Hikvision DS-K1T320EX Terminal Quick Start Guide PDF

DS-K1T320 Series

1 Installation Installation Environment: Indoor use only. Avoid backlight, direct sunlight, and indirect sunlight. For Better recognition, there should be light source in or near the installation environment. The minimum bearing weight of the wall or other places should be 3 times heavier than the device weight.

Direct Sunlight Direct Sunlight through Window

Indirect Sunlight through Window

Backlight Close to Light

1 Route the cable through the cable hole of the bracket.

Wall Mounting

Base Mounting

3 Align the device with the mounting plate, and secure

3 Slide to the end to complete the installation.

2 Secure the mounting plate on the gang box with two supplied

2 Press the bracket with both hands. Make sure the rear panel of

3 Wiring

Press with Both Hands

Numeric KeyKeypad 0~9. Digits, letters, and characters can be entered in the textbox via the numeric keys. 0 is reused as space bar when not entering digits.

Exit key. Exit the current page or return to the previous page.

In the standby page, hold to enter the administrator login interface, and press to confirm. Used as confirmation and selection key after login.

Input method shifting key.

Direction Key

ESC

OK

Wiring Terminal

Face Recognition Terminal

Quick Start Guide

UD28736B-C

Gang box is not supplied.

1 Make sure the gang box is installed on the wall.

The figures are for reference only.

Control four directions: front, back, left, and right.

Delete key. Delete textbox contents.

GND

Electric Dropbolt

Power Input 12 VDC Red

Black

White/Yellow White/Purple (NC)

(COM)

Door Lock

Network Interface

Exit Button

Door Contact

Electric Strike

Power Supply

SEN GND BTN

Black Yellow/Gray

White/Red Yellow/Green

NO COM NC

COM NO NC

(NO)

NC

NO COM

2

Align the bracket with the device rear panel.

screws (SC-KA4X22). Route the cable through the cable hole, wire the cables and insert the cables in the gang box.

the device on the mounting plate with 1 supplied screw (SC-CM4X14-5T10-SUSS).

130 mm 24.7 mm

15 0 m m

Fingerprint Recognition Area (Supported by Parts of Device Models)

Network Interface

the device and the buckles of the bracket are aligned with each other. Slide and buckle the bracket along the arrow.

Bracket is optional.

2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual TheManual includes instrucons for using andmanaging the Product. Pictures, charts, images and all other informaon hereinaer are for descripon and explanaon only. The informaon contained in the Manual is subject to change, without noce, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (hps://www.hikvision.com/). Please use this Manual with the guidance and assistance of professionals trained in supporng the Product. Trademarks

and other Hikvisions trademarks and logos are the properes of Hikvision in various jurisdicons. Other trademarks and logos menoned are the properes of their respecve owners. Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED AS IS AND WITH ALL FAULTS AND ERRORS. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONGOTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protecon During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognion features, biometrics data is stored in your device with encrypon method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image. As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protecon laws and regulaons, including without limitaon, conducng security controls to safeguard personal data, such as, implemenng reasonable administrave and physical security controls, conduct periodic reviews and assessments of the effecveness of your security controls. Scan the QR code to get the user manual for detailed information.

Appearance

When connecng door contact and exit buon, the device should use the same common ground connecon. The suggested external power supply for door lock is 12 V, 1 A. Do not wire the device to the electric supply directly.

USB Interface

Screen

Keypad

Camera Supplement Light

Card Swiping Area

Debugging Port (For Debugging Only)

Tamper

Warning In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. The socket-outlet shall be installed near the equipment and shall be easily accessible. 1. Do not ingest battery. Chemical burn hazard! 2. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. 3. Keep new and used batteries away from children. 4. If the battery compartment does not close securely, stop using the product and keep it away from children. 5. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. 6. CAUTION: Risk of explosion if the battery is replaced by an incorrect type. 7. Improper replacement of the battery with an incorrect type may defeat a safeguard (for example, in the case of some lithium battery types). 8. Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion. 9. Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas. 10. Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas. 11. Dispose of used batteries according to the instructions

Caution Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Biometric recognition products cannot be completely applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. The serial port of the equipment is used for debugging only. Wall Mounting: Install the equipment according to the instructions in this manual. To prevent injury, this equipment must be securely attached to the floor/wall in accordance with the installation instructions. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. This bracket is intended for use only with equipped devices. Use with other equipment may result in instability causing injury. This equipment is for use only with equipped bracket. Use with other (carts, stands, or carriers) may result in instability causing injury.

Safety Instruction

FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see:www.recyclethis.info

Regulatory Information

Tips When Collecting/Comparing Face Picture

Expression Keep your expression naturally when collecting or comparing face pictures just like the expression in the picture on the right

Posture In order to get a good quality and accurate face picture position your face looking at the camera when collecting or comparing face picture.

Size Make sure your face is in the middle of the collecting window.

Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function.

Do not make your hair cover your eyes, ears, etc. and heavy makeup is not allowed.

Positions When Colleting/Comparing Face Picture

Recommended Height: 1.43 m to 1.90 m

Too High

Too Low

Too FarToo Close

0.5 m 1.2 m

0.5 m 0.5 m

1.4 m 1.4 m

1.4 m 1.4 m

User other authentication methods if the device is affected by the light or other items. 1:N Matching: The device will compare the captured face picture with the ones in the database. 1:1 Matching: The device will compare the captured face picture with the user linked face picture.

Biometric recognition products cannot be completely applicable to anti- spoofing environments. If you require a higher security level, use multiple authentication modes.

1. Hold OK and login the device to enter the home page. 2. Select User -> Add User to enter the Add User page. 3. Set the user parameters according to actual needs.

Only the device with the fingerprint module support the fingerprint related functions. 4. Select Face and add the face information according to the instructions. You can view the captured picture on the screen. Make sure the face picture is in good quality and size. For details about the tips and positions when collecting or comparing the face picture, see the contents on the right. 5. Press OK to save the face picture. Or press ESC to select Retake and adjust your face position to add the face picture again.

6. Press ESC and then press OK to save the settings. Go back to the initial page to start authentication. For other authentication methods, see the device user manual.

4 Quick Operation

STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

Activation via Device

After powering on, you will enter the activation page.

Enter password and press "OK" to confirm password.

Press to shift input method.

Characters containing admin and nimda a