Hikvision DS-K1T341AMF Terminal Quick Start Guide PDF

1 of 2
1 of 2

Summary of Content for Hikvision DS-K1T341AMF Terminal Quick Start Guide PDF

The figures are for reference only.

1 Appearance 2 Installaon

3 Wiring (Normal)

Installaon Environment: Indoor and outdoor installaon are supported. If installing the device indoors, the device should be at least 2 meters away from the light, and at least 3 meters away from the window or the door. If installing the device outdoors, you should apply Silicone sealant among the cable wiring area to keep the raindrop from entering.

The addional force shall be equal to three mes the weight of the equipment but not less than 50N. The equipment and its associated mounng means shall remain secure during the installaon. Aer the installaon, the equipment, including any associated mounng plate, shall not be damaged.

Backlight Direct Sunlight

Direct Sunlight through Window

Indirect Sunlight through Window

Close to Light

Make sure the gang box is installed on the wall.

After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen.

Use 2 supplied screws (SC-K1M46-SUS) to secure the base plate on the gang box. Route the cables through the cable hole of the mounng plate, and connect to the corresponding external devices cables. Use another 4 supplied screws (KA422-SUS)to secure the mounng plate on the base plate.

Align the device with the mounng plate and hang the terminal on the mounng plate.

Use 1 supplied screw (SC-KM3X6-H2- SUS) to secure the device and the mounng plate.

Apply Silicone sealant among the joints between the device rear panel and the wall (except the lower side) to keep the raindrop from entering. You can also install the device on the wall or other places without the gang box. For details, refer to the User Manual.

2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instrucons for using and managing the Product. Pictures, charts, images and all other informaon hereinaer are for descripon and explanaon only. The informaon contained in the Manual is subject to change, without noce, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (hps://www.hikvision.com/). Please use this Manual with the guidance and assistance of professionals trained in supporng the Product. Trademarks

and other Hikvision's trademarks and logos are the properes of Hikvision in various jurisdicons. Other trademarks and logos menoned are the properes of their respecve owners. Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED AS IS AND WITH ALL FAULTS AND ERRORS. HIKVISION MAKES NOWARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protecon During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognion features, biometrics data is stored in your device with encrypon method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image. As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protecon laws and regulaons, including without limitaon, conducng security controls to safeguard personal data, such as, implemenng reasonable administrave and physical security controls, conduct periodic reviews and assessments of the effecveness of your security controls. Scan the QR code to get the user manual for detailed informaon.

When connecng door contact and exit buon, the device and the RS-485 card reader should use the same common ground connecon. The Wiegand terminal here is a Wiegand input terminal. You should set the devices Wiegand direcon to input. If you should connect to an access controller, you should set the Wiegand direcon to Output. For details, see the user manual. The suggested external power supply for door lock is 12 V, 1 A The suggested external power supply for Wiegand card reader is 12 V, 1 A For wiring the fire system see the user manul. Do not wire the device to the electric supply directly. If the interface for network connecon is too large, you can use the supplied cable as shown below.

This scker meansHot parts! Burned fingers when handling the parts. Wait one-half hour aer switching off before handling parts.It is to indicate that the marked item can be hot and should not be touched without taking care. For device with this scker, this device is intended for installaon in a restricted access locaon, access can only be gained by service persons or by users who have been instructed about the reasons for the restricons applied to the locaon and about any precauons that shall be taken.

microUSB Interface (Use micro USB to USB cable to connect with USB interface)

Debugging Port (For debugging only)

Network Interface

Wiring Terminal

Tamper

Camera Camera

IR Light IR Light

White Light

Screen

Fingerprint Module (Supported by parts of Device Models)

Card Presenng Area

Mic

22.7 mm 12.3 mm 83.2 mm

NC) COM) NO)

You should purchase the gang box separately.

Use only power supplies listed in the user instrucons Make sure the power supply is used indoors and the working temperature is between 0 and 40

The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12 V, 0.5 A.

1. Use finger to hold the screen surface for 3 s and slide to right/le and enter the acvaon password to enter the Home page. 2. Enter the User Management page, tap + to enter the Add User page. 3. Set the user parameters according to actual needs.

Only the device with the fingerprint module support the fingerprint related funcons. 4. Tap Face and add the face informaon according to the instrucons. You can view the captured picture on the screen, Make sure the face picture is in good quality and size. For details about the ps and posions when collecng or comparing the face picture, see the contents on the right. 5. If the picture is in good condion, tap the . Or tap the to take another face picture.

6. Tap the save icon to save the sengs. Go back to the inial page to start authencaon. For other authencaon methods, see the device user manual.

User other authencaon methods if the device is affected by the light or other items. 1:N Matching: The device will compare the captured face picture with the ones in the database. 1:1 Matching: The device will compare the captured face picture with the user linked face picture.

Biometric recognion products are not completely applicable to an-spoofing environments. If yourequire a higher security level, use mulpleauthencaon modes.

Tips When Collecng/Comparing Face Picture

Expression Keep your expression naturally when collecng or comparing face pictures just like the expression in the picture on the right

Posture In order to get a good quality and accurate face picture posion your face looking at the camera when collecng or comparing face picture.

Size Make sure your face is in the middle of the collecng window.

Do not wear hat, sunglasses, or other accessories that can affect the facial recognion funcon.

Do not make your hair cover your eyes, ears, etc. and heavy makeup is not allowed.

Posions When Collecng/Comparing Face Picture

Recommended Height: 1.43 m to 1.90 m

Too High

Too Low

Too FarToo Close

0.5 m 1.2 m

0.5 m 0.5 m

1.4 m 1.4 m

1.4 m 1.4 m

4

4

Power on and wire the network cable aer installaon you should acvate the device before the first login

If the device is not acvated yet, it will enter the Acvate Device page aer powering on.

Steps: 1. Create a password and confirm the password. 2. Tap Acvate to acvate the device.

For other acvaon methods, see the device user manual.

We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case leers, lower case leers, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can beer protect your product. Admin and nimda are not supported to be set as acvaon password.

Acvaon Set Applicaon Mode

Aer acvaon you should select an applicaon mode

Select Indoor or Others from the drop-down list and tap OK.

If you install the device indoors near the window or the face recognion funcon is note working well, select Others.

Set Administrator Steps: 1. Enter the administrators name and tap Next<

Manualsnet FAQs

If you want to find out how the DS-K1T341AMF Hikvision works, you can view and download the Hikvision DS-K1T341AMF Terminal Quick Start Guide on the Manualsnet website.

Yes, we have the Quick Start Guide for Hikvision DS-K1T341AMF as well as other Hikvision manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Guide should include all the details that are needed to use a Hikvision DS-K1T341AMF. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Hikvision DS-K1T341AMF Terminal Quick Start Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Hikvision DS-K1T341AMF Terminal Quick Start Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Hikvision DS-K1T341AMF Terminal Quick Start Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Hikvision DS-K1T341AMF Terminal Quick Start Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Hikvision DS-K1T341AMF Terminal Quick Start Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.