap's position is like the picture displayed below. (The black part is the jumper cap.) The serial port is in RS-232 communication mode.

Figure 5-3 Jumper Cap Status of RS-232 Interface

5.4 Alarm Relay Output Mode (NO/NC) Alarm Relay Output Mode (NO):

Alarm Relay Output Mode (NC):

DS-K3G501S Series Tripod Turnstile Quick Start Guide

26

Chapter 6 Activation

You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page.

Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: The default IP address: 192.0.0.64 The default port No.: 8000 The default user name (super administrator): admin

6.1 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN.

Before You Start Get the SADP software from the supplied disk or the official website http:// www.hikvision.com/en/ , and install the SADP according to the prompts.

The device and the PC that runs the SADP tool should be within the same subnet. The following steps show how to activate a device and modify its IP address. For batch activation and IP addresses modification, refer to User Manual of SADP for details.

Steps 1. Run the SADP software and search the online devices. 2. Find and select your device in online device list. 3. Input new password (admin password) and confirm the password.

Caution STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

Note Characters containing admin and nimda are not supported to be set as activation password.

4. Click Activate to start activation.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

27

Status of the device becomes Active after successful activation. 5. Modify IP address of the device.

1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP

address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification.

6.2 Activate Device via iVMS-4200 Client Software For some devices, you are required to create the password to activate them before they can be added to the iVMS-4200 software and work properly.

Steps

Note This function should be supported by the device.

1. Enter the Device Management page. 2. Click on the right of Device Management and select Device. 3. Click Online Device to show the online device area.

The searched online devices are displayed in the list. 4. Check the device status (shown on Security Level column) and select an inactive device. 5. Click Activate to open the Activation dialog. 6. Create a password in the password field, and confirm the password.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

28

Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.

Note Characters containing admin and nimda are not supported to be set as activation password.

7. Click OK to activate the device.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

29

Appendix A. Tips for Scanning Fingerprint

Recommended Finger Forefinger, middle finger or the third finger.

Correct Scanning The figure displayed below is the correct way to scan your finger:

You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.

Incorrect Scanning The figures of scanning fingerprint displayed below are incorrect:

DS-K3G501S Series Tripod Turnstile Quick Start Guide

30

Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again.

Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

31

Appendix B. DIP Switch

B.1 DIP Switch Description The DIP switch is on the access control board. No.1 to No 8 is from the low bit to the high bit.

When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. If you set the DIP switch like the figure displayed below, its binary value is 00001100, and its decimal value is 12.

B.2 DIP Switch Corresponded Functions The 8-bit DIP switch corresponded functions on the access control board are as follows:

Bit Device Mode Function Decimal Value Binary Value

1 to 2 Work Mode Normal Mode 0

3 Memory Mode Enable Memory Mode

0

Disable Memory Mode

1

4 Keyfob Paring Mode

Enable Keyfob Paring Mode

1

Disable Keyfob Paring Mode

0

DS-K3G501S Series Tripod Turnstile Quick Start Guide

32

Bit Device Mode Function Decimal Value Binary Value

5 to 8 Passing Mode Controlled Bi- direction

0

Controlled Entrance and Prohibit Exit

1

Controlled Entrance and Free Exit

2

Free Bi-direction 3

Free Entrance and Controlled Exit

4

Free Entrance and Prohibit Exit

5

Prohibited Bi- direction

6

Prohibit Entrance and Controlled Exit

7

Prohibit Entrance and Free Exit

8

DS-K3G501S Series Tripod Turnstile Quick Start Guide

33

Appendix C. Event and Alarm Type

Event Alarm Type

Passing Timeout None

DS-K3G501S Series Tripod Turnstile Quick Start Guide

34

Appendix D. Table of Audio Index Related Content

Index Content

1 Authenticated.

2 Card No. does not exist.

3 Card No. and fingerprint mismatch.

4 Passing timeout.

5 No permissions.

6 Authentication time out.

7 Authentication failed.

8 Expired card.

DS-K3G501S Series Tripod Turnstile Quick Start Guide

35

Appendix E. Communication Matrix and Device Command

Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices.

Figure E-1 QR Code of Communication Matrix

Device Command Scan the following QR code to get the device common serial port commands. Note that the command list contains all